High Temp Dishwasher Instruction Manual

High Temp Dishwasher
Model CD-GR-1500
Item 45220
Instruction Manual
Revised - 02/24/2017
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: service@omcan.com
www.omcan.com
Table of Contents
Model CD-GR-1500
Section
Page
General Information --------------------------------------------------------------------------- 3 - 4
Safety and Warranty --------------------------------------------------------------------------- 4 - 5
Technical Specifications ---------------------------------------------------------------------- 5 - 6
Installation --------------------------------------------------------------------------------------- 6 - 7
Operation --------------------------------------------------------------------------------------- 7 - 10
Maintenance --------------------------------------------------------------------------------- 10 - 11
Troubleshooting ----------------------------------------------------------------------------- 12 - 13
Parts Breakdown ---------------------------------------------------------------------------- 14 - 24
Electrical Schematics ---------------------------------------------------------------------------- 25
Notes ------------------------------------------------------------------------------------------------- 26
Warranty Registration ---------------------------------------------------------------------------- 27
2
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modification to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
filled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’influence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modification
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton afin de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna influencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modificación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
Safety and Warranty
A door safety switch interrupts the appliance’s operation during washing, if the door is opened in error. The
pump motor winding has integrated thermal protection which interrupts power supply to the pump, in case
of overload or overheating. A thermal safety fuse interrupts power supply in case of booster or wash tank
overheating. No technical modifications are allowed in this appliance. The manufacturer is not responsible for
any resulting damages due to modifications. The same applies if the appliance is used for any other purpose,
except the ones indicated.
4
Safety and Warranty
Dishwasher Water is not potable.
Use, maintenance, and repair of dishwasher should be performed only by competent and informed persons
familiar with this machine.
1 YEAR PARTS AND LABOUR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classified as normal solid urban waste and can therefore be disposed of
without difficulty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specifications
Model
Basket Size
Wash Pump
CD-GR-1500
20” x 20” / 508 x 508mm
1.5 HP
Booster Tank: 7.4 L / 7.8 QT
Wash Tank: 68 L / 71.9 QT
Tank: 6kW / Booster Tank: 7.5 kW
8.2kW
208-240V/60hz
46A
0.5” / 13mm GPC (2LPC) 50°C/120.5°F
0.75” / 19mm House supplied
30-72 PSI
1.38” / 35mm House supplied
Capacity
Heating Element
Power
Electrical
Amps
Hot Water Requirements
Water Line Requirements
Water Pressure Requirements
Drain Line
5
Technical Specifications
Door Clearance
Dimensions (DWH)
Packaging Dimensions
Weight
Packaging Weight
Item Number
16” / 406mm
32.6” x 26” x 54.3” / 828 x 660 x 1379mm
30” x 35” x 57” / 762 x 889 x 1448mm
245 lbs. / 111.1 kgs.
266 lbs. / 120.7 kgs.
45220
Installation
The unit should be installed by licensed and approved personnel according to all local codes.
This dishwasher is delivered with water inlet and outlet hoses.
Be sure all electrical supply specifications correspond to information label on machine.
The manufacturer/ distributor is not responsible for any possible damages or risks due to improper connection
of this appliance.
INSTALLATION SUGGESTIONS
•
•
Place the dishwasher in the desired location.
The appliance should leveled. Adjustable feet are provided for this adjustment.
Note
The leveling feet should not have any exposed threads. Please use the provided bushes in
order to cover the exposed threads.
WATER SUPPLY CONNECTION
ATTENTION: Connection with the water supply should be made according to all applicable codes.
This dishwasher intended for use with a hot water supply but will also operate (at slightly reduced hourly
capacity) with a cold water supply.
• The water supply hose/pipe should be ½” or ¾” and terminate in a ¾” NPT fitting (not garden hose).
• The water supply hose/pipe should be flushed before final connection.
• Minimum flow pressure is 30 PSI (2 bars) and maximum is 75 PSI (5 bars).
• Connect hose supplied with machine to the inlet at the rear of the machine and the ¾” NPT fitting on the
water supply line.
Note to plumbing installer: If local codes require a vacuum breaker, one must be locally supplied and
6
Installation
installed in the supply line.
DRAINAGE CONNECTION
Outflow is accomplished by gravity (natural flow) in the CD-GR-1500. The outlet hose should be connected
either directly to a floor drain or drain which must not be higher than the level of the outlet at the rear of the
machine. An open drain connection or one to a vented drain pipe is recommended.
ELECTRICAL CONNECTION
The dishwasher operates under specific voltage as noted on the attached Technical Specifications label.
Note: A licensed electrician should be used for the connection according to local codes.
A 208 or 230 volt, one (1) phase, 60hz, 50A power circuit is required as unit draws 43A using 2 wire plus
ground. No neutral (115 volt service) is required. The ground line must be connected at the junction block.
Prepare power line with about 35” ( 95 CM ) of wire with the shielding removed. Install either a ¾” connector or
½” with ½” x ¾” bushings.
Open front control panel by removing two nuts and open inside cover by removing 4 nuts holding cover.
Insert power line in appropriate ¾” hole in rear panel, or if suitable, a ½” connector with bushings can be used,
mount connector, and feed wire to front control box terminals. Mounting posts are provided to hold wires with
“Tye Wraps”. Allow sufficient slack at panel end to allow wire to move when control panel is repositioned to
closed.
Connect power line to junction block. Be sure connections are tight.
Close control panel cover with the 4 nuts, and close the front panel with the two acorn nuts.
After installation, the dishwasher should be cleaned thoroughly before putting into operation.
Operation
INSTRUCTIONS FOR REGULAR OPERATION
The appliance is intended to clean dishes, cups, glasses, silver, etc. Be sure the items placed to be washed
are suitable for dishwashing. Silver should be cleaned of heavy food residues, if not washed right after use.
This machine is not intended for use with items which were used with acids, mineral oil, grease, gasoline or
colors.
7
Operation
PREPARATION OF DISHES FOR WASHING.
For best results avoid allowing food residues to dry. Remove bulk food residues, olive pips, lemon peels, tooth
picks, etc., before placing the dishes in the basket.
If washing is delayed, we recommend that you soak dishes and/or glasses which have food residues.
LOADING BASKETS
Place glasses and cups, with the opening facing down and not piled one on top of the other, in
the appropriate baskets. Glasses should not touch each other (damage to glass or stains due
to contact may occur).
Plates should be stacked vertically in appropriate baskets and not touching each other, look
to the side of the baskets to see the recommended loading capacity.
Place tableware in the supplied plastic basket, with handles downwards or placed freely in
a level plastic basket.
In any case, avoid overloading.
AUTOMATIC FILLING OF DETERGENT
This model has an automatic detergent pump for use with a container of non foaming liquid detergent. The
detergent pump is a peristaltic regulated (looks exactly like the rinse-aid pump) and can be regulated by a
screw above and on the right of the glass cover. The regulation can be from 0 lt/hour to 3,0 lt/hr.
both pumps are mounting vertically on an inox bracket in front of the washing pump and are marked with two
yellow stickers.
MANUAL FILLING OF DETERGENT
Use only non-foaming detergent suitable for commercial dishwashers. In the event of non use or malfunction
of the automatic detergent injection system, put the detergent suppliers recommended amount directly into the
wash compartment tank after the machine has reached its operating temperature.
The correct dosage depends on the water hardness and the amount of dirt on the dishes.
Follow the detergent manufacturer’s recommendations. Less detergent deters good washing results and more
detergent usually does not provide better results, but rather more unnecessary consumption and environment
pollution.
Do not use granular detergent. Poor results usually occur.
Do not use caustic products. This will void the guarantee.
8
Operation
RINSE-AID PUMP
Before you perform these adjustments, turn off the power supply.
This model has an automatic rinse-aid pump for use with a container of liquid rinse-aid. The rinse-aid pump is
a peristaltic regulated (looks exactly like the detergent pump) and can be regulated by a screw above and on
the right of the glass cover. The regulation can be from 0 lt/hour to 0,7 lt/hr.
The dozer is adjusted from the manufacturer’s premises at its maximum value for easy initial priming
and must be adjusted accordingly (depending on water hardness, water pressure, how dirty the dishes
are, and the detergent used).
For initial priming of dozer, during the initial filling of the wash tank, start by switching on machine normally.
While the wash tank is filling, during the initialization only, open and close the door in 5 second intervals. Be
careful of spraying water. Do this for about 10 times, and the rinse system will be primed. Empty wash tank and
fill normally. Operate 2 or 3 wash cycles and machine is now ready to be calibrated or ready for normal use.
To reduce (-) the amount of rinse aid, turn the center screw clockwise. To increase (+), turn counterclockwise.
Note: this is a 15 revolution adjusting screw to provide fine adjustments as required.
Hint to installing personnel: After priming system by operating machine through several cycles, rotate
adjusting screw gently to full closed position (clockwise) and adjust (counter-clockwise) about 7 full revolutions.
Empty wash tank and refill with fresh water. Operate for two or three cycles and verify concentration level.
Adjust dozer to achieve final desired results.
OPERATION
1.
2.
3.
4.
5.
6.
Check that the pump inlet filter has been placed in the correct position if it was removed for cleaning.
Check that the overflow stand pipe is inserted correctly in its outlet.
Close door.
Turn power switch to “ON” (switches should now illuminate.)
The dishwasher will fill automatically.
The booster indicator should come on to indicate that the inlet water to the rinse and fill system is being
heated to the required rinse temperature (usually 195°F / 91°C.)
7. When the booster water has reached the correct temperature, the corresponding light switches off and the
wash tank light comes on if the wash water temperature is not sufficiently hot (usually 165°F / 74°C.)
8. At initial daily start, allow about 10 to 20 minutes for machine to stabilize water temperatures to their proper
temperatures.
Note: After warm-up, one initial wash cycle should be performed to thoroughly mix soap and water
and be sure unit is fully warmed up and ready to wash properly.
9. After initial warm-up, when all heater lights are off, the dishwasher is ready to wash.
Note: If door is opened during operation, the safety control will turn off the timer. Washing or
rinsing will restart from beginning of wash cycle.
10.Open the door, insert the basket with the items (dishes, glasses, etc.) noting that heavy food residue
has been removed. (If the automatic soap injection system is not used, pour the proper amount of liquid
9
Operation
detergent manually into the wash tank.) Close the door.
11.To start the washing program, select the program desired and close the door. The automatic program
commences, with the green program indicator light in the program selector switch changing from flashing to
steady.
Note: This unit is equipped with a “positive rinse temperature control and will not advance from
wash to rinse unless the rinse water is at the preset temperature (usually about 195°F / 91°C.)
12.When the program is finished, the green program light returns to flashing.
13.Promptly open the door and remove the basket with the clean items. Use caution with hot items.
14.Allow to dry.
If, after washing, there are stains from dirt or water spots, the cause may be one of the following:
• Wrong ratio of detergent to water.
• Rinsing water with very high mineral content.
• Improper quantity of rinse-aid.
• Wrong arrangement of items in the basket.
• Low water pressure during rinsing.
• Low water temperature during washing.
• Clogged or miss-positioned filters.
• Clogged jets.
Note
• The wash temperature must be within ≥ 74°C & ≤ 84°C and the rinse temperature must be within ≥ 74°C &
≤ 91°C.
• Please check during the operation that the rinse water pressure is within its limits (20 ± 5 psi).
Maintenance
DAILY MAINTENANCE OPERATION.
• Turn the power switch off.
• Empty the wash tank by removing the overflow standpipe.
• Remove and clean the pump inlet filter and the four sediment filters.
• Rinse the washing compartment to remove any dirt residues.
• Reassemble the parts in reverse order.
The appliance should never operate without the pump filter in place.
HOW TO DRAIN THE MACHINE
1.
2.
3.
4.
Turn the power switch to drainage.
Remove the surface filters.
Remove the overflow pipe from the tank.
Leave the machine to drain by gravity.
10
Maintenance
MAINTENANCE / CARE / REPAIR
Proper operation and safe use may be ensured only through the correct use of the appliance, as well as
the compliance with the operation instructions, the corresponding specifications and the care and cleaning
indications.
Notice: Before cleaning or performing any maintenance, other than daily interior cleaning, power and water
supply must be turned off. The appliance should never be sprayed with water or high pressure cleaning
solution, because any water or solution which may get into the electrical components will affect operation of the
appliance as well as present a potential for electrical shock. No safety systems should be disabled.
REGULAR MAINTENANCE AND CLEANING WORKS
Depending on local water hardness, the nozzles on the rinse arms should be cleaned regularly. Caution must
be exercised to not damage the nozzles.
PAY ATTENTION TO THE CORRECT POSITION OF FILTERS AND WASH ARM INSTALLATIONS AND BE
SURE NON-STICK BUSHINGS ARE NOT WORN.
Clean the appliance with warm water and conventional cleaning aids.
Stainless steel parts should never be cleaned them with “steel wool”, wire brush, etc, since even the lightest
contacts on the surfaces with steel may contaminate the stainless steel and cause rust formation. Use brushes
made of polymer plastic, natural bristles, or thin brass wire. Always keep brush movements in line with grain in
the Stainless Steel so that you will not affect the appearance. Finally, rinse with clean water and dry thoroughly.
We remind you that corrosion (rust formation) on stainless steel surfaces is not created by itself, but
rather due to the use of improper cleaning products (e.g. whitening or particularly caustic cleaning
products based on chlorine). Occasionally calcium sediments will form on the internal walls of the
dishwasher (due to mineral particles in the water), which may affect the correct operation of the
appliance and requiring regular removal.
SPARE PARTS, ACCESSORIES AND COMPONENTS
Spare parts and components are usually available at the authorized local service agency, or directly from
Omcan, In case of claims or complaints, you must supply the model and serial number of the appliance /
machine found on the specification label of the appliance.
11
Troubleshooting
PROBLEM
The dishwasher does not operate.
CAUSE
No power to the machine.
Control switch S1 not activated.
Switch S1 is faulty.
Water supply not turned on.
Door is not closed.
Water inlet valve is faulty.
Fill water runs continuously.
Overflow drain stand pipe not
installed properly.
The appliance operates, but the
The pilot light is faulty.
green operating pilot light does not Wire lead to lamp disconnected.
illuminate.
Lamp is out of it’s socket.
Booster not heating.
Switch S1 or main switch or fuse
has not been activated.
Booster heating operates, but pilot
light does not turn on.
Wash tank heating does not
operate.
The booster thermostat is faulty.
The booster 105°C thermal fuse is
faulty.
Pressure switch is faulty.
Booster heating contactor is faulty.
The pilot light is faulty.
Wire lead to lamp disconnected.
Lamp is out of it’s socket.
The wash tank thermostat is faulty.
The 90°C thermal fuse is burned or
defective.
12
SOLUTION
Check the connection.
Breaker or fuse has not been
activated or is faulty.
Turn switch S1 on.
Refer to the authorized service
agency, local dealer, or Omcan.
Turn the supply on.
Close the door.
Refer to the authorized service
agency, local dealer, or Omcan.
Install overflow drain stand pipe.
Verify that overflow drain stand
pipe is installed properly with
overflow slots upwards.
Change the pilot light.
Reconnect power lead.
Insert lamp.
Check the switch S1 of the
appliance and the main switch or
fuse.
Refer to the authorized service
agency, local dealer, or Omcan.
Change the pilot light.
Reconnect power lead.
Refer to the authorized service
agency, local dealer, or Omcan.
Troubleshooting
Pump motor does not operate.
Main switch or fuse is not
activated.
The door is not closed.
Main relay is faulty.
Pump motor is faulty.
Program timer is faulty.
Motor operates, but pump does not An object has jammed the pump
rotate.
impeller.
Hard water deposits or detergent
have been petrified following non
operation of the appliance.
Washed items do not dry (dishes,
Rinse aid supply is empty.
glasses, etc.)
Rinse aid “dozer” valve is
defective.
Timer is faulty.
Rinse arms (upper and/or lower)
do not rotate.
Activate main switch or fuse.
Close the door.
Refer to the authorized service
agency, local dealer, or Omcan.
Loosen deposits by rotating screw
on rear side of pump motor.
Replace or refill rinse aid container.
Refer to the detergent supplier,
authorized service agency, local
dealer, or Omcan.
Refer to the authorized service
agency, local dealer, or Omcan.
Clean nozzles.
Replace Teflon bushings if worn.
Note: take caution to not install
rinse arm without bushings.
REFERENCE
Item Number Model Number
45220
CD-GR-1500
Description
Dishwasher Heavy Duty 20” x 20” /
508mm x 508mm 208-240V/60/1
13
Manufacturer Model Number
C1500
Parts Breakdown
Model CD-GR-1500 45220
14
Parts Breakdown
Model CD-GR-1500 45220
15
Parts Breakdown
Model CD-GR-1500 45220
16
Parts Breakdown
Model CD-GR-1500 45220
17
Parts Breakdown
Model CD-GR-1500 45220
18
Parts Breakdown
Model CD-GR-1500 45220
19
Parts Breakdown
Model CD-GR-1500 45220
20
Parts Breakdown
Model CD-GR-1500 45220
21
Parts Breakdown
Model CD-GR-1500 45220
22
Parts Breakdown
Model CD-GR-1500 45220
Item No.
Description
61020
Front Cover Screw INOX M6x25 for
C1500
61021
Control Panel with Switches for C1500
Position
Item No.
Description
Position
Item No.
Description
Position
1
60311
Rinse Aid Inlet Tube 4x6mm (Blue) for
C1500
32
73821
INOX Nut M3 for C1500
64
2
61006
Balance F15x20 for C1500
33
60973
Pipe Rubber Protector for C1500
65
34
61031
Power Supply Board 6 Con. for C1500
66
73831
Lock Washer INOX 4 for C1500
3
61007
Filter Plastic for Rinse Aid Valve for
C1500
60952
INOX Nut M4 for C1500
4
61024
Leveling Feet 1 3/4in 304 145/210
M10x25 for C1500
35
73834
M4 Nut Galvanised for C1500
67
73752
Back Cover 1500 for C1500
5
73773
Detergent Tank Injector for C1500
36
73831
Lock Washer INOX 4 for C1500
68
73832
Lower Back Cover 1500 for C1500
6
41090
Pressostat Switch for C1500
37
41119
Relay Magnetic Contactor for C1500
69
73829
INOX Tapping Screw 4.2x13 for C1500
7
60959
Tapping Screw 3.5x9.5 for C1500
38
61032
Timer Electronic for C1500
70
73868
Tapping Screw 4.2x19 for C1500
8
73843
Nut M6 Galvanised for C1500
39
61033
Pipe Rubber Protector for C1500
71
40
73854
Pump Inlet Hose for C1500
72
61022
Teflon 10-4-1 for C1500
8-1
73800
Galvanised Lock Washer 6.4x11x0.7
for C1500
60952
INOX Nut M4 for C1500
9
61025
Electrical Box Complete for C1500
41
73768
Clamp 60-80 for C1500
73
73808
INOX Axle Bolt Short M8x17 for C1500
10
61026
Front Cover 1500 for C1500
42
73766
Clamp 40-60 for C1500
74
73807
INOX Axle Bolt M8x35 Long for C1500
11
61027
Film for Omcan for C1500
43
73855
Pump Output Hose for C1500
75
73772
Copler 8x31 for C1500
12
41134
On/Off Switch 0-1 Green LED for C1500
44
73843
Nut M6 Galvanised for C1500
76
45
73800
Galvanised Lock Washer 6.4x11x0.7
for C1500
77
46
73884
Washer Steel 6x18 for C1500
78
79
73872
Teflon Washer 16x8x1mm for C1500
13
41104
Cycle Selection Switch 0-1-2 LED for
C1500
73883
Washer INOX 6x18 for C1500
14
41120
Light Indicator Orange for C1500
73822
INOX Nut M8 for C1500
15
61028
Lock Washer 4 Dia. for C1500
47
73852
Pump 1.5 HP 208-240V 6 2P UL for
C1500
73776
Door Handle 1500 for C1500
16
73834
M4 Nut Galvanised for C1500
48
73772
Copler 8x31 for C1500
80
49
61034
Boiler 1500 400V Complete (1 Heating
Elements) for C1500
81
73833
M10 Nut INOX for C1500
17
73761
Bracket for Two Peristaltic Pumps for
C1500
73811
INOX Bolt M10x64 Allen for C1500
18
60985
Peristaltic Detergent Pump G300/230V
for C1500
50
41087
Tank Thermofuse 90°C for C1500
82
73847
Plastic Guide D.30 for C1500
19
60984
Peristaltic Rinse Aid Pump G302/230V
for C1500
51
73821
INOX Nut M3 for C1500
83
73869
Tapping Screw 4.8x13 for C1500
20
60979
Thermometer for Tank 2in 20/220F for
C1500
52
60972
Fitting 1/4x7 Male for C1500
84
61023
Upper Cover for C1500
21
60980
Thermometer for Booster 2in 20/220F
for C1500
53
60970
Inlet Valve Extension to Pressure Gauge
for C1500
85
73812
INOX Bolt M8x70 for C1500
22
60981
Pressure Gauge 2in 0/60 PSI 1/4 NPT
for C1500
54
60969
Galvanised Bolt M4x10 for C1500
86
73817
INOX Hood Spacer 12x24 for C1500
23
60982
Bracket for Pressure Gauge Thermometer for C1500
55
60971
Gasket for Inlet Hose for C1500
87
73872
Teflon Washer 16x8x1mm for C1500
24
73817
INOX Hood Spacer 12x24 for C1500
56
41112
Water Input Solenoid Valve for C1500
88
89
73883
Washer INOX 6x18 for C1500
25
73884
Washer Steel 6x18 for C1500
57
73840
Non Return Valve for Rinse Aid Pump
for C1500
73822
INOX Nut M8 for C1500
26
61029
Electrical Components Panel for C1500
58
73870
Tee-Connection Boiler with 1/8 for C1500
90
73805
Hood Support Pipe 30x1100 for C1500
27
61030
Electrical Components Panel for C1500
59
61019
Clamp 10-16 for C1500
91
41122
Door Spring Turbo for C1500
28
41118
Thermostat 0-90°C 1500mm for C1500
60
61035
Washing Machine Hose Black 10x16.5
for C1500
92
73839
Non Return Valve (DVGW) for C1500
29
73876
Thermal Overload Relay 7.0-10.0 for
C1500
61
61036
Boiler Turbo for C1500
93
60310
Detergent Inlet Tube 4x6mm
(Transparent) for C1500
30
73801
Galvanised Machine Screw M4x5 for
C1500
62
61037
Heater Element Boiler 1500, 7.5kW
for C1500
94
60968
Cable Rubber Protector for C1500
31
73838
Micro Relay 8 Pins Faston for C1500
63
73758
Boiler Element Fitting Base for C1500
95
23
Parts Breakdown
Model CD-GR-1500 45220
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
126
73871
Teflon 12-6-2 for C1500
156
41088
Boiler Thermofuse 105°C for C1500
96
73806
INOX Axle 20/8 Turbo 1500 Evo for
C1500
73821
INOX Nut M3 for C1500
97
73795
Flow Control Disc for Base for C1500
127
61048
Tank Filter Base Rubber Gasket Turbo
for C1500
157
73757
Boiler Drain Threaded Cap for C1500
98
41136
INOX Angle Male/Female 1/2'' for C1500
128
61049
Retaining Plate for Filter for C1500
158
73884
Washer Steel 6x18 for C1500
99
73816
INOX Hex Bolt M6x20 for C1500
129
73884
Washer Steel 6x18 for C1500
159
73800
Galvanised Lock Washer 6.4x11x0.7
for C1500
100
73871
Teflon 12-6-2 for C1500
130
73800
Galvanised Lock Washer 6.4x11x0.7
for C1500
160
73843
Nut M6 Galvanised for C1500
101
73861
Rubber Gasket 109x54x3 for C1500
131
73843
Nut M6 Galvanised for C1500
161
73802
Heater Element Cover for C1500
102
61040
Retaining Plate Turbo for C1500
132
73794
Filter Retaining Nut for C1500
162
133
41128
Tank Heating Element 6Kw for C1500
163
60978
O-Ring 45x6 for C1500
103
73800
Galvanised Lock Washer 6.4x11x0.7
for C1500
73834
M4 Nut Galvanised for C1500
104
73843
Nut M6 Galvanised for C1500
134
73867
Tank Heating Element Retaining Bracket
for C1500
164
73856
Rinse Base TUR - KN for C1500
105
73884
Washer Steel 6x18 for C1500
135
73802
Heater Element Cover for C1500
165
136
73834
M4 Nut Galvanised for C1500
166
73815
INOX Hex Bolt M4x60 for C1500
106
41123
Rinsing and Washing Arms Cross Plastic
for C1500
73868
Tapping Screw 4.2x19 for C1500
107
73845
Pipes Turbo 1500 INOX 30x1x248 for
C1500
137
73803
Heating Element Nut 13mm M4-M6
for C1500
167
41140
O-Ring 10.5x3 for C1500
108
73826
INOX Screw 4.2x13 for C1500
138
73878
Threaded Shaft M4x60 for C1500
168
73831
Lock Washer INOX 4 for C1500
109
41127
Teflon 18x10 for C1500
139
61050
O-Ring 45x6 for C1500
169
73882
Wash Supply INOX Turbo for C1500
110
41085
Sprayer for Rinsing Arm for C1500
140
41131
Drain and Overflow Pipe for C1500
170
60952
INOX Nut M4 for C1500
111
73825
INOX Screw 2.9x10 for C1500
141
61000
Rubber Gasket 35x55x1 for C1500
171
172
41139
Rinse Pipe Retaining Nut for C1500
112
61041
Plastic Cap for Rinse Arm for C1500
142
73780
Drain and Overflow Base Nut 1 1/2 for
C1500
73858
Rinse Supply Inox Turbo for C1500
113
61042
Rinse Arm Turbo for C1500
143
41132
Drain and Overflow Base for C1500
173
73774
Domed Cap Nut M6 for C1500
114
73868
Tapping Screw 4.2x19 for C1500
144
41140
O-Ring 10.5x3 for C1500
174
41137
INOX Niple 1/2'' for C1500
115
73819
INOX Machine Screw 3.5x13 for C1500
145
73833
M10 Nut INOX for C1500
175
73841
Nut 1/2 for C1500
116
61043
Rinse Arm Turbo for C1500
146
41091
Pressostat Chamber for C1500
176
177
73749
O-Ring 20x4 for C1500
117
73793
Filter Element for C1500
147
61051
Washing Machine Hose Black 10x16.5
for C1500
41125
Wash and Rinse Base Upper Plastic
for C1500
118
61044
INOX Knob for Square Tank Filter 1500600 for C1500
148
61052
Washing Machine Hose Black 10x16.5
for C1500
178
41136
INOX Angle Male/Female 1/2'' for C1500
119
61045
INOX Hex Screw M6x12 for C1500
149
61053
Washing Machine Hose Black 10x16.5
for C1500
179
73806
INOX Axle 20/8 Turbo 1500 Evo for
C1500
120
61046
Basket Support for C1500
150
61054
Tubo Cristallo 4x6 for C1500
180
61038
Wash and Rinse Cross Turbo Complete
for C1500
121
73863
Support for Filter Back for C1500
151
61055
Tubo Cristallo 4x6 for C1500
181
41124
Wash and Rinse Group Retaining Nut
25-7-8 for C1500
122
61047
Domed Cap Nut M6 for C1500
152
61056
Tubo PVC Blue 4x6 for C1500
182
41126
Wash and Rinse Base Lower Plastic
for C1500
123
73864
Support for Filter Mid for C1500
153
61057
Washing Machine Hose Black 6x12
for C1500
183
41124
Washe and Rinse Group Retaining Nut
25-7-8 for C1500
124
73853
Pump Filter Turbo for C1500
154
61038
Wash and Rinse Cross Turbo Complete
for C1500
125
73816
INOX Hex Bolt M6x20 for C1500
155
24
Electrical Schematics
Model CD-GR-1500 45220
H
Magnetic
Contactor
Booster’s Heating
Element
Tank’s Heating
Element
Indicator Lamp
Y
Water Inlet Valve
MS
Main Switch
TM
Electronic Timer
SS
Program Selector
Switch
M1
Wash Pump Motor R1
DS
Door Switch
M2
PS
Pressure Switch
K4
TF
Thermofuse
K1
TH
Thermostat
K2
Detergent Pump
Motor
Microrelay
Magnetic
Contactor
Magnetic
Contactor
K3
R2
K1.A Aux Contact
25
OR
Overload Relay
C
Capacitor
ORC
Overload’s Relay
Breaking Contact
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
26
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specified below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécifié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
www.omcan.com/warrantyregistration.html
For mailing in Canada
For mailing in the US
Pour postale au Canada
Pour diffusion aux États-Unis
Por correo en Canadá
Por correo en los EE.UU.
OMCAN
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
Canada, L5L 4X5
USA, 14305
or email to: service@omcan.com

Purchaser’s Information
Name:
Company Name:
Address:
Telephone:
City:
Province or State:
Postal or Zip:
Country:
Email Address:
Type of Company:
Dealer from which Purchased:
Dealer City:
Dealer Province or State:
Restaurant
Bakery
Deli
Butcher
Supermarket
Caterer
Institution (specify):
Invoice:
Other (specify):
Model Name:
Model Number:
Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY):
Would you like to extend the warranty?
Date of Installation (MM/DD/YYYY):
Yes
No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
27
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualified local sales
and service representatives who provide convenient access to over 3,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualifiées et des représentants de service qui offrent un accès facile à plus de 3500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 3,500 productos con origen a nivel mundial.
Download PDF
Similar pages