Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
So…how do I use it?
CAUTION
Preprogrammed Times and Cook Level
To avoid fire, do not dry newspapers or clothes in
microwave oven.
Interrupting Operation
• Open oven door to interrupt operation. Oven
fan continues to operate. Close door and press
START pad to resume oven operation.
• Press STOP/RESET pad to interrupt operation.
Display continues to show countdown time.
Press START pad to resume oven operation
and countdown timing.
Canceling Mistakes
• If oven is operating, press STOP/RESET pad
once to stop oven, then again to clear
display.
• If oven door is open and time shows in
display, close oven door and press
STOP/RESET pad to clear display.
Operating Preprogrammed Pads
Oven had 10 ~ 20 preprogrammed number pads.
Instructions are written for factory programmed
ovens. Ovens that are reprogrammed can respond
QTY
2X
differently than described below.
1. Open oven door, place food in oven, and close
oven door
• If pad is not pressed in 30 seconds, open
and close oven door again.
2. Press desired number pad.
• Oven operates and time counts down.
3. Oven stops heating and oven signal sounds
when heating timing elapses.
Operating QTY 2X Pads
1. Press
Pad.
2. Press desired number pad.
• Example: press
Part No. 12869602
Revised 03/04
Pad = 18 sec.
All preprogrammed pads arrive set at full power.
Option: Single Digit
Heating
Pads
Times
Option: Double Digit
Heating
Heating
Times
Pads
Times
Pads
1
10 sec.
01
10 sec.
11
20 sec.
2
20 sec.
02
20 sec.
12
40 sec.
3
30 sec.
03
30 sec.
13
1 min.
4
45 sec.
04
45 sec.
14
1:30 min.
5
1 min.
05
1 min.
15
2 min.
6
1:30 min.
06
1:30 min.
16
3 min.
7
2 min.
07
2 min.
17
4 min.
8
3 min.
08
3 min.
18
6 min.
9
4 min.
09
4 min.
19
8 min.
0
5 min.
10
5 min.
20
10 min.
Manual Time Entry
Manual Time Entry feature allows the operator to enter
time and power levels, and heat without changing the
preprogrammed pads.
1. Open oven door, place food in oven, and close
door.
• Display shows “READY”.
• If pad is not pressed in 30 seconds, open and
close oven door again.
2. Press TIME ENTRY pad.
• Display shows “00:00”.
3. Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
press 2, 3, and 0 pads.
4. Press desired power level pad to change power
level.
• If a power level pad is not pressed, oven defaults
to 100% power.
• For example, pressing MEDIUM 50% pad sets
oven to 50% power.
• Display shows current power level if other than
100% power.
5. Press START pad.
• Oven operates and time counts down.
6. Oven stops heating and oven signal sounds when
heating time elapses.
For full product documentation visit:
www.amanacommercial.com/wavelink
© 2004 Amana Commercial
Amana, Iowa 52204
Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
So…how do I use it?
Preprogrammed Number Pads
Multiple Heating Stages
Oven has 10 ~ 20 preprogrammed number pads.
Follow instructions below to program heating times
and power levels for customized cooking.
1. Open oven door.
• If door is closed or RESET pad is pressed
before finishing programming sequence,
oven exits programming mode.
2. Press and hold pad 1 for approximately 5
seconds.
• After 5 seconds, signal sounds. Display
shows “PROGRAM” indicating program
mode.
3. Press desired number pad.
• Display shows heating time and
preprogrammed pad number.
4. Press number pads to enter desired cooking
time.
• For example, to heat for 2 minutes 30
seconds, press 2, 3, and 0 pads.
5. Press desired power level pad to change
power level.
• If a power level pad is not pressed, oven
defaults to 100% power.
• For example, pressing MEDIUM 50% pad
sets oven to 50% power.
• Display shows current power level if other
than 100% power.
6. Press START pad to save new heating time
and power level in oven memory.
• Repeat step 3-6 to program additional
pads.
7. Press RESET pad or close oven door to exit
programming mode.
Follow instructions below to program oven to
perform 3 consecutive heating cycles without
interruption.
1. Open oven door.
• If door is closed or RESET pad is pressed
before finishing programming sequence,
oven exits programming mode.
2. Press and hold pad 1 for approximately 5
seconds.
• After 5 seconds, signal sounds. Display
shows “PROGRAM” indicating program
mode.
3. Press desired number pad.
• Display shows heating time and
preprogrammed pad number.
4. Press number pads to enter desired cooking
time.
• For example, to heat for 2 minutes 30
seconds, press 2, 3, and 0 pads.
5. Press desired power level pad to change
power level.
• If a power level pad is not pressed, oven
defaults to 100% power.
• For example, pressing MEDIUM 50% pad
sets oven to 50% power.
• Display shows current power level if other
than 100% power.
6. Press TIME ENTRY pad.
• Display briefly shows “STAGE 2”. Then
cook time and power level for stage show
in display.
• Repeat steps 5-6 to create additional
stages.
7. Press START pad to save new heating time
and power level in oven memory.
8. Press RESET pad or close oven door to exit
Part No. 12869602
Revised 03/04
For full product documentation visit:
www.amanacommercial.com/wavelink
© 2004 Amana Commercial
Amana, Iowa 52204
Download PDF
Similar pages