A-SERIES (2018) manual_ENGLISH_10-18

FCC Statements
Moultrie Products
MCG-13273
A-40 PRO
Instructions for A-Series Digital Game Cameras
Moultrie Products
MCG-13272
A-40i PRO
Moultrie Products
MCG-13212
A-35
Moultrie Products
MCG-13296
A-25
Moultrie Products
MCG-13297
A-25i
THANK YOU for your purchase of an A-Series Digital Game Camera. Please read this booklet before using the unit. If you should
have any questions about this product or any other Moultrie product, please contact us using the information on the back of
this booklet. Please register your camera at www.moultriefeeders.com/warranty to activate your warranty.
Note: changes and modifications not expressly approved by the party responsible could void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Motion Sensor
NOTE: This device complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- lncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Camera Lens
Status Indicator
LCD Display
Mode Selector Switch
www.moultriefeeders.com
Release for
Battery Compartment
PRADCO Outdoor Brands • 3280 Highway 31, Ste B • Calera, AL 35040
10182017 / MCG-13273 • MCG-13272 • MCG-13212 • MCG-13296 • MCG-13297
A-SERIES (2018) manual_ENGLISH_10-18-17.indd 1
Infrared LED Flash
External Power Port
Light Sensor
OK Button
SD Card Slot
Up/Down Buttons
Micro USB Port
10/18/17 9:39 AM
A
QUICK START INSTRUCTIONS
Important Battery lnformation
Battery Installation
- Only use Alkaline or Lithium batteries. We recommend the use of Energizer batteries.
- Do not mix old and new batteries. Always replace ALL the batteries at the same time.
- When the camera is not in use, please remove the batteries.
Note: Anytime you load or unload batteries, make sure that the camera is OFF.
Moultrie Limited Warranty
TIP: Do not remove batteries if you have an external 12-volt power source connected. Batteries serve as a backup power source in case external
power source fails.
This product has been thoroughly tested and inspected before shipment. It is guaranteed from defects in material and workmanship from the
date of purchase for 2 years. Under this limited guarantee we agree to replace or repair free of charge any part or parts which have been found to
be defective in original material or workmanship. Should you require in-warranty service, call our Customer Service Department. If your problem
cannot be addressed over the telephone, we may need you to send us your defective product plus proof of purchase.
Open the camera cover and install 8 AA Alkaline or Lithium batteries. Make sure that the (+ and -) polarities match the polarities indicated inside
the battery chamber.
Insert SD Card
You will need to open the front cover to insert an SD memory card. You can insert a
SD Card up to 32 GB (not included). Insert the SD card in the direction indicated on the
card, until you hear an audible click.
Note: Camera will not operate without an SD memory card installed. Ultra/turbo SD
cards are not recommended.
Power ON
Slide the Mode Switch to the On position. The battery level will appear on the
LCD Display. The camera has powered up.
2
A-SERIES (2018) manual_ENGLISH_10-18-17.indd 2
You must register your camera at www.moultriefeeders.com/warranty to activate your 2-year warranty.
Troubleshooting
Please visit www.moultriefeeders.com/contact-us for troubleshooting and helpful tips.
Returns and Repairs
Please visit http://www.moultriefeeders.com/return-policy and complete the form or our Service Department will gladly answer any questions
you have. Call 800-653-3334, Monday - Friday, 8:00 AM to 5:00 PM CST.
MOULTRIE MOBILE® COMPATIBILITY
Your camera is compatible with our Moultrie Mobile® cellular service when combined with the Field Modem MV1. Please visit www.moultriemobile.com
for more information.
7
10/18/17 9:39 AM
B
Power ON
Slide the (Mode) Switch to the (Setup)
position. Press and hold the (ON/OFF)
Button until the time appears on the LCD
Display. The camera will power up.
CAMERA SETUP (cont.)
Mounting with a Strap
Setting Camera ID
Use the Up/Down buttons to choose between nine different numbers (1-9) to help identify
your cameras (i.e. “CAMERA 3” will be marked on the info strip given 3 was selected).
Mounting with a Strap
Press OK to lock in your selection and move to the next selection.
Close cover andHiplace camera on a tree or
pole approximately 3 ft. high. Thread
the mounting strap through the mounting
Reset Picture Count/Erase Images/Format Card
strap slots on the back of the camera
You can reset the picture count on the camera. Use the Up/Down buttons to choose
and secure.
between Yes or No. Press the OK button to confirm the selection. “Yes” will reset
Hint: If you are Hi
mounting camera to cover a
file number to start from 0001 and erase all images stored on the SD card.
trail face the camera down the trail tilted at
NOTE: This will also format your SD card for use in your camera.
a slight downward angle.
Face the camera North or South to avoid
over exposure from the sun.
SET
OK
OK
HOUR
MINUTE
AM/PM
Clear brush
away
from camera front to
TIME
OK
avoid false triggers from the
wind.
Close cover and place camera on a tree or pole approximately 3 ft. high.
Thread the mounting strap through the mounting strap slots on the back
of the camera and secure.
Hint: If you are mounting camera to cover a trail, face the camera down
the trail tilted at a slight downward angle.
Face the camera north or south to avoid over exposure from the sun.
Clear brush away from camera front to avoid false triggers from the wind.
Trail
NO
SET
DATE
MONTH
DAY
OK
OK
YEAR
OK
SET
OPTIONS
DETECTION
DELAY
6
A-SERIES (2018) manual_ENGLISH_10-18-17.indd 3
OK
CAPTURE
MODE
OK
CAMERA
ID
OK
Eyelet
Trail
YES
7
Mounting
Strap
DELETE/
FORMAT SD
3
10/18/17 9:39 AM
B
CAMERA SETUP
Power ON
Slide the power switch to the ON position. The battery level will appear on the LCD Display
for 2 seconds.
Hi
After 2 seconds, the camera will display the countdown. When the countdown timer reaches
“00”, the display will turn off and the camera will OK Capture Mode.
Hi
99
09
If the camera detects that the battery level is 15% or below, the Low Battery screen will
appear and the unit will turn off.
Setting Time and Date
While the camera is in the Setup mode, the LCD display will show the time.
Press the OK button and the selection will flash. Use the UP/Down buttons to
change the selection. Press the OK button to lock in the selection and move to
the next selection. Repeat the process to set the year, month and day.
AM
Hi
Detection Delay Setting
Detection Delay determines the number of minutes between pictures when
an animal is detected and remains in range. Press the OK button. Use the
Up/Down buttons to choose between (0, 15, 30 sec, 1 or 5 min). Press OK to
lock in your selection and move to the next selection.
AM
Hi
Hi
To begin modifying the camera settings, slide the switch to the SETUP position. The camera will display the currently set time. Use the UP and DOWN
arrow keys to change the currently flashing option. Once setting is adjusted to the desired option, press OK to lock in the setting and move to the next
field/option.
Note: while in SETUP mode, the motion sensor will detect movement and illuminate the STATUS LED on the front of the camera for ~1 second.
You can use this feature to ensure camera is properly aimed to detect movement in the desired target area.
4
A-SERIES (2018) manual_ENGLISH_10-18-17.indd 4
Setting Capture Mode
Use the Up/Down buttons to choose between 5 different modes:
1 Photo/Low Resolution, 1 Photo/High Resolution, 3 Photos/Low Resolution,
3 Photos/High Resolution and Video. Press OK to lock in your selection and
move to the next selection.
The on-screen icons for each mode are shown to the right:
Lo
Hi
Lo
Hi
1
1 Photo, Low Resolution
1
1 Photo, High Resolution
3
3 Photos, Low Resolution
3
3 Photos, High Resolution
Video
5
10/18/17 9:39 AM
Download PDF
Similar pages