Model Buster V
Beef Splitting Band Saw
EQUIPMENT
SELECTION . . . . . . . . . . . . . Ordering No.
TABLE OF
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . Page
Buster V Band Saw (3.3 HP)
460/230V--60Hz . . . . . . . . . . . . . 4006033
380/220V--50Hz . . . . . . . . . . . . . 4006057
42V--50Hz, Cold Water Spray . 4006036
Buster V Band Saw (5 HP)
460/230V--60Hz . . . . . . . . . . . . . 4006172
380/220V--50Hz . . . . . . . . . . . . . 4006247
Spring Balancer . . . . . . . . . . . . . . . . 4042052
Air Balancer (4 feet overall length) 4042016
Air Balancer (20 feet overall length) 4042020
Standard Blade (127 in) . . . . . . . . . 1023159
Cut Tooth Blade (127 in) . . . . . . . . 1023338
JET Blade (127 in) . . . . . . . . . . . . . 1023620
• Safety Messages to Employer and
Safety Director . . . . . . . . . . . . . . . . . . . 2
• Safety Messages to Operators,
Maintenance and Cleanup Personnel 3
• Parts Diagram and List . . . . . . . . . . . . 4
• Specifications . . . . . . . . . . . . . . . . . . . 12
• Installation Instructions . . . . . . . . . . . 12
• Connection Diagrams . . . . . . . . . . . . 12
• Operation Instructions . . . . . . . . . . . . 14
• Maintenance Instructions . . . . . . . . . 15
• Motor Wiring Diagrams . . . . . . . . . . . 16
JARVIS
6206002;;.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
safety messages to employer
and safety director
Model Buster V
page 2 of 16
Keep hands clear.
SAFETY MESSAGES TO EMPLOYER AND SAFETY DIRECTOR
AVOID INJURY
1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove any
malfunctioning equipment.
2. Ensure that all employees who use this tool are trained in the proper use of this tool and are aware of
the dangers that may arise if they do not follow the procedure outlined in this brochure.
3. Enclosed are four (4) copies of “NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP
PERSONNEL.” Post one copy on the employees’ bulletin board; give one copy to the operator(s);
give one copy to the maintenance foreman; and give one copy to the sub-contract cleanup / internal
cleanup foreman. Additional copies will be provided upon request.
4. The tool is designed and intended to be powerful. This fact should be obvious to your employees, but
you must emphasize it to them.
5. Never make modifications or alterations to the tool. Replace any missing or illegible labels.
6. Ensure that proper procedures are established in accordance with OSHA’s lockout/tagout procedures
(29 CFR 1910.147) to prevent accidental startup or release of stored energy.
7. Follow our installation and maintenance instructions for proper installation and care of the tool.
8. Avoid injury. Do not permit the tool to be misused.
9. If you resell or distribute a Jarvis product, you must provide the purchaser with the appropriate safety
sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided upon
request.
JARVIS
6206002;;.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
safety messages to operators,
maintenance and cleanup personnel
Model Buster V
page 3 of 16
Keep hands clear.
SAFETY MESSAGES TO OPERATORS, MAINTENANCE AND CLEANUP
PERSONNEL
REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE
REPORT ANY PROBLEMS TO YOUR SUPERVISOR
1. Disconnect the power supply in accordance with OSHA’s lockout/tagout procedures (29 CFR
1910.147) before making any blade changes.
2. Disconnect the power supply in accordance with OSHA’s lockout/tagout procedures (29 CFR
1910.147) before performing any repairs or maintenance.
3. Disconnect the power supply -- or have the power supply disconnected -- in accordance with OSHA’s
lockout/tagout procedures (29 CFR 1910.147) before performing any cleanup.
4. Disconnect the power supply when the tool is not in use.
5. Never put fingers, hands or other parts of the body on the cutting edge or within the cutting path of the
tool when it is connected to the power supply.
6. Test the tool prior to use or daily. Depress one trigger, then pause one second and depress the other
trigger and the tool should not start. Repeat this procedure reversing the triggers. Depress both triggers simultaneously and the tool should start. With the tool running, release one trigger and the tool
should stop. Continue holding the depressed trigger and then depress the other trigger. The tool should
not start. Repeat this procedure holding the other trigger. If the tool malfunctions, remove it from service and report or repair it immediately.
7. Never depress the triggers unless you want to use or test the tool.
8. Never make modifications or alterations to the tool. Report or replace any missing or illegible labels.
JARVIS
6206002;;.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
parts diagram and list
Model Buster V
page 4 of 16
IDLER END
Figure A
*
**
* Tighten to 37 lbf--ft (50 N--m)
** Use grease gun 8038001
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PART NO.
1055338
1055277
1002227
1061201
1038011**
1007176
1055536
1042127
1021235
1021234
3021006
1057023
1013141
1061220
1029194
1055363
1010481
1042126
1020146
1055021
1036422
1055862
PART NAME
QTY
Flat Head Socket Screw
5
Flat Head Socket Screw
1
Idler Wheel Cover
1
Door Catch
1
Grease Fitting
1
Lock Nut
1
Socket Head Cap Screw
1
Support Bracket with item 7 1
Roller Bearing Cone
2
Roller Bearing Cup
2
Bearing Cup and Cone
Idler Wheel
1
Internal Retaining Ring
1
Slide Rail
2
Slide Rail Spacer
2
Flat Head Socket Screw
4
Dowel Pin
2
Slide Plate
1
Idler Wheel Shaft
1
Socket Head Cap Screw
8
Bushing
2
Flat Head Screw
2
JARVIS
6206002;;.

ITEM
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PART NO.
1004275
1016243
1055488*
1004154
1006025
1013122
page 6
page 6
1007177
1067008
1010214
1002221
1055361
1029195
1055457
1010579
1032155
1036127
1002224
1055270
1060030
1036103
1055026
1055486
PART NAME
QTY
Washer
2
Idler End Housing
1
Hex Head Screw
6
Plain Washer
6
Door Knob
1
Internal Retaining Ring
1
Torque Knob Assembly
1
Guide Assembly, Idler End
1
Taper Nut
5
Hinge with item 32
1
Hinge Pin
1
Hinge Cover
1
Flat Head Socket Screw
4
Hinge Spacer
1
Socket Hd Shoulder Screw
2
Roll Pin
2
Guide Mounting Plate
1
Bushing (spare part only)
1
Guide Plate Cover
1
Socket Head Cap Screw
2
Hex Head Threaded Insert
1
Torque Knob Thrust Bushing 1
Socket Set Screw, Cup Pt.
1
Hex Head Screw
2
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
parts diagram and list
Model Buster V
page 5 of 16
*
***
DRIVE END
Figure B
**
* Tighten to 37 lbf--ft (50 N--m)
** Tighten to 80 lbf--ft (108.5 N--m)
using wrench 8039120
*** Tighten to 59 lbf--ft (80 N--m)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PART NO.
1055361
1002218
1061229
page 7 or 8
1004051
1055304
1055358
1004093
1013122
1006025
1036422
3063022
1017081
1055482
1004154
1055498*
page 7
1055331
1050232
1036128
1035208
1055367***
1044043
1021424
1002213
1055027
1026090
1026078
1055287
1051001
1061203
PART NAME
QTY
Flat Head Socket Screw
3
Rail Cover, Idler End
1
Saw Frame Rail
1
Top Handle Assembly
1
Internal Lock Washer
1
Hex Head Screw
1
Hex Head Screw
1
Internal Lock Washer
1
Internal Retaining Ring
1
Door Knob
1
Bushing
2
Conduit Assembly
1
Danger Label
1
Pan Head Screw
4
Plain Washer
6
Hex Head Screw
6
Hanger Assembly
1
Hex Head Screw
2
Male Elbow Assembly
1
Locator Bushing
2
O-ring
1
Socket Head Cap Screw
2
Bearing Retaining Flange
1
Ball Bearing
1
Bearing Retaining Cover
1
Socket Head Cap Screw
4
Driven Gear 60 Hz 92 teeth
1
Driven Gear 50 Hz 86 teeth
1
Hex Head Screw
2
Quick Connect Plug
1
External Water Manifold
1
JARVIS
6206002;;.

ITEM
31
32
33
34
PART NO.
1050242
1059030
1055344
1016242
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
1011217
1055049
1004275
1055862
1055499
1061580
1061614
1035210
1058061
1055490
1055485
1010579
1036127
1032155
1002219
1055025
1024063
1055255
page 6
1002209
1057026
1057043
1007173**
1061201
1055277
1032156
1002228
1055296
1004049
1010214
1067007
1055338
1055459
1029187
1035207
56
57
58
59
60
61
62
63
64
65
66
67
68
PART NAME
Male Connector
Plastic Tubing (12 inch)
Hex Head Screw
Drive End Housing with
items 9 and 10
Drain Coupling
Socket Head Cap Screw
Washer
Flat Head Screw
Pan Head Screw
Adjustable Nozzle
Internal Water Manifold
O-ring
Blade Guide
Pan Head Screw
Flat Head Screw
Roll Pin
Bushing (spare part only)
Guide Mounting Plate
Rail Cover, Drive End
Flat Head Socket Screw
Blade Guide Guard
Flat Head Socket Screw
Drive End Guide Package
Guide Plate Cover
Drive End Wheel
Drive End Wheel, Grooved
Bearing Locknut
Door Catch
Flat Head Socket Screw
Nut Cover Plate
Drive Wheel Cover
Hex Head Screw
Split Lock Washer
Hinge Pin
Hinge with item 63
Flat Head Socket Screw
Socket Head Cap Screw
Spacer
Oil Seal
QTY
1
1
1
1
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
1
4
2
2
1
1
1
1
1
3
1
2
1
1
1
3
1
4
1
1
1
1
1
1
1
1
4
4
1
1
5
2
1
1
parts diagrams and list
Model Buster V
ITEM
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
1036103
1013244
1020144
1030067
1021259
1035163
1007041
1006026
1021106
1039024
1002239
1055482
3006005
13
14
15
1006022
1073037
1036124
1036131
1014059
1010213
1010219
1016246
1016247
1061202
1055494
1055502
1058078
1014083
1061231
1058061
1055490
3058057
16
17
18
19
20
21
22
23
24
25
26
3058056
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
1035209
1021139
1055948
1016227
1055104
1004069
1010215
1016244
1016225
1035009
1030096
page 9
1008065
1008077
1008135
1008079
1008376
1008251
1008367
1008294
1055357
1004032
1050771
1035206
1055467
1026089
1026087
1055468
1035214
1021240
1021241
1063163
1035216
1063176
page 6 of 16
PART NAME
Thrust Bushing
Internal Retaining Ring
Torque Knob Shaft
Woodruff Key
Flanged Bearing Race
O-ring
Hex Lock Nut
Torque Knob
Roller Bearing
Ball Plunger
Torque Knob Cover
Pan Head Screw
Torque Knob Assembly
(includes items 1-12)
Lock Pin Knob
Socket Set Screw, Cup Pt.
Drive End Lock Pin Bushing
Idler End Lock Pin Bushing
Compression Spring
Drive End Lock Pin
Idler End Lock Pin
Drive End Guide Housing
Idler End Guide Housing
Guide Plug
Socket Set Screw, Special
Socket Head Cap Screw
Back-up Blade Guide
Compression Spring
Blade Guide Mounting Plate
Blade Guide Insert
Pan Head Slotted Screw
Drive End Guide Package
(includes items 13-26)
Idler End Guide Package
(includes items 13-26)
O-ring
Ball Bearing
Socket Head Cap Screw
Bearing Retaining Flange
Socket Head Cap Screw
Split Lock Washer
Locator Pin
Gear Housing, 60 Hertz
Gear Housing, 50 Hertz
O-ring
Square Key
Motor (3.3 HP):
575V, 60 Hz
460/230V, 60 Hz
380/220V, 50 Hz
42V, 50 Hz
Motor (5 HP):
575V, 60 Hz
460/230V, 60 Hz
380/220V, 50 Hz
42V, 50 Hz
Hex Head Screw
Flat Washer
Hex Socket Pipe Plug
Oil Seal
Socket Set Screw, Cup Pt.
Drive Gear, 60 Hz 28 teeth
Drive Gear, 50 Hz 30 teeth
Socket Set Screw, Flat Pt.
Motor Accessories, Finned:
Gasket Seal
Ball Bearing (Front)
Ball Bearing (Rear)
Rotor
Oil Seal
Electrical Plug
JARVIS
6206002;;.
QTY
1
1
1
1
1
1
1
1
1
8
1
2
2
2
1
1
2
1
1
1
1
2
4
2
2
2
2
4
12
Torque Knob
Assembly
Torque wrench nut adapter 8030054
Torque wrench 8039138
Set to slip at 60--65 lbf--in (6.8--9.9 N--m)
Blade Guide Assembly,
Idler and Drive End
1
1
1
1
3
1
4
4
2
1
1
1
1
Motor and
Gear Cover Assembly
8
8
2
1
1
1
1
1
1

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
parts diagrams and list
Model Buster V
page 7 of 16
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
Hanger Assembly
*
**
* Tighten to 115 lbf--ft
(156 N--m)
** Tighten to 59 lbf--ft
(80 N--m)
Dual Handle
Control Assembly
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Top Handle
Assembly
JARVIS
6206002;;.

PART NO.
1055721
1042125
1021493
1028040
1055469
1055455*
1050243
1016226
1055471
1061855
1028061
1055367**
3061080
1018085
1036132
1019086
1011182
1005020
1005112
1017085
1055487
1002223
1061222
1055090
1011223
1011174
1063148
1011203
1035123
1018086
1010145
3019035
30
31
32
33
34
1055296
1004182
1021314
1010273
1018111
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
1061368
1010275
1014096
1055328
1019118
1042164
1013181
1016316
1039044
1035173
1014098
1005059
1035282
1002270
1055592
1035210
1063220
1001049
1010274
1055358
1042176
1007022
1007059
3019073
PART NAME
QTY
Socket Set Screw, Cup Pt.
2
Hanger Bracket
1
Cylindrical Bearing
2
Pin and Shackle Link Assy.
1
Socket Set Screw, Cup Pt.
1
Socket Hd Shoulder Screw
1
Handle and Plug
1
Bearing Retaining Housing
1
Thumb Screw
1
Cylindrical Insert
2
Hanger Link
1
Socket Head Cap Screw
2
Hanger Assembly
(includes items 1-11)
Right Hand Trigger Lever
1
Bushing (incl. with item 15)
2
Switch Housing and Handle
1
Strain Relief Connector
1
Push Button Switch
2
Safety Kill Switch
1
Electric Danger Label
1
Pan Head Screw
7
Switch Hsg Cover w/ item 19
1
Switch Housing Gasket
1
Button Head Screw
4
Strain Relief Connector
1
Cord Connector, 42V only
Switch Boot
1
Strain Relief Connector
1
Threaded Boot Seal
2
Left Hand Trigger Lever
1
Dowel Pin
2
Saw Handle Assembly
(includes items 13-23
and 25-29)
Hex Head Screw
1
Washer
1
Bushing
1
Threaded Pin
2
Trigger Lever with items 32,
1
35 and 36
Trigger Roller
1
Dowel Pin
1
Compression Spring
1
Hex Head Screw
1
Handle
1
Handle Bracket
1
External Retaining Ring
1
Switch Housing
1
Plunger with item 44
1
O-ring
1
Compression Spring
1
Push Button Switch
1
O-ring
1
Switch Cover
1
Flat Head Phillips Screw
3
O--ring
1
Electrical Connector w/item 50 1
Wire and Plug
1
Threaded Pin
1
Hex Head Screw
1
Handle Bracket
1
Hex Lock Nut
1
Hex Lock Nut
1
Top Handle Assembly
(includes items 30-57)
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
parts diagram and list
Model Buster V
page 8 of 16
ITEM PART NO.
Micro Switch Electric
Handle Assemblies
Top Handle
Assembly
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1055328
1018113
1010273
1014096
1021314
1013181
1042164
3005017
1035282
1002270
1055592
1035210
1063220
1010274
1001049
1055358
1042176
1007022
1007059
1010297
1019128
1004182
1055296
3019115
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
1018085
1036132
1010145
1019086
1011182
1005114
1016354
1035012
1055629
1004423
1013198
1039051
1014119
1013197
1061222
1035507
1002223
1002376
1017085
1055487
1055943
1007242
1042240
1005112
1055090
1011223
1011174
1011203
1063148
1018086
1035123
39
40
41
42
43
44
45
46
47
48
49
50
3019128
3019348
PART NAME
QTY
Hex Head Screw
Trigger Lever with item 5
Threaded Pin
Spring
Bushing
External Retaining Ring
Handle Bracket
Switch Assembly
O--ring
Switch Cover
Flat Head Screw
O--ring
Electrical Connector w/item 12
Threaded Pin
Wire with Molded Plug
Hex Head Screw
Handle Mounting Bracket
Hex Lock Nut
Hex Lock Nut
Roll Pin
Switch Handle with item 20
Washer
Hex Head Screw
Top Handle Assembly
(includes items 1--23)
Right Hand Trigger Lever
Bushing (included with item 27)
Pin
Switch Housing and Handle
Connector, 90 Degree
Switch
Switch Housing with item 31
O--ring
Round Head Screw
Washer
External Retaining Ring
Plunger
Spring
Internal Retaining Ring
Gasket
Gasket, 42V
Housing Cover with item 40
Housing Cover, 42V w/item 40
Danger Label
Pan Head Screw
Hex Head Screw, 42V
Hex Nut
Switch Mounting Bracket
Safety Kill Switch
Button Head Screw
Strain Relief Connector
Strain Relief Connector, 42V
Electrical Connector
Switch Boot
Left Hand Trigger Lever
Trigger Boot Switch
Rear Handle Assy (includes
items 24--45 and 47--50)
Rear Handle Assy, 42V
Rear Handle
Assembly
JARVIS
6206002;;.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
1
1
2
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
2
4
8
2
2
2
2
1
1
1
7
4
1
1
4
1
1
1
1
2
parts diagram and list
Model Buster V
page 9 of 16
Electric Motor with Smooth Housing
For 9 wire and 6 wire motor
hook--ups see page 15
ITEM PART NO.
17
1063783
1063576
1063780
1063778
1063773
1063742
1063779
1063712
1072384
1063893
1072002
1063955
ITEM PART NO.
1
1055321
2
1035216
3
1002342
4
1035456
5
1021240
6
3064001
3064004
7
1013211
8
1021302
9
1035795
10
1014141
11
1016406
1016596
12
1017158
13
1055039
14
1035214
15
1055849
16
1051151
PART NAME
Socket Head Cap Screw
Seal
Motor Cover
O--ring
Ball Bearing
Rotor Assembly, 3.3 HP
Rotor Assembly, 5 HP
Retaining Ring
Ball Bearing
O--ring
Wave Spring
Motor Housing, 3.3 HP
Motor Housing, 5 HP
Information Label
Drive Screw
Gasket
Socket Set Screw
Threaded Fitting
JARVIS
6206002;;.
QTY
6
1
1
1
1
1
3016336
3016337
3016338
3016339
3016340
3016342
3016341
3016343
1
1
1
1
1
3016553
3016572
3016541
3016466
1
4
1
2
2

PART NAME
Stator, 3.3 HP
Stator, 575V--60Hz
Stator, 460/230V--60Hz
Stator, 415V--50Hz
Stator, 380/220V--60Hz
Stator, 380/220V--50Hz
Stator, 115V--50Hz
Stator, 208V--60Hz
Stator, 42V--50Hz
Stator, 5 HP
Stator, 575V--60Hz
Stator, 460/230V--60Hz
Stator, 400/230V--50Hz
Stator, 42V--50Hz
QTY
Stator and Housing Assembly
(includes items 9, 11--13 & 15--17)
3.3 HP
Hsg & Stator 575V--60Hz
Hsg & Stator 460/230V--60Hz
Hsg & Stator 415V--50Hz
Hsg & Stator 380/220V--60Hz
Hsg & Stator 380/220V--50Hz
Hsg & Stator 208V--60Hz
Hsg & Stator 115V--50Hz
Hsg & Stator 42V--50Hz
5 HP
Hsg & Stator 575V--60Hz
Hsg & Stator 460/230V--60Hz
Hsg & Stator 380/220V--50Hz
Hsg & Stator 42V--50Hz
Power Cords (not shown)
3001125 42V, 20 ft
3001121 115--575V, 20 ft
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
1
parts diagrams and lists
Model Buster V
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PART NO.
1017110
1017111
1017085
1063311*
1063312*
1072091
1063862
1063410
1004022
1055010
1063208
1063209
1001014
1011240
1004211
1007278
1032265
1073072
1029445
1004244
1072071
1072072
1016346
3016167
3016190
page 10 of 16
PART NAME
Wiring Diagram, 115V
Wiring Diagram, 220V
Electrical Danger Label
Pigtail Fuse, 115V
Pigtail Fuse, 220V
Glass Fuse, 115V
Glass Fuse, 220V
Ground Lug
Internal Lock Washer
Pan Head Screw
Electrical Outlet
Electrical Plug (not shown)
Electrical Cord
Strain Relief Connector
Sealing Washer
Locking Nut
Panel
Pan Head Slotted Screw
Hex Spacer
Lock Washer
ATD Circuit Board, 115V
ATD Circuit Board, 220V
Electrical Box Enclosure
Electric Control
Box Assembly
QTY
1
1
1
1
1
1
1
1
1
1
1
ft
3
3
3
1
4
4
4
1
1
1
Control Box Assy, 115V
Control Box Assy, 220V
* not used in current tools
4006036
Band Saw with Cold Water Spray
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
JARVIS
6206002;;.

PART NO.
1061616
1055287
1050497
1064521
1016505
1050483
1050488
1061526
1050496
1061525
1061659
1016506
PART NAME
Water Manifold
Hex Head Screw
Tube to Pipe Connector
Plastic Tubing, 12 inch
Drive End Housing
Reducer Fitting
Tee Fitting
Plastic Tubing, 11 inch
Tube Connector Elbow
Spray Tube
Saw Frame Rail
Idler End Housing
QTY
1
2
1
1
1
1
1
1
1
1
1
1
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
parts diagram and list
Model Buster V
page 11 of 16
Control Box Assembly
380V with Starter
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
1016418
1032450
1063496
1063495
1063494
1063522
1063363
1063390
1063825
1063743
1055803
1004247
1072126
1072117
1029445
PART NAME
Electrical Enclosure
Mounting Plate
Yellow/Green Term Block
Blue Terminal Block
Grey Terminal Block
Terminal Rail
Terminal Marker
Fuse Terminal Block
Terminal Marker
Fuse
Pan Head Screw
Internal Lock Washer
Contactor
Overload Relay
Hex Spacer
JARVIS
6206002;;.
QTY
1
1
2
1
5
1
8
1
1
1
3
3
1
1
4

ITEM
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PART NO.
1004244
1073072
1007266
1063862
1011262
1072072
1063502
1007256
1011249
1007249
1011248
1001089
1063208
1017085
1017155
3063179
PART NAME
Internal Lock Washer
Plastic Screw
Locking Nut
Fuse
Strain Relief Connector
ATD Circuit Board, 220V
Terminal Fork
Locking Nut
Strain Relief Connector
Locking Nut
Strain Relief Connector
Electrical Cord, 3 ft
Electrical Plug
Danger Label
Connection Diagram
Control Box Assy, 380V
QTY
4
4
1
2
1
1
9
1
1
2
2
1
1
1
1
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
specifications, installation
and connection diagram
Model Buster V
page 12 of 16
SPECIFICATIONS
ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL, STATE AND LOCAL
ELECTRICAL CODES.
Model Buster V
Motor Power
3.3 hp
2500 W
5 hp
3730 W
Operating Voltage
460/230 V, 3 Phase, 60 Hz
all other voltages and 50 Hz available
Capacity
180 head / hour
Control Handles
Electric Dual Anti-tie Down
Distance between guides 19.75 in
502 mm
Blade Length
127 in
3226 mm
Overall Length
57 in
1448 mm
Drive Wheel Speed
530 rpm
Vibration (less than)
115 dB
0.6 m/sec2
Weight
196 lbs
88.9 kg
INSTALLATION INSTRUCTIONS
ALWAYS DISCONNECT THE POWER SUPPLY
IN ACCORDANCE WITH OSHA’S LOCKOUT/
TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY MAINTENANCE OR
REPAIRS.
1 Install the electrical control box in a dry location that
will not be subject to wash downs.
2 Wire the electrical control box.
Refer to figures 1-- 3.
2.1 Attach wires numbered 1, 2 and 3 to the appropriate AC power supply. Check the label (item 1,
page 10 or item 29, page 11) inside the control
box cover for the correct voltage and frequency.
2.2 Attach wires numbered 4 and 5 to a starter coil
(supplied by the customer). Disconnect any other source of power to the starter coil. The coil operating voltage is indicated on the label (item 1,
page 10 or item 29, page 11) inside the control
box cover.
2.3 The trigger signal connection between the Buster
V and the control box is pre--wired and is approximately 22 feet (6.7 m) long.
3 Wire the motor.
Figure 1
Connection Diagram
380V with Starter
JARVIS
6206002;;.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
installation instructions
Model Buster V
page 13 of 16
Switch in
Top Handle
Red/
White
Stripe
Switches in
Dual Trigger Rear Handle
Red/
Black
Stripe
White
Black
Safety Kill
Switch
Wire Junction
Box on Saw
Green
Electric Circuit Board
White
Green
Black
AC Supply
Starter Coil
2 ft.
Control
Figure 2
Control
Box without Starter
White - Neutral
Black - Hot
Green
Top Handle
To Starter Coil
By Customer
AC Power Supply
3.1 Follow the wiring diagram shown on page 16 for
all dual voltage (6 or 9 wire) motors. All motors
require a power cord with three leads plus an
earth ground.
Rear Handles
20 ft.
3.1.1 Make sure that drive end wheel (item 55,
Figure B, page 5) rotates counterclockwise.
Note: the power supply must be connected to perform the above test only.
4 Install the balancer above the work station on a
trolley.
4.1 The trolley should have sufficient travel to allow
the operator to reach the entire work area. Refer
to figure 4 for dimensions.
Safety
Kill
Switch
5 Suspend the Buster V from the balancer.
5.1 Adjust the balancer to the operators’ preference.
Power from
Starter
6 Adjust the hanger.
Figure 3
Refer to figure 5 for steps 6.1-6.2.
JARVIS
6206002;;.

PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
installation and
operation instructions
Model Buster V
page 14 of 16
7.2 Attach a drain hose (supplied by customer) to the
drain coupling (item 35, Figure B, page 5).
Overall length 57 in. (1.45 m)
Rail thickness 1 in. (25.4 mm)
OPERATION INSTRUCTIONS
ALWAYS DISCONNECT THE POWER SUPPLY
IN ACCORDANCE WITH OSHA’S LOCKOUT/
TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY MAINTENANCE OR
REPAIRS.
12.75 in.
(0.32 m)
19.75 in.
(0.50 m)
Frame Thickness
1.75 in. (44.5 mm)
Figure 4
Adjustment “A”
Safety
Kill
Switch
Water
Hookup
Adjustment “B”
Oil Drain
Water Drain
Figure 5
6.1 Adjustment “A” to adjust the tilt of the saw:
S Move hanger bracket (item 2, page 7) toward
the rear of the Buster V to tip the nose of the
saw down.
S Move the hanger bracket toward the front of
the Buster V to tip the nose of the saw up.
S Tighten socket head cap screws (item 12,
page 7) to 59 lbf--ft (80 N--m).
6.2 Adjustment “B” to adjust the saw to cut straight
down the backbone:
S Turn handle (item 7, page 7) clockwise to cut
more to the right.
S Turn the handle counter-clockwise to cut
more to the left.
7 Attach a cold or warm water hookup.
Refer to figure 5 for steps 7.1-7.2.
7.1 Attach cold or warm water to quick connect plug
(item 29, Figure B, page 5).
JARVIS
6206002;;.

1 Turn on the power.
2 Prior to use or daily, perform the following tests.
2.1 Make sure that the dual anti-tie down control
handles (the top and the rear handles) are working correctly. Depress each trigger separately
and the tool should not start. Depress one trigger,
then pause one second and depress the other trigger and the tool should not start. Repeat this
procedure reversing the triggers. Depress both
triggers simultaneously (within one half second
of each other) and the tool should start. With the
tool running, release one trigger and the tool
should stop. Continue holding the depressed
trigger and then depress the other trigger. The
tool should not start. Repeat this procedure
holding the other trigger. If the tool malfunctions, remove it from service and report the
problem to your supervisor immediately.
2.2 Make sure that the Buster V moves freely on its
balancer.
3 Making the cut.
If an elevating platform is used, the operator can keep
the Buster V in a horizontal position during most of
the split.
Always avoid using pressure; instead, guide the Buster V.
Step 3.1 is necessary only during the operators’
learning period.
3.1 Mark the center of the backbone of the beef with
a knife.
3.2 Start the Buster V.
3.3 Saw through the tail bone using the knife mark as
a guide.
3.3.1 The idler end of the Buster V should be
pointing upward while sawing through the
tail bone.
3.3.2 Do not pressure the Buster V; guide the
Buster V.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
operation and
maintenance instructions
Model Buster V
page 15 of 16
3.4 When the tail bone hits the crossbeam of the
Buster V, saw until the tail bone breaks apart and
the Buster V is allowed to continue its path down
the backbone of the beef.
3.4.1 The drive end of the Buster V should be
lower than the idler end while sawing
through the tail bone.
3.5 After the tail and aitch bones have been split, saw
through the loin area.
3.5.1 The Buster V should be in a horizontal position during this cut.
3.5.2 Do not pressure the Buster V; guide the
Buster V to ensure a straight cut.
3.6 Saw through the shoulder and neck of the beef.
3.6.1 The idler end of the Buster V should be
pointing downward while sawing through
the shoulder and neck.
MAINTENANCE INSTRUCTIONS
blade
torque
guide
knob
blade
guide
tooth direction
grease
fitting
water
manifold
ALWAYS DISCONNECT THE POWER SUPPLY
IN ACCORDANCE WITH OSHA’S LOCKOUT/
TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY REPAIRS OR MAINTENANCE.
1 DAILY:
1.1 The Buster V is equipped with dual anti-tie down
control handles (the top and the rear handles).
Check for the correct operation of the dual antitie down control handles prior to use or daily.
Depress each trigger separately and the tool
should not start. Depress one trigger, then pause
one second and depress the other trigger and the
tool should not start. Repeat this procedure reversing the triggers. Depress both triggers simultaneously (within one half second of each
other) and the tool should start. With the tool running, release one trigger and the tool should
stop. Continue holding the depressed trigger
JARVIS
6206002;;.

and then depress the other trigger. The tool
should not start. Repeat this procedure holding
the other trigger. If the tool malfunctions, repair or remove it from service immediately.
Note: the power supply must be connected to
perform the above operation only.
1.2 Clean and check the blade guide assemblies: Refer to the parts diagram on page 6 for referenced
items unless otherwise noted.
Note: the backup blade guides can be replaced or
rotated without removing the blade guide mounting plate from the saw.
1.2.1 Remove two (2) set screws (item 20).
1.2.2 Slide the blade guide mounting plate (item
24) out of the guide housing (item 18).
1.2.3 Remove six (6) screws (items 26).
1.2.4 Rotate or replace the blade guide inserts
(item 25) as required.
1.2.5 Insert a 0.022 in. (0.56 mm) feeler gage between the blade guide inserts.
1.2.6 Apply a light pressure to the outside of the
blade guides.
1.2.7 Tighten the six (6) screws (item 26).
1.2.8 Remove screw (item 21).
1.2.9 Rotate or replace the back--up blade guide
(item 22) as required.
1.2.10 Tighten the screw (item 21).
1.2.11 Tighten locknut (item 56, Figure B, page 5)
to 80 lbf--ft (108.5 N--m). Jarvis wrench
8039120 is available.
1.3 Check the front bearings:
1.3.1 Grease the front wheel bearings through
grease fitting (item 5, Figure A, page 4) with
food grade wheel bearing grease (NLGI 2).
1.4 Check the oil in the gear housing:
1.4.1 Check the level of oil in the gear housing
(item 34, page 6).
1.4.2 Change the oil if these conditions exist:
• The oil contains water.
• The oil is dark or gritty.
• Any bearing is being replaced.
1.4.2.1 The saw should be tilted rearward and
filled with approximately 1.5 quarts
(1.42 liters) of food grade SAE 85W--90,
ISO 100 or AGMA 3 gear oil.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
maintenance instructions and
motor wiring diagrams
Model Buster V
page 16 of 16
1.5 Check the cord and plug assembly:
1.5.1 Check the cord and plug assembly (items
8-10, page 10) for wear and replace if necessary.
2.1 Clean the torque knob:
2.1.1 Remove the torque knob assembly (item 28,
Figure A, page 4) from the Buster V.
2.1.2 Remove screws (item 12).
2.1.3 Remove cover (item 11).
2.1.4 Turn the torque knob over.
2.1.5 Remove retaining ring (item 2).
2.1.6 Remove shaft (item 3) assembly.
2.1.7 Clean all grease out of the torque knob.
2.1.8 Turn the torque knob so that ball plungers
(item 10) are visible.
2.1.9 Pour oil onto the ball plungers.
2.1.10 Work each ball plunger up and down with a
wooden dowel to lubricate the springs.
2.1.11 Apply Jarvis 1315 White Grease to the ball
plunger surface and to the bearing (item 9).
2.1.12 Install the shaft (item 3).
2.1.13 Rotate the shaft slightly until you can feel
the balls fall into their holes.
2.1.14 Install the retaining ring (item 2).
2.1.15 Tighten the torque knob to 60--65 lbf--in
(6.8--9.9 N--m). Torque wrench nut adapter
8030054 and torque wrench 8039138 are
available.
2.1.16 Install the torque knob cover (item 11).
2.1.17 Install the screws (item 12).
2.1.18 Install the torque knob assembly on the
Buster V.
3 WHEN NECESSARY:
3.1 Replace the blade:
3.1.1 Open wheel covers (item 3, Figure A, page
4 and item 60, Figure B, page 5).
3.1.2 Loosen the torque knob (item 28, Figure A,
page 4) by turning it fully counter-clockwise.
3.1.3 Raise the blade guide assemblies (item 29,
Figure A, page 4 and item 53, Figure B, page
5) so that both guide assemblies are parallel
to the floor.
3.1.4 Install the blade with teeth pointing inward,
toward the frame.
3.1.5 Tighten the torque knob until it “clicks.”
3.1.6 Twist the blade so that the teeth point downward; set the blade guide assemblies down
over the blade.
3.1.7 Close the doors.
3.1.8 Tighten the torque knob after saw has run a
few minutes.
3.2 Tighten the front wheel:
3.2.1 Turn the front bearing locknut (item 6, Figure A, page 4) clockwise until hand tight.
Nine Wire Motor Hook--up
Six Wire Motor Hook--up
Green Screw
Green Wire
Silver Screw
White Wire
Black Screw
Black Wire
Silver Screw
White Wire
Green Screw
Green Wire
Bronze Screw
Black Wire
2 WEEKLY:
Refer to page 6 for referenced items unless otherwise noted.
1017301
JARVIS
6206002;;.

1017296
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457-4926
UNITED STATES OF AMERICA
TEL. 860-347-7271
EMAIL. sales@jarvisproducts.com
FAX. 860-347-6978
WWW.jarvisproducts.com
Download PDF
Similar pages