Extenders of LAN 100Base-Tx over UTP Cat5e
LAN-EXT-PD/NPD
Mounting to flat surface*
Mounting to DIN35*
▪ 100 BASE-TX Ethernet extension
▪ PoE/PoE+ supply extension
▪ LAN ports overvoltage protections 30A 8/20µs
▪ ESD protection acc. to IEC 61000-4-2 ±15kV
▪ Compatible with PoE acc. to IEEE 802.3af & at
▪ Working temperature – 40°C to +70°C
IP65
ORDERING NAME
CODE
SUPPLY
LAN-EXT-PD
2-106-572
PoE/24-60VDC/20-30VAC
LAN-EXT-NPD
2-107-572
PoE/24-60VDC/20-30VAC
LAN-EXT-NPD-IP65
2-107-573
only PoE
*Holders for mounting are included.
Figure 1: LAN-EXT-PD/NPD - connection to switches without PoE
Max. 100m
switch
Max. 100m
LAN-EXT
Power Supply:
Power Supply
24-60VDC/20-30VAC
Ethernet 100Base-Tx
Figure 2: LAN-EXT-PD - connection to switches with PoE
POE-PSE
POE-PD
Max. 100m
switch
LAN-EXT
Max. 100m
Power Supply
PoE
Ethernet 100Base-Tx
Figure 3: LAN-EXT-NPD/IP65 - connection to switches with PoE
POE-PSE
Max. 100m
switch
LAN-EXT
PoE
POE-PD
Max. 100m
PoE
Ethernet 100Base-Tx
POE-PSE
Max. 100m
switch
Max. 100m
LAN-EXT
LAN-EXT
PoE
PoE
Ethernet 100Base-Tx
www.metel.eu
Max. 100m
1/6
PoE
POE-PD
Installation manual REV:201411
LAN-EXT-PD/NPD
Extenders of LAN 100BASE-TX over UTP Cat5e
LAN-EXT-PD - Description and technical parameters
LAN-EXT-BOX-PD is a LAN network extender designed for extension of LAN by 100m. When using LAN-EXT throughput of 100Mbps
in full duplex is guaranteed throughout the whole transmission length. PoE-PD (Power DEvice acc. to IEEE 802.3af
and IEEE 802.3at) is a circuit included with the extender and it supports standard detection and classification mechanisms acc. to
IEEE 802.3af and IEEE 802.3at. When supplying from standard PoE injector or switch it is necessary to keep to the rule given by the
standard, i.e PoE-PSE circuit in the switch / injector can supply only one PoE PD device (extender). See figure 2 on the previous
page.
LAN-EXT-NPD/IP65 - Description and technical parameters
LAN-EXT-BOX-NPD is a PoE and LAN network extender designed for extension of LAN by 100m. In case of using 2 extenders LAN can
be extended up to 300m. When using LAN-EXT throughput of 100Mbps in full duplex is guaranteed throughout the whole
transmission length. After connection of switch / injector with PoE support acc. to IEEE 802.3af or IEEE 802.3at the extender waits
for the moment when the terminal PoE PD device (camera, sensor) is detected and classified. Only thens it’s switched on and starts
data transmission. See figure 3 on the previous page.
LAN-EXT-NPD-IP65 is to perform in outdoor box with IP65 cover.
Note: LAN-EXT-NPD-IP65 can be powered only via PoE, you can not use a separate external power supply.
Ethernet
Power Supply
Parameter
Value
Unit
Note
100 Base-Tx
2x RJ45
Yellow LED ACT
Activity detection
Green LED LINK
10/100Mbps speed detection
Overvoltage protection
30
A
8/20 μs
Contact Discharge: ±8
kV
IEC 61000-4-2
Contact Discharge: ±15
kV
IEC 61000-4-2
EFT Protection: 60
A
IEC 61000-4-4
PoE
IEEE 802.3af / IEEE 802.3at
DC
24-60
VDC
VAC
AC
20-30
Power consumption
Max. 1.5W
Yellow LED PWR
Detection of supply connection
Protections
Overvoltage: 600W test pulse 10/1000µs
Current: reversible
Environment
Mechanical
Parameters
Operational range
–40...+70
°C
Humidity
Max. 95 (non-condensing)
%
BOX: Dimensions - w / h / l
52 / 32 / 82
mm
IP65: Dimensions - w / h / l
114 / 73 / 184
mm
Weight: BOX / IP65
0,16 / 0,36
kg
Certification
temp. of environment
TÜV
The producer retains the right to change any technical parameters without previous announcement.
Max. transmitted PoE power (Figure 3)
PoE Source Terminal PoE device in distance:
150m (1 extender)
200m (1 extender)
250m (2 extenders)
300m (2 extenders)
PoE switch
12
11
10
9
PoE+ switch
21
20
18
16
www.metel.eu
2/6
Installation manual REV:201411
LAN-EXT-PD/NPD
Extenders of LAN 100BASE-TX over UTP Cat5e
Installation LAN-EXT-PD
1. Mounting
3. Connect data cables
Mount the LAN Extender to the desired place, either to
flat surface or to DIN35 rail.
The extender has 2 fast ethernet ports supporting
100BASE-TX FULL DUPLEX speed. PORT 1 supports
PoE/PoE+ supply. One LAN Extender allows extension of
data line by max. 100m. The extension is possible only
twice to total length max. 300m from the switch/
injector.
2. Connect supply
LAN Extenders can be supplied over data cable using PoE
(IEEE 802.3af ) / PoE+ (IEEE 802.3at) standards.
Extenders can be also supplied from an external source
with voltage 24-60VDC (regardless of polarity) or 2030VAC.
LED indication
Yellow LED PWR – switching on indicates connection of
supply.
Green LED LINK – switches on after connection of a
device with 100 BASE-Tx FULL DUPLEX interface.
Yellow LED ACT – blinking indicates packets passage.
POE-PSE
PoE
100 BASE-TX
PoE
PD
20-30VAC
24-60VDC
PWR
PORT 1
PORT 2
100 BASE-TX
CODE: 2-106-572
TYPE: LAN-EXT-BOX-PD
LAN-EXT-PD
EXTERNAL
SUPPLY INPUT
www.metel.eu
3/6
POE-PD
Installation manual REV:201411
LAN-EXT-PD/NPD
Extenders of LAN 100BASE-TX over UTP Cat5e
Installation LAN-EXT-NPD/IP65
1. Mounting
3. Connect data cables
Mount the LAN Extender to the desired place, either to
flat surface or to DIN35 rail.
The extender has 2 identical fast ethernet ports
supporting 100BASE-TX FULL DUPLEX speed and
PoE/PoE+ supply. One LAN Extender allows extension of
data line by max. 100m. The extension is possible only
twice to total length max. 300m from the switch/
injector.
2. Connect supply
LAN Extenders can be supplied over data cable using PoE
(IEEE 802.3af ) / PoE+ (IEEE 802.3at) standards.
Extenders can be also supplied from an external source
with voltage 24-60VDC (regardless of polarity) or 2030VAC.
LED indication
Yellow LED PWR – switching on indicates connection of
supply.
Green LED LINK – switches on after connection of a
device with 100 BASE-Tx FULL DUPLEX interface.
Yellow LED ACT – blinking indicates packets passage.
Note: LAN-EXT-NPD-IP65 - can be powered only via PoE
(terminals for external power supply is not available).
POE-PD
POE-PSE
PoE
PoE
100 BASE-TX
PORT 1
PoEi
PORT 2
PoEi
100 BASE-TX
PWR
20-30VAC
24-60VDC
CODE: 2-107-572
TYPE: LAN-EXT-BOX-NPD
LAN-EXT-NPD
EXTERNAL
SUPPLY INPUT
www.metel.eu
4/6
Installation manual REV:201411
LAN-EXT-PD/NPD
Extenders of LAN 100BASE-TX over UTP Cat5e
Dimension LAN-EXT-NPD/PD
REVISION: 201211
REVISION: 20121117
REVISION: 201212
REVISION: 201310
REVISION: 201411
www.metel.eu
Start of production
Divided into A and B versions
Change of version names (A -> PD and B -> NPD)+
Change how supply in NPD (see note on page 2)
Add LAN-EXT-NPD-IP65
5/6
Installation manual REV:201411
LAN-EXT-PD/NPD
Extenders of LAN 100BASE-TX over UTP Cat5e
Dimension LAN-EXT-NPD-IP65
www.metel.eu
6/6
Download PDF
Similar pages