Aruba 2530 Switch Series data sheet

Data sheet
Aruba 2530 Switch Series
Key features
•Cost-effective, reliable, and secure Aruba Layer 2 switch series.
•ACLs, EEE, traffic prioritization and models with 10 Gigabit uplinks.
•8-, 24-, and 48-port Gigabit or Fast Ethernet models.
•PoE+ models for voice, video, and wireless.
•Supports ClearPass Policy Manager and Airwave Network Management.
Product overview
The Aruba 2530 Switch Series provides security, reliability, and ease of use for enterprises,
branch offices, and SMBs. This series of fully managed switches delivers full Layer 2
capabilities with enhanced access security, ACLs, traffic prioritization, sFlow, and IPv6 host
support. Right size deployment is simple with choice of 8-, 24-, and 48-port models available
with Gigabit or Fast Ethernet ports, optional PoE+, and optional 10GbE uplinks. The 2530
delivers power savings with fanless models, Energy Efficient Ethernet, ability to disable LEDs
and enable port low power mode. These switches provide consistent wired/wireless user
experience with unified management tools such as ClearPass Policy Manager and Airwave
Network Management.
The Aruba 2530 Switch Series offers uplink flexibility with either four Gigabit or two 10 Gigabit
Ethernet uplinks on some 24- and 48-port models. The Gigabit 24- and 48-port models have
either two small form-factor pluggable plus (SFP+) or four small form-factor pluggable (SFP)
slots for fiber connectivity. The Fast Ethernet 24- and 48-port models have two SFPs and two
RJ-45 Gigabit uplinks. The compact and fan-less 8-port switches offer additional flexibility with
two dual-personality ports that can be used as either RJ-45 Gigabit Ethernet or SFP ports. The
PoE+ switch models are IEEE 802.3af- and IEEE 802.3at-compliant with up to 30 W per port,
making them suitable for voice, video, or wireless deployments with PoE+.
Data sheet
Page 2
Features and benefits
Unified Wired and Wireless
•New ClearPass Policy Manager
Support unified wired and wireless policies using Aruba ClearPass Policy Manager
•HTTP redirect function
Supports HPE Intelligent Management Center (IMC) bring your own device (BYOD)
solution
•Switch auto-configuration
Automatically configures switch for different settings such as VLAN, CoS, PoE max power,
and PoE priority when Aruba AP is detected
•New User Role
A set of switch-based policies in areas such as security, authentication, and QoS. A
User Role can be assigned to a group of users or devices, using switch configuration or
ClearPass (YA version software only)
Quality of Service (QoS)
•Traffic prioritization (IEEE 802.1p)
Allows real-time traffic classification with support for eight priority levels mapped to either
two or four queues, and uses weighted deficit round robin (WDRR) or strict priority
•Simplified quality of service (QoS) configuration
––Port-based
Prioritizes traffic by specifying a port and priority level
––VLAN-based
Prioritizes traffic by specifying a VLAN and priority level
•Class of Service (CoS)
Sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3
protocol, TCP/UDP port number, source port, and DiffServ
•Rate limiting
Establishes per-port ingress-enforced maximums for all ingressed traffic or for broadcast,
multicast, or unknown destination traffic
•Layer 4 prioritization
Enables prioritization based on TCP/UDP port numbers
•Flow control
Helps deliver reliable communication during full-duplex operation
Management
•New Zero-Touch ProVisioning (ZTP)
Uses settings in DHCP to enable ZTP with Aruba AirWave Network Management
•Choice of management interfaces
––HTML-based easy-to-use Web GUI
Allows configuration of the switch from any Web browser
––Robust CLI
Provides advanced configuration and diagnostics
––Simple network management protocol (SNMPv1/v2c/v3)
Allows the switch to be managed with a variety of third-party network management
applications
Data sheet
Page 3
•Virtual stacking
Provides single IP address management for up to 16 switches
•sFlow® (RFC 3176)
Delivers wire-speed traffic accounting and monitoring, configured by SNMP and CLI with
three terminal encrypted receivers
•IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
Automates device discovery protocol for easy mapping by network management applications
•Logging
Provides local and remote logging of events via SNMP (v2c and v3) and syslog; provides
log throttling and log filtering to reduce the number of log events generated
•Port mirroring
Provides advanced monitoring and reporting capabilities for statistics, history, alarms,
and events
•Find, fix, and inform
Finds and fixes common network problems automatically, and then informs the administrator
•Friendly port names
Allows assignment of descriptive names to ports
•Dual flash images
Provides independent primary and secondary operating system files for backup
while upgrading
•Multiple configuration files
Are easily stored with a flash image
•Front-panel LEDs
––Locator LEDs
Allows users to set the locator LED on a specific switch to turn on, blink, or turn off; and
simplifies troubleshooting by making it easy to locate a particular switch within a rack of
similar switches
––Per-port LEDs
Provides an at-a-glance view of the status, activity, speed, and full-duplex operation
––Power and fault LEDs
Display issues, if any
•HPE Comware CLI
––Comware-compatible CLI
Bridges the experience of HPE Comware CLI users who are using the HPE ProVision
software CLI
––Display and fundamental Comware CLI commands
Are embedded in the switch CLI as native commands; display output is formatted as on
Comware-based switches, and fundamental commands provide a Comware-familiar initial
switch setup
––Configuration Comware CLI commands
When Comware commands are entered, CLI helps elicit to formulate the correct ProVision
software CLI command
Data sheet
Page 4
•Download software via DHCP
Adds the option to specify the location of switch software via DHCP
•TR-069 support
Enables zero-touch configuration for switches
Connectivity
•IPv6
––IPv6 host
Allows the switch to be deployed and managed at the edge of an IPv6 network
––Dual stack (IPv4/IPv6)
Supports connectivity for both protocols; provides a transition mechanism from
IPv4 to IPv6
––MLD snooping
Forwards IPv6 multicast traffic to appropriate interface; prevents IPv6 multicast traffic
from flooding the network
––IPv6 ACL/QoS
Supports ACL and QoS for IPv6 network traffic on Gigabit and 48 port 10/100 models
––Security
RA Guard, DHCPv6 Protection, Dynamic IPv6 Lockdown (YA version software only)
•IEEE 802.3af Power over Ethernet (PoE)
Provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones, wireless access points, and security cameras
•IEEE 802.3at PoE+
Provides up to 30 W per port to IEEE 802.3 for PoE/PoE+-powered devices such as video IP phones, IEEE 802.11n wireless access points, and advanced pan/tilt/zoom security
cameras (refer to the product specifications for the total PoE power availability)
•Auto-MDIX
Adjusts automatically for straight-through or crossover cables on all ports
•Pre-standard PoE support
Detects and provides power to pre-standard PoE devices (refer to the list of supported
devices in the product FAQs, which can be accessed at hpe.com/networking/support)
•SFP slots
Provides fiber connectivity such as Gigabit-SX, LX, LH, and BX with four SFP slots on all
24- and 48-port Gigabit Ethernet models. Fast Ethernet 24- and 48-port models have two
SFP slots and two RJ-45 Gigabit uplinks; 8-port models have two dual-personality ports
supporting either SFP or RJ-45 Gigabit uplinks
•Dual-personality (RJ-45 or USB micro-B) serial console port
Gives easy access to switch CLI with front-of-switch location and the flexibility of using
either an RJ-45 or USB micro-B serial console port
Data sheet
Page 5
Layer 2 switching
•VLANs
Provides support for 512 VLANs and 4,094 VLAN IDs
•Jumbo packet support
Supports up to 9,220-byte frame size to improve the performance of large data transfers;
8- and 24-port Fast Ethernet models automatically support up to 2,000-byte frames with
no configuration needed
•16K MAC address table
Provides access to many Layer 2 devices
•GARP VLAN Registration Protocol
Allows automatic learning and dynamic assignment of VLANs
•Rapid Per-VLAN Spanning Tree (RPVST+)
Allows each VLAN to build a separate spanning tree to improve link bandwidth usage;
is compatible with PVST+
Security
•ACLs
Accommodates IPv4/IPv6 port and VLAN-based ACLs (IPv6 ACL is supported only on
Gigabit Ethernet and 48-port models.)
•Source-port filtering
Allows only specified ports to communicate with each other
•RADIUS/TACACS+
Eases switch management security administration by using a password authentication
server
•Secure Sockets Layer (SSL)
Encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in
the switch
•Port security
Allows access only to specified MAC addresses, which can be learned or specified by
the administrator
•MAC address lockout
Prevents particular configured MAC addresses from connecting to the network
Data sheet
Page 6
•Multiple user authentication methods
––IEEE 802.1X
Uses an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server to
authenticate in accordance with industry standards
––Web-based authentication
Provides a browser-based environment, similar to IEEE 802.1X, to authenticate clients that
do not support the IEEE 802.1X supplicant
––MAC-based authentication
Authenticates the client with the RADIUS server based on the client’s MAC address
•Secure shell (SSH) v2
Encrypts all transmitted data for safe remote CLI access over IP networks
•Secure shell
Encrypts all transmitted data for safe remote CLI access over IP networks
•STP BPDU port protection
Blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing
forged BPDU attacks
•STP root guard
Protects the root bridge from malicious attacks or configuration mistakes
•Secure management access
Delivers protected encryption of all access methods (CLI, GUI, or MIB) through SSHv2
and SNMPv3
•Custom banner
Displays security policy when users log in to the switch
•Secure FTP
Allows safe file transfer to and from the switch; protects against unwanted file downloads
or unauthorized copying of a switch configuration file
•Protected ports CLI
Offers intuitive CLI to configure the source-port filter feature, by allowing specified ports to
be isolated from all other ports on the switch; the protected port or ports can communicate
only with the uplink or shared resources
Data sheet
Page 7
•Authentication flexibility
––Multiple IEEE 802.1X users per port
Provides authentication for up to 32 IEEE 802.1X users per port; prevents a user from
“piggybacking” on another user’s IEEE 802.1X authentication
––Concurrent IEEE 802.1X and Web or MAC authentication schemes per port
Allows a switch port to accept any IEEE 802.1X and either Web or MAC authentications
•Switch management logon security
Helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
•DHCP protection
Blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
•Dynamic ARP protection
Blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of
network data
•Dynamic IP lockdown
Works with DHCP protection to block traffic from unauthorized hosts, preventing IP source
address spoofing
Convergence
•IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
Facilitates easy mapping using network management applications with LLDP automated
device discovery protocol
•LLDP-MED (Media Endpoint Discovery)
Defines a standard extension of LLDP that stores values for parameters such as QoS and
VLAN to automatically configure network devices such as IP phones
•IP multicast (data-driven IGMP)
Prevents flooding of IP multicast traffic
•PoE and PoE+ allocations
Support multiple methods—automatic, IEEE 802.3at dynamic, LLDP-MED fine grain,
IEEE 802.3af device class, or user specified—to allocate and manage PoE/PoE+ power for
more efficient energy use
•Voice VLAN
Uses LLDP-MED to automatically configure a VLAN for IP phones
•IP multicast (data-driven IGMPv3)
Prevents flooding of IP multicast traffic
•LLDP-CDP compatibility
Receives and recognizes CDP packets from Cisco’s IP phones for seamless interoperation
•Local MAC Authentication
Assigns attributes such as VLAN and QoS using locally configured profile that can be a list
of MAC prefixes Unified Wired and Wireless
•HTTP redirect function
Supports HPE Intelligent Management Center (IMC) bring your own device (BYOD) solution
Data sheet
Page 8
Resiliency and high availability
•Port trunking and link aggregation
––Trunking
Supports up to eight links per trunk to increase bandwidth and create redundant
connections; and supports L2, L3, and L4 trunk load-balancing algorithm (L4 trunk load
balancing is supported only on Gigabit Ethernet and 48-port models.)
––IEEE 802.3ad Link Aggregation Control Protocol (LACP)
Eases configuration of trunks through automatic configuration
•IEEE 802.1s Multiple Spanning Tree
Provides high link availability in multiple VLAN environments by allowing multiple spanning
trees; provides legacy support for IEEE 802.1d and IEEE 802.1w
•SmartLink
Provides easy-to-configure link redundancy of active and standby links
Product architecture
•Energy-efficient design
––IEEE 802.3az
Reduces power consumption during periods of low data activity on Gigabit Ethernet switches
––Port low-power mode
Enables the port to automatically go into low-power mode to conserve energy when no
link is detected
––Fan-less and variable-speed fans
Decreases power consumption in fan-less (all 8-port, 2530-24, and 2530-48 PoE+
switches) as well as variable-speed fan switches
––Port LEDs
Conserves energy by optionally turning off port link and activity LEDs
•Switch on a chip
Provides a highly integrated, high-performance switch design with a nonblocking architecture
Data sheet
Page 9
Flexibility
•Flexible mounting
––Rack mountable
Allows the switch to be mounted on a standard 19-inch rack, with the hardware included
––Wall mountable
Allows the switch to be mounted on a wall, using the hardware included
––Surface mountable
Allows the switch to be mounted above or below a surface (such as a desk or table), using
the hardware included
•Quiet operation
Lowers noise, making it suitable for deployments in acoustically sensitive environments
such as conference rooms and office spaces
•Compact size
Reduces space requirements (refer to the product specifications for the exact dimensions)
Convergence
•Limited Lifetime Warranty:
See hpe.com/networking/warrantysummary for warranty and support information
included with your product purchase.
•Software releases
To find software for your product, refer to hpe.com/networking/support; for details
on the software releases available with your product purchase, refer to hpe.com/
networking/warrantysummary
Data sheet
Page 10
Aruba 2530 Switch Series
Specifications
I/O ports and slots
Physical characteristics
Dimensions
Weight
Memory and processor
Processor
Mounting and enclosure
Aruba 2530-48G-PoE+ Switch
(J9772A)
Aruba 2530-24G-PoE+ Switch
(J9773A)
Aruba 2530-8G-PoE+ Switch
(J9774A)
48 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3at PoE+); Media Type:
Auto-MDIX; Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T:
full only
4 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB
micro-B) serial console port
24 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3at PoE+); Media Type:
Auto-MDIX; Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T:
full only
4 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB
micro-B) serial console port
8 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3at PoE+); Media Type:
Auto-MDIX; Duplex: 10BASE-T/
100BASE-TX: half or full; 1000BASE-T:
full only
2 dual-personality ports; each port can be
used as either an RJ-45 10/100/1000 port
(IEEE 802.3 Type 10BASE-T; IEEE 802.3u
Type100BASE-TX;IEEE802.3ab1000BASE-T
Gigabit Ethernet) or as a SFP slot (for use
with SFP transceivers)
1 dual-personality (RJ-45 or USB micro-B)
serial console port
17.44(w) x 13.00(d) x 1.75(h) in
(44.3 x 32.26 x 4.45 cm) (1U height)
10.4 lb (4.72 kg)
17.44(w) x 13.00(d) x 1.75(h) in
(44.3 x 33.02 x 4.45 cm) (1U height)
8.7 lb (3.95 kg)
10(w) x 6.28(d) x 1.75(h) in
(25.4 x 15.95 x 4.45 cm) (1U height)
2.2 lb (1 kg)
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
3 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
1.5 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
1.5 MB dynamically allocated
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
IPv6 Ready Certified
< 7.4 µs (LIFO 64-byte packets)
< 2.3 µs (LIFO 64-byte packets)
up to 77.3 Mpps (64-byte packets)
104 Gb/s
16000 entries
IPv6 Ready Certified
< 7.4 µs (LIFO 64-byte packets)
< 2.3 µs (LIFO 64-byte packets)
up to 41.6 Mpps (64-byte packets)
56 Gb/s
16000 entries
IPv6 Ready Certified
< 7.4 µs (LIFO 64-byte packets)
< 2.6 µs (LIFO 64-byte packets)
up to 14.8 Mpps (64-byte packets)
20 Gb/s
16000 entries
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 43.6 dB, Pressure: 33.6 dB
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 43.9 dB, Pressure: 39.6 dB
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
Performance
100 Mb Latency
1000 Mb Latency
Throughput
Switching capacity
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative humidity
Altitude
Acoustic
Data sheet
Page 11
Aruba 2530-48G-PoE+ Switch
(J9772A)
Aruba 2530-24G-PoE+ Switch
(J9773A)
Aruba 2530-8G-PoE+ Switch
(J9774A)
50/60 Hz
236 BTU/hr (248.98 kJ/hr), (switch only:
236 BTU/hr; combined switch + max.
PoE devices: 1624 BTU/hr)
100–127/200–240 VAC
5.8/2.9 A
476 W
40.1 W
382 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with
fully loaded PoE (if equipped), 100%
traffic, all ports plugged in, and all
modules populated.
PoE power is the total power budget
available to all PoE ports.
50/60 Hz
135 BTU/hr (142.42 kJ/hr), (switch only:
135 BTU/hr; combined switch + max. PoE
devices: 843 BTU/hr)
100–127/200–240 VAC
3.2/1.6 A
247 W
25.2 W
195 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with
fully loaded PoE (if equipped), 100%
traffic, all ports plugged in, and all
modules populated.
PoE power is the total power budget
available to all PoE ports.
50/60 Hz
65 BTU/hr (68.58 kJ/hr), (switch only:
65 BTU/hr; combined switch + max. PoE
devices: 293 BTU/hr)
100–127/200–240 VAC
1.4 A
86 W
13.4 W
67 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with
fully loaded PoE (if equipped), 100%
traffic, all ports plugged in, and all
modules populated.
PoE power is the total power budget
available to all PoE ports.
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
Notes
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only. When
using SFPs with this product, SFPs with
revision “B” or later (product number
ends with the letter “B” or later, e.g.,
J4858B, J4859C) are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only. When
using SFPs with this product, SFPs with
revision “B” or later (product number
ends with the letter “B” or later, e.g.,
J4858B, J4859C) are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only. When
using SFPs with this product, SFPs with
revision “B” or later (product number
ends with the letter “B” or later, e.g.,
J4858B, J4859C) are required.
Services
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
Current
Maximum power rating
Idle power
PoE power
Notes
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Data sheet
Page 12
Aruba 2530 Switch Series (continued)
Specifications (continued)
I/O ports and slots
Physical characteristics
Dimensions
Weight
Memory and processor
Processor
Mounting and enclosure
Aruba 2530-48-PoE+ Switch (J9778A)
Aruba 2530-24-PoE+ Switch (J9779A)
Aruba 2530-8-PoE+ Switch (J9780A)
48 RJ-45 autosensing 10/100 PoE+ ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3at PoE+);
Media Type: Auto-MDIX; Duplex: half
or full
2 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB
micro-B) serial console port
24 RJ-45 autosensing 10/100 PoE+ ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3at PoE+);
Media Type: Auto-MDIX; Duplex: half
or full
2 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB
micro-B) serial console port
8 RJ-45 autosensing 10/100 PoE+ ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3at PoE+);
Media Type: Auto-MDIX; Duplex: half
or full
2 dual-personality ports; each port can be
used as either an RJ-45 10/100/1000 port
(IEEE 802.3 Type 10BASE-T;
IEEE 802.3u Type 100BASE-TX;
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet) or as a SFP slot (for use with
SFP transceivers) ports
1 dual-personality (RJ-45 or USB
micro-B) serial console port
17.4(w) x 12.7(d) x 1.75(h) in
(44.2 x 32.26 x 4.45 cm) (1U height)
10.1 lb (4.58 kg)
17.4(w) x 12.7(d) x 1.75(h) in
(44.2 x 32.26 x 4.45 cm) (1U height)
8.4 lb (3.81 kg)
10(w) x 6.28(d) x 1.75(h) in
(25.4 x 15.95 x 4.45 cm) (1U height)
2.0 lb (0.91 kg)
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
3 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
1.5 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
1.5 MB dynamically allocated
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
IPv6 Ready Certified
< 6.6 µs (LIFO 64-byte packets)
< 2.2 µs (LIFO 64-byte packets)
up to 13 Mpps (64-byte packets)
17.6 Gb/s
16000 entries
IPv6 Ready Certified
< 1.7 µs (LIFO 64-byte packets)
< 1.1 µs (LIFO 64-byte packets)
up to 9.5 Mpps (64-byte packets)
12.8 Gb/s
16000 entries
IPv6 Ready Certified
< 1.3 µs (LIFO 64-byte packets)
< 1.3 µs (LIFO 64-byte packets)
up to 4.1 Mpps (64-byte packets)
5.6 Gb/s
16000 entries
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
15% to 90% @ 149°F (65°C),
noncondensing
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 37.9 dB, Pressure: 31.8 dB
up to 10,000 ft (3 km)
Power: 40.4 dB, Pressure: 31.7 dB
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
Performance
100 Mb Latency
1000 Mb Latency
Throughput
Switching capacity
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Acoustic
Data sheet
Page 13
Aruba 2530-48-PoE+ Switch (J9778A)
Aruba 2530-24-PoE+ Switch (J9779A)
Aruba 2530-8-PoE+ Switch (J9780A)
50/60 Hz
170 BTU/hr (179.35 kJ/hr), (switch only:
170 BTU/hr; combined switch + max. PoE
devices: 1505 BTU/hr)
100–127/200–240 VAC
5.2/2.6 A
441 W
37.5 W
382 W
Idle power is the actual power consumption
of the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged in,
and all modules populated.
PoE power is the total power budget
available to all PoE ports.
50/60 Hz
99 BTU/hr (104.45 kJ/hr), (switch only:
99 BTU/hr; combined switch + max. PoE
devices: 809 BTU/hr)
100–127/200–240 VAC
2.8/1.4 A
237 W
21.8 W
195 W
Idle power is the actual power consumption
of the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged in,
and all modules populated.
PoE power is the total power budget
available to all PoE ports.
50/60 Hz
29 BTU/hr (30.6 kJ/hr), (switch only: 29 BTU/hr; combined switch + max. PoE
devices: 262 BTU/hr)
100–127/200–240 VAC
1.4 A
76.7 W
5.8 W
67 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with
fully loaded PoE (if equipped), 100%
traffic, all ports plugged in, and all
modules populated.
PoE power is the total power budget
available to all PoE ports.
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro USB);
IEEE 802.3 Ethernet MIB; Repeater MIB;
Ethernet Interface MIB AirWave Network
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro USB);
IEEE 802.3 Ethernet MIB; Repeater MIB;
Ethernet Interface MIB AirWave Network
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
Notes
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs with
this product, SFPs with revision “B” or later
(product number ends with the letter “B” or
later, e.g., J4858B, J4859C) are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs with
this product, SFPs with revision “B” or later
(product number ends with the letter “B” or
later, e.g., J4858B, J4859C) are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only. When using
SFPs with this product, SFPs with revision
“B” or later (product number ends
with the letter “B” or later, e.g., J4858B,
J4859C) are required.
Services
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/services
for details on the service-level descriptions
and product numbers. For details about
services, and response times in your area,
please contact your local Hewlett Packard
Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/services
for details on the service-level descriptions
and product numbers. For details about
services, and response times in your area,
please contact your local Hewlett Packard
Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
Current
Maximum power rating
Idle power
PoE power
Notes
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Data sheet
Page 14
Aruba 2530 Switch Series (continued)
Specifications (continued)
I/O ports and slots
Physical characteristics
Dimensions
Weight
Memory and processor
Processor
Mounting and enclosure
Aruba 2530-48G Switch (J9775A)
Aruba 2530-24G Switch (J9776A)
Aruba 2530-8G Switch (J9777A)
48 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
24 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
8 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Media Type:
Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 dual-personality ports; each port can be
used as either an RJ-45 10/100/1000 port
(IEEE 802.3 Type 10BASE-T; IEEE 802.3u
Type100BASE-TX;IEEE802.3ab 1000BASE-T
Gigabit Ethernet) or as a SFP slot (for use
with SFP transceivers) ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
17.44(w) x 10.00(d) x 1.75(h) in
(44.3 x 25.4 x 4.45 cm) (1U height)
6.8 lb (3.08 kg)
17.44(w) x 10.00(d) x 1.75(h) in
(44.3 x 25.4 x 4.45 cm) (1U height)
6.1 lb (2.77 kg)
10(w) x 6.28(d) x 1.75(h) in
(25.4 x 15.95 x 4.45 cm) (1U height)
2.0 lb (0.91 kg)
ARM9E @ 800 MHz, 128 MB flash, 256 MB
DDR3 DIMM; packet buffer size: 3 MB
dynamically allocated
ARM9E @ 800 MHz, 128 MB flash, 256 MB
DDR3 DIMM; packet buffer size: 1.5 MB
dynamically allocated
ARM9E @ 800 MHz, 128 MB flash, 256 MB
DDR3 DIMM; packet buffer size: 1.5 MB
dynamically allocated
Mounts in an EIA-standard 19-inch telco
rack or equipment cabinet (rack-mounting
kit available); horizontal surface mounting;
wall mounting
Mounts in an EIA-standard 19-inch telco
rack or equipment cabinet (rack-mounting
kit available); horizontal surface mounting;
wall mounting
Mounts in an EIA-standard 19-inch telco
rack or equipment cabinet (rack-mounting
kit available); horizontal surface mounting;
wall mounting
IPv6 Ready Certified
< 7.4 µs (LIFO 64-byte packets)
< 2.3 µs (LIFO 64-byte packets)
up to 77.3 Mpps (64-byte packets)
104 Gb/s
16000 entries
IPv6 Ready Certified
< 7.4 µs (LIFO 64-byte packets)
< 2.3 µs (LIFO 64-byte packets)
up to 41.6 Mpps (64-byte packets)
56 Gb/s
16000 entries
IPv6 Ready Certified
< 7.4 µs (LIFO 64-byte packets)
< 2.6 µs (LIFO 64-byte packets)
up to 14.8 Mpps (64-byte packets)
20 Gb/s
16000 entries
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C), noncondensing
15% to 90% @ 149°F (65°C), noncondensing
15% to 90% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 34.5 dB, Pressure: 31.0 dB
up to 10,000 ft (3 km)
Power: 34.0 dB, Pressure: 26.4 dB
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
Performance
100 Mb Latency
1000 Mb Latency
Throughput
Switching capacity
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage
temperature
Nonoperating/Storage relative
humidity
Altitude
Acoustic
Data sheet
Page 15
Aruba 2530-48G Switch (J9775A)
Aruba 2530-24G Switch (J9776A)
Aruba 2530-8G Switch (J9777A)
50/60 Hz
Achieved Miercom Certified Green Award
203 BTU/hr (214.17 kJ/hr)
50/60 Hz
50/60 Hz
164 BTU/hr (173.02 kJ/hr)
AC voltage
Current
Maximum power rating
Idle power
Notes
100–127/200–240 VAC
1.2/0.7 A
59.5 W
29.5 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
100–127/200–240 VAC
.6/.4 A
48.0 W
28.8 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
63 BTU/hr (66.46 kJ/hr), (switch only: 63 BTU/hr)
100–127/200–240 VAC
0.5 A
18.6 W
13.6 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
Notes
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs
with this product, SFPs with revision “B”
or later (product number ends with the
letter “B” or later, e.g., J4858B, J4859C)
are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs
with this product, SFPs with revision “B”
or later (product number ends with the
letter “B” or later, e.g., J4858B, J4859C)
are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs
with this product, SFPs with revision “B”
or later (product number ends with the
letter “B” or later, e.g., J4858B, J4859C)
are required.
Services
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response times
in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response times
in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response times
in your area, please contact your local
Hewlett Packard Enterprise sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Data sheet
Page 16
Aruba 2530 Switch Series (continued)
Specifications (continued)
I/O ports and slots
Physical characteristics
Dimensions
Weight
Memory and processor
Processor
Mounting and enclosure
Aruba 2530-48 Switch (J9781A)
Aruba 2530-24 Switch (J9782A)
Aruba 2530-8 Switch (J9783A)
48 RJ-45 autosensing 10/100 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
2 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
24 RJ-45 autosensing 10/100 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
2 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 fixed Gigabit Ethernet SFP ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
8 RJ-45 autosensing 10/100 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Media Type:
Auto-MDIX; Duplex: half or full
2 dual-personality ports; each port can be
used as either an RJ-45 10/100/1000 port
(IEEE 802.3 Type 10BASE-T; IEEE 802.3u
Type100BASE-TX;IEEE802.3ab1000BASE-T
Gigabit Ethernet) or as a SFP slot (for use
with SFP transceivers) ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
17.4(w) x 9.7(d) x 1.75(h) in
(44.2 x 24.64 x 4.45 cm) (1U height)
6.3 lb (2.86 kg)
17.4(w) x 9.7(d) x 1.75(h) in
(44.2 x 24.64 x 4.45 cm) (1U height)
5.7 lb (2.59 kg)
10(w) x 6.28(d) x 1.75(h) in
(25.4 x 15.95 x 4.45 cm) (1U height)
1.8 lb (0.82 kg)
ARM9E @ 800 MHz, 128 MB flash, 256 MB
DDR3 DIMM; packet buffer size: 3 MB
dynamically allocated
ARM9E @ 800 MHz, 128 MB flash, 256 MB
DDR3 DIMM; packet buffer size: 1.5 MB
dynamically allocated
ARM9E @ 800 MHz, 128 MB flash, 256 MB
DDR3 DIMM; packet buffer size: 1.5 MB
dynamically allocated
Mounts in an EIA-standard 19-inch telco
rack or equipment cabinet (rack-mounting
kit available); horizontal surface mounting;
wall mounting
Mounts in an EIA-standard 19-inch telco
rack or equipment cabinet (rack-mounting
kit available); horizontal surface mounting;
wall mounting
Mounts in an EIA-standard 19-inch telco
rack or equipment cabinet (rack-mounting
kit available); horizontal surface mounting;
wall mounting
IPv6 Ready Certified
< 6.6 µs (LIFO 64-byte packets)
< 2.2 µs (LIFO 64-byte packets)
up to 13 Mpps (64-byte packets)
17.6 Gb/s
16000 entries
IPv6 Ready Certified
< 1.7 µs (LIFO 64-byte packets)
< 1.1 µs (LIFO 64-byte packets)
up to 9.5 Mpps (64-byte packets)
12.8 Gb/s
16000 entries
IPv6 Ready Certified
< 1.3 µs (LIFO 64-byte packets)
< 1.3 µs (LIFO 64-byte packets)
up to 4.1 Mpps (64-byte packets)
5.6 Gb/s
16000 entries
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C), noncondensing
15% to 90% @ 149°F (65°C), noncondensing
15% to 90% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
Performance
100 Mb Latency
1000 Mb Latency
Throughput
Switching capacity
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage
temperature
Nonoperating/Storage relative
humidity
Altitude
Acoustic
Data sheet
Page 17
Aruba 2530-48 Switch (J9781A)
Aruba 2530-24 Switch (J9782A)
Aruba 2530-8 Switch (J9783A)
50/60 Hz
102 BTU/hr (107.61 kJ/hr)
100–127/200–240 VAC
0.7/0.4 A
29.9 W
17.1 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
50/60 Hz
50 BTU/hr (52.75 kJ/hr)
100–127/200–240 VAC
0.3/0.2 A
14.7 W
8.4 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
50/60 Hz
25 BTU/hr (26.38 kJ/hr)
100–127/200–240 VAC
0.5 A
7.2 W
4.5 W
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning
the infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1;
EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
Notes
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs
with this product, SFPs with revision “B”
or later (product number ends with the
letter “B” or later, e.g., J4858B, J4859C)
are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs
with this product, SFPs with revision “B”
or later (product number ends with the
letter “B” or later, e.g., J4858B, J4859C)
are required.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af apply
to PoE+ models only. When using SFPs
with this product, SFPs with revision “B”
or later (product number ends with the
letter “B” or later, e.g., J4858B, J4859C)
are required.
Services
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response times
in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response times
in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response times
in your area, please contact your local
Hewlett Packard Enterprise sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
Current
Maximum power rating
Idle power
Notes
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
Data sheet
Page 18
Aruba 2530 Switch Series (continued)
Specifications (continued)
Aruba 2530-48G-PoE+-2SFP+ Switch (J9853A)
Aruba 2530-24G-PoE+-2SFP+ Switch (J9854A)
48 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
2 SFP+ fixed 1000/10000 SFP+ ports
1 dual-personality (RJ-45 or USB micro-B) serial
console port
24 RJ-45 autosensing 10/100/1000 PoE+
ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
2 SFP+ fixed 1000/10000 SFP+ ports
1 dual-personality (RJ-45 or USB micro-B) serial
console port
17.44(w) x 13.00(d) x 1.75(h) in (44.3 x 32.26 x 4.45 cm)
(1U height)
10.4 lb (4.72 kg)
17.44(w) x 13.00(d) x 1.75(h) in (44.3 x 33.02 x 4.45 cm)
(1U height)
8.6 lb (3.9 kg)
ARM9E @ 800 MHz, 128 MB flash, 256 MB DDR3 DIMM;
packet buffer size: 3 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash, 256 MB DDR3 DIMM;
packet buffer size: 1.5 MB dynamically allocated
Mounts in an EIA-standard 19-inch telco rack or
equipment cabinet (rack-mounting kit available);
horizontal surface mounting; wall mounting
Mounts in an EIA-standard 19-inch telco rack or
equipment cabinet (rack-mounting kit available);
horizontal surface mounting; wall mounting
100 Mb Latency
1000 Mb Latency
10 Gb/s Latency
Throughput
Switching capacity
MAC address table size
IPv6 Ready Certified
< 7.3 µs (LIFO 64-byte packets)
< 2.7 µs (LIFO 64-byte packets)
< 4.0 µs (LIFO 64-byte packets)
101 Mpps (64-byte packets)
136 Gb/s
16000 entries
IPv6 Ready Certified
< 7.3 µs (LIFO 64-byte packets)
< 2.7 µs (LIFO 64-byte packets)
< 2.2 µs (LIFO 64-byte packets)
65.4 Mpps (64-byte packets)
88 Gb/s
16000 entries
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative humidity
Altitude
Acoustic
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 36.4 dB, Pressure: 30.1 dB
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C), noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C), noncondensing
up to 10,000 ft (3 km)
Power: 31.3 dB, Pressure: 24 dB
I/O ports and slots
Physical characteristics
Dimensions
Weight
Memory and processor
Processor .
Mounting and enclosure
Performance
Data sheet
Page 19
Aruba 2530-48G-PoE+-2SFP+ Switch (J9853A)
Aruba 2530-24G-PoE+-2SFP+ Switch (J9854A)
50/60 Hz
215 BTU/hr (226.83 kJ/hr), (switch only: 215 BTU/hr;
combined switch + max. PoE devices: 1499 BTU/hr)
100–127/200–240 VAC
5.6/2.8 A
439 W
40.2 W
382 W
Idle power is the actual power consumption of the
device with no ports connected. Maximum power
rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided
for planning the infrastructure with fully loaded PoE
(if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE power is the total power budget available to all
PoE ports.
50/60 Hz
118 BTU/hr (124.49 kJ/hr), (switch only: 118 BTU/hr;
combined switch + max. PoE devices: 757 BTU/hr)
100–127/200–240 VAC
2.9/1.4 A
222.2 W
24.7 W
195 W
Idle power is the actual power consumption of the
device with no ports connected. Maximum power
rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided
for planning the infrastructure with fully loaded PoE
(if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE power is the total power budget available to all
PoE ports.
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A; VCCI Class A
FCC Class A; EN 55022/CISPR-22 Class A; VCCI Class A
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center; command-line
interface; Web browser; configuration menu;
out-of-band management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater MIB; Ethernet
Interface MIB
AirWave Network Management
IMC—Intelligent Management Center; command-line
interface; Web browser; configuration menu;
out-of-band management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater MIB; Ethernet
Interface MIB
AirWave Network Management
Notes
IEEE 802.3az applies to Gigabit models only;
IEEE 802.3at and IEEE 802.3af apply to PoE+
models only.
SFPs with revision “B” or later (e.g., J4858B, J4859C) are
required with this product. This product supports only 1 Gigabit SFP & 10 Gigabit SFP+ transceivers, as well as 10 Gigabit Direct Attach Cables.
IEEE 802.3az applies to Gigabit models only;
IEEE 802.3at and IEEE 802.3af apply to PoE+
models only.
SFPs with revision “B” or later (e.g., J4858B, J4859C) are
required with this product. This product supports only 1 Gigabit SFP & 10 Gigabit SFP+ transceivers, as well
as 10 Gigabit Direct Attach Cables.
Services
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the
service-level descriptions and product numbers. For
details about services, and response times in your area,
please contact your local Hewlett Packard Enterprise
sales office.
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the
service-level descriptions and product numbers. For
details about services, and response times in your area,
please contact your local Hewlett Packard Enterprise
sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
Current
Maximum power rating
Idle power
PoE power
Notes
Data sheet
Page 20
Aruba 2530 Switch Series (continued)
Specifications (continued)
I/O ports and slots
Physical characteristics
Dimensions
Weight
Memory and processor
Processor
Mounting and enclosure
Aruba 2530-48G-2SFP+ Switch
(J9855A)
Aruba 2530-24G-2SFP+ Switch
(J9856A)
Aruba 2530-8-PoE+ Internal PS Switch
(JL070A)
48 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 SFP+ fixed 1000/10000 SFP+ ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
24 RJ-45 autosensing 10/100/1000 ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 SFP+ fixed 1000/10000 SFP+ ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
8 RJ-45 autosensing 10/100 PoE+ ports
(IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3at
PoE+); Media Type: Auto-MDIX;
Duplex: half or full 2 dual-personality
ports; each port can be used as
either an RJ-45 10/100/1000 port
(IEEE 802.3 Type 10BASE-T;
IEEE 802.3u Type 100BASE-TX;
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet) or as a SFP slot (for use with
SFP transceivers) ports
1 dual-personality (RJ-45 or USB micro-B)
serial console port
17.44(w) x 10.00(d) x 1.75(h) in
(44.3 x 25.4 x 4.45 cm) (1U height)
7.1 lb (3.08 kg)
17.44(w) x 10.00(d) x 1.75(h) in
(44.3 x 25.4 x 4.45 cm) (1U height)
6.2 lb (2.81 kg)
10(w) x 9.68(d) x 1.75(h) in
(25.4 x 24.59 x 4.45 cm) (1U height)
4.65 lb (2.11 kg)
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
3 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
1.5 MB dynamically allocated
ARM9E @ 800 MHz, 128 MB flash,
256 MB DDR3 DIMM; packet buffer size:
1.5 MB dynamically allocated
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); horizontal
surface mounting; wall mounting
Mounts in an EIA-standard 19-inch
telco rack or equipment cabinet
(rack-mounting kit available); Horizontal
surface mounting; Wall mounting
IPv6 Ready Certified
< 7.3 µs (LIFO 64-byte packets)
< 2.7 µs (LIFO 64-byte packets)
< 4.0 µs (LIFO 64-byte packets)
101 Mpps (64-byte packets)
136 Gb/s
16000 entries
IPv6 Ready Certified
< 7.3 µs (LIFO 64-byte packets)
< 2.7 µs (LIFO 64-byte packets)
< 2.2 µs (LIFO 64-byte packets)
65.4 Mpps (64-byte packets)
88 Gb/s
16000 entries
IPv6 Ready Certified
< 1.3 µs (LIFO 64-byte packets)
< 1.3 µs (LIFO 64-byte packets)
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 32.2 dB, Pressure: 25.6 dB
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 29.4 dB, Pressure: 22.3 dB
32°F to 113°F (0°C to 45°C)
15% to 95% @ 104°F (40°C),
noncondensing
-40°F to 158°F (-40°C to 70°C)
15% to 90% @ 149°F (65°C),
noncondensing
up to 10,000 ft (3 km)
Power: 0 dB, Pressure: 0 dB
Performance
100 Mb Latency
1000 Mb Latency
10 Gb/s Latency
Throughput
Switching capacity
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative
humidity
Altitude
Acoustic
up to 4.1 Mpps (64-byte packets)
5.6 Gbps
16000 entries
Data sheet
Page 21
Aruba 2530-48G-2SFP+ Switch
(J9855A)
Aruba 2530-24G-2SFP+ Switch
(J9856A)
Aruba 2530-8-PoE+ Internal PS Switch
(JL070A)
50/60 Hz
Achieved Miercom Certified Green Award
189 BTU/hr (199.4 kJ/hr)
50/60 Hz
50/60 Hz
104 BTU/hr (109.72 kJ/hr)
AC voltage
Current
Maximum power rating
Idle power
PoE power
Notes
100–127/200–240 VAC
0.9/0.5 A
55.1 W
33.3 W
100–127/200–240 VAC
0.7/0.5 A
31 W
20.5 W
Idle power is the actual power
consumption of the device with no ports
connected. Maximum power rating
and maximum heat dissipation are
the worst-case theoretical maximum
numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
Idle power is the actual power
consumption of the device with no ports
connected. Maximum power rating
and maximum heat dissipation are
the worst-case theoretical maximum
numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated.
29 BTU/hr (30.6 kJ/hr), (switch only:
29 BTU/hr; combined switch + max. PoE
devices: 239 BTU/hr)
100–127/200–240 VAC
0.9/0.5 A
70.2 W
5.3 W
67 W PoE
Idle power is the actual power
consumption of the device with no ports
connected. Maximum power rating
and maximum heat dissipation are
the worst-case theoretical maximum
numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged
in, and all modules populated. PoE power
is the total power budget available to all
PoE ports.
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1
Emissions
FCC Class A; EN 55022/CISPR-22 Class A; FCC Class A; EN 55022/CISPR-22 Class A; FCC Class A; EN 55022/CISPR-22 Class A;
VCCI Class A
VCCI Class A
VCCI Class A
Electrical characteristics
Frequency
Maximum heat dissipation
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
EN 55024, CISPR 24
EN 55024, CISPR 24
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
configuration menu; out-of-band
management (serial RS-232C or Micro
USB); IEEE 802.3 Ethernet MIB; Repeater
MIB; Ethernet Interface MIB AirWave
Network Management
Notes
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only.
SFPs with revision “B” or later (e.g.,
J4858B, J4859C) are required with
this product. This product supports
only 1 Gigabit SFP & 10 Gigabit SFP+
transceivers, as well as 10 Gigabit Direct
Attach Cables.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only.
SFPs with revision “B” or later (e.g.,
J4858B, J4859C) are required with
this product. This product supports
only 1 Gigabit SFP & 10 Gigabit SFP+
transceivers, as well as 10 Gigabit Direct
Attach Cables.
IEEE 802.3az applies to Gigabit models
only; IEEE 802.3at and IEEE 802.3af
apply to PoE+ models only.
When using SFPs with this product,
SFPs with revision “B” or later (product
number ends with the letter “B” or later,
e.g., J4858B, J4859C) are required.
Services
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Refer to the Hewlett Packard Enterprise
website at hpe.com/networking/
services for details on the service-level
descriptions and product numbers. For
details about services, and response
times in your area, please contact
your local Hewlett Packard Enterprise
sales office.
Data sheet
Page 22
Standards and protocols
(applies to all products in series)
Denial of service protection
Network DoS Filter
Device management
RFC 1591 DNS (client)
RFC 2576 (Coexistence between SNMP
V1, V2, V3)
RFC 2579 (SMIv2 Text Conventions)
RFC 2580 (SMIv2 Conformance)
RFC 3416 (SNMP Protocol Operations v2)
RFC 3417 (SNMP Transport Mappings)
SSHv1/SSHv2 Secure Shell
General protocols
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of
Spanning Tree
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ad Link Aggregation Control
Protocol (LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1350 TFTP Protocol (revision 2)
RFC 1542 BOOTP Extensions
RFC 1918 Address Allocation for Private
Internet
RFC 2030 Simple Network Time
Protocol (SNTP) v4
RFC 2131 DHCP
RFC 3411 An Architecture for Describing
Simple Network Management Protocol
(SNMP) Management Frameworks
RFC 3412 Message Processing and
Dispatching for the Simple Network
Management Protocol (SNMP)
RFC 3413 Simple Network Management
Protocol (SNMP) Applications
RFC 3414 User-based Security Model (USM)
for version 3 of the Simple Network
Management Protocol (SNMPv3)
RFC 3415 View-based Access Control
Model (VACM) for the Simple Network
Management Protocol (SNMP)
RFC 3575 IANA Considerations for RADIUS
RFC 5905 NTP Client
IP multicast
RFC 3376 IGMPv3
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over
Ethernet Networks
RFC 2925 Remote Operations MIB (Ping
only)
RFC 3315 DHCPv6 (client only)
RFC 3484 Default Address Selection
for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3596 DNS Extension for IPv6
RFC 3810 Multicast Listener Discovery
Version 2 (MLDv2) for IPv6
RFC 4022 MIB for TCP
RFC 4113 MIB for UDP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4252 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing
Architecture
RFC 4293 MIB for IP
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
RFC 5095 Deprecation of
Type 0 Routing Headers in IPv6
MIBs
RFC 1155 Structure and Identification
of Management Information for TCP/
IP Internets
RFC 1212 Concise MIB Definitions
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 2021 RMONv2 MIB
RFC 2578 Structure of Management
Information Version 2 (SMIv2)
RFC 2579 Textual Conventions for
SMIv2
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q
Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2863 The Interfaces Group MIB
RFC 4836 Managed Objects
for 802.3 Medium Attachment Units
(MAU)
Network management
IEEE 802.1AB Link Layer Discovery
Protocol (LLDP)
RFC 1098 A Simple Network
Management Protocol (SNMP)
RFC 1155 Structure of Management
Information
RFC 2819 Four groups of RMON: 1
(statistics), 2 (history), 3 (alarm) and 9
(events)
RFC 3411 SNMP Management
Frameworks
RFC 3412 Message Processing and
Dispatching for the Simple Network
Management Protocol (SNMP)
RFC 3413 Simple Network Management
Protocol (SNMP) Applications
RFC 3414 User-based Security Model
(USM) for version 3 of the Simple Network
Management Protocol (SNMPv3)
RFC 3415 View-based Access Control
Model (VACM) for the Simple Network
Management Protocol (SNMP)
RFC 3418 Management Information
Base (MIB) for the Simple Network
Management Protocol (SNMP)
RFC 5424 Syslog Protocol
ANSI/TIA-1057 LLDP Media Endpoint
Discovery (LLDP-MED)
SNMPv1/v2c/v3
QoS/CoS
RFC 2474 DiffServ precedence,
with 4 queues per port
RFC 2475 DiffServ Architecture
RFC 2597 DiffServ Assured Forwarding
(AF)
RFC 2598 DiffServ Expedited Forwarding
(EF)
Security
IEEE 802.1X Port Based Network Access
Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2866 RADIUS Accounting
Secure Sockets Layer (SSL)
Data sheet
Page 23
Aruba 2530 Switch Series accessories
Transceivers
HPE X111 100M SFP LC FX Transceiver (J9054C)
HPE X121 1G SFP LC SX Transceiver (J4858C)
HPE X121 1G SFP LC LX Transceiver (J4859C)
HPE X121 1G SFP LC LH Transceiver (J4860C)
HPE X122 1G SFP LC BX-D Transceiver (J9142B)
HPE X122 1G SFP LC BX-U Transceiver (J9143B)
HPE X121 1G SFP RJ45 T Transceiver (J8177C)
Mounting kit
HPE X410 1U Universal 4-post Rack Mounting Kit (J9583A)
Aruba 2530-8-PoE+ Internal PS Switch
(JL070A)
HPE X510 1U Cable Guard (J9700A)
Aruba 2530-8G-PoE+ Switch (J9774A)
Aruba 2530 8-port Switch Power Adapter Shelf (J9820A)
Aruba X510 1U Cable Guard (J9700A)
Aruba 2530-8-PoE+ Switch (J9780A)
Aruba 2530 8-port Switch Power Adapter Shelf (J9820A)
Aruba X510 1U Cable Guard (J9700A)
Aruba 2530-8G Switch (J9777A)
Aruba 2530 8-port Switch Power Adapter Shelf (J9820A)
Aruba X510 1U Cable Guard (J9700A)
Aruba 2530-8 Switch (J9783A)
Aruba 2530 8-port Switch Power Adapter Shelf (J9820A)
HPE X510 1U Cable Guard (J9700A)
Aruba 2530-48G-PoE+-2SFP+ Switch (J9853A)
HPE X132 10G SFP+ LC SR Transceiver (J9150A)
HPE X132 10G SFP+ LC LR Transceiver (J9151A)
HPE X132 10G SFP+ LC LRM Transceiver (J9152A)
HPE X132 10G SFP+ LC ER Transceiver (J9153A)
HPE X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable (J9281B)
HPE X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (J9283B)
HPE X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable (J9285B)
HPE X244 10G XFP to SFP+ 1m Direct Attach Copper Cable (J9300A)
HPE X244 10G XFP to SFP+ 3m Direct Attach Copper Cable (J9301A)
HPE X244 10G XFP to SFP+ 5m Direct Attach Copper Cable (J9302A)
Aruba 2530-24G-PoE+-2SFP+ Switch (J9854A)
HPE X132 10G SFP+ LC SR Transceiver (J9150A)
HPE X132 10G SFP+ LC LR Transceiver (J9151A)
HPE X132 10G SFP+ LC LRM Transceiver (J9152A)
HPE X132 10G SFP+ LC ER Transceiver (J9153A)
HPE X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable (J9281B)
HPE X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (J9283B)
HPE X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable (J9285B)
HPE X244 10G XFP to SFP+ 1m Direct Attach Copper Cable (J9300A)
HPE X244 10G XFP to SFP+ 3m Direct Attach Copper Cable (J9301A)
HPE X244 10G XFP to SFP+ 5m Direct Attach Copper Cable (J9302A)
Data sheet
Aruba 2530 Switch Series accessories (continued)
Aruba 2530-48G-2SFP+ Switch (J9855A)
HPE X132 10G SFP+ LC SR Transceiver (J9150A)
HPE X132 10G SFP+ LC LR Transceiver (J9151A)
HPE X132 10G SFP+ LC LRM Transceiver (J9152A)
HPE X132 10G SFP+ LC ER Transceiver (J9153A)
HPE X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable (J9281B)
HPE X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (J9283B)
HPE X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable (J9285B)
HPE X244 10G XFP to SFP+ 1m Direct Attach Copper Cable (J9300A)
HPE X244 10G XFP to SFP+ 3m Direct Attach Copper Cable (J9301A)
HPE X244 10G XFP to SFP+ 5m Direct Attach Copper Cable (J9302A)
Aruba 2530-24G-2SFP+ Switch (J9856A)
HPE X132 10G SFP+ LC SR Transceiver (J9150A)
HPE X132 10G SFP+ LC LR Transceiver (J9151A)
HPE X132 10G SFP+ LC LRM Transceiver (J9152A)
HPE X132 10G SFP+ LC ER Transceiver (J9153A)
HPE X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable (J9281B)
HPE X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (J9283B)
HPE X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable (J9285B)
HPE X244 10G XFP to SFP+ 1m Direct Attach Copper Cable (J9300A)
HPE X244 10G XFP to SFP+ 3m Direct Attach Copper Cable (J9301A)
HPE X244 10G XFP to SFP+ 5m Direct Attach Copper Cable (J9302A)
Learn more at
hpe.com/networking
Products within this series have achieved
sufficient scores in each of the rated criteria
to achieve the Miercom Certified Green
distinction Award. See the Specifications
section of this series for more information.
Products within this series are IPv6 Ready
certified. See the Specifications section of
this series for more information.
Sign up for updates
Rate this document
© Copyright 2012–2016 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change
without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
sFlow is a registered trademark of InMon Corp.
4AA4-4245ENN, June 2016, Rev. 8
Download PDF
Similar pages