installation instructions

INSTALLATION INSTRUCTIONS
Option 1:
2 tap hole arch mixer with curved spout
(200mm centers)
-
Burlington has 4 different style handle for your selection.
T24
2 tap hole arch mixer with curved spout
(230mm centers)
-
T25
Anglesey
Claremont
Birkenhead Kensington
Option 2:
27mm
Burlington also have a base (27mm height) for your selection.
NOT INCLUDED IN THE TAP BOX
Important
● We recommend that this product is installed by a qualified professional contractor. Such as a plumber who is certified by NVQ
(National Vocational Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3
● Please check this product immediately to ensure that it has not been damaged and is complete. Before installation, please make
sure this product is the correct model and you have all the parts required for installation and using.
● All the taps in Burlington Range should be supplied with hot and cold water at balanced pressure. If not, then the mixing function
will not work correctly. It is necessary to fit non-return valves on both hot and cold feeds pipe. These are not supplied.
● Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the taps.
● Turn off water supply before commencing work, this should be done at the isolating valves of inlet feeds if fitted or main stopcock.
● Please read these instructions carefully and keep it for future reference.
Working pressure
The tap is suitable for both high and low pressure installation. To ensure that the tap works well under low water pressure, the
cold water storage tank must be at least 2 meters above the installed position. The maximum water pressure is 6 bar. Where the
water pressure above 6 bar, then a pressure reducing valve must be fitted.
Straightener and aerator (alternative option)
The tap comes with a factory-fitted flow straightener for low pressure water systems.
If the water flow is high, replace the factory-fitted flow straightener with the high pressure
aerator supplied.
Use NEOPERL Key to unscrew the straightener in the Nozzle. Replace with the aerator
provided, and screw back in nozzle tightly. (If you misplace the Neoperl key you can use
the top of the aerator/straightener as a key)
FLOW STRAIGHTENER
AERATOR
Cleaning
Before use: Unscrew the filter and allow the water to run freely for
5 minutes. Then screw the filter back in place.
NOZZLE
Periodically: Using the key provided unscrew the nozzle and remove.
Rinse it with cleaning running water until any loose debris is cleared.
Then replace the nozzle and tighten with key provided.
1-2
KEY
C
Dimension
200 (for T24)
230 (for T25)
103
Ø16
180°
16
Ø
80
102.5
99.3
162.8
0
Ø4
202.8
300.2
48.5
1
M24X
G3/4
Ø48
Installation
MIXER BODY
DECORATIVE
CAP
COLD
CONTROL
HANDLE
SCREW
SPRING WASHER
HOT
CONTROL
HANDLE
FLAT WASHER
NOZZLE
HANDLE
“O” RING
NOT INCLUDED IN THE TAP BOX
RUBBER
WASHER
Basin
Worksurface
FIXING
NUT
Note: To ensure the Kensington lever tap head
faces in the correct forward position once
installed, you may need to tighten the
cartridge into the tap body a notch with
a monkey spanner and then re-attach the
tap head.
A) Fit the “O” ring into the groove on the underside of the tap body.
B) Remove the rubber washer and fixing nut from the tail.
C) Insert both tails into tap holes on the basin.
D) Tighten the fixing nut from the under-side of the basin.
Maintenance
We do NOT recommend you use any household cleaners to clean the product. Because these cleaners change substance or formula
too frequently. The product should be always cleaned only with soapy water and rinsed with clean water and dried with a soft cloth.
2-2
C
Download PDF
Similar pages