The Benito
™
Ceiling Fan
Finishes: OB and SN
Net Weight 9.3 kg. (20.5 lbs.)
Model No. FP8003-220
OWNER'S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such
as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before
servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
6. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
7. Contact your local government for information regarding the collection systems available.
8. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the
food chain, damaging your health and well-being.
9. When replacing old appliances with new once, the retailer is legally obligated to take back your old applicance for disposal at least
for free of charge.
10. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have given supervision or instruction concerning use of the appliance by a person responsible
for their safety.
11. Children should be supervised to ensure that they do not play with the applicance.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan
must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. (fan and accessories not to exceed 50 lbs.
or 22.7 kgs.). See page 4 of owner’s manual for support requirements. Consult a qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 2.3 meter from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical
knowledge or experience, have your fan installed by licensed electrician.
6. Suitable for use with solid-state speed controls.
WARNING: To Reduce The Risk Of Electrical Shock, This Fan Must Be Installed With A General Use, Isolating Wall Control/Switch.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: The building installation must contain a device to disconnect all poles of the fan from the main supply. The contact distance
in all poles must be 3mm minimum.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during
the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned
to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to
defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser
will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we
will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,
tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of
heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan
or Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid
damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or
implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and
fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation
will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,
except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary
from state to state.
10. A certain amount of wobble is normal and should not be considered a problem or a defect.
Table of Contents
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .4
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .4
How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .5
How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .6
How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .7
How to Install Your Canopy Housing . . . . . . . . . . . . . . . . . . . .8
2
How to Assembly the Blades & Light Kit . . . . . . . . . . . . . . . . .9
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
How to Clean Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . .11
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Materials
Tools Needed for Assembly
• One Phillips head screwdriver
• One stepladder
• Three wire connectors (supplied)
• One wire stripper
• One 1/4” blade
screwdriver
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be a
3-conductor (2-wire with ground) of the following size:
Installed Wire Length
Up to 50 ft.
50-100 ft.
WARNING
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 4). If you
feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
Wire Size A.W.G.
14
12
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are
missing contact your local retailer.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check
mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should
you be interrupted.
• Fan Motor Assembly
• Hanger Bracket Assembly with
screws
• Downrod/Hanger Ball Assembly
• Ceiling Canopy
• Canopy Screw Cover Assembly
• Motor Coupling Cover Assembly
• Blade Arm Set
• Blade Set
• Light Plate-Upper Assembly
• Socket Plate Assembly
• Two G-50 Light Bulbs
• Lower Steel Cap Assembly
• Glass
• TR4WH-220V Remote Control
• Receiver Unit
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any
accessories designated specifically for use with this
product by Fanimation. Substitution of parts or
accessories not designated for use with this product
by Fanimation could result in personal injury or
property damage.
1. Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer to
exploded view illustration.
• Hardware bags:
– 3/16-24 x 7.5mm
(blade to blade holder)
Washer Head Screw
– 3/16” Fiber Washer
(blade to blade holder)
– 1/4”-20 x 14mm
(blade arm to motor)
Pan Head Screw
– Phillips Screwdriver, 4”
– Four Wire Connectors
– Balance Kit
FAN MOTOR
ASSEMBLY
HANGER
BRACKET
ASSEMBLY
W/SCREWS
DOWNROD/
HANGER BALL
ASSEMBLY
HARDWARE BAG
MOTOR
COUPLING
COVER
CANOPY
SCREW
COVER
ASSEMBLY
CEILING
CANOPY
LOWER STEEL
CAP ASSEMBLY
BLADE ARM SET
LIGHT PLATE
- UPPER ASSEMBLY
BLADE SET
RECEIVER
UNIT
SOCKET
PLATE
ASSEMBLY
GLASS
TWO 60-WATT
G-50
LIGHT BULBS
3
TR4WH-220
REMOTE
CONTROL
Energy Efficient Use of Ceiling Fans
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the
counterclockwise direction. The airflow produced by
the ceiling fan creates a wind-chill effect, making you
“feel” cooler. Select a fan speed that provides a
comfortable breeze, lower speeds consume less
energy.
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the
ceiling fan. Here are a few tips to ensure efficient
product performance.
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the
middle of the room and at least 2.3 M above the floor
and 18 inches from the walls. If ceiling height allows,
install the fan 8 - 9 feet above the floor for optimal
airflow. Consult your Fanimation Retailer for optional
mounting accessories.
Winter Season: Reverse the motor and operate the
ceiling fan at low speed in the clockwise direction.
This produces a gentle updraft, which forces warm air
near the ceiling down into the occupied space.
Remember to adjust your thermostat when using your
ceiling fan - additional energy and dollar savings
could be realized with this simple step!
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.
Electrical and Structural Requirements
Your new ceiling fan will require a grounded
electrical supply line of 220~240 volts AC, 50 Hz.The
outlet box must be securely anchored and capable
of withstanding a load of at least 35 lbs. Figure 1
depicts different structural configurations that may be
used for mounting the outlet box.
CEILING
WARNING
CEILING JOIST
To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
acceptable for fan support of 15.88 kg (35 lbs) or less.
Use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to
be replaced. Consult a qualified electrician if
in doubt.
2" x 4"
OUTLET BOX
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and
remove the existing light fixture.
Figure 1
WARNING
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
4
How to Assemble Your Ceiling Fan
1. Remove the hanger ball portion from the
downrod/hangerball assembly by loosening the set
screw in the hanger ball until the ball falls freely
down the downrod. Remove the pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 5
(Figure 1).
PIN
DOWNROD
SET SCREW
HANGER BALL
Figure 1
2. Loosen the two set screws in the downrod support.
Route blue, brown and orange lead wires through the
downrod (Figure 2).
BLUE, BROWN AND
ORANGE LEADS
DOWNROD
SET SCREWS AND
LOCKING NUTS (2)
Figure 2
3. Position downrod support and align the clevis pin
holes in both parts. Install the clevis pin and secure
with the hairpin clip. Tighten the two set screws
and locking nuts in the downrod support (Figure 3).
DOWNROD
SET SCREWS AND
LOCKING NUTS (2)
DOWNROD SUPPORT
HAIRPIN CLIP
CLEVIS PIN
SCREWDRIVER
Figure 3
4. Route wires through motor coupling cover, canopy
screw cover and canopy (Figure 4).
BLUE, BROWN &
ORANGE LEADS
CANOPY
CANOPY COVER
Figure 4
5. Reinstall the hanger ball on the downrod as
follows.Route the three 80-inch wires through the
hanger ball. Position the pin through the two holes
in the downrod and align the hanger ball so the pin
is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin.
Securely tighten the set screw in the hanger ball.
A loose set screw could create fan wobble
(Figure 5).
MOTOR COUPLING
COVER
GROOVE
PIN
CANOPY
HANGER BALL
DOWNROD
SET SCREW
Figure 5
5
How to Assemble Your Ceiling Fan (continued)
6. Cut off excess lead wire approximately 6 to 9
inches above top of the top of the downrod. Strip
insulation off 1/2-inch from the end of each lead
wire (Figure 6).
6 TO 9
INCHES
DOWNROD
NOTE: All set screws must be checked, and retightened
where necessary, before installation.
Figure 6
How to Hang Your Ceiling Fan
WARNING
To avoid possible fire or shock, be sure electricity is
turned off at the main fuse box before hanging.
CEILING
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advise, as it must be
grounded for safe operation.
NO
LESS THAN
2.3 M
WARNING
FLOOR
The fan must be hung with at least 2.3 M of clearance
from floor to blades (Figure 7).
Figure 7
1. Securely attach the hanger bracket to the outlet
box using the outlet box screws and washers
supplied with the outlet box (Figure 8).
OUTLET BOX
WARNING
The outlet box must be securely anchored. Hanger
bracket must seat firmly against outlet box. If the outlet
box is recessed, remove wall board until bracket
contacts box. If bracket and /or outlet box are not
securely attached, the fan could wobble or fall.
SCREW (2)
(Supplied with
Outlet Box)
TAB
Figure 8
2. Carefully lift the fan and seat the downrod/hanger
ball assembly on the hanger bracket that was just
attached to the outlet box. Be sure the groove in
the ball is lined up with tab on the hanger bracket
(Figure 9).
OUTLET BOX
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
Figure 9
To avoid possible shock, do not pinch wires between
the hanger ball assembly and the hanger bracket.
6
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a
licensed electrician.
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before hanging
(Figure 10).
MAIN FUSE BOX
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice, as
it must be grounded for safe operation.
Figure 10
NOTE: The hand-held remote included with this fan
has 16 different code combinations. To prevent
possible interference from or to other remote units,
simply change the combination code in your
transmitter and receiver.
REMOTE
CONTROL
DETAIL
1. To set the transmitter code, remove battery cover
by pressing firmly below arrow and sliding cover
off. Slide code switches to your choice of up or
down position. Factory setting is all up. Do not use
this position. With a small screwdriver or ball point
pen slide firmly up or down. Replace battery cover
on the transmitter (Figure 11).
9V/23A BATTERY
TRANSMITTER CODES
2. To set the receiver unit code, slide code switches
to the same positions as set on your transmitter
(Figure 12).
Figure 11
RECEIVER
UNIT
DETAIL
CODE SWITCHES
Figure 12
3. Slide the receiver unit into the open end of the
hanger bracket (Figure 13).
RECEIVER UNIT
HANGER BRACKET
Figure 13
4. Connect wires to terminal block as indicated:
Green hanger bracket and banger ball wires to
green/yellow (earth) wire. Brown receiver unit wire
(AC IN L) to red/brown live supply wire. Blue
receiver unit wire (AC IN N) to blue/black neutral
supply wire. Orange receiver unit wire (AC IN L1)
to orange for light.
Position all connected wires and receiver antenna
to allow installation of ceiling canopy. Using
canopy screws threaded into the hanger bracket
reinstal ceiling canopy. Restore electrical power
(Figure 14)
Terminal Block
on Bracket
GRN/YEL from hgr. ball
GRN/YEL from bracket
Brown to Motor
L
Orange to Light
L1
Blue
N
Green/Yellow
Fan Receiver
Wiring
Unit
BRN-To Motor L
ORG-For Light
BLUE-To Motor N
EARTH – Green/Yellow
BRNAC IN L
BLUEAC IN N
BLK-ANT
Figure 14
7
220VAC
Household
Supply
LIVE-Red/Brown
Orange
NEUTRALBlue/Black
How to Install Your Canopy Housing
1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw
without fully removing it. Assemble canopy by
rotating key slot in canopy over shoulder screw in
hanger bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw that
was previously removed (Figure 15).
CANOPY
SHOULDER
SCREWS (2)
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy
housing and not pinched between the housing and
the ceiling.
Figure 15
2. Securely attach and tighten the canopy screw
cover over the shoulder screws in the hanger
bracket utilizing the keyslot twist-lock feature
(Figure 16).
CANOPY COVER
Figure 16
8
How to Assemble the Blades and Light Kit
1. Position the blade over the blade holder with
threaded posts showing. Make sure the bottom
edge of the blade is fully seated against the blade
arm. With a Phillips screwdriver, tighten 3/16-24 x
7.5 mm washer head screws and fiber washers to
secure the blade to the blade arm (Figure 17).
3/16-24 x 7.5mm WASHER
HEAD SCREW AND FIBER
WASHER (3 each per blade)
CAUTION
BLADE
Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled
may result in damage to the fan blades.
BLADE HOLDER
Figure 17
HARDWARE USED:
3/16-24 x 7.5mm
WASHER HEAD
SCREWS
x 16
FIBER WASHER
x 16
2. Secure the blade holders to the motor support
using the 1/4-20 x 14 mm screws through the holes
located on the side of the motor support (Figure 18).
NOTE: Periodically check blade holder hardware and
resecure if necessary.
WARNING
BLADE HOLDER
1/2-20 x 14mm SCREWS
(2 per assembly)
To reduce the risk of personal injury, do not bend the
blade holders when installing, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between the rotating blades.
MOTOR SUPPORT
Figure 18
CAUTION
To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.
HARDWARE USED:
1/4-20 x 14mm
SCREWS
3. Remove one of the three screws in the support
bracket at the bottom of the motor assembly.
Slightly loosen the remaining two screws.
Assemble the light plate upper assembly to the
support bracket using the two key slots in the
socket plate. Replace the third screw and securely
tighten all three screws (Figure 19).
x 11
SCREWS (3)
MOTOR
ASSEMBLY
LIGHT PLATE
UPPER
ASSEMBLY
SUPPORT
BRACKET
Figure 19
9
How to Assemble the Blades and Light Kit (continued)
4. Connect the 2-pin connector from the socket plate
assembly to 2-pin connector from motor assembly
(Figure 20).
MOTOR ASSEMBLY
2-PIN CONNECTOR
SOCKET PLATE 2-PIN
CONNECTOR
SOCKET PLATE ASSEMBLY
Figure 20
5. Remove one of the three screws in the socket
plate assembly. Slightly loosen the remaining
two screws. Assemle the socket plate
assembly to the adapter plate assembly using
the two key slots. Replace the third screw and
securely tighten all three screws (Figure 21 ).
SCREWS (3)
ADAPTER PLATE
ASSEMBLY
SOCKET PLATE ASSEMBLY
Figure 21
6. Insert light bulbs into sockets (Figure 22 A).
6A. Don’t install the light bulbs if you want to install
the lower steel cap in Step 7A (Figure 22 B).
LIGHT
SOCKET
LIGHT BULBS (2)
Figure 22 A
LIGHT
SOCKET
Figure 22 B
7. Assemble the opal frosted glass to the adapter
plate assembly by twisting in a clockwise direction.
Do not over-tighten (Figure 23 A)
7A. Assemble the lower steel cap to the adapter plate
assembly by twisting in a clockwise direction.
(Figure 23 B).
LOWER
STEEL
CAP ASSEMBLY
OPAL
FROSTED
GLASS
Figure 23 A
10
Figure 23 B
How to Operate Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box (Figure 24).
WARNING
MAIN FUSE BOX
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until the blades are in place. Noise and
fan damage could result.
Figure 24
2. To make fan operational, install 12-volt 23 A battery
in hand-held remote transmitter, (if not using for
long periods of time, remove battery to prevent
damage to tran smi tt er) . St or e the remote away
from excessive heat or humidly (Figure 25).
Figure 25
3. If airflow is desired in the opposite direction, turn
the fan off and wait for the blades to stop turning.
Slide the coupling cover up to expose the reverse
switch. Then slide the reverse switch on top of
motor assembly to the opposite position and turn
fan on again (Figure 26).
COUPLING
COVER
Reverse Switch Information
Season
Rotation Direction
Switch Position
Summer
Winter
Counter-Clockwise
Clockwise
Left
Right
REVERSE
SWITCH
Figure 26
Maintenance
1. Periodic cleaning of your new ceiling fan is the only
maintenance that is needed. When cleaning, use
only a soft brush or lint free cloth to avoid
scratching the finish. Abrasive cleaning agents are
not required and should be avoided to prevent
damage to finish.
CAUTION
Do not use water when cleaning your ceiling fan.
It could damage the motor or the finish and create
the possibility of electrical shock.
How to Clean Your Ceiling Fan Blades
Periodic light dusting of the blades is recommended.
A feather duster will work best.
Avoid using water, cleansers, or harsh rags, which
can warp and ruin the finish.
11
Trouble Shooting
!
WARNING
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
Trouble
Probable Cause
1. Fuse or circuit breaker blown.
1.FAN WILL
NOT START
2. Loose power line connections to the
fan, or loose switch wire connections
in the switch housing.
3. Reversing switch in neutral position.
4. Dead battery in remote control.
1. Blades not attached to fan.
2. Loose screws in motor housing.
2.FAN SOUNDS NOISY
3. Screws securing fan blade holders to
motor flywheel are loose.
4. Wire connectors inside housing
rattling.
5. Motor noise caused by solid state
variable speed control.
6. Screws holding blades to blade
holders are loose.
7. Lower housing support set screw
loose.
1. Setscrew in downrod support is loose.
3.FAN WOBBLES
EXCESSIVELY
2. Setscrew in downrod/hanger ball
assembly is loose.
3. Screws securing fan blade holders to
motor hub are loose.
4. Blade holders not seated properly.
5. Hanger bracket and/or ceiling outlet
box is not securely fastened.
6. Fan blades out of balance.
Suggested Remedy
1. Check main and branch circuit fuses
or circuit breakers.
2. Check line wire connections to fan
and switch wire connections in the
switch housings.
CAUTION: Make sure main power is
turned off !
3. Make sure reversing switch position is
all the way to one side.
4. Replace with fresh battery.
1. Attach blades to fan before operating.
2. Check to make sure all screws in
motor housing are snug (not overtight).
3. Check to make sure the screws which
attach the fan blade holders to the
motor flywheel are tight.
4. Check to make sure wire connectors
in switch housing are not rattling
against each other or against the
interior wall of the switch housing.
CAUTION: Make sure main power is
turned off !
5. Some fan motors are sensitive to
signals from solid-state variable
speed controls. Solid-state controls
are not recommended, choose an
alternative control method.
6. Tighten screws securely.
7. Tighten set screw securely.
1. Tighten both setscrews securely in
downrod support.
2. Tighten the setscrew in the downrod/
hanger ball assembly.
3. Check to be sure screws which attach
the fan blade holders to the flywheel
are tight.
4. Check to be sure the fan blade
holders seat firmly and uniformly to
the surface of the motor housing.
If holders are seated incorrectly,
loosen the screws and retighten.
5. Tighten the hanger bracket screws to
the outlet box, and secure outlet box.
6. Balance blades using balance kit
provided in hardware bag.
1. If possible, consider using a longer
downrod. For example, use a 12”
downrod instead of the 4½” downrod
that comes with your fan.
4.NOT ENOUGH AIR
MOVEMENT
12
Parts List
Model No. FP8003**-220
Reference #
1
2
3
4
5
6
7
Description
Part #
9
10
11
Hanger Bracket Assembly w/Screws
Ball - Downrod Assembly (4.5)
Canopy
Canopy Screw Cover Assembly
Motor Coupling Cover Assembly
Fan Motor Assembly
Light Plate - Upper Assembly
Socket Plate Assemby (AP800309**)
Glass (P800308OP)
Light Bulb (60 Watt)
Blade Arm Set
Blade Set
12
13
14
Lower Steel Cap Assembly
Hand Held Remote Control
Receiver Unit
15
—
—
—
—
—
—
Bag Assembly, Loose Parts:
Wire Connector (4)
Washer Head Screw, 3/16-24 x 8 mm (16)
Fiber Washer, 3/16” (16)
Pan Head Screw 1/4-20 x 14mm (11)
4” Phillips Head Screwdriver
Balance Kit
8
AP255BL-220
ADR1-45**
PG155**
AP260**
APPAC1403**
AMA8003**-220
AP800306**
AP800311**
PPE14B60-220
AP800303**
AP800305**
AP800310**
TR4WH-220
RECAN1515-220
HDWFP8003**
—
—
—
—
—
—
** Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
•
•
•
Part Number
Part Description
Fan Model Number
Contact your retail store for repair parts.
13
FP8003**-220
Exploded-View
1
14
2
3
13
15
4
5
6
11
10
7
9
8
12
NOTE: The illustration shown is not to scale or its actual configurations may vary.
14
10983 Bennett Parkway
Zionsville, IN 46077
Toll Free (888) 567-2055
FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Fanimation Visit Our Website www.fanimation.com
Copyright 2010
2010/07
Download PDF
Similar pages