WALL FAN HEATER
UWH1002W
TÈME QUAL
ITÉ
SYS
This unit complies
with CSA and UL
standards
EG
IÉ - R ISTERE
D
TIF
Q
ER
STEM
Y SY
LIT
UA
C
USER’S GUIDE
REPLACEMENT COMPONENT LIST INCLUDED
UNIWATT is a line of products manufactured by STELPRO. For more information please contact customer service.
INSUWH0315
SAVE THESE INSTRUCTIONS
WARNING
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and
keep them handy for future reference. If these instructions are not followed, the warranty will be considered null and void and the
manufacturer deems no further responsibility for this product.
This product must be installed by a qualified person and connected by a certified electrician, according to the electrical and
building codes effective in your region.
The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially
fatal electric shocks.
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
This unit has only one installation position. The top of the unit must face up.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative). Use this heater only as described in this
manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. Do not use outdoors.
RECOMMENDED HEATING CAPACITY: 1.25 W/cubic foot (0.03 m³)
It corresponds to 10 W/square foot (0.09 m²) based on a standard ceiling height of 8 feet (2.44 m). The recommended capacity is usually sufficient
for normal heating needs. Please note that the insulation quality of walls and windows are some of the factors that influence heat losses, which modify the
required capacity to heat a room. If needed, refer to a specialist who will be able to calculate these heat losses and optimize the required capacity or consult
the “Online heating calculation” section of the Stelpro website (residential buildings). To heat a large room and to increase your comfort, it is recommended
to install several units instead of one. For example, 2 X 1000 W rather than 1 X 2000 W.
Do not install the unit where objects or pieces of furniture could be heat damaged.
If the unit’s capacity is insufficient for the size of the room, it will be in operation continuously, and may become defective earlier and turn yellow.
Respect distances and positions indicated in the installation section.
If the installer or user modifies the unit, they will be held responsible for any damage resulting from this modification, and the CSA certification could be void.
This unit must not come into contact with a water source and must be protected from splashes (e.g. a wet mop). Do not use it if any part has been immersed.
Moreover, do not turn it on or off when standing in water or if your hands are wet.
When mounting the unit, make sure that the anchorage used can support the total weight of the unit with the mounting brackets.
When cutting or drilling into a wall, do not damage electrical wiring and other hidden utilities.
When starting up the unit for the first time or after a long period, it is normal that it produces some temporary odours and whitish smoke.
Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be careful and responsible when using it. To avoid burns, do not
let bare skin touch hot surfaces. Let the unit cool down for a few minutes before handling it (it stays warm for some time after shut-down). Extreme caution is
necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
This unit must be installed at least 8 in (20.3 cm) from any adjacent surfaces (walls and floors). Moreover, make sure objects or pieces of furniture such as, but not
limited to, blankets, towels, beds, laundry baskets, clothing, papers, electric wires and other flammable items, do not come into contact with the unit and keep them
at least 3 feet (91 cm) from the unit. Failure to comply with this warning could lead to a fire. Some materials are more heat-sensitive than others, so make sure
those near the unit can withstand heat.
Do not install on a wall behind a door.
Never block air vents (with objects or other items). You risk damaging the heater and the obstruction could lead to electric shock or overheating, which
could result in a fire.
Do not insert or allow foreign objects to enter any air vent as this may cause electric shocks, a fire or damages to the unit.
This unit has hot and arcing or sparking parts inside. It is not designed to be used or stored in wet areas or areas containing flammable liquids, combustible
materials or corrosive, abrasive, chemical, explosive and flammable substances such as, but not limited to, gasoline, paint, chlorine, sawdust and cleaning
products.
Some areas are dustier than others. Thus, it is the user’s responsibility to evaluate if the unit must be cleaned based on the amount of dirt accumulated on
and inside air vents. Accumulated dirt can lead to a component malfunction or give a yellowish colour to unit. Failure to install and maintain unit in accordance
with these instructions poses a fire hasard.
Thermal protection activation indicates that the unit has been subjected to abnormal operating conditions. If the thermal protection remains activated or
activates and deactivates repeatedly, it is recommended that a qualified electrician or a certified repair centre examine the unit in order to make sure it is not
damaged. (Refer to the limited warranty.)
Before unplugging the unit, all controls must be in the “OFF” position and the current from the main breaker panel should be cut. (The general switch may be
used also, if included.)
If the unit is damaged or defective, discontinue use, cut off power supply at circuit breaker and contact a certified electrician or certified repair centre. (Refer
to the limited warranty)
SAVE THESE INSTRUCTIONS
Note: When a part of the product specification must be changed to improve operability or other functions, priority is given to the product specification itself. In such
instances, the instruction manual may not entirely match all the functions of the actual product. Therefore, the actual product and packaging, as well as the name
and illustration, may differ from the manual.
2
INSUWH0315
TECHNICAL DRAWINGS AND SPECIFICATIONS
TECHNICAL DRAWINGS
109mm
4 9/32"
267mm
10 1/2"
203 mm
8''
90mm
3 17/32"
74mm
2 59/64"
50mm
1 61/64"
27mm
1 3/64"
225mm
8 7/8"
26mm
1 3/64"
22mm
7/8"
KOE
373mm
14 11/16"
27mm
1 3/64"
19mm
3/4"
25mm
1"
324mm
12 25/32"
KOE
22mm
7/8"
l
m
203 mm
8''
DESSUS
TOP
DEVANT
FRONT
CÔTÉ
SIDE
SPECIFICATIONS
WALL FAN HEATER
VOLTS
240 V
WATTS
1000 W
AMPS
4.16
WEIGHT
FREQUENCY
6.7 lb / 3.04 kg
60 Hz
DEPTH
4 9/32” / 109 mm
WIDTH
10 1/2” / 267 mm
HEIGHT
14 11/16” / 373 mm
3
INSUWH0315
INSTALLATION
INSTALLATION
N.B. CUT OFF POWER SUPPLY AT CIRCUIT BREAKER/FUSE BEFORE PROCEEDING WITH INSTALLATION.
INSTALLATION POSITION MUST BE RESPECTED : INSTALL WITH TOP OF UNIT FACING UP ONLY. TO
REDUCE THE RISK OF FIRE, DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THE HEATER.
DO NOT MOUNT IN CONTACT WITH COMBUSTIBLE MATERIAL. DO NOT MOUNT IN CLOSE PROXIMITY TO
ANOTHER UNIT.
Keep the front and and upper sides of the unit at least 8 inches (20.3 cm) from any adjacent surfaces. Moreover, make sure objects or pieces of
furniture such as, but not limited to, blankets, towels, beds, laundry baskets, clothing, papers, electric wires and other flammable items, do not come into
contact with the unit and keep them at least 3 feet (91 cm) from the unit. Failure to comply with this warning could lead to a fire. Some materials are
more heat-sensitive than others, so make sure those near the unit can withstand heat.
ELECTRICAL CONNECTIONS
WITHOUT THERMOSTAT
C-633
L1
FU
HEATING
ELEMENTS
éléments
chauffant
MT
PROT1
E1
C-189
L1
A
MT
M1
L2
M
C-605
L2
WITH BUILT-IN THERMOSTAT
TH1
L1
C-633
FU
éléments
chauffant
HEATING
ELEMENTS
MT
L1
TH2
M1
M
A
MT
L2
C-605
L2
TH1
L1
PROT1
E1
C-189
C-633
FU
HEATING
ELEMENTS
éléments
chauffant
MT
L1
L2
PROT1
E1
C-189
M1
M
A
MT
L2
C-605
LEGEND
WIRE
GAGE 14 TEW
M1
240 V MOTOR
E1 & E2
RESISTANCE WIRES
PROT 1
100° C THERMAL PROTECTION
MT
T&B 833 CONNECTOR
HEATING ELEMENT
RESISTANCE WIRES AND THERMAL PROTECTION KIT
FU
104° C FUSELINK
4
INSUWH0315
INSTALLATION, MAINTENANCE AND OPERATION
WALL INSTALLATION POSITION
RECESSED INSTALLATION
This unit must be installed at a minimum
distance of 8” (20 cm) from adjacent walls
and the floor.
236
9 5/16"
Front grill
203 mm
8''
minimum
19mm
3/4"
Recessed box
88mm
3 31/64"
327
12 7/8"
203 mm
8''
minimum
When the unit is recessed,
the edge of the back box
must be installed flush with
the finished wall.
INSTALLATION OF THE BACK BOX IN A NEW BUILDING
WARNING : This unit must be installed at least 8” (20 cm) from adjacent walls and the floor.
1.Determine which side of the back box is to be mounted against a stud or ceiling joist. Allow for the thickness of the finished wall when installing
the back box. The edge (shoulder) of the back box must be installed flush with the finished wall.
2.Cut hole in wall (see image).
3.Position the back box on the appropriate stud or joist location and secure it using two nails or screws.
4.Remove one knockout in the back box to allow for the entry of the power supply cable (see image).
5.Bring the power supply cable to the back box. Install a cable clamp and route the cable into the back box, leaving at least 6” (152mm) of cable
inside the back box for connection to the unit’s lead wires.
CRÉÉ PAR | CREATED BY:
MAINTENANCE AND OPERATION
CRÉÉ LE | CREATED ON:
MIS À JOUR | UPDATED:
N.B. The unit should be cleaned at least once a year. All other repairs and maintenance other than those described in this guide should be
performed by qualified service personnel. In order for the warranty to be valid, the unit must be cleaned regularly.
TOLÉRANCES SI NON-SPÉCIFIÉ
Cut off power supply at circuit breaker/fuse and wait for the unit to cool down before cleaning.
L'INFORMATION CONTENUE DANS CE DOCUMENT EST
LINÉAIRE | LINEAR:
Use a soft rag for dusting. When cleaning, use only a damp rag and non-abrasive dish soap. Do not use abrasive or chemical cleaners because
they[ ±.76mm]
.XX = ±.03"
may damage the finish. If the unit is used in a very dusty location, use a vacuum brush to remove dust and other foreign objects from the grills. Note that
.XXX = ±.015" [ ±.38mm]
cigarette smoke could yellow the discharge grill and that the best way to prevent it is to clean the unit on a regular basis.
LA PROPRIÉTÉ DE STELPRO DESIGN. EN AUCUN CAS,
L'INFORMATION NE PEUT ÊTRE UTILISÉE, SAUF SOUS
AUTORISATION ÉCRITE DE STELPRO DESIGN.
THE INFORMATION IN THIS DOCUMENT IS THE
PROPERTY OF STELPRO DESIGN. IN ANY CASE, THE
N.B. There is an electrical current linked to the unit even if the thermostat is set to off. This means that there is a risk of electric
shock as longX:\03as R&D\Développem
EMPLACEMENT:
the unit is energized.
INFORMATION CAN'T BE USED, EXCEPT THE WRITTEN
CONSENT OF STELPRO DESIGN.
Do not use cleaning products identified
with these symbols:
5
INSUWH0315
TROUBLESHOOTING AND REPLACEMENT COMPONENTS
TROUBLESHOOTING
PROBLEM
DEFECTIVE PART OR PART TO CHECK
THE UNIT DOES NOT WORK
Defective thermostat or wrong thermostat setting
Open circuit breaker or fuse
Activated thermal protection
Faulty connections
THE UNIT RUNS CONTINUOUSLY
Defective thermostat or wrong thermostat setting
Heat losses greater than the unit’s capacity
THE ENCLOSURE IS EXTREMELY HOT
Defective thermal protection
Blocked air vents
Defective motor
THE UNIT CYCLES UNDER CONTROL OF THE THERMAL
PROTECTION (OVERHEAT INDICATOR)
Blocked air vents
Defective motor
OVERHEATING
Defective thermostat or wrong thermostat setting
Defective motor
THE BREAKER TRIPS WHEN THE HEATER IS TURNED ON
Faulty connections
Voltage higher than indicated on the nameplate
ELEMENTS ARE ON, BUT THE MOTOR DOES NOT WORK
Defective motor
THE DESIRED ROOM TEMPERATURE CANNOT BE
REACHED
One or more defective elements
Defective thermostat or wrong thermostat setting
Voltage lower than indicated on the nameplate
Heat losses greater than the unit’s capacity
Nº
DESCRIPTION
Nº
DESCRIPTION
KIT
THERMOSTAT
N.B. If you do not
solve the problem after checking these points, cut off the power supply at
the
main electrical panel
UWH02ZW
GRILLE
A
UWHT1
and contact
our 500
customer
service
(see the LIMITED WARRANTY section to obtain the phone
numbers). DESCRIPTION
(UNIPOLAIRE)
MOTEUR
À
1000W
Nº
DESCRIPTION
Nº
MO-001
KIT THERMOSTAT
(208/240
V)
KIT THERMOSTAT
1
M-UWH02ZW
GRILLE
B
UWHT2
A
UWHT1
(BIPOLAIRE) (UNIPOLAIRE)
CACHE-TROU
BLANC
MOTEUR
500
À
1000W
OF REPLACEMENT
COMPONENTS
SB-005 LIST
MANCHON DE
2
MO-001
KIT THERMOSTAT
(PLUG)
5/8''
(208/240 V)
C
UWHSAW
B
UWHT2
SURFACE (BIPOLAIRE)
CACHE-TROU
BLANC
ELF-250 3
ELEMENT
(KIT)
SB-005
MANCHON DE
PART #
REF. #
PART #C
DESCRIPTION
(PLUG) 5/8''
UWHSAW
BLA-002 4REF. # HÉLICE
5" 27° 4B DESCRIPTION
SURFACE
ELF-250
ELEMENT (KIT)
5
1
M-UWH02ZW
GRILL
2
BLA-002
HÉLICE 5" 27° 4B
MO-001
500 TO 1000 W (208/240 V) MOTOR
3
SB-005
5/8” WHITE PLUG
4
ELF-250
ELEMENT (KIT)
5
BLA-002
BLADE 5" 27° 4B
2
1
UWHT1
THERMOSTAT KIT (SINGLE POLE)
B
UWHT2
THERMOSTAT KIT (DOUBLE POLE)
A
2
3
4
A
4
B
A
B
5
5
6
# PIÈCE | PART #:
CRÉÉ PAR | CREATED BY:
CRÉÉ PAR | CREATED BY:
CRÉÉ LE | CREATED ON:
MIS À JOUR | UPDATED:
2013-03-25
# PIÈCE | /PART
#:
2013-04-18
aferland
DESCRIPTION:
INSUWH0315
WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY
LIMITED WARRANTY LIMITED WARRANTY
This limited warranty is offered by Stelpro Design inc. (“Stelpro”) and applies to the following product made by Stelpro: UNIWATT UWH model. Please
read this limited warranty carefully. Subject to the terms of this warranty, Stelpro warrants its products and their components against defects in
workmanship and/or materials for the following periods from the date of purchase: 2 years. This warranty applies only to the original purchaser; it is nontransferable and cannot be extended.
CLAIM PROCEDURE
If at any time during the warranty period the unit becomes defective, you must cut off the power supply at the main electrical panel and contact 1) your
installer or distributor, 2) your service center or 3) Stelpro’s customer service department. In all cases, you must have a copy of the invoice and
provide the information written on the product nameplate. Stelpro reserves the right to examine or to ask one of its representatives to examine
the product itself or any part of it before honoring the warranty. Stelpro reserves the right to replace the entire unit, refund its purchase price or repair a
defective part. Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and carried out by persons
authorized by Stelpro.
Before returning a product to Stelpro, you must have a Stelpro authorization number (RMA). To obtain it, call the customer service department at: 1-800-363-3414 (electricians and distributors - French), 1-800-343-1022 (electricians and distributors - English), or 1-866-766-6020 (consumers).
The authorization number must be clearly written on the parcel or it will be refused.
CONDITIONS, EXCLUSIONS AND DISCLAIMER OF LIABILITY
This warranty is exclusive and in lieu of all other representations and warranties (except of title), expressed or implied, and Stelpro expressly disclaims and
excludes any implied warranty of merchantability or implied warranty of fitness for a particular purpose.
Stelpro’s liability with respect to products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever,
whether based on contract, tort or other theories of law, with respect to goods or services furnished by it, or any undertakings, acts or omissions relating
thereto. Without limiting the generality of the foregoing, Stelpro expressly disclaims any liability for property or personal injury damages, penalties, special
or punitive damages, damages for lost profits, loss of use of equipment, cost of capital, cost of substitute products, facilities or services, shutdowns,
slowdowns, or for other types of economic loss or for claims of a dealer’s customers or any third party for such damages. Stelpro specifically disclaims all
consequential, incidental and contingent damages whatsoever.
This warranty does not cover any damages or failures resulting from: 1) a faulty installation or improper storage; 2) an abusive or abnormal use, lack of
maintenance, improper maintenance (other than that prescribed by Stelpro) or a use other than that for which the unit was designed; 3) a natural disaster
or an event out of Stelpro’s control, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage, flooding, water
damages, etc. This warranty does not cover any accidental or intentional losses or damages, nor does it cover damages caused by negligence of the user
or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation.
The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price, at the discretion of Stelpro. Any parts replaced or
repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty period. This warranty
will be considered null and void and Stelpro will have the right to refuse any claims if products have been altered without the written authorization of
Stelpro and if the nameplate numbers have been removed or modified. This warranty does not cover scratches, dents, corrosion or discoloration caused
by excessive heat, chemical cleaning products and abrasive agents. It does not cover any damage that occurred during the shipping.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations on
how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may have
other rights which vary from state to state or from province to province.
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED
LIMITED WARRANTY LIMITED WARRANTY
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
7
INSUWH0315
Download PDF
Similar pages