W10677398B
NOTE
The manufacturer reserves the right for any modifications on the product which might
be deemed necessary or useful without informing about it in this IFU.
Thank you for choosing a Hisense washing machine.
Before operating your new washing machine, please read this instruction carefully,
ensure
and keep it for future reference.
Please make sure the socket is grounded securely, the water source connection is
reliable. The manufacturer declines all liability and warranty for damage to property or
injury to persons or animals due to non-compliance with the directions given in this
instruction.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
The new hose-sets supplied with the appliance are to be used and that old hose-sets
should not be reused.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical. Sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not
be conducted by children without supervision.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Ensure
Ensure that the ventilation openings in the base of the washing machine
(if available on your model) are not obstructed by a carpet or other material.
Children should be supervised to ensure that they do not play with the appliance.
The maximum permissible inlet water pressure, 1 MPa, for appliances intended to be
connected to the water mains
The minimum permissible inlet water pressure, 0.1 MPa, if this is necessary for the
correct operation of the appliance
Single inlet Dual inlet -
only
and cold
For washing machines with ventilation openings in the base, that a carpet must not
obstruct the openings.
1
2
that
ing
that
the
The symbol
on the product, or on the documents accompanying the product,
indicates that this appliance may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical
and electronic equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed information about
treatment, recovery and recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased
the product.
en
the
from the mains supply,
,
3
4
Clean the outside of the washing machine with a damp cloth. Do not use abrasive
detergents.
Never open the door forcibly or use it as a step.
3 Pour a little detergent (about 30 ml) into the main wash chamber
2
4
3
5
gent dispenser .
4. Select and start a short programme (see separate quick reference guide).
PREPARATION OF THE WASHING
Type of fabric / care label symbol
7
Cottons, mixed fibres, easy care/synthetics, wool, handwash items.
Control panel layout and
appearance will depend on the model.
to be
of the deter-
1. Sort the laundry according to...
6
for
recommend that you carry out a short wash cycle without laundry.
2 Close the door.
1
can
To remove any residual water used during testing by the manufacture r, we
1 Open the tap.
DESCRIPTION OF THE WASHING MACHINE
while the
BEFORE THE FIRST WASH CYCLE
The wool wash cycle of this machine has been tested and approved by The
Woolmark Company for the washing of Woolmark garments labelled as “machine
wash” provided that the garments are washed according to the instructions on the
is
while the
for
is
garment label and those issued by the manufacturer of this washing machine.
Colour
Separate coloured and white items. Wash new coloured articles separately.
Loading
Wash items of different sizes in the same load to improve washing efficiency and
distribution in the drum.
Delicates
Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras)
in a cloth bag or pillow case with zip. Always remove curtain rings or wash curtains
with the rings inside a cotton bag.
2. Empty all pockets
Coins, safety pins etc. can damage your laundry as well as the appliance drum and
tub.
3. Fasteners
Close zips and fasten buttons or hooks; loose belts or ribbons should be tied
together.
Stain removal
Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the
programme.
5
6
.
/ soak
U
7
8
2
Depending on the model, Insert removal tool like
slotted screwdriver into the small opening of
bottom baffle, press the bottom baffle downward
with much strength and open it. Or, push down on
the tabs provided on both the sides and remove it.
unds
9
10
fit
fit
11
12
solv
and the power switched
ON
remove some
too
13
14
Hot / Cold fill fault - For Models with Dual Inlets
If you wish to connect hot and cold water supply (Fig.1):
1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red
filter on the rear side of machine.
2. Fix the other inlet hose to the cold water tap and to the inlet valve with the blue filter
on the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa).
If you wish to connect only the cold fill follow the below instructions (Fig. 2):
1. You will need a Y-piece connector. This can be purchased from local hardware or plumb
ing supplier.
2. Fix the Y-piece connector to the cold fill tap.
3. Connect the two inlet valves present on the rear part of the machine to the Y-piece
connector using the hoses provided.
Ensure that:
All connections are tightly fixed.
Do not allow children to operate, crawl on, be near or inside your washer.
Note that during the wash cycles, the surface temperature of the porthole door may
increase.
Close supervision of children is necessary when the appliance is used near children.
Hot fill
Y-piece
Red inlet valve
Red inlet valve
Blue inlet valve
Blue inlet valve
Fig.1
15
Cold fill
Cold fill
Fault Code List
Displayed on Display Window
Fault Description
“F01”
Water inflow fault
“F03”
Drainage fault
“F04”, “F05”, “F06”, “F07” “F23” and “F24”
Electronic module fault, overflow or too much foam.
“F13”
Door lock fault
“UNB”
Unbalance alarm
a. “F01” displayed on screen
The machine is not fed with water or insufficient water. Check:
• Faucet is fully open and has enough water pressure.
• Water inlet pipe is knotted or not.
• Filtering net of water inlet pipe is blocked or not (refer to maintenance and
repair).
• Water pipe is frozen or not.
Press “Start/Pause” key after fault is removed.
If fault occurs again, please contact with after-sale service (refer to after-sale
service.).
b. “F03” displayed on screen
The washer is not emptied. The washer stops the program being executed. Shut
down the machine and disconnect power supply. Check:
• Drain pipe is knotted or not.
• Filter in drain pump is blocked or not (refer to the cleaning of filter in drain pump)
Ensure that
Fig.2
16
C. Fault code
The washer stops when the program is running. The display window shows fault
code “F24”, fault codes from “F04’ to “F07”, “F13”, “F23” or “UNB”.
If fault code “F24” is shown
Water level reaches overflow level.
Remove it by pressing “Start/Pause” key and feed water.
Select and start required program. If fault occurs again, disconnect power supply
and contact with after-sale service.
If fault code “F04” to “F07”, “F23” shown
Electronic module fails.
Press “Power Supply” key for 3 sec to turn off the machine.
After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect
power supply and contact with after-sale service.
If fault code “F13” is shown
Door lock is abnormal. Start program for 20 sec and unlock the washer door
(PTC) to check whether the door is closed.
adequate for the machine’s 10 A Current Rating.
Open or close it again.
After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect
power supply and contact with after-sale service.
The electrical power cable must be replaced exclusively by a licensed electrician.
If fault code “UNB” is shown
Unbalance alarm.
Press “Power Supply” key for 3 sec to turn off the machine. Open the door and
re-tidy clothes and then rotate program knob to single dehydration mode. Spin
clothes to dry again.
If fault occurs again, disconnect power supply and contact with after-sale service.
17
18
Download PDF
Similar pages