G
Network Receiver
Owner’s Manual
• The R-N303 and R-N303D network receivers allow you to play back sound in
high-quality stereo at your own home.
• This manual explains preparations and operations for everyday users of the unit.
EN
English
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE USE. BE SURE TO FOLLOW THESE INSTRUCTIONS.
The precautions listed below are to prevent risk of harm to the user and others, as well as to prevent property
damage, and to help the user use this unit properly and safely. Be sure to follow these instructions.
After reading this manual, be sure to keep it in a safe place where
it can be referenced at any time.
• Be sure to request inspections or repairs from the dealer
where you purchased the unit or from qualified Yamaha
service personnel.
• Yamaha cannot be held responsible for damage caused by
improper use or modifications to the unit.
• This product is for ordinary homes. Do not use for
applications requiring high reliability, such as managing
lives, health care or high-value assets.
WARNING
This content indicates “risk of serious injury or death.”
■ Power supply/power cord
• Do not do anything that could damage the power cord.
- Do not place it near a heater.
- Do not bend it excessively or alter it.
- Do not scratch it.
- Do not place it under a heavy object.
Using the power cord with the core of the cord exposed could
cause electric shocks or a fire.
• Do not touch the power plug or cord if there is a chance of
lightning. Failure to observe this may cause electric shocks.
• Use this unit with the power supply voltage printed on it.
Failure to connect to an appropriate AC outlet may cause a fire,
electric shocks, or malfunctions.
• Check the electric plug periodically and remove any dirt or dust
which may have accumulated on it. Failure to observe this may
cause a fire or electric shocks.
• When setting up the unit, make sure that the AC outlet you are
using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and disconnect
the plug from the AC outlet. Even when the power switch is
turned off, as long as the power cord is not unplugged from the
wall AC outlet, the unit will not be disconnected from the
power source.
• If you hear thunder or suspect approaching lightning, quickly
turn off the power switch and pull the power plug from the AC
outlet. Failure to observe this may cause a fire or malfunctions.
• If not using the unit for long periods of time, be sure to pull the
power plug from the AC outlet. Failure to observe this may
cause a fire or malfunctions.
■ Do not disassemble
• Do not disassemble or modify this unit. Failure to observe this
may cause a fire, electric shocks, injury, or malfunctions. If you
notice any irregularities, be sure to request an inspection or
repair from the dealer where you purchased the unit or from
qualified Yamaha service personnel.
■ Water warning
• Do not expose the unit to rain, use it near water or in damp or
wet conditions, or place on it any containers (such as vases,
bottles or glasses) containing liquids which might spill into any
i En
openings. A liquid such as water getting into the unit may cause
a fire, electric shocks, or malfunctions. If any liquid such as
water seeps into the device, turn off the power immediately and
unplug the power cord from the AC outlet. Then, request an
inspection from the dealer where you purchased the unit or from
qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands. Do not
handle this unit with wet hands. Failure to observe this may
cause electric shocks or malfunctions.
■ Fire warning
• Do not place any burning items or open flames near the unit,
since they may cause a fire.
■ Maintenance and care
• Do not use aerosols or spray-type chemicals that contain
combustible gas for cleaning or lubrication. The combustible
gas will remain inside the unit, which may cause explosion or
fire.
■ Battery use
• Do not disassemble a battery. If the contents of the battery get
on your hands or in your eyes, it can cause blindness or
chemical burns.
• Do not dispose of batteries in fire. Doing so may result in the
battery bursting, causing a fire or injury.
• Do not expose a battery to high temperatures, such as direct
sunlight or a fire. The battery may burst, causing a fire or injury.
• Do not attempt to recharge batteries that are not intended to be
charged. Charging could cause the battery to burst or leak,
which can cause blindness, chemical burns, or injury.
• If the batteries do leak, avoid contact with the leaked fluid.
If the battery fluid should come in contact with your eyes,
mouth, or skin, wash immediately with water and consult a
doctor. Battery fluid is corrosive and may possibly cause loss of
sight or chemical burns.
■ Wireless unit
• Do not use this unit near medical devices or inside medical
facilities. Radio waves from this unit may affect electromedical
devices.
• Do not use this unit within 15 cm (6 in) of persons with a heart
pacemaker implant or a defibrillator implant. Radio waves from
this unit may affect electro-medical devices, such as a heart
pacemaker implant or defibrillator implant.
■ If you notice any abnormality
• If any of the following abnormalities occur, immediately turn
off the power and disconnect the power plug. If you are using
batteries, remove the batteries from this unit.
- The power cord/plug is damaged.
- An unusual smell or smoke is emitted from the unit.
- Foreign material gets into the interior of the unit.
- There is a loss of sound during use.
- There is a crack or damage in the unit.
Continued use could cause electric shocks, a fire, or
malfunctions. Immediately request an inspection or repair from
the dealer where you purchased the unit or from qualified
Yamaha service personnel.
• Be careful not to drop or apply strong impact to this unit. If you
suspect the unit may have been damaged due to dropping or
impact, immediately turn off the power and pull the power plug
from the AC outlet. Failure to observe this may cause electric
shocks, a fire, or malfunctions. Immediately request an
inspection from the dealer where you purchased the unit or from
qualified Yamaha service personnel.
CAUTION
• When turning on the AC power in your audio system, always
turn on the unit LAST, to avoid hearing loss and speaker
damage. When turning the power off the unit should be turned
off FIRST for the same reason. Failure to observe the above
may cause hearing impairment or speaker damage.
■ Maintenance
• Remove the power plug from the AC outlet when cleaning the
unit. Failure to observe this may cause electric shocks.
■ Handling caution
• Do not use an AC outlet where the power plug fits loosely when
inserted. Failure to observe this may cause a fire, electric
shocks, or burns.
• When removing the electric plug from an AC outlet, always
hold the plug itself and not the cord. Pulling by the cord can
damage it and cause electric shocks or a fire.
• Insert the power plug firmly all the way into the AC outlet.
Using the unit when it is not plugged in sufficiently can cause
dust to accumulate on the plug, causing a fire or burns.
• Do not insert foreign materials such as metal or paper into the
ventilation holes of this unit. Failure to observe this may cause a
fire, electric shocks, or malfunctions. If foreign material gets
into the unit, immediately shut off the power and pull the power
plug from the AC outlet / then turn off any amplifiers and
receivers and request an inspection from the dealer where you
purchased the unit or from qualified Yamaha service personnel.
• Do not rest your weight on the unit or place heavy objects on it.
Avoid applying excessive force to the buttons, switches or
connectors. Failure to observe the above may cause injury or
unit damage.
• Avoid pulling the connected cables to prevent injuries or
damage to the unit by causing it to fall.
■ Installation
■ Battery use
• Do not place the unit in an unstable position where it might
accidentally drop or fall over and cause injuries.
• Do not block this unit's ventilation holes (cooling slits). This
unit has ventilation holes on the top/bottom to prevent the
internal temperature from becoming too high. Failure to
observe this may trap heat inside the unit, causing a fire or
malfunctions.
• When installing this unit:
- Do not cover it with any cloth.
- Do not install it on a carpet or rug.
- Make sure the top surface faces up; do not install on its sides
or upside down.
- Do not use the device in a confined, poorly-ventilated
location.
Failure to observe the above may trap heat inside the unit,
causing a fire or malfunctions. Ensure that there is adequate
space around the unit: at least 30 cm (11-3/4 in) on top, 20 cm
(7-7/8 in) on the sides, and 20 cm (7-7/8 in) on the rear.
• Ensure that the top is facing upwards. Failure to observe this
may cause malfunctions or for the unit to fall and cause injury.
• Do not place the unit in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
• Avoid being near the unit during a disaster, such as an
earthquake. Since the unit may turn over or fall and cause
injury, quickly move away from the unit and go to a safe place.
• Before moving this unit, be sure to turn off the power switch and
disconnect all connection cables. Failure to observe this may
damage the cables or cause you or someone else to trip and fall.
• Always replace all batteries at the same time. Do not use new
batteries together with old ones. Using new ones with old ones
could cause a fire, burns, or inflammation due to fluid leaks.
• Do not mix battery types, such as alkaline batteries with
manganese batteries, or batteries from different makers, or
different types of batteries from the same maker, since this can
cause a fire, burns, or inflammation due to fluid leaks.
• Keep batteries away from children. A child could accidentally
swallow a battery. Failure to observe this may also cause
inflammation due to battery fluid leaks.
• Do not put in a pocket or bag, carry, or store batteries together
with pieces of metal. The battery could short, burst, or leak,
causing a fire or injury.
• Always make sure all batteries are inserted in conformity with
the +/- polarity markings. Failure to do so might result in a fire,
burns, or inflammation due to fluid leaks.
• When the batteries run out, or if the unit is not to be used for a
long time remove the batteries from the remote control to
prevent possible leakage of the battery fluid.
• When storing or discarding batteries, insulate the terminal area
by applying tape, or some other protection. Mixing them with
other batteries or metal objects can cause a fire, burns, or
inflammation due to fluid.
■ Power supply/power cord
Caution
Do not touch the surface marked with
this label.
The surface may become hot during
operation.
English
This content indicates “risk of injury.”
■ Hearing loss
• Do not use the unit/speakers or headphones for a long period of
time at a high or uncomfortable volume level, since this can
cause permanent hearing loss. If you experience any hearing
loss or ringing in the ears, consult a physician.
• Before connecting the unit to other devices, turn off the power
for all devices. Also, before turning the power of all devices on
or off, make sure that all volume levels are set to the minimum.
Failing to do so may result in hearing loss, electric shock, or
device damage.
ii En
Notice and Information
Notice
Information
Indicates points that you must observe in order to
prevent product failure, damage or malfunction and
data loss, as well as to protect the environment.
Indicates information of note regarding this product.
■ Power
• The illustrations and screens in this manual are for instructional
purposes only.
• The company names and product names in this manual are the
trademarks or registered trademarks of their respective
companies.
• Software may be revised and updated without prior notice.
• Information marked by the “ WARNING” icon indicates
points that may lead to death or serious injury if not observed.
• Information marked with the “ CAUTION” icon indicates
points that may lead to injury if not observed.
• Information in the “Notice” sections indicates points that you
must observe to prevent product failure, damage or malfunction
and data loss.
• Information listed in the “Note” sections indicates
supplementary information.
• This manual describes the “iPod touch”, “iPhone” and “iPad”
collectively as the “iPhone”. (“iPhone” refers to the “iPod
touch”, “iPhone” and “iPad”, unless otherwise specified.)
• In this manual, illustrations of English menu screens are used as
examples.
• Indicates points that you must observe in order to prevent
product failure, damage or malfunction and data loss, as well as
to protect the environment.
■ Installation
• Do not use this unit in the vicinity of other electronic
equipment, such as a TV, radio or mobile phone. Failure to
observe this may cause this unit or the TV or radio to produce
noise.
• Do not use this unit in a location that is exposed to direct
sunlight (such as a vehicle interior), that becomes extremely
hot, such as near a heater, or extremely cold, or that is subject to
excessive dust or vibration. Failure to observe this may cause
the unit's panel to become deformed, the internal components to
malfunction, or for operation to become unstable.
• Install this unit as far away from other electronic equipment as
possible. Digital signals from this unit may interfere with other
electronic equipment.
• If using a wireless network or Bluetooth, avoid installing this
unit near metal walls or desks, microwave ovens, or other
wireless network devices.
■ Connections
• If connecting external units, be sure to thoroughly read the
manual for each unit and connect them in accordance with the
instructions. Failure to properly handle a unit in accordance
with the instructions could cause malfunctions.
• Do not connect this unit to industrial units. Digital audio
interface standards for consumer use and industrial use are
different. This unit has been designed to connect to a consumeruse digital audio interface. Connections to an industrial-use
digital audio interface could not only cause this unit to
malfunction, but could also damage the speakers.
■ Handling
• Do not place vinyl, plastic, or rubber products on this unit.
Failure to observe this may cause discoloration or deformation
in the panel of this unit.
• If the ambient temperature changes drastically (such as during
unit transportation or under rapid heating or cooling) and there
is a chance condensation may have formed in the unit, leave the
unit for several hours without turning on the power until it is
completely dry before use. Using the unit while there is
condensation can cause malfunctions.
■ Maintenance
• When cleaning the unit, use a dry, soft cloth. Using chemicals
such as benzine or thinner, cleaning agents, or chemical
scrubbing cloths can cause discoloration or deformation.
■ Batteries
• Be sure to discard used batteries in accordance with local
regulations.
iii En
■ About content in this manual
Contents
Supplied accessories ................................................... 3
Controls and functions ............................................... 4
Front panel ..................................................................... 4
Front display .................................................................. 6
Rear panel ...................................................................... 7
Remote control............................................................... 8
Registering to a preset ................................................. 36
Recalling a preset......................................................... 36
Clearing a preset .......................................................... 36
ADVANCED OPERATION
Configuring playback settings for different
playback sources (OPTION menu)......................37
OPTION menu items ................................................... 37
Connections ............................................................... 10
Connecting audio devices ............................................ 10
Connecting the speakers .............................................. 11
Connecting the FM/AM antennas (R-N303) ............... 12
Connecting the DAB/FM antenna (R-N303D)............ 12
Connecting the network cable ..................................... 13
Preparing a wireless antenna ....................................... 13
Connecting power cord................................................ 13
Turning on the unit ...................................................... 13
Connecting to a network .......................................... 14
Sharing the iOS device setting..................................... 15
Configuring with the router’s WPS push button ......... 16
Set the wireless network connection manually............ 16
Connecting a mobile device to the unit directly
(Wireless Direct) ..................................................... 17
Verify the network connection status .......................... 18
Configuring MusicCast................................................ 19
BASIC OPERATION
Playback .................................................................... 20
Playing a source........................................................... 20
Switching information on the front display ................. 20
Using the sleep timer ................................................... 21
Listening to FM/AM radio....................................... 22
FM/AM tuning............................................................. 22
Using preset functions ................................................. 22
Radio Data System tuning
(Only for U.K. and Europe models) ........................ 25
Configuring various functions (SETUP menu) ......39
SETUP menu items ..................................................... 39
Network ....................................................................... 40
Bluetooth ..................................................................... 41
Balance ........................................................................ 41
Max Volume ................................................................ 41
InitialVolume............................................................... 42
AutoPowerStby (Auto Power Standby)....................... 42
Configuring the system settings
(ADVANCED SETUP menu)...............................43
ADVANCED SETUP menu items .............................. 43
Checking the firmware version (VERSION)............... 43
Selecting the remote control ID (REMOTE ID).......... 43
Setting tuner frequency step (TU) ............................... 43
Restoring the default settings (INIT)........................... 43
Updating the firmware (UPDATE) ............................. 44
Updating the unit’s firmware...................................45
ADDITIONAL INFORMATION
Troubleshooting.........................................................46
Supported devices and file formats .........................52
Supported devices........................................................ 52
Supported file formats ................................................. 52
Specifications .............................................................53
Trademarks ...............................................................55
Index ...........................................................................56
ADDITIONAL
INFORMATION
PREPARATION
PREPARATION
Sources that can be played back on this unit ................. 2
BASIC
OPERATION
What you can do with this unit ................................. 2
Registering the current playback song/station
(Preset function) ....................................................36
ADVANCED
OPERATION
INTRODUCTION
INTRODUCTION
Contents
Listening to DAB radio (R-N303D)......................... 26
Preparing the DAB tuning ........................................... 26
Selecting a DAB radio station for reception................ 26
Using preset function................................................... 27
Displaying the DAB information................................. 28
Checking reception strength of each DAB channel
label ......................................................................... 29
Playing back music via Bluetooth............................ 30
Connecting a Bluetooth device (pairing) ..................... 30
Playing back Bluetooth device contents ...................... 30
Disconnecting a Bluetooth connection ........................ 31
English
Playing back music stored on media servers
(PCs/NAS) ............................................................. 32
Setting the media sharing of music files...................... 32
Playback of PC music contents.................................... 33
Listening to Internet radio....................................... 34
Playing back music with AirPlay ............................ 35
Playback of iTunes/iPhone music contents ................. 35
1 En
INTRODUCTION
What you can do with this unit
This unit is a network receiver compatible with a network source such as a media server and mobile device.
It supports playback from not only analog sources such as a CD player or AM/FM radio, but also from Bluetooth devices
and network streaming services.
Sources that can be played back on this unit
1 Internet
2 Streaming service
Modem
Wi Fi
BLUETOOTH
DISPLAY
MODE
MEMORY
BAND
PRESET
TUNING
VOLUME
SELECT
BASS
PHONES
TREBLE
INPUT
PUSH
ENTER
SPEAKERS
RETURN
Router*
CONNECT
3 PC
5 AirPlay (iTunes)
This unit
Mobile
device
4 NAS
7 CD player etc.
5 AirPlay (iPhone/iPad/iPod touch)
6 Bluetooth
8 Radio
*
You need a commercially available wireless router (access point) when you use a mobile device.
1 Play back the Internet radio (p. 34)
5 Play back music files with AirPlay (p. 35)
2 Play back the streaming service
(See the supplement for each service.)
6 Play back audio content from Bluetooth
devices (p. 30)
3 Play back music files stored on your PC (p. 32)
7 Play back your external component (p. 10)
4 Play back music files stored on your NAS
(p. 32)
8 Listening to radio (p. 22, 26)
Note
For details on connecting the external devices, see “Connections” (p. 10).
2 En
What you can do with this unit
Supplied accessories
AM antenna (R-N303)
FM antenna (R-N303)
*
One of the above is supplied depending
on the region of purchase.
DAB/FM antenna
(R-N303D)
Batteries (x2)
(AA, R6, UM-3)
R-N303/R-N303D Owner’s Manual
CD-ROM (Europe model)
R-N303/R-N303D Owner’s Manual
(except Europe model, this book)
G
Network Receiver
■
■
■
■
R-N303/R-N303D Quick Start Guide
(Europe model)
G
Network Receiver
Réseau Ampli-Tuner
English
Remote control
INTRODUCTION
Check that the following accessories are supplied with the product.
3 En
Controls and functions
Front panel
12
3 4 5 6 7
8 90
AB
Wi Fi
BLUETOOTH
DISPLAY
MODE
MEMORY
BAND
PRESET
TUNING
VOLUME
SELECT
BASS
PHONES
TREBLE
INPUT
PUSH
ENTER
SPEAKERS
RETURN
CONNECT
C
D
E
1 A (power)
Turns on/off (standby) the unit.
2 STANDBY/ON indicator
Brightly lit: Power is on
Dimly lit: Standby mode
F
G
H
I
J
8 PRESET j / i
Recalls a preset radio station (p. 24, 22) or song/
streaming station (p. 36).
9 BLUETOOTH indicator
Lights up when the unit is connecting to a Bluetooth
device.
Note
When not using this unit for an extended period of time, be sure
to unplug it from the power outlet. This unit uses a minimal
amount of power even in standby mode.
3 Front display
Shows information about the operational status of this
unit (p. 6).
4 DISPLAY
Selects the information displayed on the front display
(p. 20).
5 MODE
Sets the FM band reception mode to automatic stereo
or monaural (p. 22).
6 MEMORY
Registers the current radio station as a preset when
TUNER is selected as the input source (p. 23, 27).
Registers the current playback song or streaming
station as a preset when NET are selected as the input
source (p. 36).
7 BAND
Sets the radio tuner band when TUNER is selected as
the input source. (p. 22, 26)
4 En
0 Wi-Fi indicator
This lights when connecting to a wireless network, or
when the unit is operating as an access point.
It also lights up if you register the unit with the
MusicCast CONTROLLER app, even if the unit is
connected to a wired network.
A Remote control sensor
Receives infrared signals from the remote control.
B TUNING jj / ii
Selects the tuning frequency (p. 22) or a DAB radio
station (p. 26) when TUNER is selected as the input
source.
Controls and functions
C PHONES jack
Outputs audio to your headphones for private
listening.
INTRODUCTION
D SPEAKERS A/B
Turns on or off the speaker set connected to the
SPEAKERS A and/or SPEAKERS B terminals on the
rear panel each time the corresponding button is
pressed.
E BASS +/–
Increases or decreases the low frequency response.
Control range: –10 to +10 (20 Hz)
F TREBLE +/–
Increases or decreases the high frequency response.
Control range: –10 to +10 (20 kHz)
G INPUT l / h
Selects the input source you want to listen to.
H SELECT/ENTER (jog dial)
Turn the dial to select a numeric value or setting, and
press the dial to confirm.
I RETURN
Returns to the previous indication of the front display.
CONNECT
Use to control the unit using the dedicated MusicCast
CONTROLLER app for mobile devices.
See MusicCast Setup Guide for details.
English
J VOLUME control
Increases or decreases the sound output level.
5 En
Controls and functions
Front display
1
2
3 4
5
6
STEREO SP A MUTE
TUNED SP B SLEEP
Note
You can change the brightness level of the front display by pressing DIMMER (p. 8).
1 Information display
Displays the current status (such as input name).
You can switch the information that is displayed when
you press DISPLAY (p. 20).
2 STEREO indicator
Lights up when the unit is receiving a stereo FM radio
signal.
3 TUNED indicator
Lights up when the unit is receiving an FM/AM radio
station signal.
Note
AM radio is available only for R-N303.
4 Speaker indicators
“SP A” lights up when the SPEAKERS A output is
enabled and “SP B” lights up when the SPEAKERS B
output is enabled.
5 MUTE indicator
Blinks when audio is muted.
6 SLEEP indicator
Lights up when the sleep timer is on (p. 21).
6 En
Controls and functions
12
3
4
INTRODUCTION
Rear panel
5
SERVICE
ANTENNA
NETWORK
FM
AM
75
SPEAKERS
VOLTAGE SELECTOR
A OR B:8ΩMIN./SPEAKER
0
20
220 240 V
DIGITAL
A
OPTICAL
PHONO
CD
LINE
IN
GND
OUT
CLASS 2 WIRING
CABLAGE CLASSE 2
COAXIAL
B
2
6 7
8 9
0
A
B
(R-N303 except Europe model)
* The R-N303 Europe model and R-N303D are as shown below.
CD
LINE
IN
2
9
OUT
3
0
1 SERVICE jack
This jack is for support use, and is normally not used.
2 NETWORK jack
For connecting to a network with a network cable
(p. 13).
7 COAXIAL jack
For connecting to audio components equipped with a
coaxial digital output (p. 10).
8 PHONO jacks (R-N303 except Europe model)
For connecting to a turntable (p. 10).
3 ANTENNA terminals
For connecting to the radio antennas (p. 12).
9 CD jacks
For connecting to a CD player (p. 10).
4 Wireless antenna
For connecting to a network device wirelessly (p. 13).
0 LINE 1-3 jacks (R-N303 Europe model, R-N303D)
6 OPTICAL jack
For connecting to audio components equipped with
optical digital output (p. 10).
A SPEAKERS terminals
Used to connect speakers (p. 11).
B VOLTAGE SELECTOR
(Only for General model)
English
5 Power cord
For connecting to an AC wall outlet (p. 13).
LINE 1-2 jacks (R-N303 except Europe model)
For connecting to analog audio components (p. 10).
7 En
Controls and functions
Remote control
5 SPEAKERS A/B
Turns on and off the set of speakers connected to the
SPEAKERS A and/or SPEAKERS B terminals on the
rear panel of this unit when the corresponding key is
pressed.
1
2
3
4
DIMMER
SLEEP
A
B
5
6 Input selection keys
Select the input source you want to listen to.
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
Note
6
TUNER
7
NET
BAND
BLUETOOTH
TUNING
MEMORY
PRESET
8
9
0
NET key is for network source. Press repeatedly to select a
desired network source.
CLEAR
MODE
F
DISPLAY
G
A
ENTER
HOME
RETURN
B
SETUP
OPTION
C
H
VOLUME
NOW PLAYING
MUTE
D
I
J
REPEAT
SHUFFLE
E
7 Radio keys
Operate the radio.
BAND
Sets the radio tuner band when
TUNER is selected as the input
source (p. 22, 26).
TUNING jj / ii Selects the tuning frequency
(p. 22) or a DAB radio station
(p. 26) when TUNER is selected
as the input source.
8 MEMORY
Registers the current radio station as a preset when
TUNER is selected as the input source (p. 23, 27).
Registers the current playback song or streaming
station as a preset when NET are selected as the input
source (p. 36).
9 CLEAR
Deletes the preset memory (p. 24, 28, 36).
0 MODE
Sets the FM band reception mode to automatic stereo
or monaural (p. 22).
A Menu operation keys
Cursor keys
Selects a menu, setting value or
other parameter.
ENTER
Confirms a selected item.
RETURN
Returns to the previous state.
(R-N303, except Europe model)
1 Infrared signal transmitter
Sends infrared signals.
2 A (power)
Turns on/off (standby) the unit.
3 SLEEP
Sets the sleep timer (p. 21).
4 DIMMER
Changes the brightness level of the front display.
Choose brightness from 5 levels by pressing this key
repeatedly.
8 En
B HOME
Moves up top level when selecting music files,
folders, etc.
C SETUP
Displays the “SETUP” menu (p. 39).
D NOW PLAYING
Displays music information when selecting music
files, folders, etc.
Controls and functions
■ Installing batteries
Change all batteries if you notice the operation range of
the remote control narrows. Before inserting new
batteries, wipe the battery compartment clean.
Note
Yamaha does not guarantee the operation of all Bluetooth devices.
F PRESET j / i
Recalls a preset radio station (p. 24, 22) or song/
streaming station (p. 36).
INTRODUCTION
E Playback keys
Let you play back and perform other operations for
network sources and Bluetooth devices.
G DISPLAY
Selects the information displayed on the front display
(p. 20).
H OPTION
Displays the “OPTION” menu (p. 37).
AA, R6, UM-3 batteries
I MUTE
Mutes the audio output.
■ Operation range
Point the remote control at the remote control sensor on
this unit and remain within the operating range shown
below. The area between the remote control and this unit
must be clear of large obstacles.
Approximately
6 m (20 ft)
Remote control
English
J VOLUME +/–
Increases or decreases the sound output level.
9 En
PREPARATION
Connections
Connecting audio devices
Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will
be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and
lack bass. Refer to the owner’s manual for each of your components.
Make sure to use RCA cables to connect audio components.
CAUTION
• Do not connect this unit or other components to the main power until all connections between components are
complete.
• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the
speakers.
CD player, etc.
Audio output
(digital coaxial)
C
CD recorder, etc.
DVD player, etc.
Audio output
(digital optical)
Audio
output
O
Audio
input
(R-N303 except Europe model)
SERVICE
ANTENNA
NETWORK
FM
75
AM
SPEAKERS
A OR B:8ΩMIN./SPEAKER
DIGITAL
A
OPTICAL
PHONO
GND
CD
LINE
IN
OUT
CLASS 2 WIRING
CABLAGE CLASSE 2
COAXIAL
B
2
GND
Audio
output
Audio
output
Turntable
CD player
Speakers A
Note
The input jacks are different on the R-N303 Europe model and on the R-N303D (p. 7).
Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit.
10 En
Speakers B
Connections
• Do not bundle audio cables and speaker cables together with the
power cord. Doing so may generate noise.
• The PHONO jacks are designed for connecting a turntable with
an MM cartridge.
• Connect your turntable to the GND terminal to reduce noise in
the signal. However, for some turntables, you may hear less
noise without the GND connection.
• On the R-N303D and R-N303 Europe models, to prevent sound
loops, no sound will be outputted from the LINE 3(OUT) jack
while the LINE 3 input is selected. On other models, no sound
will be outputted from the LINE 2(OUT) jack while the LINE 2
input is selected.
■ Connecting via banana plug
(North America, Australia,
General models only)
Tighten the knob and then insert the banana plug into the
end of the corresponding terminal.
Banana plug
■ Bi-wire connection
Connecting the speakers
CAUTION
Connect the speakers with an impedance as shown below.
If you connect speakers with an excessively low
impedance, this unit may overheat.
Bi-wire connection separates the woofer from the
combined midrange and tweeter section. A bi-wire
compatible speaker has four binding post terminals. These
two sets of terminals allow the speaker to be split into two
independent sections. With these connections, the mid and
high frequency drivers are connected to one set of terminals
and the low frequency driver to another set of terminals.
This unit
Speaker connection
SPEAKERS A or
SPEAKERS B
8  or higher
SPEAKERS A and
SPEAKERS B
16  or higher
(except for North America model)
Bi-wiring
8  or higher
Speaker
SPEAKERS
Speaker impedance
PREPARATION
Note
A OR B:8ΩMIN./SP
A
CLASS 2 WIR
CABLAGE CLA
B
■ Connecting speaker cables
a Remove approximately 10 mm (3/8") of insulation
from the ends of the speaker cable and twist the bare
wires of the cable firmly together.
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the
side (upper right or bottom left) of the terminal.
d Tighten the terminal.
10 mm
(3/8")
a
Connect the other speaker to the other set of terminals in
the same way.
Note
• When making bi-wire connections, remove the shorting bridges
or cables on the speaker. Refer to the speakers’ instruction
manuals for more information.
• To use the bi-wire connections, press SPEAKERS A and
SPEAKERS B (p. 8) so that both speaker indicators (“SP A”
and “SP B”) light up on the front display.
c
b
DISPLAY
MODE
MEMORY
BAND
PRESET
TUNING
VOLUME
SELECT
BASS
PHONES
TREBLE
INPUT
PUSH
ENTER
SPEAKERS
RETURN
CONNECT
d
SPEAKERS A/B
Note
When inserting speaker cables into the speaker terminals, insert
only the bare speaker wire. If insulated cable is inserted, the
connection may be poor and sound may not be heard.
DIMMER
English
Red:positive (+)
Black:negative (–)
SLEEP
A
SPEAKERS A/B
B
SPEAKERS
OPTICAL
COAXIAL
CD
11 En
Connections
Connecting the FM/AM antennas
(R-N303)
Connecting the DAB/FM antenna
(R-N303D)
Connect the supplied FM/AM antenna to this unit.
Fix the end of the FM antenna to a wall, and place the AM
antenna.
Connect the supplied DAB/FM antenna to this unit and fix
the antenna ends to a wall.
FM antenna
AM antenna
DAB/FM antenna
SERVICE
SERVICE
ANTENNA
ANTENNA
DAB FM
NETWORK
NETWORK
FM
FM
75
75
AM
75
AM
DIGITAL
DIGITAL
OPTICAL
OPTICAL
PHONO
CD
CD
LINE
IN
GND
LINE
IN
OUT
OUT
COAXIAL
COAXIAL
(except Europe model)
Note
Note
• If you experience poor reception quality, install an outdoor
antenna.
• Unwind only the length of cable needed from the AM antenna
unit.
• The wires of the AM antenna have no polarity.
■ Assembling the supplied AM antenna
■ Connecting the wires of the AM antenna
2 Insert
1 Hold down
12 En
• If you experience poor reception quality, install an outdoor
antenna.
• The antenna should be stretched out horizontally.
Connections
Connecting the network cable
Connecting power cord
Connect the unit to your router with a commerciallyavailable STP network cable (CAT-5 or higher straight
cable).
Plug the power cord into an AC wall outlet after all other
connections are complete.
WARNING
Use STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference.
Internet
Network Attached
Storage
(NAS)
Only for General model:
Before connecting the power cord, make sure you set
VOLTAGE SELECTOR of this unit according to your
local voltage. Improper setting of VOLTAGE SELECTOR
may cause fire and damage to this unit.
WAN
LAN
To the AC wall outlet
with the power cord
MAINS
Modem
VOLTAGE SELECTOR
0
Router
PC
220 240 V
VOLTAGE SELECTOR
0
Mobile device
(such as iPhone)
20
PREPARATION
Note
20
220 240 V
Network cable
Turning on the unit
SERVICE
Press A (power) to turn on the unit.
ANTENNA
NETWORK
FM
AM
75
DIMMER
This unit (rear)
(R-N303)
SLEEP
A (power)
A
B
SPEAKERS
Preparing a wireless antenna
COAXIAL
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
BAND
TUNING
MEMORY
CLEAR
CD
PRESET
MODE
DISPLAY
English
If you connect the unit wirelessly, erect the wireless
antenna. For information on how to connect the unit to a
wireless network, see “Connecting to network” (p. 14).
For more information on using this unit with a Bluetooth
device, see “Playing back music via Bluetooth” (p. 30).
OPTICAL
Notice
Do not apply excessive force on the wireless antenna. Doing so
may damage the antenna.
13 En
Connecting to a network
There are several methods to connect the unit to a network. Select a connection method according to your environment.
Note
• Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the
unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately.
• Each server must be connected to the same subnet as the unit.
• To use the service via the Internet, broadband connection is strongly recommended.
• When playing a high-resolution audio source via the network, we recommend connecting by cable to the router for stable playback.
WAC (Wireless Accessory Configuration)
If you turn on the power to the unit right after you purchase or
initialize it, the unit will automatically use the network settings of the
iOS device (iPhone/iPad/iPod touch) and try to connect to a wireless
LAN (unless the unit is already connected to a wired LAN).
WAC
R-N303 XXXXXX
R-N303 (example)
If you have an iOS device, follow the procedure from Step 6 in the section “Sharing the iOS device setting” (p. 15).
If you plan to connect the unit wirelessly by another method, press RETURN to exit the current screen, and then proceed to one of
the sections below.
■ Connecting with a wireless router (access point)
Connect to the network with the method listed below that corresponds to your environment.
Connecting with the MusicCast CONTROLLER
app
See “Configuring MusicCast”
(p. 19) for details.
Connecting using the Wi-Fi setting of the iOS
device (iPhone / iPad / iPod touch)
Share the Wi-Fi setting of the iOS
device (p. 15)
Connecting using WPS push button configuration
on the wireless router (or access point)
Use the WPS push button
configuration (p. 16)
Connecting with a wireless router (access point)
without WPS push button configuration
Set the network connection
manually (p. 16)
■ Connecting to a router using a cable
Connecting using the DHCP server function of the
router
You can connect to the network by
simply making a wired connection
(p. 13)
Note
• For information on how to set the IP address and other menu items, please refer to page 40.
• To switch from a wireless LAN connection to a wired LAN connection, set the “Connection” under the “Network” setup menu to
“Wired” (p. 40).
14 En
Connecting to a network
■ Connecting without a wired router or wireless router (access point)
Connecting wirelessly to a mobile device
(Wireless Direct)
Connect wirelessly with Wireless
Direct (p. 17)
Note
Sharing the iOS device setting
5
You can easily setup a wireless connection by applying the
connection settings on iOS devices (iPhone/iPad/iPod
touch).
Before proceeding, confirm that your iOS device is
connected to a wireless router (access point).
When connected to a wired network, the front display will show
the messages “LAN CBL” and “Pls disconnect”. Unplug the
network cable from the unit, and press the ENTER key.
Note
6
Note
• If you perform the following procedure, all network settings will be
initialized.
• This configuration does not work if the security protocol of your
wireless router (access point) is WEP. In this case, use another
connection method.
CLEAR
Cursor keys  / 
ENTER
MODE
Use the cursor keys ( / ) to select “Share
Setting” and then press ENTER twice.
PREPARATION
When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play
back contents from the Internet or to update the firmware of this unit over the network, connect the unit to a network with a wired router
or wireless router (access point).
On the iOS device, select the unit as the
AirPlay speaker in the Wi-Fi screen.
Example (iOS 10)
DISPLAY
ENTER
The name of this unit
HOME
RETURN
RETURN
SETUP
SETUP
OPTION
VOLUME
NOW PLAYING
7
Check that the “Network” field is set to your
preferred network, and then tap “Next”.
MUTE
Tap here to start setup
1
2
Press SETUP.
Use the cursor keys ( / ) to select
“Network” and press ENTER.
The network currently
selected
3
Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4
Use the cursor keys ( / ) to select
“Wireless” and press ENTER.
When the sharing process finishes, the unit is
automatically connected to the selected network
(access point).
When the setting finishes, verify whether the unit is
connected to a wireless network (p. 18).
WIRELESS
¡WPS
15 En
English
Note
To return to the previous state, press RETURN.
Connecting to a network
Configuring with the router’s WPS
push button
Set the wireless network connection
manually
You can easily set up a wireless connection with one push
of the WPS button.
Before performing the following procedure, check the
security method and security key on the wireless router
(access point).
Note
This configuration does not work if the security method of your
wireless router (access point) is WEP or WPA2-TKIP. In this
case, use another connection method.
CLEAR
MODE
CLEAR
Cursor keys
ENTER
DISPLAY
MODE
DISPLAY
ENTER
HOME
RETURN
SETUP
OPTION
RETURN
Cursor keys  / 
ENTER
ENTER
SETUP
VOLUME
NOW PLAYING
HOME
MUTE
RETURN
RETURN
SETUP
SETUP
OPTION
VOLUME
NOW PLAYING
1
2
MUTE
1
2
Press SETUP.
Use the cursor keys ( / ) to select
“Network” and press ENTER.
Press SETUP.
Note
Use the cursor keys ( / ) to select
“Network” and press ENTER.
To return to the previous state, press RETURN.
3
Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4
Use the cursor keys ( / ) to select
“Wireless” and press ENTER.
5
Use the cursor keys ( / ) to select
“ManualSetting” and press ENTER.
Note
To return to the previous state, press RETURN.
3
Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4
Use the cursor keys ( / ) to select
“Wireless” and press ENTER.
WIRELESS
¡WPS
5
Press ENTER twice.
“Connecting” appears on the front display.
6
Push the WPS button on the wireless router
(access point).
When the connection process finishes, “Completed”
appears on the front display. When the setting
finishes, verify whether the unit is connected to a
wireless network (p. 18).
If “Completed” does not appear, repeat from Step 1 or
try another connection method.
7
To exit from the menu, press SETUP.
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the
Wi-Fi Alliance, which allows easy establishment of a
wireless home network.
16 En
MANUAL
¡SSID
6
Use the cursor keys ( / ) to select “SSID”
and press ENTER.
SSID
¡
Connecting to a network
8
Use the cursor keys to enter the SSID on the
wireless router (access point), and press
RETURN to previous state.
Use the cursor keys (/) to select a character and
the cursor keys (/) to move the edit position.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
Connecting a mobile device to the
unit directly (Wireless Direct)
Using Wireless Direct, this unit can operate as a wireless
network access point that mobile devices can directly
connect to.
Use the cursor keys ( / ) to select
“Security” and press ENTER.
CLEAR
Cursor keys
ENTER
SECURITY
¡WPA2-PSK(AES)
9
MODE
DISPLAY
ENTER
HOME
RETURN
SETUP
OPTION
PREPARATION
7
RETURN
Use the cursor keys ( / ) to select desired
security method and press RETURN.
SETUP
VOLUME
NOW PLAYING
MUTE
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
Note
Note
If you select “None”, the connection may be insecure since the
communication is not encrypted.
10
Use the cursor keys ( / ) to select
“Security Key” and press ENTER.
KEY
You will not be able to connect your mobile device or this unit to
the Internet while Wireless Direct is in use. For this reason,
Internet-based services such as Internet radio will be unavailable.
1
2
Press SETUP.
Use the cursor keys ( / ) to select
“Network” and press ENTER.
Note
12
13
Use the cursor keys to enter the security key
on the wireless router (access point), and
press RETURN to previous state.
If you select “WEP” in Step 9, enter either 5 or 13
character string, or 10 or 26 hexadecimal digits.
If you select “WPA2-PSK (AES)” or “Mixed Mode”
in Step 10, enter either 8 to 63 character string or 64
hexadecimal digits.
Use the remote control keys as described in Step 7 to
enter the key.
To return to the previous state, press RETURN.
Use the cursor keys ( / ) to select
“Connect [ENT]” and press ENTER to save
the setting.
If the unit does not connect, check the SSID and
security key on the wireless router (access point) and
repeat from Step 6.
Verify whether the unit is connected to a wireless
network (p. 18).
5
Press ENTER to display the SSID for this
unit, and press RETURN to previous state.
6
Use the cursor keys ( / ) to select
“Security” and press ENTER.
3
Use the cursor keys ( / ) to select
“Connection” and press ENTER.
4
Use the cursor keys ( / ) to select
“W.Direct” and press ENTER.
W.DIRECT
¡SSID
W.DIRECT
¡WPA2-PSK(AES)
To exit from the menu, press SETUP.
17 En
English
11
Connecting to a network
7
Use the cursor keys ( / ) to select desired
security method and press RETURN.
Settings
None, WPA2-PSK (AES)
Verify the network connection status
Perform the following procedure to verify the unit’s
connection to a network.
Note
If you select “None”, go to step 10 below.
Note
When using Wireless Direct, you will not be able to check the
status of the network connection.
If you select “None”, the connection may be insecure since the
communication is not encrypted.
8
Use the cursor keys ( / ) to select
“Security Key” and press ENTER.
CLEAR
Cursor keys  / 
ENTER
KEY
9
10
11
Use the cursor keys to enter the security key
on this unit, and press RETURN to previous
state.
Enter either 8 to 63 character string or 64
hexadecimal digits.
Use the cursor keys (/) to select a character and
the cursor keys (/) to move the edit position.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
Use the cursor keys ( / ) to select
“Connect [ENT]” and press ENTER to save
the setting.
The SSID and security key information is required
for setup of a mobile device.
When you select the “SSID” in Step 5, you can
display the SSID configured for this unit.
If the Wireless Direct connection cannot be made, the
security key may be incorrect. Configure the Wi-Fi
settings of a mobile device again. You can verify
whether the unit is connected to a wireless network
(p. 18).
12
To exit from the menu, press SETUP.
18 En
DISPLAY
ENTER
HOME
RETURN
SETUP
OPTION
RETURN
SETUP
VOLUME
NOW PLAYING
1
2
MUTE
Press SETUP.
Use the cursor keys ( / ) to select
“Network” and press ENTER.
Note
To return to the previous state, press RETURN.
3
Use the cursor keys ( / ) to select
“Information” and press ENTER.
4
Use the cursor keys ( / ) to select
“STATUS”.
STATUS
¡Connect
Configure the Wi-Fi settings of a mobile
device.
For details on settings of your mobile device, refer to
the instruction manual of the mobile device.
(1) Enable the Wi-Fi function on the mobile device.
(2) Select the SSID of this unit from the list of
available access points.
(3) When you are prompted for a password, enter the
security key displayed in Step 9.
MODE
When “Connect” appears, the unit is connected to a
network. If “Disconnect” appears, reset connection.
5
To exit from the menu, press SETUP.
Connecting to a network
■ About MusicCast
Use MusicCast to share music between MusicCastcompatible devices in multiple rooms.
With the dedicated “MusicCast CONTROLLER” app, you
can easily enjoy music from your smartphone, a media
server (a personal computer or NAS) or Internet radio
(streaming services) wherever you are in your home.
• All MusicCast-compatible devices can be operated
from the dedicated “MusicCast CONTROLLER” app
• Multiple devices that support MusicCast in separate
rooms can be linked to play music simultaneously
• Supports music playback through Internet radio
(streaming services)
• Network settings for devices that support MusicCast
■ Registering a MusicCast network
Register this unit to a MusicCast network.
At the same time, configure the network connection
settings for this unit.
Note
When connecting to a wireless network, have the SSID and the
security key for the wireless LAN router (access point) on hand.
1
Start the “MusicCast CONTROLLER” app,
and tap “SETUP”.
Note
When configuring the settings on each subsequent device that
supports MusicCast, tap “Register New Device” in the app’s
“
”.
2
Following the instructions on the screen of
your mobile device, use the “MusicCast
CONTROLLER” and press the CONNECT
button on the front of this unit’s panel for five
seconds.
Visit the following website for more information on
MusicCast and on which devices are compatible.
http://www.yamaha.com/musiccast/
PREPARATION
Configuring MusicCast
Note
To use MusicCast, download the MusicCast Setup Guide from
the Yamaha Downloads website.
http://download.yamaha.com/
Wi Fi
BLUETOOTH
DISPLAY
MODE
MEMORY
BAND
PRESET
TUNING
VOLUME
SELECT
BASS
PHONES
TREBLE
INPUT
PUSH
ENTER
SPEAKERS
RETURN
CONNECT
■ MusicCast CONTROLLER
CONNECT
3
Note
AirPlay and DSD sound cannot be transmitted. Music can only be
played back from this unit.
English
To use network functionality with a device that supports
MusicCast, you need to use the “MusicCast
CONTROLLER” dedicated app for mobile devices.
Search for and install “MusicCast CONTROLLER” (free)
in the App Store or on Google Play.
Following the instructions on the screen of
your mobile device, use the “MusicCast
CONTROLLER” to configure the network
settings.
This completes the network settings for registering the
device to the MusicCast network.
Use “MusicCast CONTROLLER” to play back music.
19 En
BASIC OPERATION
Playback
Playing a source
DIMMER
Switching information on the front
display
A
SPEAKERS A/B
When you select a network source or Bluetooth as the
input source, you can switch playback information on the
front display.
SLEEP
B
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
BAND
TUNER
BLUETOOTH
NET
Input selection
keys
TUNING
MEMORY
CLEAR
PRESET
MODE
DISPLAY
DISPLAY
BAND
TUNING
MEMORY
PRESET
ENTER
CLEAR
MODE
DISPLAY
HOME
HOME
RETURN
RETURN
OPTION
SETUP
VOLUME
VOLUME
OPTION
SETUP
VOLUME
NOW PLAYING
NOW PLAYING
1
1
Press one of the input selection keys to
select the input source you want to listen to.
2
Press SPEAKERS A and/or SPEAKERS B to
select speakers A and/or speakers B.
The selected speakers will be enabled, and you can
confirm which speakers are selected on the front
display (p. 6).
Note
• When one set of speakers is connected using bi-wire
connections, or when using two sets of speakers simultaneously
(A and B), make sure “SP A” and “SP B” are displayed on the
front display.
• When listening with headphones, turn off the speakers.
3
4
MUTE
MUTE
Press DISPLAY.
Each time you press the key, the displayed item
changes.
SP A
INFO
Track
About 3 seconds later, the corresponding information
for the displayed item appears.
SERVER
› Track #1
Input source
SP A
Item
Play the source.
Bluetooth
Track (song title), Artist (artist name),
Album (album name)
Press VOLUME +/– to adjust the sound
output level.
Server
AirPlay
Track (song title), Artist (artist name),
Album (album name), Time (elapsed time)
Net Radio
Track (song title), Album (album name),
Time (elapsed time), Station (station name)
Note
• You can adjust the tonal quality by using the BASS +/– and
TREBLE +/– on the front panel (p. 5).
• You can also adjust the speaker balance by using the “Balance”
option in the “SETUP” menu (p. 41).
20 En
Note
“_” (underscore) will be displayed for characters not supported
by the unit.
Playback
Using the sleep timer
Use this feature to automatically set this unit to standby
mode after a certain amount of time. The sleep timer is
useful when you are going to sleep while this unit is
playing.
DIMMER
SLEEP
SLEEP
A (power)
A
B
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
BAND
TUNING
MEMORY
PRESET
MODE
DISPLAY
BASIC
OPERATION
CLEAR
Note
The sleep timer can only be set with the remote control.
1
Press SLEEP repeatedly to set the amount of
time before this unit is set to standby mode.
Each time you press SLEEP, the front display
changes as shown below.
Sleep 120 min.
Sleep Off
Sleep 90 min.
Sleep 30 min.
Sleep 60 min.
The SLEEP indicator blinks while setting the amount
of time for the sleep timer.
SLEEP
Sleep120 min.
If the sleep timer is set, the SLEEP indicator on the
front display lights up.
Note
English
• To disable the sleep timer, select “Sleep Off”.
• The sleep timer setting can also be canceled by pressing
A (power) to set this unit to standby mode.
21 En
Listening to FM/AM radio
■ Improving FM reception (FM mode)
Note
If the signal from the station is weak and the sound quality
is not good, set the FM band reception mode to monaural
mode to improve reception.
The R-N303D does not include an AM tuner.
FM/AM tuning
BAND
TUNING
MEMORY
CLEAR
DIMMER
PRESET
MODE
DISPLAY
SLEEP
MODE
A
B
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
ENTER
HOME
RETURN
TUNER
OPTION
SETUP
BAND
TUNING
BAND
MEMORY
CLEAR
VOLUME
TUNING jj / ii
NOW PLAYING
MUTE
PRESET
MODE
DISPLAY
1
1
Press TUNER to select “TUNER” as the input
source.
2
Press BAND repeatedly to select the
reception band (FM or AM).
3
Press TUNING jj / ii to set a frequency.
To search stations automatically, press and hold
TUNING jj / ii for a second.
If a broadcast is being received, the “TUNED”
indicator on the front display will light up. If a stereo
broadcast is being received, the “STEREO” indicator
will also light up.
STEREO SP A
TUNED
FM 87.55MHz
Press MODE repeatedly to select “Stereo”
(automatic stereo mode) or “Mono”
(monaural mode) when this unit is tuned in to
an FM radio station.
When Mono is selected, FM broadcasts will be heard
in monaural sound.
Note
The STEREO indicator on the front panel lights up while
listening to a station in stereo mode (p. 6).
Using preset functions
You can register up to 40 radio stations as presets. Once
you have registered stations, you can easily tune in to
them by recalling the presets. You can automatically
register FM stations that have strong signals. If the FM
stations you want to store have weak signals, you can
register them manually (p. 23).
Frequency
Note
• If the station signals are weak, tuning search does not stop at the
desired station.
• When the signal reception for an FM radio station is unstable,
switching to monaural may improve it.
22 En
■ Registering radio stations automatically
(FM station only)
Note
• When you register radio stations automatically, radio stations
currently registered to preset numbers may be overwritten.
• If the station you want to register is weak in signal strength, try
using the manual preset tuning method.
• Only for U.K. and Europe models:
Only Radio Data System broadcasting stations can be preset
automatically.
• FM stations registered as presets using the automatic preset
registration feature will be heard in stereo.
Listening to FM/AM radio
■ Registering a radio station manually
DIMMER
BAND
SLEEP
A
TUNING
MEMORY
B
PRESET
MEMORY
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
CLEAR
MODE
PRESET j / i
DISPLAY
ENTER
TUNER
BAND
TUNING
BAND
HOME
MEMORY
CLEAR
PRESET
MODE
RETURN
PRESET j / i
OPTION
SETUP
DISPLAY
VOLUME
NOW PLAYING
Cursor keys  / 
ENTER
MUTE
ENTER
2
Press MEMORY.
RETURN
RETURN
OPTION
SETUP
OPTION
VOLUME
NOW PLAYING
Tune in to the desired radio station.
See “FM/AM tuning” (p. 22).
MUTE
Note
1
Press TUNER to select “TUNER” as the input
source.
2
Press OPTION on the remote control.
The “OPTION” menu is displayed (p. 37).
3
Use the cursor keys ( / ) to select “Auto
Preset”, and then press ENTER.
By holding down MEMORY for more than 3 seconds, you
can skip the following steps and automatically register the
selected station to an empty preset number (i.e., the preset
number following the last preset number used).
3
BASIC
OPERATION
HOME
1
Press PRESET j / i to select the preset
number to which the station will be
registered.
When you select a preset number to which no station
is registered, the message “Empty” is displayed.
SP A
OPTION
Auto Preset
99.15
03: Empty
SP A
READY
01:FM 87.50MHz
Preset number
Frequency
This unit starts scanning the FM band about 5
seconds later from the lowest frequency upwards.
To begin scanning immediately, press ENTER.
Note
“Empty” (not in use) or the frequency
currently registered.
4
Press MEMORY.
When registration is complete, the display returns to
the original state.
Note
To cancel registration, press RETURN or do not perform any
operations for about 30 seconds.
English
• Before scanning begins, you can specify the first preset number
to be used by pressing PRESET j / i or cursor keys (/) on
the remote control.
• To cancel scanning, press RETURN.
When scanning is complete, “FINISH” is displayed and
then the display returns to original state.
23 En
Listening to FM/AM radio
■ Recalling a preset station
You can recall preset stations that you registered using
either an automatic station preset or manual station preset.
DIMMER
1
Press TUNER to select “TUNER” as the input
source.
2
3
Press OPTION.
SLEEP
A
Use the cursor keys ( / ) to select “Clear
Preset” and press ENTER.
B
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
CLEAR
01:FM 88.10MHz
Preset station to be cleared
TUNER
BAND
4
TUNING
MEMORY
CLEAR
PRESET
MODE
PRESET j / i
DISPLAY
CLEAR
01:Cleared
ENTER
1
Press TUNER to select “TUNER” as the input
source.
2
Press PRESET j / i to select a preset
number.
Note
• Preset numbers to which no stations are registered are skipped.
• “No Presets” is displayed if no stations are registered.
5
Repeat Step 4 until all desired preset stations
are cleared.
6
To exit from the “OPTION” menu, press
OPTION.
You can also use the following steps to cancel registration
of a station.
1
Press TUNER to select “TUNER” as the input
source.
2
Press CLEAR.
■ Clearing a preset station
You can clear radio stations that are registered to the
preset numbers.
OPTICAL
COAXIAL
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
CLEAR
01:FM 88.10MHz
CD
Preset station to be cleared
TUNER
BAND
CLEAR
3
TUNING
MEMORY
Use the PRESET j / i to select a preset
station to be cleared and press CLEAR.
If the preset station is cleared, “Cleared” appears.
PRESET
MODE
DISPLAY
CLEAR
Cursor keys  / 
ENTER
ENTER
HOME
RETURN
SETUP
OPTION
OPTION
VOLUME
NOW PLAYING
24 En
Use the cursor keys ( / ) to select a preset
station to be cleared and press ENTER.
If the preset station is cleared, “Cleared” appears and
then the next in-use preset number is displayed.
MUTE
Listening to FM/AM radio
Radio Data System tuning (Only for
U.K. and Europe models)
Radio Data System is a data transmission system used by
FM stations in many countries. The unit can receive
various types of Radio Data System data, such as
“Program Service”, “Program Type,” “Radio Text” and
“Clock Time”, when it is tuned into a Radio Data System
broadcasting station.
■ Displaying Radio Data System
information
Note
“Program Service”, “Program Type”, “Radio Text”, and “Clock
Time” are not displayed if the radio station does not provide the
Radio Data System service.
■ Receiving traffic information
automatically (R-N303 only)
When “TUNER” is selected as the input source, the unit
automatically receives traffic information. To enable this
function, follow the procedure below to set the traffic
information station.
TUNER
NET
BLUETOOTH
TUNER
MEMORY
CLEAR
TUNING
BAND
PRESET
MEMORY
MODE
DISPLAY
CLEAR
DISPLAY
Cursor keys  / 
ENTER
ENTER
HOME
RETURN
SETUP
OPTION
TUNING
PRESET
MODE
DISPLAY
ENTER
HOME
RETURN
RETURN
NOW PLAYING
1
OPTION
VOLUME
MUTE
Tune in to the desired Radio Data System
broadcasting station.
Note
We recommend that you first register radio stations automatically
(p. 22) before tuning in to Radio Data System broadcasting
stations.
2
OPTION
SETUP
VOLUME
Press DISPLAY.
Each time you press the key, the displayed item changes.
STEREO SP A
TUNED
INFO
Program Type
Item name
About 3 seconds later, the corresponding information
for the displayed item appears.
NOW PLAYING
MUTE
1
When “TUNER” is selected as the input
source, press OPTION.
2
Use the cursor keys ( / ) to select
“TrafficProgram” and press ENTER.
The traffic information station search will start in
5 seconds. Press ENTER again to start the search
immediately.
BASIC
OPERATION
BAND
Note
• To search upward/downward from the current frequency, press
the cursor keys (/) while “READY” is displayed.
• To cancel the search, press RETURN.
• Texts in parentheses denote indicators on the front display.
The following screen appears for about 3 seconds
when the search finishes.
FINISH
TP
FM101.30MHz
TUNED
108.00
CLASSICS
Information
Program Service
Program service name
Program Type
Current program type
Radio Text
Information on the current program
Clock Time
Current time
Frequency
Frequency
Traffic information station (frequency)
Note
“TP Not Found” appears for about 3 seconds when no traffic
information stations are found.
25 En
English
STEREO SP A
TUNED
Listening to DAB radio (R-N303D)
DAB (Digital Audio Broadcasting) uses digital signals for clearer sound and more stable reception compared to analog
signals. This unit can also receive DAB+ (an upgraded version of DAB) that allows for more stations using MPEG-4
audio codec (AAC+), which has a more efficient transmission method.
Note
This unit supports Band III (174 to 240 MHz) only.
Preparing the DAB tuning
Before tuning in to DAB stations, an initial scan must be
performed. When you select the DAB for the first time,
the initial scan is performed automatically.
To listen to a DAB station, connect the antenna as
described in “Connecting the DAB/FM antenna (RN303D)” (p. 12).
Selecting a DAB radio station for
reception
You can select a DAB radio station from the stations
stored by the initial scan.
DIMMER
SLEEP
A
B
SPEAKERS
DIMMER
SLEEP
A
B
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
LINE 3
TUNER
NET
BLUETOOTH
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
LINE 3
TUNER
NET
BLUETOOTH
TUNER
BAND
TUNING
BAND
MEMORY
TUNER
BAND
TUNING
BAND
MEMORY
CLEAR
MODE
DISPLAY
PRESET
MODE
DISPLAY
1
Press TUNER to select “TUNER” as the input
source.
2
Press BAND to select the DAB band.
The initial scan starts. During the scan, the progress is
displayed on the front panel display.
When the scan is complete, the top of the list of the
scanned stations appears on the front panel display.
Note
• If no DAB radio stations are found by an initial scan,
“Not Found” will appear on the front panel display,
followed by “Off Air”. Press BAND twice to re-select the
DAB band and scan again.
• You can check reception strength of each DAB channel
label (p. 29).
• To perform an initial scan again after some DAB radio
stations are stored, select “Initiate Scan” (p. 37) in the
“OPTION” menu. If you perform an initial scan again, the
DAB radio stations currently registered to the preset
numbers will be cleared.
26 En
CLEAR
TUNING jj / ii
PRESET
1
Press TUNER to select “TUNER” as the input
source.
2
3
Press BAND to select the DAB band.
Press TUNING jj / ii to select a DAB radio
station.
DAB
BBC Radio 4
Note
• “Off Air” appears when the selected DAB radio station is
currently not available.
• When the unit is receiving a secondary station, “2” appears next
to “DAB”.
Listening to DAB radio (R-N303D)
3
Using preset function
You can register up to 40 DAB radio stations as presets.
Once you have registered stations, you can easily tune in
to them by recalling the presets.
Note
You can register up to 40 favorite radio stations each for DAB
and FM bands.
DIMMER
Press PRESET j / i to select the preset
number to which the station will be
registered.
When you select a preset number to which no station
is registered, the message “Empty” is displayed.
When you select a preset number to which a station
has already been registered, the message
“Overwrite?” is displayed.
MEMORY
02: Empty
SLEEP
A
“Empty” (not in use) or “Overwrite?” (in use)
B
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
LINE 3
TUNER
NET
BLUETOOTH
4
TUNER
BAND
Press MEMORY.
When registration is complete, the display returns to
the original state.
TUNING
BAND
PRESET
MEMORY
CLEAR
MODE
PRESET j / i
DISPLAY
CLEAR
To cancel registration, press RETURN or do not perform any
operations for about 30 seconds.
■ Recalling a preset station
Cursor keys  / 
ENTER
Tune in to a registered DAB radio station by selecting its
preset number.
ENTER
HOME
RETURN
1
Press TUNER to select “TUNER” as the input
source.
2
3
Press BAND to select the DAB band.
RETURN
SETUP
OPTION
OPTION
VOLUME
NOW PLAYING
MUTE
■ Registering a DAB radio station
Select a DAB radio station and register it to a preset
number.
2
Tune in to the desired DAB radio station. See
“Selecting a DAB radio station for reception”
(p. 26).
Press MEMORY.
Note
Press PRESET j / i to select the desired DAB
radio station.
DAB
PRESET:01
Note
• Preset numbers to which no stations are registered are
skipped.
• If this unit does not have any preset stations, “No Presets”
is displayed.
By holding down MEMORY for more than 3 seconds, you
can skip the following steps and automatically register the
selected station to an empty preset number (i.e., the preset
number following the last preset number used).
English
1
BASIC
OPERATION
Note
MEMORY
27 En
Listening to DAB radio (R-N303D)
■ Clearing preset DAB radio stations
1
Press TUNER to select “TUNER” as the input
source.
2
3
Tune in to the desired DAB radio station.
Clear DAB radio stations registered to the preset numbers.
1
Press TUNER to select “TUNER” as the input
source.
2
3
Press BAND to select the DAB band.
4
Press OPTION to enter the “OPTION” menu.
The “OPTION” menu for TUNER is displayed
(p. 37).
Use the cursor keys ( / ) to select “Clear
Preset”, and then press ENTER.
5
Select the desired preset station number by
using the cursor keys ( / ) repeatedly.
The selected preset number blinks on the front panel
display.
6
Press ENTER again to confirm.
“Cleared” is displayed on the front panel display.
Then, another preset station is shown on the front
panel display. When there is no more preset station,
“No Presets” is displayed, and then the display
returns to the “OPTION” menu.
To return the display to the original state, press
RETURN.
You can also use the following steps to cancel registration
of a station.
1
Press TUNER to select “TUNER” as the input
source.
2
3
Press CLEAR.
Use the PRESET j / i to select a preset
station to be cleared and press CLEAR.
If the preset station is cleared, “Cleared” appears.
Press DISPLAY.
Each time you press the key, the displayed item
changes.
INFO
Program Type
Item name
The selected item followed by a short description
appears, and then the corresponding information for
that item appears.
DAB
Sport
Information
Choice
Description
Service Label
Station name
DLS
(Dynamic Label Segment)
Information on the current station
Ensemble Label
Ensemble name
Program Type
Station genre
Date And Time
Current date and time
Audio Mode
Audio mode (monaural/stereo)
and bit rate
CH Label/Freq.
Channel label and frequency
Signal Quality
Signal reception quality
(0 [none] to 100 [best])
Displaying the DAB information
Note
This unit can receive various types of DAB information
when it is tuned in to a DAB radio station.
BAND
TUNING
MEMORY
CLEAR
PRESET
MODE
DISPLAY
DISPLAY
ENTER
HOME
RETURN
SETUP
OPTION
VOLUME
NOW PLAYING
28 En
MUTE
Some information may not be available depending on the selected
DAB radio station.
Listening to DAB radio (R-N303D)
Checking reception strength of each
DAB channel label
You can check reception strength of each DAB channel
label (0 [none] to 100 [best]).
COAXIAL
Frequency
Channel
label
174.928 MHz
5A
208.064 MHz
9D
176.640 MHz
5B
209.936 MHz
10A
178.352 MHz
5C
211.648 MHz
10B
180.064 MHz
5D
213.360 MHz
10C
181.936 MHz
6A
215.072 MHz
10D
183.648 MHz
6B
216.928 MHz
11A
185.360 MHz
6C
218.640 MHz
11B
187.072 MHz
6D
220.352 MHz
11C
188.928 MHz
7A
222.064 MHz
11D
CD
LINE 1
LINE 2
LINE 3
TUNER
NET
BLUETOOTH
TUNER
BAND
TUNING
BAND
MEMORY
Cursor keys  / 
ENTER
Channel
label
B
SPEAKERS
CLEAR
Frequency
SLEEP
A
OPTICAL
This unit supports Band III (174 to 240 MHz) only.
PRESET
MODE
DISPLAY
ENTER
190.640 MHz
7B
223.936 MHz
12A
192.352 MHz
7C
225.648 MHz
12B
194.064 MHz
7D
227.360 MHz
12C
195.936 MHz
8A
229.072 MHz
12D
197.648 MHz
8B
230.784 MHz
13A
HOME
RETURN
199.360 MHz
8C
232.496 MHz
13B
SETUP
OPTION
201.072 MHz
8D
234.208 MHz
13C
202.928 MHz
9A
235.776 MHz
13D
OPTION
VOLUME
NOW PLAYING
MUTE
1
Press TUNER to select “TUNER” as the input
source.
2
3
Press BAND to select the DAB band.
4
Use the cursor keys ( / ) to select
“Tune Aid”, and then press ENTER.
5
Use the cursor keys ( / ) to select the
desired DAB channel label.
204.640 MHz
9B
237.488 MHz
13E
206.352 MHz
9C
239.200 MHz
13F
BASIC
OPERATION
DIMMER
■ DAB frequency information
Press OPTION to enter the “OPTION” menu.
The “OPTION” menu for TUNER is displayed
(p. 37).
TUNE AID
12B
Level: 80
Reception strength
English
DAB channel label
29 En
Playing back music via Bluetooth
You can play back music files stored on a Bluetooth
device (such as mobile device) on the unit.
Please also refer to the owner’s manual of your Bluetooth
device.
This unit
Bluetooth device
(such as mobile device)
3
On the Bluetooth device, select the unit’s
model name from the available device list.
After pairing has been completed and the unit is
connected to the Bluetooth device, “Connected”
appears on the front display, and Bluetooth indicator
will light up.
BT
SP A
Wi Fi
Connected
BLUETOOTH
Note
• To use the Bluetooth function, set “Bluetooth” (p. 41) in the
“SETUP” menu to “On”.
• A Bluetooth device may not be detected by the unit or some
feature may not be compatible, depending on the model.
• You can transmit audio to Bluetooth speakers or headphones
using the MusicCast CONTROLLER app. The audio output can
only be selected from the MusicCast CONTROLLER app.
Connecting a Bluetooth device
(pairing)
Before you can connect a Bluetooth device to the unit for
the first time, a pairing operation is required. Pairing is an
operation that registers the Bluetooth devices with each
other beforehand. Once pairing has been completed,
subsequent reconnection will be easy even after the
Bluetooth connection is disconnected.
Note
• If the pass key is required, enter the number “0000”.
• You can change the network device name of this unit that will
be displayed when connecting Bluetooth devices, from
“Network Name” (p. 41) on the settings menu.
Playing back Bluetooth device
contents
Connect a paired Bluetooth device and start playback.
Check the following beforehand:
• Pairing has been completed.
• Bluetooth function on the Bluetooth device is turned on.
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
BLUETOOTH
BAND
TUNING
MEMORY
DIMMER
PRESET
SLEEP
CLEAR
A
MODE
DISPLAY
B
SPEAKERS
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
Playback keys
REPEAT
SHUFFLE
BLUETOOTH
BAND
MEMORY
1
2
TUNING
PRESET
Press BLUETOOTH to select “Bluetooth” as
the input source.
If another Bluetooth device is already connected,
disconnect the Bluetooth connection before you
perform a pairing operation.
Turn on the Bluetooth function of the
Bluetooth device.
30 En
1
Press BLUETOOTH to select “Bluetooth” as
the input source.
Note
If the unit detects the Bluetooth device previously connected, the
unit automatically connects to the Bluetooth device after Step 1.
To establish another Bluetooth connection, first disconnect the
current Bluetooth connection.
Playing back music via Bluetooth
2
Operate the Bluetooth device to establish a
Bluetooth connection.
Select the unit’s model name from the Bluetooth
device list on your device.
When a connection is established, BLUETOOTH
indicator on the front display will light up.
Note
If you cannot connect the Bluetooth device, please perform
pairing again (p. 30).
3
Operate the Bluetooth device to play back
music.
Note
You can use the playback keys on the remote control to control
playback.
Bluetooth
• Bluetooth is a technology for wireless communication
between devices within an area of about 10 meters (33 ft)
employing the 2.4 GHz frequency band, a band which can
be used without a license.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is
a radio band shared by many types of equipment. While
Bluetooth compatible devices use a technology minimizing
the influence of other components using the same radio
band, such influence may reduce the speed or distance of
communications and in some cases interrupt
communications.
• The speed of signal transfer and the distance at which
communication is possible differs according to the distance
between the communicating devices, the presence of
obstacles, radio wave conditions and the type of equipment.
• Yamaha does not guarantee all wireless connections
between this unit and devices compatible with Bluetooth
function.
BASIC
OPERATION
Disconnecting a Bluetooth
connection
English
Follow one of the procedures below to disconnect a
Bluetooth connection.
• Turn off the Bluetooth function on the Bluetooth
device.
• Hold down BLUETOOTH on the remote control for at
least 3 seconds.
• Set the input on this unit to anything except for
“Bluetooth”.
31 En
Playing back music stored on media servers (PCs/NAS)
You can play back music files stored on your PC or
DLNA-compatible NAS on the unit.
3
Click “Turn on media streaming”.
4
Select “Allowed” from the drop-down list
next to the unit’s model name.
NAS
This unit
PC
Note
• To use this function, the unit and your PC/NAS must be
connected to the same router (p. 13). You can check whether the
network parameters (such as the IP address) are properly assigned
to the unit in “Information” (p. 40) in the “SETUP” menu.
• To play back music files, the server software installed on the
PC/NAS must support the music file formats that you want to
play back.
• The audio may be interrupted while using the wireless network
connection. In this case, use the wired network connection.
• You can connect up to 16 media servers to this unit.
• Refer to “Supported file formats” (p. 52) for information
regarding supported file formats.
R-N303
Setting the media sharing of music
files
To play back music files in your computer with this unit,
you need to make the media sharing setting between the
unit and computer (Windows Media Player 12 or later). In
here, setting with Windows Media Player in Windows 7 is
taken as an example.
5
As with Step 4, select “Allowed” from the
drop-down list next to devices (PCs or
mobile devices) which you want to use as the
media controllers.
■ When using Windows Media Player 12
6
Click “OK” to exit.
1
2
■ When using a PC or a NAS with other
DLNA server software installed
Start Windows Media Player 12 on your PC.
Select “Stream”, then “Turn on media
streaming...”.
(Example of English version)
The control panel window of your PC appears.
32 En
Refer to the instruction manual for the device or software
and configure the media sharing settings.
Playing back music stored on media servers (PCs/NAS)
Playback of PC music contents
Follow the procedure below to operate the PC music
contents and start playback.
Note
“_” (underscore) will be displayed for characters not supported
by the unit.
TUNER
NET
NET
BAND
Select a music file or folder.
ENTER
Starts playback if pressed while
content is selected. Moves down
one level if pressed while a folder
is selected.
RETURN
Moves up one level.
p/ e
Playback
keys
PRESET
CLEAR
MODE
Function
Cursor keys
BLUETOOTH
TUNING
MEMORY
Keys
Stops/resumes playback.
s
Stops playback.
b/w
Skips forward/backward.
f/a
DISPLAY
DISPLAY
Cursor keys
ENTER
Displays information about the
song that is playing.
RETURN
RETURN
Note
OPTION
OPTION
VOLUME
NOW PLAYING
MUTE
REPEAT
SHUFFLE
NOW PLAYING
■ Repeat/shuffle settings
Playback keys
You can configure the repeat/shuffle settings for the
playback of PC music content.
Press NET repeatedly to select “Server” as
the input source.
SERVER
NAS A
1
SP A
Use the cursor keys ( / ) to select a music
server and press ENTER.
Use the cursor keys to select an item and
press ENTER.
If a song is selected, playback starts and the playback
information is displayed.
SERVER
Song01
You can also use a DLNA-compatible Digital Media Controller
(DMC) to control playback. For details, see “DMC Control”
(p. 40) in the “SETUP” menu.
When the input source is “Server,” press
REPEAT or SHUFFLE on the playback key
repeatedly to select the playback method.
Playback
keys
REPEAT
Setting
• If playback of a music file selected from the unit is ongoing on
your PC, the playback information is displayed.
• You can register the current playback song as a preset (p. 36).
• If you press the DISPLAY repeatedly, you can switch the
playback information on the front display (p. 20).
Use the following remote control keys to control
playback.
Function
Off
Turns off the repeat function.
One
Plays back the current song
repeatedly.
All
Plays back all songs in the current
album (folder) repeatedly.
Off
Turns off the shuffle function.
On
Plays back songs in the current album
(folder) in random order.
SHUFFLE
SP A
Note
BASIC
OPERATION
SETUP
3
NOW PLAYING
■ Automatic playback settings
Use these settings to choose whether to automatically play
back music from your PC or from the server when turning
on the unit or when switching between inputs.
1
2
Press OPTION.
Use the cursor keys ( / ) to select “Auto
Playback”, and press ENTER.
3
Turn Auto Playback ON or OFF using the
cursor keys ( / ).
4
Press OPTION when you are finished.
33 En
English
HOME
2
Displays the root directory of the
music server.
ENTER
HOME
1
HOME
Listening to Internet radio
You can listen to Internet radio stations from all over the world.
2
Note
• To use this function, the unit must be connected to the Internet
(p. 13). You can check whether the network parameters (such as
the IP address) are properly assigned to the unit in
“Information” (p. 40) in the “SETUP” menu.
• You may not be able to receive some Internet radio stations.
• This unit uses the “airable.Radio” service. airable is a service of
Tune In GmbH.
• This service may be discontinued without notice.
• Folder names may differ, depending on the language.
NET
OPTICAL
COAXIAL
CD
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
BAND
NetRadio
JazzST
Keys
PRESET
MODE
Function
Cursor keys
Select the Internet radio station or
category such as the genre.
ENTER
Starts playback if pressed while
an Internet radio station is
selected. Moves down one level if
pressed while a category is
selected.
RETURN
Moves up one level.
DISPLAY
DISPLAY
Cursor keys
ENTER
Playback keys
ENTER
HOME
OPTION
VOLUME
NOW PLAYING
MUTE
REPEAT
SHUFFLE
Stops playback.
Displays the top categories if
pressed during playback.
NOW PLAYING
Displays the playback
information for the Internet radio
station.
RETURN
SETUP
s
HOME
RETURN
HOME
SP A
Use the following remote control keys to control
playback.
TUNING
MEMORY
CLEAR
Use the cursor keys to select an item and
press ENTER.
If an Internet radio station is selected, playback starts
and the playback information is displayed.
NOW PLAYING
Note
Playback keys
1
Press NET repeatedly to select “NetRadio”
as the input source.
The station list appears on the front display.
NetRadio
Radios
34 En
SP A
• You can register the current playback station as a preset (p. 36).
• If you press the DISPLAY repeatedly, you can switch the
playback information on the front display (p. 20).
• Some information may not be available depending on the
station.
Playing back music with AirPlay
Playing back music with AirPlay
PC
iTunes
Router
This unit
iPhone/iPad/
iPod touch
Playback starts
Note
To use this function, the unit and your PC or iPhone must be
connected to the same router (p. 13). You can check whether the
network parameters (such as the IP address) are properly assigned
to the unit in “Information” (p. 40) in the “SETUP” menu.
AirPlay works with iPhone, iPad, and iPod touch with iOS
4.3.3 or later, Mac with OS X Mountain Lion or later, and PC
with iTunes 10.2.2 or later.
(as of June 2017)
Note
• If you press the DISPLAY repeatedly, you can switch the
playback information on the front display (p. 20).
• You can turn on the unit automatically when starting playback
on iTunes or iPhone by setting “Standby (Network Standby)”
(p. 41) in the “SETUP” menu to “On” or “Auto”.
• You can edit the network name (the unit’s name on the network)
displayed on iTunes/iPhone in “Network Name” (p. 41) in the
“SETUP” menu.
• You can adjust the unit’s volume from the iTunes/iPhone during
playback.
CAUTION
Using iTunes or an iPhone to adjust the volume may make
the volume unexpectedly loud, which could result in
damage to your hearing or to the device. Stop playback
immediately on iTunes or on your iPod if the playback
volume is too loud. We recommend that you use the
“Vol.Interlock (Volume interlock)” (p. 38) on the Option
menu to limit the changes in volume from iTunes or your
iPhone beforehand.
Use the following remote control keys to control
playback.
Keys
Playback of iTunes/iPhone music
contents
Follow the procedure below to play back iTunes/iPhone
music contents on the unit.
1
Turn on the unit, and start iTunes on the PC
or display the playback screen on the
iPhone.
If the iTunes/iPhone recognizes the unit, the AirPlay
icon appears.
iOS 10 (example)
Functions
p/ e
s
Playback
keys
BASIC
OPERATION
The AirPlay function allows you to play back iPhone/
iPad/iPod touch/iTunes music on the unit via network.
Stops/resumes playback.
Stops playback.
b/w
Skips forward/backward.
f/a
REPEAT
Changes the Repeat settings.
SHUFFLE
Changes the Shuffle settings.
iTunes (example)
Note
If the icon does not appear, check whether the unit and PC/iPhone
are connected to the router properly.
On the iTunes/iPhone, click (tap) the AirPlay
icon and select the unit (network name of the
unit) as the audio output device.
English
2
3 Select a song and start playback.
The unit automatically selects “AirPlay” as the input
source and starts playback. The playback information is
displayed on the front display.
35 En
Registering the current playback song/station (Preset function)
When you select a network source as the input source, you
can register the current playback song or streaming station
as a preset. You can program up to 40 such presets.
You can then easily recall any preset song/station by
selecting its preset number.
The following input sources can be set as presets.
Server, Net Radio, Bluetooth and streaming services.
3
Note
To cancel registration, press RETURN.
Recalling a preset
1
Select NET or BLUETOOTH as the input
source.
2
Press PRESET j / i to select a preset
number.
3
Press ENTER to recall preset.
Note
• Only the input source will be registered for “Bluetooth”.
Individual songs cannot be registered.
• Using the MusicCast CONTROLLER app (p. 19) enables you
to register contents (songs, radio broadcast stations) and listen
to them.
• When you register music files stored on a PC/NAS, this unit
memorizes the relative position of the music files in the folder.
If you have added or deleted any music files to or from the
folder, this unit may not recall the music file correctly. In such
cases, register the items again.
NET
LINE 1
LINE 2
PHONO
TUNER
NET
BLUETOOTH
BAND
PRESET
MEMORY
CLEAR
MODE
PRESET j / i
DISPLAY
CLEAR
Cursor keys  / 
ENTER
ENTER
1
Playback a song or streaming station you
want to register.
2
Hold down MEMORY for more than 3
seconds.
The first time you register a song/station, you will be
prompted to register the selected song/station to
preset number “01”. You will be also prompted to
register each additional song/station you select to the
next available preset number.
SP A
Preset number
Note
To select a preset number for registering, press PRESET j / i or
the cursor keys (/).
36 En
1
Select NET or BLUETOOTH as the input
source.
2
Press PRESET j / i to select a preset
number.
3
Press CLEAR to clear the preset.
If the preset station is cleared, “Empty” appears.
Registering to a preset
MEMORY
01: Empty
Note
• A few seconds after you select the preset number, playback of
the selected preset will start.
• To cancel recalling preset, press RETURN.
Clearing a preset
TUNING
MEMORY
Press MEMORY again to register preset.
ADVANCED OPERATION
Configuring playback settings for different playback sources
(OPTION menu)
You can configure separate playback settings for different playback sources. This menu allows you to easily configure
settings during playback.
CLEAR
MODE
OPTION menu items
DISPLAY
Note
Cursor keys
ENTER
ENTER
Available items vary depending on the selected input source.
Item
RETURN
RETURN
OPTION
OPTION
VOLUME
NOW PLAYING
1
Press OPTION.
OPTION
Volume Trim
Use the cursor keys to select an item and
press ENTER.
Note
To return to the previous state during menu operations, press
RETURN.
3
4
Volume Trim
Corrects volume differences between
input sources.
37
Signal Info.
Displays information about the audio
signal.
38
Auto Preset
Automatically registers FM radio
stations with strong signals as presets.
22
Clear Preset
Clear radio stations registered to preset
24, 28
numbers.
Initiate Scan*1
Performs an initial scan for DAB radio
reception.
26
Tune Aid*1
Checks reception strength of each
DAB station.
29
TrafficProgram*2
Automatically searches for a traffic
information station.
25
Vol.Interlock
Enables/Disables volume controls from
iTunes/iPhone via AirPlay.
38
Auto Playback
Use these settings to choose whether to
automatically play back music from
your PC or from the server when
turning on the unit or when switching
between inputs.
33
MUTE
SP A
2
Page
Use the cursor keys ( / ) to select a
setting.
To exit from the menu, press OPTION.
ADVANCED
OPERATION
SETUP
Function
*1 Only for R-N303D
*2 Only for R-N303 UK and Europe models
■ Volume Trim
Corrects volume differences between input sources. If you
are bothered by volume differences when switching
between input sources, use this function to correct it.
Note
This setting is applied separately to each input source.
Setting range
–10 to +10 (increments of 1)
English
HOME
Default
0
37 En
Configuring playback settings for different playback sources (OPTION menu)
■ Signal Info.
Displays information about audio signal.
Choices
FORMAT
Audio format of the input signal
SAMPLING
The number of samples per second of the input
digital signal
Note
To switch the information on the front display, press the cursor
keys (/) repeatedly.
■ Vol.Interlock (Volume interlock)
Enables/disables volume controls from iTunes/iPhone via
AirPlay.
Settings
Off
Disables volume controls from iTunes/iPhone.
Ltd
(default)
Enables volume controls from iTunes/iPhone
within the limited range (1 to 60 and mute).
Full
Enables volume controls from iTunes/iPhone in
the full range.
38 En
Configuring various functions (SETUP menu)
Configuring various functions (SETUP menu)
You can configure the unit’s various functions.
CLEAR
Cursor keys
ENTER
MODE
1
SETUP
Network
DISPLAY
2
ENTER
HOME
RETURN
SETUP
OPTION
RETURN
SETUP
SP A
Use the cursor keys ( / ) to select and
press ENTER.
SP A
SETUP
Max Volume
VOLUME
NOW PLAYING
Press SETUP.
MUTE
3
Use the cursor keys ( / ) to select a
setting and press ENTER.
MAX VOL
MAX
SP A
Note
To return to the previous state during menu operations, press
RETURN.
4
Exit from the menu, press SETUP.
Function
Page
Connection
Selects the network connection method.
40
Information
Displays the network information on the unit.
40
IP Address
Configures the network parameters (such as IP address).
40
DMC Control
Selects whether to allow a DLNA-compatible Digital Media Controller (DMC) to
control playback.
40
Standby
(Network Standby)
Selects whether to enable/disable the function that turns on the unit from other
network devices.
41
Network Name
Edits the network name (the unit’s name on the network) displayed on other network
devices.
41
Update
(Network Update)
Updates the firmware via the Internet.
41
On/Off
Enables/disables the Bluetooth functions.
41
Standby
(Bluetooth Standby)
Selects whether to enable/disable the function that turns on the unit from Bluetooth
devices (Bluetooth standby).
41
Balance
Adjusts the sound output balance of the left and right speakers to compensate for
sound imbalances.
41
Max Volume
Sets the maximum volume to prevent excessive loudness.
41
InitialVolume
Sets the initial volume for when this receiver is turned on.
42
AutoPowerStby
(Auto Power Standby)
Enables/disables the auto-standby function.
42
Network
Bluetooth
39 En
English
Menu item
ADVANCED
OPERATION
SETUP menu items
Configuring various functions (SETUP menu)
Network
■ IP Address
Configures the network parameters (such as IP address).
Configures the network settings.
■ Connection
DHCP
Select whether to use a DHCP server.
Selects the network connection method.
Wired
Select this option when you want to connect
the unit to a network with a commerciallyavailable network cable (p. 13).
Wireless
Select this option when you want to connect
the unit to a network via the wireless router or
access point (p. 15, 16, 16).
W.Direct
(Wireless
Direct)
Select this option when you want to connect a
mobile device to the unit directly. For details
on settings, see “Connecting a mobile device
to the unit directly (Wireless Direct)” (p. 17).
Note
If the unit is operating in MusicCast Extend mode, “Extend” will
be displayed. For details on Extend mode, see the MusicCast
Setup Guide on the Yamaha website.
Off
Does not use a DHCP server. Configure the
network parameters manually. For details, see
“Manual network settings” below.
On (default)
Uses a DHCP server to automatically obtain the
unit’s network parameters (such as IP address).
Manual network settings
1
2
Set “DHCP” to “Off”.
Use the cursor keys ( / ) to select a
parameter type.
IP
Specifies an IP address.
SUBNET
Specifies a subnet mask.
GATEWAY
Specifies the IP address of the default gateway.
DNS P
Specifies the IP address of the primary DNS
server.
DNS S
Specifies the IP address of the secondary DNS
server.
■ Information
Displays the network information on the unit.
NEW FW
Appears if an update for this unit’s firmware is
available (p. 45).
STATUS
The connection status of the network.
Use the cursor keys ( / ) to select the edit
position.
MC NET
Status of the MusicCast Network. If “Ready”
appears, you can use the MusicCast
CONTROLLER app.
IP
MAC
Displays MAC address of the unit. MAC
address will vary depending on the connection
method (wired LAN connection or wireless
LAN / Wireless Direct connection).
SSID
(When using wireless LAN connection or
Wireless Direct) The SSID of this unit on the
wireless network.
4
Use the Cursor keys ( / ) to change a
value.
IP
IP address
5
To exit from the menu, press SETUP.
SUBNET
Subnet mask
GATEWAY
The IP address of the default gateway
DNS P
The IP address of the primary DNS server
DNS S
The IP address of the secondary DNS server
3
SP A
Address1••192›
(Example: IP address setting)
Use the cursor keys (/) to switch between
segments (Address1, Address2...) of the address.
■ DMC Control
Selects whether to allow DLNA-compatible Digital Media
Controller (DMC) to control playback.
Disable
Does not allow DMCs to control playback.
Enable
(default)
Allows DMCs to control playback.
Note
A Digital Media Controller (DMC) is a device that can control
other network devices through the network. When this function is
enabled, you can control playback of the unit from DMCs (such
as Windows Media Player 12) on the same network.
40 En
Configuring various functions (SETUP menu)
■ Standby (Network Standby)
Selects whether the unit can be turned on from other
network devices (network standby).
Bluetooth
Configures the Bluetooth settings.
Off
Disables the network standby function.
■ On/Off
Enables/disables the Bluetooth function (p. 30).
On
Enables the network standby function.
(The unit consumes more power than when “Off”
is selected.)
Auto
(default)
Enables the network standby function. The unit
enters power-saving mode eight hours after it is
disconnected from the network.
Off
Disables the Bluetooth function.
On (default)
Enables the Bluetooth function. Immediately
after selecting the “On”, output of the network
source is paused.
■ Standby (Bluetooth Standby)
■ Network Name
Edits the network name (the unit’s name on the network)
displayed on other network devices.
1
Select “Network Name”.
For information on selecting a menu option, refer to
the steps described on page 39.
R-N303 (example)
SP A
NET NAME
R-N303 XXXXXX
2
Press ENTER to enter the name edit display.
R-N303 (example)
SP A
NET NAME
R-N303 XXXXXX›
3
4
5
Use the cursor keys ( / ) to select a
character and ( / ) to move the edit
position.
You can insert / delete a character, by pressing
PRESET i (insert) or PRESET j (delete).
To confirm the new name, press ENTER.
To exit from the menu, press SETUP.
Off
Disables the Bluetooth standby function.
On (default)
Enables the Bluetooth standby function. (The
unit consumes more power than when “Off” is
selected.)
Note
This setting is not available when “Standby (Network Standby)”
(p. 41) is set to “Off”.
Balance
Adjusting the sound output balance of the left and right
speakers to compensate for sound imbalance caused by
speaker locations or listening room condition.
Setting range
L+10 to R+10
ADVANCED
OPERATION
With an advanced energy saving design, this product achieves
a low power consumption of not more than two watts when in
Network Standby mode.
Selects whether to enable/disable the function that turns
on the unit from Bluetooth devices (Bluetooth standby). If
this function is set to “On”, the unit automatically turns on
when a connect operation is performed on the Bluetooth
device.
Default
Center
Max Volume
Sets the maximum volume to prevent excessive loudness.
Setting range
1 to 99 (1step increments), Max
Default
Max
English
■ Update (Network Update)
Updates the firmware via the network.
Perform
Update
Starts the process to update the unit’s firmware.
For details, see “Updating the unit’s firmware”
(p. 45).
Version
Displays the version of the firmware installed on
the unit.
ID
Displays the system ID number.
41 En
Configuring various functions (SETUP menu)
InitialVolume
Sets the initial volume when the receiver is turned on.
Setting range
Off, Mute, 1 to 99 (1step increments), Max
Default
Off
AutoPowerStby
(Auto Power Standby)
Enables/disables the auto-standby function. If you do not
operate the unit for the specified time, the unit will
automatically go into standby mode.
Off
Does not set the unit to standby mode
automatically.
On
Sets the unit to standby mode automatically.
While NET or BLUETOOTH is selected as the
input source, the unit will switch to standby mode
if the selected source is not played back for 20
minutes.
For all input sources, the unit will switch to
standby mode if it is not operated for 8 hours.
Default
U.K. and Europe models: On
Other models: Off
Note
Just before the unit enters standby mode, “AutoPowerStby”
appears and then countdown starts in the front display.
42 En
Configuring the system settings (ADVANCED SETUP menu)
Configuring the system settings (ADVANCED SETUP menu)
Configure the system settings of the unit while viewing the front display. The ADVANCED SETUP menu can be
operated from the front panel.
1
2
Checking the firmware version
(VERSION)
Press A (power) to turn off the unit.
While holding down RETURN on the front
panel, press A (power).
Check the version of firmware currently installed on the
unit.
RETURN
Note
MODE
MEMORY
BAND
PRESET
• You can also check the firmware version in “Update (Network
Update)” (p. 41) in the “SETUP” menu.
• It may take a while until the firmware version is displayed.
TUNING
VOLUME
SELECT
BASS
PHONES
TREBLE
INPUT
PUSH
ENTER
SPEAKERS
RETURN
CONNECT
A (power)
3
4
5
DISPLAY
Selecting the remote control ID
(REMOTE ID)
SELECT/ENTER
Rotate SELECT/ENTER to select an item.
Press SELECT/ENTER to select a setting.
Press A (power) to set the unit to turn off and
turn it on again.
The new settings take effect.
ADVANCED SETUP menu items
Item
Function
This changes the remote control ID on the unit.
Normally, this should be set to “ID1”. When operating the
unit using remote controllers included with certain
Yamaha players, set this to “AUTO”.
Settings
ID1 (default), AUTO
Setting tuner frequency step (TU)
Page
Selects the step size for locating tuner frequencies.
(Only for Asia and General models)
VERSION
Checks the version of firmware
currently installed on the unit.
43
REMOTE ID
Selects the unit’s remote control ID.
43
TU*
Sets tuner frequency step.
43
INIT
Restores the default settings.
43
Restoring the default settings (INIT)
UPDATE
Updates the firmware.
44
Restores the default settings for the unit.
Choices
CANCEL
(default)
Does not perform an initialization.
NETWORK
Initializes all of the network and Bluetooth
settings. If you initialize the unit, all presets for
the network input sources (p. 36) will be cleared.
ALL
Restores the default settings for the unit.
English
* Only for Asia and General models
Settings
FM100/AM10, FM50/AM9 (default)
ADVANCED
OPERATION
DISPLAY
43 En
Configuring the system settings (ADVANCED SETUP menu)
Updating the firmware (UPDATE)
New firmware that provides additional features or product
improvements will be released as needed. If the unit is
connected to the Internet, you can download the firmware
via the network. For details, refer to the information
supplied with updates.
■ Firmware update procedure
Do not perform this procedure unless firmware update is
necessary. Also, make sure you read the information
supplied with updates before updating the firmware.
1
Press DISPLAY to start firmware update.
Note
You can also update the unit’s firmware by following the
procedure in “Updating the unit’s firmware” (p. 45).
44 En
Updating the unit’s firmware
Updating the unit’s firmware
New firmware that provides additional features or product improvements will be released as needed. If the unit is
connected to the Internet, you can download the firmware via the network and update it.
Notice
• Do not operate the unit or disconnect the power cord or network cable during firmware update. Firmware update takes about 5
minutes or more (depending on your Internet connection speed).
• If the unit is connected to the wireless network via a wireless network adapter, network update may not be possible depending on
the condition of the wireless connection.
Note
Updates can also be performed from the ADVANCED SETUP menu (p. 44).
7
CLEAR
MODE
DISPLAY
If “UPDATE SUCCESS” appears on the front
display, press A (power) on the front panel.
The firmware update is complete.
Cursor keys  / 
ENTER
ENTER
HOME
■ Notification of new firmware update
RETURN
RETURN
SETUP
SETUP
OPTION
When new firmware is available, “NEW FW Update” will
be displayed for a short period of time when the unit is
turned on.
VOLUME
MUTE
1
2
Press SETUP.
3
Use the cursor keys ( / ) to select
“Information” and press ENTER.
If new firmware is available, “NEW FW Available”
appears on the front display.
Use the cursor keys ( / ) to select
“Network” and press ENTER.
NEW FW
Update [ENTER]
To update the unit's firmware, press ENTER (as described
in Step 6 above) while this notification is displayed. If
“UPDATE SUCCESS” appears on the front display, press
A (power) on the front panel.
ADVANCED
OPERATION
NOW PLAYING
NEW FW
Available
4
5
Press RETURN to return the previous state.
Use the cursor keys ( / ) to select
“Update” and press ENTER.
UPDATE
PerformUpdate
To start the firmware update, press ENTER.
The unit restarts and the firmware update starts.
English
6
Note
To cancel the operation without updating the firmware, press
SETUP.
45 En
ADDITIONAL INFORMATION
Troubleshooting
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to standby mode, disconnect the power cord, and contact the nearest
authorized Yamaha dealer or service center.
■ General
Problem
See
page
Possible cause
Remedy
The protection circuitry has been activated
three times consecutively. If the unit is in
this state, the STANDBY/ON indicator on
the unit will blink when you try to turn on
the power.
As a safety precaution, capability to turn on the power
is disabled. Contact your nearest Yamaha dealer or
service center to request repair.
The power cord is not connected or the
plug is not completely inserted.
Connect the power cord firmly.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
10
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Turn off the power and turn it on again after at least
15 seconds elapse. (If the problem persists,
disconnect the power cord from the AC wall outlet
and plug it again.)
—
The power does not
turn off.
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Turn off the power and turn it on again after at least
15 seconds elapse. (If the problem persists,
disconnect the power cord from the AC wall outlet
and plug it again.)
—
No sound.
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
l / h on the front panel (or one of the input
selection key on the remote control).
20
A pair of headphones is connected to the
PHONES jack.
Unplug the headphones from the PHONES jack.
The SPEAKERS A/B switches are not set
properly.
Turn on the corresponding SPEAKERS A or
SPEAKERS B.
20
Speaker connections are not secure.
Secure the connections.
10
Output has been muted.
Turn off the mute.
9
The Max volume or Initial volume setting
is set too low.
Check the settings for “Max Volume” and “Initial
Volume” in the “SETUP” menu.
41
The component corresponding to the
selected input source is turned off or is not
playing.
Turn the component on and make sure it is playing.
The audio output of a device connected to
a digital audio input (COAXIAL/
OPTICAL jacks) is set to other than PCM.
Set the audio output of the connected device to PCM.
The power does not
turn on.
46 En
—
—
5
—
—
Troubleshooting
Problem
The sound suddenly
goes off.
Possible cause
Remedy
See
page
Set the speaker impedance to match your speakers.
11
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
11
This unit has become too hot.
Make sure the openings on the top panel are not
blocked.
—
The auto power standby function has
turned this unit off.
Change the auto power standby (“AutoPowerStby” in
the “SETUP” menu) to turn off.
42
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
Incorrect setting for the speaker balance.
Set the speaker balance (“Balance” in the “SETUP”
menu) to the appropriate setting.
41
There is a lack of bass
and no ambience.
The + and – wires are connected in
reverse at the amplifier or the speakers.
Connect the speaker wires to the correct + and –
phase.
11
A “humming” sound
can be heard.
Incorrect cable connections.
Connect the audio plugs firmly. If the problem
persists, the cables may be defective.
11
The sound is
degraded when
listening with the
headphones
connected to the CD
player or the tape
deck connected to
this unit.
The power of this unit is turned off, or this
unit is set to standby mode.
Turn on the power of this unit.
Only the speaker on
one side can be
heard.
The protection circuitry has been activated
because of a short circuit, etc.
—
The remote control
does not work nor
function properly.
Remedy
See
page
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
9
Possible cause
Wrong distance or angle.
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
The batteries are weak.
Replace all batteries.
—
9
■ FM reception
Problem
The FM radio
reception strength is
poor, and noise can
be heard.
The radio station
cannot be
automatically
selected.
Remedy
See
page
The unit is receiving radio interference,
such as multipath reflections.
Change the FM antenna height, direction, or place of
installation.
12
The unit is receiving in a region located
far away from the radio station.
Press the MODE button repeatedly on the remote
control (or on the front panel) to set “FM Mode” to
“Mono”.
22
Use a commercially-available outdoor antenna.
12
Use a commercially-available outdoor antenna.
12
Possible cause
The FM radio signal is weak.
Select the station manually.
22
47 En
English
Problem
ADDITIONAL
INFORMATION
■ Remote control
Troubleshooting
■ AM reception (R-N303)
Possible cause
Remedy
See
page
The AM radio
reception strength is
poor, and noise can
be heard.
The unit is picking up noise from sources
such as a fluorescent light or a motor.
In some environments, it may be difficult to
completely eliminate noise. However, using a
commercially-available outdoor antenna may help to
reduce noise.
12
The radio station
cannot be
automatically
selected.
The AM radio signal is weak.
Change the direction of the AM antenna.
12
Select the station manually.
22
Use a commercially-available outdoor antenna.
Connect the supplied AM antenna to the
ANTENNA(AM) jack.
12
Problem
AM radio stations
cannot be registered
(preset).
The stations may have been registered
automatically (Auto Preset).
Auto presets can be used with FM radio stations only.
AM radio stations must be manually registered.
23
■ DAB reception (R-N303D)
Problem
Cannot tune into any
DAB stations.
Possible cause
See
page
The initial scan operations were not
performed.
Perform the initial scan operations.
There is no DAB coverage in your area.
Check with your dealer or WorldDMB Online at
“http://www.worlddab.org” for a listing of the DAB
coverage in your area.
—
Change the height, direction, or placement of the
antenna.
12
Check with your dealer or WorldDMB Online at
“http://www.worlddab.org” for a listing of the DAB
coverage in your area.
—
The DAB signals are too weak.
The initial scan
operations are not
successful and “Not
Found” appears on
the front panel
display.
The DAB signals are too weak.
The DAB station
reception is weak.
The DAB signals are too weak.
There is noise
interference (e.g.
hiss, crackle, or jitter).
The antenna needs to be repositioned.
The DAB station
information does not
appear or is
inaccurate.
The DAB station may be temporarily out
of service, or the DAB station information
is not provided by the DAB broadcaster.
48 En
Remedy
There is no DAB coverage in your area.
26
Change the height, direction, or placement of the
antenna.
12
The DAB signals are too weak.
Contact the DAB broadcaster.
—
Troubleshooting
■ Bluetooth
No sound can be
heard, or the sound
cuts off intermittently.
Remedy
See
page
The “Bluetooth” setting in the settings
menu is “Off”.
Set the “Bluetooth” setting in the settings menu to
“On”.
41
The unit is connected to a different
Bluetooth device.
Unpair the Bluetooth device that is currently
connected, and pair with the desired Bluetooth
device.
30
The unit is too far away from the
Bluetooth device.
Move the Bluetooth device closer to this unit.
A device emitting electromagnetic waves
(such as a microwave oven, a wireless
device and so on) are located nearby.
Do not use this unit near devices that emit
electromagnetic waves.
The Bluetooth device you are using does
not support the A2DP protocol.
Use a Bluetooth device that supports the A2DP
protocol.
The connection profile registered in the
Bluetooth device is not functioning
correctly for some reason.
Delete the connection profile in the Bluetooth device,
and then connect the Bluetooth device to this unit.
30
The passkey on the Bluetooth adapter or
other device is set to a code besides
“0000”.
Use a Bluetooth device on which the passkey is set to
“0000”.
—
The volume on the Bluetooth device is too
low.
Raise the volume on the Bluetooth device.
The sound output on the Bluetooth device
is not set to this unit.
Select this unit as the output destination on the
Bluetooth device.
The connection to the Bluetooth device is
cut off.
Connect with the Bluetooth device one more time.
The unit is too far away from the
Bluetooth device.
Move the Bluetooth device near this unit.
A device emitting electromagnetic waves
(such as a microwave oven, a wireless
device and so on) is located nearby.
Do not use this unit near devices that emit
electromagnetic waves.
—
—
52
—
30
30
—
—
ADDITIONAL
INFORMATION
The unit cannot
connect to a
Bluetooth device.
Possible cause
English
Problem
49 En
Troubleshooting
■ Network
Problem
Possible cause
Remedy
See
page
The network function
cannot be used.
The network information (IP address) has
not been properly acquired.
Enable the DHCP server function on the router. In the
settings menu of this unit, set “DHCP” to “On".
When manually setting network information without
using a DHCP server, make sure that the IP address of
this unit is different from that of other devices on the
network.
40
The power on the wireless LAN router
(access point) is off.
Turn on the power of the wireless LAN router (access
point).
—
The unit is too far from the wireless LAN
router (access point).
Set up this unit closer to the wireless LAN router
(access point).
—
There is an object blocking the signal path
between this unit and the wireless LAN
router (access point).
Set up this unit so that there is a clear signal path
between this unit and the wireless LAN router (access
point).
—
A device emitting electromagnetic waves
(such as a microwave oven, a wireless
device and so on) may be located nearby.
When connecting wirelessly, do not use this unit near
devices that emit electromagnetic waves.
—
Access to the network is restricted, due to
a firewall on the wireless LAN router
(access point).
Check the firewall settings of the wireless LAN
router (access point).
—
The media sharing settings on the
computer (server) may be incorrect.
Change the media sharing settings so that this unit
can access the folder on the computer (server).
32
Access is restricted due to the security
settings on the computer (server) or router.
Check the security settings on the computer (server)
and router.
—
This unit and the computer (server) are
not connected to the same network.
Check the network and router settings, to make sure
that they are connected to the same network.
—
The files on the
computer (server)
cannot be displayed
(played back).
The file format may not be compatible
with this unit or with the computer
(server).
Use a file format that is compatible with this unit and
with the computer (server). See “Devices and File
Formats Supported” (p. 52) for a list of music files
supported by this unit.
52
Internet radio cannot
be played.
Service may be stopped on the currently
selected radio station.
Data may not be able to be received from the radio
station due to a network error, or service at the radio
station itself may be paused. Try playing back again
after a while, or select a different radio station.
—
The currently selected radio station is
broadcasting silence.
Some radio stations broadcast silence at some times
of the day. During these times, even though the
broadcast can be received, you will not hear anything.
Try playing back again after a while, or select a
different radio station.
—
Access to the network is restricted due to
the firewall settings on a network device,
such as a router.
Check the firewall settings. Note that Internet radio
can only be played back via the ports specified by the
radio station in question. The port numbers may
differ, depending on the radio station.
—
This unit cannot be
detected when using
AirPlay on an iPhone.
You may be using a router that supports
multiple SSIDs.
The network separator function on the router may be
preventing this unit from being accessed. When
connecting to this unit with an iPhone, use an SSID
on which this unit can be accessed (try connecting via
the primary SSID).
—
The unit is not
detected when using
a dedicated
application on a
mobile device.
This unit and the mobile device are not
connected to the same network.
Check the network and router settings, to make sure
that they are connected to the same network.
—
You may be using a router that supports
multiple SSIDs.
The network separator function on the router may be
preventing this unit from being accessed. When
connecting to this unit with an iPhone, use an SSID
on which this unit can be accessed (try connecting via
the primary SSID).
—
The unit cannot
connect to the
Internet via wireless
LAN router (access
point).
A wireless network
cannot be found.
The computer (server)
cannot be detected.
50 En
Troubleshooting
Problem
Possible cause
The firmware on this
unit failed to update
via the network.
The network connection may not be good.
The unit cannot
connect to the
Internet via wireless
LAN router (access
point).
MAC address filtering may have been
enabled on the wireless LAN router
(access point).
Remedy
See
page
Try connecting again after a while.
—
This unit cannot connect to the Internet while MAC
address filtering is enabled on the access point.
Change the settings on the wireless LAN router
(access point) to allow this unit to connect.
—
■ Messages on the front display
Message
Possible cause
Remedy
Access denied
Access to the PC is denied.
Configure the sharing settings and select the unit as a device to
which music contents are shared (p. 32).
Access error
There is a problem with the signal path
from the network to the unit.
Make sure your router and modem are turned on.
Check SP Wires
The speaker cables short circuit.
Twist the bare wires of the cables firmly and connect to the unit
and speakers properly.
No content
There are no playable files in the selected
folder.
Select a folder that contains files supported by the unit.
Please wait
The unit is preparing to connect to the
network.
Wait until the message disappears. If the message stays more than
3 minutes, turn off the unit and turn it on again.
Unable to play
The unit cannot play back the songs stored
on the PC for some reason.
Check if the format of files you are trying to play is supported by
the unit. For information about the formats supported by the unit,
see “Supported devices and file formats” below.
If the unit supports the file format, but still cannot play back any
files, the network may be overloaded with heavy traffic.
Version error
Firmware update via the Internet failed.
Update the firmware again.
English
ADDITIONAL
INFORMATION
Check the connection between the unit and your router (or hub)
(p. 13).
51 En
Supported devices and file formats
The following devices and file formats can be used by thisunit.
Supported devices
■ Bluetooth® devices
• This unit supports the A2DP audio profile.
• This unit supports the AVRCP control profile.
• Not all Bluetooth devices are guaranteed to work with this unit.
■ AirPlay
AirPlay works with iPhone, iPad, and iPod touch (iOS 4.3.3 or later), Mac OS X
Mountain Lion or later, and PCs with iTunes 10.2.2 or later.
Compatible devices
Made for:
iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone 5c, iPhone 5,
iPhone 4s
iPad Pro (9.7" and 12.9"), iPad mini 4, iPad Air 2, iPad mini 3, iPad Air, iPad mini 2, iPad mini, iPad (3rd and 4th
generation), iPad 2
iPod touch (5th and 6th generation)
(as of June 2017)
Supported file formats
PC (NAS)
File
Sampling frequency (kHz)
Quantization bitrate (bit)
Bitrate
Gapless playback
16/24
—
✔
WAV *
32/44.1/48/88.2/96/176.4/192
MP3
32/44.1/48
—
8 to 320
—
WMA
32/44.1/48
—
8 to 320
—
MPEG-4 AAC
32/44.1/48
—
8 to 320
—
FLAC
32/44.1/48/88.2/96/176.4/192
16/24
—
✔
ALAC
32/44.1/48/88.2/96
16/24
—
✔
AIFF
32/44.1/48/88.2/96/176.4/192
16/24
—
✔
DSD
2.8 MHz/5.6 MHz
1
—
—
* Linear PCM format only
Note
• To play back FLAC files stored on your PC/NAS, you need to install server software that supports sharing of FLAC files via DLNA
on your PC or use a NAS that supports FLAC files.
• Digital Rights Management (DRM) contents cannot be played back.
52 En
Specifications
Specifications
• PC client function
• Compatible with DLNA ver. 1.5
• AirPlay supported
• Internet radio
• Streaming service
• Wi-Fi function
Capable of direct connection with mobile device
Available security method
..................................... WEP, WPA2-PSK (AES), Mixed Mode
Radio frequency band ....................................................... 2.4 GHz
Radio Frequency (Operational Frequency)
............................................................. 2412 MHz to 2472 MHz
Maximum Output Power (E.I.R.P) ...............17.5 dBm (56.2 mW)
Wireless network standard................................ IEEE 802.11 b/g/n
Wi-Fi settings
WPS (Wifi Protected Setup) ............................. Capable of WPS
Capable of sharing with iOS devices by wireless connection.
Bluetooth related function
• Version ............................................................. Bluetooth 2.1 + EDR
• Frequency ............................................................................ 2.4 GHz
• Maximum input signal
CD, etc. (1 kHz, 0.5% THD)..................................................2.2 V
• Output level/output impedance
CD, etc. (input 1 kHz, 500 mV)
LINE OUT ......................................................... 500 mV/2.2 kΩ
PHONES (8Ω load).............................................. 470 mV/470Ω
• Frequency response
CD, etc. (20 Hz to 20 kHz) ...........................................0 ± 0.5 dB
CD, etc. (10 Hz to 100 kHz) .........................................0 ± 3.0 dB
• Total harmonic distortion
CD, etc. to SPEAKERS OUT
(20 Hz to 20 kHz, 50 W, 8Ω) ..................................0.2% or less
• Signal to noise ratio (IHF-A)
CD, etc. (input shorted, 500 mV).......................... 100 dB or more
• Residual noise (IHF-A) .......................................................... 70 µV
• Channel separation
CD, etc. (5.1 k input shorted, 1 kHz/10 kHz)
......................................................................... 65/50 dB or more
• Tone control characteristics
BASS
Boost/cut (50 Hz) ...........................................................± 10 dB
TREBLE
Boost/cut (20 kHz) .........................................................± 10 dB
• Maximum Output Power (E.I.R.P) ......................4.0 dBm (2.5 mW)
• Digital input (OPTICAL/COAXIAL)
Support audio sample rate
...... 32 kHz/44.1 kHz/48 kHz/88.2 kHz/96 kHz/176.4 kHz/192 kHz
• Wireless Output ....................................................Bluetooth Class 2
FM
• Profiles
Source function
The unit  Sink Device (ex. Bluetooth Headphone)
Profile: A2DP version1.3, AVRCP version1.6
CODEC: SBC
Sink function
The unit  Source device (ex. iPhone/Android)
Profile: A2DP Version1.3, AVRCP version1.6
CODEC: SBC, AAC
• Tuning range
[North America model] ................................... 87.5 to 107.9 MHz
[General and Asia models]
....................................87.5 to 107.9 MHz/87.50 to 108.00 MHz
[Korea, Australia, U.K. and Europe models]
................................................................... 87.50 to 108.00 MHz
• Radio Frequency (Operational Frequency)
................................................................... 2402 MHz to 2480 MHz
Audio
• 50 dB quieting sensitivity (IHF-A, 1 kHz, 100% MOD.)
Mono ....................................................................3 V (20.8 dBf)
• Signal to noise ratio (IHF-A)
Mono/stereo ............................................................... 65 dB/64 dB
• Minimum RMS output power
(40 Hz to 20 kHz, 0.2% THD, 8)
[North America, General, Korea, Australia, U.K. and
Europe models].................................................. 100 W + 100 W
[Asia model] ............................................................. 85 W + 85 W
• Harmonic distortion (1 kHz)
Mono/stereo ..................................................................0.5%/0.6%
• Dynamic power per channel (IHF) (8/6/4/2Ω)
........................................................................125/150/165/180 W
• Tuning range
[North America model] .......................................530 to 1710 kHz
[General and Asia models] ...... 530 to 1710 kHz/531 to 1611 kHz
[Korea and Europe models] ................................531 to 1611 kHz
• Maximum power per channel (1 kHz, 0.7% THD, 4Ω)
[U.K. and Europe models] .................................................. 115 W
• Antenna input .......................................................... 75Ω unbalanced
ADDITIONAL
INFORMATION
• Input jack: NETWORK x 1 (100Base-TX/10Base-T)
AM (R-N303)
• IEC power (1 kHz, 0.2% THD, 8Ω)
[U.K. and Europe models] .................................................. 110 W
DAB (R-N303D)
• Damping factor (SPEAKERS A)
1 kHz, 8Ω.................................................................... 120 or more
• Support audio format
........................ MPEG 1 Layer II/MPEG 4 HE AAC v2 (AAC+ v2)
• Maximum effective output power
(1 kHz, 10% THD, 8Ω)
[General model] .................................................................. 140 W
[Asia model] ....................................................................... 125 W
• Antenna input ......................................................... 75Ω, unbalanced
• Tuning range ..............................................174-240 MHz (Band III)
• Input sensitivity/input impedance
CD, etc. ..................................................................500 mV/47 kΩ
53 En
English
Network
Specifications
General
• Power supply
[North America model] ......................................AC 120 V, 60 Hz
[General model] ...................... AC 110-120/220-240 V, 50/60 Hz
[Korea model] .................................................... AC 220 V, 60 Hz
[Australia model] .............................................. AC 240 V, 50 Hz
[U.K. and Europe models] ................................ AC 230 V, 50 Hz
[Asia model] ......................................... AC 220-240 V, 50/60 Hz
• Power consumption
[North America, General, Korea, Australia, U.K. and
Europe models] ................................................................200 W
[Asia model] ........................................................................165 W
• Standby power consumption ...................................................0.1 W
• Network Standby on
Wired.....................................................................................1.8 W
Wireless (Wi-Fi/Wireless Direct/Bluetooth) .........................1.9 W
• Dimensions (W  H  D) ................................435  141  340 mm
(17-1/8"  5-1/2"  13-3/8")
• Reference Dimensions (W  H  D) (with wireless antenna upright)
..........................................................................435  202  340 mm
(17-1/8"  8"  13-3/8")
* Including legs and protrusions
• Weight ..................................................................... 7.2 kg (15.9 lbs)
* The contents of this manual apply to the latest specifications as of
the publishing date. To obtain the latest manual, access the Yamaha
website then download the manual file.
54 En
Trademarks
Trademarks
Windows™
Windows is a registered trademark of Microsoft
Corporation in the United States and other countries.
Internet Explorer, Windows Media Audio and Windows
Media Player are either registered trademarks or
trademarks of Microsoft Corporation in the United States
and/or other countries.
Android™
Google Play™
Android and Google Play are trademarks of Google Inc.
The Wi-Fi CERTIFIED™ Logo is a certification mark of
Wi-Fi Alliance®.
The Wi-Fi Protected Setup™ Identifier Mark is a
certification mark of Wi-Fi Alliance®.
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in
some sections. You have the right to obtain, duplicate,
modify, and redistribute this open-source code only. For
information on GPL/LGPL open source software, how to
obtain it, and the GPL/LGPL license, refer to the Yamaha
Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
MusicCast is a trademark or registered trademark of
Yamaha Corporation.
Yamaha Eco-Label is a mark that certifies products of
high environmental performance.
(For R-N303D)
The unit supports DAB/DAB+ tuning.
Explanations regarding GPL
This product utilizes GPL/LGPL open-source software in
some sections. You have the right to obtain, duplicate,
modify, and redistribute this open-source code only. For
information on GPL/ LGPL open source software, how to
obtain it, and the GPL/LGPL license, refer to the Yamaha
Corporation website
(http://download.yamaha.com/sourcecodes/musiccast/).
ADDITIONAL
INFORMATION
DLNA™ and DLNA CERTIFIED™ are trademarks or
registered trademarks of Digital Living Network Alliance.
All rights reserved.
Unauthorized use is strictly prohibited.
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
English
Supports iOS 7 or later for setup using Wireless Accessory
Configuration.
“Made for iPod,” “Made for iPhone,” and “Made for
iPad” mean that an electronic accessory has been designed
to connect specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the developer to
meet Apple performance standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod,
iPhone, or iPad may affect wireless performance.
iTunes, AirPlay, iPad, iPhone, iPod, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
iPad Air and iPad mini are trademarks of Apple Inc.
App Store is a service mark of Apple Inc.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Yamaha Corporation is under license.
55 En
Index
A
ADVANCED SETUP menu.......................................... 43
AirPlay........................................................................... 35
AM antenna connection................................................. 12
AM tuning ..................................................................... 22
ANTENNA terminals...................................................... 7
Audio device connection ............................................... 10
Auto Preset, OPTION menu.......................................... 37
AutoPowerStby (Auto Power Standby),
SETUP menu ............................................................. 42
B
Balance, SETUP menu .................................................. 41
Basic playback operation............................................... 20
batteries............................................................................ 9
Bi-wire connection ........................................................ 11
Bluetooth ....................................................................... 30
Bluetooth, SETUP menu ............................................... 41
C
CD jacks .......................................................................... 7
CD player connection .................................................... 10
Clear Preset, OPTION menu ......................................... 37
Clock Time, Radio Data System ................................... 25
COAXIAL jack ............................................................... 7
Connectiion, Bluetooth device ...................................... 30
Connection, Network, SETUP menu............................. 40
D
DAB antenna connection............................................... 12
DAB tuning ................................................................... 26
DIMMER......................................................................... 8
DLNA ............................................................................ 32
DMC Control, Network, SETUP menu......................... 40
DVD player connection................................................. 10
F
Firmware update, ADVANCED SETUP menu ............ 44
Firmware update, SETUP menu.................................... 45
Firmware version........................................................... 43
FM antenna connection ................................................. 12
FM tuning ...................................................................... 22
Frequency, Radio Data System ..................................... 25
Front display, controls and functions .............................. 6
Front display, message .................................................. 51
Front panel, controls and functions ................................. 4
H
Headphones ..................................................................... 5
I
Information display, DAB radio station ........................ 28
Information display, Radio Data System....................... 25
Information switching ................................................... 20
Information, Network, SETUP menu............................ 40
INIT, ADVANCED SETUP menu................................ 43
Initialize......................................................................... 43
56 En
InitialVolume, SETUP menu........................................
Initiate Scan, OPTION menu........................................
Internet radio.................................................................
IP Address, Network, SETUP menu.............................
iPod content playback, AirPlay ....................................
iTunes content playback, AirPlay.................................
42
37
34
40
35
35
L
LINE jacks ...................................................................... 7
M
Manual network settings...............................................
Manual wireless network connection setting................
Max Volume, SETUP menu .........................................
Media sharing setup ......................................................
Message, front display ..................................................
MusicCast configuration...............................................
40
16
41
32
51
19
N
NAS connection............................................................ 13
NAS content playback .................................................. 32
Network Attached Storage connection ......................... 13
Network cable connection ............................................ 13
Network connection...................................................... 14
Network connection status............................................ 18
NETWORK jack............................................................. 7
Network Name, Network, SETUP menu...................... 41
Network, SETUP menu ................................................ 40
O
On/Off, Bluetooth, SETUP menu ................................. 41
OPTICAL jack................................................................ 7
OPTION menu.............................................................. 37
P
Pairing, Bluetooth device.............................................. 30
PC connection ............................................................... 13
PCs content playback.................................................... 32
PHONES jack ................................................................. 5
PHONO jacks ................................................................. 7
Playing back, Bluetooth device .................................... 30
Playing back, PCs/NAS content ................................... 32
Power cord connection.................................................. 13
Preset, DAB radio station ............................................. 27
Preset, FM/AM radio .................................................... 22
Program Service, Radio Data System........................... 25
Program Type, Radio Data System............................... 25
R
Radio Data System, FM radio ...................................... 25
Radio Text, Radio Data System.................................... 25
Rear panel, controls and functions.................................. 7
Remote control ID ........................................................ 43
Remote control, controls and functions .......................... 8
REMOTE ID, ADVANCED SETUP menu ................. 43
Repeat playback, AirPlay ............................................. 35
Repeat playback, PC music content.............................. 33
Index
S
SETUP menu ................................................................ 39
Shuffle playback, AirPlay............................................. 35
Shuffle playback, PC music content ............................. 33
Signal Info., OPTION menu ................................... 37, 38
Sleep timer .................................................................... 21
Speaker connection ....................................................... 11
SPEAKERS terminals .................................................... 7
Standby (Bluetooth Standby), Bluetooth,
SETUP menu ............................................................ 41
Standby (Network Standby), Network,
SETUP menu ............................................................ 41
T
TrafficProgram, OPTION menu ...................................
TU, ADVANCED SETUP menu .................................
Tune Aid, OPTION menu.............................................
Tuner frequency step ....................................................
Turntable connection ....................................................
37
43
37
43
10
U
Update (Network Update), Network, SETUP menu .... 41
UPDATE, ADVANCED SETUP menu ....................... 44
V
VERSION, ADVANCED SETUP menu ..................... 43
Vol.Interlock (Volume interlock), OPTION menu....... 38
Volume Trim, OPTION menu ...................................... 37
W
English
ADDITIONAL
INFORMATION
WAC ............................................................................. 14
Wireless Accessory Configuration ............................... 14
Wireless antenna ............................................................. 7
Wireless Direct ............................................................. 17
WPS push button configuration.................................... 16
57 En
Information for users on collection and
disposal of old equipment and used batteries:
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical
and electronic products and batteries should not be
mixed with general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to
applicable collection points, in accordance with your
national legislation.
By disposing of these products and batteries
correctly, you will help to save valuable resources
and prevent any potential negative effects on human
health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling
of old products and batteries, please contact your
local municipality, your waste disposal service or the
point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic
equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries
outside the European Union:
These symbols are only valid in the European Union.
If you wish to discard these items, please contact
your local authorities or dealer and ask for the
correct method of disposal.
Note for the battery symbol (bottom two
symbol examples):
This symbol might be used in combination with a
chemical symbol. In this case it complies with the
requirement set by the EU Battery Directive for the
chemical involved.
58 En
English
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Yamaha Music Europe GmbH declares that the radio
equipment type [R-N303, R-N303D] is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
https://europe.yamaha.com/en/support/compliance/doc.html
FR
BG
Bulgarian
ОПРОСТЕНА ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ
С а я
Yamaha Music Europe GmbH
а
а,
а
[R-N303, R-N303D] в
в
в
ва 2014/53/ С. Ця
я
а С
а а я а
а
в
в
а
а
а
я
а
:
https://europe.yamaha.com/en/support/compliance/doc.html
French
CS
Czech
DECLARATION UE DE CONFORMITE SIMPLIFIEE
Le soussigné, Yamaha Music Europe GmbH, déclare que
l'équipement radioélectrique du type [R-N303, R-N303D] est
conforme à la directive 2014/53/UE. Le texte complet de la
déclaration UE de conformité est disponible à l'adresse internet
suivante:
https://europe.yamaha.com/en/support/compliance/doc.html
ZJEDNODUŠENÉ EU PROHLÁŠENÍ O SHODĚ
Tímto Yamaha Music Europe GmbH prohlašuje, že typ rádiového
zařízení [R-N303, R-N303D] je v souladu se směrnicí 2014/53/
EU. Úplné znění EU prohlášení o shodě je k dispozici na této
internetové adrese:
https://europe.yamaha.com/en/support/compliance/doc.html
DE
DA
German
VEREINFACHTE EU-KONFORMITÄTSERKLÄRUNG
Hiermit erklärt Yamaha Music Europe GmbH, dass der
Funkanlagentyp [R-N303, R-N303D] der Richtlinie 2014/53/EU
entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter der
folgenden Internetadresse verfügbar:
https://europe.yamaha.com/en/support/compliance/doc.html
FORENKLET EU-OVERENSSTEMMELSESERKLÆRING
Hermed erklærer Yamaha Music Europe GmbH, at
radioudstyrstypen [R-N303, R-N303D] er i overensstemmelse
med direktiv 2014/53/EU. EU-overensstemmelseserklæringens
fulde tekst kan findes på følgende internetadresse:
https://europe.yamaha.com/en/support/compliance/doc.html
ET
SV
Swedish
FÖRENKLAD EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE
Härmed försäkrar Yamaha Music Europe GmbH att denna typ av
radioutrustning [R-N303, R-N303D] överensstämmer med
direktiv 2014/53/EU. Den fullständiga texten till EU-försäkran om
överensstämmelse finns på följande webbadress:
https://europe.yamaha.com/en/support/compliance/doc.html
Italian
Estonian
LIHTSUSTATUD ELI VASTAVUSDEKLARATSIOON
Käesolevaga deklareerib Yamaha Music Europe GmbH, et
käesolev raadioseadme tüüp [R-N303, R-N303D] vastab direktiivi
2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on
kättesaadav järgmisel internetiaadressil:
https://europe.yamaha.com/en/support/compliance/doc.html
EL
IT
Danish
Greek
DICHIARAZIONE DI CONFORMITÀ UE SEMPLIFICATA
Il fabbricante, Yamaha Music Europe GmbH, dichiara che il tipo
di apparecchiatura radio [R-N303, R-N303D] è conforme alla
direttiva 2014/53/UE. Il testo completo della dichiarazione di
conformità UE è disponibile al seguente indirizzo Internet:
https://europe.yamaha.com/en/support/compliance/doc.html
ΑΠΛΟΥΣΤΕΥΜΕΝΗ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ
Μ
πα
α / Yamaha Music Europe GmbH,
α
π
[R-N303, R-N303D] π
γ α 2014/
53/ΕΕ.
Τ π
ω
υ
φω
ΕΕ α
α
α
υ
α
α
υ :
https://europe.yamaha.com/en/support/compliance/doc.html
ES
HR
Spanish
DECLARACIÓN UE DE CONFORMIDAD SIMPLIFICADA
Por la presente, Yamaha Music Europe GmbH declara que el tipo
de equipo radioeléctrico [R-N303, R-N303D] es conforme con la
Directiva 2014/53/UE. El texto completo de la declaración UE de
conformidad está disponible en la dirección Internet siguiente:
https://europe.yamaha.com/en/support/compliance/doc.html
NL
Croatian
POJEDNOSTAVLJENA EU IZJAVA O SUKLADNOSTI
Yamaha Music Europe GmbH ovime izjavljuje da je radijska
oprema tipa [R-N303, R-N303D] u skladu s Direktivom 2014/53/
EU.
Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj
internetskoj adresi:
https://europe.yamaha.com/en/support/compliance/doc.html
Dutch
VEREENVOUDIGDE EU-CONFORMITEITSVERKLARING
Hierbij verklaar ik, Yamaha Music Europe GmbH, dat het type
radioapparatuur [R-N303, R-N303D] conform is met Richtlijn
2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan worden
geraadpleegd op het volgende internetadres:
https://europe.yamaha.com/en/support/compliance/doc.html
LV
Latvian
VIENKĀRŠOTA ES ATBILSTĪBAS DEKLARĀCIJA
Ar šo Yamaha Music Europe GmbH deklarē, ka radioiekārta
[R-N303, R-N303D] atbilst Direktīvai 2014/53/ES.
Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta
vietnē:
https://europe.yamaha.com/en/support/compliance/doc.html
59 En
English
EN
LT
Lithuanian
SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA
Aš, Yamaha Music Europe GmbH, patvirtinu, kad radijo įrenginių
tipas [R-N303, R-N303D] atitinka Direktyvą 2014/53/ES.
Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto
adresu:
https://europe.yamaha.com/en/support/compliance/doc.html
HU
Polish
UPROSZCZONA DEKLARACJA ZGODNOŚCI UE
Yamaha Music Europe GmbH niniejszym oświadcza, że typ
urządzenia radiowego [R-N303, R-N303D] jest zgodny z
dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest
dostępny pod następującym adresem internetowym:
https://europe.yamaha.com/en/support/compliance/doc.html
PT
Portuguese
DECLARAÇÃO UE DE CONFORMIDADE SIMPLIFICADA
O(a) abaixo assinado(a) Yamaha Music Europe GmbH declara
que o presente tipo de equipamento de rádio [R-N303, R-N303D]
está em conformidade com a Diretiva 2014/53/UE. O texto
integral da declaração de conformidade está disponível no
seguinte endereço de Internet:
https://europe.yamaha.com/en/support/compliance/doc.html
RO
Romanian
DECLARAȚIA UE DE CONFORMITATE SIMPLIFICATĂ
Prin prezenta, Yamaha Music Europe GmbH declară că tipul de
echipamente radio [R-N303, R-N303D] este în conformitate cu
Directiva 2014/53/UE. Textul integral al declarației UE de
conformitate este disponibil la următoarea adresă internet:
https://europe.yamaha.com/en/support/compliance/doc.html
SK
Slovak
ZJEDNODUŠENÉ EÚ VYHLÁSENIE O ZHODE
Yamaha Music Europe GmbH týmto vyhlasuje, že rádiové
zariadenie typu [R-N303, R-N303D] je v súlade so smernicou
2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto
internetovej adrese:
https://europe.yamaha.com/en/support/compliance/doc.html
SL
Slovenian
POENOSTAVLJENA IZJAVA EU O SKLADNOSTI
Yamaha Music Europe GmbH potrjuje, da je tip radijske opreme
[R-N303, R-N303D] skladen z Direktivo 2014/53/EU.
Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem
spletnem naslovu:
https://europe.yamaha.com/en/support/compliance/doc.html
60 En
Finnish
YKSINKERTAISTETTU EUVAATIMUSTENMUKAISUUSVAKUUTUS
Yamaha Music Europe GmbH vakuuttaa, että radiolaitetyyppi
[R-N303, R-N303D] on direktiivin 2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on
saatavilla seuraavassa internetosoitteessa:
https://europe.yamaha.com/en/support/compliance/doc.html
Hungarian
EGYSZERŰSÍTETT EU-MEGFELELŐSÉGI NYILATKOZAT
Yamaha Music Europe GmbH igazolja, hogy a [R-N303,
R-N303D] típusú rádióberendezés megfelel a 2014/53/EU
irányelvnek.
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a
következő internetes címen:
https://europe.yamaha.com/en/support/compliance/doc.html
PL
FI
TR
Turkey
BASİTLEŞTİRİLMİŞ AVRUPA BİRLİĞİ UYGUNLUK BİLDİRİMİ
İşbu belge ile, Yamaha Music Europe GmbH, radyo cihaz tipinin
[R-N303, R-N303D], Direktif 2014/53/AB'ye uygunluğunu beyan
eder. AB uyumu beyanının tam metni aşağıdaki internet
adresinden edinilebilir:
https://europe.yamaha.com/en/support/compliance/doc.html
Yamaha Global Site
https://www.yamaha.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Group
© 2017 Yamaha Corporation
Published 05/2017 AM-A0
10-1 Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650 Japan
AV16-0032
Download PDF
Similar pages