Form No. 3404-808 Rev A
Transport Wheel Kit
HoverPro® 450/500/550 Machine
Model No. 02622
Operator's Manual
Safety
Vibration
• Before using this kit, refer to the machine Operator’s
Measured vibration level for the left hand = 7.7 m/s2 (model
02602); 3.1 m/s2 (model 02604); 5.8 m/s2 (model 02606).
Manual safety section.
• Do not lift the machine onto the transport wheel kit or
move the machine using the transport wheel kit while
the engine is running.
Measured vibration level for the right hand = 4.8 m/s2 (model
02602); 4.4 m/s2 (model 02604); 4.0 m/s2 (model 02606).
Uncertainty Value (K) = 3.5 m/s2 (model 02602); 2.0 m/s2
(model 02604); 3.0 m/s2 (model 02606).
Setup
1. For models
02602/02603/02604/02606/02609/02610/02611,
with serial number range 314000000–314999999
only:
Drill a 6.4 mm (1/4 inch) diameter hole in the lower
handlebar of the machine (Part No. 111-7260-03), 360
mm (14.17 inch) from the bottom of the handlebar
(Figure 1).
Note: If there is already a hole at this location on the
handlebar, no drilling is required.
Figure 1
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com.
Original Instructions (EN)
Printed in the UK
All Rights Reserved *3404-808* A
Operation
2. Attach the hook to one side of the lower handle bar
using 1 hex bolt, 1 spacer, and 1 nyloc nut. Repeat for
the other side (Figure 2).
Note: When mowing, ensure that the transport wheel kit is
secured to the lower handle bar with both hooks.
Note: Refer to Figure 2 for the correct orientation of
the bolts, spacers, and nuts.
Use the transport wheel kit to safely transport the machine
from one location to another.
3. Slide the axle spacer (300 mm) onto the axle (Figure 2).
4. Place 1 axle spacer (25 mm) and 1 plain washer into
each wheel. Slide the wheels onto the axle.
1. Shut off the engine, then release the hooks from the
lower handlebar, allowing the wheels to touch the
ground.
5. Attach the axle to the undercarriage using 4 washers, 2
hex HD bolts, and 2 nuts.
2. Lower the upper handlebar down far enough for the
deck to clear the ground.
Note: Keep the wheels on the inside of the
undercarriage (Figure 2).
3. Push the machine to the next desired location. To
continue mowing, secure the hooks back up on the
lower handle bar.
6. To transport the machine, lift the unit up and latch the
hooks onto the top crossbar of the lower handle bar.
Maintenance
WARNING
Improper maintenance, using nonconforming
replacement components, or removing or modifying
any component may cause death or serious injury.
Do not modify any components of the kit or replace
any parts.
Ensure that all moving and pivoting parts are sufficiently
lubricated and regularly serviced.
2
2 3
4
1
4
2 3
1
5
7
6
5
9 8
6
12
14
12
11
13
10
13
g018538
8
9
10
Figure 2
1. Hex bolt (2)
5. Nut (2)
2. Hook (2)
6. Washer (2)
9. Axle spacer (25 mm) (2)
10. Wheel (2)
3. Spacer (2)
7. Undercarriage (1)
11. Axle spacer (300 mm) (1)
4. Nyloc nut (2)
8. Plain washer (4)
12. Washer (2)
3
13. Hex HD bolt (2)
14. Axle (1)