NO WEB ACCESS Failure to do so will invalidate your warranty. PIE

LIMITED WARRANTY
All equipment which is sold under ANVIL trademark and used for
commercial purposes is warranted against defects in materials and
workmanship. The warranty runs for one year from the date of original installation and is for the benefit of the original purchaser only.
All other Warranties ,expressed or implied , statutory or otherwise,
including without limitations any implied Warranty of Merchantability
or fitness for purpose are excluded .The Seller shall in no event be
liable for direct,indirect or consequential damages in connection with
ANVIL commercial products.
PIE WARMER MINI
The Sellers obligation under this Warranty is limited to the repair of defects without charge. Defective units must be taken or
shipped,transportation charges prepaid,to ANVIL.
This Warranty is not effective if damage occurs because of
accident,carelessness,improper installation,lack of proper setup,supervision when required or if the equipment is installed or
operated in any manner contrary to the installation and operating
instructions. In these cases,repairs will be made at a reasonable
cost. Work performed by unauthorized personnel or unauthorized
service agencies voids this Warranty.
NB:
INSTALLATION OPERATION AND CARE OF
PIE WARMER MINI
MODELS: PWK0007 R01
REGISTER ON-LINE TODAY
Register your warranty on-line now at www.anvilworld.com
NO WEB ACCESS
If you do not have access to the Web. Kindly register by completing
the warranty registration form and fax it to the ANVIL office in the
country of purchase.
Failure to do so will invalidate your warranty.
4-INS-PWK0007 R01
UNPACKING
Unpack the product and check for any damage incurred during
transit. This should be reported to the responsible carrier, railway or
postal authority, and a request for a damage report should be made.
THESE INSTRUCTIONS MUST BE FOLLOWED FOR US TO
GUARANTEE OUR FULL SUPPORT OF YOUR CLAIM FOR
PROTECTING AGAINST LOSS FROM CONCEALED DAMAGE. THE FORM FOR FILING SUCH A CLAIM WILL BE
PROVIDED BY THE CARRIER.
GENERAL INSTALLATION AND OPERATION
INSTRUCTIONS
1. This unit has been designed for countertop display of food such
as pies and sausage rolls . The heater system ensures that the
products placed inside can be stored and served at the correct
temperature and humidity. An internal lighting system enhances
the products displayed.
2. There are three wire shelves provided with the unit. The wire
shelves must be positioned with the four legs inside the support
runner this prevents the shelf from sliding forward or backward.
3. Install the unit in the most convenient location for the ease of
cleaning, maintenance and point of sale of display.
4. The temperature is preset to the required temperature. When
the switch is in the ‘ON’ position the unit has power, the interior
lamps will switch on and heating element will energise.
5. There is a removable crumb tray positioned at the front of the
unit
MODEL: PIE WARMER MINI
MODEL CODE :PWK0007 R01
Part
No.
Description
1
PIE WARMER SHELF
2
TOP COVER
3
SHELF RUNNER
4
OUTER ENCLOSURE
5
FRONT GLASS DOOR
6
ANVIL AIRE LOGO
7
FOOT
8
ELEMENT
9
SHELF RUNNER
10
PORCELAIN LAMP HOLDER
11
COOL WHITE ENERGY SAVER LIGHT BULB
12
CRUMB TRAY
13
THERMOSTAT
14
NON-ILLUMINATED ROCKER SWITCH
15
CABLE GRIP
16
MAGNETIC DOOR CATCH
17
POWER CORD
18
REAR GLASS DOOR
19
PERANO BUTT HINGE
20
PIE WARMER KNOB
SPECIFIC OPERATING INSTRUCTIONS
1. The unit is provided with a small humidity pan and mounted in the internal bottom plate. Should humidity be required this must be filled with 600 ML of water and the
level must be monitored on a regular basis.
2. For servicing, the unit is provided with a removable bottom panel.
3. For changing the top light bulb, the four screws holding
the top lid must be removed. Lift off the lid and the light
fitting is accessible.
WARNING
EXPLODED DIAGRAM
PIE WARMER MINI
MODEL: PWK0007 R01
9
10
20
Hot surfaces and food can burn skin. Allow the hot surfaces to cool
before handling
13
15
12
14
8
16
17
7
THIS APPLIANCE SHOULD NOT BE CLEANED WITH
A WATER JET OR IMMERSED IN WATER. USE ONLY
A DAMP CLOTH OR SPONGE DIPPED IN SOAPY
WATER. DO NOT USE STEEL-WOOL WHICH WILL
MARK THE BRIGHT STAINLESS STEEL FINISH
6
4
2
5
3
3.
Always ensure that the unit is disconnected from the mains
power supply before cleaning
This appliance should not be cleaned with a water jet or immersed in water. Use only a damp cloth or sponge dipped in
soapy water.
Wipe off the unit with a dry cloth and wait at least half an hour
before re – connecting to the mains outlet.
1
2.
18
CLEANING
1.
11
19
19
Burn Hazard.
Do not touch hot food,liquid or heating surfaces
while equipment is heating or operating
LEGEND
DESCRIPTION
PART NUMBER
B1
THERMOSTAT
1-THERM-PWA0001
L1
INTERIOR LIGHT
1-LH-PWA0001
E1
ELEMENT 750W/230V
5-750-PWA0002
SI
ROCKER SWITCH
1-RS-NI
WIRING DIAGRAM
PIE WARMER MINI
MODEL CODE: PWK0007 R01
WARNING
Electric Shock Hazard.
Keep water and other liquids from entering the inside
of the equipment. Liquid inside the equipment could
cause an electrical shock
Do not spray water or cleaning products. Liquid could contact the
electrical components and cause a short circuit or an electrical shock.
Do not use equipment if power cord is damaged or has been modified
SAFETY
READ ALL INSTRUCTIONS BEFORE USE. FAILURE TO
FOLLOW THESE PRECAUTIONS COULD RESULT IN INJURY TO
YOURSELF AND OTHERS
1.
When this appliances is to be positioned in close proximity
to a wall, partitions, kitchen furniture, decorative finishes, etc.
it is recommended that they be made of non-combustible material. If not, they shall be clad with a suitable non-combustible
heat insulating material, and the closest attention be paid to fire
prevention regulations.
2. Use the appliances on an individual 15A mains outlet only.
DO NOT OVERLOAD THE CIRCUIT.
3. Ensure that the equipment and the power supply cord does not
come into contact with hot surfaces.
4. Supervision is necessary when the appliance is used in close
proximity to children.
5. If the supply cord is damaged, it must be replaced with a new
cord assembly available from the suppliers agent.
6. Use only earthed outlets matching the serial plate voltage.
7. Have equipment installed by a qualified personnel in accordance
with local codes and ordinances.
8. Use equipment in a flat level position.
9. Do not operate unattended
10. The equipment may be hot, even though the pilot light is not on.
11. Do not operate if equipment has been damaged or is malfunctioning in any way.
12. These appliances are designed to run only on alternating current
(A.C.) DO NOT CONNECT TO DIRECT CURRENT (D.C)
POSITIONING DIAGRAM
PIE WARMER MINI
MODEL: PWK0007 R01
ELECTRICAL CONNECTION INFORMATION
MODEL
DESCRIPTION
PWK0007 PIE WARMER MINI
VOLTS
(V/Hz)
POWER
(W)
230V/50Hz
750
IT IS ESSENTIAL TO MAKE SURE THAT THE INCOMING
VOLTAGE IS THE SAME AS THE RATED VOLTAGE OF
THE OF THE UNIT AS FOUND ON THE SERIAL PLATE.
THE SERIAL PLATE IS LOCATED AT THE REAR OF THE
UNIT ADJACENT TO THE INCOMING CABLE ENTRY.
585
353
390
Download PDF
Similar pages