Instruction Manual Sun Pop® Select and

Instruction Manual
®
Sun Pop Select
and SunnyPop
TM
Model No. 2552-00-010 and 2552-00-012
Sun Pop Select
Model 2552-00-010
SunnyPop
Model 2552-00-012
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
© 2015 Gold Medal Products Co.
Part No. 110113
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
To avoid burns, DO NOT touch the kettle or any heated surface.
DO NOT place or leave objects in contact with heated surfaces.
013_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
Page 2
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This
information may not be the latest available for your purposes. It is critical that
you call Gold Medal’s Technical Service Department at 1-800-543-0862 for any
questions about your machine operations, replacement parts, or any service
questions. (Gold Medal Products Co. does not assume any liability for injury due
to careless handling and/or reckless operation of this equipment.)
Page 3
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
Sun Pop Select Model:
2552-00-010: 12 oz. Popper with a Sun Pop Select LED lighted sign, and equipped with a
PowerOffTM Control feature.
SunnyPop Model:
2552-00-012: 12 oz. Popper with a SunnyPop LED lighted sign, and equipped with a
PowerOffTM Control feature.
Items Included with this Unit
Aluminum
Scoop
Measure
14.7 cc
Knobs with Tee Bolts
(for Popper Doors)
Measure
1/2 Cup
Knob with Screw
(for Old Maid Pan)
Page 4
12 oz. Corn
Measure
Bulb for Cabinet
Interior
Black Crutch Tips
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation.
2. Place the unit on a sturdy, level base.
3. The Popper must be installed with a minimum 6” clearance
4. The popper unit has 4 glide feet preinstalled at the factory (reference image shown).
Install a Black Crutch Tip on each of the 4 glide feet. Firmly push the crutch tip over
the glide until it covers the glide entirely.
5. Door knobs are shipped in the accessories pack located inside the machine. Install a
door knob with tee bolt on each popper door (insert tee bolt from interior side of
door, then fasten knob on exterior side).
6. Install the knob with screw on the old maid pan.
7. Carefully install the light bulb (do not over-tighten) into the lamp holder located in the
cabinet interior. Ensure the unit is OFF and unplugged before installing or changing
the bulb (reference the Electrical Requirements section).
Glide (pre-installed
at the factory)
Black Crutch Tip
General image shown for reference.
Page 5
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Electrical Requirements
The following power supply must be provided:
2552-00-010, 2552-00-012: 120 V~, 1400 W, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are in the OFF position before plugging the equipment
into the receptacle.
2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the
power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install the unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
Page 6
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
OPERATING INSTRUCTIONS
Controls and Their Functions
KETTLE HEAT SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the heating elements in the
popping kettle. The green switch light ON indicates there is power to the kettle heating
element.
KETTLE MOTOR SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the kettle agitator motor.
The Kettle Motor Switch MUST be ON at all times when there is popcorn (popped or unpopped) in the kettle. The green switch light ON indicates there is power to the agitator
motor.
LIGHTS/WARMER SWITCH
Two position, ON/OFF lighted rocker switch - supplies power to the popcorn sign, interior
cabinet light, and heat element for the corn pan.
Label used on units with the
PowerOff Control feature.
Lights/Warmer
Switch
Kettle Motor Switch
Kettle Heat Switch
POWEROFF CONTROL
The PowerOff Control feature will automatically turn the kettle heat off after 15 minutes of idle
time (no popcorn popped). The PowerOff Control will prevent the heat element and thermostat
from cycling OFF-ON if the Kettle Heat Switch is left on. This feature saves electrical power and
extends the life of the kettle heating element and thermostat.
•
When the Kettle Heat Switch is turned ON, and the kettle thermostat switches OFF,
the PowerOff Control’s 15 minute timer starts; the 15 minute timer resets each
time a batch of popcorn is popped.
•
The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate
the kettle has been automatically turned OFF.
•
To restart the kettle heating, cycle the Kettle Heat Switch OFF-ON.
Page 7
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Popping Corn
This section describes instructions for popping Standard (salted popcorn).
Amount of Popcorn and Oil
Your new popper is equipped with a corn, salt, and oil measure. We recommend flavored and
colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black
deposits in your kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.
Ingredient amounts for popping Standard Popcorn:
Kettle Size
12 oz.
Popcorn Charge
12 oz. (355 ml)
Oil Charge
4 oz. (118 ml)
Flavacol (Salt)
1 Tblsp. (15cc)
For best results use Mega-Pop® 12 oz. premeasured pouches (Item# 2839).
Popping Standard (Salted) Popcorn
1. Turn the Lights/Warmer, Kettle Heat and Kettle Motor Switches ON.
2. To determine when the kettle is ready to pop corn (about 4 minutes), test pop three
kernels of corn and one ounce (30 ml) of popping oil. When the kernels pop, the kettle
is ready for use.
3. Lift the kettle lid and load the Mega-Pop® premeasured popcorn and oil pouch into
kettle, or pour in the popcorn and Flavacol, then add oil in the premeasured amounts
specified above. Close lid.
4. When the corn has finished popping, gently dump the popcorn.
5. On the final kettle of corn, turn the Kettle Heat Switch OFF just as the lids are forced
open by the popping corn. This procedure saves electricity, since the kettle has plenty
of heat, and helps eliminate smoke/odor from any oil residue that remains after
popping has stopped.
6. When finished popping, make sure KETTLE HEAT and KETTLE MOTOR switches are
turned OFF.
NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN!
If Auto Shut-OFF is enabled, unit will automatically shut kettle heat OFF after 15
minutes of idle time (no popcorn popped). To restart kettle heating, cycle the Heat
Switch OFF-ON.
Page 8
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water.
Always unplug the equipment before cleaning or servicing.
025_020314
WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!
028_082715
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Note: It is extremely important to follow all of the cleaning procedures, otherwise parts
damage and equipment failure will result. The warranty does not cover parts that
are damaged due to improper cleaning.
Daily Kettle Cleaning Instructions
CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool
at least 1 hour before attempting to clean. DO NOT use ice or water to cool
down a hot kettle! Severe kettle damage will result!
1. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven
cleaners or abrasive materials as they will damage the kettle.
2. Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons
per gallon of water. It is not necessary to use the entire gallon at once; only use
enough to fill the kettle 1/2 inch deep.
3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF.
4. Allow to cool for at least 1 hour, then dump the solution into a bucket and wipe the
inside of the kettle with a clean cloth. Make sure all of the solution goes into the
bucket; do not spill any in the interior of the machine.
For extra dirty kettles, the process may be repeated; or, after turning the kettle heat
OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution
into a bucket and wipe the inside of the kettle with a clean cloth.
5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp
cloth. DO NOT get moisture into the kettle lead-in cord, severe damage will result.
Page 9
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Daily Unit Cleaning Instructions
1. With the machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. Make sure to clean all pans/accessories in order to sanitize them before each use.
3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from the glass and cabinet.
4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of the
machine.
5. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item
No. 2588) is recommended.
Ammonia cleaners will damage the plastic doors. Use only non-ammonia cleaners,
such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).
Page 10
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Filter Cleaning Instructions
Your popcorn machine is equipped with an efficient and durable filtration system. The filter
should be cleaned every 1-2 weeks to maintain maximum efficiency.
Follow the steps below for proper filter cleaning:
Step 1: The filter is located on the
inside of the popcorn machine
directly above the popping kettle.
Step 2: Remove the filter by
gripping the filter itself and pulling
straight down.
Step 3: Clean the filter in warm
soapy water, then rinse and allow to
dry overnight. Replace the filter by
putting it into the slot and pushing
upward. Make sure the filter frame
is flush with the roof of the machine
(as shown above).
Page 11
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Troubleshooting
Issue
Possible Cause
Solution
Kettle Does Not Heat
A. Power to Unit
A. Make sure the lead-in cord is plugged in.
B. Power to the Kettle
B. Make sure the kettle lead-in cord is plugged in.
C. Kettle Heat Switch
C. Have a qualified service person check the
voltage to and from the Kettle Heat Switch; if
switch is defective, replace it.
D. PowerOff Control
D. Units with the PowerOff Control feature, kettle
heat will automatically shut OFF after 15
minutes of idle time (no popcorn popped).
The small green neon light in the Kettle Heat
Switch will blink OFF-ON to indicate the kettle
has been automatically turned OFF.
To restart kettle heating, cycle the Heat Switch
OFF-ON. Reference the Controls and Their
Functions section of this manual.
Long Popping Cycles
(Longer than 4 minutes for
Salt Popcorn)
E. Heating Element
E. Heating element in the kettle may be burned
out. Check with a qualified service person for
inspection/repair.
A. Low Voltage
A. If the machine is operated on low voltage, this
could cause the kettle not to reach the proper
operating temperature. Voltage with kettle
turned on, should be at least 112 V. Check with
a qualified electrician.
The use of extension cords is not
recommended due to safety concerns, and
may cause sacrificed and/or reduced
performance. If the use of an extension cord
cannot be avoided then be sure it is no longer
than 10 to 12 ft., and is at least 14 AWG wire.
B. Inadequate Supply Lines
B. Inadequately sized electrical supply lines, in
addition to being a fire hazard, would also
prevent the kettle from reaching the proper
operating temperature. Check with a qualified
electrician.
C. Inferior Corn
C. Inferior quality corn would result in longer
popping cycles. Use only top quality hybrid
popcorn from reputable suppliers. Even then,
if you let your corn pick up moisture or dry
out, your popping cycles will be slow.
Page 12
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Issue
Possible Cause
Solution
Kettle Agitator Shaft not
Rotating
A. Kettle Motor Switch
A. If the kettle agitator shaft is not rotating,
DO NOT pop corn. Make sure the Kettle Motor
Switch is ON. If the switch is ON, and the shaft
is not rotating, the switch or motor may be
faulty, contact qualified service personnel for
inspection/repair.
B. Kettle Agitator Shaft/Stir
Blade not rotating. (Unit
must be OFF, unplugged
and cool prior to
checking or adjusting
the agitator assembly.)
B. If the kettle agitator shaft is not rotating,
DO NOT pop corn. Check the clearance
between the kettle bottom and the stir blade;
it should be 1/32” (use a dime). To adjust,
loosen the set screw in the collars above and
below the crossbar and adjust the agitator
shaft as necessary. Then re-tighten the set
screws in the collars.
Page 13
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment will
void the warranty and may cause a dangerous condition. NEVER make
alterations to this equipment. Read the Installation, Operating, and
Maintenance Instructions thoroughly before installing, servicing, or operating
this equipment.
014_051514
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914
Page 14
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list.
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: (800) 543-0862
(513) 769-7676
Fax:
(800) 542-1496
(513) 769-8500
E-mail: info@gmpopcorn.com
Web Page: gmpopcorn.com
Page 15
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be
obtained from a local glass shop and always purchase tempered glass.
1. Remove all loose pieces of glass.
2. Pull out magnetic clip to remove (clip located above glass panel in cabinet interior).
3. Remove all rigid glass channels from around the glass to be replaced. Set it aside as it
must be reused.
4. Carefully remove the rest of the broken glass.
5. Apply decals (if desired) to the new glass panel.
6. Slide rigid glass channels over the exposed sides and bottom of new glass panel.
7. Carefully slide glass panel up under top ridge, then lower into the bottom channel.
8. Reinstall magnetic clip above the new panel in cabinet interior.
Magnetic
Clip
Remove magnetic clip
located above glass panel.
Slide glass panel up
under top ridge.
Lower glass panel into
bottom channel.
General images shown for glass installation reference only.
GLASS DIMENSIONS (Height X Width X Thickness)
Front and Side Glass: 21 1/4” X 16 7/8” X 1/8” (3 Pieces)
Page 16
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
12/14 oz. Kettle Assembly – 58014 - Parts Breakdown
Images K ettle ( 61 054 EX) A gitator ( 56 000)
Complete Agitator Assembly
(Includes Lids)
1
9
1
2
10
11
8
12
3
6
4
13
5
14
15*
16
6
28
7
* See Parts
List note.
17
27
18, 16
26
25
20
24
19
Complete Agitator Assembly
(Includes Lids)
23
22
Element/Heater View
21
Complete Kettle Bottom Assembly includes
Kettle Shell and Kettle Lead Assembly
Page 17
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
12/14 oz. Kettle Assembly – 58014 - Parts List
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Part Description
1/4-20 X 1/2 THUMB SCREW
8-32X1/2 FL HD PH MS
SHELL & KETTLE BLOCK
KETTLE SHELL
KETTLE LEAD ASSY
DUMP HANDLE-BLOCK WELD
DUMP HANDLE KNOB
8-32X1 FL HD PH MS
LID & AGITATOR ASSY (Complete Assembly)
KETTLE CROSSBAR ASSEMBLY
FORMED LID
REAR KETTLE LID
AGITATOR BEARING HUB
NEEDLE BEARING
SPUR GEAR KIT (Includes 2 gears with set
screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.)
SET SCREW #10-32 X 3/16
12/14 OZ. AGITATOR SHAFT
SET COLLAR 5/16 ID 5/8 OD
AGITATOR WEIGHT
POP MAXX STIR ROD
Part No.
58014
61059
20066
61013
61017
61226
88769
47110
20068
58016
58015
47261
47119
43434
47106
47059K
41742
69712
46649
69715
69806
Kettle Bottom Assembly – Element View
21
22
23
24
25
26
27
28
12/14 OZ. KETTLE BOTTOM ASSEMBLY
(includes Kettle Shell, Kettle Lead Assembly and
items listed below.)
8 OZ. KETTLE GASKET
KETTLE INTEGRAL HTR 12/14
482°F THERMOSTAT
(two 6-32 X 3/16 screws included)
550°F THERMOSTAT
(two 6-32 X 3/16 screws included)
8-32 TOP LOCK NUT (used to hold Thermostats
and ground – replace lock nut if removed)
THERMOSTAT SHUNT BAR
SHUNT BAR
Page 18
58012
61012
58011
76708
77108
67943
47193
77879
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Cabinet Exterior – Front View
2387- 00- 010
1
2
4
See Lighted
Sign Section
3
For Glass Panels,
see Replacing
Glass section.
See Kettle
Assembly
Section
5, 6
7
General image shown for parts reference only.
Item
1
2
3
4
5
6
7
Part Description
8-32 X 3/8 SLT. HWH M/S
DOME WELDMENT
21 5/16” GLASS CHANNNEL (used on the side
edges of the glass panels)
16 1/4” GLASS CHANNEL (used on the top and
bottom edges of the glass panels)
GLIDE
10-24 X 3/4” HEX HEAD
CRUTCH TIP BLACK 70 DURO
Page 19
Part No.
42044
111417
49844
74172
47328
41314
49123
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Cabinet Exterior – Rear View
2387- 00- 010
**Complete Door Hardware Kit
(See next page for individual
component breakdown).
1, 2
3
4**
6
5**
7
For Labels, See
Safety Labels
Section
8
12
9
13*
10, 11
* CAUTION: If supply cord is damaged, it must be replaced
by Gold Medal Products Co., its service agent, or similarly
qualified persons in order to avoid a hazard.
General image shown
for parts reference only.
Item
Part Description
Part No.
1
2
3
4**
5**
MAGNETIC CATCH
MAGNETIC CATCH BRACKET
MACNETIC BRACKET SHIM
COMPLETE LH DOOR HARDWARE KIT
COMPLETE RH DOOR HARDWARE KIT
8-32 X 1/2 PHIL PAN M/S (fastens male hinges to
the corner posts)
DOOR
DROP PANEL
OLD MAID PAN
LID LIFT KNOB
8-32” X 3/8” PH PAN W/SEMS
STRAIN RELIEF SR-7W-2
LEAD IN CORD 15 AMP PLUG
47561
41340
38527
47054
47055
6
7
8
9
10
11
13
12*
Page 20
47141
77774
77730
49100
47120
42227
67060
87085
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Door Hardware Kits – Individual Component Breakdown
1
3
2
4
2
3
5
Complete Right Hand Door
Hardware Kit (P/N 47055)
(contains all parts shown above)
Complete Left Hand Door
Hardware Kit (P/N 47054)
(contains all parts shown above)
Item
1
2
3
4
5
6
7
8
8
7
6
Part Number
47054
47055
Part Description
DOOR KNOB
8-32 X ½ SCREWS PH PAN W/SEMS
ACORN NUT #8-32
TEE BOLT
MALE HINGE SHORT LEFT
FEMALE HINGE LONG LEFT
FEMALE HINGE LONG RIGHT
MALE HINGE SHORT RIGHT
Page 21
41013
47124
47702
75267
41349
41352
41013
47124
47702
75267
41351
41350
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Cabinet Interior – Controls View
2387- 00- 010
6
1
5
2
3
4
14
13
11*, 12
7
Data
Plate
8
9
10
General image shown for parts reference only.
Item
1
2
3
4
5
6
7
8
9
10
11*
12
13
14
For Labels, see Safety Labels section.
Part Description
SMALL SWITCH BOX
SMALL SWITCH LABEL
GREEN LIGHTED ROCKER SWITCH
DPST ROCKER SWITCH
5 X 10 X 2 FILTER
FILTER SPRING CLIP
LED R20 LAMP 120V
.5x.5x.1 MAGNET GLASS LOCK
REAR HANGER ARM
FRONT HANGER ARM
SPUR GEAR KIT (includes 2 gears with set
screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.)
SET SCREW #10-32 X 3/16
GEAR BLOCK
L5-15R 15A RECEPTACLE
Page 22
Part No.
48501
48502
42798
42532
69850
62666
111493
51113
61050
61049
47059K
41742
67194
49330
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Cabinet Bottom – Corn Pan Element View
2552
* CAUTION: If supply cord is damaged, it
must be replaced by Gold Medal Products
Co., its service agent, or similarly qualified
persons in order to avoid a hazard.
1*
2
See Labels
3
4
5
6, 7
General image shown for parts reference only.
Item
1
2
3
4
5
6
7
Part Description
LEAD IN CORD 15 AMP PLUG
STRAIN RELIEF
120 VOLT FOIL HEATER
.875 SNAP BUSHING
BOTTOM COVER
GLIDE
10-24 X 3/4 HEX HD
Page 23
Part No.
87085
67060
40557
45396
49838
47328
41314
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Motor Plate Assembly
Male Cordset shown
(see Lighted Sign Assy. for Female Cordset)
15
14
13
12
1
10, 11
2
9
8
3
4
7
2552-00-010 Image Shown.
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
See Controls View
Part Description
LIGHT SHIELD CONICAL
LAMP HOLDER
BLOWER PLUG AND CORD
EXHAUST BLOWER
BUSHING, SNAP .625 IN
KETTLE RECEPTACLE
TERMINAL BLOCK
120 VOLT KETTLE DRIVE MOTOR
SHUT OFF CONTROL PCB
6-32 X 3/8 PHIL PAN M/S
#6 INTERNAL TOOTH L/W 410SS
BUSHING, SNAP .500 IN
SHUT OFF BRACKET
BUSHING, SNAP .875 IN
MALE CORDSET
Page 24
5
6
Part No.
40589
47047
47199
48018
47282
49330
47208
47038
55402
39000
39001
47236
111435
45396
61020
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Lighted Sign Assembly
Sun Pop Select Light Box Assembly
(111422) – Front View
1
2
3
4
5
6
7
Sunny Pop Light Box Assembly (111503) – Front View
8
9
10
11
12
15
Male Cordset
(not shown) is
included in Light
Box Assembly, see
Motor Plate Assy.
section for image
reference.
Light Box Assembly - Rear View
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
13, 14
Part Number
111422
111503
Part Description
SUN POP SIGN
SUNNY POP SIGN
LIGHT BOX FACE
LIGHT REFLECTOR
6-32 X 5/8 PAN PHILLIPS
LED STRIP COOL WHITE
BUSHING, SNAP .625 IN
MALE CORDSET
FEMALE CORDSET
STRAIN RELIEF SR-6P3-4
CORD BRACKET
POWER SUPPLY
6-32 X 1/2 PHIL PAN (Mounts Power Supply)
6-32 NUT (Mounts Power Supply)
8-32 PAN HD (Mounts the LED and Light Face)
Page 25
111420
111453
111451
77069
55379
47282
61020
61021
76026
111454
55394
42237
47517
74141
111483
111453
111451
77069
55379
47282
61020
61021
76026
111454
55394
42237
47517
74141
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Safety Labels
3
1
4
2
5
Unit Labels
6
Kettle Lead In Label
7
8
Power Cord Labels
Item
1
2
3
4
5
6
7
8
Part Description
COATED BULB LABEL
UNIVERAL POPPER DECAL
MAIN GROUND LABEL
SURFACE CONTACT WARNING
POWER OFF LABEL
CONDUIT WARNING LABEL
CORD WARNING LABEL
POWER CORD TAG
Page 26
Part No.
42948
41019
42375
87087
55436
82840
68720
76135
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Accessories
1
2
Item
1
2
3
4
3
Part Description
STAMPED ALUMINUM SCOOP
14.7 CC MEASURE
1/2 CUP MEASURE
12 OZ CORN MEASURE
Page 27
4
Part No.
2071
47679
47149
47148
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
Wiring Diagram
Models 2552-00-010 and 2552-00-012
Page 28
gmpopcorn.com
Sun Pop Select
and SunnyPop
Model No. 2552-00-010 and 2552-00-012
WARRANTY
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
gmpopcorn.com
Phone: (800) 543-0862
(513) 769-7676
Fax: (800) 542-1496
(513) 769-8500
© 2015 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
Page 29
gmpopcorn.com
Download PDF
Similar pages