Single Pole (One location) or 3-Way (Multi-location

FEATURES
COLLECTION BY LEVITON
• Leviton's Decora® style design
• ON/OFF LED indicates status of load
• Color conversion available
L S
Single Pole (One location) or
3-Way (Multi-location)
120VAC, 60Hz
INSTALLATION INSTRUCTIONS
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES
AND REGULATIONS.
WARNING: IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED
ELECTRICIAN.
WARNING: TO AVOID OVERHEATING AND POSSIBLE DAMAGE TO THIS DEVICE AND OTHER EQUIPMENT,
Quiet Fan Speed Control
Cat. No. MLFØ1-1L, 1.5A (Lighted)
DO NOT INSTALL TO CONTROL A RECEPTACLE, FLUORESCENT LIGHTING, A MOTOR- OR A
TRANSFORMER-OPERATED APPLIANCE OTHER THAN APPROPRIATE CEILING FANS.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, THIS CONTROL IS TO BE USED
WITH CEILING FANS THAT IS MARKED AS SUITABLE FOR USE WITH A SOLID-STATE FAN SPEED CONTROL
AND IS RATED 120 VOLTS AC, TOTAL LOAD 1.5 AMPERES MAXIMUM.
INSTALLATION INSTRUCTIONS
WARNING: FOR USE ON CEILING PADDLE FANS WITH SPLIT-CAPACITOR OR SHADED POLE MOTORS
ONLY. PLEASE REFER TO FAN MANUFACTURER’S INSTRUCTIONS OR RATING LABEL ON THE MOTOR TO
CONFIRM TYPE. USE WITH ANY OTHER TYPES OF MOTORS OR EQUIPMENT MAY CAUSE OVERHEATING
AND/OR DAMAGE TO THE MOTORS OR EQUIPMENT.
OTHER CAUTIONS:
1. DISCONNECT POWER WHEN SERVICING FIXTURE.
2. USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE. WITH ALUMINUM WIRE USE ONLY
DEVICES MARKED CO/ALR OR CU/AL.
MULTI-GANG INSTALLATION:
There is NO derating necessary for multi-gang installations of this Quiet Fan Speed Control.
DI-000-MLF01-00A
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for
the benefit of anyone else that this product at the time of its sale
by Leviton is free of defects in materials and workmanship under
normal and proper use for two years from the purchase date.
Leviton’s only obligation is to correct such defects by repair or
replacement, at its option, if within such two year period the
product is returned prepaid, with proof of purchase date, and a
description of the problem to Leviton Manufacturing Co., Inc.,
Att: Quality Assurance Department, 59-25 Little Neck
Parkway, Little Neck, New York 11362-2591 (In Canada send
to Leviton Mfg. of Canada Ltd., 165 Hymus Blvd., Point Claire,
(Quebec), Canada H9R 1E9). This warranty excludes and there
is disclaimed liability for labor for removal of this product or
reinstallation. This warranty is void if this product is installed
improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under
normal operating conditions or not in accordance with any labels
or instructions. There are no other or implied warranties of any
kind, including merchantability and fitness for a particular purpose,
but if any implied warranty is required by the applicable jurisdiction,
the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to
two years. Leviton is not liable for incidental, indirect, special, or
consequential damages, including without limitation, damage to,
or loss of use of, any equipment, lost sales or profits or delay or
failure to perform this warranty obligation. The remedies provided
herein are the exclusive remedies under this warranty, whether
based on contract, tort or otherwise.
For Technical Assistance Call:
1-800-824-3005 (U.S.A. Only)
1 800 405-5320 (Canada Only)
www.leviton.com
TO INSTALL:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE
AND TEST THAT POWER IS OFF BEFORE WIRING!
2. Remove existing wallplate and switch, if applicable.
3. Remove 3/4” (1.9 cm) of insulation from each circuit conductor. Make sure the ends of wires are straight.
4. Connect wires per appropriate WIRING DIAGRAM as follows: Twist strands of each lead tightly and, with circuit
conductors, push firmly into appropriate wire connector. Screw connectors on clockwise making sure no bare
wires show below the wire connectors. Secure each connector with electrical tape.
5. Installation may now be completed by carefully positioning all wires to provide room in outlet box for control.
Mount control into box with mounting screws supplied. Attach Decora® wallplate.
6. Restore power at circuit breaker or fuse. Check for proper operation of Fan Speed Control by tapping the upper
half of the rocker (refer to Figure 1). The fan will turn
ON at the previous level set. The Fan Speed Level
LED’s will also illuminate at that previous set level
Figure 1 – Fan Speed Functions
(LOW, MEDIUM, or HIGH). The GREEN ON/OFF LED
will turn OFF to indicate power to the Fan Speed
Control (when the dimmer is OFF, the LED is ON).
Mounting Strap
Refer to “OPERATION” section for full details.
Side Sections
7. INSTALLATION IS COMPLETE.
NOTE: On the lower left corner of the switch frame, there
is an air-gap switch. When servicing a controlled fixture,
pull lever out (OFF position). This will cut the power to the
fixture. After servicing is complete, push the lever in (ON
position) to restore power. The lever must be pushed in all
the way (ON position) for normal operation.
Large
Upper
Rocker
Fan Speed
Level Display
Small
Lower
Rocker
Large
Lower
Rocker
Air Gap
Switch
DI-000-MLF01-00A
Small
Upper
Rocker
ON/OFF
LED
COLOR CONVERSION PROCEDURE
Figure 2 – Color Conversion
The color of this device can be changed to suit your
interior design requirements. Simply obtain a color
conversion kit of the appropriate color from your
Leviton distributor and proceed as follows (please note
that wallplate must be removed).
Fan Speed Level Display
Frame
Snaps
Push in 2 Locations
ON/OFF
LED
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using a small
screwdriver, gently remove the frame from the
strap (refer to Figure 2).
Air-Gap
Switch
3. Take the new frame and position it properly to the
strap. Notice that the frame has a cut-out for the airgap switch lever. Line up the plastic snaps with the
square holes in the strap. Insert the snaps on one
side of the frame into the strap.
Strap
Wiring Diagram 1 – Single Location Control Application
4. Firmly press sideways and down to slip the other
snaps into place. The frame snaps in with a audible
click. Ensure that all four snaps are secure.
Replace Decora® wallplate. The color conversion
is complete.
Mural LS
Quiet Fan
Cap with
Wire Connector
Blue
Yellow
TO OPERATE
NOTE: When turning fan ON or increasing speeds, the
Speed Level LED’s will flash indicating that full power
is being momentarily supplied to the fan until selected
fan speed is locked into memory.
White
Hot (Black)
Fan
Line
120VAC, 60Hz
Green
Ground
NOTE: GREEN ON/OFF LED will remain ON when the
fan is OFF facilitating access to switch in the dark.
• ON: Press the large upper rocker.
- Fan will turn ON at previous set level by the small
rockers (speed level LED’s will illuminate at that
set level; LOW, MEDIUM, or HIGH).
White
Neutral (White)
Wiring Diagram 2 – Two Location Control Application
• LOW: Press and hold the small lower rocker or tap
the large lower rocker to select LOW from the HIGH
position.
- Fan will adjust speed to LOW (bottom 2 speed
level LED’s will illuminate).
Remote
MSØØR-1
Mural LS
Quiet Fan
Hot (Black)
• MEDIUM: Press and hold the small upper rocker.
- Fan will adjust speed to MEDIUM (middle 2
speed level LED’s will illuminate).
• HIGH: Press and hold the small upper rocker or
tap the large upper rocker to select HIGH from the
LOW position.
- Fan will adjust speed to HIGH (top 2 speed
level LED’s will illuminate).
Black
Black
Black
Blue
Black
Yellow
Yellow
White
Line
120VAC, 60Hz
Green
Ground
Green
Ground
• OFF: Press the large lower rocker. The speed level
LED’s will remain illuminated for the level set prior
to turning OFF.
Fan
Blue
White
Neutral (White)
Wiring Diagram 3 – Three Location Control Application
SPEED LEVEL DISPLAY:
Indicates the level of fan speed when the fan is ON.
Indicates the previous level of fan speed when the fan is
OFF (refer to Figure 1).
TROUBLESHOOTING
Mural LS
Quiet Fan
Hot (Black)
Black
Yellow
Yellow
Blue
Yellow
Blue
Fan
White
Line
120VAC, 60Hz
Green
Ground
Neutral (White)
DI-000-MLF01-00A
Remote
MSØØR-1
Blue
Black
• Fan does not turn ON and ON/OFF LED does
not turn ON
- Circuit breaker or fuse has tripped.
- Fan has burned out.
- Fan is not connected to line Neutral.
Remote
MSØØR-1
Green
Ground
Green
Ground
White
FOLD SCHEME
8.5¨
Front Panel
LEVITON INSTRUCTION SHEET/MANUAL
SPECIFICATIONS
8.5¨
Cat. No.
DI-000-MLF01-00A
Black
Helvetica
50 Lb. offset
Paper size:
Overall size: 8.5" X 8.5"
Final fold size: 2.83" X 4.25"
DOCUMENTATION
Front Panel
N/A
KKC
11/28/02
Cat. No.
Fold Line
Front Panel
Cat. No.
Panel Line
Download PDF
Similar pages