8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain

8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
TECHNICAL DATA SHEET
PE15A5005
PE15A5005 is a broadband high IP3 8 W GaAs PHEMT MMIC-based coaxial power amplifier module designed to be used
in a wide range of commercial and defense applications in the 1.5 to 3.5 GHz frequency range. The amplifier offers 19.5 dB
small signal gain with the typical gain flatness of ±1.25 dB, along with high IP3 performance of 45 dBm. This performance
is achieved through the use of advanced GaAs PHEMT MMIC circuitry. The amplifier operates over the temperature range
of -40°C to 85°C, and characterized by a light weight (45 g) and small size (1.5”x1.2”x0.56”). To facilitate an effective heat
dissipation structure, the amplifier module has 4 screw slots for mounting to a heat sink.
Features
•
•
•
•
•
1.5 GHz to 3.5 GHz Frequency Range
P1dB Output Power: 38.5 dBm
Psat: 39 dBm
Small Signal Gain: 19.5 dB
Gain Flatness: ±1.25 dB
•
•
•
•
Power Added Efficiency @Psat: 32%
50 Ohm Input and Output Matched
-40 to +85°C Operating Temperature
Small Size & Light Weight
Applications
•
•
•
•
•
Telecom Infrastructure
Fixed Microwave Backhaul
Wireless Internent Access
Wireless Local Loop
GPS Applications
•
•
•
•
•
WLAN Repeaters
Microwave Radio Systems
Military & Space
Radar & Sensors
Commercial 2-Way Radio
• Driver Amplifier
• High Power Output Amplifier
• General Purpose Amplification
Electrical Specifications (TA = +25°CVds1,2 = 14V, Idsq1 = 0.25A, Idsq2 = 1.05A, Vgs1,2= -0.97V)
Description
Frequency Range
MinimumTypical Maximum Units
3.5
GHz
dB
Gain Flatness ±1.25
dB
Psat
+39
dBm
Efficiency Psat
32
Output Power at 1 dB Compression Point
+38.5
dBm
Output 3rd Order Intercept Point
+45
dBm
Noise Figure
10
dB
Input Return Loss
15
dB
Output Return Loss
8
dB
Small Signal Gain
Operating Temperature Range
1.5
-40
Thermal Resistance
19.5
+85
6
%
°C
°C/W
. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: 8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF,
SMA PE15A5005
PE15A5005 REV 1.0
1
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
TECHNICAL DATA SHEET
PE15A5005
Absolute Maximum Rating
Parameter
Rating
Units
+16
Volts
Gate Source Voltage
-5
Volts
Drain Source Current
0.38
A
Gate Source Current
1.5
A
Drain Source Voltage
Continuous Dissipation at 25°C
32
W
Channel Temperature
175
°C
-40 to +85
°C
-55° to +135
°C
Operating Temperature (base-plate)
Storage Temperature
ESD Sensitive Material,
Transport material in
Approved ESD bags.
Handle only in approved
ESD Workstation.
.
Mechanical Specifications
Size
.
Weight
Input Connector
Output Connector
0.09 lbs [40.82 g]
SMA Female
SMA Female
Environmental Specifications
Temperature
Operating Range
Storage Range
-40 to +85 deg C
-55 to +135 deg C
..
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: 8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF,
SMA PE15A5005
PE15A5005 REV 1.0
2
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
TECHNICAL DATA SHEET
PE15A5005
Compliance Certifications (visit www.Pasternack.com for current document)
RoHS Compliant
REACH Compliant
12/17/2014
Plotted and Other Data
Notes:
• Values at +25 °C, sea level
• ESD Sensitive Material, Transport material in Approved ESD bags. Handle only in approved ESD Workstation.
• Heat Sink Required for Proper Operation, Unit is cooled by conduction to heat sink. The amplifier module has 4 screw
slots for mounting to a heat sink.
• DO NOT apply Vds without proper negative voltage on Vgs pins.
• GaAs PHEMT MMIC-Based Power up sequence
1.Connect common ports
a. Connect single GND lead
b. Connect all –Vg ports together
c. Connect all +Vd ports together
2.Connect the load, attenuator to protect the VNA.
3.Connect the input port, may have an attenuator at the input (perform the CAL with the loads before connecting the
amplifier to the VNA).
4.Apply the –Vg voltage at close to –Vg Pinch off (Start at -1.9Volts, except for PE15A4014 and PE15A4015 use
-3.0).
5.Apply the +Vd voltage.
6.Adjust the –Vg to the ideal negative voltage (approximately -1.1Volts to -0.97Volts, except for PE15A4014 and
PE15A4015 use -2.6 to -2.4 see datasheet), observe the gain and power output.
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: 8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF,
SMA PE15A5005
PE15A5005 REV 1.0
3
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
TECHNICAL DATA SHEET
PE15A5005
Typical Performance Data
40
30
Gain
Gain & Return Losses (dB)
20
10
0
Output RL
-10
-20
-30
-40
Input RL
1
1.5
2
2.5
3
3.5
4
4.5
Frequency (GHz)
* Data shown is for Vdd1,2=+14V, Iddq1=0.25A, Iddq2=1.05A, Vgs1,2=-0.97V.
25
Noise Figure (dB)
20
15
NF
10
5
0
1
1.5
2
2.5
3
3.5
4
4.5
Frequency (GHz)
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: 8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF,
SMA PE15A5005
PE15A5005 REV 1.0
4
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
TECHNICAL DATA SHEET
PE15A5005
40
35
30
30
20
P1dB
25
10
Gain
EFF
P3dB (dBm)
20
1
1.5
2
2.5
3
3.5
4
Frequency (GHz)
4.5
0
45
50
40
40
35
30
30
20
P3dB
25
10
Gain
1
1.5
2
2.5
3
3.5
Frequency (GHz)
4
4.5
2*F
-20
3*F
-30
-40
-50
-60
-70
-80
-90
-100
1
1.5
2
2.5
3
Frequency (GHz)
3.5
4
4.5
50
45
EFF
20
-10
0
IP3 & IP5 (dBm)
P1dB (dBm)
40
0
Gain (dB) Efficiency (%)
2nd &3rd Harmonics at P3dB (dBc)
50
Gain (dB) Efficiency (%)
45
40
35
IP3
IP5
30
25
1
1.5
2
2.5
3
Frequency (GHz)
3.5
4
* Data shown is for Vdd1,2=+14V, Iddq1=0.25A,
Iddq2=1.05A, Vgs1,2=-0.97V.
2nd &3rd Harmonics at P1dB (dBc)
0
-10
2*F
-20
3*F
-30
-40
-50
-60
-70
-80
-90
-100
1
1.5
2
2.5
3
Frequency (GHz)
3.5
4
4.5
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: 8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF,
SMA PE15A5005
PE15A5005 REV 1.0
5
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
TECHNICAL DATA SHEET
PE15A5005
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA from Pasternack Enterprises
has same day shipment for domestic and International orders. Our RF, microwave and millimeter wave products maintain a
99% availability and are part of the broadest selection in the industry.
Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price,
inventory and certifications: 8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier, 19.5 dB Gain, 45 dBm IP3, 10 dB NF,
SMA PE15A5005
URL: http://www.pasternack.com/3.5-ghz-high-power-amplifier-19.5-db-gain-45-dbm-ip3-10-db-sma-pe15a5005-p.aspx
PE15A5005 REV 1.0
6
PE15A5005 CAD Drawing
8 Watt Psat, 1.5 GHz to 3.5 GHz, High Power Amplifier,
19.5 dB Gain, 45 dBm IP3, 10 dB NF, SMA
PE15A5005 REV 1.0
7
Download PDF
Similar pages