LOGIK 60CM CHIMNEY HOOD, STAINLESS

LCH665SSE
LCH965SSE
COOKER HOOD
DOMESTIC USE
INSTRUCTION MANUAL
Satety Warnings
Safety
Before Use
• The appliance must be installed according to the manufacturer’s instructions. Improper installation may result
in injury or damge, for which the manufacturer cannot be held responsible.
• The electrical safety of this appiance is guaranteed only if it is connected to a properly earthed system which
complies with the electrical safety standards in force. If you cannot verify that this fundamental safety requirement
is in place, consult a qualified electrician. The manufacturer cannot be held responsible for an appliance which has
not been correctly earthed.
• Check that the voltage (230VoltsAC) printed on the rating label inside the cooker hood corresponds to the
mains voltage in your home. If in doubt call a qualified electrician.
• Never replace the power supply cable yourself. Damaged cables must only be replaced by an authorised
service centre.
• Adaptors, multiple sockets and/or extension leads must not be used.
• To avoid electrical shock, never touch the cooker hood or plug with wet hands.
• Ventilation outlets on the cooker hood should never be covered, as obstructions may cause overheating or fire.
• Always disconnect the plug from the mains supply before cleaning the cooker hood or carrying out
maintenance work.
• Do not flambé under the cooker hood as this may cause a fire hazard.
• Avoid leaving a gas hob on when there is no pan on the stove.
• There should be adequate ventilation of the room when the cooker hood is used at the same time as
appliances burning gas or fuel.
• Regulations concerning the discharge of air have to be fulfilled.
Operation
WARNING!
It is hazardous for anyone other than authorised service personnel to carry out servicing or repairs which involves
the removal of covers.
Cleaning, Maintenance
and Troubleshooting
To avoid the risk of an electric shock do not attempt to repair this appliance yourself.
If the supply cord is damaged it must be replaced by the manufacturer, its service agent , or similarly qualified
persons in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with reduced sensory or mental capabilities, or
lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Disposal
Old appliances still have some residual value. An environmentally friendly method of disposal will ensure that valuable raw materials can be recovered and used again. Up to date information concerning options for disposing of
your old appliance and packaging from the new one can be obtained from your local council office.
Specification
GB-2
Before use
Please read these instructions carefully before using your new Logik Cooker Hood. The Cooker Hood is for indoor,
domestic use only.
WARNING: Please be carefully when unpacking and installing this appliance as sheet metal can cause injury if not
handled with care.
Satety Warnings
Introducing Your New Cooker Hood
Before Use
Telescopic chimney flue
Control panel
120mm to 125mm ducting adaptor
Ducting adaptor
Cooker hood main body
Operation
Removable filters
Screws ST4*35 X6 ST4*18 X4 ST4*10 X2
Washers x 2
Screw plug x 6
Installation and electrical wiring must be carried out by a qualified engineer to ensure
all appliance codes and standards are followed. Before installing check that the
voltage indicated on the rating plate is suitable for your home.
Location
Rating plate
The Cooker Hood is designed to be a permanent fixture in the home, therefore needs to be located in a place that
the lowest part of the hood will be set at least 70cm above the hob.
The Cooker Hood will need to be positioned with adequate ventilation directly over the cooker. The air that is
discharged from the Cooker Hood should NOT be filtered into a flue that is used for other appliances that use gas
or other fuels. Regulations concerning the discharge of air MUST be fulfilled.
Cleaning, Maintenance
and Troubleshooting
Install Your New Cooker Hood
IMPORTANT: The Cooker Hood flue MUST NOT be connected to a previously installed appliance i.e. water, heaters,
boilers or cooker. The Cooker Hood MUST have a separate flue and MUST NOT be installed above a cooker with
eye-level grills.
Specification
IMPORTANT: Easy access to the electrical socket must be maintained to ensure that you can carry out simple
maintenance.
Before plugging in YOU MUST
Check that you have a socket, which is compatible with the Cooker Hood.
GB-3
Satety Warnings
Installation
Before beginning any installation work ensure the mains power has been turned off.
Extracted Air Installation
fig.1
Before Use
1. Using a Phillips screwdriver fix the ducting
hose connector onto the air outlet of the hood.
fig.2
Metal plate
2. Connect the hose (not supplied) to
the air duct. Use the adaptor provided to
connect to a 125mm hose (not supplied).
(refer to fig.1)
3. The ducting can pass through your wall to the outside.
Stencil
Operation
Use the stencil provided to help position the hood onto the wall directly below the ducting.
NOTE: Take extreme care when drilling holes into your wall to avoid hidden electrical wiring.
Cleaning, Maintenance
and Troubleshooting
1. With the stencil positioned on the wall, drill
4 holes onto the back wall. Push 4 raw plugs into
the drill holes and partially screw in the top 2
screws. (leaving 10mm unscrew)
2. Fix the hood onto the wall by positioning
the upper 2 screws through the key holes
on the back of the hood.
3. Attach the lower part of the hood by removing the filter panels to gain access to the lower safety screw holes.
Attaching the Chimney flue wall bracket
1. Using the wall bracket as a template, drill 2 holes into the wall and push raw plugs into the drill holes.
Specification
2. Place the wall bracket over the raw plugs
and screw into position.
GB-4
3. Screw the inner chimney flue section to the
wall bracket by ST 4X10 screw.
The telescopic chimney flue can be adjusted in height to fit your ceiling once fully attached to the wall.
Re-Circulation using Carbon filters
Two carbon filters (not supplied) can also be added to your Cooker Hood, when air is to be re-circulated instead of
external ducting. Attach to either side of the motor. Please see Partmaster Direct details on the back cover to order
them - for UK only. (2 carbon filters required)
Satety Warnings
Adjusting the telescopic hood
Before Use
Re-circulation using carbn filters
Carbon Filter
Align the rib in filter with the slot in fan guard.
Slide the filter in position.
Operation
The filter is locked.
Press the knob to release the filter.
Take out the filter.
In Use
0
= Switches the Cooker Hood off.
1
= Low speed. Is suitable when low levels of steam are created whilst cooking.
2
= Medium speed.
3
= High speed. Is suitable when high levels of steam are created whilst cooking.
Cleaning, Maintenance
and Troubleshooting
Control panel
Specification
= Switches the overhead light on.
The Cooker Hood should be left on for at least 15 minutes after cooking has finished to ensure efficient
filtering of the air.
GB-5
Satety Warnings
Cleaning
Regular cleaning will help to maintain the effectiveness of your Cooker Hood.
1. Switch off and unplug the Cooker Hood before cleaning.
2. Clean the inside and outside of the Cooker Hood with a damp cloth and a mild detergent.
NOTE: Do not use solvents or abrasives as this may damage the Cooker Hood.
Warning: Your Cooker Hood can become a fire risk if it is not cleaned correctly
Please be careful when cleaning this appliance as sheet metal can cause injury if not handled with case.
Before Use
Cleaning the filters
To ensure the filters do not become a fire hazard we recommend they are washed every 3 months. Do not check the
filter panels whilst the Cooker Hood is in use.
1. Before cleaning the filters always switch off and disconnect the electrical supply.
2. Remove the filter panels by holding down the buttons on each panel and lifting towards you. They can then
be taken out of the cooker hood.
Operation
3. Wash each filter in warm water and a mild detergent, leave to soak and drain. Ensure it is completely dry
before replacing into the Cooker Hood.
4. Place the bottom of each panel into the back of the Cooker Hood and raise the top to click into position.
NOTE: The filter panels are also dishwasher proof. The filter panels may alter in colour slightly after several washes,
this is not a fault.
Cleaning, Maintenance
and Troubleshooting
Specification
GB-6
Satety Warnings
Maintenance and Troubleshooting
Changing the internal light
Allow the Cooker hood to cool for at least 30 minutes after use before changing the light bulb.
1. Before carrying out the bulb replacement always switch off and disconnect the electrical supply.
2. Remove the removable filters by holding down the buttons on each panel and lifting towards you.
They can then be taken out of the Cooker hood.
3. Remove the old bulb by unscrewing it in an anti-clockwise direction.
Before Use
4. Replace with a new bulb (maximum 40w) by screwing it in a clockwise direction.
Make sure that it is secure in the bulb holder (your cooker hood is fitted with 2x 40w bulbs).
5. Replace the filters.
The Cooker hood is not working
Operation
• Check it is plugged in and switched on.
• Check that the fuse in the plug has not blown.
• Plug in another appliance, such as a lamp, to see if the socket is working.
Servicing
Specification
Cleaning, Maintenance
and Troubleshooting
Only an authorised, qualified technician should perform repairs and maintenance of the appliance.
GB-7
Satety Warnings
TECHNICAL SPECIFICATIONS
Model
LCH665SSELCH965SSE
Rated Voltage (V)230230
Rated Frequency (Hz)5050
Rated Power (W)200200
Weight (Kg)8.69.6
Product Dimension h/w/d (cm)
Before Use
Bulbs (E14)
18 x 60 x 50
19 x 90 x 50
2x40W max
2x40W max
Weight and Dimensions are approximate. Because we continually strive to improve our products we may change
specifications and designs without prior notice.
Operation
Cleaning, Maintenance
and Troubleshooting
Visit Partmaster.co.uk today for the easiest way to buy
electrical spares and accessories.
With over 1 million spares and accessories available we can deliver
direct to your door the very next day.
Visit www.partmaster.co.uk
or call 0870 6001 338
(UK customers only)
Calls charged at National Rate.
Specification
This symbol on the product or in the instructions means that your
electrical and electronic equipment should be disposed at the end of
its life separately from your household waste.
There are separate collection systems for recycling in the EU.
For more information, please contact the local authority
or your retailer where you purchased the product.
GB-8
Download PDF
Similar pages