Delta InsightPower SNMP IPv6 for UPS

7KHSRZHUEHKLQGFRPSHWLWLYHQHVV
'HOWD,QVLJKW3RZHU
6103,3YIRU836
8VHU0DQXDO
ZZZGHOWDZZFRP
SNMP IPv6 for UPS
Save This Manual
This manual contains important instructions and warnings that you should follow during the installation, operation, storage and maintenance of this product.
Failure to heed these instructions and warnings will void the warranty.
Copyright‹2011 by Delta Electronics Inc. All Rights Reserved. All rights of this User
Manual (“Manual”), including but not limited to the contents, information, and
figures are solely owned and reserved by Delta Electronics Inc. (“Delta”). The Manual
can only be applied to the operation or the use of this product. Any disposition,
duplication, dissemination, reproduction, modification, translation, extraction, or
usage of this Manual in whole or in part is prohibited without the prior written
permission of Delta. Given that Delta will continuously improve and develop the
product, changes may be made to the information in this Manual at any time
without obligation to notify any person of such revision or changes. Delta will make
all possible efforts to secure the accuracy and the integrity of this Manual. Delta
disclaims any kinds or forms of warranty, guarantee, or undertaking, either expressly
or implicitly, including but not limited to the completeness, faultlessness, accuracy,
non-infringement, merchantability or fitness for a particular purpose of the Manual.
LL
7DEOHRI&RQWHQWV
Table of Contents
Chapter 1 : Important Safety Instructions ------------------------ 1
1-1
1-2
Warnings ------------------------------------------------- 1
Standard Compliance--------------------------------- 1
Chapter 2 : Introduction------------------------------------------------ 2
2-1
2-2
2-3
2-4
Product Description----------------------------------- 2
Features -------------------------------------------------- 2
Package Contents-------------------------------------- 3
Interface -------------------------------------------------- 4
Chapter 3 : Installation ------------------------------------------------- 6
Chapter 4 : System Configurations -------------------------------- 10
4-1
4-2
4-3
4-4
4-5
Configuring via InsightPower UPS Web ------- 10
Configuring with EzSetting ----------------------- 12
Configuring via Telnet ------------------------------ 14
Configuring through COM Port ------------------ 15
Configuring via Text Mode ------------------------ 17
Chapter 5 : InsightPower UPS Web -------------------------------- 23
5-1
Monitor ------------------------------------------------- 24
5-1-1 Information ----------------------------------------------------- 24
UPS Properties ---------------------------------------------------------- 24
Battery Parameters ----------------------------------------------------- 25
In/ Out Parameters ----------------------------------------------------- 25
Identification ------------------------------------------------------------ 26
Status Indication -------------------------------------------------------- 26
Power Module ----------------------------------------------------------- 26
5-1-2 History ------------------------------------------------------------ 27
Event Log ----------------------------------------------------------------- 27
Data Log ------------------------------------------------------------------ 28
Configure ----------------------------------------------------------------- 29
LLL
SNMP IPv6 for UPS
5-1-3 Environment ---------------------------------------------------- 29
Information -------------------------------------------------------------- 29
Configuration ------------------------------------------------------------ 30
5-2
Device --------------------------------------------------- 31
5-2-1 Management --------------------------------------------------- 31
Configure ----------------------------------------------------------------- 31
Control -------------------------------------------------------------------- 33
Weekly Schedule ------------------------------------------------------- 35
Specific Schedule ------------------------------------------------------- 35
Event Level --------------------------------------------------------------- 36
5-3
System -------------------------------------------------- 37
5-3-1 Administration ------------------------------------------------- 37
User Manager------------------------------------------------------------ 37
TCP/ IP --------------------------------------------------------------------- 38
Web ------------------------------------------------------------------------ 39
Console-------------------------------------------------------------------- 40
FTP-------------------------------------------------------------------------- 41
Time Server -------------------------------------------------------------- 42
Syslog ---------------------------------------------------------------------- 43
Batch Configuration --------------------------------------------------- 43
Upgrade------------------------------------------------------------------- 45
5-3-2 Notification ----------------------------------------------------- 45
SNMP Access------------------------------------------------------------- 45
SNMPv3 USM ------------------------------------------------------------ 46
SNMP Trap ---------------------------------------------------------------- 47
Mail Server --------------------------------------------------------------- 48
Wake On LAN ------------------------------------------------------------ 49
Chapter 6 : SNMP Device Firmware Upgrade------------------- 50
Chapter 7 : Troubleshooting ---------------------------------------- 53
Appendix A : Specifications ----------------------------------------- 59
Appendix B : Warranty ------------------------------------------------ 60
LY
Chapter 1
,PSRUWDQW6DIHW\,QVWUXFWLRQV
Chapter 1 : Important Safety Instructions
1-1 Warnings
z
The InsightPower SNMP IPv6 for UPS, hereafter referred to as SNMP IPv6, is
designed to work with a UPS and needs to be installed inside the UPS’s SNMP
slot or inside an external SNMP box. Before installation, ensure that all power
sources and critical loads connected to the UPS are disconnected.
z
Do not place or use this unit in the presence of flammable substances.
z
Do not attempt to disassemble the unit.
z
Do not attempt to perform any internal modifications on the unit.
z
Do not attempt to fix/ replace internal components. When repair is needed,
refer all servicing to the nearest Delta service center or authorized distributor.
z
Do not allow any objects or liquids of any kind to penetrate the unit.
z
Always follow this User Manual to install and operate this unit.
z
Do not play the included CD on a conventional CD player. This could generate
loud noise at a level that could result in permanent hearing loss.
1-2 Standard Compliance
z
EN 55022: 2006 + A1: 2007, Class B
EN 61000-3-3: 1995+A1: 2001+A2: 2005
z
EN 55024: 1998 + A1: 2001 + A2: 2003
IEC 61000-4-2: 1995+A1: 1998+A2: 2000
IEC 61000-4-3: 2006
IEC 61000-4-4: 2004
IEC 61000-4-5: 2005
IEC 61000-4-6: 2007
IEC 61000-4-8: 1993+A1: 2000
IEC 61000-4-11: 2004
SNMP IPv6 for UPS
Chapter 2 : Introduction
2-1 Product Description
The InsightPower SNMP IPv6 for UPS is a device that provides an interface between
an UPS and a network. It communicates with the UPS, acquires its information and
remotely manages the UPS via a network system. The SNMP IPv6 supports public
protocols including SNMP and HTTP. You can effortlessly configure this SNMP IPv6
using a network system and easily obtain your UPS’s status and manage your UPS
via the SNMP IPv6.
2-2 Features
z
Network UPS management
Allows remote management of the UPS from any workstation through Internet
or Intranet.
z
Remote UPS monitoring via SNMP & HTTP
Allows remote monitoring of the UPS using SNMP NMS, Delta MIB (Management
Information Base) or a Web Browser.
z
UPS and system function configuration from any client
(password protected)
Sets the UPS and system parameters through a Web Browser.
z
Event logs & metering data keeping
Provides a history data of the UPS’s power events, power quality, status and
battery conditions.
Other features and supported protocols include:
z
User notification via SNMP Traps and e-mail
z
Network Time Protocol
z
Telnet configuration
z
BOOTP/ DHCP
Chapter 2
z
HTTPS, SSH, SFTP and SNMPv3 security protocols
z
RADIUS (Remote Authentication Dial In User Service) login and local
authentication
z
Remote event log management through syslog
z
IPv4 and IPv6
,QWURGXFWLRQ
2-3 Package Contents
Please carefully verify the SNMP IPv6 and the included accessories. Contact your
dealer if any item is missing or damaged. Should you return the items for any reason, ensure that they are carefully repacked using the original packing materials
came with the unit.
No.
Item
Quantity
InsightPower SNMP IPv6 for UPS
1 PC
RJ45 to DB9 cable
1 PC
Software & User’s Manual CD
1 PC
Cover
3 PCS
SNMP IPv6 for UPS
2-4 Interface
The interface includes NETWORK port, COM port, NET LED, UPS LED, RESET button
and dip switch shown below. For their functions and indications, please refer to the
table below.
Top view:
Network Port
LED Indicators
Console (COM) Port
Reset Button
Dip Switch
Front view:
Network Port
21
No. Item
Console
(COM) Port
Reset Button
Description
Network
Port
Connects to the Ethernet Network.
Console
(COM)
Port
1. Connects to a workstation with the provided RJ45 to DB9
cable to configure the system.
Reset
Button
Resets the SNMP IPv6. This does not affect the operation of the
UPS.
LED Indicators
Dip Switch
2. Connects to an EnviroProbe to monitor the connected
environment monitoring devices.
Chapter 2
No. Item
,QWURGXFWLRQ
Description
LED
NET LED (Green) indicates network communication status. UPS
Indicators LED (Yellow) indicates UPS communication status.
NET LED (Green)
UPS LED (Yellow)
Description
OFF
---
Hardware or
network errors
---
Blinks every second
UPS disconnection
Without EnviroProbe
ON
Blinks every 50 ms
Normal operation
With EnviroProbe
DIP
Switch
Blinks every 50 ms
Blinks every 50 ms
Normal operation
ON
Blinks every 50 ms
EnviroProbe
disconnection
Sets up operation mode.
Dip 1 Dip 2
Operation
Mode
Description
OFF
OFF
The SNMP IPv6 works with the UPS. It
Normal Mode provides the UPS’s status information and
parameters through a network system.
OFF
ON
The SNMP IPv6 stops polling the UPS but
Pass Through
transfers the communication data between
Mode
the console port and the UPS.
ON
OFF
Sensor Mode
(with
EnviroProbe)
ON
ON
In this mode, the user can login through
Configuration the console port and configure the SNMP
Mode
IPv6’s settings. Please refer to 4-4 Configuring through COM Port.
The SNMP IPv6 works with the UPS and an
optional EnviroProbe. It provides the UPS’s
information and the environmental parameters (temperature, humidity, etc).
127(
For EnviroProbe information, please refer to the Installation Guide included
in the package of the EnviroProbe.
SNMP IPv6 for UPS
Chapter 3 : Installation
127(
Before installation, please disconnect all power sources and critical loads connected to the UPS. Otherwise, the SNMP IPv6 might have shorting issues to
cause UPS shutdown or damage.
Please install the SNMP IPv6 inside your UPS’s SNMP slot. If your UPS does not have
any SNMP slot, please install it in an optional external SNMP box.
z
Please follow the procedures below to install the SNMP IPv6 into your UPS’s
SNMP slot.
Step 1
Remove the cover and the two screws shown from the UPS’s SNMP
slot (see Figure 3-a).
Figure 3-a
UPS
SNMP slot
127(
Please note that, due to different design, the location of screws
for each UPS’s SNMP slot might be different.
Step 2
Find the two grooves inside the SNMP slot (see Figure 3-b).
Figure 3-b
Two grooves
Chapter 3
Step 3
,QVWDOODWLRQ
Insert the SNMP IPv6 into the grooves (see Figure 3-c).
Figure 3-c
Two grooves
Step 4
There are three covers provided in the SNMP IPv6’s package. Please
follow the location of screw holes on the SNMP slot to select the suitable cover, and use the two screws that you just removed to fix the
cover on the SNMP slot (see Figure 3-d).
Figure 3-d
z
Please follow the procedures below to install the SNMP IPv6 into an external
SNMP box.
Step 1
Remove the two screws shown from the external SNMP box (see Figure 3-e).
Figure 3-e
External SNMP box
SNMP slot
SNMP IPv6 for UPS
Step 2
Find the two grooves inside the external SNMP box (see Figure 3-f).
Figure 3-f
Two grooves
Step 3
Insert the SNMP IPv6 into the grooves (see Figure 3-g).
Figure 3-g
Two grooves
Step 4
There are three covers provided in the SNMP IPv6’s package. Please
follow the location of screw holes on the external SNMP box to select
the suitable cover, and use the two screws that you just removed to
fix the cover on the external SNMP box (see Figure 3-h).
Figure 3-h
Chapter 3
,QVWDOODWLRQ
127(
The backside view of the external SNMP box is shown as follows.
Power Jack
No. Item
RS232 Port
10-pin Connector
Description
Power Jack
Connects your UPS’s output. The input power
should be 12Vdc.
RS232 Port
Use the RS232 cable provided by your UPS to
connect your UPS’s RS232 port.
10-pin
Connector
Connects your UPS’s PC board. Please ask qualified service personnel to execute such connection. Do not perform the connection yourself.
Please refer to the table below for the external SNMP box’s specifications.
External SNMP Box Specifications
Power Jack
Input Power 12Vdc
RS232 Port
D-Sub 9-Pin Male
10-pin Connector
Male
Size (W×D×H)
92.4 x 208 x 42 mm
Weight
540 g
SNMP IPv6 for UPS
Chapter 4 : System Configurations
There are different ways you can configure your InsightPower SNMP IPv6. If a network connection is available at your location, the following methods can be used.
z
Web-based InsightPower UPS Web (please refer to Chapter 5: InsightPower
UPS Web). This offers complete system management and monitoring.
z
Provided program EzSetting (Please refer to 4-2 Configuring with EzSetting)
z
Telnet mode (please refer to 4-3 Configuring via Telnet)
The above-mentioned methods require network connection. If it is not available at
your location, you can use direct COM port connection to set up your InsightPower
SNMP IPv6. Please see 4-4 Configuring through COM Port.
127(
1. To ensure system security, it is highly recommended that you change your
account and password after the first login.
2. If you have other SNMP IPv6 units connected in your network, we highly
suggest that you change the SNMP IPv6’s default Host Name to avoid Host
Name conflicts. Also, it is recommended that you disable BOOTP/ DHCP
and manually assign a valid static IP address for the SNMP IPv6.
4-1 Configuring via InsightPower UPS Web
To set up the SNMP IPv6 via the InsightPower UPS Web, please see the following
instructions:
Step 1
Use a CAT5 cable to connect the SNMP IPv6’s network port and the network. Launch your Web Browser and enter default Host Name InsightPower or the SNMP IPv6’s default IP 192.168.1.100 in the address box. If
you are unable to connect, please see Chapter 7: Troubleshooting Q6.
Chapter 4
6\VWHP&RQ¿JXUDWLRQV
127(
If you have previously changed the SNMP IPv6’s Host Name or IP address,
make sure to provide the correct information accordingly.
Step 2
Log in as Administrator (default account/ password: admin/ password,
case sensitive). Click SystemȻAdministrationȻUser Manager. Manage your login accounts and passwords under the “Local Authentication”
subhead. The access permission for the account types are listed as follows:
1) Administrator: Permitted to modify all settings.
2) Device Manager: Permitted to modify device-related settings.
3) Read Only User: Only permitted to observe monitoring data.
127(
You can manually specify whether users are allowed to log in from external
connections (from other LANs). Selecting Only in This LAN will block login
attempts from external connections. Selecting Allow Any will allow these
attempts.
Step 3
Click SystemȻAdministrationȻTCP/ IP to set Host Name, IP address,
Subnet Mask and Gateway IP for the SNMP IPv6.
Step 4
Click Time Server to manually set time and date for the system, or enable
automatic time synchronization between the SNMP IPv6 and the time
servers.
127(
To configure all InsightPower SNMP IPv6’s settings including system information, input/ output management, system administration, event notifications and event history, please refer to Chapter 5: InsightPower UPS Web –
5-1 Monitor, 5-2 Device, 5-3 System.
SNMP IPv6 for UPS
4-2 Configuring with EzSetting
One of the easiest ways to configure the SNMP IPv6 is utilizing EzSetting (Compatible with Windows systems), a program you can find in the provided CD. You can
use it to set up your InsightPower SNMP IPv6 and perform firmware upgrades on
your SNMP devices.
Step 1
Set up a workstation (Windows 2000/ 2003/ 2008/ XP/ Vista/ Win7 or later
version).
Step 2
Use a CAT5 cable to connect the SNMP IPv6’s network port and the network.
Step 3
Make sure both of the DIP switches of the SNMP IPv6 are set to the OFF
position (normal mode) to enable network transmission, and make sure
the workstation and the SNMP IPv6 are on the same LAN.
Step 4
Insert the provided CD in the CD-ROM drive. From the root directory,
launch EzSetting.
Step 5
Click Discover to search all SNMP devices on the LAN. A list of devices
will be shown.
Chapter 4
6\VWHP&RQ¿JXUDWLRQV
127(
1. If you want to search all SNMP devices in a different domain, change the
Subnet and IPv4/ IPv6 Prefix Length and then click Discover.
2. If the SNMP IPv6 can not be found, check the networking port UDP 3456
on the workstation you are using. Make sure it is not blocked.
Step 6
Select a device from the Device List, click Modify, and key in Administrator account and password. Default account/ password: admin/ password
(case sensitive).
Step 7
Click Configuration and set up essential parameters.
SNMP IPv6 for UPS
127(
To configure all InsightPower SNMP IPv6’s settings including system
information, input/ output management, system administration, event notifications and event history, please refer to Chapter 5: InsightPower UPS
Web.
4-3 Configuring via Telnet
Step 1
Use a CAT5 cable to connect the SNMP IPv6’s network port and the network.
Step 2
Set up a workstation (Microsoft Windows, Max OSX or Linux). Connect
the workstation to the same LAN which the SNMP IPv6 is connected to.
Step 3
Make sure both of the DIP switches of the SNMP IPv6 are set to the OFF
position (normal mode).
Step 4
For Windows workstations, launch DOS prompt mode (StartȻRun
Ȼkey in cmd and press Enter). For Linux, launch shell.
Step 5
Enter the following command: telnet InsightPower to initiate telnet connection with the SNMP IPv6.
Step 6
When connection is established, enter account and password (default:
admin/ password, case sensitive). The Main Menu will appear on the
screen. Please refer to 4-5 Configuring via Text Mode for more information.
127(
1. The SNMP IPv6 will terminate idle connections after 60 seconds.
2. To configure all InsightPower SNMP IPv6’s settings including system
information, input/ output management, system administration, event
notifications and event history, please refer to Chapter 5: InsightPower
UPS Web.
Chapter 4
6\VWHP&RQ¿JXUDWLRQV
4-4 Configuring through COM Port
If network connection is not available at your location, you can still manage the
SNMP IPv6 by using the COM port connection. Please follow the instructions below.
127(
If you are running on a non-Windows system, refer to your system’s User
Manual for Telnet clients.
Step 1
Set up a workstation (Microsoft Windows 2000, 2003, 2008, XP, Vista or 7).
Step 2
Use the provided RJ45 to D89 cable to connect the SNMP IPv6’s COM port
and the workstations’ COM port.
Step 3
Make sure both of the DIP switches of the SNMP IPv6 are set to the OFF
position (normal mode).
Step 4
For workstations running Windows 2000, 2003, 2008 or XP, go to StartȻ
ProgramsȻAccessoriesȻCommunications and select HyperTerminal.
127(
Microsoft has removed HyperTerminal from Windows Vista and later
versions. For workstations running these systems, you can still download a
free Telnet/ SSH client ‘PuTTY’ from http://www.putty.org.
SNMP IPv6 for UPS
Step 5
Enter a name and choose an icon for the connection. Click OK to continue. From the dropdown list Connect using, select the COM port that
is connected to the SNMP IPv6.
Step 6
Click Configure and set up COM port parameters as follows:
Step 7
Click OK to continue and set both of the DIP switches of the SNMP IPv6
to the ON position (configuration mode). HyperTerminal will automatically connect to the SNMP IPv6. If it does not connect, click the telephone
icon call from the icon list. When connection is established, log in with
account/ password. (Default: admin/ password, case sensitive). Once you
are logged in, the Main Menu appears on the screen. Please refer to 4-5
Configuring via Text Mode for more information.
Chapter 4
6\VWHP&RQ¿JXUDWLRQV
4-5 Configuring via Text Mode
You can configure the SNMP IPv6 via text mode by using Telnet/ SSH clients such
as HyperTerminal and PuTTy. In this section, you can find descriptions and default
values for each item in the table.
Main Menu
0DLQ0HQX
__
:HE&DUG9HUVLRQ
0$&$GGUHVVDEHH
>@8VHU0DQDJHU
>@7&3,36HWWLQJ
>@1HWZRUN3DUDPHWHU
>@7LPH6HUYHU
>@6RIW5HVWDUW
>@5HVHW$OO7R'HIDXOW
>]@([LW:LWKRXW6DYH
>@6DYH$QG([LW
3OHDVH(QWHU<RXU&KRLFH !
User Manager
8VHU0DQDJHU
__
5$',86
>@5$',86$XWK'LVDEOH
>@6HUYHU
>@6HFUHW
>@3RUW
/RFDO$XWK
$GPLQLVWUDWRU
>@$FFRXQWDGPLQ
>@3DVVZRUG
>@/LPLWDWLRQ2QO\LQ7KLV/$1
'HYLFH0DQDJHU
>@$FFRXQWGHYLFH
>@3DVVZRUG
>D@/LPLWDWLRQ2QO\LQ7KLV/$1
5HDG2QO\8VHU
>E@$FFRXQWXVHU
>F@3DVVZRUG
>G@/LPLWDWLRQ$OORZ$Q\
>@%DFN7R3UHYLRXV0HQX
3OHDVH(QWHU<RXU&KRLFH !
SNMP IPv6 for UPS
No.
Item
Description
[1]
RADIUS Auth
Specify whether RADIUS login is alDisable
lowed
[2]
Server
The RADIUS server name
[3]
Secret
The RADIUS secret
[4]
Port
The RADIUS port number
[5]
Administrator
Account
[6]
Administrator
Password
[7]
Administrator
Limitation
[8]
Device Manager
Account
[9]
Device Manager
Password
The default account/ password (case device
sensitive) for the Device Manager who
is only permitted to change devicepassword
related settings
[a]
Device Manager
Limitation
Restrict login area of the Device Man- Only in
ager
This LAN
[b]
Read Only
User Account
[c]
Read Only
User Password
[d]
Read Only
User Limitation
The default account/ password for the
Administrator (case sensitive)
Restrict Administrator login area
Default
1812
admin
password
Only in
This LAN
The default account/ password (case user
sensitive) for Read Only User who can
only observe settings
password
Restrict login area of the Read Only
Allow Any
User
Chapter 4
6\VWHP&RQ¿JXUDWLRQV
TCP/IP Setting
7&3,36HWWLQJ
__
>@,3Y$GGUHVV
>@,3Y6XEQHW0DVN
>@,3Y*DWHZD\,3
>@,3Y'16RU:,16,3
>@'+&3Y&OLHQW(QDEOH
>@,3Y$GGUHVVIHDEIIIH
>@,3Y3UHIL[/HQJWK
>@,3Y*DWHZD\,3
>@,3Y'16,3
>D@'+&3Y(QDEOH
>E@+RVW1DPH1HW%,26,16,*+732:(5
>F@6\VWHP&RQWDFW
>G@6\VWHP/RFDWLRQ
>H@$XWR1HJRWLDWLRQ(QDEOH
>I@6SHHG0
>J@'XSOH[)XOO
>K@6WDWXV6WDEOH
>@%DFN7R3UHYLRXV0HQX
3OHDVH(QWHU<RXU&KRLFH !
No.
Item
Description
Default
[1]
IPv4 Address
The IPv4 address
192.168.001.100
[2]
IPv4 Subnet
Mask
The IPv4 subnet mask setting
255.255.255.000
[3]
IPv4 Gateway IP The IPv4 network gateway
192.168.001.254
[4]
IPv4 DNS or
WINS IP
IPv4 Domain Name Server or
WINS IP
192.168.001.001
[5]
DHCPv4 Client
Enable/ Disable DHCPv4 protocol
Enable
[6]
IPv6 Address
The IPv6 address
[7]
IPv6 Prefix
Length
The IPv6 prefix length
[8]
IPv6 Gateway IP The IPv6 network default
gateway
[9]
IPv6 DNS IP
IPv6 Domain Name Server IP
address
[a]
DHCPv6
Enable/ Disable DHCPv6 protocol
Enable
SNMP IPv6 for UPS
No.
Item
Description
[b]
Host Name
(NetBIOS)
The Host Name for the SNMP IPv6 INSIGHTPOWER
[c]
System
Contactor
The System Contactor information
[d]
System
Location
The System Location information
[e]
Auto-Negotia- Enable/ Disable automatic trans- Enable
tion
fer rate (10/ 100M bps) negotiation
[f ]
Speed
If the Auto-Negotiation is dis- 100M
abled, you can specify the transfer rate
[g]
Duplex
If the Auto-Negotiation is dis- Full
abled, you can specify the duplex
mode
[h]
Status Stable
Status change confirmation check 3
time
Network Parameter
1HWZRUN3DUDPHWHU
__
>@+7736HUYHU(QDEOH
>@+77366HUYHU(QDEOH
>@7HOQHW6HUYHU(QDEOH
>@66+6)736HUYHU(QDEOH
>@)736HUYHU'LVDEOH
>@6\VORJ'LVDEOH
>@+7736HUYHU3RUW
>@+77366HUYHU3RUW
>@7HOQHW6HUYHU3RUW
>D@66+6HUYHU3RUW
>E@)736HUYHU3RUW
>F@6\VORJ6HUYHU
>G@6\VORJ6HUYHU
>H@6\VORJ6HUYHU
>I@6\VORJ6HUYHU
>J@6103*HW6HW3RUW
>@%DFN7R3UHYLRXV0HQX
3OHDVH(QWHU<RXU&KRLFH !
Default
Chapter 4
6\VWHP&RQ¿JXUDWLRQV
No.
Item
Description
Default
[1]
HTTP Server
Enable/ Disable HTTP protocol
Enable
[2]
HTTPS Server
Enable/ Disable HTTPS protocol
Enable
[3]
Telnet Server
Enable/ Disable Telnet protocol
Enable
[4]
SSH/ SFTP Server
Enable/ Disable SSH/ SFTP protocol
Enable
[5]
FTP Server
Enable/ Disable FTP protocol
Disable
[6]
Syslog
Enable/ Disable remote syslog
Disable
[7]
HTTP Server Port
HTTP networking port
80
[8]
HTTPS Server Port
HTTPS networking port
443
[9]
Telnet Server Port
Telnet networking port
23
[a]
SSH Server Port
SSH networking port
22
[b]
FTP Server Port
FTP networking port
21
[c]
Syslog Server1
The remote syslog Host Name
[d]
Syslog Server2
The remote syslog Host Name
[e]
Syslog Server3
The remote syslog Host Name
[f ]
Syslog Server4
The remote syslog Host Name
[g]
SNMP Get, Set Port
The SNMP networking port
161
Time Server
You can manually adjust time and date for the SNMP IPv6 or set up automatic
time server synchronization. The SNMP IPv6, Windows XP and later versions
work with SNTP (Simple Network Time Protocol). If you need to start up a time
server service on your workstation, please refer to Chapter 7: Troubleshooting
Q1.
7LPH6HUYHU
__
>@7LPH6HOHFWLRQ6173
>@7LPH=RQHKU
>@VW7LPH6HUYHU322/17325*
>@QG7LPH6HUYHU
>@0DQXDO'DWH00''<<<<
>@0DQXDO7LPHKKPPVV
>@%DFN7R3UHYLRXV0HQX
3OHDVH(QWHU<RXU&KRLFH !
SNMP IPv6 for UPS
No.
Item
Description
Default
[1]
Time Selection
SNTP or manual
SNTP
[2]
Time Zone
[3]
Select the time zone
+0 hr
st
The first time server for SNTP
POOL.NTP.ORG
nd
1 Time Server
[4]
2 Time Server
The second time server for SNTP
[5]
Manual Date
Set the date manually
01/01/2000
[6]
Manual Time
Set the time manually
00:00:00
Soft Restart
Reset the SNMP IPv6. This will not affect the operation of the UPS.
Default Reset
Reset to manufacture default.
Exit Without Saving
Exit and ignore changes.
Save and Exit
Preserve your changes and exit.
Chapter 5
,QVLJKW3RZHU836:HE
Chapter 5 : InsightPower UPS Web
To configure the SNMP IPv6 via the InsightPower UPS Web, please follow the steps
below:
Step 1
Make sure that your InsightPower SNMP IPv6 is connected to the LAN. Use
a CAT5 cable to connect the SNMP IPv6’s network port and the network.
Step 2
Launch your Web Browser. Enter the SNMP IPv6’s Host Name http:/InsightPower/ or IP address http://192.168.1.100/ in the address bar.
For encrypted connection, enter https://InsightPower/ or https://192.
168.1.100/.
Step 3
When connection is established, the InsightPower UPS Login page appears. Enter your account and password. (Default: admin/ password).
http://192.168.1.100/
127(
1. If you have previously changed the SNMP IPv6’s Host Name or IP address,
make sure to provide the correct information accordingly.
2. If the login page is accessible, but you are unable to log in with correct
account and password, additional network configuration is needed. The
cause could be the IP subnet of the computer you are logging in to is different from the SNMP IPv6’s. To solve this issue, please refer to Chapter 7:
Troubleshooting Q3.
3. The SNMP IPv6 will automatically log off idle connections after 30 minutes.
SNMP IPv6 for UPS
The InsightPower UPS Web includes the information of Monitor, Device and
System. Please refer to the following sections 5-1~5-3 for more information.
5-1 Monitor
Under the Monitor category, there are Information, History and Environment these
three items.
5-1-1 Information
This includes the information of UPS Properties, Battery Parameters, In/ Out Parameters, Identification, Status Indication, and Power Module. Please note that since
different UPSs provide different information, the UPS that you have may not display
the same web page.
UPS Properties
Go to MonitorȻInformation ȻUPS Properties to see a status overview of
the UPS’s major parameters. The values will be updated automatically.
http://192.168.1.100/
Chapter 5
,QVLJKW3RZHU836:HE
Battery Parameters
Go to MonitorȻInformationȻBattery Parameters to view the information
of Battery Status, Battery Measurement, Battery Cabinet and Replacement Date.
http://192.168.1.100/
In/ Out Parameters
Go to MonitorȻInformationȻIn/ Out Parameters to view the information
of Input Measurement, Bypass Measurement and Output Measurement.
http://192.168.1.100/
SNMP IPv6 for UPS
Identification
Go to MonitorȻInformationȻIdentification to view the information of
Identification and UPS Rating.
http://192.168.1.100/
Status Indication
Go to MonitorȻInformationȻStatus Indication to view the UPS’s event
list. When an event occurs, its according beacon lights green.
http://192.168.1.100/
Power Module
Go to MonitorȻInformationȻPower Module to view the information
of Power Module Bypass and Power Module ID1/ 2/ 3/ 4. Please note that this
page only appears when your UPS has designated power modules.
Chapter 5
,QVLJKW3RZHU836:HE
http://192.168.1.100/
5-1-2 History
Event Log
Go to MonitorȻHistoryȻEvent LogȻPage 1/ 2/ 3/ 4 to see events that
occur. The existing ones are overwritten when the maximum number of entries
(1,000) is reached. You can also download the entire event log archive (event_
log.xls) recorded during an assigned period of time on your computer.
http://192.168.1.100/
SNMP IPv6 for UPS
z
Date: The date when the event occurred.
z
Time: The time when the event occurred.
z
Level: The Event Level of the event occurred.
z
Event Log: The description of the event that occurred.
z
Download Event Log from UPS
The SNMP IPv6 sends a request to the UPS, collects the event logs saved in
the UPS, and replies to the user through network. Please note that this option only appears when the UPS supports this function, and the event logs
saved in the UPS may be different from the event logs saved in the SNMP
IPv6.
Data Log
Go to MonitorȻHistoryȻData Log to see all saved device data. You can
also download the data archive (data_log.xls) recorded during an assigned period of time on your computer.
http://192.168.1.100/
z
Date: The date when the data entry is recorded.
z
Time: The time when the data entry is recorded.
Chapter 5
,QVLJKW3RZHU836:HE
Configure
Go to MonitorȻHistoryȻConfigure to clear the history data logs and
event logs. You can also assign the Save Data Interval.
http://192.168.1.100/
z
Clear History Data: Empty history data logs.
z
Clear Event Log: Empty event logs.
z
Save Data Interval: The time interval after which an event/ data entry is
recorded.
5-1-3 Environment
Information
Go to MonitorȻEnvironmentȻInformation to see the information of Sensor, Input Contacts and Contact Setting.
http://192.168.1.100/
SNMP IPv6 for UPS
Configuration
Go to MonitorȻEnvironmentȻConfiguration to configure the Warning
Threshold, Alarm Threshold, Title and Type. Please note that you can use the
two dip switches to set different operation modes. Please see the table below
for detail information.
http://192.168.1.100/
Dip 1 Dip 2
Description
OFF
OFF
Normal Mode
The SNMP IPv6 works with the UPS. It provides the
UPS’s status information and parameters through
a network system.
OFF
ON
Pass Through
Mode
The SNMP IPv6 stops polling the UPS but transfers
the communication data between the console
port and the UPS.
OFF
Sensor Mode
(with
EnviroProbe)
The SNMP IPv6 works with the UPS and an optional EnviroProbe. It provides the UPS’s information
and the environmental parameters (temperature,
humidity, etc).
ON
Configuration
Mode
In this mode, the user can login through the console port and configure the SNMP IPv6’s settings.
Please refer to 4-4 Configuring through COM
Port.
ON
ON
Opeation
Mode
Chapter 5
,QVLJKW3RZHU836:HE
5-2 Device
5-2-1 Management
Since different UPSs have different functions, your UPS may not support the same
configurations or control items stated below.
Configure
Go to DeviceȻManagementȻConfigure to configure the UPS. The configuration values are saved in the UPS or in the SNMP IPv6 and these values
change UPS operation. The configuration items include the following. Please
note that different UPSs may support different configuration options.
http://192.168.1.100/
z
Auto Restart
After you click Submit to confirm your auto restart setup, the SNMP IPv6
will send the command to the UPS to enable auto restart.
z
UPS Buzzer
After you click Submit to confirm your buzzer setup, the SNMP IPv6 will
send the command to the UPS to enable buzzer.
z
Voltage Sensitivity
After you set up your voltage sensitivity (there are Normal, Reduced, and
Low selections) and click Submit, the SNMP IPv6 will send the command to
the UPS to enable the UPS’s voltage sensitivity function.
SNMP IPv6 for UPS
z
Transfer Voltage
After you click Submit to confirm your transfer voltage setup, the SNMP
IPv6 will send the command to the UPS to enable the relevant functions.
z
Low Battery
This configuration saves the setup values in the SNMP IPv6 and compares
with the values received from the UPS. If the received battery level is lower
than the assigned one, the SNMP IPv6 will trigger a low-battery alarm.
z
UPS Shutdown Action
This configuration saves your setup values in the SNMP IPv6 and compares
with the values received from the UPS. If an event like power failure or low
battery occurs, the SNMP IPv6 will send the assigned shutdown delay command to the UPS.
z
Smart Shutdown
The Smart Shutdown configuration is used to safely shutdown all of the
connected computers and the UPS. First of all, you should estimate the longest OS Shutdown Delay time for your operating systems that have been installed shutdown software and connected to the SNMP IPv6. The SNMP IPv6
will delay the assigned OS Shutdown Delay time and wait for all operating
systems’ shutdown. After that, the SNMP IPv6 will send the assigned UPS
shutdown-delay command to the UPS and turn off the UPS.
z
Battery Replacement Date
After you set up battery replacement dates, the SNMP IPv6 will send the
command to the UPS and save the information in the UPS.
z
External Battery Pack
After you click Submit to confirm your external battery pack setup, the
SNMP IPv6 will send the command to the UPS and save the external battery
pack quantity in the UPS.
z
Bypass Transfer Frequency
After you set a tolerance of bypass transfer frequency and confirm your setup, the SNMP IPv6 will send the command to the UPS. If the UPS transfers to
bypass mode and the bypass frequency is out of the tolerance, output will
be turned off and critical loads will be protected.
Chapter 5
z
,QVLJKW3RZHU836:HE
Bypass Transfer Voltage
After you set a tolerance of bypass transfer voltage and confirm your setup,
the SNMP IPv6 will send the command to the UPS. If the UPS transfers to
bypass mode and the bypass voltage is out of the tolerance, output will be
turned off and critical loads will be protected.
z
Periodic Auto Test
This configuration is used to set up battery test time. After you confirm your
setup, the SNMP IPv6 will send the command to the UPS and save the setup
in the UPS. When the test time is due, the UPS will automatically perform
the battery test.
z
Output Dry Contacts
After you click Submit to confirm your setup of output dry contacts, the
SNMP IPv6 will send the command to the UPS, save the values in the UPS,
and report the current UPS’s status.
Control
Go to DeviceȻManagementȻControl to configure relevant control commands. After you click Submit, the SNMP IPv6 will send the according commands to the UPS to enable relevant functions. The control items include the
following.
http://192.168.1.100/
SNMP IPv6 for UPS
z
Battery Test
After you select the battery test type and click Submit, the SNMP IPv6 will
send the command to the UPS to enable the battery test accordingly.
z
Shutdown & Restart UPS Only
After you confirm your setup, the SNMP IPv6 will send the command to the
UPS to shut down or/ and restart the UPS.
If you want to shutdown the UPS, please check the UPS Shutdown Delay
box and key in delay time.
If you want to restart the UPS, please check the UPS Restart Delay box and
key in delay time.
If you want to shutdown and restart the UPS, please check both of the boxes and key in according delay time.
z
Smart Shutdown
The Smart Shutdown configuration is used to safely shutdown all of the
connected computers and the UPS. First of all, you should estimate the longest OS Shutdown Delay time for your operating systems that have been installed shutdown software and connected to the SNMP IPv6. The SNMP IPv6
will delay the assigned OS Shutdown Delay time and wait for all operating
systems’ shutdown. After that, the SNMP IPv6 will send the assigned UPS
shutdown-delay command to the UPS and turn off the UPS.
z
Outlet Control
Press the Switch Bank button to control the UPS output relay (on or off ).
z
Power Fail/ Restore Simulation
Click Power Fail Test or Power Restore Test button to let the SNMP IPv6
simulate UPS power failure or power restore event. This function allows you
to test all of the connected software and verify whether they work properly
or not. Please note that the simulation won’t influence UPS operation, the
UPS remains in its original operation mode and won’t transfer to battery
mode.
Chapter 5
,QVLJKW3RZHU836:HE
Weekly Schedule
Go to DeviceȻManagementȻWeekly Schedule to arrange a weekly schedule for the UPS. You can select No Action, Shutdown, Restart, 10-Second Test,
and set up what day and what time you want the action to be executed.
http://192.168.1.100/
Specific Schedule
Go to DeviceȻManagementȻSpecific Schedule to arrange a specific schedule for the UPS. You can set up a specific date (MM/ DD/ YYYY) and time (hh:mm)
for a specific action (Stop Action, Shutdown, Restart, 10-Second Test).
http://192.168.1.100/
SNMP IPv6 for UPS
Event Level
Go to DeviceȻManagementȻEvent Level to set up a level for an event.
If you want to receive an event notification, please refer to 5-3-2 Notification SNMP Trap and 5-3-2 Notification - Mail Server.
http://192.168.1.100/
Chapter 5
,QVLJKW3RZHU836:HE
5-3 System
Under the System category, there are Administration and Notification these two
items.
5-3-1 Administration
User Manager
The SNMP IPv6 supports RADIUS. Check the Use RADIUS box, key in required
information including Server, Secret and Port (default: 1812) and click Submit
to enable RADIUS. You can define service types for Administrator, Device Manager and Read Only User. If RADIUS is disabled, you can still manage the Account Name, Password and Login Limitation for Local Authentication.
http://192.168.1.100/
SNMP IPv6 for UPS
TCP/ IP
This allows Administrator to configure local network parameters for the SNMP
IPv6.
http://192.168.1.100/
z
TCP/ IP Settings for IPv4
1) DHCP Client: Enable/ Disable DHCP. If enabled, DHCP server automatically assigns an IP address to the SNMP IPv6.
2) IP Address: The IP address in dotted format (e.g. 192.168.1.100).
3) Subnet Mask: The Subnet Mask for your network (e.g. 255.255.255.0).
4) Gateway IP: The IP address for network gateway in dotted format (e.g.
192.168.1.254).
5) DNS IP: The IP address Domain Name Server in dotted format (e.g.
192.168.1.1).
6) Search Domain: If the Host Name you provided cannot be found, the
system appends the search domain to your Host Name.
z
TCP/ IP Settings for IPv6
1) DHCP Client: Enable/ Disable DHCP. If enabled, DHCP server automatically assigns an IP address to the SNMP IPv6.
Chapter 5
,QVLJKW3RZHU836:HE
2) IP Address: The IPv6 address.
3) Prefix Length: The prefix length for the IPv6 address.
4) Gateway V6IP: The IP address for the IPv6 network gateway.
5) DNS V6IP: The IP address for the IPv6 domain name server.
z
System
1) Host Name: The SNMP IPv6 Host Name on the network.
2) System Contact: System contactor information.
3) System Location: System location information.
z
Link
1) Auto-Negotiation: Enable/ Disable automatic transfer rate (10/ 100M
bps) negotiation.
2) Speed: If the Auto-Negotiation is disabled, you can specify the transfer
rate.
3) Duplex: If the Auto-Negotiation is disabled, you can specify the duplex
mode.
Web
This allows Administrator to enable/ disable HTTP/ HTTPS communication protocols.
http://192.168.1.100/
SNMP IPv6 for UPS
z
Web
1) HTTP: Enable/ disable HTTP connection.
2) HTTPS: Enable/ disable HTTPS connection.
3) HTTP Port: Assign an HTTP port number (default: 80).
4) HTTPS Port: Assign an HTTPS port number (default: 443).
5) Web Refresh Period: Web refresh update interval.
z
SSL Certificate
1) To ensure connection security between the SNMP IPv6 and the connecting workstation, SSL certificate can be used to encrypt and secure
the integrity of transmitting data.
2) Certificate File: This allows you to replace your own SSL certificate file.
The SNMP IPv6 supports PEM format which is generated by OpenSSL.
Click Choose File to upload a certificate file.
127(
For more information regarding generating a private SSL certificate file,
please refer to Chapter 7: Troubleshooting Q12, or visit http://www.
openssl.org/.
Console
This menu allows the Administrator to enable or disable Telnet/ SSH communication protocols.
http://192.168.1.100/
Chapter 5
,QVLJKW3RZHU836:HE
z
Telnet: Enable/ disable Telnet connection.
z
SSH/ SFTP: Enable/ disable SSH/ SFTP connection.
z
Telnet Port: Assign a Telnet port number (default: 23).
z
SSH Port: Assign an SSH protocol port number (default: 22).
z
Host Key:
DSA/ RSA Key: This allows you to replace your own SSH keys. The SNMP
IPv6 supports key files generated by OpenSSH. Please refer to Chapter 7:
Troubleshooting Q13.
FTP
This allows Administrator to enable/ disable FTP communication protocol.
http://192.168.1.100/
z
FTP: Enable/ disable FTP connection.
z
FTP Port: Assign an FTP port number (default: 21).
SNMP IPv6 for UPS
Time Server
You can manually set the time and date, or allow automatic time synchronization with SNTP servers. Please note that if the SNTP server is not responsive, the
event and data log will not register even when SNTP is enabled.
http://192.168.1.100/
z
Simple Network Time Server
1) Time Zone: From the dropdown menu, select the time zone for the location where the SNMP IPv6 is located.
2) Primary/ Secondary Time Server: Two time servers can be added. Every 60 minutes, the SNMP IPv6 synchronizes with the first responding
server.
3) Enable Daylight Saving: Check to enable daylight saving time. During
this period, the SNMP IPv6 adjusts time forward one hour.
z
Manual
If a time server is not accessible, you can still manually set time and date.
Please note that every time you restart the SNMP IPv6’s network module,
time and date is reinstated to previous assigned settings.
Chapter 5
,QVLJKW3RZHU836:HE
Syslog
Syslog is used to store event logs on remote syslog servers. This will not affect
the local event logs.
http://192.168.1.100/
Batch Configuration
The SNMP IPv6 provides batch configuration to allow quick and effortless setup
on multiple SNMP devices. You can duplicate settings by exporting configuration files from the SNMP IPv6 that you have successfully configured, and import
the configuration files on other devices.
http://192.168.1.100/
SNMP IPv6 for UPS
z
System Configuration
The System Configuration includes settings saved in the Management
and Administration tabs. To download a configuration file, simply click
Download. To upload a configuration file, click Choose File, select the file
you wish to upload, and click Upload.
127(
If the IP address is static and you wish to copy settings to other devices
on the same LAN, you must manually remove the following line IP=xxx.
xxx.xxx.xxx under the [System] section from the exported configuration file. You can open the configuration file with text editors such as
Notepad and WordPad. To modify/ assign IP address for the SNMP IPv6,
please see Chapter 4: System Configurations.
z
SNMP Configuration
The SNMP Configuration includes settings in the Notification tab. To download a configuration file, simply click Download. To upload a configuration
file, click Choose File, select the file you wish to upload, and click Upload.
127(
If you need to modify the command lines, please do not delete the unmodified ones. They should be left intact to assure the integrity of the
configuration file.
Chapter 5
,QVLJKW3RZHU836:HE
Upgrade
This menu allows the Administrator to update the SNMP IPv6’s firmware.
http://192.168.1.100/
5-3-2 Notification
SNMP Access
http://192.168.1.100/
SNMP IPv6 for UPS
The SNMP IPv6 supports SNMP protocol and SNMP NMS (Network Management System), which are commonly used to monitor network devices for conditions that call for administrative attention. To prevent unauthorized access, you
can specify the NMS IP addresses that are allowed to access, their community
strings and access levels. The maximum number of IP entries is 256.
127(
If IP address 0.0.0.0 is enlisted, the NMS IP access restriction is ignored.
The SNMP IPv6 checks the community string to identify the access level
and permission according to your setting.
SNMPv3 USM
SNMPv3 offers features such as the encryption of packets and authentication to
improve security. The SNMPv3 USM (User Session Management) allows you to
assign eight User Names whose access is granted via SNMPv3 protocol. You can
also define their respective Security Levels, Auth Passwords, Priv Passwords and
Access Levels.
http://192.168.1.100/
Chapter 5
,QVLJKW3RZHU836:HE
SNMP Trap
SNMP Trap alerts users to event occurrences in your monitored environment. To
enable SNMP Trap, you must add Target IP addresses to the Target IP list. Specify
the Community String, Trap Type, MIB, SNMPv3 User Name, UDP port, and Event
Level, and click Add. If you wish to update or delete a Target IP address, specify
the IP address in the Target IP list, and click Update or Delete.
http://192.168.1.100/
127(
The SNMP IPv6 provides SNMPv1, v2c and v3 traps to satisfy most of
customers’ environments. If you use the SNMPv3 trap, please provide
one of the user names in the SNMPv3 USM table.
You can determine what event notifications should be sent to the Target
IP(s) from Event Level. Three Event Levels are listed as follows:
z Information: All event notifications are sent to the target address.
z Warning:
Both Warning and Alarm event notifications are sent to
the target address.
z Alarm: Only Alarm event notifications are sent to the target address.
You can go to DeviceȻManagementȻEvent Level to change the
event level.
SNMP IPv6 for UPS
Mail Server
You can set up an SMTP Server and specify a list of E-mail recipients who will receive notifications when events occur. The maximum number of recipients is 256.
http://192.168.1.100/
127(
If a DNS server is not available in the network, you need to manually assign an SMTP server address to enable the E-mail notification system.
z
SMTP Server Name or IP
If a Host Name is entered, a DNS IP should be added in TCP/ IP. Please see
5-3-1 Administration – TCP/ IP.
z
Account
The mail server login account.
z
Password
The mail server login password.
z
Receiver
The recipients’ E-mail addresses.
Chapter 5
z
,QVLJKW3RZHU836:HE
Event Level
Select the Event Level that when triggered, an E-mail notification is sent to
the corresponding recipient.
1) Information: All event notifications are sent to the target address.
2) Warning: Warning and Alarm event notifications are sent to the target
address.
3) Alarm: Only Alarm event notifications are to the target address.
Wake On LAN
Wake On LAN function can start up clients’ PCs from network with MAC address,
and you can set up at maximum 256 MAC addresses. The configuration can wake
up clients’ PCs after power restores or the SNMP IPv6 starts up.
http://192.168.1.100/
SNMP IPv6 for UPS
Chapter 6 : SNMP Device Firmware Upgrade
With the provided program EzSetting, you can effortlessly perform a firmware upgrade for SNMP devices discoverable on the LAN. Please refer to the following instructions to upgrade your devices.
Step 1
The subnet mask allows you to refine the device discovery range in the
specified subnets. Make sure the SNMP device you wish to upgrade is in
the subnet that is specified. If it is not, please modify the subnet and subnet mask.
Chapter 6
6103'HYLFH)LUPZDUH8SJUDGH
Step 2
Click Discover. A list of SNMP devices on the specified subnet is shown.
Step 3
Select a device from the Device List, click Modify, and key in Administrator account and password.
SNMP IPv6 for UPS
Step 4
Click Upgrade. The upgrade dialog box pops up. Click Browse to select
a valid SNMP IPv6 firmware binary file. Verify the firmware version listed
under File Information, and then click Upgrade Now to continue.
Step 5
The upgrade process should take about 20 seconds.
Step 6
When the upgrade is completed, the following dialog box appears. It
takes about 1 minute for the device to reboot.
Chapter 7
7URXEOHVKRRWLQJ
Chapter 7 : Troubleshooting
Q1. How to set up a SNTP server on my workstation for the SNMP IPv6 to synchronize?
To enable SNTP services in Windows XP, go to StartȻControl PanelȻAdd/
Remove ProgramsȻAdd/ Remove Windows ComponentsȻNetworking
ServicesȻcheck Simple TCP/ IP ServicesȻOK. To enable time synchronization, you need to set SNTP time server addresses in Time Server. Please refer
to Chapter 4: System Configurations.
Q2. How to make sure that network connection is established between my
workstation and the SNMP IPv6?
To check connection between the SNMP IPv6 and workstation, in Windows
please launch DOS prompt mode (StartȻRunȻkey in cmd and press Enter). In Linux, launch Shell. Enter the following command: ping Host Name
(default: InsightPower). If the connection is correctly established, you should
be able to receive replies from the SNMP IPv6.
&?!SLQJ
3LQJLQJZLWKE\WHVRIGDWD
5HSO\IURPE\WHV WLPH PV77/
5HSO\IURPE\WHV WLPH PV77/
5HSO\IURPE\WHV WLPH PV77/
5HSO\IURPE\WHV WLPH PV77/
3LQJVWDWLVWLFVIRU
3DFNHWV6HQW 5HFHLYHG /RVW ORVV
$SSUR[LPDWHURXQGWULSWLPHVLQPLOOLVHFRQGV
0LQLPXP PV0D[LPXP PV$YHUDJH PV
&?!
Q3. I can access the login page, but cannot log in the InsightPower UPS Web.
Please check the IP addresses of the SNMP IPv6 and the workstation you are
trying to log in. The cause could be they are not connected to the same LAN.
In that case, launch EzSetting and change User Limitation settings to Allow
Any. Please see the following figure.
SNMP IPv6 for UPS
Q4. How to refresh the NetBIOS table in Windows Systems?
If you assign a new static IP address to the SNMP IPv6, you may need to refresh
the NetBIOS table so that it corresponds with the new one. Although Windows
updates its NetBIOS table periodically, you can still manually force it to refresh
by entering the following command nbtstat –R in DOS prompt mode or shell.
After that, you can now connect to the SNMP IPv6 by its Host Name.
Q5. How to obtain the IP address and MAC address from my workstation?
For Windows, please enter ipconfig /all in DOS prompt mode. For UNIX, please
enter ifconfig in shell. You should be able to check your IP and MAC (Physical
Address) now.
3K\VLFDO$GGUHVV'$$&
'+&3(QDEOHG<HV
$XWRFRQILJXUDWLRQ(QDEOHG<HV
/LQNORFDO,3Y$GGUHVVIHDGEEFHIF3UHIHUUHG
,3Y$GGUHVV3UHIHUUHG
6XEQHW0DVN
&?!
Chapter 7
7URXEOHVKRRWLQJ
Q6. Unable to ping or connect to the SNMP IPv6?
Check connection by following the measures below.
1) Ensure that your workstation and the SNMP IPv6 are on the same LAN.
2) You can connect to the SNMP IPv6 only when the IP addresses of your
workstation and the SNMP IPv6 are from the same address block. Normally,
private LANs use IP Addresses from one of the following blocks:
10.0.0.0~10.255.255.255
172.16.0.0~172.31.255.255
192.168.0.0~192.168.255.255
The default IP address (192.168.1.100) for the SNMP IPv6 is on the 192.168.1.1~
192.168.1.254 block. If your workstation’s IP is on a different address block, you
will not be able to connect to the SNMP IPv6. To solve this problem, you can
either:
1) Use the COM port connection to change the SNMP IPv6’s IP address. Please
see 4-4 Configuring through COM port.
2) Change the workstation’s IP address so that they are on the same block.
(192.168.1.0~192.168.1.255)
Q7. Unable to perform an SNMP Get operation?
Check the SNMP settings of the SNMP IPv6. Please see 5-3-2 Notification. Make
sure that the workstation’s IP address is added on the NMS IP list with Read or
Read/ Write access. The community string on the PC and the SNMP IPv6 must
match.
Q8. Unable to perform an SNMP Set operation?
Check the SNMP settings of the SNMP IPv6. Please see 5-3-2 Notification. Make
sure that the workstation’s IP address is added on the NMS IP list, with Read/
Write permission. The community string on the PC and the SNMP IPv6 must
match.
Q9. Unable to receive SNMP traps?
Check the SNMP Trap settings of the SNMP IPv6. Please see 5-3-2 Notification.
Make sure that the workstation’s IP address is added on the Target IP list.
SNMP IPv6 for UPS
Q10. Forgot Administrator account and password?
To reset account and password, connect the RJ45 to DB9 serial cable to the
console port. Start Text Mode (Please refer to 4-4 Configuring through COM
Port), when the login information is prompted, key in rstadmin within 30 seconds and then press enter. The Administrator account and password are now
reset to default (admin/ password).
Q11. How to enable IPv6 on the SNMP IPv6?
If you are operating in Windows XP, please enable IPv6 first (click STARTȻ
RUN, and enter ipv6 install). The SNMP IPv6 supports IPv6, therefore, no additional configuration is required. However, please note that IPv6 is automatically
disabled if an identical LLA (Local-link Address) already exists in the LAN. Also,
when the IPv4 and IPv6 settings coexist, IPv4 is used as the primary IP address
for the SNMP IPv6.
To learn more information regarding IPv6 compatibility, please visit IETF (http://
tools.ietf.org/html), or IPv6 Ready Logo Program (http://www.ipv6ready.org).
Q12. How to generate a private SSL (Secure Socket Layer) certificate file (in PEM
format) for HTTP connection?
To ensure connection security between the SNMP IPv6 and your browser, you
can create your own SSL certificate file on Linux. Please download and install
OpenSSL from http://www.openssl.org. Launch shell and enter the following
command to create your own certificate file:
2SHQVVO UHT ±[ ±QRGHV ±GD\V ±QHZNH\
UVD±NH\RXWFHUWSHP±RXWFHUWSHP
1) Answer the prompted questions. Proceed as directed by the messages.
Once it is completed, a file named cert.pem is created in the current working directory.
2) Upload cert.pem on the InsightPower UPS Web. Please refer to 5-3-1 Administration – Web.
Q13. How to generate DSA and RSA keys for SSH?
For Linux:
1) Please download and install OpenSSH from http://www.openssh.org.
Chapter 7
7URXEOHVKRRWLQJ
2) Launch shell and enter the following command to create your own keys:
Please ignore it when prompted to provide passphrase.
'6$.H\VVKNH\JHQ±WGVD
56$.H\VVKNH\JHQ±WUVD
3) Upload DSA and RSA key files on the InsightPower UPS Web. Please refer to
5-3-1 Administration – Console for more information.
For Windows:
1) Please download and install PuTTY from http://www.putty.org.
2) Run puttygen.exe from the installed directory.
3) Select SSH-2 RSA from the Parameters area and click KeyȻGenerate
key pair to generate a RSA key.
4) Select ConversionsȻExport OpenSSH Key and assign a file name to the
RSA key. Please ignore it when prompted to provide key passphrase.
5) Select SSH-2 DSA from the Parameters area and select KeyȻGenerate
key pair to generate a DSA key.
6) Select Export OpenSSH Key from Conversions and assign a file name to
the DSA key. Please ignore it when prompted to provide key passphrase.
7) Upload the DSA and RSA key files to the InsightPower UPS Web. Please refer to 5-3-1 Administration – Console for more information.
Q14. How to test SNMPv3 in Linux?
Before you can access the SNMP OID (Object Identifier) via SNMPv3 protocol,
the SNMPv3 USM table must be organized. Please refer to 5-3-2 Notification –
SNMPv3 USM for more information.
To test SNMPv3 in Linux, launch shell and key in the following command:
VQPSZDON Y X XVHU! O DXWK3ULY $ SDVV
ZRUG! ; SDVVZRUG! Q FRQWH[W QDPH! W LS!
-v: 1 for SNMPv1, 3 for SNMPv3.
-l: Follow the security levels. They are: noAuthNoPriv, authNoPriv and authPriv.
-u: The user name which is assigned from SNMPv3 USM table.
SNMP IPv6 for UPS
-A: The Auth Password which is assigned from SNMPv3 USM table.
-X: The Priv Password which is assigned from SNMPv3 USM table.
-n: The Context Name which is assigned from SNMPv3 USM table.
-t: Timeout in seconds.
<ip>: The IP address of the SNMP IPv6.
<oid>: The next available SNMP OID (for example: 1.3.6.1.2.1.1.1.0). Please refer
to the RFC1213 MIB.
Appendix A
6SHFL¿FDWLRQV
Appendix A : Specifications
Model Name
InsightPower SNMP IPv6
Power Input
12 Vdc
Power Consumption
2 Watt (Max.)
Network Connection
RJ-45 jack connector (10/ 100M)
Physical
Size (W x D )
130 mm x 60 mm
Weight
75 g
Environmental
Operating Temperature
0 ~ 60濎
Storage Temperature
-40 ~ 125濎
Operating Humidity
0 ~ 90 % (Non-condensing)
127(
* Refer to the rating label for the safety rating.
* All specifications are subject to change without prior notice.
SNMP IPv6 for UPS
Appendix B : Warranty
Seller warrants this product, if used in accordance with all applicable instructions,
to be free from original defects in material and workmanship within the warranty
period. If the product has any failure problem within the warranty period, Seller will
repair or replace the product at its sole discretion according to the failure situation.
This warranty does not apply to normal wear or to damage resulting from improper
installation, operation, usage, maintenance or irresistible force (i.e. war, fire, natural
disaster, etc.), and this warranty also expressly excludes all incidental and consequential damages.
Maintenance service for a fee is provided for any damage out of the warranty period.
If any maintenance is required, please directly contact the supplier or Seller.
WARNING : The individual user should take care to determine prior to
use whether the environment and the load characteristic are suitable,
adequate or safe for the installation and the usage of this product. The
User Manual must be carefully followed. Seller makes no representation or warranty as to the suitability or fitness of this product for any
specific application.
NO.UMEN3915100924-S35111129
Download PDF
Similar pages