Lowering technology
Elabo lowering technology
satisfies a very wide range
of requirements.
For IT applications there is
a special version with
lowerable TFT monitors.
In-room power distributors
house the central fuse
protection for entire
classrooms and also
accommodate the control
for the lowering mechanism.
Tables equipped with
electric motor-driven
fold-away mechanisms
(3 HU system) are very
compactly dimensioned.
The vertically raisable and
lowerable superstructures
are available in single- or
double-stage versions and
are also fitted with 3 HU as
well as 6 HU grids.
A handy wireless remote
control is available which
the instructor can conveniently carry with him.
Elabo Training Systems
59
Lowering technology
Clear overview. Safety.
Maximum use of space
With Elabo‘s lowering technology superstructures
can be brought into view or made to disappear again.
A theory table can be quickly converted into an
experiment table for practical instruction. And directly
following the practical training for electrical trades,
completely different training topics can be dealt
with in the same room. This considerably increases
the versatility and usability of the classrooms.
Equipment immediately available
The superstructures move up and down in
less than 20 seconds. At the start of the
practical instruction session all the instruments are very quickly available without a
lot of time having to be spent collecting
them together, connecting them up and
adjusting them. Shut-down is just as
compact. This guarantees the maximum
net amount of study time.
Superstructure variants
The basic variant of the lowerable superstructures is the superstructure (System
6 HU and 3 HU) carrying a single-row of
equipment and devices. A two-level variant
is also available which also contains a shelf
compartment in addition to the area
containing the electronic devices. The shelf
area can be used as a place for additional
measuring devices, or it can also be used
as a storage area.
Superstructures that can be
raised and lowered in one or
two stages are available from
Elabo. They can be raised so
precisely that the upper level is
fully accessible while the second
level – containing for example
the electrical devices – remains
hidden.
As an alternative to the vertically raisable
and lowerable superstructure, Elabo also
supplies a variant that can be folded up and
down. In this case, an electric motor drives
a superstructure that is attached to hinges
and pivots the structure upwards out of the
table. In this version as well, the fold-away
technology ensures ergonomically optimal
operation of the installed electrical devices.
For IT instruction Elabo has developed a
lowerable superstructure which – instead
of the inserts grid or shelves –­ incorporates
Elabo Training Systems
Satisfying individual customer wishes
There is hardly any limit to the spectrum of
special versions that can be offered on
request. In many cases designs are
needed with special dimensions. But there
are also concepts that can only be manufactured in response to individual orders.
For example, lowerable superstructures
with rear and side walls made of plexiglas
are requested in those cases where,
despite having large superstructures, the
classroom should be transparent and the
view of the student’s desk should not be
completely blocked.
3 HU fold-away technology
Special version for IT
60
mountings for TFT monitors. They meet the
VESA standard. The body of the lowering
assembly is an independent element that
be attached to already existing tables.
Lowerable superstructures are
supplied with a central control
system housed in a cabinet with
the classroom power supply
system. A compact wireless
remote control which the
instructor carries with him is
optionally available.
Elabo lowering technology comes
in two forms that help tailor the
equipping of the classroom to
exactly meet individual requirements. In the first variant the
complete superstructure moves
vertically up and down. In the
second variant, the superstructure
pivots up and down around an axis
of rotation. This fold-away method
is ideal for raising/lowering very
compact superstructures.
Elabo can provide individually
tailored designs at any time, such
as special dimensions or also
special concepts, for example a
lowerable superstructure made
of plexiglas. The latter is a frequently requested item because
of its transparency.
The IT version is one of the
special designs of lowerable
superstructures available from
Elabo: TFT monitors disappear
in space-saving fashion into the
body of the lowering assembly.
In addition there is room for a
keyboard and mouse.
Elabo Training Systems
61
Lowering technology
Well thought-out solutions and
very reliable technology
Lowering technology offers users an enormous amount
of flexibility. However, it does require that all the
components are exactly matched to each other. Elabo is
a pioneer in this field. The mechanical guidance and the
drive technology mesh so perfectly with each other that
practically no wear is caused. It has been shown that
the lowerable superstructures are still working without
problems even after 15 years and more of operation.
Compatible with the 19” system
Lowerable superstructures that meet the
international 19” standard can be obtained
from Elabo. Using the assembly carriers
provided, devices from the 3 HU and
the 6 HU system can also be integrated
into the 19” technology. Various other
manufacturers also offer devices for the
19” concept and they can likewise be integrated into the lowerable superstructures
from Elabo
62
The lowerable superstructures,
together with their technology,
are housed in their own separate
assembly. In order to ensure
that the body of the lowering
assembly and the table together
have the usual standard proportions on which spatial planning
is based, Elabo offers add-on
tables in special dimensions.
Elabo Training Systems
The lowering technology is
based on a very high safety
standard. The automatic sensorcontrolled shut-off mechanism
ensures that no injuries are
caused by moving parts.
Connection to the table system
Classroom power supply
The body of the lowering assembly is
connected directly to the system table
(InForm or EcoTec) and is screwed firmly to
it at defined interfaces. Both elements are
joined to one another without any steps or
gaps and together they form a very stable,
generously dimensioned working area.
The classroom power supply cabinet is part
of the lowering technology. The lowering
mechanism on each individual table, or on
all tables simultaneously, can be controlled
via an operating panel fitted with up/stop/
down buttons.
Drive technology
Depending on the load factor, one or two
electric motors, which are linked via a
connecting rod, provide the drive for the
lowering system. The drive is controlled by
an electronic system developed by Elabo.
Prevention of injury
For the protection of the operator, Elabo
equips all its vertical lowering systems
with a shut-off strip with positively guided
safety contacts. Once the strip is triggered,
the superstructure stops moving downwards within fractions of a second and
moves upwards again. This reliably
prevents objects (or in the worst case, a
hand) from becoming caught. The process
is electronically controlled.
A key-operated switch in the classroom
power supply cabinet turns on the power
supply for the entire room. Here all the
tables are centrally fuse-protected (one
fuse per table, single or three-phase,
depending on the power level). This is also
where the EMERGENCY OFF switch is
located. When the EMERGENCY OFF
switch is operated a space contactor
automatically shuts off the power to the
entire room.
The classroom power supply
cabinet also contains the
control system for the lowering
technology.
Colours and materials
The superstructures and the body of the
containers are made of fine particle
boards, coated on both sides with
melamine resin. The standard paint finish
in which they are supplied is light grey
RAL 7035. This is a colour that looks
professional and meets practical requirements.
Elabo Training Systems
63
Lowering technology
Expandable Modules
This may also interest you...
Elabo lowering technology considerably
increases the usability of your classrooms.
You can create your own totally application-optimized solution by making use of
further modular components.
64
Inserts and electronic
devices from Elabo, such
as measuring devices and
power supply devices, are
ideally suited for teaching
purposes, retain a high
degree of accuracy and have
a long service life. They are
specifically matched to the
lowerable and also the fixed
superstructures.
> More on page 75
Virtual Equipment from Elabo
provides the network technology and switches that are
integrated into the lowerable
superstructures. Using Module
4Room of the Elabo software
EHP EduLab you can not only
control individual workplaces,
as well as all workplaces
together, but you can also individually define and programme
different groups.
> More on page 109
Storage containers ensure
neatness and good order in
the classroom. Floor units, in
particular the special PC floor
units from Elabo, are very
often requested for use in
conjunction with the lowerable
systems. They are lockable
and equipped with an efficient
ventilation system.
> More on page 155
Superstructures in a wide
range of variants are often
required especially for the
instructor tables. Elabo offers
them in the 3 HU and 6
HU systems, which can be
combined with each other
> More on page 45
The wide range of modular
table systems from Elabo
perfectly rounds off the
equipment needed in the
classrooms.
> More on page 27
Chairs of high ergonomic
quality promote concentration
and help ensure that students
remain attentive for long
periods of time.
> More on page 181
Elabo Training Systems
Elabo Training Systems
65
Lowering technology
3 HU Lowering technology System
Technical specifications
Lowerable table superstructures
1-tier
Lowerable table superstructures
2-tier
66
Elabo Training Systems
WxDxH
Article Number
For accepting 360 HP
2000 432 780
A4-1A
For accepting 318 HP
1800 432 780
A4-1B
For accepting 282 HP
1600 432 780
A4-1C
For accepting 258 HP
1500 432 780
A4-1D
For accepting 198 HP
1200 432 780
A4-1E
For accepting 360 HP
2000 432 780
A4-2A
For accepting 318 HP
1800 432 780
A4-2B
For accepting 282 HP
1600 432 780
A4-2C
For accepting 258 HP
1500 432 780
A4-2D
For accepting 198 HP
1200 432 780
A4-2E
Lowering mechanism, with superstructure
that is vertically extended by electric motor
drive, and with a safety shut-off strip.
For accepting 3 HU Euro inserts.
Prepared for addition of an EcoTecSP or
InForm system table.
Height of superstructure body in raised
state: 1000 mm
Lowering mechanism, with superstructure
that is vertically extended by electric motor
drive, and with a safety shut-off strip.
1st tier: For accepting 3 HU Euro inserts.
2nd tier: Shelf element with central wall
and shelf panels.
Prepared for addition of an EcoTecSP or
InForm system table.
Height of superstructure body in raised
state:
1st tier: 1000 mm
2nd tier: 1340 mm
Lowering technology System 6 HU
Add-on tables
Technical specifications
Lowerable table superstructures
1-tier
Lowerable table superstructures
2-tier
Add-on tables with
lowering technology
for 3 HU and 6 HU System
WxDxH
Article Number
For accepting 15 WU
2000 432 780
A5-1A
For accepting 13 WU
1800 432 780
A5-1B
For accepting 12 WU
1600 432 780
A5-1C
For accepting 11 WU
1500 432 780
A5-1D
For accepting 8 WU
1200 432 780
A5-1E
For accepting 15 WU
2000 432 780
A5-2A
For accepting 13 WU
1800 432 780
A5-2B
For accepting 12 WU
1600 432 780
A5-2C
For accepting 11 WU
1500 432 780
A5-2D
For accepting 8 WU
1200 432 780
A5-2E
EcoTecSP add-on table prepared for
connecting to lowering mechanism types of
the A4... and A5... series. Table frame with
welded steel tube apron frame and screwattached steel tube table legs 50 x 50 mm.
Table top 30 mm thick, with replaceable
front edge.
2000 668 780
A2-1A
1800 668 780
A2-1B
1600 668 780
A2-1C
1500 668 780
A2-1D
1200 668 780
A2-1E
2000 668 780
A2-2A
1800 668 780
A2-2B
1600 668 780
A2-2C
1500 668 780
A2-2D
1200 668 780
A2-2D
Lowering mechanism, with superstructure
that is vertically extended by electric motor
drive, and with a safety shut-off strip.
For accepting 6 HU Euro inserts.
Prepared for addition of an EcoTecSP or
InForm system table.
Height of superstructure body in raised
state: 1135 mm
Lowering mechanism, with superstructure
that is vertically extended by electric motor
drive, and with a safety shut-off strip.
1st tier: For accepting System 6 HU inserts
2nd tier: Shelf element with central wall
and shelf panels.
Prepared for addition of an EcoTecSP or
InForm system table.
Height of superstructure body in raised
state:
1st tier: 1135 mm
2nd tier: 1340 mm
InForm add-on table prepared for
connecting to lowering mechanism types of
the A4... and A5... series. Table frame with
welded steel tube apron frame and screwattached aluminium table legs 50 x 50 mm.
Table top 30 mm thick, with replaceable
front edge.
Elabo Training Systems
67
Lowering technology
3 HU fold-away system technology
Technical specifications
InForm tables
with fold-away mechanism
3 HU System
Trapezoidal table with
fold-away mechanism
3 HU System
Trapezoidal table
68
Elabo Training Systems
WxDxH
Article Number
For accepting 342 HP
2000 850 780
A7-1A
For accepting 300 HP
1800 850 780
A7-1B
For accepting 264 HP
1600 850 780
A7-1C
For accepting 240 HP
1500 850 780
A7-1D
For accepting 180 HP
1200 850 780
A7-1E
EcoTec trapezoidal table including electric
motor-driven fold-out extruded aluminium
channel for accepting 3 HE insert panels.
Equipment width: 142 HP
Including industrial cable drag chains for
improved cable feeding.
Height of superstructure in folded-out state:
970 mm.
1400/700 600 780
A7-1M
EcoTec trapezoidal table .
Welded steel tube apron frame made of
40 x 25 mm, 40 x 40 mm
rectangular steel tubing.
Height-adjustable table legs made of
50 x 50 mm square steel tubing.
Height pre-set to 780 mm.
Table top 30 mm thick.
1400/700 600 780
A7-1P
InForm system table including electric
motor-driven fold-out superstructure.
For accepting 3 HU Euro inserts.
Height of body of superstructure in the
folded-out state: 970 mm.
TFT lowering technology
Add-on tables
Technical specifications
Lowering unit for IT training
WxDxH
Article Number
Lowering system body for 2 TFT monitors
2000 170 750
A8-1A
Lowering system body for 2 TFT monitors
1800 170 750
A8-1B
Lowering system body for 1 TFT monitor
900 170 750
A8-1F
1800 170 750
A8-1BZ
Lowering mechanism with electric motordriven vertically raisable and lowerable
TFT monitor brackets and storage areas for
mouse and keyboard.
Floor-mounted wooden body 19 mm thick
with automatically actuated covering flap.
Controlled via cable remote control, attached
to the unit. Monitor mounted with VESA
adaptation 75 x 75 mm or 100 x 100 mm for
TFT sizes up to 19 inches, with a maximum
depth of 80 mm. Body of unit has integrated
cable admission inlet for routing of cables.
Student versions:
Teacher versions:
Lowering system body for 1 TFT monitor
Monitor positioning optional
left, centre, right
A9-1A
Optional lock for electrical locking of the
TFT cover flap.
Add-on tables for TFT unit
EcoTecSP add-on table
prepared for connecting to lowering
mechanism types with TFT monitor brackets.
Table frame with welded steel tube apron
frame and screw-attached steel tube table
legs 50 x 50 mm.
Table top 30 mm thick with
replaceable front edge.
Add-on table
2000 630 750
A1-2A
Add-on table
1800 630 750
A1-2B
Add-on table
900 630 750
A1-2F
Elabo Training Systems
69
Lowering technology
Classroom power supply
Technical specifications
WxDxH
Article Number
Floor unit
Classroom power supply
EcoTecSP
Floor unit prepared for accepting the
19“ / 14 HU grid system.
With front leaf doors shortened at the top,
right-hung, with lock.
The floor unit is divided in depth by a
central panel. The rear compartment is used
as connecting space for the cables and
wires which are wired to terminal blocks.
Access via leaf door in left side wall,
lockable.
525 750 710
A7-8C
Floor unit
Classroom power supply
EcoTecSP
Floor unit prepared for accepting the
19“ / 14 HU grid system.
With front leaf doors shortened at the top,
left-hung, with lock.
The floor unit is divided in depth by a
central panel. The rear compartment is used
as connecting space for the cables and
wires which are wired to terminal blocks.
Access via leaf door in right side wall,
lockable.
525 750 710
A7-8D
Floor unit
Classroom power supply
InForm
Floor unit prepared for accepting the
19“ / 13 HU grid system.
With front leaf doors shortened at the top,
right-hung, with lock.
The floor unit is divided in depth by a
central panel. The rear compartment is used
as connecting space for the cables and
wires which are wired onto terminal blocks.
Access via leaf door in left side wall,
lockable.
525 620 680
A7-8F
525 720 680
A7-8G
525 820 680
A7-8H
Floor unit prepared for accepting the
19“ / 13 HU grid system.
With front leaf doors shortened at the top,
left-hung, with lock.
The floor unit is divided in depth by a
central panel. The rear compartment is used
as connecting space for the cables and
wires which are wired to terminal blocks.
Access via leaf door in right side wall,
lockable.
525 620 680
A7-8J
525 720 680
A7-8K
525 820 680
A7-8L
Floor unit
Classroom power supply
InForm
70
Elabo Training Systems
Insert panels 19“
Technical specifications
W x H
Article Number
Main power supply unit
Elabo 19“ / 4 HU insert panel, main power
supply unit usable for 1/N/PE ~ 50 Hz 230 V
or 3/N/PE ~ 50 Hz 230/400 V 45…63 A.
For switching on and protecting the
classroom power supply.
Wiring via block terminals.
Equipment:
1 F I residual current circuit breaker 4p63A
selective, Rated leakage current <= 300 mA,
1m
otor protection switch 45...63 A with
undervoltage release,
1 key switch I/O,
1 automatic circuit breaker 1p6AB,
1 e mergency-OFF switch
(acting on the motor protection switch)
3-phase indicator lights.
483
68-1K.3
Main power supply unit
Elabo 19“ / 4 HU insert panel, main power
supply unit usable for 1/N/PE ~ 50 Hz 230 V
or 3/N/PE ~ 50 Hz 230/400 V 45…63 A.
For switching on and protecting the
classroom power supply.
Wiring via block terminals.
Equipment:
1 F I residual current circuit breaker 4p63A
selective, Type B, AC/DC sensitive for
smooth DC fault currents <= 300 mA,
1m
otor protection switch 45...63 A with
undervoltage release,
1 key switch I/O,
1 automatic circuit breaker 1p6AB,
1 e mergency-off switch
(acting on the motor protection switch)
3-phase indicator lights.
483 177
68-1K.3Z008
Circuit protection unit
Alternating current
19“ / 4 HU insert panel
Circuit protection unit for 1-pole power
supply to student‘s table. With cut-out and
lettering to accept a maximum of
21 x 1-pole automatic circuit breakers.
Empty spaces are provided with covers.
The panel is pre-wired to terminal blocks.
483 177
68-1L.3Z1..
483 354.8
68-1M.3Z3..
177
z = Please state the number of automatic
circuit breakers required.
Circuit protection unit
Three-phase current
19“ / 8 HU insert panel
Circuit protection unit for 3-pole power
supply to student‘s table. With cut-out and
lettering to accept a maximum of
21 x 3-pole automatic circuit breakers.
Empty spaces are provided with covers.
The panel is pre-wired to terminal blocks.
z = Please state the number of automatic
circuit breakers required.
Elabo Training Systems
71
Lowering technology
Lowering mechanism controls
Central up/down control
for lowerable superstructures
Technical specifications
WxDxH
Article Number
Operating panel with push buttons for
up/stop/down control of
lowerable superstructures
19“ / 2 HU insert panel
Depending on the lowerable
superstructures provided, 3 push buttons
are installed per table. Using a group
function, all lowerable superstructures can
be jointly controlled.
B = 483 H = 88.1
68-1X.3Z..
B = 483 H = 88.1
68-1X.3Z4..
104 51 68
A7-8S
19“ / 1 HU blank panel
B =483 H = 43.6
51-1A.3
19“ / 1 HU blank panel
with ventilation slots
B =483 H = 43.6
51-1L.3
19“ / 2 HU blank panel
B =483 H = 88.1
51-1B.3
19“ / 3 HU blank panel
B =483 H = 132.5
51-1C.3
19“ / 4 HU blank panel
B =483 H = 177
51-1E.3
19“ / 6 HU blank panel
B =483 H = 266
51-1D.3
z = Please state the number of operating
buttons required for the lowering
mechanism.
Central up/down control
for fold-away mechanism
Operating panel with push buttons for
up/stop/down control of
fold-away superstructures
19“ / 2 HU insert panel
Depending on the lowerable
superstructures provided, 3 push buttons
are installed per table. Using a group
function, all fold-away superstructures can
be jointly controlled.
z = Please state the number of operating
buttons required for the folding mechanism.
Local up/down control
with key
for lowering mechanisms
Individual control up/down with
key switch on table.
Installed in plastic housing.
(Not usable for TFT technology)
Blank panel
72
Elabo Training Systems
Technical specifications
Wireless up/down control
Transmitter
Wireless remote control for the lowering
mechanisms. Hand-held transmitter for
remote operation of up to 48 receivers,
singly or in groups. In each case,
16 receivers are combined in one group.
WxDxH
Article Number
68-1Y Z01
There are 3 groups.
Wireless up/down control
Receiver
Wireless remote control for the lowering
mechanisms. Receiver for lowering
mechanism on each table, installed in the
body of the lowering system.
68-1Y Z02
Network module for
controlling lowering mechanism
Base network module with in each case
8 digital outputs and inputs for the
following applications:
N3-2A
- Enable power supply / enable table
- Actuation of EMERGENCY-Off
- Control of lowering mechanism
Note: For the necessary control software,
see the chapter on Virtual Equipment.
Elabo Training Systems
73
74
Elabo Training Systems
Electronics
Using 3 HU insert panels
from Elabo, aluminium
channels and similar are
equipped with simple basic
power supply devices as
well as with DC stabilizers
and multimeters (both are
also available as remote
controlled versions).
Most users equip an Elabo
superstructure with the
following standard items:
a main power control panel,
a central superstructure fuse
system (with connection to
the emergency-off), safetytype shockproof sockets and
power supply inserts
(e.g. AC and DC voltage
supply), as well as measuring inserts. Over and above
that, there are practically
no limits on how to
customize the set-up.
The superstructures may
also be equipped with insert
panels and high-performance inserts. For this
purpose people prefer to use
the larger 6 HU system into
which – by means of assembly supports – devices from
the more finely structured
3 HU system can also be
integrated.
Elabo Training Systems
75
Electronics
Precise. Reliable. Very user-friendly
With inserts from Elabo electrical instruments can be
integrated in modular fashion into superstructures. The
range extends from simple insert panels to inserts
with remote-controlled power supply and measuring
devices. It comprises all the items of equipment that are
logically required for training in a wide range of electrical
professions. Highly compact electrical engineering study
stations can thus be created in an extremely efficient way.
Measuring and testing devices
Rapid installation and replacement
The measuring and testing devices are the
core of the inserts. They are characterized
by their accuracy and they consistently
provide high measuring precision over a
large number of years.
The inserts can be rapidly replaced at any
time. The mains connection plug, which
permits contact to be quickly made with
the integrated mains cable harness without
the need for any tools, is installed in the
respective rear wall. The partially integrated
guide rails facilitate the replacement
process.
Power supply devices
The current/voltage supply devices (AC/DC)
are available in analog and digital versions.
They are equipped with reverse polarity
protection and short-circuit resistance.
Intelligent mains power control
panels from Elabo: they can
be switched in two stages. In
the first stage safe low-voltage
devices are activated. In the
second stage, devices that deliver mains voltage at the outlet
are energized. By implementing
many such well thought-out
solutions, derived from practical
experience, Elabo helps ensure
greater safety during the training
procedures.
Insert panels from Elabo
perform a very wide range of
functions. The ones shown here
can be used for connecting up
devices with connection plugs
or for drawing mains voltage by
means of safety-type laboratory
plugs for the experimental test
set-ups.
76
Elabo Training Systems
Regulatable voltage supply
systems are essential for
practical technical instruction. Elabo offers single or
dual-voltage stabilizers which
can be optionally equipped
with an Ethernet interface.
Elabo offers the complete range
of equipment needed for instruction purposes – for example
high-grade devices such as function generators, multimeters and
oscilloscopes, as well as simple
power supply devices for AC and
DC, and the standard types of
equipment from connection jacks
to soldering stations. All from
one single source.
Switchable to mains or low voltage
Electronics for the 19” system
A great deal of emphasis is placed on
safety. For example, Elabo power control
panels can be switched to mains and/or
low voltage. This ensures that the students
are provided only with low voltage for
certain training exercises. Accidents and
mishandling are largely eliminated in this
way.
On request, Elabo can supply electronic
devices for the 19” grid. In the case of the
smaller 3 HU devices, assembly supports
are available that allow them to be used
in the 19” grid. In this way, they can also
be integrated into the superstructures of
other manufacturers which are designed
for the 19” grid.
Extract from the comprehensive range
of equipment available:
Data integration and networking are becoming increasingly
important for training purposes.
By means of the digital multimeter measured values can be
transmitted via interfaces to the
PC. The Elabo test software
performs automatic recordkeeping.
Elabo also offers oscilloscopes
for those experiments in which
it is necessary to display the
course of voltages and currents
over periods of time. The devices
may be operated directly through
the front operating panels, but
remote control via a network is also
possible.
Mains power control panels
Socket panels
Low-voltage power supply units
Continuity testers
Soldering stations
Networking and interface connections
Pneumatics
AC supply units, single-phase, three-phase
DC stabilizers, single/dual
Fixed voltage sources
Combined AC and DC supply units
Multimeters
Oscillospcopes
Frequency generators
Elabo Training Systems
77
Electronics
Construction details
There are two design options available: the
6 HU and 3 HU systems. Due to size the
6 HU system is used mainly for heavy-duty
requirements. The 3 HU system however is
for applications with smaller outputs and
compact construction.
There are different grid widths depending
on the system. This is depicted in width
units (WU) in the 6 HU system. A width
unit is equal to 111.5 mm. Plug-in modules
are available in grid widths 1, 2, and 4. The
plug-in depth is 260 mm. The number of
the plug-in modules to be equipped
conforms to the width of the assembly.
Elabo plug-in modules can be
combined in such an extraordinarily sophisticated and spacesaving manner. The extremely
high equipment density that can
be attained makes it possible to
design every training station in
a compact manner with optimal
equipment.
The pre-installed power cable
assembly significantly simplifies
the mounting and replacement of
devices. The devices come with
a connector plug. In this manner
contact happens automatically
upon insertion. Sporadically used
high-grade devices are often
used in industry only where they
are acutely needed – our uncomplicated assembly and disassembly technology makes it possible.
Giving customers flexibility is a
typical quality of Elabo.
Elabo Training Systems
It is possible to combine the 3 HU system
in superstructures of the 6 HU system in
simple component racks. So both systems
can be combined optimally with each
other. This produces a unique equipment
density.
In both the 3 HU system and the 6 HU
system insert panels are available for
simpler applications and complex plug-in
modules for mounting the correspondingly
higher number of equipment. The plug-in
modules have side parts that are used for
fastening and mounting individual components. Both variants contain the required
terminals for your system.
Component racks are an
important element for the
precise and solid integration
of the 3HU technology into
the 6HU grid.
78
The international euro-cassette 3 HU
system standardized as per DIN 41494
has, in comparison to the 6 HE system,
significantly smaller unit dimensions. The
height of the boards and plug-in modules
in 3 HU is fixed, corresponding to a total
height of 133.35 mm. The widths are
classified in horizontal pitches (HP) of 5.08
mm. Elabo supplies devices with horizontal
pitches of 4, 6, 8.12, 18, 24, 36, 42, 48, 52,
60 and 66.
Expandable Modules
This may also interest you...
Quality in the long term
Elabo durability and reliability are evident
from many details - from the indestructible
electrical parts to the abrasion-resistant
labels of front panels. The design of the
plug-in modules – with fastenings that
cannot be removed from the front – also
stands for an outstanding service life.
Paints/colours and material
Front panels are made of 3 mm hard
aluminum. By default they come in
light gray RAL 7035.
Electronics for the 19“ System
Elabo supplies electronic devices in the
19“ grid upon request. For the smaller
3 HU devices racks are available which
you can use for the 19“. They can also be
integrated in superstructures of various
other manufacturers designed in the
19“ technology.
The design, material and machining of devices support the
consistency practiced by Elabo
in things durable. The front
panels, for example, are made
of 3 mm thick aluminum which
is very stable and completely
non-corrosive. They are inserted
flush into the superstructures.
Fastening screws that invite unauthorized handling are hidden.
The surfaces have a scratchproof powder coating. Due to
the screen print application the
labels and symbols are second
to none in abrasion-resistance.
So you can use the devices
without difficulty even
after many years.
Superstructures integrate and
protect power supply as well as
measuring and testing devices.
The table area remains free for
work with test objects. Elabo
offers superstructures in the
3 HU and 6 HU systems which
can be combined with each
other.
> More on page 45
Virtual Equipment from Elabo
provides the technology that
integrates devices into a
network. The Elabo software,
EHP EduLab, supports classes
with the most modern
resources. All student stations
can be centrally monitored and
activated, among other things,
using this software.
> More on page 109
Table systems in Elabo’s
modular variety form the basis
of state-of-the-art training
rooms.
> More on page 27
Lowering mechanisms allow
superstructures to disappear
into solid containers. This
protects the equipment, and
the experiment room can also
be as used as a theory room.
> More on page 59
Teaching aids for all requirements in training in the electrical trades and professions has
been offered by Elabo for more
than 30 years. The core
equipment is formed by boards
fitted with original industrial
samples and circuit diagrams as
well as safe connections. They
authentically simulate a practical
work situation.
> More on page 119
Accessories for electronics are
available in many forms:
measurement line holders for
mounting on vertical sections
and measurement lines, power
supply cables, socket assemblies for supplying portable
devices and many more.
> More on page 181
Elabo Training Systems
79
Electronics
6 HU System Insert Panels
Technical specifications
WxH
Article Number
Fault current circuit breaker
Alternating current, Type A
Insert panel 1 WU,
Equipment:
1 fault current circuit breaker
2-pole type A, nominal current 25 A,
nominal fault current 30 mA..
111.5 266
32-0K.3
Fault current circuit breaker
Alternating current, Type B
Insert panel 1 WU,
Equipment:
1 fault current circuit breaker
2-pole type B sensitive to all current types
for smooth fault currents 30 mA,
nominal current 25 A..
111.5 266
32-0L.3
Fault current circuit breaker
Rotary current, Type A
Insert panel 1 WU,
Equipment:
1 fault current circuit breaker
4-pole type A, nominal current 25 A,
nominal fault current 30 mA.
111.5 266
32-0M.3
Fault current circuit breaker
Rotary current, Type B
Insert panel 1 WU,
Equipment:
1 fault current circuit breaker
4-pole type B, sensitive to all current
types for smooth fault currents 30mA,
nominal current 25 A.
111.5 266
32-0N.3
Circuit breaker unit
Alternating current
with voltage selection
Fault current circuit breaker Type B
Insert panel 1 WU,
Circuit breaker and switch unit single
phase with key switch for two circuits.
position I “low voltage”
position II “low voltage and mains voltage”
Equipment:
1 k ey switch 0/I/II,
black, removable in any position
1m
otor circuit breaker 10...16 A
with undervoltage release
1 outer conductor indicator light
1 signal light “mains voltage”
111.5 266
32-0V.3
80
Elabo Training Systems
Technical specifications
W x H
Article Number
Circuit breaker unit
Rotary current
with voltage selection
Insert panel 1 WU
Circuit breaker and switch unit
3-phase with key switch for
two circuits
position I “low voltage“
position II “low voltage and mains voltage“
Equipment:
1 key switch 0/I/II, black,
removable in any position
1 motor circuit breaker 10...16 A
with under-voltage release
3 outer conductor indicator lights
1 signal light “mains voltage“
111.5
32-0W.3
Circuit breaker unit
Alternating current
with remote control
voltage selection
Insert panel 1 WU,
Circuit breaker and switch unit
single phase for two circuits
position I “low voltage”
position II “low voltage and mains voltage”
Controls via Ethernet node
(required separately)
Equipment:
1 illuminated release button
1 contacter,
1 outer conductor indicator light
1 signal light ~25 V,
1 signal light 3~400 V
111.5 266
266
N3-2A
Suitable network module
For description see virtual equipment
Circuit breaker unit
Rotary current
with remote control
voltage selection
Insert panel 1 WU,
Circuit breaker and switch unit
3-phase for two circuits
position I “low voltage”
position II “low voltage and mains voltage”
Controls via Ethernet node
(required separately)
Equipment:
1 illuminated release button
1 contactor
3 outer conductor indicator lights
1 signal light ~25 V
1 signal light 3~400 V
111.5 266
Insert panel 1 WU,
Equipment:
4 shockproof sockets
32-0Q.3
N3-2A
Suitable network module
For description see virtual equipment
Shockproof sockets
32-0P.3
111.5 266
32-1J.3
Optionally available with switch
Elabo Training Systems
81
Electronics
6 HU System Insert Panels
Shockproof sockets
with safety lab jacks
Technical specifications
WxH
Article Number
Insert panel 1 WU,
Equipment:
3 shockproof sockets
3 safety lab jacks
(L1, N,PU)
111.5 266
32-1M.3
111.5 266
32-1M.3Z605
111.5
32-1P.3
Optionally available with mains switch
Shockproof sockets
with safety lab jacks
Insert panel 1 WU,
Equipment:
3 shockproof sockets
5 safety lab jacks
(L1, L2, L3, N, PE)
Optionally available with mains switch
Shockproof sockets
with emergency OFF
Insert panel 1 WU,
Equipment:
1 unwired emergency OFF switch
2 shockproof sockets
266
Optionally available with emergency OFF
visualization via Elabo EHP software
Optionally available with mains switch
CEE socket
Insert panel 1 WU,
Equipment:
1 CEE socket
1 shockproof socket
5 safety lab jacks
(L1, L2, L3, N, PE)
111.5
266
32-1L.3
111.5
266
32-1S.3Z301
Optionally available with mains switch
Ungrounded alternating current
82
Elabo Training Systems
Insert panel 1 WU,
Equipment:
1 s ocket without protective ground
contact for drawing alternating current
230 V / 230 VA
1 shockproof socket
1 equipment circuit breaker
1 illuminated rocker switch
Technical specifications
WxH
Article Number
Low voltage
Alternating current, ungrounded
Insert panel 1 WU,
low voltage ungrounded,
AC 2, 4, 6, 8, 10, 12 V / 10A
Equipment:
4 s afety lab jacks for drawing low
alternating currents
3 equipment circuit breakers
1 illuminated rocker switch
111.5 266
32-1E.3
Low voltage
Alternating current, ungrounded
Insert panel 1 WU,
low voltage ungrounded,
AC 6, 12, 18, 24, 36, 42 V/3A
Equipment:
4 s afety lab jacks for drawing low
alternating currents
3 equipment circuit breakers
1 illuminated rocker switch
111.5 266
32-1F.3
Low voltage
Rotary current, ungrounded
Insert panel 1 WU,
Rotary low voltage ungrounded,
3~23/40 V / 3 A at safety lab jacks
Equipment:
4 s afety lab jacks for drawing rotary
voltage
3 equipment circuit breakers
3 outer conductor indicator lights
1 circuit breaker
111.5 266
32-1G.3
Continuity tester
Insert panel 1 WU,
with two continuity testers
Equipment:
1 electronic, high ohm
continuity tester to a maximum of 5 MOhm
1 low-ohm continuity tester
1 bulb, optical display
4 safety lab jacks
1 illuminated rocker switch
111.5 266
32-1B.3
Soldering station
Insert panel 1 WU,
with temperature-controlled soldering
station 80 W, manufacturer: Ersa
temperature range: 150-400 °C steplessly
adjustable and electronically controlled.
Equipment:
1 shockproof socket
1 soldering iron 810 CDJ
1 storage stand A41
1 illuminated rocker switch
111.5 266
32-1W.3
Elabo Training Systems
83
Electronics
6 HU System Insert Panels
Technical specifications
WxH
Soldering station
Insert panel 1 WU,
with electronically regulated soldering
station 80 W, manufacturer: Weller.
On delivery, soldering tip is potential free
temperature range: up to 450°C
steplessly adjustable
Equipment:
1 LED for optical monitoring
1 shockproof socket
1 soldering iron
1 storage stand
1 illuminated rocker switch
111.5
266
32-1Y.3
Pole selector
Insert panel 1 WU,
15 unwired safety lab jacks as
selectable poles labeled 1 to 15
111.5
266
32-1U.3
Data socket for
Communication technology
Insert panel 1 WU,
UAE 8/8(8/8) Cat.6, unwired
111.5
266
32-1U.3Z607
Compressed air supply
Insert panel 1 WU,
quick connect NW5 for plastic hose 6/4
111.5
266
32-1U.3Z004
84
Elabo Training Systems
Article Number
6 HU System Plug-ins
Technische Daten
WxDx H
Article Number
AC supply
with analog displays,
ungrounded
Insert 2 WU,
AC supply 0...260 V / 3 A,
Alternating current ungrounded with
analog displays
Equipment:
1 analog voltage meter
1 analog current meter
1 s ocket without protective
ground contact
1 equipment circuit breaker
1 illuminated rocker switch
229 260 266
35-2E.3
AC supply
with digital displays,
ungrounded
Insert 2 WU,
AC supply 0...260 V / 3 A,
Alternating current ungrounded with
digital displays
Equipment:
1 digital voltage meter
1 digital current meter
1 s ocket without protective
ground contact
1 equipment circuit breaker
1 illuminated rocker switch
229 260 266
35-3E.3
AC stabilizer ungrounded
with digital displays
Insert 2 WU,
AC stabilizer 1.5...260 V / 5 A, ungrounded,
electromechanical stabilization and
digital displays
Equipment:
1 digital voltage meter
1 d igital current meter can be switched to
power measurement
1 s ocket without protective ground
contact
can be switched to 2 safety lab jacks
1 output on / off
1 equipment circuit breaker
1 illuminated rocker switch
229 260 266
35-5H.3
Optional interface
for inserts, system 6 HU/19“
interface type: Ethernet
The interface connections are located
on the back of the equipment.
Incl. 2 m patch cable
N3-3S Z102
Elabo Training Systems
85
Electronics
6 HU System Plug-ins
Technical specifications
WxDxH
Article Number
AC supply rotary current
with multifunctional display
and interface
Insert 4 WU,
AC supply 3~ 0...230 / 400 V 5A
electromechanical setting of rotary
voltage not ungrounded with multifunction
display and mains voltage.
Two Ethernet interfaces are included for
remote control.
Equipment:
1 multifunction display
1 potentiometer to select voltage
1 CEE socket
5 safety lab jacks
1 shockproof socket
3 safety lab jacks
3 equipment circuit breakers
3 outer conductor indicator lights
1 circuit breaker
464 260 266
36-5A.3Z102
AC/DC supply
Alternating current
Insert 2 WU,
AC/DC supply 0...260 Veff/3 A and AC/DC
0…50 Veff/10 A, direct and alternating
current ungrounded with analog displays,
Effective ripple of direct current: ca. 48%
Equipment:
1 analog voltage meter
1 analog current meter
6 safety lab jacks
1 rotary knob to set current
1 switch from alternating to direct voltage
1 changeover switch 50 V / 260 V
2 equipment circuit breakers
1 illuminated rocker switch
229 260 266
35-0K.3
AC/DC supply
Rotary current
Insert 4 WU,
with steplessly adjustable, not
ungrounded rotary current and direct
current with 5% residual ripple
Equipment:
1 analog voltage meter
3 analog current meters
1 rotary knob to set current
1 switch for rotary or direct current
1 current measurement changeover switch
1 x 5-pole CEE socket
1 shockproof socket for variable current
1 shockproof socket for mains voltage
5 safety lab jacks
2 safety lab jacks for DC voltage
1 ground wire lab jacks
3 equipment circuit breakers
3 outer conductor indicator lights
1 x 4-pole circuit breaker
464 260 266
36-1A.3
86
Elabo Training Systems
AC/DC supply
for energy column
Technical specifications
WxDxH
Article Number
Universal power supply AC/DC only for
installation in energy column 30-0P,
2 x 2 WU inserts system 6 HU above one
another, ungrounded voltages: AC/DC
0…25 Veff/10 A. Not ungrounded
voltages: AC/DC 0…260 Veff/ 2 A, DC 230
Veff / 2 A
229 532
35-0P.3
Equipment:
1 3-pole control unit
1 FI-circuit breaker
1 emergency OFF button
5 safety lab jacks
3 protective ground contact sockets
1 k ey switch to select drawing of all
currents
1 OFF button
3 indicator lights to display all voltage
1 indicator lights to display low voltage
3 thermomagnetic circuit breakers
1 micro-fuse
4 safety lab jacks
2 s afety lab jacks for drawing direct
current
2 s afety lab jacks for drawing alternating
current
4 safety lab jacks
1 ground wire jack
Note: when fault current circuit breakers
are used in classrooms and experiments,
VDE 0100 section 723.4 must be observed!
Elabo Training Systems
87
Electronics
6 HU System Plug-ins
DC stabilizer
Technical specifications
WxDxH
Article Number
Insert 2 WU,
DC stabilizer 0…30 V / 0…3 A
With 4-digit digital displays
and 10-gear potentiometer.
Preset for voltage and current limitation.
Output can be switched off
229 260 266
34-4B.3
Interference voltage at output: 1 mV
Transient time: typically 50, maximum 100 µs
Temperature coefficient: 0.01% / °C
Load balancing 0.015 %
Option Interface
for System 6 HU/19“inserts
interface type: Ethernet
The interface connections are located
on the back of the equipment.
Incl. 2 m patch cable
DC stabilizer
Insert 2 WU,
DC stabilizer 2 x 0…30 V / 2 x 0…3 A
with 4-digit digital displays
and 10-gear potentiometer.
Preset for voltage and current limitation.
Fixed voltage +5 V / 3 A
Output can be switched off
N3-3S Z102
229 260 266
34-4U.3
Interference voltage at output: 1 mV
Transient time: typically 50, maximum 100 µs
Temperature coefficient: 0.01% / °C
Load balancing 0.015 %
Option Interface
for double System 6 HU/19“equalizer
Interface type: 2x Ethernet
The interface connections are located
on the back of the equipment.
incl. 2 x 2 m patch cable
88
Elabo Training Systems
N3-3T Z102
6 HU System Insert Panels
Technical specifications
W x H
Article Number
DC stabilizer
Insert panel 1 WU,
DC stabilizer ±15 V / 1 A and +5 V / 3A
111.5
266
32-1D.3
DC stabilizer
Insert panel 1 WU,
DC stabilizer,
Mains switch with synchronized
output voltage 5 V / 5 A.
Outputs fed to 2 safety lab jacks.
Specification: output power:
25 W, residual ripple: 80 mVp-p,
output tolerance: ± 2.0%,
input regulation: ± 0.5%,
load regulation: ± 1.0%,
overload protection: hiccup mode
111.5
266
32-5M.3
DC stabilizer
Insert panel 1 WU,
DC stabilizer,
Mains switch with synchronized
output voltage 24 V / 6 A,
Outputs fed to 2 safety lab jacks.
Specification:
output power: 150 W,
residual ripple: 150 mVp-p,
output tolerance: ± 1.0%,
input regulation: ± 0.5%,
load regulation: ± 0.5%, overload
protection
111.5 266
32-5P.3
Elabo Training Systems
89
Electronics
6 HU System Insert Panels
Technical specifications
WxH
Article Number
Digital multimeter
Insert panel 1 WU,
Digital multimeter 3 3/4-digit LCD with
mains adaptor for mains operation.
Measurement ranges:
DC 400 mV, 4 V, 40 V, 400 V, 1000 V
400 µA, 4 mA, 40 mA, 400 mA, 2000 mA, 20 A
AC 400 mV, 4 V, 40 V, 400 V, 750 V
400 µA, 4 mA, 40 mA, 400 mA,
2000 mA, 20 A
R 400 W, 4 kW, 40 kW, 400 kW, 4 MW,
40 MW
C 4 nF, 40 nF, 400 nF, 4 µF, 40 µF
F 4 kHz … 4MHz
Basic accuracy:
+/- 0.5% v:M: + 4-digit 0.1%;
Operation type
Continuity check; duty cycle check; logic
test; data hold; peak hold
111.5 266
32-2H.3Z006
Oszilloskop
Insert panel 3 WU (+1 WU),
Digital real time oscilloscope
Delivery includes
Blank panel 31-1 A.
Tektronix TDS 2002
General:
- colour display (1/4 VGA LCD)
- Digital Real Time (DRT)
- 60 MHz
- 1 GS/s sampling rate/channel
- two input channels
- external triggering
- Flank and video trigger
- Trigger view
- Cursor measurement with readout
- Set up memory
- Reference curve memory
- Auto set up
- Vector or point representation
- Menu-led measurement processes
With USB interface on the back
464 266
35-4P.3Z103
Oszilloskop
Insert panel 1 WU,
2/4-channel PC-oscilloscope
with Ethernet interface.
The PC digital oscilloscope is simple to use
and is operated entirely via the included
software.
Technical specifications:
Bandwidth: 150 MHz
Channels:2 channels, class 1,
total mass
Vertical: 2.5 mV/div - 100 V/div,
to 250 V/div with Y-elongation
Time bases 35 ranges from
1 ns/div to 200 s/div
Trigger: Auto, Triggered, Single Shot
Trigger source: CH1, CH2, EXT, mains.
Type: Flank, Impulse width or display
Mains supply: 100 - 230 V/AC 47 - 63 Hz
Optionally available:
Differential voltage sensors
90
Elabo Training Systems
2-channel PC-oscilloscope
35-4Q.3Z102
4-channel PC-oscilloscope
35-4R.3Z102
6 HU System Plug-ins
Blank panel
Mounting rack
Technical specifications
WxDx H
Article Number
Blank panel 1 WU
111.5 266
31-1A.3
Blank panel 2 WU
229 266
31-1B.3
Blank panel 4 WU
464 266
31-1C.3
Mounting rack 2 WU,
2 x 3 HU / 2 x 36 HP
229 260 266
31-4A.3
Mounting rack 4 WU,
2 x 3 HU / 2x 84 HP
464 260 266
31-4B.3
Elabo Training Systems
91
Electronics
3 HU System Insert Panels
Technical specifications
WxH
Fault current circuit breaker
Alternating current, Type A
Insert panel 18 HP,
Fault current circuit breaker
1/N/PE~ 50 Hz 230 V 16 A,
Equipment:
1 fault current circuit breaker 2-pole,
type A, nominal current 25 A,
nominal fault current 30 mA
91.4
Fault current circuit breaker
Alternating current, Type B
24 HP insert panel,
Fault current circuit breaker
1/N/PE~ 50 Hz 230 V 16 A,
Equipment:
1 fault current circuit breaker 2-pole,
type B, sensitive to all current types for
smooth fault currents 30 mA,
nominal current 25 A
121.9
128.5
42-0L.3
Fault current circuit breaker
Rotary current, Type A
24 HP insert panel,
Fault current circuit breaker
3/N/PE ~ 50 Hz 400 V 16 A,
Equipment:
1 fault current circuit breaker 4-pole,
type A, nominal current 25 A,
nominal fault current 30 mA
121.9
128.5
42-0M.3
Fault current circuit breaker
Rotary current, Type B
24 HP insert panel,
Fault current circuit breaker
3/N/PE ~ 50 Hz 400 V 16 A,
Equipment:
1 fault current circuit breaker 4-pole,
type B, sensitive to all current types for
smooth fault currents 30 mA,
nominal current 25 A.
121.9
128.5
42-0N.3
92
Elabo Training Systems
Article Number
128.5
42-0K.3
Technical specifications
WxH
Article Number
Circuit breaker unit
Alternating current
with voltage selection
36 HP insert panel,
Circuit breaker and switch unit
single phase with key switch for release of
two circuits
position I “low voltage”
position II “low voltage and mains voltage”
1/N/PE~50Hz 230 V 16 A
Equipment:
1 automatic circuit breaker, single pole C 16 A
1 key button I/0/II, black
1 off button
2 contactors
1 signal light ‘experiment equipment activated’
including second mains cable harness
121.9 128.,5
42-0V.3
Circuit breaker unit
Rotary current
with voltage selection
36 HP insert panel,
Circuit breaker and switch unit
3 phase with key switch to release two
circuits
position I “low voltage”
position II “low voltage and mains voltage”
3/N/PE~50Hz 400 V 16 A
Equipment:
1 automatic circuit breaker, 3-pole C 16 A
1 key button I/0/II, black
1 off button
2 contactors
3 outer conductor indicator lights
1 signal light ‘experiment equipment activated’
2 including second mains cable harness
182.9 128.5
42-0W.3
Circuit breaker unit
Alternating current
with remote control
voltage selection
36 HP insert panel,
Circuit breaker and switch unit
Single phase release of voltages via
Ethernet node
Release I “low voltage”
Release II “mains voltage”
1/N/PE~50Hz 230 V 16 A
Equipment:
1 automatic circuit breaker, single pole C 16 A
2 contactors
1 outer conductor indicator light
1 signal light ‘experiment equipment activated’
1 illuminated button for switching
on voltage
including second mains cable harness
121.9 128.5
42-0P.3
Suitable network module
For description see virtual Equipment
N3-2A
Elabo Training Systems
93
Electronics
3 HU System Insert Panels
Circuit breaker unit
Rotary current with
remote control
voltage selection
Technical specifications
WxD
HxH
Article Number
36 HP insert panel,
Circuit breaker and switch unit
3-phase,
Release of voltage via Ethernet node
Release I “low voltage”
Release II “mains voltage”
1/N/PE~50Hz 400 V 16 A
Equipment:
1 automatic circuit breaker 3-pole C 16 A
2 contactors
3 external conductor indicator lights
1 s ignal light ‘experiment equipment
activated‘
1 illuminated switch for switching to
current
including second mains cable harness
182.9 128.5
42-0Q.3
Suitable network module
For description see Virtual Equipment
Shockproof sockets
24 HP insert panel,
Equipment:
4 shockproof sockets.
N3-2A
121.9 128.5
44-1L.3
60,4 128,5
44-1W.3
60.4 128.5
44-1X.3
Optionally available with mains switch
Safety lab jacks
12 HP insert panel,
mains voltage,
1/N/PE ~ 50 Hz,
Equipment:
3 safety lab jacks
(L1, N, PE)
Optionally available with mains switch
Safety lab jacks
12 HP insert panel,
mains voltage,
3/N/PE ~ 50 Hz 230 / 400 V
Equipment:
5 safety lab jacks
(L1, L2, L3, N, PE)
Optionally available with mains switch
94
Elabo Training Systems
Emergency shutdown
Technical specifications
WxDxH
Article Number
12 HP insert panel,
Unconnected emergency shutdown switch.
Equipment:
1 emergency OFF switch with detent and
yellow signal ring.
Including 2 switch contacts for
visualization using Elabo EHP Software
60.9 196 128.5
44-1J.3Z701
Necessary network module
see virtual equipment
Emergency OFF
12 HP insert panel,
Unconnected key emergency OFF
Equipment:
1 key emergency OFF with yellow signal ring
60.9 196 128.5
44-1J.3Z702
CEEE Socket
24 HP insert panel,
mains voltage,
3/N/PE ~ 50 Hz 230 / 400 V, 16A an
1 CEE socket.
121.6 128.5
44-2C.3
Optionally available with mains switch
Elabo Training Systems
95
Electronics
Euro-Cassettes and Insert Panels
System 3 HU
Technical specifications
WxDxH
Article Number
Ungrounded alternating current
36 HP cassette,
Alternating current ungrounded
230 V / 230 VA and
mains voltage 1/N/PE ~ 50 Hz 230 V 16 A.
Equipment:
3 shockproof sockets,
1 illuminated rocker switch,
1 transformer with separate coils,
1 equipment circuit breaker TMT1A,
1 t oggle switch,
1 s ocket without protective ground contact
(for ungrounded current),
2 safety lab jacks.
182,9 128,5 196
44-1C.3Z301
Low voltage
Alternating current, ungrounded
24 HP cassette
Low alternating current ungrounded,
AC 6, 12, 24, 42 V / 3 A.
An additional freely switchable bridge
rectifier is installed.
121,9 196 128,5
44-1B.3
Low voltage
Alternating current, ungrounded
36 HP insert panel,
Low alternating current, ungrounded
2, 4, 6, 8, 10, 12 V / 10 A
Equipment:
1 illuminated rocker switch
1 transformer with separate coils
3 thermo-magnetic equipment circuit breakers
4 safety lab jacks
B 182,9 H 128,5
44-4C.3
Low voltage
Rotary current, ungrounded
60 HP insert panel ,
rotary current supply,
AC 3~10/17, 3 V 5A, ungrounded.
Equipment:
1 rotary switch I/0, 3 glow lights,
1 r otary current transformer with
micro-circuit breakers,
3 equipment circuit breakers TMT3A,
4 safety lab jacks.
B 304,8 H 128,5
44-4E.3
Alternating voltage
36 HP cassette,
Alternating current 0..260 V/ 2 A not
ungrounded. Low alternating currents
ungrounded 0…6 V / 15 A, 0…18 V / 6 A
and 0…42 V / 3 A. Also an additional,
freely switchable bridge rectifier is fitted.
Ripple of direct voltage approx. 48 % eff.
182,9 196 128,5
44-1F.3
96
Elabo Training Systems
Technical specifications
WxDxH
Article Number
Alternating and direct voltage
52 HP cassette,
Alternating and direct current ungrounded.
0...260 Veff / 3 A (AC/DC) or
0…50 Veff / 10 A (AC/DC)
with analog display instruments
residual ripple with DC ca. 48%
264.2 196 128.5
44-1P.3
AC stabilizer, ungrounded
66 HP cassette,
AC stabilizer with ungrounded alternating
current 2...260 V/2 A
electromechanical stabilization with
delay regulator and
set value potentiometer
1 x 4-digit digital voltage display
1 X 4-digit digital current display
Can be switched to effective power
335.2 196 128.5
44-5M.3
Optional Interface
for System 3HU inserts,
incl. 12HP blank panel and
2 m patch cable
interface type: 1x Ethernet
The interface connections are on the back
of the equipment.
N3-4S.3Z102
Note: the interface is fitted at the side of
the base equipment.
This widens the equipment by 12 HP.
Adjustable DC stabilizer
24 HP cassette,
DC stabilizer 0...30 V / 2 A with
digital display V/A switchable and 10-gear
potentiometer.
Preset for voltage and current limitation.
Optional Interface
for System 3 HU inserts,
incl. 12 HP blank panel and
2 m patch cable
interface type: 1x Ethernet
The interface connections are on the back
of the equipment.
121.9 196 128.5
45-1Y.3
N3-4S.3Z102
Note: the interface is fitted at the side of
the base equipment.
This widens the equipment by 12 HP.
Elabo Training Systems
97
Electronics
Euro-Cassettes and Insert Panels
System 3 HU
Technical specifications
Adjustable DC stabilizer
36 HP cassette
DC stabilizer 2 x 0…15 V / 2 x 0…2 A
with switchable 4-digit digital display
and 10-gear potentiometer.
pre-set for voltage and current limitation.
Output can be switched off.
The devices can be operated in serial or
parallel connection.
Interference voltage at output: 1 mVe
Transient time: typically 50,
maximally 100 μs
Temperature coefficient: 0,01% / °C
Load equilization 0.015 %
WxDxH
182.9 196 128.5
Optional interface for System 3 HU
double stabilizer incl. 12 HP blank panel and
2 x 2 m patch cable
interface type: 2 x Ethernet
The interface connections are at the back of
the device.
The interface is fitted at the side of the
base equipment. This way the device is
widened by 12 HP.
Adjustable DC stabilizer
42 HP cassette
DC stabilizer 2 x 0…30 V / 2 x 0…2 A
with switchable 4-digit digital display
and 10-gear potentiometer.
Pre-set for voltage and current limitation.
Output can be switched off.
The devices can be operated in serial or
parallel connection.
Interference voltage at output: 1 mVe
Transient time: typically 50,
maximally 100 μs
Temperature coefficient: 0,01% / °C
Load equilization 0,015 %
Optional interface for
System 3 HU double stabilizer
incl. 12 HP blank panel and
2 x 2 m patch cable
interface type: 2 x Ethernet
The interface connections are at the back of
the device.
Note: The interface is fitted at the side of
the base equipment. This way the device is
widened by 12 HP.
98
Elabo Training Systems
Article Number
45-1U.3
N3-4T.3Z102
213.3 196 128.5
45-0K.3
N3-4T.3Z102
Adjustable DC stabilizer
Technical specifications
W x H
76 HP insert
DC stabilizer 0…30 V / 2 x 0…2 A
with switchable 4-digit digital display
and 10-gear potentiometer.
Pre-set for voltage and current limitation.
Output can be switched off.
Interference voltage at output: 1 mVe
Transient time: typically 50,
maximally 100 μs
Temperature coefficient: 0,01% / °C
Load equilization 0.015 %
386.1
128.5
Optional interface for 3HU insert panels
incl. 2 m patch cable
interface type: Ethernet
The interface connections are at the back of
the device.
Adjustable DC stabilizer
84 HP insert
DC stabilizer 2 x 0…30 V / 2 x 0…2 A
with switchable 4-digit digital display
and 10-gear potentiometer.
Pre-set for voltage and current limitation.
Output can be switched off.
The devices can be operated in serial or
parallel connection.
Interference voltage at output: 1 mVe
Transient time: typically 50, maximally
100 μs
Temperature coefficient: 0,01% / °C
Load equilization 0,015 %
Optional interface for
System 3 HU insert panels
incl. 2 x 2 m patch cable
interface type: 2 x Ethernet
The interface connections are at the back of
the device.
Article Number
45-1Y.3Z801
N3-4P Z102
426.7 128.5
45-5U.3Z801
N3-4Q Z102
Elabo Training Systems
99
Electronics
3 HU System Insert Panels
Technical specifications
WxDxH
Article Number
24 HP cassette,
switch mains adaptor with synchronized
output voltage 5 V / 5 A.
Outputs fed to 2 safety lab jacks.
Specification:
output power: 25 W,
residual ripple: 80 mVp-p,
output tolerance: ± 2.0 %,
input regulation ± 0.5 %,
load regulation: ± 1.0 %,
overload protection: Hiccup mode.
B 121.9 H 128.5
45-5M.3
24 HP insert panel,
switch mains adaptor with synchronized
output voltage ± 15 V / 2 A.
Outputs fed to 3 safety lab jacks.
Specification:
output power: 2 x 30 W,
residual ripple: 120 mVp-p,
output tolerance: ± 1.0 %,
input control: ± 0.5 %,
load control: ± 0.5 %,
overload protection: Hiccup mode.
B 121.9 H 128.5
45-5N.3
24 HP insert panel,
switch mains adaptor with synchronized
output voltage 24 V / 6 A,
output power: 150 W,
residual ripple: 150 mVp-p,
output tolerance: ± 1.0 %,
input control: ± 0.5 %,
load control: ± 0.5 %,
overload protection.
B 121.9 H 128.5
45-5P.3
Continuity tester
12 HP cassette,
Continuity check electronic (acoustic)
60.9 196 128.5
42-1F.3
AF test device
24 HP cassette,
NF-test equipment with signal tracker,
Demodulator for amplitude modulated
signals.
Loudspeaker 3 W / 100 Hz…15 kHz,
Load resistances 4 - 8 - 16 Ohm / 25 W
121.9 196 128.5
43-1F.3
Mains switch
100
Elabo Training Systems
Digital multimeter
Technical specifications
WxDxH
Article Number
24 HP insert panel,
Digital multimeter 4 1/2-digit
with manual range selection
Technical specifications:
Direct voltage
Ranges 200 mV, 2 V, 20 V, 200 V, 2000 V
Alternating current (effective value)
Ranges 200 mV, 2 V, 20 V, 200 V, 2000 V
Overload protection up to max. 1000 V
Direct current
Ranges 200 µA, 2 mA, 20 mA, 200 mA,
2 A, 20 A
Alternating current (effective value)
Ranges 200 µA, 2 mA, 20 mA, 200 mA,
2 A, 20 A
Resistances
Ranges 200 Ohm, 2 kOhm, 20 kOhm,
200 kOhm, 2000 kOhm, 20 MOhm“
121.9 196 128.5
41-1N.3
Optional Interfaces
Function generator
RS 232
N3-4P Z101
Ethernet incl. 2 m patch cable
N3-4P Z102
USB
N3-4P Z103
36 HP insert panel,
Function generator 0.2 Hz...2 MHz
Technical specifications:
Mains: 230 V ±10 % / 49-61 Hz.
Frequency conrtrol via potentiometer with
scale and rotary switch in six decade
ranges.
182.9 128.5
43-1V.3
Frequency ranges:
20/200 Hz, 2/20/200 kHz, 2 MHz
Signal forms:
Sine, triangle, square
Sine distortion factor:
<1.5% to 100 kHz, <5% to 2 MHz
Output amplitude:
Uss: max. 20 V idling
type. 10 V on 50 Ohm
Output is secured against idling and
short circuit,
Attenuator -20dB via BNC socket.
DC-offset can be activated:
0 to ±10 V settings
External wobbling:
Modulation input VCO
0...5 V for frequency modulation 100:1
Input impedance approx. 17 kOhm
Elabo Training Systems
101
Electronics
3 HU System Insert Panels
Technical specifications
WxDxH
Article Number
Function generator
Cassette 60 HP,
with LCD display, frequency display
and amplitude (pp or rms)
Signal form: sine, square, triangle
Function generator 0.03 Hz...3 MHz
Frequency counter up to 120 MHz
Amplitude: 2 mV to 10 Vss on 50/600 Ohm
(2 mV to 20 Vss without load)
Output 50 Ohm, 600 Ohm
Attenuation: 0,-20,-40 or -60 dB
Sweep via external controls
305 196 128.5
43-1W.3
Function generator
60 HP cassette,
Function generator 0.01 Hz...20 MHz
with frequency counter.
Signal form: sine, square, triangle
positive and negative impulses
Sine, square: 0.01 Hz ... 20 MHz
Triangle: 0.01 Hz ... 1 MHz
Amplitude: 5 mV to 10 Vss on
50/600 Ohm
(5 mV up to 20 Vss without load)
Integrated sweep, linear or logarithmic
Single sweep triggering (manual, external,
remote controlled)
Input via rotary encoder or
numerical keys or via
ELABO EHP software.
With 4-line illuminated display.
305 196 128.5
Variants:
Oscilloscope
102
Elabo Training Systems
Function generator with RS 232 interface
43-1U.3Z101
Function generator with
Ethernet-interface
43-1U.3Z102
Function generator with USB interface
43-1U.3Z103
52 HP insert panel,
2-channel PC-oscilloscope
with Ethernet-interface.
The PC digital oscilloscope is simple to use
and is operated entirely via the included
software
Technical specifications:
Bandwidth: 150 MHz
Channels: 2 Channels, class 1, total mass
Vertical:2.5 mV/div - 100 V/div,
to 250 V/div with Y-elongation
Time bases:35 ranges of
1 ns/div to 200 s/div
Trigger:
Auto, triggered, single shot,
Trigger source: CH1, CH2, EXT, mains.
Type: Flank, impulse width or delay
Mains power supply:
100 - 230 V/AC
47 - 63 Hz
Optionally available:
Differential voltage sensors
264.2 210 128.5
41-1Q.3Z102
Euro-Cassettes System 3 HU
Technical specifications
WxDxH
Article Number
Oscilloscope
52 HP insert panel,
4-channel PC-oscilloscope with
Ethernet interface.
The PC digital oscilloscope is simple to use
and is operated entirely via the included
software.
Technical specifications:
Bandwidth: 150 MHz
Channels: 4 Channels, class 1, total mass
Vertical:2.5 mV/div - 100 V/div,
to 250 V/div with Y-elongation
Time bases:35 ranges of
1 ns/div to 200 s/div
Trigger:
Auto, triggered, single shot
Trigger source: C H1, CH2, CH3, CH4, EXT,
mains.
Type:
Flank, impulse width or delay
Mains power supply: 1 00 - 230V/AC
47 - 63 Hz
Optionally available:
Differential voltage sensors
264.2 210 128.5
41-1R.3Z102
Soldering station
18 HP cassette,
Soldering station 80W temperature
controlled soldering iron 820 CDJ and
depositing stand A 41.
91.4 196 128.5
46-1A.3
18 HP cassette,
Analog soldering station 80W.
Analog control electronics for
soldering tools up to 80 W, temperature
range 150°C - 450°C, temperature control
by rotary potentiometer.
With 80 W Silver Line soldering iron
WSP 80 and soldering tip LT B and
a safety depositing stand WPH 80,
Manufacturer: Weller WS 81.
91.4 196 128.5
46-1H.3
36 HP cassette,
Multifunctional soldering and de-soldering
station comprising: - ERSA soldering station
DIGITAL 2000 A complete with soldering
iron power tool 24 V/80 W and storage
stands 0A 42. - ERSA de-soldering station
DIGITAL 2000 A with vacuum unit with
de-soldering tool X-Tool 24 V / 2 x 60 W
and depositing stand OA 44.
182.9 196 128.5
46-1M.3
Soldering/final soldering station
Elabo Training Systems
103
Electronics
3 HU System Insert Panels
Technical specifications
WxD
HxH
Article Number
Pole selector
18 HP insert panel,
9 safety lab jacks as selectable poles,
6 jacks labeled 1…6,
3 jacks labeled A, B, C,
2 BNC integrated jacks 50 Ohm.
All unwired.
91.4 128.5
46-1D.3
Supply strip
6 HP supply strip,
interface field LPT parallel.
Equipment:
1 Sub-D plug-in connector 25-pole.
female with approx. 3 m connector wire and
mating plug.
30.2 128.5
46-7A.3
6 HP supply strip,
interface field COM / RS232 serial.
Equipment:
1 sub-D plug-in connector 25-pole male
with approx. 3 m connector wire and
mating plug
30.2 128.5
46-7B.3
6 HP supply strip,
interface field COM / RS232 serial.
Equipment:
1 sub-D plug-in connector 9-pole male with
approx. 3 m connector wire and mating plug
30.2 128.5
46-7C.3
6 HP supply strip,
interface field VGA.
Equipment:
1 sub-D plug-in connector 15-pole HD male
with approx. 3 m connector wire and
mating plug
30.2 128.5
46-7D.3
104
Elabo Training Systems
(Supply strip continued)
Technical specifications
W x H
Article Number
6 HP supply strip,
interface field DVI-I.
Equipment:
1 DVI-I plug-in connector female with
approx. 3 m connector wire and mating plug
30.2 128.5
46-7E.3
6 HP supply strip,
interface field USB.
Equipment:
2 USB-plug-in connectors type A female
with approx. 3 m connector wire and
mating plug.
30.2 128.5
46-7F.3
6 HP supply strip,
interface field PS/2.
Equipment:
2 PS/2 Mini-DIN 6-pol. plug-in connectors
female with approx. 3 m connector wire and
mating plug.
30.2 128.5
46-7G.3
6 HP supply strip,
interface field Audio L - Audio R.
Equipment:
2 Cinch plug-in connector red and white
female with approx. 2.5 m connector wire
and mating plug.
30.2 128.5
46-7H.3
Elabo Training Systems
105
Electronics
3 HU System Insert Panels
(Supply strip continued)
106
Elabo Training Systems
Technical specifications
WxD
HxH
Article Number
6 HP supply strip,
interface field Audio.
Equipment:
1 jack socket 3.5 mm Stereo with approx.
3 m connector wire and mating plug.
30.2
128.5
46-7J.3
6 HP supply strip,
interface field FireWire.
Equipment:
1 plug-in connector IEEE-1394 6-pole
with approx. 3 m connector wire and
mating plug.
30.2
128.5
46-7K.3
HP supply strip 6,
interface field RJ45 network jack.
Equipment:
1 RJ45 jack 8-pole for plugging on
both sides.
30.2 128.5
46-7L.3
6 HP supply strip,
interface field S-VHS.
Equipment:
1 PS/2 Mini-DIN 4-pole plug-in connector
female with approx. 2 m connector wire and
mating plug.
30.2 128.5
46-7M.3
6 HP supply strip,
interface field IEEE-488 / GPIB.
Equipment:
1 IEEE-488 Centronics 24-pole female
with 2 m connector wire and mating plug.
30.2 128.5
46-7N.3
Technical specifications
W xxHH
Article Number
(Supply strip continued)
6 HP supply strip,
BNC interface.
Equipment: 2 BNC integrated sockets
50 Ohm, can be plugged on both sides.
30.2
128.5
46-7P.3
Compressed air supply
6 HP compressed air supply,
1 quick connection coupling NW 5 1/8“
including 1 plug-on cap NW 5 for
plastic hose 6/4
30.4 128.5
48-1K.3
Compressed air supply
36 HP insert panel,
Compressed air supply unit 0.5...10 bar.
Equipment: 1 pressure reduction valve,
1 manometer 0…10 bar, Kl. 2.5,
1 single hand quick closure NW 2.5
Extraction of unreduced compressed air
max. 12 bar,
1 single handed quick closure NW 2.5
Withdrawal of compressed air as
setting 0...10 bar,
1 plug-on cap NW 2.5
182.9 128.5
48-1G.3
Potential equalization
6 HP potential equalization,
1 plug-on connector for potential
equalization POAG-ID6, unwired
30,4 128.5
46-1D.3Z840
Elabo Training Systems
107
Electronics
3 HU System Insert Panels
Blank panel
108
Elabo Training Systems
Technical specifications
WxD
HxH
Article Number
Blank panel 4 HP
20.3
128.5
40-1H.3
Blank panel 6 HP
30,4
128.5
40-1G.3
Blank panel 8 HP
40.5
128.5
40-1J.3
Blank panel 12 HP
60.9 128.5
40-1A.3
Blank panel 18 HP
91.4 128.5
40-1B.3
Blank panel 24 HP
121.9 128.5
40-1C.3
Blank panel 36 HP
182.9 128.5
40-1D.3
Blank panel 42 HP
213.3 128.5
40-1E.3
Blank panel 48 HP
243,8 128.5
40-1F.3
Blank panel 60 HP
304,8 128.5
40-1K.3
Blank panel 96 HP
487,6 128.5
40-1L.3