User manual Ceramic Glass Hob EHC644BA EHC944BA

User manual
Ceramic Glass Hob
EHC644BAEHC944BA
2
3
WE’RE THINKING OF YOU
hank you for purchasing an Electrolux appliance.
T
You’ve chosen a product that brings with it decades
of professional experience and innovation. Ingenious
and stylish, it has been designed with you in mind.
So whenever you use it, you can be safe in the
knowledge that you’ll get great results every time.
Welcome to Electrolux.
BEFORE USING YOUR APPLIANCE
efore you use the cooktop, we recommend that you
B
read through the whole user manual which provides the
description of the cooktop and its functions. To avoid
the risks that are always present when you use a gas
appliance, it is important that the cooktop is installed
correctly and that you read the safety instructions carefully
to avoid misuse and hazards.
For future reference, please store this booklet in
a safe place.
CONDITIONS OF USE
This appliance is intended to be used in household and
similar applications such as:
• Staff kitchen areas in shops, offices and
other working environments
• Farm houses
• By clients in hotels, motels and other residential
type environments
• Bed and breakfast type environments
BEFORE YOU CALL
Please ensure you read the instruction manual fully before
you call for service, or a full service fee could be applicable.
Record model and serial
number here:
Model:
Serial No:
Contents
3
Safety information
5
Product description
8
Operating instructions
12 Tips on cooking and frying
13 Care and cleaning
safety information
lease read the user manual carefully and store in a handy
P
place for later reference. Pass the user manual on to
possible new owners of the cooktop.
Read the following carefully to avoid damage or injury.
14 Troubleshooting
This symbol indicates never to do this
15 Technical data
This symbol indicates always do this
LEGEND
Warning!
This symbol indicates information concerning your
personal safety.
Caution!
This symbol indicates information on how to avoid
damaging the cooktop.
Important!
This symbol indicates tips and information about use of
the cooktop
ENVIRONMENT!
This symbol indicates tips and information about
economical and ecological use of the cooktop.
Only use the appliance for domestic cooking tasks..
Do not use the appliance as a work or a storage
surface.
General safety
Warning!
Please comply with these instructions. If you do not, any
damage resulting is not covered by the warranty.
Other than the connection point in the terminal
block, do not let the electrical supply cord touch the
appliance or hot cookware. Ensure electrical supply
cord is not tangled.
18 Notes
19 Warranty
Always monitor the appliance during operation. Do
not use an external timer or a separated remote
control system to operate the appliance.
Do not put or keep very flammable liquids and
materials, or fusible objects (made of plastic or
aluminium) on or near the appliance.
16 Installation instructions
17 Assembly
Correct operation
Correct use
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
General safety
The appliance may only be installed and connected
by trained, registered service engineers.
Built-in appliances may only be used after they
have been built into suitable built-in units and work
surfaces that meet standards.
This appliance should be used only for normal
domestic cooking and frying of food.
In the event of faults with the appliance or damage
to the glass ceramic (cracks, scratches or splits), the
appliance must be switched off and disconnected
from the electrical supply, to prevent the possibility of
an electric shock.
The appliance must not be used as a work surface
or as a storage surface.
Repairs to the appliance must only be carried out by
trained registered service engineers.
Do not leave the appliance unattended during
operation.
Additions or modifications to the appliance are not
permitted.
Do not place or store flammable liquids, highly
inflammable materials or fusible objects (e.g. plastic
film, plastic, aluminium) on or near the appliance.
Children’s safety
The cooking zones will become hot when you cook.
Therefore, always keep small children away from the
appliance.
The appliance is not intended for use by young
children or infirm persons without supervision.
Children should be supervised to ensure that they
do not play with the appliance.
Warning!
Accessible parts will become hot during use. To avoid
burns young children should be kept away
Safety during use
Remove stickers and film from the glass ceramic.
There is the risk of burns from the appliance if used
carelessly.
Cables from electrical appliances must not touch the
hot surface of the appliance or hot cookware.
Overheated fats and oils can ignite very quickly.
Warning! Fire hazard!
Switch the cooking zones off after each use.
Warning!
If the surface is cracked, switch off the appliance to
avoid possibility of electric shock.
4
5
safety information
Product description
Safety when cleaning
Cooking surface layout
For cleaning, the appliance must be switched off
and cooled down.
For safety reasons, the cleaning of the appliance
with steam jet or high pressure cleaning equipment
is not permitted.
EHC644BA
1
2
How to avoid damage to the appliance
1
The glass ceramic can be damaged by objects
falling onto it.
2
3
The edge of the glass ceramic can be damaged by
being knocked by the cookware.
Cookware made of cast iron, cast aluminium or with
damaged bottoms can scratch the glass ceramic if
pushed across the surface.
Before spillage can become burnt on to the cooking
surface, remove it with a damp cloth.
4
5
/210
75
20/1
1
To avoid damaging cookware and glass ceramics,
do not allow saucepans or frying pans to boil dry.
mm
Single cooking zone 1200W
Single cooking zone 1800W
Single cooking zone 1200W
Control panel
Triple cooking zone 2300/1600/800W
3
5
4
Do not use the cooking zones with empty cookware
or without cookware.
Do not let cookware boil dry to prevent damage to
cookware and the ceramic glass.
Do not cover the parts of the appliance with
aluminium foil.
Please note: Damage including broken glass or
scratches caused by misuse outlined above is not
covered under warranty.
EHC944BA
1
2
1
2
3
4
5
m
10 m
5/2
0/17
12
5
3
4
Single cooking zone 1200W
Single cooking zone 1200W
Single cooking zone 1800W
Control panel
Triple cooking zone 2300/1600/800W
6
7
Product description
Product description
Control panel layout
Heat setting displays
Display
1
2
3
4
Description
5
Cooking zone is switched off
Keep warm setting
Keep warm setting is set
Heat settings
Heat setting is set
Automatic warm up function
Automatic warm-up function is activated
Error
Malfunction has occurred
Residual heat
Cooking zone is still hot
Child safety device
Lock/child safety device is activated
Automatic switch off
Switch off is active
Residual heat indicator
8
1
2
3
4
5
6
7
8
7
6
Warning!
Risk of burns from residual heat. After being switched
off, the cooking zones need some time to cool down.
Look at the residual heat indicator .
Lock with pilot light
Display
Cooking zone indicators of Timer
Timer display
Heat setting selection
Timer
Triple ring cooking zone
On/Off with power indicator
Important!
Residual heat can be used for melting and keeping
food warm.
Touch Control sensor fields
The appliance is operated using Touch Control sensor
fields. Functions are controlled by touching sensor fields
and confirmed by displays and acoustic signals. Touch
the sensor fields from below, without covering other
sensor fields.
Sensor field
Function
On / Off
To switch the appliance on and off
Increase settings
To increase heat settings
Reduce settings
To reduce heat settings
Timer
To select timer settings
Increase settings
To increase Timer time
Reduce settings
To reduce Timer time
Lock
To lock/unlock the control panel
Triple ring switch
To switch outer rings on and off
8
9
Operating instructions
Operating instructions
Switching the appliance on and off
Using the automatic warm-up function
Control panel
Display
Pilot light
Switch on
Touch
for 2 seconds
/
lights up
Switch off
Touch
for 2 seconds
/ none
goes out
Control panel
Important!
After switching on, within approx. 10 seconds a heat setting or
a function must be set, otherwise the appliance automatically
switches itself off.
Control panel
to
To decrease
Touch
to
To switch off
Touch and at the same time
Important!
The keep warm setting
keep food warm.
lies between
and
to
Switch off
Touch
to
Not used
Touch
to
)
Important!
If there is still residual heat on the cooking zone (display
the automatic warm up is not performed.
The length of time that the automatic warm up function
. It is used to
1:00
By switching the outside rings on or off, the effective heating
surface can be matched to the size of the cookware.
1:40
Triple cooking zone
Sensor panel
Power Indicator
To switch on the middle ring
Touch
for 1-2 seconds
One power indicator is lit
To switch on the outside ring
Touch
for 1-2 seconds
Two power indicators are lit
To switch off the outside ring
Touch
for 1-2 seconds
The second power indicator goes out
To switch off the middle ring
Touch
for 1-2 seconds
The first power indicator goes out
/
to
to
),
Touch
Important!
When you switch the appliance off, the locking function is
automatically switched off.
10:10
2:00
3:30
4:30
The child safety device prevents unintentional use of the
appliance.
Switching on the child safety device:
The control panel, with the exception of the “On/Off” sensor
field, can be locked at any time in order to prevent the settings
being changed e.g. by wiping over the panel with a cloth.
Touch
6:30
The child safety device
Locking/unlocking the control panel
Control panel
4:50
---
Important!
Before an outside ring can be switched on, the inside ring
must be switched on.
Switch off
(after 5 seconds)
Heat setting
Length of the automatic warm up (min:sec)
operates
depends on the heat setting selected.
0:30
Switching the outside ring on and off
Switch on
Pilot light
Important!
If during the automatic warm up a higher heat setting
is selected, e.g. from to , the automatic warm up
is adjusted.
Indicator
Touch
Display
Touch
Switch on (only when starting at
Setting the heat setting
To increase
All cooking zones are equipped with an automatic warm
up function When setting a heat setting using , when
starting from , the cooking zone switches to full power
for a certain amount of time and then automatically
switches back to the heat setting set.
Display
(for 5 seconds)
the previously set heat setting
• Start the hob with . Do not set the heat settings.
• Touch for 4 seconds. The symbol comes on.
• The child safety device is switched on.
Switching off the child safety device:
• S
tart the hob with . Do not set the heat settings.
Touch for 4 seconds. The symbol comes on.
• Stop the hob with .
• The child safety device is switched off.
Important!
The child safety device can only be switched on and off, if no
heat setting is set.
Overriding the child safety device:
The child safety device can be switched off in this way for
a single cooking session; it remains activated afterwards.
• Start the hob with . The symbol comes on.
• Touch for 4 seconds. The symbol comes on.
Until the appliance is next switched off, it can used as
normal. After switching off the appliance, the child safety
device is active again.
Important!
After overriding the child safety device, a heat setting or a
function must be set within approx. 10 seconds, otherwise the
appliance automatically switches itself off.
10
11
Operating instructions
Operating instructions
Using the timer
Changing the time
Function
Condition
Outcome after the time has elapsed
Automatic cut-out
A heat setting is set
Acoustic signal
flashes Cooking zone switches off
Countdown timer
Cooking zones not in use
Acoustic signal
flashes
Important!
If a heat setting is set on this cooking zone in addition to a
countdown timer, the cooking zone is switched off after the
time set has elapsed.
Important!
If a cooking zone is switched off, the timer function set is also
switched off.
Step
Control panel
Display
1
Touch
once
Pilot light of the first cooking zone flashes
2
Touch
once
Pilot light of the second cooking zone flashes
3
Touch
once
Pilot light of the third cooking zone flashes
4
Touch
once
Pilot light of the fourth cooking zone flashes
Important!
If the pilot light is flashing more slowly, the heat setting can be
set or modified.
Important!
If other timer functions are set, after a few seconds the
shortest remaining time of all the timer functions is displayed
and the corresponding pilot light flashes.
Setting the time
Step
Control panel
1
Select
cooking zone
2
Touch
or
Indicator
Pilot light for the cooking zone selected flashes
to
minutes
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Switching off the timer function
Step
Control panel
1
Select
2
Touch
cooking zone
Indicator
Pilot light for the cooking zone selected flashes
The time remaining counts backwards to
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Step
Control panel
1
Select
cooking zone
2
Touch
or
Indicator
Pilot light of the selected cooking zone flashes faster.
Time remaining is displayed
to
minutes
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Displaying the time remaining for a cooking zone
Control panel field
cooking zone
Select
Display
Pilot light of the cooking zone selected flashes
faster The time remaining is displayed
After a few seconds the pilot light flashes more slowly.
Switching off the acoustic signal
Control panel field
Display
Touch
The acoustic signal to acknowledge.
The acoustic signal stops.
Automatic switch off
Cooking surface
• If after switching on the cooking surface, a heat
setting is not set for a cooking zone within approx. 10
seconds, the cooking surface automatically switches
itself off.
• If one or more sensor fields are covered by objects (a
pan, cloths, etc.) for longer than approx. 10 seconds,
a signal sounds and the cooking surface switches off
automatically.
• If all cooking zones are switched off, the cooking
surface automatically switches it- self off after approx.
10 seconds.
Heat setting
,
-
Control panel
hen the appliance is switched off, if one or more of the
W
sensor fields on the control panel are covered for more
that 10 seconds, an acoustic signal sounds. The acoustic
signal switches itself off automatically when the sensor
fields are no longer covered.
Cooking zones
If one of the cooking zones is not switched off after
a certain time, or if the heat setting is not modified,
the relevant cooking zone switches off automatically.
is displayed. Before being used again, the cooking zone
must be set to .
Switches off after
6 hours
-
5 hours
-
4 hours
-
1.5 hours
12
13
Tips on cooking and frying
care and cleaning
Information on acrylamides
According to the latest scientific knowledge, intensive
browning of food, especially in products containing
starch, can constitute a health risk due to acrylamides.
Therefore we recommend cooking at the lowest possible
temperatures and not browning foods too much.
Cookware
• Y
ou can recognise good cookware from the bottoms
of the pans. The bottom should be as thick and flat
as possible.
• Cookware made of enamelled steel or with aluminium
or copper bottoms can leave discolorations on the
glass ceramic surface which are difficult or impossible
to remove.
Warning!
Watch out! Risk of burns from residual heat.
Warning!
Sharp objects and abrasive cleaning materials will damage the
appliance. Clean with water and washing up liquid.
Warning!
Sharp cleaning agents will damage the appliance. Remove
residues with water and washing up liquid.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth and a little
washing up liquid.
2. Rub the appliance dry using a clean cloth.
Energy saving
• Always place cookware on the cooking zone before it
is switched on.
• Switch cooking zones off before the end of the
cooking time, to take advantage of residual heat.
• If possible, always place lids on the pans.
Removing deposits
Type of dirt
• B
ottom of pans and cooking zones should be the
same size.
Remove
At once
When the appliance has cooled down
Sugar, food containing sugar
Yes
---
A scraper1)
Plastics, tin foil
Yes
---
A scraper1)
Limescale and water rings
---
Yes
Cleaner for glass ceramic
or stainless steel1)
Fat splashes
---
Yes
Cleaner for glass ceramic
or stainless steel1)
shiny metallic discoloration
---
Yes
Cleaner for glass ceramic
or stainless steel1)
1)
Using
*Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialized shops.
Removing deposits
1. Place a scraper on the glass ceramic surface at an
angle.
2. Removeresidues by sliding the blade over the surface.
3. Wipe the appliance with a damp cloth and a little
washing up liquid.
4. Rub the appliance dry using a clean cloth.
Important! Remove stubborn residues with a cleaner for glass ceramic
or stainless steel.
Important!
Scratches or dark stains on the glass ceramic that cannot
be re- moved do not however affect the functioning of
the appliance.
Warning!
Residues from cleaning agents will damage the appliance.
Remove residues with water and washing up liquid.
14
15
troubleshooting
Technical data
Problem
Possible cause
Red rings, limescale or water rings,
shiny metallic or other discolouration,
scratches/shadows, bubbles or other
miscellaneous marks or stains on
ceramic glass cooktop surface.
Pitting of ceramic glass surface.
The cooking zones will not switch on
or are not functioning.
Remedy
Model
EHC644BA
EHC944BA
Cooktop surface has not been cleaned
Use a ceramic glass cleaner such as
correctly. Cleaning/ maintenance of the
Cerapol.
cooktop surface is not covered under
warranty. If a service call is placed to clean
the cooktop you will be charged for the visit.
PNC
949 163 264
949 163 265
Product dimensions (w x d) mm
590 x 520
900 x 520
Cut-out dimensions (w x d) mm
560 x 490 (485)
880 x 490 (485)
Voltage (volts)
230
230
Spillovers of liquid with high sugar content.
Cycles (Hz)
50
50
Service Cord
Not fitted
Not fitted
• More than 10 seconds have passed
since the appliance was switched on.
• The child safety device is switched on
These types of spills must be removed
immediately with a special scraper for
the glass. If not permanent damage to
the cooktop glass can occur which is
not covered under warranty.
Elements
No. zones
Watts
No. zones
Watts
Left front
3
2300/1600/800
3
2300/1600/800
Switch the appliance on again.
Left rear
1
1200
1
1200
Right front
1
1200
1
1200
Right rear
1
1800
1
1800
. Deactivate the child safety device (See
the section “Child safety device”).
• Several sensor fields were touched at the Only touch one sensor field.
same time.
• Automatic switch off has been triggered.
• The lock is switched on
Remove any objects (pan, cloths, etc.)
that are lying on the control panel.
Switch the appliance on again.
Switch off the lock (See the section
“Locking/unlocking the control panel”).
.
Acoustic signal sounds when
appliance is switched off.
The control panel is wholly or partly
covered by objects.
Remove objects.
The residual heat indicator is not
displaying anything.
The cooking zone was only on for a short
time and is therefore not hot.
If the cooking zone is supposed to
be hot, call the Customer Service
Department.
The automatic warm up function is
not switching itself on.
• There is still residual heat on the
cooking zone .
Let the cooking zone cool down.
• The highest heat setting is set
Acoustic signal sounds and
appliance switches itself on and then
off again; after 5 seconds another
acoustic signal sounds.
is lit.
and number are displayed.
.
The highest heat setting has the same
power as the automatic warm up
function.
• The heat setting was set using the
sensor field .
1. Switch off the cooking zone
2. Set the cooking zone using the
sensor field .
The On/Off sensor field has been covered
up, e.g. by a cloth.
Do not place any objects on the control
panel.
• Overheating protection for the cooking
zone has been triggered.
Switch off the cooking zone. Switch the
cooking zone on again.
• Automatic switch off has been triggered.
Switch off the cooking zone. Switch the
cooking zone on again.
Electronics fault.
Disconnect the appliance from the
electrical supply for a few minutes
(Take the fuse out of the house’s wiring
system) If after switching on again,
is displayed again, call the customer
service department.
If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer
Care Department.
Warning!
Repairs to the appliance are only to be carried out by
qualified service engineers. Considerable danger to
the user may result from improper repairs.
Important!
If the appliance has been wrongly operated, the visit from the
customer service technician or dealer may not take place free of
charge, even during the warranty period.
Total
6500
ENVIRONMENT!
Disposal
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more
detailed information about recycling of this product, please
contact your local council, your household waste disposal
service or the shop where you purchased the product.
Packaging material
The packaging materials are friendly to the environment and
can be recycled. The plastic components are identified by
marking: >PE<,>PS<, etc. Discard the packaging materials
as household waste at the waste disposal facilities in your
municipality.
6500
16
17
Installation Instructions
Warning!
This must be read! The laws, ordinances, directives
and standards in force in the country of use are to
be followed (safety regulations, proper recycling in
accordance with the regulations, etc.)
Important!
Installation may only be carried out by a qualified electrician.
The minimum distances to other appliances and units are to
be observed.
Anti-shock protection must be provided by the installation, for
example drawers may only be installed with a protective floor
directly underneath the appliance.
The cut surfaces of the worktop are to be protected against
moisture using a suitable sealant. The sealant seals the
appliance to the work top with no gap. Do not use silicon
sealant between the appliance and the work top. Avoid
installing the appliance next to doors and under windows.
Otherwise hot cookware may be knocked off the rings when
doors and windows are opened.
Warning!
Risk of injury from electrical current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of voltage.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to the electrical
supply by a qualified electrician.
• Loose and inappropriate plug and socket connections
can make the terminal overheat.
• Have the clamping connections correctly installed by a
qualified electrician.
• Use strain relief clamp on cable.
Warning!
The surface temperature exceeds 95°C. To avoid a
hazard, underbench access must be restricted.
Electrical Connection
Before connecting, check that the nominal voltage of
the appliance, that is the voltage stated on the rating
plate, corresponds to the available supply voltage. Also
check the power rating of the appliance and ensure that
the wire is suitably sized in accordance with local wiring
rules to suit the appliance power rating. The rating plate
is located on the lower casing of the hob. The heating
element volt- age is AC230V~. The appliance also works
perfectly on networks with AC220V~ or AC240V~. Means
for disconnection must be incorporated in the fixed
wiring in accordance with local wiring rules.The hob is
to be connected to the mains using a device that allows
the appliance to be disconnected from the mains at all
poles with a contact opening width of at least 3 mm, eg.
automatic line protecting cut-out, earth leakage trips or
Assembly
fuse. If this appliance’s mains cable is damaged, it must
be replaced by a special cable (type H05BB-F Tmax
90°C; or higher). The latter is available from the Customer
Care Department. The connection must be carried out
as shown in the diagram. The connecting links should be
fitted according to the appropriate connection diagram.
The earth lead is connected to terminal. The earth lead
must be longer than leads carrying electric current. The
cable connections must be made in accordance
with regulations and the terminal screws tightened
securely. Finally, the connecting cable is to be secured
with the mains cable cleat and the covering closed by
pressing firmly (lock into place). Before switching on for the
first time, any protective foil or stickers must be removed
from the glass ceramic surface.
Warning!
Once connected to the mains supply check that all
cooking zones are ready for use by briefly switching
each on in turn at the maximum setting.
• A duplicate rating label is supplied with this unit. For
easy identification of this unit after installation, stick it to
a readily available surface adjacent to the cooktop.
EHC644BA
Sticking on the seal
• C
lean the worktop around the cutout area.
• Stick the single-sided adhesive sealing tape provided
on the underside of the hob around the outside edge
ensuring that it is not stretched. The two ends of
the tape should join in the middle of one side. After
trimming the tape (allow it to overlap by 2-3 mm), press
the two ends together.
Important!
The cut-out section in the worktop is illustrated in the
drawing with the dimensions 560 x 490 / 880 x 490 mm.
The appliance can also be built into a shorter cut-out
section with the dimensions 560 x 485 / 880 x 485 mm.
Warning!
Surface temperatures of base exceed 95°C, under
bench access must be restricted by use of noncombustible barrier on installation
EHC944BA
18
19
Notes
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: BUILT-IN OVEN, COOKTOP
AND FLOOR MOUNTED COOKER
This document sets out the terms and conditions of the product
warranties for Electrolux Appliances. It is an important document.
Please keep it with your proof of purchase documents in a safe place
for future reference should you require service for your Appliance.
1. In this warranty
(a) ‘acceptable quality’ as referred to in clause 10 of this warranty has
the same meaning referred to in the ACL;
(b) ‘ACL’ means Trade Practices Amendment (Australian Consumer
Law) Act (No.2) 2010;
(c) ‘Appliance’ means any Electrolux product purchased by you
accompanied by this document;
(d) ‘ASC’ means Electrolux’ authorised service centres;
(e) ‘Electrolux’ means Electrolux Home Products Pty Ltd of 163
O’Riordan Street, Mascot, NSW 2020, ABN 51 004 762 341 in
respect of Appliances purchased in Australia and Electrolux (NZ)
Limited of 3-5 Niall Burgess Road, Mount Wellington, in respect
of Appliances purchased in New Zealand;
(f) ‘major failure’ as referred to in clause 10 of this warranty has the
same meaning referred to in the ACL and includes a situation when
an Appliance cannot be repaired or it is uneconomic for Electrolux, at
its discretion, to repair an Appliance during the Warranty Period;
(g) ‘Warranty Period’ means:
(i) where the Appliance is used for personal, domestic or household
use (i.e. normal single family use) as set out in the instruction
manual, the Appliance is warranted against manufacturing
defects in Australia for 24 months and in New Zealand for 24
months, following the date of original purchase of the Appliance;
(ii) where the Appliance is used for commercial purposes (including
being used to directly assist a business or where the Appliance is
used in a multi-family communal or share type environment), the
Appliance will then be warranted against manufacturing defects
in Australia for 3 months and in New Zealand for 3 months,
following the date of original purchase of the Appliance.
(h) ‘you’ means the purchaser of the Appliance not having purchased
the Appliance for re-sale, and ‘your’ has a corresponding meaning.
2. This warranty only applies to Appliances purchased and used in Australia
or New Zealand and is in addition to (and does not exclude, restrict, or
modify in any way) any non-excludable statutory warranties in Australia
or New Zealand.
3. During the Warranty Period Electrolux or its ASC will, at no extra charge
if your Appliance is readily accessible for service, without special
equipment and subject to these terms and conditions, repair or replace
any parts which it considers to be defective. Electrolux or its ASC may
use remanufactured parts to repair your Appliance. You agree that
any replaced Appliances or parts become the property of Electrolux.
This warranty does not apply to light globes, batteries, filters or similar
perishable parts.
4. Parts and Appliances not supplied by Electrolux are not covered by
this warranty.
5. You will bear the cost of transportation, travel and delivery of the
Appliance to and from Electrolux or its ASC. If you reside outside of the
service area, you will bear the cost of:
6. Proof of purchase is required before you can make a claim under
this warranty.
7. You may not make a claim under this warranty unless the defect claimed
is due to faulty or defective parts or workmanship. Electrolux is not liable
in the following situations (which are not exhaustive):
(a) the Appliance is damaged by:
(i) accident
(ii) misuse or abuse, including failure to properly maintain or service
(iii) normal wear and tear
(iv) power surges, electrical storm damage or incorrect power supply
(v) incomplete or improper installation
(vi) incorrect, improper or inappropriate operation
(vii) insect or vermin infestation
(viii) failure to comply with any additional instructions supplied with
the Appliance;
(b) the Appliance is modified without authority from Electrolux in writing;
(c) the Appliance’s serial number or warranty seal has been removed
or defaced;
(d) the Appliance was serviced or repaired by anyone other than
Electrolux, an authorised repairer or ASC.
8. This warranty, the contract to which it relates and the relationship
between you and Electrolux are governed by the law applicable where
the Appliance was purchased. Where the Appliance was purchased in
New Zealand for business purposes the Consumer Guarantee Act does
not apply.
9. To the extent permitted by law, Electrolux excludes all warranties and
liabilities (other than as contained in this document) including liability for
any loss or damage whether direct or indirect arising from your purchase,
use or non use of the Appliance.
10. For Appliances and services provided by Electrolux in Australia,
the Appliances come with a guarantee by Electrolux that cannot be
excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to
have the Appliance repaired or replaced if the Appliance fails to be of
acceptable quality and the failure does not amount to a major failure.
The benefits to you given by this warranty are in addition to your other
rights and remedies under a law in relation to the Appliances or services
to which the warranty relates.
11. At all times during the Warranty Period, Electrolux shall, at its discretion,
determine whether repair, replacement or refund will apply if an
Appliance has a valid warranty claim applicable to it.
12. For Appliances and services provided by Electrolux in New Zealand,
the Appliances come with a guarantee by Electrolux pursuant to the
provisions of the Consumer Guarantees Act, the Sale of Goods Act and
the Fair Trading Act.
13. To enquire about claiming under this warranty, please follow these steps:
(a) carefully check the operating instructions, user manual and the terms
of this warranty;
(b) have the model and serial number of the Appliance available;
(c) have the proof of purchase (e.g. an invoice) available;
(a) travel of an authorised representative;
(b) transportation and delivery of the Appliance to and from Electrolux or
its ASC,
In all instances, unless the Appliance is transported by Electrolux or an
Electrolux authorised representative, the Appliance is transported at the
owner’s cost and risk while in transit to and from Electrolux or its ASC.
(d) telephone the numbers shown below.
14. You accept that if you make a warranty claim, Electrolux and its ASC
may exchange information in relation to you to enable Electrolux to meet
its obligations under this warranty.
Important Notice
Before calling for service, please ensure that the steps listed in point 13 above have been followed.
FOR SERVICE
or to find the address of your nearest
state service centre in Australia
PlEASE CAll 13 13 49
For the cost of a local call (Australia only)
FOR SERVICE
or to find the address of your nearest
authorised service centre in New Zealand
FREE CAll 0800 10 66 10
(New Zealand only)
GOV_Warr_Apr11
SERVICE AUSTRAlIA
ELECTROLUX HOME PRODUCTS
www.electrolux.com.au
SERVICE NEW ZEAlAND
ELECTROLUX HOME PRODUCTS
www.electrolux.co.nz
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in Australia
PlEASE CAll 13 13 50
For the cost of a local call (Australia only)
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in New Zealand
FREE CAll 0800 10 66 20
(New Zealand only)
20
Electrolux Home Products Australia
telephone: 1300 363 640
fax:
1800 350 067
email:customercare@electrolux.com.au
web:www.electrolux.com.au
Electrolux Home Products New Zealand
telephone: 0800 234 234
fax:
0800 363 600
email:customercare@electrolux.co.nz
web:www.electrolux.co.nz
The Thoughtful Design Innovator.
Do you remember the last time you opened a gift that made you say
“Oh! How did you know? That’s exactly what I wanted!” That’s the kind
of feeling that the designers at Electrolux seek to evoke in everyone who
chooses or uses one of our products. We devote time, knowledge, and
a great deal of thought to anticipating and creating the kind of appliances
that our customers really need and want.
This kind of thoughtful care means innovating with insight. Not design for design’s
sake, but design for the user’s sake. For us, thoughtful design means making
appliances easier to use and tasks more enjoyable to perform, freeing our
customers to experience that ultimate 21st century luxury, ease of mind. Our aim
is to make this ease of mind more available to more people in more parts of their
everyday lives, all over the world. So when we say we’re thinking
of you, you know we mean just that.
The “Thinking of you” promise from Electrolux goes beyond meeting the needs of
today’s consumers. It also means we’re committed to making appliances safe for
the environment—now and for future generations.
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com.au or www.electrolux.co.nz
P/No. 305518307
© 2013 Electrolux Home Products Pty Ltd.
ABN 51 004 762 341
EMAN_CGH_EHC644BA_UM_Jul13
Download PDF
Similar pages