Therm 8000 S - Bosch Thermotechnology in Africa.

Condensing Gas Water Heater
Therm 8000 S
6 720 680 174 (2015/11) ZA
Installation and operating instructions
Read installation manual prior to installation of this unit!
Read user manual before putting this unit in operation!
Observe the warnings in the manuals!
The installation room must fulfill the ventilation requirements!
Installation by an authorised person only!
2 | Index
Index
5.9
1
2
3
4
5
Safety information and symbology . . . . . . . . . . . . . . 3
1.1
Key to symbols . . . . . . . . . . . . . . . . . . . . . . . 3
1.2
Safety information . . . . . . . . . . . . . . . . . . . . . 3
5.10
Installation of the exhaustion accessory and
admission of air . . . . . . . . . . . . . . . . . . . . . .19
Filling the condensate trap . . . . . . . . . . . . . 20
6
Admission / exhaustion accessories
(accessory Ø 80/125 mm) . . . . . . . . . . . . . . . . . . . . .22
6.1
Admission/exhaustion accessories
(diameter in mm) . . . . . . . . . . . . . . . . . . . . .22
6.2
Fitting instructions . . . . . . . . . . . . . . . . . . . 23
6.3
Explanation of Symbols on Fitting
Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6.4
Approved flue systems . . . . . . . . . . . . . . . . 24
7
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . .
7.1
Connection . . . . . . . . . . . . . . . . . . . . . . . . .
7.2
Power cable . . . . . . . . . . . . . . . . . . . . . . . . .
7.3
Position of the fuses in control unit . . . . . .
27
27
27
28
8
Installation instructions . . . . . . . . . . . . . . . . . . . . . .
8.1
Factory regulations . . . . . . . . . . . . . . . . . . .
8.2
Measuring gas pressure . . . . . . . . . . . . . . .
8.3
Adjusting CO2 (carbon dioxide) . . . . . . . .
8.4
Program values . . . . . . . . . . . . . . . . . . . . . .
8.5
Control board diagnostics . . . . . . . . . . . . .
8.6
Fan speed adjustment . . . . . . . . . . . . . . . .
28
28
29
29
32
33
34
12
9
13
13
13
14
14
14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
Periodic maintenance tasks . . . . . . . . . . . .
9.2
Verify the fuses in the control board . . . . .
9.3
Condensing heat exchanger unit . . . . . . . .
9.4
Startup after maintenance . . . . . . . . . . . . .
36
36
37
37
39
10
Problem solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10.1
Problem/Cause/Solution . . . . . . . . . . . . . . 40
11
Functional scheme . . . . . . . . . . . . . . . . . . . . . . . . . . 44
12
Environmental protection . . . . . . . . . . . . . . . . . . . . 45
13
Warranty Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Technical Characteristics and Dimensions . . . . . . . 4
2.1
Declaration of conformity with relevant EEC
regulations . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.2
Explanation of Model Code . . . . . . . . . . . . . . 4
2.3
Package contents . . . . . . . . . . . . . . . . . . . . . 4
2.4
Description of the heater . . . . . . . . . . . . . . . 4
2.5
Optional accessories . . . . . . . . . . . . . . . . . . . 4
2.6
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.7
Appliance overview . . . . . . . . . . . . . . . . . . . . 6
2.8
Electrical diagram . . . . . . . . . . . . . . . . . . . . . 7
2.9
Technical data . . . . . . . . . . . . . . . . . . . . . . . . 8
2.10
Operational instructions . . . . . . . . . . . . . . . . 9
Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating instructions . . . . . . . . . . . . . . . . . . . . . . .
4.1
Description LCD Display . . . . . . . . . . . . . . .
4.2
Before operating the appliance . . . . . . . . .
4.3
Connect and disconnect the appliance . . .
4.4
Water temperature setting . . . . . . . . . . . . .
4.5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6
Registration of remote control
(accessory nº 7 709 003 756) . . . . . . . . .
4.7
Remote control operation
(accessory nº 7 709 003 756) . . . . . . . . .
4.8
Program button . . . . . . . . . . . . . . . . . . . . . .
4.9
"Priority" function . . . . . . . . . . . . . . . . . . . .
4.10
Purge the appliance . . . . . . . . . . . . . . . . . .
4.11
Reset button . . . . . . . . . . . . . . . . . . . . . . . .
4.12
Locked condition . . . . . . . . . . . . . . . . . . . . .
10
10
11
11
11
12
Installation instructions . . . . . . . . . . . . . . . . . . . . . .
5.1
Important remarks . . . . . . . . . . . . . . . . . . .
5.2
Selection of location for installation . . . . . .
5.3
Minimum distances . . . . . . . . . . . . . . . . . . .
5.4
Installation of fixing bracket . . . . . . . . . . . .
5.5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6
Water connection . . . . . . . . . . . . . . . . . . . .
5.7
Connecting the condensate water drain
to the appliance . . . . . . . . . . . . . . . . . . . . .
5.8
Gas connection . . . . . . . . . . . . . . . . . . . . . .
15
15
15
16
16
16
17
6 720 680 174 (2015/11)
18
18
Therm 8000S
Safety information and symbology | 3
1
Safety information and symbology
1.1
Key to symbols
Warnings
Warnings in this document are framed and
identified by a warning triangle which is
printed on a grey background.
Electrical hazards are identified by a
lightning symbol surrounded by a warning
triangle.
Keywords indicate the seriousness of the hazard in terms of the
consequences of not following the safety instructions.
• NOTICE indicates that material damage may occur.
• CAUTION indicates that minor to medium injury may
occur.
• WARNING indicates that serious injury may occur.
• DANGER indicates possible risk to life.
Important information
Important information in cases where there
is no risk of personal injury or material losses
is identified by the symbol shown on the left.
It is bordered by horizontal lines above and
below the text.
Additional symbols
Symbol
Meaning
▶
a step in an action sequence

a reference to a related part in the document or
to other related documents
•
a list entry
–
a list entry (second level)
Table 1
1.2
Safety information
If you smell gas:
▶ Close the gas valve.
▶ Open the windows.
▶ Do not operate any electrical appliances or switches (on/
off).
▶ Extinguish any fire.
▶ Go to a different location and call the gas supplier or an
authorised technician.
Therm 8000S
If you smell combustion gases:
▶ Turn off the heater (page 11).
▶ Open doors and windows.
▶ Notify a gas fitter.
Installation, modifications
▶ The installation may only be carried out by registered
installers and shall comply with the requirements of SANS
10087-1.
▶ The appliance must be installed along with
a low-pressure gas regulator.
▶ The assembly and modifications during the installation of
the heater can only be performed by an authorised
installer.
▶ Do not modify the pipes which conduct combustion gases.
▶ Do not close or reduce air circulation vents.
Maintenance
▶ We recommend to have the system regularly serviced in
order to ensure that it functions reliably and safely.
▶ The installer is responsible for the safety and
environmental compatibility of the installation.
▶ The heater must be serviced annually.
▶ Only original spare parts must be used.
Explosive and highly inflammable material
▶ Do not store or use inflammable material (paper, solvents,
paints, etc) near the heater.
Combustion air and surrounding air
▶ To avoid corrosion, the combustion air and surrounding air
must be free from harmful substances (e.g. halogenated
hydrocarbons which contain chlorine and fluorine
compounds).
Handover to the user
When handing over the heating system, instruct the user in its
operation and operating conditions.
▶ Explain the operation - with particular emphasis on all
safety-related actions.
▶ Explain that conversions and repairs must only be carried
out by an approved contractor.
▶ Point out the need for inspections and maintenance for
safe and environmentally-compatible operation.
▶ The installation and operating instructions must be given to
the user for keeping.
Safety of electrical appliances for
domestic use and similar purposes
The following requirements apply in
accordance with EN 60335-1 in order to
6 720 680 174 (2015/11)
4 | Technical Characteristics and Dimensions
prevent hazards from occurring when using
electrical appliances:
“This appliance can be used by children of 8
years and older, as well as by people with
reduced physical, sensory or mental
capabilities or lacking in experience and
knowledge, if they are supervised and have
been given instruction in the safe use of the
appliance and understand the resulting
dangers. Children must not play with the
appliance. Cleaning and user maintenance
must not be performed by children without
supervision.”
“If the power cable is damaged, it must be
replaced by the manufacturer, its customer
service department or a similarly qualified
person, so that risks are avoided.”
2
Technical Characteristics and
Dimensions
2.1
Declaration of conformity with relevant EEC
regulations
This appliance fulfills European directive requirements
2009/142/EEC, 92/42/EEC, 2006/95/EEC, 2004/108/EEC
and corresponds to the specifications described in the
corresponding EEC certificate of proof.
Model
Category
Type
2.2
GWHC 27
C
T
D
E
23
30
Table 3
[GWH]
[C]
[27]
[C]
[T]
[D]
[E]
[23]
[30]
2.3
•
•
•
•
•
•
•
•
•
•
•
•
•
GWHC 27 CTD E
II2H3B
C
•
•
•
•
Package contents
Description of the heater
Heater for wall-mounting
High power pre-mix compact burner with low NOx
emissions
Modulating Gas Valve with constant gas:air ratio control
LCD panel with back light
Failure codes for easy diagnostics and repair
Electronic ignition
Modulating water valve:
– Cold water temperature sensor
– Water flow sensor
Hot water temperature sensor
Built in frost protection
Safety devices:
– Flame failure device (ionization flame rod sensor)
– Back flow temperature sensor
– Inlet temperature sensor
– Outlet temperature sensor
– Room sealed box temperature sensor
– Over heat prevention (temperature limiter)
Power supply: 230 V, 50 Hz
IP X4 (protection against water drops)
2.5
•
Gas water heater
Condensing
Capacity (Liter per minute)
Room sealed box
Thermostatic
LCD
Electric ignition
Appliance adjusted for Natural Gas
Appliance adjusted for LPG
Gas heater
Support elements
Heater documentation
2.4
Table 2
6 720 680 174 (2015/11)
Explanation of Model Code
Optional accessories
Gas conversion kit (NG)
– Code nº 8 719 002 460
Freeze prevention kit
– Code nº 7 709 003 709
Outdoor kit
Therm 8000S
Technical Characteristics and Dimensions | 5
•
•
– Code nº 7 709 003 732
Cascading kit
– Code nº 7 736 500 272
Wireless remote control to operate with the appliance
2.6
•
– Code nº 7 709 003 756
High temperature kit
– Code nº 7 736 500 605
Dimensions
Fig. 1
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Front cover
Key pad
Cold water inlet: Ø ¾ “
Gas connection: Ø ¾ “
Hot water outlet: Ø ¾ “
Support bracket
Condensate water drain Ø 32mm
Therm 8000S
6 720 680 174 (2015/11)
6 | Technical Characteristics and Dimensions
2.7
Appliance overview
Fig. 2
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
Air admission adaptor (not included)
Condensing Heat Exchanger
Heat exchanger
Primary fan (Mixer)
Hot water sensor
Control unit
Flue Gas Adaptor (not included)
Room sealed box temperature sensor
CO2 / CO measuring point
Exhaust temperature sensor
Over heat prevention (temperature limiter)
6 720 680 174 (2015/11)
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
Anti-freeze heat element
Observation window
Ignition electrodes
Backflow temperature sensor
Ionization sensor
Secondary air fan
Pressure point gas valve
Cold water sensor
Gas valve
Key pad
Therm 8000S
Technical Characteristics and Dimensions | 7
2.8
Electrical diagram
16
L N
15
13
M
M
12
M
E
T=90°C
11
PS
20
10
T=104°C
19
9
T=110°C
8
FS
18
7
6
5
4
3
2
1
16
17
...
1 20
...
1
21
14
JP2
JP7
JP5
JP8
JP6
22
6720608917-02.1AL
Fig. 3
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[19]
[20]
[21]
[22]
Electrical scheme
Intlet water temperature sensor
Outlet water temperature sensor
Backflow temperature sensor
Cascading output connection
Cascading input connection
Ionization sensor
Water flow sensor
Room sealed box temperature sensor
Heat exchanger overheat sensor (104 °C)
Gas valve
Exhaust temperature sensor
Water valve
Primary fan
ON/OFF switch
Secondary fan
AC plug
Main connection
Ground post
Antifreeze kit connection
Fuse
Fuse
Therm 8000S
6 720 680 174 (2015/11)
8 | Technical Characteristics and Dimensions
2.9
Technical data
Technical characteristics
Symbol
Units
GWHC 27 CTDE
Nominal useful power
Pn
kW (Btu/h)
47,0 (160 370)
Minimum useful power
Pmin
kW (Btu/h)
6,0 (20 475)
kW
6,0 - 47,0
Power and flow
Useful power (adjustment range)
Nominal thermal flow
Qn
kW (Btu/h)
48,4 (165 295)
Minimum thermal flow
Qmin
kW (Btu/h)
6,0 (20 475)
LPG (Butane)
G30
kPa
3,0
Natural gas
G20
kPa
2,0
Gas data
Supply pressure
Consumption
LPG (Butane)
G30
kg/h
3,8
Natural gas
G20
m3/h
5,1
pw
bar
12
Water data
Maximum permissible pressure
Minimum operating pressure
bar
0,3
Minimum activation flow
pwmin
l/min
1,9
Maximum water flow with temperature rise of 25 °C
l/min
27
kg/h
79,3
Exhaust temperature at maximum power
°C
65
Exhaust temperature at minimum power
°C
28
Voltage
V
230
Frequency
Hz
50
Maximum power consumption
W
116
Type of protection
IP
X4D
Ambient temperature permitted
°C
0 - 50
Combustion products contents - DIN 4705
Exhaust gas flow
LPG - Butane
Temperature of gases at extractor grill
General Data
Noise
db (A)
59
Efficiency
%
100
Weight (excluding packaging)
kg
34
Table 4
6 720 680 174 (2015/11)
Therm 8000S
Regulation | 9
2.10 Operational instructions
Hot water
Open the gas and water valves and ensure that all joints are
hermetic.
Place the principle switch (Fig. 4, [1]) in the operating position
(chapter 4.3), so that the appliance is quickly ready for use.
When a hot tap is opened, the water flow sensor should be in
(Fig. 2, [2]) send a signal to the control unit. This signal
initiates the following:
• The fan starts working
• Simultaneously, sparks are produced and the gas valve
opens.
• The burner lights
• The ionisation electrode controls the state of the flame.
• The water temperature is controlled automatically by the
sensors/controllers according to the temperature
selected.
Security cut-off when safety period is surpassed
If a flame is not achieved within the stipulated security period
(35 sec), a security cut-off will occur.
The presence of air in the gas inlet pipe (when the appliance is
used after long periods of inactivity for example) may delay
ignition.
In this case, if the attempts to ignite go on too long, the security
mechanisms prevent operation.
Security cut-off due to excessive water heating
The control unit detects the heating temperature via a NTC
resistor located in the hot water exit tube and the temperature
limiter located in the heat exchanger. If it detects an excessive
temperature it provokes a security cut-off.
Restarting after security cut-off
To restart the appliance following a security cut-off:
▶ Press the reset key (Fig. 19).
3
Regulation
Any local by-laws and regulations pertaining to installation and
use of gas-heated appliances must be observed. Please refer to
the laws that should be attended in your country.
The installation may only be carried out by
registered installers and shall comply with the
requirements of SANS 10087-1.
Therm 8000S
6 720 680 174 (2015/11)
10 | Operating instructions
4
Operating instructions
Fig. 4
[1]
[2]
[3]
[4]
[5]
[6]
[7]
4.1
Main switch ON/OFF
Reset key
Program key
LCD panel
Temperature increase key/ programming key
Temperature decrease key / programming key
LED
Description LCD Display
CAUTION:
Do not use any cleaning aggressive or
corrosive agents to clean the window.
Fig. 5
6720608920-31 1AL
Fig. 6
Temperature indicator
Fig. 7
Error indicator
Power bar indicator (input)
6 720 680 174 (2015/11)
Therm 8000S
Operating instructions | 11
4.2
Before operating the appliance
CAUTION:
▶ The initial startup of the heater must be
realized by a qualified technician, who
will provide the client with all the
information necessary for its correct
usage.
Fig. 8
Locked condition indicator (only with remote
control)
▶ Confirm that the gas type of the heater matches the gas
supply you will be connecting the heater.
▶ Open gas valve.
Check for gas leaks at all joints.
▶ Open water valve.
Check for water leaks at all joints.
Fig. 9
Flame indicator
4.3
Connect and disconnect the appliance
Connect
▶ To start the appliance press the On/Off button.
Fig. 10
Solar mode indicator
Fig. 12
Disconnect
▶ To shut down the appliance press the On/Off button again.
4.4
Fig. 11
Remote control indicator
Therm 8000S
Water temperature setting
The temperature value indicated on the LCD
panel corresponds to the water temperature
at the appliance outlet.
6 720 680 174 (2015/11)
12 | Operating instructions
To regulate the emitted water temperature:
▶ Press the
obtained.
+
or
4.6
until the desired value is
Registration of remote control (accessory nº
7 709 003 756)
Only a qualified technician is allowed to install the additional
PCB that is supplied with the remote. Only after installation of
PCB the registration can be made.
The registration of the remote control must be done near the
appliance.
Hot water tap closed.
Turn OFF the appliance (Fig. 4, [1]).
Fig. 13
▶ Once the desired temperature is set, open the hot water
tap.
These appliance has an electronically
controlled gas valve that modulates the
burner input in response to both varying hot
water flow rates and/or changes in any
incoming and outgoing water temperatures.
4.5
▶ Press and hold the programming key (Fig. 4, [3]), press
ON/OFF button (Fig. 4, [1]) to connect the appliance.
Release programming key only when LCD displays “188”
The LCD displays the signal "P2".
▶ Press key
, until it displays the signal "P3".
▶ Press programming key again for about 1 second.
LCD panel displays one number and one rotating digit.
The number represents the remote control which is to be
registered, the first remote control will be registered with
number “0”, the second with number “1” and so on.
▶ Test the remote control in front of the electronic box by
simultaneously pressing the
and
control keys.
Operation
Turn ON the main swicth and the appliance is ready to work.
▶ When a hot water tap is opened, main burner ignites and
LCD displays indication
.
Fig. 15
6720608920-35.1AL
Fig. 14
LCD flashes until selected temperature is
reached.
6 720 680 174 (2015/11)
Activate new control
▶ Press both keys until the LCD panel stops flashing and
shows the indication “00”.
▶ Press ON/OFF button(Fig. 4 , [1]) to disconnect the
appliance .
Remote control is now deactivated.
Press the ON/OFF button to turn ON the
remote control and it’s ready to work.
Therm 8000S
Operating instructions | 13
4.7
Remote control operation (accessory nº 7
709 003 756)
This appliance fulfils European directive requirements 1999/
5/CEE (R&TTE) and corresponds to the specifications
described in the cor-responding CE certificate of proof.
▶ Press buttons
temperature.
Fig. 16
and
4.8
Program button
Program button can be used/programmed in the appliance and
in the remote control.
Programming "Program" function
Each remote control program button can
be programmed with different temperature
values according with the user needs. A
temperature value can be programmed in
the remote control and another value in the
appliance.
in order to reach requested
Remote control (temperature selection)
Program
NOTE: up to 6 remote controls can be
programmed for one single water heater,
each with a range distance of 30m.
CAUTION:
remote control is not a toy - do not allow
children to play with the remote control unit.
6720608920-32.1AL
Batteries replacement
▶ Remove the 2 screw from the remote control back.
▶ Open the cover.
▶ Remove the old batteries and correctly place the new ones.
▶ Close the remote control assuring that both screws are
tighten screwed.
CAUTION:
remote control can be used under the
shower
, however, it’s immersion must
not be forced
.
Precautions when using the batteries
• Do not dispose of batteries as domestic waste. Take them
to appropriate collecting places for recycling.
• Do not insert flat batteries.
• Only use the type of batteries indicated.
Therm 8000S
Fig. 17
"Program" key
▶ Press buttons
and
to select
temperature to be memorized.
▶ Press "Program" button for 3 seconds to save temperature.
The temperature is saved on "Program" when the LCD
panel stops blinking.
Using "Program" function
In order to select memorized temperature:
▶ Press "Program" key.
LCD shows pre-memorized temperature, which is now the
selected hot water temperature.
4.9
"Priority" function
PRIORITY is a function to prevents the user
from accidentally altering the water
temperature selected by another user.
6 720 680 174 (2015/11)
14 | Operating instructions
The appliance does not have a designated default priority.
Priority is attributed when the first user selects a temperature
(see chapter 4.4).
The following symbol appears for other users
.
The priority user may change the initial selection at any time.
Non-priority users cannot change the selection made by the
priority user.
The system resets priority function 5 minutes after last water
demand, returning to the initial state.
If the LCD shows the error symbol
do not shut off power
or unplug the heater. Follow instructions below to reset error
first.
Record the error code on LCD and consult chapter 10 to
identify the error.
To select priority
Any user may select temperature selection priority in the
following manner:
▶ Press one of the selection keys
5 seconds.
or
for
Priority cannot be selected when the
appliance is working.
Fig. 18
4.10 Purge the appliance
Error code
If there is a risk of freezing, proceed as follows:
After following instructions indicated in “Troubleshooting”
section,
▶ Close the cold water valve of the water heater.
▶ Open hot water taps to drain the water heater.
▶ Remove all the water contained inside of the appliance.
▶ press reset button firmly in order to return heater to normal
operation.
CAUTION:
The non accomplishment of the purgative of
the appliance whenever the freezing risk
exists, it can damage components of the
appliance.
The internal frost protection is designed to
provide protection for the water heater
down to approximately -10 °C for short term
conditions only. It will not protect the
appliance in areas where the temperature is
frequently expected to be below freezing.
The frost protection will not protect the
installation outside the appliance from
freezing. Suitable measures should be taken
to protect the installation against frost
damage.
Fig. 19
Reset button
If the problem persists, contact your installer.
4.12 Locked condition
This condition is only valid for appliances with one or more
remote controls installed.
4.11 Reset button
This appliance has a error codes system. The
visualization of these codes is made through
the LCD display. (Fig. 4, [4]).
6 720 680 174 (2015/11)
Therm 8000S
Installation instructions | 15
6720608920-33.1AL
Fig. 20
Locked condition
Whenever LCD shows
the temperature setting cannot
be adjusted because the appliance is in use by a user which
already selected a different temperature. Appliance will be
automatically unlock 5 minutes after closing hot water tap.
5
Installation instructions
DANGER: Explosion
▶ Always close the gas valve before doing
any work in gas components.
The installation, the electric connection, the
gas installation, the installation of the
exhaustion / admission conducts, as well as
the start up must be carried out by a qualified
technician.
The appliance can only be used in the
countries mentioned in the type plate.
CAUTION:
▶ Do not install the appliance where the
inlet water temperature is superior to
60 °C. In such cases we recommended
the installation of a mixer's valve in the
entrance of the appliance as prevention
measure.
5.1
Important remarks
▶ Install a gas shut-off tap as close to the appliance as
possible.
▶ After connection to the gas main, the appliance should be
carefully cleaned and tested for leaks; To avoid damage
from excess pressure in the valve gas regulator, this should
be carried out with the gas valve shut.
▶ Ensure that the appliance installed is suitable for the type
of gas provided.
▶ Ensure that the flow and pressures for the regulator
installed are those indicated for the consumption of the
appliance (see technical data in Table 4 ).
▶ A low-pressure gas regulator must be installed with the
appliance, in accordance with SANS 1237:2007.
5.2
Selection of location for installation
Considerations relevant to location
▶ Fulfil requirements specific to each country.
▶ The heater must not installed above a source of heat.
▶ Respect the minimum installation measurements indicated
in Fig. 21 .
▶ The appliance must not be installed in sites where the
ambient temperature is susceptible to drop below 0 °C.
Where there is a risk of freezing, disconnect and empty the
appliance (chapter 4.10).
If the above conditions are not possible, it´s
mandatory to use the kit anti-freeze nº 7 709
003 709.
▶ Assure that exists a socket for the electric connection at the
place were the appliance will be installed.
▶ Assure that exists at the place of the installation a sewer
point for the condensed waters.
Combustion air
▶ The air admission grill must be located in a well ventilated
area.
▶ To avoid corrosion, products such as solvents, inks,
inflammable gases, glue or domestic detergents containing
halogenic hydro-carbons or any product that might
provoke corrosion must not be stored near the air
admission grill.
Where these conditions are impossible to fulfil, an alternative
site for gas admission and exhaust must be selected.
Surface Temperature
The maximum surface temperature of the appliance is below
85 °C. Special protection measures are not required for
inflammable building materials or housings.
▶ Before installation, consult the gas company and current
legislation regarding gas appliance and site ventilation.
Therm 8000S
6 720 680 174 (2015/11)
16 | Installation instructions
5.3
Minimum distances
Determine the installation site with the following limitations in
mind:
▶ Maximum seclusion of all salient parts such as hoses and
pipes, etc.
▶ Ensure adequate access for maintenance work, respecting
the minimum distances indicated in Fig. 21.
▶ Fix the fixing bracket to the wall using the screws and plugs
provided.
A
6720608913-04.1AL
A
Fig. 21
Minimum distances
[A] Front > 2 cm, Side > 1 cm
5.4
Installation of fixing bracket
Before installing the fixing bracket, ensure
that the water/gas/exhaust connections are
guaranteed.
6720608913-05.1AL
Fig. 22
▶ Fix the fixing bracket to the installation point selected.
▶ Mark the position of the holes for the fixing bracket, make
sure that the fixing bracket is level, only then open the
holes.
5.5
Fix the fixing bracket
Installation
CAUTION: Possibility of damage caused by
foreign bodies!
▶ Purge all tubes to eliminate possible
foreign bodies.
▶ Remove appliance from packaging.
▶ Ensure that all indicated parts are included.
▶ Remove the plastic caps from the gas and water
connections.
6 720 680 174 (2015/11)
Therm 8000S
Installation instructions | 17
▶ Loosen the two Philips head screws located on bottom rear
of cover (Fig. 23).
CAUTION:
▶ Never rest the heater on the gas or water
connections.
For ease of installation it is recommended
that the water be connected followed by the
rest of the connections.
5.6
Water connection
▶ Mark the hot and cold water pipes in order to avoid
confusion.
Fig. 23
Loosen the two screws
▶ Lift front cover panel upward and remove.
Fig. 25
[1] Hot water
[2] Cold water
▶ Make the hot and cold water connection.
▶ In order to prevent problems caused by sudden inlet
pressure changes, the inclusion of an anti-return valve is
advised when installing the appliance.
Make sure that connections doesn’t obstruct
the condensate trap cover (Fig. 26, [1])
removal.
Fig. 24
▶ Fix the appliance in a vertical position.
Therm 8000S
6 720 680 174 (2015/11)
18 | Installation instructions
5.7
Connecting the condensate water drain to the
appliance
The condensate must be disposed of in
accordance with local codes.
5.8
Gas connection
DANGER: If local regulations are not follow
exactly, a fire or explosion may result causing
property damage, personal injury or loss of
life.
Only use accessories recommended in this
manual.
Fig. 26
The gas connection must fulfil local regulations.
[1] Condensate trap cover
[2] Condensate water drain
Use materials approved by the authority
having jurisdiction.
When the installation is effected with non-metallic, flexible
tubes for use with bottled Butane, the following should be
observed:
•
•
•
•
•
•
6720680174-01.1Av
Leave min. 10mm air gap
1 1/2” x 3/4” PVC Reducer
the tubes should be as short as possible and no longer than
1.5 m;
the tube should be to IPQ ET 1038 standard and fulfill all
applicable regulations;
it should be accessible for inspection along its entire
length;
it should not be located near heat sources;
bends and other obstructions should be avoided;
the ends should be secured with adequate accessories and
clamps;
▶ Tubes must be replaced every four years or whenever it
becomes dry or brittle;
▶ Ensure that the inlet tube is clean;
▶ Use the tube support accessory (provided) and an
appropriate clamp to make the gas inlet connections to the
appliance;
▶ Install a gas shut-off tap as near to the appliance as
possible;
▶ When the gas inlet is connected to the main, metallic tubes
must be used according to the applicable regulations.
– The accessory provided must be used to connect the
heater to the gas main.
– Tighten the threaded head on the gas inlet (Fig. 28,
[1]) and use the copper (Fig. 28, [2]) extremity to
solder the pipe to the main (Fig. 28, [3]).
Trap required
Fig. 27
Appliance drain installation
6 720 680 174 (2015/11)
Therm 8000S
Installation instructions | 19
▶ Tighten the 4 screws of the accessory of admission of air
Fig. 29, [2].
2.
2.
2.
2.
1.
Fig. 28
[1] Gas piping
5.9
Installation of the exhaustion accessory and
admission of air
It is mandatory the installation of the
accessories for the exhaustion / admission
of air, cod. 7 709 003 733 (system of
admission / exhaustion Ø80/80 mm).
For the installation of the accessory they should be following
the manufacturer's instructions.
6720608920-24.1AL
Fig. 29
WARNING:
▶ This appliance is required to be
connected to a dual duct flue system
incorporating separate paths for
provision of the combustion air and the
exhaust of the combustion products to
and from the exterior of the building.
Note the manufacturer's specific
instructions regarding installation of the
appliance.
5.9.1 Installation of the accessory of admission of air
To install the accessory of admission of air, proceed as follow;
▶ Put the gasket between the appliance and the accessory
Fig. 29, [1].
Therm 8000S
6 720 680 174 (2015/11)
20 | Installation instructions
5.9.2 Installation of the exhaustion accessory Ø 80mm
To install the accessory of the exhaustion accessory, proceed
as follow;
▶ Tighten the 3 screws of the concentric accessory.
▶ Put the gasket between the appliance and the accessory
Fig. 30, [1].
▶ Tighten the 3 screws of the exhaustion accessory Fig. 30,
[2].
1
2
2.
2.
2.
6720680174-06.1Av
1.
Fig. 31
Concentric accessory
[1] Concentric accessory
[2] Accessory 8 705 507 042
5.10 Filling the condensate trap
DANGER:
Before the first start up of the appliance,
after a long period of inactivity or whenever
it proceeds to the cleaning of the
condensate trap;
6720608920-25.1AL
Fig. 30
5.9.3 Installation of the concentric accessory - Ø80/125
mm
To install the concentric accessory, proceed as follow;
▶ Put the blue gasket provided with the appliance between
the appliance and the accessory.
6 720 680 174 (2015/11)
▶ Fill the condensate trap with water, to
prevent that the exhaustion gases enter
in the division where the appliance is
installed.
The condensate trap can be filled before or
after connecting the vent pipe.
Therm 8000S
Installation instructions | 21
5.10.1 Filling the condensate trap before vent pipe
installation
▶ Fill the condensate trap by pouring approx.14 oz. (400ml)
of water into the exhaust accessory on the top of the
appliance, see Fig. 32.
Fig. 32
▶ Fill the condensate trap by pouring approx.14 oz. (400ml)
of water into the top of the drain tube. To avoid damage to
the appliance use a funnel in this operation, see Fig. 34.
Filling the condensate trap at start up
5.10.2 Filling the condensate trap after vent pipe
installation
Please proceed as follows;
▶ Remove front cover, see Fig. 24.
▶ Open the four clips and remove the combustion cover.
▶ Remove the clip and disconnect the drain tube, see Fig. 33.
6720801993-15.1V
Fig. 34
Filling the condensate trap after installation.
After appliance has been out of use for a long
time or after cleaning the siphon, refill the
condensate trap with water.
6720608948-05.1AL
Fig. 33
Therm 8000S
6 720 680 174 (2015/11)
22 | Admission / exhaustion accessories (accessory Ø 80/125 mm)
6
Admission / exhaustion accessories
(accessory Ø 80/125 mm)
6.1
Admission/exhaustion accessories (diameter
in mm)
DANGER: Make sure that all flue
connections are tighten sealed.
▶ Failure to follow this requirement may
cause dangerous exhaust gases to
enter living space which may result
causing personal injury or loss of life.
Once is done the connection of the vent
pipes it always necessary to verified and
guaranteed that is sealed.
6.1.1 Concentric pipe admission /exhaustion Ø80/125 mm
Type
AZB 918
Description
TTNº
Horizontal basic Kit with 1300mm - Ø80/125
7 719 002 848
AZB 604/1
Concentric pipe with 500mm - Ø80/125
7 719 002 763
AZB 605/1
Concentric pipe with 1000mm - Ø80/125
7 719 002 764
AZB 606/1
Concentric pipe with 2000mm - Ø80/125
7 719 002 765
AZB 607/1
Elbow 90° - Ø80/125
7 719 002 766
AZB 608/1
Elbow 45° - Ø80/125
7 719 002 767
AZB 832/1
Elbow 30° - Ø80/125
7 719 002 768
AZB 919
Concentric vertical terminal Ø80/125, with 1393 mm + adapter with measuring point
7 719 002 849
AZB 371
Adapter for flat roof
7 716 050 046
AZB 921
Adapter with measuring point
7 719 002 851
AZB 922
Converter from Ø80/125 to Ø80/80, with measuring points
7 719 002 852
AZB 931
Vertical adapter with measuring point
7 716 780 184
Table 5
Flue accessories Ø80/125
Type
Description
TTNº
Accessories for the exhaustion / admission of air - Ø 80/80
7 709 003 733
Elbow 90º - Ø80
7 716 050 056
AZ 382
Elbow 45º - Ø80
7 716 050 057
AZ 383
Pipe Ø80 of 500mm
7 716 050 058
AZ 384
Pipe Ø80 of 1,000mm
7 716 050 059
AZ 385
Pipe Ø80 of 2,000mm
7 716 050 060
AZ 387
Terminal Ø80
7 716 050 062
AZ 378
Vertical terminal
7 716 050 053
AZ 381
Table 6
Flue accessories Ø80/Ø80
6 720 680 174 (2015/11)
Therm 8000S
Admission / exhaustion accessories (accessory Ø 80/125 mm) | 23
6.2
•
Fitting instructions
The permissible maximum flue/air pipe length, Lmax, for
the various possible flue configurations is specified in the
tables starting on chapter 8.6.
If the concentric flue/air pipe enters a chimney below
ground level, the appliance may register a fault and shut
down in cold weather due to ice formation. For that reason
such flue configurations should be avoided.
•
6.3
50
50
Explanation of Symbols on Fitting Diagrams
▶Lightly grease seal on flue side with solvent-free
grease (e.g. Vaseline) (Fig. 35).
50
2x
Ø 3mm
▶Push flue kit fully home (in this case: 50 mm
insertion depth) (Fig. 36).
6 720 604 873-18.1O
Fig. 36
▶Drill two 3-mm diameter holes in the combustion
air pipe. Maximum drilling depth 8 mm. It is
essential that flue pipe is not damaged! Fig. 37).
2x
Ø 3mm
2x
▶Secure joint with the screws supplied (Fig. 38).
Ø 3mm
Ø 3mm
360°
6 720 604 873-21.1O
Fig. 37
2x
6 720 604 873-17.1O
Fig. 35
6 720 604 873-22.1O
Fig. 38
Therm 8000S
6 720 680 174 (2015/11)
24 | Admission / exhaustion accessories (accessory Ø 80/125 mm)
6.4
Approved flue systems
6.4.1 Exhaustion type A3
Outdoor installation with accessory nº 7 709 003 732
Fig. 39
Ref.
Description
Minimum distance
Installation next to window; Installation next to door; Installation near of any open for air
recirculation.
> 1,250 m
D
Clearance to side wall
> 1,250 m
E
Clearance to roof or gutter
>1m
F
Clearance to the ground
> 1,200 m
G
Clearance to gas meter or regulator
> 1,500 m
A
B
C
Table 7
Installation clearances
6 720 680 174 (2015/11)
Therm 8000S
Admission / exhaustion accessories (accessory Ø 80/125 mm) | 25
6.4.2 Exhaustion type B23
Ø 135 mm est.
Ø 80 mm
Ø 80 mm
Ø 80 / 125 mm
Ø 80 mm
Ø 80 mm
6720608948-11.1AL
6720608920-36.1AL
Fig. 40
6.4.3 Exhaustion type C13
Ø 80 / 125 mm
6720608948-09.1AL
Fig. 41
Therm 8000S
6 720 680 174 (2015/11)
26 | Admission / exhaustion accessories (accessory Ø 80/125 mm)
6.4.4 Exhaustion type C33
Ø 135 mm est.
Ø 80 / 125 mm
³ 100
6720608948-10.1AL
³ 100
Fig. 42
6.4.5 Exhaustion type C43
Ø 80 mm
6720608920-28.1AL
Fig. 43
6 720 680 174 (2015/11)
Therm 8000S
Electrical connection | 27
6.4.6 Exhaustion type C53
Ø 135 mm est.
Ø 80 / 125 mm
Ø 80 mm
Ø 80 mm
6720608920-29.1AL
Fig. 44
7.1
7
Connection
Electrical connection
The electrical connection should be
according to current regulations regarding
domestic electrical installations.
▶ An earth connection is absolutely
essential.
DANGER: Risk of electric shock!
▶ Always disconnect the power supply to
the appliance at the mains before
carrying out any work on the electrical
systems and components.
▶ Connect the feed cable to an earthed power point.
All regulation, verification and safety mechanisms have been
rigorously tested in the factory and are ready for use.
CAUTION: Fuse protection!
▶ The appliance should have an
independent connection to the
electricity mains, protected by a
differential 30 mA switch and be
earthed. In areas subject to frequent
storms, a storm protector should be
installed.
Therm 8000S
7.2
Power cable
The appliance is provided with a labelled power cord and
earthed mains plug.
If the power cable gets damaged it must be
replaced by a genuine spare part.
6 720 680 174 (2015/11)
28 | Installation instructions
▶ Check the fuses in the printed circuit board, see Fig. 47,
[3].
1
6720608913-09.1AL
Fig. 45
7.3
2
Power cable connections
Position of the fuses in control unit
3
To check fuses, proceed as follows;
▶ Remove the front cover, see Fig. 23.
▶ Remove the three screws from the control unit (Fig. 46 e
Fig. 47, [1]).
6720608158-78.1AL
Fig. 47
Fuses position
▶ After checking the fuses, reinstall all parts in reverse order
(Fig. 47, [3]).
6720608920-38.1Av
Fig. 46
8
Installation instructions
8.1
Factory regulations
Sealed parts must not be interfered with.
▶ Remove the six screws from the back cover of the control
unit, see Fig. 47, [2].
Natural gas
Heaters designed for Natural gas H (G 20) are factory sealed for
delivery after the values on the characteristics panel have been
checked.
Heaters should not be ignited when the
connections pressure is less than 1,5 kPa
more than 2,5 kPa.
Liquid gas
Butane heaters (G30) are factory sealed for delivery after the
values on the characteristics panel have been checked.
6 720 680 174 (2015/11)
Therm 8000S
Installation instructions | 29
DANGER:
▶ The following operations must be
carried out by a qualified technician.
8.2
▶ Press and hold "Program" button and press ON/OFF button
to turn appliance ON (Fig. 49 ).
Measuring gas pressure
Confirm gas pressure after installation.
Connecting manometer
▶ Shut off gas supply.
▶ Remove the front cover (see Fig. 23).
▶ Loosen screw inside left test point fitting (do not remove)
and connect manometer tube to test point.
Fig. 49
Gas tuning mode
▶ As soon as '188' is displayed, release "Program" button
, and the display reads P2.
▶ Press + or
until P1 appears.
NOTE: While in this mode the appliance will
run constantly at maximum power and allow
maximum water flow.
For inlet gas pressure adjustment see values in Table 9 :
Fig. 48
Gas pressure test port (left tapping)
Static Pressure Test
▶ Turn gas supply back on.
▶ Record static gas pressure reading in Table 8.
Static Gas Pressure Reading
Pressure: ___________________ Date: ___________
Operating Gas Pressure Reading
Pressure: ___________________ Date: ___________
Table 8
Operating Pressure Test
▶ Press ON/OFF button to turn off the appliance.
Therm 8000S
Gas type
GN
Butane
kPa
2.0
3.0
Table 9
▶ Turn on high volume of hot water flow (at least 15 l/m) and
burner will light. If heater display reverts to P2, open more
hot water fixtures to allow sufficient flow. Press + until
P1 reappears on the display.
▶ Operate all other gas appliances on same gas piping system
at maximum output.
▶ Record lowest operating gas pressure reading in Table 8 .
Gas pressures lower than 2 kPa for Natural Gas or 3.0 kPa
for Butane will result in insufficient degree rise to the hot
water being used, reduced hot water volume, possible
error code faults and must be corrected.
Check gas pipes dimensions.
8.3
Adjusting CO2 (carbon dioxide)
The CO2 can only be adjusted by a certified
gas technician with a calibrated CO2
analyser.
6 720 680 174 (2015/11)
30 | Installation instructions
▶ Press
CAUTION:
One factor that may affect CO2 levels is
improper gas pressure.
▶ Check and adjust gas pressure, see
chapter 8.2.
When the gas pressure is correct:
▶ Press ON/OFF button to turn off the appliance.
▶ Remove plastic screw on the exhaust collar as seen in
Fig. 50.
+ or
button until “P1” appears on display.
Measuring CO2 (Combustion cover Installed):
▶ Open all hot water taps to achieve a flow rate of at least 15
l/m (1 tub and 2 sinks should be sufficient). If heater
display reverts back to P2, open more hot water fixtures to
allow sufficient flow.
▶ Press + until P1 reappears on the display.
▶ Record the CO2 reading in P1 in the Table 10 below.
Analyser reading may take several minutes to stabilize.
▶ Press + button until P2 appears. Unit will ramp down to
low fire and the water flow should decrease.
Program
CO2 values
P1
__________%
P2
__________%
Table 10
Adjusting CO2
Note: P1 adjustment will change the P2
reading. Confirm the P1 value BEFORE
adjusting the P2 level.
6720608920-18.1AL
Fig. 50
Measuring port
▶ Insert CO2 analyser probe into the measuring port. The tip
of the probe should be in the center of the flue pipe
(approx. 40mm inserted). Avoid air gaps between probe
and measuring port as they can alter readings.
▶ While holding the Program (P) button, press the ON/OFF
button to turn ON the heater (see Fig. 51).
If P1 CO2 level is out of range:
▶ Loosen yellow painted philips screw (Fig. 52, [1]) and
cover should rotate down (Fig. 52, [2]) revealing a
recessed brass slotted screw. (Fig. 52, [3]).
▶ Turning the slotted screw counter clockwise,
will raise P1 CO2 levels.
▶ Turning the slotted screw clockwise,
will lower P1 CO2 levels.
Adjustments to the slotted screw (P1) will
also change P2 CO2 levels.
▶ After bringing the P1 CO2 readings in proper range, press
the + button to enter the P2 mode.
Fig. 51
▶ While holding the Program P button, press the ON/OFF
button to turn ON the heater. As soon as ‘188’ flashes on
the display, release the Program button. The display should
now read P2.
6 720 680 174 (2015/11)
Therm 8000S
Installation instructions | 31
▶ Repeat steps 1 and 2 as necessary until CO2 values are
within the specified ranges.
As soon as the levels of CO2 are correct, verify the values of
CO corresponds to the limits of the Table 11 . If the values
exceed the limits, it is necessary to verify the ventilation
system and heat exchanger.
▶ Verify CO2 readings in P2 mode.
CO2 range (%)
Máx. CO level
(measured)
Natural gas
Max. input
P1
from 7.8% to 8.4%
< 250 ppm
Min. input
P2
from 2.0% to 2.4%
< 60 ppm
Butane
Fig. 52
Adjusting P1 CO2 level
If P2 CO2 level is out of range:
▶ Remove yellow painted #40 Torx cover from the front of
the gas valve, Fig. 52 . A plastic #40 Torx screw will be
revealed.
▶ Turning the plastic #40 Torx screw counter clockwise,
will lower P2 CO2 levels.
▶ Turning the plastic #40 Torx screw clockwise,
will raise P2 CO2 levels.
Note: This screw adjustment is very sensitive
and should be made in small increments. It
may take several minutes for readings to
stabilize.
Max. input
P1
from 10.2% to 10.8%
< 250 ppm
Min. input
P2
from 2.5% to 2.9%
< 60 ppm
Note: Values above are for climate controlled conditions.
Inputs such as gas pressure, heating value of the gas,
humidity and temperature of combustion air all impact CO
and CO2 values. Changes in these inputs can result in
different CO and CO2 values on the same appliance.
Table 11 CO2 & CO target numbers
End of adjustments
▶ Record the final values in Table 12 .
Program
CO2 values measured
P1
______________ %
P2
______________ %
Date
Table 12
Reassemble all parts in reverse order:
▶ Return slotted screw cover to original position and tighten
the philips screw, Fig. 52.
▶ Reinstall Torx protection cover, Fig. 53.
▶ Remove CO2 analyser probe and reinstall flathead screw
with gasket in exhaust collar.
▶ Press ON/OFF button to turn OFF the heater.
▶ Press ON/OFF button to turn ON the heater.
Heater is ready for normal operation.
6720608158-38.1AL
Fig. 53
Adjusting P2 CO2 level
▶ Verify both P1 and P2 CO2 readings are within the ranges
specified in Table 11 .
Therm 8000S
6 720 680 174 (2015/11)
32 | Installation instructions
8.4
Program values
CAUTION: Misadjusted program values
can lead to appliance malfunction, errors,
and service calls.
This section describes details on programming the appliance.
For most applications the factory default values will provide
robust and stable operation.
Program
Description
Factory default
Min
Max
Comment
P1
Maximum Power
N. Gas: 45
LPG: 39
21
N. Gas: 45
LPG: 39
See chapter 8.2.
Note: reducing P1 values below maximum
will reduce maximum power of the
appliance.
P2
Minimum Power
12
12
20
See chapter 8.2.
P3
Remote
Controls installed
_0
_0
6
See chapter 4.6.
P4
Access to
Diagnostic Mode
E
0d
10f
See chapter 8.5.
P5
Cascade Mode
nO
nO
CC
To activate the cascade mode it's
necessary to install the “kit cascade” (cod.
7 736 500 272)
P6
Temperature Unit
°C
°F
°C
See chapter 8.5.
P7
Appliance Type
nC
Condensing / Non-condensing
note: incorrect setting will cause errors.
On
dE: turns back light off after 60 seconds
from last button pushed.
P8
Back light
Cd
Cd
(Condensing)
(Condensing)
dE
dE
ON: turns backlight on permanently.
P9
Fan Purge
PH
Cascading type
Runs secondary fan and primary fan when
P9 is selected by depressing the “P” button
IC
IC
SC
This menu is only available when cascade
mode is selected CC.
PC
Master/Slave mode
CS
CS
Cn
Table 13
6 720 680 174 (2015/11)
Therm 8000S
Installation instructions | 33
8.5
Control board diagnostics
Diagnostic menu
To access the diagnostic menu, proceed as follow:
3F
3rd most recent error
▶ Press ON/OFF button to turn off the appliance.
▶ Press and hold "Program"
button and press ON/OFF
button to turn appliance ON.
▶ Release the
button when '188' appears on the
display. The display should read 'P2' when the program
button is released. If not, repeat process.
▶ Press and release the + button on the control panel
until the display reads 'P4'. You are now in the diagnostic
mode of the control board.
▶ When the display reads 'P4', press and release the
button once again and the display should read 'E.
▶ Use the + and
button on the control board to cycle
through different diagnostic modes available.
▶ Once in the selected diagnostic mode of your choice, press
and release the
button to display the diagnostic
information.
4F
4th most recent error
5F
5th most recent error
6F
6th most recent error
7F
7th most recent error
8F
8th most recent error
9F
9th most recent error
10F
10th most recent error
1P
2P
3P
H0
H1
H2
Appliance type (Cd or nC)
Appliance power (24 or 27)
Temperature range (H or C)
Numbers of hours - mode 0
Numbers of hours - mode 1
Numbers of hours - mode 2
Example: to read the flow rate in litters per minute while the
unit is flowing water, cycle to the '3d' mode and press the
button. A reading of 25 on the display would indicate the heater
is reading a flow rate of 2.5 litters/minute.
Once the information is obtained,
▶ Press the
button again to return to the diagnostic
mode menu.
▶ Press + or
buttons until the letter “E” appears on
the display, to leave the diagnostic menu.
▶ Press
button and in the display appear ‘P4’.
▶ Press ON/OFF button to turn off the appliance.
▶ Press ON/OFF button to turn ON the appliance.
Heater is ready for normal operation.
Diagnostic menu
Table 14
1) Only available condensing models
8.5.1 Working hours
To see how many hours the appliance has worked, please enter
the “Diagnostic menu”;
▶ Select the sub-mode “H0”.
Write the number that shows in the display.
▶ Select the sub-mode “H1”.
Write the number that shows in the display.
▶ Select the sub-mode “H2”.
Write the number that shows in the display.
After checking the sub-modes H0, H1 and H2, introduce the
values in the table below;
Working hours
E
Entry/Exit into sub-modes
0d
Set-point temperature (ºC)
Number in H0
______
_______ +
1d
Inlet water temperature (ºC)
Number in H1
______ (X 100) =
_______ +
2d
Outlet water temperature (ºC)
3d
Water flow (gallons/min) (l/min)
Number in H2
______ (X 10 000) =
_______ +
4d
Gas type (LP or NG)
(H0 + H1 + H2) = Total of hours
5d
Fan speed (Hz)
6d
Burner power (%)
7d
Maximum power (kW)
8d
Back flow temperature (ºC)
9d
Exhaust temperature (ºC)1)
1F
Most recent error/failure
2F
2nd most recent error
__________
Table 15
Table 14
Therm 8000S
6 720 680 174 (2015/11)
34 | Installation instructions
8.6
Fan speed adjustment
Exhaust
After installing the appliance, the minimum
power fan speed must be adjusted to
compensate for variation in vent pipe length.
Before adjusting the fan speed it is necessary to verify the
admission / exhaustion system, calculating the total length of
the exhaust pipes and quantity of elbows.
Pressure drop equivalence of the conducts and exhaustion
accessories
Equivalence in meters
1
Straight section length
___ x 1 =
________
2
90° elbows (qty)
___x 1 =
________
3
45° elbows (qty)
___x 0.5 =
________
4
30° elbows (qty)
___x 0.4 =
________
5
Sub-total:
________
Table 17
Intake
1
Straight section length
___ x 1 =
________
Ø80/80mm
Ø80/125mm
2
90° elbows (qty)
___x 1 =
________
30° elbow
0.4m
0.7m
3
45° elbows (qty)
___x 0.5 =
________
45° elbow
0.5m
1.5m
4
30° elbows (qty)
___x 0.4 =
________
90° elbow
1m
2m
5
Sub-total:
________
exhaust pipe per meter
1m
1m
6
Total equivalent vent length=
________
-
1.5m
Description
Horizontal vent kit
Table 16
8.6.1 Total equivalent vent length calculation Ø80 mm
How to calculate the total length of the exhaust conduct:
▶ Determine the total length of all straight sections of vent
pipe and enter in Table 17 , line 1.
▶ Count the number of 90° elbows used, multiply by 1m, and
enter that value in Table 17 , line 2. (Do not count nonconcentric terminals and first elbow used on intake and
exhaust ).
▶ Count the number of 45° elbows used, multiply by 0.5m,
and enter that value in Table 17 , line 3.
▶ Count the number of 30° elbows used, multiply by 0.4m,
and enter that value in Table 17 , line 4.
Table 18
Example
Exhaust:
•
•
5 units of 1m straight sections
1 unit of 1m straight sections
– Total length = 6 meters
•
2 - 90° elbows
Intake:
•
•
4 units of 1m straight sections
– Total length = 5 meters
2 - 90° elbows
Example table:
Exhaust
Do not count non-concentric terminals and
first elbow used on intake and exhaust.
▶ Repeat the previous procedure to calculate the total length
of the admission of air conduct. Insert values in Table 18 .
▶ Sum the total of the Table 17 with the total of the Table
18 and to put the result in the line 6 of the Table 18 .
This is the total equivalent vent length.
6 720 680 174 (2015/11)
1
Straight section length
6x1=
2
90° elbows (qty)
_1_ x 1 =
1
3
45° elbows (qty)
_0_ x 0.5 =
0
4
30° elbows (qty)
_0_ x 0.4 =
0
5
Sub-total:
6
7
Table 19
Therm 8000S
Installation instructions | 35
Example table:
Intake
1
Straight section length
_4_ x 1=
4
Concentric conducts
2
90° elbows (qty)
_1_ x 1 =
1
1
Straight section length
5x1=
3
45° elbows (qty)
_0_ x 0.5 =
0
2
90° elbow (qty)
_1_ x 2 =
2
4
30° elbows (qty)
_0_ x 0.4 =
0
3
45° elbow (qty)
_0_ x 1.5 =
0
5
4
30° elbow (qty)
_0_ x 0.5 =
0
12
5
5
Sub-total:
6
Total equivalent vent length=
Sub-total:
7
Table 20
Table 22
Note: Do not count terminals and first elbow used on intake and
exhaust.
Note: Do not count terminal and first elbow.
Total maximum length for concentric
conduts must not exceed 8 meters.
Total maximum length for separate tubes
(exhaust/admission) must not exceed 16
meters.
8.6.2 Calculation of the concentric conducts length Ø80/
125 mm
How to calculate the total length of the concentric conducts:
▶ Determine the total length of the concentric conducts and
enter in Table 21 , line 1.
▶ Count the number of 90° elbows used, multiply by 2m, and
enter that value in Table 21 , line 2.
▶ Count the number of 45° elbows used, multiply by 1.5m,
and enter that value in Table 21 , line 3.
▶ Count the number of 30° elbows used, multiply by 0.4m,
and enter that value in Table 21 , line 4.
5
8.6.3 Adjusting fan speed
After obtaining the total sum of the conducts, proceed as
follow:
▶ Press ON/OFF button into OFF.
▶ Press and hold "Program" button and press ON/OFF button
to turn appliance ON (see Fig. 54).
Do not count terminals and first elbow.
Concentric conducts
1
Straight section length
___ x 1 =
________
2
90° elbows (qty)
___x 2 =
________
3
45° elbows (qty)
___x 1.5 =
________
4
30° elbows (qty)
___x 0.7 =
________
4
Total equivalent vent length=
Table 21
Example
Concentric conduct:
•
•
4 units of 1m straight sections
1 unit of 1m straight section
– Total length = 5 meters
•
2 - 90° elbows
Therm 8000S
________
Fig. 54
▶ As soon as '188' is displayed, release "Program" button
, and the display should read P2.
▶ Press one time
to access the program P2. In the LCD
display is visible the attributed value (factory value: 12).
▶ Press + or
to choose the fan speed suitable with
your installation, see tab.23 for separate tubes admission/
exhaust Ø 80/80mm or Table 24 for concentric conducts
Ø 80/125 mm.
▶ Press and hold ( 5 sec.) “Program” button
until the
display flashes.
selected value is memorized.
6 720 680 174 (2015/11)
36 | Maintenance
Fan speed for separate tubes Ø80/80 mm
Mode
Conduct length 1)
Fan speed
P2
From 1 m until 6 m
12
from 6.1 m until 14m
13
from 14.1m until 16 m
14
Table 23
1) Total conducts lengths of Table 18 . Do not count with the
first elbow and the accessory of wind/rain protection.
Fan speed for concentric conducts Ø80/125 mm
Mode
Conduct length 1)
Fan speed
P2
From 1 m until 3 m
12
from 3.1 m until 7 m
13
from 7.1m until 8 m
14
Table 24
1) Total conducts lengths of Table 21 . Do not count with the
first elbow and the accessory of wind/rain protection.
Do not set P2 to greater then 14.
▶ Substitute dismantled joints and o-rings with new ones.
▶ Only the following lubricants must be used:
– On hydraulic parts: Unisilikon L 641 (8 709 918 413)
– Threaded joints: HFt 1 v 5 (8 709 918 010).
9.1
Periodic maintenance tasks
Functional checks
▶ Ensure that all safety, regulatory and checking elements
are in good working order.
Heat exchanger
▶ Inspect the heat exchanger.
▶ If it is dirty:
– Dismantle the chamber and remove the regulator.
– Clean the chamber with a pressurized water jet.
▶ If the dirt resists: soak soiled parts in hot water with
detergent and clean carefully.
▶ If necessary: de-scale the interior of the heat exchanger
and connection tubes.
▶ Reassemble the heat exchanger using new joints.
▶ Remount the regulator on its support.
Burner
WARNING: Burner damage!
The burner surface is very fragile.
9
Maintenance
To ensure that gas consumption and the environmental load
(pollution, etc.) remain as negligible as possible over a longer
period of time, we recommend that you assure to have the
appliance maintained on an annual basis (inspection) or if
necessary (maintenance).
Your appliance must only be serviced by a
qualified technician.
DANGER: Electrical discharge!
▶ Always disconnect the electrical current
(fuse, safety power switch) before
working on the electrical installation.
▶ Your appliance must only be serviced by a Bosch Technical
Assistance delegate.
▶ Use only genuine accessories.
▶ Order accessories according to the list of accessories
provided with the appliance.
6 720 680 174 (2015/11)
▶ Do not touch the burner surface, take
extra caution during the maintenance
operations!
▶ Inspect the burner annually and clean as necessary.
▶ Check the burner through the observation window if there
are liquids or fissures.
▶ Verify if the flame is stable and blue without signs of yellow
flames.
Yellow burner flames are an indication of
improper combustion. Assure that the
installation of the exhaustion conduct and
of admission of air fulfil the manufacturer's
requirements.
▶ Verify CO2 levels (see chapter 8.3) and correct it if
necessary.
Water filter
▶ Close the water inlet supply valve.
Therm 8000S
Maintenance | 37
▶ Clean the water filter, see Fig. 55 .
9.2
Verify the fuses in the control board
To check fuses, proceed as follows;
▶ Remove the front cover, see Fig. 23.
▶ Remove the three screws from the control unit (Fig. 56 and
Fig. 57, [2]).
6720608920-38.1Av
Fig. 56
Fig. 55
▶ Remove the six screws from the back cover of the control
unit, see Fig. 57 , pos.2.
[1] Water filter
1
2
3
6720608158-78.1AL
Fig. 57
Fuses position
▶ After checking the fuses, reinstall all parts in reverse order.
9.3
Condensing heat exchanger unit
The condensing heat exchanger unit must be
checked once a year by a qualified and
trained technician. If repairs are needed, the
repairs should be done by a certified
technician.
Therm 8000S
6 720 680 174 (2015/11)
38 | Maintenance
It is mandatory to propely replace the
gaskets and o-rings.
▶ Assemble the condensate unit and all other parts in reverse
order of disassembly.
9.3.1 Cleaning the condensate trap
WARNING: Material damage!
▶ Place a suitable container underneath
the appliance before unscrew the
condensate trap cover.
6720801916-04.1V
Fig. 58
Condensing heat exchanger unit
To clean the condensate trap proceed as follow;
▶ Open the condensate trap cover.
Condensing heat exchanger unit maintenance;
▶ Shut off power. Disconnect power cord.
▶ Dismantle all inlet, outlet pipes and the condensate tube
from the condensing heat exchanger unit.
▶ Remove the condensing heat exchanger unit from the
appliance by pulling it towards you.
▶ Dismantle all parts for inspection and cleaning.
Fig. 60
▶ Check and clean the condensate trap with clean water.
▶ Screw the condensate trap cover.
Fig. 59
Condensing heat exchanger
▶ Check the condensing heat exchanger for any obstruction.
▶ Flush the condensing heat exchanger unit with water.
▶ Replace all gasket and o-rings.
6 720 680 174 (2015/11)
9.3.2 Filling the condensate trap after the maintenance
works
After the condensate trap maintenance, it’s necessary to fill it
with water.
Proceed as follow;
Therm 8000S
Maintenance | 39
▶ Remove the clip and disconnect the drain tube, see Fig. 61.
▶ Check water level in the condensate trap, see Fig. 63 .
Fig. 61
▶ Fill the condensate trap by pouring approx.14 oz. (400ml)
of water into the top of the drain tube. To avoid damage to
the appliance use a funnel in this operation, see Fig. 62.
Fig. 63
▶ After filling reassemble all parts in reverse order.
9.4
Startup after maintenance
▶ Check all water and gas joints.
▶ Read chapter 4 "Operating instructions" and/or chapter 8
"Installation instructions".
▶ Check gas pressure (burner pressure).
▶ Make sure combustion cover is securely fastened.
▶ Ensure the exhaust vent adaptor is properly sealed.
▶ Check for gas leakage.
▶ Check for water leakage.
Fig. 62
Filling the condensate trap after installation
▶ Loosen the three screws of the control unit (Fig. 56).
▶ Put the control unit in service position by engaging its tabs
with the holes in the bottom horizontal sheet metal (see
Fig. 63).
Therm 8000S
6 720 680 174 (2015/11)
40 | Problem solving
10
Problem solving
10.1 Problem/Cause/Solution
To remove error code from the display, press
the reset button.
Display
Cause
Solution
A2
Fault in the flue gas limiter.
Temperature above 110 °C
inside the cabinet.
1. Check continuity of the flue gas limiter (normally closed).
2. Check for flue gas leakage around the top and bottom seals of heat
exchanger, use mirror to check around the rear as well as the viewing
window.
3. Check venting specifications are met. Long vent lengths, venting with
more than three elbows, blocked vent or combination venting may
cause this failure.
4. Check that flue gas limiter connector and spade connections are
secure.
5. Unplug heater and check the wiring harness connections on the
control board.
A3
Exhaust temperature sensor - 1. Check exhaust temperature sensor connection, see Fig. 2, [9].
happens if sensor is
2. Check sensor (< 100 ohm = short circuit).
disconnected or in short circuit 3. Check “P7” mode: The correct selection is “Cd”.
or appliance selection on “P7”
mode is not correct.
A4
Backflow temperature sensor
defect - happens if sensor is
disconnected or short circuit.
A7
Outlet temperature sensor fault 1. Check red wire connections at hot water temperature sensor. Clean
(Temperature below 0 °C or
terminals with an eraser. If badly corroded, replace sensor and wire
above 98 °C).
harness.
2. Sensor may trip if water temperature drops below 0 °C to protect
heater from freezing conditions. Any damage due to freezing conditions
is not covered under warranty.
3. Clean the water filter, any dirty in the faucets and also all the water
filters of the installation.
4. In areas where water has a high mineral content, periodic descaling
may necessary.
5. Check sensor.
1. Check backflow temperature sensor connection, see Fig. 2, [13].
2. Replace exhaust temperature sensor.
Table 25
* By installer or service technician only.
6 720 680 174 (2015/11)
Therm 8000S
Problem solving | 41
Display
Cause
Solution
(Flashing)
A9
Outlet temperature sensor not
sensing expected output
temperature. (Status message,
not an error)
1. Check that the sensor is firmly attached to the vertical section of the
hot water pipe.
2. Ensure that hot water sensor is not placed on any bends in the hot
water pipe or misreading may occur.
3. Check gas pressure. Low gas pressure may prevent the heater from
reaching desired output temperature.
4. Check supply voltage.
5. Possible defective control unit, call the Technical Assistance.
C6
Primary fan rotation too low in
operation.
1. Disconnect power supply cord and check wire connections on back
side of fan and the two connectors on the control board.
2. Check supply voltage.
3. Check venting specifications are met. Long vent lengths, venting with
more than three elbows, blocked vent or combination venting may
cause this failure.
4. Ensure intake and exhaust terminations maintain the required
clearances stated in the manual. Cross contamination between intake
and exhaust may cause the fan to alter its rotational speed.
5. Check gas pressure. Low gas pressure may cause the fan to change
its speed to meet desired temperature.
6. Possible defective control unit, call the Technical Assistance.
C7
No rotational speed sensor
signal from primary fan.
1. Disconnect power supply cord and check wire connections on back
side of fan and the two connectors on the control board.
2. Check supply voltage.
3. Possible defective component in fan or defective control unit, call the
Technical Assistance.
(Flashing)
CA
Water flow signal over
specified maximum value.
Water flow > 37 l/min.
1. Disconnect power supply cord and check wire connections on water
valve and the two connectors on the control board.
2. Excessive water pressure and flow. Ensure water pressure is less
than 10 bar and flow rate is below 37 Litters per minute.
E0
Software/hardware failure.
1. Disconnect power supply cord and check the two wire and ground
connections on control board as well as ground connection on heater
chassis.
2. Pressing the wrong combination of buttons on the control unit can
create confusion among the microprocessors inside. In this case, the
error code should not happen more than once or twice. Turn off the
water heater. Turn water heater back on and try resetting error code.
Use the reset button (
) to reset any error codes.
3. Possible defective control unit, call the Technical Assistance.
Table 25
* By installer or service technician only.
Therm 8000S
6 720 680 174 (2015/11)
42 | Problem solving
Display
Cause
Solution
E1
Hot water temperature sensor
(NTC) at the exit of the
appliance detect a high
temperature of the hot water.
Temperature > 85°C.
1. Check the correct position and fixation of the NTC sensor.
2. Check the electric connections and connectors of the hot water
temperature sensor. Clean terminals. If the terminals are rusted,
replace the sensor and cables. Check resistance (see Fig. 3, [2]).
3. Clean the water filter, any dirty in the faucets and also all the water
filters of the installation.
4. In areas where water has a high mineral content, periodic descaling
may necessary.
E2
Cold water temperature sensor 1. Check connector on wires coming from top of water valve for a secure
fault.
connection.
2. Sensor may trip if water temperature drops below 2°C. Protect
heater from freezing conditions as any damage due to freezing
conditions is not covered under warranty.
3. Check sensor.
E3
Exhaust temperature sensor the appliance will close the
burner and lock if it gets over
90°C. (only applied for
condensing unit).
1. Clean and check heat exchanger.
2. Clean and check condensing heat exchanger.
3. Reduce maximum power.
4. Reduce water temperature.
E4
Backflow temperature sensor
over 140 °C.
The appliance will close the
burner and lock (non-volatile).
1. Check inlet/outlet vent pipes.
2. Check if secondary fan connections are disconnected.
3. Check if venting specifications are met. Long vent lengths, venting
with more than three elbows, blocked vent or combination venting may
cause this failure.
4. Call the Technical Assistance.
E9
Overheat sensor (ECO) open
circuit (resets when cooler
temperatures are detected
104 °C).
1. Disconnect power supply cord and check wire connections on the
overheat sensor and the two connectors on the control board. see
Fig. 2, [7].
2. Check white wire connections at the overheat sensor. Clean terminals
with an eraser. If badly corroded, replace sensor and wire harness.
3. Check that venting specifications are met. Long vent lengths, venting
with more than three elbows, blocked vent or combination venting may
cause this failure.
4. Clean the water filter, any dirty in the faucets and also all the water
filters of the installation.
5. In areas where water has a high mineral content, periodic descaling
may necessary.
6. Unplug power supply cord to the water heater. Open a hot water tap
for several minutes to allow cold water to pass through heat exchanger.
Close hot water tap and disconnect lead wires to overheat sensor. Using
a multimeter, check continuity through overheat sensor contacts.
Replace sensor if open.
Table 25
* By installer or service technician only.
6 720 680 174 (2015/11)
Therm 8000S
Problem solving | 43
Display
Cause
Solution
EA
No flame ionization detected
with water flow.
1. Verify that all manual gas shut off valves are open.
2. Check gas type.
3. Check gas pressure.
4. Reset error code and open a water tap to cycle the heater in an effort
to purge air. Cycling hot water tap on and off multiple times may be
necessary. If heater still faults with EA error code, have a licensed gas
technician properly purge air out of the gas line leading to the water
heater.
5. Check three wire connections on the lower front of the heat
exchanger are secure.
6. Check venting specifications are met. Improper venting may cause
premature failure of the flame sensor rod.
7. Check that the minimum power fan speed has been adjusted to the
proper value. See chapter 8.6.
8. Observe inside the viewing window of the heat exchanger when a hot
water tap is opened. Sparking should be followed by a steady blue
flame. If flame is unstable/yellow with proper gas pressure, confirm CO2
readings.
EC
Ionization failure during
operation.
1. Check gas type.
2. Check gas pressure.
3. Check three wire connections to ignition group on the lower front of
the heat exchanger are secure.
4. Verify that venting specifications are met. Improper venting may
cause premature failure of the flame sensor rod.
5. Check that the minimum power fan speed has been adjusted to the
proper value. See chapter 8.6.
6. Check and adjust CO2 readings.
F7
Ionization error at standby.
1. Loose connection to the flame ionization rod. Verify that the thinner
wire leading from the control unit is securely connected to the set of
electrodes located on the lower front of the heat exchanger.
2. Flame ionization rod or control unit may be damaged. Call the
Technical Assistance.
FA
Gas leakage error, gas valve
circuit not closing properly.
1. Disconnect power supply cord and check wire connections on gas
valve and the two connectors on the control board.
2. Flow water out of a hot water tap above the minimum activation point
(1.9 l/m). Measure voltage at the gas valve wire plug connection. The
voltage should measure 24VDC between the left pair of wires and
24VDC between the right pair of wires when the unit is operating. If
voltage is not proper, call the Technical Assistance.
3. Gas valve may be defective, call the Technical Assistance.
Table 25
* By installer or service technician only.
Therm 8000S
6 720 680 174 (2015/11)
44 | Functional scheme
11
Functional scheme
IDLE
Water flow
> 0.5 gpm
(> 1.9 l/min)
(see WF calc.)
water tap
open?
See error code table
NO
YES
Fan speed = correct
Ionization = off
Temp. limiter = closed
Temp. sensors = ok
Over heat protection = ok
Appliance
ready to start?
YES
Fan speed
OK?
NO
NO
NO
waiting
time of 10s
passed?
YES
YES
Start sparking
Open the gas
valve
INPUTS:
- FANSPEED
- WATER TEMP.
- WATERFLOW
Ionization
detected?
OUTPUTS:
- FANSPEED
- WATERFLOW
NO
NO
NO
1st
Safety time
of 5s passed?
NO
2nd
Safety time of
5s passed?
YES
YES
3rd
Safety time
of 5s passed?
YES
YES
Hot water
delivered at
selected temp.
YES
safety
devices
OK?
See error
code table
NO
YES
water tap
closed
<0.5 gpm?
Post purge of
fan for 7 sec.
NO
YES
close one gas
valve
waiting
time of
1s passed?
flame off?
Stay blocked
till RESET
NO
YES
close second
gas valve
Water flow
Calculus
NO
YES
Post purge of
fan for 7 sec.
WF =
Minimum Power
(Set point - Inlet)
NO
6720608158-65.2V
0.5 GPM < WF < 1.6 GPM
(2 l/min < WF <6 l/min)
NO
WF > 1.6 GPM
(WF > 6 l/min)
YES
YES
Burner ON
Burner ON
Burner shutdown at:
Set point +9°F (5°C)
WF < 0.45 gpm ± 0.05 gpm
(WF < 1.7 l/min ± 0.2 l/min)
Burner shutdown at:
Set point +14°F (8°C)
WF < 0.45 gpm ± 0.05 gpm
(WF < 1.7 l/min ± 0.2 l/min)
Water flow procedure
Fig. 64
6 720 680 174 (2015/11)
Therm 8000S
Environmental protection | 45
12
Environmental protection
Environmental protection is a basic strategy of our company.
The quality of our products, profitability and environmental
protection are equal-ranking goals for us. Laws and regulations
concerning environmental protection are strictly observed. We
use the best possible technology and materials, under
economic considerations, to protect the environment.
Packaging
We participate in the recycling program of the respective
country to ensure optimal recycling.
All of our packaging materials are environmental-friendly and
can be recycled.
Old appliances
Old appliances contain valuable materials that should be
recycled.
The assemblies can be easily detached and synthetic materials
are marked accordingly. The assemblies can therefore be
sorted out and passed on for recycling or disposal.
Therm 8000S
6 720 680 174 (2015/11)
46 | Warranty Terms
13
Warranty Terms
Imported by:
Bosch Thermotechnology South Africa
Robert Bosch PTY (Ltd)
15th Road, Randjiespark
1685 Midrand
South Africa
Tel: +27 (0)11 651 9600
Bosch Gas Water Heaters have been thoroughly tested at the
factory and fulfills all standards valid in the country. Robert
Bosch (Pty) Ltd. provides warranty for this model and its
components, for the period of 24 months from the date of the
invoice, for any factory or material fault, with the following
exceptions:
•
•
•
•
•
•
•
When the installation of the product was done by
unauthorized people;
When the appliance or parts present changes or
malfunctions due to misuse of unauthorized people;
When the operation and use of the appliance is done under
conditions which are not allowed in the installation or
user's manual;
When there are changes to the warranty terms and
breakage of seals;
When damages are caused by transportation or accidents;
When damages are caused by inadequate gas or water
pressure;
When damages are caused by lack of maintenance or by
installing non-original parts;
Robert Bosch (Pty) Ltd. does not take over any responsibility
for personal damage, property damage or product damage
caused by installations done by unauthorized persons.
Therefore, we highly recommend that the installation is done
by a certified gas installer.
6 720 680 174 (2015/11)
Therm 8000S
| 47
Notes
Therm 8000S
6 720 680 174 (2015/11)
6720680174
Bosch Thermotechnology South Africa
Robert Bosch Pty (Ltd)
15th Road, Randjiespark
1685 Midrand
SOUTH AFRICA
Download PDF
Similar pages