CLEANING INSTRUCTIONS
If the pressure gauge on your filter reads 5 PSI or higher than the
original starting pressure, the filter needs to be cleaned. The ClearWater
II D.E. Filter System features the exclusive 1-2-3 Safety Locking System
to ensure safe and simple filter maintenance.
1. Turn off pump. WARNING: Never attempt to clean filter while pump is running. This is a pressurized vessel. It could cause severe injury or harm to your person. Plug skimmer and pool return lines or drain pool water level to below pool return line.
2. Slowly open the air release knob on top of filter until the pressure gauge reads “0”. Open drain cap at bottom of filter and allow water to flow.
3. Press the yellow safety latch on the underside of the locking nut and
turn the nut counterclockwise to remove the lid. Rinse the D.E. element with a garden hose. There is no need to remove the element from the filter.
4. Reassemble lid and follow start-up procedures from original instructions.
My Original Starting Pressure is ________ PSI (Pounds per
Square Inch). I should clean the filter at ________ PSI.
LIMITED WARRANTY
Waterway Plastics manufactures its products and equipment in accordance
with very high standards of workmanship. We use the best materials available
and maintain the highest quality procedures practical in the industry. In
accordance, Waterway warrantys its products as follows:
replacement, the body will be exchanged for a new tank on an adjusted
service pro-rata life basis. Charges to the owner, on the pro-rata life basis, will
be determined by the actual number of months installed beginning with the
date of installation.
All plastics parts such as jets, valves, skimmers,manifolds, suctions, lights,
and other plastic components manufactured by Waterway will be replaced or
repaired, if the defects are determined by Waterway to be the responsibility of
Waterway Plastics, for a period of three years from the date of installation. The
warranty does not cover filter cartridges, D.E. grids, O-rings, pressure gauges,
pump seals, light bulbs or any parts not manufactured by Waterway. Warranty
applies to OEM’s and Distributors of Waterway Products.
Products that fail or become defective during the warranty period, except as a
result of improper installation, bad water chemistry, accidents or negligence
on behalf of the owner, freezing, earthquakes, fire floods, or other acts of
nature, shall be repaired or replaced at Waterway’s option without charge
to the owner. This process will be completed within 90 days of receipt of the
defective product barring delays caused by the acquisition of component parts
not manufactured at our facility.
The Supreme and Hi-Flo Pumps will receive limited warranty from any defect
in material or workmanship for one year from the date of manufacture. This
includes the motor but not the motor seal.
To obtain warranty replacements or repair, defective products should be
returned (transportation paid) to the place of purchase, or to Waterway. It
should include a description of the defect and the circumstances surrounding
the incident or problem.
All thermoplastic molded filter bodies and rotational molded sand filter bodies
have a warranty of ten years, warranted on a pro-rata life basis.If a defect
becomes apparent during the first year, the body will be exchanged for a
new body if the defects are determined by Waterway to be the responsibility
of Waterway Plastics. If a defect becomes apparent after the first year from
the date of manufacture which, in the opinion of Waterway, will require
© Copyright 2008 Waterway Plastics
Waterway shall not be responsible for cartage, removal and/or reinstallation
labor, or any other such costs incurred in obtaining warranty replacements.
Warranty applies to OEM’s and Distributors of Waterway Products.
This warranty gives you specific legal rights. You may also have other rights
which very from state to state.
2200 East Sturgis Road, Oxnard, CA 93030 • Ph. (805) 981-0262 • Fax (805) 981-9403
www.waterwayplastics.com • waterway@waterwayplastics.com
STANDARD SYSTEM
OWNER’S MANUAL
810-0079.1008
CLEARWATER II D.E. FILTER SYSTEM OWNER’S MANUAL
Our ClearWater II D.E. Filter System is shipped from Waterway complete
with everything you need right in the box. Assemble filter system only
after above-ground pool is installed. Fill pool with water. Do not raise
water level above pool return line.
The pool equipment should be located between pool skimmer and
return line. The filtration system should not be closer than 2 ft. and not
further than 5 ft. from the pool. The ClearWater II D.E. Filter System
needs to be on a completely flat surface (e.g. patio block, cement slab,
etc.). The pump will require a 110 volt/20 amp service.
CLEARWATER II D.E. FILTER SYSTEM REPLACEMENT PARTS
WARNING: A GFCI is required. Follow national and local
building and safety codes.
Before opening shipping carton, make sure box is in the upright
position. Inside the carton, you will find:
1. One base
2. One pump (packaged in separate box)
3. One filter
4. Two lengths of 6 ft. hose
5. One bag with fittings
INSTALLATION INSTRUCTIONS
WARNING! READ ALL INSTRUCTIONS AND WARNING
LABELS BEFORE OPERATING FILTER!
1. Place filter and base on a level, secure surface. Place the pump on the base to the left of the filter. The pump should now be facing the filter marked “Inlet”. There is no need to disassemble filter or pump assemblies.
(Detail 2, #21 & 22). Thread into the outlet side of the filter tank.
7. Remove 4 hose clamps from the fittings bag. Select one of the hose lengths and slip one clamp over the end of hose adapter. Place the end of the hose on to the hose adapter (pump suction) and the other end to the hose adapter end of the pool skimmer. Repeat steps with filter outlet to pool return.
2. Open pump trap lid and remove 2" gasket. Place 2" gasket into union 8. Remove the Lid Handle, #1, from the fittings bag and attach it to nut. Hand tighten union nut to suction side of pump (Detail 5).
the top of the Lid Assembly, #12, as shown (Detail 6). Secure ClearWater Filter to ClearWater Filter Base using #24a Phillips Head 3. Secure pump to the base using the pin & anchor assemblies Screws (2) (Detail 6a & 6aa). Fill pool until water level is halfway up (Detail 4).
length of skimmer throat.
4. Open fittings bag and remove coupling assembly (Detail 2). 9. Open air release knob. Plug in and turn on pump. Air will pass out Assemble 2" gasket, coupling, coupling O-Ring, and 2" union nut, of the filter through the air release knob. Once water discharges from and thread into inlet side of filter.
knob, close it.
5. Thread 2" union nut to pump discharge (Detail 3). Thread hose NOTE: To remove Lid Assembly, take off Filter Nut, #3, insert Filter adapter with O-Ring, to pump trap suction side (Detail 1).
Wrench, #20a, in notch between Filter Body, #20 and Lid Assembly, 6. From the fittings package, remove 11/2" hose adapter and O-ring #12, twist and separate as shown in Detail 6a.
33
22
32
27
21
27
20
21
26
21 22
21
26
25
Item Part No. 1
519-7601 2
819-9002 3
718-7251 4
602-0200 5
805-0207 6
830-4000SS 7
519-7451 8
805-0224 9
519-7430 10 805-0117SD 11 805-0460 12 519-7411 519-7401 13 519-7441 14 500-7310 15 718-7210 16 419-7241 17 519-7269 18 550-7210 550-7220 19 550-7100 550-7120 20 515-7251 20a 519-7470 21 805-0224 22 417-6241 23 500-5300 24 672-7401 24a 819-0044 25 415-5001 26 419-7241 27 711-4010 28 429-7221 29 PH1100 PH1150 PH1200 PH2100 PH2150 PH2200 30 310-6500 31 319-3230 32 805-0436 33 319-3260 Description
Lid Handle
#12 x 3/4" S/S Phillips Head Screw
Filter Locknut Assembly
Air Relief Plug
O-Ring - Air Relief
Pressure Gauge
Handle Assembly (2)
O-Ring - Air Relief
Gauge - Fitting Adapter
O-Ring - Adapter
Lid O-Ring
Lid Assembly (Small)
Lid Assembly (Large)
Wing-Nut
Screen/Sock Assembly
Tie Nut - D.E.
Plug - 2" x 1 1/2" MPT
Locator - Top Grids - D.E.
D.E. Grids - 12 sq. ft. (7)
D.E. Grids - 18 sq. ft. (7)
Base Assembly - 12 sq. ft.
Base Assembly - 18 sq. ft.
Filter Body Bottom
Filter Wrench (see Detail 6a)
O-Ring (4)
1 1/2" MPT x 1 1/2" Male Smooth
Hose Adapter (2)
Drain Assembly
ClearWater II Base
#10 x 1" S/S Phillips Head Screw (2)
2" Union Nut
Coupling
2" Union Gasket (2)
Snap Pin (4)
1 HP - 1-Speed Hi-Flo Pump
1 1/2 HP - 1-Speed Hi-Flo Pump
2 HP - 1-Speed Hi-Flo Pump
1 HP - 2-Speed Hi-Flo Pump
1 1/2 HP - 2-Speed Hi-Flo Pump
2 HP - 2-Speed Hi-Flo Pump
6" Trap - 1 1/2" Buttress x 2" Flange
6" Basket Assembly
O-Ring
6" Trap Lid
28
25
DETAIL 1
DETAIL 2
DETAIL 3
21
1
27
31
30
29
DETAIL 5
DETAIL 6
3
28
DETAIL 4
DETAIL 6aa
3
4
7
5
10
6
20a
7
8
9
11
12
24a
12
20
13
14
15
24a
16
17
DETAIL 6a
18
19
33
22
20
32
27
21
26
21 22
25
28
30
24a
2
1
31
21 23
30
32
21
29
31
2
33
22
28
21 23
29
24
24a (2)
Download PDF
Similar pages