revo r322 - us drill

REVO R322 - US DRILL
OWNERS MANUAL
WARNING !
When using electric power tools
basic safety precautions should
always be used to reduce the risk
of fire, electric shock and personal
injury.
Read all of these instructions
before attempting to operate this
product and save these instructions
Machine shown
R322-US without the
safety guard for clarity.
G & J Hall Inc, 830 Hanley Industrial Court, Brentwood,
MO 63144, USA
Phone: (314) 968-5040
Email: sales@gjhalltools.com
Fax : (314) 968-5543
www.revo-tools.com
R322-US - W18XC473/US - Revised 020113
PAGE INDEX
Page No.
Machine Specification
Explanation of symbols used
Intended use of power tool
Prohibited use of power tool
3
4
5
5
Safety precautions
1 - Precautions and use of PPE.
2 - Special safety precautions - Magnetic Drills.
3 - Electrical safety
4 - Dust Extraction
5 - General safety instructions.
6
7
8
8
9-10
Installation instructions
1 - Unpacking and Assembly
2 - Setting-up or fixing tool in a stable position.
3 - Connection to power supply.
4 - Illustrated description of functions
5 - Limitations on ambient conditions
6 - Standard Accessories
7 - Disassembly and transportation
11
11
11
12
13
13
13
Operating instructions
1 - Setting and testing.
2 - Tool changing.
Mounting of cutters into the arbor.
Removing the arbor and fitting the drill chuck
Using Twist Drills.
3 - Guards
4 - Clamping of work. (Magnet Control)
14
14
15
15
16
16
5 - Limits on size of work piece and type of material.
Cutting Speeds/Materials—HSS cutters
Workpiece Material and size Limitations
17
17
6 - General instructions for use.
Drill unit spindle control
Reversing of the handles
Normal operator position
Using the drill with annular cutters
18
19
19
20
7 - Lifting handles/transportation.
5
Maintenance and servicing
1 - Regular cleaning, maintenance and lubrication.
2 - Servicing by manufacturer.
3 - Special Tools
4 - Blockages of chips or work piece fragments.
2
21
22
13
20
R322-US - W18XC473/US - Revised 020113
MACHINE SPECIFICATION
REVO
R322-US
Machine Height
Machine Width
Machine Depth
Stroke
Machine Weight
12” (slide in down position)
4 3/4” (without handles)
10 13/16”
6 1/8”
26lb (tool and detachable parts)
Rated Motor Power
Voltage
Rated Current
IP Rating
Spindle Speed - load
Spindle Speed - n0
No. of speeds
FWD/REV
Power Cord Length
Insulation Class
850W
110V / 230V AC
7.8A / 3.7A
IP20
390 rpm (depends on cutter size and feed rate)
690 rpm
Single Speed
No
8‟ 2”
CLASS I
Annular Cutter Capacity
Standard Cutting Depth
Twist Drill Capacity
Tapping Capacity
Countersink
Chuck Type
Spindle Fitting
Ø11/4”
1” (2” with optional long Arbor)
Ø1/2”
N/A
Yes
3
/4” Weldon Shank Arbor or 1/2” Chuck
1
/2” x 20 UN
Magnet Dimensions
Magnet Power
Magnetic Adhesion
Minimum Plate Thickness
6 5/16” x 3 3/8”
60W
2,200lb (measured on 1” thick plate)
1
/2” (minimum recommended)
Sound Pressure Level
Sound Power Level
SPL at Operators Head
Hand-arm Vibration
88 dBA
101 dBA
92 dBA (1.55m high x 1m distance)
Less than 2.5 m/s2
Uncertainty 3 dBA
Uncertainty 3 dBA
Uncertainty 3 dBA
Uncertainty 1.5m/s2.
The vibration measurement was made under standard conditions in accordance with the
requirements of BS EN 60129-1:2009.
The actual vibration level during use will depend on the workpiece stability/rigidity and the
condition of the cutter used. These factors may increase the vibration experienced by the
operator, each individual application of the tool should be assessed for the effect of these
application variable factors, before exposure.
.
3
R322-US - W18XC473/US - Revised 020113
EXPLANATION OF SYMBOLS USED
Symbol
Meaning
Eye protection should be worn at all times when using
this tool.
Hard Hat—Head protection should be worn at all times
whilst using this tool, to protect from overhead hazards
Ear protection / Ear defenders should be worn at all
times whilst using this tool, this tool exceed 85dB(A)
Electrical enclosure - risk of electric shock.
Read and understand the instruction manual - before
operating this tool.
Caution ! / Attention !
Instruction Manual
WEEE - Waste of Electrical and Electronic Equipment
This tool should be disposed of as Electrical &
Electronic Waste.
4
R322-US - W18XC473/US - Revised 020113
INTENDED OF USE OF POWER TOOL
This power tool is intended to be used for drilling holes with annular cutters, twist drills,
counterbores, countersinks and step drills in an industrial environment.
The machine is meant to be held onto a magnetisable surface using its electro-magnetic
base.
The power tool should be used in a weather protected environment and be used with the
accessories provided or Revo - Tools recommended accessories only.
The power tool can be used vertically, horizontally and upside down, provided the
magnetic adhesion and work environment allow.
Cutting paste should be used rather than cutting fluid when using the machine in the
upside down position to prevent ingress of fluids into the electrical system.
PROHIBITED USE OF POWER TOOL
This power tool should NEVER be used without a ground or protective earth connection.
This power tool should NOT be used in a potentially explosive environment.
This power tool should NOT be use in a wet or humid environment where water could be
drawn into the power tools cooling and ventilation system.
If the power tool is used in the upside down position, cutting fluids should not be used to
prevent ingress of fluids into the electrical system, cutting paste should be used instead.
This power tool should never be positioned on a workpiece between the electrode and
ground of an arc type welder. Damage to the machine will result as the welder will ground
through the power tools ground or earth cable.
This power tool should not be used where the voltage is abnormally lower than the rated
voltage, subject to voltage tolerances. Check the power tool rating plate, check the
voltage available.
Operating on a lower than rated voltage will result in the electro magnet being at reduced
power and the machine may become insecure whilst drilling.
LIFTING HANDLES - TRANSPORTATION
When lifting the tool
the lifting handles shown
in the diagram on the
right should be used.


The drill unit should be
lowered to its lowest
position for improved
stability.
Under no circumstances
should the motor cable
be used for lifting the
power tool.
5
R322-US - W18XC473/US - Revised 020113
PERSONAL SAFETY AND USE OF PPE carry the power tool properly with the carrying
Attention
Always watch what you are doing and use common sense at all times when operating
power tools.
Do not use the power tool whilst tired, or under the influence of drugs, alcohol or
medication.
A moment of inattention when using a power tool may result in personal injury.
Clothing
Always dress appropriately, do not wear loose clothing or jewellery.
Contain long hair, keep your hair, clothing and gloves away from any moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
Accidental Start-up
Be sure all switches are in their OFF positions before plugging in the machine.
When carrying or moving tools always keep your fingers away from the switches
Plugging in a power tool with the switches in the ON position could invite accidents.
Intentional Start-up
Before starting up the power tool always remove any adjusting keys or tools.
A wrench key left in a rotating part of the power tool may result in injury.
Over Reaching
Never over reach when using a power tool. Always ensure you have a proper stable
footing and balance at all times before operating the tool.
Proper footing and balance enables better control of the tool in case of unexpected
situations.
Personal Protective Equipment
Always wear eye protection.
Always wear ear protection.
Always wear head protection.
Always wear non-skid safety shoes.
Where appropriate wear a dust mask and gloves depending on the working environment.
WORK IN A SAFE MANNER AT ALL TIMES
6
R322-US - W18XC473/US - Revised 020113
SPECIAL SAFETY PRECAUTIONS - MAGNETIC DRILLS properly with the carrying
Safety Strap
The electro-magnet base on this power tool can release if there is a interruption in power
supply or electrical malfunction.
The safety strap provided should be used at all times to prevent the power tool from
falling in the event of power failure or electrical malfunction, possibly causing injury.
The safety cam buckle strap should be attached to the fixing points provided and checked
for security before commencing any drilling operation.
Magnetic Adhesion
The magnets strength depends on the thickness and condition of the work piece material.
Always ensure that the work piece has a minimum thickness of 1/2” to ensure there is
adequate magnetic adhesion.
If the work piece is less than 1/2” then a piece of steel plate 1/2” in thickness and larger
than the magnet footprint must be inserted to supplement the magnetic adhesion.
The surface on which the magnet is placed should be clean, flat and clear from debris or
rust. The base of the magnet should be inspected to ensure it is also clean flat and clear
of debris.
Always check the magnet is securely adhered to the work piece before commencing any
drill operations.
Do not use other appliances on the same power receptacle, any variation in voltage
cause by other appliances could result in the magnet releasing. Always us the tool on its
own power receptacle.
This power tool can be used on a vertical surface or upside down provided there is
sufficient magnetic adhesion, extra care should be taken when drilling vertically or upside
down . When using the machine vertically or upside down it is possible hot and sharp
swarf or chips may fall. Always wear appropriate personal protective equipment
When Cutting
When using coolant of lubricants, ensure coolants and lubricants do not enter the drill
units ventilation/cooling openings.
If the drill is used in the upside down position, use cutting paste instead of cutting fluid to
prevent the possibility of fluids entering the electrical system.
When using annular cutters ensure that the slug ejected at the end of the cut will not
endanger anyone in the vicinity, if working at height some form of collection device for the
ejected slug may be necessary.
Care should be taken with the ejected slug, this will be both hot and sharp, gloves should
be worn when handling the slug.
7
R322-US - W18XC473/US - Revised 020113
ELECTRICAL SAFETY
Earthing / Grounding.
.
This power tool requires a ground or earth connection.
The power tool must be plugged into an outlet properly installed and grounded or earthed
in accordance with all local codes and regulations.
Never remove or tamper with the ground or earth prong in any way.
Do not use adaptor plugs.
If the tool should electrically malfunction or breakdown, grounding or earthing will provide
a low resistance patch to carry harmful electricity away from the user.
Power Cord
Never carry the power tool by its power cord or electrical hose.
Keep power cords away from heat, oil and sharp edges.
Never pull the power cord to disconnect it from the receptacle.
Always carry the power tool properly with the carrying handles provided.
Periodically inspect the power cord for damage,
If any damage is found the power tool should not be used until the damage has been
repaired by a qualified electrician.
A damaged power cord will increase the risk of electric shock.
Using the Power Tool Outside
Do not expose the power tool to rain or wet conditions, water entering the power tool will
increase the risk of electric shock.
When operating the power tools outside, if required, an extension cord rated for outdoor
use should be used.
These extension cords are rated for outdoor use and reduce the risk of electric shock.
Electrical Enclosure
The electrical components on this power tool are housed within the main body casting,
this and the side panels of the main body create an electrical enclosure.
The panels should not be removed except by a suitable trained or qualified electrician.
DUST EXTRACTION
This tool is intended for drill holes in ferrous metals, if using on materials such as cast
iron where dust might be created, suitable dust extraction should be used.
This is both to protect the operator and to protect the motor inlet from ingress of harmful
dust particles.
Operators should wear suitable dust masks if dust is created whilst working.
8
R322-US - W18XC473/US - Revised 020113
GENERAL SAFETY
1 - Keep work area clear
Cluttered areas and benches invite injuries.
2 - Consider work area environment
Do not expose tools to rain.
Do not use tools in damp or wet locations.
Keep work area well lit.
Do not use tools in the presence of flammable liquids or gases.
3 - Guard against electric shock
Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4 - Keep other persons away
Do not let persons, especially children, not involved in the work touch the tool or the
extension cord and keep them away from the work area.
5 - Store idle tools
When not in use, tools should be stored in a dry locked-up place, out of reach of
children.
6 - Do not force the tool
It will do the job better and safer at the rate for which it was intended.
7 - Use the right tool
Do not force small tools to do the job of a heavy duty tool.
Do not use tools for purposes not intended; for example do not use circular saws to
cut tree limbs or logs.
8 - Dress properly
Do not wear loose clothing or jewellery, they can be caught in moving parts.
Non-skid footwear is recommended when working outdoors.
Wear protective hair covering to contain long hair.
9 - Use protective equipment
Use safety glasses.
Use face or dust mask if working operations create dust.
10 - Connect dust extraction equipment
If the tool is provided for the connection of dust extraction and collecting equipment,
ensure these are connected and properly used.
11 - Do not abuse the cord
Never yank the cord to disconnect it from the socket. Keep the cord away from heat,
oil and sharp edges.
.
12 - Secure work
Where possible use clamps or a vice to hold the work. It is safer than using your
hand.
13 - Do not overreach
Keep proper footing and balance at all times.
9
R322-US - W18XC473/US - Revised 020113
GENERAL SAFETY - CONT.
14 - Maintain tools with care
Keep cutting tools sharp and clean for better and safer performance.
Follow instruction for lubricating and changing accessories.
Inspect tool cords periodically and if damaged have them repaired by an authorized
service facility.
Inspect extension cords periodically and replace if damaged. Keep handles dry,
clean and free from oil and grease
.
15 - Disconnect tools
When not in use, before servicing and when changing accessories such as blades,
bits and cutters, disconnect tools from the power supply.
16 - Remove adjusting keys and wrenches
Form the habit of checking to see that keys and adjusting wrenches are removed
from the tool before turning it on.
17 - Avoid unintentional starting
Ensure switch is in "off" position when plugging in.
18 - Use outdoor extension leads
When the tool is used outdoors, use only extension cords intended for outdoor use
and so marked.
19 - Stay alert
Watch what you are doing, use common sense and do not operate the tool when
you are tired.
20 - Check damaged parts
Before further use of tool, it should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced by an
authorized service centre unless otherwise indicated in this instruction manual.
Have defective switches replaced by an authorized service centre.
Do not use the tool if the switch does not turn it on and off.
21 - Warning
The use of any accessory or attachment other than one recommended in this
instruction manual may present a risk of personal injury.
22 - Have your tool repaired by a qualified person
This electric tool complies with the relevant safety rules. Repairs should only be
carried out by qualified persons using original spare parts, otherwise this may result
in considerable danger to the user.
10
R322-US - W18XC473/US - Revised 020113
UNPACKING AND ASSEMBLY
The REVO R322-US comes in a rugged blow moulded carrying case before first use:1.
2.
3.
4.
Remove the machine from the carrying case. (Note:- 26lb weight)
Fit the three screw in handles to the pinion shaft.
Fit the safety guard as shown in the instructions, see “Using the safety guard”
Fit the arbor, as detailed in the instructions under “Fitting the Drill Chuck / Arbor”
SETTING UP THE TOOL
Before using the tool please ensure you have read the sections on the intended and
prohibited of use of the machine.
The machine should only be used for hole drilling whilst attached to the work piece by the
electro-magnetic base.
This machine is intended for use at any angle, but only if the electro-magnet is in full
working order and has sufficient hold on the work piece material.
The safety strap should be attached in case of power failure or machine malfunction.
The safety strap should NOT be used as an alternative to the magnet for clamping
purposes.
Always ensure the strap is correctly fitted and the machine is secure BEFORE starting
CONNECTION TO THE POWER SUPPLY
Connection to the power supply is by 8‟ 2” long cable and 3 pin plug.
This tool is CLASS I insulation and MUST be earthed, any power socket the tool is
connected to must have an earth.
Before the power cord is connected the magnet switch should be in the OFF position.
The power cord assembly is a custom terminated one, replacement should only be
carried out by a qualified electrician. Only use the replacement parts listed below.
Power cord part number:18X503/A
For connection information, should the power cord need to be replaced, please refer to
the wiring diagram in this manual or the connection label inside the rear panel of the
power tool.
11
R322-US - W18XC473/US - Revised 020113
ILLUSTRATED DESCRIPTION OF FUNCTIONS
PINION SHAFT
DRILL UNIT/MOTOR
HANDLE x 3
MOTOR ON/OFF SWITCH
ARBOR
MAGNET ON/OFF SWITCH
SAFETY STRAP SLOT
2A FUSE (MAGNET)
ELECTRO - MAGNET BASE
12
R322-US - W18XC473/US - Revised 020113
LIMITATIONS ON AMBIENT CONDITIONS
This power tool is has an ingress protection rating of IP20, it should not be used in dusty
or damp environments.
The power tool should be used in a weather protected environment.
Precautions should be taken to ensure dust does not enter the ventilation system of the
power tool causing clogging and overheating.
Power tools produce sparks that may ignite flammable substances such as gases,
flammable liquids or dust.
Do not operate this power tool in a potentially explosive environment.
Ambient temperatures of >113°F should be avoided.
STANDARD ACCESSORIES
The REVO R322-US is supplied in a rugged carrying case with the following as
standard :3/4” Weldon Shank Arbor (1” cut depth)
Safety Cam Buckle Strap
Safety Guard
250ml bottle & nozzle - provided for use with coolant
2.5mm, 4mm & 5mm hex key and 14mm & 20mm spanners
1/2”mm Drill Chuck and Key
DISASSEMBLY & TRANSPORTATION
When the machine is not in use it should be stored in the carrying case provided.
Any cutters should be removed after use.
The drill unit should be wound down into a low position.
The three pinion handles need to be removed before placing the tool in the case.
Any additional tools or accessories should be stored in the case.
Make sure the case is securely closed and latches are secure before lifting the carrying
case.
SPECIAL TOOLS
All tools required for the safe operation and maintenance of this power tools are provided
within the standard accessories, no additional tools should be required.
13
R322-US - W18XC473/US - Revised 020113
SETTING AND TESTING - USING THE SAFETY STRAP
A cam buckle type safety strap is provided.
The power tool has a strap slot to allow the
safety strap to be attached securely.
Always ensure the strap is correctly fitted and
the machine is secure BEFORE starting the
motor unit.
The safety strap is used to reduce the risk of
injury in the case of a power supply or
electrical malfunction.
STRAP
SLOT
CAM
BUCKLE
A correctly fitted safety strap will hold the
power tool if the electro-magnet looses its
magnetic adhesion.
If the strap becomes damaged or lost, it must
be replaced BEFORE using the power tool.
FEED
THROUGH
THIS WAY
PRESS
HERE
DO NOT use the safety strap as an
alternative clamping method, the
electro-magnet should have good magnetic
adhesion at all times whilst using this power
tool.
MOUNTING CUTTERS INTO THE ARBOR
The holder for the cutting tool is known as the
arbor. The arbor is designed to accept
Powerbor 3/4” Weldon shank annular cutters.
The Powerbor annular cutters normally have
two flats disposed at 90°to each other.
To mount the cutter.
First ensure the ejector pin is in place.
Align the flats with the two fixing screws.
Push the cutter up into the arbor until it stops.
Tighten the two fixing screws onto the cutter
flats with the hex keys supplied.
14
R322-US - W18XC473/US - Revised 020113
FITTING THE DRILL CHUCK SUPPLIED
To replace the arbor (A) with the drill chuck
supplied first remove the arbor.
To do this, using the spanners supplied, place
one spanner on the flats of the drill output
shaft.
Turn clockwise (as viewed from above) until
the spanner meets the dovetail slide.
Place the the second spanner on the flats of
the arbor, apply pressure, again clockwise as
viewed from above.
TO REMOVE
ARBOR
A
If possible the magnet can be used to hold
the machine whilst removing the arbor.
If the arbor is tight the spanner on the arbor
flats can be tapped with a soft mallet.
Once the arbor is unscrewed the arbor
support bracket (B) needs to be removed.
This is accomplished by removing the two
hexagon socket head cap screws.
B
To fit the drill chuck simply screw it into place
on the spindle nose.
Replacement of the arbor is a reversal of the
procedure above.
USING TWIST DRILLS
Twist drills can be used with the R322-US.
To accommodate twist drills, or any plain
shank cutting tool, the R322-US is supplied
as standard with a 1/2” drill chuck and key.
The drill chuck takes standard parallel shank
twist drills of up to 1/16” - 1/2”.
15
R322-US - W18XC473/US - Revised 020113
SAFETY GUARD carry the power
A safety guard is supplied with this power
tool, it should be attached BEFORE using the
power tool.
FIXING
SCREW
The guard is attached at 1 point, by a button
head screw to the motor. The nylon washer
should be closest to the guard with the spring
washer between the nylon washer and the
screw head.
The screw should be tightened just enough to
allow the spring washers to hold the guard
up.
The guard has approximately 2” of travel
which is adequate standard length cutters.
The guard should be adjusted so it is able to
slide with light pressure.
SAFETY
GUARD
CLAMPING - MAGNET CONTROL
An electro-magnet is used for clamping the tool onto the
workpiece.
MOTOR
The magnet is controlled by the magnet switch (F) located
at the bottom of the control panel.
„O‟ indicates magnet OFF „I‟ indicates magnet ON.
Ensure the magnet switch is OFF before connecting the
power supply.
Ensure the magnet is clean and free from debris and that
the machine is on a flat clean ferrous surface of the
required minimum thickness (3/8”).
G
To switch the magnet ON, press the switch to the „I‟
position, the switch will illuminate to indicate there is a
power supply to the machine.
F
The security of the magnet should always be physically
checked BEFORE starting the drill unit.
The magnet is protected by a 20mm 2A fast acting fuse (G).
16
R322-US - W18XC473/US - Revised 020113
CUTTING SPEEDS/MATERIALS—HSS CUTTERS
The REVO R322 is a single speed drill unit with a no load speed of 690 rpm and full load
speed of 390 rpm, under load the R322 will regulate its speed depending on the load
applied. ie: a small cutter will run faster than a larger cutter (if the same feed rate is
applied)
The R322 has the optimum power / torque / spindle speed for HSS annular and TCT
cutters in the range Ø1/2” to Ø 1 1/4”, cutting EN10025 S235J steel or its equivalent.
The R322 can also be used on other materials such as high tensile steel and stainless
steel if the appropriate speed for the material to be cut is selected.
Cutting Speeds—suggested speed rates for varying cutter diameters / materials
Cutting Speeds (Metric)
Cutting Speeds (Imperial)
Material
Material
Surface
Speed
(M/min)
Surface Speed
(Inches/min)
Aluminium 60
Aluminium 2.37”
Brass 45
Brass 1.75”
Mild Steel 24
Mild Steel 1.00”
High Tensile 9
0.37”
0.75”
1.25”
1.62”
2.0”
2.37”
2.75”
3.12”
High Tensile 0.37”
Cutter Diameter (inches)
WORKPIECE MATERIAL AND SIZE LIMITATIONS - MAGNET
The electro - magnet clamping force is measured as the pull off load when clamped on a
steel plate (EN10025 S235J or its equivalent) of 1” thickness, flat with a good
surface and free from rust and debris.
For any other workpiece material the clamping force will be different, any difference in
workpiece thickness and the clamping force will deviate.
The minimum recommended plate thickness for the electro-magnet is 1/2” thick.
If the workpiece is thinner than recommended then an additional plate, made of suitable
material should be added by clamping to the workpiece, this will help the electro-magnet
become more secure.
BEFORE using the drill always ensure the magnet is held onto the work piece securely.
17
R322-US - W18XC473/US - Revised 020113
OPERATION - SPINDLE - START / STOP
The drill unit or “motor” is controlled by a twin push button
switch (H) at the top of the control panel.
MOTOR
The green button is ON the red button is OFF.
The green button is below with the surrounding bezel.
The red button is raised above the surrounding bezel.
This is to prevent inadvertent operation of the drill unit.
H
The motor will not operate unless the magnet is switched
ON first.
BEFORE starting the motor, the security of the magnet
should be physically checked, if any movement is possible
this should be rectified BEFORE using the drill.
The motor control has an under-voltage relay, if the power
is interrupted the motor will stop and will not restart when
the power is resumed until the motor control is operated
again.
18
R322-US - W18XC473/US - Revised 020113
OPERATION - REVERSING OF THE HANDLES
The three handles (C) which raise and lower the drill unit
are attached to the pinion shaft (D).
D
These handles and the pinion shaft itself can be turned
around so the handles can be used on each side of the
machine. This is useful if access is limited on one side of
the machine because of the machines location.
C
The handles are normally mounted on the same side as the
controls, if they need to be reversed the following procedure
should be used.
First, the drill unit and its slide should either be supported or
put into its lowest position to prevent the risk of it falling
when the pinion is disengaged.
The hexagon head cap screw in the end of the pinion shaft
end cap (E) should be unscrewed.
E
The pinion shaft end cap can then be removed, the pinion
shaft and handle assembly can be withdrawn.
The pinion shaft and handle assembly can then be mounted
on the opposite side of the machine, taking care to ensure
the pinion gear teeth engage with the rack teeth.
The pinion shaft end cap and its hexagon head cap screw
should then be replaced and re-tightened.
OPERATION - NORMAL OPERATOR POSITION
The normal operator position is as shown in the image on
the right, in general it is best to use the machine from in
front of the control panel so that all the operator controls are
visible and easily accessed.
There are occasions with this type of machine that it is used
horizontally or even upside down. Extra care should be
taken in these circumstances and access to the machine
controls should be maintained.
The pinion shaft can be reversed on this type of machine to
allow the drill better access in confined spaces. When the
handles are reversed, again the operator should still have
full access to the control panel before using the machine.
19
R322-US - W18XC473/US - Revised 020113
OPERATION - USING THE DRILL WITH ANNULAR CUTTERS
Insert the correct pilot pin into the pilot pin hole through the shank of the cutter.
Mount the cutter in the tool holder (arbor) of the machine as described in previous
chapters, ensuring the cutter is secure and correctly fitted.
Position the machine on the work piece ensuring the magnet is on a flat clean ferrous
surface and the work piece is not below the minimum recommended thickness.
Use the pilot pin to align the centre of the cutter to the desired hole position.
Switch on the magnet and physically check the machine is securely adhered to the work
piece.
Once in position, attach the safety strap, if the magnetic adhesion fails for some reason
the safety strap will reduce movement of the machine.
Apply cutting fluid through the small holes in the arbor, the arbor has a small reservoir for
coolant which is fed down through the central pin hole to the cutter. The use of cutting
fluid will enhance the quality of the cut and prolong the life of the cutter.
Lower the safety guard provided.
Switch on the drill motor, feed the cutter down by using the three handles provided.
Proceed with caution, apply pressure gradually until the cutter has formed a groove of
approx 1/8”. Once a groove is established the pressure can be increased.
DO NOT apply excessive pressure, if excessive pressure is required it is a sign the cutter
may be worn, continuing to use a worn cutter will result in damage to the drill motor.
If the drill motor slows significantly under load ease off the downward pressure.
On deep holes it may be necessary to withdraw the cutter to remove swarf and to apply
more cutting fluid.
A cutter in good condition will need only moderate feed pressure and will produce
continuous chips or swarf. Broken chips or swarf indicate a cutter or material problem, so
care should be taken.
OPERATION - BLOCKAGES OF CHIPS AND WORKPIECE FRAGMENTS
If excessive swarf builds up during the cut it may be necessary to withdraw the cutter to
remove the swarf, care should be taken as the swarf will be both hot and sharp.
As the cutter begins to break through, the feed pressure should be reduced slightly.
When the cutter breaks through, a slug of material at the centre of the cut will be ejected.
This will be both hot and sharp. Care should be taken when handling the slug.
Care should be taken that the ejection slug is safe and can not injure anyone in the
vicinity, the slug should be prevented from falling where possible.
20
R322-US - W18XC473/US - Revised 020113
MAINTENANCE - GENERAL
To keep this machine in a safe working condition regular certain maintenance is
required.
1.
2.
3.
4.
The gib strip on the dovetail slide must be adjusted to eliminate any free play.
The dovetail slides will need to be lubricated will oil periodically.
The magnetic base should be inspected for damage on its magnetic surface or for
any damage to the resin, any damage should be repaired before using the drill.
A monthly inspection of the carbon brushes is recommended, excessive wear could
lead to motor damage or malfunction.
MAINTENANCE - REPLACING BRUSHES
The carbon brushes (M) can be removed by
simply unscrewing the brush cap (L).
The brush has a spring and metal cap
attached, simply withdraw the brush to
inspect or replace it.
M
L
When replacing the brush, slide it into the
brush holder, make sure the metal cap of
the brush seats in the recess on the brush
cap, then screw the brush cap home.
Always use genuine replacement parts.
The brushes on this drill unit have an auto
stop feature, when the brush reaches its
wear limit to motor will stop until the brushes
are replaced
ACCESSORIES
18Y170
CHUCK ADAPTOR
This allows a drill
chuck to be quickly
placed into the arbor
of the machine.
18YPIPE PIPE CLAMP
This allows the drill to be mounted
on a pipe or cylindrical object, the
magnet attaches to the “saddle” so
the material of the workpiece does
not need to be magnetic.
21
R322-US - W18XC473/US - Revised 020113
MAINTENANCE - TOOL USE AND CARE carry the power tool properly with the carrying
Always ensure the work piece is secure and stable before attempting to work on it.
Do not force the tool, always use the correct type of cutting tool for your application and
use it at the rate it was designed to work at.
Do not use the power tool if the power switch does not turn it on or off, any tool which can
not be turned on or off with the switch is dangerous and must be repaired before use.
Always disconnect the plug from the power supply before making any adjustments,
changing accessories or storing the tool. This will prevent the risk of the starting the tool
accidentally.
Always store tools not in use out of reach of children and untrained persons. Tools are
dangerous in the hands of an untrained user.
Maintain all cutting tools with care, keep them sharp and clean, properly maintained tools
with sharp edges are less likely to bind and will be easier to control.
Do not operate the power tool with dull or damaged cutting tools, this may overload the
motor.
Check the power tools periodically for misalignment or binding of moving parts, also
broken parts or any other condition that may affect the tools operation. If damaged have
the tool serviced before using, Poorly maintained tools can cause accidents.
Use only Revo - Tools recommended accessories, accessories made for other power
tools may not be suitable and could become hazardous when used.
SERVICE the power tool properly with the carrying handles provided.
Only trained repair personnel should perform tool service. Service or maintenance
performed by untrained personnel could result in a risk of injury.
When servicing the power tool, only use identical replacement parts, pay attention to the
power tools voltage rating and model number to ensure the correct replacement parts are
specified.
WARRANTY
REVO -TOOLS WARRANTY STATEMENT
Revo -Tools warrants its magnetic drills for one (1) year from the date of purchase
against defects due to faulty material or workmanship and will repair or replace (at its option) without charge, any items returned. This warranty is void if the item has been damaged by accident or unreasonable use, neglect, improper service or other causes not
arising out of defects in material workmanship. No other expressed warranty is given or
authorised. Revo - Tools disclaims any implied warranty of merchantability or fitness for
any period beyond the expressed warranty, and shall not be liable for incidental or
consequential damages. To obtain warranty service, return the item(s) to your nearest
factory authorised repair centre.
This warranty is on lieu of any other warranty, expressed or implied, including any
warranty of merchantability or fitness for a particular purpose.
22
R322-US - W18XC473/US - Revised 020113
R322 WIRING DIAGRAMS
23
R322-US - W18XC473/US - Revised 020113
REVO R322 - US
ITEM
1
Part No.
STAND PARTS
Description
18Y138/G MAIN BODY CASTING (GREY)
2
18Y134
ELECTRO-MAGNET BASE
3
18X312
BRASS GUIDES (PAIR)
4
18Y140
MACHINE RACK - INC. SCREWS
5
18X411
DOVETAIL SLIDE
6
7
18Y201
18Y130
ARBOR SUPPORT BRACKET - INC BUSH
ARBOR ASSEMBLY (1/2" X 20 UN)
8
18X321
ARBOR SPRING
9
18X323
ARBOR PISTON
10
18X206
INTERNAL CIRCLIP
11
12
18X417
18X310
SPINDLE BUSH ONLY
REVO SAFETY GUARD
13
18X311
RETAINING BRACKET
14
18X524
PINION END CAP
15
18X502
PINION BUSH
16
18Y144
PINION SHAFT - INC CAP & SCREW
17
18
17+18
19
20
21
18X718
18X520
18Y145
18X519
18X503/2
18X503/A
HANDLE
KNOB
HANDLE/KNOB COMPLETE
CORD GRIP (CABLE GLAND)
REVO CABLE FLEX TO MOTOR
MAINS CABLE 110V US
ITEM
Part No.
23
18X454
R322 REAR PANEL
24
25
18X515
18X455
RECTIFIER UNIT
R322 CONTROL PANEL (PLATE)
26
18X406
MOTOR START/STOP SWITCH - 110V
28
18X456
MAGNET SWITCH - 0 & I MARKINGS
29
18X457
R322 FUSE HOLDER
30
18X512
2A FUSE
31
18X224
M5 x 18 CONE POINT SCREW
32
18X219
M5 NUT
33
18X205
M8 X 8 SKT SCREW
34
18X430
POWER CABLE STRAIN RELIEF BUSH
18X470
18ZA02B
18Y170
18X419
PLASTIC CASE
1/2” DRILL CHUCK & KEY
CHUCK ADAPTOR - ACCESORY
SAFETY STRAP - CAM BUCKLE
NOT SHOWN
35
36
36
37
24
Description
R322-US - W18XC473/US - Revised 020113
REVO R322 - US
DRILL PARTS
ITEM
39
40
41
42
Part No.
18X451
18X432
18X433
18X5620
Description
COMPLETE DRILL UNIT - 110V
SET OF CARBON BRUSHES
BRUSH CAP
5.5mm x 25mm SCREW
NOTE: The replaceable parts for the drill unit are limited to carbon brushes, brush caps
and fixing screws only.
If the drill unit becomes unserviceable due to wear, it is normally more cost effective to
replace the entire drill unit.
25
R322-US - W18XC473/US - Revised 020113
26
R322-US - W18XC473/US - Revised 020113
27
R322-US - W18XC473/US - Revised 020113
Declaration of Conformity
On our sole responsibility we declare that this product, the REVO R322 Drill, is in
conformity with the following standards and standard documents :EN61029-1:2009
- Safety of Transportable Motor Operated Electric Tools
EN61000-6-4:2007
- Electromagnetic Compatibility (EMC). Generic standards
Emission standard for industrial environments
EN61000-6-2:2005
- Electromagnetic compatibility (EMC). Generic standards
Immunity standard for industrial environments
EN61000-6-3:2006
- Electromagnetic compatibility (EMC).
Limits for harmonic current emissions.
EN61000-3-3:2008
- Electromagnetic compatibility (EMC).
Limitation of voltage changes, voltage fluctuations and
flicker with rated current ≤ per phase and not subject
to conditional connection.
According to the regulations :2006/95/EC
- Low Voltage Directive
2004/108/EC
- EMC Directive
2006/42/EC
- Machinery Directive
2011/65/EU
- RoHS Directive (RoHS2)
Signed.............................................
(P.D.Edwards - Managing Director)
Date....23.11.11
G & J Hall Inc,
830 Hanley Industrial Court,
Brentwood, MO 63144,
USA
Phone:
Fax:
Email:
Web:
(314) 968-5040
(314) 968-5543
sales@gjhalltools.com
www.revo-tools.com
WARRANTY REGISTRATION
Thank you for purchasing your REVO-Tools magnetic based
drilling machine, to ensure any warranty claim can be
processed promptly, please register now at :http://www.revo-tools.com
Click on the button “REVO WARRANTY REGISTRATION”
28
R322-US - W18XC473/US - Revised 020113
Download PDF
Similar pages