Before assembly, flush the water supply pipes

FSP8009
GEONA
INSTALLATION GUIDE
Parts List
Please unpack and inspect all packages and components carefully,
make sure they are complete. Examine for shipping damage. If some
parts are damaged or missing, notify your dealer immediately.
For lnstallation Yon may Require
6
Note!
Before assembly, flush the water
supply pipes thoroughly to
remove debris(allow the water to
run with the main stopcock open
for about 3 mins), otherwise dirt
particles might affect the function
of the shower panel!
PAGE 1
©2013 Fresca ™ All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.
Dimensions
Back View
Choose a suitable place to install the shower
panel, adjust the shower panel’s vertical position
based on the user’s height and your sanitary room.
Usually, install the panels at the distance of
82 3/5" from the top to the ground, but you
can assemble according to your instance.
3"
7"
MASSAGE JET
7"
SHOWERHEAD
UPPER HANGING
BRACKET
16 1/4 "
6"
37 1/2 "
LOWER HANGING
BRACKET
63 "
82 3/5"
70 "
5"
48 "
Recommended
height
Cold inlet
Hot inlet
Note! The height can be altered to suit individual
Measure the distance from the upper fixing
hanger to the lower fixing hanger. The
dimensions are for your reference only.
requirements.
The dimensions are for reference only.
PAGE 2
©2013 Fresca ™ All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.
Your item may appear slightly different from the illustration
Note!
Before drilling any holes for fixing your shower panel ensure that
there are no hidden cables or pipework within the wall.
1
2
3
25m
m
6m
m
Dr
ill
wall
Drill the holes in the wall
wall
Insert the wall plugs inside
the holes
wall
Tighten the screws to the wall
with wall mounting brackets
Wall-mounting
Note! Most of “Fresca” shower panels not only can be mounted on the tile,marble
or other flat wall, but also can be mounted against the wall corner.
Hang the shower panel on the mounting bracket
COLD
HOT
PAGE 3
©2013 Fresca ™ All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.
to the “Fresca”outdoors shower panel series.
F95F
0.4
F
86
F113 F10
Note! The shower panel is for indoors use only. For outdoors use please refer
Thermostatic
Control
122
Don’t forget to place the rubber
washer when it is necessary.lt
will avoid water leakage.
head shower
massage jet
massage jet
hand shower
volume controls
thermostatic faucet
1.5m stainless steel hose
massage jet
spout
Technical data
Minimum working pressure 11.6 PSI
Maximum working pressure 72.5 PSI
Recommended operating pressure
21.75 PSI - 43.5 PSI
Test pressure 145 PSI
Temperature scale 86 F-122 F
Hot water temperature Max. 158 F
Safety stop
100.4 F
30 + 10
Operation
86
113
To change the water temperature,
please push the button and turn
knob accordingly.
Select the shower function
100.4
required and adjust the flow-rate
95
by rotating the control knobs.
F
122
The temperature has been pre-settled
at a safe temperature 104 F with the
safety push button to 104 F.
Thermostatic Control
Note! If the safety push button has been operated, it is important that it is returned to its
original position(100.4 F) in order to prevent the next shower user from accidental
scalding if the temperature is too high.
PAGE 4
©2013 Fresca ™ All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.
Thermostatic valve removal and installation
Remove process
1 Take off cap
2 Loosen HEX screw off with allen
3 Take off head
wrench
4 Take off plastic ring
5 Position on the golden ring and pull out 6 Remove the valve
the valve by needle nose pliers
Installation process
1 Place valve in place(ensure
the screw head pointing to
the cut off of the plated ring)
4 Press the button on the head
and put on the head as
below ensuring the screw
hole pointing to the front
2 Put golden ring
3 Put plastic ring in place
on top of valve
with a rubber hammer
(align the red marks in
line)
5 Use allen wrech to fix the
HEX screw tightenly
6 Put on cap
PAGE 5
©2013 Fresca ™ All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.
Download PDF
Similar pages