- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- User manual
advertisement
CLEANING INSTRUCTIONS
If the pressure gauge on your filter reads 5 PSI or higher than the original starting pressure, the filter needs to be cleaned. The ClearWater
II D.E. Filter System features the exclusive 1-2-3 Safety Locking System to ensure safe and simple filter maintenance.
3. Press the yellow safety latch on the underside of the locking nut and
turn the nut counterclockwise to remove the lid. Rinse the D.E.
element with a garden hose. There is no need to remove the element
from the filter.
1. Turn off pump. WARNING: Never attempt to clean filter while
pump is running. This is a pressurized vessel. It could cause
severe injury or harm to your person. Plug skimmer and pool
return lines or drain pool water level to below pool return line.
4. Reassemble lid and follow start-up procedures from original
instructions.
My Original Starting Pressure is ________ PSI (Pounds per
Square Inch). I should clean the filter at ________ PSI.
2. Slowly open the air release knob on top of filter until the pressure
gauge reads “0”. Open drain cap at bottom of filter and allow water
to flow.
Waterway Plastics manufactures its products and equipment in accordance with very high standards of workmanship. We use the best materials available and maintain the highest quality procedures practical in the industry. In accordance, Waterway warrantys its products as follows:
All plastics parts such as jets, valves, skimmers,manifolds, suctions, lights, and other plastic components manufactured by Waterway will be replaced or repaired, if the defects are determined by Waterway to be the responsibility of
Waterway Plastics, for a period of three years from the date of installation. The warranty does not cover filter cartridges, D.E. grids, O-rings, pressure gauges, pump seals, light bulbs or any parts not manufactured by Waterway. Warranty applies to OEM’s and Distributors of Waterway Products.
The Supreme and Hi-Flo Pumps will receive limited warranty from any defect in material or workmanship for one year from the date of manufacture. This includes the motor but not the motor seal.
All thermoplastic molded filter bodies and rotational molded sand filter bodies have a warranty of ten years, warranted on a pro-rata life basis.If a defect becomes apparent during the first year, the body will be exchanged for a new body if the defects are determined by Waterway to be the responsibility of Waterway Plastics. If a defect becomes apparent after the first year from the date of manufacture which, in the opinion of Waterway, will require
LIMITED WARRANTY
replacement, the body will be exchanged for a new tank on an adjusted service pro-rata life basis. Charges to the owner, on the pro-rata life basis, will be determined by the actual number of months installed beginning with the date of installation.
Products that fail or become defective during the warranty period, except as a result of improper installation, bad water chemistry, accidents or negligence on behalf of the owner, freezing, earthquakes, fire floods, or other acts of nature, shall be repaired or replaced at Waterway’s option without charge to the owner. This process will be completed within 90 days of receipt of the defective product barring delays caused by the acquisition of component parts not manufactured at our facility.
To obtain warranty replacements or repair, defective products should be returned (transportation paid) to the place of purchase, or to Waterway. It should include a description of the defect and the circumstances surrounding the incident or problem.
Waterway shall not be responsible for cartage, removal and/or reinstallation labor, or any other such costs incurred in obtaining warranty replacements.
Warranty applies to OEM’s and Distributors of Waterway Products.
This warranty gives you specific legal rights. You may also have other rights which very from state to state.
© Copyright 2008 Waterway Plastics
2200 East Sturgis Road, Oxnard, CA 93030 • Ph. (805) 981-0262 • Fax (805) 981-9403 www.waterwayplastics.com • [email protected]
810-0079.1008
STANDARD SYSTEM
OWNER’S MANUAL
CLEARWATER II D.E. FILTER SYSTEM OWNER’S MANUAL
Our ClearWater II D.E. Filter System is shipped from Waterway complete with everything you need right in the box. Assemble filter system only after above-ground pool is installed. Fill pool with water. Do not raise water level above pool return line.
WARNING: A GFCI is required. Follow national and local building and safety codes.
The pool equipment should be located between pool skimmer and return line. The filtration system should not be closer than 2 ft. and not further than 5 ft. from the pool. The ClearWater II D.E. Filter System needs to be on a completely flat surface (e.g. patio block, cement slab, etc.). The pump will require a 110 volt/20 amp service.
Before opening shipping carton, make sure box is in the upright position. Inside the carton, you will find:
1. One base
2. One pump (packaged in separate box)
3. One filter
4. Two lengths of 6 ft. hose
5. One bag with fittings
WARNING! READ ALL INSTRUCTIONS AND WARNING
LABELS BEFORE OPERATING FILTER!
1. Place filter and base on a level, secure surface. Place the pump on
the base to the left of the filter. The pump should now be facing the
filter marked “Inlet”. There is no need to disassemble filter or pump
assemblies.
2. Open pump trap lid and remove 2" gasket. Place 2" gasket into union
nut. Hand tighten union nut to suction side of pump (Detail 5).
3. Secure pump to the base using the pin & anchor assemblies
(Detail 4).
4. Open fittings bag and remove coupling assembly (Detail 2).
Assemble 2" gasket, coupling, coupling O-Ring, and 2" union nut,
and thread into inlet side of filter.
5. Thread 2" union nut to pump discharge (Detail 3). Thread hose
adapter with O-Ring, to pump trap suction side (Detail 1).
6. From the fittings package, remove 11/2" hose adapter and O-ring
INSTALLATION INSTRUCTIONS
(Detail 2, #21 & 22). Thread into the outlet side of the filter tank.
7. Remove 4 hose clamps from the fittings bag. Select one of the hose
lengths and slip one clamp over the end of hose adapter. Place the
end of the hose on to the hose adapter (pump suction) and the other
end to the hose adapter end of the pool skimmer. Repeat steps with
filter outlet to pool return.
8. Remove the Lid Handle, #1, from the fittings bag and attach it to
the top of the Lid Assembly, #12, as shown (Detail 6). Secure
ClearWater Filter to ClearWater Filter Base using #24a Phillips Head
Screws (2) (Detail 6a & 6aa). Fill pool until water level is halfway up
length of skimmer throat.
9. Open air release knob. Plug in and turn on pump. Air will pass out
of the filter through the air release knob. Once water discharges from
knob, close it.
NOTE: To remove Lid Assembly, take off Filter Nut, #3, insert Filter
Wrench, #20a, in notch between Filter Body, #20 and Lid Assembly,
#12, twist and separate as shown in Detail 6a.
22
21
31
30
DETAIL 1
33
32
20
27 26
21
25
DETAIL 2
21 22
21
23
27
DETAIL 3
26
21
25
29
Item
21
22
23
24
24a
25
26
16
17
18
19
20
20a
13
14
15
9
10
11
12
7
8
5
6
3
4
1
2
27
28
29
30
31
32
33
28
CLEARWATER II D.E. FILTER SYSTEM REPLACEMENT PARTS
500-5300
672-7401
819-0044
415-5001
419-7241
711-4010
429-7221
PH1100
PH1150
PH1200
PH2100
PH2150
PH2200
310-6500
319-3230
805-0436
319-3260
Part No.
519-7601
819-9002
718-7251
602-0200
805-0207
830-4000SS
519-7451
805-0224
519-7430 Gauge - Fitting Adapter
805-0117SD O-Ring - Adapter
805-0460
519-7411
519-7401
519-7441
500-7310
718-7210
419-7241
519-7269
550-7210
550-7220
550-7100
550-7120
515-7251
519-7470
805-0224
417-6241
Description
Lid Handle
#12 x 3/4" S/S Phillips Head Screw
Filter Locknut Assembly
Air Relief Plug
O-Ring - Air Relief
Pressure Gauge
Handle Assembly (2)
O-Ring - Air Relief
Lid O-Ring
Lid Assembly (Small)
Lid Assembly (Large)
Wing-Nut
Screen/Sock Assembly
Tie Nut - D.E.
Plug - 2" x 1 1/2" MPT
Locator - Top Grids - D.E.
D.E. Grids - 12 sq. ft. (7)
D.E. Grids - 18 sq. ft. (7)
Base Assembly - 12 sq. ft.
Base Assembly - 18 sq. ft.
Filter Body Bottom
Filter Wrench (see Detail 6a)
O-Ring (4)
1 1/2" MPT x 1 1/2" Male Smooth
Hose Adapter (2)
Drain Assembly
ClearWater II Base
#10 x 1" S/S Phillips Head Screw (2)
2" Union Nut
Coupling
2" Union Gasket (2)
Snap Pin (4)
1 HP - 1-Speed Hi-Flo Pump
1 1/2 HP - 1-Speed Hi-Flo Pump
2 HP - 1-Speed Hi-Flo Pump
1 HP - 2-Speed Hi-Flo Pump
1 1/2 HP - 2-Speed Hi-Flo Pump
2 HP - 2-Speed Hi-Flo Pump
6" Trap - 1 1/2" Buttress x 2" Flange
6" Basket Assembly
O-Ring
6" Trap Lid
22
21
31
30
20a
24a
22
33
32
29
DETAIL 5
DETAIL 6a
3
12
20
27
33
24a
32
1
7 6
8
11
9
13
20
17
18
15
1
28
21
31
30
27
26
21
25
28
2
DETAIL 6
19
14
16
2
5
10
3
4
7
12
21 22
21
23
28
DETAIL 4
24a
DETAIL 6aa
29
24
24a (2)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement