LINK Media Conversion Products
Ethernet Series...
UT-0012
Product Summary& Benefits:
10Base-T to 10Base-2 Converter
The UT-0012 media converter was specifically designed to
offer the network designer a simple solution for migrating
from a coaxial based to a UTP based network. Now,
migration or expansion of existing networks can be achieved
with minimum cost and complexity. The converter is
completely transparent
when installed so the network
performs exactly the way it did before - only now, it allows
the co-existence of both UTP and coaxial mediums.
Expands the Size of an Existing Network - provides
UTP/Coaxial connectivity to Ethernet segments which allowing
for even further networking expansion between extended
nodes. It allows for the quick and easy addition of UTP
segments to existing coaxial networks.
Enhances the Distance between Networking Devices connecting the UT-0012 to UTP segments can further extend
distances of up to 185 meters beyond the converter for a
total segment length of 285 meters. The UT-0012 can be
connected to a Fiber converter for even longer distances.
Introduction:
The UT-0012 has been designed to accommodate
the need for media conversion between 10Base-T
UTP media and 10Base-2 coaxial media. Both types
of media are still very common and the need to add
UTP to coaxial segments are widespread.
This converter has found great popularity with cable
installers and network designers alike. It offers an
inexpensive and easy alternative to layering or
replacement of cables.
Cabling Flexibility - allows network managers to put fiber
cabling anywhere within a network without retrofitting the
arrangement of the Ethernet network. Its compact size
allows the converter to be easily deployed in any narrow
desktop location or used in wall-mount installation. Several
converters can be simultaneously installed by using the
UT-3012 12-slot 19" rack-mount chassis, UT-3004 4-slot
rack-mount chassis.
Features:
Complies with 802.3 10Base-T/2 standards
Ordering Information:
UT-0012:
10Base-T to 10Base-2 Converter
MDI/MDI-X push button selection on RJ-45 port
connection
Extended distances up to 285m
NOTE : Above models available with internal AC/DC
power supply options (used with the UT-3001
Mini Converter Chassis)
Operates in half duplex mode
Compatible with other 10Base-T/2 devices
Link, receive status LEDs
External and internal power supply options
FCC ClassA & CE approved
Quick Reference
UT-0012
Connector #
Con.1
Type
RJ-45
BNC
10Base-T
10Base-2
UTP
Coaxial
Protocol
Cable Type
Distance
FCC
Class A
9 Ethernet Series...
Approval
Bandwidth
100 m
10 Mbps
Con.2
185 m
10 Mbps
LINK Media Conversion Products
Ethernet Series...
Specifications:
Standard:
Connector:
Max. Distance:
Unit LED:
Delay:
Switch:
Power:
Temperature:
Humidity:
Emissions:
Dimensions
Weight:
IEEE 802.3
10Base-T/2
1x shielded RJ-45, 1x BNC
UTP:
100 meters (Cat.3)
Coaxial:
185 meters
PWR:
Illuminated for normal operation
PART:
Illuminated when partitioning occurs
LNK:
Illuminated when receiving link pulses from complaint device
RCV:
Illuminated or flashing when data packets are being transmitted/received
Same as class 1 repeater, typically less than 23 Bit
Push button for MDI/MDI-X operation
Voltage:
AC voltage to 12V DC 0.8A power adapter
Frequency:
47Hz to 63Hz
Operating:
0°C to 50°C
Storage:
-20°C to 70°C
Operating:
10% to 80% RH
Storage:
5% to 90% RH
FCC Part 15 of Class A & CE approved
109.2 x 73.8 x 23.4 mm (L x W x H)
160 g
Applications:
The following illustrates typical applications for UT-0012. The actual distances will depend on several factors including the
quality of cables used and the terminal equipment employed.
Ethernet Hub / Switch
100 m
UT-0012
UTP
185 m
RG-58 A/U Coaxial Cable
Ethernet Hub / Switch
100 m
UT-0012
UTP
185 m
RG-58 A/U Coaxial Cable
Ethernet Hub / Switch
185 m
RG-58 A/U Coaxial Cable
185 m
UT-0012
UT-0012
Coaxial
100 m
UTP
Fiber
UTP/STP
Coaxial
Ethernet Series... 10
Download PDF
Similar pages