Flush Mount PIR Motion Sensor

Flush Mount PIR Motion Sensor
PIR
HIR24
Tri-level Control for Independent DALI
Mechanical Structure
64.7
56
68.1
73.3
70mm
4
5
Ø8
3
(1) Sensor inset
(2) Lens pluggable
(3) Protection cover (covers the
Photocell
1
high-voltage terminals).
LED indicator
(4) Ceiling (drill hole Ø 70mm).
PIR
Rotary switch preset
Blind
*OUFMMJHFOU
1IPUPDFMM
2
%FUFDUJPO1BUUFSO
Note: the blind can be plugged to the cover for
59
59
reducing detection angle if necessary.
3PUBSZ4XJUDI
1SPHSBNJOH
0OF,FZ
$PNNJTTJPOJOH
RX
59
Infrared receiver
TZODISPOJ[BUJPO
DPOUSPM
"NCJFOUEBZMJHIU
UISFTIPME
Technical Data
Sensor Data
Input Characteristics
Model No.
Operating voltage
Stand-by power
Switched power
Warming-up
HIR24
220~240VAC 50/60Hz
<1W
Max. 20pcs devices, 40mA
Model No.
HIR24
Sensor principle
PIR detection
Detection range
(O x H) 10m x 3m
Detection angle
Mounting height
30s
360
O
5m (maximum)
Environment
Safety and EMC
EMC standard (EMC)
Safety standard (LVD)
Certification
EN55015, EN61000
O
O
Operation temperature
Ta: -20 C ~ +50 C
IP rating
IP20
EN60669-1, EN60669-2-1
Semko, CB, CE , EMC, LVD, SAA
IP20
www.hytronik.com
Hytronik PIR motion sensor
362
Lyskomponenter AS Sagmyra 2A, 4624 Kristiansand
t: +47 38 00 36 36 e: salg@lyskomponenter.no www.lyskomponenter.no
Functions and Features
1 Daylight Harvest
Light will not switch on
when natural light is
sufficient, even there is
motion detected.
The light switches on
automatically with
presence when natural
light is insufficient.
The light turns on at full or dims to maintain the lux level. The light output
regulates accroding to the level of natural light available.
Note:
The Light automatically dims down and
eventually turns off if the natural light lux
level exceeds the daylight threshold.
However, if the stand-by period is preset
at “+∞”, the fixture never switches off
but dim to minimum level, even the
natural light is sufficient.
The light switches off when
the ambient natural light is
sufficient.
The light dims to stand-by
period after hold-time and
stays on selected minimum
dimming level.
The light switches off
completely after the
stand-by period.
2 Manual Override
With the help of push-switch, this sensor can be over-ridden by the end-user to manually switch on/off the light, or adjust the target lux
level by push-switch, which makes the product more user-friendly and offers more options to fit some extra-ordinary demands:
* Short Push (<1s): on/off function;
On → Off: the light turns off immediately and cannot be triggered ON by motion until the expiration of pre-set hold-time. After this
period, the sensor goes back to normal sensor mode.
Off → On: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the daylight threshold or not.
* Long Push (>1s): adjust the target lux level by turning the light up or down. Both the adjustment on remote control and push switch
can overwrite each other. The last adjustment remains in memory.
Note: if end-user do not want this manual override function, just leave the “push” terminal unconnected to any wire.
3 Semi-auto Mode (Absence Detection)
It is easy to forget to switch off the light, in office, corridor, even at home. And in many other cases, people do not want to have a
sensor to switch on the light automatically, for example, when people just quickly pass-by, there is no need to have the light on. The
solution is to apply this “absence detector”: motion sensor is employed, but only activated on the manual press of the push-switch, the
light keeps being ON in the presence, and dims down in the absence, then switches off in the long absence.
Note: end-user can choose either function 2 or function 3 for application. Default function is manual override.
363
Hytronik PIR motion sensor
www.hytronik.com
Lyskomponenter AS Sagmyra 2A, 4624 Kristiansand
t: +47 38 00 36 36 e: salg@lyskomponenter.no www.lyskomponenter.no
4 Synchronisation Function
By connecting the “SYNC” terminals in parallel (see wiring diagram), no matter which sensor detects motion, all HIR24 in the group
will turn on the lights when surrounding natural light is below the daylight threshold. The detection area could be widely enlarged in
this way.
Settings (Remote Control HRC-11)
ON/
OFF
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
Reset Settings
Press button “RESET”, all settings go back to rotary switch settings.
Shift Button
Press button “Shift”, the LED on the top left corner will flash to indicate mode
selection. All values / settings in RED are valid for 20 seconds.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
SEMI-AUTO mode
1. Press button “Shift”, the red LED flashes for indication.
2. Press button “SEMI-AUTO/AUTO” to initiate semi-auto mode. The fixture is
manually turned on by pressing the push-switch, and goes off automatically in this
mode. (Absence detection mode)
HRC-11
Power output
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
Brightness +/Press the buttons to adjust the light brightness to reset the target lux level.
www.hytronik.com
Hytronik PIR motion sensor
364
Lyskomponenter AS Sagmyra 2A, 4624 Kristiansand
t: +47 38 00 36 36 e: salg@lyskomponenter.no www.lyskomponenter.no
Scene program - 1-key commissioning
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Daylight threshold
Press buttons in zone “ Daylight threshold” to set daylight sensor / target lux level at 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: 2lux / 10lux are disabled.
To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button first.
Ambient daylight threshold
1. Press button “Shift”, the red LED starts to flash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold / target lux level.
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button first.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, the fixture is 100% on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Stand-by dimming level
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
Dual tech & RF mode
All buttons are disabled.
365
Hytronik PIR motion sensor
www.hytronik.com
Lyskomponenter AS Sagmyra 2A, 4624 Kristiansand
t: +47 38 00 36 36 e: salg@lyskomponenter.no www.lyskomponenter.no
Rotary Switch Preset
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Channel
Rotary switch preset
Note: settings can also be changed by remote control
HRC-11. The last action controls.
Detection
range
Hold-time
Daylight
sensor
Stand-by
time
Stand-by
dim level
0
100%
5s
Disable
10s
10%
1
100%
1min
50Lux
5min
10%
2
100%
5min
50Lux
10min
10%
3
100%
5min
75Lux
+∞
10%
4
100%
5min
100Lux
+∞
10%
5
100%
5min
200Lux
+∞
30%
6
100%
10min
50Lux
30min
10%
7
100%
10min
75Lux
+∞
10%
8
100%
10min
100Lux
+∞
10%
9
A
100%
100%
10min
20min
200Lux
100Lux
+∞
1h
30%
10%
B
100%
20min
200Lux
+∞
30%
C
100%
30min
100Lux
+∞
10%
D
100%
30min
200Lux
+∞
30%
E
F
100%
30min
400Lux
+∞
50%
100%
5s
100Lux
10s
10%
Wiring Diagram
L
N
SY P N
NC
DALI driver
L
SY SY P N L
NC NC
DALI driver
HIR24
DALI
+
HIR24
DALI
-
+
-
SY P N
NC
DALI driver
L
HIR24
DALI
+
-
Detection Pattern
in
lk
wa
www.hytronik.com
ng
lki
wa
m
s8
ard
ow
gt
ss
ro
ac
m
10
Hytronik PIR motion sensor
366
Lyskomponenter AS Sagmyra 2A, 4624 Kristiansand
t: +47 38 00 36 36 e: salg@lyskomponenter.no www.lyskomponenter.no
Download PDF
Similar pages