IR High-definition Network Speed Dome User Manual

IR High-definition Network
Speed Dome
User Manual
UD.6L0201D1111A01
User Manual of Network Speed Dome
1
Thank you for purchasing our product. If there are any questions, or requests, please
do not hesitate to contact the dealer.
This manual applies to Network Speed Dome.
This manual may contain several technical or printing errors, and the content is
subject to change without notice. The updates will be added to the new version of
this manual. We will readily improve or update the products or procedures described
in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability
of the security or signaling aspects of this product. UL has only tested for fire, shock
or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the security or signaling
aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF
ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
0500041030710
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
3
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards to Cautions Follow these precautions to
prevent serious injury or death.
prevent potential injury or material
damage.
Warnings:
 Please adopt the power adapter which can meet the safety extra low voltage
(SELV) standard. And source with 24VAC10% or 12VDC10% (depending on
models) according to the IEC60950-1 and Limited Power Source standard. The
power consumption cannot be less than the required value.
 Do not connect several devices to one power adapter as an adapter overload may
cause over-heating and can be a fire hazard.
 When the product is installed on a wall or ceiling, the device should be firmly
fixed.
 To reduce the risk of fire or electrical shock, do not expose the indoor used
product to rain or moisture.
 This installation should be made by a qualified service person and should
conform to all the local codes.
 Please install blackouts equipment into the power supply circuit for convenient
supply interruption.
 If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the product yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
4
Cautions:
 Make sure the power supply voltage is correct before using the product.
 Do not drop the product or subject it to physical shock. Do not install the product
on vibratory surface or places.
 Do not expose it to high electromagnetic radiating environment.
 Do not aim the lens at the strong light such as sun or incandescent lamp. The
strong light can cause fatal damage to the product.
 The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor not be exposed to the laser
beam.
 Do not place the product in extremely hot, cold temperatures (the operating
temperature should be between -30°C ~ 65°C), dusty or damp environment.
 To avoid heat accumulation, good ventilation is required for a proper operating
environment.
 While shipping, the product should be packed in its original packing.
 Please use the provided glove when open up the product cover. Do not touch the
product cover with fingers directly, because the acidic sweat of the fingers may
erode the surface coating of the product cover.
 Please use a soft and dry cloth when clean inside and outside surfaces of the
product cover. Do not use alkaline detergents.
 Improper use or replacement of the battery may result in hazard of explosion.
Please use the manufacturer recommended battery type.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
5
Table of Contents
Chapter 1
Overview.................................................................................................................... 8
1.1
System Requirement........................................................................................................... 8
1.2
Appearance ........................................................................................................................ 8
1.3
Functions............................................................................................................................ 8
Chapter 2
2.1
Network Connection ................................................................................................ 11
Setting the Network Speed Dome over the LAN ................................................................ 11
2.1.1
Wiring over the LAN ..................................................................................................... 11
2.1.2
Detecting and Changing the IP Address ......................................................................... 12
2.2
Setting the Network Speed Dome over the WAN ............................................................... 13
2.2.1
Static IP Connection ...................................................................................................... 13
2.2.2
Dynamic IP Connection ................................................................................................. 14
Chapter 3
Access to the Network Speed Dome ......................................................................... 17
3.1
Accessing by Web Browsers .............................................................................................. 17
3.2
Accessing by Client Software ............................................................................................. 19
Chapter 4
Live View ................................................................................................................. 21
4.1
Power-up Action ............................................................................................................... 21
4.2
Live View Page.................................................................................................................. 21
4.3
Starting Live View ............................................................................................................. 22
4.4
Recording and Capturing Pictures Manually ...................................................................... 24
4.5
Operating PTZ Control....................................................................................................... 24
4.5.1
PTZ Control Panel ......................................................................................................... 25
4.5.2
Setting / Calling a Preset ............................................................................................... 25
4.5.3
Setting / Calling a Patrol ................................................................................................ 27
4.5.4
Setting / Calling a Pattern.............................................................................................. 29
4.6
Chapter 5
Configuring Live View Parameters ..................................................................................... 30
PTZ Configuration..................................................................................................... 31
5.1
Configuring Initial Position ................................................................................................ 31
5.2
Configuring Basic PTZ Parameters ..................................................................................... 32
5.3
Configuring PTZ Limit Stops............................................................................................... 33
5.4
Configuring Scheduled Tasks ............................................................................................. 34
5.5
Configuring Park Actions ................................................................................................... 36
5.6
Configuring Privacy Mask .................................................................................................. 37
5.7
Configuring Smart Tracking ............................................................................................... 38
5.8
Clearing PTZ Configurations .............................................................................................. 39
Chapter 6
Speed Dome Configuration ...................................................................................... 40
6.1
Configuring Local Parameters ............................................................................................ 40
6.2
Configuring Time Settings ................................................................................................. 41
6.3
Configuring Network Settings............................................................................................ 44
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
6
6.3.1
Configuring TCP/IP Settings ........................................................................................... 44
6.3.2
Configuring Port Settings .............................................................................................. 45
6.3.3
Configuring PPPoE Settings ........................................................................................... 46
6.3.4
Configuring DDNS Settings ............................................................................................ 46
6.3.5
Configuring SNMP Settings ........................................................................................... 49
6.3.6
Configuring 802.1X Settings .......................................................................................... 50
6.3.7
Configuring QoS Settings............................................................................................... 51
6.3.8
Configuring FTP Settings ............................................................................................... 52
6.3.9
Configuring NAT Settings............................................................................................... 53
6.3.10
6.4
Configuring Email Settings ........................................................................................ 54
Configuring Video and Audio Settings ............................................................................... 56
6.4.1
Configuring Video Settings ............................................................................................ 56
6.4.2
Configuring Audio Settings ............................................................................................ 57
6.4.3
Configuring ROI Settings ............................................................................................... 58
6.5
Configuring Image Settings ............................................................................................... 59
6.5.1
Configuring Display Settings .......................................................................................... 59
6.5.2
Configuring OSD Settings .............................................................................................. 66
6.5.3
Configuring Text Overlay Settings .................................................................................. 68
6.6
Configuring and Handling Alarms ...................................................................................... 68
6.6.1
Configuring Motion Detection ....................................................................................... 69
6.6.2
Configuring Video Loss Alarm ....................................................................................... 72
6.6.3
Configuring Tamper-proof Alarm ................................................................................... 73
6.6.4
Configuring External Alarm Input .................................................................................. 74
6.6.5
Configuring Alarm Output ............................................................................................. 76
6.6.6
Handling Exception ....................................................................................................... 77
Chapter 7
Record Settings ........................................................................................................ 79
7.1
Configuring NAS Settings................................................................................................... 79
7.2
Configuring Recording Schedule ........................................................................................ 80
7.3
Configuring Snapshot Settings........................................................................................... 84
Chapter 8
Playback................................................................................................................... 86
Chapter 9
Log Searching ........................................................................................................... 90
Chapter 10
Others ...................................................................................................................... 92
10.1
Managing User Accounts .................................................................................................. 92
10.2
Configuring RTSP Authentication....................................................................................... 95
10.3
Configuring Anonymous Visit ............................................................................................ 95
10.4
Configuring IP Address Filter ............................................................................................. 96
10.5
Viewing Device Information .............................................................................................. 96
10.6
Maintenance .................................................................................................................... 97
10.6.1
Rebooting the Speed Dome ...................................................................................... 97
10.6.2
Restoring Default Settings ......................................................................................... 97
10.6.3
Importing/Exporting Configuration File ..................................................................... 98
10.6.4
Upgrading the System ............................................................................................... 98
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
10.7
7
RS-485 Settings ............................................................................................................... 100
Appendix ....................................................................................................................................... 101
Appendix 1 SADP Software Introduction ..................................................................................... 101
Appendix 2 Port Mapping ........................................................................................................... 103
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
8
User Manual of Network Speed Dome
Chapter 1 Overview
1.1 System Requirement
System requirement of web browser accessing is as follows:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above
version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above
versions.
1.2 Appearance
Figure 1-1 Appearance
1.3 Functions
Note: The functions vary depending on the models of speed dome.
 Limit Stops
The dome can be programmed to move within the limit stops (left/right, up/down).
 Scan Modes
The dome provides 5 scan modes: auto scan, tilt scan, frame scan, random scan and
panorama scan.
 Preset Freezing
This feature freezes the scene on the monitor when the dome is moving to a preset.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
9
This allows for smooth transition from one preset scene to another. It also
guarantees that masked area will not be revealed when the dome is moving to a
preset.
 Presets
A preset is a predefined image position. When the preset is called, the dome will
automatically move to the defined position. The presets can be added, modified,
deleted and called.
 Label Display
The on-screen label of the preset title, azimuth/elevation, zoom, time and dome
name can be displayed on the monitor. The displays of time and speed dome name
can be programmed.
 Auto Flips
In manual tracking mode, when a target object goes directly beneath the dome, the
video will automatically flips 180 degrees in horizontal direction to maintain
continuity of tracking. This function can also be realized by auto mirror image
depending on different camera models.
 Privacy Mask
This function allows you to block or mask certain area of a scene, for preventing the
personal privacy from recording or live viewing. A masked area will move with pan
and tilt functions and automatically adjust in size as the lens zooms telephoto and
wide.
 3D Positioning
In the client software, use the left key of mouse to click on the desired position in the
video image and drag a rectangle area in the lower right direction, then the dome
system will move the position to the center and allow the rectangle area to zoom in.
Use the left key of mouse to drag a rectangle area in the upper left direction to move
the position to the center and allow the rectangle area to zoom out.
 Proportional Pan/Tilt
Proportional pan/tilt automatically reduces or increases the pan and tilt speeds
according to the amount of zoom. At telephoto zoom settings, the pan and tilt
speeds will be slower than at wide zoom settings. This keeps the image from moving
too fast on the live view image when there is a large amount of zoom.
 Auto Focus
The auto focus enables the camera to focus automatically to maintain clear video
images.
 Day/Night Auto Switch
The speed domes deliver color images during the day. And as light diminishes at night,
the speed domes switch to night mode and deliver black and white images with high
quality.
 Slow Shutter
In slow shutter mode, the shutter speed will automatically slow down in low
illumination conditions to maintain clear video images by extending the exposure
time. The feature can be enabled or disabled.
 Backlight Compensation (BLC)
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
10
If you focus on an object against strong backlight, the object will be too dark to be
seen clearly. The BLC (Backlight Compensation) function can compensate light to the
object in the front to make it clear, but this causes the over-exposure of the
background where the light is strong.
 Wide Dynamic Range (WDR)
The wide dynamic range (WDR) function helps the camera provide clear images even
under back light circumstances. When there are both very bright and very dark areas
simultaneously in the field of view, WDR balances the brightness level of the whole
image and provide clear images with details.
Note: This feature varies depending on speed dome models.
 White Balance (WB)
White balance can remove the unrealistic color casts. White balance is the white
rendition function of the camera to adjust the color temperature according to the
environment automatically.
 Patrol
A patrol is a memorized series of pre-defined preset function. The scanning speed
between two presets and the dwell time at the preset are programmable.
 Pattern
A pattern is a memorized series of pan, tilt, zoom, and preset functions. By default
the focus and iris are in auto status during the pattern is being memorized.
 Power Off Memory
The dome supports the power off memory capability with the predefined resume
time. It allows the dome to resume its previous position after power is restored.
 Scheduled Task
A time task is a preconfigured action that can be performed automatically at a
specific date and time. The programmable actions include: auto scan, random scan,
patrol 1-8 ,pattern 1-4, preset 1-8,frame scan, panorama scan, tilt scan, day, night,
reboot, PT adjust, Aux Output, etc.
 Park Action
This feature allows the dome to start a predefined action automatically after a period
of inactivity.
 User Management
The dome allows you to edit users with different levels of permission, in the admin
login status. Multiple users are allowed to access and control the same network
speed dome via network simultaneously.
 3D Digital Noise Reduction
Comparing with the general 2D digital noise reduction, the 3D digital noise reduction
function processes the noise between two frames besides processing the noise in
one frame. The noise will be much less and the video will be clearer.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
11
User Manual of Network Speed Dome
Chapter 2 Network Connection
Before you start:
 If you want to set the network speed dome via a LAN (Local Area Network),
please refer to Section 2.1 Setting the Network Speed Dome over the LAN.
 If you want to set the network speed dome via a WAN (Wide Area Network),
please refer to Section 2.2 Setting the Network Speed Dome over the WAN.
2.1 Setting the Network Speed Dome over the LAN
Purpose:
To view and configure the speed dome via a LAN, you need to connect the network
speed dome in the same subnet with your computer, and install the SADP or client
software to search and change the IP of the network speed dome.
Note: For the detailed introduction of SADP, please refer to Appendix 1.
2.1.1 Wiring over the LAN
The following figures show the two ways of cable connection of a network speed
dome and a computer:
Purpose:
 To test the network speed dome, you can directly connect the network speed
dome to the computer with a network cable as shown in Figure 2-1.
 Refer to the Figure 2-2 to set the network speed dome over the LAN via a switch
or a router.
Network Cable
Figure 2-1 Connecting Directly
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
12
User Manual of Network Speed Dome
Network
Cable
Speed Dome
Switch or Router
PC
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Detecting and Changing the IP Address
You need the IP address to visit the network speed dome.
Steps:
1.
To get the IP address, you can choose either of the following methods:
 Use SADP, a software tool which can automatically detect the online
network speed domes in the LAN and list the device information including IP
address, subnet mask, port number, device serial number, device version,
etc., shown in Figure 2-3.
 Use the client software to list the online devices. Please refer to the user
manual of client software for detailed information.
2.
Change the IP address and subnet mask to the same subnet as that of your
computer.
3.
Enter the IP address of network speed dome in the address field of the web
browser to view the live video.
Notes:
 The default IP address is 192.0.0.64. The default user name is admin, and
password is 12345.
 For accessing the network speed dome from different subnets, please set the
gateway for the network speed dome after you logged in. For detailed
information, please refer to Section 6.3.1 Configuring TCP/IP Settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
13
User Manual of Network Speed Dome
Figure 2-3 SADP Interface
2.2 Setting the Network Speed Dome over the WAN
Purpose:
This section explains how to connect the network speed dome to the WAN with a
static IP or a dynamic IP.
2.2.1 Static IP Connection
Before you start:
Please apply a static IP from an ISP (Internet Service Provider). With the static IP
address, you can connect the network speed dome via a router or connect it to the
WAN directly.
 Connecting the network speed dome via a router
Steps:
1. Connect the network speed dome to the router.
2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2
Detecting and Changing the IP Address for detailed IP address configuration of
the speed dome.
3. Save the static IP in the router.
4. Set port mapping, E.g., 80, 8000 and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Note: Refer to Appendix 2 for detailed information about port mapping.
5. Visit the network speed dome through a web browser or the client software over
the internet.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
14
Figure 2-4 Accessing the Speed Dome through Router with Static IP
Connecting the network speed dome with static IP directly
You can also save the static IP in the speed dome and directly connect it to the
internet without using a router. Refer to Section 2.1.2 Detecting and Changing the IP
Address for detailed IP address configuration of the speed dome.

Figure 2-5 Accessing the Speed Dome with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect
the network speed dome to a modem or a router.

Connecting the network speed dome via a router
Steps:
1. Connect the network speed dome to the router.
2. In the speed dome, assign a LAN IP address, the subnet mask and the gateway.
Refer to Section 2.1.2 Detecting and Changing the IP Address for detailed LAN
configuration.
3. In the router, set the PPPoE user name, password and confirm the password.
4. Set port mapping. E.g. 80, 8000 and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Note: Refer to Appendix 2 for detailed information about port mapping.
5. Apply a domain name from a domain name provider.
6. Configure the DDNS settings in the setting interface of the router.
7. Visit the speed dome via the applied domain name.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome

15
Connecting the network speed dome via a modem
Purpose:
This speed dome supports the PPPoE auto dial-up function. The speed dome gets a
public IP address by ADSL dial-up after the speed dome is connected to a modem.
You need to configure the PPPoE parameters of the network speed dome. Refer to
Section 6.3.3 Configuring PPPoE Settings for detailed configuration.
Figure 2-6 Accessing the Speed Dome with Dynamic IP
Note: The obtained IP address is dynamically assigned via PPPoE, so the IP address
always changes after rebooting the speed dome. To solve the inconvenience of the
dynamic IP, you need to get a domain name from the DDNS provider (E.g.
DynDns.com). Please follow below steps for normal domain name resolution and
private domain name resolution to solve the problem.

Normal Domain Name Resolution
Figure 2-7 Normal Domain Name Resolution
Steps:
1. Apply a domain name from a domain name provider.
2. Configure the DDNS settings in the DDNS Settings interface of the network speed
dome. Refer to Section 6.3.4 Configuring DDNS Settings for detailed
configuration.
3. Visit the speed dome via the applied domain name.

Private Domain Name Resolution
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
16
Figure 2-8 Private Domain Name Resolution
Steps:
1. Install and run the IP Server software in a computer with a static IP.
2. Access the network speed dome through the LAN with a web browser or the
client software.
3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4
Configuring DDNS Settings for detailed configuration.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
17
User Manual of Network Speed Dome
Chapter 3 Access to the Network
Speed Dome
3.1 Accessing by Web Browsers
Steps:
1. Open the web browser.
2. In the address field, input the IP address of the network speed dome, e.g.,
192.0.0.64 and press the Enter key to enter the login interface.
3. Select English as the interface language on the top-right of login interface.
4.
Input the user name and password and click
.
Note: The default user name is admin, password is 12345.
Figure 3-1 Login Interface
5. Install the plug-in before viewing the live video and operating the speed dome.
Please follow the installation prompts to install the plug-in.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
Figure 3-2 Download and Install Plug-in
Figure 3-3 Install Plug-in (1)
Figure 3-4 Install Plug-in (2)
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
18
User Manual of Network Speed Dome
19
Figure 3-5 Install Plug-in (3)
Note: You may have to close the web browser to install the plug-in. Please reopen
the web browser and log in again after installing the plug-in.
3.2 Accessing by Client Software
The product CD contains the client software. You can view the live video and manage
the speed dome with the client software.
Follow the installation prompts to install the client software and WinPcap. The
configuration interface and live view interface of client software are shown bellow.
Figure 3-6 iVMS-4200 PCNVR Control Panel
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
20
Figure 3-7 iVMS-4200 PCNVR Live View Interface
Notes:
 If you use third party VMS software, please contact technical support of our
branch for camera firmware.
 For detailed information about client software of our company, please refer to
the user manual of the software. This manual mainly introduces accessing to the
network speed dome by web browser.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
21
User Manual of Network Speed Dome
Chapter 4 Live View
4.1 Power-up Action
After the power is applied, the speed dome will perform self-test actions. It begins
with lens actions and then pan and tilt movement. After the power-up self-test
actions, the information as shown in Figure 4-1 will be displayed on screen for 40
seconds.
The System Information displayed on the screen includes the dome model, address,
protocol, version and other information. The COMMUNICATION refers to the baud
rate, parity, data bit and stop bit of the dome. e.g., 2400, N, 8, 1 indicates the dome
is configured with the baud rate of 2400, no parity, 8 data bits and 1 stop bit.
Model
XX-2XXXXX-X
ADDRESS
COMMUNICATION
SOFTWARE VERSION
CAMERA VERSION
LANGUAGE
0
0000,0,0,0
V000
V000
ENGLISH
Figure 4-1 Power-up information
4.2 Live View Page
Purpose:
The live video page allows you to view live video, capture images, realize PTZ control,
set/call presets and configure video parameters.
Log in the network speed dome to enter the live view page, or you can click
on the menu bar of the main page to enter the live view page.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
22
User Manual of Network Speed Dome
Descriptions of the live view page:
Menu Bar
Click to show or hide
Live View Parameters
PTZ control panel
PTZ control
Live view window
Preset/patrol/pattern
Toolbar
Figure 4-2 Live View Page
Menu Bar:
Click each tab to enter Live View, Playback, Log and Configuration page respectively.
Live View Window:
Display the live video.
Toolbar:
Operations on the live view page, e.g., live view, capture, record, audio on/off,
two-way audio, etc.
PTZ Control:
Panning, tilting, focusing and zooming actions of the speed dome. The lighter, wiper,
one-touch focus and lens initialization control.
Preset/patrol/pattern:
Set and call the preset/patrol/pattern for the speed dome.
Live View Parameters:
Configure the image size and stream type of the live video.
4.3 Starting Live View
In the live view window as shown in Figure 4-3, click
on the toolbar to start the
live view of the speed dome.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
23
User Manual of Network Speed Dome
Figure 4-3 Start Live View
Table 4-1 Descriptions of the Toolbar
Icon
Description
Icon
Live view on
Description
Live view off
Manually capture the pictures
Manual recording off
Manual recording on
Audio on and adjust volume
Mute
Two-way audio off
Two-way audio on
3D positioning
Manual tracking
Note: Before using the two-way audio or recording with audio functions, please set
the Stream Type to Video & Audio referring to Section 6.4.1 Configuring Video
Settings.
Full-screen Mode:
You can double-click on the live video to switch the current live view into full-screen
or return to normal mode from the full-screen.
3D Positioning:
Steps:
1.
Click
on the tool bar of live view interface.
2.
Operate the 3D positioning function:
 Left click a position of the live video. The corresponding position will be
moved to the center of the live video.
 Hold down the left mouse button and drag the mouse to the lower right on
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
24
User Manual of Network Speed Dome
the live video. The corresponding position will be moved to the center of the live
video and zoomed in.
 Hold down the left mouse button and drag the mouse to the upper left on
the live video. The corresponding position will be moved to the center of the live
video and zoomed out.
Manual Tracking:
Before you start:
Please enter the Smart Tracking settings interface and enable smart tracking first.
Configuration > Advanced Configuration> PTZ > Smart Tracking
Steps:
1.
Click
on the tool bar of live view interface.
2. Left click a moving object in the live video.
The speed dome will track the object automatically.
Note: not all the speed dome models support this function. Please take the browser
interface of the actual product as standard.
Please refer to the following sections for more information:
 Configuring remote recording in Section 7.2 Configuring Recording Schedule.
 Setting the image quality of the live video in Section 6.1 Configuring Local
Parameters and Section 6.4.1 Configuring Video Settings.
 Setting the OSD text on live video in Section 6.5.2 Configuring OSD Settings.
4.4 Recording and Capturing Pictures Manually
In the live view interface, click
click
on the toolbar to capture the live pictures or
to record the live video. The local saving paths of the captured pictures
and clips can be set in the Configuration > Local Configuration interface.
To configure remote automatic recording, please refer to Section 7.2 Configuring
Recording Schedule.
Note: The captured image will be saved as a JPEG file in your computer.
4.5 Operating PTZ Control
Purpose:
In the live view interface, you can use the PTZ control buttons to control panning,
tilting and zooming.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
25
User Manual of Network Speed Dome
4.5.1 PTZ Control Panel
On the live view page, click
to show the PTZ control panel or click
to
hide it.
Click the direction buttons to control the pan/tilt movements.
Click the zoom/iris/focus buttons to realize lens control.
Figure 4-4 PTZ Control Panel
Table 4-2 Descriptions of PTZ Control Panel
Button
Description
Zoom in/out
Focus near/far
Iris +/Adjust speed of pan/tilt movements
4.5.2 Setting / Calling a Preset
Purpose:
A preset is a predefined image position. For the defined preset, you can click the
calling button to quickly view the desired image position.
 Setting a Preset:
Steps:
1. In the PTZ control panel, select a preset number from the preset list.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
26
User Manual of Network Speed Dome
Figure 4-5 Setting a Preset
2. Use the PTZ control buttons to move the lens to the desired position.
• Pan the speed dome to the right or left.
• Tilt the speed dome up or down.
• Zoom in or out.
• Refocus the lens.
3. Click
to finish the setting of the current preset.
4. You can click
to delete the preset.
Note: You can configure up to 256 presets.
 Calling a Preset:
In the PTZ control panel, select a defined preset from the list and click
preset.
to call the
Figure 4-6 Calling a Preset
Note: The following presets are predefined with special commands. You can only call
them but not configure them. For instance, preset 99 is the “Start auto scan”. If you
call the preset 99, the speed dome starts auto scan function.
Table 4-3 Special Presets
Special
Preset
33
34
35
36
37
38
39
40
Function
Auto flip
Back to initial position
Call patrol 1
Call patrol 2
Call patrol 3
Call patrol 4
IR cut filter in
IR cut filter out
Special
Preset
93
94
95
96
97
98
99
100
Function
Set limit stops manually
Remote reboot
Call OSD menu
Stop a scan
Start random scan
Start frame scan
Start auto scan
Start tilt scan
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
27
User Manual of Network Speed Dome
41
42
43
44
92
Call pattern 1
Call pattern 2
Call pattern 3
Call pattern 4
Start to set limit stops
101
102
103
104
105
Start panorama scan
Call patrol 5
Call patrol 6
Call patrol 7
Call patrol 8
Note: You may need to use the OSD(On Screen Display) menu when controlling the
speed dome remotely. To display the OSD menu on the live view screen, you can call
the preset number 95.
4.5.3 Setting / Calling a Patrol
Purpose:
A patrol is a memorized series of preset function. It can be configured and called on
the patrol settings interface. There are up to 8 patrols for customizing. A patrol can
be configured with 32 presets.
Before you start:
Please make sure that the presets you want to add into a patrol have been defined.
 Setting a Patrol:
Steps:
1. In the PTZ control panel, click
2. Select a patrol number from
3. Click
to enter the patrol settings interface.
.
to enter the adding interface of preset as shown in Figure 4-7.
Figure 4-7 Adding Presets
4. Configure the preset number, patrol duration and patrol speed.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
Name
Patrol Duration
Patrol Speed
5. Click
28
Description
It is the duration staying on one patrol point. The speed
dome moves to another patrol point after the patrol
time.
It is the speed of moving from one preset to another.
to save a preset into the patrol.
6. Repeat the steps from 3 to 5 to add more presets.
7. Click
to save all the patrol settings.

Calling a Patrol:
In the PTZ control panel, select a defined patrol from
to call the patrol as shown in Figure 4-8.
Figure 4-8 Calling a Preset

Buttons on the Patrols interface:
Buttons
Description
Save a patrol
Call a patrol
Stop a patrol
Enter the adding interface of preset
Modify a preset
Delete a preset
Delete all the presets in one patrol
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
and click
29
User Manual of Network Speed Dome
4.5.4 Setting / Calling a Pattern
Purpose:
A pattern is a memorized series of pan, tilt, zoom, and preset functions. It can be
called on the pattern settings interface. There are up to 4 patterns for customizing.
 Setting a Pattern:
Steps:
1. In the PTZ control panel, click
to enter the pattern settings interface.
2. Select a pattern number from the list as shown in Figure 4-9.
Figure 4-9 Patterns Settings Interface
3. Click
to enable recording the panning, tilting and zooming actions.
4. Use the PTZ control buttons to move the lens to the desired position after the
information of PROGRAM PATTERN REMAINNING MENORY(%) shown in Figure
4-10 is displayed on the screen.
• Pan the speed dome to the right or left.
• Tilt the speed dome up or down.
• Zoom in or out.
• Refocus the lens.
Figure 4-10 Remaining Memory
5. Click

to save all the pattern settings.
Buttons on the Patterns interface:
Buttons
Description
Start to record a pattern.
Stop recording a pattern.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
30
User Manual of Network Speed Dome
Call the current pattern.
Stop the current pattern.
Delete the current pattern.
Notes:

These 4 patterns can be operated separately and with no priority level.

When configuring and calling the pattern, proportional pan is valid; the limit
stops and auto flip will be invalid; and the 3D positioning operation is not
supported.
4.6 Configuring Live View Parameters

Main stream/Sub-stream/Third stream:
You can select
,
or
as the stream type of
live viewing. The main stream is with a relatively high resolution and needs much
bandwidth. The sub-stream is with a low resolution and needs less bandwidth. The
resolution of third stream is between that of main stream and sub stream. The
default setting of stream type is
.
Note: Please refer to Section 6.4.1 Configuring Video Settings for more detailed
parameter settings of the main stream, sub-stream and third stream respectively.

Image Size:
You can scale up/down the live view image by clicking
image size can be 4:3, 16:9, original or auto.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
. the
User Manual of Network Speed Dome
31
Chapter 5 PTZ Configuration
5.1 Configuring Initial Position
Purpose:
The initial position is the origin of PTZ coordinates. It can be the factory default initial
position. You can also customize the initial position according to your own demand.
 Customize an Initial Position:
Steps:
1. Enter the Initial Position Configuration interface:
Configuration > Advanced Configuration > PTZ > Initial Position
Figure 5-1 PTZ Configuration
2.
Click the PTZ control buttons to find a position as the initial position of the dome;
you can also call a defined preset and set it as the initial position of the dome.
3.
Click Set to save the position.

Call/delete an Initial Position:
You can click
to call the initial position. You can click
delete the initial position and restore the factory default initial position.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
to
User Manual of Network Speed Dome
32
5.2 Configuring Basic PTZ Parameters
Purpose:
You can configure the basic PTZ parameters, including proportional pan, preset
freezing, preset speed, etc.
1. Enter the Basic PTZ Parameter Configuration interface:
Configuration > Advanced Configuration > PTZ > Basic
Figure 5-2 Basic PTZ Configuration Interface
2. Configure the following settings:
 Basic Parameters: Enable/disable proportional pan and preset freezing, set the
preset speed, keyboard control speed, and auto scan speed.
 Proportional Pan: If you enable this function, the pan/tilt speeds change
according to the amount of zoom. When there is a large amount of zoom, the
pan/tilt speed will be slower for keeping the image from moving too fast on
the live view image.
 Preset Freezing: This function enables the live view to switch directly from
one scene defined by a preset to another, without showing the middle areas
between these two, to ensure the surveillance efficiency. It can also reduce
the use of bandwidth in a digital network system.
Note: Preset freezing function is invalid when you calling a pattern.
 Preset Speed: You can set the speed of a defined preset from 1 to 8.
 Keyboard Control Speed: Define the speed of PTZ control by a keyboard as
Low, Normal or High.
 Auto Scan Speed: The dome provides 5 scan modes: auto scan, tilt scan,
frame scan, random scan and panorama scan. The scan speed can be set from
level 1 to 40.
 PTZ OSD: Set the on-screen display duration of the PTZ status.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome

33
 Zoom Status: Set the OSD duration of zooming status as 2 seconds, 5 seconds,
10 seconds, Always Close or Always Open.
 PT Status: Set the azimuth angle display duration while panning and tilting as
2 seconds, 5 seconds, 10 seconds, Always Close or Always Open.
 Preset Status: Set the preset name display duration while calling the preset as
2 seconds, 5 seconds, 10 seconds, Always Close or Always Open.
Power-off Memory: The dome can resume its previous PTZ status or actions after
it restarted from a power-off. You can set the time point of which the dome
resumes its PTZ status. You can set it to resume the status of 30 seconds, 60
seconds, 300 seconds or 600 seconds before power-off.
3. Click
to save the settings.
5.3 Configuring PTZ Limit Stops
Purpose:
The dome can be programmed to move within the configurable limit stops (left/right,
up/down).
Steps:
1. Enter the Limit Configuration interface:
Configuration > Advanced Configuration > PTZ > Limit
Figure 5-3 Configure the PTZ Limit
2.
Click the checkbox of Enable Limit and choose the limit type as manual stops or
scan stops.
 Manual Stops:
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
34
When manual limit stops are set, you can operate the PTZ control panel
manually only in the limited surveillance area.
 Scan Stops:
When scan limit stops are set, the random scan, frame scan, auto scan, tilt scan,
panorama scan is performed only in the limited surveillance area.
Note: Manual Stops of Limit Type is prior to Scan Stops. When you set these two
limit types at the same time, Manual Stops is valid and Scan Stops is invalid.
3. Click the PTZ control buttons to find the left/right/up/down limit stops; you can
also call the defined presets and set them as the limits of the dome.
4. Click Set to save the limits or click Clear to clear the limits.
5.4 Configuring Scheduled Tasks
Purpose:
You can configure the network dome to perform a certain action automatically in a
user-defined time period.
Steps:
1. Enter the Scheduled Task Settings interface:
Configuration> Advanced Configuration> PTZ > Scheduled Tasks
Figure 5-4 Configure Scheduled Tasks
2.
3.
4.
Check the checkbox of Enable Scheduled Task.
Set the Park Time. You can set the park time (a period of inactivity) before the
dome starts the scheduled tasks.
Set the schedule and task details.
Steps:
(1) Click
to edit the task schedule.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
35
User Manual of Network Speed Dome
Figure 5-5 Edit the Schedule and Task Type
(2) Choose the day you want to set the task schedule.
(3) Click All Day to set the schedule as all day; or click Customize and input the
Start Time and End Time for each task, and click Enter on your keyboard to
enter the time.
(4) Choose the task type from the drop-down list. You can choose scan, preset,
pattern and etc.
Figure 5-6 Task Types
(5) After you set the scheduled task, you can copy the task to other days
(Optional).
(6) Click
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
36
User Manual of Network Speed Dome
Note: The time of each task can’t be overlapped. Up to 10 tasks can be
configured for each day.
5.
Click
to save the settings.
5.5 Configuring Park Actions
Purpose:
This feature allows the dome to start a predefined park action (scan, preset, pattern
and etc.) automatically after a period of inactivity (park time).
Note: Scheduled Tasks function is prior to Park Action function. When these two
functions are set at the same time, only the Scheduled Tasks function takes effect.
Steps:
1. Enter the Park Action Settings interface:
Configuration > Advanced Configuration> PTZ > Park Action
Figure 5-7 Set the Park Action
2.
3.
4.
Check the checkbox of Enable Park Action.
Set the Park Time as the inactivity time of the dome before it starts the park
actions.
Choose Action Type the from the drop-down list.
Figure 5-8 Action Types
5.
Click
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
37
User Manual of Network Speed Dome
5.6 Configuring Privacy Mask
Purpose:
Privacy mask enables you to cover certain areas on the live video to prevent certain
spots in the surveillance area from being live viewed and recorded.
Steps:
1. Enter the Privacy Mask Settings interface:
Configuration > Advanced Configuration> PTZ > Privacy Mask
Figure 5-9 Draw the Privacy Mask
2.
Click the PTZ control buttons to find the area you want to set the privacy mask.
3.
Click
; click and drag the mouse in the live video window to draw
the area.
4. You can drag the corners of the red rectangle area to draw a polygon mask.
5.
Click
to finish drawing or click
to clear all of the
areas you set without saving them.
6.
Click
to save the privacy mask, and it will be listed in the Privacy
Mask List area; you can select a mask and click
to delete it from the list;
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
38
you can also define the color of the masks.
Figure 5-10 Privacy Mask List
Figure 5-11 Define Mask Color
7. Check the checkbox of Enable Privacy Mask to enable this function.
Note: You are allowed to draw up to 24 areas on the same image.
5.7 Configuring Smart Tracking
Purpose:
The speed dome tracks the moving objects automatically after you configure this
function.
Steps:
1. Enter the Smart Tracking Settings interface:
Configuration > Advanced Configuration> PTZ > Smart Tracking
Figure 5-12 Configure Smart Tracking
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
39
User Manual of Network Speed Dome
2. Check the
check box to enable smart tracking function.
3. Click the PTZ buttons to select an object.
4. Click
to set the current zoom ratio as the tracking zoom ratio.
5. Set the tracking duration. The speed dome stops tracking when the duration time
is up. The duration ranges from 0 to 300 seconds.
Notes:
 Setting the duration to 0 means that there’s no duration when speed dome
tracks.
 Not all the speed dome models support this function. Please take the browser
interface of the actual product as standard.
5.8 Clearing PTZ Configurations
Purpose:
You can clear PTZ configurations in this interface, including all presets, patrols,
patterns, privacy masks, PTZ limits and scheduled tasks.
Steps:
1. Enter the Clearing Configuration interface:
Configuration > Advanced Configuration> PTZ > Clear Config
2. Check the checkbox of the items you want to clear.
3. Click
to clear the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
40
Chapter 6 Speed Dome Configuration
6.1 Configuring Local Parameters
Note: The local configuration refers to the parameters of the live view and other
operations using the web browser.
Steps:
1. Enter the Local Configuration interface:
Configuration > Local Configuration
Figure 6-1 Local Configuration Interface
2.

Configure the following settings:
Live View Parameters: Set the protocol type, stream type, image size and live
view performance.
 Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.
TCP: Ensures complete delivery of streaming data and better video quality,
yet the real-time transmission will be affected.
UDP: Provides real-time audio and video streams.
HTTP: Allows the same quality as of TCP without setting specific ports for
streaming under some network environments.
MULTICAST: It’s recommended to select the protocol type to
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
41
User Manual of Network Speed Dome


when using the Multicast function. For other information about Multicast,
refer to Section 6.3.1 Configuring TCP/IP Settings.
 Live View Performance: Set the live view performance to Least Delay,
Balanced or Best Fluency.
Note: Please set Live View Performance as Best Fluency for the high frame
rate speed dome.
 Rules: You can enable or disable the rules of dynamic analysis for motion
here.
Record File Settings: Set the saving path of the video files.
 Record File Size: Select the packed size of manually recorded and downloaded
video files. The size can be set to 256M, 512M or 1G.
 Save record files to: Set the saving path for the manually recorded video files.
 Save downloaded files to: Set the saving path for the downloaded video files
in
interface.
Picture and Clip Settings: Set the saving paths of the captured pictures and
clipped video files.
 Save snapshots in live view to: Set the saving path of the manually captured

pictures in
interface.
Save snapshots when playback to: Set the saving path of the captured

pictures in
interface.
Save clips to: Set the saving path of the clipped video files in
interface.
Note: You can click
to change the directory for saving video files, clips
and pictures.
3. Click
to save the settings.
6.2 Configuring Time Settings
Purpose:
You can follow the instructions in this section to configure the time which can be
displayed on the video. There are Time Zone, Time Synchronization, Daylight Saving
Time(DST) functions for setting the time. Time Synchronization consists of auto
mode by Network Time Protocol(NTP) server and manual mode.
To enter the Time Settings interface:
Configuration > Basic Configuration > System > Time Settings
Or Configuration > Advanced Configuration > System > Time Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
42
User Manual of Network Speed Dome
Figure 6-2 Time Settings
 Configuring Time Synchronization by NTP Server
(1) Check the checkbox to enable the NTP function.
(2) Configure the following settings:
Server Address: IP address of NTP server.
NTP Port: Port of NTP server, 123 by default.
Interval: The time interval between the two synchronizing actions by NTP server.
It can be set from 1 to 10080 minutes.
Figure 6-3 Time Sync by NTP Server
Note: If the speed dome is connected to a public network, you should use a NTP
server that has a time synchronization function, such as the server at the National
Time Center (IP Address: 210.72.145.44). If the speed dome is set in a customized
network, NTP software can be used to establish a NTP server for time
synchronization.
 Configuring Time Synchronization Manually
(1) Check the Manual Time Sync. checkbox.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
43
User Manual of Network Speed Dome
(2) Click
to set the system time from the pop-up calendar.
(3) Click
to save the settings.
Note: You can also check the Sync. with computer time checkbox to synchronize the
time of the speed dome with the time of your computer.
Figure 6-4 Time Sync Manually
 Select the Time Zone
Purpose:
When the speed dome is taken to another time zone, you can use the Time Zone
function to adjust the time. The time will be adjusted according to the original
time and the time difference between the two time zones.
From the Time Zone drop-down menu as shown in Figure 6-5, select the Time
Zone in which the speed dome locates.
Figure 6-5 Time Zone Settings
 Configuring Daylight Saving Time (summer time)
Purpose:
If there is the habit of adjusting clocks forward in your country in certain time
period of a year, you can turn this function on. The time will be adjusted
automatically when the Daylight Saving Time(DST) comes.
Steps:
(1) Enter the DST interface by Configuration > Advanced Configuration >
System > DST
(2) Check
to enable the DST function.
(3) Set the date of the DST period.
(4) Click
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
44
User Manual of Network Speed Dome
Figure 6-6 DST Settings
6.3 Configuring Network Settings
6.3.1 Configuring TCP/IP Settings
Purpose:
TCP/IP settings must be properly configured before you operate the speed dome over
network. IPv4 and IPv6 are both supported.
Steps:
1. Enter TCP/IP Settings interface:
Configuration > Basic Configuration > Network > TCP/IP
Or Configuration > Advanced Configuration > Network > TCP/IP
Figure 6-7 TCP/IP Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
45
User Manual of Network Speed Dome
2. Configure the NIC settings, including the IPv4(IPv6) Address, IPv4(IPv6) Subnet
Mask and IPv4(IPv6) Default Gateway.
3. Click
to save the above settings.
Notes:
 If the DHCP server is available, you can check
to automatically obtain
an IP address and other network settings from that server.
 The valid value range of Maximum Transmission Unit(MTU) is 500 ~ 9676. The
default value is 1500.
 The Multicast sends a stream to the multicast group address and allows multiple
clients to acquire the stream at the same time by requesting a copy from the
multicast group address.
Before utilizing this function, you have to enable the Multicast function of your
router and configure the gateway of the network speed dome.
 If the DNS server settings are required for some applications (e.g., sending
email), you should properly configure the Preferred DNS Server and Alternate
DNS server.
Figure 6-8 DNS Server Settings
Note: The router must support the route advertisement function if you select Route
Advertisement as the IPv6 mode.
6.3.2 Configuring Port Settings
Purpose:
If there is a router and you want to access the speed dome through Wide Area
Network (WAN), you need to forward the 3 ports for the speed dome.
Steps:
1. Enter the Port Settings interface:
Configuration > Basic Configuration > Network > Port
Or Configuration > Advanced Configuration > Network > Port
Figure 6-9 Port Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
2.
Set the HTTP port, RTSP port and port of the speed dome.
HTTP Port: The default port number is 80.
RTSP Port: The default port number is 554.
HTTPS Port: The default port number is 443.
SDK Port: The default port number is 8000.
3.
Click
46
to save the settings.
6.3.3 Configuring PPPoE Settings
Purpose:
If you have no router but only a modem, you can use Point-to-Point Protocol over
Ethernet (PPPoE) function.
Steps:
1. Enter the PPPoE Settings interface:
Configuration >Advanced Configuration > Network > PPPoE
Figure 6-10 PPPoE Settings
2. Check the Enable PPPoE checkbox to enable this feature.
3. Enter User Name, Password, and Confirm password for PPPoE access.
Note: The User Name and Password should be assigned by your ISP.
4. Click
to save and exit the interface.
6.3.4 Configuring DDNS Settings
Purpose:
If your speed dome is set to use PPPoE as its default network connection, you can
use the Dynamic DNS (DDNS) for network access.
Before you start:
Registration on the DDNS server is required before configuring the DDNS settings of
the speed dome.
Steps:
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
47
1. Enter the DDNS Settings interface:
Configuration > Advanced Configuration > Network > DDNS
Figure 6-11 DDNS Settings
2. Check the Enable DDNS checkbox to enable this feature.
3. Select DDNS Type. Three DDNS types are selectable: IPServer, HiDDNS and
DynDNS.
 DynDNS:
Steps:
(1) Enter Server Address of DynDNS (e.g. members.dyndns.org).
(2) In the Domain text field, enter the domain name obtained from the DynDNS
website.
(3) Enter the Port of DynDNS server.
(4) Enter the User Name and Password registered on the DynDNS website.
(5) Click
to save the settings.
Figure 6-12 DynDNS Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
48

IP Server:
Steps:
(1) Enter the Server Address of the IP Server.
(2) Click
to save the settings.
Note: The Server Address should be entered with the static IP address of the
computer that runs the IP Server software. For the IP Server, you have to apply a
static IP, subnet mask, gateway and preferred DNS from the ISP.
Figure 6-13 IPServer Settings

HiDDNS:
Steps:
(1) Enter the Server Address: www.hik-online.com.
(2) Enter the Domain name of the camera. The domain is the same with the
device alias in the HiDDNS server.
(3) Click
to save the settings.
Figure 6-14 HiDDNS Settings

NO-IP:
Steps:
(1) Enter Server Address of NO-IP.
(2) In the Domain text field, enter the domain name obtained from the NO-IP
website.
(3) Enter the Port of NO-IP server.
(4) Enter the User Name and Password registered on the NO-IP website.
(5) Click
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
49
User Manual of Network Speed Dome
6.3.5 Configuring SNMP Settings
Purpose:
You can use SNMP to get speed dome status and parameters related information.
Before you start:
Before setting the SNMP, please use the SNMP software and manage to receive the
speed dome information via SNMP port. By setting the Trap Address, the speed dome
can send the alarm event and exception messages to the surveillance center.
Note: The SNMP version you select should be the same as that of the SNMP
software.
Steps:
1. Enter the SNMP Settings interface:
Configuration > Advanced Configuration > Network > SNMP
Figure 6-15 SNMP Settings
2. Check the corresponding version checkbox (
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
,
50
User Manual of Network Speed Dome
,
) to enable the feature.
3. Configure the SNMP settings.
Note: The configuration of the SNMP software should be the same as the settings
you configure here.
4. Click
to save and finish the settings.
6.3.6 Configuring 802.1X Settings
Purpose:
The speed dome supports IEEE 802.1X standard.
IEEE 802.1X is a port-based network access control. It enhances the security level of
the LAN. When devices connect to this network with IEEE 802.1X standard, the
authentication is needed. If the authentication fails, the devices don’t connect to the
network.
The protected LAN with 802.1X standard is shown as follows:
Authenticator
Network Dome
Network Switch
Net
Authentication
Server
PC
PC
RADIUS
Server
Figure 6-16 Protected LAN




Before connecting the Network Camera to the protected LAN, please apply a
digital certificate from a Certificate Authority.
The network camera requests access to the protected LAN via the
authenticator (a switch).
The switch forwards the identity and password to the authentication
server(RADIUS server).
The switch forwards the certificate of authentication server to the network
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome

51
camera.
If all the information is validated, the switch allows the network access to
the protected network.
Steps:
1. Connect the network camera to your PC directly with a network cable.
2. Enter the 802.1X Settings interface:
Configuration > Advanced Configuration > Network > 802.1X
Figure 6-17 802.1X Settings
3.
4.
5.
Check the Enable IEEE 802.1X checkbox to enable it.
Configure the 802.1X settings, including user name and password.
Note: The EAP-MD5 version must be identical with that of the router or the
switch.
Enter the user name and password (issued by the CA) to access the server.
6.
Click
7.
Note: The camera reboots when you save the settings.
After the configuration, connect the camera to the protected network.
to finish the settings.
6.3.7 Configuring QoS Settings
Purpose:
QoS (Quality of Service) can help solve the network delay and network congestion by
configuring the priority of data sending.
Steps:
1. Enter the QoS Settings interface:
Configuration >Advanced Configuration > Network > QoS
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
52
User Manual of Network Speed Dome
Figure 6-18 QoS Settings
2.
Configure the QoS settings, including video/audio DSCP, event/alarm DSCP and
Management DSCP.
The valid DSCP value ranges from 0 to 63. The DSCP value is bigger, the priority is
higher.
3.
Click
to save the settings.
Notes:
 Make sure that you enable the QoS function of your network device (such as a
router).
 It will ask for a reboot for the settings to take effect.
6.3.8 Configuring FTP Settings
Purpose:
You can set a FTP server and configure the following parameters for uploading
captured pictures.
Steps:
1. Enter the FTP Settings interface:
Configuration >Advanced Configuration > Network > FTP
Figure 6-19 FTP Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
2.
53
Configure the FTP settings, including server address, port, user name, password,
directory and upload type.
 Setting the directory in FTP server for saving files:
In the Directory Structure field, you can select the root directory, parent
directory and child directory.
 Root directory: The files will be saved in the root of FTP server.
 Parent directory: The files will be saved in a folder in FTP server. The
name of folder can be defined as shown in following Figure 6-20.
Figure 6-20 Parent Directory
 Child directory: It is a sub-folder which can be created in the parent
directory. The files will be saved in a sub-folder in FTP server. The name of
folder can be defined as shown in following Figure 6-21.
Figure 6-21 Child Directory

3.
Upload type: To enable uploading the captured picture to the FTP server.
Click
to save the settings.
Note: If you want to upload the captured pictures to FTP server, you also have to
enable the continuous snapshot or event-triggered snapshot in Snapshot
interface. For detailed information, please refer to the Section 7.3 Configuring
Snapshot Settings.
6.3.9 Configuring NAT Settings
 UPnP
Universal Plug and Play (UPnP) is a networking architecture that provides
compatibility among networking equipment, software and other hardware devices.
With the UPnP function enabled, you don’t need to configure the port mapping for
each port, and the camera is connected to the Wide Area Network via the router.
Steps:
1. Enter the UPnP settings interface.
Configuration >Advanced Configuration > Network > NAT
2. Check the Enable UPnP checkbox
3. Add a Friendly Name.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
54
Figure 6-22 Configure UPnP Settings
4.
Click
to save the settings.
 Port Maping
Steps:
1. Check the Enable Port Mapping checkbox
2. Select the Port Mapping Mode as Auto or Manual.
3. If in Manual mode, you can check the checkbox of HTTP, RTSP or SDK port
according to your demand.
4.
Click
to save the settings.
6.3.10 Configuring Email Settings
Purpose:
The system can be configured to send an Email notification to all designated
receivers if an alarm event is detected, e.g., motion detection event, video loss,
tamper-proof, etc.
Before you start:
Please configure the DNS Server settings under Basic Configuration > Network >
TCP/IP or Advanced Configuration > Network > TCP/IP before using the Email
function.
Steps:
1. Enter the Email Settings interface:
Configuration > Advanced Configuration > Network > Email
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
55
Figure 6-23 Email Settings
2.
Configure the following settings:
Sender: The name of the email sender.
Sender’s Address: The email address of the sender.
SMTP Server: The SMTP Server IP address or host name (e.g.,
smtp.263xmail.com).
SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25.
Enable SSL: Check the checkbox to enable SSL if it is required by the SMTP
server.
Attached Image: Check the checkbox of Attached Image if you want to send
emails with attached alarm images.
Interval: The interval refers to the time between two actions of sending attached
pictures.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
56
Authentication (optional): If your email server requires authentication, check
this checkbox to use authentication to log in to this server and enter the login
user name and password.
Receiver: Select the receiver to which the email is sent. Up to 2 receivers can be
configured.
Receiver: The name of the user to be notified.
Receiver’s Address: The email address of user to be notified.
3.
Click
to save the settings.
6.4 Configuring Video and Audio Settings
6.4.1 Configuring Video Settings
Steps:
1. Enter the Video Settings interface:
Configuration >Basic Configuration > Video / Audio > Video
Or Configuration > Advanced Configuration > Video / Audio > Video
Figure 6-24 Configure Video Settings
2.
Select the Stream Type of the speed dome to main stream (normal), sub-stream
or third stream.
The main stream is usually for recording and live viewing with good bandwidth,
and the sub-stream can be used for live viewing when the bandwidth is limited.
Refer to the Section 6.1 Configuring Local Parameters for switching the main
stream and sub-stream for live viewing.
3. You can customize the following parameters for the selected main stream or
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
57
sub-stream:
Video Type:
Select the stream type to video stream, or video & audio composite stream. The
audio signal will be recorded only when the Video Type is Video & Audio.
Resolution:
Select the resolution of the video output.
Bitrate Type:
Select the bitrate type to constant or variable.
Video Quality:
When bitrate type is selected as Variable, 6 levels of video quality are selectable.
Frame Rate:
The frame rate is to describe the frequency at which the video stream is updated
and it is measured by frames per second (fps). A higher frame rate is
advantageous when there is movement in the video stream, as it maintains
image quality throughout.
Max. Bitrate:
Set the max. bitrate to 32~16384 Kbps. The higher value corresponds to the
higher video quality, but the higher bandwidth is required.
Video Encoding:
The Video Encoding standard can be set to H.264 or MJPEG.
Profile:
You can set the profile level to High Profile, Main Profile or Basic Profile.
I Frame Interval:
Set the I-Frame interval from 1 to 400.
4.
Click
to save the settings.
6.4.2 Configuring Audio Settings
Steps:
1. Enter the Audio Settings interface
Configuration > Basic Configuration > Video / Audio > Audio
Or Configuration > Advanced Configuration > Video / Audio > Audio
Figure 6-25 Audio Settings
2.
Configure the following settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
58
Audio Encoding: G.711ulaw, G.711alaw and G.726 selectable.
3.
Click
to save the settings.
6.4.3 Configuring ROI Settings
Before you start:
ROI (Region of Interest) encoding is used to enhance the quality of images which are
specified in advance.
Stream Type:
You can set the ROI function for main stream, sub stream or third stream. Select a
stream type and then configure the ROI settings.
 Fixed Region: Draw several fixed areas and apply the ROI function on them.
Steps:
1. Enter the ROI Settings interface
Configuration > Advanced Configuration > Video / Audio > ROI
2. Select a Region No..
3. Check the check box of Enable under Fixed Region.
4.
Click
5.
Adjust the Enhance the level from 1 to 6. The higher the value, the better image
quality in the red frame.
Enter a Region Name and click Save to save the settings.
6.
and draw a red frame in the live view image.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
59
Figure 6-26 Region of Interest

Dynamic Tracking: The center area of the tracking scene is specified ROI function
by default. When the speed dome starts smart tracking, the quality in the image
center is enhanced.
Steps:
1. Check the check box of Enable under Dynamic Tracking.
2. Adjust the Enhance the level from 1 to 6. The higher the value, the better the
ROI quality.
3. Click Save to save the settings.
6.5 Configuring Image Settings
6.5.1 Configuring Display Settings
Purpose:
You can set the image quality of the speed dome, including brightness, contrast,
saturation, sharpness, etc.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
60
Notes:


The parameters in Display Settings interface vary depending on the models
of speed dome.
You can double click the live view to enter full screen mode and double click
it again to exit.
Steps:
1. Enter the Display Settings interface:
Configuration > Basic Configuration> Image> Display Settings
Or Configuration > Advanced Configuration> Image> Display Settings
2. Set the image parameters of the speed dome.
Figure 6-27 Display Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
61
User Manual of Network Speed Dome
Brightness
This feature is used to adjust brightness of the image. The value ranges from 0 to
100.
Contrast
This feature enhances the difference in color and light between parts of an image.
The value ranges from 0 to 100.
Saturation
This feature is used to adjust color saturation of the image. The value ranges from 0
to 100.
Limit Gain
This feature is used to adjust gain of the image. The value ranges from 0 to 100.
Sharpness
Sharpness function enhances the detail of the image by sharpening the edges in the
image. The value ranges from 0 to 100.
Note: This function varies depending on the models of speed dome.
Focus Mode
The Focus Mode can be set to Auto, Manual, Semi-auto.
 Auto:
The speed dome focuses automatically at any time according to objects in the scene.
 Semi-auto:
The speed dome focuses automatically only once after panning, tilting and zooming.
 Manual:
In Manual mode, you need to use
on the control panel to focus
manually.
Min. Focus Distance
This function is used to limit the minimum focus distance. The value can be set to
1.5m, 3m, 6m, 10cm and 50cm.
Note: The minimum focus value varies depending on the models of speed dome.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
62
User Manual of Network Speed Dome
Exposure Mode
The Exposure Mode can be set to Auto, Iris Priority, Shutter Priority, Manual.
 Auto:
The iris, shutter and gain values will be adjusted automatically according to the
brightness of the environment.
 Iris Priority:
The value of iris needs to be adjusted manually. The shutter and gain values will be
adjusted automatically according to the brightness of the environment.
Figure 6-28 Manual Iris

Shutter Priority:
The value of shutter needs to be adjusted manually. The iris and gain values will be
adjusted automatically according to the brightness of the environment.
Figure 6-29 Manual Shutter

Gain Priority:
The value of gain needs to be adjusted manually. The shutter and iris values will be
adjusted automatically according to the brightness of the environment.
Figure 6-30 Manual Gain

Manual:
In Manual mode, you can adjust the values of Gain, Shutter, Iris manually.
Note: This function varies depending on the models of speed dome.
Smart IR
If the IR light is on and the image center is overexposure, you can enable this
function.
Video Standard
You can set the Video Standard to 50hz(PAL) or 60hz(NTSC) according to the video
system in your country.
Note: This function varies depending on the models of speed dome.
Day/Night Switch
The Day/Night Switch mode can be set to Auto, Day and Night.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
63
User Manual of Network Speed Dome

Auto:
In Auto mode, the day mode and night mode can switch automatically according to
the light condition of environment. The switching sensitivity can be set to Low,
Normal, High.
Figure 6-31 Auto Mode Sensitivity

Day:
In Day mode, the speed dome displays color image. It is used for normal lighting
conditions.
 Night:
In Night mode, the image is black and white. Night mode can increase the sensitivity
in low light conditions.
Notes:
 When the IR Light Mode is auto, the day/night mode is adjusted
automatically according to the IR Light Mode. Manually setting the
day/night mode is invalid.
 When the IR Light Mode is manual and the IR Light Bright is 0, you can set
the day/night mode manually.
 When the IR Light Mode is manual and the IR Light Bright is not 0, the night
mode is set as the default mode. Manually setting the day/night mode is
invalid.
Mirror
If you turn the MIRROR function on, the image will be flipped. It is like the image in
the mirror. The flip direction can be set to OFF, LEFT/RIGHT, UP/DOWN or CENTER.
Note: This function varies depending on the models of speed dome.
WDR (Wide Dynamic Range)
The wide dynamic range (WDR) function helps the camera provide clear images even
under back light circumstances. When there are both very bright and very dark areas
simultaneously in the field of view, WDR balances the brightness level of the whole
image and provide clear images with details.
You can enable or disable the WDR function as shown in Figure 6-32. The wide
dynamic level ranges from 0 to 100.
Figure 6-32 WDR
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
64
User Manual of Network Speed Dome
Note: This function varies depending on the models of speed dome.
Slow Shutter
This function can be used in underexposure condition. It lengthens the shutter time
to ensure full exposure. The slow shutter value can be set to Low, Normal and High.
Figure 6-33 Slow Shutter
Lens Initialization
The lens operates the movements for initialization when you check the check box of
Lens Initialization.
BLC
If there’s a bright backlight, the subject in front of the backlight appears silhouetted
or dark. Enabling BLC(back light compensation) function can correct the exposure of
the subject. But the backlight environment is washed out to white.
White Balance
The White Balance mode can be set to Auto, MWB, Outdoor, Indoor, Fluorescent
Lamp, Sodium Lamp and Auto-Track.
 Auto:
In Auto mode, the camera retains color balance automatically according to the
current color temperature.
 Manual White Balance:
In MWB mode, you can adjust the color temperature manually to meet your own
demand as shown in Figure 6-34.
Figure 6-34 Manual White Balance

Outdoor
You can select this mode when the speed dome is installed in outdoor environment.
 Indoor
You can select this mode when the speed dome is installed in indoor environment.
 Fluorescent Lamp
You can select this mode when there are fluorescent lamps installed near the speed
dome.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
65

Sodium Lamp
You can select this mode when there are sodium lamps installed near the speed
dome.
 Auto-Track
In Auto-Track mode, white balance is continuously being adjusted in real-time
according to the color temperature of the scene illumination.
Note: This function varies depending on the models of speed dome.
3D Digital Noise Reduction
You can enable or disable the 3D Digital Noise Reduction function as shown in Figure
6-35. The level ranges from 0 to 100.
Figure 6-35 3D Digital Noise Reduction
Note: This function varies depending on the models of speed dome.
De-fog Mode
When there is fog in the image, you can enable this function to get clear image.
Zoom Limit
You can set Zoom Limit value to limit the maximum value of zooming. The value can
be set to 20, 40, 80, 160 and 320.
Note: This function varies depending on the models of speed dome.
IR Light Mode
IR light mode can be set to Auto and Manual.
 Auto: The brightness of the infrared light will be adjusted automatically. IR Light
Sensitivity value ranges from 0 to 100.
 Manual: you need to adjust the brightness value of infrared light manually. IR
Light Bright value ranges from 0 to 100.
Note: For detailed parameters configuration of IR light, you can enter the OSD menu
by calling the special preset 95.
Chroma Suppress
The Chroma Suppress level ranges from 0 to 100 as shown in Figure 6-36.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
66
Figure 6-36 Chroma Suppress
Note: This function varies depending on the models of speed dome.
HLC
HLC (High Light Compensation) makes the camera identify and suppress the strong
light sources that usually flare across a scene. This makes it possible to see the detail
of the image that would normally be hidden.
Local Output
You can select the output mode to ON or OFF.
6.5.2 Configuring OSD Settings
Purpose:
The speed dome supports following on screen displays:
Zoom: Identifies the amount of magnification.
Direction: Displays panning and tilting direction, with the format of PXXX TXXX. The
XXX following P indicates the degrees in pan direction, while the XXX following T
indicates the degrees in tilt position.
Time: Supports for time display.
Preset Title: Identifies preset being called.
Camera Name: Identifies the name of speed dome.
You can customize the on screen display of time.
Steps:
1. Enter the OSD Settings interface:
Configuration > Advanced Configuration > Image > OSD Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
67
User Manual of Network Speed Dome
Figure 6-37 OSD Settings
2. Check the corresponding checkbox to select the display of speed dome name,
date or week if required.
3. Edit the speed dome name in the text field of Camera Name.
4. Select from the drop-down list to set the time format, date format and display
mode.
5. You can use the mouse to click and drag the text frame
view window to adjust the OSD position.
Figure 6-38 Adjust OSD Location
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
in the live
68
User Manual of Network Speed Dome
6. Click
to activate above settings.
6.5.3 Configuring Text Overlay Settings
Purpose:
You can customize the text overlay.
Steps:
1. Enter the Text Overlay Settings interface:
Configuration > Advanced Configuration > Image > Text Overlay
2. Check the checkbox in front of textbox to enable the on-screen display.
3. Input the characters in the textbox.
4. Use the mouse to click and drag the red text frame
in the live view
window to adjust the text overlay position.
5. Click
.
Note: There are up to 8 text overlays configurable.
Figure 6-39 Text Overlay Settings
6.6 Configuring and Handling Alarms
Purpose:
This section explains how to configure the network speed dome to respond to alarm
events, including motion detection, external alarm input, video loss, tamper-proof
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
69
and exception. These events can trigger the alarm actions, such as Notify Surveillance
Center, Send Email, Trigger Alarm Output, etc.
For example, when an external alarm is triggered, the network speed dome sends a
notification to an e-mail address.
6.6.1 Configuring Motion Detection
Purpose:
Motion detection is a feature which can trigger alarm actions and actions of
recording videos when the motion occurred in the surveillance scene.
Steps:
1. Set the Motion Detection Area.
Steps:
(1) Enter the motion detection settings interface
Configuration > Advanced Configuration> Events > Motion Detection
(2) Check the checkbox of Enable Motion Detection.
Figure 6-40 Enable Motion Detection
(3) Click
. Click and drag the mouse on the live video image to draw
a motion detection area.
Note: You can draw up to 8 motion detection areas on the same image.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
70
User Manual of Network Speed Dome
(4) Click
to finish drawing.
Note: You can click
2.
to clear all of the areas.
(5) Move the slider
detection.
Set the Arming Schedule for Motion Detection.
Steps:
to set the sensitivity of the
(1) To edit the arming schedule as shown in Figure 6-42, click
in
Figure 6-41.
Figure 6-41 Arming Schedule
(2) Choose the day you want to set the arming schedule as shown in Figure 6-42.
(3) Click
to set the time period for the arming schedule.
(4) After you set the arming schedule, you can click
to copy the
schedule to other days (Optional).
(5) Click
to save the settings.
Note: The time of each period can’t be overlapped. Up to 4 periods can be
configured for each day.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
71
Figure 6-42 Arming Time Schedule
3.
Set the Alarm Actions for Motion Detection.
Purpose:
You can specify the linkage method when an event occurs. The following
contents are about how to configure the different types of linkage method.
Figure 6-43 Linkage Method
Check the checkbox to select the linkage method. Notify surveillance
center, send email, upload to FTP, trigger channel and trigger alarm output
are selectable.
 Notify Surveillance Center
Send an exception or alarm signal to remote management software when
an event occurs.
 Send Email
Send an email with alarm information to a user or users when an event
occurs.
Note: To send the Email when an event occurs, you need to refer to Section
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
72
User Manual of Network Speed Dome
6.3.10 Configuring Email Settings to set the Email parameters.
 Upload to FTP
Capture the image when an alarm is triggered and upload the picture to a
FTP server.
Note: You need a FTP server and set FTP parameters first. Refer to Section
6.3.8 Configuring FTP Settings for setting FTP parameters.
 Trigger Channel
Record a video when an event occurs.
Note: You have to set the recording schedule to realize this function. Please
refer to Section 7.2 Configuring Recording Schedule for settings the
recording schedule.
 Trigger Alarm Output
Trigger one or more external alarm outputs when an event occurs.
Note: To trigger an alarm output when an event occurs, please refer to
Section 6.6.5 Configuring Alarm Output to set the alarm output
parameters.
6.6.2 Configuring Video Loss Alarm
Steps:
1. Enter the Video Loss Setting interface:
Configuration > Advanced Configuration> Events > Video Loss
Figure 6-44 Video Loss
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
73
2. Check the Enable Video Loss Detection checkbox to enable the video loss
detection.
3.
Click
to edit the arming schedule for video loss detection. The
arming schedule configuration is the same as the setting of the arming schedule for
motion detection. Refer to Step 2 Set the Arming Schedule for Motion Detection in
Section 6.6.1.
4. Check the checkbox to select the linkage method taken for the video loss alarm.
Notify surveillance center, send email and trigger alarm output are selectable. Please
Step 3 Set the Alarm Actions for Motion Detection in Section 6.6.1.
5.
Click
to save the settings.
6.6.3 Configuring Tamper-proof Alarm
Purpose:
You can configure the speed dome to trigger the alarm actions when the lens is
covered.
Steps:
1. Enter the Tamper-proof Settings interface:
Configuration > Advanced Configuration > Events > Tamper-proof
Figure 6-45 Tamper-proof Alarm
2.
Check Enable Tamper-proof checkbox to enable the tamper-proof detection.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
74
3. Set the tamper-proof area. Refer to Step 1 Set the Motion Detection Area in
Section 6.6.1 Configuring Motion Detection.
4.
Click
to edit the arming schedule for tamper-proof. The arming
schedule configuration is the same as the setting of the arming schedule for motion
detection. Refer to Step 2 Set the Arming Schedule for Motion Detection in Section
6.6.1 Configuring Motion Detection.
5. Check the checkbox to select the linkage method taken for the tamper-proof.
Notify surveillance center, send email and trigger alarm output are selectable. Please
refer to Step 3 Set the Alarm Actions for Motion Detection in Section 6.6.1
Configuring Motion Detection.
6.
Click
to save the settings.
6.6.4 Configuring External Alarm Input
Steps:
1. Enter the Alarm Input Settings interface:
Configuration > Advanced Configuration> Events > Alarm Input:
2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO
(Normally Open) and NC (Normally Closed).
3.
Edit the name in
name for the alarm input (optional).
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
to set a
User Manual of Network Speed Dome
75
Figure 6-46 Alarm Input Settings
4.
Click
to set the arming schedule for the alarm input. Refer to Step 2
7.
Set the Arming Schedule for Motion Detection in Section 6.6.1 Configuring
Motion Detection.
Check the checkbox to select the linkage method taken for the alarm input. Refer
to Step 3 Set the Alarm Actions for Motion Detection in Section 6.6.1
Configuring Motion Detection.
You can also choose the PTZ linking for the alarm input. Check the relative
checkbox and select the No. to enable Preset Calling, Patrol Calling or Pattern
Calling.
You can copy your settings to other alarm inputs.
8.
Click
5.
6.
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
76
Figure 6-47 Linkage Method
6.6.5 Configuring Alarm Output
Steps:
1. Enter the Alarm Output Settings interface:
Configuration>Advanced Configuration> Events > Alarm Output
2. Select one alarm output channel in the Alarm Output drop-down list.
3.
4.
Set a name in
for the
alarm output (optional).
The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or
Manual. The delay time refers to the time duration that the alarm output
remains in effect after alarm occurs.
5.
Click
to enter the Edit Schedule Time interface. The time schedule
6.
configuration is the same as the settings of the arming schedule for motion
detection. Refer to Step 2 Set the Arming Schedule for Motion Detection in
Section 6.6.1 Configuring Motion Detection.
You can copy the settings to other alarm outputs.
7.
Click
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
77
Figure 6-48 Alarm Output Settings
6.6.6 Handling Exception
The exception type can be HDD full, HDD error, network disconnected, IP address
conflicted and illegal login to the speed domes.
Steps:
1. Enter the Exception Settings interface:
Configuration > Advanced Configuration> Events > Exception
2. Check the checkbox to set the actions taken for the Exception alarm. Refer to
Step 3 Set the Alarm Actions Taken for Motion Detection in Section 6.6.1
Configuring Motion Detection.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
Figure 6-49 Exception Settings
3.
Click
to save the settings.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
78
User Manual of Network Speed Dome
79
Chapter 7 Record Settings
Before you start:
To configure record settings, please make sure that you have the network storage
device within the network or the SD card inserted in your speed dome.
7.1 Configuring NAS Settings
Before you start:
The network disk should be available within the network and properly configured to
store the recorded files, log files, etc.
Steps:
1. Add the network disk
(1) Enter the NAS (Network-Attached Storage) Settings interface:
Configuration > Advanced Configuration > Storage > NAS
Figure 7-1 Add Network Disk
(2) Enter the IP address of the network disk, and the default format of file path is
/dvr/share as shown in Figure 7-1.
Note: The network disk file path name share is user-defined while creating the
DVR network storage. Please refer to the User Manual of NAS for creating the file
path.
(3) Click
to add the network disk.
Note: After having saved successfully, you need to reboot the speed dome to
activate the settings.
2. Initialize the added network disk.
(1) Enter the HDD Settings interface (Advanced Configuration > Storage >
Storage Management), in which you can view the capacity, free space, status,
type and property of the disk.
(2) If the status of the disk is Uninitialized as shown in Figure 7-2, check the
corresponding checkbox to select the disk and click
initializing the disk.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
to start
80
User Manual of Network Speed Dome
Figure 7-2 Initialize Disk
Figure 7-3 Initializing
When the initialization completed, the status of disk will become Normal as
shown in Figure 7-4.
Figure 7-4 View Disk Status
Notes:
 Up to 8 NAS disks can be connected to the speed dome.
 To initialize and use the SD card after insert it to the speed dome, please refer to
the steps of NAS disk initialization.
7.2 Configuring Recording Schedule
Purpose:
There are two kinds of recording for the speed domes: manual recording and
scheduled recording. For the manual recording, refer to Section 4.4 Recording and
Capturing Pictures Manually. In this section, you can follow the instructions to
configure the scheduled recording. By default, the record files of scheduled recording
are stored in the SD card (if supported) or in the network disk.
Steps:
1. Enter the Record Schedule Settings interface:
Configuration > Advanced Configuration> Storage > Record Schedule
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
81
Figure 7-5 Recording Schedule Interface
2. Check the checkbox of Enable Record Schedule to enable scheduled recording.
3. Set the record parameters of the speed dome.
Figure 7-6 Record Parameters

Pre-record: The time you set to start recording before the scheduled time or
the event. For example, if an alarm triggers recording at 10:00, and the
pre-record time is set as 5 seconds, the speed dome starts to record at
9:59:55.
The Pre-record time can be configured as No Pre-record, 5 s, 10 s, 15 s, 20 s,
25 s, 30 s or not limited.
Note: The pre-record time changes according to the video bitrate.
 Post-record: The time you set to stop recording after the scheduled time or
the event. For example, if an alarm triggered recording ends at 11:00, and the
post-record time is set as 5 seconds, the speed dome records until 11:00:05.
The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2 min, 5 min
or 10 min.
 Overwrite: If you enable his function and the HDD is full, the new record files
overwrite the oldest record files automatically.
Note: The Pre-record and Post-record parameters vary depending on the speed
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
82
dome model.
4. Click
to edit the record schedule.
Figure 7-7 Record Schedule
5. Choose the day to set the record schedule.
(1) Set all-day record or segment record:
 If you want to configure the all-day recording, please check the All Day
checkbox.
 If you want to record in different time sections, check the Customize
checkbox. Set the Start Time and End Time.
Note: The time of each segment can’t be overlapped. Up to 4 segments can
be configured.
(2) Select a Record Type. The record type can be Normal, Motion Detection,
Alarm, Motion | Alarm, Motion & Alarm.
 Normal
If you select Normal, the video will be recorded automatically according to
the time of the schedule.
 Record Triggered by Motion Detection
If you select Motion Detection, the video will be recorded when the
motion is detected.
Besides configuring the recording schedule, you have to set the motion
detection area and check the checkbox of Trigger Channel in the Linkage
Method of Motion Detection Settings interface. For detailed information,
please refer to the Step 1 Set the Motion Detection Area in the Section
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
83
User Manual of Network Speed Dome
6.6.1 Configuring Motion Detection.
 Record Triggered by Alarm
If you select Alarm, the video will be recorded when the alarm is triggered
via the external alarm input channels.
Besides configuring the recording schedule, you have to set the Alarm Type
and check the checkbox of Trigger Channel in the Linkage Method of
Alarm Input Settings interface. For detailed information, please refer to
Section 6.6.4 Configuring External Alarm Input.
 Record Triggered by Motion & Alarm
If you select Motion & Alarm, the video will be recorded when the motion
and alarm are triggered at the same time.
Besides configuring the recording schedule, you have to configure the
settings on the Motion Detection and Alarm Input Settings interfaces.
Please refer to Section 6.6.1 and Section 6.6.4 for detailed information.
 Record Triggered by Motion | Alarm
If you select Motion | Alarm, the video will be recorded when the external
alarm is triggered or the motion is detected.
Besides configuring the recording schedule, you have to configure the
settings on the Motion Detection and Alarm Input Settings interfaces.
Please refer to Section 6.6.1 and Section 6.6.4 for detailed information.
Figure 7-8 Edit Record Schedule
(3) Check the checkbox
and click
to copy settings of this
day to the whole week. You can also check any of the checkboxes before the
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
84
User Manual of Network Speed Dome
date and click
(4) Click
.
to save the settings and exit the Edit Record Schedule
interface.
6. Click
to save the settings.
7.3 Configuring Snapshot Settings
Purpose:
You can configure the scheduled snapshot and event-triggered snapshot. You can
upload the captured pictures to a FTP server.
Basic Settings
Steps:
1. Enter the Snapshot Settings interface:
Configuration > Advanced Configuration > Storage > Snapshot
2. Check the Enable Timing Snapshot checkbox to enable continuous snapshot.
Check the Enable Event-triggered Snapshot checkbox to check event-triggered
snapshot.
3. Select the quality of the snapshot.
4. Set the time interval between two snapshots.
5.
Click
to save the settings.
Uploading to FTP
Please make sure that the FTP server is online.
You can follow below configuration instructions to upload the snapshots to FTP.
 Upload continuous snapshots to FTP
Steps:
1) Configure the FTP settings and check
checkbox in FTP
Settings interface. Please refer to Section 6.3.8 Configuring FTP Settings for more
details to configure FTP parameters.
2) Check the Enable Timing Snapshot checkbox.
 Upload event-triggered snapshots to FTP
Steps:
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
85
User Manual of Network Speed Dome
1) Configure the FTP settings and check
checkbox in FTP
Settings interface. Please refer to Section 6.3.8 Configuring FTP Settings for more
details to configure FTP parameters.
2) Check
checkbox in Motion Detection Settings or Alarm Input
interface. Please refer to Step 3 Set the Alarm Actions Taken for Motion
Detection in Section 6.6.1 Configuring Motion Detection, or Step 4 Configuring
External Alarm Input in Section 6.6.1 Configuring Motion Detection.
3) Check the Enable Event-triggered Snapshot checkbox.
Figure 7-9 Snapshot Settings
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
86
User Manual of Network Speed Dome
Chapter 8 Playback
Purpose:
This section explains how to view the remotely recorded video files stored in the
network disks or SD cards.
Task 1: To play back the video files
Steps:
1.
Click
on the menu bar to enter playback interface.
Figure 8-1 Playback Interface
2.
Select the date and click
.
Figure 8-2 Search Video
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
87
User Manual of Network Speed Dome
3.
Click
to play the video files found on this date.
The toolbar on the bottom of Playback interface can be used to control playing
process.
Figure 8-3 Playback Toolbar
Table 8-1 Description of the buttons
Button
Operation
Button
Play
Operation
Capture a picture
Pause
/
Stop
/
Start/Stop clipping video
files
Audio on and adjust
volume/Mute
Speed down
Download video files
Speed up
Download captured
pictures
Display
playback
status
Playback by frame
Note: You can choose the file paths locally for downloaded playback video files and
pictures in Local Configuration interface. Please refer to Section 6.1 Configuring Local
Parameters for details.
Drag the progress bar with the mouse to locate the exact playback point. You can
also input the time and click
time field. You can also click
to locate the playback point in the Set playback
to zoom out/in the progress bar.
Figure 8-4 Set Playback Time
Figure 8-5 Progress Bar
The different colors of the video on the progress bar stand for the different video
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
88
User Manual of Network Speed Dome
types as shown in Figure 8-6.
Figure 8-6 Video Types
Task 2: To download the video files
Steps:
1.
Click
on the playback interface. The pop-up menu is shown in Figure 8-7.
2.
Set the start time and end time. Click Search. The corresponding video files are
listed on the left.
Figure 8-7 Video Downloading interface
3.
Check the checkbox
4.
Click
in front of the video files that you need to download.
to download the video files.
Notes:

The progress ratio

You can click

The total number

The video files are not all listed on one page. You can click
displays the downloading ratio of the video file.
to stop the downloading.
displays the amount of the video files.
to turn pages.
Task 3: To download the captured pictures
Steps:
1.
Click
on the playback interface. The pop-up menu is shown in Figure 8-8.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
89
User Manual of Network Speed Dome
2.
3.
Set the linkage type of capturing the pictures as timing, alarm, motion, etc..
Set the start time and end time. Click Search. The corresponding picture files are
listed on the left.
4.
Check the checkbox
5.
Click
in front of the files that you need to download.
to download the files.
Figure 8-8 Picture Downloading interface
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
90
User Manual of Network Speed Dome
Chapter 9 Log Searching
Purpose:
The operation, alarm, exception and information of the speed dome can be stored in
log files. You can also export the log files on your demand.
Before you start:
Please configure network storage for the speed dome or insert a SD card in the speed
dome.
Steps:
1. Click
on the menu bar to enter log searching interface.
Figure 9-1 Log Searching Interface
2. Set the log search conditions to specify the search, including the Major Type,
Minor Type, Start Time and End Time as shown in Figure 9-2.
3. Click
to search log files. The matched log files will be displayed on
the Log interface.
Figure 9-2 Log Searching
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
91
User Manual of Network Speed Dome
4. To export the log files, click
to save the log files in your computer.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
92
Chapter 10 Others
10.1 Managing User Accounts
Enter the User Management interface:
Configuration >Basic Configuration> Security > User
Or Configuration > Advanced Configuration> Security > User
The admin user has access to create, modify or delete other accounts. Up to 32 user
accounts can be created.
Figure 10-1 User Information
 Add a User
Steps:
1.
Click
to add a user.
2. Input the new User Name, select Level and input Password.
Note: The level indicates the permissions you give to the user. You can define the
user as Operator or User.
3. In the Basic Permission field and Camera Configuration field, you can check or
uncheck the permissions for the new user.
4.
Click
to finish the user addition.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
93
User Manual of Network Speed Dome
Figure 10-2 Add a User
 Modify a User
Steps:
1. Left-click to select the user from the list and click
.
2. Modify the User Name, Level or Password.
3. In the Basic Permission field and Camera Configuration field, you can check or
uncheck the permissions.
4. Click
to finish the user modification.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
94
User Manual of Network Speed Dome
Figure 10-3 Modify a User
 Delete a User
Steps:
1. Left-click the user name you want to delete and click
2. Click
.
on the pop-up dialogue box to delete the user.
Figure 10-4 Delete a User
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
95
10.2 Configuring RTSP Authentication
Purpose:
You can specifically secure the stream data of live view.
Steps:
1. Enter the RTSP Authentication interface:
Configuration> Advanced Configuration> Security > RTSP Authentication
Figure 10-5 RTSP Authentication
2.
Select the Authentication type basic or disable in the drop-down list to enable
or disable the RTSP authentication.
3.
Click
to save the settings.
10.3 Configuring Anonymous Visit
When you enable this function, you can log into the camera without a username and
password.
In login interface, check the Anonymous checkbox and click Login to enter the
camera as shown in Figure 10-7.
Figure 10-6 Anonymous Login
Figure 10-7 Login Interface
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
96
10.4 Configuring IP Address Filter
With this function on, the camera allows certain IP addresses whether to log in or
not.
Filter Type
Description
Forbid the IP addresses added in
Forbidden
the IP Address Filter interface to
log in.
Allow only the IP addresses
Allowed
added in the IP Address Filter
interface to log in.
Figure 10-8 IP Address Filter
10.5 Viewing Device Information
Enter the Device Information interface:
Configuration > Basic Configuration> System > Device Information
Or Configuration > Advanced Configuration> System > Device Information
In the Device Information interface, you can edit the Device Name.
Other information of the network speed dome, such as Model, Serial No., Firmware
Version, Encoding Version, Number of Channels, Number of HDDs, Number of Alarm
Input and Number of Alarm Output are displayed. The information cannot be
changed in this menu. It is the reference for maintenance or modification in future.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
Figure 10-9 Device Information
10.6 Maintenance
10.6.1 Rebooting the Speed Dome
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance:
2.
Click
to reboot the network speed dome.
Figure 10-10 Reboot the Device
10.6.2 Restoring Default Settings
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
97
98
User Manual of Network Speed Dome
2.
Click
Note: Clicking
or
to restore the default settings.
restores all the parameters to default settings including
the IP address and user information. Please use this button with caution.
Figure 10-11 Restore Default Settings
10.6.3 Importing/Exporting Configuration File
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance
2.
Click
to select the local configuration file and then click
to start importing configuration file.
Note: You need to reboot the speed dome after importing configuration file.
3.
Click
and set the saving path to save the configuration file in local
storage.
Figure 10-12 Import/Export Configuration File
10.6.4 Upgrading the System
Steps:
1. Enter the Maintenance interface:
Configuration > Basic Configuration> System > Maintenance
Or Configuration > Advanced Configuration> System > Maintenance
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
User Manual of Network Speed Dome
2.
Click
99
to select the local upgrade file and then click
to start remote upgrade.
Note: The upgrading process will take 1 to 10 minutes. Please don't disconnect
power of the speed dome during the process. The speed dome reboots automatically
after upgrading.
Figure 10-13 Remote Upgrade
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
100
User Manual of Network Speed Dome
10.7 RS-485 Settings
Purpose:
The RS-485 serial port is used to control the PTZ of the camera. The configuring of
the PTZ parameters should be done before you control the PTZ unit.
Steps:
1. Enter RS-485 parameter setting interface:
Configuration> Advanced Configuration> System > RS485
Figure 10-14 RS-485 Settings
2.
Set the RS-485 parameters and click
to save the settings.
By default, the Baud Rate is set as 9600 bps, the Data Bit is 8, the stop bit is 1 and
the Parity and Flow Control is None.
Note: The Baud Rate, PTZ Protocol and PTZ Address parameters of the speed dome
should be exactly the same as those of the remote control device.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
101
User Manual of Network Speed Dome
Appendix
Appendix 1 SADP Software Introduction
 Description of SADP
SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free
online device search tool. It searches the active online devices within your subnet
and displays the information of the devices. You can also modify the basic network
information of the devices using this software.
 Search active devices online
 Search online devices automatically
After launch the SADP software, it automatically searches the online devices
every 15 seconds from the subnet where your computer locates. It displays
the total number and information of the searched devices in the Online
Devices interface. Device information including the device type, IP address
and port number, etc. will be displayed.
Figure A.1.1 Searching Online Devices
Note: Device can be searched and displayed in the list in 15 seconds after it went
online; it will be removed from the list in 45 seconds after it went offline.
 Search online devices manually
You can also click
to refresh the online device list manually. The
newly searched devices will be added to the list.
Note: You can click
or
on each column heading to order the
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
102
User Manual of Network Speed Dome
information; you can click
to expand the device table and hide the
network parameter panel on the right side, or click
to show the
network parameter panel.
 Modify network parameters
Steps:
1. Select the device to be modified in the device list and the network parameters of
the device will be displayed in the Modify Network Parameters panel on the
right side.
2. Edit the modifiable network parameters, e.g. IP address and port number.
3. Enter the password of the admin account of the device in the Password field and
click
to save the changes.
Figure A.1.2 Modify Network Parameters

Restore default password
Steps:
1. Contact our technical engineers to get the serial code.
Note: Serial code is a series of characters combined by the start time and the serial
number of the device.
2. Input the code in the Serial code field and click
password.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
to restore the default
User Manual of Network Speed Dome
103
Appendix 2 Port Mapping
The following settings are for TP-LINK router (TL-R410). The settings vary depending
on different models of routers.
Steps:
1. Select the WAN Connection Type, as shown below:
Figure A.2.1 Select the WAN Connection Type
2. Set the LAN parameters of the router as in the following figure, including IP
address and subnet mask settings.
Figure A.2.2 Set the LAN parameters
3. Set the port mapping in the virtual severs of Forwarding. You need to forward
ports 80, 8000, 8200~8210 and 554 for a speed dome.
Notes:


You can change 80, 8000 and 554 ports value in the speed dome with web
browser or client software.
In the speed dome, the 8200~8210 ports change with the 8000 port with a
constant value of 200. E.g. if the 8000 port is changed to 8005, then the
8200~8210 ports should be changed to 8205~8215.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
104
User Manual of Network Speed Dome
Example:
When the speed domes are connected to the same router, you can forward the
ports of a speed dome as 80, 8000, 8200~8210 and 554 with IP address
192.168.1.23, and the ports of another speed dome as 81, 8001, 8201~8211 and
555 with IP 192.168.1.24. Refer to the steps as below:
Steps:
1. As the settings mentioned above, forward the port 80, 8000, 8200~8210 and 554
for the network speed dome at 192.168.1.23
2. Forward the port 81, 8001, 8201~8211 and 555 for the network speed dome at
192.168.1.24.
3. Enable ALL or TCP protocols.
4. Check the Enable checkbox and click
.
Figure A.2.3 Port Mapping
Note: The port of the network speed dome cannot conflict with other ports. For
example, some web management port of the router is 80. Change the speed dome
port if it is the same as the management port.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Download PDF
Similar pages