Brillia INX26 SQB-700-2 Series Manual EN v 160101

KOBE Range Hood
Brillia Series
Model No. INX2630SQB-700-2
BRILLIA INX26 SERIES
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
IMPORTANT
READ THIS FIRST
READ BEFORE INSTALLATION
1. Carefully check all contents of packages.
2. Thoroughly inspect the unit for any shipping damages, cosmetic
damages or defects.
3. Have a certified contractor/electrician test the unit before installation.
IF THERE IS ANY PROBLEM:
1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL
PACKAGING MATERIAL.
2. Have your original invoice as proof of purchase and product serial
number ready.
3. Contact your merchant for product replacement due to shipping
damages, cosmetic damages or defects.
4. For all other issues, call 1-877-BUY-KOBE (289-5623), or e-mail to
info@koberangehoods.com .
NO RETURN, NO REFUND, NO EXCHANGE IF:
1. PRODUCT HAS BEEN INSTALLED
2. KNOCK-OUT HOLES HAVE BEEN PUNCTURED
3. MISSING ORIGINAL PACKAGING MATERIAL
AND/OR PARTS
[ENGLISH]
- READ AND SAVE THESE INSTRUCTIONS -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS.................................................................................... 1
COMPONENTS OF PACKAGE ................................................................................................. 3
INSTALLATION ......................................................................................................................... 4
OPERATING INSTRUCTIONS .................................................................................................. 9
MAINTENANCE ........................................................................................................................12
SPECIFICATIONS ....................................................................................................................13
MEASUREMENTS & DIAGRAMS.............................................................................................14
PARTS LIST .............................................................................................................................16
CIRCUIT DIAGRAM ..................................................................................................................18
TROUBLE SHOOTING .............................................................................................................19
WARRANTY .............................................................................................................................20
WARRANTY INFORMATION FORM ........................................................................................22
- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN
ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES
IMPORTANT SAFETY INSTRUCTIONS
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,
OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.
3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE
PANEL.
b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air properly,
make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl spaces or
garages.
NOTE
WARNING:
-
This warranty is void without an authorized agent’s receipt or if unit is
damaged due to misuse, poor installation, improper use, mistreatment,
negligence or any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried out without the
supervision of KOBE RANGE HOODS authorized agents will
automatically void the warranty.
-
KOBE RANGE HOODS will not be held responsible for any damages to
personal property or real estate or any bodily injuries whether caused
directly or indirectly by the range hood.
TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.
2. Always turn hood ON when cooking.
3. Use high settings on cooking range ONLY when necessary.
4. Do not leave cooking range unattended when cooking.
5. Always use cookware and utensils appropriate for the type and amount of food prepared.
6. Use this unit only in the manner intended by the manufacturer.
7. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.
8. Clean ventilating fan frequently.
1
What to Do In The Event Of a Range Top Grease Fire
•
•
•
•
SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go
out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.
NEVER PICK UP A BURNING PAN – You May Get Burned.
DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result.
Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
-
Extinguish any open flame.
Do not try to turn on the lights or any type of appliance.
Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and
Fire Department right away.
CAUTION
1. For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) to prevent back drafting.
3. Follow the heating equipment manufacturer’s guideline and safety standards such as those published
by the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4. Activating any switch on may cause ignition or an explosion.
5. Due to the size and weight of this hood, installation by 2 persons is recommended.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.
Disconnect appliance from electric power before servicing. If equipped,
the fluorescent light bulb contains small amounts of mercury, which must
be recycled or disposed of according to Local, State, and Federal Codes.
2
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
Range Hood Box
{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Quick Reference Guide
{D} Baffle Filter
{E} Oil Tunnel
{F} Stainless Steel Spacer
{G} Remote Control
{H} 6” Round Plastic Collar
{I} 3-1/4” x 10” Rectangular Exhaust
{J} Power Cord
{K} Twist-on Wire Connector
{L} Screw set
{H}
{I}
{J}
{K}
{A}
Adjustable Liner (Sold Separately)
Model No. INL36252B
{L}
{M} Front Section of Liner
{N} Rear Section of Liner
{M}
{B}
{C}
{N}
{D}
{F}
{E}
{G}
(AAA Batteries not
-
FOR MORE INFORMATION, PLEASE VISIT OUR W EBSITE www.koberangehoods.com OR CONTACT
KOBE RANGE HOODS AT (626) 775-8880.
3
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
To calculate installation, please refer to TABLE 1. (All calculation in inches.)
- FOR UNDER THE CABINET -
TABLE 1
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36")
C = Height of Counter Top to Wood Frame
Bottom (Minimum 26" to 30")
D = Height of Wood Frame
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING
ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY
OCCUR.
4
Figure 1
Preparation Before Installation
NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS
FROM ENTERING THE VENT OPENING.
• Decide the location of the venting pipe from the hood to the
outside. Refer to Figure 1.
• A straight, short vent run will allow the hood to perform more
efficiently.
• Try to avoid as many transitions, elbows, and long run as
possible. This may reduce the performance of the hood.
• Temporarily wire the hood to test for proper operation before
installing.
• Important: Peel protective film off the hood, if any.
• Use duct tape to seal joints between pipe sections.
CAUTION:
If moving the cooking range is necessary to
install the hood, turn off the power in an electric range at
the main electrical box. SHUT OFF THE GAS BEFORE
MOVING A GAS RANGE. And use a protective covering to
protect cooktop and/or countertop from damage.
Figure 2
Custom Hood Preparation
1. The custom hood frame must be designed according to the
shape and the weight of the insert. Refer to Measurements
and Diagrams on Page 14-15.
2. A sturdy base (3/4 inch thick plywood recommended) is needed
to sustain the weight of insert.
3. If an optional liner will be installed, the side of the wood frame
must be sturdy (3/4 inch thick plywood recommended).
4. It is recommended to install front & rear stud support (not
included). Refer to Figure 2. For safety purposes, extra
installation holes on the side of the insert are provided.
Prepare the side stud support if needed.
5. Determine and mark the centerlines on the base of the wood
frame where the insert will be installed.
6. Determine the proper location for the Power Supply Cable.
Make a wiring access hole using a drill bit. Install the wire
cable and seal the gap around hole.
7. Cut out the opening where the insert will be installed. (Figure
3)
Figure 3
Liner Installation (Additional Purchase required)
8. The custom wood frame must have a sturdy base to
accommodate the cut-out for the insert. The base must be
recessed to accommodate the height of the liner (See liner
dimension on Page 15)
9. Secure the liner to the bottom of the base using screws (not
included) appropriate for the size and material of your wood
frame.
10. Liner is made up of two sections: a large, rear section with precut for insert and a front section for a total adjustable depth
between 23” and 25-3/4”.
11. Position the rear section of the liner so that it aligns with the back
edge of the custom wood frame. Use a pen to trace the outline
of the pre-cut area.
12. Install the rear section of the liner with 6 screws (not included).
13. Install the front section of the liner with 3 screws (not included)
5
Figure 4
Figure 5
Hood Preparation Before Installation
CAUTION:
If moving the cooking range is necessary to
install the hood, turn off the power in an electric range at
the main electrical box. SHUT OFF THE GAS BEFORE
MOVING A GAS RANGE.
14. Choose the required vent option. The Round Exhaust Plate is
pre-installed for top vent.
15. For Top 3-1/4” x 10” rectangular installation only:
Remove the pre-installed Round Exhaust Plate (Refer to
Figure 5). Keep screws to attach Rectangular Exhaust
Plate and Rectangular Exhaust Adapter.
Place Rectangular Exhaust Plate over vent and secure
with 2 screws (Refer to Figure 6). Place Rectangular
Exhaust Adapter over the Rectangular Exhaust plate and
secure with 10 screws (Refer to Figure 6).
Use remaining screws to secure exhaust plate.
For Rear Vent Options only:
NOTE: The blower is pre-installed for top vent. If
installing as rear vent, follow the steps below.
16. For Rear 6” round installation only:
Remove the Rear Round Vent Cover and Rear
Rectangular Vent Cover (Refer to Figure 4). Keep screws
to attach Round Exhaust Plate to rear vent.
Remove the pre-installed Round Exhaust Plate from top
vent (Refer to Figure 5). Attach it to the rear vent (Refer to
Figure 7) using the screws removed from vent covers.
Use the Round and Rectangular vent covers removed
from rear vent to seal top vent.
Remove the 4 screws that secure the blower system
(Refer to Figure 8). Hold the blower to keep it from
dropping as you remove screws. Keep screws to re-attach
blower. Slowly rotate blower system to align with mounting
holes at the back of the insert. Secure blower using 4
screws (Refer to Figure 9).
17. For Rear 3-1/4” x 10” rectangular installation only:
Remove the Rear Round Vent Cover and Rear
Rectangular Vent Cover (Refer to Figure 4). Keep screws
to attach Rectangular Exhaust Plate and Rectangular
Exhaust Adapter.
Place the Rectangular Exhaust Plate over vent and secure
with 2 screws (Refer to Figure 10). Place Rectangular
Exhaust Adapter over the Rectangular Exhaust Plate and
secure with 10 screws (Refer to Figure 10).
Use remaining screws to secure exhaust plate.
Remove the pre-installed Round Exhaust Plate from top
vent and keep screws (Refer to Figure 4). Use the Round
and Rectangular vent covers removed from rear to seal top
vent.
Remove the 4 screws that secure the blower system
(Refer to Figure 8). Hold the blower to keep it from
dropping as you remove screws. Keep screws to re-attach
blower. Slowly rotate blower system to align with mounting
holes at the back of the insert. Secure the blower using 4
screws (Refer to Figure 9).
6
Figure 6
Figure 7
Figure 8
Figure 9
Duct Work Installation
18. Determine and make all necessary cuts in the wall or ceiling for
the ductwork. Note: Install the ductwork before installing the
insert.
19. Use steel pipe to connect the exhaust on the hood to the
ductwork above. Use duct tape to make all joints secure and
air tight.
20. Please refer to local codes for the usage of a damper (not
included).
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE
PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY
QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES.
BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM
BEING SWITCHED ON ACCIDENTALLY.
21. Connect electrical wires.
22. Connect three wires (black, white and green) to house wires
and cap with wire connectors. Connect wires according to their
colors (i.e. black to black, white to white, and green to green).
23. Store wires in the wiring box.
Hood Installation
Figure 10
Figure 11
NOTE: USE HAND TOOLS ONLY. DO NOT OVER TIGHTEN
SCREWS. IT MIGHT CAUSED DAMAGED TO THE HOOD.
24. Remove 10 screws located at the bottom of the insert (Refer to
Figure 11). Carefully remove the light support panel.
25. Position the insert inside the custom wood frame, and secure the
insert to the front and rear stud support ( Refer to Figure 2) by
using the front and rear mounting holes (Screws not included).
26. For a more secure installation, use the mounting holes located
on the side of the insert
27. Make sure insert is secure before releasing.
28. Re-install the light support panel. (Do not over tighten screws.)
CAUTION:
MAKE SURE HOOD IS SECURE BEFORE
RELEASING.
7
Figure 12
Figure 13
Final Assembly
29. Install the oil tunnel into recess support near rear of hood.
Refer to Figure 12.
30. Install baffle filters. Angle baffle filter toward back of hood ①
. Push baffle filter up until almost level ②. Slide forward into
recess behind the front of hood ③. Lower baffle filter ④. Slide
back until it fits into resting position ⑤. Refer to Figure 13.
8
OPERATING INSTRUCTIONS
This KOBE hood is equipped with five electronic push buttons with LED display, a wireless remote control, a double
horizontal squirrel cage blower with stainless steel baffle filters and two bright LED lights.
The five control buttons are Power Control (On/Off & 3-Minute Delay Shut-Off), Speed Control (High, Medium, Low &
QuietMode™), ECO Control, Timer Control and Light Control. Refer to Figure 14.
Figure 14
Delay
Shut-OffControl
Delay
Shut-Off
Note: For best results, turn the range hood to QuietMode™ prior to any preparation or cooking. Adjust speed as
needed.
Power Control
Press Power Control to turn On/Off the range hood. Hood will power on at Low speed.
Output Display:
3-Minute Delay Shut-Off Control
Delay Shut-Off Control powers down the range hood after 3 minutes. Press the Power Control to activate
Delay-Shut off. The Timer Indicator will automatically begin to count down from the default 3 minutes. When
the time is up, the unit will completely power off.
To bypass the 3-Minute Delay Shut-Off, press the Power Control again to completely power down the unit.
9
Speed Control
(Each press of Speed Control will cycle the fan through Low, Medium, High and QuietMode™.)
Output Display will indicate:
= QuietMode™ Speed
= Low Speed
= Medium Speed
= High Speed
ECO Control
The ECO function is set to turn on the range hood on QuietMode™ setting for 10 minutes every hour
to remove excess moisture, microscopic particles and odors for better kitchen air quality.
ECO is independent from the power function.
To activate ECO when the unit is powered off, press the ECO Control. The ECO icon will be displayed
to show that it is active. To deactivate it, press the ECO Control again. The icon will turn off, indicating
it has been deactivated.
To activate ECO when the unit is powered on, press the ECO Control. The ECO icon will be displayed
to show that it has been activated. In order for ECO to take effect, the unit must be turned off. If
the fan is running, power it off by pressing the Power Control. The unit will automatically shut down in
3 minutes. To power down immediately, Press the Power Control again to power down the unit. Once
the unit is powered off, the ECO icon will remain displayed, indicating that it is active. To deactivate it,
press the ECO Control again. The icon will turn off, indicating it has been deactivated.
NOTE: Must open door or windows to create sufficient make-up air when ECO is operating.
Output Display when ECO is active:
Light Control
(Lights are controlled independently from Power Control. Turning the power off will not turn the lights off.)
Press Light Control to turn lights ON. Press Light Control again to DIM the lights. Press Light Control
again to turn lights OFF.
Timer Control
The Timer Control allows users to set their range hood to automatically turn off. The timer ranges from 1
min. to 99 mins.
To activate the timer, the fan must be on (High, Medium, Low, or QuietMode™). As the fan is running,
toggle the timer by pressing the Timer Control. The Timer Indicator will flash, indicating it is ready to be set.
Press the Timer Control to set desired time, starting from 1 min. up to 99 mins. When finished setting time,
the timer will begin to automatically count down.
10
Baffle Change Indicator
The display
will indicate when baffle filter needs cleaning. Press and hold the Power Control for 5
seconds to reset the Baffle Change Indicator.
Remote Control
The six control buttons for the wireless remote control are Power Control (On/Off & 3 Minute Delay Shut-Off), Light Control,
ECO Control, Timer Switch Control and Speed Controls (High, Medium, Low & QuietMode™).
NOTE: Requires 2 AAA Batteries. Batteries not included.
Power Control
Press Power Control to turn hood ON and OFF. Hood will power on at Low speed.
3-Minute Delay Shut-Off Control
Delay Shut-Off Control powers down the range hood after 3 minutes. Press the Power Control to activate
Delay-Shut off. The Timer Indicator will automatically begin to count down from the default 3 minute setting.
When the time is up, the unit will completely power down. To bypass the 3 minute Delay Shut-Off, press
the Power Control again to completely power off the unit.
Light Control
(Lights are controlled independently from Power Control. Turning the power off will not turn the lights off.)
Press Light Control to turn lights ON. Press Light Control again to DIM the lights. Press Light Control
again to turn OFF lights.
Speed Control
Press the Speed Control to activate the fan. The fan will start on Low speed. Each press of the Speed
Control button will cycle through the various speeds.
Press
to cycle from High, Medium, Low and QuietMode™
Press
to cycle from Low, Medium, High and QuietMode™.
Press Power Control to activate 3-Minute Delay
Timer Control
While the fan is running, press the Timer Control to activate the Timer. The Time Indicator will flash,
indicating it is ready to be set. Use the arrow keys to set the desired time.
Press of
will decrease the time by 1 minute. Each press of
will increase the time by 1 minute.
When finished setting desired time, the timer will automatically begin to count down or press the Timer
Control to immediately begin the countdown.
11
If the timer is not set (
and
OR
) within 6 seconds, the unit will automatically exit Timer Control Mode
arrow keys will return to speed function control.
ECO Control
To activate ECO when the unit is powered off, press the ECO Control. The ECO icon will be displayed
to show that it is active. To deactivate it, press the ECO Control again. The icon will turn off, indicating
it has been deactivated.
To activate ECO when the unit is powered on, press the ECO Control. The ECO icon will be displayed
to show that it has been activated. In order for ECO to take effect, the unit must be turned off. If
the fan is running, power it off by pressing the Power Control. Then press the Power Control again to
power down the unit. Once the unit is powered off, the ECO icon will remain displayed to indicate that
it is active. To deactivate it, press the ECO Control again. The icon will turn off, indicating it has been
deactivated.
MAINTENANCE
For optimal performance, clean the range hood surface and baffles regularly.
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of
the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the
stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood
finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use
dry soft towel to dry the hood.
3. DO NOT allow deposits to accumulate or remain on the hood.
4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
and cause rusting.
5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact
with stainless steel for extended periods. Many of these compounds contain chemicals, which
may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth.
To Clean Baffle Filter/Oil Tunnel
CAUTION: DRAIN OIL FROM BAFFLE FILTER, SPACERS & OIL TUNNEL REGULARLY TO
PREVENT OVERFLOW.
1. Remove all the baffle filters, spacers and oil tunnel.
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
CAUTION: SHARP EDGES
(Note: Baffle Filters are top rack dishwasher safe.)
12
SPECIFICATIONS
MODEL / SIZE
INX2630SQB-700-2
COLOR
Commercial Stainless Steel
CONSUMPTION / AMPERE
290W / 2.5A
VOLTAGE
120V 60Hz
NUMBER OF MOTORS
1
FAN TYPE: CENTRIFUGAL
Single Horizontal Squirrel Cage
EXHAUST
Top –
6” Round
3-1/4” x 10” Rectangular
Rear –
6” Round
3-1/4” x 10” Rectangular
CONTROLS
5 Push-Button with LED Display
- Timer Control
- 3-Minute Delay Shut-Off
- Wireless Remote Control
- ECO Control
LED Lights 3W x 2, Dual Level Lighting
LIGHTS
HOOD DIMENSION
(W X D X H)
30” x 18-1/2” x 12”
OPTIONAL ACCESSORIES
(W X D X H)
2 Piece Adjustable Liner
Model No.: INL36252B
(34-7/16” x 23”~25-3/4” x 3”)
HOOD WEIGHT (lbs)
INX2630SQB-700-2
Blower Air Capacity (cfm)
Net
Gross
42
52
QuietMode™
Low
Medium
High
300
420
590
750
1.0
2
5.0
6.0
Sone*
* One Sone is equivalent to 40 decibels.
**Specifications subject to change without notice.
13
MEASUREMENTS & DIAGRAMS
All ( ) are in millimeter.
All inch measurements are converted from millimeters. Inch measurements are estimated.
MODEL NO: INX2630SQB-700-2
Side View
Bottom View
Back View
Top View
14
Front View
Ajustable Stainless Steel Liner (Sold Separately)
Model No. INL36252B
15
PARTS LIST
MODEL NO: INX2630SQB-700-2
NO.
DESCRIPTION
MODEL/SIZE
PART NO.
1
Rectangular Exhaust Plate
L1-0241-0001B
2
Rectangular Vent Cover
L1-0241-0002A
3
Round Exhaust Plate
L1-0241-0001A
4
Rectangular Exhaust Adapter
L1-0241-0002B
5
Hood Casing
6
Electric Component Support
L1-0201-2630
7
Processor Board
L1-0404-2636-B
8
Capacitor x 1PCS
L1-0401-0120-10
9
Blower Bracket
L1-0233-2630
10
Oil Tunnel
11
Blower System
L1-0302-0120-802RE
12
Bottom Casing
B101-2630-09
13
Baffle Filter Support
B101-2630-15B
14
Stainless Steel Spacer {1-13/16”(46)x9-1/4”(235)
B101-2630-14B
15
Baffle Filter
B101-2630-15
16
Control Unit Support
L1-0207-2630
17
Control Unit
L1-0404-2636-A
18
Light Panel Support
B101-2630-06
19
LED Light (3W)
L1-0403-0301
INX2630SQB-700-2
INX2630SQB-700-2
10-2630B-700
B101-2630-14A
Optional Adjustable Liner (Sold Separately)
20
Rear Section of Liner
INL36252B
B103-2630-A
21
Front Section of Liner
INL36252B
B103-2630-B
16
MODEL NO: INX2630SQB-700-2
17
CIRCUIT DIAGRAM
MODEL NO.: INX2630SQB-700-2
18
TROUBLE SHOOTING
Issue
After Installation,
motor and lights
are not working.
Lights are
working, but
motor(s) is not.
Motor(s) is
working, but
light(s) is not.
The range hood
is vibrating.
Possible Cause
The power is not on.
The wire connection is not secure.
The control panel and processor board wiring
are disconnected.
The control panel and processor board is
defective.
Replace the control panel or processor board.
The motor(s) is defective.
The capacitor(s) is defective.
The control panel or processor board is
defective.
The LED light(s) is defective.
The LED light transformer is defective.
The control panel or processor board is
defective.
The blower system is not secure.
Replace the motor.
Replace capacitor(s).
Replace the control panel or processing board.
The turbine impeller/squirrel cage is not
balanced.
Hood is not secured in place.
The range hood
is not venting
out correctly.
home.
Replace the LED light.
Replace the LED light transformer.
Replace the control panel or processing board.
Tighten the turbine impeller/squirrel cage and air
chamber.
Replace the turbine impeller/squirrel cage.
Obstacle blocking the pipe work.
Check the installation of hood, tighten the mounting
bracket.
Adjust the clearance between the range hoods and
cook top to 27” to 30”. For Island range hood, the
clearance between the range hoods and cook top is
30” to 36”.
Open the window to enhance the performance of the
range hood by creating a sufficient make-up air.
Remove all obstacles from the duct work.
The pipe size is smaller than the
suggested pipe size.
The pipe connection is not properly sealed.
Change the ducting according to the manufacture
suggestion.
Check the pipe installation.
The damper is not properly installed or is
missing from the installation.
The damper is not installed.
Check the damper installation.
The range hood is installed outside of the
manufacture recommended clearance.
There is no make-up air inside the house.
Cold air is
coming into the
Solution
Make sure the circuit breaker and the unit’s power is ON.
Use a voltage meter to check the power supply.
Check and tighten wire connection.
Check wire continuity from control panel to processor
board.
19
By installing the damper, it will help to eliminate air
backflow.
WARRANTY
WARRANTY CERTIFICATE
KOBE Range Hoods (referred to herein as “we”or “us”) warrants to the original purchaser
(referred to herein as “you” or “your”) all products manufactured or supplied by us to be free from
defect in workmanship and materials as follows:
TWO-YEAR LIMITED WARRANTY FOR PARTS AND LABOR ON KOBE PREMIUM/BRILLIA
SERIES:
For two years from the date of your original invoice from a KOBE authorized dealer, we will, at
our sole discretion, choose to repair or replace the product free of charge that failed due to
manufacturing defects.
It is your sole responsibility to ensure the product is readily accessible for the service technician
to perform repairs. The service technician will not, under any circumstance, remove, alter
or modify any fixture built around and/or connected to the product to gain access to
perform repairs.
During the two-year Limited Warranty period, additional charges may apply which include but
are not limited to:
• Service technician travel charges if the requested service location is 30-miles out of
KOBE’s authorized service area
• Parts shipping expenses
• Un-installation of defective product and Installation of replacement product
Warranty Exclusions:
This warranty does not cover, including but not limited to the following:
a. Improper installation.
b. Any repair, alteration, modification not authorized by KOBE.
c. Duct alteration, modification and connection.
d. Incorrect electric current, voltage or wiring.
e. Normal maintenance and service required for the product.
f. Consumable parts such as light bulbs and carbon filters.
g. Improper usage of the product that it is not intended for, such as commercial use, outdoor
use and multi-family use.
h. Normal wear and tear.
i. Chips, scratches or dents by abuse or misuse of the product.
j. Damages caused by accident, fire, flood and other Acts of God.
k. Expenses incurred for service located outside of the designated service area.
l. Purchases from unauthorized dealers.
m. Removal fees of defective product and Installation fees associated with replacement
product.
20
If we determine that the warranty exclusions listed above apply or if you fail to provide all
necessary documentation for warranty service, you will be responsible for all expenses
associated with the requested service, including parts, labor, shipping, travelling and any other
expense related to the service request.
To qualify for warranty service, you must:
1. Have the ORIGINAL proof of purchase
2. Be the ORIGINAL purchaser of the product
3. Have the model number
4. Have the serial number
5. Have a description of the nature of any defect in the product or part
TO REQUEST WARRANTY SERVICE, PLEASE CONTACT THE KOBE RANGE HOODS
SERVICE CENTER:
KOBE SERVICE CENTER (USA ONLY)
Tel:
1-855-800-KOBE (5623)
E-mail: kobe@adcoservice.com
For service in Canada and to report a problem, please contact:
Phone: 1-626-775-8880
Email: customer.service@koberangehoods.com
21
WARRANTY INFORMATION FORM
Fill in the blanks and keep this paper with the original invoice in a
safe place for future service purpose.
1. Date of purchase
:
2. Model No.
:
3. Serial No.
:
For warranty service or spare parts purchase contact:
KOBE Service Center (USA ONLY)
Toll Free: 1-855-800-KOBE (5623)
Email: kobe@adcoservice.com
For service in Canada and to report a problem, please contact:
Phone: 1-626-775-8880
Email: customer.service@koberangehoods.com
Your notes:
22
KOBE Range Hoods
11775 Clark Street
Arcadia, CA 91006 USA
www.koberangehoods.com
This KOBE hood is made for use in the USA and CANADA only. We do not
recommend using this hood overseas as the power supply may not be compatible
and may violate the electrical code of that country. Using a KOBE hood overseas
is at your own risk and will void your warranty.
Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada
seulement. Il n’est pas recommandé d’utiliser cette hotte à l’étranger puisque
l’alimentation électrique pourrait ne pas être compatible et enfreindre le code de
l’électricité de ce pays. L’usage de la hotte KOBE à l’étranger est à votre propre
risque et la garantie sera annulée.
Esta campana de extracción KOBE ha sido fabricada para ser utilizada
únicamente en EE.UU. y CANADÁ. No recomendamos la utilización de esta
campana en el extranjero debido a que la fuente de energía podría no ser
compatible y podría violar el código eléctrico de dicho país. Utilizar una campana
KOBE en el extranjero será a su propio riesgo y anulará la garantía.
Ver. 160101
Information subject to change without notice.
Download PDF
Similar pages