KJtchen_kJd
®
COMPACTOR
For questions
about features, operation/performance,
parts, accessories
or service, call: 1-800-422-1230
or visit our website at
www.kitchenaid.com
In Canada, for assistance, installation
or service, call: 1-800-807-6777
or visit our website at www.KitchenAid.ca
Table of Contents ...........................................................................................................
9871780C
2
TABLE OF CONTENTS
COMPACTOR
SAFETY ..................................................................
3
INSTALLATION INSTRUCTIONS .................................................. 4
Unpacking ....................................................................................
4
Location Requirements ................................................................
4
Electrical Requirements ............................................................... 5
Freestanding and Undercounter Installation ............................... 6
Changing the Custom Panel ........................................................ 7
COMPACTOR USE .........................................................................
9
How Your Compactor Works ....................................................... 9
Loading .......................................................................................
10
WHISPER QUIET TM Plus System ............................................... t0
Starting Your Compactor ........................................................... 10
Using Solid (Locked) Cycle ........................................................ 10
Using the Air Filter or Freshener ................................................
Removing a Filled Bag ...............................................................
Installing a New Bag ...................................................................
COMPACTOR CARE ....................................................................
11
11
11
12
Changing the Air Filter or Freshener .......................................... 12
Cleaning ......................................................................................
12
TROUBLESHOOTING ..................................................................
14
ASSISTANCE OR SERVICE ......................................................... 15
In the U.S.A ................................................................................
15
In Canada ...................................................................................
15
Accessories ................................................................................
15
WAR RANTY ..................................................................................
16
COMPACTOR SAFETY
Your
safety and the safety of others
are very
important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All
follow the safety alert symbol and either the word "DANGER" or
Thissafety
is themessages
safety alertwillsymbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
iMPORTANT SAFETY iNSTRUCTiONS
WARNING:
When using an electrical appliance, basic precautions
should always be followed,
including the
following:
m Read all instructions
before using the compactor,
Close supervision is necessary when used by or
near children. Do not allow to be used as a toy, or
to run unattended at any time. Lock Key Switch
when not in use and store key out of reach of
children.
m Do not compact toxic or volatile flammable material
such as oily rags and insect sprays. Do not compact
lighted cigarettes, cigars, or other hot or burning
items. Do not overload the compactor.
m
Do not touch moving parts.
Do not take apart the compactor. Incorrect
reassembly can cause electric shock when
subsequently used.
m
Do not operate with a damaged cord set, plug,
motor, or after damage in any manner. Have the
compactor examined, repaired or adjusted by an
authorized serviceperson.
Handle a loaded trash bag with care. Sharp objects
can pierce the bag and cause injury. Do not
overload trash bag with heavy material such as
glass.
Use only for intended use as described in this
manual. Do not use other than manufacturer's
recommended attachments.
m This compactor
is intended for household use only.
SAVE THESE INSTRUCTIONS
INSTALLATION
Installer:
Leave Use and Care Guide with the homeowner.
INSTRUCTIONS
3.
Homeowner: Keep Use and Care Guide for future reference and
for local electrical inspector's use, if required.
Place the 2 corner posts from the carton on the floor near the
compactor. Open the compactor drawer and remove any
shipping materials or other items from the drawer. Do not
remove the compactor bag. Grasp the handle and raise the
front of drawer until it clears the drawer stops. Grasp sides of
drawer and lift drawer out of compactor. Place the drawer on
the 2 corner posts.
Excessive Weight Hazard
Use two or more people to move and install
compactor.
Failure to do so can result in back or other injury.
m
IMPORTANT:
•
Do not grasp console to move compactor.
•
Begin in the room where the compactor will be located.
1.
Remove compactor from shipping carton. Remove all
protective packaging materials such as tape and shipping
pads, Use a mild detergent and warm water to remove waxy
residue caused by protective shipping material. Dry
thoroughly with a soft cloth. For more information, see
"Cleaning."
2.
Be sure the power cord is attached to the cord clip on the
rear of the compactor.
4.
Place the other 2 corner posts on the floor to the side of the
compactor. Grasp the sides of the compactor cabinet and put
compactor on its side on top of the corner posts, Remove the
shipping base from the bottom of the compactor.
A. Leveling legs
B. Shipping base
A. Cord clip
Product Dimensions
341/8 ''
(86,7 cm)
%,
15"
(38,1
cm)
'
....24"
(61 cm)
Cutout Dimensions
Jl
E_ectrica_
34_/4 " min_
Ptug into
a grounded
Do not remove
Shock
Hazard
3 prong
out_et.
ground
prong.
Do not use an adapter.
(87cm)
A. Grounded eletrical outlet must be a minimum
of 3" (7.6 cm) away from surrounding cabinets
or nearby walls as shown. It can be placed
either to the left or the right side of the
compactor.
Clearance
Dimensions
r----3
o
B _
A. Leave 6" (15.2 cm) of clearance space to the right side of
the compactor in order to remove the compactor bags.
B. Leave 23" (58.4 cm) of clearance in front of the compactor
in order to fully open or remove the compactor drawer.
Do not use an extension
cord.
Failure to follow these
death, fire, or etectrica_
instructions
shock.
Recommended
Grounding
can result
in
Method
This compactor is for use on a single phase, 115-volt, 60 Hz, AC
only 15- or 20-amp fused and properly grounded circuit and is
equipped with a grounding plug as shown below. It is
recommended that a separate circuit serving only this appliance
be provided.
This compactor must be grounded while in use to reduce the risk
of electric shock. The compactor is equipped with a threeconductor cord and 3 prong grounding-type plug to fit the proper
grounding-type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Do not connect the
green (or green and yellow) wire to a live terminal,
NOTE: Proper installation is your responsibility. Make sure you
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
a qualified installer to assure that electrical installation meets all
national and local codes and ordinances.
Undercounter
NOTE: Installation hardware is not provided. See "Accessories"
for ordering conversion kit.
1.
Tools needed
Gather the required tools and parts before starting installation.
•
Level
•
•
Phillips No. 2 screwdriver
•
Tape measure
•
Scissors
•
Flat-blade screwdriver
•
Utility knife
•
Pliers
Measure the height of your kitchen cabinet opening. The top
of the compactor should be at least 1/8"(3 ram) from the top
of the kitchen cabinet opening.
The rear wheels are preset for a kitchen cabinet opening
height of 341/4'' (87 cm) (position 1).
%6" hex-head socket
wrench
To adjust for other kitchen cabinet opening heights:
•
Loosen self-tapping
hole in position 1.
•
Move the rear wheel and stud to position 2 or 3 as
needed for your kitchen cabinet opening measurement:
IMPORTANT:
•
Do not grasp control panel to move compactor.
•
Slide compactor onto cardboard or hardboard before moving
compactor across floor to avoid floor covering damage.
•
Installation
•
screw just enough to clear stud from
Position 2:341/4 '' to 347_6'' (87 to 87.5 cm)
Position 3:347_6 '' to 34%" (87.5 to 88 cm)
NOTE: To level the unit in position 3, you may need to
add shims under the front leveling legs.
Tighten screw. Repeat for other rear wheel.
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
Freestanding
Installation
Use pliers to lower leveling legs away from cabinet. With the
drawer still removed from the compactor cabinet, place level
inside on the floor of the cabinet. Check that the compactor is
level from front to back and side to side. Adjust the leveling
legs until the compactor is level.
A
O
A.
B.
C.
D.
Wheel bracket assembly
Compactor cabinet
Locating stud
Self-tapping screw (pivot)
J
2.
Move the compactor
3.
Plug into a grounded 3 prong outlet.
4.
Slowly move compactor into its final position. Check that
compactor is still level. Repeat Step 1 if necessary.
5.
Grasp sides of compactor drawer and place bottom of
drawer into tracks. Lift at the handle so drawer will go over
drawer stops. Close drawer. Check to see whether drawer
opens freely. If the toe plate rubs against floor, see "Adjusting
the Toe Plate" for further instructions.
2.
Use pliers to lower leveling legs away from compactor
cabinet. Adjust legs so there will be a 1/6"(3 mm) to 1/4"
(6.4 mm) space between the top of the compactor and the
top of the kitchen cabinet opening. Stand the compactor
upright.
3.
Remove the plastic plugs from the compactor
4.
Move the compactor
5.
Plug into a grounded 3 prong outlet.
6.
Determine whether you want the compactor cabinet or
drawer front flush with the kitchen cabinet face.
close to its final position.
cabinet top.
close to its final position.
Using 2 - #8 - 18 x %6" mounting screws (provided in
conversion kit), attach the retaining brackets (provided in
conversion kit) to the compactor cabinet top as needed. See
"Accessories."
NOTE: Installation hardware is not provided with full cabinet
models. See "Accessories" for ordering conversion kit.
•
If the compactor cabinet face is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through "1 ."
•
If the compactor drawer front is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through "3."
•
If the compactor is to be midway between "1" and "3,"
place the retaining bracket mounting screws through "2."
9=
j-
Grasp sides of compactor drawer and place bottom of
drawer into tracks. Lift at the handle so drawer will go over
drawer stops. Close drawer. Check to see whether drawer
opens freely. If the toe plate rubs against floor, see "Adjusting
the Toe Plate" for further instructions.
Adjusting
",%
the Toe Plate
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
A. Countertop
B. Retaining bracket (provided in conversion
Mark on each side of the toe plate the amount of toe plate
that rubs the floor covering.
2.
Remove the drawer from the unit. See Step 3 in the
"Unpacking" section.
3.
Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
4.
Use scissors or utility knife to cut toe plate along line.
5.
Replace drawer. If toe plate still rubs floor covering, repeat
steps 1-4.
kit)
7=
Slowly lift the front slightly and roll compactor
cabinet opening.
8.
Using 2 - #8 - 18 x 1/2"mounting screws (provided in
conversion kit), fasten the retaining brackets (provided in
conversion kit) to the countertop with the mounting screws.
Countertop
1.
into the kitchen
mounting
Custom
Panel with Handle (Model
KUCP021R)
Dimensions
Use these dimensions drawings to create a custom panel for use
without a trim kit. The panel should be 1/2"to %" (13 mm to
16 mm) thick.
NOTE: A thicker panel may need rounded front corners and a
cutout for access to the handle.
A. Countertop
B. Retaining bracket (provided in conversion kit)
C. Mounting screw (provided in conversion kit)
2313/16"
(60.5
NOTE: If retaining brackets cannot be attached to the
underside of countertop, attach mounting clips (provided in
conversion kit) to retaining brackets. Fasten compactor to
kitchen cabinet face with mounting screws through the
mounting clips.
Cabinet-face
mounting
15"
__
(3&1 ram)
A. Mounting clip (provided in conversion
B. Kitchen cabinet
kit)
C. Retaining bracket (provided in conversion kit)
D. Mounting screw (provided in conversion kit)
ram)
Installation
1.
Remove the mounting screws attaching the foot pedal to the
compactor, Remove foot pedal.
A. Mounting screws
B. Foot pedal
2.
Remove mounting screws attaching the toe guard to the
compactor. Remove toe guard.
3.
Remove the mounting screws attaching the decorative panel
to the compactor. Remove decorative panel and discard
mounting screws.
4.
Align the bottom of the custom panel with the bottom of the
drawer front,
5.
Secure the panel from the back using four #8 x 1" wood
screws as shown.
6.
A. Handle
B. Custom panel
C. Panel screw locations
D. Toe guard
E. Washer
Reinstall the toe guard using the existing screws and
1/2"washer. Then, reinstall the foot pedal.
F. Toe guard screw
Custom
Panel without
Handle (for all C and S models)
Dimensions
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be 1/2"(13 mm) min. thick.
25"
(63.5cm)
_38.1
15"cm)___
Installation
1.
7.
Remove the mounting screws attaching the foot pedal to the
compactor. Remove foot pedal.
Reinstall the toe guard using the existing screws and 1/2"
washer. Then, reinstall the foot pedal.
A. Mounting screws
B. Foot pedal
2.
Remove mounting screws attaching the toe guard to the
compactor. Remove toe guard.
3.
Remove the mounting screws attaching the decorative panel
to the compactor. Remove decorative panel and discard
mounting screws.
4.
Align the bottom of the custom panel with the bottom of the
drawer front,
5.
Secure the panel from the back using 4 - #8 x 1" wood
screws as shown.
6.
Attach a 15" x 1/2"quarter-round filler along the top of the
drawer front using glue or screws.
A. Custom panel
B. 15" x _ " quarter-round
C. Panel screw locations
D. Toe guard
E. Washer
F Toe guard screw
COMPACTOR USE
The compacting ram is the part of the compactor which
compresses the trash. The compacting ram does not go to the
bottom of the drawer. You will not see compacting of trash the
first few times you load the compactor.
NOTE: The compactor drawer should be more than 1/2full before
the compactor can begin to compress the load.
Load bulky trash, bottles, and cans in the center of the drawer.
Bottles or cans not placed in the center may become caught
between the ram and the drawer. The Drawer Monitor Switch
then senses a "misload" and causes the ram to return to the "up"
position without compacting.
You may hear a noise when glass breaks. Strong glass bottles
may not break at all. The trash in a full compactor bag will be
about 1/4the size of its original bulk.
_._-H_.tlli---
'''''
..,,,'''''
.,
,,'' i7'
IMPORTANT: Do not push items down into compactor
hands or feet.
with
NOTE: You will not see compacting of trash the first few times
you load the compactor. The compactor drawer should be about
1/2full before the compactor can begin to compress the load.
1.
The WHISPER QUIET Plus system helps to maintain a quiet
home environment during compactor operation.
TM
NOTE: The contents of the trash may affect the noise level of
your compactor. See "Compactor Use."
Open the drawer. Lift and pull the handle or press the toe bar
to open the drawer.
Press NORMAL (UNLOCKED) on the Compact Control. Turn
the Key-Knob to START, and then release it.
NOTE: Pressing the toe bar opens the container only 3" to 6"
(7.6 cm to 15.2 cm), depending on the load.
OFF
/_N
START
2.
2=
Place trash in compactor.
•
Wrap or cover wet or messy trash.
•
Do not compact items that may develop offensive odors
such as raw meat, fish, grapefruit rinds, disposable
diapers, or personal hygiene items.
•
Load bottles or cans on their sides in the center of the
drawer. Do not load bottles in an upright position.
The compactor
Compact
SOlid
Nepal
Locked
stops after completing
Unlocked
the cycle.
NOTE: When the compacting cycle is done, turn the Key-Knob to
OFF. Remove the Key-Knob and store it out of children's reach.
The Solid (Locked) cycle extends the use of a bag by putting
constant pressure on the trash to keep it from springing back.
Regular use of the Solid (Locked) cycle can increase bag
capacity up to 25 percent.
During the Solid (Locked) cycle, the ram will stay in the down
position for extra compacting. While the Solid (Locked) cycle is
operating, an indicator shows on the control panel. The drawer is
locked and cannot be opened when the ram is down. For best
results, use the Solid (Locked) cycle for at least 30 minutes at a
time.
To use Solid
3.
(Locked) cycle:
Press SOLID (LOCKED) on the Compactor Control. Turn the
Key-Knob to START, and then release the Key-Knob.
Close the drawer.
NOTE: The indicator on the control panel shows when the
Solid (Locked) cycle is in use.
OFF
N
START
Compact
SOlM
NermaJ
Locked
UnJecked
VV
2.
After 30 minutes or more, turn the Key-Knob to START to
raise the compacting ram OR press NORMAL (UNLOCKED).
NOTE: When the compacting cycle is done, turn the
Key-Knob to OFR Remove the Key-Knob and store it out of
children's reach.
10
L !!_!_
ii_ii
_i!iii!i:il
t il:_i_,_;:ii!!
¸_:!_
ii_i:
¸i̧i:_i!ii!ii:_i!!_
i_i_i_:
¸¸__ilil
i: _!ii:__i!!i_!i;
!i:!i_
_i!_
_i_i
__i:!!!
¸_i:
¸
The fan-powered charcoal Air Filter absorbs and minimizes odor.
The degree of odor in the compactor depends on the type of
trash placed in it. The length of time before the filter needs to be
replaced varies with the type of trash compacted. Under normal
use the filter should be replaced once or twice per year.
Press ON on the charcoal Air Filter control. The fan creates air
movement in the compactor for odor removal.
NOTE: The charcoal Air Filter works even when the Key-Knob
is in the OFF position.
2.
IMPORTANT:
Before installing a new bag, be sure:
To use the filter:
IMPORTANT:
fan.
Do not use any kind of bag other than those designed especially
for use in your compactor. Order replacement compactor bags
through your local dealer or by calling the toll-free number on the
cover or in the "Assistance or Service" section.
•
The drawer side is securely locked.
•
The container is clean and free of debris.
1.
Place folded bag into the drawer. Open bag and pull top
edges over the drawer top.
2.
Lock bag in place by pulling the four prepunched holes over
the bag retainer buttons. Holes will expand over the buttons
without damaging the bag.
3.
Press inside of bag against the drawer bottom, sides and
corners for a smooth fit.
The air freshener will work with or without the
Press OFF on the charcoal Air Filter control to turn off the fan.
_ir
F_|ter
Off
O_
When the trash is compacted to the top of the drawer, remove
the bag. If the bag is too heavy, compact less trash before
emptying it in the future.
IMPORTANT: Do not push items down into compactor
hands or feet.
with
1.
Pull the drawer completely open.
2.
Remove top of bag from bag retainer buttons. Pull up all four
bag cuffs. Close bag with twist tie provided.
3.
Push Side-Lock
4.
Lift out bag.
Latch down and tilt drawer side open.
11
COMPACTOR CARE
Your new compactor is designed to give you many years of dependable service. However, there are a few things you are expected to do
in order to properly maintain your compactor. This section will tell you how to clean and care for your compactor.
_iCiii:_
_i_i:_
_i_
i!iii_i
i_i_i_i
ii_
ii!ii!!i,
i_:
il__iii!!_
i_ ,_!!i!!_
i _ii
¸¸_
i!!:_:i
!iii:_i!!_
¸_i:_i_:_
!Ji
¸'_i:_iii:!_!i_
i!i__!i!!_ii_i
__i?
_i:
¸
It is recommended that you use either the charcoal air filter or the
air freshener in the filter compartment. The solid air freshener
system is an alternative to the air filter and is designed to control
odors that might develop in the trash.
Before cleaning the compactor, turn the Key-Knob (or KeySwitch) to the OFF & LOCK position and remove it.
NOTE: Any services other than those outlined in this section
should be performed by a designated service representative.
To order the correct replacement charcoal filters or air fresheners,
call the toll-free number listed on the cover or in the "Assistance
or Service" section.
1.
Insert fingertips in the air filter cover and pull until the side
tabs release. Then, lift the cover to release the bottom tabs.
Cleaning
1.
Wash exterior surfaces (including stainless steel) with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Rinse and dry thoroughly
with a soft cloth.
2.
Wipe up spills right away. Some foods can damage the finish
if left on the compactor surface.
Cleaning
2=
Remove the air filter by pulling the top edge of the filter. The
filter should pull out easily. Throw away used filter.
OR
Exterior Surfaces
Inside the Drawer
NOTE: You may want to wear protective gloves since there may
be bits of glass in the drawer.
1. Remove the bag. See the "Removing a Filled Bag."
2.
Press down on the lever-action lock (or Side-Lock
latch).
Remove the air freshener by simply lifting out of the filter
compartment. Throw away used freshener.
3=
3.
To replace air filter, push the replacement filter into place.
OR
To replace the air freshener, place the replacement in the filter
compartment.
4.
12
Insert the bottom tabs of the air filter cover and push in until
the side tabs snap into place.
Hold the lever-action lock down and tilt the side of the drawer
out until the lock clears the drawer front.
NOTE: If desired, the drawer side can be removed by tilting it
up, then lifting it out.
4.
Wash the interior of the drawer with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
5.
If the drawer side was removed, slide it back into the tilted
position.
6.
Press the lever-action lock (or Side-Lock Latch) down while
pushing the drawer side to the upright position.
7.
Latch the drawer side by pushing up the lever-action
Side-Lock Latch).
5.
Wash the inside of the cabinet with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
gloves since there may
6.
To replace the drawer, grasp it by the sides and insert the
rollers onto the tracks.
Pull the drawer out until it stops.
NOTE: Look to see how the drawer rollers move in the tracks.
It will be easier to replace the drawer after you have finished
cleaning.
7.
Lift the front of the drawer and push it in fully past the stops.
Cleaning
Inside the Cabinet
NOTE: You may want to wear protective
be bits of glass in the cabinet.
1.
lock (or
\
2.
Lift the front of the drawer to clear the stops.
3.
Grasp the drawer on the sides and pull it out the rest of the
way. Set the drawer down gently.
4=
Vacuum the inside of the cabinet. Liquid spills or wet trash
should be cleaned up by hand, or by using a vacuum
designed to pick up liquids.
Cleaning
the Ram
NOTE: You may want to wear protective
be bits of glass on the ram cover.
gloves since there may
1.
Wipe glass particles off of the ram cover with a cloth or paper
towels.
2.
Remove foods with a clean sponge or soft cloth and a mild
detergent in warm water. Rinse and dry thoroughly with a soft
cloth.
Cleaning
Before a Vacation
If you will be away for more than a couple of days, remove the
compactor bag. Remove the Key-Knob (or Key-Switch) and store
it out of children's reach.
13
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Trash is not compacting
•
The drawer won't open
Is the drawer less than half-full? Drawer must be more than
half full before trash is compacted,
Your compactor
won't
Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
•
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
•
Is the drawer completely closed?
and start the compactor again.
•
Is the Key-Knob turned all the way to START? Turn the
Key-Knob (Key-Switch) fully to START and release (on some
models). See "Starting Your Compactor."
To raise the ram on models with push button controls:
Press OFF, and then press ON. See "Starting Your
Compactor."
•
Is the Solid Cycle engaged? Drawer remains LOCKED until
you reset by lifting the foot pedal up.
Close the drawer firmly
There is not enough compaction
•
Did you press ON before pressing START? Press ON
before pressing START (on some models). See "Starting the
Compactor."
or force
Do you use the compacting
cycle frequently enough?
Compacting works best when only a few items are loaded.
Bottles don't break
•
14
Is the ram all the way up? Drawer will open only when ram is
fully raised.
To raise the ram on models with a Key-Knob (or KeySwitch): Turn the Key-Knob (Key-Switch) to START and
release. See "Starting Your Compactor."
operate
•
•
•
How often do you notice this? Bottles will not break every
time. The thickness of the bottle's glass and the content of
the trash load below it may keep the bottle from breaking.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
"Troubleshooting." It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement
parts
If you need to order replacement parts, we recommend that you
only use factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new KITCHENAID_appliance.
To locate factory specified parts in your area, call us or your
nearest designated service center.
Call the KitchenAid Customer eXperience Center
toll free: 1-800-422-1230
Our consultants
Our consultants
provide assistance with:
•
Features and specifications
•
Warranty information.
•
Referrals to local dealers.
•
Use and maintenance
•
Accessory and repair parts sales.
•
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid Canada designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further
on our full line of appliances.
procedures.
assistance
provide assistance with:
•
Features and specifications
•
Installation information.
•
Use and maintenance
•
Accessory and repair parts sales.
•
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
on our full line of appliances.
procedures.
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in the United States.
To locate the KitchenAid designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further
Call the KitchenAid Canada Customer Interaction Centre toll free:
1-800-807-6777.
assistance
If you need further assistance, you can write to KitchenAid with
any questions or concerns at:
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
If you need further assistance, you can write to KitchenAid
Canada with any questions or concerns at:
Customer Interaction Centre
KitchenAid Canada
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
To ensure the proper functioning of your compactor, use
KITCHENAID ®replacement parts only. To order replacement
parts or accessories, call 1-800-462-3819 and ask for the
appropriate part number listed below or contact your authorized
KitchenAid dealer. In Canada, call 1-800-807-6777.
Replacement
Parts
Replacement Bags - Call for Part Number.
Charcoal Air Filters - Order Part Number 4151750.
Air Fresheners (scent):
Order Part #9872166GA (Fresh Green Apple)
Order Part #9872166L (Lavender)
Order Part #9872166LG (Lemon Grove)
Conversion Kit for Freestanding
installation only):
Order Part #9870118
Unit (undercounter
15
KITCHENAID ®COMPACTOR WARRANTY
ONE-YEAR
LIMITED WARRANTY
For one year from the date of purchase, when this compactor is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KitchenAid Canada will pay for factory specified parts and repair labor costs to correct
defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.
KitchenAid or KitchenAid Canada will not pay for:
1.
Service calls to correct the installation of your compactor, to instruct you how to use your compactor, to replace household fuses, or
to correct household wiring.
2.
Repairs when your compactor
3.
Pickup and delivery. Your compactor
4.
Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products
approved by KitchenAid or KitchenAid Canada.
5.
Repairs to parts or systems resulting from unauthorized modifications
6.
7.
Replacement parts or repair labor costs for units operated outside the United States or Canada.
Charcoal Filters.
8.
In Canada, travel or transportation
is used in other than normal, single-family
household
use.
is designed to be repaired in the home.
expenses for customers
DISCLAIMER
not
made to the appliance.
who reside in remote areas.
OF IMPLIED WARRANTIES;
LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY
BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND
PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR
REPLACEMENT ACCORDING TO THE TERMS OF THIS LIMITED WARRANTY.
KITCHENAID
OR KITCHENAID
CANADA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Outside the 50 United States and Canada, this warranty
determine if another warranty applies.
does not apply. Contact
your authorized
KitchenAid
dealer to
If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be found
by checking the "Assistance or Service" section or by calling the KitchenAid Customer eXperience Center, 1-800-422-1230 (toll-free),
from anywhere in the U.S.A. In Canada, contact your designated KitchenAid Canada servicer or call 1-800-807-6777.
6/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your compactor to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the inside panel of the compactor
drawer.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
9871780C
© 2005. All rights reserved.
Tous droits r_serv_s.
7/05
® Registered Trademark/TM Trademark of KitchenAid, U.S.A., KitchenAid Canada licensee in Canada
® Marque depos_e/TM Marque de commerce de KitchenAid, U.S.A., Emploi licencie par KitchenAid Canada au Canada
Printed in U.S.A.
Irnprime aux E.-U.
Download PDF
Similar pages