LaneMinder 2.1.cdr - Cybernetic Solutions

Installation Notes:
by Cybernetic Solutions
Page 1 of 4
86 Barry Street
Reservoir
Victoria 3073
Australia
tenpintec
LaneMinder 2
Phone +61 3 9460 2559
Fax +61 3 9460 7071
tenpintec.com
Socket for 12VDC
Power Supply
LaneMinder 2
RESET
cancels all
PIN - Push Button for “pin in gutter”
timer (adjustable)
RESET
LANES
PIN
Disables LaneMinder and automatically
restarts after time delay.
POWER
Power ON
LANES - Push Button for lane
maintenance timer (adjustable)
Disables LaneMinder and automatically
restarts after time delay.
High Intensity
LED Array
Buzzer
RJ45 connector
for optional machine
or IR cut-out(s)
Regulated 12VDC required.
2.1mm DC socket
(centre pole
is positive)
REAR PANEL
ALARM LANE BEAM 2
Rx
PIN
BEAM 2 BEAM 1 BEAM 1 EXT CUTOUT
Rx
Tx
Tx
BUZZER
+
12VDC
-+
Adjuster for
ALARM time
Adjuster for
PIN time-out
Adjuster for
LANES time-out
RJ-45 connector for
BEAM 2 TRANSMITTER
RJ-45 connector for
BEAM 2 RECEIVER
RJ-45 connector for
BEAM 1 TRANSMITTER
RJ-45 connector for
BEAM 1 RECEIVER
12VDC signal
for optional
external alarm buzzer
Push Button
Switch
Press to shut off beam for 20 seconds
to enable staff to pass by without setting off alarm.
LED flashes during this time-out.
LANE
AREA
Receiver
BEAM 1
Mount Tx and Rx units between 5 and 15 feet
down the lane at a height of about 18 inches
(so lane machine will go under without
breaking the beam)
Transmitter
BEAM 1
BEAM 2 is optional
BEAM 2 works exactly the same as Beam 1 and is for bowling centres
with two lane zones (or a secondary area that needs an intrusion
detection alert).
BEAM 2 produces a different visible and audible warning from BEAM 1.
Receiver
BEAM 2
The Beam 2 option can be added at any time
- the standard LaneMinder 2 software automatically detects Beam 2
when it is plugged in.
Transmitter
BEAM 2
Installation
tenpintec
Mount IR Transmit and Receive modules on walls or posts at opposite ends of the LANE AREA
between 5 and 15 feet down the lanes at a height of about 18 inches to 2 feet above the
lane surface.
tenpintec.com
Situate the LaneMinder control box at the main reception counter or other suitable position.
Use supplied CAT-5 cables and joiners to connect the IR Transmit and Receive modules to the correct sockets on
the rear of the LaneMinder control box. (When only one beam is being used, connect to Beam 1).
Plug the 12VDC power supply into the rear of the LaneMinder control box, plug into a wall outlet and turn on.
When the IR Transmit and IR Receive modules are aligned correctly (see additional sheet for alignment instructions)
the LEDs on the modules will be ON. If the LEDs are FLASHING, this means that the beams are not aligned or that the
control unit is not receiving the “beam detected” signal.
Operation
When the LaneMinder is ON, the POWER LED on the control box and the LEDs on the Transmit and Receive modules
are ON. This is known as DETECT mode.
When the beam is broken - ALARM MODE
Control unit - warning buzzer sounds and LED array flashes
Transmit and Receive modules - warning buzzer sounds and LED remains ON.
PIN delay: Pressing the PIN button shuts the beam off for approximately 2 minutes (adjustable)
to allow staff to go down the lane to attend to escaped pins etc without setting off the LaneMinder.
LEDs on Transmit and Receive modules will go out and then start flashing 30 seconds before time
period ends.
At the end of the time period, the LaneMinder automatically resets to DETECT mode.
LANE delay: Pressing the LANE button shuts off the beam for approximately 20 minutes (adjustable)
to allow staff to perform lane maintenance without setting off the LaneMinder. LEDs on the Transmit
and Receive modules will go out and then start flashing 60 seconds before the end of the time period.
At the end of the time period, the LaneMinder automatically resets to DETECT mode.
AISLE delay: Pressing the RED button on top of either of the Transmit or Receive modules will shut the beam off for
approximately 20 seconds (automatically doubles to 40 seconds when Beam 2 is plugged in) to allow staff to walk
down the side aisles of the centre without setting off the LaneMinder. The LEDs on the Transmit and Receive modules
will flash for this time period.
Over-ride priority - LANE over-rides PIN which over-rides AISLE.
RESET cancels ALL.
Adjustments
Infra-Red beam alignment and adjustment - refer to beam unit manufacturer’s instructions included in the LaneMinder 2 kit.
ALARM PIN -
approx.
1 sec to 15 sec
ALARM LANE BEAM 2
Rx
PIN
BEAM 2 BEAM 1 BEAM 1 EXT CUTOUT
Rx
Tx
Tx
BUZZER
approx.
30 sec to 4 min
LANE -
12VDC
+
(centre pole
is positive)
approx.
30 sec to 40 min
ADJUSTING POTS are 20 TURNS
CLOCKWISE INCREASES TIME
ANTI-CLOCKWISE DECREASES TIME
FACTORY SETTING is about 10 TURNS (1/2 way)
Options
BEAM 2 MODULE: Provides an ALARM for a second lane zone.
Cutout and Remote Control: A Cutout Control Module provides the interface required for a Remote Control Kit.
The Remote Control allows a small two-functon keyfob remote to control the LANES and RESET functions of the
LaneMinder2.
The Cutout Control Module also has a LANES and RESET button.
CUTOUT MODULE: Allows LaneMinder to interface with Pinspotter, Pinsetter or IR (infra-red) triggers
to shut them down for safety reasons if both BEAM 1 and BEAM 2 are broken in sequence.
CUTOUT modules are available in 8 lane and 2 lane units.
Basic LaneMinder2 STD layout
(for a single zone bowling centre)
tenpintec
tenpintec.com
MACHINE AREA
Use “MachineMinder” to provide intrusion protection to the machines
CURTAIN WALL
1
LANE AREA
16 LANE EXAMPLE
16
BEAM 1
5 to 15 ft
from
FOUL LINE
Rx
Tx
FOUL LINE
APPROACH AREA
LaneMinder 2
RESET
LANES
POWER
CONTROL DESK
PIN
LaneMinder2 layout for two zones
(with Remote Control option)
tenpintec
tenpintec.com
MACHINE AREA
MACHINE AREA
Use “MachineMinder” to provide intrusion protection for the machines
CURTAIN WALL
CURTAIN WALL
LANE AREA
LANE AREA
4 LANE EXAMPLE
16 LANE EXAMPLE
1
16
17
BEAM 2
BEAM 1
5 to 15 ft
from
FOUL LINE
Tx
20
Rx
FOUL LINE
Tx
5 to 15 ft
from
FOUL LINE
FOUL LINE
APPROACH AREA
APPROACH AREA
LaneMinder 2
RESET
LANES
PIN
POWER
CONTROL DESK
Buzzer Module
Buzzer Modules can be added to the
LaneMinder system as required.
These modules are controlled and
powered by either the Cat-5 cable
or the 12VDC output line (EXT BUZZER
on the rear of the LaneMinder 2
Control Module.)
The Remote Control Module receiver plugs into
the Cutout Control Module.
Using the Remote keyfobs you can control the LANES
and RESET functions of the LaneMinder system from
almost anywhere in the bowling centre.
Rx
Download PDF
Similar pages