Industrial Motherboard
EMB-H110B
E11482
First Edition
May 2016
Copyright Notice
This document is copyrighted, 2016. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products described
in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of the original
manufacturer. Information provided in this manual is intended to be accurate and
reliable. However, the original manufacturer assumes no responsibility for its use,
or for any infringements upon the rights of third parties that may result from its use.
The material in this document is for product information only and is subject to
change without notice. While reasonable efforts have been made in the preparation
of this document to assure its accuracy, the original manufacturer assumes no
liabilities resulting from errors or omissions in this document, or from the use of the
information contained herein.
The original manufacturer reserves the right to make changes in the product
design without notice to its users.
Acknowledgments
All other products’ name or trademarks are properties of their respective owners.
•
AMI is a trademark of American Megatrends Inc.
•
Intel®, Core™ are trademarks of Intel® Corporation.
•
Microsoft Windows® is a registered trademark of Microsoft Corp.
•
IBM, PC/AT, PS/2, and VGA are trademarks of International Business
Machines Corporation.
The original manufacturer reserves the right to make changes in the product
design without notice to its users.
All other product names or trademarks are properties of their respective owners.
ii
Contents
Chapter 1
1.1
Product overview
Package contents......................................................................... 1-1
1.2Features......................................................................................... 1-1
1.3Specifications................................................................................ 1-2
Chapter 2
Motherboard information
2.1
Before you proceed...................................................................... 2-1
2.2
Motherboard layout....................................................................... 2-2
2.3
Screw size...................................................................................... 2-4
2.4
2.5
2.3.1
Component side............................................................... 2-4
2.3.2
Solder side....................................................................... 2-5
Central Processing Unit (CPU).................................................... 2-6
2.4.1
Installing the CPU............................................................ 2-7
2.4.2
CPU heatsink and fan assembly installation.................... 2-9
System memory.......................................................................... 2-11
2.5.1
Installing a DIMM........................................................... 2-11
2.6Jumpers....................................................................................... 2-12
2.7Connectors.................................................................................. 2-15
2.8
2.7.1
Rear panel connectors................................................... 2-15
2.7.2
Internal connectors........................................................ 2-16
Power Supply Considerations................................................... 2-26
Chapter 3
3.1
3.2
3.3
BIOS setup
BIOS setup program..................................................................... 3-1
3.1.1
BIOS menu screen........................................................... 3-2
3.1.2
Menu bar.......................................................................... 3-2
Main menu..................................................................................... 3-2
3.2.1
System Date [Day MM/DD/YYYY]................................... 3-2
3.2.2
System Time [HH:MM:SS]............................................... 3-2
Advanced menu............................................................................ 3-2
3.3.1
CPU Configuration........................................................... 3-2
3.3.2
SATA Configuration......................................................... 3-3
3.3.3
USB Configuration........................................................... 3-3
3.3.4
PCH-FW Configuration.................................................... 3-4
3.3.5
SIO Configuration............................................................ 3-4
iii
3.4
3.5
3.6
3.3.6
Hardware Monitor............................................................ 3-5
3.3.7
Power Management......................................................... 3-7
3.3.7
Digital IO Port Configuration............................................ 3-8
Chipset menu................................................................................ 3-9
3.4.1
System Agent (SA) Configuration.................................... 3-9
3.4.2
PCH-IO Configuration.................................................... 3-10
Security menu............................................................................. 3-10
3.5.1
Administrator Password................................................. 3-10
3.5.2
User Password............................................................... 3-10
Boot menu................................................................................... 3-11
Boot Configuration........................................................................ 3-11
3.7
Save & Exit menu........................................................................ 3-12
Appendix
Notices........................................................................................................A-1
iv
Chapter 1
Product overview
1.1
Package contents
Check your industrial motherboard package for the following items.
1 x Industrial Motherboard
1 x SATA cable
1 x SATA power cable
1 x I/O Shield
1 x Support CD
NOTE: If any of the above items is damaged or missing, contact your
distributor or sales representative immediately.
1.2Features
•
Intel® Socket 1151 for 6th Generation Core™ i7/Core™ i5 / Core™ i3, Pentium®
and CeleronTM Processors up to 65W
•
Two 260-pin Dual Channel DDR4 2133/1867MHz SO-DIMMs up to 32GB
•
2 x SATA 6.0 Gb/s, 4 x USB3.0, 6 x USB2.0, 2 x COM header
•
1 x PCI Express 2.0 [x1]
•
1 x Full/Half-size Mini card ( default: mSATA) (PCIe +USB optional)
•
1 x Half-size Mini card
•
Multi Display: HDMI, (DP optional by BOM change), LVDS, eDP
Chapter 1: General information
1-1
1.3Specifications
SYSTEM
CPU
LGA1151 socket for Intel® 6th Generation Core™ i7 / Core™ i5 /
Core™ i3, Pentium® / Celeron® processors
Supports Intel® CPU Max. 65W TDPs
Chipset
Memory
Intel® H110 Express Chipset
2 x SO-DIMM, max. 32GB, non-ECC DDR4 2133 / 1867 MHz
Dual-channel memory architecture
Graphics
I/O Chipset
Storage
Ethernet
Audio
TPM
Expansion slots
Intel® HD Graphics
NCT6791D
2 x SATA 6Gb/s
2 x Realtek® 8111G PCIe Gigabit LAN
Realtek® ALC887 with Amp.
Infineon SLB96XX TT 1.2/2.0 (default: No)
1 x PCI Express 2.0 [x1] slot (Gen 2)
1 x Half size Mini Card (PCIe +USB)
1 x Full/Half size Mini Card (default: mSATA) (PCIe +USB optional)
BIOS
H/W Monitor
64Mbit Flash ROM, AMI BIOS
Temperature monitor on CPU/Chassis
Voltage Monitor on Vcore/5V/12V
Fan Monitor on CPU/Chassis
Watchdog Timer
Wake on LAN
Smart Fan Control
Power State
1~255 steps by software program
Graphics Chipset
Intel HD Graphics
Graphics MultiDisplay
HDMI
2HDMI+LVDS, 2HDMI+eDP, HDMI+LVDS+eDP; both 2HDMI
coulbe be replaced with DP by BOM change
DisplayPort
Up to 4096 x 2160 @ 24 Hz / 3840 x 2160 @ 60 Hz, with Digital
Audio
LVDS/eDP
LVDS Up to 1920 x 1200 @60 Hz, Dual Channel 18/24 bit,
Yes (WOL / PXE) (PXE only support with LAN1)
CPU Fan(3.3V PWM control) / Chassis Fan
S3, S4, S5
GRAPHICS
®
Up to 4096 x 2160 @ 24 Hz / 2560 x 1600 @ 60 Hz, with Digital
Audio
eDP UP to 4096 x 2340 @ 60Hz
Backlight Control
Voltage / PWM
(continued on the next page)
1-2
EMB-H110B
I/O
Storage
2 x SATA 6Gb/s
1 x Full size Mini Card (SATA 6Gb/s)
4 pin SATA power (5V, 12V @1A)
USB
4 x USB 3.0 ports (4 ports in Rear IO)
6 x USB 2.0 ports (4 ports at mid board, 2 port for mini card)
Display I/O
Audio I/O
1 x LVDS, 1 x eDP, 2 x HDMI (DP optional by BOM change)
LAN I/O
Serial port
2 x RJ-45
Mic-in, Line-out, AAFP at internal connector for 2 additional channel
(default Line-out, Mic-in), speaker
1 x RS-232 (mid board)
1 x RS-232/422/485 supports 5V/12V/RI option (mid board)
DIO
FAN
8-bit Digital I/O interface (4-in/4-out)
1 x CPU Fan connector (4-pin)
1 x Chassis Fan connector (4-pin)
ENVIRONMENT, POWER, & ME
Battery
Lithium battery
Power requirement
DC input: +12 (± 5%) VDC
Back Panel DC jack (5.5/2.5mm)
4-pin internal power connector
NOTE: Please use fixed voltage power supply.
Operating
Temperature
Operating Humidity
0~60°C
0% ~ 90%RH, non-condensing
Certificate
CE & FCC (Class A)
Form Factor
Mini ITX Form Factor, 6.7”x 6.7” (170mmx170mm)
Weight
1.1 lb (0.5 Kg)
PLACEMENT
Back I/O ports
1 x DC Jack
1 x HDMI / DP (HDMI and DP colay; default: HDMI)
1 x HDMI / DP (HDMI and DP colay; default: HDMI)
2 x LAN (RJ45)
4 x USB 3.0
1 x Audio jacks (Mic-In) pink connector
1 x Audio jacks (Line-Out) green connector
(continued on the next page)
Chapter 1: General information
1-3
PLACEMENT
Internal I/O
connectors
1 x PCIe[x1] Slot
1 x Full/Half-size Mini Card slot
2 x SATA 6Gb/s
2 x USB 2.0 connectors support additional 4 USB ports (2.00 mm)
2 x boxer header for COM (COM1: RS-232/422/485 supports
5V/12V/RI; COM2: RS-232)
1 x LVDS connector (Top side)
1 x eDP connector (Bottom side)
1 x Panel 3.3V /5V jumper
1 x Panel backlight DC / PWM mode jumper
1 x Panel backlight connector (inverter)
1 x Panel backlight 12V /5V jumper
1 x Digital I/O box header
1 x 4 PIN (2x2) internal power connector
1 x 4 PIN CPU Fan connector
1 x 4 PIN Chassis Fan connector
1 x Front Panel connector
1 x AAFP
1 x Speaker for 2W/4Ω
1 x Chassis Intrusion follow ASUS pin out
1 x Buzzer on board (Pin Header)
1 x AT/ATX mode select jumper
1 x clear CMOS jumper
OTHERS
OS Support
Windows 7 32 bit / 64 bit
®
Windows® 8 32 bit / 64 bit
Windows® 10 64 bit
Linux Fedora
Accessories
1 x SATA cable
1 x SATA power cable
I/O Shield
Support DVD
NOTE: Specifications are subject to change without notice.
1-4
EMB-H110B
Chapter 2
Motherboard information
2.1
Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
CAUTION!
•
Unplug the power cord from the wall socket before touching any
component.
•
Before handling components, use a grounded wrist strap or touch a safely
grounded object or a metal object, such as the power supply case, to avoid
damaging them due to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
•
Before you install or remove any component, always remove the AC power
by unplugging the power cord from the power outlet. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
Standby Power LED
The motherboard comes with a standby power LED that lights up to indicate that
the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you
should shut down the system and unplug the power cable before removing or
plugging in any motherboard component. The illustration below shows the location
of the onboard LED.
LED_5V
LED_5VSUS
ON
OFF
ON
Main Power Main Power Off Standby Power
OFF
Powered Off
EMB-H110B
EMB-H110B Onboard LEDs
Chapter 2: Motherboard information
2-1
2.2
Motherboard layout
NOTE: Place four screws into the holes indicated by circles to secure the
motherboard to the chassis.
CAUTION! Do not overtighten the screws! Doing so can damage the
motherboard.
1
2
3
4
5
6 7
8
9
17.0cm(6.7in)
SATA6G_1 SATA6G_2
LJ3
COM_V COM1 COM2
DIO
EATX_PWR2
18
DP2
or
HDMI2
11
12
13
CLRTC
25
14
15
USB3_34
CHASSIS
Intel®
H110
LAN1
RTL
8111G
LGA1151
SATA_PWR
16
LAN2
24
BATTERY_H
MIC-IN
AAFP
AMP_CON
MINICARD1
RT3607CE
LED_+5V
LED_+5VSUS
LINE-OUT
17.0cm(6.7in)
Place this side
towards the rear
of the chassis
DDR4 DIMM_A1 (64bit, 260-pin module)
BIOS_P
USB56 USB78
10
LJ1
INV
DDR4 DIMM_B1 (64bit, 260-pin module)
128Mb
BIOS
26
Super
I/O
LVDS
MINICARD2
DP1
or
HDMI1
USB3_12
LJ2
CH7511
BOTTOM:EDP
CHA_FAN1 CPU_FAN1
EATX_PWR1
ALC
887
SPEAKER
PCIEX1_1
F_PANEL
EMB-H110B
23 22 21
2-2
20 19
18
17
EMB-H110B
Connectors/Jumpers/Slots
1. EATX power connector (4-pin EATX_PWR2)
2. CPU and chassis fan connectors (4-pin CPU_FAN1, 4-pin CHA_FAN1)
3. Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1/2)
4. COM1 Ring/+5V/+12V selection (COM1_V)
Page
2-24
2-17
2-19
2-13
5.
Serial port connectors (10-pin COM1, COM2)
2-23
6.
Digital I/O connector (10-pin DIO)
2-18
7.
DDR4 SO-DIMM slots
2-11
8.
Inverter Backlight Control mode selection (3-pin LJ3)
2-14
9.
Inverter voltage selection (3-pin LJ2)
2-13
10. LVDS panel voltage selection (3-pin LJ1)
2-13
11.
12.
13.
14.
15.
16.
17.
18.
2-22
2-24
2-17
2-12
2-18
2-6
2-22
2-20
19.
20.
21.
22.
23.
24.
25.
26.
Backlight inverter power connector (5-pin INV)
Embedded DisplayPort (40-pin EDP)
LVDS connector (40-pin LVDS)
Clear RTC RAM (CLRTC)
Chassis intrusion connector (4-1 pin CHASSIS)
Intel® LGA1151 CPU socket
SPI flash programmable connector (8-pin BIOS_P)
Full / Half size Mini Card (mSATA) (MINICARD2)
Half size Mini Card (PCIe+USB) (MINICARD1)
Front panel system panel connector (10-1 pin F_PANEL)
Speaker connector (4-pin SPEAKER)
Standby power LEDs (LED_+5V, LED_+5VSUS)
Battery connector (2-pin BATTERY_H)
Audio amplifier connector (4-pin AMP_CON)
Front panel audio connector (10-1 pin AAFP)
SATA power connector (4-pin SATA_PWR)
USB 2.0 connectors (10-pin USB56, USB78)
Chapter 2: Motherboard information
2-19
2-20
2-1
2-22
2-16
2-25
2-16
2-21
2-3
2-4
2.3
Screw size
2.3.1
Component side
EMB-H110B
2.3.2
Solder side
Chapter 2: Motherboard information
2-5
2.4
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA1151 socket designed for
the Intel® 6th Generation Core™ i7 / Core™ i5 / Core™ i3, Pentium® / Celeron®
processors.
EMB-H110B
EMB-H110B CPU socket LGA1151
IMPORTANT: Unplug all power cables before installing the CPU.
CAUTION!
2-6
•
Upon purchase of the motherboard, ensure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the
PnP cap/socket contacts/motherboard components. The manufacturer will
shoulder the cost of repair only if the damage is shipment/transit-related.
•
Keep the cap after installing the motherboard. The manufacturer will
process Return Merchandise Authorization (RMA) requests only if the
motherboard comes with the cap on the LGA1151 socket.
•
The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
EMB-H110B
2.4.1
Installing the CPU
1
A
B
2
3
CAUTION! LGA1156 CPU is not compatible with the LGA1151 socket. DO
NOT install an LGA1156 CPU on the LGA1151 socket.
Chapter 2: Motherboard information
2-7
4
C
A
B
5
2-8
EMB-H110B
2.4.2
CPU heatsink and fan assembly installation
CAUTION! Apply the Thermal
Interface Material to the CPU
heatsink and CPU before you
install the heatsink and fan if
necessary.
To install the CPU heatsink and fan assembly
A
1
B
2
B
A
3
Chapter 2: Motherboard information
4
2-9
To uninstall the CPU heatsink and fan assembly
1
2
A
B
B
A
2-10
EMB-H110B
2.5
System memory
This motherboard comes with two Double Data Rate 4 (DDR4) Small Outline Dual Inline
Memory Module (SO-DIMM) sockets. The figure below illustrates the location of the DDR4
SO-DIMM sockets:
Channel
DIMM_B1
DIMM_A1
Sockets
Channel A
SO-DIMM_A1
Channel B
SO-DIMM_B1
EMB-H110B
EMB-H110B 260-pin DDR4 SO-DIMM sockets
2.5.1
Installing a DIMM
To install a DIMM
3
To remove a DIMM
3
Chapter 2: Motherboard information
2-11
2.6Jumpers
1.
Clear RTC RAM (CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of system setup parameters by erasing
the CMOS RTC RAM data. The onboard button cell battery powers the RAM
data in CMOS, which include system setup information such as system
passwords.
2
1
2
3
CLRTC1
RTC Batt.
(Default)
Clear CMOS
EMB-H110B
EMB-H110B Clear RTC RAM
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on
pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup
to reenter data.
CAUTION! Except when clearing the RTC RAM, never remove the cap on
CLRTC jumper default position. Removing the cap will cause system boot
failure!
NOTES:
2-12
•
If the steps above do not help, remove the onboard battery and move the
jumper again to clear the CMOS RTC RAM data. After clearing the CMOS,
reinstall the battery.
•
You do not need to clear the RTC when the system hangs due to
overclocking. For system failure due to overclocking, use the CPU
Parameter Recall (C.P.R) feature. Shut down and reboot the system so the
BIOS can automatically reset parameter settings to default values.
EMB-H110B
2.
COM1 Ring/+5V/+12V selection (COM1_VSET)
1 2
3 4
5 6
COM_V
+12V
+5V
Ring
(Default)
EMB-H110B
EMB-H110B COM1 Ring/+5V/+12V Selection
3.
Setting
Pins
+12V
1-2
+5V
3-4
Ring (Default)
5-6
LVDS panel voltage selection (3-pin LJ1)
1
2
2
3
LJ1
+5V
+3.3V
(Default)
EMB-H110B
EMB-H110B LVDS Panel Voltage Selection
Pins
4.
+5V
1-2
+3.3V (Default)
2-3
Inverter voltage selection (3-pin LJ2)
LJ2
1
2
2
3
DC CTL PWM CTL
(Default)
EMB-H110B
EMB-H110B Inverter Voltage Selection
Pins
DC Voltage Control (Default)
1-2
PWM Control
2-3
Chapter 2: Motherboard information
2-13
5.
Inverter Backlight Control mode selection (3-pin LJ3)
LJ3
1
2
+12V
2
3
+5V
(Default)
EMB-H110B
EMB-H110B Mode Selection for Back
Light Control of Inverter
Pins
2-14
+12V
1-2
5V (Default)
2-3
EMB-H110B
2.7Connectors
2.7.1
Rear panel connectors
1
2
3
4
5
6
1.
DC-In power jack. This jack connects to a DC power adapter.
2.
HDMI ports. These ports are for High-Definition Multimedia Interface (HDMI),
and are HDCP compliant, allowing playback of HD DVD, Blu-ray, and other
protected content.
3.
USB 3.0 ports. These 9-pin Universal Serial Bus (USB) ports connect to
USB 3.0/2.0 devices.
NOTES:
4.
•
DO NOT connect a keyboard / mouse to any USB 3.0 port when installing
Windows® operating system.
•
Due to USB 3.0 controller limitation, USB 3.0 devices can only be used
under Windows® OS environment and after the USB 3.0 driver installation.
•
We strongly recommend that you connect USB 3.0 devices to USB 3.0
ports for faster and better performance for your USB 3.0 devices.
LAN (RJ-45) ports. These ports allow Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
LAN port LED indications
ACT/LINK LED
Status
Description
OFF
No link
GREEN
Linked
BLINKING
Data activity
Chapter 2: Motherboard information
SPEED LED
Status
Description
OFF
10 Mbps
connection
ORANGE 100 Mbps
connection
GREEN
1 Gbps
connection
Activity Link
LED
Speed
LED
LAN port
2-15
5.
Line Out port (green). This port connects to a headphone or a speaker. In a
4-channel, 6-channel and 8-channel configurations, the function of this port
becomes Front Speaker Out.
6.
Microphone port (pink). This port connects a microphone.
NOTE: Refer to the audio configuration table for the function of the audio ports
in the 2, 4, 6, or 8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Headset
4-channel
2-channel
Pink (Rear panel) Mic In
Mic In
Front
Green (Rear panel) Line Out
Speaker Out
Port
2.7.2
1.
6-channel
8-channel
Bass/Center
Front Speaker
Out
Bass/Center
Front Speaker Out
Internal connectors
SATA power connector (4-pin SATA_PWR)
This connector is for the SATA power cable. The power cable plug is
designed to fit this connector in only one orientation. Find the proper
orientation and push down firmly until the connector completely fit.
SATA_PWR
PIN 1
+12V
GND
GND
+5V
EMB-H110B
EMB-H110B SATA POWER connector
2.
Audio amplfier connector (4-pin AMP_CON)

This connector is for an internal stereo amplifier speakers support (2W/4
via WtoB header).
AMP_CON
ROUTP
ROUTN
LOUTN
LOUTP
PIN 1
EMB-H110B
EMB-H110B Audio Stereo
Output with Amp connector
2-16
EMB-H110B
3.
CPU and chassis fan connectors (4-pin CPU_FAN1, 4-pin CHA_FAN1)
Connect the fan cables to the fan connectors on the motherboard, ensuring
that the black wire of each cable matches the ground pin of the connector.
CHA_FAN1 CPU_FAN1
PIN 1
PWM
SENSE
VCC
GND
PWM
SENSE
VCC
GND
PIN 1
EMB-H110B
EMB-H110B Fan connectors
CAUTION: Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the fan
connectors!
NOTE: The CPU_FAN connector supports a CPU fan of maximum 2A (24 W)
fan power.
4.
LVDS connector (40-pin LVDS)
This connector is for an LCD monitor that supports Low Voltage Differential
Signalling (LVDS) interface.
LVDS
PIN 40
SPD1
NC
+BLVCC
+BLVCC
+BLVCC
LVDS1_CLKLVDS1_CLK+
VCON
INV_ENABKL
SPC1
GND
GND
GND
LVDS0_CLKLVDS0_CLK+
GND
GND
GND
+3V
NC
+V_PANEL
+V_PANEL
+V_PANEL
GND
LVDS1_D0LVDS1_D0+
LVDS1_D1LVDS1_D1+
LVDS1_D2LVDS1_D2+
LVDS1_D3LVDS1_D3+
LVDS0_D0LVDS0_D0+
LVDS0_D1LVDS0_D1+
LVDS0_D2LVDS0_D2+
LVDS0_D3LVDS0_D3+
EMB-H110B
PIN 1
EMB-H110B LVDS connector
Chapter 2: Motherboard information
2-17
5.
Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch.
Connect one end of the chassis intrusion sensor or switch cable to this
connector. The chassis intrusion sensor or switch sends a high-level signal to
this connector when a chassis component is removed or replaced. The signal
is then generated as a chassis intrusion event.
By default, the pins labeled “Intruder” are shorted with a jumper cap. Remove
the jumper caps only when you intend to use the chassis intrusion detection
feature.
CHASSIS
Intrudor
Intrudor
No Intrudor
PIN1
EMB-H110B
EMB-H110B Chassis intrusion connector
6.
Digital I/0 connector (10-pin DIO)
This connector includes 8 I/O lines (In/Out programmable). All of the Digital
I/O lines are programmable and each I/O pin can be individually programmed
to support various devices.
PIN 1
DIO_I#1
DIO_P#3
DIO_O#1
DIO_O#3
+5V
DIO_I#2
DIO_I#4
DIO_O#2
DIO_O#4
GND
DIO
EMB-H110B
EMB-H110B DIO connector
NOTE: To configure the I/O pins in BIOS, go to the Advanced tab > Dynamic
Digital IO. See section 3.3.2 Dynamic Digital IO for details.
2-18
EMB-H110B
7.
Front panel system panel connector (10-1 pin F_PANEL)
This connector supports several chassis-mounted functions.
F_PANEL
PWR_LED+
PWR_LEDPWRBTN#
GND
+PWR LED PWR BTN
HDD_LED+
HDD_LEDGND
RSTCON#_PANEL
(NC)
PIN 1
+HDD_LED
RESET
EMB-H110B
EMB-H110B System panel connector
•
System power LED (2-pin +PWR_LED)
•
This 2-pin connector is for the system power LED. Connect the chassis
power LED cable to this connector. The system power LED lights up when
you turn on the system power, and blinks when the system is in sleep mode.
Hard disk drive activity LED (2-pin +HDD_LED)
•
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity
LED cable to this connector. The IDE LED lights up or flashes when data is
read from or written to the HDD.
ATX power button/soft-off button (2-pin PWR_BTN)
•
This 2-pin connector is for the system power button.
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
Chapter 2: Motherboard information
2-19
8.
Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1/2)
SATA6G_1
SATA6G_2
GND
RSATA_RXP1
RSATA_RXN1
GND
RSATA_TXN1
RSATA_TXP1
GND
GND
RSATA_RXP2
RSATA_RXN2
GND
RSATA_TXN2
RSATA_TXP2
GND
These connector connects to Serial ATA 6.0 Gb/s hard disk drives or an
optical drive via Serial ATA 6.0 Gb/s signal cables.
EMB-H110B
EMB-H110B SATA 6.0Gb/s connectors
NOTE: You must install Windows® 7 or later version before using Serial ATA
hard disk drives.
9.
Speaker connector (4-pin SPEAKER)
The 4-pin connector is for the chassis-mounted system warning speaker. The speaker
allows you to hear system beeps and warnings.
+5V
GND
GND
SPKO
SPEAKER
EMB-H110B
PIN 1
EMB-H110B SPEAKER connector
10. Minicard connectors
Use these connectors to connect a Minicard device.
MINICARD2
MINICARD1
EMB-H110B
EMB-H110B MINICARD connectors
NOTE: The Minicard device is purchased separately.
2-20
EMB-H110B
11. USB 2.0 connectors (10-pin USB56, USB78)
These connectors are for USB 2.0 ports. Connect the USB cable to these
connectors. These USB connectors comply with USB 2.0 specification that
supports up to 480 Mbps connection speed.
PIN 1
+5V
S_USB_PN
S_USB_PP
GND
GND
EMB-H110B
+5V
S_USB_PN
S_USB_PP
GND
GND
PIN 1
GND
GND
S_USB_PP
S_USB_PN
+5V
USB78
GND
GND
S_USB_PP
S_USB_PN
+5V
USB56
EMB-H110B USB2.0 connectors
CAUTION! Never connect a 1394 cable to the USB connector. Doing so will
damage the motherboard.
NOTE: The USB cable is purchased separately.
IMPORTANT!
•
Before you install Windows® 7, go to the Advanced tab of the BIOS Setup
program and configure the following items: XHCI mode [Disabled] and
USB (EHCI support) [Enabled]. You can re-configure these BIOS items
after the Windows® 7 installation.
•
You can download the Intel-released XHCI Driver Creator Utility for
Windows 7 from: https://downloadcenter.intel.com/download/25476/
Windows-7-USB-3-0-Creator-Utility
Installing Windows® 7 in Skylake platform
1.
Use the Windows® 7 XHCI Driver Creator Utility to pack the XHCI driver
into the original Windows 7 OS image. A new Windows 7 OS image will be
created.
2.
Use the new OS image to install Windows® 7.
Chapter 2: Motherboard information
2-21
12. SPI Flash programmable connector (8-pin BIOS_P)
This connector is for SPI flash program machine. Connect the flash BIOS
cable to this connector.
BIOS_P
PIN 1
+3V_SPI
S_SPI_CS1#Q
S_SPI_MISO_2Q
(NC)
GND
S_SPI_CLK_2Q
S_SPI_MOSI_2Q
(NC)
EMB-H110B
EMB-H110B SPI programming connector
NOTE: The flash BIOS cable is purchased separately.
13. Battery connector (2-pin BATTERY_H)
This connector is for the lithium CMOS battery.
BATTERY_H
GND
+BAT
PIN 1
EMB-H110B
EMB-H110B Battery Holder connector
14.Backlight inverter power connector (5-pin INV)
Connect the backlight inverter power cable to this connector. INV1
BLDN#_R
BLUP#_R
GND
GND
+BLVCC
+BLVCC
VCON
INV_ENABKL
PIN1
EMB-H110B
EMB-H110B Inverter connector
NOTE: The backlight inverter power cable and the inverter module are
purchased separately.
2-22
EMB-H110B
15. Serial port connectors (10-pin COM1, COM2)
These connectors are for serial (COM) ports. Connect the serial port cables
to these connectors, then install the module to a slot opening at the back of
the system chassis.
PIN 1
NC
CTS
DSR
DTR
RXD
PIN 1
RI_F_VCC
RTS
GND
TXD
DCD
COM2
NC
CTS1
DSR1
DTR1
RXD1
RI1_F_VCC
RTS1
GND
TXD
DCD
COM1
EMB-H110B
EMB-H110B Serial port connectors
Pin
Signal
Pin
Signal
1
DCD (422TXD-/485DATA-)
2
RXD (422RXD+)
3
TXD (422TXD+/485DATA+)
4
DTR (422RXD-)
5
GND
6
DSR
7
RTS
8
CTS
9
RI/+12V/+5V
10
N.C.
NOTES:
•
The serial port cables are purchased separately.
•
Only COM1 can support RS-422 and RS-485.
Chapter 2: Motherboard information
2-23
16. EATX power connector (4-pin EATX_PWR2)
This connector is for EATX power supply plug. The power supply plug
is designed to fit this connector in only one orientation. Find the proper
orientation and push down firmly until the connector completely fit.
DC_IN
DC_IN
EATX_PWR2
GND
GND
PIN 1
EMB-H110B
EMB-H110B 1 x 4 PIN (2x2)
internal power connector
17. Embedded DisplayPort (40-pin EDP)
This connector is for an internal embedded DisplayPort connection.
EDP
PIN 1
EMB-H110B
NC
GND
eDP_TXN3_C
eDP_TXP3_C
GND
eDP_TXN2_C
eDP_TXP2_C
GND
eDP_TXN1_C
eDP_TXP1_C
GND
eDP_TXN0_C
eDP_TXP0_C
GND
eDP_AUXP_C
eDP_AUXN_C
GND
+V_PANEL
+V_PANEL
+V_PANEL
+V_PANEL
NC
GND
GND
GND
GND
eDP_HPD_RRR
GND
GND
GND
GND
BKLTEN_R
BKLTCTL_R
NC
NC
+BLVCC
+BLVCC
+BLVCC
+BLVCC
NC
PIN 40
EMB-H110B Embedded DisplayPort
2-24
EMB-H110B
18. Front panel audio connector (10-1 pin AAFP)
NC
AGND
NC
NC
SENSE2_RETUR
AGND
NC
SENSE1_RETUR
This connector is for a chassis-mounted front panel audio I/O module that
supports either HD Audio or legacy AC`97 audio standard. Connect one end
of the front panel audio I/O module cable to this connector.
AAFP
PORT1 L
PORT1 R
PORT2 R
SENSE_SEND
PORT2 L
MIC2
MICPWR
Line out_R
NC
Line out_L
PIN 1
PIN 1
HD-audio-compliant
Legacy AC’97
pin definition
compliant pin definition
EMB-H110B
EMB-H110B Front panel audio connector
IMPORTANT!
•
We recommend that you connect a high-definition front panel audio
module to this connector to avail of the motherboard’s high-definition audio
capability.
•
If you want to connect a high-definition front panel audio module to this
connector, set the Front Panel Type item in the BIOS setup to [HD]; if you
want to connect an AC’97 front panel audio module to this connector, set
the item to [AC97]. By default, this connector is set to [HD].
Chapter 2: Motherboard information
2-25
2.8
Power Supply Considerations
CAUTION!
2-26
•
The external DC jack (5.5/2.5mm) is the primary power input connector of
EMB-H110B. However, the desktop board also provides an internal 2 x 2
power connector that can be used in custom-developed systems that have
an internal power supply.
•
There is no isolation circuitry between the external DC jack and the internal
2 x 2 power connector. It is the system integrator’s responsibility to ensure
no more than one power supply unit is or can be attached to the board at
any time and to ensure the external DC jack is covered if the internal 2 x 2 power connector is to be used.
•
Simultaneous connection of both external and internal power supply units
could result in potential damage to the desktop board, power supplies, or
other hardware.
•
System power requirements will depend on actual system configurations
chosen by the integrator, as well as end user expansion preferences. It
is the system integrator’s responsibility to ensure an appropriate power
budget for the system configuration is properly assessed based on the
system-level components chosen.
•
Considering the power conversion efficiency between Vin (+12V), the Vout
(+12V) output voltage is set around 11.6V.
EMB-H110B
Chapter 3
BIOS setup
3.1
BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its parameters. The
BIOS screens include navigation keys and brief online help to guide you in using
the BIOS Setup program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
Press <Delete> during the Power-On Self Test (POST). If you do not press
<Delete>, POST continues with its routine.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
•
Press <Ctrl>+<Alt>+<Del> simultaneously.
•
Press the reset button on the system chassis.
•
Press the power button to turn the system off then back on. Do this option only
if you failed to enter BIOS Setup using the first two options.
NOTE: Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys
to reboot a running operating system can cause damage to your data or system.
Always shut down the system properly from the operating system.
IMPORTANT:
•
The default BIOS settings for this motherboard apply to most working
conditions and ensures optimal performance. If the system becomes
unstable after changing any BIOS settings, load the default settings to
regain system stability. Select the option Restore Defaults under the Save
& Exit Menu. See section 3.7 Save & Exit.
•
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
Chapter 3: BIOS setup
3-1
3.1.1
BIOS menu screen
3.1.2
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration.
Advanced
For changing the advanced system settings.
Chipset
For viewing and changing chipset settings.
Security
For setting up BIOS security settings.
Boot
For changing the system boot configuration.
Save & Exit
For selecting the exit options and loading default settings.
To select an item on the menu bar, press the right or left arrow key on the
keyboard until the desired item is highlighted.
3.2
Main menu
The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
3.2.1
System Date [Day MM/DD/YYYY]
Allows you to set the system date.
3.2.2
System Time [HH:MM:SS]
Allows you to set the system time.
3.3
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other
system devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect
field values can cause the system to malfunction.
Case Open Warning [Disabled]
Allows you to enable or disable case open warning function. Configuration options:
[Disabled] [Enabled] [Clear]
3.3.1
CPU Configuration
The items in this menu show CPU-related information the BIOS automatically
detects.
The items shown in the submenu may be different depending on the type of
CPU installed.
3-2
EMB-H110B
Hyper-threading [Enabled]
The Intel Hyper-Threading Technology allows a hyper-threading processor to
appear as two logical processors to the operating system, allowing the operating
system to schedule two threads or processes simultaneously.
[Enabled]
Two threads per activated core are enabled.
[Disabled]
Only one thread per activated core is enabled.
Configuration options for active processor cores are dependent on the installed
CPU.
Intel Virtualization Technology [Enabled]
[Enabled]
Allows a hardware platform to run multiple operating
systems separately and simultaneously, enabling one
system to virtually function as several systems.
Disables this function.
[Disabled]
3.3.2
SATA Configuration
The BIOS automatically detects the presence of SATA devices. The Serial ATA
Ports listed will display Empty if there are no Serial devices connected to the ports.
Serial ATA Port 0, 1, 3
Port 0, 1, 3 [Enabled]
These items become configurable when you set the SATA Mode Selection
item to [AHCI] and [RAID], and allow you to enable/disable the SATA port(s).
Configuration options: [Disabled] [Enabled]
Hot Plug [Disabled]
These items become configurable when you set the SATA Mode Selection item
to [AHCI] and [RAID], and allow you to enable/disable SATA Hot Plug Support.
Configuration options: [Disabled] [Enabled]
3.3.3
USB Configuration
The USB Devices item lists auto-detected values. If no USB device is detected,
the item shows None.
Legacy USB Support [Enabled]
[Enabled]Enables the support for USB devices on legacy operating
systems (OS).
[Disabled]
USB devices are only available when running BIOS Setup.
[Auto]Allows the system to detect the presence of USB devices
at startup. If detected, the USB controller legacy mode is
enabled. If no USB device is detected, the legacy USB support
is disabled.
Chapter 3: BIOS setup
3-3
XHCI Hand-off [Enabled]
[Enabled]
Enables the support for operating systems without an XHCI hand‑off
feature.
[Disabled]
Disables the XHCI Hand-off support.
3.3.4
PCH-FW Configuration
Firmware Update Configuration
Me FW Image Re-Flash [Disabled]
This item allows you to enable or disable Me FW Image Re-Flash function.
Configuration options: [Disabled] [Enabled]
Local FW Update [Enabled]
This item allows you to enable or disable the local FW update function.
Configuration options: [Disabled] [Enabled]
3.3.5
SIO Configuration
The items in this menu allow you to configure Super IO settings.
[*Active*] Serial Port 1
Use this device [Enabled]
Allows you to enable or disable this logical device. Configuration options:
[Enabled] [Disabled]
The following two items appear only when you set Use this device to
[Enabled].
Possible [Use Automatic Settings]
Allows you to select an optimal setting for Super I/O devices. Configuration
options: [Use Automatic Settings] [IO=3F8h; IRQ=4;] [IO=2F8h; IRQ=3]
Mode [RS-232]
Allows you to select the Serial Port mode. Configuration options: [RS-232]
[RS-422] [RS-485]
[*Active*] Serial Port 2
Use this device [Enabled]
Allows you to enable or disable this logical device. Configuration options:
[Enabled] [Disabled]
3-4
EMB-H110B
Possible [Use Automatic Settings]
This item appears only when you set Use this device to [Enabled] and
allows you to select an optimal setting for Super I/O devices. Configuration
options: [Use Automatic Settings] [IO=2F8h; IRQ=3] [IO=3F8h; IRQ=4;]
3.3.6
Hardware Monitor
The items in this menu allow you to configure the smart fan.
Smart Fan Configuration
CPU Smart Fan Control [Enabled]
Allows you to enable or disable CPU Smart Fan Control. Configuration options:
[Enabled] [Disabled]
The following sub-items appear only when you set CPU Smart Fan Control to
[Enabled].
Fan Control Mode [SMART FAN IV Mode]
Select fan control mode. Configuration options: [Manual Mode] [Thermal
Cruise Mode] [SMART FAN IV Mode]
The following 6 items appear only when you set Fan Control Mode to [Smart
FAN IV Mode].
Temperature source [PECI Agent 0]
Allows you to select the temperature source. Configuration
options: [SYSTIN] [CPUTIN] [AUXTIN0] [AUXTIN1] ~ [BYTE_
TEMP]
Temperature 1~4 [xx]
Input temperature setting. The values range from 0~255.
Fan PWM 1~4 [xx]
Input amount of Fan PWM 4 for Smart Fan IV Mode. The values
range from 0~255.
Tolerance of Temperature [xx]
Input tolerance of target temperature. The values range from 0~7.
Critical Temperature [xx]
Determines the time that Fan Out takes to decrease its value by
one step. The values range from 0~255.
Critical Temp Tolerance [xx]
Input tolerance of critical temperature. The values range from 0~7.
The following item appears only when you set Fan Control Mode to [Manual
Mode].
Chapter 3: BIOS setup
3-5
PWM/DC Voltage Output [255]
Sets the voltage allocated for Fan Control. Input value range:
[0~255]
The following item appears only when you set Fan Control Mode to [Thermal
Cruise Mode].
Temperature source [PECI Agent 0]
Allows you to select the temperature source. Configuration
options: [SYSTIN] [CPUTIN] [AUXTIN0] [AUXTIN1] ~ [BYTE_
TEMP]
Chassis 1 Smart Fan Control [Enabled]
Allows you to enable or disable Chassis 1 Smart Fan Control. Configuration options:
[Enabled] [Disabled]
The following sub-items appear only when you set Chassis 1 Smart Fan Control
to [Enabled].
Temperature source [PWM Mode]
Allows you to select the temperature source. Configuration options: [PWM
Mode] [DC Mode]
Fan Control Mode [SMART FAN IV Mode]
Select fan control mode. Configuration options: [Manual Mode] [Thermal
Cruise Mode] [SMART FAN IV Mode]
The following 6 items appear only when you set Fan Control Mode to [Smart
FAN IV Mode].
Temperature source [SYSTIN]
Allows you to select the temperature source. Configuration
options: [SYSTIN] [CPUTIN] [AUXTIN0] [AUXTIN1] ~ [BYTE_
TEMP]
Temperature 1~4 [xx]
Input temperature setting. The values range from 0~255.
Fan PWM 1~4 [xx]
Input amount of Fan PWM 4 for Smart Fan IV Mode. The values
range from 0~255.
Tolerance of Temperature [xx]
Input tolerance of target temperature. The values range from 0~7.
Critical Temperature [xx]
Determines the time that Fan Out takes to decrease its value by
one step. The values range from 0~255.
3-6
EMB-H110B
Critical Temp Tolerance [xx]
Input tolerance of critical temperature. The values range from 0~7.
The following item appears only when you set Fan Control Mode to [Manual
Mode].
PWM/DC Voltage Output [255]
Sets the voltage allocated for Fan Control. Input value range:
[0~255]
The following item appears only when you set Fan Control Mode to [Thermal
Cruise Mode].
Temperature source [SYSTIN]
Allows you to select the temperature source. Configuration
options: [SYSTIN] [CPUTIN] [AUXTIN0] [AUXTIN1] ~ [BYTE_
TEMP]
3.3.7
Power Management
Power Mode [ATX Type]
Select power supply mode. Configuration options: [ATX Type] [AT Type]
The following items appear when you set Power Mode to [ATX Type].
Power Saving (ERP) Control [Disabled]
This item configures power mode for power saving function.
Configuration options: [Disabled] [Enabled]
Restore AC Power Loss [Last State]
[Last State]The system goes into either off or on state, whatever the system
state was.
[Always On]
The system goes into on state after an AC power loss.
[Always Off]
The system goes into off state after an AC power loss.
RTC Wake system from S5 [Disabled]
[Disabled]
Disables system wake up from S5.
[Fixed Time]The system will wake up at the specified hr::min::sec.
Configuration options: [Disabled] [Enabled] .
[Dynamic Time]The system will wake up at the current time plus a specified
number of minutes.
The following items appear when Fixed Time is enabled.
Chapter 3: BIOS setup
3-7
Wake up day/hour/minute/second [0]
Specify the values for day/hour/minute/second.
The following item appears when Wake System with Dynamic Time is enabled.
Wake up minute increase [1]
Specify the number of minutes added to the current time before waking up
system. Input value range: [1~5]
Resume from PME# [Enabled]
Allows you to enable or disable resume from PME# function. Configuration options:
[Enabled] [Disabled]
Resume from PCIE/RI [Enabled]
Allows you to enable or disable resume from PCIE/RI function. Configuration
options: [Enabled] [Disabled]
3.3.7
Digital IO Port Configuration
The items listed in this screen configure Digital IO settings.
DI0 Port1~DI0 Port4 [Output]
Configuration options: [Input] [Output]
The following item appears only when you set DI0 Port1/2/3/4 to [Output].
Output Level [High]
Configuration options: [High] [Low]
DI0 Port5~DI0 Port8 [Input]
Configuration options: [Input] [Output]
3-8
EMB-H110B
3.4
Chipset menu
The Chipset menu items allow you to change the settings for the chipset.
3.4.1
System Agent (SA) Configuration
Max TOLUD [Dynamic]
Allows you to select more useable memory on x86 OS. Select [Dynamic] to adjust
TOLUD automatically based on the largest MMIO length of the installed graphic
controller. Configuration options: [Dynamic] [1 GB] [1.25 GB] [1.5 GB] [1.75GB] [2
GB] [2.25 GB] [2.5GB] [2.75GB] [3 GB] [3.25 GB]
Max Link Speed [Auto]
Allows you to configure the PEG port Gen speed. Configuration options: [Auto]
[Gen1] [Gen2] [Gen3]
Graphics Configuration
Primary Display [Auto]
Allows you to decide which graphics controller to use as the primary boot
device. Configuration options: [Auto] [IGFX] [PEG] [PCIE]
Primary IGFX Boot Display [VBIOS Default]
Select the video device which will be activated during POST. This setting
has no effect if an external graphics device is present. The secondary boot
display selection appears based on your selection and the VGA mode is
supported only on primary display. Configuration options: [VBIOS Default]
[DP] [eDP] [LVDS] [HDMI]
LVDS [Enabled]
Allows you to enable or disable LVDS (CH7511). Configuration options:
[Disabled] [Enabled]
LVDS Panel Type [1024x768 18bit, 60Hz]
Allows you to configure LVDs panel used by Internal Graphics Device.
Configuration options: [640x480, 18bit, 60Hz] [800x480, 18bit, 60Hz]
[800x600, 18bit, 60Hz] [1024x600, 18bit, 60Hz] [1024x768, 18bit, 60Hz]
[1024x768, 24bit, 60Hz] [1280x768, 24bit, 60Hz] [1280x1024, 48bit, 60Hz]
[1366x768, 24bit, 60Hz] [1440x900, 48bit, 60Hz] [1600x1200, 48bit, 60Hz]
[1920x1080, 48bit, 60Hz] [1920x1200, 48bit, 60Hz] [1280x800, 24bit, 60Hz]
[12800x800, 18bit, 60Hz]
Chapter 3: BIOS setup
3-9
3.4.2
PCH-IO Configuration
HD Audio [Auto]
This item controls the detection of HD Audio devices. Configuration options:
[Disabled] [Enabled] [Auto]
3.5
Security menu
The Security menu items allow you to change the system security settings.
3.5.1
Administrator Password
If you have set an administrator password, we recommend that you enter the
administrator password for accessing the system. Otherwise, you might be able to
see or change only selected fields in the BIOS setup program.
To set an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3. Confirm the password when prompted.
To change an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then
press <Enter>.
3.
From the Create New Password box, key in a new password, then press
<Enter>.
4. Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an
administrator password, but press <Enter> when prompted to create/confirm the
password. After you clear the password, the Administrator Password item on top of
the screen shows Not Installed.
3.5.2
User Password
If you have set a user password, you must enter the user password for accessing
the system. The User Password item on top of the screen shows the default Not
Installed. After you set a password, this item shows Installed.
To set a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3. Confirm the password when prompted.
To change a user password:
1.
3-10
Select the User Password item and press <Enter>.
EMB-H110B
2.
From the Enter Current Password box, key in the current password, then
press <Enter>.
3.
From the Create New Password box, key in a new password, then press
<Enter>.
4. Confirm the password when prompted.
To clear the user password, follow the same steps as in changing a user assword,
but press <Enter> when prompted to create/confirm the password. After you clear
the password, the User Password item on top of the screen shows Not Installed.
3.6
Boot menu
The Boot menu items allow you to change the system boot options.
Boot Configuration
Quiet Boot [Enabled]
This item enables/disables Quiet Boot. Configuration options: [Disabled] [Enabled]
Launch PXE ROM [Disabled]
This item enables/disables the execution of UEFI and Legacy PXE OpROM.
Configuration options: [Disabled] [Enabled]
Boot Option Priorities
These items specify the boot device priority sequence from the available devices.
The number of device items that appears on the screen depends on the number of
devices installed in the system.
•
To select the boot device during system startup, press <F7> during POST.
•
To access Windows OS in Safe Mode, do any of the following:
-
Press <F5> during POST.
-
Press <F8> after POST.
Boot Override
These items displays the available devices. The number of device items that
appears on the screen depends on the number of devices installed in the system.
Click an item to start booting from the selected device.
Chapter 3: BIOS setup
3-11
3.7
Save & Exit menu
Save Changes and Reset
Once you are finished making your selections, choose this option from the Save
& Exit menu to ensure the values you selected are saved. When you select this
option, a confirmation window appears. Select Yes to save changes and reset.
Discard Changes and Reset
This option allows you to exit the Setup program without saving your changes.
When you select this option or if you press <Esc>, a confirmation window appears.
Select Yes to discard changes and exit.
Save Options
Save or discard changes to current configuration.
Restore Defaults
Save or restore User Defaults to all setup options.
Save as User Defaults
This item saves current configuration as User Default.
Restore User Defaults
This option restores User Defaults to all setup options.
3-12
EMB-H110B
Appendix
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference.
•
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations. Changes
or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
EMB-H110B
A-1
電子信息產品污染控制標示:圖中之數字為產品之環保使用期限。僅指電子
信息產品中含有的有毒有害物質或元素不致發生外洩或突變從而對環境造成
污染或對人身、財產造成嚴重損害的期限。
有毒有害物質或元素的名稱及含量說明標示:
有害物質或元素
部件名稱
鉛 (Pb)
汞 (Hg)
鎘 (Cd)
六 價
(Cr(VI))
印刷電路板及其
電子組件
×
○
○
外部信號連接頭
及線材
×
○
○
鉻
多 溴 聯 苯
(PBB)
多溴二苯醚
(PBDE)
○
○
○
○
○
○
○:表示該有毒有害物質在該部件所有均質材料中的含量均在 SJ/T 113632006 標准規定的限量要求以下。
×:表示該有毒有害物質至少在該部件的某一均質材料中的含量超出 SJ/T
11363-2006 標准規定的限量要求,然該部件仍符合歐盟指令 2002/95/
EC 的規范。
備註:此產品所標示之環保使用期限,係指在一般正常使用狀況下。
A-2
EMB-H110B
Download PDF
Similar pages