P Office 7.0 Installation Instruction

IP Office 7.0
IP Office Standard Version Installation
15-601042 Issue 23e - (16 March 2011)
© 2011 AVAYA All Rights Reserved.
Notices
While reasonable efforts have been made to ensure that the information in
this document is complete and accurate at the time of printing, Avaya
assumes no liability for any errors. Avaya reserves the right to make changes
and corrections to the information in this document without the obligation to
notify any person or organization of such changes.
Documentation disclaimer
Avaya shall not be responsible for any modifications, additions, or deletions
to the original published version of this documentation unless such
modifications, additions, or deletions were performed by Avaya.
End User agree to indemnify and hold harmless Avaya, Avaya's agents,
servants and employees against all claims, lawsuits, demands and judgments
arising out of, or in connection with, subsequent modifications, additions or
deletions to this documentation, to the extent made by End User.
Link disclaimer
Avaya is not responsible for the contents or reliability of any linked Web sites
referenced within this site or documentation(s) provided by Avaya. Avaya is
not responsible for the accuracy of any information, statement or content
provided on these sites and does not necessarily endorse the products,
services, or information described or offered within them. Avaya does not
guarantee that these links will work all the time and has no control over the
availability of the linked pages.
Warranty
Avaya provides a limited warranty on this product. Refer to your sales
agreement to establish the terms of the limited warranty. In addition, Avaya’s
standard warranty language, as well as information regarding support for this
product, while under warranty, is available to Avaya customers and other
parties through the Avaya Support Web site: http://www.avaya.com/support.
Please note that if you acquired the product from an authorized Avaya reseller
outside of the United States and Canada, the warranty is provided to you by
said Avaya reseller and not by Avaya.
Licenses
THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE,
HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/ ARE APPLICABLE TO ANYONE
WHO DOWNLOADS, USES AND/OR INSTALLS AVAYA SOFTWARE,
PURCHASED FROM AVAYA INC., ANY AVAYA AFFILIATE, OR AN AUTHORIZED
AVAYA RESELLER (AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT
WITH AVAYA OR AN AUTHORIZED AVAYA RESELLER. UNLESS OTHERWISE
AGREED TO BY AVAYA IN WRITING, AVAYA DOES NOT EXTEND THIS
LICENSE IF THE SOFTWARE WAS OBTAINED FROM ANYONE OTHER THAN
AVAYA, AN AVAYA AFFILIATE OR AN AVAYA AUTHORIZED RESELLER, AND
AVAYA RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU AND
ANYONE ELSE USING OR SELLING THE SOFTWARE WITHOUT A LICENSE. BY
INSTALLING, DOWNLOADING OR USING THE SOFTWARE, OR AUTHORIZING
OTHERS TO DO SO, YOU, ON BEHALF OF YOURSELF AND THE ENTITY FOR
WHOM YOU ARE INSTALLING, DOWNLOADING OR USING THE SOFTWARE
(HEREINAFTER REFERRED TO INTERCHANGEABLY AS “YOU” AND “END
USER”), AGREE TO THESE TERMS AND CONDITIONS AND CREATE A
BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE APPLICABLE
AVAYA AFFILIATE (“AVAYA”).
Avaya grants End User a license within the scope of the license types
described below. The applicable number of licenses and units of capacity for
which the license is granted will be one (1), unless a different number of
licenses or units of capacity is specified in the Documentation or other
materials available to End User. "Designated Processor" means a single
stand-alone computing device. "Server" means a Designated Processor that
hosts a software application to be accessed by multiple users. "Software"
means the computer programs in object code, originally licensed by Avaya
and ultimately utilized by End User, whether as stand-alone products or
pre-installed on Hardware. "Hardware" means the standard hardware
originally sold by Avaya and ultimately utilized by End User.
IP Office Standard Version Installation
IP Office 7.0
License types
Designated System(s) License (DS). End User may install and use each copy
of the Software on only one Designated Processor, unless a different number
of Designated Processors is indicated in the Documentation or other materials
available to End User. Avaya may require the Designated Processor(s) to be
identified by type, serial number, feature key, location or other specific
designation, or to be provided by End User to Avaya through electronic means
established by Avaya specifically for this purpose.
Copyright
Except where expressly stated otherwise, no use should be made of materials
on this site, the Documentation(s) and Product(s) provided by Avaya. All
content on this site, the documentation(s) and the product(s) provided by
Avaya including the selection, arrangement and design of the content is
owned either by Avaya or its licensors and is protected by copyright and other
intellectual property laws including the sui generis rights relating to the
protection of databases. You may not modify, copy, reproduce, republish,
upload, post, transmit or distribute in any way any content, in whole or in
part, including any code and software. Unauthorized reproduction,
transmission, dissemination, storage, and or use without the express written
consent of Avaya can be a criminal, as well as a civil, offense under the
applicable law.
Third Party Components
Certain software programs or portions thereof included in the Product may
contain software distributed under third party agreements ("Third Party
Components"), which may contain terms that expand or limit rights to use
certain portions of the Product ("Third Party Terms"). Information regarding
distributed Linux OS source code (for those Products that have distributed the
Linux OS source code), and identifying the copyright holders of the Third
Party Components and the Third Party Terms that apply to them is available
on the Avaya Support Web site: http://support.avaya.com/Copyright.
Preventing toll fraud
"Toll fraud" is the unauthorized use of your telecommunications system by an
unauthorized party (for example, a person who is not a corporate employee,
agent, subcontractor, or is not working on your company's behalf). Be aware
that there can be a risk of toll fraud associated with your system and that, if
toll fraud occurs, it can result in substantial additional charges for your
telecommunications services.
Avaya fraud intervention
If you suspect that you are being victimized by toll fraud and you need
technical assistance or support, call Technical Service Center Toll Fraud
Intervention Hotline at +1-800-643-2353 for the United States and Canada.
For additional support telephone numbers, see the Avaya Support Web site:
http://support.avaya.com
Suspected security vulnerabilities with Avaya products should be reported to
Avaya by sending mail to: securityalerts@avaya.com.
Trademarks
Avaya and Aura are trademarks of Avaya, Inc.
The trademarks, logos and service marks (“Marks”) displayed in this site, the
documentation(s) and product(s) provided by Avaya are the registered or
unregistered Marks of Avaya, its affiliates, or other third parties. Users are
not permitted to use such Marks without prior written consent from Avaya or
such third party which may own the Mark. Nothing contained in this site, the
documentation(s) and product(s) should be construed as granting, by
implication, estoppel, or otherwise, any license or right in and to the Marks
without the express written permission of Avaya or the applicable third party.
Avaya is a registered trademark of Avaya Inc. All non-Avaya trademarks are
the property of their respective owners.
Downloading documents
For the most current versions of documentation, see the Avaya Support Web
site: http://www.avaya.com/support
Contact Avaya Support
Avaya provides a telephone number for you to use to report problems or to
ask questions about your product. The support telephone number is
1-800-242-2121 in the United States. For additional support telephone
numbers, see the Avaya Web site: http://www.avaya.com/support
Page 2
15-601042 Issue 23e (16 March 2011)
Contents
Contents
1. System Overview
1.1 IP Office Modes
.....................................................................
............................................................................
1.1.1 Hardware
Support Summary
1.1.2 Feature
Support Summary
............................................................................
1.2 Control Units
.....................................................................
1.3 IP500v2 System
.....................................................................
Components
.....................................................................
1.4 IP500 Office
System Components
1.5 Control Unit.....................................................................
Cards
1.5.1 IP500
............................................................................
Base Cards
1.5.2 IP500
............................................................................
Trunk Cards
............................................................................
1.5.3 IP400
Trunk Cards
1.5.4 Other
Cards
............................................................................
1.6 External Expansion
.....................................................................
Modules
1.6.1 IP500
............................................................................
External Expansion Modules
............................................................................
1.6.2 IP400
External Expansion Modules
1.7 Power Supplies
and Cables
.....................................................................
1.7.1 Power
............................................................................
Supplies
1.7.2 Power
............................................................................
Supply Cords
............................................................................
1.7.3 Power
Supply Backup
1.7.4 Cabling
and Cables
............................................................................
............................................................................
1.7.5 Grounding
1.7.6 Lightning Protection/Out-of-Building
Connections
............................................................................
1.8 Wall and Rack
.....................................................................
Mounting
1.9 Feature Keys
and Licenses
.....................................................................
1.10 IP Office Phones
.....................................................................
1.11 VoIP
.....................................................................
1.11.1............................................................................
Voice Compression Channels
1.12 Supported.....................................................................
Country Locales
1.13 IP Office Software
Applications
.....................................................................
1.14 Training .....................................................................
1.15 Web Sites.....................................................................
1.16 Emergency
and Power Failure Ports
.....................................................................
11
12
13
14
15
17
19
19
22
24
25
26
29
31
33
33
34
35
36
38
39
40
42
43
45
46
47
48
51
51
52
2. Installation Requirements
2.1 Environmental
.....................................................................
Requirements
2.2 Space Requirements
.....................................................................
2.2.1 IP500
............................................................................
and IP500v2 Control Units
2.2.2 External
............................................................................
Expansion Modules
2.2.3 Wall
............................................................................
Mounting
2.2.4 Rack
............................................................................
Space Requirements
54
55
56
56
57
59
3. IP Office Administration Software
3.1 Installing the
.....................................................................
Admin Applications
3.2 Installer PC.....................................................................
Connection
3.3 Starting Manager
.....................................................................
3.4 Starting System
.....................................................................
Status
3.5 Starting Monitor
.....................................................................
3.6 Phone Based
.....................................................................
Administration
63
65
66
67
68
68
4. IP500v2 Installation
4.1 Tools and Equipment
.....................................................................
Required
4.2 Documentation
.....................................................................
4.3 Unpacking .....................................................................
4.4 SD Card Preparation
.....................................................................
4.4.1 Upgrade
............................................................................
the Card Firmware
IP Office Standard Version Installation
IP Office 7.0
71
72
73
74
74
............................................................................
4.4.2 Adding
a Pre-Built Configuration File
4.4.3 Creating
............................................................................
a Configuration File
4.4.4 Adding
............................................................................
a License File
............................................................................
4.4.5 Adding
a 9600 Series Screen Saver File
4.4.6 Adding
Music on Hold Files
............................................................................
4.5 IP500 Card.....................................................................
Installation
4.5.1 IP500
............................................................................
Daughter Card Preparation
............................................................................
4.5.2 IP500
Legacy Card Preparation
4.5.3 IP500
Card Insertion
............................................................................
4.6 Wall Mounting
.....................................................................
4.6.1 Wall
............................................................................
Mounting Kit V2
............................................................................
4.6.2 Wall
Mounting Kit V1
4.7 Rack Mounting
.....................................................................
4.8 Connecting.....................................................................
External Expansion Modules
4.9 Grounding .....................................................................
.....................................................................
4.10 Network Connection
4.11 Starting the
System
.....................................................................
4.11.1............................................................................
Checking the LEDs
4.12 Changing.....................................................................
the System to Standard Mode
.....................................................................
4.13 Connecting
Phones
74
76
77
77
77
78
79
80
81
82
83
85
86
88
90
91
92
93
95
96
5. Initial Configuration
5.1 Setting the.....................................................................
System Locale
5.2 Changing.....................................................................
the IP Address Settings
5.3 Changing.....................................................................
the Default Passwords
5.4 Extension.....................................................................
Numbering
5.5 Entering Licenses
.....................................................................
5.6 Disable Unused
Trunks
.....................................................................
.....................................................................
5.7 Setting the
Digital Trunk Clock Source
5.8 Setting the
Trunk Prefixes
.....................................................................
101
102
103
105
107
108
110
112
6. Additional Processes
6.1 Switching.....................................................................
Off an IP Office System
6.2 Rebooting.....................................................................
an IP Office System
6.3 Memory Card
Removal
.....................................................................
6.4 Changing.....................................................................
Components
6.5 Swapping.....................................................................
Extension Users
6.6 Upgrading.....................................................................
the IP Office Software
6.6.1............................................................................
Using the Upgrade Wizard
6.6.2............................................................................
Using an SD Card
6.6.3............................................................................
Upgrading 2400/5400 Phones
6.7 Out of Building
.....................................................................
Telephone Installations
6.7.1............................................................................
DS Phones
6.7.2............................................................................
Analog Phone Barrier Box
6.7.3............................................................................
Rack Mounting Barrier Boxes
6.8 Using the .....................................................................
External Output Port
6.8.1............................................................................
Port Connection
6.9 So8 BRI Module
.....................................................................
6.9.1............................................................................
Example 1: ISDN Terminal
6.9.2............................................................................
Example 2: Video Conference
6.10 SNMP .....................................................................
6.10.1
Installing the IP Office MIB Files
............................................................................
6.10.2
............................................................................
Enabling SNMP and Polling Support
6.10.3
............................................................................
Enabling SNMP Trap Sending
6.11 Reset Button
.....................................................................
6.12 AUX Button
.....................................................................
6.13 DTE Port.....................................................................
Maintenance
6.13.1
............................................................................
DTE Port Settings
6.13.2
............................................................................
Erasing the Configuration
117
119
120
122
124
125
126
128
129
131
132
133
134
135
135
136
136
137
139
140
142
142
143
143
144
144
145
Page 3
15-601042 Issue 23e (16 March 2011)
6.13.3
............................................................................
Defaulting Security Settings
147
6.13.4
............................................................................
Erasing the Operational Firmware
148
7. SD Card Management
7.1 Booting from
.....................................................................
the SD Cards
7.2 Creating an
.....................................................................
IP Office SD Card
.....................................................................
7.3 Viewing the
Card Contents
7.4 Backing Up
the System SD Card
.....................................................................
7.4.1............................................................................
Backing Up the Primary Folder
7.4.2............................................................................
Restore from the Backup Folder
7.4.3............................................................................
Backing Up to the Optional Card
7.4.4............................................................................
Restoring from the Optional Card
7.5 Upgrading.....................................................................
Card Software
7.5.1............................................................................
Upgrading Remotely Using Manager
7.5.2............................................................................
Upgrading the SD Card Locally
7.5.3............................................................................
Upgrading Using an Optional SD Card
7.6 Removing.....................................................................
SD Cards
7.6.1............................................................................
Card Shutdown
7.6.2............................................................................
Card Startup
7.6.3............................................................................
System Shutdown
155
157
158
159
159
160
161
162
164
165
165
166
167
167
168
169
8. IP500 Basic Installation
8.1 IP500 Tools
.....................................................................
Required
8.2 IP500 Read
.....................................................................
the Documentation
8.3 IP500 Unpacking
.....................................................................
8.4 IP500 Card
.....................................................................
Installation
8.4.1............................................................................
IP500 Daughter Card Preparation
8.4.2............................................................................
IP500 Legacy Card Preparation
8.4.3............................................................................
IP500 Card Insertion
8.5 Inserting the
.....................................................................
Feature Key
8.6 Applying Power
.....................................................................
8.7 Check the.....................................................................
CPU LED
8.8 Upgrading.....................................................................
the Core Software
8.9 Receiving.....................................................................
the Configuration
8.10 Adding Licences
.....................................................................
.....................................................................
8.11 Adding External
Expansion Modules
8.12 Rack Mounting
.....................................................................
8.13 Wall Mounting
.....................................................................
8.13.1
Wall Mounting Kit V2
............................................................................
............................................................................
8.13.2
Wall Mounting Kit V1
8.14 Grounding
.....................................................................
172
173
174
175
176
177
178
179
180
182
183
184
185
186
188
190
191
193
194
9. System Components
.....................................................................
9.1 IP500v2 Control
Unit
9.2 IP500 Control
.....................................................................
Unit
9.3 IP500 Base
.....................................................................
Cards
9.3.1............................................................................
4-Port Expansion Card
9.3.2............................................................................
Analog Phone
9.3.3............................................................................
ATM Combination Card
9.3.4............................................................................
BRI Combination Card
9.3.5............................................................................
Digital Station
9.3.6............................................................................
ETR6 Card
9.3.7............................................................................
Legacy Card Carrier
9.3.8............................................................................
TCM8 Digital Station
9.3.9............................................................................
VCM
9.4 IP500 Trunk
.....................................................................
Daughter Cards
9.4.1............................................................................
Analog Trunk Card
9.4.2............................................................................
BRI Trunk Cards
9.4.3............................................................................
PRI Trunk Cards
IP Office Standard Version Installation
IP Office 7.0
199
202
205
208
209
210
211
212
213
214
215
216
218
220
221
222
.....................................................................
9.5 IP500 Expansion
Modules
9.5.1............................................................................
Analog Trunk 16
9.5.2............................................................................
BRI SO8
9.5.3............................................................................
Digital Station
9.5.4............................................................................
Digital Station A
9.5.5............................................................................
Phone
9.6 Feature Keys
.....................................................................
9.6.1............................................................................
IP500v2 System SD Cards
9.6.2............................................................................
IP500 Smart Card
9.7 IP400 Trunk
.....................................................................
Cards
9.7.1............................................................................
Analog Trunk Card Uni (ATM4U)
9.7.2............................................................................
Analog Trunk Cards (ATM4)
9.7.3............................................................................
BRI Trunk Cards
9.7.4............................................................................
T1 PRI Trunk Cards
9.7.5............................................................................
E1 PRI Trunk Cards
9.7.6............................................................................
E1R2 PRI Trunk Cards
9.8 IP400 Internal
Cards
.....................................................................
9.8.1............................................................................
Embedded Voicemail Memory Cards
9.8.2............................................................................
Voice Compression Modules
.....................................................................
9.9 IP400 Expansion
Modules
9.9.1............................................................................
Analog Trunk 16
9.9.2............................................................................
Digital Station V2
9.9.3............................................................................
Digital Station
9.9.4............................................................................
Phone V2
9.9.5............................................................................
Phone
9.9.6............................................................................
So8
9.10 Mounting.....................................................................
Kits
9.10.1
............................................................................
IP500 Wall Mounting Kits
9.10.2
IP500 Rack Mounting Kit
............................................................................
............................................................................
9.10.3
IP400 Rack Mounting Kit
9.10.4
Barrier Box Rack Mounting Kit
............................................................................
9.11 Phones .....................................................................
9.11.1
1010/1040
............................................................................
............................................................................
9.11.2
1120/1140/1220/1230
9.11.3
1403
............................................................................
9.11.4
............................................................................
1408
9.11.5
1416
............................................................................
............................................................................
9.11.6
1603
9.11.7
1608
............................................................................
9.11.8
............................................................................
1616
9.11.9
2402
............................................................................
............................................................................
9.11.10
2410
9.11.11
............................................................................
2420
9.11.12
............................................................................
3616
9.11.13
............................................................................
3620
9.11.14
3626
............................................................................
9.11.15
............................................................................
3641
9.11.16
............................................................................
3645
9.11.17
............................................................................
3701
9.11.18
3711
............................................................................
9.11.19
............................................................................
3720
9.11.20
............................................................................
3725
9.11.21
............................................................................
3740
9.11.22
............................................................................
3749
9.11.23
............................................................................
3810
9.11.24
............................................................................
3910
9.11.25
............................................................................
3920
9.11.26
............................................................................
4406
223
225
227
229
231
234
236
236
238
239
240
241
241
242
242
243
244
244
245
246
248
250
252
254
256
258
260
260
261
261
261
262
264
265
266
267
268
269
271
273
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
290
291
Page 4
15-601042 Issue 23e (16 March 2011)
Contents
9.11.27
............................................................................
4412
9.11.28
............................................................................
4424
9.11.29
............................................................................
4601
............................................................................
9.11.30
4602
9.11.31
4610
............................................................................
9.11.32
............................................................................
4620
9.11.33
............................................................................
4621
............................................................................
9.11.34
4625
9.11.35
5402
............................................................................
9.11.36
............................................................................
5410
9.11.37
............................................................................
5420
............................................................................
9.11.38
5601
9.11.39
5602
............................................................................
9.11.40
............................................................................
5610
9.11.41
............................................................................
5620
............................................................................
9.11.42
5621
9.11.43
9404
............................................................................
9.11.44
............................................................................
9408
9.11.45
............................................................................
9504
............................................................................
9.11.46
9508
9.11.47
9608
............................................................................
9.11.48
............................................................................
9620L, 9620C
9.11.49
9621G
............................................................................
9.11.50
............................................................................
9630G
9.11.51
9640, 9640G
............................................................................
............................................................................
9.11.52
9641G
9.11.53
9650, 9650C
............................................................................
9.11.54
............................................................................
Audio Conferencing Unit
9.11.55
ETR 6, ETR 6D
............................................................................
............................................................................
9.11.56
ETR 18, ETR 18D
9.11.57
ETR 34D
............................................................................
9.11.58
............................................................................
M7100
9.11.59
M7100N
............................................................................
............................................................................
9.11.60
M7208
9.11.61
M7208N
............................................................................
9.11.62
............................................................................
M7310
9.11.63
M7310N
............................................................................
............................................................................
9.11.64
M7324
9.11.65
M7324N
............................................................................
9.11.66
............................................................................
T7000
9.11.67
T7100
............................................................................
............................................................................
9.11.68
T7208
9.11.69
............................................................................
T7316
9.11.70
............................................................................
T7316E
9.11.71
............................................................................
T7406, T7406e
9.11.72
T3 Classic
............................................................................
9.11.73
............................................................................
T3 Comfort
9.11.74
............................................................................
T3 Compact
9.12 Phone Add-Ons
.....................................................................
9.12.1
201B RIM
............................................................................
9.12.2
............................................................................
4450
9.12.3
............................................................................
BM32
9.12.4
............................................................................
DBM32
9.12.5
............................................................................
EU24
9.12.6
............................................................................
EU24BL
9.12.7
............................................................................
KLM Module
9.12.8
............................................................................
SMB24
9.12.9
............................................................................
T3 DSS
IP Office Standard Version Installation
IP Office 7.0
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
308
309
309
310
311
313
314
316
318
319
321
322
323
324
325
325
326
326
327
327
328
328
329
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
............................................................................
9.12.10
T7316e KEM
9.12.11
............................................................................
XM24
9.13 Ancilliary.....................................................................
Systems
............................................................................
9.13.1
Digitial Mobility Solution
9.13.2
DECT R4
............................................................................
9.14 Applications
.....................................................................
9.14.1
............................................................................
IP Office Application Server
............................................................................
9.14.2
ContactStore
9.14.3
Customer Call Reporter (CCR)
............................................................................
9.14.4
............................................................................
Manager
9.14.5
............................................................................
Monitor
............................................................................
9.14.6
one-X Portal for IP Office
9.14.7
Phone Manager
............................................................................
9.14.8
............................................................................
SoftConsole
9.14.9
............................................................................
System Status Application (SSA)
............................................................................
9.14.10
TAPI
9.14.11
Voicemail Pro
............................................................................
9.14.12
............................................................................
Single Server Support
9.14.13
............................................................................
IP Office Ports
.....................................................................
9.15 Operating
System Summary
9.16 Physical.....................................................................
Ports
9.16.1
............................................................................
Cables
9.16.2
ANALOG Port
............................................................................
9.16.3
............................................................................
AUDIO Port
9.16.4
BRI Port (So)
............................................................................
............................................................................
9.16.5
BRI Port (To)
9.16.6
DC I/P Port
............................................................................
9.16.7
............................................................................
DS Ports
9.16.8
EF Port
............................................................................
............................................................................
9.16.9
RS232 DTE Port
9.16.10
ETR Port
............................................................................
9.16.11
............................................................................
EXPANSION Port
9.16.12
EXT O/P Port
............................................................................
............................................................................
9.16.13
LAN Port
9.16.14
PF Port
............................................................................
9.16.15
............................................................................
PHONE (POT) Port
9.16.16
PRI Port
............................................................................
............................................................................
9.16.17
TCM Port (RJ21)
9.16.18
TCM Port (RJ45)
............................................................................
9.17 Licences.....................................................................
9.17.1
System Edition Licenses
............................................................................
............................................................................
9.17.2
Trunk Licensing
9.17.3
............................................................................
Telephone/Endpoint Licenses
9.17.4
............................................................................
User Licenses
9.17.5
............................................................................
Voicemail Pro Licenses
9.17.6
Customer Call Reporter Licenses
............................................................................
9.17.7
............................................................................
Trial Licenses
9.17.8
............................................................................
Other Licenses
347
348
349
349
350
351
351
353
354
355
356
357
358
360
361
362
363
365
366
369
370
371
373
373
374
375
376
376
377
377
378
379
379
380
381
382
383
384
385
386
387
388
388
390
392
394
396
397
10. Safety Statements
10.1 Lithium Batteries
.....................................................................
10.2 Lightning.....................................................................
Protection/Hazard Symbols
10.3 Trunk Interface
Modules
.....................................................................
10.4 Further Information
.....................................................................
and Product Updates
10.5 Port Safety
.....................................................................
Classification
10.6 EMC Directive
.....................................................................
10.7 Regulatory
.....................................................................
Instructions for Use
10.7.1
............................................................................
Australia
400
400
401
402
402
403
404
404
Page 5
15-601042 Issue 23e (16 March 2011)
10.7.2
............................................................................
Canada
404
10.7.3
............................................................................
China
405
10.7.4
............................................................................
European Union
406
............................................................................
406
10.7.5
New Zealand
10.7.6
FCC Notification
............................................................................
407
10.7.7
............................................................................
Compliance with FCC Rules
409
Index ...............................................................................411
IP Office Standard Version Installation
IP Office 7.0
Page 6
15-601042 Issue 23e (16 March 2011)
Chapter 1.
System Overview
IP Office Standard Version Installation
IP Office 7.0
Page 7
15-601042 Issue 23e (16 March 2011)
System Overview:
1. System Overview
This documentation is intended to assist with the installation of the core components of an Avaya IP Office Standard
Version mode telephone system. It describes those components and factors that should be considered for an installation.
· The IP Office is a converged voice and data communications system. It should therefore only be installed by
persons with telephony and IP data network experience.
· Installers must be trained on IP Office systems. Through its Avaya University 51 (AU), Avaya provides a range of
training courses including specific IP Office implementation and installation training. It also provides certification
schemes for installers to achieve various levels of IP Office accreditation.
· It is the installer’s responsibility to ensure that all installation work is done in accordance with local and national
regulations and requirements. It is also their responsibility to accurately establish the customer’s requirements
before installation and to ensure that the installation meets those requirements.
· You should read and understand this documentation before installation. You should also obtain and read the Avaya
Technical Bulletins relevant to recent IP Office software and hardware releases to ensure that you are familiar with
any changes to the IP Office equipment and software.
IP Office Standard Version Installation
IP Office 7.0
Page 9
15-601042 Issue 23e (16 March 2011)
Additional Documentation
The following components of IP Office are outside the range of a basic IP Office installation. They are covered by separate
installation and configuration documentation. If those components are to be part of the IP Office system installation, that
documentation should be obtained, read and understood prior to the installation.
· Partner Version Installation
· Compact DECT Installation.
· one-X Portal for IP Office Installation
· IP DECT R4 Installation.
· 4600/5600 Series IP Phone Installation.
· 3600 Series Wireless IP Installation.
· Embedded Voicemail Installation.
· Phone Manager Installation Manual.
· Voicemail Pro Installation.
· SoftConsole Installation Manual.
· Contact Store Installation.
· SIP Extension Configuration
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
Equipment Availability
SAP codes and details of specific items within this documentation are for reference only. Items available in any specific
locale should be confirmed against the local Avaya IP Office price list for that locale. The local price list may also include
additional items relative to the installation requirements of that locale.
This documentation covers the equipment supported by IP Office Release 6. That includes equipment supported but no
longer available as new from Avaya.
Repair
IP Office systems do not contain any user serviceable or repairable components. If a faulty unit is suspected the whole
unit should be replace.
· IP400 control units should only be opened where indicated for the installation of IP400 cards.
· IP500 control units should not be opened under any circumstances.
RoHS
RoHS is a European Union directive for the Removal of Certain Hazardous Substances from Electrical and Electronic
Equipment. Similar legislation has been or is being introduced in a number of other countries. Avaya has decided to make
its global product range compliant with the requirements of RoHS.
The actions taken vary
· In some cases equipment has been discontinued and is no longer available from Avaya.
· In some cases new manufactured stock has been made RoHS compliant and keeps its existing SAP code.
· In other cases the equipment has been replaced by a new RoHS compliant alternative with new SAP codes.
· The SAP codes within this document are for RoHS compliant equipment unless otherwise stated.
IP Office Standard Version Installation
IP Office 7.0
Page 10
15-601042 Issue 23e (16 March 2011)
System Overview:
1.1 IP Office Modes
IP Office systems based on the IP500v2 control unit can run in a number of modes:
· IP Office Standard Version
· IP Office Essential Edition - Quick Version
· IP Office Essential Edition - Norstar Version
· IP Office Essential Edition - PARTNER® Version
· Avaya Branch Gateway
This is a special mode used for B5800 control units and is not covered by this documentation. Refer to the separate
Avaya Branch Gateway documentation.
IP500 control units only run in IP Office Standard Version mode. The default mode used for IP500v2 systems is
determined by the System SD card present when the system is first installed.
· IP Office U-Law
A system fitted with this type of card will default to U-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode Key System operation. Intended for North American locales.
· IP Office A-Law
A system fitted with this type of card will default to A-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode PBX System operation. Intended for locales outside North
America.
· IP Office Partner Version
A system fitted with this type of card will default to U-Law telephony and IP Office Essential Edition PARTNER® Version mode Key System operation. Supported only in North American locales.
· IP Office Norstar Version
A system fitted with this type of card will default to A-Law telephony and IP Office Essential Edition - Norstar
Version mode Key System operation. Supported only in Middle East and North African locales.
Overall Capacity
IP Office
Essential
Edition PARTNER®
Version
Extensions
Maximum Extensions
Trunks
Maximum Trunks
100
- Maximum Analog Trunks
[1]
IP Office
Essential
Edition Norstar
Version
100
[1]
IP Office
Essential
Edition Quick Version
100
[1]
IP Office
Standard
Version
384
64
64
64
[5]
208
32
32
32
- Maximum BRI Channels
[3]
–
12
12
32
- Maximum PRI Channels
[4]
24
30
30
120
- Maximum SIP Channels
[2]
20
20
20
[5]
–
–
–
[5]
- Maximum H323 IP Channels
1. 100 Extension in 3-digit extension numbering mode only. 48 extensions in 2-digit extension numbering mode.
· In non-IP Office Standard Version mode the system assumes that the base control unit is always fully
populated with up to 32 extensions, either real or phantom or a mix, to which it assigns extension numbers in
sequence. It does this before assigning extension numbers to any real extensions on attached external
expansion modules up to the system extension limit. If the system extension limit has not been exceeded, any
remaining extension numbers are assigned to additional phantom extensions.
2. Non-IP Office Standard Version mode systems support 3 SIP channels without licenses. Additional channels up to
the limit require licenses. IP Office Standard Version mode systems require licenses for all channels. In all modes,
voice compression hardware resources are also required for SIP support.
3. Non-IP Office Standard Version mode systems do not support both BRI and PRI trunks in the same system.IP Office
Standard Version mode systems support both BRI and PRI trunks in the same system.
4. Non-IP Office Standard Version mode systems are restricted to 12 BRI channels regardless of the BRI hardware
installed.
5. Capacity is dependent on licenses, voice compression resources and available bandwidth.
IP Office Standard Version Installation
IP Office 7.0
Page 11
15-601042 Issue 23e (16 March 2011)
1.1.1 Hardware Support Summary
Note that even where indicated as supported, the availability and support of equipment may still be subject to local
restrictions.
Control Unit
IP Office
Essential
Edition Norstar
Version
IP Office
Essential
Edition Quick Version
–
–
–
IP Office
Standard
Version
IP500v2 Control Unit
IP500 Control Unit
IP500 Base
Cards
IP Office
Essential
Edition PARTNER®
Version
IP500 Digital Station Card
3
3
3
3
IP500 Analog Phone 2/8 Cards
4
4
4
4
4
4
4
4
IP500 TCM8 Card
[1]
IP500 VCM 32/64 Base Cards
–
–
–
IP500 Legacy Card Carrier
–
–
–
IP500 4-Port Expansion Card
–
–
–
IP500 BRI Combination Card
[1]
–
IP500 ATM Combination Card
2
2
1
2
2
2
2
2
[1]
IP500 ETR6 Card
[1]
IP500 Trunk
Analog Trunk Card
Daughter Cards
BRI Trunk Cards[5]
3
3
–
–
PRI Trunk Card[6]
External
Expansion
Modules
–
1
[3]
Number of Modules
1
1
8
8
8
–
–
–
4
12
Digital Station 16/30
Digital Station 16A/30A
Phone 8/16/30
Analog Trunk 16
BRI So8
Telephone
Types
ETR Phones (ETR ports)
–
–
BST Phones (TCM ports)
DS Phones (DS ports)
H323 IP Phones (LAN)
–
–
–
SIP IP Phones (LAN)
–
–
–
–
–
–
DECT R4 (LAN)
DECT DMS (TCM ports)
Voicemail
Embedded Voicemail
Voicemail Pro
1. Not supported by IP500 control units. Support by IP500v2 Control units only.
2. Only 2 combinations cards are supported in a control unit, regardless of type.
3. External expansion modules can be added so long as the overall limit for extensions and trunks is not exceeded. On
non-IP Office Standard Version mode systems, only a maximum of one Analog Trunk 16 module is supported.
4. A mix of BRI and PRI trunks is not supported by IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version.
5. IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version only support a single-port PRI card.
IP Office Standard Version Installation
IP Office 7.0
Page 12
15-601042 Issue 23e (16 March 2011)
System Overview: IP Office Modes
1.1.2 Feature Support Summary
IP Office
Essential
Edition PARTNER®
Version
Administration
IP Office
Essential
Edition Norstar
Version
IP Office
Essential
Edition Quick Version
Phone Based Administration
–
Manager - Simplified View
IP Office
Applications
IP Office
Standard
Version
–
Manager - Advanced View
–
–
–
Customer Call Reporter
–
–
–
one-X Portal for IP Office
–
–
–
Phone Manager
–
–
–
SoftConsole
–
–
–
–
–
–
–
–
–
IP Office Manager
Monitor (System Monitor)
System Status Application
TAPI (1st Party)
TAPI (3rd Party)
Voicemail Pro
Locales
Voicemail
Languages
Canada,
Bahrain, Egypt, Argentina, Australia, Bahrain,
Mexico, United
Kuwait,
Belgium, Brazil, Canada, Chile,
States
Morocco,
China, Colombia, Denmark,
Oman,
Egypt, Finland, France,
Pakistan,
Germany, Greece, Hong Kong,
Qatar, Saudi
Hungary, Iceland, India, Italy,
Arabia, South Korea, Kuwait, Mexico, Morocco,
Africa, Turkey,
Netherlands, New Zealand,
United Arab
Norway, Oman, Pakistan, Peru,
Emirates
Poland, Portugal, Qatar, Russia,
Saudi Arabia, Singapore, South
Africa, Spain, Sweden,
Switzerland, Taiwan, Turkey,
United Arab Emirates, United
Kingdom, United States,
Venezuela.
Embedded Voicemail
Arabic, Chinese-Mandarin, Chinese-Cantonese, Danish, Dutch,
English-UK, English-US, Finnish, French, French-Canadian,
German, Italian, Korean, Norwegian, Portuguese, Portuguese
Brazilian, Russian, Swedish, Spanish, Spanish-Latin, SpanishArgentinean.
Voicemail Pro
–
–
–
As above plus:
Hungarian,
Greek, Polish.
Minus: Arabic.
User Name
Administrator
Administrator
Administrator
Administrator
Password
password
password
password
Administrator
Default Upgrade Password
password
password
password
password
Default
Configuration
Access
IP Office Standard Version Installation
IP Office 7.0
Page 13
15-601042 Issue 23e (16 March 2011)
1.2 Control Units
The base of any IP Office system is the system or control unit. It stores the system configuration and controls the system
operation. Each control unit can be customized by adding various base 19 and trunk 22 cards. External expansion
modules can be also be connected to add additional extension and trunk ports.
IP Office Release 7.0 supports the following IP Office control units. Previous IP Office control units are not supported by IP
Office Release 7.0 and are not covered by this documentation.
· IP500v2 Control Unit 199
This control unit has four front slots for IP500 base cards. It has
an internal power supply unit and uses a mandatory SD card
Feature Key dongle. It includes a 2 port ethernet LAN switch
(layer 3 managed) on the rear.
· IP500 Control Unit 202
This control unit has four front slots for IP500 base cards. It has
an internal power supply unit and uses a mandatory smart card
Feature Key dongle. It includes a 2 port ethernet LAN switch
(layer 3 managed) on the rear.
IP Office Standard Version Installation
IP Office 7.0
Page 14
15-601042 Issue 23e (16 March 2011)
System Overview: Control Units
1.3 IP500v2 System Components
The following are the typical components of an IP Office system based on an IP500v2 control unit.
· IP Office IP500v2 System Unit 199
The control unit holds the main configuration and performs the
routing and switching for telephone calls and data traffic. Each
control unit includes 4 slots for optional base cards to support
trunk and phone extension ports.
·
Avaya SD Card 42
This uniquely numbered dongle is used to validate license
keys entered into the system's configuration to enable
features. A dongle is mandatory for correct system operation
even if no licensed features are being used. IP500v2 control
units use an Avaya SD card which is slotted into the rear of
the control unit. This card also provides embedded voicemail
support and storage for system software files.
· IP500 Base Cards 19
The IP500v2 control unit has slots for up to 4 IP500 base cards.
These can be used to add ports for analog extensions, digital
extensions, voice compression channels and other resources.
· IP500 Digital Station Base Card
· IP500 Analog Phone Base Card
· IP500 VCM Base Card
212
209
216
· IP500 Legacy Card Carrier
214
· IP500 4-Port Expansion Base Card
· IP500 TCM8 Base Card
215
· IP500 ETR6 Base Card
213
208
· IP500 Trunk Daughter Cards 22
Many of the IP500 base cards can be fitted with an IP500 daughter
card in order to support various types of trunk connections.
· IP500 Analog Trunk Card
· IP500 BRI Trunk Card
221
· IP500 PRI Trunk Card
222
220
· IP500 Combination Cards 19
These card are pre-paired base and daughter cards. They provide
6 digital station ports, 2 analog phone ports, 10 voice compression
channels and either 4 analog trunk ports or 4 BRI channels (2
ports). The trunk daughter card cannot be removed or replaced
with another type.
· IP400 Cards 24
The IP500 Legacy Carrier base card can be used to allow IP400
trunk cards and IP400 VCM cards to be added to the IP500 control
unit.
VK00nDd15SDvXoxkw9cR9x_jOXr_AWz9
IP Office Standard Version Installation
IP Office 7.0
· License Keys 396
Various IP Office features and applications require a license key to
be entered into the system's configuration. Each key is a 32character text string unique to the feature being activated and the
serial number of the Feature Key dongle installed in the system.
Page 15
15-601042 Issue 23e (16 March 2011)
· IP500 External Expansion Modules 26
Additional ports can be added using a number of IP500 external
expansion modules. Support also includes IP400 external
expansion modules 31 .
· Systems running in IP Office Essential Edition - PARTNER®
Version, IP Office Essential Edition - Norstar Version or IP
Office Essential Edition - Quick Version mode support up to 8
external expansion modules so long as the system extensions
limit is not exceeded.
· Systems running in IP Office Standard Version mode support
8 external expansion modules or 12 if the control unit is fitted
with an IP500 4-Port Expansion Base Card.
· Power Supplies 33
The IP500 control unit has an internal power supply unit. Each
external expansion module is supplied with an external power
supply unit. Additional power supply units may also be required for
IP phones and some phone add-ons.
· Power Cords 34
Depending on the locale, different power cords need to be ordered
for each control unit, external expansion module and any phones
or devices using external power supply units.
· Cables 36
The IP Office is designed primarily for connection to a structured
cabling system using CAT3 UTP cabling. This approach allows
telephone and data traffic to share the same wiring infrastructure
and simplifies equipment moves.
· Mounting Kits 40
The control unit can be used free-standing, with external
expansion modules stacked above it. With optional rack mounting
kits, the control unit and external expansion modules can also be
rack mounted. Alternatively with an optional wall mounting kit the
IP500 control unit can be wall mounted. IP500 external expansion
modules can also be wall mounted.
· Surge Protectors and Barrier Boxes 39
Where the installation includes extensions in other buildings
additional protective equipment is required. This equipment may
also be required in areas where the lightning risk is high.
· Phones 43
IP Office systems support a variety of Avaya digital and IP phones
plus analog phones.
· Application DVDs
The IP Office applications can be ordered on a number of DVDs. In
addition they can be downloaded from the IP Office section of the
Avaya support web site (http://support.avaya.com).
IP Office Standard Version Installation
IP Office 7.0
Page 16
15-601042 Issue 23e (16 March 2011)
System Overview: IP500v2 System Components
1.4 IP500 Office System Components
This page set to appear in standard mode only.
The following are the typical components of an IP Office system based on an IP500 control unit.
· IP Office IP500 Control Unit 14
The control unit holds the main configuration and performs the
routing and switching for telephone calls and data traffic. Each
control unit includes 4 slots for optional base cards to support
trunk and phone extension ports.
·
Feature Key Dongle 42
This uniquely numbered dongle is used to validate license
keys entered into the system's configuration to enable
features. For IP500 control units, a dongle is mandatory for
correct system operation even if no licensed features are
being used. IP500 control units use a Smart Card which is
slotted into the rear of the control unit.
· IP500 Base Cards 19
The IP500 control unit has slots for up to 4 IP500 base cards.
These can be used to add ports for analog extensions, digital
extensions, voice compression channels and other resources.
· IP500 Digital Station Base Card
· IP500 Analog Phone Base Card
· IP500 VCM Base Card
212
209
216
· IP500 Legacy Card Carrier
214
· IP500 4-Port Expansion Base Card
208
· IP500 Trunk Daughter Cards 22
Many of the IP500 base cards can be fitted with an IP500 daughter
card in order to support various types of trunk connections.
· IP500 Analog Trunk Card
· IP500 BRI Trunk Card
221
· IP500 PRI Trunk Card
222
220
· IP400 Cards 24
The IP500 Legacy Carrier base card can be used to allow IP400
trunk cards and IP400 VCM cards to be added to the IP500 control
unit.
VK00nDd15SDvXoxkw9cR9x_jOXr_AWz9
· License Keys 396
Various IP Office features and applications require a license key to
be entered into the system's configuration. Each key is a 32character text string unique to the feature being activated and the
serial number of the Feature Key dongle installed in the system.
· IP500 External Expansion Modules 26
Additional ports can be added using a number of IP500 external
expansion modules. Support also includes IP400 external
expansion modules 31 . Up to 8 external expansion modules are
supported or 12 if the control unit is fitted with an IP500 4-Port
Expansion Base Card.
IP Office Standard Version Installation
IP Office 7.0
Page 17
15-601042 Issue 23e (16 March 2011)
· Power Supplies 33
The IP500 control unit has an internal power supply unit. Each
external expansion module is supplied with an external power
supply unit. Additional power supply units may also be required for
IP phones and some phone add-ons.
· Power Cords 34
Depending on the locale, different power cords need to be ordered
for each control unit, external expansion module and any phones
or devices using external power supply units.
· Cables 36
The IP Office is designed primarily for connection to a structured
cabling system using CAT3 UTP cabling. This approach allows
telephone and data traffic to share the same wiring infrastructure
and simplifies equipment moves.
· Mounting Kits 40
The control unit can be used free-standing, with external
expansion modules stacked above it. With optional rack mounting
kits, the control unit and external expansion modules can also be
rack mounted. Alternatively with an optional wall mounting kit the
IP500 control unit can be wall mounted. IP500 external expansion
modules can also be wall mounted.
· Surge Protectors and Barrier Boxes 39
Where the installation includes extensions in other buildings
additional protective equipment is required. This equipment may
also be required in areas where the lightning risk is high.
· Phones 43
IP Office systems support a variety of Avaya digital and IP phones
plus analog phones.
· Application DVDs
The IP Office applications can be ordered on a number of DVDs. In
addition they can be downloaded from the IP Office section of the
Avaya support web site (http://support.avaya.com).
· Embedded Voicemail Memory Card 25
This optional card can be used to support embedded voicemail.
IP Office Standard Version Installation
IP Office 7.0
Page 18
15-601042 Issue 23e (16 March 2011)
System Overview: IP500 Office System Components
1.5 Control Unit Cards
1.5.1 IP500 Base Cards
The IP500 and IP500v2 control units have 4 slots for the insertion of IP500
base cards. The slots are numbered 1 to 4 from left to right. Normally they
can be used in any order, however if the capacity for a particular type of
card is exceeded, the card in the rightmost slot will be disabled.
Each base card includes an integral front panel with ports for cable
connections. Typically the first 8 ports on the left are for connection of
extension devices. The 4 ports on the left are used for connection of trunks
if a trunk daughter card 22 is added to the base card.
IP500 Digital Station Base Card
212
This card provides 8 DS (digital station) ports for the connection of
Avaya digital phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 3 per control unit.
· 4400 Series phones (4406D, 4412D and 4424D) are not
supported on this card. They are supported on external
expansion module DS ports.
· Connections for 4100, 7400, M-Series and T-Series phones use
the IP500 TCM8 Digital Station card.
IP500 Analog Phone Base Card
209
The card is available in two variants, supporting either 2 or 8 analog
phone ports.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 4 per control unit.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP500 TCM8 Digital Station Card
215
This card provides 8 TCM (digital station) ports for the connection of
Avaya 4100, 7400, M-Series and T-Series phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 4 per control unit per IP500v2 control unit. Not
supported by IP500 control units.
IP500 VCM Base Card
216
This card is available in variants supporting either 32 or 64 voice
compression channels for use with VoIP calls.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 2 per control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 19
15-601042 Issue 23e (16 March 2011)
IP500 Legacy Card Carrier Base Card
214
This card allows various IP400 trunk cards 24 and IP400 VCM cards 25
to be used. The front of the card includes panels that can be removed
to match the trunk card fitted.
· This card does not accept any IP500 trunk daughter card.
· Maximum: 2 per control unit.
· IP400 Cards Supported: The following cards are supported.
PRI T1
Dual PRI T1
PRI 30 E1 (1.4)
Dual PRI E1
IP500 4-Port Expansion Base Card
PRI 30 E1R2 RJ45
Dual PRI E1R2 RJ45
BRI-8 (UNI)
ANLG 4 Uni (US only)
VCM
VCM
VCM
VCM
VCM
4
8
16
24
30
208
This card adds an additional 4 expansion ports for external expansion modules. The
card is supplied with four 2m yellow interconnect cables.
· This card does not accept any IP500 trunk daughter card.
· Maximum: 1 per control unit (Right-hand slot 4 only).
· Supported Expansion Modules: The following external expansion modules are
supported:
·
·
·
·
IP500 BRI Combination Card
IP500
IP500
IP500
IP500
Analogue Trunk Module
BRI So Module
Digital Station Modules
Digital Station Modules A
· IP500 Phone Module
· IP400 Digital Station V2 Modules
· IP400 Phone V2 Modules
211
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 2 BRI trunk ports (9-10, 4 channels). The card also includes
10 voice compression channels.
· This card has a pre-installed IP500 BRI trunk daughter card
22
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type. Not supported by IP500 control units.
· IP Office Essential Edition - Norstar Version and IP Office
Essential Edition - Quick Version mode systems are limited to a
maximum of 12 BRI channels using BRI Combination and or BRI
trunk daughter cards.
IP500 ATM Combination Card
210
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 4 analog trunk ports (9-12). The card also includes 10 voice
compression channels.
· This card has a pre-installed IP500 analog trunk daughter card
22
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type. Not supported by IP500 control units.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP Office Standard Version Installation
IP Office 7.0
Page 20
15-601042 Issue 23e (16 March 2011)
System Overview: Control Unit Cards
IP500 ETR6 Base Card
213
This card is only supported in an IP500v2 control unit running in IP
Office Essential Edition - PARTNER® Version or IP Office Essential
Edition - Quick Version mode. It is not supported in IP Office Essential
Edition - Norstar Version or IP Office Standard Version modes.
It provides 6 ETR ports for connection of ETR phones. 2 Analog
extension ports are also provided for emergency use only with an
analog trunk card.
· The card can be fitted with an IP500 trunk daughter card which uses
the base card ports for trunk connection.
· Maximum: 3 per IP500v2 control unit. Not supported by IP500
control units.
· The analog phone ports do not include a ringing capacitor. Where this
is a requirement, connection should be via a Master socket containing
ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone ports 7 and 8 are connected to analog trunk port 12.
However during normal operation analog phone ports 7 and 8 are not
useable.
IP Office Standard Version Installation
IP Office 7.0
Page 21
15-601042 Issue 23e (16 March 2011)
1.5.2 IP500 Trunk Cards
Most IP500 base cards 19 can be fitted with an IP500 trunk daughter
cards to support the connection of trunks to the base card.
Each daughter card is supplied with the stand off pillars required for
installation and a label to identify the daughter cards presence on the
front of the base card after installation.
· IP500 Combination cards are pre-fitted with a trunk daughter card
which cannot be removed or changed for another type of trunk
daughter card.
IP500 Analog Trunk Daughter Card
220
This card allows the base card to support 4 analog loop-start trunks.
· The analog phone ports do not include a ringing capacitor.
Where this is a requirement, connection should be via a Master
socket containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during
power failure phone port 8 is connected to analog trunk port
12.
· Maximum: 4 per control unit.
IP500 PRI-U Trunk Daughter Card
222
This card allows the base card to support up to 2 PRI trunk
connections. The card is available in single and dual port variants.
The card can be configured for E1 PRI, T1 robbed bit, T1 PRI or E1R2
PRI trunks.
· Maximum: 4 per control unit.
· The IP Office system supports 8 unlicensed B-channels on each
IP500 PRI-U port fitted. Additional B-channels, up to the capacity
of ports installed and PRI mode selected require IP500 Universal
PRI (Additional Channels) 388 licenses added to the
configuration. These additional channels consume the licenses
based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by
licensing.
IP500 BRI Trunk Daughter Card
221
This card allows the base card to support up to 4 BRI trunk
connections, each trunk providing 2B+D digital channels. The card is
available in 2 port (4 channels) and 4 port (8 channels) variants.
· Maximum: 4 per control unit.
· S-Bus Connection: The card can be switched from To trunk mode
to So mode. This mode requires additional terminating resistors
and an ISDN crossover cable connection, see BRI Port (So) 374 .
· IP Office Essential Edition - Norstar Version and IP Office
Essential Edition - Quick Version mode systems are limited to
a maximum of 12 BRI channels using BRI Combination and or
BRI trunk daughter cards.
IP Office Standard Version Installation
IP Office 7.0
Page 22
15-601042 Issue 23e (16 March 2011)
System Overview: Control Unit Cards
IP Office Standard Version Installation
IP Office 7.0
Page 23
15-601042 Issue 23e (16 March 2011)
1.5.3 IP400 Trunk Cards
IP400 trunk cards can be used in IP500 and IP500 v2 controls units by being fitted onto an IP500 Legacy Card Carrier
base card. Up to 2 cards can be added to the control unit in this way.
214
The following IP400 trunk card types are supported in this way by IP Office Release 7.0:
IP400 Trunk Cards
IP500
IP500v
2
Analog Trunk Card (ATM4) 241
Provides 4 RJ45 loop-start analog trunk ports. The card is available in several
locale specific variants. This card has been superseded by the ATM4U card
below.
Additional loop or ground start analog trunks can also be added using Analog
Trunk 248 external expansion modules.
Analog Trunk Card (ATM4U) 240
Provides 4 RJ45 loop-start analog trunk ports as per the ATM4 above but
available in a single worldwide variant. Also supports adjustable echo
cancellation on IP Office 3.1.
Additional loop or ground start analog trunks can also be added using Analog
Trunk 248 external expansion modules.
Quad BRI Trunk Card 241
Provides support for 4 RJ45 BRI (2B+D) trunk ports. These can be configured
to ETSI or AusTS013 operation. The ports include 100ohm termination.
Single PRI T1 Trunk Cards 242
Supports PRI (23B+D) trunks and T1 Robbed-Bit (24B) trunks through a single
RJ45 port. The mode of operation is selected in the IP Office configuration.
Single E1 PRI Trunk Cards 242
Supports PRI (30B+D) trunks through a single RJ45 port. The port can be
configured for PRI or QSIG operation.
Single E1R2 Trunk Cards 243
Supports PRI (30B+D) trunks using E1R2 signaling. Available in coaxial or
RJ45 connector variants. Coaxial variants are not supported on an IP500
carrier card.
Dual PRI Trunk Cards 242
As the single PRI cards above but supporting the connection of two PRI trunks.
On the IP406 V2, supported in Slot A only.
IP Office Standard Version Installation
IP Office 7.0
Page 24
15-601042 Issue 23e (16 March 2011)
System Overview: Control Unit Cards
1.5.4 Other Cards
Each IP Office control unit can be fitted with a number of internal cards. The cards supported depend on the control unit
type.
Embedded Voicemail Memory Cards
These cards provide message and prompt storage space for embedded voicemail and auto-attendant
options. The cards used are specially formatted compact flash cards.
· The IP500v2 control unit uses its SD Feature Key dongle card for embedded voicemail and file
storage.
Embedded Voicemail Memory Cards
SAP Code
IP406 V2 Memory Card: 244
Supports a 512MB Compact Flash card.
This provides up to 15 hours of
uncompressed message storage.
700343460
IP500
IP500v2
–
· Memory cards in these slots can also be used for storage of files normally obtained via TFTP transfer. For example
the music-on-hold .wav file and supported Avaya phone software files. This will however reduce storage space for
prompt and message files if embedded voicemail is being used.
· IP Office systems that have downloaded an internal music on hold source can then backup and restore that music
on hold to and from the memory card.
· Non-Avaya cards can be used for file storage but will not support Embedded Voicemail.
IP400 Voice Compression Modules
VCM cards are used to provide voice compression channels for calls between IP and non-IP
devices, devices being both trunks and extensions. VCM cards with differing numbers of
voice compression channels are available.
· For IP500 and IP500v2 control units, voice compression channels can be added using
combinations of IP400 VCM modules mounted on an IP500 Carrier Card, IP500 VCM cards
and IP500 Combination cards.
VCM Cards
25ms echo
cancellation.
64ms echo
cancellation.
SAP Code
IP500
IP500v2
IP400 VCM5*
700185119
–
–
IP400 VCM10*
700185127
–
–
IP400 VCM20*
700185135
–
–
IP400 VCM30
700293939
IP400 VCM4
700359854
IP400 VCM8
700359862
IP400 VCM16
700359870
IP400 VCM24
700359888
2
2
128
148
Number of IP400 VCM cards.
Maximum number of channels.
· *These modules are still supported but are no longer available from Avaya.
IP Office Standard Version Installation
IP Office 7.0
Page 25
15-601042 Issue 23e (16 March 2011)
1.6 External Expansion Modules
These modules can be used to add additional ports to an IP Office systems. The number of external expansion modules
supported depends on the control unit type. Each module uses an external power supply unit 33 supplied with the
module. A locale specific power cord 34 for the PSU must be ordered separately.
IP500 System with External Expansion Module
· Systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version or
IP Office Essential Edition - Quick Version mode support up to 8 external expansion modules so long as the system
extensions limit is not exceeded.
· Systems running in IP Office Standard Version mode support 8 external expansion modules or 12 if the control unit
is fitted with an IP500 4-Port Expansion Base Card.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
IP500 External Expansion Modules
Expansion modules include an external power supply unit (PSU) and a 1m blue interconnect cable. They do not include a
locale specific power cord for the external PSU or any phone extension cables.
Variant
Country
SAP Code
Digital Station
IPO 500 Digital Station 16
All
700449499
IPO 500 Digital Station 30
All
700426216
IPO 500 Digital Station 16A
All
700500699
IPO 500 Digital Station 30A
All
700500698
IPO 500 Phone 16
All
700449507
IPO 500 Phone 30
All
700426224
IPO 500 Analog Trunk 16
US
700449473
IPO 500 BRI So8
All
700449515
Analog Phone
Others
IP Office Standard Version Installation
IP Office 7.0
Page 26
15-601042 Issue 23e (16 March 2011)
System Overview: External Expansion Modules
IP400 External Expansion Modules
Expansion modules include an external power supply unit (PSU) and a 1m blue interconnect cable. They do not include a
locale specific power cord for the external PSU or any phone extension cables.
Variant
Country
SAP Code
North America
700211360
Europe
700241680
New Zealand
700241698
IP400 Digital Station 16 V2
All
700359839
IP400 Digital Station 30 V2
All
700359847
IP400 Digital Station 16
All
700184807
IP400 Digital Station 30
All
700184880
IP400 Phone 8 V2
All
700359896
IP400 Phone 16 V2
All
700359904
IP400 Phone 30 V2
All
700359912
IP400 Phone 8
All
700184773
IP400 Phone 16
All
700184781
IP400 Phone 30
All
700184799
All
700185077
Analog Trunk
IP400 Analog Trunk 16
Digital Station
Phone
S0 (BRI)
IP400 So8
IP Office Standard Version Installation
IP Office 7.0
Page 27
15-601042 Issue 23e (16 March 2011)
Connecting External Expansion Modules
The integral expansion ports on a control unit are located on the rear of the unit. For IP500 and IP500v2 control units, an
additional 4 expansion ports can be added to the front of the control unit by installing an IP500 4-Port Expansion card.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
IP Office Standard Version Installation
IP Office 7.0
Page 28
15-601042 Issue 23e (16 March 2011)
System Overview: External Expansion Modules
1.6.1 IP500 External Expansion Modules
The following IP500 external expansion modules are supported by IP Office Release 7.0. Each module uses an external
power supply unit 33 supplied with the module. A locale specific power cord 34 for the PSU must be ordered separately.
If being rack mounted, these units use the IP500 rack mounting kit. They can be wall mounted using the new wall
mounting kit V2.
· Systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version or
IP Office Essential Edition - Quick Version mode support up to 8 external expansion modules so long as the system
extensions limit is not exceeded.
· Systems running in IP Office Standard Version mode support 8 external expansion modules or 12 if the control unit
is fitted with an IP500 4-Port Expansion Base Card.
· IP500 Digital Station Module 229
Provides, depending on variant, an additional 16 or 30 DS
supported Avaya DS digital phones 43 .
376
ports for
· IP500 Digital Station A Module 231
Provides, depending on variant, an additional 16 or 30 TCM 385 ports for
supported Avaya TCM digital phones 43 . Supported by IP500v2 only.
· IP500 Phone Module 234
Provides, depending on variant, an additional 16 or 30 PHONE
analog phones.
382
ports for
· IP500 BRI So8 Module 227
Provides 8 ETSI BRI-So ports 374 for the connection of ISDN devices. This unit
is not intended to support BRI trunks.
IP Office Standard Version Installation
IP Office 7.0
Page 29
15-601042 Issue 23e (16 March 2011)
· IP500 Analog Trunk Module 225
Provides an additional 16 ANALOG 373 ports for connection of analog trunks.
Supports both loop-start and ground-start trunks.
· Use with ground start trunks requires that the trunk module and the IP Office
control unit are grounded.
· In IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition
- Norstar Version and IP Office Essential Edition - Quick Version modes, only
1 Analog Trunk module is supported.
IP Office Standard Version Installation
IP Office 7.0
Page 30
15-601042 Issue 23e (16 March 2011)
System Overview: External Expansion Modules
1.6.2 IP400 External Expansion Modules
The following IP400 external expansion modules are supported by IP Office Release 7.0 and can be used with an IP500
and IP500v2 control units. Each module uses an external power supply unit 33 supplied with the module. A locale
specific power cord 34 for the PSU must be ordered separately.
If being rack mounted these units use the IP400 rack mounting kit. If being rack mounted, these units use the IP500 rack
mounting kit. They cannot be wall mounted.
· IP400 Analog Trunk Module (ATM16) 248
Provides an additional 16 ANALOG 373 ports for connection of analog trunks.
Supports both loop-start and ground-start trunks.
· Available in a number of variants for different locales.
· Use with ground start trunks requires that the trunk module and the IP
Office control unit are grounded.
· IP400 Digital Station Module 252
Provides, depending on the variant, an additional 16 or 30 DS 376 ports for
supported Avaya digital phones. This module has been superseded by the
Digital Station V2.
· IP400 Digital Station Module V2 250
Provides, depending on variant, an additional 16 or 30 DS 376 ports for
supported Avaya digital phones 43 . Supersedes the previous Digital Station
module.
· IP400 Phone Module 256
Provides, depending on variant, an additional 8, 16 or 30 POT 382 ports for
analog phones. This module has been superseded by the Phone Module V2.
· IP400 Phone Module V2 254
Provides, depending on variant, an additional 8, 16 or 30 PHONE 382 ports for
analog phones. Supersedes the previous Phone module. With IP Office 3.1,
the Phone V2 supports a wider range of message waiting indication (MWI)
options than Phone V1 modules.
· With V2 units, the labeling of analog phone ports was changed from POT to
PHONE.
IP Office Standard Version Installation
IP Office 7.0
Page 31
15-601042 Issue 23e (16 March 2011)
· IP400 So8 Module 258
Provides 8 ETSI BRI-So 374 ports for the connection of ISDN devices. This
unit is not intended to support BRI trunks.
IP Office Standard Version Installation
IP Office 7.0
Page 32
15-601042 Issue 23e (16 March 2011)
System Overview: External Expansion Modules
1.7 Power Supplies and Cables
All IP Office control units and external expansion modules either have an internal power supply unit or are supplied with
an external power supply unit.
1.7.1 Power Supplies
The IP500 and IP500v2 control units have an internal power supply unit and so only require a suitable locale specific
power cord 34 and a power outlet that includes a switch. Note that if the power cord includes an earth lead, the power
outlet must be connected to a protective earth.
External expansion modules are all supplied with an external power supply unit (PSU). These PSUs include an integral 1.5
meter lead for connection to the control unit or expansion module. A power cord 34 for connection from the PSU to the
power outlet is not included as this varies by locale. The appropriate power cord must be ordered separately or sourced
locally.
Additional power supply units are required for 4450, EU24, XM24 and T3 DSS add-on modules and may also be required
for Avaya IP phones.
Area
Type
Used on:
Connector Type
Analog, Digital Station V1, Phone V1.
IEC60320 C7
60W Earthed
PSU
IP400 Digital Station V2, IP400 Phone V2, IP400 So8, IP500
Phone 30, IP500 Digital Station 30, IP500 Digital Station
16A, IP500 Digital Station 30A.
IEC60320 C13
1151D1
All phones with XM24 Phone add-ons.
All phones with EU24/EU24BL Phone add-ons unless using
Class 3 PoE.
4600 and 56000 Series IP Phones when not using a PoE.
IEC60320 C13
Plug-top PSU used with 1600 Series phones on IP Office
when not being power using PoE.
Various country
variants.
IP Office Control 40W PSU
Units and
External
Expansion
Modules
IP Phones and
Phone Add-Ons
1151D2
1600PWR 5V
· The 1151D2 is the same as the 1151D1 except that it includes a backup battery that is charged during normal
operation. This can provide typically 15 minutes backup at maximum load (20 Watts) and up to 8 hours at light
load (2 Watts).
· Avaya IP phones can use IEEE 802.3af Power over Ethernet (PoE) power supplies. Refer to the IP Office IP Phone
Installation Manual for full details.
IP Office Standard Version Installation
IP Office 7.0
Page 33
15-601042 Issue 23e (16 March 2011)
1.7.2 Power Supply Cords
Each control unit and expansion module requires a switched power outlet socket rated at 110-240V ac, 50-60Hz.
Connection from that power outlet socket requires an appropriate locale specific power cord which is not supplied with the
unit and must be ordered separately. Note that if the power cord includes an earth lead, the power outlet must be
connected to a protective earth.
Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing of the
power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment near a socket
outlet.
For locales not detailed below an appropriate power cord must be obtained locally.
Power Cord Type
Power Outlet Plug Type
Locales
SAP Codes
Earthed Power Cords (IEC60320 C13)
CEE7/7 (Schuko)
Europe and
South Africa.
700289762
Control Units
· IP500v2.
· IP500.
BS1363
Czech Republic, 700289747
Ireland, United
Kingdom.
NEMA5-15P / CS22.2
No.42
North, Central
and South
America.
700289770
Unearthed Power Cord (IEC60320 C7)
CEE7/16 (Europlug)
Europe and
South Africa.
700213382
IP400 External Expansion Modules
· Analog.
· Digital Station V1.
· Phone V1.
BS1363
Czech Republic, 700213374
Ireland, United
Kingdom.
NEMA1-15
North, Central
and South
America.
700213390
Korea.
700254519
IP400 External Expansion Modules
· Digital Station V2.
· Phone V2.
· So8.*
IP500 External Expansion Modules
· BRI So8.
· Digital Station 16/30.
· Phone 16/30.
IP500 External Expansion Modules
· Analog Trunk 16.
*Older units were supplied with a 40W unearthed PSU and required an IEC60320 C7 power cord.
IP Office Standard Version Installation
IP Office 7.0
Page 34
15-601042 Issue 23e (16 March 2011)
System Overview: Power Supplies and Cables
1.7.3 Power Supply Backup
The use of an Uninterrupted Power Supply (UPS) with any telephone system is strongly recommended. Even at sites that
rarely lose electrical power, that power may occasionally have to be switched off for maintenance of other equipment. In
addition, most UPSs also provide an element of power conditioning, reducing spikes and surges.
The capacity of UPS systems and the total equipment load the UPS is expected to support are usually quoted in VA. Where
equipment load is quoted in Watts, multiply by 1.4 to get the VA load.
The calculation of how much UPS capacity is required depends on several choices.
· What equipment to place on the UPS?
Remember to include server PCs such as the voicemail. It is recommended that the total load on a new UPS is
never greater than 75% capacity, thus allowing for future equipment.
· How many minutes of UPS support is required?
Actual UPS runtime is variable, it depends on what percentage of the UPSs capacity the total equipment load
represents. For example, a 1000VA capacity UPS may only support a 1000VA (100%) load for 5 minutes. This
relationship is not linear, the same UPS would support a 500VA (50%) load for 16 minutes. Therefore the lower the
percentage of capacity used, the increasingly longer the UPS runtime, typically up to 8 hours maximum. Remember
also that for most UPS's the ratio of discharge to full recharge time is 1:10.
· How many output sockets does the UPS provide?
Multiple UPS units may be required to ensure that every item of supported equipment has its own supply socket.
The web site http://www.avayaups.com provides a calculator into which you can enter the equipment you want supported
on a UPS. It will then display various UPS options. The site uses VA values for typical IP Office systems. However, if more
specific values are required for a particular system, the table below can be used to enter values.
Typical IP Office System
VA
Typical IP Office System
VA
IP500v2 System
230
IP500 System
230
Individual Equipment
VA
Individual Equipment
VA
Analog 16 Module
88
Phone 30 Module
42
Digital Station 16 Module
34
Typical Server PC
600
Digital Station 30 Module
42
Typical Desktop PC
400
Phone 8 Module
17
Mid Span PSU - 6 ports
150
Phone 16 Module
23
Mid Span PSU - 12/24 ports
300
So8 Module
34
· The 1151D2 power supply unit for Avaya H.323 IP phones includes a backup battery. This typically provides 15 minutes
backup at maximum load (20 Watts) and up to 8 hours at light load (2 Watts).
IP Office Standard Version Installation
IP Office 7.0
Page 35
15-601042 Issue 23e (16 March 2011)
1.7.4 Cabling and Cables
The IP Office systems are designed primarily for use within an RJ45 structured cabling system using CAT3 unshielded
twisted-pair (UTP) cabling and RJ45 sockets.
A structured cabling system is one where cables are run from a central RJ45 patch panel in the communications/data room
to individual RJ45 sockets at user locations. All wires in each cable between the patch panel and the desk socket are
connected straight through. This arrangement allows devices connected at the patch panel to be swapped to match the
type of device that needs to be connected at the user socket. For example, making one user socket a phone port and
another user socket a computer LAN port, without requiring any rewiring of the cables between the patch panel and the
user location.
· Traditional IDC Punchdown Wiring Installations
Where necessary, the far end RJ45 plug can be stripped from IP Office cables and wired into traditional wiring
systems using punch-block connectors. This type of installation should be performed by an experienced wiring
technician.
· Trunk Connections
The majority of IP Office trunk ports use RJ45 connectors for acceptance of an RJ45-to-RJ45 cable. However,
connection at the line provider's end may require use of a different plug type in order to match the line providers
equipment.
· RJ11 Phone Connectors
Many phones use RJ11 sockets and are supplied with RJ11-to-RJ11 cables. RJ11 plugs can be inserted into RJ45
sockets and in many case the connection will work. However this is not recommended or supported as the
connection lock is not truly positive and may become disconnected. An RJ45-to-RJ11 cable 376 is available for these
connections.
IP Office Standard Version Installation
IP Office 7.0
Page 36
15-601042 Issue 23e (16 March 2011)
System Overview: Power Supplies and Cables
Standard IP Office Cables
The following are Avaya standard cables available for use with IP Office systems. The maximum length is applicable if the
standard Avaya cable is replaced with an alternate cable.
Cable
9-Way DTE Cable
144
Description
SAP Code
Standard
Length
Maximum
Length
Connects to control unit RS232 DTE port. 9Way D-type plug to 9-way D-type socket.
–
2m/6'6''.
2m/6'6''.
Structured Cabling DS Line
Cable 376
Connects from RJ45 sockets to RJ11 socketed TT700047871 4m/13'2''.
DS and analog phones.
See table
below.
BRI/PRI Trunk Cable
375
Connects BRI/PRI trunk ports to the line
700213440
provider's network termination point. RJ45 to
RJ45. Red.
3m/9'10''.
–
Expansion Interconnect
Cable 379
Connects the control unit to expansion
700213457
modules. RJ45 to RJ45. Blue. May be replaced
by a yellow interconnect cable (2m (6'6") 700472871) supplied with the IP500 4-Port
Expansion 208 card when using that card.
1m/3'3''.
1m/3'3''.
LAN Cable
Connects from IP Office LAN ports to IP
devices. RJ45 to RJ45. Grey.
3m/9'10''.
100m/328'.
380
700213481
The table below details the maximum total cable distances for DS and analog extensions using different cable types.
Unshielded Twisted-Pair (UTP) - 50nf/Km
Telephone
CW1308
AWG22
(0.65mm)
AWG24
(0.5mm)
AWG26
(0.4mm)
1400 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
2400/5400 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
4406D Phone
1000m/3280'.
1000m/3280'.
400m/1310'.
400m/1310'.
4412D Phone
1000m/3280'.
700m/2295'.
400m/1310'.
400m/1310'.
4424D
500m/1640'.
500m/1640'.
400m/1310'.
400m/1310'.
6400 Series
1000m/3280'.
1000m/3280'.
400m/1310'.
400m/1310'.
9400/9500 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
T3 Series (Upn)
1000m/3280'.
1000m/3280'.
400m/1310'.
–
TCM (without power
booster)
–
305m/1000'
–
–
" (with power
booster)
–
790m/2600'
–
–
Analog Phones
1000m/3280'.
1000m/ 3280'.
400m/1640'.
800m/2620'.
305m/1000'.
305m/1000'.
122m/400'.
122m/400'.
ETR Phones
IP Office Standard Version Installation
IP Office 7.0
Page 37
15-601042 Issue 23e (16 March 2011)
1.7.5 Grounding
All IP Office control units and external expansion modules must be connected to a functional ground. Where the unit is
connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective
earth.
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially
important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and
data networks.
In some cases, such as ground start trunks, in addition to being a protective measure, this is a functional requirement for
the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for
example areas of high lightning risk.
·
WARNING
During installation do not assume that ground points are correctly connected to ground. Test ground points before
relying on them to ground connected equipment.
or
symbol. Ground
The ground point on IP Office control units and external expansion modules are marked with a
connections to these points should use a 14 AWG solid wire with either a green sleeve for a functional ground or green and
yellow sleeve for a protective ground.
· Additional protective equipment
In addition to grounding, additional protective equipment will be required in the following situations. Refer to "Out
of Building Telephone Installations 39 ".
· On any Digital Station or Phones external expansion module connected to an extension located in another
building.
· In the Republic of South Africa, on all Analog Trunk external expansion modules (ATM16) and on any control
units containing an analog trunk cards (ATM4/ATM4U).
IP Office Standard Version Installation
IP Office 7.0
Page 38
15-601042 Issue 23e (16 March 2011)
System Overview: Power Supplies and Cables
1.7.6 Lightning Protection/Out-of-Building Connections
The following are the only supported scenarios in which wired extensions and devices outside the main building can be
connected to the IP Office system. In these scenarios, additional protection, in the form of protective grounding and surge
protectors, must be fitted.
·
WARNING
The fitting of additional protection does not remove the risk of damage. It merely reduces the chances of damage.
· Cables of different types, for example trunk lines, phone extensions, ground and power connections, should be kept
separate.
· All cabling between buildings should be enclosed in grounded ducting. Ideally this ducting should be buried.
· A Primary Protection Box must be provided at the point where the cables enter the building. This should be three
point protection (tip, ring and ground). Typically this would be gas tube protection provided by the local telephone
company. The ground wire must be thick enough to handle all the lines being affected by indirect strike at the same
time.
Connection Type
Protection Device Type
Requirement
Analog Phone Extensions
Phones External expansion
module (POT 382 or PHONE 382 )
ports only.
IP Office Barrier Box 133
· Connection from the expansion module to the
Supports a single connection.
phone must be via a surge protector at each end
Maximum of 16 on any expansion
and via the primary protection point in each
module.
building.
DS Phone Extensions
ITWLinx towerMAX DS/2 132
External expansion module DS Supports up to 4 connections.
376 ports only.
(This device was previously
referred to as the Avaya 146E).
TCM Phone Extensions
None
Analog Trunks
ITWLinx towerMAX CO/4x4
ITWLinx towerMAX SCL/8
(This device was previously
referred to as the Avaya 146G)
· The between building connection must be via
earthed ducting, preferable underground. The cable
must not be exposed externally at any point.
Currently not supported.
132
Supports up to 4 two-wire lines.
(This device was previously
referred to as the Avaya 146C).
External Output Switch
· The IP Office expansion module and control unit
and IROB devices must be connected to the
protective ground point in their building.
For installations in the Republic of South Africa, the
fitting of surge protection on analog trunks is a
requirement.
For other locations where the risk of lightning strikes
is felt to be high, additional protection of incoming
analog trunks is recommended.
Connections from an IP Office Ext O/P port to an
external relay device must be via a surge protector.
The towerMAX range of devices are supplied by ITWLinx (http://www.itwlinx.com).
IP Office Standard Version Installation
IP Office 7.0
Page 39
15-601042 Issue 23e (16 March 2011)
1.8 Wall and Rack Mounting
All the IP Office control units are designed to be free-standing. On systems with external expansion modules, the control
unit and modules are intended to be stacked.
Using additional option mounting kits, some systems can be wall or rack mounted.
Control/Expansion Unit
Wall Mount
Rack
Mount
IP500 Control Unit
IP500v2 Control Unit
IP500 External Expansion Modules
IP400 External Expansion Modules
–
Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Standard Version Installation
IP Office 7.0
Page 40
15-601042 Issue 23e (16 March 2011)
System Overview: Wall and Rack Mounting
Rack Mounting
All IP Office control units and external expansion modules can be rack mounted into standard 19" rack systems. Each unit
requires a 2U slot space within the rack. Rack mounting requires an IP400 or IP500 rack mounting kit for each control unit
and external expansion module.
Where IP Office systems are being rack mounted, the effect of conditions within the rack cabinet must be considered. For
example the rack temperature may be above the room temperature and airflow within the rack will be restricted. The
environmental requirements 54 for the individual IP Office units are still applicable inside the rack cabinet.
IP500 Rack Mounting Kit
· IP500 Rack Mounting Kit (SAP 700429202)
This kit contains all the components required for the rack mounting of
a single IP500v2 control unit, IP500 control unit or IP500 external
expansion module. This includes screws for fixing of the brackets to
the module, bolts for securing the module in the rack and cable tidy
brackets.
IP400 Rack Mounting Kit
· IP400 Rack Mounting Kit (SAP 700210800)
This kit contains all the components required for the rack mounting of
a single control unit or expansion module. This includes screws for
fixing of the brackets to the module and bolts for securing the module
in the rack.
Barrier Box Rack Mounting Kit
· Barrier Box Rack Mounting Kit (SAP 700293905)
Barrier boxes must be used for out-of-building analog phone
extensions 39 . This bracket allows up to 8 IP Office barrier boxes to
be rack mounted and simplifies the number of connections to the
protective ground point in the rack. This kit must be used when more
than 3 barrier boxes are in use and supports a maximum of 16
barrier boxes for a single external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 41
15-601042 Issue 23e (16 March 2011)
1.9 Feature Keys and Licenses
A feature key is required for licensed features.
· IP500v2 Avaya SD Card 236
Inserts into the System slot on the rear of an IP500v2 control unit. This card is required even if not
using any IP Office licenses.
· IP500 Smart Card 238
Inserts into a dedicated slot on the rear of the IP500 control unit. This card is required even if not using
any IP Office licenses.
Various IP Office features and applications require entry of license keys into the system's configuration. The license keys
are unique 32-character codes based on the feature being activated and the serial number of the feature key dongle 236
installed with the IP Office system.
The serial number is printed on the feature key dongle and prefixed with SN (IP500) or FK (IP500v2). It can also be
viewed in the system configuration using IP Office Manager.
· For IP500 and IP500v2 systems, the feature key dongle takes the form of a card (smart media or SD card
respectively) inserted into the control unit. The card is a mandatory item for these systems even if they use no
licensed features.
·
When a license key is entered into the IP Office configuration, the following information is shown.
· Status
The status, which is Unknown until the configuration file is sent back to the IP Office system.
· Unknown
This status is shown for licenses that have just been added to the configuration shown in IP Office Manager.
Once the configuration has been sent back to the IP Office and then reloaded, the status will change to one of
those below.
· Valid
The features licensed can be configured and used.
· Invalid
The license was not recognized. It did not match the serial number of the Feature Key.
· Dormant
The license is valid but is conditional on some other pre-requisite licenses.
· Obsolete
The license is valid but is one no longer used by the level of software running on the IP Office system.
· Expired
The license has gone past its expiry date.
· License
The name of the licensed feature. This may differ from the ordered RFA name.
· Instances
Depending on the license, this may be the number of ports enabled or number of simultaneous users of the
licensed feature. Sometime the number of instances is specified in the license name.
· Expires
Most purchased licenses have no expiry setting. For some features, trial licenses may be available which will have
an expiry date.
IP Office Standard Version Installation
IP Office 7.0
Page 42
15-601042 Issue 23e (16 March 2011)
System Overview: Feature Keys and Licenses
1.10 IP Office Phones
IP Office Release 7.0 supports the following phones and phone add-ons. Availability may depend on location and may be
subject to local restrictions.
Enhanced Tip and Ring (ETR Port)
These phones are only supported on an ETR6 card in a IP500v2 systems. They are only supported in IP Office Essential
Edition - PARTNER® Version and IP Office Essential Edition - Quick Version mode systems running a North American
locale. They are not supported in IP Office Essential Edition - Norstar Version and IP Office Standard modes.The following
are supported in mode.
· ETR Series: ETR6 322 , ETR6D 322 , ETR18
2 per card and 4 in total)
· PARTNER DECT: 3910 290 , 3920 290
323 ,
ETR18D
323 ,
ETR34D
324
(ETR 34D phones limited to a maximum of
Digital Station (DS Port)
These digital stations connect to the IP Office via DS 376 ports. The following are supported in IP Office Essential Edition PARTNER® Version, IP Office Essential Edition - Norstar Version, IP Office Essential Edition - Quick Version and IP Office
Standard Version modes.
· 1400 Series: 1403
· 9400 Series: 9404
· 9500 Series: 9504
266 ,
267 ,
308 ,
1408
9408
309 , 9508
308
1416
268
309
The following are only supported in IP Office Standard Version mode:
· 2400 Series: 2402 275 , 2410 276 , 2420 277 .
· 3800 Series: 3810 Wireless phone 289 .
· 4400 Series: 4406D 291 , 4412D+ 292 , 4424D+ 293 (Not supported on the IP500 and IP500v2 control unit DS
ports)
· 5400 Series: 5402 300 , 5410 301 , 5420 302 .
· T3 (Upn) Series: T3 Compact 336 , T3 Classic 334 , T3 Comfort 335 .
Digital Station (TCM Port)
These digital stations connect to the IP500v2 IP Office system via TCM 385 ports. The following are supported in IP Office
Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version, IP Office Essential Edition - Quick
Version and IP Office Standard Version modes.
· 4100 Series: 4135, 4136, 4145, 4145EX, 4146, 4146EX - Connection to IP Office TCM ports via a Digital Mobility
Solution 349 system.
· 7400 Series: 7420, 7430, 7434, 7439, 7440, 7444, 7449 - Connection to IP Office TCM ports via a Digital Mobility
Solution 349 system.
· ACU: Audio Conferencing Unit 321
· M-Series: MT7100 325 , MT7100N 325 , MT7208 326 , MT7208N 326 , M7310 327 , M7310N 327 , M7324 328 , M7324N 328
.
· T-Series: T7000 329 , T7100 329 , T7208 330 , T7316 331 , T7316E 332 , T7406 333 , T7406E 333
IP Telephones
IP Phones (SIP and H323) connect to the IP Office system via the RJ45 LAN or WAN. These device require an Avaya IP
Endpoint license and voice compression resources. They are not supported in IP Office Essential Edition - PARTNER®
Version, IP Office Essential Edition - Norstar Version and IP Office Essential Edition - Quick Version mode.
H323:
· 1600 Series: 1603IP/SW 269 , 1608 271 , 1608-I 271 , 1616 273 , 1616-I 273
· 3600 Series: 3616 278 , 3620 279 , 3626 280 , 3641 281 , 3645 282
· 3700 Series: 3701 283 , 3711 284 - Connection via DECT base stations. 3720 285 , 3725 286 , 3740 287 , 3749 288 Connection via DECT R4 base stations.
· 4600 Series: 4601 294 , 4602 295 , 4602SW 295 , 4610 296 , 4610SW 296 , 4620 297 , 4620SW 297 , 4621SW 298 , 4625
299 .
· 5600 Series: 5601 303 , 5602 304 , 5602SW 304 , 5610 305 , 5620 306 , 5621 307 .
· 9600 Series: 9608 310 , 9620L 311 , 9620C 311 , 9621G 313 , 9630G 314 , 9640 316 , 9640G 316 , 9641G 318 , 9650 319 ,
9650C 319
· T3 IP Series: T3 IP Compact 336 , T3 IP Classic 334 , T3 IP Comfort 335 .
IP Office Standard Version Installation
IP Office 7.0
Page 43
15-601042 Issue 23e (16 March 2011)
SIP:
·
·
·
·
1000 Series: 1010 264 , 1040 264
1100 Series: 1120E 265 , 1140E 265
1200 Series: 1220 265 , 1230 265
Softphone: Avaya IP Office SIP Softphone application.
Analog Telephones
Analog phones and devices connect to PHONE 382 ports with the IP Office system. However due to the variety of analog
phones and device available no guarantee of operation is given. It is the responsibility of the IP Office installer and
maintainer to test and verify the operation of proposed analog equipment.
· 6200 Series: 6211, 6219, 6221 (North America).
· Interquartz Gemini: 9330-AV, 9335-AV, 9281-AV (Europe, Middle East, Africa, Asia-Pacific).
IP Office Standard Version Installation
IP Office 7.0
Page 44
15-601042 Issue 23e (16 March 2011)
System Overview: IP Office Phones
1.11 VoIP
IP Office is a converged telephony system, that is it combines aspects of traditional PABX telephone systems and IP data
and telephony systems. This works at various levels.
· Individual phone users can control the operation of their phone through applications running on their PC.
· Data traffic can be routed from the LAN interface to a telephony trunk interface, for example a dial-up ISP
connection.
· Voice traffic can be routed across internal and external data links. This option is referred to as voice over IP (VoIP).
The VoIP mode of operation can include external SIP trunk, IP trunks between customer systems and or H.323 IP
telephones for users. In either case the following factors must be considered:
· The IP Office control unit must be fitted with voice compression channels 46 . These channels are used whenever an
IP device (trunk or extension) needs to communicate with a non-IP device (trunk or extension) or a device that
uses a different codec.
· A network assessment is a mandatory requirement for all systems using VoIP. For support issues with VoIP, Avaya
may request access to the network assessment results and may refuse support if those are not available or
satisfactory.
A network assessment would include a determination of the following:
· A network audit to review existing equipment and evaluate its capabilities, including its ability to meet both current
and planned voice and data needs.
· A determination of network objectives, including the dominant traffic type, choice of technologies, and setting voice
quality objectives.
· The assessment should leave you confident that the implemented network will have the capacity for the foreseen
data and voice traffic, and can support H.323, DHCP, TFTP and jitter buffers in H.323 applications.
· An outline of the expected network assessment targets is:
Test
Minimum Assessment Target
Latency
Less than 150ms.
Packet Loss
Less than 3%.
Duration
Monitor statistics once every minute for a full week.
IP Office Standard Version Installation
IP Office 7.0
Page 45
15-601042 Issue 23e (16 March 2011)
1.11.1 Voice Compression Channels
Calls to and from IP devices can require conversion to the audio codec format being used by the IP device. For IP Office
systems this conversion is done by voice compression channels. These support the common IP audio codecs G711, G723
and G729a.
For IP400 control units channels can be added by fitting IP400 Voice Compression Modules (VCMs) 245 . For the IP500
control units, channels can be added using IP500 VCM cards 216 , IP500 Combination Cards 210 and or IP400 Voice
Compression Modules 245 .
The voice compression channels are used as follows:
Call Type
Voice Compression Channel Usage
IP Device to Non-IP
Device
These calls require a voice compression channel for the duration of the call. If no channel is
available, busy indication is returned to the caller.
IP Device to IP Device
Call progress tones (for example dial tone, secondary dial tone, etc) do not require voice
compression channels with the following exceptions:
· Short code confirmation, ARS camp on and account code entry tones require a voice
compression channel.
· Devices using G723 require a voice compression channel for all tones except call
waiting.
When a call is connected:
· If the IP devices use the same audio codec no voice compression channel is used.
· If the devices use differing audio codecs, a voice compression channel is required for
each.
Non-IP Device to NonIP Device
No voice compression channels are required.
Music on Hold
This is provided from the IP Office's TDM bus and therefore requires a voice compression
channel when played to an IP device.
Conference Resources
and IP Devices
Conferencing resources are managed by the conference chip which is on the IP Office's TDM
bus. Therefore, a voice compression channel is required for each IP device involved in a
conference. This includes services that use conference resources such as call listen, intrusion,
call recording and silent monitoring.
Page Calls to IP Device
IP Office 4.0 and higher only uses G729a for page calls, therefore only requiring one channel
but also only supporting pages to G729a capable devices.
Voicemail Services and
IP Devices
Calls to the IP Office voicemail servers are treated as data calls from the TDM bus. Therefore
calls from an IP device to voicemail require a voice compression channel.
Fax Calls
These are voice calls but with a slightly wider frequency range than spoken voice calls. IP
Office only supports fax across IP between IP Office systems with the Fax Transport option
selected. It does not currently support T38.
T38 Fax Calls
IP Office 5.0+ supports T38 fax on SIP trunks and SIP extensions. Each T38 fax call uses a
VCM channel.
Within a Small Community Network, a T38 fax call can be converted to a call across an H323
SCN lines using the IP Office Fax Transport Support protocol. This conversion uses 2 VCM
channels.
In order use T38 Fax connection, the Equipment Classification of an analog extension
connected to a fax machine can be set Fax Machine. Additionally, a new short code feature
Dial Fax is available.
Note: T3 IP devices must be configured to 20ms packet size for the above conditions to apply. If left configured for 10ms
packet size, a voice compression channel is needed for all tones and for non-direct media calls.
Measuring Channel Usage
The IP Office System Status Application can be used to display voice compression channel usage. Within the Resources
section it displays the number of channel in use. It also displays how often there have been insufficient channels available
and the last time such an event occurred.
The IP500 VCM cards, the level of channel usage is also indicated by the LEDs (1 to 8) on the front of the IP500 VCM card
216 .
IP Office Standard Version Installation
IP Office 7.0
Page 46
15-601042 Issue 23e (16 March 2011)
System Overview: VoIP
1.12 Supported Country Locales
When a new or defaulted system's configuration is first opened in Manager, the value set in the Locale field should always
be checked and changed if necessary. The system's Locale sets factors such as the default ringing patterns and caller
display settings. The locale also controls the language that a voicemail server will use for prompts.
The locales supported in IP Office Essential Edition - Quick Version and IP Office Standard Version modes are:
· Argentina
· France
· Netherlands
· South Africa
· Australia
· Germany
· New Zealand
· Spain
· Bahrain
· Greece
· Norway
· Sweden
· Belgium
· Hong Kong
· Oman
· Switzerland
· Brazil
· Hungary
· Pakistan
· Taiwan
· Canada
· Iceland
· Peru
· Turkey
· Chile
· India
· Poland
· United Arab Emirates
· China
· Italy
· Portugal
· United Kingdom
· Colombia
· Korea
· Qatar
· United States
· Denmark
· Kuwait
· Russia
· Venezuela
· Egypt
· Mexico
· Saudi Arabia
· Finland
· Morocco
· Singapore
The locales supported in IP Office Essential Edition - Norstar Version mode are:
· Bahrain
· Morocco
· Qatar
· Turkey
· Egypt
· Oman
· Saudi Arabia
· United Arab Emirates.
· Kuwait
· Pakistan
· South Africa
IP Office Standard Version Installation
IP Office 7.0
Page 47
15-601042 Issue 23e (16 March 2011)
1.13 IP Office Software Applications
The IP Office applications are available on a number of DVDs. These can be ordered at a nominal cost to cover order
processing and delivery. Separate installation packages for IP Office applications can also be downloaded from the Avaya
support website at http://support.avaya.com.
Title
Discs Description
IP Office Release 7.0 Admin and
User DVD Set
2
SAP Code
These DVDs contain installation packages for all the main IP
Office administration and user applications. They also contain
documentation for IP Office.
700500928
· DVD 1: Contains the IP Office Administrator
Applications suite, IP Office Documentation, IP Office
User Applications, IP Office Voicemail Pro.
· DVD 2: Contains the Customer Call Reporter,
ContactStore for IP Office and one-X Portal for IP
Office applications.
Voicemail Pro ScanSoft TTS DVD
Set
2
Contains text to speech engines for use with Voicemail Pro's
TTS functions. Supports the same languages as Voicemail Pro
pre-recorded prompts except Hungarian.
IP Office Application Server DVD
Set
2
Install DVD for Voicemail Pro and one-X Portal for IP Office
applications as a Linux based server. The second DVD
contains open source material used for the first DVD.
–
700501420
· It is acceptable to make copies of the Avaya IP Office DVDs listed above. However the content must remain intact,
unaltered and without change or addition. Avaya does not accept any liability and responsibility for damage or
problems arising from the use of such copies.
Programming Applications
The following applications are used to program and maintain an IP Office system. Typically they run on a PC connected to
the IP Office system via its LAN interface. These applications are all provided on the IP Office Administrator Applications
DVD and don't require any licenses.
Due to the nature of the applications, if installed on a PC at the customer site, this should be a secure PC or the PC of a
trusted user. If a voicemail server PC is also being installed with the IP Office system, the same PC can be used for the
programming and maintenance applications.
For maintainers, these applications can also be run remotely if a route for data connections to the customer's IP Office
exists from the maintainer's location.
· IP Office Manager 355
This tool is used to access all parts of the IP Office configuration. Different levels of access can be defined to control
which parts of the configuration the Manager user can view and alter. Manager is also used to upgrade the software
files used by an IP Office system.
· System Status Application 361
This application can be used to inspect the current status of IP Office lines and extensions and to view records of
recent alarms and events. It runs as a Java application.
· SNMP MIBs 139
Not an application as such. Using IP Office SNMP MIB files the status of the IP Office system to be monitored by
3rd-party SNMP applications such as Castlerock and HP OpenView. When configured for SNMP operation, the IP
Office can also send alerts for potential problems. IP Office systems also support the sending of the same alerts to
SMTP email or Syslog addresses.
· The alarms configurable for output via SNMP can also be output to SMTP email and or Syslog.
· The use of SNMP only supported with IP Office Standard Version mode systems, it is not supported with IP
Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office
Essential Edition - Quick Version mode systems.
· Monitor (SysMon) 356
Monitor is a tool that can show a trace of all activity on the IP Office system in detail. As a consequence,
interpretation of Monitor traces requires a high-level of data and telephony protocol knowledge. Despite that
however, all IP Office installers and maintainers need to understand how to run Monitor when necessary as Avaya
may request copies of Monitor traces to resolve support issues.
IP Office Standard Version Installation
IP Office 7.0
Page 48
15-601042 Issue 23e (16 March 2011)
System Overview: IP Office Software Applications
User Applications
The IP Office supports a number of applications that operate in parallel with users telephones. These applications are
installed from the IP Office Applications DVD. The one-X Portal for IP Office server can also be installed as part of the IP
Office Application DVD installation.
Some of them require licenses to be entered into the IP Office system's configuration to enable features or to set the
number of simultaneous users.
These applications are supported in IP Office Standard Version mode. They are not supported in IP Office Essential Edition
- PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential Edition - Quick Version modes.
· one-X Portal for IP Office 357
This application is installed on a server PC connected to the IP Office. Users can access the one-X portal from their
own PC using a web browser. The application allows the user to control their phones, access voicemail messages,
call logs and phone directories.
· Phone Manager 358
Phone Manager allows a user to control and monitor their phone through their PC. For Avaya phones that support
handsfree operation, Phone Manager can be used to make and answer calls. During use, Phone Manager records
details of calls made, answered and missed. It can also be configured to show the status of other users on the
system. Phone Manager also allows the user to access and change many of the setting stored in the IP Office
configuration that relate to their own phone operation, for example their forwarding destination numbers. Phone
Manager software can operate in several modes:
· Phone Manager Lite 358
The default mode of Phone Manager. Requires no license, this application can be installed for any IP Office
user.
· Phone Manager Pro 358
Users configured for Phone Manager Pro are able to access a range of additional features. Phone Manager Pro
requires entry of licenses into the IP Office system. The licenses also control the number of simultaneous Phone
Manager Pro users. The user's Phone Manager software then automatically changes from Lite mode to
Professional Edition mode.
· Phone Manager Pro PC Softphone 358
This is a PC softphone mode of Phone Manager operation. The user acts as a VoIP extension, making calls
through the speaker and microphone of their PC. This mode requires further licenses in addition to the Phone
Manager Pro licenses.
· SoftConsole 360
This is a licensed application. It is intended for telephone system operators or receptionists. It displays details of
calls and allows them to quickly see the status of the callers required destination and transfer the call. The
SoftConsole user is able to access a range of details about the status of users and groups on the IP Office system.
Up to 4 simultaneous SoftConsole users can be licensed.
For systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP
Office Essential Edition - Quick Version modes, the following is supported:
· TAPILink Lite 362
The Microsoft Telephony Application Program Interface (TAPI) allows TAPI compliant applications to interact with IP
Office phones by installing an IP Office TAPI driver. TAPILink Lite does not require any licenses entered into the IP
Office system's configuration. It allows TAPI compliant applications such as Outlook to make and answer calls. The
speech part of the calls is still via the user's physical phone.
Voicemail Applications
The IP Office supports a range of applications for the recording and playing of voicemail messages.
· Embedded Voicemail 244
This application is supported on all IP Office Release 6 systems. Embedded Voicemail supports basic voicemail
mailbox operation, simple auto-attendants and hunt group announcements. For IP500 and IP500v2 controls units,
embedded voicemail is provided by the Avaya SD card fitted by default.
· Voicemail Pro 363
This voicemail application runs on a server PC connected to the IP Office. It requires various licenses entered into
the IP Office configuration to control the features it offers and the number of simultaneous connections. The
operation of Voicemail Pro can be customized to provide special services.
· ContactStore for IP Office 353
Voicemail Pro can be used for manual and automatic call recording. Those recording are placed into mailboxes.
Contact Store allows those recordings to be redirected into a database on the ContactStore PC. This allows
recordings to be archived and searched separately from mailbox messages. This application requires entry of a
license into the IP Office configuration.
IP Office Standard Version Installation
IP Office 7.0
Page 49
15-601042 Issue 23e (16 March 2011)
Call Logging Applications
A wide range of 3rd -party applications exist to provide call logging and accounting for telephone systems. To support
these the IP Office provides an SMDR output.
· SMDR Output
For IP Office Release 5.0 and higher, the IP Office control unit directly output SMDR records to a specified IP
address.
Call Center Application
· Customer Call Reporter 354
This application is installed on a server PC connected to the IP Office. Users access the application from their PC
using a web browser. The application obtains data about the calls handled by CCR agents and groups from the IP
Office system and stores that data in an MS-SQL database. It can support up to 150 agents and 75 supervisors.
CTI Applications
· TAPILink Pro
Using the same software as TAPILink Lite, TAPILink Pro provides all of the features and functionality of TAPILink
Lite, but additionally provides third party CTI operation. This means that a single server can control and monitor
any number of telephone devices. This requires entry of a CTI Link Pro license. TAPILink Pro also provides the
ability to monitor and control groups. This allows an application to be notified when a call enters a queue, and can
also redirect it to another location.
· TAPI WAV driver
Provides software-based support for voice processing. Purchasing the CTI Link Pro RFA license key also enables 4
ports of voice processing; additional ports can be purchased in 4 port increments. The TAPI-WAV driver is for use
with TAPI 2.1 only; for TAPI 3.0, IP Office supports the Media Service Provider (MSP) interface, defined by Microsoft
in TAPI 3.0.
· DevLink Pro
Provides a real-time event stream in addition to the SMDR interface provided in IP Office SMDR (see below). The
real-time event stream takes the form of a call record, which is issued whenever the state of any endpoint of a call
changes (typically there are two endpoints on a call, but for some circumstances, such as conference calls, intruded
calls there may be more).
IP Office Standard Version Installation
IP Office 7.0
Page 50
15-601042 Issue 23e (16 March 2011)
System Overview: IP Office Software Applications
1.14 Training
Avaya University provides a wide range of training courses for IP Office and its associated applications. This includes
courses necessary for IP Office resellers to become Avaya Authorized Channel Partners and for individuals to achieve IP
Office certification.
Details of courses can be found on the Avaya University web site (http://www.avaya-learning.com). The site can be used
to check course availability and to book course. It also includes on-line courses and on-line course assessments. The site
requires users to setup a user name and password in order to track their personal training record.
1.15 Web Sites
Information to support the IP Office can be found on a number of web sites.
· Avaya (http://www.avaya.com)
The official web site for Avaya. The front page also provides access to individual Avaya web sites for different
countries.
· Avaya Enterprise Portal (http://partner.avaya.com)
This is the official web site for all Avaya Business Partners. The site requires registration for a user name and
password. Once accessed, the site portal can be individually customized for what products and information types
you wish to see and to be notified about by email.
· Avaya Support (http://support.avaya.com)
Contains documentation and other support materials for Avaya products including IP Office. Copies of the IP Office
CD images are available from this site and updated core software .bin files.
· Avaya IP Office Knowledge Base (http://marketingtools.avaya.com/knowledgebase)
Access to an on-line regularly updated version of the IP Office Knowledge Base.
· Avaya University (http://www.avaya-learning.com)
This site provides access to the full range of Avaya training courses. That includes both on-line courses, course
assessments and access to details of classroom based courses. The site requires users to register in order to
provide the user with access to details of their training record.
· Avaya Community (http://www.aucommunity.com)
This is the official discussion forum for Avaya product users. However it does not include any separate area for
discussion of IP Office issues.
· Other Non-Avaya Web Sites
A number of third-party web forums exist that discuss IP Office. These can act as useful source of information
about how the IP Office is used. Some of these forums require you to be a member and to register. These are not
official Avaya forums and their content is not monitored or sanctioned by Avaya.
· Tek-Tips (http://www.tek-tips.com)
· IP Office Info (http://www.ipofficeinfo.com)
· Yahoo Groups (http://groups.yahoo.com/group/ipoffice)
· PBX Tech (http://www.pbxtech.info/forumdisplay.php?f=8)
IP Office Standard Version Installation
IP Office 7.0
Page 51
15-601042 Issue 23e (16 March 2011)
1.16 Emergency and Power Failure Ports
IP Office systems can provide 2 types of analog extension power failure ports. These are:
Type
Description
Provided By:
Switching Power
Failure Ports
During normal IP Office operation these ports
can be used for normal analog phone
connection.
· IP500 Analog Phone 8 Card
When an IP500 Analog Phone 8 base card is
fitted with an IP500 Analog Trunk daughter
card, during power failure extension port 8 is
connected to analog trunk port 12.
During power failure the port is directly
connected to an analog trunk port.
· IP500 ATM Combination Card
On this card, during power failure, extension
port 8 is connected to analog trunk port 12.
Emergency Only Power During normal IP Office operation these ports
Failure Ports
cannot be used.
During power failure the port is directly
connected to an analog trunk port.
· IP500 Analog Trunk Daughter Card
Regardless of the IP500 card hosting it,
during power failure pins 4 and 5 of port 12
are connected to pins 7 and 8.
· IP400 ATM16 External Expansion
Module
This external expansion module has two
ports, PF1 and PF2, on its rear. During
power fail conditions, PF1 is internally
connected to ANALOG port 1 on the module,
PF2 is internally connected to ANALOG port
2 on the same module.
· IP500 ETR6 Card
On this card, during normal operation
extension ports 7 and 8 are not useable.
However, if the card is fitted with an IP500
Analog Trunk daughter card, during power
failure extension ports 7 and 8 are
connected to analog trunk port 12.
In all cases these only work with loop-start analog trunks. Any phones connected to these ports should be clearly labeled
as power fail extensions in accordance with the appropriate national and local regulatory requirements.
IP Office Standard Version Installation
IP Office 7.0
Page 52
15-601042 Issue 23e (16 March 2011)
Chapter 2.
Installation Requirements
IP Office Standard Version Installation
IP Office 7.0
Page 53
15-601042 Issue 23e (16 March 2011)
2. Installation Requirements
2.1 Environmental Requirements
The planned location must meet the following requirements. If being installed into a rack system, these are requirements
for within the rack:
1. o Temperature: 0°C to 40°C / 32°F to 104°F.
2. o Humidity: 10% to 95% non-condensing.
3. o Check there are no flammable materials in the area.
4. o Check there is no possibility of flooding.
5. o Check that no other machinery or equipment needs to be moved first.
6. o Check that it is not an excessively dusty atmosphere.
7. o Check that the area is unlikely to suffer rapid changes in temperature and humidity.
8. o Check for the proximity of strong magnetic fields, sources of radio frequency and other electrical interference.
9. o Check there are no corrosive chemicals or gasses.
10.o Check there is no excessive vibration or potential of excessive vibration, especially of any mounting surface.
11.o Check that where telephones are installed in another building, that the appropriate protectors and protective
grounds are fitted (see Out of Building Telephone Installation 39 ).
12.o Check there is suitable lighting for installation, system programming and future maintenance.
13.o Check that there is sufficient working space for installation and future maintenance.
14.o Ensure that likely activities near the system will not cause any problems, e.g. access to and maintenance of any
other equipment in the area.
15.o Where ventilation holes are present on any of the IP Office units, those holes should not be covered or blocked.
16.o The surface must be flat horizontal for free-standing or rack mounted installations.
Wall Mounting
In additional to the requirements above, the following are applicable to IP Office units that support wall mounting.
1. Units must only be mounted onto permanent wall surfaces.
2. The surface must be vertical and flat.
3. Orientation of the unit must be as shown in the section on IP500 Wall Mounting
82
.
4. The appropriate Avaya wall mounting kits must be used.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual.
IP Office Standard Version Installation
IP Office 7.0
Page 54
15-601042 Issue 23e (16 March 2011)
Installation Requirements: Environmental Requirements
2.2 Space Requirements
IP Office control units and modules are designed to be installed either in a free-standing stack or into a 19" rack system.
Rack installation requires a rack mounting kit 40 for each control unit and expansion module.
· Cable Clearance
Clearance must be provided at the front and rear of all modules for cable access and feature key dongle connection.
· On IP400 systems, allow a minimum clearance of 75mm (3 inches).
· On IP500 and IP500v2 systems allow a minimum clearance of 90mm (3.5 inches).
· Additional Clearance
Care should be taken to ensure that the positioning of the modules does not interrupt air flow and other factors that
may affect environmental requirements 54 . This is especially important on IP500 and IP500v2 control units which
have ventilation slots at the side.
· Cable Access
Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing
of the power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment
near a socket outlet.
IP Office Standard Version Installation
IP Office 7.0
Page 55
15-601042 Issue 23e (16 March 2011)
2.2.1 IP500 and IP500v2 Control Units
The ventilation slots on the rear and sides should not be covered or blocked.
2.2.2 External Expansion Modules
The dimensions below are applicable to all IP Office external expansion modules.
IP Office Standard Version Installation
IP Office 7.0
Page 56
15-601042 Issue 23e (16 March 2011)
Installation Requirements: Space Requirements
2.2.3 Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Standard Version Installation
IP Office 7.0
Page 57
15-601042 Issue 23e (16 March 2011)
Wall Mounting Kit V2
Wall Mounting Kit V1
IP Office Standard Version Installation
IP Office 7.0
Page 58
15-601042 Issue 23e (16 March 2011)
Installation Requirements: Space Requirements
2.2.4 Rack Space Requirements
All IP Office control units and external expansion modules can be rack mounted into standard 19" rack systems. Each unit
requires a 2U slot space within the rack. Rack mounting requires an IP400 or IP500 rack mounting kit for each control unit
and external expansion module.
Where IP Office systems are being rack mounted, the effect of conditions within the rack cabinet must be considered. For
example the rack temperature may be above the room temperature and airflow within the rack will be restricted. The
environmental requirements 54 for the individual IP Office units are still applicable inside the rack cabinet.
IP500 Rack Mounting Kit
· IP500 Rack Mounting Kit (SAP 700429202)
This kit contains all the components required for the rack mounting of
a single IP500v2 control unit, IP500 control unit or IP500 external
expansion module. This includes screws for fixing of the brackets to
the module, bolts for securing the module in the rack and cable tidy
brackets.
IP400 Rack Mounting Kit
· IP400 Rack Mounting Kit (SAP 700210800)
This kit contains all the components required for the rack mounting of
a single control unit or expansion module. This includes screws for
fixing of the brackets to the module and bolts for securing the module
in the rack.
Barrier Box Rack Mounting Kit
· Barrier Box Rack Mounting Kit (SAP 700293905)
Barrier boxes must be used for out-of-building analog phone
extensions 39 . This bracket allows up to 8 IP Office barrier boxes to
be rack mounted and simplifies the number of connections to the
protective ground point in the rack. This kit must be used when more
than 3 barrier boxes are in use and supports a maximum of 16
barrier boxes for a single external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 59
15-601042 Issue 23e (16 March 2011)
Rack Module Positioning
The integral expansion ports on a control unit are located on the rear of the unit. For IP500 and IP500v2 control units, an
additional 4 expansion ports can be added to the front of the control unit by installing an IP500 4-Port Expansion card.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
IP Office Standard Version Installation
IP Office 7.0
Page 60
15-601042 Issue 23e (16 March 2011)
Chapter 3.
IP Office Administration
Software
IP Office Standard Version Installation
IP Office 7.0
Page 61
15-601042 Issue 23e (16 March 2011)
3. IP Office Administration Software
In order to install an IP Office system you must be familiar with using the following IP Office applications. They must be
available on your installation PC.
·
Manager
IP Office Manager is used to access all parts of the IP Office configuration. Different levels of access can be defined
to control which parts of the configuration Manager user can view and alter. Manager is also used to upgrade the
software files used by an IP Office system.
·
System Status
The IP Office System Status application (SSA) is a reporting tool that provides a wide range of information about
the current status of an IP Office system. Its can report the available resources and components within the system
and details of calls in progress. Details of the number of alarms are recorded and the time date of the most recent
alarms. When required for diagnostics escalation, SSA is able to take a snap shot image of the IP Office system's
status including a copy of its current configuration. Use of SSA requires an IP Office service user name and
password that has been configured for System Status access in the IP Office's security settings.
·
Monitor
IP Office Monitor (also known as System Monitor) is a tool that can show all activity on the IP Office system in great
detail. As a consequence, interpretation of Monitor traces requires a high-level of data and telephony protocol
knowledge. However, all IP Office installers and maintainers must understand how to run Monitor when necessary
as Avaya may request copies of Monitor traces to resolve support issues.
· Phone Based Administration
For systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version
or IP Office Essential Edition - Quick Version modes, many features can be administered using phone based
administration from either of the first two extensions in the system. This option is not used for IP Office Standard
Version mode.
IP Office Standard Version Installation
IP Office 7.0
Page 62
15-601042 Issue 23e (16 March 2011)
IP Office Administration Software:
3.1 Installing the Admin Applications
The IP Office Administration suite consists of a number of applications for IP Office installers and
maintainers.
· o System Monitor - Install
· o Manager - Install
· o System Status Application - Install
· o Call Status - Optional
This software is not supported with IP Office Release 7.0 systems. It is provided only for
the maintenance of older systems.
Requirements
· o IP Office Release 7.0 User/Admin DVD Set (2) (700500928)
Alternatively the IP Office Administrator Applications suite can be downloaded from Avaya's support website (
http://support.avaya.com).
· o Windows PC Requirements
This should meet the requirements of the administrator applications being installed. The specification below are the
minimum requirements for IP Office Manager. If other applications are to be installed on the PC then their individual
requirements should also be meet.
Requirement
Minimum
Recommended
Processor
600MHz Pentium or AMD Opteron, AMD
Athlon64, AMD Athlon XP.
800MHz Pentium or AMD Opteron, AMD
Athlon64, AMD Athlon XP.
RAM
128MB
256MB
HD Space
1GB - 800MB for .NET2, 200MB for Manager.
1.4GB - 800MB for .NET2, 600MB for the full
IP Office Admin suite.
Display
800 x 600 - 256 Colors
1024 x 768 - 16-bit High Color
Operating
System
Supported on Windows XP Pro, Windows Vista, Windows 7, Windows 2003 and Windows
2008.
· 32-bit and 64-bit versions are supported.
· Vista support is only on Business, Enterprise and Ultimate versions.
· Windows 7 support is only on Professional, Enterprise and Ultimate versions.
IP Office Standard Version Installation
IP Office 7.0
Page 63
15-601042 Issue 23e (16 March 2011)
Installing the IP Office Admin Applications
1. Using the Add or Remove Programs option in the Windows Control Panel, check that the PC does not already
have a version of the IP Office Admin suite installed.
· If 'yes' and the suite is a pre-IP Office 3.2 version, remove the existing IP Office Admin suite via Add/Remove
Programs.
· If the existing suite is IP Office 3.2 or higher, it is possible to upgrade without removing the previous
installation. However, if the system already has a USB Feature Key, the key should be removed prior to
upgrading and then reinserted and the PC restarted.
2. Insert the IP Office Administrator Applications DVD. Select the option for the IP Office Administration Suit. A folder
window will display the installation files for the administration suite.
3. Double-click on setup.exe.
4. Select the language you want to use for the installation process. This does not affect the language used by Manager
when running. Click Next >.
5. Select who should be able to run the Admin Suite applications. Click Next >.
6. If required select the destination to which the applications should be installed. We recommend that you accept the
default destination. Click Next >.
7. The next screen is used to select which applications in the suite should be installed. Clicking on each will display a
description of the application. Click on the
next to each application to change the installation selection. When you
have selected the installations required, click Next >.
8. Ensure that at minimum System Monitor and Manager are selected. Click Next >.
9. Click Install.
10.Installation of Windows .Net2 components may be required. If dialogs for this appear, follow the prompts to
install .Net.
11.If requested, reboot the PC.
IP Office Standard Version Installation
IP Office 7.0
Page 64
15-601042 Issue 23e (16 March 2011)
IP Office Administration Software: Installing the Admin Applications
3.2 Installer PC Connection
During installation it is recommended that the IP Office control unit is started
without it being connected to any network. That ensure that the IP Office
defaults to a known set of IP address settings.
If the IP Office is started connected to a network with a DHCP server. The
programming PC will need to be connected to the same network as either a
DHCP client or with an IP address valid for that network.
This section covers connecting your installation PC directly to the IP Office
control unit.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
63 .
· o LAN Cable
Direct Connection to a Defaulted IP Office Control Unit
1. The default address for an IP Office control unit LAN port is 192.168.42.1/255.255.255.0. To directly connect a PC,
change the TCP/IP properties for the PCs LAN port to the following:
Fixed IP address
192.168.42.203
Subnet mask
255.255.255.0
Default gateway
192.168.42.1.
· While setting the PC to be a DHCP client could be used, this is not recommended for performing more
advanced functions such as firmware upgrades.
2. Connect the LAN cable from the PCs LAN port the LAN or LAN1 port on the IP Office control unit.
3. Check that the orange LED lamp on the IP Office LAN port is on. The green LED may also be flickering as it indicates
traffic across the LAN connection.
4. To test the connection before running Manager or System Status Application:
· Select Start | Run and enter cmd.
· In the command window that appears enter ping 192.168.42.1. The results should show a number of ping
replies from the IP Office. This confirms basic communication between the Manager PC and the IP Office.
· If there are no ping replies enter ipconfig. The results should list the IP address settings of the Manager PC as
required above. If they do enter exit and check the cable connection.
5. You can now start Manager
66
, System Status
IP Office Standard Version Installation
IP Office 7.0
67
or System Monitor
68
.
Page 65
15-601042 Issue 23e (16 March 2011)
3.3 Starting Manager
IP Office Manager is used to access all parts of the IP Office configuration.
Manager can also be used to upgrade the software files used by an IP Office
system.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
63 .
· o LAN Cable
1. Select Start | Programs | IP Office | Manager.
2. If the PC has firewall software installed, you may be prompted as to whether you want to allow this program to
access the network. Select Yes or OK.
3. Select File | Open Configuration from the menu bar.
4. The Select IP Office window appears. After a few seconds it should list the IP Office control unit. The default name
used for a newly installed IP Office control unit is its MAC address.
· If the system required was not found, the address used for the search can be changed. Enter or select the
required address in the Unit/Broadcast Address field and then click Refresh to perform a new search.
5. Click the check the box next to the system and then click OK.
6. The name and password request is displayed. The name and password must match one of those setup through the
security settings. For a IP Office Standard Version mode system, the default name and password for full
configuration settings access are Administrator and Administrator. For a IP Office Essential Edition - PARTNER®
Version, IP Office Essential Edition - Norstar Version or IP Office Essential Edition - Quick Version mode system, the
default name and password for configuration access are Administrator and password.
IP Office Standard Version Installation
IP Office 7.0
Page 66
15-601042 Issue 23e (16 March 2011)
IP Office Administration Software: Starting Manager
3.4 Starting System Status
The IP Office System Status application (SSA) is a reporting tool that provides a
wide range of information about the current status of an IP Office system. Its can
report the available resources and components within the system and details of
calls in progress. Details of the number of alarms are recorded and the time date
of the most recent alarms.
When required for diagnostics escalation, SSA is able to take a snap shot image of
the IP Office system's status including a copy of its current configuration. Use of
SSA requires an IP Office service user name and password that has been
configured for System Status access in the IP Office's security settings.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
63 .
· o LAN Cable
1. There are several methods that can be used to start the IP Office System Status application.
· On a PC where System Status has been installed, select Start | Programs | IP Office | System Status.
· If Manager is also installed and is running, select File | Advanced | System Status.
· For IP500v2 controls units, start a web browse and enter the IP address of the control unit. Select the link for
the System Status Application.
2. Once System Status has started, it will request the details of the IP Office system to which you want it to connect.
· Control Unit IP Address
Enter the IP address of the IP Office control units LAN interface or use the drop down to select a previously
used address.
· Services Base TCP Port
This should match the Services Base TCP Port setting of the IP Office system, set in that systems security
settings. The default is 50804.
· Local IP Address
If the PC has more than one IP address assigned to its network card or multiple network cards, the address to
use can be selected if necessary. This allows System Status to be run on a PC that is already running an SSI
connection to the IP Office for the IP Office Customer Call Reporter application.
· User Name/Password
Enter a user name and password that has been provided for System Status usage. By default this is the same
as the user name and password used with IP Office Manager. This must be the name of an IP Office service
user name that has been configured for system status access in the IP Office's security settings.
· Auto Reconnect
If selected, System Status will attempt to reconnect using the same settings if connection to the IP Office is
lost.
3. Enter the required details for the IP Office and click Logon.
IP Office Standard Version Installation
IP Office 7.0
Page 67
15-601042 Issue 23e (16 March 2011)
3.5 Starting Monitor
IP Office Monitor (also know as System Monitor) is a tool that can show all activity
on the IP Office system in great detail. As a consequence, interpretation of
Monitor traces requires a high-level of data and telephony protocol knowledge.
However, all IP Office installers and maintainers must understand how to run
Monitor when necessary as Avaya may request copies of Monitor traces to resolve
support issues.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
63 .
· o LAN Cable
1. Select Start | Programs | IP Office | Monitor.
2. If System Monitor has been run before it will attempt to connect with the system which it monitored previously. If
otherwise or you want to monitor a different system use the steps below.
3. Select File | Select Unit.
4. Enter the IP Office IP address and password of the IP Office Control Unit you want to monitor.
· Using IP Office Manager it is possible to set a specific System Monitor Password for System Monitor access
to an IP Office system. If the IP Office doesn't have a System Monitor Password set, System Monitor uses
the IP Office's System Password. The System Monitor Password and System Password are both set within the
IP Office system security settings.
· For an IP Office system, ensure that the Control Unit Type is set to IP Office.
5. Click OK.
3.6 Phone Based Administration
For systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version or IP
Office Essential Edition - Quick Version modes, many features can be administered using phone based administration. This
option is not used for IP Office Standard Version mode.
Some settings cannot be changed through phone based administration; for example IP address and SIP trunk settings.
Those settings are only used in conjunction with network systems for which it is assumed that IP Office Manager will be
used for system configuration.
Phone based administration is only possible using either of the first two extension in the system. The phone connected at
those positions also needs to be capable of being used for phone based admin.
· Supported phones are: ETR 18D, ETR 34D, M7310, M7310N, M7324, M7324N, T7316E, T7316, 1408 and 1416
phones.
· The card fitted into Slot 1 of the control unit must be the correct type to support the phones.
· For details, refer to the Phone Based Administration manual.
IP Office Standard Version Installation
IP Office 7.0
Page 68
15-601042 Issue 23e (16 March 2011)
Chapter 4.
IP500v2 Installation
IP Office Standard Version Installation
IP Office 7.0
Page 69
15-601042 Issue 23e (16 March 2011)
4. IP500v2 Installation
This installation process is a simple outline as installation requirements and processes will vary.
· In this process, all the IP Office hardware components are installed and connected without being switched on until
the end of the process. The control unit will then upgrade all the connected components, including phones, to the
appropriate level of firmware.
· Also when switched on, the system is not connected to the customers data network. This ensures that the control
unit will default to known default IP address settings (unless you have pre-loaded the System SD card with a
configuration file with different settings).
· Tools and Parts Required 71
Check that you have the tools and additional parts required.
· Documentation 72
Ensure that you have obtained and read all the relevant documentation.
· Unpacking 73
Check that all the required equipment has been delivered and that there is no damage.
· SD Card Preparation 74
Upgrade and pre-load the System SD card with a configuration and other files in order to speed up installation.
· Install the Base Cards 78
Attach any trunk daughter cards and IP400 legacy cards to the IP500 base cards. Insert the cards into the control
unit.
· Wall Mounting 82
If wall mounting, attach the brackets and fit the unit to the wall.
· Rack Mounting 86
If rack mounting, attach the brackets and fit the control unit into the rack.
· Connect External Expansion Modules 88
Connect the external expansions modules to the control unit.
· Grounding 90
Attach required ground cables to the control unit and external expansion modules.
· LAN Network Connections 91
Attach the IP Office control unit and a PC with IP Office Manager to the LAN network.
· Starting the System 92
Insert the System SD card and power up the system.
· Changing the System to IP Office Standard Version Mode 95
IP500v2 systems installed in IP Office Essential Edition - Quick Version mode can be changed to operate in IP Office
Standard Version mode.
· Connecting Phones 96
Connect the Avaya digital phones.
IP Office Standard Version Installation
IP Office 7.0
Page 70
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation:
4.1 Tools and Equipment Required
The following is a general summary of the tools required. Additional tools and equipment will be
required for wall and or rack mounting and to fashion ground cable connections suitable to local
requirements.
· Tools Required
· o 5mm Flat-blade screwdriver.
· o Crosshead screwdriver.
· o Anti-static wrist strap and ground point.
· o RJ45-RJ45 Ethernet LAN Cable.
· o M4 Cross-Head Screwdriver.
· o Tools suitable for crimping a cable spade.
· o If wall mounting, drills and tools for wall mounting fixtures.
· Additional Parts Required
In addition to orderable IP Office equipment, the following items will be required.
· o 14AWG Solid copper wire for ground connection of control units and expansion modules.
· o Cable sleeve matching local regulator requirements for ground wires. Typically green for a functional ground
and green/yellow for a protective ground.
· o If wall mounting, additional fixtures and fittings suitable for the wall type and mounting kit being used.
· o Cable ties and labels for tidying and identifying cables.
· PC Requirements
IP Office Essential Edition - PARTNER® VersionIP Office Essential Edition - Norstar VersionIP Office Essential Edition
- Quick Version
1. o Windows PC with IP Office Admin suite installed
63
and RJ45 Ethernet LAN port.
2. o SD Card reader.
IP Office Standard Version Installation
IP Office 7.0
Page 71
15-601042 Issue 23e (16 March 2011)
4.2 Documentation
Ensure that you have read this manual in full before starting installation. Also include the
installation documentation for any other equipment and applications being installed as part
of the IP Office system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
· Partner Version Installation
· Compact DECT Installation.
· one-X Portal for IP Office Installation
· IP DECT R4 Installation.
· 4600/5600 Series IP Phone Installation.
· 3600 Series Wireless IP Installation.
· Embedded Voicemail Installation.
· Phone Manager Installation Manual.
· Voicemail Pro Installation.
· SoftConsole Installation Manual.
· Contact Store Installation.
· SIP Extension Configuration
Information Web Sites
IP Office documentation is available from the following web sites.
· Avaya Support (http://support.avaya.com)
Contains documentation and other support materials for Avaya products including IP Office. Copies of the IP Office
CD images are available from this site and updated core software .bin files.
· Avaya IP Office Knowledge Base (http://marketingtools.avaya.com/knowledgebase)
Access to an on-line regularly updated version of the IP Office Knowledge Base.
IP Office Standard Version Installation
IP Office 7.0
Page 72
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Documentation
4.3 Unpacking
Use the following procedure when unpacking any equipment supplied by
Avaya or an Avaya reseller or distributor.
Information Required
· o Equipment Checklist.
An installation checklist of the parts and equipment ordered for the
installation.
Procedure
1. o Check for Packaging Damage
Before unpacking any equipment, check for any signs of damage that may have occurred during transit. If any
damage exists bring it to the attention of the carrier.
2. o Check the Correct Parts Have Been Delivered
Check all cartons against the packing slip and ensure that you have the correct items. Report any errors or
omissions to the equipment supplier.
3. o Retain All Packaging and Documentation
While unpacking the equipment, retain all the packaging material. Fault returns are accepted only if repackaged in
the original packaging. If performing a staged installation, the original packaging will also assist when repacking
equipment to be moved to the final install site.
4. o Ensure that Anti-Static Protection Measures are Observed
Ensure that anti-static protection measures are observed at all times when handling equipment with exposed
electrical circuit boards.
5. o Check All Parts
Visually inspect each item and check that all the necessary documentation and accessory items have been included.
Report any errors or omissions to the dealer who supplied the equipment.
6. o Check All Documentation
Ensure that you read and retain any documentation included with the equipment.
IP Office Standard Version Installation
IP Office 7.0
Page 73
15-601042 Issue 23e (16 March 2011)
4.4 SD Card Preparation
IP500v2 control units are supplied with no installed firmware or configuration. When first powered up, the control unit will
load and install the necessary firmware from the System SD card installed in it. It will then create a default configuration
matching the cards installed in the control unit and external expansion modules attached to it.
You can perform a number of additional actions prior to installing the System SD card in order to pre configure the IP
Office system.
· Upgrade the Card Firmware
· Add a Configuration File
· Add a License File
74
74
77
· Add Music on Hold Files
77
· Add a 9600 Screen Saver Image File
77
Additional actions that can be performed on SD cards are detailed in the SD Card Management
152
section.
4.4.1 Upgrade the Card Firmware
This command can be used with a read-writeable SD card on the Manager PC. It copies the files and folders used by an
IP500v2 system when starting. It updates the card with the version of those files installed with the IP Office Manager
application. It includes the binary files for the IP500v2 system, external expansion modules and phones. It also includes
the prompt files for embedded voicemail operation.
This process just replaces existing files and adds new files. It does not delete files, so for example, any existing embedded
voicemail messages and greetings are retained. If the card contains dynamic system files such as SMDR records, they are
temporarily backed up by Manager and then restored after the card is recreated.
For the card to be used in an IP500v2 system's System SD slot the card must be Avaya SD Feature Key card. The card
must be correctly formatted, however a reformat of an existing working card is not necessary before using recreate to
update the card contents.
· The source for the files copied to the SD card are the sub-folders of the \Memory Cards folder under Manager's
Working Directory (normally C:\Program Files Avaya\IP Office\Manager). However, if the Working Directory
is changed to a location without an appropriate set of \Memory Cards sub-folders, the required set of files will not
be copied onto the SD card.
1. Once started do not interrupt this process, for example by removing the SD card. This process takes approximately
15 minutes.
2. Insert the SD card into a card reader on the Manager PC.
3. Using IP Office Manager, select File | Advanced | Recreate IP Office SD Card.
4. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection will affect how the IP
Office systems operates when defaulted with this card present in its System SD card slot. .
5. Browse to the card location and click OK.
6. Manager will start creating folders on the SD card and copying the required files into those folders. This process will
take approximately 15 minutes.
7. Do not remove the SD card during the process. Wait until the Manager displays a message.
4.4.2 Adding a Pre-Built Configuration File
IP Office Manager can be used to create an IP Office configuration file 76 . For IP500v2 control units, such a pre-created
IP Office configuration file can be placed on the System SD card. That file will then be used when the IP Office system is
started.
IP Office Standard Version Installation
IP Office 7.0
Page 74
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: SD Card Preparation
1. Using IP Office, create an offline configuration that matches the customer requirements and the equipment that will
be installed in the IP Office.
2. Rename the configuration file config.cfg.
3. Using a card reader, copy the file into the /system/primary folder on the System SD memory card.
IP Office Standard Version Installation
IP Office 7.0
Page 75
15-601042 Issue 23e (16 March 2011)
4.4.3 Creating a Configuration File
IP Office Manager can be used to create a new configuration without connecting to an IP Office system. During the
process, you can specify the locale of the system, what type of trunk cards it uses and what type of control unit and
expansion modules to include.
This allows the creation of a configuration prior to installation of system. The configuration file can be placed onto the
System SD card 74 before it is installed into the system. Otherwise the configuration can be uploaded to the system using
Manager after initial installation of the system.
· The configuration created must match the physical equipment in the IP Office system onto which the configuration
will be loaded. Doing otherwise may cause the IP Office system to reset and experience other problems.
1. Start IP Office Manager with no configuration loaded into Manager
2. Click on Create an Offline Configuration in the simplified view.
3. Select the type of configuration that you want to create. The equipment and settings will be restricted to those
supported in the selected mode.
4. When completed click OK.
5. Manager will create an load the configuration.
6. Edit the configuration to match the customer requirements. This can include importing information from
preprepared CSV files.
7. When completed, select File | Save Configuration As.
IP Office Standard Version Installation
IP Office 7.0
Page 76
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: SD Card Preparation
4.4.4 Adding a License File
For IP500v2 control units, if a licence file called keys.txt is found in the SD card folder which the IP Office uses when it
boots, the IP Office will merge the licenses in that file with its configuration.
The files should be a plain text file (UTF8) containing either:
· A license name and license key separated by a
comma on each line.
· A license key on each line.
Teleworker, uAuToY@9VvVV@VOzIgeegwLXL2sAs1Z5
Mobile Worker, NvWO_iVY5KJpZMNeY89IB1sIj0_QUCDm
Power User, 9IJQW3yuPsbxjGS2XcMa16_J9H8cSeZ9
System Advanced, JAWZaw@YtK37vcnXkqM4mDYDIdSMd9_1
uAuToY@9VvVV@VOzIgeegwLXL2sAs1Z5
NvWO_iVY5KJpZMNeY89IB1sIj0_QUCDm
9IJQW3yuPsbxjGS2XcMa16_J9H8cSeZ9
JAWZaw@YtK37vcnXkqM4mDYDIdSMd9_1
1. Using a card reader, copy the file into the /system/primary folder on the System SD memory card.
4.4.5 Adding a 9600 Series Screen Saver File
When idle, 9600 Series phones can timeout to displaying a screen saver image. A file, 96xxiposs.jpg, is present on the
cards by default.
You can replace this file with your own branded file. The file should be smaller than the screen size on 9600 Series phones
in order to then be moved around the screen.
Phone
Maximum Size
Phone
Maximum Size
Phone
Maximum Size
9620
232 x 69
9621G
350 x 153
9641G
480 x 272
9620L
232 x 69
9630
232 x 140
9650
232 x 140
9620C
232 x 69
9640
232 x 140
9650C
232 x 140
· Color Displays: Color depth is 16 bit. A separate color image will look best.
· Non-Color Displays: Best results are achieved with a single grayscale logo image. 2 levels of grayscale are also
supported.
· To invoke transparent backgrounds with logos, use a background color of 0,255,0 (brightest possible green).
4.4.6 Adding Music on Hold Files
By default the IP Office will use internal music on hold by uploading a music file from the IP Office Manager PC. For
IP500v2 systems, you can load a file onto the System SD card prior to installing it in the IP Office.
The file must be of the following format and must be called holdmusic.wav.
Property
Value
File Type
WAV
Bit Rate
128kbps
Audio sample size
16 bit
Channels
1 (mono)
Audio Sample Rate
8 kHz
Audio Format
PCM
Length
Up to 90 seconds.
1. Rename the music file holdmusic.wav.
2. Using a card reader, copy the file into the /system/primary folder on the System SD memory card.
3. If the IP Office is or will be configured for additional hold music files (up to 3 additional files), copy those files to the
same location. The name of the additional files must match those specified in the IP Office system's configuration.
IP Office Standard Version Installation
IP Office 7.0
Page 77
15-601042 Issue 23e (16 March 2011)
4.5 IP500 Card Installation
The IP500 base cards and trunk daughter cards should be fitted before power
is applied to the control unit. Ensure that cards are inserted in the order that
matches the planned or pre-built configuration.
1. Fitting IP500 Trunk Daughter Cards to the Base Cards.
2. Fitting IP400 Legacy Cards to a Legacy Card Carrier.
3. Installing IP500 Cards into the Control Unit.
·
79
80
81
Warnings
· Correct anti-static protection steps should be taken before handling circuit boards.
· Cards must never be added or removed from the control unit while it has power connected.
· General Notes
· Cards can be fitted in any order into any available slots. The only exception is the IP500 4-Port Expansion card
which can only be installed in right hand slot 4.
· For phone based administration, the card in slot 1 must be able to support ETR 18D, ETR 34D, M7324, M7310,
T7316E, T7316, 1408 or 1416 phones. Phone based administration is not supported in IP Office Standard
Version mode.
· It is recommended that cards are fitted from left to right.
· There are restrictions to the number of supported cards of some types. When such a limit is exceed, the rightmost card of that type will not function.
· Ensure that you use the labels supplied to identify the card fitted into the control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 78
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: IP500 Card Installation
4.5.1 IP500 Daughter Card Preparation
IP500 trunk daughter cards can be fitted to any IP500 base card except the IP500 Legacy Card Carrier. For IP500
Combination cards, the trunk daughter card is pre-installed and cannot be changed.
Warnings
1. Correct anti-static protection steps should be taken while handling
circuit boards.
Parts and Equipment Required
1. o IP500 Base Card (except the IP500 Legacy Card Carrier).
2. o IP500 Trunk Daughter Card
3. o 3 Stand Off Pillars
These are supplied with the trunk daughter card.
Tools Required.
1. o 5mm Flat-blade screwdriver.
2. o Anti-static wrist strap and ground point.
Procedure: Installing a Trunk Daughter Card
1. Check that correct cards have been supplied.
2. Ensure that you are wearing an anti-static wrist strap connected
to a suitable ground point.
3. On the base card identify the position of 3 holes for the plastic
pillars for the IP500 card. These are along the same edge as the
card connector.
4. Fit the stand off pillars to the IP500 base card.
5. If there is a clip-on metal shield over the connector block on the
base card, remove it.
6. Using minimal force and checking that the pins are correctly
located, push the IP500 trunk card onto its connector block and
the stand off pillars.
7. Check that the card connector has snapped into position.
8. Using the washers and screws provided, secure the metal stand
off pillars to the base card.
9. A set of labels are supplied with the trunk daughter card. Fit the
appropriate label to the front of the base card.
IP Office Standard Version Installation
IP Office 7.0
Page 79
15-601042 Issue 23e (16 March 2011)
4.5.2 IP500 Legacy Card Preparation
An IP500 Legacy Carrier card can be used to fit IP400 trunk or VCM cards into an IP500 or IP500v2 control unit. Up to 2
IP500 legacy carrier cards can be inserted.
PRI T1
Dual PRI T1
PRI 30 E1 (1.4)
Dual PRI E1
PRI 30 E1R2 RJ45
Dual PRI E1R2 RJ45
BRI-8 (UNI)
ANLG 4 Uni (US only)
VCM
VCM
VCM
VCM
VCM
4
8
16
24
30
Warnings
1. Correct anti-static protection steps should be taken while handling
circuit boards.
Parts and Equipment Required
1. o IP500 Carrier Card
2. o IP400 Card
The table opposite lists supported cards. Any card not listed is not
supported. Cards are supplied with 2 plastic stand off pillars. Trunk
cards are also supplied with a replacement blanking plate which is
not required.
Tools Required
1. o 5mm Flat-blade screwdriver.
2. o Anti-static wrist strap and ground point.
Procedure: Installing a Carrier Card
1. Check that correct cards have been supplied.
2. Ensure that you are wearing an anti-static wrist strap connected to
a suitable ground point.
3. On the carrier card identify the position of the jumper block and
stand off pillar holes for the IP400 card. The peg holes are labeled
as VCM or TRUNK.
4. If fitting an IP400 trunk card, identify which of the plastic snap-off
panels on the front of the carrier card need to be removed to allow
the trunk cable connections. Carefully remove those panels.
5. Fit the stand off pillars to the IP500 carrier card.
6. Using minimal force and checking that the pins are correctly
located, push the IP400 card onto its jumper and the stand off
pillars.
IP Office Standard Version Installation
IP Office 7.0
Page 80
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: IP500 Card Installation
4.5.3 IP500 Card Insertion
Having prepared each IP500 base card by adding any trunk daughter card
be inserted into the control unit.
·
79
or IP400 legacy card
80
, the base card can
Warnings
· Correct anti-static protection steps should be taken while handling circuit boards.
· Cards must never be added or removed from the control unit while it has power connected.
· Tools Required
· o 5mm Flat-blade screwdriver.
· o Anti-static wrist strap and ground point.
Installing an IP500 Card
1. Check that there is no power to the control unit.
2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for
each card being installed. This cover is no longer required but should be retained until installation has been
completed.
3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit. When half inserted,
check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates remove it
and begin inserting it again.
4. The card should slide in freely until almost fully inserted. At this point apply pressure at the base of the front of the
card to complete insertion.
5. Using a flat-bladed screwdriver secure the card.
IP Office Standard Version Installation
IP Office 7.0
Page 81
15-601042 Issue 23e (16 March 2011)
4.6 Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Standard Version Installation
IP Office 7.0
Page 82
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Wall Mounting
4.6.1 Wall Mounting Kit V2
These notes relate to the IP500 Wall Mounting Kit V2 (SAP 700500923). This kit can be used to wall mountIP500v2 control
units and IP500 external expansion modules.
The kit includes all components necessary for wall mounting onto a plywood surface. The use of the cable covers is
optional.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
· The installation must be done by a service person only.
· For control units, the mesh flame screen must be installed in the bottom edge of the control unit before mounting.
· Ensure that the system has been shutdown and power has been removed from all the units. Shutdown the system
using a shutdown command and then remove power. Do not simply remove the power.
· If mounting a control unit, you must wait at least 15 minutes after removing the power cord before fitting the flame
screen.
· A suitable mounting surface of at least 19mm (0.75 inch) plywood is required.
IP Office Standard Version Installation
IP Office 7.0
Page 83
15-601042 Issue 23e (16 March 2011)
Wall Mounting Process
Figure 1
1. Shutdown the System
Ensure that the system has been shutdown and power has been removed
from all the units.
· If mounting a control unit, you must wait at least 15 minutes after
removing the power cord before fitting the flame screen.
· Shutdown the system using a shutdown command and then remove
power. Do not simply remove the power.
Figure 2
2. Fit the Flame Screen: Mandatory - Control Units Only (See Figure 1)
·
! WARNING: The flame screen mesh must be fitted.
a. Remove the cards or blank slot covers from the left-hand and righthand slots.
b. Insert the flame screen into the bottom of the control unit, with the
two black plastic pegs at the front.
c. Press the two pegs through the air flow holes in the control unit
casing.
Figure 3
d. Check that the pegs have come through and have secured the flame
screen in place and that the screen is flush with the chassis.
3. Attach Brackets on One Side (See Figure 2)
On one side of the unit, attach one pair of the metal brackets.
· Only use the screws provided with the wall mounting kit for attaching
the metal brackets.
4. Attach the Cable Cover and Bracket (See Figure 3)
Use of the cable covers is optional. If not being used, simply attach the other
pair of brackets to the other side of the unit; otherwise:
Figure 4
a. Hook one of the cable covers into the leading hole of one of the metal
brackets.
b. Hook another bracket onto the other end of the cable cover and then
attach that bracket to the unit.
Figure 5
c. Repeat the process to attach the other cable cover to the unit.
5. Fit the Wall Bracket (See Figure 4)
Using 2 of the screws provided with the kit, attach the wall bracket to the
plywood surface.
Figure 6
6. Place the Unit onto the Wall Bracket (See Figure 5)
Lift the unit onto the wall bracket. The two metal brackets at the top of the
unit hook over the top of the wall bracket.
7. Attach the Unit to the Wall Panel (See Figure 6)
a. Using the remaining 4 screws provided with the kit, fix the cover
brackets to the plywood surface.
b. Reinsert the base cards and blank slot covers.
IP Office Standard Version Installation
IP Office 7.0
Page 84
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Wall Mounting
4.6.2 Wall Mounting Kit V1
These notes relate to the older design of wall mounting kit (SAP 70043015) used
for IP500 and IP500v2 control units. This kit cannot be used for external expansion
modules.
The kit includes two brackets, one top and one bottom, and screws for attachment
to the control unit. Additional 4 x 4.5mm fixtures and fittings are required suitable
for the wall type.
In addition to the existing environmental requirements 54 for an IP Office system,
the following additional requirements apply when wall mounting a unit:
· The wall surface must be vertical, flat and vibration free. Attachment to
temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the
brackets to the control unit.
· The brackets must be used as shown, with the deeper tray-like bracket used
at the bottom of the wall mounted control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 85
15-601042 Issue 23e (16 March 2011)
4.7 Rack Mounting
The IP500 control unit and IP500 external expansion units can be
rack mounted if required into 19-inch rack systems. This requires
an IP500 Rack Mounting Kit (SAP 700429202) for each unit.
The kit includes:
· A rack mounting bracket and screws for attachment of the
bracket to the unit
· Nuts and bolts for rack attachment.
· Brackets and cable ties for cable tidying.
As indicated in the diagram following, the rack mounting bracket
can be used in several positions on the unit. IP400 external
expansion units used in an IP500 system can also be rack mounted
but use a separate IP400 Rack Mounting Kit.
Environmental Requirements
In addition to the existing environmental requirements
considered when rack mounting a unit:
54
for an IP Office system, the following additional factors must be
1. Rack Positioning - Ensure compliance with the rack manufacturers safety instructions. For example check that the
rack legs have been lowered and fixing brackets have been used to stop toppling.
2. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given
to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
· o Operating Temperature: 0°C (32°F) to 40°C (104°F).
· o Operating Humidity: 10% to 95% non-condensing.
3. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for
safe operation of the equipment is not compromised. Proper ventilation must be maintained. The side ventilation
slots on the IP500 control unit should not be covered or blocked.
4. Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
5. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
6. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
7.
Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 86
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Rack Mounting
·
Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 87
15-601042 Issue 23e (16 March 2011)
4.8 Connecting External Expansion Modules
Any external expansion modules should be connected to the control unit before
power is applied to the control unit. Ensure that modules are attached in the order
that matches the planned or pre-built configuration.
External expansion modules connect to the IP Office control unit using an
expansion interconnect cable. Each module is supplied with an expansion connect
cable and a power supply unit 33 . An appropriate locale specific power cord 34 for
the power supply unit must be ordered separately.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
Installation Requirements
· o Installation space either on or under the existing IP Office control unit.
· o Switched power outlet socket.
· o Available EXPANSION port on the control unit.
· o Grounding Requirements
· o Functional Grounding
Connection of a functional earth 38 is:
· o Recommend for all modules.
· o Connection of a functional ground is mandatory for Analog Trunk modules.
· o Protective Grounding
Connections of a protective ground via surge protection equipment 39 is:
· o Mandatory for Analog trunk modules in the Republic of South Africa.
· o Mandatory for Digital Station and Phone modules connected to out of building extensions.
· o Mandatory for Digital Station V2 and Phone V2 modules.
Tools Required
· o Manager PC.
· o Tools for rack mounting
86
(optional).
Parts and Equipment Required
· o External Expansion Module.
Each module is supplied with a suitable external power supply unit and a 1m blue interconnect cable. 2m Yellow
interconnect cables are supplied with the IP500 4-Port Expansion card and should only be used with that card.
· o Power cord for the power supply unit
· o Rack mounting kit
40
34
.
(optional).
· o Wall mounting kit - IP500 external expansion modules only (optional).
· o Cable labeling tags.
IP Office Standard Version Installation
IP Office 7.0
Page 88
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Connecting External Expansion Modules
Procedure
1. External expansion modules should not be attached to a control unit that has power.
2. If the IP Office system is being installed in a rack, attach the rack mounting kit
86
to the expansion module.
3. Attach the external expansion module's power supply but do not switch power on.
4. Connect the expansion interconnect cable from the module's EXPANSION port to the EXPANSION port on the control
unit. Make careful note of the port used and include this detail on the cable label and any other system records.
IP Office Standard Version Installation
IP Office 7.0
Page 89
15-601042 Issue 23e (16 March 2011)
4.9 Grounding
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially
important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and
data networks.
All IP Office control units and external expansion modules must be connected to a functional ground. Where the unit is
connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective
earth.
In some cases, such as ground start trunks, in addition to being a protective measure this is a functional requirement for
the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for
example areas of high lightning risk.
·
WARNING
During installation do not assume that ground points are correctly connected to ground. Test ground points before
relying on them to ground connected equipment.
· Additional protective equipment
In addition to grounding, additional protective equipment will be required in the following situations.
· On any Digital Station or Phones external expansion module connected to an extension located in another
building. Refer to "Out of Building Telephone Installations 39 ".
· In the Republic of South Africa, on all Analog Trunk external expansion modules (ATM16) and on any control
units containing an analog trunk cards (ATM4/ATM4U).
Tools Required
· o M4 Cross-Head Screwdriver.
· o Tools suitable for crimping a cable spade.
Parts and Equipment Required
· o 14AWG Solid copper wire for ground connection.
· o Cable sleeve matching local regulator requirements. Typically green for a functional ground and green/yellow for
a protective ground.
The ground point on IP Office control units and expansion modules are marked with a
or
symbol. Ground
connections to these points should use a 14 AWG solid wire with either a green sleeve for a functional ground or green and
yellow sleeve for a protective ground.
IP500/IP500v2 Control Unit
On IP500 control units the ground point is located above the RS232 DTE port.
External Expansion Modules
On expansion modules, the ground point is a 4mm screw located towards the right on the rear of the module.
· On some older modules, the dedicated ground point screw is not present. In those cases, the top-center cover
fixing screw (3mm) can be used as an alternative ground connection point. A toothed washer should be added to
ensure good contact.
IP Office Standard Version Installation
IP Office 7.0
Page 90
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Grounding
4.10 Network Connection
The section below details how a new IP Office system determines what IP address it should use. Note that this only applies
for a new system loading IP Office Release 7.0 and higher.
IP Address and DHCP Mode Resolution
When a defaulted or new IP Office control unit is switched on, it requests IP address information from a DHCP Server on
the network. This operation will occur whether the LAN cable is plugged in or not. The process below is done separately for
both the LAN port (LAN1 in the configuration) and the WAN port (LAN2 in the configuration) on the back of the IP Office
control unit.
· The IP Office makes a DHCP request for what IP address information it should use.
· If a DHCP server responds within approximately 10 seconds, the control unit defaults to being a DHCP client and
uses the IP address information supplied by the DHCP server.
· If no DHCP Server responds, the control unit still defaults to being the DHCP client but assumes the following
default addresses:
· LAN1: 192.168.42.1/255.255.255.0.
· LAN2: 192.168.43.1/255.255.255.0.
· Note that the IP Office does not check that these addresses are valid and or available on the network.
· Systems running in IP Office Standard Version mode can also be configured as a DHCP server. They can also be
configured to only provide DHCP for Avaya IP phones and or for remote access dial-in connections. DHCP Server
options are not supported for systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential
Edition - Norstar Version and IP Office Essential Edition - Quick Version modes.
·
! Once an IP500v2 control unit has obtained IP address and DHCP mode settings, it will retain those settings even
if rebooted without a configuration file present on the System SD card. To fully remove the existing IP address and
DHCP mode setting the IP Office must be defaulted using IP Office Manager.
PC Connection
Depending on the conditions that applied when the IP Office control unit was first started, a PC can be connected as
follows:
· If the IP Office is not connected to a network:
Connect the PC directly to the IP Office. It must be set to an address valid on the same network as the IP Office
defaults above.
· If the IP Office is connected to a network with no DHCP server:
Connect the PC directly to the IP Office. It must be set to an address valid on the same network as the IP Office
defaults above.
· If the IP Office is connected to a network with a DHCP server:
Connect the PC to the network. It must be set to be a DHCP client or to an address that is valid for the network.
IP Office Standard Version Installation
IP Office 7.0
Page 91
15-601042 Issue 23e (16 March 2011)
4.11 Starting the System
1. With the IP500v2 control unit shut down or unpowered, insert the Avaya
System SD card into the System SD slot on the rear of the control unit.
· Ensure that you have the correct card.
· Ensure that the card has the level of software required. If necessary
the card can be upgraded to match a version of IP Office Manager
74 .
2. Apply power to the external expansion modules if any. The power outlet
used must include a switch and in cases where the power cord includes
an earth lead, that outlet must have a protective earth connection.
3. Apply power to the IP500v2 control unit. The power outlet used must
include a switch and the power outlet must have a protective earth
connection.
4. The control unit will begin loading firmware from the System SD card with
which it will upgrade itself and the components installed in the control
unit.
5. This process takes approximately a minute. The end of this process will
be indicated by LED1 on each base card flashing every 5 seconds. LED9
on each base card fitted with a trunk daughter card will also flash every 5
seconds.
6. The control unit will then begin upgrading the external expansion
modules. This will be indicated by the red center LED on each module
flashing red. The process is completed when the LED changes to steady
green.
7. If a configuration file is already present on the System SD 74 card it is
loaded by the IP Office. If not, the IP Office creates a default
configuration based on the components of the system and copies that
configuration onto the System SD card.
8. It should be possible now to use IP Office Manager to access the
configuration of the IP Office.
The LEDs on the rear of the control unit go through the following sequence during a normal start up. Note that the times
are approximately only:
LED
4s
4s
12s
5s
2s
5s
5s
10s
10s
Finished
CPU
Orange
Green
Green
Green
Green
Green
Green
Green
Green
Green
System SD
Orange
Off
Green
Green
Green
Off
Green
Green
Green
Green
Red
Flash
Optional SD
If present.
Orange
Off
Green
Green
Green
Off
Off
Green
Green
Green
On the front of the control unit, LED1 on any IP500 base cards fitted is used as follows. LED9 is also used for any trunk
daughter cards fitted.
LED
30s
30s
Finished
LED1/LED9
Red
Red
Red
Fast Flash
Flash every 5
seconds
IP Office Standard Version Installation
IP Office 7.0
Page 92
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Starting the System
4.11.1 Checking the LEDs
Control Unit LEDs
LED
Description
Optional SD
·
·
·
·
System SD
CPU
Off = Card shutdown 167 .
Green on = Card present.
Green flashing = Card in use.
Orange steady = Reset imminent.
· Red flashing = Card initializing or shutting down.
· Red fast flashing = card full
· Red steady = Card failure/wrong type.
· Alternate red/green = Starting up.
· Green on = Okay.
· Red on = No software.
· Flashing Red = Error/Shutdown.
Base Card LEDs
Base Card
LEDs 1 to 8 Usage
All Cards
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
IP500 Analog Phone
· No status LEDs are used for analog phone extensions.
IP500 Digital Station
· Green On = Phone detected.
IP500 Combination
LEDs 1 to 6
· Green On = Phone detected.
IP500 VCM
· LEDs 1 to 8 are unlabelled. They are used to indicate voice compression channel usage.
Each LED lit represents 12.5% of the available voice compression channel capacity in
use (total card capacity rather than licensed capacity).
IP500 4-Port Expansion
LEDs 1 to 8 are used for the expansion ports on the rear of the control unit. LEDs 9 to 12
are used for the card's own expansion ports.
Green
On
Expansion module present.
Red
Flashing
Initializing.
Red
On
Error.
Orange
Regular Flash
Base card okay.
Trunk Daughter Card LEDs
Trunk Daughter Card
LEDs 9 to 12 Usage
All cards
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
Analog Trunk
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Trunk
·
·
·
·
BRI Trunk
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm indication
signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback mode (set
through IP Office System Monitor).
External Expansion Module LEDs
· Green on = Module okay.
· Red flashing = Module starting up/Loading firmware.
IP Office Standard Version Installation
IP Office 7.0
Page 93
15-601042 Issue 23e (16 March 2011)
· Green flashing = Module starting up/Loading firmware (IP500 DS16A/30A module).
· Red on = Error.
IP Office Standard Version Installation
IP Office 7.0
Page 94
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Starting the System
4.12 Changing the System to Standard Mode
If this is not the mode required for the IP Office system, IP Office Manager can be used to change the system to IP Office
Standard Version.
The process below will change the mode of the system and default its configuration.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Manual Changing to IP Office Standard Version Mode
1. Using IP Office Manager, receive the configuration from the system. The Manager application will automatically
switch to its simplified view as the configuration from a system running in .
2. Select File | Advanced | Switch to Standard Mode (Default).
3. From the Select IP Office menu, select the IP Office system and click OK.
4. Enter the service user name and password. The defaults are Administrator and password.
5. A change mode warning is displayed. Selecting Yes will reboot the IP Office system.
6. Once the system has rebooted, use IP Office Manager to again receive the configuration from the system. The user
name and password for configuration should be the IP Office Standard Version mode defaults Administrator and
Administrator.
7. The Manager application will automatically switch to its advanced view as the configuration is from a system
running in IP Office Standard Version.
Automating the Change to IP Office Standard Version Mode
If the only systems that you install are IP Office Standard Version mode, the Manager application can be used to automate
part of the process above.
1. In IP Office Manager, select File | Preferences.
2. On the Preferences sub-tab, enable Convert default Quick mode to Standard mode.
3. With this option enabled, when a configuration for a new or defaulted system running in IP Office Essential Edition Quick Version mode is received by Manager, it will automatically be converted to a IP Office Standard Version mode
configuration. This setting does not affect existing systems with non-default configurations.
4. ! Important: IP Address Settings Default to Server
The conversion will set the DHCP mode to Server and the LAN addresses to their defaults of 192.168.42.1 and
192.168.43.1. Using Manager to change these settings to the required values.
5. Sending the configuration back to the system will restart the system in IP Office Standard Version mode.
IP Office Standard Version Installation
IP Office 7.0
Page 95
15-601042 Issue 23e (16 March 2011)
4.13 Connecting Phones
During initial power up, the IP Office automatically creates extension and user entries for all analog and digital extension
ports (DS and TCM) in the system. This allows those devices to be connected without any additional programming.
·
! Warning
If the system has been upgraded from a previous release of IP Office software, all phones will be restricted from
making any calls until a system upgrade license 387 has been entered. The dialing restriction includes not being able
to make emergency calls.
· This section does not cover the installation of DECT, H323 and SIP telephones. For installation of those devices
refer to the appropriate supplementary installation manuals.
Analog Phones
Connect any analog phones to their appropriate Phone
are clearly labeled as such.
382
ports. Ensure that those connected to power failure ports
52
ETR Phones
Connect any ETR phones to their appropriate ETR
378
ports. These phones do not need to load additional firmware.
TCM Port Phones
Connect any TCM phones to their appropriate TCM
385
ports. These phones do not need to load additional firmware.
For some types of phone, the phone can only report its general type to the IP Office but not the specific model. It is
recommended that after connecting all the phones, the phone types should be correctly set in the IP Office configuration.
·
! Important
The default types cannot be changed after installation without defaulting the configuration. Therefore you must
ensure that you connect the correct type of phone to each port. If you need to swap phones, uses the process for
exchanging extension numbers 124 rather than swapping wiring.
1. Using IP Office Manager, receive the configuration from the system.
2. Select Extension.
3. Selecting each extension in turn, on the Extn tab, check that the Device Type field is set to the correct phone
model.
Default Type
Possible Phone Models
T7100
T7100, MT7100, MT7100N, Audio Conferencing Unit.
T7208
T7208, MT7208, MT7208N.
M7310
T7406E, T7406, M7310, M7310N
M7310BLF
T7316, M7310BLF
M7324
M7324, M7324N
4. Save the configuration back to the IP Office system.
DS Digital Stations
Connect any digital phones to their appropriate DS 376 ports. These phones may need to upgrade their firmware to match
that supported by the IP Office core software. The appropriate firmware is supplied with the IP Office Manager software
and copied onto the System SD card for IP500v2 systems.
The phones will automatically load the firmware from the IP Office system if necessary.
· The upgrade process takes approximately 10 minutes during which time the phone will display a warning. The
phone should not be disconnected during this process.
· Due to memory requirement, only 10 phones of the same type can be upgraded at a time. Starting from the first
port needing to be upgraded, the IP Office will upgrade all connected phones of the same type needing upgrading in
batches. It will then upgrade the next connected type of phones needing to be upgraded.
· Once the phone connected to a port has been upgraded, the IP Office will not check whether the phone on that port
needs to be upgraded again except following a system reboot, i.e. multiple phones cannot be upgraded by
swapping the connected phones on the same.
IP Office Standard Version Installation
IP Office 7.0
Page 96
15-601042 Issue 23e (16 March 2011)
IP500v2 Installation: Connecting Phones
· Avaya 2400 Series and 5400 Series phones need to have upgrading turned on or off. Refer to Upgrading
2400/5400 Phones 129 .
IP Office Standard Version Installation
IP Office 7.0
Page 97
15-601042 Issue 23e (16 March 2011)
Chapter 5.
Initial Configuration
IP Office Standard Version Installation
IP Office 7.0
Page 99
15-601042 Issue 23e (16 March 2011)
5. Initial Configuration
This section covers basic configuration changes required for all IP Office systems.
· Setting the System Locale 101
Setting the correct system locale affects a wide range of settings including trunk settings. The correct locale must
be set for a system to operate correctly.
· Extension Numbering 105
Renumber the user extensions if required.
· Change the Default Passwords 103
The default passwords used for configuration access to the IP Office system should be changed.
· Change the IP Address/DHCP Settings 102
If necessary, the IP address and DHCP mode of the IP Office system can be changed.
· Entering Licenses 107
If not already done, enter licenses for features that require them.
· Trunk Configuration
Some basic trunk configuration may be required.
· Remove Unused Trunks 108
Disabling the use of trunks and trunk channels that are not available.
· Select the Clock Source for Digital Lines 110
Altering which digital trunk is used to provide the IP Office with its clock signal for call synchronization.
· Enter Trunk Prefixes 112
On systems where a prefix is being used for external dialing, ensure that the same prefix is added to incoming
numbers in order to allow return calls.
IP Office Standard Version Installation
IP Office 7.0
Page 100
15-601042 Issue 23e (16 March 2011)
Initial Configuration:
5.1 Setting the System Locale
Setting the correct system locale 47 affects a wide range of settings including trunk settings. The correct locale must be
set for a system to operate correctly. It will also set the default language used for phone displays and for voicemail
prompts. However language settings can be changed separately from the system locale if different language operation is
required.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
· This process can be performed through phone based administration 68 from either of the first two systems in the
system. For details, refer to the Phone Based Administration manual.
Setting the System Locale
1. Start Manager
2. Click on
66
and receive the configuration from the IP Office system.
System.
3. Click on the System tab.
4. Use the Locale drop down list to select the required locale. The default language for the locale is shown in brackets,
for some locales there may be more than one entry with different default languages for each.
· Argentina
· France
· Netherlands
· South Africa
· Australia
· Germany
· New Zealand
· Spain
· Bahrain
· Greece
· Norway
· Sweden
· Belgium
· Hong Kong
· Oman
· Switzerland
· Brazil
· Hungary
· Pakistan
· Taiwan
· Canada
· Iceland
· Peru
· Turkey
· Chile
· India
· Poland
· United Arab Emirates
· China
· Italy
· Portugal
· United Kingdom
· Colombia
· Korea
· Qatar
· United States
· Denmark
· Kuwait
· Russia
· Venezuela
· Egypt
· Mexico
· Saudi Arabia
· Finland
· Morocco
· Singapore
5. Click on the
save icon and save the updated configuration back to the IP Office system.
IP Office Standard Version Installation
IP Office 7.0
Page 101
15-601042 Issue 23e (16 March 2011)
5.2 Changing the IP Address Settings
When a new or defaulted IP Office is switched on, the control unit will make a DHCP requests for IP address settings on
each of its LAN interfaces (LAN1 and LAN2).
· If the IP Office receives a response from a DHCP server, it will configure itself as a DHCP client using the address
details provided by the DHCP server.
· If the IP Office does not receive a response from a DHCP server, it will configure itself as a DHCP server and use
the following default address details:
Network Settings
LAN1
LAN2/WAN
IP address
192.168.42.1.
192.168.43.1
IP Mask
255.255.255.0
255.255.255.0
DHCP Mode
Server
Server
No of DHCP IP Addresses
200.
200.
If the IP address and DHCP mode settings are not suitable for the customers network they should changed. Note that
changing the IP Office's IP address settings requires it to restart.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Changing IP Address Settings
1. Start Manager
2. Click on
66
and receive the configuration from the IP Office system.
System.
3. On the System tab, in the Name field enter a distinctive name for the IP Office system. Click OK.
4. Click on the LAN1 tab.
5. On the LAN Settings sub-tab, change the IP Address, IP Mask and DHCP Mode settings to match the customer
requirements. These settings are used for the LAN port on the back of the IP Office control unit. Click OK.
6. Repeat the process for the LAN2 tab. Those settings are used for the WAN port on the back of the IP Office control
unit.
7. Click on the
save icon and save the updated configuration back to the IP Office system.
IP Office Standard Version Installation
IP Office 7.0
Page 102
15-601042 Issue 23e (16 March 2011)
Initial Configuration: Changing the IP Address Settings
5.3 Changing the Default Passwords
At a minimum you should change the password used for IP Office configuration access. An IP Office system's security
settings can be set back to default 147 if necessary using IP Office Manager.
Do not change any other settings than those described below until you have read and understood the IP Office Security
Mode section of the IP Office Manager manual.
Changing the Security Settings
1. Start Manager
66
and receive the configuration from the IP Office system.
2. Select File | Advanced | Security Settings.
3. Enter a user name and password of an account that has security configuration access to the IP Office system. The
defaults (which should be changed as part of this process) are security and securitypwd.
4. Click on
System and select the Unsecured Interfaces tab.
· The System Password is used by Manager for remote software upgraded of the IP Office system. The default
password is password. Click on the Change button and enter a new password. Click OK.
· Click OK.
Service Users. The list will show the service user accounts that exist to access the IP Office
5. Click on
configuration.
6. The default service users Administrator, Manager and Operator each use the same value (Administrator,
Manager and Operator) as their password. For each of these service users:
· Click on the service user name. In the Service User Details tab, click on Change and enter a new password.
Click OK.
· Click OK.
IP Office Standard Version Installation
IP Office 7.0
Page 103
15-601042 Issue 23e (16 March 2011)
General . The general security settings are displayed in the main display area.
7. Click on the
· Click on Change and enter a new password for the security administrator.
8. Click on File | Configuration to exit security configuration mode and return to the IP Office configuration.
Changing the Remote User Password
The IP Office configuration contains a user whose password is used as the default for remote dial in access to the IP Office
network. The password of this user should be changed.
1. Start Manager
2. Click on
66
and connect to the IP Office system.
Users and in the list of users click on Remote Manager.
3. On the User tab, enter a new password for the user and click OK.
4. Click on the
icon and save the updated configuration back to the IP Office system.
IP Office Standard Version Installation
IP Office 7.0
Page 104
15-601042 Issue 23e (16 March 2011)
Initial Configuration: Changing the Default Passwords
5.4 Extension Numbering
Extension Numbering:
· IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version mode systems can use 2-digit or 3-digit numbering. In 2-digit systems, the user extensions
are fixed as 10 to 57. In 3-digit systems the user extension are numbered 100 upwards by default but can be
renumbered in the range 100 to 579.
· IP Office Standard Version mode systems can use a mix of extension numbers up to 9 digits in length. By default
extensions are given 3-digit extension numbers starting from 201 upwards.
· In IP Office Standard Version mode, extension numbers are also used for hunt groups. In other modes, hunt groups
have fixed numbers that cannot be used for extensions.
Number of Extensions:
·
IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version modes supports 48 extensions in 2-digit numbering mode. 100 extensions are supported in
3-digit numbering mode.
· IP Office Standard Version mode supports up to 384 extensions.
Changing Extension Numbers
IP Office Manager can be used to renumber all extensions on the system. This will also update any references to the
extension number in other configuration fields.
1. Start Manager
66
and receive the configuration from the IP Office system.
2. Select Tools | Extension Renumber.
3. Click on the
save icon and save the updated configuration back to the IP Office system.
Changing an Individual User's Extension Number
1. Select
User. Locate and select the relevant user.
IP Office Standard Version Installation
IP Office 7.0
Page 105
15-601042 Issue 23e (16 March 2011)
a. On the User tab, change the Extension number to the required new number.
b. Click on another field. If an error warning appears it will most likely be due to a conflict with an existing use of
that extension number.
· If this an error, click Cancel to return the user to their original extension number.
· If this is intended as the other entry will be corrected click OK and then edit the other entry.
· When OK is clicked, Manager will automatically propagate the number change to any hunt groups,
incoming call routes, user buttons, bridged appearance buttons and call coverage appearance buttons
associated with the user's original extension number.
2. If the user has an extension with which they are associated by being the extension's Base Extension setting, that
setting is not automatically updated. If the user should still be associated with that extension by default, the
extension must be updated manually to match the user's new extension number.
a. Select
Extension.
b. Change the Base Extension number to match the user extension who should now be associated with that
extension port by default.
c. Click OK. Manager will probably give a validation error message due to a user being associated with two
extensions. This can be ignored until all the user moves have been completed.
3. If changing several users repeat the processes as required.
4. Click
to revalidate the configuration and check that no conflicts between users and associated extensions.
5. If the configuration changes are complete, send the configuration back to the IP Office and select appropriate
settings for the reboot.
IP Office Standard Version Installation
IP Office 7.0
Page 106
15-601042 Issue 23e (16 March 2011)
Initial Configuration: Extension Numbering
5.5 Entering Licenses
For IP500v2 control units, license files can be pre-loaded 77 onto the System SD card. Those licenses 386 will then be
merged with the configuration when the control unit is powered up. Otherwise for all control units, licenses can be entered
into the configuration using IP Office Manager. In addition to the methods below, license can also be added by placing the
addition licenses as a text file on the System SD card 77 .
You must ensure that the licenses being entered have been issue against the FK serial number of the System SD card
fitted in the system. Each license is a unique 32-character string based on the feature being licensed and the serial
number of the SD card plugged into the system control unit.
Entering licenses manually is liable to errors caused by miskeying the correct 32-character string.
Entering Licenses
1. Start Manager
2. Select
66
and receive the configuration from the IP Office system.
System.
3. The field Dongle Serial Number shows the serial number of the Feature Key Dongle is already detected. Check
that this number matches the one against which the licenses have been issued.
4. Click OK.
5. Select
License.
and select License. Enter the new license and click OK. We recommend that add licenses
6. To add a license, click
by cut and pasting them from a supplied file listing each 32-character license keys. That avoids potential issues
with mistyping.
7. The Status of the new license should show Unknown and name the license as expected. If the name is Invalid,
the most likely cause is incorrect entry of the license key characters.
8. Click on the
save icon to send the configuration back to the IP Office.
9. Use Manager to receive the configuration again and check that the status of the license. It should now be Valid.
IP Office Standard Version Installation
IP Office 7.0
Page 107
15-601042 Issue 23e (16 March 2011)
5.6 Disable Unused Trunks
Each IP Office trunk card provides a fixed number of trunk ports with digital trunk ports supporting a fixed number of
digital channels. By default the IP Office configuration will have settings for all the possible trunks and channels.
In cases where the number of trunks or trunk channels in use or licensed is lower than the number supported by the trunk
card, the unused trunks and channels must be disabled.
·
Failure to do this will cause problems with outgoing calls. For example, on a system with an ATM4 trunk card
fitted but only two analog trunks actually connected, failure to disable the other two trunks within the IP Office
configuration will cause 50% of outgoing call attempts to fail.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Disabling Trunks
1. Start Manager
66
and receive the configuration from the IP Office system.
2. Within the IP Office configuration, select
Line.
3. For each line, set those lines or channels that are not connected or being used as out of service. The location of the
relevant setting varies for each trunk type.
· Analog Trunks
To disable the whole trunk, on the main form set the Admin option to Out of Service.
· BRI, E1 PRI, S0 and QSIG Trunks
To disable the whole trunk, on the main form set the Admin option to Out of Service. Otherwise set the
number of channels to match the actual subscribed channels.
IP Office Standard Version Installation
IP Office 7.0
Page 108
15-601042 Issue 23e (16 March 2011)
Initial Configuration: Disable Unused Trunks
· T1, T1 PRI and E1R2 Trunks
To disable the whole trunk, on the main form set the Admin option to Out of Service. Otherwise select the
Channels tab and set those channels that are not used to Out of Service.
· For T1 set the Type to Out of Service.
· For T1 PRI set the Admin field to Out of Service.
· For E1R2 trunks set the Line Signalling Type to Out of Service.
IP Office Standard Version Installation
IP Office 7.0
Page 109
15-601042 Issue 23e (16 March 2011)
5.7 Setting the Digital Trunk Clock Source
Digital trunks require the telephone system at each end of the trunk to share a clock signal to ensure synchronization of
call signalling. The IP Office can obtain and use the clock signal from any of its digital trunks. Typically the clock signal
provided by a digital trunk from the central office exchange is used as this will be the most accurate and reliable clock
source.
To do this, the Clock Quality setting on each line in the IP Office configuration is set to one of the following:
· Network
If available, the clock signal from this trunk should be used as the IP Office's clock source for call synchronization.
If several trunk sources are set as Network, the IP Office will default to using one as detailed below.
· Fallback
If available, the clock signal from this trunk can be used as the clock source if none of the trunks set as Network
are providing a clock source.
· Unsuitable
The clock source from this trunk will never be used as the IP Office's clock source.
If no clock source is available the IP Office can use its own internal clock if necessary.
In the example below the first IP Office is set to use the public network trunk as its clock source and ignoring the possible
clock source from the QSIG trunk. The other IP Office system is using the clock signal received from the first IP Office on
its QSIG trunk as its clock source. Thus both IP Offices are using the same clock source and that clock source is the public
network exchange.
Multiple Source Priority
When multiple trunks with the same setting are providing clock signals, the trunk used is determined in the following order
of priority.
· IP500 and IP500v2 Control Units: Trunks are used in the order of slots 1 to 4 and then by port on each slot.
· IP421 and IP406 V2 Control Units: Trunks are used in the order Slot B ports 1 to 4, then Slot A ports 1 to 4.
Viewing the Current Clock Source
The current clock source being used by an IP Office system is shown on the Resources page within the IP Office System
Status Application.
IP Office Standard Version Installation
IP Office 7.0
Page 110
15-601042 Issue 23e (16 March 2011)
Initial Configuration: Setting the Digital Trunk Clock Source
Setting a Trunk Clock Quality Setting
1. Within the IP Office configuration, select
Line.
2. For each digital line, select the line and on the Line tab select whether that trunk should provide the clock source for
the network or whether the trunk is unsuitable. For E1R2 trunks the Clock Quality setting is on the Advanced
tab.
3. Ensure that only one trunk is set to Network. This should preferably be a direct digital trunk to the central office
exchange.
4. One other trunk can be set a Fallback should the selected Network trunk connection be lost. If possible this should
be a trunk from a different provider since that reduces the chances of both sources failing at the same time.
5. Ensure that all other digital trunks are set as Unsuitable.
IP Office Standard Version Installation
IP Office 7.0
Page 111
15-601042 Issue 23e (16 March 2011)
5.8 Setting the Trunk Prefixes
Where a prefix has been implemented for outgoing calls, that same prefix needs to be added to trunk settings. The prefix
is then used as follows:
· On incoming calls the prefix is added to any incoming ICLID received with the call. That allows the ICLID to be used
by IP Office phones and applications to make return calls.
· On outgoing calls, the short codes used to route the call to a trunk must remove the dialing prefix.
1. Within the IP Office configuration, select
Line.
2. For each line enter the prefix. The location of the relevant setting varies for each trunk type.
· Analog Trunks
· T1 and T1 PRI Trunks
IP Office Standard Version Installation
IP Office 7.0
Page 112
15-601042 Issue 23e (16 March 2011)
Initial Configuration: Setting the Trunk Prefixes
· BRI, E1 PRI, S0 and QSIG Trunks
SIP Trunk Prefixes
For IP Office Release 6, the prefix fields Prefix, National Prefix, Country Code and International Prefix are available
with the SIP Line settings. These fields are used in the following order:
1. If an incoming number (called or calling) starts with the + symbol, the + is replaced with the International Prefix
.
2. If the Country Code has been set and an incoming number begins with that Country Code or with the
International Prefix and Country Code, they are replace with the National Prefix.
3. If the Country Code has been set and the incoming number does not start with the National Prefix or
International Prefix, the International Prefix is added.
4. If the incoming number does not begin with either the National Prefix or International Prefix, then the Prefix is
added.
For example, if the SIP Line is configured with prefixes as follows:
· Line Prefix: 9
· National Prefix: 90
· International Prefix: 900
· Country Code: 44
Number Received
Processing
Resulting Number
+441707362200
Following rule 1 above, the + is replace with the International Prefix
(900), resulting in 900441707362200.
901707362200
The number now matches the International Prefix (900) and Country
Code (44).Following rule 2 above they are replace with the National
Prefix (90).
00441707362200
Following rule 2 above the International Prefix (900) and the Country 90107362200
Code (44) are replaced with the National Prefix (90).
441707362200
Following rule 2 above, the Country Code (44) is replace with the
National Prefix (90).
901707362200
6494770557
Following rule 3 above the the International Prefix (900) is added.
9006494770557
IP Office Standard Version Installation
IP Office 7.0
Page 113
15-601042 Issue 23e (16 March 2011)
Chapter 6.
Additional Processes
IP Office Standard Version Installation
IP Office 7.0
Page 115
15-601042 Issue 23e (16 March 2011)
6. Additional Processes
This section covers the following additional installation processes:
· Switching Off an IP Office System
· Rebooting an IP Office System
· Memory Card Removal
120
· Changing Components
122
· Swapping Extension Users
119
124
· Upgrading the IP Office Software
· Out of Building Extensions
· SNMP
125
39
· Using the External Output Port
· So8 BRI Modules
117
135
136
139
· Reset Button Usage
· AUX Button Usage
143
143
· DTE Port Maintenance
144
IP Office Standard Version Installation
IP Office 7.0
Page 116
15-601042 Issue 23e (16 March 2011)
Additional Processes:
6.1 Switching Off an IP Office System
IP Office systems running IP Office Release 6 can be shut down in order to perform maintenance. The shut down can be
either indefinite or for a set period of time after which the IP Office will automatically reboot.
During the shut down process, the current configuration in the control unit's RAM memory is copied to the control units
non-volatile memory. For IP500v2 systems that location is the System SD card.
For control units with memory cards the memory cards can be shutdown and restarted
167
separately from the system.
! WARNINGS
· A shutdown must always be used to switch off the system. Simply removing the power cord or switching off the
power input may cause errors.
· This is not a polite shutdown, any users calls and services in operation will be stopped. Once shutdown, the system
cannot be used to make or receive any calls until restarted.
· The shutdown process takes up to a minute to complete. When shutdown, the CPU LED and the IP500 base card
LEDs 1 and 9 (if trunk daughter card fitted) will flash red rapidly. The memory card LEDs are extinguished. Do not
remove power from the system or remove any of the memory cards until the system is in the this state.
· To restart a system when shutdown indefinitely, or to restart a system before the timed restart, switch power to
the system off and on again.
System Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | System Shutdown.
2. Using the Select IP Office menu, the System Shutdown Mode menu is displayed.
3. Select the type of shutdown required. If Indefinite is used, the system can only be restarted by having its power
switched off and then on again. If a Timed shutdown is selected, the IP Office will reboot after the set time has
elapsed.
System Shutdown Using the System Status Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Shutdown System.
4. Select the time duration for the shutdown or indefinite.
IP Office Standard Version Installation
IP Office 7.0
Page 117
15-601042 Issue 23e (16 March 2011)
System Shutdown Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400,
5600, 9400, 9500 or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to
restrict access to system administration functions on the phone.
Unlike Manager, a system phone user cannot select an indefinite shutdown. They can set a timed shut down of between 5
minutes and 24 hours.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select System Shutdown.
4. Select a time period for the shutdown. It must be in between 5 minutes and 24 hours.
5. Press Done and then Confirm to begin the shutdown.
System Shutdown Using the IP500v2 AUX Button
When the AUX button is pressed for more than 5 seconds, the IP500v2 control unit will shutdown with the restart timer
set to 10 minutes.
IP Office Standard Version Installation
IP Office 7.0
Page 118
15-601042 Issue 23e (16 March 2011)
Additional Processes: Switching Off an IP Office System
6.2 Rebooting an IP Office System
You can use IP Office Manager to reboot an IP Office system.
1. Using IP Office Manager, select File | Advanced | Reboot.
2. Use the Select IP Office menu to locate and select the IP Office system. Enter a valid user name and password.
3. The type of reboot can then be selected.
· Reboot
Select when the reboot should occur.
· Immediate
Send the configuration and then reboot the IP Office.
· When Free
Send the configuration and reboot the IP Office when there are no calls in progress. This mode can be
combined with the Call Barring options.
· Timed
The same as When Free but waits for a specific time after which it then wait for there to be no calls in
progress. The time is specified by the Reboot Time. This mode can be combined with the Call Barring
options.
· Reboot Time
This setting is used when the reboot mode Timed is selected. It sets the time for the IP Office reboot. If the
time is after midnight, the IP Office's normal daily backup is canceled.
· Call Barring
These settings can be used when the reboot mode When Free is selected. They bar the sending or receiving of
any new calls.
4. Click OK.
IP Office Standard Version Installation
IP Office 7.0
Page 119
15-601042 Issue 23e (16 March 2011)
6.3 Memory Card Removal
Card
Removal
Memory cards should always be shutdown 167 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
Before a memory card is removed from an IP Office system that is running, the card must be shutdown. Removing a
memory card while the system is running may cause file corruption.
Card services can be restarted by either reinserting the card or using a Start Up command.
Card Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Shutdown.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
Card Shutdown Using the System Status Application Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Shutdown.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
Card Shutdown Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select System for the System SD card or Option for the Optional SD card.
5. Select Shutdown.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
IP Office Standard Version Installation
IP Office 7.0
Page 120
15-601042 Issue 23e (16 March 2011)
Additional Processes: Memory Card Removal
Card Reinsertion
Reinserting a memory card into a system that is already switched on will automatically restart card operation. However, if
the card has been shutdown but not removed, it can be restarted using Manager without requiring a reboot.
Card Startup Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Startup.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
Card Startup Using the System Status Application
3. Start System Status
67
and access the IP Office's status output.
4. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Start Up.
Card Startup Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
4. Select Features | Phone User | System Admin.
5. Enter your IP Office user login code.
6. From the menu select Memory Card.
4. Select System for the System SD card or Option for the Optional SD card.
5. Select Startup.
IP Office Standard Version Installation
IP Office 7.0
Page 121
15-601042 Issue 23e (16 March 2011)
6.4 Changing Components
Except for memory cards (see Memory Card Removal 120 ), cards and external expansions modules must only be removed
and added to an IP Office system when that system is switched off 117 .
In the sections below, the term component can refer to a card fitted into the IP Office or an external expansion module.
Note that for extension ports, by default both an extension entry and a user entry will exist in the IP Office configuration.
Extension entries can be deleted without deleting the corresponding user entry. This allows retention of the user settings
and association of the user with a different extension by changing that extensions Base Extension number to match the
user's Extension ID.
Like for Like Replacement
If replacing with a componenet of the same type no configuration changes are necessary.
1. Switch off the IP Office system
117 .
2. Remove the card or external expansion module. Note the card slot or expansion port used as the replacement must
be installed in the same position.
3. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 88 ).
78
, Adding
4. Restart the IP Office system.
Higher Capacity Replacement
If replacing with a component of the same type but higher capacity, when restarted the IP Office will automatically create
configuration entries for the new trunks or extensions/users.
1. Switch off the IP Office system
117 .
2. Remove the card or external expansion module. Note the card slot or expansion port used as the replacement must
be installed in the same position.
3. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 88 ).
78
, Adding
4. Restart the IP Office system.
5. Use Manager to configure the new trunks or extensions/users.
Lower Capacity Replacement
If replacing with a component of the same type but lower capacity, after restarting the IP Office the configuration will need
to be edited to remove redundant entries.
1. Switch off the IP Office system
117 .
2. Remove the card or external expansion module. Note the card slot or expansion port used as the replacement must
be installed in the same position.
3. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 88 ).
78
, Adding
4. Restart the IP Office system.
5. Use Manager to delete the trunks or extensions/users in the configuration that are no longer supported by the
component installed.
IP Office Standard Version Installation
IP Office 7.0
Page 122
15-601042 Issue 23e (16 March 2011)
Additional Processes: Changing Components
Adding a New Component
If adding a new component to an available slot or port, when restarted the IP Office will automatically create configuration
entries for the new trunks or extensions/users.
1. Switch off the IP Office system
117 .
2. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 88 ).
78
, Adding
3. Restart the IP Office system.
4. Use Manager to configure the new trunks or extensions/users.
Permanent Removal
If permanently removing the component, the configuration will need to be edited to remove redundant trunk or extension/
user entries.
1. Switch off the IP Office system
117 .
2. Remove the card or external expansion module.
3. Restart the IP Office system.
4. Use Manager to delete the trunks or extensions/users in the configuration that relate to the component removed.
5. In the Control Unit section of the configuration, delete the entry for the component that is no longer present in the
system.
Replacement of a Different Type
If replacing a component with one of a different type, the process should be divided into two stages. First remove the
existing component using the Permanent Removal process above and adjust the configuration and reboot. Then install
the new component using the Adding a New Component process above.
IP Office Standard Version Installation
IP Office 7.0
Page 123
15-601042 Issue 23e (16 March 2011)
6.5 Swapping Extension Users
Whilst the example below shows 2 users swapping extensions the method can be used to swap multiple users within the
configuration and effecting the swaps after a single merge of the configuration changes.
For this example User A (202) and User B (203) want to swap extensions.
1. Load the IP Office configuration and select
Extension.
2. Locate the extension with the Base Extension set to 202, ie. matching User A's extension number.
· If the group pane is visible (View | Group Pane) in IP Office Manager, it shows the extension details (ID,
Module, Port and Base Extension).
3. Select that extension and change its Base Extension setting to 203, ie. to now match User B's extension number.
If IP Office Manager is set to validate edits, it will warn that this change conflicts with the existing Base Extension
setting of another extension. Ignore the warning at this stage. Click OK.
4. Locate the other extension with the Base Extension set to 203, ie. matching User B's extension number.
5. Select that extension and change its Base Extension setting to 202, ie. to now match User A's extension number.
If the error pane is visible (View | Error Pane), the warnings about extension conflicts should now disappear.
Click OK.
6. Save the configuration back to the IP Office system.
7. At each of the extensions dial the log out short code set on the IP Office system. By default this is *36.
· If any of the users is set to Forced Login, they will have to complete the login process at their new extension
using their Login Code.
IP Office Standard Version Installation
IP Office 7.0
Page 124
15-601042 Issue 23e (16 March 2011)
Additional Processes: Swapping Extension Users
6.6 Upgrading the IP Office Software
The installed IP Office Manager includes IP Office software files for control units, external expansion modules and phones
appropriate to the IP Office software level.
· New IP500v2 Systems
For the first 90 days, a new IP500v2 control unit will run any supported IP Office Release without requiring an
upgrade license. The highest level run is written into the system's memory (not the SD card) and that becomes a
permanent entitlement for the control unit. However, after 90 days the IP500v2 will require an upgrade license if
upgraded to a software release higher than any that it has run in the initial 90 day period.
·
Warning
Systems upgraded without the appropriate license will display "No license available" and will not allow any
telephony functions.
The IP Office system can be upgraded in two ways:
· Using the IP Office Manager Upgrade Wizard 126
The upgrade wizard is part of IP Office Manager and can be used to upgrade all types of IP Office system.
· Upgrading the System SD Card 128
For IP500v2 control units, the software on the System SD card can be upgraded by a range of methods, i.e. directly
upgrading the SD card or using the upgrade wizard. When the system is rebooted it will use the new software.
WARNINGS
· Check IP Office Technical Bulletins
Check the latest IP Office Technical Bulletin for the IP Office software release before proceeding any further. It may
contain information relating to changes that occurred after this document was completed. Bulletins are available
from http://support.avaya.com.
· Upgrade Path/Multi-Stage Upgrades
Due to the need to adjust internal memory allocation and configuration storage, for some upgrades the control unit
may need to perform multi-stage upgrade process. The table below indicates the require upgrade paths.
Platform
Current Release
Upgrade Step 1
IP500
4.0 / 4.1 / 4.2 / 5.0
Load 7.0
IP500v2
6.0
Load 7.0
All modules
4.0 / 4.1 / 4.2 / 5.0
Load 7.0
· Multiple Managers
If more than one copy of Manager is running it is possible for the IP Office to request BIN files from a different
Manager from the one that started the upgrade process. Ensure that only one copy of Manager is running when
upgrading an IP Office system.
· Other IP Office Applications
Upgrading the core software of the IP Office control unit may require upgrades to associated software. Typically IP
Office is compatible with the previous release of most IP Office applications, however for each IP Office core
software release there may be exceptions. These exceptions will be detailed in the Technical Bulletin for the IP
Office core software release.
IP Office Standard Version Installation
IP Office 7.0
Page 125
15-601042 Issue 23e (16 March 2011)
6.6.1 Using the Upgrade Wizard
1. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
a. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
b. Using IP Office Manager, select File | Open Configuration.
c. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
d. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
e. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Select File | Advanced | Upgrade. The UpgradeWiz is started and scans for IP Office modules using the Unit/
Broadcast address. Adjust this address and click Refresh if the expected control units are not shown.
2. The information displayed depends on the type of control unit.
· For IP500v2 control units
The current version of each IP Office .bin file held in the control units memory is shown. That is regardless of
whether that .bin file is currently being used by any module in the system.
· For other control units
For the control unit and each external expansion module present in the system, the current version of software
installed is displayed.
3. The Version column indicates the current version of software installed. The Available column indicates the version
of software Manager has available. If the available version is higher, the check box next to that row is automatically
selected.
· If any of the modules have pre-version 2.1 software installed, an upgrade with Validate unticked is required.
If this is the case, only continue with the upgrade process using a PC with a fixed IP address on the same LAN
domain and physical LAN segment as the IP Office control unit and only upgrade the pre-2.1 system.
· If a multi-stage upgrade is necessary, use the following additional steps to select the appropriate interim
software:
· Right-click on the upgrade wizard and click Select Directory. Locate and select the directory containing
the bin file for the intermediate software level.
· The upgrade wizard should now list just the control unit as having upgrade software available.
IP Office Standard Version Installation
IP Office 7.0
Page 126
15-601042 Issue 23e (16 March 2011)
Additional Processes: Upgrading the IP Office Software
· Upgrading to particular levels of IP Office software require a Software Upgrade X license where X is a
number. The Licensed and Required License columns indicate the current highest upgrade license the
system has and the required software upgrade license for the currently installed software. It does not indicate
the license requirement for the level of software in the Available column. For IP500v2 systems, a value of 255
indicates that the control unit is still in its initial 90 days where it can be upgraded without requiring a license.
4. For those modules which you want to upgrade, tick the check box.
5. For IP500v2 control units, the following additional options are available:
· Backup System Files
If selected, before upgrading to the new software, the current files in the System SD cards /primary folder
will be copied to its /backup folder.
· Upload System Files
If selected, the full set of software files that Manager has is copied to the /primary folder on the System SD
card. In addition to control unit and module software this will include phone software files. Following the
reboot, the phone will upgrade using those files if necessary.
· Restart IP Phones
If selected, following the upgrade and reboot, all Avaya IP phones are also restarted. This will cause them to
recheck whether the firmware they currently have loaded matches that on their configured file server. Use this
option if the IP Office system is the file server and the upgrade included new IP phone firmware.
6. Select Upgrade. The system password for each system will be requested. Enter it and click OK. The next steps
depend on the upgrade options selected. Do not cancel or close the upgrade wizard while these processes are
running.
· Validated Upgrade
If using the Validated option, a number of actions take place as follows;
a. The upgrade wizard checks the amount of free RAM memory available in the control unit to temporarily
store the new BIN files. If insufficient memory is available, you will be prompted whether to continue with
an off-line upgrade or cancel upgrading.
· If offline is selected, the IP Office is rebooted into offline mode. It may be necessary to use the
Refresh option within the Upgrade Wizard to reconnect following the reboot. Validate upgrade can
then be attempted to again check the amount of available RAM memory for transfer of BIN files. If the
memory is still insufficient, the option is offered to either do an unvalidated upgrade or cancel.
b. The bin files required are transferred to the system and stored in temporary memory.
c. For IP500v2 control units, the backup system files and upload system files actions are performed.
d. Once all file transfers are completed, the upgrade wizard will prompt whether it okay to proceed with the
upgrade process. Select Yes to continue.
e. Each module being upgraded will delete its existing core software, restart and load the new software file
that was transferred. This process may take several minutes for each unit.
· Unvalidated Upgrade
This method of upgrading should be avoided unless absolutely necessary. It is only required for IP Office
systems with pre-2.1 software and should only be done from a Manager PC with a fixed IP address running on
the same LAN segment and subnet as the IP Office system. During the upgrade the units and modules erases
their current software and then request the new software file from Manager.
7. Following the upgrade check that the upgrade wizard now shows that the selected units and modules have
upgraded. It may be necessary to select Refresh to update the information in the upgrade wizard display.
8. Repeat the process as required.
IP Office Standard Version Installation
IP Office 7.0
Page 127
15-601042 Issue 23e (16 March 2011)
6.6.2 Using an SD Card
In addition to using the traditional IP Office Upgrade Wizard 126 , IP500v2 control units can be upgraded by loading the
required set of firmware files onto the System SD card and rebooting the system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
There are a number of ways in which this can be done.
Method
Using Manager
165
System SD Card
Upgrade 165
Upgrade from
Optional SD Card
166
Description
Location
Using IP Office Manager, the contents of the card are
compared to the files that Manager has available and
are upgraded if necessary.
Local or
Remote
In this method, the System SD card is shut down and
removed from the control unit. The card's contents are
upgraded using IP Office Manager.
Local
This method uses an SD card loaded with the required
version of IP Office software. The card is inserted into
the control unit's Option SD card slot and its contents
copied to the System SD card.
Local
IP Office Standard Version Installation
IP Office 7.0
Software
Files
Embedded
Voicemail
Prompts
–
Page 128
15-601042 Issue 23e (16 March 2011)
Additional Processes: Upgrading the IP Office Software
6.6.3 Upgrading 2400/5400 Phones
The firmware on most phones connected to an IP Office system is automatically upgraded if necessary when a phone is
first connected to an IP Office port or for existing phones, after a system reboot. However this does not apply to Avaya
2400 Series and 5400 Series phones.
Checking the Firmware on a 2410 or 5410 Phones
1. Press
Exit to ensure that the phone has exited any other usage mode.
2. Press either of the display keys next to MENU.
3. Select OPTION.
4. Select Self Test. The display should now show details of the phone's currently installed firmware.
5. The firmware loaded into the phones has a major and minor version. The Major version in the example above is
shown as FWV=2 and the minor version is shown as REL:2.00.
6. Press
Exit to exit self test mode.
Checking the Firmware on a 2420 or 5420 Phones
1. Select OPTION.
2. Select Self Test. The display should now show details of the phone's currently installed firmware.
3. The firmware loaded into the phones has a major and minor version. The Major version in the example above is
shown as FWV=4 and the minor version is shown as REL:4.00.
4. Press Done to exit self test mode.
IP Office Standard Version Installation
IP Office 7.0
Page 129
15-601042 Issue 23e (16 March 2011)
Procedure: Forcing a Software Upgrade
· The following procedure should only be used if it has been determined that the 2400/5400 Series phones need
to be manually forced to change their firmware. During this process the phone cannot be used.
· For the IP Office 4.1 Q1 2008 maintenance release and higher, using the batch file to enable the phones to
upgrade their firmware is ignored unless the No User user Source Number of ALLOW_5410_UPGRADES is
added to the IP Office configuration.
1. Locate the Manager program directory and within it the files turn_on.bat and turn_off.bat.
2. Right-click on turn_on.bat and select Edit.
3. Locate the entry <IP Address> and replace this with the IP address of the IP Office system.
4. Close the file and save the changes.
5. Repeat steps 2 to 4 for the file turn_off.bat.
6. Ensure that Manager is running and is enabled to run as a TFTP Server. Manager acts as the TFTP server from
which the phones will request firmware files.
7. Double-click on the file turn_on.bat.
8. A prompt window should appear asking you to wait and eventually, if successful, Press any key to continue.
9. Within Manager, select File | Advanced | Reboot and reboot the IP Office system.
10.Following the system restart, the 2400 and 5400 Series phones will display Upgrading firmware, please wait and
then FIRMWARE UPDATE IN PROGRESS.
11.Once all the phones have completed their upgrade, double-click on turn_off.bat.
IP Office Standard Version Installation
IP Office 7.0
Page 130
15-601042 Issue 23e (16 March 2011)
Additional Processes: Upgrading the IP Office Software
6.7 Out of Building Telephone Installations
The following are the only supported scenarios in which wired extensions and devices outside the main building can be
connected to the IP Office system. In these scenarios, additional protection, in the form of protective grounding and surge
protectors, must be fitted.
·
WARNING
The fitting of additional protection does not remove the risk of damage. It merely reduces the chances of damage.
· Cables of different types, for example trunk lines, phone extensions, ground and power connections, should be kept
separate.
· All cabling between buildings should be enclosed in grounded ducting. Ideally this ducting should be buried.
· A Primary Protection Box must be provided at the point where the cables enter the building. This should be three
point protection (tip, ring and ground). Typically this would be gas tube protection provided by the local telephone
company. The ground wire must be thick enough to handle all the lines being affected by indirect strike at the same
time.
Connection Type
Protection Device Type
Requirement
Analog Phone Extensions
Phones External expansion
module (POT 382 or PHONE 382 )
ports only.
IP Office Barrier Box 133
· Connection from the expansion module to the
Supports a single connection.
phone must be via a surge protector at each end
Maximum of 16 on any expansion
and via the primary protection point in each
module.
building.
DS Phone Extensions
ITWLinx towerMAX DS/2 132
External expansion module DS Supports up to 4 connections.
376 ports only.
(This device was previously
referred to as the Avaya 146E).
TCM Phone Extensions
None
Analog Trunks
ITWLinx towerMAX CO/4x4
ITWLinx towerMAX SCL/8
(This device was previously
referred to as the Avaya 146G)
· The between building connection must be via
earthed ducting, preferable underground. The cable
must not be exposed externally at any point.
Currently not supported.
132
Supports up to 4 two-wire lines.
(This device was previously
referred to as the Avaya 146C).
External Output Switch
· The IP Office expansion module and control unit
and IROB devices must be connected to the
protective ground point in their building.
For installations in the Republic of South Africa, the
fitting of surge protection on analog trunks is a
requirement.
For other locations where the risk of lightning strikes
is felt to be high, additional protection of incoming
analog trunks is recommended.
Connections from an IP Office Ext O/P port to an
external relay device must be via a surge protector.
The towerMAX range of devices are supplied by ITWLinx (http://www.itwlinx.com).
IP Office Standard Version Installation
IP Office 7.0
Page 131
15-601042 Issue 23e (16 March 2011)
6.7.1 DS Phones
When digital phone extensions are required in another building, additional In-Range Out-Of-Building (IROB) protective
equipment must be used. For phones connected to IP Office DS 376 ports, the supported device supplied by ITWLinx is a
towerMAX DS/2 module. This IROB device was previous badged by Avaya as the 146E IROB.
·
! WARNING
This device is not supported for TCM port connections, ie. 4100 Series, T-Series, 7400 Series and M-Series phones.
· Only DS connections on an external expansion module are supported. DS ports on cards in the control unit should
not be used.
The protection device should be installed as per the instructions supplied with the device. The ground points on the IP
Office control unit and the DS modules must be connected to a protective ground using 18AWG wire with a green and
yellow sleeve.
Typically the IROBs 2 RJ45 EQUIPMENT ports are straight through connected to the 2 RJ45 LINE ports. This allows existing
RJ45 structured cabling, using pins 4 and 5, to be used without rewiring for up to two DS connection. However each of
these ports can be used to connect a second extension using pins 3 and 6.
LINE
Signal
EQUIPMENT
1
Not used.
1
2
Not used.
2
3
Ring II (Optional)
3
4
Ring I
4
5
Tip I
5
6
Tip II (Optional)
6
7
Not used.
7
8
Not used.
8
IP Office Standard Version Installation
IP Office 7.0
Page 132
15-601042 Issue 23e (16 March 2011)
Additional Processes: Out of Building Telephone Installations
6.7.2 Analog Phone Barrier Box
Where analog phone extensions are required in another building, additional protective equipment must be used, in the
form of IP Office Phone Barrier Boxes and protective earth connections.
·
CAUTION
PHONE (POT) ports on the front of control units must not be used for extensions that are external to the main
building.
· The correct IP Office specific barrier boxes must be used. These modules have been designed specifically for the
signalling voltages used by the IP Office system:
· Only the IP Office Phone Barrier Box should be used with Phone V1 modules.
· Only the IP Office Phone Barrier Box V2 should be used with Phone V2 modules.
· No other type of analog phone barrier box should be used.
· Where more than 3 barrier boxes are required in a building, they must be rack mounted using a Barrier Box rack
mounting kit 134 .
· A maximum of 16 barrier boxes can be used with any Phone module.
· The Phone Barrier Box does not connect the ringing capacitor in Phone V1 modules.
Main Building
Barrier Box
· RJ11
Connect to PHONE (POT) port on the Phone
module using cable supplied with the barrier
box.
· RJ45
Connect to the secondary building barrier box
via primary protection in both buildings.
· Center Screw
Connect to main building protective ground
(or ground terminal of Barrier Box Rack
Mounting Kit). Use 18AWG (minimum) wire
with a green and yellow sleeve.
· Right-Hand Screw
Connect to ground point on Phone module
using ground cable supplied with barrier box.
1. The
·
·
·
Secondary Building
· RJ11
Connect to analog phone. Cable not
supplied.
· RJ45
From main building via primary
protection in both buildings.
· Center Screw
Connect to main building protective
ground. Use 18AWG (minimum) wire
with a green and yellow sleeve.
· Right-Hand Screw
Not used.
following wires must be kept apart, that is not routed in the same bundle:
Earth leads from the barrier box to the Phone modules.
Internal wires, for example extension leads going directly to the Phone modules.
Wires from external telephone going directly to the barrier boxes.
IP Office Barrier Boxes
SAP Code
IP400 Phone Barrier Box (81V)
Use with Phone V1 module. Includes an RJ45 to RJ11 cable and a
functional earth lead.
700293897
IP400 Phone Barrier Box V2 (101V)
Use with Phone V2 module. Includes an RJ45 to RJ11 cable and a
functional earth lead.
700385495
Barrier Box Rack Mounting Kit
700293905
IP Office Standard Version Installation
IP Office 7.0
Page 133
15-601042 Issue 23e (16 March 2011)
6.7.3 Rack Mounting Barrier Boxes
Where more than 3 Phone Barrier Boxes are used they must be rack mounted. The Barrier Box Rack Mounting Kit (SAP
Code 700293905) supports up to 8 Phone Barrier Boxes.
1. Unscrew the two screws arranged diagonally at the front of each barrier box and use these same screws to reattach
the barrier box to the rack mounting strip.
2. Each barrier box is supplied with a solid green ground wire connected to its functional ground screw. Remove and
discard this wire. Connect a green/yellow ground wire to the protective earth screw in the center of the Point on the
back of the Barrier Box.
3. The rack mounting strip has threaded M4 earthing pillars. Connect the other end of the barrier box ground wire,
using M4 washers and nuts, to the earthing pillar on that side of the rack mounting strip.
4. Using 14AWG wire with green and yellow sleeve, connect one of the earthing pillars to the buildings protective
earth.
5. Using 14AWG wire with green and yellow sleeve, connect the other earthing pillar to the Phone module.
6. Ensure that the following wires are not routed together in the same bundle:
· Earth lead from the barrier box to the Phone module.
· Internal wires, e.g. wires going directly to the Phone module.
· Wires from external telephone going directly to the barrier boxes.
IP Office Standard Version Installation
IP Office 7.0
Page 134
15-601042 Issue 23e (16 March 2011)
Additional Processes: Out of Building Telephone Installations
6.8 Using the External Output Port
All the IP Office control units are equipped with a EXT O/P port. The port is marked as EXT O/P and is located on the back
of the control unit adjacent to the power supply input socket.
The port can be used to control up to two external devices such as door entry relay switches. The usual application for
these switches is to activate relays on door entry systems. However, as long as the criteria for maximum current, voltage
and if necessary protection are met, the switches can be used for other applications.
The switches can be switched closed, open or pulsed (closed for 5 seconds and then open). This can be done in a number
of ways:
· Using IP Office short codes.
· Through the Door tab in Phone Manager Pro.
· Through the Door Release option in IP Office SoftConsole.
· Via the Open Door action in Voicemail Pro.
Default Short Codes
The following are the default short codes in the IP Office configuration for external output switch operation. They use the
short code features Relay On (closed), Relay Off (open) and Relay Pulse.
State
Switch 1
Switch 2
Closed
*39
*42
Open
*40
*43
Pulse
*41
*44
6.8.1 Port Connection
These ports are found on the rear of all IP Office control units. They are used for connection to external switching relays.
The port uses a standard 3.5mm stereo jack plug for connection.
The IP Office is able to open (high resistance), close (low resistance) or pulse (close for 5 seconds and then open) two
switches within the port. Either switch can be operated separately. These switches are intended for activation of external
relays in systems such as door opening systems.
· CAUTION: In installations where this port is connected to a device external to the building, connection must be via a
towerMAX SCL/8 Surge Protector and a protective ground connection must be provided on the IP Office control unit.
EXT O/P
Pin
Description
1
Switch 1.
2
Switch 2.
3
0 Volts (Ground/Chassis)
· Switching Capacity: 0.7A.
· Maximum Voltage: 55V d.c.
· On state resistance: 0.7 ohms.
· Short circuit current: 1A.
· Reverse circuit current capacity: 1.4A.
· Ensure that pins 1 and 2 are always at a positive voltage with respect to pin 3.
3.5mm stereo audio jack plugs are frequently sold as pre-wired sealed modules. It may be necessary to use a multi-meter
to determine the wiring connections from an available plug. Typically 3 (common to both relays) is the cable screen.
IP Office Standard Version Installation
IP Office 7.0
Page 135
15-601042 Issue 23e (16 March 2011)
6.9 So8 BRI Module
6.9.1 Example 1: ISDN Terminal
In this example, calls on DID 123456 are routed to the first port of the So8 expansion module. That port has been
configured as Line Group ID 701.
1. Configure an Incoming Call Routing
The destination is a short code that directs the call to the line group ID that contains the So lines. The Bearer
Capability has been set to Any, to allow data and voice via this route.
· Line Group ID: 0
· Incoming Number: 123456
· Destination: 123456
· Bearer Capability: Any
2.Create a System Short Code:
This is the destination used in the Incoming Call Route.
· Short Code: 123456
· Telephone Number: 123456
· Line Group ID: 701
· Feature: Dial
3. Send the configuration to the Control Unit.
Any call coming into the main system on DID 123456 will now be passed directly to the first port.
If you wish to assign DIDs from your main pool to individual ports and avoid network charges when dialing between them,
try variations on the following:
1. You have DID ranges, for example: 7325551000 to 7325551099. You wish to assign 7325551000-19 to port 1 and
7325551020-20 to port 2 etc.
2. Configure Incoming Call Route:
The # is used here instead of "n" to avoid problems with "Main". The minus sign means the number is processed from
the left and so will wait for the whole number.
· Line Group ID: 701
· Incoming Number: -100x
· Destination: #
3. Repeat for Line Group ID 702 etc.
4. Create Short codes, for example:
· Short Code: 100x
· Telephone Number: .
· Line Group ID: 701
· Feature: Dial
S0 calls dialed without the area code are handled locally without network charges. Calls with area calls will go via the
network.
IP Office Standard Version Installation
IP Office 7.0
Page 136
15-601042 Issue 23e (16 March 2011)
Additional Processes: So8 BRI Module
6.9.2 Example 2: Video Conference
In this example, calls are routed to a Polycom Viewstation module connected to a S0 port of the IP Office system.
The following settings were used on 4 incoming data channels of a PRI line:
· Line Number: 5
· Incoming Line Group: 95
· Channel Allocation: 23 -> 1
· Outgoing Line Group: 95
· Switch Type: 5ESS
· Direction: Bothway
· Line Sub Type: PRI
· Bearer: Data
· Provider: AT&T
· Service: Accunet (this is a important)
· Channels: 1-4
· Admin: In Service
To route an incoming video call on the PRI lines configured above to an SO8 module requires the following:
1. Create a dial short code that has the SO port as its destination Line Group. For this example the following was used:
· Short Code: 1500
· Number: .
· Feature: Dial
· Line Group: 601 (the SO8 port number)
2. Create an Incoming Call Routing that routes the appropriate calls to that short code. For this example the following was
used:
· Line Group: 95 (identifies calls using the PRI lines configured above)
· Destination: 1500 (the short code created above)
· Bearer: Any
To allow the video device on the S0 port to make outgoing calls to the PRI lines also requires a short code.
1. For this example the following was used:
· Code: 91N;
· Number: N
· Feature: Dial
· Line Group: 95
IP Office Standard Version Installation
IP Office 7.0
Page 137
15-601042 Issue 23e (16 March 2011)
Polycom Video Module Settings
The Polycom modules used in the previous example were the Viewstation 128, Viewstation 256 and Viewstation MP.
The Polycom module must have software that supports 'Standard ETSI ISDN' (European ISDN) and have its ISDN Switch
Protocol setting set to 'Standard ETSI Euro-ISDN'
The following were the settings used during testing:
Characteristics
Admin/Software and Hardware/Software
· Polycom View Station 512 MP.
· Software: 7.0.1.
· NTSC UIS Interface.
· Network Interface: S/T Interface.
· View Station PVS 1419.
· ISDN Version: IEUS v18:a00320
Admin/General Setup
Admin/Video Network/ISDN Video Network
· Country: USA
· Country Code: 1
· Language: English (USA)
· Area Code: 732
· Auto Answer: Yes
· Number A: blank
· AllowDial: Yes
· Number B: blank
· Allow User Setup: Yes
· ISDN Switch Protocol: Standard ETSI Euro-ISDN.
· Maximum Time on Call: 480.
User Setup
Admin/Video Network/IMUX
· Auto Answer: Yes
· Numbers: blank
· PIP: Auto
· SPID: blank
· Far Control of Near Camera: Yes
· Audio Quality: 168KB/s
· MP Mode: Auto
· Advanced Dialing: Dial Channels in Parallel
System Information
Admin/Software and Hardware/Hardware
· Release: 7.0.1
· Camera: NTSC
· Model: VS: 512
· Video Comm Interface: ISDN_Quad_BRI
· Network Interface Type: S/T Interface
Admin/Video Network
Admin/Video Network/Call Preference
· MultiPoint Setup: Auto
· ISDN Video Calls (H:320): Yes
IP Office Standard Version Installation
IP Office 7.0
Page 138
15-601042 Issue 23e (16 March 2011)
Additional Processes: So8 BRI Module
6.10 SNMP
SNMP (Simple Network Management Protocol) is a standard network protocol that allows the monitoring and management
of data devices across a network. An SNMP agent can be built into network devices such as routers and hubs. An SNMP
manager application, for example CastleRock or HP OpenView, can then communicate with those devices.
IP Office 2.0 and above supports SNMP communication. This communication can be:
· Polling:
Some SNMP applications (called "managers") send out polling messages to the network. They then record the
responds of any SNMP enabled devices (called "agents"). This allows the application to create a network map and to
raise an alarm when devices previously present do not respond.
· Most SNMP manager applications can also do simple IP address polling to locate non-SNMP enabled devices.
However this method of polling does not identify the device type or other information.
· SNMP polling including details about the responding device. For example an IP Office control unit's response
includes the control unit type, level of software, routing table information, up time, etc.
· Traps:
When certain events occur, a devices SNMP agent can send details of the event to the SNMP manager. This is called
an SNMP 'trap'. These appear in the event log of the SNMP manager. Most SNMP managers can be configured to
give additional alerts in response to particular traps.
· Management:
Some SNMP agents support device management and configuration changes through the SNMP manager interface.
This is not supported by IP Office.
IP Office SNMP operation has been tested against Castle Rock SNMPc-EE 5.1.6c and HP OpenView Network Node Manager
6.41.
What Information is Available Via SNMP
As described above, SNMP information can either be polled by the SNMP application or received as the result of the IP
Office sending SNMP trap information.
While the .mib files should not be edited, they can be read using a text editor and contain descriptions of all the various
information objects that can be polled or sent and the information tha each object will include. For a list of the .mib files,
see Installing the IP Office MIB Files 140 . The NOTIFICATION-TYPE objects are those used for SNMP traps 142 , the other
types of objects are those that can be polled 142 .
IP Office Standard Version Installation
IP Office 7.0
Page 139
15-601042 Issue 23e (16 March 2011)
6.10.1 Installing the IP Office MIB Files
To allow full communication between an SNMP agent and an SNMP manager, the SNMP manager must load MIB files
(Management Information Base) specific to the SNMP agent device and the features it supports. These MIB files contain
details of the information the agent can provide and the traps that it can send. Full details of the structure of the IP Office
MIB files, MIB groups within those files and event traps can be found in the "IP Office Installation Manual".
The MIB files for IP Office operation are included on the IP Office DVD in the folder \AdminCD\smnp_mibs. The actual
files required and the method of loading depend on the SNMP manager application being used. The details below cover the
two SNMP manager applications tested.
HP Open View Network Node Manager
1. Copy the following MIB files to the applications MIBs folder.
MIB File
Source
a.
rfc2737-entity-mib.mib
snmp_mibs\standard folder on OpenView Install CD.
b.
avayagen-mib.mib
\AdminCD\snmp_mibs\IPOffice folder on IP Office Admin DVD.
c.
ipo-prod-mib.mib
\AdminCD\snmp_mibs\IPOffice folder on IP Office Admin DVD.
d.
ipo-mib.mib
\AdminCD\snmp_mibs\IPOffice folder on IP Office Admin DVD.
e.
inet-address-mib.mib
\AdminCD\snmp_mibs\Standard folder on IP Office Admin DVD.
f.
rfc2213-integrated-services-mib.mib
\AdminCD\snmp_mibs\standard folder on OpenView Install CD.
g.
diffserv-dscp-tc.mib
\AdminCD\snmp_mibs\Standard folder on IP Office Admin DVD.
h.
diffserv-mib-hpov.mib
\AdminCD\snmp_mibs\Standard folder on IP Office Admin DVD.
i.
ipo-phones-mib.mib
\AdminCD\snmp_mibs\IPOffice folder on IP Office Admin DVD.
2. Start the OpenView Network Node Manager console.
3. Select Options and then Load/Unload MIBs: SNMP.
4. Select Load and select all the MIB files listed above.
5. Select Compile.
IP Office Standard Version Installation
IP Office 7.0
Page 140
15-601042 Issue 23e (16 March 2011)
Additional Processes: SNMP
CastleRock SNMPc 5.1.6c and earlier
1. Copy the following MIB files to the applications MIBs folder, normally C:\Program Files\SNMPc Network
Manager\mibfiles.
MIB file
Source
a.
ENTITY-MIB
\AdminCD\snmp_mibs\Standard on IP Office Admin DVD.
b.
AVAYAGEN-MIB.mib
\AdminCD\snmp_mibs\IPOffice on IP Office Admin DVD.
c.
IPO-PROD-MIB.mib
\AdminCD\snmp_mibs\IPOffice on IP Office Admin DVD.
d.
IPO-MIB.mib
\AdminCD\snmp_mibs\IPOffice on IP Office Admin DVD.
e.
INET-ADDRESS-MIB.mib
\AdminCD\snmp_mibs\Standard on IP Office Admin DVD.
f.
INTEGRATED-SERVICES-MIB
\AdminCD\snmp_mibs\Standard on IP Office Admin DVD.
g.
DIFFSERV-DSCP-TC.mib
\AdminCD\snmp_mibs\Standard on IP Office Admin DVD.
h.
DIFFSERV-MIB.mib
\AdminCD\snmp_mibs\Standard on IP Office Admin DVD.
i.
IPO-PHONES-MIB.mib
\AdminCD\snmp_mibs\IPOffice on IP Office Admin DVD.
2. In SMNPc select Config | MIB Database.
3. Select Add and select the MIB files listed above in the order listed.
CastleRock SNMPc V5.0.1
The MIB installation instructions provided above are correct for CastleRock SNMPc V5.0.8 and later. For V5.0.1 of
CastleRock SNMPc the following must be carried out:
1. Copy all of the IP Office MIBs and standard MIBs from the IP Office Administrator Applications DVD to the SNMPc
mibfiles directory.
2. In the SNMPc mibfiles directory open the files STANDARD.mib and SNMPv2-SMI.mib in Notepad.
3. In the SNMPv2-SMI.mib file find the definition of zeroDotZero and copy this to the clipboard.
4. In the STANDARD.MIB file find the SNMPv2-SMI section and paste in the definition of zeroDotZero from the
clipboard before the end of this section (just before the END statement).
5. Save the modified STANDARD.MIB file.
6. Add the MIB file SNMP-FRAMEWORK-MIB.mib to the MIB database using the instructions provided in the IP Office
installation guide.
7. Add all the MIB files listed in the instructions provided in the IP Office installation guide in the order given.
8. Compile the MIBs ready for use.
The reason for this is: The IPO-PHONES-MIB.mib relies upon the DIFFSERV-MIB.mib for the definition of the textual
convention of IndexInteger. The DIFFSERV-MIB needs the definition of the textual convention zeroDotZero which is
normally defined in SNMPv2-SMI.mib. However including SNMPv2-SMI.mib in the MIB file compilation list results in errors
due to conflicts with what appear to be internal definitions within SNMPc and the SNMPv2-SMI section in its STANDARD.
mib file. Therefore to resolve the issue the required definition of zeroDotZero must be placed in the SNMPv2-SMI section in
SNMPc's STANDARD.mib file.
IP Office Standard Version Installation
IP Office 7.0
Page 141
15-601042 Issue 23e (16 March 2011)
6.10.2 Enabling SNMP and Polling Support
In order for the IP Office control unit to be discovered and polled by an SNMP manager, its SNMP agent must be enabled
and placed in the same read community as the SNMP manager.
1. In Manager, receive the control unit's configuration.
2. Double-click System from the Configuration Tree panel and select the SNMP tab.
3. Tick SNMP Enabled.
4. In SNMP Port, enter the UDP port number used by the IP Office SNMP agent to listen for and respond to SNMP
traffic. The normal default is 161.
5. In Community (Read-only), enter the community to which the device belongs for read access. This community
name must match that used by the SNMP manager application when sending requests to the device. The
community public is frequently used to establish communication and then changed (at both the SNMP agent and
manager ends) for security.
6. Click OK.
7. Send the configuration back to the IP Office and select reboot.
8. Following the IP Office reboot, the SNMP manager should be able to discover the control unit.
9. The control unit's response will include details of the control unit type and the current level of core software.
6.10.3 Enabling SNMP Trap Sending
In Manager, receive the control unit's configuration.
1. Double-click System from the Configuration Tree panel and select the SNMP tab.
2. Ensure that SNMP Enabled is ticked.
3. Using either Trap Destination 1 or Trap Destination 2, enter the following information:
· Enter the IP Address of the PC running the SNMP manager application.
· Enter the Port on which the traps messages should be sent. This is the UDP port on which the IP Office sends
SNMP trap messages. The default is 162.
· Set the Community that will be used by the agent and the SNMP manager. The community public is frequently
used to establish communication and then changed (at both the SNMP agent and manager ends) for security.
4. Select the Events which should be sent:
· Generic:
Events such as soft reboot (warm start), hard reboot (cold start), links up/down (transition in the status of a
PPP or frame relay interface) or SNMP community mismatch.
· Entity:
Failures, errors and changes of state in IP Office modules and trunk interfaces. Note: Does not include ATM4.
· Licence:
Changes of state in the communication with the Feature Key Server.
· Phone Change:
Changes to the type of DS or IP phone connected to a port.
· Click on OK.
5. Send the configuration back to the IP Office and select reboot.
IP Office Standard Version Installation
IP Office 7.0
Page 142
15-601042 Issue 23e (16 March 2011)
Additional Processes: SNMP
6.11 Reset Button
The IP500 and IP500v2 control units have a Reset button. Pressing the button while the control unit is starting up will
pause the start up until the button is released. The effect of pressing the button during normal operation will depend on
how long the button is pressed and is indicated by the CPU LED.
Press Duration
(seconds)
CPU LED
Action
Summary
0 to 5.
Off
None
None.
5 to 10.
Orange
Reboot When Free
Reboot when free with new incoming/outgoing call
barring. A reboot using the reset button is recorded in
the Audit Trail.
10 to 30.
Flashing orange Erase Configuration/
Immediate Reboot
Erase the configuration, alarm log and audit trail.
Immediate reboot without waiting for active calls to end.
See Erasing the configuration 145 for full details.
30 to 40.
Red
Erase All.
Erase configuration, alarm log and core software. See
Erasing the Operational Software 148 for full details.
Over 40.
Flashing green
None
None.
6.12 AUX Button
IP500v2 control units have an AUX button. This button can be used as follows.
If pressed during a restart of the control unit, the control unit skip booting 155 from the /primary folder on the System
SD card. If pressed for more than 5 seconds when a system is running, the control unit will shutdown 117 for 10 minutes.
IP Office Standard Version Installation
IP Office 7.0
Page 143
15-601042 Issue 23e (16 March 2011)
6.13 DTE Port Maintenance
The DTE port on the back of IP Office control units is not normally used when configuring an IP Office system. However, in
extreme cases, the DTE port can be used to default the system's configuration or to erase it core software if necessary.
·
WARNING
Due to the nature of the actions in this section, they should only be performed if absolutely necessary to return a
system back to working order. In all cases, you must make every effort to ensure that you have a backup copy of
the system configuration.
· The DTE ports on IP Office expansion modules are not used for any maintenance or diagnostics.
6.13.1 DTE Port Settings
These ports are found on the rear of all IP Office control units and external expansion modules. The DTE ports on external
expansion modules are not used.
The RS232 DTE ports on the control units can be used for system maintenance and connection of serial terminal adaptors.
On IP400 control units the port can also be used for connection of the IP Office serial port licence key dongle.
An asynchronous terminal program such as HyperTerminal is also required. Configure this for operation via a PC serial
port, as follows:
Bits per second 38,400
Data bits 8
Parity None
Stop Bits 1
Flow Control None
Settings | Emulation TTY
DTE Cables
These cables are used for system maintenance and diagnostics under Avaya guidance. They can also be used for
connection of RS232 serial terminal adaptor equipment to the IP Office control unit. The cable required depends on the IP
Office control unit. This cable is a "Straight through DB9 female to DB9 male serial cable".
IP Office 9-Way RS232 Signal
DTE Port
PC/Terminal
Adaptor
3
Receive data
3
2
Transmit Data
2
7
RTS (Request To Send)
7
8
CTS (Clear To Send)
8
6
DSR (Data Set Ready)
6
5
Ground
5
1
DCD (Data Carrier Detect)
1
4
DTR (Data Terminal Ready)
4
9
RI (Ring Indicator)
9
IP Office Standard Version Installation
IP Office 7.0
Page 144
15-601042 Issue 23e (16 March 2011)
Additional Processes: DTE Port Maintenance
6.13.2 Erasing the Configuration
The following processes erases the configuration held in the IP Office control unit's memory. That include both the current
configuration being used in RAM memory and the backup configuration stored in non-volatile memory. Following this the
IP Office will restart with a default configuration.
This process should be performed from a PC with a fixed IP address, directly connected to the IP Office control unit and
with the IP Office system disconnected from any network. Following this process, the control unit's IP address will default
to 192.168.42.1.
·
Do not perform any of these processes unless absolutely necessary. The IP Office's configuration settings can
be default through Manager using the File | Advanced | Erase Configuration command.
· For IP Office Release 7.0 and higher, IP500v2 systems using IP Office A-Law or IP Office Mu-Law System SD
cards will default to IP Office Essential Edition - Quick Version mode. Loading the configuration will switch IP Office
Manager to simplified view. To change the system back to operating in IP Office Standard Version mode, select the
File | Advanced | Change Mode.
Erasing the Configuration via Debug
This process erases the IP Office's configuration settings but does not alter its security settings. It is easier to use than the
boot loader method.
1. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
a. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
b. Using IP Office Manager, select File | Open Configuration.
c. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
d. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
e. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
144 .
Within
b. Enter AT (note upper case). The control unit should respond OK.
c. Enter AT-DEBUG. The control unit should response with the time and date and then Hello> to show it is ready
to accept commands.
3. To erase the current configuration in RAM memory enter eraseconfig. The Hello> command prompt reappears
when the action is completed.
4. To erase the backup configuration stored in non-volatile Flash memory enter erasenvconfig. The Hello>
command prompt reappears when the action is completed.
5. To reboot the IP Office enter reboot. The IP Office will reboot and restart with a defaulted configuration.
6. Close the terminal program session.
7. Manager can now be used to alter and then upload an old configuration file or receive and edit the control unit's
now defaulted configuration.
IP Office Standard Version Installation
IP Office 7.0
Page 145
15-601042 Issue 23e (16 March 2011)
Erasing the Configuration and Security Settings via the Boot Loader
This process defaults the IP Office security settings and its configurations settings.
2. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
f. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
g. Using IP Office Manager, select File | Open Configuration.
h. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
i. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
j. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
144 .
Within
b. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same
time.
c. Switch off power to the IP Office control unit.
d. Power on the control unit and press the escape key every second until you get a Loader message. Below is an
example.
P12 Loader 2.4
CPU Revision 0x0900
e. Enter AT (note upper case). The control unit should respond OK.
f. If an OK response is not received, check the settings of your terminal program and repeat the process above.
3. Proceed with the erasure process.
· To erase the alarm log enter AT-X1.
· To erase the current configuration, enter AT-X2. A typical response if Sector 2 Erase (NV Config) followed
by OK. Enter AT-X3. A typical response is Sector Erases (Config) followed by a series of OK responses.
4. Switch power to the control unit off and then back on. Within the terminal program you should see various
messages as the control unit performs various start up tasks.
5. Close the terminal program session.
6. Manager can now be used to alter and then upload an old configuration file or receive and edit the control unit's
now defaulted configuration.
IP Office Standard Version Installation
IP Office 7.0
Page 146
15-601042 Issue 23e (16 March 2011)
Additional Processes: DTE Port Maintenance
6.13.3 Defaulting Security Settings
Procedure: Defaulting Security Settings
This process defaults the IP Office's security settings but does not alter its configuration settings.
1. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
2. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
HyperTerminal session, the current settings are summarized across the base of the screen.
144 .
Within a
3. Enter AT (note upper case). The control unit should respond OK.
4. Enter AT-SECURITYRESETALL.
5. You will be prompted to confirm the control unit's MAC address before continuing. Enter the address.
6. The control unit will respond OK when the action has been completed.
7. Close the terminal program session.
8. Manager can now be used to receive and edit the control unit's now defaulted security settings.
Defaulting the Configuration and Security Settings via the Boot Loader
This process defaults the IP Office security settings and its configurations settings.
1. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
a. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
b. Using IP Office Manager, select File | Open Configuration.
c. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
d. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
e. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
144 .
Within
b. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same
time.
c. Switch off power to the IP Office control unit.
d. Power on the control unit and press the escape key every second until you get a Loader message. Below is an
example.
P12 Loader 2.4
CPU Revision 0x0900
e. Enter AT (note upper case). The control unit should respond OK.
f. If an OK response is not received, check the settings of your terminal program and repeat the process above.
3. To erase the current configuration in RAM memory enter AT-X3. A typical response is Sector Erases (Config)
followed by a series of OK responses.
4. To erase the backup configuration stored in non-volatile memory enter AT-X2. A typical response if Sector 2
Erase (NV Config) followed by OK. IP Office 403 only: If running an IP Office 403 control unit, also enter AT-X4.
5. Switch power to the control unit off and then back on. Within the terminal program you should see various
messages as the control unit performs various start up tasks.
6. Close the terminal program session.
7. Manager can now be used to alter and then upload an old configuration file or receive and edit the control unit's
now defaulted configuration.
IP Office Standard Version Installation
IP Office 7.0
Page 147
15-601042 Issue 23e (16 March 2011)
6.13.4 Erasing the Operational Firmware
When the firmware loaded by the control unit is erased, the control unit will begin making BOOTP requests for a
replacement firmware file. Manager can act as a BOOTP server and respond to the control units request with the
appropriate file from those installed with Manager.
Unlike other control units, when the firmware loaded by an IP500v2 control unit is erased, the IP500v2 control unit will
first look for replacement firmware on its SD cards before falling back to using a BOOTP request to Manager.
The processes below should be performed from a PC with a fixed IP address, directly connected to the IP Office control
unit and with the IP Office system disconnected from any network. During the process, the control unit's IP address may
default to a value in the 192.168.42.1 to 192.168.42.10 range. If this occurs, it may be necessary to amend the BOOTP
entry in IP Office Manager to match the address the system is using.
·
Do not perform any of the following processes unless absolutely necessary. The IP Office software can normally
be upgraded using IP Office Manager 125 .
·
This process erases the operational software. Before attempting this process you must know the MAC and IP
addresses of the system, plus have a backup copy of its configuration and the correct .bin file for the control unit
type and level of software.
·
The presence of any firewall blocking TFTP and or BOOTP will cause this process to fail.
Erasing the Core Software via Debug
1. Run Manager.
· In the BOOTP entries, check that there is an entry that matches the MAC Address, IP Address and .bin file
used by the system. An entry is normally automatically created when a configuration has been loaded from
that IP Office. .
· If an entry is not present, create a new entry manually. The first two details can be found in the Control
Unit settings in the configuration file. Then close and restart Manager.
· Under File | Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP
Server is checked.
· Select View | TFTPLog.
· Check that the required .bin file is present in Manager's working directory.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
144 .
Within
b. Enter AT (note upper case). The control unit should respond OK.
c. Enter AT-DEBUG. The control unit should response with the time and date and then Hello> to show it is ready
to accept commands.
3. To erase the current configuration in RAM memory enter upgrade.
4. The IP Office will erase its current software and then send out a BootP request on the network for new software.
Manager will respond and start transferring the software using TFTP.
IP Office Standard Version Installation
IP Office 7.0
Page 148
15-601042 Issue 23e (16 March 2011)
Additional Processes: DTE Port Maintenance
Erasing the Core Software via the Boot Loader
2. Run Manager.
· In the BOOTP entries, check that there is an entry that matches the MAC Address, IP Address and .bin file
used by the system. An entry is normally automatically created when a configuration has been loaded from
that IP Office. .
· If an entry is not present, create a new entry manually. The first two details can be found in the Control
Unit settings in the configuration file. Then close and restart Manager.
· Under File | Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP
Server is checked.
· Select View | TFTPLog.
· Check that the required .bin file is present in Manager's working directory.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
144 .
Within
b. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same
time.
c. Switch off power to the IP Office control unit.
d. Power on the control unit and press the escape key every second until you get a Loader message. Below is an
example.
P12 Loader 2.4
CPU Revision 0x0900
e. Enter AT (note upper case). The control unit should respond OK.
f. If an OK response is not received, check the settings of your terminal program and repeat the process above.
3. Enter AT-X. The control unit should respond Multi-Sector Erase.
4. The control unit will now request the .bin file it requires. For IP500v2 control units this will be from files on the
System SD card. For other control units it will be from Manager and appears in the TFTP Log.
5. If the file transfers does not appear to be taking place, check that the IP address shown in the TFTP Log matches
the BOOTP entry. Adjust the BOOTP entry if necessary.
6. When completed the system will reboot.
IP Office Standard Version Installation
IP Office 7.0
Page 149
15-601042 Issue 23e (16 March 2011)
Chapter 7.
SD Card Management
IP Office Standard Version Installation
IP Office 7.0
Page 151
15-601042 Issue 23e (16 March 2011)
7. SD Card Management
The IP500v2 control unit has two SD card slots, labeled System SD and Optional SD respectively. These are used as
follows:
· System SD Card
An Avaya System SD card must be present in this slot at all times. This card holds copies of the IP Office firmware
and configuration and is used as the IP500v2 control units non-volatile memory.
· Each Avaya System SD card has a unique Feature Key serial number which is used for generating and
validating licenses entered into the IP Office configuration.
· The card stores the prompts for embedded voicemail operation and acts as the message store for embedded
voicemail messages.
· Prior to any planned shutdown or restart of the IP Office system, the current configuration running in the IP
Office system's RAM memory is copied to the /primary folder on the System SD card and to the systems nonvolatile memory.
· Following a restart, the software in the /primary folder is loaded by the IP500v2 control unit. If the required
software is not present or valid a sequence of fallback options is used, see Booting from the SD Cards 155 for
full details.
· Following a restart, if present, the configuration file in the /primary folder is loaded by the IP500v2 control
unit. If no file is present the system will check for a file in its internal non-volatile memory. If no copy is found
it will generate a default configuration file. See Booting from the SD Cards 155 for full details.
· Once each day (approximately between 00:00 and 00:30) the IP Office will copy the current configuration
running in its RAM memory to the /primary folder on the card.
· Configuration changes made using IP Office Manager are first written to the copy of the configuration file on
the card and then merged with the configuration running in the IP Office system's RAM memory.
· The write lock setting on cards in the System SD card slot is ignored.
· Optional SD Card
A card does not have to be present in this slot for normal IP Office operation. The slot can be used for various
maintenance actions.
· A card with an updated IP Office software or configuration can be inserted and those files then transferred to
the System SD card in order to upgrade the IP Office system.
· The full contents of the System SD card can be copied to the Optional SD card while the IP Office system is
running.
· The write lock setting on cards in the Optional SD card slot is honored.
Card
Removal
Memory cards should always be shutdown 167 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
IP Office Standard Version Installation
IP Office 7.0
Page 152
15-601042 Issue 23e (16 March 2011)
SD Card Management:
Card Maintenance Actions
Using IP Office Manager, IP Office System Status Application or a phone configured as a System Phone, a number of
actions can be performed on the SD cards.
Action
Description
Shutdown/
Restart 167
Memory cards should always be shutdown 167 before
being removed when the system is running. Though
the card slot LEDs indicate when data is being
written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will
disable embedded voicemail if being used. If the
System SD card is removed, features licensed by
the card's Feature Key serial number will continue
operating for up to 2 hours.
–
Backup
Copy the files in the /primary folder on the System
SD card to the /backup folder on the card.
6
Copy the files in the /backup folder on the System
SD card to the /primary folder on the card and
restart the IP Office system.
6
Restore
Copy
159
160
Manager
System
Status
System
Phone
Copy all the files on the System SD card to the
Optional SD card.
161
Upgrade
Binaries 164
Minutes
90
Copy software files in the /primary folder on the
Optional SD card to the /primary folder on the
System SD card and then restart the IP Office
system.
–
Copy the configuration file in the /primary folder on
the Optional SD card to the /primary folder on the
System SD card and then restart the IP Office
system.
–
–
5 seconds
Upload System
Files 164
Upload a set of IP Office software and embedded
voicemail prompts to the System SD card.
–
–
40
View Files
View the folders and files on the control unit memory
cards.
–
–
–
–
1
–
15
Upgrade
Configuration
158
164
5
The actions below can be performed on cards in a SD
card reader on a PC running IP Office Manager.
Format
157
Reformat a card for IP Office usage without removing
the Feature Key serial number.
·
Recreate
157
This process will erase all existing files on the
card.
Create the folder structure on a memory card and
copy a set of IP Office software files into those
folders.
–
·
IP Office Standard Version Installation
IP Office 7.0
Page 153
15-601042 Issue 23e (16 March 2011)
Card Specification
Non-Avaya cards can be used in the Optional SD slot as long as they match or exceed the standard below:
· SDHC 4GB minimum Class 2+. Single partition FAT32 format.
SD Card Folders
The System SD card contains the following folders:
· /primary
Contains the firmware files for the IP Office control unit, external expansion modules and
supported phones. The folder can also contain music on hold files and license key files. This is the
main set of files used by the IP Office system when booting up. Also contains the stored copy of
the IP Office configuration.
· /backup
Contains a copy of the primary folder at some previous point. A backup copy of the primary
contents to this folder can be invoked manually (using Manager or SSA) or as part of the IP Office
software upgrade using Manager.
· /lvmail
Contains the system prompts used by embedded voicemail. Note that the mailbox messages and
greetings are stored in a sub-folder of the /dynamic folder.
· The sub-folder /AAG is used to store embedded voicemail auto-attendant greetings.
· /doc
Contains initial installation documentation for IP Office and Avaya IP Office Essential Edition
Partner Version.
· /dynamic
Contains files used by the IP Office and retained through a reboot of the IP Office system.
· The sub-folder /lvmail is used to store individual user and group mailbox messages, name
recordings and announcements. The storage capacity for embedded voicemail is limited to 15
hours regardless of the capacity of the card.
· /temp
Contains temporary files used by the IP Office and not retained through a reboot of the IP Office
system.
The Optional SD card can contain a similar set of folders. These are used as an additional backup or they can be used as
the source for upgrading the contents of the System SD card.
IP Office Standard Version Installation
IP Office 7.0
Page 154
15-601042 Issue 23e (16 March 2011)
SD Card Management:
7.1 Booting from the SD Cards
When being powered up, the IP500v2 control unit looks for a valid ip500v2.bin
binary file to load. It does this using the possible source below in the order shown,
skipping to the next source if the file is not present or is not valid.
1. System SD card /primary folder.
2. The control unit's own internal non-volatile memory. Once a system has
been installed, it uses its non-volatile memory to keep copies of the
configuration and system binary files it is using. These can be used to
restore operation during a system reboot. Note that though a system can
boot from non-volatile memory, a System SD card must still be present for
correct system operation.
3. System SD card /backup folder.
4. Optional SD card /primary folder.
5. Optional SD card /backup folder.
6. If no file is found, the control unit will fallback to making BOOTP requests to
the network. IP Office Manager can respond the BOOTP request. See
Erasing the Operational Firmware 148 .
Once a valid ip500v2.bin file is found, the IP Office control unit will load that firmware. The source from which the control
unit binary file was loaded is then used to load further files.
Configuration File Loading
Having installed the necessary system firmware files as above, the IP500v2 control unit requires a configuration file:
· If the IP500v2 booted using binary files from an SD card location, it looks for a valid configuration file in the same
location.
· If a configuration file is present and valid, it is loaded.
· If a configuration file is present but is not valid, load the configuration copy in its non-volatile memory if
present, else it assumes a default configuration.
· If a configuration file is not present, use the non-volatile memory copy as above unless the reboot is as a result
of a default system command.
· If the IP500v2 booted using binary files from its non-volatile memory, it will also load the configuration copy from
that location.
· It will indicate a boot alarm (see below).
· It will attempt to restore the firmware file in the System SD card's /primary folder using the copy in its nonvolatile memory.
· The normal boot up process of upgrading expansion module firmware does not occur. If the File | Advanced |
Upgrade command is used, only external expansion modules actually present in the system are listed for
upgrade.
Post Boot Operation
During normal operation, configuration and binary files sent to the System SD card /primary folder using IP Office
Manager are also written to the non-volatile memory.
If the system has booted from its non-volatile memory due to an SD card problem, it is still possible to upgrade the
ip500v2.bin file using the IP Office upgrade wizard.
IP Office Standard Version Installation
IP Office 7.0
Page 155
15-601042 Issue 23e (16 March 2011)
Boot Alarms
The following apply if the IP500v2 boots using software other than that in its System SD /primary folder:
· An alarm will be shown in the System Status Application. It will also generate an alarm if the card in any slot is not
compatible. These alarms are also output as SNMP, Syslog or email alarms.
· The IP Office Manager Select IP Office menu will display an
icon indicating that the IP Office system is running
using software other than from the System SD card's primary folder.
· The configuration can be read but will be read only. Attempting to send a configuration to the system will cause the
error message Failed to save configuration data. (Internal error).
Bypassing the System SD Card Primary Folder
The control unit can be forced to bypass the System SD card's /primary folder and non-volatile memory when starting.
This is done by pressing the Aux button while applying power to the control unit.
This action may be necessary if, following an upgrade of the IP Office system, it is determined that a roll back to the
previously backed up firmware and configuration is required. Using the Aux button should restore system operation using
the /backup folder files while the installer then restores the contents of the /primary folder to a previous release.
IP Office Standard Version Installation
IP Office 7.0
Page 156
15-601042 Issue 23e (16 March 2011)
SD Card Management: Booting from the SD Cards
7.2 Creating an IP Office SD Card
The processes below can be applied to Avaya IP Office SD cards. They can also be applied to non-Avaya SD cards for use
in a system's Optional SD card slot.
The card must be the following format. For the System SD slot, only Avaya SD cards with a Feature Key should be used.
· SDHC 4GB minimum Class 2+. Single partition FAT32 format.
·
WARNING
Avaya supplied SD cards should not be formatted using any other method than the format commands within IP
Office Manager and IP Office System Status Application. Formatting the cards using any other method will remove
the feature key used for IP Office licensing from the card.
Creating a Card on a Local PC
These processes can be run on an SD card inserted in a card reader on the IP Office Manager PC. That card can then be
used in the System SD card slot of a new system or in the Optional SD card slot of an existing system to upgrade that
system 128 .
Formatting an SD Card
Avaya SD cards should only be formatted using the format options provided within IP Office applications. This process is
not normally necessary with Avaya SD cards unless you suspect that the card has been incorrectly formatted elsewhere.
·
WARNING: All File Will Be Erased
Note that this action will erase any existing files and folders on the card. Once a card has been formatted, the
folders and files required for IP Office operation can be loaded onto the card from the Manager PC using the
Recreate IP Office SD Card command.
1. Insert the SD card into a reader slot on the Manager computer.
2. Using IP Office Manager, select File | Advanced | Format IP Office SD Card.
3. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection just sets the card label
shown when viewing the card details. It does not affect the actual formatting. Select the label that matches the files
set you will be placing on the card.
4. Browse to the card location and click OK.
5. The status bar at the bottom of Manager will display the progress of the formatting process.
6. When the formatting is complete, you can use the Recreate IP Office SD Card command to load the IP Office
folders and files onto the card from the Manager PC.
Recreating an IP Office SD Card
This command can be used with a read-writeable SD card on the Manager PC. It copies the files and folders used by an
IP500v2 system when starting. It updates the card with the version of those files installed with the IP Office Manager
application. It includes the binary files for the IP500v2 system, external expansion modules and phones. It also includes
the prompt files for embedded voicemail operation.
This process just replaces existing files and adds new files. It does not delete files, so for example, any existing embedded
voicemail messages and greetings are retained. If the card contains dynamic system files such as SMDR records, they are
temporarily backed up by Manager and then restored after the card is recreated.
For the card to be used in an IP500v2 system's System SD slot the card must be Avaya SD Feature Key card. The card
must be correctly formatted, however a reformat of an existing working card is not necessary before using recreate to
update the card contents.
· The source for the files copied to the SD card are the sub-folders of the \Memory Cards folder under Manager's
Working Directory (normally C:\Program Files Avaya\IP Office\Manager). However, if the Working Directory
is changed to a location without an appropriate set of \Memory Cards sub-folders, the required set of files will not
be copied onto the SD card.
1. Once started do not interrupt this process, for example by removing the SD card. This process takes approximately
15 minutes.
2. Insert the SD card into a card reader on the Manager PC.
3. Using IP Office Manager, select File | Advanced | Recreate IP Office SD Card.
4. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection will affect how the IP
Office systems operates when defaulted with this card present in its System SD card slot. .
IP Office Standard Version Installation
IP Office 7.0
Page 157
15-601042 Issue 23e (16 March 2011)
5. Browse to the card location and click OK.
6. Manager will start creating folders on the SD card and copying the required files into those folders. This process will
take approximately 15 minutes.
7. Do not remove the SD card during the process. Wait until the Manager displays a message.
7.3 Viewing the Card Contents
Using IP Office Manager you can view the folders and files on the System SD card and the Optional SD card. You can then
use various commands to upload and download files to and from the cards.
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
IP Office Standard Version Installation
IP Office 7.0
Page 158
15-601042 Issue 23e (16 March 2011)
SD Card Management: Viewing the Card Contents
7.4 Backing Up the System SD Card
There are two levels of backup that can be performed.
· Backup the System SD Card Primary Folder 159
The contents of the primary folder on the card can be copied to the backup folder. They files can then be restored if
necessary. Both actions can be performed remotely.
· Backup the Whole System SD Card 161
The contents of the whole System SD card can be copied to the Optional SD card. While this can be done remotely,
the contents can only be copied back manually using a card reader.
The backup, restore and copy operations will not be performed if the destination card has insufficient space for the files
being copied.
7.4.1 Backing Up the Primary Folder
This process copies the contents of the /primary folder on the System SD card over the /backup folder. Any files with
matching file names will be replaced.
This takes approximately 6 minutes.
Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Backup System Files.
· The contents of the /primary folder on the System SD card will be copied to the /backup folder. This process
takes approximately 6 minutes.
Using the System Status Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Backup System Files.
· The contents of the /primary folder on the System SD card will be copied to the /backup folder. This process
takes approximately 6 minutes.
Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select System Backup.
· The contents of the /primary folder on the System SD card will be copied to the /backup folder. This process
takes approximately 6 minutes.
IP Office Standard Version Installation
IP Office 7.0
Page 159
15-601042 Issue 23e (16 March 2011)
7.4.2 Restore from the Backup Folder
The contents of the /backup folder on the System SD card can be copied to the /primary folder. Any files with matching
file names will be replaced. The IP Office is then restarted using the files now in the /primary folder.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Restore System Files.
· The contents of the /backup folder on the System SD card will be copied to the /primary folder. The process
takes approximately 6 minutes.
· When the process has been completed, the IP Office system will be restarted.
Using the System Status Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Restore System Files.
· The contents of the /backup folder on the System SD card will be copied to the /primary folder. The process
takes approximately 6 minutes.
· When the process has been completed, the IP Office system will be restarted.
Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select System Restore.
· The contents of the /backup folder on the System SD card will be copied to the /primary folder. The process
takes approximately 6 minutes.
· When the process has been completed, the IP Office system will be restarted.
IP Office Standard Version Installation
IP Office 7.0
Page 160
15-601042 Issue 23e (16 March 2011)
SD Card Management: Backing Up the System SD Card
7.4.3 Backing Up to the Optional Card
This process copies all files on the System SD card to the Optional SD card. It includes the /primary and /backup
folders and the embedded voicemail files including message files. Any matching files and folders on the Optional SD card
are overwritten.
The process is a simple copy. Any files already copied that change while the process are not recopied. Any new files added
(for example voicemail messages) while the process is running may not be copied.
This process takes at least 90 minutes and may take much longer depending on the amount of data to be copied, for
example it will be longer if embedded voicemail is being used by the IP Office system to take messages.
Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Copy System Card.
· The contents of the System SD card will be copied to the Optional SD card. This process at least 90 minutes
and can take much longer.
Using the System Status Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select System Card.
5. At the bottom of the screen select Copy System Card.
· The contents of the System SD card will be copied to the Optional SD card. This process at least 90 minutes
and can take much longer.
Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select Copy.
· The contents of the System SD card will be copied to the Optional SD card. This process at least 90 minutes
and can take much longer.
IP Office Standard Version Installation
IP Office 7.0
Page 161
15-601042 Issue 23e (16 March 2011)
7.4.4 Restoring from the Optional Card
The files in the /primary folder on the Optional SD card can be copied to the /primary folder on the System SD card.
Any files with matching file names will be replaced. The IP Office is then restarted using the files now in the System SD
card's /primary folder.
The restore process is separated into two parts, either copying configuration files from the Optional SD card or copying
software files from the Optional SD card. This allows software files to be copied from an Optional SD card without affecting
the existing configuration of that system.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
7.4.4.1 Restoring a Configuration from an Optional Card
The following processes copy the configuration file (config.cfg) and licenses file (keys.txt). The processes take a few
seconds.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Copying a Configuration from the Optional SD Card File Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Upgrade Configuration.
· The configuration file (config.cfg) and licenses file (keys.txt) in the /primary folder on the Optional SD card
are copied to the /primary folder on the System SD card. This process takes approximately a few seconds.
· When the process has been completed, the IP Office system will be restarted.
Copying a Configuration File from the Optional SD Card Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select Upgrade Config....
· The configuration file (config.cfg) and licenses file (keys.txt) in the /primary folder on the Optional SD card
are copied to the /primary folder on the System SD card. This process takes approximately a few seconds.
· When the process has been completed, the IP Office system will be restarted.
IP Office Standard Version Installation
IP Office 7.0
Page 162
15-601042 Issue 23e (16 March 2011)
SD Card Management: Backing Up the System SD Card
7.4.4.2 Restoring Software from an Optional SD Card
These processes copy all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt). The
processes take approximately 5 minutes. These process do not restore embedded voicemail prompts (see Upgrading Card
Software 164 ).
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Copying Software Files from the Optional SD Card Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Upgrade Binaries.
· The software files (all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt))
in the /primary folder on the Optional SD card are copied to the /primary folder on the System SD card. This
process takes approximately 5 minutes.
· When the process has been completed, the IP Office system will be restarted.
Copying Software Files from the Optional SD Card Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select Upgrade Binaries....
· The software files (all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt))
in the /primary folder on the Optional SD card are copied to the /primary folder on the System SD card. This
process takes approximately 5 minutes.
· When the process has been completed, the IP Office system will be restarted.
IP Office Standard Version Installation
IP Office 7.0
Page 163
15-601042 Issue 23e (16 March 2011)
7.5 Upgrading Card Software
In addition to using the traditional IP Office Upgrade Wizard 126 , IP500v2 control units can be upgraded by loading the
required set of firmware files onto the System SD card and rebooting the system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
There are a number of ways in which this can be done.
Method
Using Manager
165
System SD Card
Upgrade 165
Upgrade from
Optional SD Card
166
Description
Location
Using IP Office Manager, the contents of the card are
compared to the files that Manager has available and
are upgraded if necessary.
Local or
Remote
In this method, the System SD card is shut down and
removed from the control unit. The card's contents are
upgraded using IP Office Manager.
Local
This method uses an SD card loaded with the required
version of IP Office software. The card is inserted into
the control unit's Option SD card slot and its contents
copied to the System SD card.
Local
IP Office Standard Version Installation
IP Office 7.0
Software
Files
Embedded
Voicemail
Prompts
–
Page 164
15-601042 Issue 23e (16 March 2011)
SD Card Management: Upgrading Card Software
7.5.1 Upgrading Remotely Using Manager
This process will copy all system files not present or of a different version compared to those already present on the
System SD card. That includes IP Office software files and embedded voicemail prompt files.
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Backup System Files. The contents of the /primary folder on the System SD card will be copied to
the /backup folder. This process takes approximately 6 minutes.
5. Select File | Upload System Files. The system files that Manager has will be uploaded to the /primary folder on
the System SD card. This includes IP Office software files and embedded voicemail prompt files. Depending on the
files that need to be updated, this process can take up to 40 minutes.
7.5.2 Upgrading the SD Card Locally
The following process can be used if you have physical access to the IP500v2 control unit. This method be used with a
timed reboot, allowing the card upgrade to be done during normal operation hours followed by a reboot outside of normal
operation hours.
If the card is being used for embedded voicemail, that service is not available while the card is shutdown. Licensed
features however will continue running for up to 2 hours while the card is shutdown.
1. Shutdown the System SD memory card
167
and remove it from the control unit.
2. Follow the process for recreating the SD card 157 . This process will overwrite the software files on the card with the
files available to IP Office Manager. It will not affect any other files, for example the configuration file and
embedded voicemail mesages. This process takes approximately 15 minutes.
3. When the recreate process has completed, reinsert the card into the control unit's System SD card slot.
4. Using IP Office Manager select File | Advanced | Reboot.
5. In the Select IP Office menu, select the IP500v2 system and click OK.
6. Select the type of reboot that you want performed and click OK.
7. When the system is rebooted, as it restarts it will load the software files in the primary folder of the System SD
card.
IP Office Standard Version Installation
IP Office 7.0
Page 165
15-601042 Issue 23e (16 March 2011)
7.5.3 Upgrading Using an Optional SD Card
This method allows an Optional SD card to be used as the source from which the System SD card is upgraded. It only
upgrades the software files, it does not update embedded voicemail prompts.
1. Once started do not interrupt this process, for example by removing the SD card. This process takes approximately
15 minutes.
2. Insert the SD card into a card reader on the Manager PC.
3. Using IP Office Manager, select File | Advanced | Recreate IP Office SD Card.
4. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection will affect how the IP
Office systems operates when defaulted with this card present in its System SD card slot. .
5. Browse to the card location and click OK.
6. Manager will start creating folders on the SD card and copying the required files into those folders. This process will
take approximately 15 minutes.
7. Do not remove the SD card during the process. Wait until the Manager displays a message.
7. Insert the card into the control unit's Optional SD card slot.
8. Use one of the processes below to copy the software from the Optional SD card to the System SD card. Each of
those processes will cause the IP Office system to be restarted.
Copying Software Files from the Optional SD Card Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Upgrade Binaries.
· The software files (all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt))
in the /primary folder on the Optional SD card are copied to the /primary folder on the System SD card. This
process takes approximately 5 minutes.
· When the process has been completed, the IP Office system will be restarted.
Copying Software Files from the Optional SD Card Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select Upgrade Binaries....
· The software files (all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt))
in the /primary folder on the Optional SD card are copied to the /primary folder on the System SD card. This
process takes approximately 5 minutes.
· When the process has been completed, the IP Office system will be restarted.
IP Office Standard Version Installation
IP Office 7.0
Page 166
15-601042 Issue 23e (16 March 2011)
SD Card Management: Upgrading Card Software
7.6 Removing SD Cards
Card
Removal
Memory cards should always be shutdown 167 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
The following processes can be used with SD cards installed in IP500v2 control units and also with Compact Flash memory
cards installed in IP406 V2 control units.
7.6.1 Card Shutdown
Card
Removal
Memory cards should always be shutdown 167 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
Before a memory card is removed from an IP Office system that is running, the card must be shutdown. Removing a
memory card while the system is running may cause file corruption.
Card services can be restarted by either reinserting the card or using a Start Up command.
Card Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Shutdown.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
Card Shutdown Using the System Status Application Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Shutdown.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
Card Shutdown Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select System for the System SD card or Option for the Optional SD card.
5. Select Shutdown.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
IP Office Standard Version Installation
IP Office 7.0
Page 167
15-601042 Issue 23e (16 March 2011)
7.6.2 Card Startup
Reinserting a memory card into a system that is already switched on will automatically restart card operation. However, if
the card has been shutdown but not removed, it can be restarted using Manager without requiring a reboot.
Card Startup Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Startup.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
Card Startup Using the System Status Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Start Up.
Card Startup Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400, 5600
or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to restrict access to
system administration functions on the phone.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select Memory Card.
4. Select System for the System SD card or Option for the Optional SD card.
5. Select Startup.
IP Office Standard Version Installation
IP Office 7.0
Page 168
15-601042 Issue 23e (16 March 2011)
SD Card Management: Removing SD Cards
7.6.3 System Shutdown
IP Office systems running IP Office Release 6 can be shut down in order to perform maintenance. The shut down can be
either indefinite or for a set period of time after which the IP Office will automatically reboot.
During the shut down process, the current configuration in the control unit's RAM memory is copied to the control units
non-volatile memory. For IP500v2 systems that location is the System SD card.
For control units with memory cards the memory cards can be shutdown and restarted
167
separately from the system.
! WARNINGS
· A shutdown must always be used to switch off the system. Simply removing the power cord or switching off the
power input may cause errors.
· This is not a polite shutdown, any users calls and services in operation will be stopped. Once shutdown, the system
cannot be used to make or receive any calls until restarted.
· The shutdown process takes up to a minute to complete. When shutdown, the CPU LED and the IP500 base card
LEDs 1 and 9 (if trunk daughter card fitted) will flash red rapidly. The memory card LEDs are extinguished. Do not
remove power from the system or remove any of the memory cards until the system is in the this state.
· To restart a system when shutdown indefinitely, or to restart a system before the timed restart, switch power to
the system off and on again.
System Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | System Shutdown.
2. Using the Select IP Office menu, the System Shutdown Mode menu is displayed.
3. Select the type of shutdown required. If Indefinite is used, the system can only be restarted by having its power
switched off and then on again. If a Timed shutdown is selected, the IP Office will reboot after the set time has
elapsed.
System Shutdown Using the System Status Application
1. Start System Status
67
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Shutdown System.
4. Select the time duration for the shutdown or indefinite.
IP Office Standard Version Installation
IP Office 7.0
Page 169
15-601042 Issue 23e (16 March 2011)
System Shutdown Using a System Phone
This process can be used by a user configured as a System Phone user and using a 1400, 1600, 2400, 4600, 5400,
5600, 9400, 9500 or 9600 Series phone (excluding XX01, XX02 and XX03 models). The user's Login Code is used to
restrict access to system administration functions on the phone.
Unlike Manager, a system phone user cannot select an indefinite shutdown. They can set a timed shut down of between 5
minutes and 24 hours.
1. Select Features | Phone User | System Admin.
2. Enter your IP Office user login code.
3. From the menu select System Shutdown.
4. Select a time period for the shutdown. It must be in between 5 minutes and 24 hours.
5. Press Done and then Confirm to begin the shutdown.
System Shutdown Using the IP500v2 AUX Button
When the AUX button is pressed for more than 5 seconds, the IP500v2 control unit will shutdown with the restart timer
set to 10 minutes.
IP Office Standard Version Installation
IP Office 7.0
Page 170
15-601042 Issue 23e (16 March 2011)
Chapter 8.
IP500 Basic Installation
IP Office Standard Version Installation
IP Office 7.0
Page 171
15-601042 Issue 23e (16 March 2011)
8. IP500 Basic Installation
8.1 IP500 Tools Required
The following is a general summary of the tools required. Additional tools and equipment will be
required for wall and or rack mounting and to fashion ground cable connections suitable to local
requirements.
· Tools Required
· o 5mm Flat-blade screwdriver.
· o Crosshead screwdriver.
· o Anti-static wrist strap and ground point.
· o RJ45-RJ45 Ethernet LAN Cable.
· o M4 Cross-Head Screwdriver.
· o Tools suitable for crimping a cable spade.
· o If wall mounting, drills and tools for wall mounting fixtures.
· Additional Parts Required
In addition to orderable IP Office equipment, the following items will be required.
· o 14AWG Solid copper wire for ground connection of control units and expansion modules.
· o Cable sleeve matching local regulator requirements for ground wires. Typically green for a functional ground
and green/yellow for a protective ground.
· o If wall mounting, additional fixtures and fittings suitable for the wall type and mounting kit being used.
· o Cable ties and labels for tidying and identifying cables.
IP Office Standard Version Installation
IP Office 7.0
Page 172
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: IP500 Tools Required
8.2 IP500 Read the Documentation
Ensure that you have read this manual in full before starting installation. Also include the
installation documentation for any other equipment and applications being installed as part
of the IP Office system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
· Partner Version Installation
· Compact DECT Installation.
· one-X Portal for IP Office Installation
· IP DECT R4 Installation.
· 4600/5600 Series IP Phone Installation.
· 3600 Series Wireless IP Installation.
· Embedded Voicemail Installation.
· Phone Manager Installation Manual.
· Voicemail Pro Installation.
· SoftConsole Installation Manual.
· Contact Store Installation.
· SIP Extension Configuration
Information Web Sites
IP Office documentation is available from the following web sites.
· Avaya Support (http://support.avaya.com)
Contains documentation and other support materials for Avaya products including IP Office. Copies of the IP Office
CD images are available from this site and updated core software .bin files.
· Avaya IP Office Knowledge Base (http://marketingtools.avaya.com/knowledgebase)
Access to an on-line regularly updated version of the IP Office Knowledge Base.
IP Office Standard Version Installation
IP Office 7.0
Page 173
15-601042 Issue 23e (16 March 2011)
8.3 IP500 Unpacking
Use the following procedure when unpacking any equipment supplied by
Avaya or an Avaya reseller or distributor.
Information Required
· o Equipment Checklist.
An installation checklist of the parts and equipment ordered for the
installation.
Procedure
1. o Check for Packaging Damage
Before unpacking any equipment, check for any signs of damage that may have occurred during transit. If any
damage exists bring it to the attention of the carrier.
2. o Check the Correct Parts Have Been Delivered
Check all cartons against the packing slip and ensure that you have the correct items. Report any errors or
omissions to the equipment supplier.
3. o Retain All Packaging and Documentation
While unpacking the equipment, retain all the packaging material. Fault returns are accepted only if repackaged in
the original packaging. If performing a staged installation, the original packaging will also assist when repacking
equipment to be moved to the final install site.
4. o Ensure that Anti-Static Protection Measures are Observed
Ensure that anti-static protection measures are observed at all times when handling equipment with exposed
electrical circuit boards.
5. o Check All Parts
Visually inspect each item and check that all the necessary documentation and accessory items have been included.
Report any errors or omissions to the dealer who supplied the equipment.
6. o Check All Documentation
Ensure that you read and retain any documentation included with the equipment.
IP Office Standard Version Installation
IP Office 7.0
Page 174
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: IP500 Unpacking
8.4 IP500 Card Installation
The IP500 base cards and trunk daughter cards should be fitted before power
is applied to the control unit.
1. Fitting IP500 Trunk Daughter Cards to the Base Cards.
2. Fitting IP400 Legacy Cards to a Legacy Card Carrier.
3. Installing IP500 Cards into the Control Unit.
·
176
177
178
Warnings
· Correct anti-static protection steps should be taken before handling circuit boards.
· Cards must never be added or removed from the control unit while it has power connected.
· General Notes
· Cards can be fitted in any order into any available slots. The only exception is the IP500 4-Port Expansion card
which can only be installed in right hand slot 4.
· For phone based administration, the card in slot 1 must be able to support ETR 18D, ETR 34D, M7324, M7310,
T7316E, T7316, 1408 or 1416 phones. Phone based administration is not supported in IP Office Standard
Version mode.
· It is recommended that cards are fitted from left to right.
· There are restrictions to the number of supported cards of some types. When such a limit is exceed, the rightmost card of that type will not function.
· Ensure that you use the labels supplied to identify the card fitted into the control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 175
15-601042 Issue 23e (16 March 2011)
8.4.1 IP500 Daughter Card Preparation
IP500 trunk daughter cards can be fitted to any IP500 base card except the IP500 Legacy Card Carrier. For IP500
Combination cards, the trunk daughter card is pre-installed and cannot be changed.
Warnings
1. Correct anti-static protection steps should be taken while handling
circuit boards.
Parts and Equipment Required
1. o IP500 Base Card (except the IP500 Legacy Card Carrier).
2. o IP500 Trunk Daughter Card
3. o 3 Stand Off Pillars
These are supplied with the trunk daughter card.
Tools Required.
1. o 5mm Flat-blade screwdriver.
2. o Anti-static wrist strap and ground point.
Procedure: Installing a Trunk Daughter Card
1. Check that correct cards have been supplied.
2. Ensure that you are wearing an anti-static wrist strap connected
to a suitable ground point.
3. On the base card identify the position of 3 holes for the plastic
pillars for the IP500 card. These are along the same edge as the
card connector.
4. Fit the stand off pillars to the IP500 base card.
5. If there is a clip-on metal shield over the connector block on the
base card, remove it.
6. Using minimal force and checking that the pins are correctly
located, push the IP500 trunk card onto its connector block and
the stand off pillars.
7. Check that the card connector has snapped into position.
8. Using the washers and screws provided, secure the metal stand
off pillars to the base card.
9. A set of labels are supplied with the trunk daughter card. Fit the
appropriate label to the front of the base card.
IP Office Standard Version Installation
IP Office 7.0
Page 176
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: IP500 Card Installation
8.4.2 IP500 Legacy Card Preparation
An IP500 Legacy Carrier card can be used to fit IP400 trunk or VCM cards into an IP500 or IP500v2 control unit. Up to 2
IP500 legacy carrier cards can be inserted.
PRI T1
Dual PRI T1
PRI 30 E1 (1.4)
Dual PRI E1
PRI 30 E1R2 RJ45
Dual PRI E1R2 RJ45
BRI-8 (UNI)
ANLG 4 Uni (US only)
VCM
VCM
VCM
VCM
VCM
4
8
16
24
30
Warnings
1. Correct anti-static protection steps should be taken while handling
circuit boards.
Parts and Equipment Required
1. o IP500 Carrier Card
2. o IP400 Card
The table opposite lists supported cards. Any card not listed is not
supported. Cards are supplied with 2 plastic stand off pillars. Trunk
cards are also supplied with a replacement blanking plate which is
not required.
Tools Required
1. o 5mm Flat-blade screwdriver.
2. o Anti-static wrist strap and ground point.
Procedure: Installing a Carrier Card
1. Check that correct cards have been supplied.
2. Ensure that you are wearing an anti-static wrist strap connected to
a suitable ground point.
3. On the carrier card identify the position of the jumper block and
stand off pillar holes for the IP400 card. The peg holes are labeled
as VCM or TRUNK.
4. If fitting an IP400 trunk card, identify which of the plastic snap-off
panels on the front of the carrier card need to be removed to allow
the trunk cable connections. Carefully remove those panels.
5. Fit the stand off pillars to the IP500 carrier card.
6. Using minimal force and checking that the pins are correctly
located, push the IP400 card onto its jumper and the stand off
pillars.
IP Office Standard Version Installation
IP Office 7.0
Page 177
15-601042 Issue 23e (16 March 2011)
8.4.3 IP500 Card Insertion
Having prepared each IP500 base card by adding any trunk daughter card
be inserted into the control unit.
·
176
or IP400 legacy card
177 ,
the base card can
Warnings
· Correct anti-static protection steps should be taken while handling circuit boards.
· Cards must never be added or removed from the control unit while it has power connected.
· Tools Required
· o 5mm Flat-blade screwdriver.
· o Anti-static wrist strap and ground point.
Installing an IP500 Card
1. Check that there is no power to the control unit.
2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for
each card being installed. This cover is no longer required but should be retained until installation has been
completed.
3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit. When half inserted,
check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates remove it
and begin inserting it again.
4. The card should slide in freely until almost fully inserted. At this point apply pressure at the base of the front of the
card to complete insertion.
5. Using a flat-bladed screwdriver secure the card.
6. Reapply power to the control unit. Initially each card should show a red LED (two if a daughter card is fitted) as the
control unit restarts. After approximately 30 seconds these should change to flashing red as the card is started.
These should then change to flashing every 5 seconds if the cards have started correctly.
7. Run the IP Office System Status Application and verify that the cards have all been recognized.
8. IP Office Manager can now be used to configure the extensions and trunk lines. For any IP500 VCM base cards, VCM
Channel licenses must be added to the configuration to enable channels above the base 4.
IP Office Standard Version Installation
IP Office 7.0
Page 178
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: IP500 Card Installation
8.5 Inserting the Feature Key
The IP500 uses a smart card feature key dongle. In addition to feature licensing the IP500
control unit uses this feature key dongle to determine various systems defaults such as A-Law or
Mu-Law operation, default short codes and trunk settings.
Warnings
1. The feature key is required for all IP500 control units and must be present when the system is
started and during operation. This applies even if the IP500 is not using any licensed features.
2. The feature key slot cover must remain present to protect the card and the card reader from
damage.
3. Correct anti-static protection steps should be taken before handling circuit boards.
4. During this process power to the IP Office control unit must be switched off and disconnected.
Parts Required
· IP500 Feature Key
The correct key will depend on the locale. The listing below is typical and may not apply in all cases. Ensure that
the serial number of the key, shown on the card, is recorded.
· o Mu-Law: Used in North America and Korea.
· o A-Law: Used in all other locales.
Tools Required:
· o 5mm Flat-blade screwdriver.
Procedure
1. Locate the feature key slot on the rear of the IP500 control unit. The slot is adjacent to the power input socket and
is protected by a metal cover.
2. Undo the screws on the cover until it can be rotated clear of the feature key card slot.
3. Insert the feature key. The card should be face up and inserted in the direction of the arrow on the card.
4. Rotate the slot cover back into position and tighten the screws.
IP Office Standard Version Installation
IP Office 7.0
Page 179
15-601042 Issue 23e (16 March 2011)
8.6 Applying Power
This procedure starts a new IP Office control unit not connected to any LAN. In this
scenario the IP Office control unit will assume its default configuration settings.
Objective - To power up the IP Office control unit to a known state with a
known set of defaults.
Warnings
1. When powering up the control unit for the first time do not connect the LAN port
or WAN port of the control unit to any network.
2. The power cord must be connected directly from the control unit to the switched
power outlet socket. The cord must not be fixed in anyway or routed through
any permanent structure.
Parts and Equipment Required
· o Switched power outlet socket.
· o IP Office Control Unit.
· o Locale Specific Power Cord.
Procedure
1. Connect the power cord from the power supply outlet to the power input socket on the rear of the control unit.
· Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar
openings. Installation measures must be taken to prevent physical damage to the power supply cord, including
proper routing of the power supply cord and provision of a socket outlet near the fixed equipment or
positioning of the equipment near a socket outlet.
2. Switch on power to the control unit.
3. New IP Office 500 control units are supplied with a base software level of 4.0.0. The CPU LED on these units will
flash red until the unit is upgraded to the required level of released IP Office core software.
4. The CPU LED on units that have already been upgraded from 4.0.0 will go through a green red cycle several times
and then stay green on. During this time other LEDs may flash as the unit goes through its power on self test cycle.
IP Office Standard Version Installation
IP Office 7.0
Page 180
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Applying Power
The following are the basic default configuration settings for an IP Office system.
Network Settings
LAN1
LAN2/WAN
IP address
192.168.42.1.
192.168.43.1
IP Mask
255.255.255.0
255.255.255.0
DHCP Mode
Server
Server
No of DHCP IP Addresses
200.
200.
· Extensions and Users
A user is automatically created for each physical extension port detected in the system. Users are assigned
extension numbers starting from 201. User names take the form Extn201, Extn202, ....
· Hunt Group
A single hunt group 200 called Main is created and the first 10 users are placed into that hunt group as members.
· Incoming Call Routes
Two default incoming call routes are created. Voice calls are routed to the hunt group Main. Data calls are routed to
the RAS user DialIn.
· Default Short Codes
IP400 control units are manufactured as either A-Law or U-Law variants. For IP500 and IP500v2 control units, ALaw or U-Law variant operation is determined by the Feature Key installed in the control unit. Depending on the
variant, different short codes and trunk settings are added to the default configuration.
· A-Law or Mu-Law
PCM (Pulse Code Modulation) is a method for encoding voice as data. In telephony, two methods PCM encoding are
widely used, A-law and Mu-law (also called U-law). Typically Mu-law is used in North America and a few other
locations while A-law by the rest of the world. As well as setting the correct PCM encoding for the region, the A-Law
or Mu-Law setting of an IP Office system when it is first started affects a wide range of regional defaults relating to
line settings and other values.
· For IP400 IP Office systems, each control units was manufactured as either an A-Law variant or a Mu-Law
variant.
· For IP500 and IP500v2 systems, the encoding default is set by the type of Feature Key installed when the
system is first started.
Default DHCP/IP Address Settings
When a defaulted or new IP Office control unit is switched on, it requests IP address information from a DHCP Server on
the network. This operation will occur whether the LAN cable is plugged in or not. The process below is done separately for
both the LAN port (LAN1 in the configuration) and the WAN port (LAN2 in the configuration) on the back of the IP Office
control unit.
· The IP Office makes a DHCP request for what IP address information it should use.
· If a DHCP server responds within approximately 10 seconds, the control unit defaults to being a DHCP client and
uses the IP address information supplied by the DHCP server.
· If no DHCP Server responds, the control unit still defaults to being the DHCP client but assumes the following
default addresses:
· LAN1: 192.168.42.1/255.255.255.0.
· LAN2: 192.168.43.1/255.255.255.0.
· Note that the IP Office does not check that these addresses are valid and or available on the network.
· Systems running in IP Office Standard Version mode can also be configured as a DHCP server. They can also be
configured to only provide DHCP for Avaya IP phones and or for remote access dial-in connections. DHCP Server
options are not supported for systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential
Edition - Norstar Version and IP Office Essential Edition - Quick Version modes.
·
! Once an IP500v2 control unit has obtained IP address and DHCP mode settings, it will retain those settings even
if rebooted without a configuration file present on the System SD card. To fully remove the existing IP address and
DHCP mode setting the IP Office must be defaulted using IP Office Manager.
IP Office Standard Version Installation
IP Office 7.0
Page 181
15-601042 Issue 23e (16 March 2011)
8.7 Check the CPU LED
During normal operation, the CPU LED on the rear of the IP500 control unit
should be green.
· Note
New IP Office 500 control units are supplied with a base software level
of 4.0.0. The CPU LED on these units will flash red until the unit is
upgraded to the required level of released IP Office core software.
Normal Power On Sequence
When power to the control unit is switched on, the normal sequence for the
CPU LED is as follows.
1. Steady Red for 3 seconds
2. Off for 10 seconds
3. Flashing alternate red/green for 4 seconds.
4. The LED should be steady green following successful start up. Note that
the IP500 cards on the front of the control unit may still be going
through their own start up process.
· Flashing RED
A flashing red CPU LED at this stage indicates an error. The most
likely cause is a missing Feature Key card.
IP Office Standard Version Installation
IP Office 7.0
Page 182
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Check the CPU LED
8.8 Upgrading the Core Software
New IP500 control units are supplied with a basic level of software (4.0.0). That
software is sufficient to allow LAN network connect to the control unit in order to
then upgrade it to the level of IP Office software required.
Objective - Upgrade the control unit to IP Office 4.0 software.
Information Required
· o System Password - For a new or defaulted system this is password.
Tools Required
· o Manager PC - The Upgrade Wizard tool is part of the Manager
application.
WARNINGS
· Check IP Office Technical Bulletins
Check the latest IP Office Technical Bulletin for the IP Office software release before proceeding any further. It may
contain information relating to changes that occurred after this document was completed. Bulletins are available
from http://support.avaya.com.
· Multiple Managers
If more than one copy of Manager is running it is possible for the IP Office to request BIN files from a different
Manager from the one that started the upgrade process. Ensure that only one copy of Manager is running when
upgrading an IP Office system.
Procedure: Upgrade Procedure
and receive the configuration from the IP Office. If not already done this action
1. Using IP Office Manager, click
creates a BOOTP entry in Manager for the IP Office system. This action also confirms communication between the
Manager PC and the IP Office.
2. Select File | Save Configuration As... and save a copy of the configuration file onto the PC. This action should be
completed before upgrading any IP Office system.
3. Select File | Advanced | Upgrade.
4. The UpgradeWiz is started and scans for IP Office unit using the Unit/Broadcast address. Adjust this address and
click Refresh if the expected modules are not shown.
5. For each the unit found, the UpgradeWiz displays the module type, its current version of software installed in the
unit and the software version of the .bin file that Manager has available.
6. For those units and modules where manager detects that it has a higher version available, the tick box next to the
unit or module is automatically selected.
7. For those modules which you want to upgrade, tick the check box. For modules where a later version of software is
available the check box may have already been automatically ticked.
8. Select Upgrade.
9. The system password will be requested. Enter it and click OK.
10.The bin files required are transferred to the system and stored in temporary memory.
11.Once all the files have been transferred, the upgrade wizard will prompt whether it okay to proceed with the
upgrade process. Select Yes to continue.
12.Each module being upgraded will delete its existing core software, restart and load the new software file that was
transferred. This process may take several minutes for each unit. Do not cancel or close the upgrade wizard while
this process is running.
13.Following the upgrade check that the upgrade wizard now shows that the selected units and modules have
upgraded. It may be necessary to select Refresh to update the information in the upgrade wizard display.
IP Office Standard Version Installation
IP Office 7.0
Page 183
15-601042 Issue 23e (16 March 2011)
8.9 Receiving the Configuration
The process here applies to systems running IP Office 3.2 and higher.
Objective - Receive a configuration from an IP Office running IP Office 3.2 or higher
software.
Information Required
· o Service User Name and Password
The defaults for full configuration access are Administrator and Administrator.
However these should have been changed as part of the installation process, see
Configuring Security Settings.
Procedure: Receiving the Configuration
1. Select Start | Programs | IP Office | Manager.
2. Click
in the main toolbar or select File | Open Configuration from the menu bar.
3. The Select IP Office window appears. After a few seconds it should list the control unit that is being setup. The
default name used is the control units MAC address.
· If the system required was not found, the address used for the search can be changed. Enter or select the
required address in the Unit/Broadcast Address field and then click Refresh to perform a new search.
4. Click the check the box next to the system and then click OK.
5. The name and password request is displayed. The name and password must match one of those setup through the
security settings. The default name and password for full configuration settings access is Administrator and
Administrator.
6. Successful receiving of the configuration is shown by the full configuration tree being shown in the left-hand panel.
With no configuration loaded the navigation pane shows just BOOTP and Operator entries.
IP Office Default Settings
The following are the basic default configuration settings for an IP Office system.
System
Name
MAC address of the control unit.
System Password
password
License Server IP Address
255.255.255.255
LAN1
LAN1
LAN2/WAN
IP address
192.168.42.1.
192.168.43.1
IP Mask
255.255.255.0
255.255.255.0
DHCP Mode
Server
Server
No of DHCP IP Addresses
200.
200.
· Extensions and Users
A user is automatically created for each physical extension port detected in the system. Users are assigned extension
numbers starting from 201. User names take the form Extn201, Extn202, ....
· Hunt Group
A single hunt group 200 called Main is created and the first 10 users are placed into that hunt group as members.
· Incoming Call Routes
Two default incoming call routes are created. Voice calls are routed to the hunt group Main. Data calls are routed to the
RAS user DialIn.
IP Office Standard Version Installation
IP Office 7.0
Page 184
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Receiving the Configuration
8.10 Adding Licences
32-Character license keys strings are used to activate various IP Office features. These keys are
uniquely based on the feature being activated and the serial number of the Feature Key dongle
installed with the IP Office system.
Licenses can be added individually to the IP Office's configuration. However the licence key file provided by Avaya from
their license ordering web site generates a License.csv file containing all the ordered licenses. That file can be imported
into the configuration.
Parts and Equipment Required
· o License Keys Documentation
Ensure that the Feature Key dongle serial number used to generate the license keys matches that of the Feature
Key dongle installed and that all the licenses required have been included.
Importing a License.csv File
1. Copy the License.csv file to the Manager PC.
2. Start Manager and receive the IP Office system's configuration.
3. Select File | Import/Export | Import... .
4. Click the button next to Look In and browse to and select the folder containing the license file.
5. The file should be listed as Available along with an indication of the number of licenses it contains. Select the check
box next to the file name and then clock OK.
6. Click on
to send the configuration back to the IP Office.
7. Use Manager to receive the configuration again and check that the status of the licenses. They should now be Valid.
Manually Adding Licenses
Use this process to individually copy and paste license keys into the configuration. Cutting and pasting removes any errors
that may be caused by the incorrect typing of any license key.
1. Start Manager and receive the IP Office system's configuration.
2. Select
License.
3. To add a license, click
and select License. Enter the new license and click OK.
4. The Status of the new license should show Unknown and name the license as expected. If its Status is Unknown
and name Invalid, the most likely cause is incorrect entry of the license key characters.
5. Repeat the process for any other licences
6. Click on
to send the configuration back to the IP Office.
7. Use Manager to receive the configuration again and check that the status of the licenses. They should now be Valid
.
IP Office Standard Version Installation
IP Office 7.0
Page 185
15-601042 Issue 23e (16 March 2011)
8.11 Adding External Expansion Modules
External expansion modules connect to the IP Office control unit using an
expansion interconnect cable.
Objective - Connect the external expansion modules and then restart the
control unit so that the new modules are recognized.
Each module is supplied with an expansion connect cable and a power supply unit
33 .
An appropriate locale specific power cord 34 for the power supply unit, and cables
36 for the ports on the front of the module must be ordered separately.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
Installation Requirements
· o Installation space either on or under the existing IP Office control unit.
· o Switched power outlet socket.
· o Available EXPANSION port on the control unit.
· o Grounding Requirements
· o Functional Grounding
Connection of a functional earth
38
is:
· o Recommend for all modules.
· o Connection of a functional ground is mandatory for Analog Trunk module.
· o Protective Grounding
Connections of a protective ground via surge protection equipment
39
is:
· o Mandatory for Analog trunk modules in the Republic of South Africa.
· o Mandatory for Digital Station and Phone modules connected to out of building extensions.
· o Mandatory for Digital Station V2 and Phone V2 modules.
Tools Required
· o Manager PC.
· o Tools for rack mounting
188
(optional).
IP Office Standard Version Installation
IP Office 7.0
Page 186
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Adding External Expansion Modules
Parts and Equipment Required
· o External Expansion Module.
Each module is supplied with a suitable external power supply unit and a 1m blue interconnect cable. 2m Yellow
interconnect cables are supplied with the IP500 4-Port Expansion card and should only be used with that card.
· o Power cord for the power supply unit
· o Rack mounting kit
40
34
.
(optional).
· o Cable labeling tags.
Procedure
1. Switch off power to the IP Office control unit.
2. Attach the external expansion module's power supply.
3. Connect the expansion interconnect cable from the module's EXPANSION port to the first free EXPANSION port on
the control unit.
4. Make careful note of the port used and include this detail on the cable label and any other system records.
5. Switch on power to the module. Wait for the center LED on the front of the module to change from red to green.
6. Switch on power to the control unit.
7. Once the control unit has rebooted, using Manager receive the system configuration.
8. Click on
Unit in the left-hand panel.
9. Check that the list of units shown in the right-hand panel is correct.
10.The external expansion modules should be upgraded to the same level of software as the control unit. Do this by
repeating the IP Office upgrade process (see K. Upgrading the Core Software 183 ).
IP Office Standard Version Installation
IP Office 7.0
Page 187
15-601042 Issue 23e (16 March 2011)
8.12 Rack Mounting
The IP500 control unit and IP500 external expansion units can be
rack mounted if required into 19-inch rack systems. This requires
an IP500 Rack Mounting Kit (SAP 700429202) for each unit.
The kit includes:
· A rack mounting bracket and screws for attachment of the
bracket to the unit
· Nuts and bolts for rack attachment.
· Brackets and cable ties for cable tidying.
As indicated in the diagram following, the rack mounting bracket
can be used in several positions on the unit. IP400 external
expansion units used in an IP500 system can also be rack mounted
but use a separate IP400 Rack Mounting Kit.
Environmental Requirements
In addition to the existing environmental requirements
considered when rack mounting a unit:
54
for an IP Office system, the following additional factors must be
1. Rack Positioning - Ensure compliance with the rack manufacturers safety instructions. For example check that the
rack legs have been lowered and fixing brackets have been used to stop toppling.
2. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given
to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
· o Operating Temperature: 0°C (32°F) to 40°C (104°F).
· o Operating Humidity: 10% to 95% non-condensing.
3. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for
safe operation of the equipment is not compromised. Proper ventilation must be maintained. The side ventilation
slots on the IP500 control unit should not be covered or blocked.
4. Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
5. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
6. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
7.
Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 188
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Rack Mounting
·
Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 189
15-601042 Issue 23e (16 March 2011)
8.13 Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Standard Version Installation
IP Office 7.0
Page 190
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Wall Mounting
8.13.1 Wall Mounting Kit V2
These notes relate to the IP500 Wall Mounting Kit V2 (SAP 700500923). This kit can be used to wall mountIP500v2 control
units and IP500 external expansion modules.
The kit includes all components necessary for wall mounting onto a plywood surface. The use of the cable covers is
optional.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
· The installation must be done by a service person only.
· For control units, the mesh flame screen must be installed in the bottom edge of the control unit before mounting.
· Ensure that the system has been shutdown and power has been removed from all the units. Shutdown the system
using a shutdown command and then remove power. Do not simply remove the power.
· If mounting a control unit, you must wait at least 15 minutes after removing the power cord before fitting the flame
screen.
· A suitable mounting surface of at least 19mm (0.75 inch) plywood is required.
IP Office Standard Version Installation
IP Office 7.0
Page 191
15-601042 Issue 23e (16 March 2011)
Wall Mounting Process
Figure 1
1. Shutdown the System
Ensure that the system has been shutdown and power has been removed
from all the units.
· If mounting a control unit, you must wait at least 15 minutes after
removing the power cord before fitting the flame screen.
· Shutdown the system using a shutdown command and then remove
power. Do not simply remove the power.
Figure 2
2. Fit the Flame Screen: Mandatory - Control Units Only (See Figure 1)
·
! WARNING: The flame screen mesh must be fitted.
a. Remove the cards or blank slot covers from the left-hand and righthand slots.
b. Insert the flame screen into the bottom of the control unit, with the
two black plastic pegs at the front.
c. Press the two pegs through the air flow holes in the control unit
casing.
Figure 3
d. Check that the pegs have come through and have secured the flame
screen in place and that the screen is flush with the chassis.
3. Attach Brackets on One Side (See Figure 2)
On one side of the unit, attach one pair of the metal brackets.
· Only use the screws provided with the wall mounting kit for attaching
the metal brackets.
4. Attach the Cable Cover and Bracket (See Figure 3)
Use of the cable covers is optional. If not being used, simply attach the other
pair of brackets to the other side of the unit; otherwise:
Figure 4
a. Hook one of the cable covers into the leading hole of one of the metal
brackets.
b. Hook another bracket onto the other end of the cable cover and then
attach that bracket to the unit.
Figure 5
c. Repeat the process to attach the other cable cover to the unit.
5. Fit the Wall Bracket (See Figure 4)
Using 2 of the screws provided with the kit, attach the wall bracket to the
plywood surface.
Figure 6
6. Place the Unit onto the Wall Bracket (See Figure 5)
Lift the unit onto the wall bracket. The two metal brackets at the top of the
unit hook over the top of the wall bracket.
7. Attach the Unit to the Wall Panel (See Figure 6)
a. Using the remaining 4 screws provided with the kit, fix the cover
brackets to the plywood surface.
b. Reinsert the base cards and blank slot covers.
IP Office Standard Version Installation
IP Office 7.0
Page 192
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Wall Mounting
8.13.2 Wall Mounting Kit V1
These notes relate to the older design of wall mounting kit (SAP 70043015) used
for IP500 and IP500v2 control units. This kit cannot be used for external expansion
modules.
The kit includes two brackets, one top and one bottom, and screws for attachment
to the control unit. Additional 4 x 4.5mm fixtures and fittings are required suitable
for the wall type.
In addition to the existing environmental requirements 54 for an IP Office system,
the following additional requirements apply when wall mounting a unit:
· The wall surface must be vertical, flat and vibration free. Attachment to
temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the
brackets to the control unit.
· The brackets must be used as shown, with the deeper tray-like bracket used
at the bottom of the wall mounted control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 193
15-601042 Issue 23e (16 March 2011)
8.14 Grounding
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially
important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and
data networks.
All IP Office control units and external expansion modules must be connected to a functional ground. Where the unit is
connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective
earth.
In some cases, such as ground start trunks, in addition to being a protective measure this is a functional requirement for
the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for
example areas of high lightning risk.
·
WARNING
During installation do not assume that ground points are correctly connected to ground. Test ground points before
relying on them to ground connected equipment.
· Additional protective equipment
In addition to grounding, additional protective equipment will be required in the following situations.
· On any Digital Station or Phones external expansion module connected to an extension located in another
building. Refer to "Out of Building Telephone Installations 39 ".
· In the Republic of South Africa, on all Analog Trunk external expansion modules (ATM16) and on any control
units containing an analog trunk cards (ATM4/ATM4U).
Tools Required
· o M4 Cross-Head Screwdriver.
· o Tools suitable for crimping a cable spade.
Parts and Equipment Required
· o 14AWG Solid copper wire for ground connection.
· o Cable sleeve matching local regulator requirements. Typically green for a functional ground and green/yellow for
a protective ground.
The ground point on IP Office control units and expansion modules are marked with a
or
symbol. Ground
connections to these points should use a 14 AWG solid wire with either a green sleeve for a functional ground or green and
yellow sleeve for a protective ground.
IP500/IP500v2 Control Unit
On IP500 control units the ground point is located above the RS232 DTE port.
External Expansion Modules
On expansion modules, the ground point is a 4mm screw located towards the right on the rear of the module.
· On some older modules, the dedicated ground point screw is not present. In those cases, the top-center cover
fixing screw (3mm) can be used as an alternative ground connection point. A toothed washer should be added to
ensure good contact.
IP Office Standard Version Installation
IP Office 7.0
Page 194
15-601042 Issue 23e (16 March 2011)
IP500 Basic Installation: Grounding
IP Office Standard Version Installation
IP Office 7.0
Page 195
15-601042 Issue 23e (16 March 2011)
Chapter 9.
System Components
IP Office Standard Version Installation
IP Office 7.0
Page 197
15-601042 Issue 23e (16 March 2011)
9. System Components
This section covers the individual components that can comprise an IP Office installation.
· Control Units
199
· IP500 Base Cards
205
· IP500 Trunk Daughter Cards
218
· IP500 External Expansion Modules
· Feature Keys/SD Cards
· IP400 Trunks Cards
236
239
· IP400 Internal Cards
244
· IP400 External Expansion Modules
· Mounting Kits
· Phones
223
246
260
262
· Phone Add-Ons
337
· Ancilliary Systems
· Applications
351
· Physical Ports
· Licenses
349
370
386
IP Office Standard Version Installation
IP Office 7.0
Page 198
15-601042 Issue 23e (16 March 2011)
System Components:
9.1 IP500v2 Control Unit
The slots are numbered 1 to 4 from left to right. They can be used in any order. However if the capacity for a particular
type of card is exceeded, the card in the rightmost slot will be disabled. The unit must not be used with uncovered slots.
Feature
Capacity
Maximum
Extensions
Up to 384 extensions in IP Office Standard Version mode. Up to 100 extensions in IP Office Essential
Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Versionmodes.
Conference
Parties
128 as standard but maximum 64 in any individual conference. Silence suppression is applied to
conferences with more than 10 parties.
Trunks Cards
4. Any combination of IP500 trunk daughter cards and up to 2 IP400 trunk cards.
Voice
Compression
Channels
Up to 148 channels using up to IP500 VCM, IP400 VCM and IP500 Combination cards.
Voicemail
Channels
Maximum 40 usable for Voicemail Pro/TAPI WAV connection sessions subject to available licenses.
For Embedded Voicemail, up to 6 (2 by default, additional channels require licenses).
Locales
Supported in all IP Office locales.
Software Level
IP Office Standard Version Mode: 6.0 minimum. IP Office Essential Edition - PARTNER® Version
Mode: 6.0 minimum. IP Office Essential Edition - Norstar Version Mode: 6.1 minimum. IP Office
Essential Edition - Quick Version Mode: 7.0 minimum. Bin file = ip500v2.bin.
Power Supply
Internal power supply unit.
Mounting
Free-standing, rack mounted (requires IP500 Rack Mounting Kit) or wall mounted (requires IP500
Wall Mounting Kit).
Dimensions
Width: 445mm/17.5". Depth: 365mm/14.4". Height: 73mm/2.9"/2U. Clearance: 90mm minimum all
sides, 220m at front.
Memory
Maximum configuration file size: 2048KB.
Name
Description
IPO 500 V2 Base Unit
IP Office 500 V2 Base Unit
700476005
Avaya SD Memory Card
IPO System SD Card A-Law
700479702
IPO System SD Card Mu-Law
700479710
IPO System SD Card Partner
700479728
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IEC60320 C13 Earthed Power Cord
IP500 Rack Mounting Kit
IP Office Standard Version Installation
IP Office 7.0
Country
IP500 Rack Mounting Kit
SAP Code
700429202
Page 199
15-601042 Issue 23e (16 March 2011)
IP500 Wall Mounting Kit V2
IP500 Wall Mounting Kit
700500923
IP500 Wall Mounting Kit
IP500 Wall Mounting Kit
700430150
IP500 Blanking Plate Kit
IP500 Blanking Plate Kit
700429194
IP Office Standard Version Installation
IP Office 7.0
Page 200
15-601042 Issue 23e (16 March 2011)
System Components: IP500v2 Control Unit
Ports
Description
AUDIO
AUX
373
3.5mm Stereo jack socket. Used for external music on hold source input.
If pressed during a restart of the control unit, the control unit skip booting 155 from the /primary folder
on the System SD card. If pressed for more than 5 seconds when a system is running, the control unit
will shutdown 117 for 10 minutes.
155
CPU
Indicates the status of the control unit.
· Alternate red/green = Starting up.
· Green on = Okay.
EXPANSION
379
EXT O/P
INPUT
LAN
135
34
· Red on = No software.
· Flashing Red = Error/Shutdown.
RJ45 socket. Used for direct connection to external expansion modules using the Expansion Interconnect
cable supplied with the expansion module.
3.5mm Stereo jack socket. Used for switching external relay systems such as door entry controls. The
port contains two independent switches controlled by the IP Office.
AC power input port.
RJ45 socket. The port is a full-duplex 10/100Mbps auto-sensing, MDI crossover port. With the WAN port
forms a managed layer 3 Ethernet switch.
380
Optional SD
Used for the Optional SD card. The LED is used in the same way as for the System SD (see below).
152
RESET
143
This switch is used to restart the IP Office, optionally erasing the configuration and or the core software in
the process. See Reset Button 143 .
RS232
144
9-Way D-Type socket. Used for system maintenance.
System SD
152
WAN
Used for the System SD card,. The LED is used as follows.
·
·
·
·
380
Off = Card shutdown 167 .
Green on = Card present.
Green flashing = Card in use.
Orange steady = Reset imminent.
· Red flashing = Card initializing or shutting down.
· Red fast flashing = card full
· Red steady = Card failure/wrong type.
RJ45 socket. The port is a full-duplex 10/100Mbps auto-sensing, MDI crossover port. With the WAN port
forms a managed layer 3 Ethernet switch. This port is not supported on systems running in IP Office
Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version or IP Office Essential
Edition - Quick Version modes.
Used for connection of a functional or protective ground 90 . Use of a ground for all systems is
recommended and for some locales may be a regulatory requirement.
IP Office Standard Version Installation
IP Office 7.0
Page 201
15-601042 Issue 23e (16 March 2011)
9.2 IP500 Control Unit
The slots are numbered 1 to 4 from left to right. They can be used in any order. However if the capacity for a particular
type of card is exceeded, the card in the rightmost slot will be disabled. The unit must not be used with uncovered slots.
Feature
Capacity
Maximum
Extensions
Up to 384 extensions.
Conference
Parties
128 as standard but maximum 64 in any individual conference. Silence suppression is applied to
conferences with more than 10 parties.
Trunks Cards
4. Any combination of IP500 trunk daughter cards and up to 2 IP400 trunk cards.
Voice
Compression
Channels
Up to 148 channels using up to IP500 VCM, IP400 VCM and IP500 Combination cards.
Voicemail
Channels
Maximum 40 usable for Voicemail Pro/TAPI WAV connection sessions subject to available licenses
(maximum 30 pre-IP Office 5.0). For Embedded Voicemail, up to 6 (2 by default, additional channels
require licenses).
Locales
Supported in all IP Office locales.
Software Level
· IP Office core software level 4.0 minimum.
· Bin file = ip500.bin.
Power Supply
Internal power supply unit.
Mounting
Free-standing, rack mounted (requires IP500 Rack Mounting Kit) or wall mounted (requires IP500
Wall Mounting Kit).
Dimensions
Width: 445mm/17.5". Depth: 365mm/14.4". Height: 73mm/2.9"/2U. Clearance: 90mm minimum all
sides, 220m at front.
Memory
Maximum configuration file size: 1024KB.
Name
Description
IPO 500 Base Unit
IP Office 500 Base Unit
700417207
Smart Card Feature Key
Smart Card Feature Key (MU-Law)
700417470
Smart Card feature Key (A-Law)
700417488
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
IEC60320 C13 Earthed Power Cord
Country
SAP Code
America
700289770
IP500 Rack Mounting Kit
IP500 Rack Mounting Kit
700429202
IP500 Wall Mounting Kit V2
IP500 Rack Mounting Kit
700500923
IP500 Wall Mounting Kit
IP500 Wall Mounting Kit
700430150
IP Office Standard Version Installation
IP Office 7.0
Page 202
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Control Unit
IP500 Blanking Plate Kit
IP Office Standard Version Installation
IP Office 7.0
IP500 Blanking Plate Kit
700429194
Page 203
15-601042 Issue 23e (16 March 2011)
Ports
Description
AUDIO
373
3.5mm Stereo jack socket. Used for external music on hold source input.
CPU
· Alternate red/green = Starting up.
· Green on = Okay.
C/F
·
·
·
·
C/F TII
Used to house the optional embedded voicemail card.
EXPANSION
RJ45 socket. Used for direct connection to external expansion modules using the Expansion Interconnect
cable supplied with the expansion module.
379
EXT O/P
135
Off = Card shutdown 167 .
Green on = Card present.
Green flashing = Card in use.
Orange steady = Reset imminent.
· Red on = No software.
· Flashing Red = Error/Shutdown.
· Red flashing = Card initializing or shutting down.
· Red fast flashing = card full
· Red steady = Card failure/wrong type.
3.5mm Stereo jack socket. Used for switching external relay systems such as door entry controls. The
port contains two independent switches controlled by the IP Office.
INPUT
AC power input port.
LAN
RJ45 socket. With the WAN port forms a managed layer 3 Ethernet switch. The ports are full-duplex
10/100Mbps auto-sensing, MDI crossover ports.
380
RESET
143
This switch is used to restart the IP Office, optionally erasing the configuration and or the core software in
the process. See Reset Button 143 .
RS232
144
9-Way D-Type socket. Used for system maintenance.
USB
WAN
Not used.
380
RJ45 socket. With the LAN port forms a managed layer 3 Ethernet switch. The ports are full-duplex
10/100Mbps auto-sensing, MDI crossover ports.
Used for connection of a functional or protective ground 194 . Use of a ground for all systems is
recommended and for some locales may be a regulatory requirement.
IP Office Standard Version Installation
IP Office 7.0
Page 204
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Control Unit
9.3 IP500 Base Cards
The IP500 and IP500v2 control units have 4 slots for the insertion of IP500
base cards. The slots are numbered 1 to 4 from left to right. Normally they
can be used in any order, however if the capacity for a particular type of
card is exceeded, the card in the rightmost slot will be disabled.
Each base card includes an integral front panel with ports for cable
connections. Typically the first 8 ports on the left are for connection of
extension devices. The 4 ports on the left are used for connection of trunks
if a trunk daughter card 22 is added to the base card.
IP500 Digital Station Base Card
212
This card provides 8 DS (digital station) ports for the connection of
Avaya digital phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 3 per control unit.
· 4400 Series phones (4406D, 4412D and 4424D) are not
supported on this card. They are supported on external
expansion module DS ports.
· Connections for 4100, 7400, M-Series and T-Series phones use
the IP500 TCM8 Digital Station card.
IP500 Analog Phone Base Card
209
The card is available in two variants, supporting either 2 or 8 analog
phone ports.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 4 per control unit.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP500 TCM8 Digital Station Card
215
This card provides 8 TCM (digital station) ports for the connection of
Avaya 4100, 7400, M-Series and T-Series phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 4 per control unit per IP500v2 control unit. Not
supported by IP500 control units.
IP500 VCM Base Card
216
This card is available in variants supporting either 32 or 64 voice
compression channels for use with VoIP calls.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
22
which
· Maximum: 2 per control unit.
IP Office Standard Version Installation
IP Office 7.0
Page 205
15-601042 Issue 23e (16 March 2011)
IP500 Legacy Card Carrier Base Card
214
This card allows various IP400 trunk cards 24 and IP400 VCM cards 25
to be used. The front of the card includes panels that can be removed
to match the trunk card fitted.
· This card does not accept any IP500 trunk daughter card.
· Maximum: 2 per control unit.
· IP400 Cards Supported: The following cards are supported.
PRI T1
Dual PRI T1
PRI 30 E1 (1.4)
Dual PRI E1
IP500 4-Port Expansion Base Card
PRI 30 E1R2 RJ45
Dual PRI E1R2 RJ45
BRI-8 (UNI)
ANLG 4 Uni (US only)
VCM
VCM
VCM
VCM
VCM
4
8
16
24
30
208
This card adds an additional 4 expansion ports for external expansion modules. The
card is supplied with four 2m yellow interconnect cables.
· This card does not accept any IP500 trunk daughter card.
· Maximum: 1 per control unit (Right-hand slot 4 only).
· Supported Expansion Modules: The following external expansion modules are
supported:
·
·
·
·
IP500 BRI Combination Card
IP500
IP500
IP500
IP500
Analogue Trunk Module
BRI So Module
Digital Station Modules
Digital Station Modules A
· IP500 Phone Module
· IP400 Digital Station V2 Modules
· IP400 Phone V2 Modules
211
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 2 BRI trunk ports (9-10, 4 channels). The card also includes
10 voice compression channels.
· This card has a pre-installed IP500 BRI trunk daughter card
22
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type. Not supported by IP500 control units.
· IP Office Essential Edition - Norstar Version and IP Office
Essential Edition - Quick Version mode systems are limited to a
maximum of 12 BRI channels using BRI Combination and or BRI
trunk daughter cards.
IP500 ATM Combination Card
210
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 4 analog trunk ports (9-12). The card also includes 10 voice
compression channels.
· This card has a pre-installed IP500 analog trunk daughter card
22
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type. Not supported by IP500 control units.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP Office Standard Version Installation
IP Office 7.0
Page 206
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Base Cards
IP500 ETR6 Base Card
213
This card is only supported in an IP500v2 control unit running in IP
Office Essential Edition - PARTNER® Version or IP Office Essential
Edition - Quick Version mode. It is not supported in IP Office Essential
Edition - Norstar Version or IP Office Standard Version modes.
It provides 6 ETR ports for connection of ETR phones. 2 Analog
extension ports are also provided for emergency use only with an
analog trunk card.
· The card can be fitted with an IP500 trunk daughter card which uses
the base card ports for trunk connection.
· Maximum: 3 per IP500v2 control unit. Not supported by IP500
control units.
· The analog phone ports do not include a ringing capacitor. Where this
is a requirement, connection should be via a Master socket containing
ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone ports 7 and 8 are connected to analog trunk port 12.
However during normal operation analog phone ports 7 and 8 are not
useable.
IP Office Standard Version Installation
IP Office 7.0
Page 207
15-601042 Issue 23e (16 March 2011)
9.3.1 4-Port Expansion Card
This card is used to add 4 additional expansion ports to the IP500 and IP500v2 control unit. This card is only supported in
slot 4.
· Supports
Provides 4 additional expansion ports
modules.
379
for connection of external expansion
· Supported Expansion Modules: The following external expansion modules are
supported:
IP500
IP500
IP500
IP500
·
·
·
·
Analogue Trunk Module
BRI So Module
Digital Station Modules
Digital Station Modules A
· IP500 Phone Module
· IP400 Digital Station V2 Modules
· IP400 Phone V2 Modules
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 1 - Right hand slot 4 only.
· IP500 Trunk Card Support:
.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
LEDs 1 to 8 are used for the expansion ports on the rear of the control unit.
LEDs 9 to 12 are used for the card's own expansion ports.
Green
On
Expansion module present.
Red
Flashing
Initializing.
Red
On
Error.
Orange
Regular Flash
Base card okay.
Name
Description
SAP Code
IPO IP500 EXP CARD 4 PORT
Includes 4 yellow 2 metre interconnect
cables.
700472889
IPO EXP CABLE RJ45/RJ45 2M YELLOW Only for use with the 4-Port Expansion
card.
700472871
IP Office Standard Version Installation
IP Office 7.0
Page 208
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Base Cards
9.3.2 Analog Phone
This card is used to add analog phone ports to an IP500 and IP500v2 control unit. It is available in two variants, providing
either 2 or 8 analog extension ports.
· Supports
Provides either 8 or 2 analog
variant.
373
phone ports depending on card
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 4.
· IP500 Trunk Card Support:
Port Type
Ports
Features
Analog
Extension
1 to 8
·
·
·
·
·
1.
Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
REN 2 (1 for external bell device).
Off-Hook current: 25mA
Ring Voltage: 40V.
Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.
· If fitted with an analog trunk card, for the Phone 8, during power failure extension port
8 is connected to the analog trunk port 12.
Port LEDs
· No status LEDs are used for analog phone extensions.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
Port LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO 500 Extn Card Phone 2
IP Office 500 Extension Card Phone 2
700431778
IPO 500 Extn Card Phone 8
IP Office 500 Extension Card Phone 8
700417231
IP Office Standard Version Installation
IP Office 7.0
Page 209
15-601042 Issue 23e (16 March 2011)
9.3.3 ATM Combination Card
This card is used to add a combination of ports to an IP500v2 control unit. Not supported by IP500 control units.
· Supports
· 6 Digital Station ports.
· 2 Analog Extension ports.
· 4 Analog Trunk ports.
· 10 voice compression channels.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 2 combination cards of any type per
IP500v2 control unit.
· IP500 Trunk Card Support:
1. The trunk daughter card is preinstalled and cannot be replaced with another card type.
Port Type
Ports
Features
Digit Station
1 to 6
Provides DS
376
ports for digital stations
43
(except 4100, 4400, 7400, M and T-Series).
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Analog
Extension
7 to 8
·
·
·
·
·
Analog Trunk
9 to 12
·
·
·
·
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
REN 2 (1 for external bell device).
Off-Hook current: 25mA
Ring Voltage: 40V.
Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.
· During power failure extension port 8 is connected to the analog trunk port 12.
· No status LEDs are used for analog phone extensions.
DTMF, ICLID, Busy tone detection.
Over-voltage and lightning protection.
DTMF and LD dialing.
Adjustable echo cancellation (default 16ms). Selectable to Off, 8, 16, 32, 64 and 128
milliseconds.
LEDs
· Green on = Card fitted.
· Green flashing = Trunk in use.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Name
Description
SAP Code
IPO IP500v2 COMBINATION
CARD ATM
IPO IP500v2 COMBINATION CARD ATM
700476013
IP Office Standard Version Installation
IP Office 7.0
Page 210
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Base Cards
9.3.4 BRI Combination Card
This card is used to add a combination of ports to an IP500v2 control unit. Not supported by IP500 control units.
· Supports
· 6 Digital Station ports.
· 2 Analog Extension ports.
· 2 BRI Trunk ports (4 BRI channels).
· 10 voice compression channels.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 2 combination cards of any type.
· IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version mode systems are limited to a maximum of
12 BRI channels using BRI Combination and or BRI trunk daughter
cards.
· IP500 Trunk Card Support:
1. The trunk daughter card is preinstalled and cannot be replaced with another card type.
Port Type
Ports
Features
Digit Station
1 to 6
Provides DS
376
ports for digital stations
43
(except 4100, 4400, 7400, M and T-Series).
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog
Extension
7 to 8
·
·
·
·
·
BRI Trunk
9 to 10
· Each trunk port supports 2B+D channels.
· ETSI or AusTS013 basic rate protocol set through the IP Office configuration.
Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
REN 2 (1 for external bell device).
Off-Hook current: 25mA
Ring Voltage: 40V.
Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.
· No status LEDs are used for analog phone extensions.
LEDs
·
·
·
·
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
Not Used
11 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
–
Name
Description
SAP Code
IPO IP500v2 COMBINATION
CARD BRI
IPO IP500v2 COMBINATION CARD BRI
700476021
IP Office Standard Version Installation
IP Office 7.0
Page 211
15-601042 Issue 23e (16 March 2011)
9.3.5 Digital Station
This card is used to add digital station (DS) extension ports to an IP500 and IP500v2 control unit. It provides 8 RJ45 DS
extension ports for use with Avaya digital phones. A further 4 RJ45 ports are provided for trunk connections when an
IP500 trunk card is fitted to this card.
· Supports
Provides 8 DS 376 ports for digital stations
7400, M and T-Series).
43
(except 4100, 4400,
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 3 per control unit.
· IP500 Trunk Card Support:
Port Type
Ports
Features
Digit Station
1 to 8
Provides DS
376
ports for digital stations
43
1.
(except 4100, 4400, 7400, M and T-Series).
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
Port LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO 500 Extn Card Dgtl Sta 8
IP Office 500 Extension Card Digital Station 8
700417330
IP Office Standard Version Installation
IP Office 7.0
Page 212
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Base Cards
9.3.6 ETR6 Card
This card is used to add 6 ETR phone extension ports to an IP500v2 control unit. This card is only supported by IP500v2
systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version or IP
Office Essential Edition - Quick Version mode.
It also includes 2 analog extension ports which are for emergency use only when the card is fitted with an analog trunk
daughter card. A further 4 RJ45 ports (9 to 12) are provided for trunk connections when an IP500 trunk daughter card is
fitted to this card.
· Supports
ETR and analog phones. Each ETR phone can be used for an ETR or
analog phone. Support for ETR 34D phone is limited to a maximum of
2 per ETR6 card and 4 in total.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 3.
· IP500 Trunk Card Support:
1.
The IP500 BRI trunk daughter card is not supported.
Port Type
Ports
Features
ETR
Extensions
1 to 6
·
·
·
·
REN 1.
DTMF dialing only.
Message waiting indication 51V stepped.
ICLID mode Bellcore 202.
LEDs
· No status LED are used for ETR ports.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
EF
7 to 8
· If fitted with an IP500 Trunk Daughter card, during power failure both these ports are
connected to analog trunk port 12.
· Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
· REN 2 (1 for external bell device).
· Off-Hook current: 25mA
· Ring Voltage: 40V.
· Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master socket
with ringing capacitors.
· No status LEDs are used for analog phone extensions.
Optional
Trunk Ports
9 to 12
Depends on the type of trunk daughter card fitted. The ETR6 can be fitted with either a Analog
Trunk 220 card or PRI Trunk 222 card.
LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog
Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm
indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback
mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO IP500v2 EXTN CARD ETR6
IPO IP500v2 EXTN CARD ETR6
700476039
IP Office Standard Version Installation
IP Office 7.0
Page 213
15-601042 Issue 23e (16 March 2011)
9.3.7 Legacy Card Carrier
The IP500 Legacy Card Carrier base card can be used to fit IP Office IP400 cards into the IP500 or IP500v2 control unit.
This can include IP400 trunk and IP400 VCM cards. Up to 2 Legacy Card Carrier cards are supported in a control unit.
· Supports
The following IP400 cards are supported. Cards not listed are not
supported.
PRI T1
Dual PRI T1
PRI 30 E1 (1.4)
Dual PRI E1
PRI 30 E1R2 RJ45
Dual PRI E1R2 RJ45
BRI-8 (UNI)
ANLG 4 Uni (US only)
VCM
VCM
VCM
VCM
VCM
4
8
16
24
30
· IP400 PRI trunk cards fitted to IP500/IP500v2 systems do not
require trunk licenses.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 2.
· IP500 Trunk Card Support:
.
Name
Description
SAP Code
IPO 500 Carrier Card
IP Office 500 Carrier Card
700417215
Panels on the front of the carrier card can be snapped off to match the port
connects when fitting an IP500 trunk card.
IP Office Standard Version Installation
IP Office 7.0
Page 214
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Base Cards
9.3.8 TCM8 Digital Station
This card is used to add TCM RJ45 385 extension ports to an IP500v2 control unit. It provides 8 RJ45 extension ports for
supported M-Series and T-Series digital stations. It can also be used for 4100 and 7400 Series phone support by
connection to a Digital Mobility Solution 349 system.
A further 4 RJ45 ports are provided for trunk connections when an IP500 trunk card is fitted to this card.
· Supports
Provides 8 TCM 385 ports for supported 4100, 4400, 7400, M and TSeries digital stations.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 4.
· IP500 Trunk Card Support:
1.
Port Type
Ports
Features
TCM
1 to 8
Cable lengths up to 305 m (1000 ft) using 0.5mm (24AWG) wires do not require a power
booster. Lengths up to 790 m (2600 ft) are supported if an auxiliary power supply booster
is used.
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO 500 TCM 8
IP Office 500 TCM 8
700500758
IP Office Standard Version Installation
IP Office 7.0
Page 215
15-601042 Issue 23e (16 March 2011)
9.3.9 VCM
This type of card is used to add voice compression channels to an IP500 and IP500v2 control unit. Those channels are
used for VoIP calls including IP extensions and or IP trunks.
The IP500 VCM card is available in two variants; 32 channels and 64 channels. Both cards have 4 RJ45 ports for that are
used for connections when an IP500 daughter card 218 is fitted.
IP500 control units support up to 128 voice compression channels, using IP500 VCM cards and/or IP400 VCM cards 245 on
an IP500 carrier card 214 . The IP500v2 control unit supports up to 148 voice compression channels, using the same cards
plus voice compression ports on IP500 Combination Cards 210 .
· Supports
Codecs G.711, G729a and G.723 with 64ms echo cancellation. The
maximum number of simultaneous channels useable on an IP500
VCM base card is affected by the codec being used. The following
table assumes that all calls using the VCM use the same codec.
Codec
IP500 VCM32
IP500 VCM64
G.711
32
64
G.729a
30
60
G.723
22
44
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 2.
· IP500 Trunk Card Support:
Port Type
Ports
Features
Not present
1 to 8
Not present.
1.
LEDs
· LEDs 1 to 8 are unlabelled. They are used to indicate voice compression channel usage.
Each LED lit represents 12.5% of the available voice compression channel capacity in
use (total card capacity rather than licensed capacity).
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Name
IP Office Standard Version Installation
IP Office 7.0
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Description
SAP Code
Page 216
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Base Cards
IPO 500 MC VCM 32
IP Office 500 Media Card Voice Coding Module 32
700417389
IPO 500 MC VCM 64
IP Office 500 Media Card Voice Coding Module 64
700417397
IP Office Standard Version Installation
IP Office 7.0
Page 217
15-601042 Issue 23e (16 March 2011)
9.4 IP500 Trunk Daughter Cards
Most IP500 base cards 19 can be fitted with an IP500 trunk daughter
cards to support the connection of trunks to the base card.
Each daughter card is supplied with the stand off pillars required for
installation and a label to identify the daughter cards presence on the
front of the base card after installation.
· IP500 Combination cards are pre-fitted with a trunk daughter card
which cannot be removed or changed for another type of trunk
daughter card.
IP500 Analog Trunk Daughter Card
220
This card allows the base card to support 4 analog loop-start trunks.
· The analog phone ports do not include a ringing capacitor.
Where this is a requirement, connection should be via a Master
socket containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during
power failure phone port 8 is connected to analog trunk port
12.
· Maximum: 4 per control unit.
IP500 PRI-U Trunk Daughter Card
222
This card allows the base card to support up to 2 PRI trunk
connections. The card is available in single and dual port variants.
The card can be configured for E1 PRI, T1 robbed bit, T1 PRI or E1R2
PRI trunks.
· Maximum: 4 per control unit.
· The IP Office system supports 8 unlicensed B-channels on each
IP500 PRI-U port fitted. Additional B-channels, up to the capacity
of ports installed and PRI mode selected require IP500 Universal
PRI (Additional Channels) 388 licenses added to the
configuration. These additional channels consume the licenses
based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by
licensing.
IP500 BRI Trunk Daughter Card
221
This card allows the base card to support up to 4 BRI trunk
connections, each trunk providing 2B+D digital channels. The card is
available in 2 port (4 channels) and 4 port (8 channels) variants.
· Maximum: 4 per control unit.
· S-Bus Connection: The card can be switched from To trunk mode
to So mode. This mode requires additional terminating resistors
and an ISDN crossover cable connection, see BRI Port (So) 374 .
· IP Office Essential Edition - Norstar Version and IP Office
Essential Edition - Quick Version mode systems are limited to
a maximum of 12 BRI channels using BRI Combination and or
BRI trunk daughter cards.
IP Office Standard Version Installation
IP Office 7.0
Page 218
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Trunk Daughter Cards
IP Office Standard Version Installation
IP Office 7.0
Page 219
15-601042 Issue 23e (16 March 2011)
9.4.1 Analog Trunk Card
This card can be added to an IP500 base card to provide that card with support for 4 loop-start analog trunks.
This card can be fitted to any IP500 base card except the IP500 Legacy Carrier card and IP500 4-Port Expansion card.
· Ports/Channels
4 Loop-start analog trunk ports. Connections via the host IP500 base card.
· DTMF, ICLID, Busy tone detection.
· Over-voltage and lightning protection (may still require additional
protection equipment see Lightning Protection/Out-of-Building
Connections 39 .
· DTMF and LD dialing.
· Adjustable echo cancellation (default 16ms). Selectable to Off, 8, 16, 32,
64 and 128 milliseconds.
· Power Failure Port
Regardless of the IP500 card hosting it, during power failure pins 4 and 5
of port 12 are connected to pins 7 and 8. In addition, when fitted to an
IP500 Analog Phone 8 base card, during power failure extension port 8 is
connected to the analog trunk port 12.
· License: No license required.
· Maximum per Control Unit: 4.
· IP Office Software Level: 4.0+.
Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:
· Green on = Card fitted.
· Green flashing = Trunk in use.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card
okay.
· Red Fast Flash = System shutdown.
Name
Description
SAP Code
IPO 500 Trnk Anlg 4 Uni
IP Office 500 Trunk Card Analog 4 Universal
700417405
IP Office Standard Version Installation
IP Office 7.0
Page 220
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Trunk Daughter Cards
9.4.2 BRI Trunk Cards
This card can be added to an IP500 base card to provide that card with support for BRI-To
in 8 channel (4 physical trunks) or 4 channel (2 physical trunks) variants.
375
trunks. The card is available
This card can be fitted to any IP500 base card except the IP500 Legacy Carrier card and IP500 4-Port Expansion card.
· Ports/Channels
2 or 4 BRI trunk ports. Connections via ports 9 to 12 of the host IP500 base
card.
· Each trunk port supports 2B+D channels.
· ETSI or AusTS013 basic rate protocol set through the IP Office
configuration.
· License: No license required.
· Maximum per Control Unit: 4.
· IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version mode systems are limited to a maximum of 12
BRI channels using BRI Combination and or BRI trunk daughter cards.
· IP Office Software Level: 4.0+.
· S-Bus Connection: On IP Office 4.2+ systems, the card can be switched
from To 375 trunk mode to So 374 mode. This mode requires additional
terminating resistors and an ISDN crossover cable connection, see BRI Port
(So) 374 .
· This card is approved for use in the following countries:
Brazil.
New Zealand.
China.
Russia.
India.
South Africa.
Argentina.
United Arab Emirates (UAE).
Australia.
European Union (EU).
Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:
·
·
·
·
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card
okay.
· Red Fast Flash = System shutdown.
Name
Description
SAP Code
IPO 500 Trnk BRI 4 Uni
IP Office 500 Trunk Card Basic Rate 4 Universal
700417413
IPO 500 Trnk BRI 8 Uni
IP Office 500 Trunk Card Basic Rate 8 Universal
700417421
IP0 IP500 BRI S0 CONVTR
CBL
IP500 BRI So Converter Cable
700458649
IP Office Standard Version Installation
IP Office 7.0
Page 221
15-601042 Issue 23e (16 March 2011)
9.4.3 PRI Trunk Cards
This card can be added to an IP500 base card to provide that card with support for PRI trunks. The card is available in
single port or dual port variants.
This card can be fitted to any IP500 base card except the IP500 Legacy Carrier card and IP500 4-Port Expansion card.
· Ports/Channels
1 or 2 PRI trunk ports 383 . Each port supports the following PRI line types.
On dual port cards, both ports will be the same line type. The line type
selection can be changed using IP Office Manager. The options available
depend on the IP Office operation mode and locale.
· E1 PRI (30B+D channels per port).
· E1R2 PRI (30B channels per port).
· T1 robbed bit (24B channels per port) or T1 PRI (23B+D channels
per port).
· The required mode can be selected within IP Office Manager by rightclicking on the line icon and selecting Change Universal PRI Card
Line Type and then selecting the required line type.
· Physical trunk connection is via ports 9 and 10 of the host IP500 base
card.
· Port 11 and 12 can be used as test points for connection of test and
monitoring equipment for the adjacent port.
· Licenses
The IP Office system supports 8 unlicensed B-channels on each IP500 PRI-U
port fitted. Additional B-channels, up to the capacity of ports installed and
PRI mode selected require IP500 Universal PRI (Additional Channels)
licenses added to the configuration. These additional channels consume the
licenses based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by licensing.
· Maximum per Control Unit: 4 per control unit in IP Office Standard
Version mode. 1 single port card only in other modes.
· Software Level: 4.1+.
Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm
indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback
mode (set through IP Office System Monitor).
· LED 9 is also used for daughter card status.
·
·
·
·
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card
okay.
· Red Fast Flash = System
shutdown.
Name
Description
SAP Code
IPO 500 TRNK PRI 1 UNI
IP Office 500 Trunk Card Primary Rate 1 Universal
700417439
IPO 500 TRNK PRI 2 UNI
IP Office 500 Trunk Card Primary Rate 2 Universal
700417462
IP Office Standard Version Installation
IP Office 7.0
Page 222
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Trunk Daughter Cards
9.5 IP500 Expansion Modules
The following IP500 external expansion modules are supported by IP Office Release 7.0. Each module uses an external
power supply unit 33 supplied with the module. A locale specific power cord 34 for the PSU must be ordered separately.
If being rack mounted, these units use the IP500 rack mounting kit. They can be wall mounted using the new wall
mounting kit V2.
· Systems running in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version or
IP Office Essential Edition - Quick Version mode support up to 8 external expansion modules so long as the system
extensions limit is not exceeded.
· Systems running in IP Office Standard Version mode support 8 external expansion modules or 12 if the control unit
is fitted with an IP500 4-Port Expansion Base Card.
· IP500 Digital Station Module 229
Provides, depending on variant, an additional 16 or 30 DS
supported Avaya DS digital phones 43 .
376
ports for
· IP500 Digital Station A Module 231
Provides, depending on variant, an additional 16 or 30 TCM 385 ports for
supported Avaya TCM digital phones 43 . Supported by IP500v2 only.
· IP500 Phone Module 234
Provides, depending on variant, an additional 16 or 30 PHONE
analog phones.
382
ports for
· IP500 BRI So8 Module 227
Provides 8 ETSI BRI-So ports 374 for the connection of ISDN devices. This unit
is not intended to support BRI trunks.
IP Office Standard Version Installation
IP Office 7.0
Page 223
15-601042 Issue 23e (16 March 2011)
· IP500 Analog Trunk Module 225
Provides an additional 16 ANALOG 373 ports for connection of analog trunks.
Supports both loop-start and ground-start trunks.
· Use with ground start trunks requires that the trunk module and the IP Office
control unit are grounded.
· In IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition
- Norstar Version and IP Office Essential Edition - Quick Version modes, only
1 Analog Trunk module is supported.
IP Office Standard Version Installation
IP Office 7.0
Page 224
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Expansion Modules
9.5.1 Analog Trunk 16
The IP500 Analog Trunk module can be used to add 16 additional analog trunks to an IP Office system. The module
supports both loop-start and, with suitable grounding, ground-start trunks.
· In IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office
Essential Edition - Quick Version modes, only 1 Analog Trunk module is supported.
· IMPORTANT
In all IP Office installations, any module being used for analog trunk connections must be connected to a functional
earth 38 .
·
WARNING
Within areas of high lightning risk, any module using analog trunk connections must be connected to a protective
ground 38 and to surge protection equipment 39 (an Avaya 146G Surge Protector).
Feature
Details
Supported on
IP500 and IP500v2.
Locales
This module is currently only supported in North American locales.
Software Level
IP Office core software level 1.0 minimum. Bin file = naatm16.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a 2-pin, 40W external power supply unit. The PSU has an integral
power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C7 power cord
33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 2.9Kg/6.6lbs. Boxed: 4.2Kg/9.4lbs.
IP Office Standard Version Installation
IP Office 7.0
Page 225
15-601042 Issue 23e (16 March 2011)
IPO 500 Analog Trunk Module Connections
Ports
Description
ANALOG
DC I/P
DTE
373
376
144
EXPANSION
379
PF
381
RJ45 socket. Used for connection to analog trunks. Ports can be configured as either loop-start or
ground-start trunks through the IP Office configuration.
In the event of power failure, Analog ports 1 and 2 are directly connected to analog extension ports PF1
and PF2 respectively. If used the connected phones must be clearly labeled as power failure devices. This
is only supported for loop-start analog trunks.
DC power input port. Used for connection of the power lead from an Avaya 40W external power supply
unit supplied with the expansion module. A locale specific IEC60320 C7 power cord 33 for the external
PSU is required but is not supplied with the module.
25-Way D-Type socket. For Avaya use only.
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
RJ45 socket. Power failure analog extension ports. See Analog section above.
Ground point. Used for connection of a functional earth 38 if required. On older modules where this
screw is not present, the top-center cover screw should be used instead.
· IMPORTANT
In all IP Office installations, any module being used for analog trunk connections must be connected to
a functional earth 38 .
·
WARNING
Within areas of high lightning risk, any module using analog trunk connections must be connected to
a protective ground 38 and to surge protection equipment 39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IPO 500 Analog Trunk 16
America
America
700449473
IEC60320 C7 Power Cord
NEMA1-15
America
700213390
IP500 Wall Mounting Kit V2
All
700500923
IP500 Rack Mounting Kit
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 226
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Expansion Modules
9.5.2 BRI SO8
The So8 module can be used to add ETSI BRI S0-interface ports to the IP Office system. These ports can then be used for
the connection of ISDN devices.
Feature
Details
Supported on
IP500 and IP500v2. The control unit must be running in IP Office Standard Version mode. This
module is not supported in IP Office Essential Edition - PARTNER® Version, IP Office Essential
Edition - Norstar Version or IP Office Essential Edition - Quick Version modes.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 1.0 minimum. Bin file = nas0-16.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The unit is supplied with an earthed 3-Pin, 60W external power supply unit. The PSU has an integral
power cord for connection to the unit's DC I/P socket. A locale specific IEC60320 C13 power cord
33 for the external PSU is required but is not supplied with the unit.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 2.8Kg/6.3lbs. Boxed: 4.1Kg/9.2lbs.
IP Office Standard Version Installation
IP Office 7.0
Page 227
15-601042 Issue 23e (16 March 2011)
IPO 500 So8 Module Connections
Ports
Description
BRI
RJ45 socket. Used for connection of ISDN terminal devices.
Note: These ports appear a lines within the IP Office configuration. However they cannot be used for
connection to external BRI lines.
374
DC I/P
DTE
376
144
EXPANSION
379
DC power input port. Used for connection of the power lead from an Avaya 60W external power supply
unit supplied with the expansion module. A locale specific IEC60320 C13 power cord 33 for the external
PSU is required but is not supplied with the module.
25-Way D-Type socket. For Avaya use only.
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Function ground point. Used for connection of a protective or functional 38 ground if required. On older
modules where this screw is not present, the top-center cover screw should be used instead.
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system. Expansion modules include an external power supply unit (PSU) and an appropriate
interconnect cable. They do not include a locale specific power cord for the external PSU or any phone extension cables.
Item
Variant
IPO 500 BRI So8
IEC60320 C13 Power Cord
Country
SAP Code
All
700449515
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IP500 Wall Mounting Kit V2
All
700500923
IP500 Rack Mounting Kit
All
700429202
IP Office Standard Version Installation
IP Office 7.0
Page 228
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Expansion Modules
9.5.3 Digital Station
IP Office 500 Digital Station modules can be used to add additional DS ports to an IP Office system. The module is
available in 16 and 30 port variants, referred to as the IP500 Digital Station 16 and IP500 Digital Station 30 respectively.
Feature
Details
Supported on
IP500 and IP500v2.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 2.1(31) minimum. Bin file = nadcpV2.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply module. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".
Weight
Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30 V2)
IP Office Standard Version Installation
IP Office 7.0
Page 229
15-601042 Issue 23e (16 March 2011)
IPO 500 Digital Station Connections
Ports
DC I/P
DS
Description
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external
power supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord
for the external PSU is required but is not supplied with the module.
376
RJ45 socket. Digital Station port. Used for connection of IP Office supported DS phones 43 .
If connected to an out-of-building extension 39 , the connection must be made via additional IROB
barrier devices in addition to the buildings primary protection. The module must also be connected to
a protective ground.
376
DTE
9-Way D-Type socket. For Avaya use only.
144
EXPANSION
33
379
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 90 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IPO 500 Digital Station
16 Ports
All
700449499
30 Ports
IEC60320 C13 Power Cord
700426216
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IP500 Wall Mounting Kit V2
All
700500923
IP500 Rack Mounting Kit
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 230
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Expansion Modules
9.5.4 Digital Station A
IP Office 500 Digital Station A modules can be used to add additional TCM 384 ports to an IP Office system. They provides
extension ports for supported M-Series and T-Series digital stations. They can also be used for 4100 and 7400 Series
phone support by connection to a Digital Mobility Solution 349 system.
The module is available in 16 and 30 port variants, referred to as the IP500 Digital Station 16A and IP500 Digital Station
30A respectively. Connection is via 1 (16 port version) or 2 (30 port version) J21 connectors.
Feature
Details
Supported on
IP500v2 only.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 7.0 minimum. Bin file = nadcpaV1.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply module. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".
Weight
Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30A)
IP Office Standard Version Installation
IP Office 7.0
Page 231
15-601042 Issue 23e (16 March 2011)
IPO 500 Digital Station A Connections
LEDs 1 to 16 or 1 to 30 indicate when a phone is connected. They do not indicate phone activity. The center LED indicate
the module status (Green = Okay, Red = Error, Flashing = Loading firmware).
Ports
DC I/P
Description
TCM RJ21
DTE
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external
power supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord
for the external PSU is required but is not supplied with the module.
376
RJ21 port. Provides extension ports for supported M-Series and T-Series digital stations. They can also
be used for 4100 and 7400 Series phone support by connection to a Digital Mobility Solution 349
system.
384
9-Way D-Type socket. For Avaya use only.
144
EXPANSION
33
379
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 90 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP500 Digital Station A
16 Ports
All
700500699
30 Ports
IEC60320 C13 Power Cord
700500698
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IP500 Wall Mounting Kit V2
IP500 Rack Mounting Kit
700500923
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 232
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Expansion Modules
RJ21 Cable Pin Out
The following pin-out is used for the RJ21 ports.
1st RJ21 Connector
Port
1
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
10
11
12
13
14
15
16
Not Used
2nd RJ21 Connector
Pin
Wire
Port
26
White/Blue
1
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
Tip
40
Black/Slate
Ring
15
Tip
Ring
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
Wire
26
White/Blue
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
40
Black/Slate
Slate/Black
15
Slate/Black
41
Yellow/Blue
41
Yellow/Blue
16
Blue/Yellow
16
Blue/Yellow
42
Yellow/Orange
42
Yellow/Orange
17
Orange/Yellow
17
Orange/Yellow
43
Violet/Slate
43
Violet/Slate
08
Slate/Violet
08
Slate/Violet
IP Office Standard Version Installation
IP Office 7.0
10
Pin
11
12
13
14
Not Used
Page 233
15-601042 Issue 23e (16 March 2011)
9.5.5 Phone
IP500 Phone modules can be used to add additional PHONE ports to an IP Office system.
The module is available in 16 and 30 port variants, referred to as the IP500 Phone 16 and IP500 Phone 30 respectively.
Feature
Details
Supported on
IP500 and IP500v2.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 2.1(36) minimum. Bin file = dvpots.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply unit. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".
Weight
Unboxed: 3.1Kg/6.94lbs. Boxed: 4.4Kg/9.7lbs. (Based on Phone 30 V2)
IP Office Standard Version Installation
IP Office 7.0
Page 234
15-601042 Issue 23e (16 March 2011)
System Components: IP500 Expansion Modules
IPO 500 Phone Connections
Ports
DC I/P
DTE
Description
376
9-Way D-Type socket. For Avaya use only.
144
EXPANSION
379
PHONE
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external power
supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord 33 for the
external PSU is required but is not supplied with the module.
382
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
RJ45 socket. Used for connection of analog phones. Intended for two-wire analog phones. For
connection to 4-wire analog phones connection should be via a master socket with ringing capacitors.
If connected to an out-of-building extension 39 , the connection must be made via additional IP Office
Barrier Boxes 133 in addition to the buildings primary protection. The module must also be connected to
a protective ground.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 38 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IPO 500 Phone
16 Ports
All
700449507
30 Ports
All
700426224
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IEC60320 C13 Power Cord
IP500 Wall Mounting Kit V2
IP500 Rack Mounting Kit
700500923
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 235
15-601042 Issue 23e (16 March 2011)
9.6 Feature Keys
The serial number of the feature key fitted to the IP Office control unit is used as the basis for all licenses issued for that
IP Office system and is used to regularly re-validate the licenses. If the feature key is removed, over the next few hours
licensed features will stop operating.
9.6.1 IP500v2 System SD Cards
This type of feature key is used with IP500v2 control units and is a mandatory item. The control unit must be fitted with
one of these feature keys even if no licenses are being used.
The serial number for licenses issued for use with this type of feature key is printed on the card label and prefixed by FK.
This type of feature key is also a memory card used for other system functions and to provide embedded voicemail if
required.
· By default the card can be used for 2 ports of embedded voicemail. Additional ports up to a maximum of 6 can be
enabled by the addition of licenses 387 . The voicemail mailbox message and prompt capacity supports 2
simultaneous connections and 15 hours of storage. This can be expanded up to 6 channels by the addition of
licenses, each of which enables an additional two channels and an additional 5 hours of storage.
·
WARNING
These cards should only be formatted using IP Office Manager or IP Office System Status Application. The cards
should only be removed from a system after either a card shut down 167 or a system shut down 169 .
Feature Key Dongle
SAP Code
IPO IP500 V2 SYS SD CARD A-LAW
700500924
IPO IP500 V2 SYS SD CARD MU-LAW
700500925
IPO IP500 V2 SYS SD CARD PARTNER
700500926
IPO IP500 V2 SYS SD CARD NORSTAR
700500927
· IP Office U-Law
A system fitted with this type of card will default to U-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode Key System operation. Intended for North American locales.
· IP Office A-Law
A system fitted with this type of card will default to A-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode PBX System operation. Intended for locales outside North
America.
· IP Office Partner Version
A system fitted with this type of card will default to U-Law telephony and IP Office Essential Edition PARTNER® Version mode Key System operation. Supported only in North American locales.
· IP Office Norstar Version
A system fitted with this type of card will default to A-Law telephony and IP Office Essential Edition - Norstar
Version mode Key System operation. Supported only in Middle East and North African locales.
· Avaya Branch Gateway
This type of SD card intended to be used with <%GATEWAY%> systems. The Avaya Branch Gateway System
SD card can only be used for Avaya Branch Gateway operation and cannot be used to change modes to IP
Office. You also cannot use or change an IP Office SD card for use with an Avaya Branch Gateway system.
Avaya Branch Gateway systems are not covered by this documentation.
PCM Encoding
· A-Law or Mu-Law
PCM (Pulse Code Modulation) is a method for encoding voice as data. In telephony, two methods PCM encoding are
widely used, A-law and Mu-law (also called U-law). Typically Mu-law is used in North America and a few other
locations while A-law by the rest of the world. As well as setting the correct PCM encoding for the region, the A-Law
or Mu-Law setting of an IP Office system when it is first started affects a wide range of regional defaults relating to
line settings and other values.
· For IP400 IP Office systems, each control units was manufactured as either an A-Law variant or a Mu-Law
variant.
· For IP500 and IP500v2 systems, the encoding default is set by the type of Feature Key installed when the
system is first started.
IP Office Standard Version Installation
IP Office 7.0
Page 236
15-601042 Issue 23e (16 March 2011)
System Components: Feature Keys
IP Office Standard Version Installation
IP Office 7.0
Page 237
15-601042 Issue 23e (16 March 2011)
9.6.2 IP500 Smart Card
This type of feature key is used with IP500 control units and is a mandatory item. The control
unit must be fitted with one of these feature keys even if no licenses are being used.
The serial number for licenses issued for use with this type of feature key is printed on the card
and prefixed by SN.
Feature Key Dongle
SAP Code
Smart Card Feature Key (Mu-Law)
700417470
Smart Card Feature Key (A-Law)
700417488
· A-Law or Mu-Law
PCM (Pulse Code Modulation) is a method for encoding voice as data. In telephony, two
methods PCM encoding are widely used, A-law and Mu-law (also called U-law). Typically
Mu-law is used in North America and a few other locations while A-law by the rest of the
world. As well as setting the correct PCM encoding for the region, the A-Law or Mu-Law
setting of an IP Office system when it is first started affects a wide range of regional
defaults relating to line settings and other values.
· For IP400 IP Office systems, each control units was manufactured as either an A-Law
variant or a Mu-Law variant.
· For IP500 and IP500v2 systems, the encoding default is set by the type of Feature
Key installed when the system is first started.
IP Office Standard Version Installation
IP Office 7.0
Page 238
15-601042 Issue 23e (16 March 2011)
System Components: Feature Keys
9.7 IP400 Trunk Cards
IP400 trunk cards can be used in IP500 and IP500 v2 controls units by being fitted onto an IP500 Legacy Card Carrier
base card. Up to 2 cards can be added to the control unit in this way.
214
The following IP400 trunk card types are supported in this way by IP Office Release 7.0:
IP400 Trunk Cards
IP500
IP500v
2
Analog Trunk Card (ATM4) 241
Provides 4 RJ45 loop-start analog trunk ports. The card is available in several
locale specific variants. This card has been superseded by the ATM4U card
below.
Additional loop or ground start analog trunks can also be added using Analog
Trunk 248 external expansion modules.
Analog Trunk Card (ATM4U) 240
Provides 4 RJ45 loop-start analog trunk ports as per the ATM4 above but
available in a single worldwide variant. Also supports adjustable echo
cancellation on IP Office 3.1.
Additional loop or ground start analog trunks can also be added using Analog
Trunk 248 external expansion modules.
Quad BRI Trunk Card 241
Provides support for 4 RJ45 BRI (2B+D) trunk ports. These can be configured
to ETSI or AusTS013 operation. The ports include 100ohm termination.
Single PRI T1 Trunk Cards 242
Supports PRI (23B+D) trunks and T1 Robbed-Bit (24B) trunks through a single
RJ45 port. The mode of operation is selected in the IP Office configuration.
Single E1 PRI Trunk Cards 242
Supports PRI (30B+D) trunks through a single RJ45 port. The port can be
configured for PRI or QSIG operation.
Single E1R2 Trunk Cards 243
Supports PRI (30B+D) trunks using E1R2 signaling. Available in coaxial or
RJ45 connector variants. Coaxial variants are not supported on an IP500
carrier card.
Dual PRI Trunk Cards 242
As the single PRI cards above but supporting the connection of two PRI trunks.
On the IP406 V2, supported in Slot A only.
IP Office Standard Version Installation
IP Office 7.0
Page 239
15-601042 Issue 23e (16 March 2011)
9.7.1 Analog Trunk Card Uni (ATM4U)
This card supersedes the previous Analog Trunk cards and is referred to as the "ATM4U". It can be identified by a label on
the base of the card.
The card is supported on IP Office software 2.1(36) and higher. Unlike the previous ATM4 card, the same ATM4U card
variant can be used in all locales.
For systems running IP Office software 3.1 or higher, the echo cancellation used on each trunk can be switched off or on
(16ms).
The card provides 4 RJ45 sockets for analog trunk connections 373 . The card only supports loop-start trunks. For groundstart trunks an Analog Trunk expansion module 248 should be used.
· Power Failure Operation
There are no power failure extension connections provided for the analog trunk card. If this is a requirement, the
ATM16 expansion module should be used.
·
WARNING
In all IP Office installations, any module or control unit using analog trunk connections must be connected to a
functional earth 38 .
·
WARNING
Within the Republic of South Africa and in areas of high lightning risk, any module or control unit using analog trunk
connections must be connected to a protective ground 38 and to surge protection equipment 39 .
ATM4U Trunk Card
ATM4 Uni (Loop-Start)
Country
SAP Code
All
700359938
IP500
IP500v
2
· The card includes two plastic stand off pillars for installation and a replacement blanking plate for the rear of IP400
control units.
· For the IP500 and IP500v2 control units, an IP500 Carrier Card is required, up to a maximum of 2 IP500 Carrier
Cards.
IP Office Standard Version Installation
IP Office 7.0
Page 240
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Trunk Cards
9.7.2 Analog Trunk Cards (ATM4)
The Analog Trunk card is also referred to as the "ATM4". It provides 4 RJ45 sockets for analog trunk connections
card only supports loop-start trunks.
373 .
The
The card is available in a number of locale specific variants as detailed below.
· Power Failure Operation
There are no power failure extension connections provided for the analog trunk card.
·
WARNING
In all IP Office installations, any module or control unit using analog trunk connections must be connected to a
functional earth 38 .
·
WARNING
Within the Republic of South Africa and in areas of high lightning risk, any module or control unit using analog trunk
connections must be connected to a protective ground 38 and to surge protection equipment 39 .
ATM4 Trunk Cards
Country
SAP Code
IP500
IP500v
2
IP400 Analog 4
(Loop-Start)
North and South
America
700185192
–
–
IP400 Analog 4 EU
(Loop-Start)
Europe
700241672
–
–
IP400 Analog 4 NZ
(Loop-Start)
New Zealand
700241706
–
–
· These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of
IP400 control units.
9.7.3 BRI Trunk Cards
The BRI trunk card is also referred to as the "Quad BRI". It provides 4 RJ45 sockets for ETSI BRI trunk connections, with
each trunk supporting 2B+D channels.
Variant
Country
IP400 BRI
All
IP400 BRI 8 (UNI)
All except China
SAP Code
IP500
IP500v
2
700185168
700262017
· The trunk card ports include 100 ohm termination.
· These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of
IP400 control units.
· For the IP500 and IP500v2 control units, an IP500 Carrier Card is required, up to a maximum of 2 IP500 Carrier
Cards.
IP Office Standard Version Installation
IP Office 7.0
Page 241
15-601042 Issue 23e (16 March 2011)
9.7.4 T1 PRI Trunk Cards
These trunk cards support 23B+D primary rate (US PRI) trunks and 24B T1 robbed-bit trunks. The mode of operation is
selected within the IP Office configuration.
The T1 PRI card includes an integral CSU/DSU that can be activated through the IP Office Monitor application.
PRI Trunk Cards
Country
SAP Code
IP400 PRI 24 T1
North America
700185200
IP400 PRI 48 T1
North America
700185218
IP500
IP500v
2
· These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of
IP400 control units.
· For dual port cards the IP406 V2 only supports a single dual card in Slot A.
· For the IP500 and IP500v2 control units, an IP500 Carrier Card is required, up to a maximum of 2 IP500 Carrier
Cards.
9.7.5 E1 PRI Trunk Cards
These cards support primary rate trunks providing 30B+D channels.
E1 PRI trunk Cards
Country
SAP Code
IP400 PRI 30 E1
(1.4)
All except China and
CALA.
700272461
IP400 PRI 60 E1
All except China and
CALA.
700185184
IP500
IP500v
2
· These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of
IP400 control units.
· For dual port cards the IP406 V2 only supports a single dual card in Slot A.
· For the IP500 and IP500v2 control units, an IP500 Carrier Card is required, up to a maximum of 2 IP500 Carrier
Cards.
IP Office Standard Version Installation
IP Office 7.0
Page 242
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Trunk Cards
9.7.6 E1R2 PRI Trunk Cards
These cards support E1 trunks with R2 signalling. Each trunk provides up to 30B+D channels.
E1R2 PRI trunk cards are available with either RJ45 or coaxial cable connectors.
E1R2PRI trunk Cards
IP400 PRI 30 E1R2 RJ45
Country
SAP Code
CALA, Korea, China
700241631
IP400 PRI 60 E1R2 RJ45
IP400 PRI 30 E1R2 COAX
IP500
IP500v
2
700241656
–
–
700241664
–
–
700241649
CALA
IP400 PRI 60 E1R2 COAX
· These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of
IP400 control units.
· For E1R2 coaxial card, a ground-jumper cable and coaxial connector locking rings are included.
· For dual port cards the IP406 V2 only supports a single dual card in Slot A.
· For the IP500 and IP500v2 control units, an IP500 Carrier Card is required, up to a maximum of 2 IP500 Carrier Cards.
E1R2 coax trunk cards must be grounded correctly and require the IP Office control unit to be connected to a protective
ground 38 . Normally the ends of one connection is grounded. For example, if the exchange Tx1 is grounded, the IP Office
Rx1 should also be grounded. However this must be confirmed with the line provider to establish which ends they want
grounded.
1. Connect the ground strap spade end (B) supplied with the card to the spade connection on the card and the other end
(C) to the chassis with the long securing screw also supplied with the card.
2. Use the two jumpers supplied with the card, match the ground selection of the line provider. For example, if the line
provider has grounded their Tx1, place a jumper across the two Rx1 pins of jumper block J6.
IP Office Standard Version Installation
IP Office 7.0
Page 243
15-601042 Issue 23e (16 March 2011)
9.8 IP400 Internal Cards
9.8.1 Embedded Voicemail Memory Cards
This card is supported on IP500 control units. It is a specially formatted Compact Flash cards that provides embedded
voicemail operation and can also be configured for basic auto-attendant support. Use of these cards for voicemail does not
require a license.
·
These cards are not hot swappable. Removal of the cards while the IP Office control unit is powered may cause
lose or corruption of messages and prompts. IP Office Manager can be used to shutdown a memory card 120 before
its removal.
Variant
Country
Uses a specially formatted Avaya 512MB Compact Flash card.
This card provides up to 15 hours storage for uncompressed
prompts, greetings and messages. Operation of this card
does not require voice compression channels.
IP500
All
IP500v SAP Code
2
–
700343460
Supports up to 4 simultaneous connections, non expandable.
· From IP Office 3.0 onwards, the prompt files for the following languages are pre-installed on the Avaya memory cards.
· Danish
· Finnish
· Portuguese
· German
· French
· Portuguese-Brazilian
· English-UK
· French-Canadian
· Russian
· English-US
· Italian
· Swedish
· Spanish
· Korean
· Chinese - Mandarin
· Spanish-Mexico
· Dutch
· Spanish-Argentina
· Norwegian
· Chinese- Cantonese (IP Office 4.2
+)
· For full details of embedded voicemail setup and configuration, refer to the Embedded Voicemail Installation manual.
· The memory card can also be used for storage of files normally obtained via TFTP transfer. For example the music-onhold wav file and supported 4600 Series/5600 Series software files. This will however reduce storage space for prompt
and message files if embedded voicemail is being used. Non-Avaya memory cards can be used for this function.
· The memory card is specially formatted by Avaya for embedded voicemail operation. Reformatting the card will stop
embedded voicemail support and require the card to be replaced.
IP Office Standard Version Installation
IP Office 7.0
Page 244
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Internal Cards
9.8.2 Voice Compression Modules
IP400 VCMs are optional cards that can be installed inside the IP Office control unit. Each VCM provides a number of voice
compression channels 46 , indicated by a number suffix. For example, a VCM 8 has 8 voice compression channels.
· For the IP500 control unit, to use an IP400 Voice Compression Card an IP500 Carrier Card 214 is also required for
each IP400 VCM. For IP500 control units, voice compression channels can also be added using up to 2 IP500 VCM
base cards with VCM licenses 216 .
VCM Cards
25ms echo
cancellation.
64ms echo
cancellation.
SAP Code
IP500
IP500v2
IP400 VCM5*
700185119
–
–
IP400 VCM10*
700185127
–
–
IP400 VCM20*
700185135
–
–
IP400 VCM30
700293939
IP400 VCM4
700359854
IP400 VCM8
700359862
IP400 VCM16
700359870
IP400 VCM24
700359888
2
2
128
148
Number of IP400 VCM cards.
Maximum number of channels.
1. These modules are still supported on some systems but are no longer available from Avaya.
IP Office Standard Version Installation
IP Office 7.0
Page 245
15-601042 Issue 23e (16 March 2011)
9.9 IP400 Expansion Modules
The following IP400 external expansion modules are supported by IP Office Release 7.0 and can be used with an IP500
and IP500v2 control units. Each module uses an external power supply unit 33 supplied with the module. A locale
specific power cord 34 for the PSU must be ordered separately.
If being rack mounted these units use the IP400 rack mounting kit. If being rack mounted, these units use the IP500 rack
mounting kit. They cannot be wall mounted.
· IP400 Analog Trunk Module (ATM16) 248
Provides an additional 16 ANALOG 373 ports for connection of analog trunks.
Supports both loop-start and ground-start trunks.
· Available in a number of variants for different locales.
· Use with ground start trunks requires that the trunk module and the IP
Office control unit are grounded.
· IP400 Digital Station Module 252
Provides, depending on the variant, an additional 16 or 30 DS 376 ports for
supported Avaya digital phones. This module has been superseded by the
Digital Station V2.
· IP400 Digital Station Module V2 250
Provides, depending on variant, an additional 16 or 30 DS 376 ports for
supported Avaya digital phones 43 . Supersedes the previous Digital Station
module.
· IP400 Phone Module 256
Provides, depending on variant, an additional 8, 16 or 30 POT 382 ports for
analog phones. This module has been superseded by the Phone Module V2.
· IP400 Phone Module V2 254
Provides, depending on variant, an additional 8, 16 or 30 PHONE 382 ports for
analog phones. Supersedes the previous Phone module. With IP Office 3.1,
the Phone V2 supports a wider range of message waiting indication (MWI)
options than Phone V1 modules.
· With V2 units, the labeling of analog phone ports was changed from POT to
PHONE.
IP Office Standard Version Installation
IP Office 7.0
Page 246
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
· IP400 So8 Module 258
Provides 8 ETSI BRI-So 374 ports for the connection of ISDN devices. This
unit is not intended to support BRI trunks.
IP Office Standard Version Installation
IP Office 7.0
Page 247
15-601042 Issue 23e (16 March 2011)
9.9.1 Analog Trunk 16
The IP400 Analog Trunk module (also known as the ATM16) is used to add 16 additional analog trunks to an IP Office
system. The module supports both loop-start and, with suitable grounding, ground-start trunks.
· IMPORTANT
In all IP Office installations, any module being used for analog trunk connections must be connected to a functional
earth 38 .
·
WARNING
Within the Republic of South Africa and in areas of high lightning risk, any module using analog trunk connections must
be connected to a protective ground 38 and to surge protection equipment 39 .
Feature
Details
Supported on
All IP Office control units except Small Office Edition.
Locales
Specific variants are provided for different IP Office locales, see below.
Software Level
IP Office core software level 1.0 minimum. Bin file = naatm16.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a 2-pin, 40W external power supply unit. The PSU has an integral
power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C7 power
cord 33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP400 Rack
Mounting Kit.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 2.9Kg/6.6lbs. Boxed: 4.2Kg/9.4lbs.
IP Office Standard Version Installation
IP Office 7.0
Page 248
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
Ports
Description
ANALOG
DC I/P
DTE
DC power input port. Used for connection of the power lead from an Avaya 40W external power supply
unit supplied with the expansion module. A locale specific IEC60320 C7 power cord 33 for the
external PSU is required but is not supplied with the module.
376
25-Way D-Type socket. For Avaya use only.
144
EXPANSION
PF
RJ45 socket. Used for connection to analog trunks. Ports can be configured as either loop-start or
ground-start trunks through the IP Office configuration.
In the event of power failure, Analog ports 1 and 2 are directly connected to analog extension ports
PF1 and PF2 respectively. If used the connected phones must be clearly labeled as power failure
devices. This is only supported for loop-start analog trunks.
373
381
379
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
RJ45 socket. Power failure analog extension ports. See Analog section above.
Ground point. Used for connection of a functional earth 38 if required. On older modules where this
screw is not present, the top-center cover screw should be used instead.
· IMPORTANT
In all IP Office installations, any module being used for analog trunk connections must be connected
to a functional earth 38 .
·
WARNING
Within the Republic of South Africa and in areas of high lightning risk, any module using analog
trunk connections must be connected to a protective ground 38 and to surge protection equipment
39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP400 Analog Trunk 16
America
America
700211360
Europe
Europe
700241680
New Zealand
New Zealand
700241698
CEE7/16
Europe
700213382
BS1363
United Kingdom
700213374
NEMA1-15
America
700213390
Korea
Korea
700254519
All
700210800
IEC60320 C7 Power Cord
IP400 Rack Mounting Kit
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 249
15-601042 Issue 23e (16 March 2011)
9.9.2 Digital Station V2
The IP400 Digital Station V2 (also known as DS V2) is used to add additional DS ports to an IP Office system. The DS V2
is available in 16 and 30 port variants, referred to as DS16 V2 and DS30 V2 respectively.
The DS V2 supersedes the original IP400 Digital Station, now referred to as a DS V1. The module version is indicated by
labels both the base and the rear of the module.
Feature
Details
Supported on
All IP Office control units except Small Office Edition.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 2.1(31) minimum. Bin file = nadcpV2.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply module. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP400 Rack
Mounting Kit.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30 V2)
IP Office Standard Version Installation
IP Office 7.0
Page 250
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
Ports
DC I/P
DS
Description
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external power
supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord 33 for the
external PSU is required but is not supplied with the module.
376
RJ45 socket. Digital Station port. Used for connection of IP Office supported DS phones 43 .
If connected to an out-of-building extension 39 , the connection must be made via additional IROB
barrier devices in addition to the buildings primary protection. The module must also be connected to a
protective ground.
376
DTE
9-Way D-Type socket. For Avaya use only.
144
EXPANSION
379
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 38 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP400 Digital Station V2
16 Ports
All
700359839
30 Ports
IEC60320 C13 Power Cord
IP400 Rack Mounting Kit
700359847
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
All
700210800
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 251
15-601042 Issue 23e (16 March 2011)
9.9.3 Digital Station
The IP400 Digital Station module (also known as DS module) is used to add additional DS ports to an IP Office system.
The DS module is available in 16 and 30 port variants, referred to as DS16 and DS30 modules respectively. The IP400
Digital Station Module has been superseded by the IP400 Digital Station Module V2 250 .
Feature
Details
Supported on
All IP Office control units except Small Office Edition.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 1.0 minimum. Bin file = nadcp-16.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a 2-pin, 40W external power supply unit. The PSU has an integral
power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C7 power cord
33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP400 Rack
Mounting Kit.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30).
IP Office Standard Version Installation
IP Office 7.0
Page 252
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
Digital Station Module Connections
Ports
DC I/P
DS
Description
DC power input port. Used for connection of the power lead from an Avaya 40W external power
supply unit supplied with the expansion module. A locale specific IEC60320 C7 power cord 33 for the
external PSU is required but is not supplied with the module.
376
Digital Station port. Used for connection of IP Office supported DS phones 43 .
If connected to an out-of-building extension 39 , the connection must be made via additional IROB
barrier devices in addition to the buildings primary protection. The module must also be connected to
a protective ground.
376
DTE
25-Way D-Type socket. For Avaya use only.
144
EXPANSION
379
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Ground point. Used for connection of a protective or functional ground 194 if required. On older
modules where this screw is not present, the top-center cover screw should be used instead.
Must be connected if any out-of-building extensions 39 are connected to this module.
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP400 Digital Station
16 Ports
All
700184807
30 Ports
IEC60320 C7 Power Cord
IP400 Rack Mounting Kit
700184880
CEE7/16
Europe
700213382
BS1363
United Kingdom
700213374
NEMA1-15
America
700213390
Korea
Korea
700254519
All
700210800
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 253
15-601042 Issue 23e (16 March 2011)
9.9.4 Phone V2
The IP400 Phone V2 module (also known as the Phone V2 module) is used to add additional PHONE ports to an IP Office
system. PHONE ports are used for analog phones.
The Phone V2 module is available in 8, 16 and 30 port variants, referred to as the Phone 8, Phone 16 and Phone 30
respectively.
The Phone V2 module supersedes the original IP400 Phone module, now referred to as the Phone V1. The module version
is indicated by labels on both the base and the rear of the module. Key changes are:
· The Phone V2 uses an earthed 3-pin 60W external power supply unit.
· With IP Office 3.1, the message waiting indication (MWI) on each port can be configured for None, On, 51V Stepped,
81V, Line Reversal A or Line Reversal B. On uses the default determined by the system locale. Ports on a Phone V2
module can additionally be configured for 101V operation.
· These ports do not include a ringing capacitor. Therefore for connection to 4-wire analog phones where this is a
requirement (typically the United Kingdom and New Zealand), connection should be via a Master socket containing
ringing capacitors.
· The DTE serial port on the rear of the module has been changed to a 9-pin D-type socket.
Feature
Details
Supported on
All IP Office control units except Small Office Edition.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 2.1(36) minimum. Bin file = dvpots.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply unit. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP400 Rack
Mounting Kit.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 3.1Kg/6.94lbs. Boxed: 4.4Kg/9.7lbs. (Based on Phone 30 V2)
IP Office Standard Version Installation
IP Office 7.0
Page 254
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
Phone Module V2 Connections
Ports
DC I/P
DTE
Description
376
9-Way D-Type socket. For Avaya use only.
144
EXPANSION
379
PHONE
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external power
supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord 33 for the
external PSU is required but is not supplied with the module.
382
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
RJ45 socket. Used for connection of analog phones. Intended for two-wire analog phones. For connection
to 4-wire analog phones connection should be via a master socket with ringing capacitors.
If connected to an out-of-building extension 39 , the connection must be made via additional IP Office
Barrier Boxes 133 in addition to the buildings primary protection. The module must also be connected to a
protective ground.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 194 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 39 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP400 Phone V2
8 Ports
All
700359896
16 Ports
700359904
30 Ports
IEC60320 C13 Power Cord
IP400 Rack Mounting Kit
700359912
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
All
700210800
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 255
15-601042 Issue 23e (16 March 2011)
9.9.5 Phone
The IP400 Phone module (also known as the Phone V1 module) is used to add additional POT ports to an IP Office system.
POT ports are used for analog phones.
The Phone module is available in 8, 16 and 30 port variants, referred to as the Phone 8, Phone 16 and Phone 30
respectively. The IP400 Phone Module has been superseded by the Phone Module V2 254 .
· With IP Office 3.1 and higher, the message waiting indication (MWI) on each POT port can be configured for None, On,
51V Stepped, 81V, Line Reversal A or Line Reversal B. On uses the default determined by the system locale. POT ports
on a Phone V2 module can additionally be configured for 101V operation.
Feature
Details
Supported on
All IP Office control units except Small Office Edition.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 1.0 minimum. Bin file = napots16.bin (earlier units, not supported on
IP500) or avpots16.bin (later units).
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a 2-pin, 40W external power supply unit. The PSU has an integral
power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C7 power cord
33 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP400 Rack
Mounting Kit.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 3.1Kg/6.94lbs. Boxed: 4.4Kg/9.7lbs. (Based on Phone 30 V2).
IP Office Standard Version Installation
IP Office 7.0
Page 256
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
Phone V1 Module Connections
Ports
DC I/P
DTE
Description
25-Way D-Type socket. For Avaya use only.
144
EXPANSION
POT
DC power input port. Used for connection of the power lead from an Avaya 40W external power
supply unit supplied with the expansion module. A locale specific IEC60320 C7 power cord 33 for the
external PSU is required but is not supplied with the module.
376
382
379
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
RJ45 socket. Used for connection of analog phones.
If connected to an out-of-building extension 39 , the connection must be made via additional IP Office
Barrier Box devices in addition to the buildings primary protection. The module must also be
connected to a protective ground.
Function ground point. Used for connection of a protective or functional ground 194 if required. On
older modules where this screw is not present, the top-center cover screw should be used instead.
Must be connected if any out-of-building extensions 39 are connected to this module.
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP400 Phone V1
8 Ports
All
700184773
16 Ports
700184781
30 Ports
IEC60320 C7 Power Cord
IP400 Rack Mounting Kit
700184799
CEE7/16
Europe
700213382
BS1363
United Kingdom
700213374
NEMA1-15
America
700213390
Korea
Korea
700254519
All
700210800
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Standard Version Installation
IP Office 7.0
Page 257
15-601042 Issue 23e (16 March 2011)
9.9.6 So8
The So8 module is used to add ETSI BRI S0-interface ports to the IP Office system. These ports can then be used for the
connection of ISDN devices.
Feature
Details
Supported on
All IP Office control units except Small Office Edition.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 1.0 minimum. Bin file = nas0-16.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The unit is supplied with an earthed 3-Pin, 60W external power supply unit. The PSU has an integral
power cord for connection to the unit's DC I/P socket. A locale specific IEC60320 C13 power cord
33 for the external PSU is required but is not supplied with the unit.
· Older units were supplied with a 2-Pin, 40W external power supply unit which used a locale
specific locale specific IEC60320 C7 power cord 33 .
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP400 Rack
Mounting Kit.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8"/2U.
Weight
Unboxed: 2.8Kg/6.3lbs. Boxed: 4.1Kg/9.2lbs.
IP Office Standard Version Installation
IP Office 7.0
Page 258
15-601042 Issue 23e (16 March 2011)
System Components: IP400 Expansion Modules
So8 Module Connections
Ports
Description
BRI
RJ45 socket. Used for connection of ISDN terminal devices.
374
Note: These ports appear a lines within the IP Office configuration. However they cannot be used for
connection to external BRI lines.
DC I/P
DTE
376
144
EXPANSION
379
DC power input port. Used for connection of the power lead from an Avaya 60W external power supply
unit supplied with the expansion module. A locale specific IEC60320 C13 power cord 33 for the external
PSU is required but is not supplied with the module.
25-Way D-Type socket. For Avaya use only.
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Function ground point. Used for connection of a protective or functional ground 38 if required. On older
modules where this screw is not present, the top-center cover screw should be used instead.
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system. Expansion modules include an external power supply unit (PSU) and an appropriate
interconnect cable. They do not include a locale specific power cord for the external PSU or any phone extension cables.
Item
Variant
IP400 So8
IEC60320 C13 Power Cord
IP400 Rack Mounting Kit
IP Office Standard Version Installation
IP Office 7.0
Country
SAP Code
All
700185077
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
All
700210800
Page 259
15-601042 Issue 23e (16 March 2011)
9.10 Mounting Kits
The following mounting kits are available for use with IP Office systems.
9.10.1 IP500 Wall Mounting Kits
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings.
In addition to the existing environmental requirements
apply when wall mounting a unit:
54
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Standard Version Installation
IP Office 7.0
Page 260
15-601042 Issue 23e (16 March 2011)
System Components: Mounting Kits
9.10.2 IP500 Rack Mounting Kit
· IP500 Rack Mounting Kit (SAP 700429202)
This kit contains all the components required for the rack mounting of
a single IP500v2 control unit, IP500 control unit or IP500 external
expansion module. This includes screws for fixing of the brackets to
the module, bolts for securing the module in the rack and cable tidy
brackets.
9.10.3 IP400 Rack Mounting Kit
· IP400 Rack Mounting Kit (SAP 700210800)
This kit contains all the components required for the rack mounting of
a single control unit or expansion module. This includes screws for
fixing of the brackets to the module and bolts for securing the module
in the rack.
9.10.4 Barrier Box Rack Mounting Kit
· Barrier Box Rack Mounting Kit (SAP 700293905)
Barrier boxes must be used for out-of-building analog phone
extensions 39 . This bracket allows up to 8 IP Office barrier boxes to
be rack mounted and simplifies the number of connections to the
protective ground point in the rack. This kit must be used when more
than 3 barrier boxes are in use and supports a maximum of 16
barrier boxes for a single external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 261
15-601042 Issue 23e (16 March 2011)
9.11 Phones
IP Office Release 7.0 supports the following phones and phone add-ons. Availability may depend on location and may be
subject to local restrictions.
Enhanced Tip and Ring (ETR Port)
These phones are only supported on an ETR6 card in a IP500v2 systems. They are only supported in IP Office Essential
Edition - PARTNER® Version and IP Office Essential Edition - Quick Version mode systems running a North American
locale. They are not supported in IP Office Essential Edition - Norstar Version and IP Office Standard modes.The following
are supported in mode.
· ETR Series: ETR6 322 , ETR6D 322 , ETR18
2 per card and 4 in total)
· PARTNER DECT: 3910 290 , 3920 290
323 ,
ETR18D
323 ,
ETR34D
324
(ETR 34D phones limited to a maximum of
Digital Station (DS Port)
These digital stations connect to the IP Office via DS 376 ports. The following are supported in IP Office Essential Edition PARTNER® Version, IP Office Essential Edition - Norstar Version, IP Office Essential Edition - Quick Version and IP Office
Standard Version modes.
· 1400 Series: 1403
· 9400 Series: 9404
· 9500 Series: 9504
266 ,
267 ,
308 ,
1408
9408
309 , 9508
308
1416
268
309
The following are only supported in IP Office Standard Version mode:
· 2400 Series: 2402 275 , 2410 276 , 2420 277 .
· 3800 Series: 3810 Wireless phone 289 .
· 4400 Series: 4406D 291 , 4412D+ 292 , 4424D+ 293 (Not supported on the IP500 and IP500v2 control unit DS
ports)
· 5400 Series: 5402 300 , 5410 301 , 5420 302 .
· T3 (Upn) Series: T3 Compact 336 , T3 Classic 334 , T3 Comfort 335 .
Digital Station (TCM Port)
These digital stations connect to the IP500v2 IP Office system via TCM 385 ports. The following are supported in IP Office
Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version, IP Office Essential Edition - Quick
Version and IP Office Standard Version modes.
· 4100 Series: 4135, 4136, 4145, 4145EX, 4146, 4146EX - Connection to IP Office TCM ports via a Digital Mobility
Solution 349 system.
· 7400 Series: 7420, 7430, 7434, 7439, 7440, 7444, 7449 - Connection to IP Office TCM ports via a Digital Mobility
Solution 349 system.
· ACU: Audio Conferencing Unit 321
· M-Series: MT7100 325 , MT7100N 325 , MT7208 326 , MT7208N 326 , M7310 327 , M7310N 327 , M7324 328 , M7324N 328
.
· T-Series: T7000 329 , T7100 329 , T7208 330 , T7316 331 , T7316E 332 , T7406 333 , T7406E 333
IP Telephones
IP Phones (SIP and H323) connect to the IP Office system via the RJ45 LAN or WAN. These device require an Avaya IP
Endpoint license and voice compression resources. They are not supported in IP Office Essential Edition - PARTNER®
Version, IP Office Essential Edition - Norstar Version and IP Office Essential Edition - Quick Version mode.
H323:
· 1600 Series: 1603IP/SW 269 , 1608 271 , 1608-I 271 , 1616 273 , 1616-I 273
· 3600 Series: 3616 278 , 3620 279 , 3626 280 , 3641 281 , 3645 282
· 3700 Series: 3701 283 , 3711 284 - Connection via DECT base stations. 3720 285 , 3725 286 , 3740 287 , 3749 288 Connection via DECT R4 base stations.
· 4600 Series: 4601 294 , 4602 295 , 4602SW 295 , 4610 296 , 4610SW 296 , 4620 297 , 4620SW 297 , 4621SW 298 , 4625
299 .
· 5600 Series: 5601 303 , 5602 304 , 5602SW 304 , 5610 305 , 5620 306 , 5621 307 .
· 9600 Series: 9608 310 , 9620L 311 , 9620C 311 , 9621G 313 , 9630G 314 , 9640 316 , 9640G 316 , 9641G 318 , 9650 319 ,
9650C 319
· T3 IP Series: T3 IP Compact 336 , T3 IP Classic 334 , T3 IP Comfort 335 .
IP Office Standard Version Installation
IP Office 7.0
Page 262
15-601042 Issue 23e (16 March 2011)
System Components: Phones
SIP:
·
·
·
·
1000 Series: 1010 264 , 1040 264
1100 Series: 1120E 265 , 1140E 265
1200 Series: 1220 265 , 1230 265
Softphone: Avaya IP Office SIP Softphone application.
Analog Telephones
Analog phones and devices connect to PHONE 382 ports with the IP Office system. However due to the variety of analog
phones and device available no guarantee of operation is given. It is the responsibility of the IP Office installer and
maintainer to test and verify the operation of proposed analog equipment.
· 6200 Series: 6211, 6219, 6221 (North America).
· Interquartz Gemini: 9330-AV, 9335-AV, 9281-AV (Europe, Middle East, Africa, Asia-Pacific).
IP Office Standard Version Installation
IP Office 7.0
Page 263
15-601042 Issue 23e (16 March 2011)
9.11.1 1010/1040
The 1000 Series phones are high-quality SIP video phone devices. The 1010 and 1040 phones are supported. Each
consists of a main module to which a range of video camera and microphone/speaker devices can be attached. The main
module provides outputs for display of video on HD video compatible devices
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
1010 Main module with camera, mircrophone and remote control
IP Office Standard Version Installation
IP Office 7.0
Page 264
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.2 1120/1140/1220/1230
These Avaya SIP telephones are supported by IP Office Release 6.1 and higher.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
1120 Telephone
1120 Telephone
IP Office Standard Version Installation
IP Office 7.0
1140 Telephone
1140 Telephone
Page 265
15-601042 Issue 23e (16 March 2011)
9.11.3 1403
This phone is supported with IP Office Release 6.0 and higher.
1603
Feature
1403
Connects via
DS port.
IP Office Release
6.0
Programmable Buttons
3
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
2 x 16 backlit.
Supported Add-Ons
None
Upgradeable Firmware
Fixed Telephony Function Keys
SPEAKER
MESSAGE
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
TRANSFER
CONFERENCE
Variant
1403 Telephone
IP Office Standard Version Installation
IP Office 7.0
CONTACTS
VOLUME DOWN
CALL LOG
MENU
SAP Code
Black
700469927
Page 266
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.4 1408
This phone is supported with IP Office Release 6 and higher.
1408
Feature
1408
Connects via
DS port.
IP Office Release
6.0+
Programmable Buttons
8
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
3 x 24
backlit.
Supported Add-Ons
None.
Upgradeable Firmware
Fixed Function Keys
SPEAKER
MESSAGE
DROP
HEADSET
HOLD
REDIAL
MUTE
TRANSFER
CONFERENCE
Variant
1408 Telephone
IP Office Standard Version Installation
IP Office 7.0
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
SAP Code
Black
700469851
Page 267
15-601042 Issue 23e (16 March 2011)
9.11.5 1416
This phone is supported with IP Office Release 6 and higher.
1416
Feature
1416
Connects via
DS port.
IP Office Release
6.0+
Programmable Buttons
16
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
4 x 24 Backlit.
Supported Add-Ons
DBM32
341
x 3.
Upgradeable Firmware
Fixed Function Keys
SPEAKER
MESSAGE
DROP
HEADSET
MUTE
HOLD
REDIAL
TRANSFER
CONFERENCE
Variant
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
SAP Code
1416 Telephone
Black
700469869
DBM32 Button Module
Black
700469968
IP Office Standard Version Installation
IP Office 7.0
Page 268
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.6 1603
This phone is supported with IP Office 4.2 and higher. Support for the 1603SW model was added in IP Office 5.0. Support
for the I variants was added in IP Office Release 6.0 and in 5.0 maintenance releases.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
1603
Feature
1603-I
Connects via
IP network.
IP Office Release
4.2 Q4 2008 5.0+
+
Programmable Buttons
1603SW-I
3
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Class 2
Power Consumption
(4.3W)
Class 2
(4.3W)
Display
2 x 16 backlit.
Supported Add-Ons
None
Upgradeable Firmware
PC Pass-Through Port/
with Voice Priority
/
/
Fixed Telephony Function Keys
SPEAKER
MESSAGE
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
CONFERENCE
Material Description
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
Code
Phones (Ethernet cord sold separately. Local power sold separately. PoE adapter sold
separately.)
1603IP Phone
700415540
1603SW Phone
700458508
1603-I Telephone
700476849
1603SW-I Telephone
700458524
Replacement Wedge Stand
700415615
Accessories
CAT5 Ethernet Cable (14 ft)
700383326
CAT5 Ethernet Cable (1 ft)
700436710
Power Adapters
1603 PoE adapter
700415607
Power Adapter for 1600 IP Phones 5V US
700451230
Power Adapter for 1600 IP Phones 5V UK
700451248
Power Adapter for 1600 IP Phones 5V EU
700451255
Power Adapter for 1600 IP Phones 5V ARGENTINA
700451263
IP Office Standard Version Installation
IP Office 7.0
Page 269
15-601042 Issue 23e (16 March 2011)
Material Description
Code
Power Adapter for 1600 IP Phones 5V KOREA
700451271
Power Adapter for 1600 IP Phones 5V CHINA
700451289
Power Adapter for 1600 IP Phones 5V AUSTRALIA
700451297
Labels
1603 Paper DESI Labels - Pack of 50 Labels (8.5" x 11")
700415706
1603 Paper DESI Labels - Pack of 50 Labels (A4)
700434210
IP Office Standard Version Installation
IP Office 7.0
Page 270
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.7 1608
This phone is supported with IP Office 4.2 and higher. Support for the I variant was added in IP Office Release 6.0 and in
5.0 maintenance releases.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
1608
Feature
1608
Connects via
IP network.
IP Office Release
4.2 Q4 2008
+
Programmable Buttons
8
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
Class 2
(4.7W)
Display
3 x 24
backlit.
Supported Add-Ons
None.
Upgradeable Firmware
PC Pass-Through Port/with Voice
Priority
/
Fixed Function Keys
SPEAKER
MESSAGE
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
CONFERENCE
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
Material Description
Code
Phones (Ethernet cord sold separately. Local power sold separately. PoE adapter sold
separately.)
1608 IP Phone
700415557
1608-I IP Phone
700458532
Replacement Stand
700415714
Wall Mounting Kit
700415623
Accessories
CAT5 Ethernet Cable (14 ft)
700383326
CAT5 Ethernet Cable (1 ft)
700436710
1608 Wall Mount Kit (Includes 1 ft Ethernet cable and screws)
700415623
Power Adapters
Power Adapter for 1600 IP Phones 5V US
700451230
Power Adapter for 1600 IP Phones 5V UK
700451248
Power Adapter for 1600 IP Phones 5V EU
700451255
Power Adapter for 1600 IP Phones 5V ARGENTINA
700451263
Power Adapter for 1600 IP Phones 5V KOREA
700451271
Power Adapter for 1600 IP Phones 5V CHINA
700451289
Power Adapter for 1600 IP Phones 5V AUSTRALIA
700451297
Labels
IP Office Standard Version Installation
IP Office 7.0
Page 271
15-601042 Issue 23e (16 March 2011)
Material Description
Code
1608 Paper DESI Labels - Pack of 50 Labels (8.5" x 11")
700415649
1608 Paper DESI Labels - Pack of 50 Labels (A4)
700434228
Headsets
HIS Headset Cable for 9600 & 1608/1616 IP Phones
700409881
SupraElite Monaural (One Ear) Voice Tube (HIS cable required)
700343718
SupraElite Monaural (One Ear) Noise Cancelling (HIS cable required)
700343726
SupraElite Monaural (Two Ear) Voice Tube (HIS cable required)
700343734
SupraElite Monaural (Two Ear) Noise Cancelling (HIS cable required)
700343742
AWH-55+ Wireless Headset
700428204
AWH-65+ Wireless Headset - UK
700428212
AWH-65+ Wireless Headset - EURO
700428220
AWH75N Executive Wireless Headset NAR
700446313
AWH75N Executive Wireless Headset EU
700446321
AWH75N Executive Wireless Headset UK
700446339
ABT-35+S Headset & Base - NA
700428170
ABT-35+S Headset & Base - EURO
700428196
IP Office Standard Version Installation
IP Office 7.0
Page 272
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.8 1616
This phone is supported with IP Office 4.2 and higher. Support for the I variant was added in IP Office Release 6.0 and in
5.0 maintenance releases.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
1616
Feature
1616
Connects via
IP network.
IP Office Release
4.2 Q4 2008+
Programmable Buttons
16
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle
Power Consumption
Class 2
Display
4 x 24 Backlit.
Supported Add-Ons
BM32
340
x 3.
Upgradeable Firmware
PC Pass-Through Port/with
Voice Priority
/
Fixed Function Keys
SPEAKER
MESSAGE
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
CONFERENCE
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
Material Description
Code
Phones (Ethernet cord sold separately. Local power sold separately. PoE adapter sold
separately.)
1616 IP Phone
700450190
1616-I IP Phone
700458540
BM32 Button Module for 1616 (includes cable and bridge)
700415573
Replacement Stand
700415722
Accessories
CAT5 Ethernet Cable (14 ft)
700383326
CAT5 Ethernet Cable (1 ft)
700436710
1616 Wall Mount Kit (Includes 1 ft Ethernet cable and screws)
700415631
Power Adapters
Power Adapter for 1600 IP Phones 5V US
700451230
Power Adapter for 1600 IP Phones 5V UK
700451248
Power Adapter for 1600 IP Phones 5V EU
700451255
Power Adapter for 1600 IP Phones 5V ARGENTINA
700451263
Power Adapter for 1600 IP Phones 5V KOREA
700451271
Power Adapter for 1600 IP Phones 5V CHINA
700451289
Power Adapter for 1600 IP Phones 5V AUSTRALIA
700451297
Labels
IP Office Standard Version Installation
IP Office 7.0
Page 273
15-601042 Issue 23e (16 March 2011)
Material Description
Code
1616/BM32 Paper DESI Labels - Pack of 50 Labels (8.5" x 11")
700415656
1616/BM32 Paper DESI Labels - Pack of 50 Labels (A4)
700434236
Headsets
HIS Headset Cable for 9600 & 1608/1616 IP Phones
700409881
SupraElite Monaural (One Ear) Voice Tube (HIS cable required)
700343718
SupraElite Monaural (One Ear) Noise Cancelling (HIS cable required)
700343726
SupraElite Monaural (Two Ear) Voice Tube (HIS cable required)
700343734
SupraElite Monaural (Two Ear) Noise Cancelling (HIS cable required)
700343742
AWH-55+ Wireless Headset
700428204
AWH-65+ Wireless Headset - UK
700428212
AWH-65+ Wireless Headset - EURO
700428220
AWH75N Executive Wireless Headset NAR
700446313
AWH75N Executive Wireless Headset EU
700446321
AWH75N Executive Wireless Headset UK
700446339
ABT-35+S Headset & Base - NA
700428170
ABT-35+S Headset & Base - EURO
700428196
IP Office Standard Version Installation
IP Office 7.0
Page 274
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.9 2402
In addition to the two physical programmable buttons, the
addition 12 programmable slots.
FEATURE key plus 0-9, * and # can be used to access an
On IP Office, the 2402D display is not used.
2402D
Feature
Detail
Connects via
DS port.
IP Office Release
3.0+
Programmable Buttons
2
.
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
Not used.
Supported Add-Ons
None.
Upgradable Firmware
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
VOLUME DOWN
TRANSFER
CONFERENCE
Variant
SAP Code
2402D
Multi-Grey
700381973
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
Page 275
15-601042 Issue 23e (16 March 2011)
9.11.10 2410
2410D
Feature
2410
Connects via
DS port.
IP Office Release
3.0+
Programmable Buttons
12.
(6 buttons x 2 pages).
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
29 characters x 5 lines.
(168 x 80 pixels).
Supported Add-Ons
None.
Upgradable Firmware
Standard DCP Phone Keys
HEADSET
SPEAKER
MESSAGES
HOLD
DROP
REDIAL
VOLUME UP
MUTE
TRANSFER
CONFERENCE
Variant
SAP Code
2410
Multi-Grey
700381999
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
VOLUME DOWN
Page 276
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.11 2420
2420D
Feature
Details
Connects via
DS port.
IP Office Release
1.4+
Programmable Buttons
24 (8 buttons x 3 pages)
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
29 characters x 7 lines.
Supported Add-Ons
EU24*, 201B.
Upgradable Firmware
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
MUTE
HOLD
DROP
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
REDIAL
Variant
SAP Code
2420
Multi-Grey
700381585
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
201B Recorder Interface Module
700381635
20B Stand
700381650
EU24*
Multi-Grey
700381817
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery
backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 277
15-601042 Issue 23e (16 March 2011)
9.11.12 3616
This is an 802.11b WiFi phone. It connects to the IP Office via a wireless access point and Avaya Voice Priority Processor
(AVPP).
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
3616
Feature
Detail
Connects via
IP network.
IP Office Release
2.0+
Programmable Buttons
6.
Headset Socket
Message Waiting Lamp
Upgradable Firmware
Variant
SAP Code
3616 Wireless Phone
700413040
Additional battery pack for 3616
700277387
Desktop charger for 3616.
700412901
Clip for 3616
700413057
3616/3626 Configuration Cradle
700375934
IP Office Standard Version Installation
IP Office 7.0
Page 278
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.13 3620
This is an 802.11b WiFi phone. It connects to the IP Office via a wireless access point and Avaya Voice Priority Processor
(AVPP).
The 3620 is similar to the 3616 but has been designed for use in healthcare environments. It is waterproof and has a back
lit display.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
3616
Feature
Detail
Connects via
IP network.
IP Office Release
3.2+
Programmable Buttons
6.
Headset Socket
Message Waiting Lamp
Upgradable Firmware
Variant
SAP Code
3620 Wireless Phone
700413065
Additional battery pack.
700277387
Desktop charger.
700412901
Clip
700413057
Configuration Cradle
700375934
IP Office Standard Version Installation
IP Office 7.0
Page 279
15-601042 Issue 23e (16 March 2011)
9.11.14 3626
This phones is similar to the 3616 in functionality. However the 3626 has a ruggedized construction. This is an 802.11b
WiFi phone. It connects to the IP Office via a wireless access point and Avaya Voice Priority Processor (AVPP).
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
3626
Feature
Detail
Connects via
IP network.
IP Office Release
2.0+
Programmable Buttons
6.
Headset Socket
Message Waiting Lamp
Upgradable Firmware
Variant
SAP Code
3626 Wireless Phone
700413024
Additional battery pack for 3626
700277395
Desktop charger for 3626
700412919
3626 Gang changer
700412927
Clip for 3626
700413131
3626 Vinyl case with keypad cover
700412984
3626 Carry case
Yellow
700289309
3626 Carry case with keypad cover
Black
700289317
Yellow
700289325
3616/3626 Configuration Cradle
IP Office Standard Version Installation
IP Office 7.0
700375934
Page 280
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.15 3641
The Avaya 3641 IP Wireless Telephone is a WiFi telephone that runs using H.323.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
The 3641 supports the following features:
· Lightweight innovative design .
· Simple to use.
· 802.11a, 802.11b and 802.11g standard-compatible.
· Transmission type Direct Sequence Spread Spectrum (DSSS).
· FCC certification Part 15.247.
· Management of telephones via DHCP and TFTP.
· Voice encoding G711.
· Wired Equivalent Privacy (WEP) - 40bit and 128 bit. WPA-PSK, WPA2-PSK.
· 5x16 character alphanumeric, plus status indicators.
· 4 hours talk time and 80 hours standby. Extendable with optional battery packs to 8 hours talk time and 160 hours
standby.
IP Office Standard Version Installation
IP Office 7.0
Page 281
15-601042 Issue 23e (16 March 2011)
9.11.16 3645
The Avaya 3645 IP Wireless Telephone is a WiFi telephone that runs using H.323.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
The 3645 supports the following features:
· Lightweight innovative design .
· Simple to use.
· 802.11a, 802.11b and 802.11g standard-compatible.
· Transmission type Direct Sequence Spread Spectrum (DSSS).
· FCC certification Part 15.247.
· Management of telephones via DHCP and TFTP.
· Voice encoding G711.
· Wired Equivalent Privacy (WEP) - 40bit and 128 bit. WPA-PSK, WPA2-PSK.
· 5x16 character alphanumeric, plus status indicators.
· 4 hours talk time and 80 hours standby. Extendable with optional battery packs to 8 hours talk time and 160 hours
standby.
· Can be enabled for Push-to-talk (walkie-talkie) feature for broadcast between employees.
IP Office Standard Version Installation
IP Office 7.0
Page 282
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.17 3701
The 3701 is an Avaya DECT handset supported on IP Office when using Avaya IP DECT base stations.
3701
Feature
Detail
Connects via
IP network
IP Office Release
3.1+
Programmable Buttons
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Upgradable Firmware
Variant
SAP Code
3701
700346802
Belt Clip
700346885
Phone Charger
Power Adaptor for Charger
700346828
European
700346836
UK
700346844
Australia
700378318
8-Phone Gang Charger
Power Adaptor for Rack Mount Charger
IP Office Standard Version Installation
IP Office 7.0
700346851
Global
700346869
Page 283
15-601042 Issue 23e (16 March 2011)
9.11.18 3711
The 3711 is an Avaya DECT handset supported on IP Office when using Avaya IP DECT base stations.
3711
Feature
Detail
Connects via
IP network
IP Office Release
3.1+
Programmable Buttons
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Upgradable Firmware
Variant
SAP Code
3711
700346810
Belt Clip
700346885
Phone Charger
700346828
Power Adaptor for Charger
European
700346836
UK
700346844
Australia
700378318
8-Phone Gang Charger
Power Adapator for Rack Mount
Charger
IP Office Standard Version Installation
IP Office 7.0
700346851
Global
700346869
Page 284
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.19 3720
This DECT handset is supported with Avaya DECT R4 on IP Office Release 5 and higher.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
IP Office Standard Version Installation
IP Office 7.0
Page 285
15-601042 Issue 23e (16 March 2011)
9.11.20 3725
This DECT handset is supported with Avaya DECT R4 on IP Office Release 5 and higher.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
IP Office Standard Version Installation
IP Office 7.0
Page 286
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.21 3740
The 3740 is supported with Avaya DECT R4 systems and IP Office Release 7.0 and higher.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
IP Office Standard Version Installation
IP Office 7.0
Page 287
15-601042 Issue 23e (16 March 2011)
9.11.22 3749
The 3746 is a ruggedized DECT handset. It is supported with Avaya DECT R4 systems and IP Office Release 7.0 and
higher.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
IP Office Standard Version Installation
IP Office 7.0
Page 288
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.23 3810
The phone uses a wireless 900MHz digital protocol to connect to its base station. The base station connects to an IP Office
DS port. The base station also requires a power outlet socket. Additional power outlet sockets are required for the phone
charger.
Depending on coverage overlap, between three and five 3810s can be connected to the same IP Office.
This phone is supported in North America only.
3810
Feature
Detail
Connects via
DS port.
IP Office Release
2.1+
Programmable Buttons
4.
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Upgradable Firmware
Item
SAP Code
3810 Set - Includes phone, base station, charger, belt clip and power supply units for charger and base
station.
700305105
IP Office Standard Version Installation
IP Office 7.0
Page 289
15-601042 Issue 23e (16 March 2011)
9.11.24 3910
This single station DECT phone is supported on an IP500v2 control unit running in Partner Version mode. The base station
uses an ETR port for connection to the IP Office. This phone is no longer available from Avaya and has been superseded by
the 3920 290 .
9.11.25 3920
This single station DECT phone is supported on an IP500v2 control unit running in Partner Version mode. The base station
uses an ETR port for connection to the IP Office.
IP Office Standard Version Installation
IP Office 7.0
Page 290
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.26 4406
This phone is supported in North America only (U-Law only). Not supported on the IP500 Digital Station card.
4406D+
Feature
Detail
Connects via
DS port.
IP Office Release
1.0+
Programmable Buttons
6
.
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
16 characters x 2 lines.
Supported Add-Ons
None.
Upgradable Firmware
Standard DCP Phone Keys
HEADSET
SPEAKER
MESSAGES
HOLD
DROP
REDIAL
VOLUME UP
MUTE
TRANSFER
CONFERENCE
Item
SAP Code
4406D+ (Black)
108199027
4406D+ (White)
108199019
Small 4400 Series Stand (Black)
108541194
Stand 4400 Series Stand (White)
108541202
IP Office Standard Version Installation
IP Office 7.0
VOLUME DOWN
Page 291
15-601042 Issue 23e (16 March 2011)
9.11.27 4412
This phone is supported in North America only (U-Law only). Not supported on the IP500 Digital Station card.
Note: A maximum of twenty-seven 4412D telephones are supported on the IP500 DS30 expansion modules and on IP400
DS30 (version 2) expansion module at PCS level 5. Earlier IP400 DS30 expansion modules will only support sixteen of
these telephones.
4412D+
Feature
Detail
Connects via
DS port.
IP Office Release
1.0+
Programmable Buttons
24 (12
).
/12
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
24 characters x 2 lines.
Supported Add-Ons
4450
339
x 2.
Upgradable Firmware
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
TRANSFER
CONFERENCE
Item
4412D+
Large 4400 Series Stand for 4412D+/4424D+
IP Office Standard Version Installation
IP Office 7.0
VOLUME DOWN
SAP Code
Black
108199050
White
108199043
Black
108541269
White
108541277
Page 292
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.28 4424
This phone is supported in North America only (U-Law only). Not supported on the IP500 Digital Station card.
Note: A maximum of twenty-seven 4424D telephones are supported on the IP500 DS30 expansion modules and on IP400
DS30 (version 2) expansion module at PCS level 5. Earlier IP400 DS30 expansion modules will only support sixteen of
these telephones.
4424D+
Feature
Detail
Connects via
DS ports.
IP Office Release
1.0+
Programmable Buttons
24
.
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
24 characters x 2 lines.
Supported Add-Ons
4450
339
x 2.
Upgradeable Firmware
Standard DCP Phone Keys
HEADSET
SPEAKER
MESSAGES
HOLD
DROP
REDIAL
VOLUME UP
MUTE
TRANSFER
CONFERENCE
Item
4424D+
Large 4400 Series Stand for 4412D+/4424D+
4450 DSS Add-On
Small 4400 Series Stand for 4450.
Power Supply for 4450
IP Office Standard Version Installation
IP Office 7.0
VOLUME DOWN
SAP Code
Black
108199084
White
108199076
Black
108541269
White
108541277
Black
108199696
White
108199407
Black
108541194
White
108541202
108596412
Page 293
15-601042 Issue 23e (16 March 2011)
9.11.29 4601
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or an 802.3af Power over Ethernet (PoE) source. For RoHS compliance the 4601 has been replaced by the 4601+,
however the two phones are functionally the same.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
4601+
Feature
Detail
Connects via
IP Network.
IP Office Release
3.0+
Programmable Buttons
2
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
3.5W (Class 2)
Display
None.
Supported Add-Ons
None.
Upgradeable Firmware
PC Pass-Through Port/with Voice Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
VOLUME DOWN
TRANSFER
CONFERENCE
Variant
SAP Code
4601+
Multi-Grey
700381890
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia and New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
Page 294
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.30 4602
These phones are similar in physical appearance and functions. However the 4602SW+ includes a PC data pass-through
port which gives priority to phone traffic. The 4602IP is no longer available from Avaya.
The 4602SW+ is the RoHS compliant replacement for the 4602SW which is no longer available.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
4602/4602SW
Feature
4602IP
Connects via
IP network.
IP Office Release
1.3+
Programmable Buttons
4602SW+
2
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
3.5W (Class 2)
Display
24 characters x 2 lines.
Supported Add-Ons
None.
Upgradable Firmware
PC Pass-Through Port/with Voice Priority
/
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
MUTE
HOLD
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
REDIAL
Variant
SAP Code
4602IP
Multi-Grey
700221260
4602SW+
Multi-Grey
700381916
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia and New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
Page 295
15-601042 Issue 23e (16 March 2011)
9.11.31 4610
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
4610SW
Feature
Detail
Connects via
IP network.
IP Office Release
3.0+
Programmable Buttons
24 (6 buttons x 4pages).
Headset Socket
Handsfree Speaker/Microphone
/
.
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
4.0W (Class 2)
Display
29 characters x 5 lines
(168 x 80 pixels)
Supported Add-Ons
None.
Upgradable Firmware
PC Pass-Through Port/with Voice Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
MUTE
HOLD
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
REDIAL
Variant
SAP Code
4610SW
Multi-Grey
700381957
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord.
USA
405362641
Europe
407786623
Australia and New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
Page 296
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.32 4620
These phones are similar in physical appearance and functions. However the 4620SW's PC data pass-through port gives
priority to phone traffic.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
4620IP/4620SW
Feature
4620IP
Connects via
IP network.
IP Office Release
2.0+
Programmable Buttons
4620SW
24 (12 buttons x 2 pages).
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
4W (Class 3)
5.9W (Class 3)
Display
29 characters x 7 lines
(168 x 132 pixels)
Supported Add-Ons
EU24*, EU24BL*.
Upgradeable Firmware
PC Pass-Through Port/with Voice
Priority
/
/
Standard DCP Phone Keys
HEADSET
SPEAKER
MESSAGES
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
4620IP
Multi-Grey
700212186
4620SW
Multi-Grey
700259674
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24
Multi-Grey
700381817
EU24BL
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 or EU24BL unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 297
15-601042 Issue 23e (16 March 2011)
9.11.33 4621
The 4621 is similar in physical appearance and function to the 4620SW. However the 4621SW includes a backlight
function for the screen.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
4621SW
Feature
4621SW
Connects via
IP network.
IP Office Release
3.0(577)+
Programmable Buttons
24 (12 buttons x 2 pages).
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power Consumption 5.75W (Class 2)
Display
29 characters x 7 lines
(168 x 132 pixels)
Supported Add-Ons
EU24*, EU24BL*.
Upgradeable Firmware
PC Pass-Through Port/with Voice Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
MUTE
HOLD
DROP
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
REDIAL
Variant
SAP Code
4621SW
Multi-Grey
700345192
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24*
Multi-Grey
700381817
EU24BL*
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with
battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 or EU24BL unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 298
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.34 4625
The 4625 is similar in physical appearance and function to the 4621SW. However the 4625SW includes a color display.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
4625SW
Feature
4625SW
Connects via
IP network.
IP Office Release
3.2+
Programmable Buttons
24 (12 buttons x 2 pages).
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
6.45W (Class 3)
Display
29 characters x 7 lines
(168 x 132 pixels)
Supported Add-Ons
EU24*, EU24BL*.
Upgradeable Firmware
PC Pass-Through Port/with Voice
Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
4625SW
Multi-Grey
700381551
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24*
Multi-Grey
700381817
EU24BL*
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 or EU24BL unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 299
15-601042 Issue 23e (16 March 2011)
9.11.35 5402
This phone is similar in physical appearance and functions to the 2402D. However the 5402 phone is only supported on IP
Office.
FEATURE key plus 0-9, * and # can be used to access an
In addition to the two physical programmable buttons, the
addition 12 programmable slots.
5402
Feature
Detail
Connects via
DS port.
IP Office Release
3.0+.
Programmable Buttons
2
.
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
24 characters
x 2 lines.
Supported Add-Ons
None.
Upgradable Firmware
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
VOLUME DOWN
TRANSFER
CONFERENCE
Variant
SAP Code
5402
Multi-Grey
700345309
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
Page 300
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.36 5410
This phone is similar in physical appearance and functions to the 2410. However the 5410 phone is only supported on IP
Office.
5410
Feature
Detail
Connects via
DS port.
IP Office Release
3.0+
Programmable Buttons
12 (6 buttons x 2 pages).
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
29 characters x 5 lines.
(168 x 80 pixels).
Supported Add-Ons
None.
Upgradable Firmware
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
VOLUME DOWN
TRANSFER
CONFERENCE
Variant
SAP Code
5410
Multi-Grey
700345291
5410 (RoHS compliant)
Multi-Grey
700382005
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
IP Office Standard Version Installation
IP Office 7.0
Page 301
15-601042 Issue 23e (16 March 2011)
9.11.37 5420
This phone is similar in physical appearance and functions to the 2420. However the 5420 is only supported on IP Office.
5420D
Feature
Detail
Connects via
DS port.
IP Office Release
3.0+
Programmable Buttons
24 (8 buttons x 3 pages)
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
29 characters x 7 lines.
Supported Add-Ons
EU24*, 201B.
Upgradable Firmware
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
5420D
Multi-Grey
700339823
5420D (RoHS compliant)
Multi-Grey
700381627
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
201B Recorder Interface Module
700381635
20B Stand
700381650
EU24*
Multi-Grey
700381817
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New
Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 302
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.38 5601
This phone is similar in physical appearance and functions to the 4601. However the 5601 phone is only supported on IP
Office. The 5601+ is the RoHS compliant version that has replaced the previous 5601 IP model but is otherwise the same.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
5601
Feature
Detail
Connects via
IP Network.
IP Office Release
3.0+
Programmable Buttons
2
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
3.5W (Class 2)
Display
None.
Supported Add-Ons
None.
Upgradeable Firmware
PC Pass-Through Port/with Voice Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
5601IP
Multi-Grey
700345366
5601+ (RoHS compliant)
Multi-Grey
700381908
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
IP Office Standard Version Installation
IP Office 7.0
Page 303
15-601042 Issue 23e (16 March 2011)
9.11.39 5602
The 5602IP and 5602SW phones are similar in physical appearance and functions. However the 5602SW includes a PC
data pass-through port which gives priority to phone traffic. The 5602IP is no longer available from Avaya. The 5602SW+
is the RoHS compliant version that has replaced the previous 5602SW model but is otherwise the same.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
5602IP/5602SW
Feature
5602IP
Connects via
IP network.
IP Office Release
3.0+
Programmable Buttons
5602SW
2
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power Consumption
4.1W (Class 2)
Display
24 characters x 2 lines.
Supported Add-Ons
None.
Upgradable Firmware
PC Pass-Through Port/with Voice Priority
/
/
Standard DCP Phone Keys
HEADSET
SPEAKER
MESSAGES
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
5602IP
Multi-Grey
700345341
5602SW
Multi-Grey
700381825
5602SW+ (RoHS compliant)
Multi-Grey
700381932
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24
Multi-Grey
700381817
EU24BL
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
IP Office Standard Version Installation
IP Office 7.0
Page 304
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.40 5610
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
5610
Feature
Detail
Connects via
IP network.
IP Office Release
3.0+
Programmable Buttons
24 (6 buttons x 4 pages).
Headset Socket
Handsfree Speaker/Microphone
/
.
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
5W (Class 2)
Display
29 characters x 5 lines
(168 x 80 pixels)
Supported Add-Ons
None.
Upgradable Firmware
PC Pass-Through Port/with Voice
Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
5610SW
Multi-Grey
700345333
5610SW (RoHS compliant)
Multi-Grey
700381965
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24
Multi-Grey
700381817
EU24BL
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
IP Office Standard Version Installation
IP Office 7.0
Page 305
15-601042 Issue 23e (16 March 2011)
9.11.41 5620
This phone is similar in physical appearance and functions to the 4620SW. It is no longer available from Avaya, having
been replaced by the 5621.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
5620
Feature
5620IP
Connects via
IP network.
IP Office Release
3.0+
Programmable Buttons
24 (12 buttons x 2 pages).
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power Consumption 5.9W (Class 3)
Display
29 characters x 7 lines
(168 x 132 pixels)
Supported Add-Ons
EU24*, EU24BL*.
Upgradeable Firmware
PC Pass-Through Port/with Voice Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
DROP
HEADSET
MUTE
HOLD
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
REDIAL
Variant
SAP Code
5620IP
Multi-Grey
700339815
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24*
Multi-Grey
700381817
EU24BL*
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 or EU24BL unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 306
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.42 5621
This phone is similar in physical appearance and functions to the 4621SW.
This phone requires a separate power supply, using either a Avaya 1151D1 or 1151D2 power supply unit and power cord
or a 802.3af Power over Ethernet (PoE) source.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
5621
Feature
5620IP
Connects via
IP network.
IP Office Release
3.2+
Programmable Buttons
24 (12 buttons x 2 pages).
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
5.9W (Class 3)
Display
29 characters x 7 lines
(168 x 132 pixels)
Supported Add-Ons
EU24*, EU24BL*.
Upgradeable Firmware
PC Pass-Through Port/with Voice Priority
/
Standard DCP Phone Keys
SPEAKER
MESSAGES
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
VOLUME UP
VOLUME DOWN
CONFERENCE
Variant
SAP Code
5621SW
Multi-Grey
700345982
5621SW (RoHS compliant)
Multi-Grey
700385982
Replacement Handset
Dark Grey
700203797
Amplified Handset
Dark Grey
700229735
Noisy Location Handset
Dark Grey
700229743
Push to Talk Handset
Dark Grey
700229727
EU24*
Multi-Grey
700381817
EU24BL*
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
*When used with an EU24 or EU24BL unit, a 1151 type power supply unit must be used to power the phone.
IP Office Standard Version Installation
IP Office 7.0
Page 307
15-601042 Issue 23e (16 March 2011)
9.11.43 9404
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 4 physical buttons with red and green LEDs. These can be used for up to 12 programmable features.
9.11.44 9408
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 8 physical buttons with red and green LEDs. These can be used for up to 24 programmable features.
The phones support the addition of up to 3 BM12 button modules supporting an additional 24 programmable features
(using 12 buttons) per module.
IP Office Standard Version Installation
IP Office 7.0
Page 308
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.45 9504
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 4 physical buttons with red and green LEDs. These can be used for up to 12 programmable features.
9.11.46 9508
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 8 physical buttons with red and green LEDs. These can be used for up to 24 programmable features.
The phones support the addition of up to 3 BM12 button modules supporting an additional 24 programmable features
(using 12 buttons) per module.
IP Office Standard Version Installation
IP Office 7.0
Page 309
15-601042 Issue 23e (16 March 2011)
9.11.47 9608
· These phones are supported by IP Office Release 6.1+ on IP500 and IP500v2 systems only. The voice activated
dialing and USB features are not supported.
· The use of the IP Office control unit as the HTTP file server for these phones is not supported. A third-party HTTP
file server must be used.
The phones supports 24 programmable buttons. These can be used for call appearance functions and other IP Office
features.
This phone can be used with up to 3 x SBM24 or 3 x SBM12 button modules for additional programmable buttons. Note
that the different types of button module cannot be mixed on the same phone. Note that attaching button modules may
change the phones PoE class and may require a separate power supply.
IP Office Standard Version Installation
IP Office 7.0
Page 310
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.48 9620L, 9620C
These phones are supported on IP500 and IP500v2 systems running IP Office Release 6.0 and higher. The phones are
supplied with a two-position stand.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
· The voice activated dialing and USB features are not supported.
· For IP Office Release 6.1, these phones are supported running SIP software. When that is the case, the IP Office or
IP Office Manager should not be used as the file server for the phone. Avaya SIP phones require an Avaya IP
Endpoints license.
· The Class requirement of PoE powered phones may be increased if the phone is used with additional equipment
such as a button module.
9620
Feature
9620L
9620C
Connects via
IP network.
IP network.
IP Office Release
6.0+
6.0+
Programmable
Buttons
Soft
buttons.
Soft
buttons.
Headset Socket
Handsfree Speaker/
Microphone
/
/
Message Waiting
Lamp
PoE Class/Typical Idle Class 1
Power Consumption
Class 1
Display
1/4 VGA
Greyscale
1/4 VGA
Color
Supported Add-Ons
–
–
Upgradeable
Firmware
PC Pass-Through
Port/with Voice
Priority
/
/
Fixed Function Keys
HEADSET
SPEAKER
MESSAGE
HOLD
DROP
REDIAL
MUTE
TRANSFER
CONFERENCE
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
FORWARD
Functions for fixed functions keys not present are accessible through display menu soft key functions.
Variant
SAP Code
9620L Telephone
Charcoal Grey
700461197
9620C Telephone
Charcoal Grey
700461205
9620L without faceplate
–
700461239
9620C without faceplate
–
700461247
Replacement Stand
Silver
700416555
Wedge Stand
Charcoal Grey
700383870
Wall Mounting Plate
Charcoal Grey
700383375
Gigabit Adapter
–
700383771
Bluetooth Adapter
–
700383789
IP Office Standard Version Installation
IP Office 7.0
Page 311
15-601042 Issue 23e (16 March 2011)
Replacement Handset
700416548
Amplified Speech Handset
700446370
Replacement Handset Cord (9 feet)
700383318
Replacement Handset Cord (25 feet)
700383821
Replacement Line Cord
700383326
IP Office Standard Version Installation
IP Office 7.0
Page 312
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.49 9621G
· These phones are supported by IP Office Release 6.1+ on IP500 and IP500v2 systems only. The voice activated
dialing and USB features are not supported.
· The use of the IP Office control unit as the HTTP file server for these phones is not supported. A third-party HTTP
file server must be used.
The phones support 24 programmable buttons which are displayed as touchscreen options. These can be used for call
appearance functions and other IP Office features. In addition the phone supports a home screen on which the user can
add up to 8 icons for programmable functions in addition to those icons present through installation configuration.
These phones do not support any button modules.
IP Office Standard Version Installation
IP Office 7.0
Page 313
15-601042 Issue 23e (16 March 2011)
9.11.50 9630G
These phones are supported on IP500 and IP500v2 systems running IP Office Release 6.0 and higher. The phones are
supplied with a two-position stand.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
· The voice activated dialing and USB features are not supported.
· For IP Office Release 6.1, these phones are supported running SIP software. When that is the case, the IP Office or
IP Office Manager should not be used as the file server for the phone. Avaya SIP phones require an Avaya IP
Endpoints license.
· The Class requirement of PoE powered phones may be increased if the phone is used with additional equipment
such as a button module.
9630
Feature
9630
Connects via
IP network.
IP Office Release
6.0+
Programmable Buttons
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle Power
Consumption
Class 2
Display
1/3 VGA Greyscale
Supported Add-Ons
SMB24
345
x 3.
Upgradeable Firmware
PC Pass-Through Port/with
Voice Priority
/
Fixed Function Keys
SPEAKER
MESSAGE
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
CONFERENCE
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
FORWARD
Functions for fixed functions keys not present are accessible through display menu soft key functions.
Variant
SAP Code
9630G Telephone
Charcoal Grey
700405673
9630G without faceplate
–
700408602
SMB24 Button Module
Charcoal Grey
700462518
SMB24 without faceplate
–
700462526
SMB24 Replacement Stand
Silver
700416571
Replacement Stand
Silver
700416563
Wedge Stand
Charcoal Grey
700383888
Wall Mounting Plate
Charcoal Grey
700383383
Gigabit Adapter
–
700383771
Bluetooth Adapter
–
700383789
Replacement Handset
700416548
Amplified Speech Handset
700446370
Replacement Handset Cord (9 feet)
700383318
IP Office Standard Version Installation
IP Office 7.0
Page 314
15-601042 Issue 23e (16 March 2011)
System Components: Phones
Replacement Handset Cord (25 feet)
700383821
Replacement Line Cord
700383326
IP Office Standard Version Installation
IP Office 7.0
Page 315
15-601042 Issue 23e (16 March 2011)
9.11.51 9640, 9640G
These phones are supported on IP500 and IP500v2 systems running IP Office Release 6.0 and higher. The phones are
supplied with a two-position stand.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
· The voice activated dialing and USB features are not supported.
· For IP Office Release 6.1, these phones are supported running SIP software. When that is the case, the IP Office or
IP Office Manager should not be used as the file server for the phone. Avaya SIP phones require an Avaya IP
Endpoints license.
· The Class requirement of PoE powered phones may be increased if the phone is used with additional equipment
such as a button module.
9640
Feature
9640
Connects via
IP network.
IP Office Release
6.0+
Programmable Buttons
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
PoE Class/Typical Idle
Power Consumption
Class 2
Display
1/3 VGA
Greyscale
Supported Add-Ons
SMB24
3.
345
x
Upgradeable Firmware
PC Pass-Through Port/
with Voice Priority
/
Fixed Function Keys
SPEAKER
MESSAGE
HEADSET
HOLD
DROP
REDIAL
MUTE
TRANSFER
CONFERENCE
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
FORWARD
Functions for fixed functions keys not present are accessible through display menu soft key functions.
Variant
SAP Code
9640 Telephone
Charcoal Grey
700383920
9640G Telephone
Charcoal Grey
700419195
9640 without faceplate
–
700408610
9640G without faceplate
–
700429095
SMB24 Button Module
Charcoal Grey
700462518
SMB24 without faceplate
–
700462526
SMB24 Replacement Stand
Silver
700416571
Replacement Stand
Silver
700416563
Wedge Stand
Charcoal Grey
700383888
Wall Mounting Plate
Charcoal Grey
700383383
Gigabit Adapter
–
700383771
IP Office Standard Version Installation
IP Office 7.0
Page 316
15-601042 Issue 23e (16 March 2011)
System Components: Phones
Bluetooth Adapter
–
700383789
Replacement Handset
700416548
Amplified Speech Handset
700446370
Replacement Handset Cord (9 feet)
700383318
Replacement Handset Cord (25 feet)
700383821
Replacement Line Cord
700383326
IP Office Standard Version Installation
IP Office 7.0
Page 317
15-601042 Issue 23e (16 March 2011)
9.11.52 9641G
· These phones are supported by IP Office Release 6.1+ on IP500 and IP500v2 systems only. The voice activated
dialing and USB features are not supported.
· The use of the IP Office control unit as the HTTP file server for these phones is not supported. A third-party HTTP
file server must be used.
The phones support 24 programmable buttons which are displayed as touchscreen options. These can be used for call
appearance functions and other IP Office features. In addition the phone supports a home screen on which the user can
add up to 8 icons for programmable functions in addition to those icons present through installation configuration.
This phone can be used with up to 3 x SBM24 or 3 x SBM12 button modules for additional programmable buttons. Note
that the different types of button module cannot be mixed on the same phone. Note that attaching button modules may
change the phones PoE class and may require a separate power supply.
IP Office Standard Version Installation
IP Office 7.0
Page 318
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.53 9650, 9650C
These phones are supported on IP500 and IP500v2 systems running IP Office Release 6.0 and higher. The phones are
supplied with a two-position stand.
· The availability of VCM (Voice Compression Module) 46 channels is necessary to support IP telephony. For IP Office
6.0+, these phones require an Avaya IP Endpoints 388 license.
· The voice activated dialing and USB features are not supported.
· For IP Office Release 6.1, these phones are supported running SIP software. When that is the case, the IP Office or
IP Office Manager should not be used as the file server for the phone. Avaya SIP phones require an Avaya IP
Endpoints license.
· The Class requirement of PoE powered phones may be increased if the phone is used with additional equipment
such as a button module.
9650
Feature
9650
9650C
Connects via
IP network.
IP network.
IP Office Release
6.0+
6.0+
/
/
Programmable Buttons
Headset Socket
Handsfree Speaker/
Microphone
Message Waiting Lamp
PoE Class/Typical Idle
Power Consumption
Class 2
Class 2
Display
1/3 VGA
Greyscale
1/3 VGA Color
Supported Add-Ons
SMB24
345
x 3. SMB24
345
x 3.
Upgradeable Firmware
PC Pass-Through Port/
with Voice Priority
/
Fixed Function Keys
HEADSET
SPEAKER
MESSAGE
MUTE
HOLD
DROP
REDIAL
TRANSFER
CONFERENCE
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
FORWARD
Functions for fixed functions keys not present are accessible through display menu soft key functions.
Variant
SAP Code
9650 Telephone
Charcoal Grey
700383938
9650C Telepehone
Charcoal Grey
700461213
9650 without faceplate
–
700408628
9650C without faceplate
–
700462526
SMB24 Button Module
Charcoal Grey
700462518
SMB24 without faceplate
–
700462526
SMB24 Replacement Stand
Silver
700416571
Replacement Stand
Silver
700416563
Wedge Stand
Charcoal Grey
700383888
Wall Mounting Plate
Charcoal Grey
700383383
Gigabit Adapter
–
700383771
Bluetooth Adapter
–
700383789
Replacement Handset
700416548
Amplified Speech Handset
700446370
Replacement Handset Cord (9 feet)
700383318
IP Office Standard Version Installation
IP Office 7.0
Page 319
15-601042 Issue 23e (16 March 2011)
Replacement Handset Cord (25 feet)
700383821
Replacement Line Cord
700383326
IP Office Standard Version Installation
IP Office 7.0
Page 320
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.54 Audio Conferencing Unit
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
The Audio Conferencing Unit (ACU) is a multiple microphone desktop conferencing unit. The Audio Conferencing unit only
supports the following Feature codes:
· Speeddial: Feature 0
This feature code can be used to dial a stored number.
· If Feature 0 is followed by a 3-dight number in the range 000 to 255, the system directory entry with the
matching index is dialed.
· If Feature 0 is followed by * and a 2-digit number in the range 71 to 94, the personal directory entry with the
matching index is dialed.
· Hold/Switch Calls: Feature 2
This feature code will hold the current call. If there was already a call on hold, the feature code will switch between
calls.
· Conference: Feature 3
If the Audio Conferencing Unit has a call connected and another call on hold, using this feature code will conference
the unit and those calls.
· Last Number Redial: Feature 5
When the phone is idle, this feature code can be used to redial the last number dialed from the Audio Conferencing
Unit.
IP Office Standard Version Installation
IP Office 7.0
Page 321
15-601042 Issue 23e (16 March 2011)
9.11.55 ETR 6, ETR 6D
This phone is supported with IP Office Release 6.0 and higher. It is only supported on an ETR6 card in IP500v2 systems.
They are only supported in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version
and IP Office Essential Edition - Quick Version mode systems running in a North American locale. They are not supported
in IP Office Standard mode.
Both 'Refresh' and 'Euro Style' variants of the phones are supported. An additional analog device using the same extension
number can be connected via the ETR phone's AUX socket.
IP Office Standard Version Installation
IP Office 7.0
Page 322
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.56 ETR 18, ETR 18D
This phone is supported with IP Office Release 6.0 and higher. It is only supported on an ETR6 card in IP500v2 systems.
They are only supported in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version
and IP Office Essential Edition - Quick Version mode systems running in a North American locale. They are not supported
in IP Office Standard mode.
Both 'Refresh' and 'Euro Style' variants of the phones are supported. An additional analog device using the same extension
number can be connected via the ETR phone's AUX socket.
IP Office Standard Version Installation
IP Office 7.0
Page 323
15-601042 Issue 23e (16 March 2011)
9.11.57 ETR 34D
This phone is supported with IP Office Release 6.0 and higher. It is only supported on an ETR6 card in IP500v2 systems.
They are only supported in IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version
and IP Office Essential Edition - Quick Version mode systems running in a North American locale. They are not supported
in IP Office Standard mode.
Both 'Refresh' and 'Euro Style' variants of the phones are supported. An additional analog device using the same extension
number can be connected via the ETR phone's AUX socket.
A maximum of 4 ETR 34D phones are supported on a system with a maximum of 2 on any individual ETR6 base card.
IP Office Standard Version Installation
IP Office 7.0
Page 324
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.58 M7100
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
9.11.59 M7100N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 325
15-601042 Issue 23e (16 March 2011)
9.11.60 M7208
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
9.11.61 M7208N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 326
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.62 M7310
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
9.11.63 M7310N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 327
15-601042 Issue 23e (16 March 2011)
9.11.64 M7324
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
· Additional buttons can be supported on a M7324 phone through the addition of KLM button module
344 .
9.11.65 M7324N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 328
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.66 T7000
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
The T7000 telephone is an entry-level digital set for basic low-use office environments. The T7000 is used primarily in the
EMEA (not available in North America).
9.11.67 T7100
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 329
15-601042 Issue 23e (16 March 2011)
9.11.68 T7208
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 330
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.69 T7316
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Standard Version Installation
IP Office 7.0
Page 331
15-601042 Issue 23e (16 March 2011)
9.11.70 T7316E
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
· Additional buttons can be supported on a T7316E phone through the addition of T7316E KEM
IP Office Standard Version Installation
IP Office 7.0
347
button modules.
Page 332
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.71 T7406, T7406e
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
These cordless phones use a base station that can support multiple sets. The T7406E base station supports up to 4
T7406E handsets. The T7406 base station supports up to 3 T7406 handsets. Each supported handset requires a
connection from the base station to a TCM port on the IP Office system.
Each phone is dedicated to its base station and cannot roam even if multiple base stations are installed.
The T7406E is available in North America, Mexico and Caribbean countries excluding Jamaica and Trinidad. The T7406E
replaces the discontinued T7406 cordless telephone.
IP Office Standard Version Installation
IP Office 7.0
Page 333
15-601042 Issue 23e (16 March 2011)
9.11.72 T3 Classic
This phone is supported in Europe only (U-Law only). The T3 Classic has 2 Link ports for optional add-on T3 Headset and
or T3 DSS units (up to 2 further T3 DSS units can be chained from the first T3 DSS).
The IP Office supports T3 UPN and IP phones. It does not support T3 IPN phones. Previous restrictions against using T3
phones on systems with other types of digital stations no longer apply.
T3 Classic
Feature
Detail
Connects via
DS port.
IP Office Release
3.1+.
[Not Small
Office Edition]
Programmable Buttons
4.
Headset Socket*
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Upgradeable Firmware
*Using optional T3 Headset Link unit.
Variant
Colour
SAP Code
T3 UPN Classic
Black
700380272
White
700380306
Black
700414733
White
700414725
Black
700380322
White
700380330
Black
700380348
White
700380355
T3 IP Classic
T3 DSS Unit
T3 DSS Expansion Unit
T3 IP Power Supply Unit
700414766
AEI/Headset Link for T3 IP
700414774
Power Supply for T3 IP DSS
700414790
Headset Link for T3 UPN
700380363
IP Office Standard Version Installation
IP Office 7.0
Page 334
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.11.73 T3 Comfort
This phone is supported in Europe only (U-Law only). The T3 Classic has 2 Link ports for optional add-on T3 Headset and
or T3 DSS units (up to 2 further T3 DSS units can be chained from the first T3 DSS).
The IP Office supports T3 UPN and IP phones. It does not support T3 IPN phones. Previous restrictions against using T3
phones on systems with other types of digital stations no longer apply.
T3 Comfort
Feature
T3 Comfort
Connects via
DS ports.
IP Office Release
3.1+
[Not Small Office
Edition]
Programmable Buttons
10.
Headset Socket*
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Upgradeable Firmware
*Using optional T3 Headset Link unit.
Variant
Colour
SAP Code
T3 UPN Comfort
Black
700380280
White
700380314
Black
700414758
White
700414741
Black
700380322
White
700380330
Black
700380348
White
700380355
T3 IP Comfort
T3 DSS Unit
T3 DSS Expansion Unit
T3 IP Power Supply Unit
700414766
AEI/Headset Link for T3 IP
700414774
Power Supply for T3 IP DSS
700414790
Headset Link for T3 UPN
700380363
IP Office Standard Version Installation
IP Office 7.0
Page 335
15-601042 Issue 23e (16 March 2011)
9.11.74 T3 Compact
This phone is supported in Europe only (U-Law only). The T3 Classic has 1 Link port for optional add-on T3 Headset or T3
DSS units (up to 2 further T3 DSS units can be chained from the first T3 DSS).
The IP Office supports T3 UPN and IP phones. It does not support T3 IPN phones. Previous restrictions against using T3
phones on systems with other types of digital stations no longer apply.
T3 Compact
Feature
T3 Compact
Connects via
DS ports.
IP Office Release
3.1+
[Not Small Office
Edition]
Programmable Buttons
10.
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Upgradeable Firmware
*Using optional T3 Headset Link unit.
Variant
Colour
SAP Code
T3 UPN Compact
Black
700380264
White
700380298
Black
700414717
White
700414709
Black
700380322
White
700380330
Black
700380348
White
700380355
T3 IP Compact
T3 DSS Unit
T3 DSS Expansion Unit
T3 IP Power Supply Unit
700414766
AEI/Headset Link for T3 IP
700414774
Power Supply for T3 IP DSS
700414790
Headset Link for T3 UPN
700380363
IP Office Standard Version Installation
IP Office 7.0
Page 336
15-601042 Issue 23e (16 March 2011)
System Components: Phones
9.12 Phone Add-Ons
For IP Office Release 5.0 and higher, the maximum combined number of buttons on buttons modules per system is 1024.
T3 DSS modules are not included in the combined limits stated above but are limited to 30 T3 DSS modules (1080
buttons).
· 1100 KEM: +18 (Max 3 per phone, 56 per system.)
Add-on for 1120E and 1140E phones. Each module provides 18 additional programmable buttons.
· 1200 KEM: +12 (Max 7 per phone, 85 per system.)
Add-on for 1220 and 1230 phones. Each module provides 12 additional programmable buttons.
· 4450 339 : +60 (Max 2 per phone, 2 per external expansion module or control unit, 8 per system.)
Add-on for 4412D+ and 4424D+ phones. Provides an additional 60 programmable buttons with a single lamp - red
except for the bottom two rows which are green. Due to the single lamp not recommended for appearance
functions as not all button states can be indicated.
· BM12: +24 (Max 3 per phone, 32 per system.)
Add-on for 9408 and 9508 309 phones. Provides 12 buttons assignable in 2 pages for 24 features.
· BM32 340 : +32 (Max 3 per phone, 32 per system.)
Add-on for the 1616 phones that provides two columns of 16 buttons. Up to 3 BM32 modules are supported with
any 1616. For IP Office 5.0, up to a maximum of 32 BM32 modules total are supported the IP Office system.
· DBM32 341 : +32 (Max 3 per phone, 32 per system.)
Add-on for the 1416 phones that provides two columns of 16 buttons. Up to 3 BM32 modules are supported with
any 4616. For IP Office 5.0, up to a maximum of 32 BM32 modules total are supported the IP Office system.
· EU24 342 : +24 (Max 1 per phone, 8 per system.)
Add-on for the 2420, 4620, 4620SW, 4625, 5420, 5620, 5620SW and 5621. Provides an additional 24
programmable buttons. Button display icons are on two switchable pages with 12 icons on each page.
· EU24BL 343 : +24 (Max 1 per phone, 8 per system.)
As per the EU24 above but with a backlight function to match the 4621. Not supported on the 2420 and 5420.
· KLM 344 : +48 (Max 2 per phone, 21 per system.)
Used with M7324 328 phones. Up to 2 buttons modules are supported per phone. Each button module provides 48
programmable buttons.
· SMB12: +24 (Max 3 per phone, 42 per system.)
Supported with 9600 Series phones except 9620 and 9621 variants. SMB12 and SMB24 modules cannot be mixed
on the same phone.
· SMB24 345 : +24 (Max 3 per phone, 42 per system.)
Supported with 9600 Series phones except 9620 and 9621 variants. SMB12 and SMB24 modules cannot be mixed
on the same phone.
· T3 DSS 346 : +36 (Max 3 per phone, 30 per system.)
Up to 3 of these units can be connected to any of the IP Office T3 phones. Each provides an additional 36
programmable buttons. Each button includes a single red status LED. Maximum 3 per phone, 30 per system.
Connection of the T3 DSS varies:
· With non-IP models, the first T3 DSS connects directly to a link port on the phone. No additional power
supplies are required.
· With T3 IP Models, the first T3 DSS connects to a DSS Link Unit fitted to the phone. A power supply is required
for the DSS.
· T7316E KEM 347 : +24 (Max 9 per phone, 42 per system.)
Used with T7316E 332 phones. Each button module provides 24 programmable buttons. Up to 4 buttons modules
are supported per phone without additional power supply. Up to 4 buttons modules are supported per phone
without additional power supply. From 5 to 9 modules can be supported with additional power. Maximum 9 per
phone (4 without additional power).
· XM24 348 : +24 (Max 1 per phone, 2 per expansion module or control unit, 21 per system.)
Add-on for 6416D and 6424D phones. Provides an additional 24 programmable buttons. Connects direct to phone.
IP Office Standard Version Installation
IP Office 7.0
Page 337
15-601042 Issue 23e (16 March 2011)
9.12.1 201B RIM
The 201B Recorder Interface Module (RIM) is supported for use with 2420 and 5420 phones. It provides the phone with a
3.5mm mini-RCA jack socket for connection of recording devices. It also provides two headset sockets which can be used
in place of the phones existing headset socket (the phone and the RIM sockets can not be used at the same time).
· The 201B is the RoHS compliant replacement for the 201A. The 20B stand is the RoHS complaint replacement for the
20A stand.
To install the 201B, the phones existing stand must be removed and be replace by a 20B stand (also called the 20B
Module Adapter Base). This is an expanded stand that includes two slots, into one of which the 201B can be inserted.
However only one 201B is supported per phone.
Use of the 20B and therefore the 201B requires the phone to be powered by a 1151D1 or 1151D2 power supply unit. Full
installation instructions are included with the 20B Stand.
Item
SAP Code
201B Recorder Interface Module
700381635
20B Stand
700381650
EU24
Multi-Grey
700381817
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
IP Office Standard Version Installation
IP Office 7.0
Page 338
15-601042 Issue 23e (16 March 2011)
System Components: Phone Add-Ons
9.12.2 4450
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
The DSS4450 works in association with the 4412D and 4424D telephones, each of which can support up to two DSS4450
adjuncts.
Each DSS4450 provides an additional 60 programmable keys with single red lamps except for the bottom two rows which
have green lamps. The DSS4450 requires an auxiliary Avaya power supply unit and must be used with the cables supplied.
IP Office supports a maximum 2 x 4450 units on each Digital Station expansion module, including the IP406 V2 control
unit. A maximum of 8 x 4450 units total are supported on the whole IP Office system. For additional limitations see Phone
Add-Ons 337 .
This phone is not supported on the IP500 DS8 Extension Card. For the IP500 it will work on external Digital Station
Expansion Modules.
4450
Feature
Detail
Connects via
DSS port on phone.
Supported by
4412D+, 4424D+
Maximum per phone
2.
Maximum per DS module/
control unit
2.
Maximum per IP Office
system
8.
Additional requirements
4450 power supply unit on phone.
IP Office Release
1.0+
Programmable Buttons
60
(50x
Item
SAP Code
4450 (Black)
108199696
4450 (White)
108199407
Small 4400 Series Stand (Black)
108541194
Small 4400 Series Stand (White)
108541202
Power Supply for 4450
108596412
IP Office Standard Version Installation
IP Office 7.0
/10x
).
Page 339
15-601042 Issue 23e (16 March 2011)
9.12.3 BM32
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
The BM32 add on provides an additional 32 twin-LED programmable buttons for 1616 phones. The units do not require
their own power supply connection as they draw power from the phone to which they are connected.
· Up to 3 units can be connected in a chain from a single 1616.
· For 1616 phones, to support a BM32 the phone must be powered by an individual 1600 Series Power Adapter.
· Up to a maximum of 32 BM32 units on the system. For additional limitations see Phone Add-Ons
337 .
Item
SAP Code
BM32 BUTTON MODULE
700415573
Accessories
1600 SERIES BM32 CABLE - REPLACEMENT
700415581
1600 SERIES BM32 BOND BRIDGE - REPLACEMENT
700415599
1616/BM32 PLASTIC LABEL COVERS (20) – REPLACEMENT
700415672
1600 SERIES BM32 FLIP STAND - REPLACEMENT
700432800
Paper Labels
1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (8.5" x 11")
700415656
1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (A4)
700434236
IP Office Standard Version Installation
IP Office 7.0
Page 340
15-601042 Issue 23e (16 March 2011)
System Components: Phone Add-Ons
9.12.4 DBM32
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
The DBM32 add on provides an additional 32 twin-LED programmable buttons for 1416 phones. The units do not require
their own power supply connection as they draw power from the phone to which they are connected.
· Up to 3 units can be connected in a chain from a single 1416.
· Up to a maximum of 32 DBM32 units on the system.
Item
SAP Code
DBM32 BUTTON MODULE
700469968
Accessories
1600 SERIES BM32 CABLE - REPLACEMENT
700415581
1600 SERIES BM32 BOND BRIDGE - REPLACEMENT
700415599
1616/BM32 PLASTIC LABEL COVERS (20) – REPLACEMENT
700415672
1600 SERIES BM32 FLIP STAND - REPLACEMENT
700432800
Paper Labels
·
1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (8.5" x 11")
700415656
1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (A4)
700434236
Note for Australian installations only:
Installations of the 1416 terminal with an 1151 PSU and DBM32 must be restricted to the same building as the host
Gateway. That is, the 1416 – if installed with an 1151 PSU and DBM32 – cannot be connected in a campus
environment where the 1416 terminal is installed in a building separate from the building housing the Gateway.
This application cannot be used with exposed (out-of-building) wiring.
· For installations in which the 1416 is used without the 1151 PSU and DBM32, campus connections are
acceptable: the 1416 can be located in a separate building in these cases.
· This restriction applies to Australian installations only.
IP Office Standard Version Installation
IP Office 7.0
Page 341
15-601042 Issue 23e (16 March 2011)
9.12.5 EU24
The maximum number of button module buttons supported, of any type, on a single system is 1024
Provides an additional 24 programmable buttons. For additional limitations see Phone Add-Ons
·
337 .
337 .
Only the cable supplied with the EU24/EU24BL should for connection to the EU24/EU24BL. This cable should
only be connected to the port marked EU24 on suitable phones. Doing otherwise will cause damage to the EU24/
EU24BL and the equipment to which it is attached.
EU24
Feature
Detail
Connects via
EU24 port on phone.
Supported by
2420, 4620, 4621, 4625, 5420, 5620, 5621.
Maximum per phone
1.
Maximum per IP Office
8.
Additional Requirements
A 1151 Type power supply unit must be used to
power the phone.
IP Office Release
3.0+
Programmable Buttons
24.
Item
SAP Code
EU24 1XU-A Expansion Module
Multi-Grey
700381817
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
IP Office Standard Version Installation
IP Office 7.0
Page 342
15-601042 Issue 23e (16 March 2011)
System Components: Phone Add-Ons
9.12.6 EU24BL
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
Provides an additional 24 programmable buttons. The EU24BL is physically similar to the EU24 but includes a backlight
function that matches 4621 phone. For additional limitations see Phone Add-Ons 337 .
·
Only the cable supplied with the EU24/EU24BL should for connection to the EU24/EU24BL. This cable should
only be connected to the port marked EU24 on suitable phones. Doing otherwise will cause damage to the EU24/
EU24BL and the equipment to which it is attached.
EU24BL
Feature
Detail
Connects via
EU24 port on phone.
Supported by
4620, 4621, 4625, 5620, 5621.
Maximum per phone
1.
Maximum per IP Office
8.
Additional requirements
A 1151 Type power supply unit must be used
to power the phone.
IP Office release
3.1+.
Programmable Buttons
24.
Item
SAP Code
EU24BL 2XU-A Backlighted Expansion Module
Multi-Grey
700381544
1151D1 Power Supply
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia/New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
IP Office Standard Version Installation
IP Office 7.0
Page 343
15-601042 Issue 23e (16 March 2011)
9.12.7 KLM Module
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
This type of button module can be used with the M7324 328 phones to provide additional programmable buttons. For <%
STANARD%>, up to 2 modules can be attached to each phone. For IP Office Essential Edition - PARTNER® Version,IP
Office Essential Edition - Norstar Version and IP Office Essential Edition - Quick Version only 1 module can be attached to
each phone. Each module requires its own power supply unit.
+01
+13
+25
+37
+02
+14
+26
+38
+03
+15
+27
+39
+04
+16
+28
+40
+05
+17
+29
+41
+06
+18
+30
+42
+07
+19
+31
+43
+08
+20
+32
+44
+09
+21
+33
+45
+10
+22
+34
+46
+11
+23
+35
+47
+12
+24
+36
+48
IP Office Standard Version Installation
IP Office 7.0
Page 344
15-601042 Issue 23e (16 March 2011)
System Components: Phone Add-Ons
9.12.8 SMB24
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
This button module is supported with most 9600 Series phones except for 9620 and 9621 phones. Up to 3 SMB24 modules
can be attached to any one phone. For additional limitations see Phone Add-Ons 337 .
Note that SMB12 and SMB24 may not be mixed on the same phone.
· The Class requirement of PoE powered phones may be increased if the phone is used with additional equipment
such as a button module.
Variant
SAP Code
SMB24 Button Module
Charcoal Grey
700462518
SMB24 without faceplate
–
700462526
SMB24 Replacement Stand
Silver
700416571
IP Office Standard Version Installation
IP Office 7.0
Page 345
15-601042 Issue 23e (16 March 2011)
9.12.9 T3 DSS
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
The T3 DSS provides an additional 36 programmable keys for phones in the supported T3 series. The T3 DSS is moulded
and designed to be attached to the associated phone. Signalling is achieved by cable connection to the Link port on the T3
phone. A further two T3 DSS units can be chained from the first T3 DSS. For additional limitations see Phone Add-Ons 337
.
Feature
Detail
Connects via
Link port on phone.
Supported by
T3 Compact, T3 Classic, T3 Comfort
Maximum per phone
3.
Maximum per DS module
-.
Additional requirements
None.
IP Office release
3.1+.
Programmable Buttons
36.
Item
Colour
SAP Code
T3 DSS Unit
Black
700380322
White
700380330
Black
700380348
White
700380355
T3 DSS Expansion Unit
IP Office Standard Version Installation
IP Office 7.0
Page 346
15-601042 Issue 23e (16 March 2011)
System Components: Phone Add-Ons
9.12.10 T7316e KEM
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
This type of button module can be used with the T7316E 332 phones to provide 24 additional programmable buttons. For
IP Office Standard Version, up to 9 modules can be added per phone, though addition power requirements apply if more
than 4 modules are used with a phone. For IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition Norstar Version and IP Office Essential Edition - Quick Version, only 4 modules can be added per phone.
IP Office Standard Version Installation
IP Office 7.0
+01
+13
+02
+14
+03
+15
+04
+16
+05
+17
+06
+18
+07
+19
+08
+20
+09
+21
+10
+22
+11
+23
+12
+24
Page 347
15-601042 Issue 23e (16 March 2011)
9.12.11 XM24
The maximum number of button module buttons supported, of any type, on a single system is 1024
337 .
Connects to the XM24 port on the base of 6416 and 6424 phones. Requires the phone to have a separate power supply
using an Avaya 1151D1 or 1151D2 power supply unit and a power outlet socket are required. For additional limitations
see Phone Add-Ons 337 .
XM24
Feature
XM24
Connects via
XM24 port on phone.
Supported by
6416+, 6424+
Maximum per phone
1.
Maximum per DS module/control unit
2.
Maximum per IP Office system
10
Additional requirements
1151D1 or 1151D2 PSU for phone.
IP Office Release
1.0+.
Programmable Buttons
24.
Item
XM24
SAP Code
Grey
700406523
White
700406515
Grey
108272378
White
108272386
1151D1 Power Supply.
With CAT5 cable.
700434897
1151D2 Power Supply with battery backup.
With CAT5 cable.
700434905
1151D1/1151D2 Power Cord
USA
405362641
Europe
407786623
Australia and New Zealand
407786631
India
407790991
United Kingdom
407786599
Argentina
408161453
XM24 Stand
IP Office Standard Version Installation
IP Office 7.0
Page 348
15-601042 Issue 23e (16 March 2011)
System Components: Phone Add-Ons
9.13 Ancilliary Systems
9.13.1 Digitial Mobility Solution
Avaya 4100 Series and 7400 Series phones are supported using a Digital Mobility Solution (DMS). This is a DECT system
that can be used to support up to 64 handsets. The DMS connects to the IP500 system using a TCM port for each
handset.
Digital Mobility 2.4 GHz solution - North America and CALA
7420 Handset
N7B80BK
7430 Handset
N7B80BLE6
7440 Handset
N7B80BQE6
Digital Mobility Base Station 10
2.4GHz, Compatible with Handset 7430/7440, Repeater 40.
N7B65KPE5
Digital Mobility Repeater 40
2.4GHz, Compatible with Handset 7430/7440, Base station 10. N7B80AGE5
Digital Mobility External Antenna 51
International.
N7B65KWE5
DMC 080 Digital Mobility Controller
North America.
N7B65KJE5
DMC 320 Digital Mobility Controller
North America.
N7B65KKE5
Digital Mobility 1.9 GHz solution - North America
7439 Handset
Replaces the 7430 model.
N7B80CLE6
7449 Handset
Replaces the 7430 model.
N7B80CNE6
Digital Mobility Base Station 19
North America.
N7B80CRE6
Digital Mobility Repeater 49
Canada, US.
N7B80CUE6
Digital Mobility External Antenna 51
International.
N7B65KWE5
DMC 080 Digital Mobility Controller
North America.
N7B65KJE5
DMC 320 Digital Mobility Controller
North America.
N7B65KKE5
Digital Mobility 1.8 GHz solution - Europe, Hong Kong, Australia, New Zealand
4135 Handset
Europe & Hong Kong
N7B80BME6
4145 Handset
Europe & Hong Kong
N7B80BRE6
4145EX Handset KIT - EU
Ruggedized version of 4145 - Europe & Hong Kong
N7B80BWE6
4136 Handset
Australia/New Zealand
N7B80CCE6
4146 Handset
Australia/New Zealand
N7B80CEE6
4146EX Handset
Ruggedized version of 4146 - Australia/New Zealand
N7B80CFE6
Digital Mobility Base Station 15
N7B65KTE5
Digital Mobility Repeater 25
N7B65KUE5
Digital Mobility Repeater 45
N7B80AHE5
Digital Mobility External Antenna 51
International
N7B65KWE5
DMC 081 Digital Mobility Controller
International
N7B80AAE5
DMC 321 Digital Mobility Controller
International
N7B80ABE5
Digital Mobility 1.8 GHz solution - South America
7434 (South America)
N7B80ACE6
7444 (South America)
N7B80ADE6
Digital Mobility Base Station 14
N7B80AEE6
Digital Mobility Repeater 24
N7B80AFE6
Digital Mobility External Antenna 51
International
N7B65KWE5
DMC 081 Digital Mobility Controller
International
N7B80AAE5
DMC 321 Digital Mobility Controller
International
N7B80ABE5
IP Office Standard Version Installation
IP Office 7.0
Page 349
15-601042 Issue 23e (16 March 2011)
9.13.2 DECT R4
Avaya 3720, 3725, 3740 and 3749 phones connect to the DECT base stations in a DECT R4 system. They then connect to
the IP Office via the IP network.
Avaya 3701 and 3711 phones are also supported but only as GAP compatible devices.
IP Office Standard Version Installation
IP Office 7.0
Page 350
15-601042 Issue 23e (16 March 2011)
System Components: Ancilliary Systems
9.14 Applications
This section outlines the requirements for various IP Office applications. These are just outlines, for full details refer to the
specific installation manuals for those applications and to the IP Office Technical Bulletins.
9.14.1 IP Office Application Server
The IP Office Application Server is a single server installation package for the IP Office applications listed below. The DVD
installs the CentOS Linux operating system, the IP Office applications and a set of web pages for server management.
Note that except in the case of an IP Office Application Server upgrade, the installation overwriites any existing oeprating
system and data on the server PC.
· one-X Portal for IP Office 357
User and configuration access is via web browser in the same way as for a Windows sever installation of one-X
Portal for IP Office.
· Voicemail Pro 363
Configuration access is done using a Windows installation of the Voicemail Pro client software. An installation
package for the Voicemail Pro client is included on the IP Office Application Server server.
For Voicemail Pro server running on the IP Office Application Server, the following Voicemail Pro features are not
supported:
· VB Scripting.
· UMS Web Voicemail
However access via IMAP and one-X Portal are available as alternatives.
· TTS Text to Speech.
· 3rd Party Database Integration.
· MAPI Email.
· VPNM.
· UMS Exchange Integration.
When logged into the voicemail server using the Voicemail Pro client, those features not supported are grayed out or
hidden. If those features are present in an imported call flow, they will not function and calls attempting to use those
features will be disconnected.
The Voicemail Pro client's backup and restore functions can be used to move voicemail data between a Linux based server
and a Windows based server and vice versa.
For Small Community Network scenarios where multiple voicemail servers are present, for example distributed and backup
server, a mix of Linux based and Windows based servers are allowed.
Details
DVD
IP Office Application Server Release 7.0 DVD Set (2) - 700501420
License
- Depends on the IP Office applications selected during installation. The IP Office Application
Server server itself does not require any license.
PC Requirements
The compatibility of any particular server PC cannot be guaranteed. A list of known suitable servers is available at https://
hardware.redhat.com/.
PC Requirements
Minimum
Recommended
RAM
2GB
4GB
Hard Disk Free Space
30GB
30GB
Core 2 duo
Quad Core 2.4GHz
Processor:
- Pentium
- AMD
Athlon 64 4000
Additional Apps:
- Web Browser
·
·
·
·
Internet Explorer 7+.
Firefox 3+
Opera 2+
Safari 3.2+
Ports
Component
Ports
IP Office Application Server
· HTTP/HTTPS Access
· SFTP Access
7070
22
IP Office Standard Version Installation
IP Office 7.0
Page 351
15-601042 Issue 23e (16 March 2011)
· Access to additional ports is as per the IP Office applications selected during installation.
IP Office Standard Version Installation
IP Office 7.0
Page 352
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.14.2 ContactStore
The Voicemail Pro can be used for manual and automatic call recording. Normally those recordings are placed into the
mailbox specified for the user or hunt group whose call is being recorded and are then treated as normal messages.
Contact Store allows those recordings to be redirected into a database on the ContactStore PC. This allows recordings to
be archived and searched separately from user messages. User access to Contact Store is via web browser. This
application requires entry of a license into the IP Office configuration.
· For IP Office Release 6 and higher, the supported version of ContactStore for IP Office is 7.8.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 2)
License
VMPro Recordings Administrators (IP400 ContactStore for IPO RFA - 187166).
See Voicemail Pro Licenses 392 .
PC Requirements
Minimum Server PC Requirements
Operating System Support
RAM
512MB
Server OS:
Hard Disk Free Space
10GB*
2003 Server
Processor:
2008 Server
- Pentium
P4 2.4GHz
Client OS:
- Celeron
Not tested.
XP Professional
- AMD
Athlon XP 3000+, Athlon64
Vista
Additional Apps:
- Web Browser
Windows 7
· Internet Explorer 7.
· Internet Explorer 8.
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
· If run on the same PC as the Voicemail Pro, apart from meeting the requirements of Voicemail Pro:
· ContactStore must use a separate disk partition from Voicemail Pro.
· Minimum hard disk free space increases to 20GB* and Pentium processor to P4 2.8GHz minimum.
· *1: For all voicemail servers, also allow 1MB per minute for messages and greeting storage.
· *2: Also allow 7.2MB per hour for recordings in the Contact Store disk partition.
· Recordings and data are stored in PostgresSQL database. This is created during installation of the Contact Store
software.
· ContactStore is not supported on 32-bit operating systems.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
Contact Store
Witness\tomcat5024\bin\tomcat5.exe
TCP 8888.
UDP 50791.
UDP 50795.
IP Office Standard Version Installation
IP Office 7.0
Page 353
15-601042 Issue 23e (16 March 2011)
9.14.3 Customer Call Reporter (CCR)
· Customer Call Reporter 354
This application is installed on a server PC connected to the IP Office. Users access the application from their PC
using a web browser. The application obtains data about the calls handled by CCR agents and groups from the IP
Office system and stores that data in an MS-SQL database. It can support up to 150 agents and 75 supervisors.
Details
DVD
License
Languages
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 2)
See Customer Call Reporter Licenses
394 .
Dutch, English (UK), English (US), French, Italian, Brazilian Portuguese, Russian and Spanish.
PC Requirements
Minimum Server PC Requirements
Operating System Support
RAM
2GB
Server OS:
Hard Disk Free Space
30GB
2003 Server
Processor:
2008 Server
- Pentium
Intel Pentium D945 Dual Core
Client OS:
- Celeron
Not tested.
XP Professional
- AMD
AMD Athlon 64 4000+.
Vista
User PC Requirements
Web Browser
Windows 7
·
·
·
·
·
Google Chrome
Internet Explorer 7.
Internet Explorer 8.
Mozilla Firefox 3.0.
Safari 3.2.
IP Office Standard Version Installation
IP Office 7.0
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
Page 354
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.14.4 Manager
This tool is used to access all parts of the IP Office configuration. Different levels of access can be defined to control which
parts of the configuration the Manager user can view and alter. Manager is also used to upgrade the software files used by
an IP Office system. When running is also acts as a TFTP server from which some Avaya phones can request new
software.
Note that IP Office Manager's software level is always two higher than the IP Office core software with which it is release.
For example IP Office 6.0 core software is release with IP Office Manager 8.0.
IP Office Manager is backwards compatible and can be used to manage IP Office systems running software from IP Office
2.1 upwards.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Languages
English, Brazilian, Dutch, French, German, Italian, Spanish (Mexican).
License
No license required.
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
256MB
Server OS:
Hard Disk Free Space
1GB*
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon Opteron, Athlon64/XP
Vista
Additional Apps:
- .NET2
Windows 7
Installed with Manager if not
already present.
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
*Includes disk space required for .NET2 component.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
IP Office Manager
Manager\manager.exe
TCP Port 50802.
TCP Port 50804.
TCP Port 50812.
UDP Port 50798.
IP Office Standard Version Installation
IP Office 7.0
Page 355
15-601042 Issue 23e (16 March 2011)
9.14.5 Monitor
Monitor (also known as System Monitor) is a tool that can show all activity on the IP Office system in great detail. As a
consequence, interpretation of Monitor traces requires a high-level of data and telephony protocol knowledge. However, all
IP Office installers and maintainers must understand how to run Monitor when necessary as Avaya may request copies of
Monitor traces to resolve support issues.
For IP Office 4.0 and higher, the System Status Application
information than is provided by Monitor.
361
has been added to provide more easily interpreted
· Two versions of Monitor are included in the IP Office Admin applications suite, one for IP Office 4.0 systems and
one for pre-4.0 IP Office systems. Care should be taken to ensure that the correct version is used when monitoring
an IP Office system.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Languages
English only.
License
No license required.
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
128MB
Server OS:
Hard Disk Free Space
10GB
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon B 650MHz
Vista
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
· Vista support is only on Business, Enterprise and Ultimate versions.
· Windows 7 support is only on Professional, Enterprise and Ultimate versions.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
System Monitor
Monitor\sysmonitor.exe
UDP 50794.
IP Office Standard Version Installation
IP Office 7.0
Page 356
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.14.6 one-X Portal for IP Office
This application is installed on a server PC connected to the IP Office. Users can access the one-X portal from their own PC
using a web browser. The application allows the user to control their phones, access voicemail messages, call logs and
phone directories.
Details
DVD
License
Languages
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 2) or IP Office Application
Server Release 7.0 DVD Set (2) - 700501420
See User Licenses
390 .
Dutch, English (UK), English (US), French, Italian, Brazilian Portuguese, Russian and Latin
Spanish.
The details below are for a Windows based server installation of one-X Portal for IP Office. one-X Portal for IP Office can
also be installed as part of a Linux based server installation using the IP Office Application Server DVD 351 .
PC Requirements
Minimum Server PC Requirements
Operating System Support
RAM
2GB
Server OS:
Hard Disk Free Space
10GB
2003 Server
Processor:
2008 Server
- Pentium
Intel Pentium D945 Dual Core
Client OS:
- Celeron
Not tested.
XP Professional
N/A
- AMD
AMD Athlon 64 4000+.
Vista
N/A
Windows 7
N/A
User PC Requirements
Web Browser
·
·
·
·
·
Google Chrome
Internet Explorer 7.
Internet Explorer 8.
Mozilla Firefox 3.0.
Safari 3.2.
IP Office Standard Version Installation
IP Office 7.0
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
Page 357
15-601042 Issue 23e (16 March 2011)
9.14.7 Phone Manager
Phone Manager is an application that allows the user to control and monitor their own phone through their PC. For Avaya
phones that support handsfree operation, Phone Manager can be used to make and answer calls. During usage, the Phone
Manager records details of calls made, answered and missed. It can also be configured to show the status of other users
on the system. Phone Manager also allows the user to access and change many of the setting stored in the IP Office
configuration that relate to their own phone operation, for example their forwarding destination numbers.
Though installed as a single set of software, that same software can operate in several modes:
· Phone Manager Lite
The default mode of Phone Manager. Requires no license, this application can be installed for any IP Office user.
· Phone Manager Pro
Users configured for Professional Edition mode are able to access a range of additional features. Phone manager Pro
requires entry of licenses into the IP Office system. The licenses also control the number of simultaneous Phone
Manager Pro users. The user's Phone Manager software then automatically changes from Lite mode to Professional
Edition mode.
· Phone Manager Pro PC Softphone (formerly called Phone Manager iPro)
This is a PC softphone mode of Phone Manager operation. The user acts as a VoIP extension, making calls through
the speaker and microphone of their PC. This mode requires further licenses in addition to the Phone Manager Pro
licenses.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Languages
Brazilian, Chinese (Simplified), Danish, Dutch, English, French, Finnish, German, Italian,
Korean, Latin Spanish, Norwegian, Portuguese, Russian, Spanish, Swedish.
License
Licensed application. See Phone Manager Licenses
397 .
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
64MB
Server OS:
Hard Disk Free Space
160MB for Lite/1GB for Pro.
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional (32-bit)
- AMD
Athlon B 650MHz
Vista (32-bit)
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
· Phone Manager Pro PC Softphone also requires the user PC to have a speaker and microphone installed and the
user associated with an IP extension on the IP Office.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
Phone Manager
Phone Manager\PhoneManager.exe
UDP 50796.
UDP 50799.
Phone Manager VOIP Server
Phone Manager\iClaritySvr.exe
UDP 1719.
UDP 1720.
IP Office Standard Version Installation
IP Office 7.0
Page 358
15-601042 Issue 23e (16 March 2011)
System Components: Applications
Licenses
License shows the name as it appears in the IP Office configuration. RFA Name is the name used for the orderable item.
License
Description
Phone Manager Pro (per seat)
Enables Phone Manager Pro for 1, 5, IP400 Phone Manager 1
10, 20, 50, 100 or unlimited users. Pro
5
The user's Phone Manager mode is
10
set through the IP Office
configuration (User | Telephony |
20
Phone Manager Type).
50
177468
Enables Phone Manager Pro IP
IP400 IPPRO
softphone operation for a user.
Note: Also requires the user to have
a Phone Manager Pro license.
1
171992
5
174463
10
174464
20
174465
50
174466
Phone Manager Pro IP Audio
Enabled (per user)
RFA Name
SAP
177469
177470
177471
177472
· In addition to entering Phone Manager licenses, each user is individually configured for the expected Phone
Manager type.
· During operation, the number of Phone Manager license keys available and the number unused can be checked.
Run Phone Manager and select Help | About. Holding down the Ctrl and Shift keys, click on the software version
number.
IP Office Standard Version Installation
IP Office 7.0
Page 359
15-601042 Issue 23e (16 March 2011)
9.14.8 SoftConsole
This is a licensed application. It is intended for telephone system operators or receptionists. Its displays details of calls
directed to the user and allows them to quickly see the status of the callers required destination and transfer the call. The
SoftConsole user is able to access a range of details about the status of users and groups on the IP Office system.
· The IP Office SoftConsole works in conjunction with a physical IP Office extension phone to provide the speech path
for calls. It is not supported for use with an IP softphone.
· Up to 4 simultaneous SoftConsole users can be licensed.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Languages
Brazilian, Chinese (Simplified), Danish, Dutch, English, French, Finnish, German, Italian,
Korean, Latin Spanish, Norwegian, Portuguese, Russian, Spanish, Swedish.
License
Licensed application. See below.
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
128MB
Server OS:
Hard Disk Free Space
1GB
2003 Server
Processor:
369
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon B 650MHz
Vista
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
SoftConsole
SoftConsole\SoftConsole.exe
UDP 50799.
UDP 50796.
Licenses
License
Description
RFA Name
Receptionist
Adds one additional SoftConsole user. A maximum of four
SoftConsole user can be licensed.
IPO LIC RECEPTIONIST 171987
RFA
IP Office Standard Version Installation
IP Office 7.0
SAP
Page 360
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.14.9 System Status Application (SSA)
This tool provides a wide range of information about the current status of an IP Office 4.0 or higher system. Its includes
available resources and components within the system. This includes details of current call in progress. Details of the
number of alarms are recorded and the time date of the most recent alarms.
When required for diagnostics escalation SSA is able to take a snap shot image of the IP Office system's status including a
copy of its current configuration. Use of SSA requires an IP Office service user name and password that has been
configured for System Status access in the IP Office's security settings.
· For IP500v2 systems, SSA is pre-installed on the system's Avaya SD memory card and can be run by browsing to
the IP Office system's IP address.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
License
No license required.
PC Requirements
Minimum PC Requirements
RAM
256MB
Hard Disk Free Space
1.4GB
Operating System Support
Operating System Support
369
Server OS:
2003 Server
Processor:
- Pentium
PIII 800MHz
- Celeron
Celeron 3 800Mhz
- AMD
Athlon B 650MHz
2008 Server
Client OS:
XP Professional
Vista
Additional Apps:
- Sun Java Virtual
Machine
Installed with SSA if not already
present.
- Web Browser
· Internet Explorer 7+.
· Mozilla Firefox 3.0.
IP Office Standard Version Installation
IP Office 7.0
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
Page 361
15-601042 Issue 23e (16 March 2011)
9.14.10 TAPI
IP Office TAPI is a client PC application that allows TAPI compliant applications to interact with the IP Office. The IP Office
TAPI software can be used in one of two modes, depended on whether it is licensed or not. The same software is installed
in either case with the licenses, if any, being entered in the IP Office system configuration.
· 1st Party TAPI
In this unlicensed mode the TAPI software supports control of an individual user's associated extension, allowing a
TAPI compliant application to answer (requires a phone that supports handsfree answer) and make calls.
· 3rd Party TAPI
In this licensed mode, TAPI software can be used to control call function on multiple user extension. This mode is
used with CTI Developer applications.
Details
DVD
License
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Optional. Licenses are required for 3rd party TAPI mode operation. See CTI Licenses
397 .
PC Requirements: 1st Party TAPI
Minimum PC Requirements
RAM
64MB
Hard Disk Free Space
50MB
Operating System Support
Operating System Support
369
Server OS:
2003 Server
Processor:
- Pentium
PIII 800MHz
- Celeron
Celeron 3 800Mhz
- AMD
Athlon B 65-0MHz
2008 Server
Client OS:
XP Professional
Vista
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
PC Requirements: 3rd Party TAPI
Minimum PC Requirements
RAM
64MB
Hard Disk Free Space
50MB
Operating System Support
Operating System Support
369
Server OS:
2003 Server
Processor:
- Pentium
PIII 800MHz
- Celeron
Celeron 3 800Mhz
- AMD
Athlon B 65-0MHz
2008 Server
Client OS:
XP Professional
Vista
Windows 7
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
TAPI2
TAPI\tspi2w.tsp
UDP 50797.
IP Office Standard Version Installation
IP Office 7.0
Page 362
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.14.11 Voicemail Pro
This application requires various licenses entered into the IP Office configuration to control the features it offers and the
number of simultaneous connections (IP500 = 40 (IP Office 5.0+) or 30 (pre-IP Office 5.0), IP500v2 = 40). The operation
of Voicemail Pro can be customized to provide special services. .
The Voicemail Pro software can be installed as separate Voicemail Pro client and server parts. This allows the remote
administration of the Voicemail Pro server from a PC with just the Voicemail Pro client installed. A copy of the client is
automatically installed locally with the Voicemail Pro server.
Source
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1) or IP Office Application
Server Release 7.0 DVD Set (2) - 700501420
Languages
Chinese (Mandarin and Cantonese), Danish, German, Greek, English (UK), English (US),
Spanish, Latin Spanish, Finnish, French, French Canadian, Hungarian, Italian, Korean, Dutch,
Norwegian, Polish, Portuguese, Brazilian, Swedish.
License
See Voicemail Pro Licenses
392 .
The details below are for a Windows based server installation of Voicemail Pro. Voicemail Pro can also be installed as part
of a Linux based server installation using the IP Office Application Server DVD 351 .
The Voicemail Pro server part of the software consists of several components in addition to the core server software, these
are:
· Campaigns
The Voicemail Pro can be configured to run a campaign. This consists of a series of questions for which the
Voicemail Pro records the callers answer or key presses. The resulting recordings can then be played back by users.
The web aspect of campaigns allows user to perform this playback and processing of campaign recordings via their
web browser. This requires an IIS web server to be run on the same PC as the Voicemail Pro software.
· Text to Speech (TTS)
Through adding additional licenses, the Voicemail Pro is able to use the TTS functions of Windows to speak text and
numbers to callers in addition to recording prompts. This is intended mainly for scenarios where the Voicemail Pro is
obtaining text and number values from a customer database.
· Unified Messaging Service (UMS)
Voicemail Pro supports a feature called voicemail email to send messages or message alerts to a user's email
mailbox. This however is a one-way process with no link back to the user's voicemail mailbox on whether the email
has been read or deleted. UMS allows this to become a two-way process, where users can play voicemail messages
through their email mailbox or voicemail mailbox.
Basic Voicemail Pro
Minimum PC Requirements
Operating System Support
RAM
256MB
Server OS:
Hard Disk Free Space
2GB*
2003 Server
Processor:
Service
Client
2008 Server
- Pentium
P4 1.4GHz
Client OS:
- Celeron
Any 1.7GHz
XP Professional
- AMD
Any 1.4GHz.
Vista
*Also allow 1MB per minute for message and
prompt storage.
Windows 7
· Vista support is only on Business, Enterprise and
Ultimate versions.
· Windows 7 support is only on Professional, Enterprise
and Ultimate versions.
Voicemail Pro plus UMS Web Voicemail and/or Campaigns
Minimum PC Requirements
Operating System Support
RAM
512MB
Server OS:
Hard Disk Free Space
2GB*
2003 Server
Processor:
Service
Client
2008 Server
- Pentium
P4 2.8GHz
Client OS:
- Celeron
Not tested.
XP Professional
IP Office Standard Version Installation
IP Office 7.0
Page 363
15-601042 Issue 23e (16 March 2011)
- AMD
Athlon XP 3000+,
Athlon 64
Vista
Windows 7
*Also allow 1MB per minute for message and
prompt storage.
· Both Web Campaigns and UMS Web Voicemail require the IIS web server on the voicemail server PC to be
enabled.
· UMS Web Voicemail will install PHP if not detected as already installed.
Voicemail Pro plus IVR and or TTS
Minimum PC Requirements: Basic
Voicemail Pro
Operating System Support
Server OS:
RAM
512MB
Hard Disk Free Space
20GB*
Processor:
Service
Client
2003 Server
2008 Server
Client OS:
- Pentium
P4 2.8GHz
- Celeron
Not tested.
- AMD
Athlon XP 3000+,
Athlon 64
XP Professional
Vista
Windows 7
Also allow 1MB per minute for message and prompt
storage.
*Generic TTS only. The current ScanSoft TTS
provided with Voicemail Pro is not supported on
Vista.
· If the database being queried is located on the VM Pro server, the query speed of the database will be affected by
the amount of memory available. Please take into account the memory requirements of the database being queried.
Ports
The Voicemail Pro service uses the following ports.
Port Number
Type
Description
25
TCP
Used to listen for SMTP connections.
37
UDP
Used to receive time requests (RFC 868).
143
TCP
Used to service IMAP4 requests.
50791
UDP
Used to receive requests from IP Office PBX.
TCP
Used to receive requests fromone-X Portal for IP Office.
TCP
Used to receive connections from Voicemail Pro client.
50791
Note that additional ports may be used for connection to services such as 3rd party database or Microsoft Exchange.
IP Office Standard Version Installation
IP Office 7.0
Page 364
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.14.12 Single Server Support
The following scenarios are supported for combining IP Office server applications onto a single server PC.
In all cases, the individual requirements of each application as if installed on a separate server are still applicable. Also,
depending on the application combination, additional restrictions and requirements may be applied as detailed below.
Voicemail Pro
Customer Call
Reporter
one-X Portal for IP
Office
Minimum IP
Minimum PC
Office Release Specification
1.
16 Ports
150 Agents
–
Release 5.0
As per each
application.
2.
8 Ports
(4 TTS)
–
50 Simultaneous
users.
Release 6.0
2GHz Dual Core, 4GB
RAM, Windows 2008
Server (32 or 64-bit).
3.
8 Ports
(4 TTS)
30 Agents
50 Simultaneous
users.
Release 6.0
2GHz Quad Core, 6GB
RAM, Windows 2008
64-bit.
4.
16 ports
(8 TTS)
50 Agents
150 Simultaneous
users.
Release 6.0
CCR run in Windows
2003 on a virtual
server.
· Voicemail Pro includes UMS, VB Scripting and 3rd party database operation. It also includes the installation of
ContactStore if required.
· Both ContactStore and one-X Portal for IP Office use Tomcat servers as part of the application. For scenarios with
both installed, the redirect port setting of the ContactStore's Tomcat server should be configured to a port other
than 8080.
· The supported virtual servers are:
· VMWare Server.
· Microsoft Virtual Server 2005 R2.
· Microsoft Server Hyper-V.
· When used in a virtual server configuration, Customer Call Reporter and one-X Portal each require a 2GB RAM
virtual machine. Voicemail Pro and ContactStore each require a 1GB RAM virtual machine.
IP Office Standard Version Installation
IP Office 7.0
Page 365
15-601042 Issue 23e (16 March 2011)
9.14.13 IP Office Ports
Most PC firewalls will request the user to allow various exceptions when a newly installed application is first run. However
this may not always be the case, especially if the firewall is located elsewhere than the user's PC.
Adding Firewall Exceptions
The file avayafw.bat can be used to open up the necessary firewall exceptions for IP Office applications. The file can be
downloaded from http://marketingtools.avaya.com/knowledgebase/tools/firewall.
It only works for:
· The default Windows XP/Windows 2003 firewall.
· The application must be installed for the exception to be created.
· The application must be installed in the default location.
Whilst avayafw.bat only works subject to the conditions above, for other firewalls study of this file will indicate the
necessary application files and ports for which exceptions need to be created.
Ports Used
The list below details many of the IP ports used by IP Office control units and IP Office applications. Many of these are
standard ports for different IP traffic protocols.
Indicates a listening port on the IP Office control unit.
PC running an IP Office application.
indicates a port to which the IP Office sends, for example to a
* Indicates that the port and or protocol can be changed.
Port
Protocol
25*
SMTP
TCP
Email system alarms from the IP Office to SMTP server. For IP Office 4.2 also used
for Voicemail Email on Embedded Voicemail.
37
Time
UDP
Time requests from the IP Office to a Time Server (RFC868).
53
DNS
UDP
Domain Name Service responses.
67
BOOTP/DHCP
UDP
DHCP server operation.
68
BOOTP/DHCP
UDP
DHCP client operation.
69
TFTP
UDP
File requests to the IP Office.
69
TFTP
UDP
File requests by the IP Office.
80
HTTP
TCP
HTTP File requests.
161*
SNMP
UDP
From SNMP applications.
162*
SNMP Trap
UDP
To addresses set in the IP Office configuration.
500
IKE
UDP
Key exchange for IPSec protocol.
389*
LDAP
TCP
Lightweight Directory Access Protocol.
443
HTTPS
TCP
HTTPS communication with IP Office provisioned DECT, IP Office Softphone.
520
RIP
UDP
520
RIP
UDP
To and from the IP Office to other RIP devices. For RIP1 and RIP2 (RIP1
compatible) the destination address is a subnet broadcast, eg. 192.168.42.255.
For RIP2 Multicast the destination address is 224.0.0.9.
1701
L2TP
UDP
Layer 2 tunneling protocol.
1718
H.323
UDP
H.323 Discovery
1719
H.323 RAS
UDP
H.323 Status. VoIP device registering with the IP Office.
1720
H.323/H.245
UDP
H.323 Signalling. Data to a registered VoIP device.
UDP
PC Wallboard to CCC Wallboard Server.
2127
(UDP)
Function
3478
SIP
UDP
Port used for STUN requests from the IP Office to the SIP provider.
5005
RTCPMon
UDP
RTCP Monitoring information from Avaya H323 phones.
5060
SIP
UDP/
TCP*
SIP Line Signalling
8080
HTTP
TCP
Browser access to the Delta Server application.
8089
Enconf
UDP
From the IP Office to the Conferencing Center Server Service. User access to the
Conferencing Center is direct via HTTP sessions.
8888
HTTP
TCP
Browser access to the IP Office ContactStore (VRL) application.
IP Office Standard Version Installation
IP Office 7.0
Page 366
15-601042 Issue 23e (16 March 2011)
System Components: Applications
Port
Protocol
Function
49152
to
53247
*
RTP/RTCP
UDP
Dynamically allocated ports used during VoIP calls for RTP and RTCP traffic. The
port range can be adjusted through the System | Gatekeeper tab.
50791
IPO Voicemail
UDP
To voicemail server address.
50793
IPO Solo
Voicemail
UDP
From IP Office TAPI PC with Wave drive user support.
50794
IPO Monitor
UDP
From the IP Office Monitor application.
50795
IPO Voice
Networking
UDP
Small Community Network signalling (AVRIP) and BLF updates. Each system does
a broadcast every 30 seconds. BLF updates are sent required up a maximum of
every 0.5 seconds.
50796
IPO PCPartner UDP
From an IP Office application (for example Phone Manager or SoftConsole). Used
to initiate a session between the IP Office and the application.
50797
IPO TAPI
UDP
From an IP Office TAPI user PC.
50798
(UDP)
UDP
BT Fusion variant. No longer used.
50799
IPO BLF
UDP
Broadcast to the IP Office LAN and the first 10 IP addresses registered from other
subnets.
50800
IPO License
Dongle
UDP
To the License Server IP Address set in the IP Office configuration.
50801
EConf
UDP
Conferencing Center Service to IP Office.
50802
Discovery
TCP
IP Office discovery from Manager.
50804
*
Service Access TCP
Protocol
50805
*
TCP
50808
*
TCP
IP Office system status access.
50812
*
TCP
IP Office security settings access.
50813
*
TCP
IP Office configuration settings access.
" TLS Secure.
" TLS Secure.
· CDR/SMDR from the IP Office is sent to the port number and IP address defined during configuration and using either
TCP or UDP as selected.
IP Office Standard Version Installation
IP Office 7.0
Page 367
15-601042 Issue 23e (16 March 2011)
Ports
IP Office Monitor can be used to display IP packet details including the source and destination Port numbers. As well as
displaying the port numbers (in decimal), IP Office Monitor also displays the names of more commonly used ports
including IP Office specific ports.
For example "src = 23" is interpreted as "src = 23 (Telnet)".
The list below details the ports currently decoded by IP Office Monitor. For a full list of assigned non-IP Office ports see
http://www.iana.org/assignments/port-numbers.
· 20 File Transfer [Default Data]
· 156 SQL Service
· 21 File Transfer [Control]
· 161 SNMP
· 23 Telnet
· 162 SNMPTRAP
· 25 Simple Mail Transfer
· 179 Border Gateway Protocol
· 37 Time
· 1719 H.323Ras
· 43 Who Is
· 1720 H.323/H.245
· 53 Domain Name Server
· 50791 IPO Voicemail
· 67 Bootstrap Protocol Server
· 50792 IPO Network DTE
· 68 Bootstrap Protocol Client
· 50793 IPO Solo Voicemail (i.e. Wave driver for TAPI)
· 69 Trivial File Transfer
· 50794 IPO Monitor
· 70 Gopher
· 50795 IPO Voice Networking
· 79 Finger
· 50796 IPO PCPartner
· 80 World Wide Web-HTTP
· 50797 IPO TAPI
· 115 Simple File Transfer Protocol
· 50798 IPO Who-Is response
· 123 Network Time Protocol
· 50799 IPO BLF
· 137 NETBIOS Name Service
· 50800 IPO License Dongle
· 138 NETBIOS Datagram Service
· 50801 EConf
· 139 NETBIOS Session Service
Protocols
IP Office Monitor, as well as displaying the Protocol number (in decimal) of packets, also displays the names of the more
common Protocols. For example "pcol = 1" is decoded as "pcol = 1 (ICMP)".
Protocol numbers currently decoded by IP Office Monitor are:
· 1 - Internet Control Message [ICMP]
· 2 - Internet Group Management [IGMP]
· 6 - Transmission Control [TCP]
· 8 - Exterior Gateway Protocol [EGP]
· 9 - Interior Gateway Protocol [IGP]
· 17 - User Datagram [UDP]
· 41 - Ipv6 [IPV6]
· 46 - Reservation Protocol [RSVP]
· 47 - General Routing Encapsulation [GRE]
· 58 - ICMP for IPv6 [IPv6-ICMP]
· 111 - IPX in IP[IPX-In-IP]
· 115 - Layer Two Tunneling Protocol [L2TP]
· 121 - Simple Message Protocol [SMP]
IP Office Standard Version Installation
IP Office 7.0
Page 368
15-601042 Issue 23e (16 March 2011)
System Components: Applications
9.15 Operating System Summary
This sections summarizes the support for IP Office applications by IP Office Release 7.0. Some specific features of
applications may have additional requirements. Those requirements will be details in the appropriate application
installation manual.
Windows Operating System Support
The following table gives a summary of the operating systems on which the IP Office applications that are part of the IP
Office Release 7.0 have been tested and are supported. While the applications may function of other operating systems,
they have not been tested by Avaya and are not supported.
IP Office Application
Windows Clients
XP Pro
32
Voicemail Pro Server
64
Vista
32
–
Windows Servers
Windows 7
64
32
64
2003
2008
32
32
64
–
... plus UMS
–
–
–
–
–
–
... plus campaigns
–
–
–
–
–
–
ContactStore
–
–
–
–
–
one-X Portal for IP Office
–
–
–
–
–
–
Customer Call Reporter
–
–
–
–
–
–
Voicemail Pro Client
SoftConsole
–
–
–
–
–
IP Office Manager
System Monitor
System Status Application
TAPI - 1st Party
TAPI - 3rd Party
Phone Manager Lite/Pro
–
–
–
–
–
Phone Manager PC SoftPhone
–
–
–
–
–
· Vista support is only on Business, Enterprise and Ultimate versions.
· Windows 7 support is only on Professional, Enterprise and Ultimate versions.
Virtual Server Support
For IP Office Release 7.0, all applications supported on Windows server operating systems are supported while running on
the following virtual servers:
· VMWare.
· Microsoft Virtual Server.
· Microsoft Server Hyper-V.
Browser Application Support
The following applications are accessed using web browsers. The table below details the browsers tested by Avaya.
Application
Windows
Internet
Explorer
Firefox
Mac
Opera
Safari
Chrome
Safari
IP Office Application Server
7+
3+
2+
3.2+
–
3.2+
Voicemail Pro UMS
7+
3+
2+
3.2+
–
3.2+
one-X Portal for IP Office
7+
3+
2+
3.2+
Customer Call Reporter
7+
3+
2+
3.2+
ContactStore 7.8
7+
–
–
–
–
–
System Status Application
7+
3+
–
–
–
–
3.2+
3.2+
Microsoft Outlook Support
Where IP Office applications interact with Microsoft Outlook, for IP Office Release 6.1, the versions of Outlook supported
are Outlook 2003, Outlook 2007 and Outlook 2010.
IP Office Standard Version Installation
IP Office 7.0
Page 369
15-601042 Issue 23e (16 March 2011)
9.16 Physical Ports
The following port types are found on IP Office systems:
· ANALOG 373
Used for the connection of external analog trunks.
· AUDIO 373
Used for input of an external music on hold source.
· BRI 375
Used for connection of BRI trunks (Quad BRI trunk card). In IP Office Standard Version mode the can also be used
for ISDN terminals devices (So8 module).
· DC I/P 376
Power input from external power supply unit.
· DS 376
Connection of Avaya digital station phones supported by IP Office.
· RS232/DTE 144
Used for control unit maintenance under Avaya guidance. On expansion modules not used.
· EF 377
Emergency power failure ports found on the ETR6 base card.
· ETR 378
Only supported on IP500v2 control unit running in IP Office Essential Edition - PARTNER® Version or IP Office
Essential Edition - Quick Version modes.
· EXPANSION 379
Used for interconnection of external expansions modules and control units.
· EXT O/P 135
Used to control external relay systems. The port provides two switchable (on, off and pulse) controls.
·
Used for connection of functional or protective ground if required.
· LAN 380
10/100Mbps Ethernet LAN ports.
· PF 381
Analog power fails ports.
· PHONE 382 (POT) 382
Analog phone extension ports. On older units these ports are labeled as POT ports.
· PRI 383
PRI trunk ports.
· TCM 384
Connection for M-Series and T-Series phones supported by IP Office. Also for Digital Mobility Solution system
supporting 4100 Series and 7400 Series phones.
· USB
Not used.
IP Office Standard Version Installation
IP Office 7.0
Page 370
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.1 Cables
The IP Office systems are designed primarily for use within an RJ45 structured cabling system using CAT3 unshielded
twisted-pair (UTP) cabling and RJ45 sockets.
A structured cabling system is one where cables are run from a central RJ45 patch panel in the communications/data room
to individual RJ45 sockets at user locations. All wires in each cable between the patch panel and the desk socket are
connected straight through. This arrangement allows devices connected at the patch panel to be swapped to match the
type of device that needs to be connected at the user socket. For example, making one user socket a phone port and
another user socket a computer LAN port, without requiring any rewiring of the cables between the patch panel and the
user location.
· Traditional IDC Punchdown Wiring Installations
Where necessary, the far end RJ45 plug can be stripped from IP Office cables and wired into traditional wiring
systems using punch-block connectors. This type of installation should be performed by an experienced wiring
technician.
· Trunk Connections
The majority of IP Office trunk ports use RJ45 connectors for acceptance of an RJ45-to-RJ45 cable. However,
connection at the line provider's end may require use of a different plug type in order to match the line providers
equipment.
· RJ11 Phone Connectors
Many phones use RJ11 sockets and are supplied with RJ11-to-RJ11 cables. RJ11 plugs can be inserted into RJ45
sockets and in many case the connection will work. However this is not recommended or supported as the
connection lock is not truly positive and may become disconnected. An RJ45-to-RJ11 cable 376 is available for these
connections.
IP Office Standard Version Installation
IP Office 7.0
Page 371
15-601042 Issue 23e (16 March 2011)
Standard IP Office Cables
The following are Avaya standard cables available for use with IP Office systems. The maximum length is applicable if the
standard Avaya cable is replaced with an alternate cable.
Cable
9-Way DTE Cable
144
Description
SAP Code
Standard
Length
Maximum
Length
Connects to control unit RS232 DTE port. 9Way D-type plug to 9-way D-type socket.
–
2m/6'6''.
2m/6'6''.
Structured Cabling DS Line
Cable 376
Connects from RJ45 sockets to RJ11 socketed TT700047871 4m/13'2''.
DS and analog phones.
See table
below.
BRI/PRI Trunk Cable
375
Connects BRI/PRI trunk ports to the line
700213440
provider's network termination point. RJ45 to
RJ45. Red.
3m/9'10''.
–
Expansion Interconnect
Cable 379
Connects the control unit to expansion
700213457
modules. RJ45 to RJ45. Blue. May be replaced
by a yellow interconnect cable (2m (6'6") 700472871) supplied with the IP500 4-Port
Expansion 208 card when using that card.
1m/3'3''.
1m/3'3''.
LAN Cable
Connects from IP Office LAN ports to IP
devices. RJ45 to RJ45. Grey.
3m/9'10''.
100m/328'.
380
700213481
The table below details the maximum total cable distances for DS and analog extensions using different cable types.
Unshielded Twisted-Pair (UTP) - 50nf/Km
Telephone
CW1308
AWG22
(0.65mm)
AWG24
(0.5mm)
AWG26
(0.4mm)
1400 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
2400/5400 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
4406D Phone
1000m/3280'.
1000m/3280'.
400m/1310'.
400m/1310'.
4412D Phone
1000m/3280'.
700m/2295'.
400m/1310'.
400m/1310'.
4424D
500m/1640'.
500m/1640'.
400m/1310'.
400m/1310'.
6400 Series
1000m/3280'.
1000m/3280'.
400m/1310'.
400m/1310'.
9400/9500 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
T3 Series (Upn)
1000m/3280'.
1000m/3280'.
400m/1310'.
–
TCM (without power
booster)
–
305m/1000'
–
–
" (with power
booster)
–
790m/2600'
–
–
Analog Phones
1000m/3280'.
1000m/ 3280'.
400m/1640'.
800m/2620'.
305m/1000'.
305m/1000'.
122m/400'.
122m/400'.
ETR Phones
IP Office Standard Version Installation
IP Office 7.0
Page 372
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.2 ANALOG Port
These ports are analog trunk ports. The IP400 ATM4 analog trunk cards and IP500 analog trunk cards only support loopstart trunks. The ATM16 Analog Trunk module supports both loop-start and ground-start trunks, switchable within the IP
Office configuration.
ANALOG
Pin
Description
1
Not used.
2
Not used.
3
Not used.
4
Ring.
5
Tip.
6
Not used.
7
Not used.
8
Not used.
· Off-Hook Current: 25mA.
·
IMPORTANT
In all IP Office installations, any module being used for analog trunk connections must be connected to a functional
earth 38 .
·
WARNING
Within the Republic of South Africa and in areas of high lightning risk, any module using analog trunk connections
must be connected to a protective ground 38 and to surge protection equipment 39 .
9.16.3 AUDIO Port
This port is found on the rear of all IP Office control units. It is used for the input of an external music-on-hold sound
source. Note that if the IP Office has loaded an internal music-on-hold sound file, any input from this socket is ignored.
The port is a 3.5mm stereo jack socket suitable for use with the most standard audio leads and connection to the
'headphone' output socket of most audio systems.
The use of a 'headphone' socket allows simple volume adjustment. Connection via a 'Line Out' socket may require
additional equipment in order to adjust the volume level.
Pin No.
Description
Common
Common
Left
Audio In - Left Channel.
Right
Audio In - Right - Channel.
· Input impedance: 10k /channel. Maximum a.c. signal – 200mV rms.
IP Office Standard Version Installation
IP Office 7.0
Page 373
15-601042 Issue 23e (16 March 2011)
9.16.4 BRI Port (So)
The BRI ports found on the front of the So8 module are BRI So interface ports for connect to ISDN terminal devices.
For IP Office 4.2+, IP500 BRI trunk daughter cards can be switched from To to So mode. IP400 BRI trunk cards can only
be used as To connections 375 .
IP Office
RJ45
Wire
Pin
BRI
ISDN Terminal
PIN
1
–
White/Orange
1
2
–
Orange/White
2
3
Rx-A
White/Green
3
4
Tx-B
Blue/White
4
5
Tx-A
White/Blue
5
6
Rx-B
Green/White
6
7
–
White/Brown
7
8
–
Brown/White
8
RJ45
· Terminating Resistors
100ohm Terminating resistors are required across the transmit and receive wire pairs at each end of the S-bus.
· The IP Office So8 module BRI ports include integral 100ohm terminating resistors.
· For IP Office 4.2+, individual ports of an IP500 BRI daughter card can be switched to So mode. This is done by
setting the Line Sub-Type to S-Bus in the IP Office configuration. In this case terminating resistors must be added
at the IP Office end in addition to those at the other end of the S-bus connection.
· Addition of the necessary termination at the IP Office end can be done using an IP500 BRI So Converter Cable
(700458649). This short (25cm/10") cable includes both the necessary terminating resistors and the cable
cross-over.
· Many ISDN terminal devices includes terminating resistors. If this is not the case, 100ohm (+/-5%) resistors must
be connected across the receive wire pair and the transmit wire pair in the junction box immediately before the last
ISDN terminal on the S-bus.
IP Office Standard Version Installation
IP Office 7.0
Page 374
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.5 BRI Port (To)
These ports are BRI To interface ports for connection to external BRI trunk services. Note that BRI ports found on the
IP400 So8 module are BRI-S interface ports for connect to ISDN terminal devices, see BRI Port (So) 374 .
PRI/BRI Trunk Cable
This cable is used to connect from IP Office BRI/PRI trunk ports to the line providers network termination equipment. If
that equipment does not use RJ45 sockets, the cable may need to be stripped and rewired or an alternate cable used. The
appropriate signal pin-outs and wire colours are detailed below.
IP Office
BRI
Wire
RJ45
BRI
PRI
Network
Termination
PIN
1
–
Rx-A
White/Orange
1
2
–
Rx-B
Orange/White
2
3
Tx-A
White/Green
3
4
Rx-A
Tx-A
Blue/White
4
5
Rx-B
Tx-B
White/Blue
5
6
Tx-B
–
–
Green/White
6
7
–
–
White/Brown
7
8
–
–
Brown/White
8
RJ45
· Supply: BRI/PRI trunks cards are not supplied with these cables.
· Cable Color: Red.
· SAP Code: 700213440.
· Standard Length: 3m/9'10".
· Maximum Length: 5m/16'5''.
· Though not used pins 7 and 8 are through connected for ease of construction.
IP Office Standard Version Installation
IP Office 7.0
Page 375
15-601042 Issue 23e (16 March 2011)
9.16.6 DC I/P Port
Found on all IP Office control units and expansion modules. Used for connection from the external power supply unit
supplied with the control unit or module.
33
· No other type of power supply unit should be used with the module or module unless specifically indicated by Avaya.
· Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
9.16.7 DS Ports
These ports are used for connection from an RJ45 structured cabling system to digital station phones supported by the IP
Office. DS ports are provided by IP500 Digital Station Cards 212 , IP500 ATM Combination Cards 210 , IP500 BRI
Combination Cards 211 and IP500 Digital Station 229 external expansion modules.
Though the RJ11 to RJ11 cables supplied with some phones can be plugged directly into RJ45 ports including those on IP
Office modules, this is not recommend as the connection lock is not positive and may become disconnected.
DS ports on Digital Station V1/V2 expansion modules can be connected to out-of-building extensions 39 . If this is the
case, connection must be made via suitable protective devices at each end and via each building primary protection. In
addition the Digital Station module must be connected to a protective ground.
DS ports on IP Office control units must not be connected to out-of-building extensions.
Structured Cabling Line Cord
This is an RJ45 to RJ11 cable suitable for connection from a structured cabling system RJ45 port to a DS phone. It can also
be used for two-wire analog phone extensions.
This cable is not suitable for connection from an Avaya 1151D1/B2 power supply unit to a DS phone with a 4450, EU24 or
XM24 add-on module. In those cases the cables supplied with the power supply unit and the add-on module should be
used.
IP Office
DS Port
Phone
Pin
Description
Pin
1
Not used.
–
2
Not used.
1
3
Not used.
2
4
Signal 1.
3
5
Signal 2.
4
6
Not used.
5
7
Not used.
6
8
Not used.
–
Port
· SAP Code: T700047871.
IP Office Standard Version Installation
IP Office 7.0
Page 376
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.8 EF Port
These ports are found on the ETR6 base card. They are analog trunk ports that are only useable when the card is fitted
with an IP500 ATM4 trunk daughter card. When in power fail, the EF ports are connected to trunk port 12.
9.16.9 RS232 DTE Port
These ports are found on the rear of all IP Office control units and external expansion modules. The DTE ports on external
expansion modules are not used.
The RS232 DTE ports on the control units can be used for system maintenance and connection of serial terminal adaptors.
On IP400 control units the port can also be used for connection of the IP Office serial port licence key dongle.
An asynchronous terminal program such as HyperTerminal is also required. Configure this for operation via a PC serial
port, as follows:
Bits per second 38,400
Data bits 8
Parity None
Stop Bits 1
Flow Control None
Settings | Emulation TTY
DTE Cables
These cables are used for system maintenance and diagnostics under Avaya guidance. They can also be used for
connection of RS232 serial terminal adaptor equipment to the IP Office control unit. The cable required depends on the IP
Office control unit. This cable is a "Straight through DB9 female to DB9 male serial cable".
IP Office 9-Way RS232 Signal
DTE Port
PC/Terminal
Adaptor
3
Receive data
3
2
Transmit Data
2
7
RTS (Request To Send)
7
8
CTS (Clear To Send)
8
6
DSR (Data Set Ready)
6
5
Ground
5
1
DCD (Data Carrier Detect)
1
4
DTR (Data Terminal Ready)
4
9
RI (Ring Indicator)
9
IP Office Standard Version Installation
IP Office 7.0
Page 377
15-601042 Issue 23e (16 March 2011)
9.16.10 ETR Port
ETR (Enhanced Tip and Ring) ports are provided by the ETR6 base card. They can be used for the connection of DTMF
analog phone devices and Avaya ETR phones.
IP Office Standard Version Installation
IP Office 7.0
Page 378
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.11 EXPANSION Port
This type of port is found on the rear of IP Office control units and external expansion modules. It is used for connecting
the external expansion modules to there parent IP Office control unit.
The connection between these ports should only be done using an Avaya Expansion Interconnect Cable. No other cable
type should be used.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
· When connecting to expansion ports on an IP500 4-Port Expansion card, a yellow 2 meter (6'6") expansion
interconnect cable can be used in place of the standard blue cable. 4 Yellow cables are supplied with the IP500
4-Port Expansion card.
Expansion Interconnect Cable
The Expansion Interconnect cable is used to link expansion ports between the IP Office control unit and external expansion
modules.
· Supply: One cable is normally supplied with each external expansion module.
· SAP Code: 1m (3'3") Blue cable - 700213457, 2m (6'6") Yellow cable - 700472871.
9.16.12 EXT O/P Port
These ports are found on the rear of all IP Office control units. They are used for connection to external switching relays.
The port uses a standard 3.5mm stereo jack plug for connection.
The IP Office is able to open (high resistance), close (low resistance) or pulse (close for 5 seconds and then open) two
switches within the port. Either switch can be operated separately. These switches are intended for activation of external
relays in systems such as door opening systems.
· CAUTION: In installations where this port is connected to a device external to the building, connection must be via a
towerMAX SCL/8 Surge Protector and a protective ground connection must be provided on the IP Office control unit.
EXT O/P
Pin
Description
1
Switch 1.
2
Switch 2.
3
0 Volts (Ground/Chassis)
· Switching Capacity: 0.7A.
· Maximum Voltage: 55V d.c.
· On state resistance: 0.7 ohms.
· Short circuit current: 1A.
· Reverse circuit current capacity: 1.4A.
· Ensure that pins 1 and 2 are always at a positive voltage with respect to pin 3.
3.5mm stereo audio jack plugs are frequently sold as pre-wired sealed modules. It may be necessary to use a multi-meter
to determine the wiring connections from an available plug. Typically 3 (common to both relays) is the cable screen.
IP Office Standard Version Installation
IP Office 7.0
Page 379
15-601042 Issue 23e (16 March 2011)
9.16.13 LAN Port
These ports are found on IP Office control units. They are used for connection to IP LANs and IP devices.
All IP Office LAN ports are 10/100Mbps auto-sensing. Operation varies as follows:
· IP Office 500 / IP500v2
The ports are full-duplex 10/100Mbps auto-sensing, MDI crossover ports. They form a managed layer 3 Ethernet
switch. The WAN port is not supported on systems running in IP Office Essential Edition - PARTNER® Version, IP
Office Essential Edition - Norstar Version or IP Office Essential Edition - Quick Version modes.
The LEDs are used as follows:
· Green: On = connected, Flashing = Activity.
· Yellow: On = 100Mbps, Off = 10Mbps.
LAN Cables
These are CAT5 UTP cables for connection of various IP devices within the IP Office system.
IP Office
LAN
Pin
MDIX
(Normal)
MDI
(Crossover)
Wire
Standard/
Interconnect
Crossover
1
Rx-A.
Tx-A.
White/Orange
1
3
2
Rx-B.
Tx-B.
Orange/White
2
6
3
Tx-A.
Rx-A.
White/Green
3
1
4
Not used.
Not used.
Blue/White
4
4
5
Not used.
Not used.
White/Blue
5
5
6
Tx-B.
Rx-B.
Green/White
6
2
7
Not used.
Not used.
White/Brown
7
7
8
Not used.
Not used.
Brown/White
8
8
· SAP Code:
· LAN Cable - GREY: 700213481.
Standard straight LAN cable.
· LAN Crossover Cable - Black: 700213473.
LAN crossover cable.
IP Office Standard Version Installation
IP Office 7.0
Page 380
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.14 PF Port
These ports are found on the rear of the IP400 Analog Trunk expansion module. They are analog extension ports that can
be used in conjunction with analog loop-start trunks during power failure to the IP Office system.
Any phones connected to these ports should be clearly labeled as power fail extensions in accordance with the appropriate
national and local regulatory requirements.
PF
Pin
Description
1
Not used.
2
Pin 2 is internally connected to pin 5 via a ringer capacitor.
3
Not used.
4
Ring.
5
Tip.
6
Pin 6 is internally connected to pin 5 via a ringer capacitor.
7
Not used.
8
Not used.
· Minimum Wire Size: AWG 26.
· Maximum Cable Length:
· AWG26: 500m / 1640'.
· AWG24, AWG22: 1000m / 3280'.
IP Office Standard Version Installation
IP Office 7.0
Page 381
15-601042 Issue 23e (16 March 2011)
9.16.15 PHONE (POT) Port
These ports are analog extension ports. On older IP Office units these ports were labeled as POT ports rather than PHONE
ports.
PHONE ports on Phone V1/V2 expansion modules can be connected to out-of-building extensions 39 . If this is the case,
connection must be made via suitable protective devices (IP Office Barrier Box) at each end and via each building primary
protection. In addition the Phone module must be connected to a protective ground.
PHONE ports on IP Office control units must not be connected to out-of-building extensions.
PHONE
Pin
Description
1
Not used.
2
Not used.
3
Not used.
4
Ring.
5
Tip.
6
Not used.
7
Not used.
8
Not used.
· REN: 2
· Off-Hook Current: 25mA.
· Ring Voltage: 40V rms.
· Minimum Wire Size: AWG 26.
· Maximum Cable Length:
· AWG26: 0.5km / 1640 feet.
· AWG24, AWG22: 1km / 3280 feet.
Except on some older equipment, these ports do not include a ringing capacitor. Therefore for connection to 4-wire analog
phones where this is a requirement (typically the United Kingdom and New Zealand), connection should be via a Master
socket containing ringing capacitors. On some older IP403 control units and IP400 Phone V1 modules, pins 2 and 6 are
internally connected via ringing capacitors.
Structured Cabling Line Cord
This is an RJ45 to RJ11 cable suitable for connection from a structured cabling system RJ45 port to a DS phone. It can also
be used for two-wire analog phone extensions.
IP Office
DS Port
Phone
Pin
Description
Pin
1
Not used.
–
2
Not used.
1
3
Not used.
2
4
Signal 1.
3
5
Signal 2.
4
6
Not used.
5
7
Not used.
6
8
Not used.
–
Port
· SAP Code: T700047871.
IP Office Standard Version Installation
IP Office 7.0
Page 382
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.16 PRI Port
These ports are used for connection to PRI trunk services including E1, T1 and E1-R2.
PRI Trunk Cable
This cable is used to connect from IP Office PRI trunk ports to the line providers network termination equipment. If that
equipment does not use RJ45 sockets, the cable may need to be stripped and rewired or an alternate cable used. The
appropriate signal pin-outs and wire colours are detailed below.
IP Office
Wire
RJ45
PRI
Network Termination
PIN
1
Rx-A
White/Orange
1
2
Rx-B
Orange/White
2
3
White/Green
3
4
–
Tx-A
Blue/White
4
5
Tx-B
White/Blue
5
6
–
Green/White
6
7
–
White/Brown
7
8
–
Brown/White
8
RJ45
· Supply: PRI trunks cards are not supplied with these cables.
· Cable Color: Red.
· SAP Code: 700213440.
· Standard Length: 3m/9'10".
IP Office Standard Version Installation
IP Office 7.0
Page 383
15-601042 Issue 23e (16 March 2011)
9.16.17 TCM Port (RJ21)
These ports are used for TCM extension ports in an IP500v2 system. They are found on IP500 Digital Station A 231
external expansion modules. These are supported by IP500v2 systems running IP Office Release 7.0 and higher.
They are used for supported M-Series and T-Series digital stations. They are also used for 4100 and 7400 Series phone
support by connection to a Digital Mobility Solution 349 system.
Cable lengths up to 305 m (1000 ft) using 0.5mm (24AWG) wires do not require a power booster. Lengths up to 790 m
(2600 ft) are supported if an auxiliary power supply booster is used.
1st RJ21 Connector
Port
1
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
10
11
12
13
14
15
16
Not Used
2nd RJ21 Connector
Pin
Wire
Port
26
White/Blue
1
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
Tip
40
Black/Slate
Ring
15
Slate/Black
Tip
41
Ring
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
Wire
26
White/Blue
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
40
Black/Slate
15
Slate/Black
Yellow/Blue
41
Yellow/Blue
16
Blue/Yellow
16
Blue/Yellow
42
Yellow/Orange
42
Yellow/Orange
17
Orange/Yellow
17
Orange/Yellow
43
Violet/Slate
43
Violet/Slate
08
Slate/Violet
08
Slate/Violet
IP Office Standard Version Installation
IP Office 7.0
10
Pin
11
12
13
14
Not Used
Page 384
15-601042 Issue 23e (16 March 2011)
System Components: Physical Ports
9.16.18 TCM Port (RJ45)
These ports are used for TCM extension ports in an IP500v2 system. They are found on IP500 TCM8 Digital Station Cards
215 . These are supported by IP500v2 systems running IP Office Release 7.0 and higher.
They are used for supported M-Series and T-Series digital stations. They are also used for 4100 and 7400 Series phone
support by connection to a Digital Mobility Solution 349 system.
Though the RJ11 to RJ11 cables supplied with some phones can be plugged directly into RJ45 ports including those on IP
Office modules, this is not recommend as the connection lock is not positive and may become disconnected.
Cable lengths up to 305 m (1000 ft) using 0.5mm (24AWG) wires do not require a power booster. Lengths up to 790 m
(2600 ft) are supported if an auxiliary power supply booster is used.
Structured Cabling Line Cord
This is an RJ45 to RJ11 cable suitable for connection from a structured cabling system RJ45 port to a TCM phone. It can
also be used for two-wire analog phone extensions.
IP Office
DS Port
Phone
Pin
Description
Pin
1
Not used.
–
2
Not used.
1
3
Not used.
2
4
Signal 1.
3
5
Signal 2.
4
6
Not used.
5
7
Not used.
6
8
Not used.
–
Port
· SAP Code: T700047871.
IP Office Standard Version Installation
IP Office 7.0
Page 385
15-601042 Issue 23e (16 March 2011)
9.17 Licences
Various IP Office features and applications require entry of license keys into the system's configuration. The license keys
are unique 32-character codes based on the feature being activated and the serial number of the feature key dongle 236
installed with the IP Office system.
The serial number is printed on the feature key dongle and prefixed with SN (IP500) or FK (IP500v2). It can also be
viewed in the system configuration using IP Office Manager.
· For IP500 and IP500v2 systems, the feature key dongle takes the form of a card (smart media or SD card
respectively) inserted into the control unit. The card is a mandatory item for these systems even if they use no
licensed features.
·
When a license key is entered into the IP Office configuration, the following information is shown.
· Status
The status, which is Unknown until the configuration file is sent back to the IP Office system.
· Unknown
This status is shown for licenses that have just been added to the configuration shown in IP Office Manager.
Once the configuration has been sent back to the IP Office and then reloaded, the status will change to one of
those below.
· Valid
The features licensed can be configured and used.
· Invalid
The license was not recognized. It did not match the serial number of the Feature Key.
· Dormant
The license is valid but is conditional on some other pre-requisite licenses.
· Obsolete
The license is valid but is one no longer used by the level of software running on the IP Office system.
· Expired
The license has gone past its expiry date.
· License
The name of the licensed feature. This may differ from the ordered RFA name.
· Instances
Depending on the license, this may be the number of ports enabled or number of simultaneous users of the
licensed feature. Sometime the number of instances is specified in the license name.
· Expires
Most purchased licenses have no expiry setting. For some features, trial licenses may be available which will have
an expiry date.
IP Office Standard Version Installation
IP Office 7.0
Page 386
15-601042 Issue 23e (16 March 2011)
System Components: Licences
9.17.1 System Edition Licenses
These license are used to set what range of features the IP Office system supports.
· Essential Edition
Any IP Office running IP Office Release 5 or higher software is licensed by default for Essential Edition mode (no
license for this is shown in the configuration). The following additional licenses can be added to enable additional
services and features.
·
Essential Edition Additional Voicemail Ports :
IPO LIC R6 ESSNTL EDDITION ADD 2 - 229423.
For IP500v2 only. Unlicensed, the embedded voicemail provided by the system supports 2 simultaneous
connections and 15 hours of storage. This can be expanded up to 6 channels by the addition of licenses, each
of which enables an additional two channels. For IP Office Release7.0+ each license also enables an additional
5 hours of storage.
· Preferred Edition (Voicemail Pro) :
IP400 LIC PREFRD (VMPRO) - 171991.
This license enables support for Voicemail Pro as the IP Office's voicemail server with 4 voicemail ports. The
Preferred Edition license allows the voicemail server to provide the services listed below. Additional license can be
added for additional voicemail features, these are detailed separately. This license was previously called Voicemail
Pro (4 ports).
· Mailboxes for all users and hunt groups.
· Campaigns.
· Announcements for users and hunt groups.
· TTS email reading for users licensed to Mobile
Worker or Power User profiles.
· Customizable call flows.
· Call recording to mailboxes.
· Use of Conference Meet Me functions on IP500
and IP500v2 systems.
· Advanced Edition
This license enables the additional features listed below. A Preferred Edition license is a pre-requisite for this
license.
IPO LIC R6 ADV EDITION RFA LIC:DS - 229424.
·
·
IPO LIC R6 ADV EDITION TRIAL RFA LIC:DS - 229425.
· Support for Customer Call Reporter including 1
supervisor.
· Voicemail Pro Visual Basic Scripting.
· Voicemail Pro call recording to ContactStore.[2]
· Voicemail Pro database interaction (IVR).
· Voicemail Pro call flow generic TTS (8 ports).[1]
1. Provides up to 8 ports of TTS for use with Speak Text actions within Voicemail Pro call flows. Not used for
user TTS email reading.
2. Note: In a Small Community Network using centralized voicemail, this license only enables ContactStore
support for the central IP Office. Remote IP Offices in the network require their own Advanced Edition
license or a VMPro Recordings Administrator license.
Upgrade Licenses
Existing IP Office systems being upgraded to IP Office Release 6.0 or higher may require a software upgrade license.
· New IP500v2 Systems
For the first 90 days, a new IP500v2 control unit will run any supported IP Office Release without requiring an
upgrade license. The highest level run is written into the system's memory (not the SD card) and that becomes a
permanent entitlement for the control unit. However, after 90 days the IP500v2 will require an upgrade license if
upgraded to a software release higher than any that it has run in the initial 90 day period.
·
Warning
Systems upgraded without the appropriate license will display "No license available" and will not allow any
telephony functions.
·
Software Upgrade
Existing IP Office systems being upgraded to IP Office Release 6.0 or higher require an upgrade license. This applies
to all IP Office system modes, for example IP Office standard mode, IP Office Standard Version, IP Office Essential
Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential Edition - Quick
Version modes. There are two types of upgrade licenses as follows:
· Small System Upgrade Licenses:
IPO LIC UPG R7.0 SML - 262645.
This license can be used to upgrade systems with up to 32 users and no external expansion modules.
· Large System Upgrade Licenses:
IPO LIC UPG R7.0 - 262644.
This license can be used to upgrade system with more than 32 users or with external expansion modules.
IP Office Standard Version Installation
IP Office 7.0
Page 387
15-601042 Issue 23e (16 March 2011)
9.17.2 Trunk Licensing
The following trunks licenses can be used by a IP Office Standard Version mode system.
·
IP500 Universal PRI (Additional channels)
These licenses are used to enable additional B-channels above the basic 8 on an IP500 PRI-U card. The IP500 PRI-U
card supports E1, T1 and E1-R2 PRI modes. The IP Office system supports 8 unlicensed B-channels on each IP500
PRI-U port fitted. Additional B-channels, up to the capacity of ports installed and PRI mode selected require
licenses. These additional channels consume the licenses based on which additional channels are configured as inservice from port 9 of slot 1 upwards. D-channels are not affected by licensing.
·
IP500 T1 CHANNELS ADD 2CH - 215180.
IP500 T1 CHANNELS ADD 8CH - 215181.
·
IP500 T1 CHANNELS ADD 32CH - 215182.
·
·
IP500 E1 CHANNELS ADD 2CH - 215183.
IP500 E1 CHANNELS ADD 8CH - 215184.
·
·
IP500 E1 CHANNELS ADD 22CH - 215185.
·
IP500 E1R2 CHANNELS ADD 2CH - 215186.
IP500 E1R2 CHANNELS ADD 8CH - 215187.
·
·
IP500 E1R2 CHANNELS ADD 22CH - 215188.
·
SIP Trunk Channels
These licenses are used to configure the maximum number of simultaneous SIP trunk calls supported. IP Office
Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential Edition Quick Version mode systems support 3 channels without licenses.
·
IPO LIC SIP TRNK RFA 1 - 202967.
IPO LIC SIP TRNK RFA 5 - 202968.
·
IPO LIC SIP TRNK RFA 10 - 202969.
·
·
IPO LIC SIP TRNK RFA 20 - 202970.
·
IP500 Voice Networking
These licenses are used with the IP500 and IP500v2 systems to enable support for SCN, QSIG and H323 IP trunks.
For IP Office Release 5, the additional ports license can be used without requiring a base license first.
·
IP500 VOICE NTWKG ADD LIC RFA - 205650.
9.17.3 Telephone/Endpoint Licenses
The use of H323 and SIP phones with IP Office Release 6+ is controlled by the following licenses. Different licenses are
used for Avaya IP phones, non-Avaya phones (including non-Avaya softphones) and Avaya softphones.
For details of the Phone Manager Pro PC SoftPhone refer to the Other Licenses section
397 .
· Avaya IP Endpoints License
On IP500 and IP500v2 systems, these licenses are used to license additional Avaya IP phones. This includes all
1600, 4600, 5600, 9600, IP DECT, DECT R4, T3 IP, Spectralink and VPN phones supported by IP Office Release 6.
·
IPO LIC R6 AV IP ENDPOINT 1 - 229444.
·
IPO LIC R6 AV IP ENDPOINT 5 - 229445.
IPO LIC R6 AV IP ENDPOINT 20 - 229447.
·
·
IPO LIC R6 AV IP ENDPOINT 5 TRIAL - 229449.
· The system will automatically license 12 Avaya IP phones for each IP500 VCM 32 or VCM 64 card installed in the system
without requiring additional licenses to be added to the configuration.
· Additional Avaya IP phones are licensed either by the addition of Avaya IP Endpoints licenses above or the conversion
of legacy IP500 VCM Channels licenses to Channel Migration licenses (see below).
· By default licenses are consumed by each Avaya IP phone that registers with the IP Office in the order that
they register. The license is released if the phone unregisters. However, it is possible to reserve a license for
particular phones in order to ensure that those phones always obtain a license first if available. This is done
through the Reserve Avaya IP Endpoint Licence setting of each IP extension.
·
Warning
Avaya IP phones without a license will still be able to register but will be limited to making emergency calls
only (Dial Emergency short code calls). The associated user will be treated as if logged off and the phone will
display "No license available" and "Emergency Calls Only". If a license becomes available, it will be assigned to
any unlicensed DECT handsets first and then to any other unlicensed Avaya IP phone in the order that the
phones registered.
· For existing IP500 systems being upgraded to IP Office Release 6, the existing VCM channels and IP500 VCM
Channels license are treated as follows:
IP Office Standard Version Installation
IP Office 7.0
Page 388
15-601042 Issue 23e (16 March 2011)
System Components: Licences
· For each IP400 VCM card installed in the system, each VCM channel supported by the card allows support
for 3 Avaya IP phones.
· For each IP500 VCM32 and IP500 VCM64 card installed in the system, the 4 unlicensed VCM channels
previously provided by each card are converted to allow unlicensed support of 12 Avaya IP phones.
· For each legacy IP500 VCM Channels license, the license are converted Channel Migration licenses
supporting 3 Avaya IP phones. See the Channel Migration license below.
· The IP500 VCM 32 and IP500 VCM 64 cards will provide their full capacity of VCM channels, ie. providing
up to 32 or 64 channels depending on the card type and the codecs being used.
· 3rd Party IP Endpoints License
These licenses are used for support of non-Avaya IP phones including SIP extensions. The available license are used
in order of phone registration. If no licenses are available the phone will not be able to register. Available licenses
can reserved for a particular phone using the Reserve 3rd Party IP Endpoint License setting in the each IP
extension. This license was previously called the IP End-points license.
IP400 IP ENDPOINTS RFA 1 LIC - 174956.
·
IP400 IP ENDPOINTS RFA 5 LIC - 174957.
·
·
IP400 IP ENDPOINTS RFA 20 LIC - 174959.
Legacy Endpoint Licenses
· Channel Migration
These licenses were previously called IP500 VCM Channels. In pre-IP Office Release 6 systems, these license
were used to enable additional VCM channels on IP500 VCM32 and IP500 VCM 64 cards. For IP Office Release 6
these license are no longer required. Any present in the configuration of systems upgraded to IP Office Release 6
are renamed Channel Migration. Each Channel Migration license instance enables support for 3 Avaya IP phones.
IPO LIC IP500 VCM LIC 4 CH LIC - 202961.
·
·
IPO LIC IP500 VCM LIC 8 CH LIC - 202962.
·
IPO LIC IP500 VCM LIC 16 CH LIC - 202963.
·
IPO LIC IP500 VCM LIC 28 CH LIC - 202964.
IPO LIC IP500 VCM LIC 60 CH LIC - 202965.
·
IP Office Standard Version Installation
IP Office 7.0
Page 389
15-601042 Issue 23e (16 March 2011)
9.17.4 User Licenses
The features available to a basic IP Office Worker can be enhanced by the addition of 'User Profile' licenses. Once these
licenses are present in the system configuration, the profiles can be applied to selected users through the User | User |
Profile setting in the IP Office configuration.
Basic User
Office
Worker
Teleworker
Mobile
Worker
Power User
one-X Portal for IP Office
Yes[1]
Yes
Yes
–
Yes
" Telecommuter options
Yes[1]
–
Yes
–
Yes
[1]
Yes
Yes
–
Yes
[1]
UMS Web Services
Mobility Features
Yes
Yes
–
–
Yes
Yes
TTS for Email Reading
–
–
–
Yes
Yes
IP Office SIP SoftPhone
–
–
Yes
–
Yes
1. These features are supported for users on systems with the appropriate pre-IP Office Release 6 legacy
licenses.
· Teleworker Profile License
These licenses set the number of users who can have their profile set as Teleworker. For user with this optional,
additional settings are enabled in the IP Office configuration for the following services: one-X Portal for IP Office
with Telecommuter option UMS Web Services and IP Office SIP SoftPhone.
IPO LIC R6 TELEWORKER 1 - 229430.
·
·
IPO LIC R6 TELEWORKER 5 - 229431.
·
IPO LIC R6 TELEWORKER 20 - 229432.
·
IPO LIC R6 TELEWORKER 5 TRIAL - 229433.
· Mobile Worker Profile License
These licenses set the number of users who can have their profile set as Mobile Worker. For user with this
optional, additional settings are enabled in the IP Office configuration for the following services: Mobility Features
and TTS for Email Reading.
·
IPO LIC R6 MOBILE WORKER 1 - 229434.
·
IPO LIC R6 MOBILE WORKER 5 - 229435.
·
IPO LIC R6 MOBILE WORKER 20 - 229436.
·
IPO LIC R6 MOBILE WORKER 5 TRIAL - 229437.
· Office Worker Profile License
These licenses set the number of users who can have their profile set as Office Worker. For user with this
optional, additional settings are enabled in the IP Office configuration for the following services: one-X Portal for
IP Office (no telecommuter features) and UMS Web Services. If no Office Worker Profile licenses are present,
existing legacy Phone Manager Pro (per seat) licenses can be used to enable users for the Office Worker
profile.
·
IPO LIC R6 OFF WORKER RFA 1 - 229438.
IPO LIC R6 OFF WORKER RFA 5 - 229439.
·
·
IPO LIC R6 OFF WORKER RFA 20 - 229440.
·
IPO LIC R6 OFF WORKER 5 TRIAL - 229441.
· Power User Profile License
These licenses set the number of users who can have their profile set as Power User. For user with this optional,
the same additional services as for Teleworker and Mobile Worker are enabled for the user in the IP Office
configuration plus the following service: SoftPhone.
IPO LIC R6 PWR USER 1 - 229426.
·
·
IPO LIC R6 PWR USER 5 - 229427.
·
IPO LIC R6 PWR USER 20 - 229428.
·
IPO LIC R6 PWR USER 5 TRIAL - 229429.
IP Office Standard Version Installation
IP Office 7.0
Page 390
15-601042 Issue 23e (16 March 2011)
System Components: Licences
Legacy User Licenses
The following licenses are no longer available from Avaya but are still supported for systems upgraded to IP Office Release
6.
· Mobility Features
These legacy licenses were used to enable mobility features, for example mobile twinning or mobile call control, for
users set to the Basic User profile.
IPO LIC MOBILE WORKER RFA 1 - 195569.
·
·
IPO LIC MOBILE WORKER RFA 5 - 195570.
·
IPO LIC MOBILE WORKER RFA 20 - 195572.
· one-X Portal for IP Office
These legacy licenses were used to enable one-X Portal for IP Office support for users set to the Basic User profile.
The licenses were purchased as part of the IP Office Release 5 Power User license packages.
· UMS Web Services
These licenses are used to enable UMS voicemail services support for users set to the Basic User
profile. Other users are enabled for UMS through their licensed user profile. These licenses are
also used to license hunt groups for UMS voicemail services.
IPO LIC VMPRO UMS 1 USER - 217880.
·
·
IPO LIC VMPRO UMS 5 USER - 217881.
IPO LIC VMPRO UMS 20 USER - 217883.
·
IP Office Standard Version Installation
IP Office 7.0
Page 391
15-601042 Issue 23e (16 March 2011)
9.17.5 Voicemail Pro Licenses
For IP Office Release 6, support for Voicemail Pro is enable by the addition of a Preferred Edition license.
· Preferred Edition (Voicemail Pro) :
IP400 LIC PREFRD (VMPRO) - 171991.
This license enables support for Voicemail Pro as the IP Office's voicemail server with 4 voicemail ports. The
Preferred Edition license allows the voicemail server to provide the services listed below. Additional license can be
added for additional voicemail features, these are detailed separately. This license was previously called Voicemail
Pro (4 ports).
· Mailboxes for all users and hunt groups.
· Campaigns.
· Announcements for users and hunt groups.
· TTS email reading for users licensed to Mobile
Worker or Power User profiles.
· Customizable call flows.
· Call recording to mailboxes.
· Use of Conference Meet Me functions on IP500
and IP500v2 systems.
· Advanced Edition
This license enables the additional features listed below. A Preferred Edition license is a pre-requisite for this
license.
·
IPO LIC R6 ADV EDITION RFA LIC:DS - 229424.
·
IPO LIC R6 ADV EDITION TRIAL RFA LIC:DS - 229425.
· Support for Customer Call Reporter including 1
supervisor.
· Voicemail Pro Visual Basic Scripting.
· Voicemail Pro call recording to ContactStore.[2]
· Voicemail Pro database interaction (IVR).
· Voicemail Pro call flow generic TTS (8 ports).[1]
1. Provides up to 8 ports of TTS for use with Speak Text actions within Voicemail Pro call flows. Not used for
user TTS email reading.
2. Note: In a Small Community Network using centralized voicemail, this license only enables ContactStore
support for the central IP Office. Remote IP Offices in the network require their own Advanced Edition
license or a VMPro Recordings Administrator license.
· Preferred Edition Additional Voicemail Ports
The required license for Voicemail Pro server support (Preferred Edition (Voicemail Pro)) also enables 4 voicemail
ports. These licenses can be used to add additional voicemail ports up to the maximum capacity of the IP Office
system (IP500 = 40, IP500v2 =40). This license was previously called Additional Voicemail Pro (ports).
·
IPO LIC VM PRO RFA 2 LIC - 174459.
·
IPO LIC VM PRO RFA 4 LIC - 174460.
·
IPO LIC VM PRO RFA 8 LIC - 174461.
·
IPO LIC VM PRO RFA 16 LIC - 174462.
· VMPro Recordings Administrators :
IPO LIC CONTACTSTORE RFA LIC - 187166.
To support ContactStore in a Small Community Network, IP Offices other than the central IP Office require either
their own Advanced Edition license or this license.
· VMPro Networked Messaging :
IPO LIC NTWKD MSGING RFA LIC - 182297.
Enables VPNM (Voicemail Pro Networked Messaging) functionality within Voicemail Pro. This allows message
exchange with remote Voicemail Pro systems and Avaya Interchange systems.
· VMPro TTS (Generic) :
IP400 3rd PARTY TTS LIC RFA - 182303.
This legacy license enables use of text to speech facilities using third party TTS software with Voicemail Pro. One
license per simultaneous instance of TTS usage. For IP Office Release 6 this license is no longer used for user email
reading. The IP Office Advance Edition license also enables 8 ports of generic TTS.
IPO LIC AVAYA TTS RFA 1 - 182299.
· VMPro TTS (ScanSoft) :
This legacy licence enables use of text to speech facilities using Avaya supplied TTS software with Voicemail Pro.
One license per simultaneous instance of TTS usage. For IP Office Release 6 this license is no longer used for user
email reading.
· UMS Web Services
These licenses are used to enable UMS voicemail services support for users set to the Basic User
profile. Other users are enabled for UMS through their licensed user profile. These licenses are
also used to license hunt groups for UMS voicemail services.
·
IPO LIC VMPRO UMS 1 USER - 217880.
·
IPO LIC VMPRO UMS 5 USER - 217881.
·
IPO LIC VMPRO UMS 20 USER - 217883.
IP Office Standard Version Installation
IP Office 7.0
Page 392
15-601042 Issue 23e (16 March 2011)
System Components: Licences
Legacy Voicemail Licenses
The following legacy licenses are still supported by IP Office Release 6.
· UMS Web Services
These licenses are used to enable UMS voicemail services support for users set to the Basic User
profile. Other users are enabled for UMS through their licensed user profile. These licenses are
also used to license hunt groups for UMS voicemail services.
IPO LIC VMPRO UMS 1 USER - 217880.
·
·
IPO LIC VMPRO UMS 5 USER - 217881.
·
IPO LIC VMPRO UMS 20 USER - 217883.
IP400 3RD PARTY IVR LIC RFA - 182298.
· VMPro Database Interface :
This legacy license enables 3rd party database support within Voicemail Pro call flows. For IP Office Release 6 this is
also enabled by the Advanced Edition license.
· VMPro VB Script :
IP400 VB SCRIPTING LIC RFA - 182300.
This legacy license enables Visual Basic Script support with Voicemail Pro. For IP Office Release 6 this is also
enabled by the Advanced Edition license.
IP Office Standard Version Installation
IP Office 7.0
Page 393
15-601042 Issue 23e (16 March 2011)
9.17.6 Customer Call Reporter Licenses
For IP Office Release 6, support for the Customer Call Reporter application is enabled by the presence of Preferred
Edition and Advanced Edition licenses in the IP Office configuration. For system being upgraded to IP Office Release 6,
Customer Call Reporter can alternately be enabled by a legacy CCR Sup license or a CCC Supervisor and CCR CCC Upg
license.
· Preferred Edition (Voicemail Pro) :
IP400 LIC PREFRD (VMPRO) - 171991.
This license enables support for Voicemail Pro as the IP Office's voicemail server with 4 voicemail ports. The
Preferred Edition license allows the voicemail server to provide the services listed below. Additional license can be
added for additional voicemail features, these are detailed separately. This license was previously called Voicemail
Pro (4 ports).
· Mailboxes for all users and hunt groups.
· Campaigns.
· Announcements for users and hunt groups.
· TTS email reading for users licensed to Mobile
Worker or Power User profiles.
· Customizable call flows.
· Call recording to mailboxes.
· Use of Conference Meet Me functions on IP500
and IP500v2 systems.
· Advanced Edition
This license enables the additional features listed below. A Preferred Edition license is a pre-requisite for this
license.
·
IPO LIC R6 ADV EDITION RFA LIC:DS - 229424.
IPO LIC R6 ADV EDITION TRIAL RFA LIC:DS - 229425.
·
· Support for Customer Call Reporter including 1
supervisor.
· Voicemail Pro Visual Basic Scripting.
· Voicemail Pro call recording to ContactStore.[2]
· Voicemail Pro database interaction (IVR).
· Voicemail Pro call flow generic TTS (8 ports).[1]
1. Provides up to 8 ports of TTS for use with Speak Text actions within Voicemail Pro call flows. Not used for
user TTS email reading.
2. Note: In a Small Community Network using centralized voicemail, this license only enables ContactStore
support for the central IP Office. Remote IP Offices in the network require their own Advanced Edition
license or a VMPro Recordings Administrator license.
·
·
·
· Customer Service Agent
These licenses enable the configuration of users as CCR agents. Multiple license can be added for up to the
maximum of 150 agents. A license is consumed for each CCR agent logged in. If no more license are available,
further agents cannot log in. This license was previous called CCR Agent.
IPO LIC CUSTMR SVC AGT RFA 1 - 217650.
IPO LIC CUSTMR SVC AGT RFA 5 - 217651.
IPO LIC CUSTMR SVC AGT RFA 20 - 217653.
· Customer Service Supervisor
This license is used to enable support for CCR supervisor and wallboard accounts. Each license instance enables
both 1 supervisor account and 1 wallboard account. Multiple license can be added for up to 30 supervisors/
wallboards.
·
IPO LIC R6 CUSTMR SVC SPV 1 - 229442.
·
IPO LIC R6 CUSTMR SVC SPV 1 TRIAL - 229443.
IP Office Standard Version Installation
IP Office 7.0
Page 394
15-601042 Issue 23e (16 March 2011)
System Components: Licences
Legacy CCR Licenses
· CCR Sup
These legacy licenses were used to enable support for the Customer Call Reporter application and CCR
supervisors.
IPO CUSTMR CALL REPORTER 1 SPV LIC RFA - 217655.
·
·
IPO CUSTMR CALL REPORTER 10 SPV LIC RFA - 217656.
IPO CUSTMR CALL REPORTER 20 SPV LIC RFA - 217657.
·
· CCR CCC Upg
This license allows legacy CCC application licenses to be used for Customer Call Reporter.
·
IPO LIC CUSTMR CALL REPORTER UPG LIC RFA - 217658.
·
CCC Server - Enables 1 supervisor, 1 wallboard and 5 agents.
·
CCC Supervisors - Enables the equivalent number of supervisors and wallboards.
·
CCC Agents - Enables the equivalent number of agents.
IP Office Standard Version Installation
IP Office 7.0
Page 395
15-601042 Issue 23e (16 March 2011)
9.17.7 Trial Licenses
The following trial licenses can be requested. A trial license is valid for 60 days from the date of issue and can only be
issued once for a particular IP Office Feature Key serial number. Apart from those restrictions, the trial license works the
same as a full license.
· Preferred Edition:
IPO LIC PREFERRD (VM PRO) TRIAL RFA LIC:DS (189782).
· Advanced Edition:
IPO LIC R6 ADV EDITION TRIAL - 229425.
· Power User (5 Users):
IPO LIC R6 PWR USER 5 TRIAL - 229429.
· Teleworker (5 Users):
IPO LIC R6 TELEWORKER 5 TRIAL - 229433.
· Mobile Worker (5 Users):
IPO LIC R6 MOBILE WORKER 5 TRIAL - 229437.
· Office Worker Profile (5 Users):
· Customer Service Agent:
IPO LIC R6 OFFICE WORKER 5 TRIAL - 229441.
IPO LIC CUSTMR SVC AGT RFA TRIAL 5 - 227053.
· Customer Service Supervisor:
IPO LIC R6 CUSTMR SVC SPV 1 TRIAL - 229443.
· Avaya IP Endpoints (5 Extensions):
· Receptionist (Users):
IPO LIC R6 AVAYA IP ENDPOINT 5 TRIAL - 229449.
IPO LIC RECEPTIONIST RFA 1 TRIAL LIC:CU - 189783.
· VMPro Networked Messaging:
IPO LIC NTWKD MSGING TRIAL RFA LIC:DS - 189776.
· VMPro TTS (ScanSoft):
IPO LIC AVAYA TTS TRIAL RFA 1 LIC:CU - 189778.
· VM Pro TTS (Generic):
IPO LIC 3RD PRTY TTS TRIAL RFA LIC:CU -189781.
· Audix Voicemail:
IPO LIC ACM CENTRAL VM TRIAL LIC:DS - 189786.
· IPSec Tunneling:
IPO LIC IPSec VPN RFA TRIAL LIC:DS - 189806.
· SIP Trunk Channels:
IPO LIC SIP TRUNKING TRIAL RFA 5 - 205820.
· IP500 Voice Networking:
IPO LIC IP500 VCE NTWK ADD 4 TRIAL - 205823.
IP Office Standard Version Installation
IP Office 7.0
Page 396
15-601042 Issue 23e (16 March 2011)
System Components: Licences
9.17.8 Other Licenses
IPO LIC RECEPTIONIST RFA - 171987.
· Receptionist:
This license is used to enable support for the IP Office SoftConsole application. This license can only be used by
users set to Receptionist in the IP Office configuration. A maximum of 4 receptionist are supported. This license
was previously called SoftConsole.
· For IP Office Release 6.0 and 6.1, an instance of this license is consumed by each user configured as a
Receptionist. If the user hot desks to another IP Office system in an SCN, their license entitlement is
retained, ie. the remote system does not require a Receptionist license.
· For IP Office Release 7.0, instances of this license are only consumed when the user is using the IP Office
SoftConsole application. If the user hot desks to another IP Office system in an SCN, that system requires an
available license in its configuration.
IPO LIC ACM CENTRAL VM - 177467.
· Audix Voicemail :
Enables IP Office to use a remote Intuity Audix or Modular Messaging system for voicemail rather than requiring a
local voicemail server.
· IPSec Tunneling :
IPO LIC IPSEC VPN RFA - 182301.
Enables the IP Office to initiate and terminate IPSec and L2TP tunnels.
Phone Manager Licenses
These licenses are used for the IP Office Phone Manager application. In addition to entering Phone Manager licenses, each
user is individually configured for the expected Phone Manager type.
· Phone Manager Pro (per seat):
IPO LIC PMGR PRO RFA 1 - 177468.
Allows users to be configured as Phone Manager Pro users. The user's Phone Manager mode is set through the IP
Office configuration (User | Telephony | Phone Manager Type).
IPO LIC PMGR SFTPHN RFA 1 - 171992.
· Phone Manager Pro IP Audio Enabled (per user):
Enables Phone Manager Pro IP softphone operation for a user. Note: Also requires the user to have a Phone
Manager Pro license.
CTI Licenses
· CTI Link Pro :
IPO LIC CTI RFA - 171988
Enables CTI Link Pro functionality (TAPI Link Pro and DEVLink Pro).
IPO LIC TAPI WAV RFA 4 - 177466
· Wave User :
Allows streaming of WAV files, using TAPILink Pro, for 3rd party voice applications. This is a per user license. Note
that TAPI WAV calls use system data channels taken from the same pools as used for voicemail ports. The
maximum number of simultaneous TAPI WAV user calls and voicemail users is determined by the IP Office control
unit type; IP500 = 40, IP500v2 =40.
IP Office Standard Version Installation
IP Office 7.0
Page 397
15-601042 Issue 23e (16 March 2011)
Chapter 10.
Safety Statements
IP Office Standard Version Installation
IP Office 7.0
Page 399
15-601042 Issue 23e (16 March 2011)
10. Safety Statements
The Avaya IP400 Office and IP500 Office modules are intended to be installed by 'Service Personnel' and it is the
responsibility of the Service Personnel to ensure that all subsidiary interconnected equipment is wired correctly and also
meet the safety requirements of IEC60950 or UL60950 where applicable.
·
The CE mark affixed to this equipment means that the module complies with the 1999/5/EC (R&TTE), 89/336/EEC
(EMC) and 72/23EEC (LVD) Directives.
· The Declarations of Conformity (DoC) for the IP400 and IP500 products are available on the IP Office Application
DVD.
·
This warning symbol is found on the base of IP500 modules.
· Refer to Trunk Interface Modules
which country.
401
for information concerning which Trunk Interface module variants are fitted in
In Finland, Norway and Sweden a protective earthing conductor must be attached to the protective earth point on the rear
of the IPO500 and IPO500v2 Servers. See Grounding 90 for more information. In addition the Server must be located in a
restricted access location where equipotential bonding has been applied, for example, in a telecommunication centre.
10.1 Lithium Batteries
A lithium battery is fitted to the real time clock on IP Office IP400 control unit motherboards and the IP500 control unit
motherboard. .
WARNING
The Lithium battery must only be replaced by Avaya personnel or authorized representatives. There is a danger of
explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
10.2 Lightning Protection/Hazard Symbols
Lightning protectors
The buildings lightning protectors must be verified as follow:
1. Check the lightning protectors, at the trunk cable entry point to the building housing the Avaya IP Office, paying
special attention to the lightning protection grounding. Report any problems, in writing, to the telephone company.
2. Equipment that is designed to be connected using internal wiring is typically not lightning protected. Hence, Avaya
IP Office extension cabling must not leave the building. For installations where telephones and/or other standard
(tip/ring) devices are installed in another building then lightning protection is required (see Out of Building
Telephone Installations 39 ).
Hazard Symbol
The shock hazard symbol is intended to alert personnel to electrical hazard or equipment damage. The following
precautions must also be observed when installing telephone equipment:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
4. Always use caution when working with telephone lines.
IP Office Standard Version Installation
IP Office 7.0
Page 400
15-601042 Issue 23e (16 March 2011)
Safety Statements: Lightning Protection/Hazard Symbols
10.3 Trunk Interface Modules
To ensure the validation of the approvals, only the following types of trunk interface cards must be fitted in the following
IP Office control units.
USA/Canada
Product
Quad
BRI
PRI E1
Single
Dual
PRI T1
Single
ATM4
Dual
IP500v2
IP500
Rest of World
Product
Quad
BRI
PRI E1/E1R2
Single
Dual
PRI T1
Single
ATM4
Dual
IP500v2
IP500
Notes
· E1R2 trunks are only supported in CALA and Korea.
IP Office Standard Version Installation
IP Office 7.0
Page 401
15-601042 Issue 23e (16 March 2011)
10.4 Further Information and Product Updates
Further information, including Product and Reference Manual updates, can be obtained from Avaya Dealers and
Distributors or from Avaya's web site: http://www.avaya.com.
This guide is also available from the Avaya's support web site: http://support.avaya.com.
Support Telephone Numbers
For initial help and support, contact your distributor/supplier. The following contact points are for Avaya authorized
partners.
· In the USA only
Avaya provides a toll-tree Customer Helpline 24 hours a day:
· Name: Avaya Technical Support Organization (TSO)
· Customer Helpline: 1 800 628-2888
· Address: 8744 Lucent Blvd., Highlands Ranch, Colorado, 80129 USA
· URL: http://support.avaya.com
If you need assistance when installing, programming, or using your system, call the Helpline or your Avaya
representative. Consultation charges may apply.
· Outside the USA
If you need assistance when installing, programming, or using your system, contact your Avaya representative.
· URL: http://support.avaya.com
10.5 Port Safety Classification
The Avaya IP Office systems have the following ports which are classified as follows:
Port Name
Port Description
Port Classification
PRI port
PRI ISDN connection (NET)
TNV (Operating within the limits of SELV)
BRI ports
BRI ISDN connection (NET)
TNV (Operating within the limits of SELV)
Analog ports
Two wire analog trunk
TNV3
Power fail ports
Two wire analog trunk
TNV3
DTE port
Async Data connection.
SELV
Analog Telephone Ports
Telephone Extension ports
TNV2
Digital Telephone Ports
Telephone Extension ports
SELV
LAN ports
10/100 BaseT attachment to LAN.
SELV
Expansion ports
Expansion Module connector.
SELV
Audio port
Connector for Music on Hold.
SELV
External Control port
Connector for Controlling Ancillary
circuits.
SELV
DC Input port
Connector for DC input power.
SELV
Interconnection circuits shall be selected to provide continued conformance with the requirements of EN 609050:1992/
A3:1995 clause 2.3 for SELV circuits and with the requirements of clause 6 for TNV circuits, after connections between
equipment.
IP Office Standard Version Installation
IP Office 7.0
Page 402
15-601042 Issue 23e (16 March 2011)
Safety Statements: Port Safety Classification
10.6 EMC Directive
889/336/ EEC (EMC Directive) CISPR 22:1993 including A1 + A2, AS/NZ 3548:1995 (ROW)
·
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his or her own expense.
Canadian Department of Communications (DOC)
''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does
not imply that Industry Canada approved the equipment."
EMC Caution for China
IP Office Standard Version Installation
IP Office 7.0
Page 403
15-601042 Issue 23e (16 March 2011)
10.7 Regulatory Instructions for Use
10.7.1 Australia
Connection
Connection of IP400 Office products must be via a Line Isolation Module with a telecommunications compliance label.
BRI Interface
During the configuration, ensure "000" emergency number is not barred, by performing the following:
· Short Code: 000
· Telephone No: 000;
· Function: DialEmergency
Connections to TS013, the following Bearer Capabilities shall not be used:
· 7kHz Audio, Video, Restricted Digital Information.
If unknown type of number is used in calling party number, the network will use the default CLI.
The system must be configured for Point to Multi point connection to comply with Austel requirements for connecting to
TS013 circuits.
As the IP Office does not support emergency dialing after loss of power, the following warning notice should be
recognized:
· WARNING
This equipment will be inoperable when mains power fails.
PRI Interface
During the configuration, ensure "000" emergency number is not barred, by performing the following:
· Short Code: 000
· Telephone No: 000;
· Function: DialEmergency
· WARNING
This equipment will be inoperable during mains power failure.
10.7.2 Canada
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by
the registration number. The abbreviation, IC, before the registration number signifies that registration was performed
based on a Declaration of Conformity indicating that Industry Canada technical specifications were met.
It does not imply that Industry Canada approved the equipment.
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 1. The REN assigned to each terminal
equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of
the Ringer Equivalence Numbers of all the devices does not exceed five.''
IP Office Standard Version Installation
IP Office 7.0
Page 404
15-601042 Issue 23e (16 March 2011)
Safety Statements: Regulatory Instructions for Use
10.7.3 China
IP Office Standard Version Installation
IP Office 7.0
Page 405
15-601042 Issue 23e (16 March 2011)
10.7.4 European Union
1. 999 and 112 calls must not be barred. Doing so will invalidate the approval.
2. All connections at the MDF shall be identifiable by suitable labeling.
3. The CE mark displayed on IP Office equipment indicates the systems compliance with the EMC, LVD, and R&TTE
Directives and common technical regulations for Primary Rate and Basic Rate ISDN.
4. All ports for the connection of other non-telecommunications apparatus have a Safety Extra Low Voltage (SELV) safety
status.
10.7.5 New Zealand
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item
complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom,
nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all
respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is
compatible with all of Telecom's network services.
IP Office Standard Version Installation
IP Office 7.0
Page 406
15-601042 Issue 23e (16 March 2011)
Safety Statements: Regulatory Instructions for Use
10.7.6 FCC Notification
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council on
Terminal Attachments (ACTA). On the rear of this equipment is a label that contains, among other information, a product
identifier in the format US:AAAEQ##TXXX. If requested, this number must be provided to the telephone company.
The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the
telephone line may result in devices not ringing in response to an incoming call. In most, but not all areas, the sum of
RENs should not exceed 5.0. To be certain of the number of devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format US:AAAEQ##TXXX. The digits represented by ## are the REN without a
decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Means of Connection
Connection of this equipment to the telephone network is shown in the following table.
Port
FIC
SOC
USOC Jack
REN
IPO500 PRI 1U,
IPO500 PRI2U,
IP400 PRI-T1
04DU9.BN,
04DU9.DN,
04DU9.IKN,
04DU9.ISN
6.0Y
RJ48C
NA
IPO500 ATM4U
IP400 ATM4U
OL13A, OL13B,
OL13C, 02AC2,
02LA2, 02LB2, 02LC2,
02LR2, 02LS2
9.0Y
RJ45S
0.1B
IPO500 ATM16
OL13A, OL13B,
OL13C,
02AC2, 02GS2,
02LA2, 02LB2, 02LC2,
02LR2, 02LF2
02GS2, 02LS2
9.0Y
RJ45S
0.1B
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact the Technical Service
Center at 1-800-242- 2121 or contact your local Avaya representative. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect the equipment until the problem is resolved.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or corporation commission for information.
IP Office Standard Version Installation
IP Office 7.0
Page 407
15-601042 Issue 23e (16 March 2011)
Equipment With Direct Inward Dialing (“DID”):
Allowing this equipment to be operated in such a manner as to not provide proper answer supervision is a violation of Part
68 of the FCC’s rules.
Proper Answer Supervision is when:
A.This equipment returns answer supervision to the public switched telephone network (PSTN) when DID calls are:
· answered by the called station,
· answered by the attendant,
· routed to a recorded announcement that can be administered by the customer premises equipment (CPE) user.
· Routed to a dial prompt
B.This equipment returns answer supervision signals on all (DID) calls forwarded back to the PSTN.
Permissible exceptions are:
· A call is unanswered.
· A busy tone is received.
· A reorder tone is received.
Avaya attests that this registered equipment is capable of providing users access to interstate providers of operator
services through the use of access codes. Modification of this equipment by call aggregators to block access dialing codes
is a violation of the Telephone Operator Consumers Act of 1990.
Automatic Dialers:
When programming emergency numbers and (or) making test calls to emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call.
2. Perform such activities in the off-peak hours, such as early morning or late evenings.
Toll Restriction and Least Cost Routing Equipment:
The software contained in this equipment to allow user access to the network must be upgraded to recognize newly
established network area codes and exchange codes as they are placed into service.
Failure to upgrade the premises systems or peripheral equipment to recognize the new codes as they are established will
restrict the customer and the customer’s employees from gaining access to the network and to these codes.
FCC Part 68 Supplier’s Declarations of Conformity
Avaya Inc. in the United States of America hereby certifies that the equipment described in this document and bearing a
TIA TSB-168 label identification number complies with the FCC’s Rules and Regulations 47 CFR Part 68, and the
Administrative Council on Terminal Attachments (ACTA) adopted technical criteria.
Avaya further asserts that Avaya handset-equipped terminal equipment described in this document complies with
Paragraph 68.316 of the FCC Rules and Regulations defining Hearing Aid Compatibility and is deemed compatible with
hearing aids.
IP Office Standard Version Installation
IP Office 7.0
Page 408
15-601042 Issue 23e (16 March 2011)
Safety Statements: Regulatory Instructions for Use
10.7.7 Compliance with FCC Rules
Transmit and Receive Gain Settings for PRI/T1 and Analog Ports
The Gain settings are password controlled for use by qualified installation personnel only and must not be made available
to the end user. The default gain settings of 0dB ensures compliance with FCC part 68 section 68.308(b)(5) and TIA/EIAIS-968 Section 4.5.2.5. "Through transmission amplification from ports for the connection of separately registered
equipment or from other network connection ports". Gain setting adjustment by unqualified personnel may result in
violation of the FCC rules. Qualified personnel may adjust gain settings above these levels only where:
1. Measurement is made to ensure that the power levels sent to line at each network interface connected does not
exceed the maximum levels specified in FCC part 68 section 68.308(b) and TIA/EIA-IS-968 Section 4.5 for that
specific interface type.
2. Where gain adjustment away from the default values are made, precautions should be taken to ensure that the
connection of terminal equipment is controlled by qualified installation personnel.
3. To conform with the Receive Objective Loudness Rating at distances greater than 2.7km from the central office, on
analog trunks a receive gain of 1.5dB must be set.
IP Office Standard Version Installation
IP Office 7.0
Page 409
15-601042 Issue 23e (16 March 2011)
Index
Index
A
Add-Ons
201B Recorder 338
4450 Features 339
EU24 Features 342
EU24BL Features 343
Programmable Buttons 339, 342, 343, 346, 348
T3 DSS Features 346
XM24 Features 348
Analog
Phone Barrier Boxes 133
Phone Region Availability 43, 262
Port 370, 373
Trunk Card 24, 239
Application
Call Center 48, 354
Call Logging 48
CD/DVD 48
ContactStore 353
CTI 48
Maintenance 48
Manager 355
Monitor 356
Phone Manager 358
SoftConsole 360
System Status Application 361
TAPI 362
User 48
Voicemail 48
VoiceMail Pro 363
Assessments
Network 45
VoIP 45
Audio
Codec Conversion 46
Port 370
Audio Port 373
Availability of Equipment 9
B
Backup
SD Card 159
Barrier Boxes
Analog Phone 133
Rack Mounting 134
Base Card
Analog Phone 19, 205
Digital Station 19, 205
Legacy Card Carrier 19, 205
VCM 19, 205
Batteries
Lithium 400
BRI
(So) Port 374
(Trunk) Port 375
Port 370
C
Cable
Access Requirements 55
Clearance Requirements 55
Cables
Maximum Cable Distances 36, 371
Standard IP Office 36, 371
Cabling
IP Office Standard Version Installation
IP Office 7.0
Lightening Protection 39, 131
Call Logging Application 48
Call Status
Application 48
Cards
Analog Trunk 240, 241
ATM4 241
ATM4U 240
BRI Trunk 241
E1 PRI 242
E1R2 PRI 243
Embedded Voicemail Memory 25, 244
IP400 Voice Compression Modules 25
IP500 Analog Phone Base 209
IP500 Digital Station Base 212
IP500 Legacy Card Carrier 214
IP500 VCM 216
Modem 25
Small Office Edition Wireless 25
T1 PRI 242
VCM 245
Voice Compression 245
Castle Rock 139
Channels
Compression 46
Clock 110
Compact Business Center
Application 48, 354
Compact Contact Center
Application 48, 354
Compression Channels 46
Conference Center
Application 48
Configuration
Create New 76
Erase 145
Connections
Grounding 38
Out of Building 39, 131
ContactStore
Application 48
Components 353
License Requirements 353
PC Requirements 353
Control Unit
IP406 V2 14
IP412 14
IP500 202
IP500 System Unit 14
Rack Mounting 40
SOE 14
Wall Mounting 40
Copy
SD Card 161
Country
Languages 47
Supported Locales 47
Create Configuration 76
D
Daughter Cards
Analog Trunk 22, 220
BRI Trunk 22, 221
PRI Trunk 222
PRI-U Trunk 22
Trunk 22
DC I/P
Page 411
15-601042 Issue 23e (16 March 2011)
DC I/P
Port 370
DCI I/P Port 376
DECT
Handset 283, 284
Phone 43, 262
Region Availability 43, 262
DevLink Application 48
DS
IROB 132
Phone 43, 132, 262
Port 370, 376
Region Availablility 43, 262
DTE Port 144
Cable requirement 144, 377
RS232 144, 377
Settings 144, 377
Dual PRI
Trunk Card 24, 239
E
Embedded Voicemail
Application 48
Memory Card 25
EMC Cautions
Canadian Department of Communications 403
EMC Caution for China 403
Federal Communications Commission 403
Envirmental Requirements 54
Equipment Availability 9
Expansion
Port 370
Expansion Modules
IP400 Analog Trunk 26
IP400 Analog Trunk 16 248
IP400 Digital Station 26, 252
IP400 Digital Station V2 250
IP400 Phone 26, 256
IP400 Phone V2 254
IP400 So8 26, 258
IP400 WAN3 26
IP500 Analog Trunk 16 225
IP500 BRI So8 227
IP500 Digital Station 26, 229
IP500 Phone 26, 234
IPO 500 Analog Trunk 26
IPO 500 BRI So8 26
Expansion Port 379
EXT O/P
Port 370
EXT O/P Port 135, 379
Extension Numbers
Swapping 124
External Expansion Modules 26
F
Faulty Units 9
FCC Rules 409
Feature Key Server
Application 48
Feature Keys
Parallel 42
Serial 42
Smart Card 42
USB 42
Features
2402D Phone 275
IP Office Standard Version Installation
IP Office 7.0
2410D Phone 276
2420 Phone 277
3616 Phone 278
3620 Phone 279
3626 Phone 280
3641 Phone 281, 283
3645 Phone 282
3711 Phone 284
3810 Phone 289
4406D+ Phone 291
4412D+ Phone 292
4424D+ Phone 293
4601 Phone 294
4602IP Phone 295
4602SW Phone 295
4610SW Phone 296
4620IP Phone 297
4620SW Phone 297
4621SW Phone 298
4625SW Phone 299
5202D Phone 300
5220D Phone 302
5410 Phone 301
5601 Phone 303
5602IP Phone 304
5602SW Phone 304
5610SW Phone 305
5620 Phone 306
5621 Phone 307
T3 Classic 334
T3 Comfort 335
T3 Compact 336
Firewall Exceptiong 366
G
General Information
Training Courses 51
Web Sites 51
Grounding Control Units 38
H
H323
Phones 43, 262
Region Availability 43, 262
Hazard Symbols 400
Hazardous Substances 9
Homologation Statement 400
HP OpenView 139
I
IP Office Operation in
Australia 404
Canada 404
China 405
European Union 406
New Zealand 406
USA 407
IP400
Trunk cards 24, 239
Voice Compression Modules card 25
IP500
Analog Phone Base Card 19, 205
Analog Trunk Daughter Card 22
BRI Trunk Daughter Card 22
Control Unit 202
Digital Station Base Card 19, 205
Legacy Card Carrier Base Card 19, 205
PRI-U Trunk Daughter Card 22
Page 412
15-601042 Issue 23e (16 March 2011)
Index
IP500
Reset Button 143
system 17
Trunk Daughter Card 22
VCM Base Card 19, 205
IP500 Installation
Admin Applications 63
Card 78, 175
Check Card LED 93
Check CPU LED 182
Connect Manager 65
Documentation 72, 173
Expansion Modules 186
Feature Key 179
Grounding 90, 194
Licences 185
Power 180
Rack Mounting 86, 188
Receive Config 184
Start Manager 66
Tools 71, 172
Unpacking 73, 174
Upgrade Software 183
Wall Mounting 190
License Requirements 356
PC Requirements 356
Protocols 366
MS-CRM
Application 48
N
Network Assessments 45
New Configuration 76
O
Operating Systems 369
Out of Building
Connections 39, 131
P
L
LAN
Port 370
LAN Port 380
Licences
ContactStore 353
Manager 355
Monitor 356
Phone Manager 358
SoftConsole 360
Syatem Status Application
TAPI 362
VoiceMail Pro 363
Licenses
PC-Base 42
PC-Less 42
Lightening Portection 400
Lightening Protection 39, 131
Lithium Batteries 400
361
M
Maintenance
Applications 48
Manager
Application 48
Clock Quality 110
Components 355
License Requirements 355
PC Requirements 355
Prefix Dialing 112
Trunks 108
Upgrade Software 125
Memory card
Removal 120, 152, 167
Modem Card 25
Module
Polycom Video 137
Modules
Trunk Interface 401
Monitor
Application 48
Components 356
IP Office Standard Version Installation
IP Office 7.0
Parallel Feature Key 42
PC
Minimum Specifications 369
PC-Base Licensing 42
PC-Less Licensing 42
PF
Port 370
PF Port 381
Phone (POT)
Port 370
Phone (POT) Port 382
Phone 2000 Series
2402D 275
2410D 276
2420 277
Phone 3000 Series
3616 278
3620 279
3626 280
3641 281
3645 282
3701 283
3711 284
3810 289
DECT Handset 283, 284
WiFi 278, 279, 280, 281, 282
Wireless 289
Phone 4000 Series
4406D+ 291
4412D+ 292
4424D+ 293
4601 294
4602IP 295
4602SW 295
4610SW 296
4620 297
4620SW 297
4621SW 298
4625SW 299
Phone 5000 Series
5402D 300
5410 301
5420D 302
5601 303
5602IP 304
5602SW 304
5610SW 305
5620 306
5621 307
Phone Manager
Application 48
Components 358
Page 413
15-601042 Issue 23e (16 March 2011)
Phone Manager
License Requirements 358
PC Requirements 358
Phone T3 Series
Classic 334
Comfort 335
Compact 336
Polycom Video Module 137
Port
Analog 370, 373
Assigned 366
Audio 370, 373
BRI 370
BRI (So) 374
BRI (Trunk) 375
DC I/P 370
DCI I/P 376
Door 135
DS 370, 376
Expansion 370, 379
EXT O/P 135, 370, 379
IP Office 366
LAN 370, 380
PF 370, 381
Phone (POT) 370, 382
PRI 370, 383
RS232/DTE 370
RS323 DTE 144, 377
Safety Classification 402
USB 370
Used 366
WAN 370
Power Supplies
1151C1 33
1151C2 33
Cords 34
Type 40w PSU 33
Type 45W Earthed PSU 33
Type 60W Earthed PSU 33
Uninterrupted Power Supply 35
PRI
Port 370
PRI Port 383
Programmable Buttons 339, 342, 343, 346, 348
Protocols 366
Q
Quad BRI
Trunk Card
24, 239
R
Rack Mounting Control Units 40
Recorder Interface 338
Region Availability
Analog Phone 43, 262
DECT Phone 43, 262
DS Phone 43, 262
H323 Phone 43, 262
Remove
SD Card 120, 152, 167
Requirements
Cable Access 55
Cable Clearance 55
Enviromental 54
Space 55
Wall Mounting 54
Restore
IP Office Standard Version Installation
IP Office 7.0
SD Card 160
RoHS 9
RS232/DTE
Port 370
S
Safety Statement 400
SAP Codes
201B Recorder 338
2402D Phone 275
2410D Phone 276
2420D Phone 277
3616 Phone 278
3620 Phone 279
3626 Phone 280
3641 Phone 283
3711 Phone 284
3810 Phone 289
4406D+ Phone 291
4412D+ Phone 292
4424D+ Phone 293
4450 Programmable Buttons 339
4601 Phone 294
4602IP Phone 295
4602SW Phone 295
4610SW Phone 296
4620IP Phone 297
4620SW Phone 297
4621SW Phone 298
4625SW Phone 299
5402D Phone 300
5410 Phone 301
5420D Phone 302
5601 Phone 303
5602IP Phone 304
5602SW Phone 304
5610SW Phone 305
5620 Phone 306
5621 Phone 307
EU24 Programmable Buttons 342
EU24BL Programmable Buttons 343
T3 Classic 334
T3 Comfort 335
T3 Compact 336
T3 DSS Programmable Buttons 346
XM24 Programmable Buttons 348
SD Card
Backup 159
Copy 161
Removal 120, 152, 167
Restore 160
Security Settings
Default 147
Serial Feature Key 42
Server
Minimum Specifications 369
Single E1 PRI
Trunk Card 24, 239
Single E1R2
Trunk Card 24, 239
Single PRI T1
Trunk Card 24, 239
Small Office Edition
Wireless Card 25
Smart card Feature Key 42
SNMP 139
Enabling 142
Page 414
15-601042 Issue 23e (16 March 2011)
Index
SNMP 139
Installation 140
Port 142
respond 142
Trap Sending 142
SNMP MIBs
Application 48
So8
Example ISDN Terminal 136
Example Video Conference 137
SoftConsole
Application 48
Components 360
License Requirements 360
PC Requirements 360
Software
Erase Core Software 148
Space Requirements 55
Statement
Homologation 400
Safety 400
Supported
Language 47
Locales 47
System Status
Application 48
System Status Application
Components 361
License Requirements 361
PC Requirements 361
T
TAPI
Components 362
License Requirements 362
PC Requirements 362
WAV Driver Application 48
TAPILink Lite
Application 48
TAPIlink Pro Application 48
Training Courses 51
Trunk Interface Modules 401
U
USB
Feature Key
Port 370
42
V
Voice Compression Channels 46
Voicemail Lite
Application 48
VoiceMail Pro
Application 48
Components 363
License Requirements 363
PC Requirements 363
VoIP Assessments 45
W
Wall Mounting Control Units 40
Wall Mounting Requirements 54
WAN
Port 24, 239, 370
Waterproof Phone 279
Web Sites 51
WiFi Phone 278, 279, 280, 281, 282
Wireless Phone 289
IP Office Standard Version Installation
IP Office 7.0
Page 415
15-601042 Issue 23e (16 March 2011)
IP Office Standard Version Installation
IP Office 7.0
Page 417
15-601042 Issue 23e (16 March 2011)
Performance figures and data quoted in this document are typical, and must be
specifically confirmed in writing by Avaya before they become applicable to any
particular order or contract. The company reserves the right to make alterations
or amendments to the detailed specifications at its discretion. The publication of
information in this document does not imply freedom from patent or other
protective rights of Avaya or others.
All trademarks identified by the ® or ™ are registered trademarks or trademarks,
respectively, of Avaya Inc. All other trademarks are the property of their
respective owners.
This document contains proprietary information of Avaya and is not to be
disclosed or used except in accordance with applicable agreements.
© 2011 Avaya Inc. All rights reserved.
IP Office Standard Version Installation
IP Office 7.0
Page 418
15-601042 Issue 23e (16 March 2011)
Download PDF
Similar pages