Important safety instructions
IMPORTANT
When using an electrical machine, basic safety precautions should always be
followed, including the following:
Please read the instruction manual carefully before using this machine.
Keep the instruction manual at a suitable place with the machine and hand it
over if you give the machine to a third party.
When the machine is not in use or left unattended, always disconnect the
machine from the power supply system. Unplug it from the outlet.
DANGER!
To reduce the risk of electric shock:
1. Never leave the machine unattended when it is plugged in.
2. Always unplug this machine from the electric outlet immediately after using
and before cleaning.
3. LED RADIATION: Do not view directly with optical instruments Class.
WARNING!
To reduce the risk of burns, fire, electric shock or injury to persons:
1. The machine mustn't be used by children under 8 or by people with reduced
physical, sensory or mental capabilities or if there is a lack of experience
and knowledge how to operate the machine. Unless they have been given
instruction concerning the use of the machine and the involved risks by a
person who is responsible for their safety.
2. Do not use this machine as a toy. Close attention is necessary when this
machine is used by children, near children or people with reduced
sensation.
3. Use this machine only for its intended use as described in this manual. Use
only accessories recommended by the manufacturer.
4. Children should be supervised to ensure that they do not play with the
machine.
5. Never operate this machine if it has a damaged cord or plug, if it is not
working properly, if it has been dropped or damaged, or dropped into water.
Return the machine to the nearest authorized dealer or service centre for
examination, repair, electrical or mechanical adjustment.
6. Never operate the machine with any air openings blocked. Keep ventilation
openings of the machine and the foot control free from accumulation of lint,
dust, and loose cloth.
7. Keep fingers away from all moving parts. Special care is required around
the machine needle.
8. Always use the proper stitch plate. The wrong plate can cause needle
breakage.
9. Do not use bent needles.
I
Important safety instructions
10. Do not pull or push the fabric while sewing. This can result in needle
breakage.
11. Switch the machine off ("O") when making any adjustments in the needle
area, such as threading or changing the needle, threading the bobbin, or
changing the presser foot, and the like.
12. Always unplug the machine when performing cleaning or maintenance work
such as replacing the sewing light or when making any other user
maintenance adjustments mentioned in the instruction manual (disconnect
the power plug). Cleaning and maintenance work must not be carried out by
children without supervision.
13. Never drop or insert any object into any openings.
14. Use this machine only in dry and protected areas. Never operate the
machine in a damp or wet environment.
15. Do not operate the machine where aerosol spray products are being used
or where oxygen is being administered.
16. To disconnect, turn the power switch to ("O")(off), then remove the plug from
the outlet. Do not unplug by pulling the cord, instead grasp the plug to pull it
from the outlet.
17. If the supply cord of the foot control is damaged, it must be replaced by the
manufacturer or an appropriate service agent or a similar qualified person in
order to avoid endangerment.
18. Never place anything on the foot control.
19. When replacing the light bulb, always use the same type.
20. The machine may only be used in combination with a foot control of the
type C-8001.
21. The sound pressure level during normal operation is lower than 75dB(A).
22. This machine is provided with double insulation (except U.S.A/Canada).
Use only identical replacement parts. See instructions for Servicing of
double-insulated products.
SERVICING OF DOUBLEINSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means is provided on a double-insulated product nor
should a means for grounding be added to the product. Servicing a
doubleinsulated product requires extreme care and knowledge of the system
and should only be done by qualified service personnel. Replacement parts for
a double-insulated product must be identical to those parts in the product. A
double insulated product is marked with the words "DOUBLE INSULATION" or
"DOUBLE INSULATED".
The symbol
may also be marked on the product.
II
Important safety instructions
SAVE THESE INSTRUCTIONS!
Attention!
- This machine is intended for household use only. If used intensively or commercially, regular
cleaning and especially attentive care is required.
- Signs of wear and tear owing to intensive or commercial use are not covered automatically,
even if they occur within the warranty period. The decision on how to deal with any such cases
rests with the local authorised servicing staff.
Note:
If the machine is stored in a cold room, it should be brought to a warm room about one hour
before use.
All rights reserved
For technical and product improvement reasons, the machine's features, parts and accessory
are subject to unannounced changes and alterations at any time. The accessory included can
differ from country to country.
Environmental protection
Ever Sewn is committed to the protection of the environment. We strive to minimize
the environmental impact of our products by continuously improving product Design
and our technology of manufacturing. Do not dispose of electrical machines as
unsorted municipal waste, use separate collection facilities. Contact your local
government for information regarding the collection systems available.
If electrical machines are disposed of in landfills or dumps, hazardous substances can
leak into the groundwater and get into the food chain, damaging your health and wellbeing.
When replacing old machines with new ones, the retailer is legally obligated to take
back your old machine for professional disposal free of charge.
III
Contents
PRINCIPAL PARTS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
TYPE OF PRESSER FOOT CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONNECTING THE MACHINE TO THE POWER SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
START SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Speed adjustment lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Foot control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SEWING TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
USING THE SPOOL NET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
WINDING THE BOBBIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Bobbin winding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
INSERTING THE BOBBIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
THREADING THE UPPER THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
USING THE NEEDLE THREADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
REPLACING THE NEEDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MATCHING NEEDLE/ FABRIC/ THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CHANGING THE PRESSER FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TWO-STEP PRESSER FOOT LIFTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TO RAISE OR DROP THE FEED DOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
UPPER THREAD TENSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
RAISING UP THE LOWER THREAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CUTTING THE THREAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
BUTTONS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19
LCD SCREEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
STITCH CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
OPERATION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Reverse button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auto-lock button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Needle up/ down position button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MEMORY BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Memory button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Clear button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Arrow button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FUNCTION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27
Stitch width adjustment button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Stitch length adjustment button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MODE selection button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mirror button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SELECTION BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Direct stitch selection and number buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
USEFUL SKILLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30
Sewing corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Reverse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Free arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Sewing on heavy fabric. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
STRAIGHT STITCHES AND NEEDLE POSITION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
IV
Contents
ZIGZAG STITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
STRETCH STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
OVERLOCK STITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using the overlock foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using the zigzag foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
BLIND HEM/ LINGERIE STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
BUTTON SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
BUTTONHOLE STITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-39
Making a buttonhole on stretch fabrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
EYELET STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DARNING STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-42
ZIPPER INSERTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-44
Inserting a centered zipper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Inserting a side zipper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
NARROW HEMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
CORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Single cording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Triple cording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
SATIN STITCH SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
GATHERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SMOCKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
FREE MOTION DARNING, EMBROIDERY AND MONOGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . 50-51
Darning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Embroidery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Monogramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
FAGOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
PATCH WORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
QUILTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SCALLOP STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
MIRROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
TWIN NEEDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
WALKING FOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57-59
Combining patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Adding patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Clearing patterns or letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Recalling and sewing the memorized pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-59
WARNING FUNCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Instruction message display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Warning beeping sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-62
Cleaning the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cleaning the sewing machine surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cleaning the hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-62
TROUBLE SHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-64
QUICK ADJUSTMENT REFERENCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-70
V
Principal parts of the machine
Thread tension dial
Bobbin winder spindle
Needle up/down
position button
Speed limiting
adjustment lever
Auto-lock button
Reverse button
Start/stop button
LCD screen
Stitch length
adjustment button
Stitch width
adjustment button
Memory buttons
Thread cutter
Buttonhole lever
Selection buttons
Needle threader
Function buttons
Bobbin cover plate
Sewing table and
accessory box
Bobbin winder stopper
Stitch pattern plate
Horizontal spool pin
Hole for second spool pin
Bobbin thread guide
Upper thread guide
Handle
Handwheel
Presser foot lifter
Main power switch
Power cord
Drop feed lever
Foot controller connector
1
Accessories
1
2
3
Standard
4
1. Zigzag foot
2. Zipper foot
T
I
E
D
3. Buttonhole foot with slide
4. Overlock foot
5. Blindstitch foot
7
6
5
9
8
6. Embroidery foot
7. Button-sew-on foot
A
F
8. Bobbins
H
9. Spool holder (large)
10
11
12
13
14
10. Spool holder (small)
11. Spool pin felt
12. Spool pin long V
13. L Screwdriver
14. Right seam guide
15
16
17
18
15. Brush & seam ripper
16. Needle set
17. Spool net
18. Dust cover
19
20
21
Optional
19. Hemmer foot
P
20. Cording foot
21. Quilting foot
22
23
22. Darning / Embroidery foot
24
23. Gathering foot
24. Walking foot
25. Twin needle
25
Note:
- Accessories are stored inside the accessory box.
- Optional accessories are not supplied with this machine; they are however available as special
accessories from your local dealer.
2
Type of presser foot chart
PRESSER FOOT
T
Zigzag foot
APPLICATION
NEEDLE PRESSER FOOT
General sewing,
Patchwork stitches,
Decorative
stitching,
Smocking,
Fagoting, etc.
APPLICATION
Cording
Cording foot
(Optional)
Inserting zippers
Narrow hemming
I
Zipper foot
Hemmer foot
(Optional)
Buttonhole sewing,
Bar tack stitches,
Darning stitches.
D
Darning
Free embroidery
Monogramming
Darning/
Embroidery foot
(Optional)
Buttonhole foot
with slide
Button sewing
Quilting
P
Quilting foot
(Optional)
Button-sew-on foot
Blind hem stitching
Gathering
F
Blindstitch foot
Gathering foot
(Optional)
This foot helps to
prevent uneven
feeding of very
difficult fabrics
Overlocking
E
Overlock foot
Satin stitch sewing
Walking foot
(Optional)
A
Embroidery foot
3
NEEDLE
Connecting the machine to the power source
Caution:
Always make sure that the machine is unplugged from power source and the main switch is on
("O"). when the machine is not in use and before inserting or removing parts.
ON
OFF
Connecting the machine
Before connecting the power supply, make sure that the voltage and frequency shown on the
machine is conforming with your electrical power.
Place the machine on a stable table.
1. Connect the power line cord to the machine by inserting the 2-hole plug into the terminal box.
2. Connect the power line plug to the electric outlet.
3. Turn on the power switch.
4. The sewing lamp will light up when the switch is turned on.
5. After switching off, it will take some time to consume the residual power in the circuitry. The
light does not turn off immediately after switching off the power. This is a normal phenomenon
for an energy efficient appliance.
To disconnect, turn the power switch to the off position, then remove plug from outlet.
Polarized plug information
This appliance has a polarized plug (one blade wider than the other),
to reduce the risk of electrical shock; this plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Do not
modify the plug in any way.
4
Start sewing
Start/stop button
The machine will start running when
Start/stop button is pressed and will stop
when pressed the second time.
The machine will rotate slowly at the
beginning of the sewing.
Speed adjustment lever
The speed limiting adjustment lever can
control the sewing speed. To increase the
speed, slide the lever to the right. To
decrease the sewing speed, slide the lever
to the left.
Foot control
With the sewing machine turned off, insert
the foot control plug into its connector on the
sewing machine.
Turn on the sewing machine, and then
slowly depress the foot control to start
sewing.
Release the foot control to stop the sewing
machine.
Attention:
Consult a qualified electrician if in doubt as how to connect the machine to the power source.
Unplug the power cord when the machine is not in use.
5
Sewing table
Keep the sewing table horizontal, and pull it in
the direction of the arrow.
The inside of the sewing table is used as an
accessory box.
Using the spool net
When using special threads which wind quickly
off the thread spool, attach a net to the spool
before using.
Spool net
* If the net is too long, cut the net to match the
size of the spool.
Thread
Spool holder
Spool pin
6
Winding the bobbin
1
2
3
4
10
Bobbin winding
1
Place the thread and spool holder onto the spool pin.
For smaller spools of thread, place spool holder with
the small side next to the spool or use the small spool
holder.
2
Snap the thread into the thread guide.
3
Wind the thread contrary clockwise around the bobbin
winder tension discs.
4
Place the thread end through one of the inner holes in
the bobbin as illustrated and place empty bobbin on the
spindle.
5
Push the bobbin to right.
1
2
2
3
4
5
7
Winding the bobbin
6 When the bobbin winder shaft is pushed to the right,
The LCD will display the figure "
".
6
7 Hold the thread tail securely in one hand.
7
8 Press on the foot control or the Start/stop button to start
winding the bobbin.
8
9 After the bobbin has wound a few turns stop the
machine and cut the thread near the hole of the bobbin.
Continue filling the bobbin until it is full. Once the spool
is full, it rotates slowly. Release the pedal or stop the
machine. Push the bobbin winder spindle to left.
9
10 Cut the thread and then remove the bobbin.
10
Please Note:
When the bobbin winder switch is placed on the right, "bobbin winding position", the machine will
not sew and the handwheel will not turn. To start sewing, push the bobbin winder switch to the left
"sewing position".
8
Inserting the bobbin
Attention:
Turn power switch to off ("O") before inserting
or removing the bobbin.
When inserting or removing the bobbin,
the needle must be fully raised.
Open the bobbin cover plate.
Insert the bobbin in the bobbin case with the
thread running in a counterclockwise
direction (arrow).
Pull the thread through the slit (A).
A
With a finger held gently on top of the
bobbin.
Draw the thread at the arrow markings into
the stitch plate thread guide from (A) to (B).
B
A
Pull the thread at the arrow markings into
the stitch plate thread guide from (B) to (C).
To cut off excess thread pull thread back
over the cutting off blade at point (C).
Close the bobbin cover plate.
B
C
9
Threading the upper thread
2
3
1
4
6
5
7
8
Please Note:
It is important to carry out the threading correctly as by not
doing so, several sewing problems could result.
Start by raising the needle to its highest position, and
also raise the presser foot to release the tension discs.
1 Lift up the spool pin. Place the spool of thread on the spool
pin so that the thread comes from the left side of the spool,
then place the spool cap at the end of the spool pin.
1
Note:
In order to prevent tangling of the thread, please use a spool
net. The net is especially usefull to work from large or loose
wound spools.
10
Threading the upper thread
2 Draw the thread from the spool through the upper thread
guide.
2
2
3 Guide the thread around the thread guide pulling the
thread through the pre-tension spring as illustrated.
3
4 Thread the tension module by passing the thread
between the silver discs.
4
5 Then, down and around the check spring holder.
5
6 At the top of this movement, pass the thread from right to
the left through the slotted eye of the take-up lever and
then downwards again.
6
7 Pass the thread behind the flat, horizontal thread guide.
Guide the thread through the wire loop.
8 Pull the end of the thread through the needle from front
to rear, and pull out about 10 cm of thread.
You could use the needle threader to thread the needle.
(On the next page.)
7
8
11
Using the needle threader
Attention:
Turn power switch to the off position ("O").
Raise the needle to its highest position
and lower the presser foot.
1 Lower the needle threader lever slowly and
draw the thread through the thread guide as
illustrated and then to the right.
1
2 The needle threader automatically turns to
the threading position and the hook pin
passes through the needle eye.
2
3 Take the thread in front of the needle.
3
4 Hold the thread loosely and release the
lever slowly. The hook will turn and pass the
thread through the needle eye forming a
loop.
Pull the thread through the needle eye.
When using thin needles the needle
threader might not be applicable.
4
12
Replacing the needle
Attention:
Turn power switch to off ("O") when carrying
out any of the above operations!
B
Change the needle regularly, especially if it is
showing signs of wear and causing problems.
Insert the needle following the illustrated
instructions.
A
A. Loosen the needle clamp screw and
tighten again after inserting the new
needle. The flat side of the shaft should be
towards the back.
B. Insert the needle as far up as it will go.
Needles must be in perfect condition.
Problems can occur with:
- Bent needles
- Blunt needles
- Damaged points
Matching needle/ fabric/ thread
NEEDLE, FABRIC, THREAD SELECTION GUIDE
NEEDLE SIZE
FABRICS
THREAD
9-11 (70-80)
Lightweight fabrics-thin cottons, voile,
serge, silk, muslin, Qiana, interlocks,
cotton knits, tricot, jerseys, crepes, woven
polyester, shirt & blouse fabrics.
Light-duty thread in cotton, nylon,
polyester or cotton wrapped
polyester.
11-14 (80-90)
Medium weight fabrics-cotton, satin,
sailcloth, double knits, lightweight
woollens.
14 (90)
Medium weight fabrics-cotton duck,
woolen, heavier knits, terrycloth, denims.
16 (100)
Heavyweight fabrics-canvas, woolens,
outdoor tent and quilted fabrics, denims,
upholstery material (light to medium).
Most threads sold are medium
size and suitable for these
fabrics and needle sizes.
Use polyester threads on synthetic
materials and cotton on natural
woven fabrics for best results.
Always use the same thread on
top and bottom.
18 (110)
Heavy woollens, overcoat fabrics,
upholstery fabrics, some leathers and
vinyls.
Heavy duty thread, carpet thread.
Please Note:
- In general, fine threads and needles are used for sewing fine fabrics, and thicker threads are used
for sewing heavy fabrics.
- Always test thread and needle size on a small piece of fabric, which will be used for actual sewing
project.
- Use the same thread for needle and bobbin.
- Use a stabilizer for fine or stretchy fabrics.
13
Changing the presser foot
Attention:
Turn power switch to off ("O") when carrying out any of the below
operations!
Removing the presser foot
Raise the presser foot.
Press the black lever (e) and the foot will disengages.
e
Attaching the presser foot
Lower the presser foot holder (b) until the cut-out (c) is directly
above the pin (d).
Press the black lever (e).
Lower the presser foot holder (b) and the presser foot (f) will
engage automatically.
e
c
d
d
f
Removing and attaching the presser foot holder
Raise the presser foot bar (a).
Remove and attach the presser foot holder (b) as illustrated.
a
b
g
Attaching the right seam guide
Attach the right seam guide (g) in the slot as illustrated. Adjust
according to need for hems, pleats, etc.
14
Two-step presser foot lifter
The presser foot lifter raises and lowers your
presser foot.
When sewing several layers or thick fabrics,
the presser foot can be raised a second
stage for easy positioning of the work.
Note:
The needle must always be at the highest
position.
To raise or drop the feed dog
With the sewing table off the machine, the
feed dog adjustment lever can be seen on
the base at the rear side of the sewing
machine.
Sliding the lever to "
" (b) will lower the
feed dog, for example during button sewing or
monogramming. If you wish to continue sewing
normally, slide the lever to "
" (a) in order
to raise the feed dog.
The feed dog will not rise up if you do not turn
the handwheel, even if the lever is slid to
position (a) make a complete turn of the
handwheel to raise the feed dog.
a
b
b
a
15
Upper thread tension
- Basic thread tension setting is: "4"
- To increase the tension, turn the dial to the next number
up. To reduce the tension, turn the dial to the next
number down.
- Proper setting of tension is important to good sewing.
- For all decorative sewing you will always obtain a nicer
stitch and less fabric puckering when the upper thread
appears on the bottom side of your fabric.
Surface
Normal thread tension for straight stitch sewing.
Upper thread
Reverse side
Bobbin thread
Thread tension is too loose for straight stitch sewing. Turn
dial to higher number.
Thread tension is too tight for straight stitch sewing. Turn
dial to lower number.
Normal thread tension for zig zag and decorative sewing.
16
Raising up the lower thread
1 Hold the upper thread with the left hand.
Turn the handwheel towards you
(counterclockwise) lowering, then raising
the needle.
1
2 Gently pull on the upper thread to bring
the bobbin thread up through the stitch
plate hole. The bobbin thread will come
up in a loop.
2
3 Pull both threads to the back under the
presser foot.
3
Cutting the thread
Raise the presser foot.
Remove the fabric, draw the threads to the
left side of the face cover and cut using the
thread cutter.
The threads are cut at the proper length to
start the next seam.
17
Buttons of the machine
5
4
3
10
9
6
7
8
2
1
13
12
11
Operation buttons (see page 22/23)
1.Start/stop button
Press this button to start or stop the machine.
2. Reverse button
Hold down this button to sew either backwards or a reinforcement stitch at a low speed.
3. Auto-lock button
Hold down this button to sew locking stitches immediately or at the end of the current patterns
and automatically stop.
4. Needle up/down position button
Press this button to move the needle either up or down.
5. Speed limiting adjustment lever
Slide this lever to change the sewing speed.
18
Buttons of the machine
Memory buttons (see page 24)
6. Memory button
Press this button to enter or store the created pattern combination in the memory.
7. Arrow button
Press the "
" button or "
" button until the actual stitch number is displayed.
8. Clear button
If an incorrect stitch is selected or memorized, pressing this button will clear it.
Function buttons (see page 25/26/27)
9. Stitch length adjustment button
Press this button to adjust the length of the stitch.
10. Stitch width adjustment button
Press this button to adjust the width of the stitch.
11. Mode selection button
Press this button to select direct mode, utility and decorative pattern mode or block letter mode.
12.Mirror button
Press this button to sew a reflection pattern.
Selection buttons (see page 28)
13.Direct stitch selection and number buttons
Instant access to direct stitches or press number buttons of the stitch number to select the
desired stitch.
19
LCD screen
Direct Pattern
Mirror
Needle up
Auto-lock
Buttonhole lever
Bobbin winding
Reverse
Needle position
Pattern number
Stitch width
Direct mode
Pattern
Needle down
Mirror
Auto-stop
Reverse
Stitch number
Stitch width
MEM
Normal mode
Suggested presser foot
Number of current units
Total number of units
Memory
Stitch length
Alphabet
Needle up
Auto-stop
Stitch number
Stitch width
MEM
Suggested presser foot
Alphabet mode
20
Number of current units
Total number of units
Memory
Stitch chart
The portions marked in gray (on the chart below) show the single unit of each stitch.
A. Direction Patterns
1
2
3
4
5
6
7
8
9
0
B. Patterns
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74
75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
C. Alphabets
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62
63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
89 90 91 92 93 94 95 96 97
21
Operation buttons
Needle up/down
position button
Reverse button
Auto-lock button
Start/stop button
Start/stop button
The machine will start running when Start/stop
button is pressed and will stop when pressed the
second time. The machine will rotate slowly at the
beginning of the sewing.
The sewing speed can be controlled by the speed
limiting adjustment lever.
This way you may operate the machine without
foot control.
Reverse button
Direct
Patterns
When the Direct Stitches 1-5 and Stitches 00-05
are selected.
Reverse is pressed to sew in reverse. An arrow
" " will be shown in the LCD when the function
is active. If you press and hold the Reverse button
the machine will sew backwards until you release
the button.
The longest reverse stitch length is 3 mm.
Press the reverse button when the Direct Stitches
6-7 and Stitches 06-14, 25-99 are selected, the
machine will sew a reinforcement stitch at a low
speed if the Reverse button is pressed.
22
Operation buttons
Auto-lock button
When the Direct Stitches 1-7 and Stitches 00-14
are selected, the machine will immediately sew 3
locking stitches when the Auto-lock button is
pressed, then automatically stop.
The LCD will display the figure "
" until the
machine is stopped.
Please Note:
When the Direct Stitches 25-99 are selected,
press the Auto-lock button, the machine will sew
3 locking stitches at the end of the current pattern
and automatically stop.
Needle up/ down position button
With the Needle up/ down position button, you
decide whether the needle shall stop in the
highest position or in the material when you stop
sewing.
Please Note:
During sewing, the function of the button will not
be activated.
Press the button so that the arrow, on the LCD
screen, will point upward "
" and the needle will
stop in the highest position. When you press the
button so that the arrow points downward "
",
the machine will stop with the needle in the lowest
position.
23
Memory buttons
Clear button
Arrow button
Memory button
MEM
Memory button
Press the "
" button to enter the memory mode,
and store the combinations of characters or
decorative stitches. Press the " " button again to
leave the memory mode and return to Direct mode.
Please Note:
The Direct mode stitches and buttonholes cannot
be memorized.
Clear button
Press this button when the incorrect character is
selected. Each press of this button erases one
character, or press this button to remove an
added stitch when sewing combinations of
characters or decorative stitches.
Arrow button
Use the arrow "
" or "
" button to confirm the
pattern memorized by pressing this button in
memory mode.
24
Function buttons
Stitch width
adjustment button
Stitch length
adjustment button
Mirror button
Mode selection button
Stitch width adjustment button
When you select a stitch, the machine will automatically set the recommended stitch width, which
will be indicated by numbers on the LCD screen.
The stitch width can be regulated by pressing the
stitch width adjustment buttons.
Certain stitches have a limited stitch width.
For a narrower stitch, press the " " button (left).
For a wider stitch, press the " " button (right).
The stitch width can be adjusted between "0.07.0". Certain stitches have a limited stitch width.
When stitches 00-04 are selected, the needle
position is regulated by the stitch width adjustment
buttons. Pressing the " " button (left), will move
the needle to the left and pressing the " " button
(right), will move the needle to the right.
The numbers will be changed from left position
"0.0" to extreme right position "7.0". The pre-set
center needle position will be indicated as "3.5".
25
Function buttons
Stitch length adjustment button
When you select a stitch the machine will
automatically set the recommended stitch length
which will be indicated by numbers on the LCD
screen. The stitch length can be adjusted by
pressing the stitch length adjustment buttons.
To shorten the stitch length, press the " " button
(left). For a longer stitch length, press the " "
button (right).
The stitch length can be adjusted between "0.04.5". Certain stitches have a limited length.
MODE selection button
When you turn the machine "ON" the LCD screen
display will be set at direct mode "
".
Press the "
" button to "
" mode, if you
press the function button again, "
" will be
displayed. After a third press, "
" is displayed
again.
Direct mode stitch selection.
Utility and decorative pattern mode: Stitch
selection using number buttons.
Block letter mode: Character selection
using number buttons.
26
Function buttons
Mirror button (see page 54)
The stitches 00-14, 25-99 can be mirrored,
pressing the "
" button will sew a reflection
pattern from your selected stitch.
The LCD will display the mirror function and the
machine will continue to sew the reflected pattern
until the mirror function is pressed again to cancel
the mirror function.
When the mirror function disappears from the
LCD screen, the machine will continue to sew the
normal stitch.
If you change the stitch setting, then the mirror
function will be cancelled accordingly. If you need
the reflection pattern, then press the mirror button
again.
27
Selection buttons
Direct stitch selection
and number buttons
Direct stitch selection and number buttons
Direct pattern selection
Press the buttons to select the utility patterns
shown beside the number button when the mode
button is set at the Direct mode.
Number buttons
Press the number buttons for selecting the
pattern needed.
Except the Direct stitch mode, the other mode
can be selected by pressing the desired numbers.
For example: stitch no. 32
28
Useful skills
3
1
4
2
Sewing corners
1. Stop the sewing machine when you reach
a corner.
2. Lower the needle into the fabric manually
or by pressing the needle up/ down button
5
once.
3. Raise the presser foot.
4. Use the needle as a pivot and turn the
fabric.
5. Lower the presser foot and resume
sewing.
Reverse
Reverse stitching is used to secure the
threads at the beginning and at the end of a
seam.
Press the reverse button and sew 4-5
stitches.
The machine will sew forward when the
button is released.
Free arm
Free-arm sewing is convenient for sewing
tubular fabrics such as pant hems and cuffs.
29
Useful skills
Sewing on heavy fabric
The black button on the left side of the
presser foot T will lock the presser foot in a
horizontal position if you push it in and hold
it while lowering the presser foot. This
ensures even feeding at the beginning of a
seam and helps when sewing multiple layers
of fabric such as sewing over higher seams
when hemming jeans.
When you reach the point of an increased
thickness, lower the needle and raise the
presser foot. Press the toe of the foot and
push in the black button, then lower the foot
and continue sewing.
The black button releases automatically
after sewing few stitches.
You can also place another piece of fabric
with the same thickness at the back of the
seam or support the presser foot while
feeding by hand and sewing toward the
folded side.
Cardboard or
thick fabric
30
Straight stitches and needle position
00
01
02
03
04
T
Changing the needle position
These setting apply only to stitches 00-04. The pre-set
position is "3.5", center position. When you press the " "
stitch width adjustment button, the needle position will
move to the left. When you press the " " stitch width
adjustment button, the needle position will move to the right.
0.0
0.5
2.0
1.0
3.5
5.0
3.0
2.0
7.0
4.5
Changing the stitch length
To shorten the stitch length, press the " " stitch length
adjustment button. For a longer stitch length, press the " "
stitch length adjustment button.
Generally speaking, the thicker the fabric, thread and
needle, the longer the stitch should be.
Zigzag stitches
05
06
07
07
A
T
Adjusting the stitch width
The maximum zigzag stitch width for zigzag stitching is
"7.0"; however, the width can be reduced on any stitches.
The width increases as you press the " " stitch width
adjustment button from "0.0-7.0".
0.0
1.0
3.0
5.0
7.0
Adjusting the stitch length
The density of zigzag stitches increase as the setting of
stitch length approaches "0.3".
Neat zigzag stitches are usually achieved at "1.0-2.5".
Closed up zigzag stitches (close together) are referred to
as a satin stitch.
0.5
1.0
2.0
3.0
4.5
31
Stretch stitch
02
03
07
07
T
A
Straight stretch stitch
Use these stitches with knitted, tricot or other
stretchy fabrics. The stitch enables your seam
to stretch without breaking the thread.
It assures a stitch that is strong and flexible.
It can also be used to ravel and knit fabrics.
It is also good for joining durable fabric such
as denims.
These stitches can also be used as a
decorative top stitch.
Straight stitch
02
Straight stretch stitch is used to add triple
reinforcement to stretch and hardwearing
seams.
03
Triple zigzag stretch stitch is suitable for firm
fabrics like denim, poplin, duck, etc.
07
32
Overlock stitches
Sew overlock stitches along the edge of fabric to prevent them from fraying.
05
Using the overlock foot
08
E
5.0~7.0
2.0~3.0
Change the presser foot to the overlock foot
(E).
Sew the fabric with the fabric edge against
the guide of the overlock foot.
Attention:
The overlock foot should be used to sew
with stitches 05 and 08 only and do not set
the stitch width narrower than "5.0". It is
possible that needle could hit the presser
foot and break when sewing other stitches
and width.
06
Using the zigzag foot
09
T
2.5~4.5
2.0~3.0
Change the presser foot to the zigzag foot (T) .
Sew overlock stitches along the edge of the
fabric so that the needle drops over the edge
of the fabric on the right side.
33
Blind hem/ Lingerie stitch
Secure the bottoms of skirts and pants with a blind hem, this stitch will sew without showing
stitches on the right side of fabric.
10
10: Blind hem/lingerie for firm fabrics
11: Blind hem for stretch fabrics
11
2.5~4.0
F
1.0~2.0
5mm
Reverse Overcasting
side
stitches
5mm
Please Note:
It takes practice to sew blind hems. Always
make a sewing test first.
Fold the fabric as illustrated with the reverse
side uppermost.
First carry out an overcasting stitch as
shown in left picture. Then fold as shown in
the right picture.
Reverse
side
a
Place the fabric under the foot. Turn the
handwheel forward by hand until the needle
swings fully to the left. It should just pierce
the fold of the fabric. If it does not, adjust the
stitch width accordingly.
Adjust the guide (b) by turning the knob (a)
so that the guide just rests against the fold.
b
Sew slowly, guiding the fabric carefully along
the edge of the guide.
Turn over the fabric.
Right
side
Reverse
side
34
Button sewing
05
2.5~4.5
Change the presser foot to the button-sew-on
foot.
a
Move the drop feed control to "
lower the feed dog.
" to
b
b
a
Position the work under the foot. Place the
button in the desired position, lower the foot.
05
2.5~4.5
Select zig zag pattern. Adjust the stitch width
to "2.5-4.5" according to the distance
between the two holes of the button.
Turn the handwheel to check that the needle
goes cleanly into the left and right holes of
the button.
If a shank is required, place a darning needle
on top of the button and sew.
Pull end of the upper thread to the reverse
side of the fabric, then tie it with the bobbin
thread.
For buttons with 4 holes, sew through the
front two holes first, push work forward and
then sew through the back two holes.
Please Note:
When you finish the work, move the drop feed
control to "
" to raise the feed dog.
35
Buttonhole stitching
Buttonhole sewing to match the size of the button is possible.
For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better buttonhole
finish.
15: For thin or medium fabric
15
2.5~7.0
D
16
18
0.3~1.0
16: For horizontal holes on blouses or shirts
made from thin or medium fabric
17: For suits or overcoats
19
2.5~5.5
0.3~1.0
18: For horizontal buttonholes on thick fabrics
19: For thin or medium fabric
17
5.5~7.0
0.3~1.0
20: For jeans or stretch fabric with a coarse
weave
21: For stretch fabric
20
3.0~7.0
1.0~2.0
21
3.0~7.0
1.0~3.0
Please Note:
Before sewing a buttonhole on your project,
practice on a test piece of the same type of
fabric.
Mark the positions of the buttonhole on the
fabric.
The maximum buttonhole length is 3cm (1
3/16 inch). (Total of diameter + thickness of
button.)
Attach the buttonhole foot, then pull out the
button holder plate and insert the button.
The size of the buttonhole is determined by
the button inserted in the button plate.
The thread should be passed through the
hole in the presser foot, then be placed
under the foot.
36
Buttonhole stitching
Select the buttonhole stitch.
Adjust the stitch width and the stitch length to
the desired width and density.
Position the fabric under the presser foot
with the front end of the buttonhole mark
aligned with the center line on the buttonhole
foot.
Starting
point
Pull the buttonhole lever all the way down
and position it behind the bracket on the
buttonhole foot.
Please Note:
When you select any buttonhole pattern,
LCD screen will be demonstrated the figure
"000", it is to remind you to lower the
buttonhole lever.
Slightly hold the end of the upper thread and
start sewing.
Please Note:
Gently feed the fabric by hand.
Before stopping, the machine will automatically
sew a reinforcement stitch after the buttonhole
is sewn.
37
Buttonhole stitching
* Buttonholes are sewn from the front of the presser foot to the back, as shown.
15
16
18
19
17
20
21
Raise the presser foot and cut the thread. To
sew over the same buttonhole, raise the
presser foot (it will return to its original
position).
After sewing the buttonhole stitch, raise the
buttonhole lever until it stops.
Cut the center of the buttonhole being
careful not to cut any stitches on either side.
Use a pin as a stopper at the bar tack so you
do not cut too much.
Please Note:
When cutting the buttonhole with the seam
ripper, do not place your hands in the cutting
direction, otherwise injuries may result.
38
Making a buttonhole on stretch fabrics
When sewing buttonholes on stretch fabric,
hook heavy thread or cord under the buttonhole foot.
Attach the buttonhole foot and hook the gimp
thread onto the back of the presser foot.
Bring the two gimp thread ends to the front of
the foot and insert them into the grooves,
then temporarily tie them there. Lower the
presser foot and start sewing.
Set the stitch width to match the diameter of
the gimp thread.
Once sewing is completed, pull the gimp
thread gently to remove any slack, then trim
off any excess.
Please Note:
It is suggested that you use interfacing on
the backside of the fabric.
39
Eyelet Stitch
Eyelet stitches are used for making belt holes and other similar applications.
22: Select for sewing eyelets on belts, etc
22
A
5.0 6.0 7.0
Select stitch no. 22 to get the eyelet stitch.
Attach embroidery foot (A).
A
B
Press " " or " " of the stitch width adjustment
buttons to select the eyelet size.
Size of eyelet.
A. Small: 5.0mm (3/16 inch).
B. Medium: 6.0mm (15/64 inch).
C. Large: 7.0mm (1/4 inch).
C
Lower the needle into the fabric at the
beginning of the stitching, and then lower the
presser foot lever.
Once sewing is completed, the machine
automatically sews reinforcement stitches,
then stops.
Make a hole at the center using an eyelet
punch.
* Eyelet punch is not included with the
machine.
Please Note:
- When using the eyelet punch, place thick
paper or some other protective sheet under
the fabric before punching the hole in the
fabric.
- If thin thread is used, the stitching may be
coarse. If this occurs, sew the eyelet twice
one on top of the other.
40
Darning stitch
Darning a small hole or a tear before it becomes larger can save a garment. Choose a fine
thread in a color as close as possible to your garment.
23
3.5~7.0
D
1.0~2.0
Select stitch no. 23 to get the darning stitch.
Change the presser foot to the buttonhole
foot.
Baste the upper fabric and the under fabric
together. Select the needle position. Lower
the presser foot over the center of the tear.
Pull the button holder to rear.
Set the button guide plate on buttonhole foot
to the desired length.
The size of one darn cycle is variable.
However, the maximum stitch length is 2.6
cm (1 inch) and the maximum stitch width is
7 mm (9/32 inch).
Stop
a. The length of sewing.
b. The width of sewing.
Start
41
Darning stitch
Position the fabric so that the needle is 2mm
(1/16 inch) in front of the area to be darned,
then lower the presser foot lever.
Please Note:
When lowering the presser foot, do not push
in the front of the presser foot, otherwise the
darning will not be sewn with the correct size.
2mm
Pass the upper thread down through the
hole in the presser foot.
Pull down the buttonhole lever. The
buttonhole lever is positioned behind the
bracket on the buttonhole foot.
Gently hold the end of the upper thread in
your left hand, and then start sewing.
Darning stitches are sewn from the front of
the presser foot to the back, as shown.
23
Please Note:
If the fabric does not feed, for example,
because it is too thick, increase the stitch
length.
If the sewing range is too big to sew, then
we suggest you can sew several times (or
cross sew) to get a better sewing result.
42
Zipper insertion
This foot can be set to sew on each side of the zipper, the edge of the foot guides the zipper
to ensure straight placement.
Attention:
Zipper foot should be used for sewing straight
stitch with center needle position only. It is
possible that needle could hit the presser foot
and break when sewing other patterns.
00
3.5
I
1.5~3.0
Inserting a centered zipper
5mm
- Place the right sides of the fabric together.
Sew a bottom seam in the width of seam
allowance from the right edge to the zipper
bottom stop position. Sew a few stitches in
reverse to lock. Increase the stitch length to
maximum, set the tension below 2, and
baste the remaining length of the fabric.
Reverse
stitches
Basting
stitching
- Press open the seam allowance.
Place the zipper face down on the seam
allowance with the teeth against the seam
line. Baste the zipper tape.
Reverse
side
2cm
- Attach the zipper foot. Attach the right side
of the presser foot pin to the holder when
sewing the left side of the zipper.
- Attach the left side of the presser foot pin
to the presser foot holder when sewing the
right side of the zipper.
- Stitching around the zipper.
Please Note:
When sewing, be sure that the needle does
not touch the zipper, otherwise the needle
may bend or break.
- Remove the basting and press.
43
Zipper insertion
Inserting a side zipper
5mm
- Baste the zipper opening on the garment.
Place the right sides of the fabric together.
Sew a bottom seam the width of seam
allowance from the right edge to the
zipper bottom stop position. Sew a few
stitches in reverse to lock. Increase the
stitch length to maximum, set the tension
below 2, and baste the remaining length
of the fabric.
Reverse
stitches
Basting
stitching
Reverse
side
- Fold back to the left seam allowance.
Turn under the right seam allowance to
form 3mm (1/8 inch) fold.
2cm
- Attach the zipper foot. Attach the right
side of the presser foot pin to the holder
when sewing the left side of the zipper.
Attach the left side of the presser foot pin
to the presser foot holder when sewing
the right side of the zipper.
- Stitch the left side of zipper from bottom
to top.
- Turn the fabric right side out, stitch across
the lower end and right side of zipper.
- Stop about 5cm (2 inches) from the top of
zipper. Remove the basting and open the
zipper. Stitch the remaining part of the
seam.
44
Narrow hemming
The hemmer foot is used to stitch the narrow rolled hems usually found on shirt tails, table
linens and along the edge of frills.
* The hemmer foot accessory is optional. It
is not included with this machine.
00
K
3.5
1.5~3.0
Fold edge of fabric over about 3mm (1/8 inch),
then fold it over again 3mm (1/8 inch) for
about 5cm (2 inches) along the edge of the
fabric.
Insert the needle into the fold by rotating the
handwheel toward you, and lower the
presser foot. Sew several stitches and raise
the presser foot.
Insert the fabric fold into the spiral opening
of hemmer foot. Move fabric back and forth
until the fold forms a scroll shape.
Lower the presser foot and start sewing
slowly guiding the raw edge of the fabric in
front of the Hemmer foot evenly into the
scroll of the foot.
45
Cording
Used for embellishing 1 to 3 cords or decorative threads.
Sew over one strand of cording to create a pretty swirled design on a jacket or vest or sew over
three strands of cording for border trims. Pearl cotton, knitting yarn, embroidery floss, lace thread,
fine wool or lily yarn can be used for cording.
* The Cording foot accessory is optional. It is not included with this machine.
05
M
Single cording
Mark the design on the fabric. Insert the cord
in the center groove of the cording foot from
the right side opening. Pull the cord about
5cm (2 inches) behind the foot.
Place the cord under the grooves of the
Cording foot and pull the cord about 5cm (2
inches) behind the foot.
The grooves under the foot will hold the
length of the cord in place while the stitches
are being formed over the cord.
Select the stitch and adjust the stitch width
so that the stitches are just covering the cord.
Lower the foot and sew slowly, guiding the
cord over the design.
06
14
M
Triple cording
Mark the design on the fabric.
Insert three cords into the grooves of the
foot from the right side opening.
Place the cord under the grooves of the
cording foot and pull the cord about 5cm (2
inches) behind the foot.
The grooves under the foot will hold the
cords in place while the stitches are being
formed over the cords.
Select the stitch and adjust the stitch width so
that the stitches are just covering the cord.
Lower the foot and sew slowly, guiding the
cord over the design.
46
Satin stitch sewing
05
25
26
27
28
29
30
31
32
33
34
35
A
3.5~7.0
0.5~1.0
Use the embroidery foot for satin stitching
and sewing decorative stitches. This foot has
a full indentation on the bottom side of the
foot to allow easy sewing over the thickness
of the already sewn stitches.
To tailor the satin or decorative stitch pattern,
you may adjust the length and width of the
pattern by pressing the stitch length and
width adjustment buttons. Experiment with
fabric scraps until you get the desired length
and width.
Please Note:
When sewing very thin fabrics, it is suggested
that you use stabilizer on the backside of the
fabric.
47
Gathering
The Gathering Foot is used for gathering fabrics. Ideal for clothing as well as home decor,
works best on thin to medium weight fabrics.
00
3.5
* The gathering foot accessory is optional. It
is not included with this machine.
4.5
Gathered fabric
Remove the presser foot holder and attach
the gathering foot, lowering the tension
setting to below 2.
Place fabric to be gathered under presser
foot to the right of the presser foot.
Sew a row of stitching, keeping the raw edge
of fabric aligned with the right edge of foot.
The stitches automatically cause the fabric
to gather. Suitable for light to medium weight
fabrics. If your fabric is light, such as batiste
or lace, you will have more gathers.
To gather and attach gathered fabric in one
step
The gathering foot has a slot on the bottom.
When using the slot, you can gather the
bottom layer of the fabric while attaching it to
a flat top layer, such as the waistband on a
project.
- Remove the presser foot holder and attach
gathering foot.
- Place the fabric to be gathered with right
side up under the foot.
- Place top layer of the fabric right side down
in the slot.
- Guide the two layers as illustrated.
Note:
- When testing machine for adjustments to
achieve desired fullness, work with 10"
increments of the fabric, trims or elastic.
This makes it easier to determine the
adjustments and how much change is
needed for your project. Always test on your
project fabric and on the same grainline as
will be used in your finished project.
- Sew with slow to medium speed for better
fabric control.
48
Smocking
The decorative stitch created by stitching or embroidering over gathers is called "smocking".
It is used to decorate the front of blouses or cuffs. The smocking stitch adds texture and
elasticity to fabric.
13
14
A
Use the zigzag foot to sew basting lines 1cm
(3/8 inch) apart, across the area to be
smocked.
Basting
Knot the threads along one edge.
Pull the bobbin threads and distribute the
gathers evenly. Secure the threads at the
other end.
Bobbin
thread
Reduce the tension, if necessary and sew
decorative pattern stitches between the
straight seams.
Pull out the gathering basting.
49
Free motion darning, embroidery and monogramming
00
* The darning/ embroidery foot accessory is
optional. It is not included with this machine.
05
3.5~5.0
Move the drop feed control to "
lower the feed dog.
a
" to
b
b
a
a
Remove the presser foot holder, and attach
the darning foot to the presser foot holder bar.
The lever (a) should be behind the needle
clamp screw (b). Press the darning foot on
firmly from behind with your index finger and
tighten the screw (c).
b
c
Darning
First sew around the edges of the hole (to
secure the threads). Working from left to
right, sew over the hole in a constant and
continuous movement.
Turn the work by 1/4 and sew over the first
stitching moving the work slower over the
hole to separate the threads and not form
big gaps between the threads.
Please Note:
Free motion darning is accomplished without
the sewing machine internal feed system.
Movement of the fabric is controlled by the
operator. It is necessary to coordinate sewing
speed and movement of fabric.
50
Free motion darning, embroidery and monogramming
Embroidery
Select zigzag stitch and adjust the stitch
width as desired.
Stitch along the outline of the design by
moving the embroidery hoop. Make sure to
maintain a constant speed.
Fill in the design working from the outline
towards the inside. Keep the stitches close
together.
You will get longer stitches by moving the
hoop faster and shorter stitches by moving
the hoop more slowly.
Secure the work with reinforcement stitches
at the end by pressing the Auto-lock button.
Monogramming
Select the zigzag stitch pattern and adjust
the stitch width as desired. Sew at a constant
speed, moving the hoop slowly along the
lettering.
When the letter is finished. Secure the work
with reinforcement stitches at the end by
pressing the Auto-lock button.
* Embroidery hoop is not included with the
machine.
Please Note:
When you finish the work, move the drop feed
control to "
" to raise the feed dog.
51
Fagoting
12
T
Stitching across an open seam is called "fagoting". It is used on blouses and children's
clothing. This stitch is more decorative when thicker thread is used.
- Separate the folded edges of the fabric
pieces with a gap of 4mm (1/8 inch) and
baste them onto a piece of thin paper or
water-soluble stabilizer sheet.
Thin paper
Basting
- Align the center of the presser foot with the
center of the two pieces of fabric and begin
sewing.
- After sewing, remove the paper.
Patchworkstich
12
13
T
14
44
A
- Place the two pieces of fabric with the right
side together and sew with the straight
stitch.
- Open the seam allowances and press it flat.
- Place the center of the presser foot on the
seam line of the joined pieces of fabric and
sew over the seam.
52
Quilting
Sandwiching batting between the top and bottom layers of fabric is called "Quilting".
The top layer is usually formed by multiple geometrically shaped pieces of materials joined
together.
00
02
3.5
P
1.0~3.0
* The quilting foot accessory is optional. It is
not included with this machine.
Insert the right seam guide on the right in the
presser foot holder as illustrated and set the
space as you desire.
Sew the first row and move over the fabric to
sew successive rows with the guide riding
along the previous row of stitching.
Note:
When using the quilting foot, only use center
needle position stitches to prevent machine
damage.
Scallop stitch
The wave-shaped repeating stitch that looks like shells is called "scalloping". It is used on
the collars of blouses and to decorate the edges of projects.
27
78
T
A
- Stitch along the edge of the fabric, making
sure not to sew directly on the edge of the
fabric.
* For better results, apply spray starch
onto the fabric and press with a hot iron
before it is sewn.
- Trim along the stitches.
* Be careful not to cut the stitches.
53
Mirror
Select the pattern.
Pressing the mirror button. LCD will display
the mirror function and the machine will sew
the reflected stitch until you press the mirror
button again.
A. Normal pattern sewing.
B. Mirror pattern sewing.
A
B
Please Note:
- Pattern 15-24 cannot be mirror imaged.
- Mirror imaged patterns can also be
combined with other patterns.
54
Twin needle
* The twin needle is optional. It is not
include with the accessories.
T
2.0~5.0
Insert the twin needle.
Attention:
When using twin needles, use the zigzag
foot (T) regardless of what kind of sewing
foot will be recommended.
Use only twin needle assemblies with max.
2mm needle distance.
Follow the instructions for single-needle
threading using the horizontal spool pin.
Thread through the left needle.
Set the second spool pin (included with the
accessories) into the hole on the top of the
machine. Thread through remaining points,
making certain to omit the thread guide
above the needle and pass thread through
the right needle.
Thread each needle separately.
Please Note:
Make sure that the two threads used to
thread the twin needle are of the same
weight. You can use one or two colors.
Before sewing adjust the stitch width, turn the
handwheel to check the needle clearance, so
that needle does not hit the stitch plate.
Select a stitch pattern and start sewing.
Utility and decorative patterns 00-14, 25-99
can be used.
Sewing result will be a pattern with two
parallel stitch lines.
Please Note:
When sewing with twin needle, always
proceed slowly, and make sure to maintain a
low speed to insure quality stitching.
55
Walking foot
* The walking foot accessory is optional. It is not included with
this machine.
01
The walking foot accessory equalizes the feeding of the upper and lower layers of fabric and
improves the matching of plaids, stripes and patterns. It also helps to prevent uneven feeding of
very difficult fabrics.
Lift the presser foot lifter to raise the presser foot bar.
Remove the presser foot holder by unscrewing
(counterclockwise) the presser bar attaching screw.
a
b
c
Attach the walking foot to the machine as follows:
- The arm (a) should fit into the needle screw of the needle
holder clamp (b).
- Slide the plastic attaching head (c) from your left to right
so that it is fitted into the presser foot bar.
- Lower the presser foot bar.
- Replace and tighten (clockwise) the presser bar attaching
screw.
- Make sure both the needle screw and the presser bar
attaching screw are tightly secured.
Draw the bobbin thread up and place both the bobbin
thread and the needle thread behind the walking foot
attachment.
56
Memory
Combined patterns can be stored for later use. Since stored patterns are not lost after the
sewing machine is turned off, they can be recalled at any time. This is convenient for
patterns, such as names, that will be used often.
-
Please Note:
The machine has a program memory that can retain 30 units of stitches.
Multiple patterns selecting from pattern modes "
,
" can be combined and sewn
together.
All the units in the memory can be edited to set its function such as Stitch length, Stitch width,
Mirror and Auto-lock.
The Direct mode patterns and the patterns 15-24 can not be memorized.
Combining patterns or letters
When you turn the machine "ON", the LCD screen
displays "
".
Press the "
" button to enter the memory mode,
and store the combinations of character or
decorative stitches.
MEM
MEM
Press the "
" button to select any desired pattern
group among ".........." or ".........." on the LCD screen.
Then press the desired pattern number (e.g.13).
(You can change the stitch length, width, or choose
the Auto-stop, mirror function if desired.)
Repeat step 3 for more patterns to be stored in the
memory.
Please Note:
If the full memory of 30 units of stitches is reached,
the machine will signal this via beeping.
Use the arrow "
" or "
you have programmed.
MEM
57
" button to check what
Memory
Press the "
" button to leave the memory mode
and return to the Direct mode.
Attention:
The selected pattern will be cleared from the
memory module after closing the machine if you do
not press the "
" button again when you have
completed your selection.
Adding patterns or letters
MEM
While in the memory mode, press the "
" button or
the "
" button until the stitch number you have
selected is displayed, then add the new stitch or
change the stitch length, width, Auto-stop or mirror, if
desired.
Clearing patterns or letters
MEM
If you wish to delete a certain stitch within the
memory mode, use the "
" button or "
" button
until the actual stitch number is displayed.
Press the "
" button to delete the selected pattern
and the next pattern in the back will move forward.
Recalling and sewing the memorized pattern
MEM
Press the "
" button to enter the memory mode.
The machine will be positioned at the first
programmed stitch.
58
Memory
Press foot controller. The machine will start to sew
from first entered pattern. On the LCD screen,
sewing stitch data is indicated.
MEM
MEM
If you wish to check what is programmed or if you
wish to start sewing a few stitches in the memory
" button or "
" button.
mode, use the "
You can use the Auto-lock " " function when the
sewing machine should stop sewing after one
sequence.
Please Note:
If you wish to repeat your stitch combination without
having the machine stop, press the Auto-lock " "
button again to cancel the Auto-Stop in the memory
mode.
The " " will disappear from the LCD screen.
Press the "
" button to leave the memory mode
and return to the Direct mode.
59
Warning Functions
Instruction message display
Lowering the buttonhole lever
When you select any buttonhole pattern or
darning pattern, LCD screen will show the figure
"
". It is to remind you to lower the buttonhole
lever.
Bobbin winding
When the bobbin winder spindle is activated for
bobbin winding (in the rightmost position) this
figure appears on the LCD screen as a reminder.
Warning beeping sound
- When operating correctly: 1 beep
- When the memory is full 30 units of pattern: 2-short beeps
- When operating incorrectly: 3-short beeps
- When the sewing machine is in trouble and can't sew: 3-short beeps
It means that the thread is twisted or jammed and the hand wheel axle can't move. Please look
through the "Trouble shooting guide" on page 63/64 to find the solution. After the problem has
been solved, the machine will continue to sew.
Return bobbin winder spindle to left
If you press any button on the machine when
the bobbin is full or the bobbin winder spindle
is in the right position, then the machine will
beep 3 times as a warning.
Return the bobbin winder spindle to the left
position.
Please Note:
If the problem is still not solved, please contact your local dealer.
Attention:
During the sewing, if the thread get jammed inside the hook stopping the needle from moving and
you continue pressing the foot control, the security switch will stop the machine completely. In order
to restart the sewing machine, you will have to turn the on/off switch to the OFF position and then
ON again.
60
Maintenance
Attention:
Disconnect the power cord from the wall socket before cleaning the screen and sewing machine
surface, otherwise injury or electrical shock may result.
Cleaning the screen
If the front panel is dirty, wipe it gently with a soft, dry cloth.
Do not use any organic solvents or detergents.
Cleaning the sewing machine surface
If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it out
firmly and then wipe the surface. After cleaning it once in this way, wipe the surface again with a
dry cloth.
Attention:
This machine is equipped with a 100mW LED lamp. If lamp replacement is needed, please
contact nearest authorized retailer.
Cleaning the hook
If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of the
machine. Check regularly and clean the stitching mechanism when necessary.
Attention:
Disconnect the machine from the wall outlet before carrying out any maintenance.
Remove the bobbin cover plate and bobbin.
61
Maintenance
Remove the needle, presser foot and presser foot holder.
Remove the screws holding the stitch plate and remove the
stitch plate.
Clean the feed dog and bobbin case with a brush. Also
clean them, using a soft, dry cloth.
62
Trouble shooting guide
Before calling for service, check the following items. If the problem still persists, call our Ever
Sewn support Hotline or contact the place of purchase.
Problem
Cause
Upper
thread
breaks
1. The machine is not threaded correctly.
1. Rethread the machine.
10
2. The thread tension is too tight.
2. Reduce the thread tension (lower
number).
16
3. The thread is too thick for the needle.
3. Select a larger needle.
13
4. The needle is not inserted correctly.
4. Remove and reinsert the needle (flat
side towards the back).
13
5. The thread is wound around the spool 5. Remove the reel and wind thread onto
reel.
holder pin.
10
Correction
6. Replace the needle.
6. The needle is damaged.
Lower thread 1. The bobbin case is not inserted 1. Remove and reinsert the bobbin case
and pull on the thread. The thread
correctly.
breaks
Reference
13
9
should pull easily.
2. The bobbin case is not threaded 2. Check both bobbin and bobbin case.
corrected.
Skipped
stitches
1. The needle is not inserted correctly.
1. Remove and reinsert needle (flat side
towards the back).
13
2. The needle is damaged.
2. Insert a new needle.
13
3. The wrong size needle has been used. 3. Choose a needle to suit the thread.
Needle
breaks
Seam
gather or
pucker
13
4. The foot is not attached correctly.
4. Check and attach correctly.
14
5. The machine is not threaded correctly.
5. Rethread the machine.
10
1. The needle is damaged.
1. Insert a new needle.
13
2. The needle is not correctly inserted.
2. Insert the needle correctly (flat side
towards the back).
13
3. Wrong needle size for the fabric.
3. Choose a needle to suit the thread and
fabric.
13
4. The wrong foot is attached.
4. Select the correct foot.
5. The needle clamp screw is loose.
5. Use the screwdriver to firmly tighten the
screw.
6. The presser foot that is used is not 6. Attach the presser foot that is appropriate for the type of stitch that you wish
appropriate for the type of stitch that
to sew.
you wish to sew.
Loose
stitches
9
13
65-67
7. The upper thread tension is too tight.
7. Loosen the upper thread tension.
16
1. The machine is not correctly threaded.
1. Check the threading.
10
2. The bobbin case is not threaded 2. Thread the bobbin case as illustrated.
correctly.
9
3. Needle/ fabric/ thread combination is 3. The needle size must suit the fabric
wrong.
and thread.
13
4. Thread tension is wrong.
4. Correct the thread tension.
16
1. The needle is too thick for the fabric.
1. Select a finer needle.
13
2. The stitch length is adjusted wrong.
2. Readjust the stitch length.
26
3. The thread tension is too tight.
3. Loosen the thread tension.
16
63
Trouble shooting guide
Problem
Cause
Seam
puckering
1. The needle thread tension is too tight.
Correction
10
3. The needle is too heavy for the fabric 3. Choose a needle to suit the thread and
being sewn.
fabric.
13
4. The stitch length is too long for the 4. Make stitch length shorter.
fabric.
26
Patterns are 1. The correct presser foot is not used.
distorted
The
machine is
noisy
5. Sew with stabilising material under the
fabric.
1. Select the correct presser foot.
2. The needle thread tension is too tight.
2. Loosen the thread tension.
1. Thread is caught in the hook.
Remove the upper thread and bobbin case,
turn the handwheel
backwards and
forwards by hand and remove the thread
remains.
2. The feed dog is packed with fluff.
16
61
61
2. The needle is damaged.
13
4. Thread is caught in the hook.
The sewing
machine
doesn't
operate
13
1. Fluff or oil have collected on the hook 1. Clean the hook and feed dog as described.
or needle bar.
2. Replace the needle.
3. Slight humming sound coming from 3. Normal.
internal motor.
Uneven
stitches,
uneven
feed
16
2. The needle thread is not threaded 2. Rethread the machine.
correctly.
5. If you are sewing thin fabric.
The
machine
jams
1. Loosen the thread tension.
Reference
-
5. The feed dog is packed with fluff.
Remove the upper thread and bobbin case,
turn the handwheel backwards and forwards
by hand and remove the thread remains.
61
1. Poor quality thread.
1. Select a better quality thread.
13
2. The bobbin case is not threaded 2. Remove the bobbin case, the thread and
correctly.
reinsert correctly.
9
3. Fabric has been pulled.
3. Do not pull on the fabric while sewing, let
it be taken up by the machine.
7
1. The machine is not turned on.
1. Turn on the machine.
4
2. The presser foot lifter is raised.
2. Lower the presser foot lifter.
3. The machine is not plugged in.
3. Connect the power line plug to the electric
outlet.
64
15
4
Quick adjustment reference chart
Stitch Pattern
Utility
stitches
Width (mm)
Length (mm)
Presser
Foot
Mirror/Presser foot Twin needle
Manual
Auto
Manual
00
3.5
0.0~7.0
2.5
0.0~4.5
T
01
0.0
0.0~7.0
2.5
0.0~4.5
T
02
3.5
0.0~7.0
2.5
1.0~3.0
T
03
3.5
1.0~6.0
2.5
1.0~3.0
T
04
3.5
0.0~7.0
2.5
1.5~3.0
T
05
5.0
0.0~7.0
2.0
0.3~4.5
T
06
5.0
2.0~7.0
1.0
0.3~4.5
T
07
5.0
2.5~7.0
2.5
1.0~3.0
T
08
5.0
3.5~7.0
2.5
1.0~3.0
E
09
5.0
2.5~7.0
2.5
1.0~3.0
T
10
3.5
2.5~7.0
2.0
0.5~4.5
F
/T
11
3.5
2.5~7.0
1.0
0.5~4.5
F
/T
12
5.0
2.5~7.0
2.5
1.0~3.0
T
13
7.0
2.5~7.0
2.5
1.0~3.0
A
14
5.0
2.5~7.0
2.5
1.0~3.0
A
15
5.0
3.0~7.0
0.5
0.3~1.0
D
16
5.0
3.0~5.5
0.5
0.3~1.0
D
17
7.0
5.5~7.0
0.5
0.3~1.0
D
Buttonhole 18
stitches
5.0
3.0~5.5
0.5
0.3~1.0
D
19
5.0
3.0~5.5
0.5
0.3~1.0
D
20
6.0
3.0~7.0
1.0
1.0~2.0
D
3.0~7.0
1.5
1.0~3.0
D
--
--
A
21
6.0
Eyelet stitch
22
7.0 7.0,6.0,5.0
Darning
stitches
23
7.0
3.5~7.0
2.0
1.0~2.0
D
Bar tack stitch
24
2.0
1.0~3.0
0.5
0.5~1.0
D
25
7.0
2.5~7.0
0.5
0.3~1.0
A
26
7.0
2.5~7.0
0.5
0.3~1.0
A
27
7.0
2.5~7.0
0.5
0.3~1.0
A
28
7.0
2.5~7.0
0.5
0.3~1.0
A
29
7.0
2.5~7.0
0.5
0.3~1.0
A
30
7.0
2.5~7.0
0.5
0.3~1.0
A
31
7.0
2.5~7.0
0.5
0.3~1.0
A
32
7.0
2.5~7.0
0.5
0.3~1.0
A
33
7.0
2.5~7.0
0.5
0.3~1.0
A
34
7.0
2.5~7.0
0.5
0.3~1.0
A
35
7.0
2.5~7.0
0.5
0.3~1.0
A
36
7.0
2.5~7.0
0.5
0.3~1.0
A
Decorative
satin stitches 37
7.0
3.5~7.0
1.5
1.0~3.0
A
38
7.0
4.0~7.0
2.5
2.5~3.0
A
Satin
stitches
Functions
Reverse Auto-lock
Auto
65
/T
Memory
Quick adjustment reference chart
Width (mm)
Length (mm)
Auto
Manual
Auto
Manual
Presser
Foot
39
7.0
2.5~7.0
0.5
0.5~1.0
A
40
7.0
5.0~7.0
0.5
0.5~1.0
A
Decorative
satin stitches 41
7.0
4.0~7.0
0.5
0.5~1.0
A
42
7.0
2.5~7.0
0.5
0.4~1.0
A
43
7.0
2.5~7.0
1.0
1.0~2.0
A
44
5.0
2.5~7.0
2.5
1.0~3.0
A
45
4.0
3.0~7.0
1.0
1.0~3.0
A
46
4.0
3.0~7.0
1.0
1.0~3.0
A
47
6.0
3.0~7.0
1.5
1.0~3.0
A
48
6.0
5.0~7.0
1.5
1.0~3.0
A
49
6.0
3.0~7.0
1.0
1.0~3.0
A
50
6.0
3.0~7.0
1.0
1.0~3.0
A
51
6.0
3.0~7.0
1.0
1.0~3.0
A
52
6.0
3.0~7.0
1.5
1.0~3.0
A
53
5.0
2.5~7.0
2.0
1.0~4.5
T
54
4.0
2.5~7.0
2.0
1.0~4.5
T
55
3.5
2.5~7.0
2.5
1.5~3.0
T
56
3.5
2.5~7.0
2.5
1.5~3.0
T
57
4.0
2.5~7.0
2.5
1.5~3.0
A
58
3.5
2.5~7.0
2.5
1.5~3.0
T
59
6.0
3.0~7.0
2.0
1.0~4.5
T
60
7.0
3.0~7.0
1.5
1.0~4.5
T
61
6.0
3.0~7.0
2.0
1.0~3.0
T
62
5.0
3.0~7.0
2.0
1.0~3.0
T
63
5.0
2.5~7.0
2.0
1.0~3.0
T
64
6.0
3.5~7.0
1.5
1.0~3.0
T
65
5.0
3.5~7.0
1.5
1.5~3.0
A
66
5.0
2.5~7.0
1.0
1.0~4.5
T
67
6.0
3.0~7.0
2.0
1.0~3.0
T
68
7.0
2.5~7.0
1.5
1.0~3.0
A
69
5.0
2.5~7.0
2.5
1.0~3.0
A
70
7.0
3.0~7.0
2.0
1.0~3.0
A
71
6.0
4.5~7.0
1.5
1.0~3.0
A
72
5.0
3.0~7.0
3.0
1.5~3.0
A
Stitch Pattern
Cross
stitches
Quilt
stitches
73
7.0
4.0~7.0
3.0
2.0~3.0
A
Decorative 74
stitches
75
7.0
2.5~7.0
2.0
1.0~3.0
T
7.0
2.5~7.0
2.5
1.5~3.0
T
76
5.0
2.5~7.0
2.5
1.5~3.0
T
77
7.0
4.0~7.0
2.0
2.0~3.0
A
78
7.0
2.5~7.0
2.5
1.0~4.5
T
66
Functions
Reverse Auto-lock
Mirror/Presser foot Twin needle
Memory
Quick adjustment reference chart
Stitch Pattern
79
Width (mm)
Length (mm)
Presser
Foot
Auto
Manual
Auto
Manual
7.0
2.5~7.0
1.0
1.0~3.0
T
80
7.0
4.0~7.0
2.5
2.0~3.0
A
81
5.0
2.5~7.0
2.0
2.0~3.0
A
82
7.0
3.5~7.0
1.0
1.0~3.0
A
83
7.0
3.5~7.0
3.0
2.0~3.0
A
84
7.0
4.0~7.0
3.0
2.0~3.0
A
85
7.0
4.0~7.0
2.0
1.0~3.0
A
86
7.0
3.0~7.0
3.0
1.0~3.0
A
87
7.0
3.0~7.0
2.0
1.5~3.0
A
88
5.0
3.5~7.0
1.0
1.0~3.0
A
A
Decorative
89
stitches
4.0
4.0~7.0
2.0
2.0~3.0
90
7.0
3.0~7.0
2.0
1.5~3.0
A
91
7.0
2.5~7.0
2.0
1.0~3.0
A
92
7.0
2.5~7.0
2.5
1.5~3.0
A
93
7.0
3.5~7.0
2.5
1.5~3.0
T
94
7.0
3.5~7.0
2.0
1.5~3.0
T
95
7.0
2.5~7.0
2.0
1.5~3.0
T
96
5.0
2.5~7.0
2.0
1.0~3.0
T
97
5.0
2.5~7.0
2.0
1.0~3.0
T
5.0
6.0
3.5~7.0
2.0
1.5~3.0
T
4.0~7.0
2.0
2.0~3.0
A
98
99
67
Functions
Reverse Auto-lock
Mirror/Presser foot Twin needle
Memory
Quick adjustment reference chart
Alphabet
stitches
Width (mm)
Length (mm)
Auto
Manual
Auto
Manual
Presser
Foot
01
7.0
--
--
--
A
02
7.0
--
--
--
A
03
7.0
--
--
--
A
04
7.0
--
--
--
A
05
7.0
--
--
--
A
06
7.0
--
--
--
A
07
7.0
--
--
--
A
08
7.0
--
--
--
A
09
7.0
--
--
--
A
10
7.0
--
--
--
A
11
7.0
--
--
--
A
12
7.0
--
--
--
A
13
7.0
--
--
--
A
14
7.0
--
--
--
A
15
7.0
--
--
--
A
16
7.0
--
--
--
A
17
7.0
--
--
--
A
18
7.0
--
--
--
A
19
7.0
--
--
--
A
20
7.0
--
--
--
A
21
7.0
--
--
--
A
22
7.0
--
--
--
A
23
7.0
--
--
--
A
24
7.0
--
--
--
A
25
7.0
--
--
--
A
26
7.0
--
--
--
A
27
7.0
--
--
--
A
28
7.0
--
--
--
A
29
7.0
--
--
--
A
30
7.0
--
--
--
A
31
7.0
--
--
--
A
32
7.0
--
--
--
A
33
7.0
--
--
--
A
34
7.0
--
--
--
A
35
7.0
--
--
--
A
36
Stitch Pattern
7.0
--
--
--
A
37
7.0
--
--
--
A
38
7.0
--
--
--
A
39
7.0
--
--
--
A
40
7.0
--
--
--
A
68
Functions
Reverse Auto-stop
Mirror/Presser foot Twin needle
Memory
Quick adjustment reference chart
Alphabet
stitches
Width (mm)
Length (mm)
Auto
Manual
Auto
Manual
Presser
Foot
41
7.0
--
--
--
A
42
7.0
--
--
--
A
43
7.0
--
--
--
A
44
7.0
--
--
--
A
45
7.0
--
--
--
A
46
7.0
--
--
--
A
47
7.0
--
--
--
A
48
7.0
--
--
--
A
49
7.0
--
--
--
A
50
7.0
--
--
--
A
51
7.0
--
--
--
A
52
7.0
--
--
--
A
53
7.0
--
--
--
A
54
7.0
--
--
--
A
55
7.0
--
--
--
A
56
7.0
--
--
--
A
57
7.0
--
--
--
A
58
7.0
--
--
--
A
59
7.0
--
--
--
A
60
7.0
--
--
--
A
61
7.0
--
--
--
A
62
7.0
--
--
--
A
63
7.0
--
--
--
A
64
7.0
--
--
--
A
65
7.0
--
--
--
A
66
7.0
--
--
--
A
67
7.0
--
--
--
A
68
7.0
--
--
--
A
69
7.0
--
--
--
A
70
7.0
--
--
--
A
71
7.0
--
--
--
A
72
7.0
--
--
--
A
73
7.0
--
--
--
A
74
7.0
--
--
--
A
75
7.0
--
--
--
A
76
Stitch Pattern
7.0
--
--
--
A
77
7.0
--
--
--
A
78
7.0
--
--
--
A
79
7.0
--
--
--
A
80
7.0
--
--
--
A
69
Functions
Reverse Auto-stop
Mirror/Presser foot Twin needle
Memory
Quick adjustment reference chart
Alphabet
stitches
Width (mm)
Length (mm)
Auto
Manual
Auto
Manual
Presser
Foot
81
7.0
--
--
--
A
82
7.0
--
--
--
A
83
7.0
--
--
--
A
84
7.0
--
--
--
A
85
7.0
--
--
--
A
86
7.0
--
--
--
A
87
7.0
--
--
--
A
88
7.0
--
--
--
A
89
7.0
--
--
--
A
90
7.0
--
--
--
A
91
7.0
--
--
--
A
92
7.0
--
--
--
A
93
7.0
--
--
--
A
94
7.0
--
--
--
A
95
7.0
--
--
--
A
96
7.0
--
--
--
A
97
7.0
--
--
--
A
Stitch Pattern
70
Functions
Reverse Auto-stop
Mirror/Presser foot Twin needle
Memory
Download PDF
Similar pages