590619D OR30SDPWIX userguide USCA(EN).

Freestanding cooker
OR30SDPWIX model
Installation instructions
and User guide
US CA
Contents
Safety and warnings
Installation instructions
First use
Setting the clock
Using your oven
Cooking functions
Cooking guide
Using the electronic timer
Automatic cooking
Induction cooktop introduction
Choosing the right cookware
Using your induction cooktop
Using your cooktop’s special features
Cooking guidelines
Using the warming drawer
Care and cleaning
Cooktop fault codes
Troubleshooting
Warranty and service
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please go to our website www.fisherpaykel.com or
contact your local Fisher & Paykel dealer.
1 US
CA
2
8
17
18
19
22
24
26
27
28
30
32
33
35
36
38
48
50
53
US
CA
2
Safety and warnings
Your safety is important to us.
Please read this information before using your cooktop.
Installation
WARNING!
Electrical Shock Hazard
Disconnect the appliance from the mains electricity supply before carrying
out any work or maintenance on it.
Connection to a good earth wiring system is essential and mandatory.
Alterations to the domestic wiring system must only be made by a qualified
electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Tipping Hazard
To reduce the risk of tipping the appliance, the appliance must be secured
by properly installed anti-tip device packed with the appliance.
- ALL COOKERS CAN TIP
- INJURY TO PERSONS COULD RESULT
- INSTALL ANTI-TIP DEVICE PACKED WITH COOKER
- SEE INSTALLATION INSTRUCTIONS
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions carefully before installing or using this product.
Save these instructions for the local electrical inspector’s use.
Please make this information available to the person responsible for installing your cooktop,
as it could reduce the installation costs.
Please leave these instructions with the appliance. Inform the customer to retain for future
reference.
Safety and warnings
3 US
CA
IMPORTANT SAFETY INSTRUCTIONS
This appliance is to be installed and connected to the electricity supply only by a qualified
technician in compliance with national codes, local regulations and according to these
instructions.
Electrical installation (including electrical grounding) must be done in accordance with the
National Electrical Code, ANSI/NFPA70 – latest edition and/or local codes. In Canada: Electrical
installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1
and/or local codes.
Failure to install the appliance correctly could invalidate any warranty or liability claims.
For personal safety, this appliance must be properly grounded.
Do not leave packaging elements (e.g. plastic bags, polystyrene foam, staples, packing straps)
within easy reach of children during or after installation, as these may cause serious injury.
Make sure you recycle the packaging material.
Before disposing of any appliance, make sure that it can no longer be used and that all hazardous
parts are removed or made harmless, so that children playing with the old appliance cannot
harm themselves.
Only genuine replacement parts may be used for servicing the appliance. These are available
from your nearest Fisher & Paykel Authorized Service Center.
To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space
located above the surface units should be avoided. If cabinet storage is to be provided, the risk
can be reduced by installing a rangehood that projects horizontally a minimum of 5 inches
beyond the bottom of the overhead cabinets.
This appliance is equipped with a four-prong grounding plug (NEMA 14-50P) for your protection
against shock hazard and should be plugged directly into a properly grounded socket. Do not
under any circumstances cut or remove the fourth (ground) prong from the power plug.
If an external electrical source is utilized, the appliance, when installed, must be electrically
grounded in accordance with local codes or, in the absence of local codes, with the national
Electrical Code, ANSI/NFPA 70.
The mains electricity switch should always be accessible.
When installing or removing the cooker for service, a rolling lift jack should be used. Do not push
against any of the edges of the cooker in an attempt to slide it into or out of the installation.
Pushing or pulling a cooker (rather than using a lift jack) also increases the possibility of bending
the leg spindles or the internal coupling connectors.
US
CA
4
Safety and warnings
Operation and maintenance
WARNING!
Electrical Shock Hazard
Do not cook on a broken or cracked cooktop. If the cooktop should break or
crack, cleaning solutions and spillovers may penetrate it and create a risk of
electrical shock. Contact a qualified technician immediately.
Failure to follow this advice may result in death or electrical shock.
WARNING!
Health Hazard
Persons with cardiac pacemakers or other electrical implants (such as insulin
pumps) must consult with their doctor or implant manufacturer before using
this appliance to make sure that their implants will not be affected by the
electromagnetic field.
Failure to follow this advice may result in death.
WARNING!
Cut Hazard
The razor-sharp blade of a cooktop scraper is exposed when the safety cover
is retracted. Use with extreme care and always store safely and out of reach
of children.
Failure to use caution could result in injury or cuts.
Safety and warnings
Operation and maintenance
WARNING!
Fire Hazard
Never leave the appliance unattended when in use. Boilover causes smoking
and greasy spillovers that may ignite.
NEVER try to extinguish a fire with water. Switch the appliance off at the wall
and then cover the flame with a lid or fire blanket.
Failure to follow this advice may result in overheating, burning, and injury.
WARNING!
Hot Surface Hazard
DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS OR THE INTERIOR
SURFACES OF THE OVEN. – Surface units may be hot even though they are
dark in color. Areas near surface units may become hot enough to cause
burns. During and after use, do not touch, or let clothing or other flammable
materials contact surface units or areas near units until they have had
sufficient time to cool. Among these areas are the glass surfaces within and
around the circles and the interior of the oven.
Never leave metal objects (such as kitchen utensils) or empty pans on the
cooktop as they can become hot very quickly.
Beware: magnetisable metal objects worn on the body may become hot in
the vicinity of the cooktop. Gold or silver jewellery will not be affected.
Keep children away.
Handles of saucepans may be hot to touch. Check saucepan handles do not
overhang other cooking zones that are on. Keep handles out of reach of
children.
Do not store flammable items in the oven or warmer drawer.
Failure to follow this advice could result in burns and scalds.
5 US
CA
US
CA
6
Safety and warnings
Operation and maintenance
IMPORTANT SAFETY INSTRUCTIONS
This appliance is designed and manufactured solely for the cooking of domestic (household)
food and is not suitable for any non-domestic application and therefore should not be used in a
commercial environment. The appliance warranty will be void if the appliance is used within a
non-domestic environment (i.e. a semi commercial, commercial or communal environment).
Proper installation — Be sure your appliance is properly installed and grounded by a qualified
technician.
Never use your appliance for warming or heating the room.
Do not leave children alone — Children should not be left alone or unattended in the area where
the appliance is in use. They should never be allowed to sit or stand on any part of the appliance.
Wear proper apparel — Loose-fitting or hanging garments should never be worn while using the
appliance.
User servicing — Do not repair or replace any part of the appliance unless specifically
recommended in the manual. All other servicing should be referred to a qualified technician.
Storage in or on appliance — Flammable materials should not be stored in an oven or near
surface units.
Do not use water on grease fires — Smother fire or flame or use dry chemical or foam-type
extinguisher.
Use only dry potholders — Moist or damp potholders on hot surfaces may result in burns from
steam. Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth.
Use proper pan size — This appliance is equipped with one or more surface units of different
size. Select utensils having flat bottoms large enough to cover the surface unit heating element.
The use of undersized utensils will expose a portion of the heating element to direct contact and
may result in ignition of clothing. Proper relationship of utensil to cooking zone will also improve
efficiency.
Never leave surface units unattended at high heat settings – Boilover causes smoking and greasy
spillovers that may ignite.
Utensil handles should be turned inward and not extend over adjacent surface units — To reduce
the risk of burns, ignition of flammable materials, and spillage due to unintentional contact with
the utensil, the handle of a utensil should be positioned so that it is turned inward, and does not
extend over adjacent surface units.
Do not cook on broken cooktop — If cooktop should break, cleaning solutions and spillovers may
penetrate the broken cooktop and create a risk of electric shock. Contact a qualified technician
immediately.
Clean cooktop with caution — If a wet sponge or cloth is used to wipe spills on a hot cooking
area, be careful to avoid steam burn. Some cleaners can produce noxious fumes if applied to a
hot surface.
Caution: Do not leave food or cooking utensils etc. in the oven during self-cleaning.
Safety and warnings
7 US
CA
Operation and maintenance
IMPORTANT SAFETY INSTRUCTIONS
CAUTION - Do not store items of interest to children in cabinets above an appliance - children
climbing on the appliance to reach items could be seriously injured.
If the appliance is malfunctioning, it will display an alert code: first note down the alert code (see
section ‘Alert codes’ in this manual), then contact your Authorized Service Center or Customer
Care to arrange for service. Do not use your appliance until it has been repaired by a Fisher &
Paykel authorized technician.
Never use your appliance as a work or storage surface.
Never leave any objects or utensils on the appliance.
Do not place or leave any magnetizable objects (eg credit cards, memory cards) or electronic
devices (eg computers, MP3 players) near the appliance, as they may be affected by its
electromagnetic field.
We recommend using plastic or wooden kitchen utensils for cooking with your induction cooktop.
Do not place or leave aluminum foil on the cooktop.
After use, always turn off the cooking zones as described in this manual. Do not rely on the pan
detection feature to turn off the cooking zones when you remove the pans.
Children or persons with a disability which limits their ability to use the appliance should have a
responsible and competent person to instruct them in its use. The instructor should be satisfied
that they can use the appliance without danger to themselves or their surroundings.
Do not use a steam cleaner to clean your cooktop.
Do not place or drop heavy objects on your cooktop.
Do not stand on your cooktop. Do not stand, sit or step or place heavy weights on the oven door.
Do not use pans with jagged edges or drag pans across the ceramic glass surface as this can
scratch the glass.
Do not use scourers or any other harsh/abrasive cleaning agents to clean your cooktop, as these
can scratch the ceramic glass.
Make sure the electrical cables connecting other appliances in the proximity of the cooker cannot
come into contact with the hob or become entrapped in the oven door.
Fire risk! Do not store flammable material in the oven or warming drawer.
Do not line the oven walls with aluminium foil. Do not place shelves, broiler pan, pans or other
cooking utensils on the oven floor.
Stand away from the cooker when opening the door. Hot air or steam which escapes can cause
burns.
Always use oven gloves or mitts when placing or removing items in the oven.
Never touch the appliance with wet hands.
After use, ensure the dials are all in the `OFF’ position.
The manufacturer declines all liability for injury to person or damage to property caused by
incorrect or improper use of the appliance.
Always turn off the mains power to the cooker prior to cleaning or maintenance.
US
CA
8
Installation instructions
Important!
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property
damage. Consult a qualified installer, service agent, or the gas supplier.
IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling or installing this appliance.
Tools needed for installation (not supplied with the appliance)
Screwdriver
2 - Wrench
Pencil
Tape
measure
Suitable protective
gloves
Hammer
Adjustable
wrench
Adjustable
pliers
Drill
Installation instructions
9 US
CA
Dimensions and clearances
The cooker must be installed no less than 2” (50 mm) away from any side walls which exceed the
height of the cooktop.
The cabinetry surrounding the cooker must be made of heat-resistant material and must be able
to withstand temperatures of 150 °F (65 °C) above room temperature.
Do not install the cooker near flammable materials (eg curtains).
If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.
Locating the area for electrical connection
5 7/16” (138 mm) to
6 1/8” (155.5 mm) (*)
Dotted line showing
the position of the
cooker when installed
Area for
electrical
connection
(*) Depending on
feet adjustment
Grounded outlet: should be located from the left to the right side of the range; from 5” 7/16 (138
mm) to 6” 1/8 (155.5 mm) [depending on feet regulation] from the floor.
The electric cord with 4-prong ground plug (NEMA 14-50P) shall have a minimum length of 48”
(1220 mm) beyond the back of the appliance.
10
Installation instructions
19 5/8” min.
(500 mm)
30” min.
(672 mm)
18” min.
(457 mm)
13” max.
(330 mm)
2” min.
(50 mm)
36”
(914 mm)
US
CA
0”(0 mm)
0” (0 mm)
The range CANNOT be installed directly adjacent to
sidewalls, tall cabinets, tall appliances, or other side vertical
surfaces above 36” (914 mm) high.
There must be a minimum of 2” (50 mm) side clearance
from the range to such combustible surfaces TO THE RIGHT
above the 36” (914 mm) high countertop; or there must be
a minimum of 2” (50 mm) side clearance from the range to
such combustible surfaces TO THE LEFT above the 36” (914
mm) high countertop.
Important!
One side (left or right) above the 36” (914 mm) high countertop
must always be kept clear.
The maximum upper cabinet depth recommended is 13”
(330 mm).
Any wall cabinet above the range must be a minimum of
30” (762 mm) above the countertop with a minimum width
of 30” (762 mm) and must be centered with the range.
Side wall cabinets above the range must be a minimum of
18” (457 mm) above the countertop.
Cooker overall dimensions [mm]
• height (without backguard):
MIN 35 21/32” (906 mm) MAX 36 11/32” (923 mm)
• product width:
29 7/8” (759 mm)
• depth:
24 13/64” (615 mm)
• backguard (height):
3” (76 mm)
Installation instructions
Moving the cooker
Important!
To prevent damaging the adjustable feet or lower
trim, ensure the cooker is always lifted by two
people.
Do not lift the cooker by the door handles.
DO NOT DRAG the cooker. Lift the feet clear of the
floor.
Take extra care not to damage the door sensor (top
right of oven).
Correctly lifting the cooker
Incorrectly lifting the cooker
Incorrectly moving the cooker
B
Fixing the backguard
It is mandatory to install the backguard.
Before installing the cooker, assemble the
backguard “C” .
The backguard “C” can be found packed
with the cooker.
1
2
3
4
C
A
Before assembling, remove any protective
film/adhesive tape.
Assemble the backguard “C” as shown
Screw in the two screws “A”, interposing
the spacers.
Screw in the central screw “B”.
Assembling
the backguard
11 US
CA
US
CA
Installation instructions
12
Levelling the range
The range is equipped with 4 LEVELLING FEET and may be
levelled by screwing or unscrewing the feet.
Follow the directions below.
Supplied with the range
in a separate kit
0”
0 mm
+ 5/16”
+ 8 mm
Supplied with the range
in a separate kit
+ 5/16”
+ 8 mm
+ 11/16”
+ 17.5 mm
Installation instructions
13 US
CA
Anti-tip stability device installation instructions
1
2
the anti-tip bracket has to be attached as shown on figure below (only rear left side), it has to be
fixed on the floor OR on the rear wall by no. 4 (four) suitable screws (not supplied). Alternatively
the anti-tip bracket can also be fixed on the floor AND on the rear wall by no. 8 (eight) suitable
screws (not supplied).
After fixing the anti-tip bracket, slide range into place. Be sure the rear left foot slides under the
anti-tip bracket attached.
Dotted line showing the position
of the range when installed
ANTI-TIP STABILITY
DEVICE FIXING
=
=
11” 11/16
(297 mm)
Anti-tip stability
device
Rear left
feet of range
YOU MUST USE STABILITY
ANTI TIP BRACKET TO
PREVENT UNIT FROM
TIPPING.
14
Installation instructions
Connecting the power supply cable
Important!
This cooker must be connected to the electricity supply only by an authorised person.
Your cooker is supplied with a certified 4 prong NEMA 14-50P power cord and should be
plugged directly into a properly grounded socket. Do not under any circumstances cut or
remove the forth (ground) prong from the power plug. Do not ground to a gas pipe.
Do not have a fuse in the neutral or ground circuit.
Do not use an extension cord.
Check with a qualified electrical installer if you are not sure if the range is properly grounded.
If codes permit, and a separate ground wire is used, it is recommended that a qualified electrical
technician determines the ground path and wire gauge are in accordance with local codes.
Be sure that the electrical connection and wire size are adequate and in conformance with:
ANSI/NFPA 70 latest addition and local codes and ordinances;
CSA standard C22.1, Canadian Electrical Code, Part 1 - latest edition and local codes and
ordinances.
When a 4-wire, two phase 120/240V or 120/208V 60Hz AC only electrical supply is available a 50
amp maximum circuit protection is required, fused on both sides of the line.
Replacing the power cord
Replacements should only be made by qualified electrical technicians.
If replacing the power cord, use only a suitable UL or CSA approved one. Tighten the power cord
using the power cord strain relief bracket supplied with the appliance. Allow enough slack to
easily attach the cord terminals to the terminal block.
Voltage and Power Consumption
AC 120/240 V 60 Hz 10950 W MAX
AC 120/208 V 60 Hz 10100 W MAX
INDUCTION POWER = 7400 W MAX
46 A MAX
48.84 A MAX
Standard NEMA 14-50R wall receptacle
Power supply cord with
NEMA 14-50P plug
Location of Nameplate
IU
RSI
IUTB
IHTO
OL
E61
CE
GE
TE
BE-INT
BE-EXT
TPL
DSPL
CF
OF
ER
DLM
SL/U
INDUCTION UNIT
ROTARY SELECTOR INTERFACE
INDUCTION UNIT TERMINAL BLOCK
INDUCTION HOB THERMAL OVERLOAD
OVEN LAMP
RELAY
CIRCULAR ELEMENT
BROIL ELEMENT
TOP ELEMENT
BOTTOM ELEMENT INT.
BOTTOM ELEMENT EXT.
THERMOSTAT PILOT LAMP
DOOR SAFETY PILOT LAMP
COOLING FAN
OVEN FAN
ENERGY REGULATOR
DOOR LOCK MOTOR
STATUS LOCK/UNLOCK
ELECTRIC DIAGRAM KEY
LINE PILOT LAMP
WARMING DRAWER ELEMENT
SAFETY THERMOSTAT
ELECTRONIC PROGRAMMER
DOOR STATUS, OPEN/CLOSED
OVEN DOOR LATCH
AIR SWITCH
CONNECTIONS ON PROGRAMMER
PN/PL
SUPPLY
K1
PROGRAM THERMOSTAT RELAY1
K2
COOLING/OVEN FAN RELAY2
K3
DOOR LOCK/UNLOCK RELAY3
PHV
FUNCTION STATE
X0
THERMOSTAT ENCODER
X1
FUNCTIONS ENCODER
P4
PROBE
P5B
WIRES P5B(1)+P5B(2)+P5B(3)
LPL
WD
ST
EL.P
SD
ODL
AS
Installation instructions
15
Wiring diagram
US
CA
First use
2
13
1
3
12
10
11
4
17 US
CA
5
6
7
8
9
Control panel
1
2
3
4
5
6
7
Control buttons
Clock display
Temperature dial
Function dial
Left front cooking zone dial
Left rear cooking zone dial
Right rear cooking zone dial
8
9
10
11
12
13
Right front cooking zone dial
Warming drawer control dial
Warming drawer indicator light
Function indicator light
Door lock indicator light
Temperature indicator light
18
US
CA
Setting the clock
Buttons
sets the timer
12:00 A
Indicates AM
sets the cooking time
sets the stop time for automatic cooking
Indicates PM
set the oven temperature /
select Celsius or Fahrenheit
decreases the time and temperature
increases the time and temperature
Clock display and control buttons
sets the Self Clean time
starts the oven/starts the Self Clean cycle
Illuminated symbols
If the display shows
0A
It means that...
For more information
flashing 12:00
The clock needs to be set.
See instructions below.
steadily lit
The oven is set for automatic
cooking.
flashing and
beeping
Automatic cooking has finished
steadily lit
The timer is set
See section ‘Using the electronic timer’
steadily lit
The oven is heating up
See section ‘Using your oven’
See section ‘Automatic cooking’
To set the clock
1
2
3
When the power to the appliance is turned on or restored after a power failure 12:00 will flash in
the display.
Press
and
together - the display will stop flashing. The clock is now set for 12:00.
Press
and
together again to change the time. The display will flash
Rotate the temperature dial or press
and
to set the time. After a few minutes the display
will be steadily lit, showing the time is set.
To change the time
1
2
Press
and
together. The display will flash.
Rotate the temperature dial or press
and
to set the time.
After a few seconds the display will remain steadily lit,
showing the time is set.
Note: when the indicator light is at the top the time is set for am
when the indicator light is at the bottom the time is set for pm.
Indicates AM
Indicates PM
12
Using your oven
Before using your new oven, please:
1
2
3
4
Read this user guide, taking special note of the ‘Safety and warnings’ section.
Remove all accessories and packaging. Peel the protective film off all surfaces and accessories.
Set the clock. The oven will not work until the clock has been set. See ‘To set the clock’.
Slide in the shelves you will need, making sure that:
they are between the two wires of a shelf position;
the stop notches point down;
the bigger guard rail is at the back.
5
Heat the oven on maximum for:
60 minutes in the
position
30 minutes in the
position
15 minutes in the
position
There will be a distinctive smell while you are conditioning your oven. This is normal, but
make sure your kitchen is well ventilated during the conditioning.
6
Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.
Stop notch
Bigger guard rail
Stop
notch
Correct position of shelves
19 US
CA
20
US
CA
Using your oven
Tmperature
indicator light
Function
indicator light
Function and temperature dials
FUNCTION
410 F
1
Select a function
Rotate the function dial to select a function
The function indicator light will come on.
The preset function temperature will flash
in the display. (Each cooking function has a
preset temperature).
430F
2a Adjust the temperature
Note: if you select
, the display will
show dEFand the oven will turn on. The
temperature cannot be adjusted when
using this function.
There are two ways to set the
temperature while the display is
flashing:
Rotate the temperature dial (clockwise
to increase and anticlockwise to
decrease the temperature);
OR
Use the
and
buttons to increase
or decrease the set temperature.
Press the
button. After a few
seconds, the display will stop flashing
and the oven will turn on and heat
up. The display will revert to show the
actual oven temperature.
The
indicator will show in the
display.
If the display is steadily lit and you wish to
change the temperature either:
Note: The temperature indicator light
will come on.
If you wish to use the oven at the preset
temperature Press the
button and the oven will
turn on and heat up. The display will revert
to show the actual oven temperature.
the
indicator will show in the display.
1
2
TEMPERATURE
Rotate the temperature dial; or
Press the button and use the
and
buttons to increase or decrease
temperature.
Using your oven
21 US
CA
190 F
3
When the oven is preheating and during
cooking
The
indicator will show in the display.
When the oven has reached the set
temperature the
indicator and the
temperature indicator light will go out.
Note: these indicators may turn on and off
during cooking as the oven maintains the
set temperature.
4a To check the set temperature
Press the
button.
The display will flash showing the set
temperature.
After a few seconds the display will return
to the actual oven temperature and the
display will be steadily lit.
4b To check the time of day
Press the
button.
After a few seconds the display will show
the oven temperature again.
FUNCTION
OFF
5
When you have finished cooking
Turn the function dial to OFF to turn the
oven off.
Note: if you change functions during cooking (eg from BAKE to BROIL) you will need to press
the
button again.
US
CA
22
Cooking functions
OVEN LAMP
Only the oven light comes on. It remains on in all the cooking functions.
DEFROST
this is not a cooking function
Only the oven fan comes on. The fan circulates air around the oven, speeding up the defrosting
process by approximately 30%. Note: this function is not for cooking food.
FAN FORCED
The circular heating element and the fan come on. The oven set on FAN FORCED can cook
several different foods together. Use FAN FORCED for multi-shelf cooking.
BAKE
The upper and lower heating elements come on. BAKE is the traditional method of cooking. It
is best to cook on only one shelf at a time in this function. Ideal for large cakes and dishes that
bake for several hours.
FAN BAKE
The upper and lower heating elements and the fan come on. Ideal for dishes like lasagne that
need to brown on top and also single trays of small cakes or biscuits that bake in less than an
hour.
BROIL
Broil is the most suitable function for ‘finishing off’ many meals, for example browning the top
of potato gratin and frittata. Use Broil to toast bread or to broil your favourite chicken, fish and
steak. Use with the oven door closed. For best results, use the topmost shelf position when you
want quick browning (eg toast).
FAN BROIL
Both the broil element and the fan come on. Use with the oven door closed. Ideal for roasting
tender cuts of meat and poultry. Use lower shelf positions for larger items eg a whole chicken.
Cooking functions
23 US
CA
SELF CLEAN
this is not a cooking function
The oven heats to a high temperature, reducing food residue to a fine ash that can be wiped out
with a damp cloth.
Important!
Do not leave food or cooking utensils etc. in the oven during self-cleaning.
Important!
Safe food handling: leave food in the oven for as short a time as possible before and after cooking or
defrosting. This is to avoid contamination by organisms which may cause food poisoning. Take particular
care during warmer weather.
Always use oven mitts when placing or removing items from the oven.
24
US
CA
Cooking guide
Changing the oven from Celsius to Fahrenheit
1
2
3
4
5
You can set your oven to display the temperature in Fahrenheit or Celsius.
Select a cooking function.
While the display is flashing, press
to reduce the oven to the minimum temperature
(120 oF / 50 oC).
Press
.
Press and hold the button until C or F flashes in the display
Press the button and to change between Celsius (C ) and Fahrenheit (F).
After a few moments the oven will turn off and the display will show the time of day.
Turn the function dial back to OFF.
Cooking Guide
The settings in the following chart are guidelines only. Follow the instructions in your recipe or
on packaging and be prepared to adjust the oven settings and baking times to achieve the best
possible results for you.
Shelf positions are counted from the oven floor up (1 is the lowest, 5 is the highest).
Arrange oven shelves before you turn the oven on, then preheat the oven to the desired
temperature.
Due to the width of the oven, a single shelf can usually accommodate double the standard
recipe.
Always preheat the oven before baking.
Do not place anything, including water or ice, on the oven floor.
Keep the door completely shut when broiling foods.
Do not open the door during the first 3/4 of baking time.
Always cook and broil with the oven door fully closed.
If the door stays open “door” flashes on the display and after some minutes an audible warning
sounds for about 30 seconds.
To silence the beep press any button.
Note: The heating elements work even with the door open and this signal just indicates that
energy is being wasted and the control panel/dials are being excessively heated.
Cooking guide
25 US
CA
SAVOURY
Shelves
Recommended
Function
Shelf
positions
Temp (°F)
Temp (°C)
Time (mins)
Roast Chicken
Single
Fan Forced
3
350-410
180-210
15-20
min/450g
Lasagne
Single
Fan Bake
3
345-360
175-180
45-50
Quiche
Single
Bake
1
360-390
180-200
30-40
Pizza
Single
Bake
3
430- 480
225-250
10-15
Casserole
Single
Fan Forced
3
340-370
170-190
55-70
Single
Bake
4
345-370
175-190
40-50
Single
Broil
4
Hi
6-8 min / side
Single
Broil
4
Hi
12-15
min / side
Food
Baked
Potatoes
Beef Steak
Beef Burgers
BAKING
Shelves
Recommended
Function
Shelf
positions
Temp (°F)
Temp (°C)
Time (mins)
single shelf
Bake
2
360-370
180-190
20-30
multi shelf
Fan Forced
1 and 3
320-340
160-170
30-40
single shelf
Bake
2
410-450
210-230
15-20
multi shelf
Fan Forced
1 and 3
410-450
210-230
15-20
two small pans (20
cm), on single shelf
Bake
2
340-360
170-180
30-45
one large pan
(26 cm)
Bake
2
345
175
30-40
Light fruit cake
two pans (21 cm)
on single shelf
Bake
2
310-330
155-165
90
Rich fruit cake
Single
Bake
2
270-300
130-150
3-6 hrs
Apple pie
Single
Bake
1
365
185
35-45
Quiche
Single
Bake
1
360-390
180-200
30-40
Meringues
Single
Bake
1
200-250
100-120
60
Bread rolls
Single
Bake
1
410-450
210-230
15-20
Muffins
2 x 12 muffin trays
on single shelf
Fan Forced or
Fan Bake
3
375-390
190-200
10-15
Pastry case
(baked ‘blind’)
one 21 cm flan tin
Bake
1
390
200
10 with beans,
then 10 without
Food
Cupcakes
Scones
Sponge
26
US
CA
Using the electronic timer
You can use the timer at any time, even when
the oven is not in use.
Important!
12:00 A
The timer does NOT turn the oven off.
To set the timer
1
2
3
4
Press the timer
button.
The time will show 0:00
Press
and
buttons or rotate the temperature dial to set the time you want (up to 3 hours in
one minute steps)
indicator will come on.
The timer
After a few seconds the time will start counting down, the display will show the time of
day (if the oven is off ) or temperature (if the oven is on) and will be steadily lit.
To check the remaining time
Press the timer
button.
The timer counts down in minutes (hr:min) until the last minute when it counts down in
seconds.
To cancel the timer
Press the timer
button.
button or rotate the temperature dial to
The remaining time will be displayed. Press the
scroll the time down to 0:00
After a few seconds the clock will show the time of day (if the oven is off ) or temperature
(if the oven is on).
When the time is up
indicator go out.
The timer will beep and the timer
Press any button to stop the beeping.
Automatic cooking
To set the oven for automatic cooking
Indicates AM
You can set the oven to automatically turn on later, Indicates PM
cook for a preset time (cooking time), then
automatically turn off at a preset stop time.
Alternatively you can simply set the time of day
you wish to the oven to turn off.
12:00 A
1
Set the oven
Check the clock shows the correct time (eg 12:07).
Select the function and set the temperature.
The Function indicator light will come on.
Press
. The oven will turn on.
2
Set the cooking time
Decide how long the food will take to cook, allowing
time for preheating if necessary (eg 40 minutes).
Press
.
or rotate the temperature dial to set the cooking time.
Use
and
display.
0A
3
27 US
CA
will show in the
Set the stop time
Decide when you want your food to be ready by (eg 13:30).
.
Press
and
or rotate the temperature dial to set the stop time.
Use
Note: The time indicator will tell you if you have set the time for am or pm.
You can turn the oven on manually and set it to turn off automatically by setting the stop time
(step 3 above).
0
When automatic cooking is set
If there is time before cooking starts, the oven will turn off and the pre-set temperature and A
will show in the clock display, indicating the oven is set for automatic cooking. Note: the cooling
fan and oven light may stay on.
The oven will automatically turn on at the required time (eg 12:50) and turn off at the set stop
time (eg 13:30).
To see the remaining cooking time, press
.
To see the set stop time, press
.
1
2
To cancel automatic cooking
Press and hold
and
together for 3 seconds.
Turn the function dial to OFF.
When the stop time is reached
The oven will turn off, the timer will beep.
0
1
2
The display will show End and the A will flash.
Press any button to stop the beeping.
Turn the function dial to OFF.
28
US
CA
Induction cooktop introduction
1
2
1
3
4
Cooktop layout
1
2
3
4
1850 W (3000 W *) 240V / 1665 W (2700W*) 208V zone
2300 W (3700 W *) 240V / 2070W ( 3330W*) 208V zone
1400 W (2200 W *) 240 V / 1260W (1980W*) 208V zone
Cooking zones display
* Maximum power output when set for PowerBoost (see section ‘Using your cooktop’s special
features’)
Important!
Disconnect the appliance from the mains if the ceramic glass is cracked and contact Customer Care.
Metallic objects such as knives, forks, spoons and lids should not be placed on the cooktop surface since
they can get hot.
Induction cooktop introduction
29 US
CA
Cooking zones display
The ceramic cooktop is fitted with induction cooking zones.
These circular zones are controlled by separate dials positioned
on the control panel below.
At the front, is the display for the cooking zones (one for each zone).
Each zone display is activated by it’s corresonding control dial and
displays:
Cooking zones diplay
= Cooking zone Off (not activated)
= Cooking zone On (activated but not operating).
If a zone is in zero setting, the display switches off automatically after
about 10 seconds.
= Very Gentle Heat setting
= Gentle Heat setting
-
= Power levels
= Auto Heat-reduce feature
= PowerBoost feature
= Hot Surface indicator
= Pan detection indicator
= Childlock
Note: each lit figure refers to the relevant cooking zone
US
CA
30
Choosing the right cookware
Important!
Only use cookware with a base suitable for induction cooking.
Look for the induction symbol on the packaging or the bottom of
the pan.
You can check whether your cookware is suitable by carrying out
a magnet test. Move a magnet towards the base of the pan. If it is
attracted, the pan is suitable for induction.
2
1
If you do not have a magnet:
1
Put some water in the pan you want to check.
2
Place a suitable pan on the cooking zone you wish to use. Make sure the bottom of the pan
and the surface of the cooking zone are clean and dry. Turn on the cooking zone.
3
If
does not flash in the display and the water is heating, the pan is suitable.
1
Note: If the pan detection symbol
does appear on the display, your pan is not suitable
and the cooktop will not operate. After 10 minutes without detecting any pan, the cooking
3
zone switches off automatically and can only be switched on after the control dial has
been returned to OFF.
Cookware made from the following materials is not suitable: pure stainless steel, aluminium or
copper without a magnetic base, glass, wood, porcelain, ceramic, earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is approximately
the same size as the cooking zone. Always centre your pan on the cooking zone.
Always lift pans off the cooktop– do not slide, or they may scratch the glass.
Choosing the right cookware
Important!
The cooking zones will not operate if the pan diameter is too small (
will appear on the
cooking zone display). To correctly use the cooking zones follow the indications given in the
following table.
Induction cooking zone
Minimum pan diameter
recommended
Front right
120 mm
Rear right
145 mm
Rear left
145 mm
Front left
145 mm
Note: some types of pans can cause noise when used on an induction cooking zone.
This noise does not mean any failure on the appliance and does not influence the cooking
operation.
Important!
Do not use the cooktop during an oven Self clean cycle.
31 US
CA
US
CA
32
Using your induction cooktop
Control dials
Each cooking zone is activated by a separate control dial positioned on the control panel. The
functions are arranged on the actual dial itself.
If a cooking zone is not turned off (OFF position) the electronic system automatically switches
it off after a pre-set time ranging from 90 minutes to 520 minutes, depending on the power
setting.
1
1
9
2
8
2
7
3
Power level
4
5
6
Control dial
Push the dial in and turn it clockwise to set the temperature between Very Gentle heat
and
9 (maximum).
The power level can be modified at any time by turning the dial clockwise or counter-clockwise
to a different setting.
The cooking zone display shows the selected level.
Hot Surface Indicator
When the temperature of a cooking zone is still hot, the relevant Hot Surface indicator
lights
up on the display to alert you of the hot surface. Avoid touching the cooktop surface over the
cooking area. Please pay special attention to children. When the
is lit on the display, it is
still possible to start cooking again; just turn the control dial to the required power level. The
indicator will disappear when the surface has cooled down to a safe temperature.
Childlock
You may lock all of the cooktop. Ensure the cooking zones are turned OFF.
Push and turn the left cooking zones dials to the left (‘A” setting) and hold the dials down
until the
lights up on the cooking zone displays (on the left cooking zones displays,
lights up after
); then release the dials after the beep.
After a few seconds the
will go out, but the cooktop remains locked.
To deactivate the childlock repeat the same procedure until the
goes out (and after the
beep).
If you try to turn a cooking zone on while locked the
will show in the display. The
will
remain lit until the dial is turned back to OFF. If you try to set the Auto Heat-reduce feature (‘A”
setting) on a cooking zone while locked, nothing will be shown in the display and the feature
will not be set.
Using your cooktop’s special features
33 US
CA
Using the Auto Heat-reduce feature
This feature is available on all the cooking zones
Push and turn the control dial counter-clockwise to the ‘A’ setting until the
symbol lights up
on the corresponding cooking zone display then release the dial after the beep. Within 5 seconds
turn the dial to the desired power level (between 1 and 8); once a setting has been selected,
after a few seconds
and the set power level will be alternating in the display.
This feature allows the cooking zone to operate at the maximum power (100%) for a time
proportional to the selected power level; after this time the cooking zone will operate at the
selected level.
While this feature is operating it is possible, at any time, to increase the selected power level up
to level 8 (at level 9 the function will be disabled). It is not possible to decrease the power.
The Auto Heat-reduce feature can be disabled by turning the dial anti-clockwise to a lower
power level, turning the dial to the OFF position or by selecting level 9 or the PowerBoost
feature.
Note: If removing the pan from the cooking zone before the programme has been completed,
the Auto Heat-reduce feature will be completed with the remaining time if the pan is put
back on the cooking zone within 30 seconds, while the
symbol is lit in the display. After 30
seconds the zone is automatically turned off.
Using the PowerBoost feature
Turn the control dial clockwise to set the maximum power level (9), then turn clockwise again to
the
setting until ‘P’ appears on the display, then release the dial after the beep; the control
dial returns to the maximum setting (9) automatically and the
symbol lights up on the
corresponding cooking zone display. The PowerBoost feature is now on.
This feature allows the cooking zone to operate at the PowerBoost maximum power (above the
rated power) for a maximum of 10 minutes; it could be used, for example, to rapidly heat up a
large amount of water. After 10 minutes
will flash for a few seconds. The cooking zone will
then decrease to power level 9.
The PowerBoost feature can be disabled by turning the dial anti-clockwise to a lower power
level, turning the dial to the OFF position or by turning the dial again to the
setting; in this
case the cooking zone operates at the power level 9.
Note: if a cooking zone is still hot, it is not possible to use the PowerBoost feature and
will
flash if you try to activate. The cooking zone is automatically set to the maximum power level (9).
The PowerBoost feature is always limited to a maximum of 10 minutes. You can activate the
PowerBoost feature again after 10 minutes.
Important!
The PowerBoost feature is not suitable for use with non water based cooking.
Do not use this function for heating oil (e.g. deep fat frying). The power density may be too high
and it could damage the cookware.
US
CA
34
Using your cooktop’s special features
Maximum usable power for the cooking zones
The right and left cooking zones are controlled by two
separate power boards and the maximum total power per
each power board is 3700 W.
Should the cooking zones of one power board require more
than 3700 W, the last selected power level has priority and the
power of the other cooking zone is automatically reduced to
the remaining power available.
If this occurs, the cooking zone will display a flashing figure
for about 3 seconds before automatically displaying the new
power level.
Controlled by
1st power board
Controlled by
2nd power board
This means for example that:
When setting PowerBoost for the second zone, the setting for the other zone could be reduced
to the remaining power available.
When setting PowerBoost for a zone and then another setting on the second zone, if the total
power exceed 3700 W the PowerBoost feature is automatically turned off and the power reduced
to the maximum power available.
Very Gentle (melting function) and Gentle Heat (warming function)
The Very Gentle heat setting is ideal for melting while the Gentle heat setting is ideal for keeping
cooked food warm and the gentle warming of delicate foods for up to 2 hours.
Push and turn the dial to the
or
setting. The display will show
or
.
Thermal protection
The induction cooktop is fitted with safety devices to protect the electronic system and to
protect each cooking zone from overheating.
In case of overheating, one of the following automatic functions could be started by the
electronic system:
PowerBoost feature automatically turned off and power reduced;
one or more cooking zone switched off;
cooling fan motor of the induction unit switched on.
Cooking guidelines
35 US
CA
Heat settings
The settings below are guidelines only. The exact setting will depend on several factors,
including your cookware and the amount you are cooking. Experiment with the cooktop to find
the settings that best suit you. In general, the lower heat settings offer a more gradual control,
whereas the higher heat settings have a more pronounced step change in power.
100
Percentage of power %
80
60
40
20
0
u
1
2
3
4
5
6
7
Heat setting
Heat setting
8
9
P
(A)
Suitability
1-2
delicate warming for small amounts of food
melting chocolate, butter, and foods that burn quickly
3-4
gentle simmering
cooking rice
5-6
rapid simmering
pancakes
7-8
sautéing
cooking pasta
9
stir-frying
searing
P
boiling water
Note: the settings and suitability shown are subject to variability due do differences in cookware construction.
36
US
CA
Using the warming drawer
Important!
The warming drawer is for keeping cooked food hot only.
Do not use it to warm plates.
Do not use as a storage drawer.
Do not use it as a space heater.
Do not use the warming drawer during a self clean cycle.
Note: The drawer will automatically turn off when the
self clean cycle is started. It may resume functioning when
the function dial is switched ‘OFF’ at the end of the
self clean cycle.
The warming drawer is fitted with a heating element in the top.
You may set the heat from LO (86 oF / 30 oC) to HI (203 oF/95 oC).
First Use
We recommend that you condition your warming drawer
before using it for the first time.
1
2
3
To condition your warming drawer:
Ensure the warming drawer is empty.
Close the drawer fully.
Push and turn on Warming drawer dial to ‘HI’
The warmer drawer indicator light will come on.
After 2 hours, turn the warming drawer OFF.
Allow the warming drawer to cool completely.
Wipe out with a damp cloth and mild detergent, and dry thoroughly.
There will be a distinctive smell while you condition your warming drawer. This is normal but
ensure your kitchen is well ventilated.
Using the Warming drawer
Push and turn the control dial to select a temperature setting between LO (min) and HI (max).
Allow time for the drawer to be preheated.
Preheat with rack in place (see ‘Using the reversible rack’).
Preheat the empty serving dish while preheating the drawer.
Add cooked, hot food in a heat-safe cooking or serving dish.
Food may be kept hot in its cooking container or transferred to a heat-safe serving dish.
Aluminium foil may be used to cover food.
Note: Plastic containers or plastic wrap may melt if they come in contact with the hot drawer.
Using the warming drawer
Reversible rack
Your warming drawer comes with a reversible rack. Position the rack as shown.
Reheating food
Always re-heat food until piping hot before transferring to the warming drawer.
Food kept at temperatures of less than 140 oF / 60 oC for more than two hours are at risk of
becoming contaminated by harmful bacteria.
Important!
Never reheat a food more than once.
37 US
CA
US
CA
38
Care and cleaning
Important!
Before you start cleaning your cooker, please:
Read these cleaning instructions and the ‘Safety and warnings’ section at the start of this user
guide.
Turn the cooker off at the wall.
Make sure the cooker is a safe temperature to touch.
Do not use a steam cleaner.
Do not store flammable substances in the oven or warming drawer.
General advice
Wipe down the cooktop and wipe out the oven after every use.
Wipe up spills. Avoid leaving alkaline or acidic substances (such as lemon juice or vinegar) on
the surfaces.
Do not use cleaning products with a chlorine or acidic base (ie citrus-based cleaners).
Cleaning the outside of the cooker
Important!
Do not use abrasive cleaners, cloths or pads on the outside surfaces.
Immediately wipe off any caustic cleaners if they are spilled onto the oven door handle.
Wipe the outside surfaces often, using warm water and a mild household detergent. The
stainless steel may also be cleaned with a suitable cleaner and polish.
Note: if you choose to use a commercial stainless steel cleaner, please read the label to make
sure it does not contain chlorine compounds as these are corrosive and may damage the
appearance of your cooker.
Care and cleaning
39 US
CA
Caring for your cooktop
Important!
Some heavy-duty and nylon scourers can scratch the ceramic glass of your cooktop. Always read
the label to check if your scourer is suitable for cleaning ceramic glass cooktops.
Use ceramic glass cleaner on the cooktop while it is warm to touch. Rinse and wipe dry with a
clean cloth or paper towel. The cooktop may become stained if cleaning residue remains.
Remove any food, spillovers or grease from the cooktop while it is still warm using a razor blade
scraper suitable for ceramic glass surfaces. Do not use knives or any other sharp object for
cleaning. Take extra care to avoid damaging the seal at the edges of the ceramic glass surface.
Do not use cleaning products with a chlorine or acidic base.
Metallic stains
Copper-based or aluminium cookware may cause metallic staining. These stains show as a
metallic sheen on the cooktop. If the cooktop is not cleaned after every use and the stains
are allowed to burn onto the surface, they may react with the glass and will no longer be
removable. To help prevent such damage, clean the cooktop after every use and apply a
glass cooktop conditioner.
Cleaning melts and spillovers
Anything that melts onto the ceramic glass surface or food spills with a high sugar content may
cause pitting of the ceramic glass surface if they are left there to cool. Examples include:
plastic wrap
melted aluminum foil
sugar, sugary syrups, jams and jellies
vegetables and vegetable water with a high sugar content eg peas, sweet corn, beetroot.
Remove these spills immediately with a special razor blade cooktop scraper, taking care not to
scratch the glass. Follow the steps below:
1
2
3
Turn the element off and carefully scrape the spill to a cool area of the cooktop surface.
Clean the spill up with a cloth or paper towel.
As soon as the cooktop is cool enough to safely touch, clean with cooktop cleaner.
Cleaning the stainless steel surround strip
To remove fingerprints and other marks, wipe with a clean damp cloth and dry with a lintfree
cloth.
40
US
CA
Care and cleaning
Cleaning the inside of your oven
Note: if using the Self Clean function remove all shelves and side racks first. See ‘Using the Self
Clean function’.
Do not use abrasive cleaners, cloths or pads to clean the enamel.
Removing the side racks
1
2
Using a small coin or a flat-head screwdriver, loosen and remove the front fixing screw only.
Slide the side rack clear of the rear lock stud and remove.
Refitting the side racks
3
Slide the side rack gently so it engages with the rear lock stud. Make sure that they are the right
way up, as in the illustrations, and then insert and tighten the front fixing screw.
Removing the side racks
Care and cleaning
41 US
CA
Cleaning the enamel cavity
Clean the enamel on the inside of the oven when
it has cooled down, using household detergents.
Dry with a soft cloth.
Stop notch
Bigger guard rail
Cleaning the broiler pan and rack and
shelves
Clean these in hot, soapy water. After cleaning
slide in the shelves and tray, making sure that:
they are between the two wires of a
shelf position;
the stop notches point down;
the bigger guard rail of the shelf is at the
back.
Stop
notch
Oven shelves
Fitting and removing the sliding shelf supports
When fitting the sliding shelf supports, make sure that you fit:
the side racks first
the slides to the top wire of a shelf position
both sides of each pair of slides
both slides on the same level.
Important!
Remove the side racks first to make removing the sliding shelf supports easier.
1
2
1
US
CA
42
Care and cleaning
Using the Self Clean function
During the pyrolytic Self Clean cycle the extremely high temperature burns off and breaks
down grime and grease deposits. All that is left is a small amount of grey ash that you can easily
remove.
You can set the Self Clean cycle time between one and a half and three hours. The heavier the
soiling, the longer the cleaning time required.
Important!
You must clean the inside glass door panel BEFORE starting a Self Clean cycle. Failure to do this
may result in permanent staining or marking of the door glass.
Do not use oven cleaners, any degreasing cleaners, or oven liners.
Make sure you remove the side racks, oven shelves and trays and all other bakeware and utensils
from the oven before starting a Self Clean cycle. If left in the oven, they will become permanently
discoloured or damaged; items made from combustible materials (eg wood, fabric, plastic) may
even catch fire.
Do not operate the warming drawer during the self clean cycle.
The warming drawer will become warm during the Self Clean cycle. Do not store flammable items
in the warming drawer. If possible, avoid opening the drawer during the cycle, or use oven mitts
to remove items from the drawer.
Do not use your oven to clean miscellaneous parts.
Make sure the room is well ventilated.
Before starting a Self Clean cycle, make sure you move any pet birds to another, closed and wellventilated room. Some pet birds are extremely sensitive to the fumes given off during a Self Clean
cycle, and may die if left in the same room as the oven during such a cycle.
During a Self Clean cycle, the oven reaches higher temperatures than it does for cooking. Under
such conditions, the surfaces may get hotter than usual and children should be kept away.
The oven door will be locked during the Self Clean cycle. After the Self Clean cycle has finished,
the door will remain locked until the oven has cooled to a safe temperature. This may take up to
30 minutes.
If there are cracks or flaws on any of the oven door glass panes, if the oven seal is damaged or
worn, or if the door does not close properly, do not start a Self Clean cycle. Call your Authorised
Repairer or Customer Care.
Caution: Do not leave food or cooking utensils etc. in the oven during self-cleaning.
Care and cleaning
43 US
CA
To start a Self Clean cycle
1a Remove oven shelves, side racks and all other accessories, bakeware, and utensils.
1b Wipe up any spills. Failure to do so may discolour the oven surfaces.
1c Check the inner glass pane of the oven door. If it has soiling on it (eg stains from greasy splatter),
you will need to clean it manually before starting a Self Clean cycle.
Important!
If soiling is left on the glass, it will become burnt on during the Self Clean cycle, making it very difficult to
remove.
2
Close the oven door firmly.
44
US
CA
3
Care and cleaning
Select the Self Clean Function
The display will show
The P will flash.
P1:30 A
4
Adjust the cycle time (optional)
You may set the time between 1-1/2 hours (P1:30 and 3 hours (P3:00). For heavy soiling use
a longer time.
button - the P will go out.
Press the
and
buttons or rotate the temperature dial to change the time.
Use the
button
After a few seconds the P will start to flash again. Alternatively, press the
to confirm and the P will flash.
5
Start the cycle
button. The P will stop flashing.
Press the
indicator will show in the display.
The oven will come on and the
After a few seconds the door will lock and the door lock indicator light will come on.
The display will start to count down.
Note: If the door is not shut completely, after a few minutes the oven will switch off, the display
will show ‘door’ and the oven will beep. See ‘Troubleshooting’.
6
At the end of the Self Clean cycle
The oven will turn off.
The display will show P:00 and a flashing A
7
Turn the function dial to OFF.
The door will remain locked.
The door lock indicator will remain on.
The display will show ‘hot’.
When the oven has cooled to a safe temperature, the door lock indicator will go out and the
door will unlock. The display will show the time of day. This may take 30 minutes.
Note: The oven will still be very warm. To avoid burns, wait for the oven to cool completely
before wiping out the ash and replacing side racks and shelves.
To cancel a Self Clean cycle
Turn the function dial to OFF.
Note: The oven door will remain locked until the oven has cooled to a safe temperature. The door
lock indicator light will remain on, and the display will show ‘hot’.
We do not recommend that you start a new Self clean cycle before the oven has cooled
completely.
Care and cleaning
45 US
CA
Replacing the oven light bulb
Use only a bulb suitable for high temperature (300 oC/ 572 oF) having the following
specifications:
120V, 60Hz, E14 and the same power as the one you remove (this will be stamped on the bulb).
1
2
3
4
5
Turn off the power to the range.
Wait for the oven to cool completely.
Remove the cover (A).
Unscrew and replace bulb (B).
Replace cover.
NOTE: Oven bulb replacement is not covered by your warranty.
A
B
B
A
46
US
CA
Care and cleaning
Important!
Do not remove drawer while hot.
Do not remove drawer during operation.
Be sure drawer is empty before removing.
1
2
3
Removing the warming drawer
Open the drawer completely.
Push and hold the lever on the left guide down, and the lever on the right guide up.
Remove the drawer while holding the levers in position.
2
3
2
1
2
Refitting the warming drawer
Insert the drawer guides into the slide.
Gently close the drawer completely. The safety catches will automatically hook into place.
Care and cleaning
47 US
CA
Removing the oven door
1
The oven door can easily be removed as follows:
Open the door to its fullest extent.
Open the lever “A” completely on the left and right hinges.
Hold the door as shown.
Gently close the door until left and right hinge levers “A”
are hooked to part “B” of the door
Withdraw the hinge hooks from their location following
arrow “C” .
Rest the door on a soft surface.
Refitting the oven door
2
A
B
Hold the door firmly.
Insert the hinge tongues into the slots, making sure that
the groove drops into place as shown.
Open the door to its full extent.
Fully close the levers “A” on the left and right hinges, as
shown.
Close the door and check that it is properly in place.
3
6
4
A
C
5
7
US
CA
48
Cooktop fault codes
Error codes on the cooking zones display
Error code
Example
What to do
1
Er20, Er31
or Er47
or
display
not operative
E2
2
3
4
1
2
1
2
E6 or
E7 or E9
or E5
3
4
Switch off the cooker and disconnect it from the
mains.
Wait for about 1 minute, then reconnect the
cooker and turn on the cooking zones.
Wait for about 1 minute and if the error message
does not appear again the cooking zones can be
used.
If the problem continues make a note of the
error code, switch off the appliance and contact
your Authorised Service Centre.
‘E’ and ‘2’ alternating for one or more cooking
zones.
This indicates an overheating of the cooking
zone/s.
Switch off the cooking zone/s and leave to cool.
If the problem continues do not use the
induction cooktop (only use the oven) and
contact your Authorised Service Centre.
Switch off the cooker and disconnect it from the
mains.
Wait about 1 minute, then reconnect the cooker
and turn on the cooking zones.
Wait for about 1 minute and if the error message
does not appear again, the cooking zone can be
used.
If the problem continues, make a note of the
error code, switch off the appliance and contact
your Authorised Service Centre.
Cooktop fault codes
49 US
CA
Error codes on the cooking zones display
Error code
Example
What to do
1
U400
2
1
Symbol
as per
side
figure
2
3
4
5
This indicates an over-voltage on power supply.
Switch off the cooker and disconnect it from the
mains.
Check the correct power voltage is available in
the domestic electrical system as indicated in
the appliance rating label.
This indicates an incorrect operation of one or
more cooking zone control dial.
Turn the cooking zone control dials to the
OFF position, then switch off the cooker and
disconnect it from the mains.
Wait for about 1 minute, then reconnect the
cooker and turn on the cooking zones.
Wait for about 1 minute and if the error message
does not appear again the cooking zones can be
used.
If the error message does not disappear repeat
step from 1 to 3.
If the problem continues do not use the
induction cooktop (only use the oven) and
contact your Authorised Service Centre.
If any other error codes are displayed, switch off your cooker and call Customer Care or your
Authorised Service Center .
US
CA
50
Troubleshooting
Troubleshooting chart
Problem
Possible causes
What to do
The cooktop cannot be
turned on.
No power.
Make sure the cooker is
connected to the power supply
and that it is switched on at the
wall. Check whether there is
a power outage in your home
or area. If you’ve checked
everything and the problem
persists, call your Authorised
Service Centre or Customer
Care.
The glass is being
scratched.
Rough-edged cookware.
Use cookware with flat and
smooth bases. See ‘Choosing
the right cookware’.
Unsuitable, abrasive scourer or
cleaning products being used.
See ‘Care and cleaning’.
Some pans make
crackling or clicking
noises.
This may be caused by the
construction of your cookware
(layers of different metals
vibrating differently).
This is normal for induction
cookware and does not indicate
a fault.
The cooktop makes a low
humming noise when
used on a high heat
setting (especially
PowerBoost).
This is caused by the technology
of induction cooking.
This is normal, but the
noise should quieten down
or disappear completely
when you decrease the
heat setting.
Pans do not become hot
and
appears in the
display.
The cooktop cannot detect the
pan because it is not suitable for
induction cooking.
Use cookware suitable for
induction cooking. See
section ‘Choosing the right
cookware’.
The cooktop cannot detect the
pan because it is too small for
the cooking zone or not
properly centred on it.
Centre the pan and make
sure that its base matches
the size of the cooking
zone.
Troubleshooting
51 US
CA
Troubleshooting chart
Problem
Possible causes
The display flashes door The function dial has been
turned to Self clean when the
door is still open.
(An alarm may also
sound)
The door has been opened after
Self clean has been selected but
before the oven has been
started.
What to do
Close the door and restart the
Self clean sequence.
Close the door and restart the
Self clean sequence.
The door is open during
cooking.
Close the door. The oven is still
operating normally.
The display shows Fdor
The door lock is
malfunctioning.
Turn the function dial to OFF.
Wait for the oven to cool down
completely and disconnect the
cooker from the mains power
supply.
Wait a few minutes then
reconnect the mains.
If the display still shows Fdor
disconnect the cooker again
and call your Authorised Service
agent of Customer Care. Do not
use the cooker.
The display shows
F0E0 A
The Self clean cycle has been
stopped and then immediately
re-started.
Note: we advise against
stopping a Self clean cycle and
then immediately starting it
again. Always wait for the oven
to cool completely first.
Turn the function dial to OFF.
Wait for at least 30 minutes and
then start the Self clean cycle
again.
If the error re-occurs call your
Authorised Service Agent or
Customer Care.
US
CA
52
Troubleshooting
Troubleshooting chart
Problem
Possible causes
What to do
The display shows F000
or F001
The oven temperature sensor is
malfunctioning. The cooling fan
will remains on and if the Self
cleaning cycle is in process the
door will remain locked.
Turn the function dial to OFF.
Wait for the oven to cool down
completely and disconnect the
cooker from the mains power
supply.
Wait a few minutes then
reconnect to the mains power
supply.
If the display still shows the
error code, disconnect the
cooker from the power supply
and call your Authorised
Service Agent or Customer
Care.
The display shows Fpot, The oven is malfunctioning.
Fdor, FAdc or FrEL
The display is blank.
Turn the function dial to OFF.
Wait for the oven to cool
down completely and
disconnect the cooker from
the mains power supply.
Wait a few minutes then
reconnect to the mains power
supply.
If the display still shows the
error code, disconnect the
cooker and call your
Authorised Service Agent or
Customer Care – the cooker
must not be used.
Turn the function dial to OFF. Wait for the oven to cool down
completely and disconnect the cooker from the mains power
supply.
Wait a few minutes then reconnect to the mains power supply.
If the display is still blank disconnect the cooker and call your
Authorised Service Agent or Customer Care – the cooker must
not be used.
Warranty and service
53 US
CA
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions and your user guide
and check that:
1
2
your product is correctly installed
you are familiar with its normal operation.
If after checking these points you still need assistance or parts, please refer to the Service &
Warranty book for warranty details and your nearest Authorized Service Center, or contact us
through our local website listed on the back cover.
Product details
Fisher & Paykel Ltd
Model
Serial no.
Date of purchase
Purchaser
Dealer
Suburb
Town
Country
www.fisherpaykel.com
Copyright © Fisher & Paykel 2017. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
US CA
F&P PN - 590619 D F&P ITALY PN - 1105340 - ß1
03.2017
Download PDF
Similar pages