Formula Pro
®
Please visit
www.babybrezza.ca
®
For instructional video, tips & more.
This product may be covered under one or more of the following including
U.S. Patent No. 8,584,901 and pending patent application(s) in the U.S. and other countries.
©2014 Baby Brezza® Enterprises LLC
DISTRIBUTED BY:
ELFE JUVENILE PRODUCTS
4500 THIMENS BLVD
SAINT-LAURENT (QC) H4R 2P2
SERVICE@ELFE.CA I WWW.ELFE.COM I 1-800-667-8184
MADE IN CHINA
Instructions
Important Safeguards
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces.
3. To protect against electric shock and injury to persons do not immerse cord, plug,
water tank or appliance in water or other liquid.
4. Close supervision is necessary when any appliance is used near children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before inserting or
removing parts, and before cleaning the appliance.
6. Do not operate this appliance with a damaged cord or plug. If the appliance
malfunctions or has been damaged in any manner, contact Elfe at 1-800-667-8184 or
by e-mail at: service@elfe.ca
7. The use of accessory attachments not recommended by the appliance
manufacturer may cause fire, electric shock or injury.
8. Use on level surface and be sure there is no debris under the unit and the rubber
pads are touching the surface.
9. Household use only. Do not use outdoors.
10. Do not let cord hang over edge of table or counter, or touch hot surfaces.
11. Do not place on or near hot gas or electric burner, or in a heated oven.
12. Do not use appliance for other than intended use.
13. Do not attempt to use the machine without water in the water tank.
14. This appliance has a polarized plug (one blade wider than the other). To reduce
risk of electric shock, this plug is intended to fit into a polarized outlet only one
way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
15. Make sure machine is turned off before unplugging.
16. A short power-supply cord is provided to reduce risks of becoming entangled in or tripping
over a longer cord. Longer detachable power-supply cords or extension cords are available
and may be used if care is exercised in their use. If using the machine with an extension cord,
make sure the cord is the proper electrical rating for the machine. The extension cord should
be arranged so that it does not drape over countertop or tabletop where it can be pulled on
by children or tripped over unintentionally.
17. Before serving make sure formula mixture is at safe temperature for baby.
18. Avoid contact with moving parts. Never remove powder container, powder
container lid, funnel or water tank while machine is in operation.
19. Do not disassemble.
Warning:
For infants less than 6 months old, always use bottled water suitable for infant
formula preparation. Tap water and/or unsterilized baby bottles can potentially lead
to adverse effects for the health of your baby. Only prepare one bottle at a time, feed
immediately and follow all instructions carefully. Do not keep leftover formula mix.
Always hold baby while feeding. Leaving baby unattended may cause choking.
TECHNICAL DATA
Supply voltage: 120V ~ 60Hz
Model: FRP0045
Current: 2.5A
Heater Power: 250W
Motor Power: 20W
Save these instructions
Components
Powder Container
Parts
wash all before first use
Powder
Container
Lid
Stirring
Wheel
Locking
Cover
Silicone Scraper
wash before first use
Water
Tank
Lid
wash before
first use
Measuring
Wheel
Water
Tank
Measuring
Inserts
1,3,4,5
wash before
first use
Powder
Container
Funnel
Cover
wash before
first use
Control
Panel
Funnel
wash before
first use
Base
Bottle
Grate
Power
Cord
Drip
Tray
Funnel
Compartment
...................................................................
Controls & Indicator Lights
Water ounce indicator LEDs
No Water
warning LED
Water temperature
indicator LEDs
300/10
60/2 120/4
180/6 240/8
ml/oz
Water ml/oz selector button
Funnel Out
Warning LED
Stop Button (red)
Start Button (green)
Set up - Before First Use
Wash: Funnel, Funnel Cover, Inside of Water Tank, and all Powder Container parts. (see page 2).
Do not put the Powder Container or any of the Powder Container parts in the dishwasher.
After washing, make sure all Powder Container parts are COMPLETELY DRY before assembly.
Assemble:
Select measuring insert by powder type
1
See next page for details
Inserts are numbered
1, 3, 4 and 5. Do not use
the Measuring Wheel
without an insert.
2
Press selected insert into
bottom of Measuring Wheel.
3
Place Powder
Container on top
of Base and Insert
Measuring Wheel.
Make sure Silicone Scraper is installed correctly
Insert
and does not protrude through the hole in the
Locking Cover
powder container after assembly. See separate
Silicone Scraper instructions for more details.
and turn
to
lock under tabs in
Powder Container.
4
After steps 2 & 3
Turn the Measuring
Wheel to the position
shown at left, with
the small arrows on
the Measuring Wheel
& Powder Container
Top
aligned.
View
5
Insert
Stirring Wheel.
don’t add
powder.
6
Place Lid as shown
below. turn
to lock.
Rinse
internal
parts:
make
sure tab
on lid is
on the
back
corner of
machine.
2
Plug in machine and turn
power switch to ON position.
3
Front
1
Fill Water Tank to MAX
line with room temp.
Purified Water.
With Powder
Container
assembled
follow these
steps to rinse
internal parts.
Choose 300 ml (10 oz)
size by pressing ml/oz
button 4 times.
60/2
120/4
180/6
240/8 300/10
ml/oz
don’t add
powder.
4
Place 300 ml
10 ounce
or larger
container
to catch water.
Press start
(green)
to begin rinsing.
The machine will stop after dispensing 300 ml (10oz) of water. Dispose of the water captured in the container.
The Formula pro® is now ready to use. Follow the instructions on pages 5 & 6 for bottle preparation.
Bottle Preparation
Bottle Preparation Continued
3
Before preparing a bottle with the Formula Pro® :
1
Fill Water Tank to MAX line
with room temperature
purified water.
2
Fill Powder Container
to MAX line with
formula powder.
b
for aby
mu
la
• Always use a clean and sterilized bottle, nipple or other feeding equipment.
• Wash and dry hands before handling sterilized bottles.
• Make each bottle as needed, and do not store mixed formula for later use.
Short Bottle
Tall Bottle
Pure
H20
Select correct height for Drip
Tray based on bottle height.
Lift up and pull out to remove.
Push in and down to install.
Adjust the drip tray so the bottle is as
close to the Funnel outlet as possible.
This will make sure no formula spills
outside of the bottle.
MAX
4
5
60/2 120/4
180/6
Pour powder loosely and evenly into Powder Container. Do not pack powder inside
or overfill Powder Container. Powder can be spread evenly with the 3 arms on the
Powder Container Lid before closing.
About water temperature
The heater in the Water Tank will
warm the water and keep it warm as
long as the machine is powered on.
If you refill the Water Tank with cool
or room temperature water and
need to use the machine right away,
the machine can be used while
water is heating (flashing yellow light).
If you run the machine with cool or
room temperature water, before the
water is warm and ready, always
make sure formula is mixed properly
and check for clumps.
Temperature Indicator Lights
Solid Green = Water warm and ready.
Flashing Yellow = Water heating.
Flashing Yellow & Green = Water poured
into tank is too hot or too cold.
For quickest warming time, always fill the water tank with
room temperature or cool water . Flashing green & yellow
lights mean the water poured into in the Water Tank is too
hot or too cold. The machine will not work while the green
& yellow lights flash. If you don’t want to wait long for the
water to heat, do not fill with water stored in the refrigerator.
Never fill Water Tank with hot water. If you boil water
before using it in the machine, let the water cool to
body or room temperature before pouring it into the
Water Tank.
Bottle Preparation continued on next page
6
240/8 300/10
60/2 120/4
300/10
180/6 240/8
ml/oz
ml/oz
Select bottle size by pressing the ounce
button. With each push, the amount will
increase 60 ml (2 oz).
When desired ml/oz size is selected,
press the start button (green) to
dispense formula.
Machine will dispense
formula into bottle and
stop automatically
when done.
7
8
8oz
6oz
4oz
2oz
Check level of mixed
formula.
Check
temperature
of formula...
...and feed baby.
Level will appear higher
due to added powder
volume.
Never remove Water Tank, Funnel or Powder Container while machine is in operation.
After baby stops feeding from bottle, discard any leftover formula mixture.
Always hold the bottle when feeding baby. Never prop the bottle up and leave your baby
to feed unsupervised.
Cleaning
User Tips
Unplug the appliance before cleaning. Do not use abrasive pads to clean the machine.
...................................................................
We recommend cleaning The Funnel, Funnel Cover and underside of Powder Container
once per day (if machine is used daily). Follow these steps to clean the machine parts.
2
1
Remove Funnel and
Funnel Cover by pulling
out and down.
3
Remove Funnel Cover
from Funnel by lifting
up on Funnel Cover.
4
Wash and rinse Funnel &
Funnel Cover thoroughly.
Funnel and Funnel Cover
are top rack dishwasher safe
and are also safe for steam
sterilization.
With the Funnel removed and Powder Container
attached to machine, wipe any dry formula powder
from the underside of the Powder Container & Funnel
Compartment in a circular motion with a DRY paper
towel or DRY soft cloth.
Do not remove the Water Tank from the base to refill.
Simply lift the Water Tank Lid at the front and pour water in.
Make sure to keep water above “MIN” line.
Refill Water Tank regularly with room temperature water
and keep machine powered on. This way, the water will always
be warm and ready to serve.
Always make sure powder level is above the top of the
Stirring Wheel. You will know it’s time to refill the Powder
Container when any of the four horizontal arms of the
Stirring Wheel are visible through the powder. Do not use
the machine when the powder level is below the MIN line
marked on the Powder Container.
When setting up the Powder Container Parts, always make
sure the Measuring Wheel and Locking Cover are set up with
the arrows aligned as shown in the illustration at right.
If the Measuring Wheel rotates when installing the Locking
Cover, rotate the Measuring Wheel to the position shown
at right.
Refill when arms of
stirring wheel are
visible
Top
View
Never use a wet or damp cloth to clean the Funnel
Compartment or underside of Powder Container.
Wipe underside of powder
container with clean, dry cloth.
Always make sure the Funnel and Funnel Cover
are completely DRY before placing in machine.
...................................................................
• The inside of the Water Tank should be cleaned once a month with mild detergent and soft
cloth or sponge. Rinse inside of Water Tank thoroughly before refilling with clean, purified
water. Wipe the outside of the Water Tank with a damp clean cloth.
Never immerse Water Tank or get the electronics in the base of the Water Tank wet.
If the electronics in the base of the Water Tank get wet, allow to air dry thoroughly before
placing back on base. Never place Water Tank in dishwasher.
• The Powder Container and Powder Container Parts should be cleaned once a month
by emptying any remaining powder (powder can be saved for refill) and cleaned with mild
detergent and soft cloth or sponge.
Make sure Powder Container and all Powder Container
Parts are completely dry before reassembly and refilling the Powder Container with powder.
Never place Powder Container in dishwasher.
• The machine Base should be wiped with a damp, soft cloth or sponge and dried immediately.
Never submerge the base or plug in water or other liquids. Dry machine Base after cleaning.
ALWAYS FOLLOW INSTRUCTIONS AND NOTE EXPIRY DATE ON POWDER MANUFACTURER LABEL
If the powder forms a cone shape mound
when refilling the Powder Container,
use the 3 arms on the bottom of the
Powder Container Lid to gently level
the powder.
Adjust the Drip Tray so the bottle is as close to the
funnel outlet as possible. This will make sure no
formula spills on the outside of the bottle.
The Formula Pro® can be used at any time during the water heating cycle, but not all powders
mix well with cool or room temperature water. Always check for clumps & shake or stir the
closed bottle gently to mix the powder completely with the water.
Troubleshooting
Condition
Machine will
not start.
Possible Cause
Troubleshooting
Remedy
Unit is unplugged.
Make sure the plug is securely
inserted into the power outlet.
Unit is not turned on.
Turn switch on lower back of
unit from off to on.
Funnel is removed or not fully
inserted.
Insert funnel or push front of
funnel until flush with machine.
Water Tank is removed or not
fully seated.
Place water tank on base or
push down all the way.
Water level is below “MIN” line.
Add more water to water tank.
Powder container is removed
or not fully seated.
Place powder container on
base or push down all the way.
Powder container lid is not
completely closed.
Turn Powder container lid
clockwise to close completely.
Powder container lid is on
backwards.
Make sure tab on outer edge of
Powder Container Lid is facing the
back of the machine and engaged
with safety switch.
See page 3, step 6 for diagram.
Water in Water Tank is too cold.
( Green & Yellow Temp LEDs Flashing)
Water in Water Tank is too hot.
( Green & Yellow Temp LEDs Flashing)
Allow water to warm up or pour
warmer water in Water Tank to
raise temperature faster.
Allow water to cool down or pour
cool water in Water Tank to
lower temperature faster.
Temperature of
dispensed formula
is too cold.
Water has not been heated
to correct temperature.
Wait for heater to warm water
in tank. Green LED in “temp”
section of control panel will
illuminate when water reaches
correct temperature.
Not enough
powder dispensed.
Powder level in powder
container is too low.
Refill Powder Container with
more powder.
Powder is stuck in powder
measuring wheel.
Make sure silicone scraper is
installed correctly.
Incorrect insert for powder
type.
Make sure to use the correct insert
for powder type. See page 4.
Condition
Possible Cause
Remedy
Too much
powder dispensed.
Incorrect insert for powder
type.
Make sure to use the correct insert
for powder type. See page 4.
Scaling on
water tank
heater plate.
Mineral rich water used
persistently.
Clean heater plate and use
purified/distilled water.
Powder build-up
on funnel cover
and underside of
powder container.
Frequent use in high humidity.
Clean funnel cover and powder
container bottom frequently and
use machine away from humid
areas.
Water Tank is full,
red no water light
is on.
Water Tank not fully seated.
Push Water Tank down all the way
on Base.
Funnel will not fit
all the way in Funnel
Compartment.
Funnel Cover is not straight
on funnel or not pushed down
completely.
Align tab on front of Funnel Cover
with notch in Funnel and push
down Funnel Cover completely.
If you can not remedy problems with the machine by using the troubleshooting chart above,
please contact Customer Service at 1-800-667-8184 or service@elfe.ca.
Customer Service and Warranty
If you are experiencing problems with your Baby Brezza® Formula Pro®,
please call our Customer Service department at 1-800-667-8184 or email at: service@elfe.ca
before returning the product so that we can offer you the best service.
Limited 1-Year Warranty
The limited warranty is valid only on products bought through authorized resellers and used in
Canada. Buying through an unauthorized reseller or using this product outside of Canada
automatically voids this warranty.
This warranty is available to consumers only. You are a consumer if you own a Baby Brezza®
Formula pro® that was purchased at retail for personal, family or household use. Except as
otherwise required under applicable law, this warranty is not available to retailers or other
commercial purchasers or owners. We warrant that your Baby Brezza® Formula Pro® will be free of
defects in material or workmanship under normal home use for one year from the date of original
purchase. Customer will be required to present original proof of purchase in order to obtain the
warranty benefits. In the event that you do not have proof of purchase date, the purchase date for
purposes of this warranty will be the date of manufacture. If your Baby Brezza® Formula Pro®
should prove to be defective within the warranty period, please call Customer Service
at 1-800-667-8184 or write to: service@elfe.ca
Download PDF
Similar pages