OP7K-DC0-xx-CF
Data sheet
Features
„
Compliant with XFP MSA
„
Wavelength selectable to C-band ITU-T grid
wavelengths
„
Suitable for use in 100GHz channel spacing DWDM
systems
„
No Reference Clock required
„
Cold Start up Wavelength Compliance
„
DWDM-rated EML transmitter and APD receiver
„
link length up to 120km (with amplifier)
„
Low Power Dissipation 3.5W Maximum
„
RoHS Compliant
Applications
„
SONET OC-192&SDH STM 64
„
Ethernet (10GBASE and 10G BASE with FEC)
„
DWDM Networks
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage
Optical Input Received Power
Symbol
Min.
Max.
Units
Tst
−40
85
°C
Vcc2
-0.5
+2.0
V
Vcc3.3
-0.5
+4.0
V
VCC5.0
-0.5
+6.0
V
APD-IN
---
-8
dBm
Remarks
Operating Conditions
Parameter
Operating Case temperature
Supply Voltage
Supply Current
Module Power Dissipation
Symbol
Min.
Typ.
Max.
Units
Tca
-5
-
70
ºC
Vcc1.8
1.71
1.8
1.89
V
Vcc3.3
3.13
3.3
3.47
V
Vcc5.0
4.75
5.0
5.25
V
Icc2
-
-
750
mA
Icc3.3
-
-
750
mA
Icc5.0
-
-
500
mA
-
3.5
W
Pm
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Remarks
Date: Jan. 2, 2013
Version: B
Page 1 of 9
OP7K-DC0-xx-CF
Data sheet
Transmitter Electro-optical Characteristics
Vcc = 3.13 V to 3.47 V, TC = -5 °C to 70 °C
Parameter
Symbol
Optical Transmit Power
Min.
Typ.
Max.
Units
+2
dBm
Note
Po
-2
PTX_DIS
---
---
-30
dBm
Extinction Ratio
ER
9
---
---
dB
Center Wavelength-Start of Life
λC
λC-25
λC
λC+25
pm
1
Center Wavelength-End of Life
λC
λC-100
λC
λC+100
pm
1
Side-mode Supression Ratio
SMSR
30
---
---
dB
Jitter Generation (P-P)
JG P-P
---
---
0.1
UI
Jitter Generation (RMS)
JG RMS
---
---
0.01
UI
Spectral Width (-20dB)
Δλ20
---
---
0.3
nm
Dispersion Penalty with 2400 ps/nm
DP
---
---
2.0
dB
Relative Intensity Noise
RIN
---
---
-130
dB/Hz
Optical Transmit Power (disabled)
Optical Output Eye
Compliant with ITU-T G.691 STM-64 eye mask
Input Differential impedance
Rim
---
VtxDIFF
120
850
mV
Transmit Disable Voltage
VD
2.0
Vcc3+0.3
V
Transmit Enable Voltage
Ven
0
+0.8
V
Transmit Disable Assert Time
Vn
---
10
us
Differential data Input
2
100
Ω
---
Note:
1. Wavelength stability is achieved within 60 seconds (max) of power up.
2. BER=10^-12; PRBS 2^31-1@9.95Gbps
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 2 of 9
OP7K-DC0-xx-CF
Data sheet
Receiver Electro-optical Characteristics
Vcc = 3.13 V to 3.47 V, TC = -5 °C to 70 °C
Parameter
Maximum Input Power
Symbol
Min.
Typ.
Max.
Units
RX-overload
-7
---
---
dBm
λ
1528
---
1565
nm
Rrx
---
---
-27
dB
Loss of Signal Asserted
LOS_A
-34
---
---
dBm
LOS De-Asserted
LOS_D
---
---
-24
dBm
LOS Hysteresis
LOS_H
0.5
---
---
dB
Rom
---
100
---
Ω
Vout P-P
350
---
850
mV
Rise/Fall Time (20%~80%)
Tr/Tf
24
---
---
ps
Loss of Signal-Asserted
VOH
2
---
Vcc3+0.3-
V
Loss of Signal-Negated
VOL
GND
---
GND+0.5
V
Min.
Typ.
Input Operating Wavelength
Reflectance
Output differential impedance
Differential Output Swing
Note
Reference Clock
Parameter
Clock Differential Input Impedance
Symbol
Max.
Units
CI
80
100
120
Ω
Differential Input Amplitude (p-p)
DCA
640-
---
1600
mV
Reference Clock Duty Cycle
RCY
40
---
60
%
Reference Clock Rise/Fall Time
Tr / Tf
200
---
1250
ps
fu
---
Baud/64
---
MHz
Reference Clock Frequency
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Note
20%~80%
Date: Jan. 2, 2013
Version: B
Page 3 of 9
OP7K-DC0-xx-CF
Data sheet
C-band λc Wavelength Guide
Channels
Frequency
Wavelength
Channels Frequency Wavelength
Channels Frequency Wavelength
17
191.7
1563.86
32
193.2
1551.72
47
194.7
1539.77
18
191.8
1563.05
33
193.3
1550.92
48
194.8
1538.98
19
191.9
1562.23
34
193.4
1550.12
49
194.9
1538.19
20
192.0
1561.42
35
193.5
1549.32
50
195.0
1537.40
21
192.1
1560.61
36
193.6
1548.51
51
195.1
1536.61
22
192.2
1559.79
37
193.7
1547.72
52
195.2
1535.82
23
192.3
1558.98
38
193.8
1546.92
53
195.3
1535.04
24
192.4
1558.17
39
193.9
1546.12
54
195.4
1534.25
25
192.5
1557.36
40
194.0
1545.32
55
195.5
1533.47
26
192.6
1556.55
41
194.1
1544.53
56
195.6
1532.68
27
192.7
1555.75
42
194.2
1543.73
57
195.7
1531.9
28
192.8
1554.94
43
194.3
1542.94
58
195.8
1531.12
29
192.9
1554.13
44
194.4
1542.14
59
195.9
1530.33
30
193.0
1553.33
45
194.5
1541.35
60
196.0
1529.55
31
193.1
1552.52
46
194.6
1540.56
61
196.1
1528.77
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 4 of 9
OP7K-DC0-xx-CF
Data sheet
Pin Assignment
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 5 of 9
OP7K-DC0-xx-CF
Data sheet
Pin Description
Pin
1
2
Logic
3
LVTTL-I
4
LVTTL-O
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
LVTTL-I
LVTTL-I/O
LVTTL-I/O
LVTTL-O
LVTTL-O
LVTTL-O
CML-O
CML-O
Symbol
GND
VEE5
Mod_DeSel
Name/Description
Note
1
Module Ground
Optional -5.2V Power Supply – Not required
Module De-select; When held low allows module to respond to 2-wire
serial interface commands.
Interrupt; Indicates presence of an important condition which can be read
Interrupt
TX_DIS
VCC5
GND
VCC3
VCC3
SCL
SDA
Mod_Abs
Mod_NR
RX_LOS
GND
GND
RDRD+
GND
VCC2
over the 2-wire serial interface
2
Transmitter Disable; Turns off transmitter laser output
+5V Power Supply
1
Module Ground
+3.3V Power Supply
+3.3V Power Supply
2-Wire Serial Interface Clock
2-Wire Serial Interface Data Line
Module Absent; Indicates Module is not present. Grounded in the Module
Module Not Ready
Receiver Loss of Signal Indicator
Module Ground
Module Ground
2
2
2
2
2
1
1
Receiver Inverted Data Output
Receiver Non-Inverted Data Output
1
Module Ground
+1.8V Power Supply
Power down; When high, requires the module to limit power consumption
to 1.5W or below, 2-Wire serial interface must be functional in the low
21
LVTTL-I
P_Down/RST
power mode.
Reset; The falling edge initiates a complete reset of the module including
the 2-wire serial interface, equivalent to a power cycle.
22
23
VCC2
GND
24
PECL-I
RefCLK+
25
PECL-I
RefCLK-
+1.8V Power Supply
1
Module Ground
Reference Clock non-inverted input, AC coupled on the host board-Not
required.
Reference Clock inverted input, AC coupled on the host board- Not
required
3
3
26
GND
Module Ground
1
27
GND
Module Ground
1
28
CML-I
TDTransmitter Inverted Data Input
29
CML-I
TD+
Transmitter Non-Inverted Data Input
30
GND
Module Ground
1
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector; should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.
3. A Reference Clock input is not required.
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 6 of 9
OP7K-DC0-xx-CF
Data sheet
Dimensions
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 7 of 9
OP7K-DC0-xx-CF
Data sheet
Optical Receptacle Cleaning Recommendations :
All fiber stubs inside the receptacle portions were cleaned before shipment. In the event of
contamination of the optical ports, the recommended cleaning process is the use of forced
nitrogen. If contamination is thought to have remained, the optical ports can be cleaned using a
NTT international Cletop® stick type and HFE7100 cleaning fluid. Before the mating of
patch-cord, the fiber end should be cleaned up by using Cletop® cleaning cassette.
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 8 of 9
OP7K-DC0-xx-CF
Data sheet
Ordering Information
OP 6 C
- S 10 - 13 - C M
Product Code:
Data Rate:
Type:
Reach:
Wavelength:
Operating Temperature:
Additional Feature:
5=GBIC;
A=155Mb/s;
S=Single-mode;
Normal:
Normal:
C=Commercial Purpose
M=Digital Optical Monitoring
6=SFP-LC;
B=622Mb/s;
M=Multi-mode;
X1=Under 150m;
85=850nm;
C=1.25Gb/s;
W=BWDM;
X3=300m;
13=1310nm;
7=XFP;
C=CWDM;
8=XENPAK;
D=2.125Gb/s;
9=X2;
E=2.5Gb/s;
A=SFP+;
F=4.25Gb/s;
C=QSFP;
G=3.1Gb/s;
P=SFP-SC;
J=2.97G
G=GPON ONU;
A0=100km;
Q=SFP-MTRJ
P=6.144G:
H=GPON OLT
C0=120km
X5=550m;
D=DWDM;
T=Copper-T (RJ-45)
E=GEPON ONU;
F=GEPON OLT;
02=2km,
10=10km;
70=70km;
Q=7.37G;
CWDM:
H=8.5Gb/s;
20=20dB;
K=10Gb/s;
24=24dB;
R=20Gb/s;
28=28dB
S=40Gb/s;
15=1550nm;
00=Copper T (RJ-45)
(DOM)
(0~70℃);
I= Industrial Purpose
(Extended Range)
(RX_LOS for Copper TX);
F=with Fiber Stub;
I=with Isolator;
S=Customized Style
CWDM:
27=1270nm;
47=1470nm;
61=1610nm
BWDM:
B3=Tx1310/Rx1550; B5=Tx1550/Rx1310;
B4=Tx1310/Rx1490; B9=Tx1490/Rx1310;
51=Tx1510/Rx1570; 57=Tx1570/Rx1510;
27=Tx1270/Rx1330; 33=Tx1330/Rx1270;
B2=Tx1270/Rx1577; B7=Tx1577/Rx1270
M=100Base-X SGMII;
T2=2TX1310nm; T3=TX1310nm;
N=100/1000Base-X SGMII;
T5=TX1550nm
DWDM:
17=Channel 17
34= Channel 34
Model Number
Part Number
XFP-DWDM-120 OP7K-DC0-xx-CF
Input/Output
Signal Detect
Voltage
Temprature
AC/AC
TTL
3.3/5V
-5°C to 70 °C
Note: xx = channels
Note: All information contained in this document is subject to change without notice.
Optech Technology Co., Ltd.
2F., No.41, Ln. 221, Gangqian Rd., Neihu Dist., Taipei City 114, Taiwan, R.O.C.
Tel: +886-2-2656-0588
Fax: +886-2-2656-0599
http://www.optech.com.tw
e-mail: sales@optech.com.tw
Date: Jan. 2, 2013
Version: B
Page 9 of 9
Download PDF
Similar pages