HP 7500 Switch Series - CNET Content Solutions

QuickSpecs
HP 7500 Switch Series
Overview
Product overview
The HP 7500 Switch Series comprises modular, multilayer chassis switches that meet the evolving needs of integrated services
networks and can be deployed in multiple network environments, including the enterprise LAN core, aggregation layer, and wiring
closet edge. The series switches offer 40 GbE connectivity and cost-effective, wire-speed 10-Gigabit Ethernet ports to safeguard the
throughput and bandwidth needed for your mission-critical data and high-speed communications. A passive backplane, support for
load sharing, and redundant management and fabrics help the series provide high availability. Moreover, these switches deliver wirespeed Layer 2 and Layer 3 routing services for the most demanding applications with hardware-based IPv4 and IPv6 support.
HP 7502 Switch Chassis
Key features
Versatile, high-performance modular switches
Enterprise LAN core, aggregation, and edge
Extensive switching and routing, IPv6, MPLS
Advanced functionality with service modules
Robust network and service virtualization
Features and benefits
Quality of Service (QoS)
IEEE 802.1p prioritization: delivers data to devices based on the priority and type of traffic
Class of Service (CoS): sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP
port number, source port, and DiffServ
Bandwidth shaping:
Port-based rate limiting: provides per-port ingress-/egress-enforced increased bandwidth
Classifier-based rate limiting: uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each
port
DA - 13805 North America — Version 31 — March 19, 2014
Page 1
QuickSpecs
HP 7500 Switch Series
Overview
Reduced bandwidth: provides per-port, per-queue egress-based reduced bandwidth
Weighted random early detection (WRED)/random early detection (RED): delivers congestion avoidance capabilities through
the use of queue management algorithms
Powerful QoS feature: supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR),
weighted fair queuing (WFQ), and WRED
Traffic policing: supports Committed Access Rate (CAR) and line rate
Intrusion detection/prevention system (IDS/IPS)
Deep packet inspection: module supports deep packet inspection and examines the packet payload as well as the frame and
packet headers; packets are dropped if attacks or intrusions are detected using signature-based or protocol anomaly-based
detection
Signature-based detection: detects attacks that have known attack patterns; IPS maintains a signature database that contains
the pattern definitions for known attacks that can be automatically updated using a subscription service
Protocol anomaly-based detection: detects attacks that use anomalies in application protocol payloads
Severity-based action policies: involve action taken against attacks based on their severity; available actions are "allow,"
"block," and "terminate connection" to provide appropriate mitigation
Signature update service: provides regular updates to the signature database, helping to ensure that the latest available
signatures are installed
Virtual private network (VPN)
IPSec: provides secure tunneling over an untrusted network such as the Internet or a wireless network; offers data
confidentiality, authenticity, and integrity between two network endpoints
Generic Routing Encapsulation (GRE): transports Layer 2 connectivity over a Layer 3 path in a secured way; enables the
segregation of traffic from site to site
Manual or automatic Internet Key Exchange (IKE): provides both manual or automatic key exchange required for the
algorithms used in encryption or authentication; auto-IKE allows automated management of the public key exchange, providing
the highest levels of encryption
Management
Management interface control: provides management access through a modem port and terminal interface, as well as in-band
and out-of-band Ethernet ports; provides access through terminal interface, telnet, or secure shell (SSH)
Industry-standard CLI with a hierarchical structure: reduces training time and expenses, and increases productivity in
multivendor installations
Management security: restricts access to critical configuration commands; offers multiple privilege levels with password
protection; ACLs provide telnet and SNMP access; local and remote syslog capabilities allow logging of all access
SNMPv1, v2, and v3: provide complete support of SNMP; provide full support of industry-standard Management Information
Base (MIB) plus private extensions; SNMPv3 supports increased security using encryption
Web management: embedded HTML management tool with secure access (SSHv2)
sFlow (RFC 3176): provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network
performance; this allows network operators to gather a variety of sophisticated network statistics and information for capacity
planning and real-time network monitoring purposes
Remote monitoring (RMON): uses standard SNMP to monitor essential network functions; supports events, alarm, history, and
statistics group plus a private alarm extension group
FTP, TFTP, and SFTP support: offers different mechanisms for configuration updates; FTP allows bidirectional transfers over a
TCP/IP network; trivial FTP (TFTP) is a simpler method using User Datagram Protocol (UDP); Secure File Transfer Protocol (SFTP)
runs over an SSH tunnel to provide additional security
Debug and sampler utility: supports ping and traceroute for both IPv4 and IPv6
DA - 13805 North America — Version 31 — March 19, 2014
Page 2
QuickSpecs
HP 7500 Switch Series
Overview
Network Time Protocol (NTP): synchronizes timekeeping among distributed time servers and clients; keeps timekeeping
consistent among all clock-dependent devices within the network so that the devices can provide diverse applications based on
the consistent time
Network Quality Analyzer (NQA): analyzes network performance and service quality by sending test packets, and provides
network performance and service quality parameters such as jitter, TCP, or FTP connection delays and file transfer rates; allows
a network manager to determine overall network performance and to diagnose and locate network congestion points or failures
IEEE 802.1AB Link Layer Discovery Protocol (LLDP): advertises and receives management information from adjacent devices
on a network, facilitating easy mapping by network management applications
Dual flash images: provide independent primary and secondary operating system files for backup while upgrading
Multiple configuration files: can be stored to the flash image
Connectivity
High-density port connectivity: up to 10 interface module slots; up to 40 40-GbE ports, 84 10GbE ports, 480 Fiber Gigabit
ports, or 480 PoE-enabled ports per HP 7500 series system
Jumbo frames: up to 9216 bytes allow high-performance backups and disaster-recovery systems
Loopback: supports internal loopback testing for maintenance purposes and an increase in availability; loopback detection
protects against incorrect cabling or network configurations and can be enabled on a per-port or per-VLAN basis for added
flexibility
Ethernet operations, administration and maintenance (OAM): detects data link layer problems that occurred in the "last mile"
using the IEEE 802.3ah OAM standard; monitors the status of the link between two devices
Flexible port selection: includes 100/1000BASE-X auto speed selection, 10/100/1000BASE-T auto speed detection, plus auto
duplex and MDI/MDI-X
Monitor link: collects statistics on performance and errors on physical links, increasing system availability
IEEE 802.3af Power over Ethernet (PoE): provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such
as IP phones, wireless access points, and security cameras
Dual-personality functionality: includes four 10/100/1000 ports or SFP slots for optional fiber connectivity such as Gigabit-SX,
-LX, and -LH, or 100-FX
Packet storm protection: protects against unknown broadcast, unknown multicast, or unicast storms with user-defined
thresholds
Flow control: provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
IEEE 802.3at Power over Ethernet (PoE+) support: provides up to 30 watts of power at the power sourcing equipment (PSE)
Performance
High-speed fully distributed architecture:
2.4 Tbps backplane supports maximum 1152 Gbps switching capacity, providing enhanced performance and future
expansion capability; with dual fabrics, the switch delivers up to 714 Mpps throughput
All switching and routing is performed in the I/O modules
Meets current and future demand of an enterprise's bandwidth-intensive applications
Scalable system design: backplane is designed for bandwidth increases; provides investment protection to support future
technologies and higher-speed connectivity
Flexible chassis selection: enables customers to tailor their product selection to their budgets, with a choice of six chassis,
ranging from a 10-slot to a 2-slot chassis
Resiliency and high availability
Redundant/Load-sharing fabrics, management, fan assemblies, and power supplies: increase total performance and power
available while providing hitless, stateful failover
All modules are hot-swappable: allows replacement of modules without any impact on other modules
DA - 13805 North America — Version 31 — March 19, 2014
Page 3
QuickSpecs
HP 7500 Switch Series
Overview
Dual internal power supply: provides high reliability
Separate data and control paths: keep control separated from services and keep service processing isolated; increase security
and performance
Passive design system: backplane has no active components for increased system reliability
IEEE 802.3ad Link Aggregation Control Protocol (LACP): supports up to 128 trunks, each with 8 links per trunk; supports static
or dynamic groups and user-selectable hashing algorithm
Intelligent Resilient Framework (IRF): creates virtual resilient switching fabrics, where two or more switches perform as a
single L2 switch and L3 router; switches do not have to be co-located and can be part of a disaster-recovery system; servers or
switches can be attached using standard LACP for automatic load balancing and high availability; can eliminate the need for
complex protocols like Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
simplifies network operation by eliminating the complexity of Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP
IRF capability: provides single IP address management for a resilient virtual switching fabric of up to four switches
Rapid Ring Protection Protocol (RRPP): provides standard sub-100 ms recovery for ring Ethernet-based topology
Virtual Router Redundancy Protocol (VRRP): allows a group of routers to dynamically back each other up to create highly
available routed environments
Hitless patch upgrades: allow patches and new service features to be installed without restarting the equipment, increasing
network uptime and facilitating maintenance
Graceful restart: features are fully supported, including graceful restart for OSPF, IS-IS, BGP, LDP, and RSVP; the network
remains stable during the active-standby switchover; after the switchover, the device quickly learns the network routes by
communicating with adjacent routers; forwarding remains uninterrupted during the switchover to achieve nonstop forwarding
(NSF)
Ultrafast protocol convergence with standards-based failure detection—Bidirectional Forwarding Detection (BFD) enables
link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and IRF
Smart link: allows 50 ms failover between links
IP/LDP FRR: nodes are configured with backup ports, routes, and LSPs; local implementation requires no cooperation of adjacent
devices, simplifying the deployment; solves the traditional convergence faults in IP forwarding and MPLS forwarding, protecting
the links, nodes, and paths without establishing respective backup LSPs for them; realizes restoration within 50 ms, with the
restoration time independent of the number of routes and fast link switchovers, without route convergence
Layer 2 switching
VLAN: supports up to 4,096 ports or IEEE 802.1Q-based VLANs; also supports MAC-based VLANs, protocol-based VLANs, and IPsubnet-based VLANs for added flexibility
Port isolation: increases security by isolating ports within a VLAN while still allowing them to communicate with other VLANs
Bridge Protocol Data Unit (BPDU) tunneling: transmits Spanning Tree Protocol BPDUs transparently, allowing correct tree
calculations across service providers, WANs, or MANs
GARP VLAN Registration Protocol: allows automatic learning and dynamic assignment of VLANs
Port mirroring: duplicates port traffic (ingress and egress) to a local or remote monitoring port; supports four mirroring groups,
with an unlimited number of ports per group
Spanning Tree Protocol (STP)
fully supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE
802.1s Multiple Spanning Tree Protocol (MSTP)
Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) protocol snooping: effectively control and
manage the flooding of multicast packets in a Layer 2 network
Device Link Detection Protocol (DLDP): monitors link connectivity and shuts down ports at both ends if unidirectional traffic is
detected, preventing loops in STP-based networks
IEEE 802.1ad QinQ and Selective QinQ: increase the scalability of an Ethernet network by providing a hierarchical structure;
connect multiple LANs on a high-speed campus or metro network
Super VLAN: RFC 3069 standard, also called VLAN aggregation, is used to save IP address space
Per-VLAN Spanning Tree Plus (PVST+): allows each VLAN to build a separate spanning tree to improve link bandwidth usage in
DA - 13805 North America — Version 31 — March 19, 2014
Page 4
QuickSpecs
HP 7500 Switch Series
Overview
network environments where multiple VLANs exist
Layer 3 services
Address Resolution Protocol (ARP): determines the MAC address of another IP host in the same subnet; supports static ARPs;
gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when
subnets are separated by a Layer 2 network
User Datagram Protocol (UDP) helper: redirects UDP broadcasts to specific IP subnets to prevent server spoofing
Dynamic Host Configuration Protocol (DHCP): simplifies the management of large IP networks and supports client and server;
DHCP Relay enables DHCP operation across subnets
Domain Name System (DNS): provides a distributed database that translates domain names and IP addresses, which simplifies
network design; supports client and server
Layer 3 routing
Static IPv4 routing: provides simple manually configured IPv4 routing
Routing Information Protocol (RIP): uses a distance vector algorithm with UDP packets for route determination; supports
RIPv1 and RIPv2 routing; includes loop protection
Open Shortest Path First (OSPF)
delivers faster convergence; uses this link-state routing Interior Gateway Protocol (IGP), which supports ECMP, NSSA, and MD5
authentication for increased security and graceful restart for faster failure recovery
Intermediate system to intermediate system (IS-IS): uses a path vector Interior Gateway Protocol (IGP), which is defined by the
ISO organization for IS-IS routing and extended by IETF RFC 1195 to operate in both TCP/IP and the OSI reference model
(Integrated IS-IS)
Border Gateway Protocol 4 (BGP-4): delivers an implementation of the Exterior Gateway Protocol (EGP) utilizing path vectors;
uses TCP for enhanced reliability for the route discovery process; reduces bandwidth consumption by advertising only
incremental updates; supports extensive policies for increased flexibility; scales to very large networks
Policy-based routing: makes routing decisions based on policies set by the network administrator
IP performance optimization: is a set of tools to improve the performance of IPv4 networks; includes directed broadcasts,
customization of TCP parameters, support of ICNP error packets, and extensive display capabilities
Unicast Reverse Path Forwarding (uRPF): is defined by RFC 3704 and limits erroneous or malicious traffic
Static IPv6 routing: provides simple manually configured IPv6 routing
Dual IP stack: maintains separate stacks for IPv4 and IPv6 to ease the transition from an IPv4-only network to an IPv6-only
network design
Routing Information Protocol next generation (RIPng): extends RIPv2 to support IPv6 addressing
OSPFv3: provides OSPF support for IPv6
IS-IS for IPv6: extends IS-IS to support IPv6 addressing
BGP+: extends BGP-4 to support Multiprotocol BGP (MBGP), including support for IPv6 addressing
IPv6 tunneling: allows IPv6 packets to traverse IPv4-only networks by encapsulating the IPv6 packet into a standard IPv4
packet; supports manually configured, 6to4, and Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) tunnels; is an
important element for the transition from IPv4 to IPv6
Multiprotocol Label Switching (MPLS): uses BGP to advertise routes across Label Switched Paths (LSPs), but uses simple labels
to forward packets from any Layer 2 or Layer 3 protocol, thus reducing complexity and increasing performance; supports
graceful restart for reduced failure impact; supports LSP tunneling and multilevel stacks
Multiprotocol Label Switching (MPLS) Layer 3 VPN: allows Layer 3 VPNs across a provider network; uses MP-BGP to establish
private routes for increased security; supports RFC 2547bis multiple autonomous system VPNs for added flexibility
Multiprotocol Label Switching (MPLS) Layer 2 VPN: establishes simple Layer 2 point-to-point VPNs across a provider network
using only MPLS Label Distribution Protocol (LDP); requires no routing and therefore decreases complexity, increases
performance, and allows VPNs of non-routable protocols; uses no routing information for increased security; supports Circuit
Cross Connect (CCC), Static Virtual Circuits (SVCs), Martini draft, and Kompella-draft technologies
DA - 13805 North America — Version 31 — March 19, 2014
Page 5
QuickSpecs
HP 7500 Switch Series
Overview
Virtual Private LAN Service (VPLS): establishes point-to-multipoint Layer 2 VPNs across a provider network
Service loopback: allows any module to take advantage of higher-featured modules, including OAA modules, by redirecting
traffic; reduces investment and enables higher bandwidth and load sharing; supports IPv6, IPv6 multicast, tunneling, and MPLS
Security
Access control list (ACL): supports powerful ACLs for both IPv4 and IPv6; ACLs are used for filtering traffic to prevent
unauthorized users from accessing the network, or for controlling network traffic to save resources; rules can either deny or
permit traffic to be forwarded; rules can be based on a Layer 2 header or a Layer 3 protocol header; rules can be set to operate
on specific dates or times
Remote Authentication Dial-In User Service (RADIUS)
eases switch security access administration by using a password authentication server
Terminal Access Controller Access-Control System (TACACS+)
is an authentication tool using TCP with encryption of the full authentication request that provides additional security
Switch management logon security: helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+
authentication
Secure Shell (SSHv2): uses external servers to securely log in to a remote device; with authentication and encryption, it protects
against IP spoofing and plain-text password interception; increases the security of Secure FTP (SFTP) transfers
Dynamic Host Configuration Protocol (DHCP) snooping: ensures DHCP clients receive IP addresses from authorized DHCP
servers and maintains a list of DHCP entries for trusted ports; prevents users from receiving fake IP addresses and reduces ARP
attacks, improving security
IP source guard: filters packets on a per-port basis to prevent illegal packets from being forwarded
ARP attack protection: protects from attacks using a large number of ARP requests with a host-specific, user-selectable
threshold
Port security: allows access only to specified MAC addresses, which can be learned or specified by the administrator
IEEE 802.1X support
provides port-based user authentication with support for Extensible Authentication Protocol (EAP) MD5, TLS, TTLS, and PEAP
with choice of AES, TKIP, and static or dynamic WEP encryption for protecting wireless traffic between authenticated clients and
the access point
Media access control (MAC) authentication: provides simple authentication based on a user's MAC address; supports local or
RADIUS-based authentication
Multiple user authentication methods:
IEEE 802.1X: is an industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in
conjunction with a RADIUS server
Web-based authentication: is similar to IEEE 802.1X and provides a browser-based environment to authenticate clients
that do not support the IEEE 802.1X supplicant
MAC-based authentication: authenticates the client with the RADIUS server based on the client's MAC address
DHCP protection: blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Endpoint Admission Defense (EAD): provides security policies to users accessing a network
Port isolation: secures and adds privacy, and prevents malicious attackers from obtaining user information
Convergence
LLDP-MED (Media Endpoint Discovery): is a standard extension of LLDP that stores values for parameters such as QoS and VLAN
to automatically configure network devices such as IP phones
Multicast Source Discovery Protocol (MSDP): is used for inter-domain multicast applications, allowing multiple PIM-SM
domains to interoperate
Internet Group Management Protocol (IGMP):is used by IP hosts to establish and maintain multicast groups; supports IGMPv1,
v2, and v3; utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks
Protocol Independent Multicast (PIM): is used for IPv4 and IPv6 multicast applications; supports PIM Dense Mode (PIM-DM),
DA - 13805 North America — Version 31 — March 19, 2014
Page 6
QuickSpecs
HP 7500 Switch Series
Overview
Sparse Mode (PIM-SM), and Source-Specific Mode (PIM-SSM)
Multicast Border Gateway Protocol (MBGP): allows multicast traffic to be forwarded across BGP networks and kept separate
from unicast traffic
Multicast Listener Discovery (MLD) protocol: is used by IP hosts to establish and maintain multicast groups; supports v1 and v2
and utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv6 multicast networks
Multicast VLAN: allows multiple VLANs to receive the same IPv4 or IPv6 multicast traffic, reducing network bandwidth demand
by eliminating multiple streams to each VLAN
Voice VLAN: automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
Integration
Open Application Architecture (OAA)
provides high-performance application-specific modules fully integrated with the switching architecture; uses the chassis highspeed backplane to access network-related data; increases performance, reduces costs, and simplifies network management
Load-balancing module
local and global server load-balancing module improves traffic distribution using powerful scheduling algorithms, including
Layer 4 to 7 services; monitors the health status of servers and firewalls
NetStream module: provides traffic analysis and statistics capture to allow network administrators to rapidly identify network
anomalies and security threats, as well as capacity planning information; supports NetFlow v5 and v9
Unified wired-WLAN module
supports up to 1,024 access points per module; is for use with selected HP APs (see the HP 10500/7500 20G Unified Wired-WLAN
Module data sheet for specifics); provides N+1, N+N, and 1+1 redundancy offering subsecond failover; provides IPv4/IPv6 and
end-to-end QoS; includes flexible forwarding modes, as well as Wi-Fi Clear Connect Radio Frequency (RF) optimization and
integrated IDS
VPN 20 Gbps firewall module
provides enhanced stateful packet inspection and filtering; supports flexible security zones and virtual firewall containment;
advanced VPN services with 3DES and AES encryption at high performance and low latency; Web content filtering; application
prioritization and optimization
Additional information
Green initiative support
provides support for RoHS and WEEE regulations
Low power consumption
is rated among the lowest in power consumption in the industry by Miercom independent tests
Unified HP Comware operating system with modular architecture
all switching, routing, and security platforms leverage the Comware OS, a common unified modular operating system; provides
an easy-to-enhance-and-extend feature set without wholesale changes
OPEX savings
are delivered through the use of a common operating system that simplifies and streamlines deployment, management, and
training, thereby cutting costs as well as reducing the chance for human errors associated with having to manage multiple
operating systems across different platforms and network layers
Warranty and support
1-year Warranty 2.0
advance hardware replacement with 10-calendar-day delivery (available in most countries)
Electronic and telephone support (for Warranty 2.0)
limited electronic and 24x7 telephone support is available from HP for the entire warranty period; to reach our support centers,
refer to www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase,
refer to www.hp.com/networking/warrantysummary
DA - 13805 North America — Version 31 — March 19, 2014
Page 7
QuickSpecs
HP 7500 Switch Series
Overview
Software releases
to find software for your product, refer to www.hp.com/networking/support; for details on the software releases available with
your product purchase, refer to www.hp.com/networking/warrantysummary
DA - 13805 North America — Version 31 — March 19, 2014
Page 8
QuickSpecs
HP 7500 Switch Series
Configuration
Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
HP 7502 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
4U - Height
JD242B
HP 7503 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
10U - Height
JD240B
HP 7503-S Switch Chassis w/1 Fabric Slot
Must select min 1 Power Supply
Must select Min 1 Fabric Module
4U - Height
JD243B
HP 7503 Swch w/48p GT 2p 10G 384Gbps MPU
Must select min 1 Power Supply
1 - JD193B - HP 384 Gbps A7500 Fab Mod w/2 XFP Ports included min=0 \ max=2 XFP Transceivers
1 - JD229B - HP 48p Gig-T PoE+ Ext A7500 Module included
4U - Height
JG507A
HP 7506 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
13U - Height
JD239B
HP 7506 Swch w/96p GT 2p 10G 384Gbps MPU
Must select min 1 Power Supply
1 - JD193B - HP 384 Gbps A7500 Fab Mod w/2 XFP Ports included min=0 \ max=2 XFP Transceivers
1 - JD229B - HP 48p Gig-T PoE+ Ext A7500 Module included
13U - Height
JG508A
HP 7506-V Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
21U - Height
HP 7510 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
16U - Height
JD241B
JD238B
HP 7510 Swch w/96p GT 768Gbps MPU
DA - 13805 North America — Version 31 — March 19, 2014
Page 9
QuickSpecs
HP 7500 Switch Series
Configuration
Must select min 1 Power Supply
1 - JD220A - HP 384 Gbps A7500 Fab Mod w/2 XFP Ports included min=0 \ max=2 XFP Transceivers
1 - JD229B - HP 48p Gig-T PoE+ Ext A7500 Module included
16U - Height
Remarks
JG509A
BTO Model 1s should never receive an 0D1 and therefore can not be factory integrated into a
rack.
Box Level Integration CTO Models
HP 75xx CTO Switch Solution
SSP trigger sku
JG707A
HP 7502 Switch Chassis CTO
Must select min 1 Power Supply
Must select Min 1 Fabric Module
4U - Height
JD242B
See Configuration Note:
2,3
HP 7503 Switch Chassis - CTO
Must select min 1 Power Supply
Must select Min 1 Fabric Module
10U - Height
JD240B
See Configuration Note:
3,4
HP 7503 Switch Chassis with 1 Fabric Slot - CTO
Must select min 1 Power Supply
Must select Min 1 Fabric Module
4U - Height
JD243B
See Configuration Note:
2,3
HP 7506 Switch Chassis - CTO
Must select min 1 Power Supply
Must select Min 1 Fabric Module
13U - Height
JD239B
See Configuration Note:
3,4
HP 7506 Vertical Switch Chassis - CTO
Must select min 1 Power Supply
Must select Min 1 Fabric Module
21U - Height
JD241B
See Configuration Note:
3,4
HP 7510 Switch Chassis - CTO
Must select min 1 Power Supply
Must select Min 1 Fabric Module
16U - Height
JD238B
See Configuration Note:
3,4
Configuration Rules:
DA - 13805 North America — Version 31 — March 19, 2014
Page 10
QuickSpecs
HP 7500 Switch Series
Configuration
Note 2
If this Switch is selected at least one of these Power Supply with is required: (Use #0D1 if switch is CTO)
HP 7502 300W AC Power Supply
JD226A
HP 7500 650W DC Power Supply
JD209A
HP 7500 650W AC Power Supply
JD217A
Note 3
If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch
Chassis and integrated to the JG707A - HP 7500 CTO Enablement. (Min 1/Max 1 Switch per SSP)
Note 4
If this Switch is selected at least one of these Power Supplies is required: (Use #0D1 if switch is CTO)
HP 7500 1400W DC Power Supply
JD208A
HP 7500 1400W AC Power Supply
JD218A
HP 7500 2800W AC Power Supply
JD219A
HP 7500 6000W AC Power Supply
JD227A
Rack Level Integration CTO Models
HP 7502 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
4U - Height
JD242B
See Configuration Note:
1, 3
HP 7503 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
10U - Height
JD240B
See Configuration Note:
3,4
HP 7503-S Switch Chassis w/1 Fabric Slot
Must select min 1 Power Supply
Must select Min 1 Fabric Module
4U - Height
JD243B
See Configuration Note:
1, 3
HP 7506 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
13U - Height
JD239B
See Configuration Note:
3,4
HP 7506-V Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
21U - Height
JD241B
See Configuration Note:
3,4
HP 7510 Switch Chassis
Must select min 1 Power Supply
Must select Min 1 Fabric Module
16U - Height
JD238B
See Configuration Note:
3,4
DA - 13805 North America — Version 31 — March 19, 2014
Page 11
QuickSpecs
HP 7500 Switch Series
Configuration
Configuration rules:
Note 1
If this Switch is selected at least one of these Power Supply with is required: (Use #0D1 if switch is CTO)
HP 7502 300W AC Power Supply
JD226A
HP 7500 650W DC Power Supply
JD209A
HP 7500 650W AC Power Supply
JD217A
Note 3
If HP CTO Switch Chassis is selected to be Rack Level Integration, Then the CTO Switch Chassis needs to
integrate (with #0D1) to the BW966A and BW968A HP Universal Rack Only. (Default to the BW966A.)
Note 4
If this Switch is selected at least one of these Power Supplies is required: (Use #0D1 if switch is CTO)
HP 7500 1400W DC Power Supply
JD208A
HP 7500 1400W AC Power Supply
JD218A
HP 7500 2800W AC Power Supply
JD219A
HP 7500 6000W AC Power Supply
JD227A
Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.
Internal Power Supplies
System (std 0 // max 2) User Selection (min 1 // max 2)
See Configuration
Note:3
HP 7502 300W AC Power Supply
includes 1 x c13, 300w
JD226A
See Configuration
Note: 1,4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
#B2C
HP 7500 650W DC Power Supply
JD209A
See Configuration
Note: 1
HP 7500 650W AC Power Supply
includes 1 x c13, 650w
JD217A
See Configuration
Note: 1,4,5
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
DA - 13805 North America — Version 31 — March 19, 2014
#B2B
Page 12
QuickSpecs
HP 7500 Switch Series
Configuration
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
#B2C
HP 7500 1400W DC Power Supply
JD208A
See Configuration
Note: 2
HP 7500 1400W AC Power Supply
includes 1 x c19, 1400w
JD218A
See Configuration
Note: 2,4
PDU Cable NA/MEX/TW/JP
C15 C19 PDU Jumper Cord (NA/MEX/TW/JP)
JD218A#B2B
PDU Cable ROW
C19 PDU Jumper Cord (ROW)
JD218A#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JD218A#B2E
HP 7500 2800W AC Power Supply
includes 2 x c19, 2800w
JD219A
See Configuration
Note: 2,4,6
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
HP 7500 6000W AC Power Supply
includes 4 x c19, 6000w
#B2E
JD227A
See Configuration
Note: 2,4,6
PDU Cable NA/MEX/TW/JP
C15 C19 PDU Jumper Cord (NA/MEX/TW/JP)
JD227A#B2B
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JD227A#B2E
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
#B2E
Configuration Rules:
Note 1
Only supported on the JD242x and JD243x.
Note 2
Only supported on the JD238x,JD239x,JD241x, JD240x, JG507A, JG508A, and JG509A.
DA - 13805 North America — Version 31 — March 19, 2014
Page 13
QuickSpecs
HP 7500 Switch Series
Configuration
Note 3
If 2 power supplies are selected they must be the same Sku number.
Note 4
Localization required on orders without #B2B, #B2C, #B2D or #B2E options.
Note 5
If CTO Switch Chassis is ordered #0D1 (Rack Integrated), Then #B2B, or #B2C is Required on
the Power Supply's. (Optional when Switch is not Factory Racked. See Drop down remark in
Power Supplies section.)
Note 6
If the CTO Switch Chassis is ordered #0D1 (Rack Integrated), Then #B2D is Required on the
Power Supply's. (Optional when Switch is not Factory Racked. See Drop down remark in
Power Supplies section.)
Remarks:
Drop down under power supply should offer the following options and results:
Switch to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C
ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)
High Volt Power Electrical Module to Wall Power Cord - #B2E Option. (Offered only in North
America, Mexico, Taiwan, and Japan)
Modules
Ethernet Modules
(Switch JD243x and JD242x ) System (std 0 // max 2) User Selection (min 0 // max 2) per enclosure
(Switch JG507A) System (std 1 // max 2) User Selection (min 0 // max 1) per enclosure
(Switch JD240x) System (std 0 // max 3) User Selection (min 0 // max 3) per enclosure
(Switch JD239x and JD241x ) System (std 0 // max 6) User Selection (min 0 // max 6) per enclosure
(Switch JG508A) System (std 2 // max 6) User Selection (min 0 // max 4) per enclosure
(Switch JD238x) System (std 0 // max 10) User Selection (min 0 // max 10) per enclosure
(Switch JG509A) System (std 2 // max 10) User Selection (min 0 // max 8) per enclosure
HP 7500 24-port GbE SFP Module
min=0 \ max=24 SFP Transceivers
JD203B
See Configuration
Note:1
HP 7500 12-port GbE SFP Module
min=0 \ max=12 SFP Transceivers
JD207A
See Configuration
Note:1
DA - 13805 North America — Version 31 — March 19, 2014
Page 14
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7500 48-port GbE SFP Enhanced Module
min=0 \ max=48 SFP Transceivers
JD221A
See Configuration
Note:1
HP 7500 24p GbE SFP Mod w/8 Combo Ports
min=0 \ max=24 SFP Transceivers
JD223A
See Configuration
Note:1
HP 7500 40p Gig-T/8p SFP PoE-ready Mod
min=0 \ max= 8 SFP Transceivers
JD228B
See Configuration
Note:1, 8, 14
HP 7500 24-port GbE SFP Enhanced Module
min=0 \ max=24 SFP Transceivers
JD231A
See Configuration
Note:1
HP 7500 24-port GbE SFP Extended Module
min=0 \ max=24 SFP Transceivers
JD234A
See Configuration
Note:1
HP 7500 48-port GbE SFP Extended Module
min=0 \ max=48 SFP Transceivers
JD237A
See Configuration
Note:1
HP 7500 48-port GbE SFP Module
min=0 \ max=48 SFP Transceivers
JD211B
See Configuration
Note:1
HP 7500 24-port GbE SFP SC TAA Module
min=0 \ max=24 SFP Transceivers
JC704A
See Configuration
Note:1, 9
HP A7500 40p Gig-T/8p SFP PoE SC TAA Mod
min=0 \ max= 8 SFP Transceivers
JC710A
See Configuration
Note:1, 8, 9, 14
HP A7500 16p GbE SFP/8p Combo EB TAA Mod
min=0 \ max=24 SFP Transceivers
JC715A
See Configuration
Note:1, 9
HP A7500 16p GbE SFP/8p Combo SD TAA Mod
min=0 \ max=24 SFP Transceivers
JC718A
See Configuration
Note:1, 9
HP 7500 48-port GbE SFP SD TAA Module
DA - 13805 North America — Version 31 — March 19, 2014
JC721A
Page 15
QuickSpecs
HP 7500 Switch Series
Configuration
min=0 \ max=48 SFP Transceivers
See Configuration
Note:1, 9
HP A7500 20p Gig-T/4p Cmb PoE-upg SC Mod
min=0 \ max= 4 SFP Transceivers
JC669A
See Configuration
Note:1, 12
HP 7500 48-port 100BASE-FX Module
min=0 \ max=48 SFP 100 Transceivers
JD197B
See Configuration
Note:2, 7
HP 7500 8-port 10G SFP+ Module
min=0 \ max=8 per SFP+ Transceivers
JF290A
See Configuration
Note:3
HP 7500 8-port 10GbE SFP+ SC TAA Module
min=0 \ max=8 per SFP+ Transceivers
JC723A
See Configuration
Note:3, 9
HP 7500 4-port 10GbE XFP Enhanced Module
min=0 \ max=4 XFP
JD232A
See Configuration
Note:4
HP 7500 2-port 10GbE XFP Enhanced Module
min=0 \ max=2 XFP
JD233A
See Configuration
Note:4
HP 7500 8-port 10GbE XFP Extended Module
min=0 \ max=8 XFP Transceivers
JD191A
See Configuration
Note:4
HP 7500 2-port 10GbE XFP Module
min=0 \ max=2 XFP Transceivers
JD201A
See Configuration
Note:4
HP 7500 24p Gig-T / 2p 10GbE XFP Mod
min=0 \ max=2 XFP Transceivers
JD206A
See Configuration
Note:4
HP 7500 4-port 10GbE XFP Extended Module
min=0 \ max=4 XFP Transceivers
JD235A
See Configuration
Note:4
HP 7500 2-port 10GbE XFP Extended Module
min=0 \ max=2 XFP Transceivers
JD236A
See Configuration
Note:4
DA - 13805 North America — Version 31 — March 19, 2014
Page 16
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7500 24p GbE SFP / 2p 10GbE XFP Mod
min=0 \ max=2 XFP min=0 \ max=24 SFP Transceivers
JD205A
See Configuration
Note:5
HP 7500 24p GbE-SFP/2p 10GbE XFP Ext Mod
min=0 \ max=2 XFP min=0 \ max=24 SFP Transceivers
JD230A
See Configuration
Note:5
HP 7500 24-port Gig-T Module
No supported Transceivers
JD204B
HP 7500 48-port Gig-T Module
No supported Transceivers
JD210A
See Configuration
Note:8,14
HP 7500 48p Gig-T PoE+ Extended Module
Includes DIMM
JD229B
HP 7500 48p 1000BASE-T PoE+ SC Mod
No supported Transceivers
JG663A
HP 7500 48p 1000BASE-T PoE+ SC TAA Mod
No supported Transceivers
JG664A
HP 7500 Load Balancing Module
No supported Transceivers
JD252A
HP 7500 NetStream Monitoring Module
No supported Transceivers
JD254A
HP 7500 SSL VPN Module w/500-user Lic
No supported Transceivers
JD253A
HP S1200N IPS A7500 Module
No supported Transceivers
JC527A
HP 7500 48-port 10/100BASE-T Module
No supported Transceivers
JD198B
See Configuration
Note:7, 8,14
HP 7500 48-port Gig-T PoE-ready Module
min=0 \ max=2 SFP Transceivers
JD199B
See Configuration
Note:7, 8,14
DA - 13805 North America — Version 31 — March 19, 2014
Page 17
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7500 Advanced VPN Firewall Module
min=0 \ max=2 SFP Transceivers
JD249A
See Configuration
Note:13
HP 10500/11900/7500 20Gbps VPN FW Mod
min=0 \ max=2 SFP Transceivers
JG372A
See Configuration
Note:13
HP 7500 4-port 40GbE QSFP+ SC Module
min=0 \ max=4 QSFP+ Transceivers
JC792A
See Configuration
Note:10
HP 7500 4-port 40GbE CFP SC Module
min=0 \ max=4 CFP Transceivers
JG373A
See Configuration
Note:11
HP 10500/7500 20G Unified Wired-WLAN Mod
No supported Transceivers
JG639A
See Configuration
Note:15
Configuration Rules:
Note 1
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
DA - 13805 North America — Version 31 — March 19, 2014
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
Page 18
QuickSpecs
HP 7500 Switch Series
Configuration
Note 2
Note 3
Note 4
Note 5
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
The following Transceivers install into this Module: (Use #0D1or #B01 if switch is CTO)
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X240 10G SFP+ 7m Direct Attach Copper Cable
JD090A
JD091A
JD102B
JD120B
JD092A
JD093A
JD094A
JD095C
JD096C
JD097C
JG081C
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver
HP X180 10G XFP LC LH 80km 1538.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1539.77nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1540.56nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.14nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.94nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1558.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1559.79nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1560.61nm DWDM Transceiver
JD121A
JD108B
JD117B
JD107A
JG226A
JG227A
JG228A
JG229A
JG230A
JG231A
JG232A
JG233A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
DA - 13805 North America — Version 31 — March 19, 2014
Page 19
QuickSpecs
HP 7500 Switch Series
Configuration
Note 6
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver
JD118B
JD119B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD121A
JD108B
JD117B
JD107A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD100A
JD101A
Note 7
This Module is not supported on the JD242x and JD243x at this time.
Note 8
The following DIMMs install into this Module: (Use #0D1 if switch is CTO)
HP 7500 PoE DIMM Memory Module
HP 7500 24-port PoE DIMM
Note 10
JD192B
JC671A
The following 40G Transceivers install into this switch: (Use #0D1or #B01 if switch is CTO)
HP X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HP X140 40G QSFP+ MPO SR4 Transceiver
JG325A
HP X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HP X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
DA - 13805 North America — Version 31 — March 19, 2014
Page 20
QuickSpecs
HP 7500 Switch Series
Configuration
Note 11
HP X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
HP X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
HP X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG328A
JG329A
JG330A
JG331A
The following CFP Transceivers install into this switch:
HP X140 40G CFP LC LR4 10km SM Transceiver
JC857A
Note 12
The following PoE DIMM installs into this Module: (Use #0D1 if switch is CTO)
The JC671A - HP A7500 24-port PoE DIMM (must be installed to enable PoE on the these
modules)
Note 13
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
Note 14
The following PoE DIMM installs into this Module: (Use #0D1 if switch is CTO)
JD192B - HP 7500 PoE DIMM Module (must be installed to enable PoE on the these
modules)
Note 15
Maximum of this Module per Chassis:
JD238B min=0\max=9 per Chassis
JG509A min=0\max=7 per Chassis
JD239B, JD241B min=0\max=5 per Chassis
JG508A min=0\max=3 per Chassis
JD240B, JD243B min=0\max=2 per Chassis
JD242B, JG507A min=0\max=1 per Chassis
There are no restrictions on which slots these modules may go in.
Remark
JD253A - Additional User licenses available below in the 'Switch Enclosure Options'
category.
JG639A and JG645A - Additional AP licenses available below in the 'Switch Enclosure
Options' category.
JD061A
JD062A
JD063B
JD118B
JD119B
Fabric Modules
System (std 0 // max 2) User Selection (min 1 // max 2) per enclosure
See Configuration
Note:3, 12
JG507A, JG508A and JG509A only System (std 1 // max 2) User Selection (min 0 // max 1) per enclosure
See Configuration
Note:3, 12
HP 7500 384Gbps Fab Mod w/2 XFP Ports
DA - 13805 North America — Version 31 — March 19, 2014
JD193B
Page 21
QuickSpecs
HP 7500 Switch Series
Configuration
min=0 \ max=2 XFP Transceivers
See Configuration
Note:1, 4
HP 7500 384Gbps Fabric Module
No supported Transceivers
JD194B
See Configuration
Note:1
HP 7500 384Gbps Fab Mod w/12 SFP Ports
min=0 \ max=12 SFP Transceivers
JD224A
See Configuration
Note:1, 5
HP 7500 384Gbps Advanced Fabric Module
No supported Transceivers
JD195A
See Configuration
Note:1
HP 7500 384Gbps Lite Fabric Module
No supported Transceivers
JF219B
See Configuration
Note:1
HP 7500 768Gbps Fabric Module
No supported Transceivers
JD220A
See Configuration
Note:11
HP 7502 Fabric Module
No supported Transceivers
JD196A
See Configuration
Note:10
HP 7503 Fabric Module with 24 GbE Ports
min=0 \ max=24 SFP Transceivers
JD222A
See Configuration
Note:2, 5
HP A7503-S 144 Gbps Fab/MPU w 24p Gig-T
min=0 \ max=4 SFP Transceivers
JC666A
See Configuration
Note:2, 5,13
Configuration Rules:
Note 1
Note 2
These Modules install to the following switches: (Use #0D1 if switch is CTO)
HP A7503 Switch Chassis
HP A7506 Switch Chassis
HP 7506 Switch with 2 48-port Gig-T PoE+ Modules and 384Gbps MPU with 2 XFP ports
HP A7506 Vertical Switch Chassis
HP A7510 Switch Chassis
HP 7510 Switch with 2 48-port Gig-T PoE+ Modules and 768Gbps MPU
JD240x
JD239x
JG508A
JD241x
JD238x
JG509A
These Modules install to the following switches only: (Use #0D1 if switch is CTO)
HP A7503 Switch Chassis with 1 Fabric Slot
JD243x
DA - 13805 North America — Version 31 — March 19, 2014
Page 22
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7503 Switch with 48-port Gig-T PoE+ Module and 384Gbps MPU with 2 XFP ports
JG507A
Note 3
If JD243x or JG507A is selected then Max = 1.
Note 4
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver
HP X180 10G XFP LC LH 80km 1538.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1539.77nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1540.56nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.14nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.94nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1558.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1559.79nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1560.61nm DWDM Transceiver
JD121A
JD108B
JD117B
JD107A
JG226A
JG227A
JG228A
JG229A
JG230A
JG231A
JG232A
JG233A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
These Modules install to the following switches only: (Use #0D1 if switch is CTO)
HP A7502 Switch Chassis
JD242x
Note 5
Note 10
DA - 13805 North America — Version 31 — March 19, 2014
Page 23
QuickSpecs
HP 7500 Switch Series
Configuration
Note 11
These Modules install to the following switches only: (Use #0D1 if switch is CTO)
HP A7510 Switch Chassis
HP 7510 Switch with 2 48-port Gig-T PoE+ Modules and 768Gbps MPU
Note 12
If 2 Fabric Modules are selected they must be the same Sku number.
Note 13
The following PoE DIMM installs into this Module: (Use #0D1 if switch is CTO)
The JC671A - HP A7500 24-port PoE DIMM (must be installed to enable PoE on the these
modules)
Remarks:
For Switch A7503,A7506 and A7506-V, these modules can only be inserted into the Slot 0 and
Slot 1. And for Switch A7510, this module can only be inserted into the Slot 5 and Slot 6.
For Switch A7503-S, this module can only be inserted into the Slot 0.
JD238x
JG509A
A7500 PoE Module
System (std 0 // max 1) User Selection (min 0 // max 1) per Ethernet or Fabric Module
HP 7500 PoE DIMM Module
JD192B
See
Configuration
Note:1, 3, 5, 6
HP A7500 24-port PoE DIMM
JC671A
See
Configuration
Note:2, 4, 5, 6
Cofiguration Rules:
Note 1
The JD192B is optional when you have selected the JD199B, JD198B, JD210A, JC709A,
JC710A or JD228B modules.
Note 2
If this DIMM is selected at least one JD219A - HP A7500 2800W AC Power Supply is
required. (Except for JD242x, and JD243x, see rule 6)
Note 3
If 1 or more of the JD192B (PoE DIMM Module) is ordered than the customer must also
order 2 of JD208A, JD218A, JD219A, or JD227A in order to support PoE. (Except for JD242x,
and JD243x, see rule 6)
Note 4
The JC671A is optional when you have selected the JC666A, JC669A or JC668A modules.
Note 5
This Module is not supported on JG507A at this time.
Note 6
This Module is supported on the JD242x, and JD243x only when an External DC Power
Source is connected to the rear terminals. (See Installation Guide)
DA - 13805 North America — Version 31 — March 19, 2014
Page 24
QuickSpecs
HP 7500 Switch Series
Configuration
Transceivers
SFP+ Transceivers
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 5m Direct Attach Copper Cable
HP X240 10G SFP+ 7m Direct Attach Copper Cable
JD092B
JD093B
JD094B
JD095C#B01
JD096C#B01
JD097C#B01
JG081C#B01
JC784C#B01
SFP Transceivers
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm XCVR
HP X120 1G SFP LC LH40 1550nm XCVR
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X110 100M SFP LC BX 10-U Transceiver
HP X110 100M SFP LC BX 10-D Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD089B
JD118B
JD119B
JD063B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
XFP Transceivers
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC ZR 1550nm Transceiver
HP X130 10G XFP LC SR Transceiver
DA - 13805 North America — Version 31 — March 19, 2014
JD121A
JD107A
JD117B
Page 25
QuickSpecs
HP 7500 Switch Series
Configuration
HP X130 10G XFP LC LR 1310nm Transceiver
HP X180 10G XFP LC 1538.98 DWDM Xcvr
HP X180 10G XFP LC 1539.77 DWDM Xcvr
HP X180 10G XFP LC 1540.56 DWDM Xcvr
HP X180 10G XFP LC 1542.14 DWDM Xcvr
HP X180 10G XFP LC 1542.94 DWDM Xcvr
HP X180 10G XFP LC 1558.98 DWDM Xcv
HP X180 10G XFP LC 1559.79 DWDM Xcvr
HP X180 10G XFP LC 1560.61 DWDM Xcvr
JD108B
JG226A
JG227A
JG228A
JG229A
JG230A
JG231A
JG232A
JG233A
QSFP+ Transceivers
HP X140 40G QSFP+ LC LR4 SM XCVR
HP X140 40G QSFP+ MPO SR4 Transceiver
HP X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
HP X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
HP X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 1m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 3m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 5m Direct Attach Copper Cable
JG661A
JG325A
JG326A#B01
JG327A#B01
JG328A#B01
JG329A#B01
JG330A#B01
JG331A#B01
CFP Transceivers
HP X140 40G CFP LC LR4 10km SM Transceiver
JC857A
Switch Enclosure Options
Software Licenses
HP 10500/7500 Wrd-WLAN Mod 128 AP E-LTU
(min 0 // max 7)
REMARK: This license is for use with the Redundant Controllers.
JG649AAE
See
Configuration
Note:1
HP Unified Wired-WLAN 128 AP Redundant E-LTU
(min 0 // max 7)
REMARK: This license is for use with the Redundant Controllers.
JG902AAE
See
Configuration
Note:1
Configuration Rules:
Note 1
Only supported on JG639A and JG645A.
Compact Flash cards
DA - 13805 North America — Version 31 — March 19, 2014
Page 26
QuickSpecs
HP 7500 Switch Series
Configuration
System (std 0 // max 1) User Selection (min 0 // max 1)
HP X600 1G Compact Flash Card
JC684A
See
Configuration
Note:1
HP X600 512M Compact Flash Card
JC685A
See
Configuration
Note:1
HP X600 256M Compact Flash Card
JC686A
See
Configuration
Note:1
Configuration Rules:
Note 1
These CF Cards are supported on the following Modules only:
HP 7502 Fabric Module
HP 7500 384Gbps Fabric Module with 2 XFP Ports
HP 7500 384Gbps Fabric Module
HP 7500 768Gbps Fabric Module
HP 7500 384Gbps Advanced Fabric Module
HP 7500 384Gbps Lite Fabric Module
HP 7500 384Gbps Fabric Module with 12 SFP Ports
HP 7502 TAA-compliant Main Processing Unit
HP 7500 384Gbps TAA-compliant Fabric / MPU with 2 10GbE XFP Ports
HP 7500 384Gbps TAA-compliant Fabric / Main Processing Unit
HP 7500 768Gbps TAA-compliant Fabric / Main Processing Unit
HP 7503-S 144Gbps Fabric/MPU with PoE Upgradable 20-port Gig-T/4-port GbE Combo
HP 9500 VPN Firewall Module
JD196A
JD193B
JD194B
JD220A
JD195A
JF219B
JD224A
JC697A
JC699A
JC700A
JC701A
JC666A
JD245A
Options for the SSL VPN Service Board Modules (JD253x)
HP 7500 SSL VPN 1000-user License
min=0\ max=10 per SSL
JD257A
See
Configuration
Note:1
HP 7500 SSL VPN 1000-user License
min=0\ max=10 per SSL
JD257AAE
See
Configuration
Note:1
DA - 13805 North America — Version 31 — March 19, 2014
Page 27
QuickSpecs
HP 7500 Switch Series
Configuration
Configuration Rules:
Note 1
Any mixture of (JD257A) that equals 10,000 LTU's is the max per any JD253A module the maximum would be
based on the module and not the entire switch.
Options for the S1200N IPS A7500 Module (JC527A)
System (std 0 // max - no limit) User Selection (min 0 // max - no limit) per S1200N IPS A7500 Module
HP A7500 S1200N 1-y Rep DV Subsc Svc
JC592A
See
Configuration
Note:1
HP A7500 S1200N 3-y Rep DV Subsc Svc
JC593A
See
Configuration
Note:1
Configuration Rules:
Note 1
If any DV Subsc Svc is selected #0D1, it must be integrated to one of the following modules:
JC527A - HP S1200N IPS A7500 Module
Spare Fan Assembly
HP 7502 Spare Fan Assembly
HP 7503 Spare Fan Assembly
HP 7506 Spare Fan Assembly
HP 7506-V Spare Fan Assembly
HP 7510 Spare Fan Assembly
HP 7503-S Spare Fan Assembly
JD213A
JD212A
JD214A
JD215A
JD216A
JC672A
Remarks:
JD213A - This item is only used to replace the fan module of an A7502 . A host is delivered with the fan
module.
JD212A - This item is only used to replace the fan module of an A7503. A host is delivered with the fan
module.
JD214A - This item is only used to replace the fan module of an A7506. A host is delivered with the fan
module.
DA - 13805 North America — Version 31 — March 19, 2014
Page 28
QuickSpecs
HP 7500 Switch Series
Configuration
JD215A - This item is only used to replace the fan module of an A7506-V. A host is delivered with the fan
module.
JD216A - This item is only used to replace the fan module of an A7510. A host is delivered with the fan
module.
JC672A - This item is only used to replace the fan module of an A7503-S. A host is delivered with the fan
module.
DA - 13805 North America — Version 31 — March 19, 2014
Page 29
QuickSpecs
HP 7500 Switch Series
Technical Specifications
HP 7510 Switch Chassis (JD238B)
Included accessories
1 HP 7510 Spare Fan Assembly (JD216A)
Ports
2 switch fabric slots
10 I/O module slots
Supports a maximum of 84 10-GbE ports or 480 autosensing 10/100/1000 ports or 480 SFP ports, or a
combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD216A
1 fan tray slot
Power supplies
Fan tray
Physical characteristics
Memory and processor
Mounting
Performance
Dimensions
17.17(w) x 16.54(d) x 27.87(h) in (43.6 x 42.0 x 70.8 cm) (16U height)
Weight
Fabric
211 lb (95.71 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
714 million pps
Routing/Switching
capacity
1152 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 53.5 dB, High-speed fan: 56.7 dB
Electrical characteristics Description
Voltage
100-120 / 200-240 VAC
DC Voltage
-48 V / -60 V
Current
16 / 50 A
Power output
1400 W
Frequency
50 / 60 Hz
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
DA - 13805 North America — Version 31 — March 19, 2014
Page 30
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Immunity
Management
Notes
Services
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP781E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP782E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP785E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP788E)
3-year, 24x7 SW phone support, software updates (HP791E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support
(HR511E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP783E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP786E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP789E)
4-year, 24x7 SW phone support, software updates (HP792E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP784E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP787E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP790E)
5-year, 24x7 SW phone support, software updates (HP793E)
3 Yr 6 hr Call-to-Repair Onsite (HP795E)
3 Yr 6 hr Call-to-Repair Onsite (HP794E)
5 Yr 6 hr Call-to-Repair Onsite (HP796E)
DA - 13805 North America — Version 31 — March 19, 2014
Page 31
QuickSpecs
HP 7500 Switch Series
Technical Specifications
1-year, 4-hour onsite, 13x5 coverage for hardware (HR509E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR510E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR513E)
1-year, 24x7 software phone support, software updates (HR512E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 7506-V Switch Chassis (JD241B)
Included accessories
1 HP 7506-V Spare Fan Assembly (JD215A)
Ports
2 switch fabric slots
6 I/O module slots
Supports a maximum of 52 10-GbE ports or 288 autosensing 10/100/1000 ports or 288 SFP ports, or a
combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD215A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 36.61(h) in (43.6 x 42.0 x 93.0 cm) (21U height)
Power supplies
Fan tray
Physical characteristics
Weight
Memory and processor
Mounting
Performance
Fabric
222 lb (100.7 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
488 million pps
Routing/Switching
capacity
768 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 52.1 dB, High-speed fan: 56.2 dB
Electrical characteristics Description
Voltage
The H3C S7506E (HP 7506) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
100-120 / 200-240 VAC
DA - 13805 North America — Version 31 — March 19, 2014
Page 32
QuickSpecs
HP 7500 Switch Series
Technical Specifications
DC Voltage
-48 V / -60 V
Current
16 / 50 A
Power output
1400 W
Frequency
50 / 60 Hz
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
Immunity
Management
Notes
Services
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (UW999E)
3-year, 4-hour onsite, 13x5 coverage for hardware (UX001E)
3-year, 4-hour onsite, 24x7 coverage for hardware (UX004E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (UX007E)
3-year, 24x7 SW phone support, software updates (UX010E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR514E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR515E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support
(HR516E)
Installation with minimum configuration, system-based pricing (UX032E)
DA - 13805 North America — Version 31 — March 19, 2014
Page 33
QuickSpecs
HP 7500 Switch Series
Technical Specifications
4-year, 4-hour onsite, 13x5 coverage for hardware (UX002E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UX005E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX008E)
4-year, 24x7 SW phone support, software updates (UX011E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UX003E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UX006E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX009E)
5-year, 24x7 SW phone support, software updates (UX012E)
3 Yr 6 hr Call-to-Repair Onsite (UX013E)
4 Yr 6 hr Call-to-Repair Onsite (UX014E)
5 Yr 6 hr Call-to-Repair Onsite (UX015E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR518E)
1-year, 24x7 software phone support, software updates (HR517E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 7506 Switch Chassis (JD239B)
Included accessories
1 HP 7506 Spare Fan Assembly (JD214A)
Ports
2 switch fabric slots
6 I/O module slots
Supports a maximum of 52 1-GbE ports or 288 autosensing 10/100/1000 ports or 288 SFP ports, or a
combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD214A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 22.64(h) in (43.6 x 42.0 x 57.5 cm) (13U height)
Power supplies
Fan tray
Physical characteristics
Weight
Memory and processor
Mounting
Performance
Fabric
207 lb (93.9 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
488 million pps
Routing/Switching
capacity
768 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
DA - 13805 North America — Version 31 — March 19, 2014
Page 34
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 53.6 dB, High-speed fan: 57.7 dB
Electrical characteristics Achieved Miercom Certified Green Award
Description
The H3C S7506E (HP 7506) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
Voltage
100-120 / 200-240 VAC
DC Voltage
-48 V / -60 V
Current
16 / 50 A
Power output
1400 W
Frequency
50 / 60 Hz
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
Immunity
Management
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
DA - 13805 North America — Version 31 — March 19, 2014
Page 35
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Notes
Services
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (UW999E)
3-year, 4-hour onsite, 13x5 coverage for hardware (UX001E)
3-year, 4-hour onsite, 24x7 coverage for hardware (UX004E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (UX007E)
3-year, 24x7 SW phone support, software updates (UX010E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR514E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR515E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support
(HR516E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UX002E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UX005E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX008E)
4-year, 24x7 SW phone support, software updates (UX011E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UX003E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UX006E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX009E)
5-year, 24x7 SW phone support, software updates (UX012E)
3 Yr 6 hr Call-to-Repair Onsite (UX013E)
4 Yr 6 hr Call-to-Repair Onsite (UX014E)
5 Yr 6 hr Call-to-Repair Onsite (UX015E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR518E)
1-year, 24x7 software phone support, software updates (HR517E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 7503 Switch Chassis (JD240B)
Included accessories
1 HP 7503 Spare Fan Assembly (JD212A)
Ports
2 switch fabric slots
3 I/O module slots
Supports a maximum of 28 10GbE ports or 144 autosensing 10/100/1000 ports or 144 SFP ports or 12 40GbE ports, or a combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD212A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 17.36(h) in (43.6 x 42.0 x 44.1 cm) (10U height)
Power supplies
Fan tray
Physical characteristics
Weight
147 lb (66.68 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
DA - 13805 North America — Version 31 — March 19, 2014
Page 36
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Memory and processor
Mounting
Performance
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
274 million pps
Routing/Switching
capacity
480 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 51.6 dB, High-speed fan: 56.1 dB
Electrical characteristics Description
Voltage
The H3C S7506E (HP 7506) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
100-120 / 200-240 VAC
DC Voltage
-48 V / -60 V
Current
16 / 50 A
Power output
1400 W
Frequency
50 / 60 Hz
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
Immunity
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
DA - 13805 North America — Version 31 — March 19, 2014
Page 37
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP799E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP800E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP803E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP806E)
3-year, 24x7 SW phone support, software updates (HP809E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP801E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP804E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP807E)
4-year, 24x7 SW phone support, software updates (HP810E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP802E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP805E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP808E)
5-year, 24x7 SW phone support, software updates (HP811E)
3 Yr 6 hr Call-to-Repair Onsite (HP812E)
4 Yr 6 hr Call-to-Repair Onsite (HP813E)
5 Yr 6 hr Call-to-Repair Onsite (HP814E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR519E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR520E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR523E)
1-year, 24x7 software phone support, software updates (HR522E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HR521E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 7503-S Switch Chassis with 1 Fabric Slot (JD243B)
Included accessories
1 HP 7503-S Spare Fan Assembly (JC672A)
DA - 13805 North America — Version 31 — March 19, 2014
Page 38
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Ports
Power supplies
Fan tray
Physical characteristics
1 switch fabric slot
2 I/O module slots
Supports a maximum of 16 10GbE ports or 120 autosensing 10/100/1000 ports or 120 SFP ports or 8 40GbE ports, or a combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JC672A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 6.89(h) in (43.6 x 42.0 x 17.5 cm) (4U height)
Weight
Memory and processor
Mounting
Performance
Fabric
59 lb (26.76 kg), Fully loaded chassis, one fabric, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 400 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
107 million pps
Routing/Switching
capacity
144 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
High-speed fan: 56.7 dB
Electrical characteristics Description
Voltage
The H3C S7506E (HP 7506) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
100-120 / 200-240 VAC
DC Voltage
-48 V / -60 V
Current
5 / 10 A
Power output
300 W
Frequency
50 / 60 Hz
Notes
Based on a common power supply of 300 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
DA - 13805 North America — Version 31 — March 19, 2014
Page 39
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Immunity
Management
Notes
Services
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP799E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP800E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP803E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP806E)
3-year, 24x7 SW phone support, software updates (HP809E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP801E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP804E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP807E)
4-year, 24x7 SW phone support, software updates (HP810E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP802E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP805E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP808E)
5-year, 24x7 SW phone support, software updates (HP811E)
3 Yr 6 hr Call-to-Repair Onsite (HP812E)
4 Yr 6 hr Call-to-Repair Onsite (HP813E)
5 Yr 6 hr Call-to-Repair Onsite (HP814E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR519E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR520E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR523E)
1-year, 24x7 software phone support, software updates (HR522E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
DA - 13805 North America — Version 31 — March 19, 2014
Page 40
QuickSpecs
HP 7500 Switch Series
Technical Specifications
(HR521E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 7502 Switch Chassis (JD242B)
Included accessories
1 HP 7502 Spare Fan Assembly (JD213A)
Ports
2 MPU (for management modules) slots
2 I/O module slots
Supports a maximum of 16 10GbE ports or 96 autosensing 10/100/1000 ports or 96 SFP ports or 8 40-GbE
ports, or a combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD213A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 6.89(h) in (43.6 x 42.0 x 17.5 cm) (4U height)
Power supplies
Fan tray
Physical characteristics
Weight
Memory and processor
Mounting
Performance
Fabric
59 lb (26.76 kg), Fully loaded chassis, two management modules, two power
supplies, and a full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
143 million pps
Routing/Switching
capacity
192 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 49.8 dB, High-speed fan: 56.7 dB
Electrical characteristics Description
Voltage
The H3C S7506E (HP 7506) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
100-120/200-240 VAC
DC Voltage
-48 V/-60 V
Current
5/10 A
DA - 13805 North America — Version 31 — March 19, 2014
Page 41
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Power output
300 W
Frequency
50/60 Hz
Notes
Based on a common power supply 300 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
Immunity
Management
Notes
Services
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP799E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP800E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP803E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP806E)
3-year, 24x7 SW phone support, software updates (HP809E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP801E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP804E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP807E)
4-year, 24x7 SW phone support, software updates (HP810E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP802E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP805E)
DA - 13805 North America — Version 31 — March 19, 2014
Page 42
QuickSpecs
HP 7500 Switch Series
Technical Specifications
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP808E)
5-year, 24x7 SW phone support, software updates (HP811E)
3 Yr 6 hr Call-to-Repair Onsite (HP812E)
4 Yr 6 hr Call-to-Repair Onsite (HP813E)
5 Yr 6 hr Call-to-Repair Onsite (HP814E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR519E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR520E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR523E)
1-year, 24x7 software phone support, software updates (HR522E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HR521E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 7503 Switch with 48-port Gig-T PoE+ Module and 384Gbps MPU with 2 XFP ports (JG507A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
1 HP 7503 Spare Fan Assembly (JD212A)
1 HP 7500 384Gbps Fabric Module with 2 XFP Ports (JD193B)
1 HP 7500 48-port Gig-T PoE+ Extended Module (JD229B)
2 switch fabric slots
3 I/O module slots
Supports a maximum of 28 10GbE ports or 144 autosensing 10/100/1000 ports or 144 SFP ports, or a
combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD212A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 17.36(h) in (43.6 x 42.0 x 44.1 cm) (10U height)
Weight
Memory and processor
Mounting
Performance
Fabric
147 lb (66.68 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
274 million pps
Routing/Switching
capacity
480 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
DA - 13805 North America — Version 31 — March 19, 2014
Page 43
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 51.6 dB, High-speed fan: 56.1 dB
Electrical characteristics Frequency
50/60 Hz
Description
Voltage
100-120/200-240 VAC
DC Voltage
-48 to -60 VDC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
Immunity
Management
Notes
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
DA - 13805 North America — Version 31 — March 19, 2014
Page 44
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Services
Refer to the HP website at www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7506 Switch with 2 48-port Gig-T PoE+ Modules and 384Gbps MPU with 2 XFP ports (JG508A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
1 HP 7506 Spare Fan Assembly (JD214A)
2 HP 7500 48-port Gig-T PoE+ Extended Module (JD229B)
1 HP 7500 384Gbps Fabric Module with 2 XFP Ports (JD193B)
2 switch fabric slots
6 I/O module slots
Supports a maximum of 52 10GbE ports or 288 autosensing 10/100/1000 ports or 288 SFP ports, or a
combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD214A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 22.64(h) in (43.6 x 42.0 x 57.5 cm) (13U height)
Weight
Memory and processor
Mounting
Performance
Fabric
207 lb (93.9 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
488 million pps
Routing/Switching
capacity
768 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
High-speed fan: 56.7 dB
Electrical characteristics Frequency
Description
Voltage
50/60 Hz
Achieved Miercom Certified Green Award
The H3C S7506E (HP 7606) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
100-120/200-240 VAC
DA - 13805 North America — Version 31 — March 19, 2014
Page 45
QuickSpecs
HP 7500 Switch Series
Technical Specifications
DC Voltage
-48 to -60 VDC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
Immunity
Management
Notes
Services
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7510 Switch with 2 48-port Gig-T PoE+ Modules and 768Gbps MPU (JG509A)
Included accessories
2 HP 7500 48-port Gig-T PoE+ Extended Module (JD229B)
1 HP 7500 768Gbps Fabric Module (JD220A)
1 HP 7510 Spare Fan Assembly (JD216A)
DA - 13805 North America — Version 31 — March 19, 2014
Page 46
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Ports
Power supplies
Fan tray
Physical characteristics
2 switch fabric slots
10 I/O module slots
Supports a maximum of 84 10GbE ports or 480 autosensing 10/100/1000 ports or 480 SFP ports, or a
combination
2 power-supply slots
1 minimum power-supply required (ordered separately)
includes: 1 x JD216A
1 fan tray slot
Dimensions
17.17(w) x 16.54(d) x 27.87(h) in (43.6 x 42.0 x 70.8 cm) (16U height)
Weight
Memory and processor
Mounting
Performance
Fabric
211 lb (95.71 kg), Fully loaded chassis, two fabrics, two power supplies, and a
full complement of typical I/O modules
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal surface
mounting only
Throughput
714 million pps
Routing/Switching
capacity
1152 Gbps
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 95%, non-condensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, non-condensing
Acoustic
Low-speed fan: 53.5 dB, High-speed fan: 56.7 d
Electrical characteristics Frequency
50/60 Hz
Description
Voltage
100-120/200-240 VAC
DC Voltage
-48 to -60 VDC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
DA - 13805 North America — Version 31 — March 19, 2014
Page 47
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Immunity
Management
Notes
Services
Standards and protocols
(applies to all products in
series)
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
EN 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE 802.3
Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module (JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
BGP
RFC 1771 BGPv4
RFC 1772 Application of the BGP
RFC 1965 BGP4 confederations
RFC 1997 BGP Communities Attribute
RFC 1998 PPP Gandalf FZA Compression Protocol
RFC 2385 BGP Session Protection via TCP MD5
RFC 2439 BGP Route Flap Damping
RFC 2796 BGP Route Reflection
RFC 2858 BGP-4 Multi-Protocol Extensions
RFC 2918 Route Refresh Capability
RFC 3065 Autonomous System Confederations for
BGP
RFC 3392 Capabilities Advertisement with BGP-4
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4272 BGP Security Vulnerabilities Analysis
RFC 4273 Definitions of Managed Objects for
BGP-4
RFC 4274 BGP-4 Protocol Analysis
MIBs
RFC 1156 (TCP/IP MIB)
RFC 1157 A Simple Network Management Protocol
(SNMP)
RFC 1215 A Convention for Defining Traps for use
with the SNMP
RFC 1229 Interface MIB Extensions
RFC 1493 Bridge MIB
RFC 1573 SNMP MIB II
RFC 1643 Ethernet MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1757 Remote Network Monitoring MIB
RFC 1850 OSPFv2 MIB
RFC 1907 SNMPv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2096 IP Forwarding Table MIB
DA - 13805 North America — Version 31 — March 19, 2014
Page 48
QuickSpecs
HP 7500 Switch Series
Technical Specifications
RFC 4275 BGP-4 MIB Implementation Survey
RFC 4276 BGP-4 Implementation Report
RFC 4277 Experience with the BGP-4 Protocol
RFC 4360 BGP Extended Communities Attribute
RFC 4456 BGP Route Reflection: An Alternative to
Full Mesh Internal BGP (IBGP)
RFC 5291 Outbound Route Filtering Capability for
BGP-4
RFC 5292 Address-Prefix-Based Outbound Route
Filter for BGP-4
RFC 2233 Interfaces MIB
RFC 2452 IPV6-TCP-MIB
RFC 2454 IPV6-UDP-MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMPv6 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2578 Structure of Management Information
Version 2 (SMIv2)
Denial of service protection
RFC 2580 Conformance Statements for SMIv2
RFC 2618 RADIUS Client MIB
RFC 2267 Network Ingress Filtering
Automatic filtering of well-known denial-of-service RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
packets
RFC 2668 802.3 MAU MIB
CPU DoS Protection
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
Rate Limiting by ACLs
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
Device management
RFC 2925 Ping MIB
RFC 1157 SNMPv1/v2c
RFC 2933 IGMP MIB
RFC 1305 NTPv3
RFC 2934 Protocol Independent Multicast MIB for
RFC 1902 (SNMPv2)
IPv4
RFC 2271 FrameWork
RFC 3414 SNMP-User based-SM MIB
RFC 2579 (SMIv2 Text Conventions)
RFC 3415 SNMP-View based-ACM MIB
RFC 2580 (SMIv2 Conformance)
RFC 3417 Simple Network Management Protocol
RFC 2819 (RMON groups Alarm, Event, History
(SNMP) over IEEE 802 Networks
and Statistics only)
RFC 3418 MIB for SNMPv3
HTTP, SSHv1, and Telnet
RFC 3595 Textual Conventions for IPv6 Flow Label
Multiple Configuration Files
RFC 3621 Power Ethernet MIB
Multiple Software Images
RFC 3813 MPLS LSR MIB
SSHv1/SSHv2 Secure Shell
RFC 3814 MPLS FTN MIB
TACACS/TACACS+
RFC 3815 MPLS LDP MIB
Web UI
RFC 3826 AES for SNMP's USM MIB
RFC 4133 Entity MIB (Version 3)
General protocols
RFC 4444 Management Information Base for
IEEE 802.1ad Q-in-Q
Intermediate System to Intermediate System (IS-IS)
IEEE 802.1ag Service Layer OAM
IEEE 802.1p Priority
MPLS
IEEE 802.1Q VLANs
RFC 2205 Resource ReSerVation Protocol
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning Tree RFC 2209 Resource ReSerVation Protocol (RSVP)
RFC 2702 Requirements for Traffic Engineering
IEEE 802.1X PAE
Over MPLS
IEEE 802.3ab 1000BASE-T
RFC 2858 Multiprotocol Extensions for BGP-4
IEEE 802.3ac (VLAN Tagging Extension)
RFC 2961 RSVP Refresh Overhead Reduction
IEEE 802.3ad Link Aggregation Control Protocol
Extensions
(LACP)
RFC 3031 Multiprotocol Label Switching
IEEE 802.3ae 10-Gigabit Ethernet
Architecture
IEEE 802.3af Power over Ethernet
RFC 3032 MPLS Label Stack Encoding
IEEE 802.3ah Ethernet in First Mile over Point to
RFC 3107 Carrying Label Information in BGP-4
Point Fiber - EFMF
RFC 3209 RSVP-TE: Extensions to RSVP for LSP
IEEE 802.3at
DA - 13805 North America — Version 31 — March 19, 2014
Page 49
QuickSpecs
HP 7500 Switch Series
Technical Specifications
IEEE 802.3ba 40 and 100 Gigabit Ethernet
Architecture
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 894 IP over Ethernet
RFC 903 RARP
RFC 906 TFTP Bootstrap
RFC 925 Multi-LAN Address Resolution
RFC 950 Internet Standard Subnetting Procedure
RFC 951 BOOTP
RFC 959 File Transfer Protocol (FTP)
RFC 1027 Proxy ARP
RFC 1035 Domain Implementation and Specification
RFC 1042 IP Datagrams
RFC 1058 RIPv1
RFC 1142 OSI IS-IS Intra-domain Routing Protocol
RFC 1195 OSI ISIS for IP and Dual Environments
RFC 1213 Management Information Base for
Network Management of TCP/IP-based internets
RFC 1256 ICMP Router Discovery Protocol (IRDP)
RFC 1293 Inverse Address Resolution Protocol
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1393 Traceroute Using an IP Option
RFC 1519 CIDR
RFC 1531 Dynamic Host Configuration Protocol
RFC 1533 DHCP Options and BOOTP Vendor
Extensions
RFC 1591 DNS (client only)
RFC 1624 Incremental Internet Checksum
RFC 1701 Generic Routing Encapsulation
RFC 1721 RIP-2 Analysis
RFC 1723 RIP v2
RFC 1812 IPv4 Routing
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2082 RIP-2 MD5 Authentication
RFC 2091 Trigger RIP
RFC 2131 DHCP
RFC 2138 Remote Authentication Dial In User Service
(RADIUS)
RFC 2236 IGMP Snooping
RFC 2338 VRRP
RFC 2453 RIPv2
Tunnels
RFC 3212 Constraint-Based LSP Setup using LDP
RFC 3479 Fault Tolerance for the Label Distribution
Protocol (LDP)
RFC 3487 Graceful Restart Mechanism for LDP
RFC 3564 Requirements for Support of
Differentiated Service-aware MPLS Traffic
Engineering
RFC 4364 BGP/MPLS IP Virtual Private Networks
(VPNs)
RFC 4379 Detecting Multi-Protocol Label Switched
(MPLS) Data Plane Failures
RFC 4447 Pseudowire Setup and Maintenance
Using LDP
RFC 4448 Encapsulation Methods for Transport of
Ethernet over MPLS Networks
RFC 4664 Framework for Layer 2 Virtual Private
Networks
RFC 4665 Service Requirements for Layer 2
Provider Provisioned Virtual Private Networks
RFC 4761 Virtual Private LAN Service (VPLS) Using
BGP for Auto-Discovery and Signaling
RFC 4762 Virtual Private LAN Service (VPLS) Using
Label Distribution Protocol (LDP) Signaling
RFC 5036 LDP Specification
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 1155 Structure of Management Information
RFC 1157 SNMPv1
RFC 1448 Protocol Operations for version 2 of the
Simple Network Management Protocol (SNMPv2)
RFC 2211 Controlled-Load Network
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
RFC 3411 SNMP Management Frameworks
RFC 3412 SNMPv3 Message Processing
RFC 3414 SNMPv3 User-based Security Model
(USM)
RFC 3415 SNMPv3 View-based Access Control
Model VACM)
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
OSPF
RFC 1245 OSPF protocol analysis
RFC 1246 Experience with OSPF
RFC 1765 OSPF Database Overflow
RFC 1850 OSPFv2 Management Information Base
(MIB), traps
DA - 13805 North America — Version 31 — March 19, 2014
Page 50
QuickSpecs
HP 7500 Switch Series
Technical Specifications
RFC 2644 Directed Broadcast Control
RFC 2154 OSPF w/ Digital Signatures (Password,
RFC 2763 Dynamic Name-to-System ID mapping
MD-5)
support
RFC 2328 OSPFv2
RFC 2784 Generic Routing Encapsulation (GRE)
RFC 2370 OSPF Opaque LSA Option
RFC 2865 Remote Authentication Dial In User Service RFC 3101 OSPF NSSA
(RADIUS)
RFC 3137 OSPF Stub Router Advertisement
RFC 2966 Domain-wide Prefix Distribution with Two- RFC 3623 Graceful OSPF Restart
Level IS-IS
RFC 3630 Traffic Engineering Extensions to OSPFv2
RFC 2973 IS-IS Mesh Groups
RFC 4061 Benchmarking Basic OSPF Single Router
RFC 3022 Traditional IP Network Address Translator Control Plane Convergence
(Traditional NAT)
RFC 4062 OSPF Benchmarking Terminology and
RFC 3277 IS-IS Transient Blackhole Avoidance
Concepts
RFC 3567 Intermediate System to Intermediate
RFC 4063 Considerations When Using Basic OSPF
System (IS-IS) Cryptographic Authentication
Convergence Benchmarks
RFC 3719 Recommendations for Interoperable
RFC 4222 Prioritized Treatment of Specific OSPF
Networks using Intermediate System to
Version 2 Packets and Congestion Avoidance
Intermediate System (IS-IS)
RFC 4577 OSPF as the Provider/Customer Edge
RFC 3784 ISIS TE support
Protocol for BGP/MPLS IP Virtual Private Networks
RFC 3786 Extending the Number of IS-IS LSP
(VPNs)
Fragments Beyond the 256 Limit
RFC 4811 OSPF Out-of-Band LSDB
RFC 3787 Recommendations for Interoperable IP
Resynchronization
Networks using Intermediate System to
RFC 4812 OSPF Restart Signaling
Intermediate System (IS-IS)
RFC 4813 OSPF Link-Local Signaling
RFC 3847 Restart signaling for IS-IS
RFC 4940 IANA Considerations for OSPF
RFC 4251 The Secure Shell (SSH) Protocol
Architecture
QoS/CoS
RFC 4486 Subcodes for BGP Cease Notification
IEEE 802.1P (CoS)
Message
RFC 1349 Type of Service in the Internet Protocol
RFC 4884 Extended ICMP to Support Multi-Part
Suite
Messages
RFC 2211 Specification of the Controlled-Load
RFC 4941 Privacy Extensions for Stateless Address Network Element Service
Autoconfiguration in IPv6
RFC 2212 Guaranteed Quality of Service
RFC 5130 A Policy Control Mechanism in IS-IS Using RFC 2474 DSCP DiffServ
Administrative Tags
RFC 2475 DiffServ Architecture
RFC 2597 DiffServ Assured Forwarding (AF)
IP multicast
RFC 2598 DiffServ Expedited Forwarding (EF)
RFC 2236 IGMPv2
RFC 2283 Multiprotocol Extensions for BGP-4
Security
RFC 2362 PIM Sparse Mode
IEEE 802.1X Port Based Network Access Control
RFC 3376 IGMPv3
RFC 1321 The MD5 Message-Digest Algorithm
RFC 3446 Anycast Rendezvous Point (RP)
RFC 1334 PPP Authentication Protocols (PAP)
mechanism using Protocol Independent Multicast
RFC 1492 TACACS+
(PIM) and Multicast Source Discovery Protocol
RFC 1994 PPP Challenge Handshake Authentication
(MSDP)
Protocol (CHAP)
RFC 3618 Multicast Source Discovery Protocol
RFC 2082 RIP-2 MD5 Authentication
(MSDP)
RFC 2104 Keyed-Hashing for Message
RFC 3973 PIM Dense Mode
Authentication
RFC 4541 Considerations for Internet Group
RFC 2408 Internet Security Association and Key
Management Protocol (IGMP) and Multicast Listener Management Protocol (ISAKMP)
Discovery (MLD) Snooping Switches
RFC 2409 The Internet Key Exchange (IKE)
RFC 4601 Draft 10 PIM Sparse Mode
DA - 13805 North America — Version 31 — March 19, 2014
Page 51
QuickSpecs
HP 7500 Switch Series
Technical Specifications
RFC 4604 Using Internet Group Management
Protocol Version 3 (IGMPv3) and Multicast Listener
Discovery Protocol Version 2 (MLDv2) for
Source-Specific Multicast
RFC 4605 IGMP/MLD Proxying
RFC 4607 Source-Specific Multicast for IP
RFC 4610 Anycast-RP Using Protocol Independent
Multicast (PIM)
RFC 5059 Bootstrap Router (BSR) Mechanism for
Protocol Independent Multicast (PIM)
IPv6
RFC 1886 DNS Extension for IPv6
RFC 1887 IPv6 Unicast Address Allocation
Architecture
RFC 1981 IPv6 Path MTU Discovery
RFC 2080 RIPng for IPv6
RFC 2081 RIPng Protocol Applicability Statement
RFC 2292 Advanced Sockets API for IPv6
RFC 2373 IPv6 Addressing Architecture
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Auto-configuration
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2473 Generic Packet Tunneling in IPv6
RFC 2526 Reserved IPv6 Subnet Anycast Addresses
RFC 2529 Transmission of IPv6 Packets over IPv4
RFC 2545 Use of MP-BGP-4 for IPv6
RFC 2553 Basic Socket Interface Extensions for IPv6
RFC 2710 Multicast Listener Discovery (MLD) for
IPv6
RFC 2740 OSPFv3 for IPv6
RFC 2767 Dual stacks IPv46 & IPv6
RFC 2893 Transition Mechanisms for IPv6 Hosts
and Routers
RFC 3056 Connection of IPv6 Domains via IPv4
Clouds
RFC 3307 IPv6 Multicast Address Allocation
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3736 Stateless Dynamic Host Configuration
Protocol (DHCP) Service for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4214 Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP)
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 2716 PPP EAP TLS Authentication Protocol
RFC 2865 RADIUS Authentication
RFC 2866 RADIUS Accounting
RFC 2867 RADIUS Accounting Modifications for
Tunnel Protocol Support
RFC 2868 RADIUS Attributes for Tunnel Protocol
Support
RFC 2869 RADIUS Extensions
Access Control Lists (ACLs)
Guest VLAN for 802.1x
MAC Authentication
Port Security
SSHv1/SSHv2 Secure Shell
VPN
RFC 2403 - HMAC-MD5-96
RFC 2404 - HMAC-SHA1-96
RFC 2405 - DES-CBC Cipher algorithm
RFC 2407 - Domain of interpretation
RFC 2547 BGP/MPLS VPNs
RFC 2917 A Core MPLS IP VPN Architecture
RFC 3947 - Negotiation of NAT-Traversal in the IKE
RFC 4302 - IP Authentication Header (AH)
RFC 4303 - IP Encapsulating Security Payload (ESP)
IPsec
RFC 1828 IP Authentication using Keyed MD5
RFC 1829 The ESP DES-CBC Transform
RFC 2085 HMAC-MD5 IP Authentication with
Replay Prevention
RFC 2401 IP Security Architecture
RFC 2402 IP Authentication Header
RFC 2406 IP Encapsulating Security Payload
RFC 2410 - The NULL Encryption Algorithm and its
use with IPsec
RFC 2411 IP Security Document Roadmap
DA - 13805 North America — Version 31 — March 19, 2014
Page 52
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
HP 7500 48-port
100BASE-FX Module
(JD197B)
Ports
48 SFP 100BASE-FX ports (IEEE 802.3u Type 100BASE-FX); Duplex: full only
Physical characteristics
Dimensions
Services
HP 7500 48-port
10/100BASE-T Module
(JD198B)
Ports
Physical characteristics
Services
HP 7500 48-port Gig-T
PoE-ready Module
(JD199B)
Ports
Physical characteristics
Services
HP 7500 2-port 10GbE XFP Ports
Module (JD201A)
Physical characteristics
Services
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.72 lb. (3.05 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
48 RJ-45 autosensing 10/100 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3af PoE); Duplex: half or full
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.37 lb. (2.89 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
48 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3af
PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.81 lb. (3.09 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.5 lb. (2.95 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 53
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 24-port GbE SFP Ports
Module (JD203B)
Physical characteristics
Services
HP 7500 24-port Gig-T
Module (JD204B)
Ports
Physical characteristics
Services
HP 7500 24-port GbE SFP / Ports
2-port 10GbE XFP Module
(JD205A)
Physical characteristics
Services
HP 7500 12-port GbE SFP Ports
Module (JD207A)
Physical characteristics
Services
24 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.13 lb. (2.78 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6 lb. (2.72 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
24 SFP 100/1000 Mbps ports
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.5 lb. (2.95 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
12 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 1.18(w) x 1.57(h) in.
(35.5 x 3 x 4 cm)
Weight
5.86 lb. (2.66 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 54
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 24-port Gig-T / 2- Ports
port 10GbE XFP Module
(JD206A)
Physical characteristics
Services
HP 7500 48-port Gig-T
Module (JD210A)
Ports
Physical characteristics
Services
HP 7500 48-port GbE SFP Ports
Module (JD211B)
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Module with 8 Combo
Ports (JD223A)
Physical characteristics
Services
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.44 lb. (2.92 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
48 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3af
PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.81 lb. (3.09 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
48 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.7 lb. (3.04 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
16 SFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.11 lb. (2.77 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 55
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 40-port Gig-T / 8- Ports
port SFP PoE-ready
Module (JD228B)
Physical characteristics
Services
HP 7500 8-port 10G SFP+ Ports
Module (JF290A)
Physical characteristics
Notes
Services
HP 7500 20-port Gig-T / 4- Ports
port GbE Combo PoEupgradable SC Module
(JC669A)
Physical characteristics
Services
HP 7500 8-port 10GbE XFP Ports
Extended Module
Physical characteristics
(JD191A)
Services
40 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3af
PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
8 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.66 lb. (3.02 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
8 SFP+ 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.97 lb. (3.16 kg)
The module (JF290A) only support 10-GbE SFP+ transceiver, not support 1GbE
SFP transceiver.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
20 RJ-45 auto-negotiating 10/100/1000 PoE ports (IEEE 802.3 Type 10BASET, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE
802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
4 dual-personality ports; Each composed of a 10/100/1000Base-T Gigabit
Ethernet port and an SFP port, which cannot be simultaneously used
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in. (35.5 x 37.7 x 4
cm)
Weight
6.17 lb. (2.8 kg)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
8 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.12 lb. (3.23 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 56
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 48-port Gig-T
PoE+ Extended Module
(JD229B)
Ports
Physical characteristics
Services
HP 7500 24-port GbE SFP / Ports
2-port 10GbE XFP
Extended Module
(JD230A)
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Extended Module
(JD234A)
Physical characteristics
Services
HP 7500 4-port 10GbE XFP Ports
Extended Module
Physical characteristics
(JD235A)
Services
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at
PoE+); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.3 lb. (3.31 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
16 SFP 1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.79 lb. (3.08 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
16 SFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.64 lb. (3.01 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
4 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.46 lb. (2.93 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 57
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 2-port 10GbE XFP Ports
Extended Module (JD236A) Physical characteristics
Services
HP 7500 48-port GbE SFP Ports
Extended Module (JD237A) Physical characteristics
Services
HP 7500 48-port GbE SFP Ports
Enhanced Module
Physical characteristics
(JD221A)
Services
HP 7500 24-port GbE SFP Ports
Enhanced Module
(JD231A)
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Enhanced Module
(JD231A)
Physical characteristics
Services
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.46 lb. (2.93 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
48 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.16 lb. (3.25 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
48 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.16 lb. (3.25 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
16 XFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.7 lb. (3.04 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
16 XFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.7 lb. (3.04 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 58
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 2-port 10GbE XFP Ports
Enhanced Module
Physical characteristics
(JD233A)
Services
HP X124 1G SFP LC LH40
1310nm Transceiver
(JD061A)
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.46 lb. (2.93 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
Connectivity
1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1310 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
A small form-factor
cm)
pluggable SFP Gigabit LH40
Full configuration weight 0.04 lb. (0.02 kg)
transceiver that provides a
Electrical
characteristics
Power consumption typical 0.8 W
full duplex Gigabit solution
Power consumption
1.0 W
up to 40km on a singlemaximum
mode fiber.
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
Services
HP X120 1G SFP LC LH40
1550nm Transceiver
(JD062A)
40km distance
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
Connectivity
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
A small form-factor
cm)
pluggable (SFP) Gigabit
Full configuration weight 0.04 lb. (0.02 kg)
LH40 transceiver that
Electrical
characteristics
Power consumption typical 0.8 W
provides a full-duplex
Power consumption
1.0 W
Gigabit solution up to 40
maximum
km on a single mode fiber.
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
40km distance
Fiber type
Single Mode
DA - 13805 North America — Version 31 — March 19, 2014
Page 59
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP X125 1G SFP LC LH70
Transceiver (JD063B)
A small form-factor
pluggable (SFP) Gigabit
LH70 transceiver that
provides a full-duplex
Gigabit solution up to
70km on a single-mode
fiber.
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connectivity
Connector type
LC
Wavelength
1550 nm
Physical characteristics
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Electrical characteristics Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Services
HP X125 1G SFP RJ45 T
Transceiver (JD089B)
Dimensions
Maximum distance:
• 70km
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)
Connectivity
Connector type
Physical characteristics Dimensions
A small form factor
pluggable (SFP) Gigabit
Full configuration weight
1000Base-T transceiver
that provides a full duplex Electrical characteristics Power consumption
Gigabit solution up to
typical
100m on a Cat-5+ cable.
Power consumption
maximum
Cabling
RJ-45
2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4
cm)
0.07 lb. (0.03 kg)
0.8 W
1.0 W
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4pair unshielded twisted pair (UTP) or shielded twisted pair (STP) balanced,
complying with IEEE 802.3ab 1000BASE-T;
Services
Maximum distance:
• 100m
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 60
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP X120 1G SFP LC BX 10- Ports
U Transceiver (JD098B)
Connectivity
A small form-factor
Physical characteristics
pluggable (SFP) Gigabit LXBX10-U transceiver that
provides a full duplex
Gigabit solution up to
Electrical characteristics
10km on a single mode
cable.
Cabling
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Maximum distance:
• 10km
Fiber type
TX 1310nm RX 1490nm
Notes
Services
HP X120 1G SFP LC BX 10- Ports
D Transceiver (JD099B)
Connectivity
A small form-factor
Physical characteristics
pluggable (SFP) Gigabit LXBX10-D transceiver that
provides a full duplex
Gigabit solution up to
Electrical characteristics
10km on a single mode
cable.
Cabling
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Maximum distance:
• Up to 10km
Fiber type
TX 1490nm RX 1310nm
Notes
Services
Single Mode
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 61
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP X120 1G SFP LC LH100 Ports
Transceiver (JD103A)
Connectivity
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
A small form factor
pluggable (SFP) Gigabit
LH100 transceiver that
provides a full-duplex
Gigabit solution up to
100km on a single mode
fiber.
Wavelength
1550 nm
Electrical characteristics Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Services
HP X120 1G SFP LC SX
Transceiver (JD118B)
Maximum distance:
• Up to 100km
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 1000BASE-SX port
Connectivity
Connector type
LC
Wavelength
850 nm
A small form-factor
pluggable (SFP) Gigabit SX Physical characteristics Dimensions
transceiver that provides a
full-duplex Gigabit solution
Full configuration weight
up to 550m on a Multimode
Electrical characteristics Power consumption
fiber.
typical
Power consumption
maximum
Cabling
Services
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
0.04 lb. (0.02 kg)
0.8 W
1.0 W
Maximum distance:
• FDDI Grade distance = 220m
• OM1 = 275m
• OM2 = 500m
• OM3 = Not Specified by standard
Cable length
up to 550m
Fiber type
Multi Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 62
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP X120 1G SFP LC LX
Transceiver (JD119B)
Ports
1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)
Connectivity
Connector type
LC
Wavelength
1300 nm
A small form-factor
pluggable (SFP) Gigabig LX Physical characteristics
transceiver that provides a
full duplex Gigabit solution
up to 550m on MMF or
Electrical characteristics
10Km on SMF
Cabling
Cabling
Notes
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
typical
0.8 W
Power consumption
maximum
1.0 W
Cable type:
Either single mode or multimode;
Services
HP 50 m Multimode OM3
LC/LC Optical Cable
(AJ839A)
Dimensions
Maximum distance:
• 550m for Multimode
• 10km for Singlemode
Fiber type
Both
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
DA - 13805 North America — Version 31 — March 19, 2014
Page 63
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
HP 30 m Multimode OM3
LC/LC Optical Cable
(AJ838A)
Cabling
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 64
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 15 m Multimode OM3
LC/LC Optical Cable
(AJ837A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 65
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 5 m Multimode OM3
LC/LC Optical Cable
(AJ836A)
Cabling
Cable type:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: This specification defines the detail requirements for a tight
buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and
Ethernet assembly with LC duplex connectors on one end and LC duplex
connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 66
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 2 m Multimode OM3
LC/LC Optical Cable
(AJ835A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 67
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 1 m Multimode OM3
LC/LC Optical Cable
(AJ834A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 68
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 0.5 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ833A)
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm
for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber and designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 69
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 1 m PremierFlex OM3+ Notes
LC/LC Optical Cable
(BK838A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP 10500/7500 20G Unified Wired-WLAN Module (JG639A)
Ports
Physical characteristics
1 RJ-45 serial console port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type
1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
1 RJ-45 out-of-band management port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Dimensions
15.71(w) x 13.98(d) x 1.57(h) in (39.9 x 35.5 x 4.0 cm) (1U height)
Weight
7.98 lb (3.62 kg)
Memory and processor
Processor
Eight core @ 950 MHz, 1 GB compact flash, 2 GB DDR2 DIMM
Performance
Switch fabric speed
10 Gbps
MAC address table size
24000 entries
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Environment
Electrical characteristics Maximum heat
dissipation
512 BTU/hr (540.16 kJ/hr)
Maximum power rating
150 W
Notes
Power consumption: 118 W-150 W
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1; IEC 60950-1; EN 60950-1; FDA 21 CFR Subchapter J
Emissions
EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; AS/NZS CISPR 22 Class A; EN 61000-3-2; EN 610003-3; VCCI-3 CLASS A; VCCI-4 CLASS A; ETSI EN 300 386; FCC Part 15 (CFR 47) CLASS A
DA - 13805 North America — Version 31 — March 19, 2014
Page 70
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Immunity
EN
Management
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager; Telnet;
HTTPS; RMON1; FTP; in-line and out-of-band; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For use in HP 10500 Switch Series and HP 7500 Switch Series
Default supported APs: 128
Maximum supported APs: 1,024 (via the optional purchase of the 128-Access Point E-LTU)
Maximum supported users: 20,000
Maximum supported users via local portal authentication: 4,000
Maximum supported users via local authentication: 1,000
Maximum supported configured SSIDs: 512
Maximum supported ACLs: 32,000
Supported MSM APs are automatically discovered, Comware firmware is loaded, and the APs can be fully
managed.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
Features
Services
EN 55024, CISPR24 & ETSI EN 300 386
Standards and protocols
General protocols
RFC 768 UDP
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 855 Telnet Option Specification
RFC 858 Telnet Suppress Go Ahead Option
RFC 894 IP over Ethernet
RFC 950 Internet Standard Subnetting
Procedure
RFC 959 File Transfer Protocol (FTP)
RFC 1122 Host Requirements
RFC 1141 Incremental updating of the
Internet
checksum
RFC 1144 Compressing TCP/IP headers for
low-speed
serial links
RFC 1256 ICMP Router Discovery Protocol
(IRDP)
RFC 1321 The MD5 Message-Digest
Algorithm
RFC 1334 PPP Authentication Protocols
(PAP)
RFC 1350 TFTP Protocol (revision 2)
RFC 1812 IPv4 Routing
RFC 1944 Benchmarking Methodology for
Network
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Autoconfiguration
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over
Ethernet Networks
RFC 2465 Management Information Base
for IP Version
6: Textual Conventions and General
Group(partially
support, only "IPv6 Interface Statistics
table")
RFC 2466, Management Information Base
for IP Version
6 - ICMPv6
RFC 2526 Reserved IPv6 Subnet Anycast
Addresses
RFC 2553 Basic Socket Interface Extensions
for IPv6
RFC 2563 ICMPv6
RFC 2925 Definitions of Managed Objects
for Remote
Ping, Traceroute, and Lookup Operations
(Ping only)
RFC 3315 DHCPv6 (client and relay)
RFC 3363 DNS support
RFC 3484 Default Address Selection for IPv6
RFC 3493 Basic Socket Interface Extensions
for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3542 Advanced Sockets API for IPv6
RFC 3587 IPv6 Global Unicast Address
IEEE 802.11i Medium Access Control (MAC)
Security Enhancements
IEEE 802.11n WLAN Enhancements for
Higher Throughput
Note: All of the above standards are now
included in IEEE 802.11-2012
Network management
RFC 1155 Structure of Management
Information
RFC 1905 SNMPv2 Protocol Operations
RFC 2573 SNMPv3 Applications
RFC 2574 SNMPv3 User-based Security
Model (USM)
RFC 2575 VACM for SNMP
SNMPv1/v2c
QoS/CoS
RFC 2474 DS Field in the IPv4 and IPv6
Headers
RFC 2474 DSCP DiffServ
RFC 2475 DiffServ Architecture
RFC 3168 The Addition of Explicit
Congestion
Notification (ECN) to IP
WiFi MultiMedia (WMM), IEEE 802.11e
Security
IEEE 802.1X Port Based Network Access
Control
RFC 3394 Advanced Encryption Standard
(AES) Key Wrap
DA - 13805 North America — Version 31 — March 19, 2014
Page 71
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Interconnect Devices
RFC 1994 PPP Challenge Handshake
Authentication
Protocol (CHAP)
RFC 2104 HMAC: Keyed-Hashing for
Message
Authentication
RFC 2246 The TLS Protocol Version 1.0
RFC 2284 EAP over LAN
RFC 2644 Directed Broadcast Control
RFC 2864 The Inverted Stack Table
Extension to the
Interfaces Group MIB
RFC 2866 RADIUS Accounting
RFC 2869 RADIUS Extensions
RFC 3268 Advanced Encryption Standard
(AES)
Ciphersuites for Transport Layer Security
(TLS)
RFC 3619 Ethernet Automatic Protection
Switching
(EAPS)
IP multicast
RFC 1112 IGMP
RFC 2236 IGMPv2
RFC 2934 Protocol Independent Multicast
MIB for IPv4
IPv6
RFC 1350 TFTP
RFC 1881 IPv6 Address Allocation
Management
RFC 1887 IPv6 Unicast Address Allocation
Architecture
RFC 1981 IPv6 Path MTU Discovery
RFC 2292 Advanced Sockets API for IPv6
RFC 2373 IPv6 Addressing Architecture
RFC 2375 IPv6 Multicast Address
Assignments
RFC 2460 IPv6 Specification
Format
RFC 3596 DNS Extension for IPv6
RFC 4193, Unique Local IPv6 Unicast
Addresses
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
RFC 5095 Deprecation of Type 0 Routing
Headers in IPv6
MIBs
RFC 1229 Interface MIB Extensions
RFC 1643 Ethernet MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2613 SMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2932IP (Multicast Routing MIB)
RFC 2933 IGMP MIB
Algorithm
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Access Control Lists (ACLs)
Guest VLAN for 802.1x
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
Web Authentication
WPA (Wi-Fi Protected Access)/WPA2
IKEv1
RFC 3748 - Extensible Authentication
Protocol (EAP)
Mobility
IEEE 802.11a High Speed Physical Layer in
the 5 GHz Band
IEEE 802.11b Higher-Speed Physical Layer
Extension in the 2.4 GHz Band
IEEE 802.11d Global Harmonization
IEEE 802.11e QoS enhancements
IEEE 802.11g Further Higher Data Rate
Extension in the 2.4 GHz Band
IEEE 802.11h Dynamic Frequency Selection
DA - 13805 North America — Version 31 — March 19, 2014
Page 72
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 Access Controller Module (JD440A)
Ports
Physical characteristics
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
2 USB 1.0 12 Mbps ports
Dimensions
14.45(d) x 13.39(w) x 1.6(h) in. (36.7 x 34 x 4.06 cm) (1U height)
Weight
7.28 lb. (3.3 kg)
Memory and processor
Processor
Eight core @ 950 MHz, 256 MB compact flash, 1 GB DDR2 DIMM
Performance
Switch fabric speed
20 Gbps
MAC address table size
24000 entries
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Environment
Electrical characteristics Maximum heat
dissipation
Maximum power rating
Safety
Emissions
Immunity
Management
Features
Notes
Services
Standards and protocols
273 BTU/hr (288.02 kJ/hr)
80 W
UL 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; GOST; C-Tick; NOM; IEC 60950-1(with CB
report)
EN 55022; VCCI; ICES-003; AS/NZS CISPR 22; EN 300 386; FCC Part 15; EN 61000-3-2:2006; EN 61000-33:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC
EN
EN 61000-4-2:1995+A1:1998+A2:2001; EN 61000-4-3:2006; EN 61000-44:2004; EN 61000-4-5:2006; EN 61000-4-6: 1996 +A1:2001:A2:2007; EN
61000-4-8:2001; EN 61000-4-11:2004; EN 55024:1998+ A1:2001 + A2:2003
IMC - Intelligent Management Center; command-line interface; Web browser; configuration menu; SNMP
Manager; Telnet; HTTPS; RMON1; FTP; in-line and out-of-band; IEEE 802.3 Ethernet MIB; Ethernet
Interface MIB
A7500 ACM License system
- The A7500 ACM is an access controller module for the HP A7500 series Ethernet switches. It supports 128
APs by default. After license upgrade, the access controller module can support up to 640 APs.
Max. number of users: 20K. Max. number of users that are supported by local authentication: 1K. Max.
number of SSIDs that can be configured: 512. Max. number of users that are supported by local portal
authentication: 4K. Number of ACLs: 32K.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
General protocols
RFC 768 UDP
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
MIBs
RFC 1229 Interface MIB Extensions
RFC 1643 Ethernet MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
DA - 13805 North America — Version 31 — March 19, 2014
Page 73
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
RFC 855 Telnet Option Specification
RFC 858 Telnet Suppress Go Ahead Option
RFC 894 IP over Ethernet
RFC 950 Internet Standard Subnetting Procedure
RFC 959 File Transfer Protocol (FTP)
RFC 1122 Host Requirements
RFC 1141 Incremental updating of the Internet
checksum
RFC 1144 Compressing TCP/IP headers for
low-speed serial links
RFC 1256 ICMP Router Discovery Protocol (IRDP)
RFC 1321 The MD5 Message-Digest Algorithm
RFC 1334 PPP Authentication Protocols (PAP)
RFC 1350 TFTP Protocol (revision 2)
RFC 1812 IPv4 Routing
RFC 1944 Benchmarking Methodology for Network
Interconnect Devices
RFC 1994 PPP Challenge Handshake Authentication
Protocol (CHAP)
RFC 2104 HMAC: Keyed-Hashing for Message
Authentication
RFC 2246 The TLS Protocol Version 1.0
RFC 2284 EAP over LAN
RFC 2644 Directed Broadcast Control
RFC 2864 The Inverted Stack Table Extension to the
Interfaces Group MIB
RFC 2866 RADIUS Accounting
RFC 2869 RADIUS Extensions
RFC 3268 Advanced Encryption Standard (AES)
Ciphersuites for Transport Layer Security (TLS)
RFC 3619 Ethernet Automatic Protection Switching
(EAPS)
IP multicast
RFC 1112 IGMP
RFC 2236 IGMPv2
RFC 2934 Protocol Independent Multicast MIB for
IPv4
IPv6
RFC 1350 TFTP
RFC 1881 IPv6 Address Allocation Management
RFC 1887 IPv6 Unicast Address Allocation
Architecture
RFC 1981 IPv6 Path MTU Discovery
RFC 2292 Advanced Sockets API for IPv6
RFC 2373 IPv6 Addressing Architecture
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Auto-configuration
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2613 SMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2933 IGMP MIB
Mobility
IEEE 802.11a High Speed Physical Layer in the 5
GHz Band
IEEE 802.11b Higher-Speed Physical Layer
Extension in the 2.4 GHz Band
IEEE 802.11d Global Harmonization
IEEE 802.11g Further Higher Data Rate Extension in
the 2.4 GHz Band
IEEE 802.11i Medium Access Control (MAC)
Security Enhancements
IEEE 802.11n WLAN Enhancements for Higher
Throughput
Network management
RFC 1155 Structure of Management Information
RFC 1905 SNMPv2 Protocol Operations
RFC 2573 SNMPv3 Applications
RFC 2574 SNMPv3 User-based Security Model
(USM)
RFC 2575 VACM for SNMP
SNMPv1/v2c
QoS/CoS
RFC 2474 DS Field in the IPv4 and IPv6 Headers
RFC 2474 DSCP DiffServ
RFC 2475 DiffServ Architecture
RFC 3168 The Addition of Explicit Congestion
Notification (ECN) to IP
WiFi MultiMedia (WMM), IEEE 802.11e
Security
IEEE 802.1X Port Based Network Access Control
RFC 3394 Advanced Encryption Standard (AES)
Key Wrap Algorithm
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Access Control Lists (ACLs)
Guest VLAN for 802.1x
Secure Sockets Layer (SSL)
SSHv1.5 Secure Shell
SSHv2 Secure Shell
Web Authentication
WPA (Wi-Fi Protected Access)/WPA2
DA - 13805 North America — Version 31 — March 19, 2014
Page 74
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
IKEv1
RFC 2463 ICMPv6
RFC 3748 - Extensible Authentication Protocol (EAP)
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2526 Reserved IPv6 Subnet Anycast Addresses
RFC 2563 ICMPv6
RFC 2925 Definitions of Managed Objects for
Remote Ping, Traceroute, and Lookup Operations
(Ping only)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 5095 Deprecation of Type 0 Routing Headers
in IPv6
HP TippingPoint S1200N
IPS A7500 Module
(JC527A)
Ports
2 SFP 1000 Mbps ports
2 RJ-45 1000 Mbps ports
1 Compact Flash port
1 RJ-45 serial console port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Physical characteristics Dimensions
13.7(d) x 15.7(w) x 1.6(h) in. (34.8 x 39.88 x 4.06
cm)
Weight
7.7 lb. (3.49 kg), Fully loaded
Electrical characteristics Throughput
up to 1.3 Gbps
IPS/IDS throughput
1.3 Gbps inspected throughput
Concurrent sessions
6,500,000
New sessions/second
78K
Environment
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, noncondensing
humidity
Nonoperating/Storage
-20°F to 45°F (-28.9°C to 7.2°C)
temperature
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Standards and protocols Denial of service
Automatic filtering of well-known denial-ofservice
protection
packets
Rate Limiting by ACLs
IPv6
RFC 2460 IPv6 Specification
DA - 13805 North America — Version 31 — March 19, 2014
Page 75
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 384Gbps Fabric
Module with 2 XFP Ports
(JD193B)
Ports
Physical characteristics
HP 7500 384Gbps Fabric
Module (JD194B)
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x 4.5
cm)
Weight
7.94 lb. (3.6 kg)
Physical characteristics
HP 7500 384Gbps
Advanced Fabric Module
(JD195A)
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x 4.5
cm)
Weight
7.94 lb. (3.6 kg)
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x 4.5
cm)
Weight
7.94 lb. (3.6 kg)
Physical characteristics
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 76
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 768Gbps Fabric
Module (JD220A)
Ports
Physical characteristics
Services
HP 7500 1400W DC Power Physical characteristics
Supply (JD208A)
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x 4.5
cm)
Weight
7.85 lb. (3.56 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Dimensions
Weight
Electrical characteristics Voltage
7.72(w) x 14.06(d) x 5.04(h) in (19.6 x 35.7 x 12.8
cm) (3U height)
20.39 lb (9.25 kg)
0~-48/-60V
Current
0/50 A
Idle power
168 W
Maximum power rating
1400 W
PoE power
140 W
Notes
Services
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 77
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 1400W AC Power Physical characteristics
Supply (JD218A)
Dimensions
Weight
Electrical characteristics Voltage
7.72(w) x 14.06(d) x 5.04(h) in (19.6 x 35.7 x 12.8
cm) (3U height)
14 lb (6.35 kg)
100-120/200-240 VAC
Current
0/16 A
Idle power
196 W
Maximum power rating
1400 W
PoE power
0W
Frequency
50/60 Hz
Notes
Notes
Services
HP 7500 6000W AC Power Physical characteristics
Supply (JD227A)
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
1400W AC Power Supply uses a 16-A AC power
cable
US order needs to indicate either #ABA option (for 110V) or #B2E (for 220V).
This will determine which power cord the distribution centres include with the
product.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Dimensions
Weight
Electrical characteristics Voltage
7.72(w) x 14.06(d) x 5.04(h) in (19.6 x 35.7 x 12.8
cm) (3U height)
28.22 lb (12.8 kg)
100-120/200-240 VAC
Current
0/16 A
Idle power
105 W
Maximum power rating
6000 W
PoE power
5300 W
Frequency
50/60 Hz
Notes
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged
in, and all modules populated.
6000W AC Power Supply uses a 16-A AC power
cable.
DA - 13805 North America — Version 31 — March 19, 2014
Page 78
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Notes
Services
HP 7503 Fabric Module
with 24 GbE Ports
(JD222A)
Ports
Physical characteristics
Services
HP 7503-S 144 Gbps Fabric Ports
/ Main Processing Unit
with PoE-upgradable 20p
Gig-T / 4p GbE Combo
(JC666A)
Physical characteristics
Services
US order needs to indicate either #ABA option (for 110V) or #B2E (for 220V).
This will determine which power cord the distribution centres include with the
product.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
16 SFP 100/1000 Mbps ports
8 dual-personality ports; Combo ports (RJ45 or SFP)
Dimensions
14.84(w) x 13.98(d) x 1.77(h) in
(37.7 x 35.5 x 4.5 cm)
Weight
6.17 lb (2.8 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 RJ-45 serial console port; One console port, used for local or remote
configuration and management of the switch through a dialup connection
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
20 RJ-45 auto-negotiating 10/100/1000 PoE ports (IEEE 802.3 Type 10BASET, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE
802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
4 dual-personality ports; each of which consists of a 10/100/1000Base-T port
and an SFP port. The two ports comprising a Combo port cannot operate at
the same time.
Dimensions
13.98(w) x 14.84(d) x 1.77(h) in (35.51 x 37.69 x
4.5 cm)
Weight
6.31 lb (2.86 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 79
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7503-S 144 Gbps TAA Ports
Fabric/Main Processing
Unit with 16 GbE SFP Ports
and 8 GbE Combo Ports
(JC698A)
Physical characteristics
Services
HP 7500 650W AC Power
Supply (JD217A)
Physical characteristics
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
16 SFP 100/1000 Mbps ports
8 dual-personality ports; Combo ports (RJ45 or SFP)
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x 4.5
cm)
Weight
6.17 lb. (2.8 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Dimensions
Weight
Electrical characteristics Voltage
5.51(w) x 13.78(d) x 1.57(h) in (14 x 35 x 4 cm) (1U
height)
5.34 lb (2.42 kg)
100-120/200-240 VAC
Current
0/10 A
Idle power
97.5 W
Maximum power rating
650 W
PoE power
0W
Frequency
50/60 Hz
Notes
Services
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged
in, and all modules populated.
650W AC Power Supply uses a 10-A AC power
cable
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 80
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7500 650W DC Power
Supply (JD209A)
Physical characteristics
Dimensions
Weight
Electrical characteristics Voltage
5.51(w) x 13.78(d) x 1.57(h) in (14 x 35 x 4 cm) (1U
height)
4.96 lb (2.25 kg)
0~-48/-60V
Current
0/25 A
Idle power
97.5 W
Maximum power rating
650 W
PoE power
0W
Notes
Services
HP 7502 300W AC Power
Supply (JD226A)
Physical characteristics
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged
in, and all modules populated.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Dimensions
Weight
Electrical characteristics Voltage
5.51(w) x 13.78(d) x 1.57(h) in (14 x 35 x 4 cm) (1U
height)
4.17 lb (1.89 kg)
100-120/200-240 VAC
Current
0/5 A
Idle power
54 W
Maximum power rating
300 W
PoE power
0W
Frequency
50/60 Hz
Notes
Services
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged
in, and all modules populated.
300W AC Power Supply uses a 10-A AC power
cable
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13805 North America — Version 31 — March 19, 2014
Page 81
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 7502 Fabric Module
(JD196A)
Ports
Physical characteristics
Services
HP 7502 TAA-compliant
Main Processing Unit
(JC697A)
Ports
Physical characteristics
Services
HP 7500 4-port 40GbE
Physical characteristics
QSFP+ SC Module (JC792A)
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
7.83(w) x 13.98(d) x 1.77(h) in
(19.9 x 35.5 x 4.5 cm)
Weight
2.98 lb. (1.35 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 7.83(w) x 1.77(h) in. (35.5 x 19.9 x 4.5
cm)
Weight
2.98 lb. (1.35 kg)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Dimensions
Weight
Services
HP 7500 4-port 40GbE CFP Physical characteristics
SC Module (JG373A)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Dimensions
Weight
Services
10.08(w) x 11.73(d) x 1.57(h) in (25.6 x 29.8 x 4
cm)
6.88 lb (3.12 kg)
16.77(w) x 11.73(d) x 1.57(h) in (42.6 x 29.8 x 4
cm)
7.63 lb (3.46 kg))
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
To learn more, visit: www.hp.com/networking
© Copyright 2010-2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or
editorial errors or omissions contained herein.
DA - 13805 North America — Version 31 — March 19, 2014
Page 82
Download PDF
Similar pages