Industrial Electric Steam Iron
Gravity lron
USER MANUAL
Iron Installation & Operation
1. Hang Water Tank① at more than
5ft above from the ironing surface
(see figure at the right side) ☞
2. Connect one end of Silicon Hose②
to Solenoid Valve③, and the other
end to Water Tank Valve
④ tap (see figure at the right side) ☞
3. Fix Power Cord⑤ and Silicon Hose②
using S Hook⑥
(see figure at the right side) ☞
4. Connect power plug to power socket,
and turn on Power Switch⑦.
5. Set Temperature Control Knob⑧ to
4 and wait 5 minutes until iron is
heated to the set temperature.
6. Turn Water Tank Valve④ to counterclockwise to open and press Steam
Switch⑨ to spray steam.
7. Always place the iron on the Silicon
Plate⑩ when you need to leave the
iron for a while during ironing.
Otherwise, there is a risk of fire.
8. Be sure to turn off power when you
do not use iron, and cool down the
iron at least 30 minutes.
①Hang Water Tank
④Water Tank
Valve
⑤Fix Power Cord
②Silicon
Hose
⑥S Hook
1.5M
③Solenoid Valve
⑦Power
Switch
⑨Steam Switch
⑧Control
Knob
⑩Silicon
Plate
Circuit Diagrams
T.F
S S/W
T.S
R
V
H
SOL.V
E.G
P S/W
2
L
V
P S/W
S S/W
E.G
SOL.V
T.F
Fuse
T.S
R
L
H
: Voltage
: Power Switch
: Steam Switch
: Earth Ground
: Solenoid Valve
: Over-Temperature
: Temperature Setting
: Resistance
: Lamp
: Heater
Gravity lron
Important Notice
Do not place iron upright direction when not in use. (See following figure)
How to operate
1. After iron temperature is sufficiently heated, open water tank valve, and
press the steam switch. (Press for 1~2 seconds and pause for 3~4 seconds.
Repeat, pressing 1~2 seconds then resting 3~4 seconds.)
Press the steam switch this way when you need steam.
2. Start ironing.
3. Do not press steam switch continuously longer than 5~6 seconds for a proper steam function.
4. Select the number of temperature control knob according to corresponding
temperature/ clothes which is following:
# 1, 2 --------- Pre-heating
# 3 ----------- Silk or sensitive clothes (low temperature)
# 4 ----------- Cottons and wool (medium temperature)
# 5 ----------- Other thick clothes (high temperature)
5. Cover ¡°Iron Shoe¡± to iron to get a better ironing effect without glossy to the clothes after ironing.
6. Please keep flammable materials away from the iron during ironing because temperature
of iron plate is very hot (over 200℃). Also, place the iron over silicon plate when not in use.
7. Always remove the power plug from socket when not in use.
of iron plate is very hot (over 200℃). Also, place iron over silicon plate when not in use.
8. Always remove power plug from socket when iron is not in use.
Self-Check Points
Problems
Iron does not work at all
Check Points
Corrective Actions
♧ Is power plug is connected to power socket?
♣ Connect power plug
♧ Is main switch turned on?
♣ Turn on main switch
♧ Is there water in water tank?
♣ Fill water to the water tank
♧ Is water tank valve opened?
♣ Turn water tank valve
Steam does not come out
counter clockwise
♧ Is silicon hose twisted or clogged?
♣ Release twist or remove
clogged materials
Steam pressure is weak
Water flows out
Steam comes out when
switch is not pressed
♧ Is water tank valve fully opened?
♣ Fully open water tank valve
♧ Is steam hole clogged?
♣ Unclog steam hole
♧ Does temperature control knob
indicate too low temperature?
♧ Is steam switch pressed too long
(more than 10 seconds)
♧ Is steam switch out of order?
♧ Is rubber packing inside solenoid
valve wore out?
♣ Adjust tempera control
knob to higher temperature
♣ Press steam switch only
1~2 second
♣ Contact head office or A/S
centers
3
Safety Regulations
Please observe following safety regulations to prevent any danger or accidents.
1. Be careful when connecting iron power cord, and check whether iron’s indicated voltage
matches with power supply socket voltage.
2. Fill water tank with clean water. Use of Silver Star's water purifier agent is recommended.
3. Be sure to disconnect the power plug from socket before filling water to water tank.
4. Be careful with steam leakage when connecting silicon hose to water tank and iron.
5. Do not connect multiple plugs to one power socket. There is risk of fire
(Fire Department recommended item).
6. Do not press steam switch continuously (more than 10 seconds). It is the cause of
flowing water instead of steam.
7. Do not press steam switch too hard. It causes the malfunction.
8. User shall always be near to the iron when in use. Iron’s power must be turned off and
its plug must be removed from socket when user needs to leave iron for a while.
9. Do not spray iron steam directly either to human body or animals. There is risk of burn injury.
10. Keep away any part of human body from iron’s bottom plate while in use.There is a risk of burn injury.
11. If the temperature control does not work and keep high temperature, stop
using it immediately and disconnect the plug, then contact authorized service center.
12. If water or other foreign materials entered into iron cover, turn off power by
disconnecting the plug and inquire authorized service center.
13. Remove iron’s power plug from socket when it’s lightning or thunders.
14. Do not let children touch or operate iron.
15. Be sure to change power cable by qualified technician from manufacturer or authorized
service center when it is damaged.
16. Never touch or modify inner parts of controller in the iron because they are sensitive
parts. There is a risk of iron malfunction or fire if incorrectly handled.
17. Do not touch power cable or operate iron with wet hand. There is risk of electric shock.
18. To clean iron, disconnect power plug from socket and clean it after iron is cooled down.
19. Remove all steam inside iron and disconnect power plug from socket when iron is not using.
20. Hold power plug when disconnect it from socket. Do not pull out the power cable to
disconnect plug. It is the cause of fire or electric shock by short circuit.
21. Stop using iron, disconnect power plug and contact authorized service center when
there is any other sign or symptoms of trouble.
22. Our company does not have liability for any accident that occurred by not observing
above safety regulations or any accident caused by mistakes or carelessness by user.
Also, our company does not have liability for any accident during or after repair
of the iron by unauthorized person or at unauthorized place.
23. Please contact our head office or authorized service center if you have any question for
product description or trouble.
Always be sure to observe above safety regulations. Manufacturer does not
have liability for any damages caused by not observing above safety regulation.
4
Gravity lron
Size and Specifications
Model
ES-94A
ES-300
ES-85AF
ES-90A
ES-97A
EZ5
EZ90
EZ300
ES-94AL
ES-300L
EZ5L
Voltage
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
120V/220V~
Wattage
1000W
1000W
1000W
1000W
1000W
1000W
1200W
1200W
1300W
1300W
1300W
Weight
2.1kg
2.1kg
2.3kg
2.1kg
1.96kg
1.9kg
2.0kg
2.1kg
2.64kg
2.64kg
2.64kg
Base size
209×120
209×120
205×124
200×112
208×108
209×120
209×120
209×120
227×138
227×138
227×138
Usage
Intermediate process
Intermediate process
Intermediate process
Intermediate process
Intermediate process
Intermediate process
Intermediate process
Intermediate process
Final process
Final process
Final process
Option Items
부품 리스트
Water Purifier
◆ It dilutes contamination by polluted
water, and helps to supply only
clean water into iron
◆ It extends lifespan of iron, and has
better effect when it is used for calcific water
◆ May be used for approximately 3~6
months, although life varies according
to water conditions. Please replace
with new water purifier after use.
Iron Shoe
◆ Use the iron shoe to prevent steam
trace iron shine on the fabric to protect
garments.
◎ Silicon pad that maintains steam pressure
◎ Durable quality for long time use
◎ More than twice the lifespan of other
products thanks to dual fastening
and rivet joints
13
Accessory parts usage and instruction to use
① Steam hole pin
Usage
Steam hole at the bottom of iron
may be clogged after long time use due
to foreign material inside the iron.
When it happens, use steam hole pin to
clear the clogged hole.
Instruction
It is able to solve the clogged steam
problem by clearing the clogged steam
hole using steam hole pin as shown in
the figure at the right side.
Caution
Iron’s bottom may be very hot. Be careful
not to touch iron’s bottom while cleaning.
② Steam switching rubber
③ Valve spring
Usage
Steam may continuously come out from
steam hole at the iron bottom when the
iron has been in use for long time. This can
be caused by hardened or aged steam
switching rubber in the solenoid valve set,
or due to corrosion or malfunction of valve
spring. Please replace the part with attached
spare part when it happens.
Usage
As shown in the figure at the right side,
open the solenoid valve in the iron using spanner and replace steam switching rubber
or valve spring, and reassemble it to solve this problem.
Caution
Be sure to assemble according to the sequence in the figure after replacing steam
switching rubber or valve spring. It may not work properly if the assemble sequence
is nor followed.
14
HEAD OFFICE & FACTORY
EUNSUNG ELECTRIC CO.,LTD
104-5,SHINPYUNG-RI,SHINBUK-MYON, POCHUN-SI, KYUNGGIDO,KOREA
TEL: 82-31-531-8131~6 FAX : 82-31-531-8130
E-MAIL: silverstar@silverstar.co.kr
JIAXING EUNSUNG ELECTRIC CO.,LTD.
MU YANG ROAD 349# ECONOMIC DEVELOPMENT ZONE
JIAXING ZHEJIANG CHINA
TEL: 86-573-8222-4373 FAX: 86-573-8222-4391
E-MAIL:silverstar@silverstar.co.kr
www.silverstar.co.kr
Download PDF
Similar pages