FD600CAM-3 - Flight Display Systems

Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 1 of 18
Installation and Operation Manual
FD600CAM-3
Glareshield Camera
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 2 of 18
Specifications
Video Output
Video Output Mode
Camera Sensor
Camera Lens
Camera Frame Rate
Effective Pixels
Approximate Field of View
Scanning System
Signal to Noise Ratio
Minimum Illumination
Dimensions, Camera
Dimensions, Mount
Weight
Power
Operating Temperature
© 2017 FDS Avionics Corp.
All Rights Reserved.
HD-SDI
HD-SDI: 1080p@30fps; 720p@60fps
1/3” Color CCD
F=3.6, 6mm Lens
30fps@1080p or 60fps@720p
1944(H) x 1092 (V)
75 with supplied 3.6mm Lens
45 with supplied 6mm Lens
2:1 Interlace
More than 50 dB
0.1 Lux
1.35” (W) x 1.35” (H) x 2.92” (D)
2.0” (W) x 1.75” (H) x 1.75” (D)
Approx. 6 oz.
28 Volt nominals, 18V Min / 30V Max
14 F to 122 F (-10 C to +50 C)
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 3 of 18
Table of Contents
General Information ...................................................................................................................4
Front View ..................................................................................................................................4
Installation Instructions ..........................................................................................................5
Power ...........................................................................................................................................5
Wiring Suggestions ..................................................................................................................5
Video Wiring..............................................................................................................................6
Power and Ground Wiring .................................................................................................. 6-7
Power/Video ...............................................................................................................................7
RS485 ...........................................................................................................................................8
OSD Menu............................................................................................................................ 9-10
Functions............................................................................................................................. 11-14
Technical Drawing..................................................................................................................15
Technical Support ...................................................................................................................16
Instructions for Continued Airworthiness ........................................................................16
Warranty ...................................................................................................................................17
Log of Revisions ......................................................................................................................18
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 4 of 18
General Information
The FD600CAM-3 is a Glareshield Camera. This small color camera, when mounted in
the cockpit, will provide passengers with an opportunity to observe taxi, take-off, and
landing, adding a whole new dimension to the In-Flight Entertainment experience!
Front View
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 5 of 18
Installation Instructions
All cabin entertainment equipment, such as the FD600CAM-3, should be installed on a
non-essential bus and have a dedicated circuit breaker.
Mounting from the cockpit headliner is suggested. Excessive sunlight will make the video
image hard to see. Mounting inside the cockpit and out of direct sunlight will provide a
“visor” to the camera lens.
Remember to set the camera pointing down at an approximately 60° angle, as this will
optimize the picture for take-off and landings. When looking at the image while on the
ground have the horizon 2/3 of the way up the video screen in the cabin.
Power
The FD600CAM-3 is a 28 Volt camera that requires 160mA power and can operate at 18
– 30 Volts DC.
Wiring Suggestions
Avoid routing video wiring parallel to:
•
AC wiring
•
Strobe wiring
•
DC motor supply cables
•
Inverter cabling
•
Or any other potential noise source.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 6 of 18
Video Wiring
The recommended cable for both composite and SDI is PIC 75 Ohm Coax, P/N V75268.
This is a lightweight, flexible, and low signal loss cable which meets FAA flammability
requirements of FAR 23.1359(d), FAR 25.853(a) and FAR 25.869(a)(4).
Similar aviation coaxial cable can be used from other vendors, as well. Some aircraft are
prone to AC noise - we recommend adding to the composite source a 75Ohm video
isolation transformer such as Deerfield Laboratory, Inc. Part No. 162-1
(www.deerfieldlab.com, (650) 632-4090. In most cases this should be added to the video
output of the source.
Power and Ground Wiring
The rated current of the equipment and associated voltage drop should be taken into
consideration when selecting wire gauge. The following example is based on an install
with a 28VDC power system, 1.5-amp equipment load and a total of 50 feet of wire
between the circuit breaker, monitor and ground.
Example: 22awg wire has 16.2 Ohms per 1000 feet, this equates to .81 Ohms for 50
feet. 1.5 Amp of current on .81 Ohms will drop 1.22 Volts.
Resistance of Wire Type
M22759/16-**
(** = Gauge)
Gauge (AWG)
OHMS/1000’
24
26.20
22
16.20
20
9.88
16
4.81
12
2.02
10
1.26
8
.701
Also, use short heavy gauge wire and a clean tight connection for ground. It is the
installer's responsibility to understand the product's requirements in order to install the
product in compliance with industry standards and safety.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Rev:
Document Number:
C
MAN – FD600CAM-3
Revision Date:
07/11/2017
Page 7 of 18
Power/Video
Standard Density DB-9 Receptacle (supplied)
Connector
Crimp Contacts
Pin
Number
1
2
3
4
5
6
7
8
9
P/N: M24308/2-281 or Equivalent
P/N: M39029/63-368 or Equivalent
FD600CAM-3
Description
28 VDC Input
28 VDC Return
RS-485 B
RS-485 A
N/C
N/C
N/C
N/C
N/C
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 8 of 18
RS485 Control
The FD600CAM-3 can be setup and configured through the OSD menu. This menu can be
accessed and controlled via RS485 commands.
RS485 Port Configuration: The RS-485 port at default is standard 9600 baud, no parity, 8 data
bits, 1 stop bit, and no flow control. It is standard two wires half duplex. The commands are all
ASCII human readable.
Prefix: One Character. All RS-485 remote commands must start with the “!” character.
Device ID: Three Characters. “CAM” identifies all commands directed to the FD600CAM-3.
Commands:
!CAM,En – Button East
!CAM,Wn – Button West
!CAM,Sn – Button South
!CAM,Nn – Button North
!CAM,Pn – Button Press
(n = single ASCII char 0 to 9.)
•
•
•
•
•
•
•
•
•
•
0 = Button Pulse Time 0.25 Seconds
1 = Button Pulse Time 0.50 Seconds
2 = Button Pulse Time 0.75 Seconds
3 = Button Pulse Time 1.00 Seconds
4 = Button Pulse Time 1.25 Seconds
5 = Button Pulse Time 1.50 Seconds
6 = Button Pulse Time 1.75 Seconds
7 = Button Pulse Time 2.00 Seconds
8 = Button Pulse Time 2.25 Seconds
9 = Button Pulse Time 2.50 Seconds
Note: Buttons – North, South, East and West auto repeat
Termination: One Character; ASCII CR. Each command must end with Carriage Return<CR>.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 9 of 18
OSD Menu Structure
Main
EXPOSURE
WHITE
BALANCE
WDR/BLC
DAY &
NIGHT
IMAGE
Sub Menu
BRIGHTNESS
SHUTTER
MODE
SHUTTER
SPEED
DSS
AGC MAX
INITIAL
RETURN
WB MODE
CHROMA
KELVIN
RED GAIN
BLUE GAIN
PUSH AUTO
INITIAL
RETURN
MODE
WDR LEVEL
BLC OSD
BLC X-POS
BLC Y-POS
BLC X-SIZE
BLC Y-SIZE
INITIAL
RETURN
MODE
DWELL TIME
AGC THRS
MARGIN
INITIAL
RETURN
SHARPNESS
MIRROR
FLIP
DZOOM
HLMASK
D-WDR
DNR
INITIAL
Sub Menu
0 - 20
AUTO.MANUAL
1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K, 1/1.6K, 1/2.5K, 1/5K,
1/7K, 1/10K, 1/30K.*() is for power-frequency 50Hz.
OFF, X2, X3, X4.
0-23dB
BACK, DEFAULT
BACK, EXIT
AUTO, PUSH LOCK, MANUAL, AUTO EXT
0-20
0-20
0-20
0-20
ON, OFF
BACK, DEFAULT
BACK, EXIT
ON, OFF
0-4
ON, OFF
0 - 20
0 - 20
0 - 20
0 - 20
BACK, DEFAULT
BACK, EXIT
COLOR, B/W, AUTO
3s
0-10
0-10
BACK, DEFAULT
BACK, EXIT
0-10
ON, OFF
OFF, H FLIP, V FLIP, HV FLIP
0-20X
HLMASK LEVEL: 0-20
ON, OFF
HLMASK COLOR: Black, White, Yellow, Cyan,
Green, Magenta, Red, Blue
0-4
LOW, MIDDLE, NIGH
BACK/DEFAULT
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 10 of 18
OSD Menu Structure (Cont.)
Main
Sub Menu
Sub Menu
CAM TITLE 0 - 20
LANGUAGE ENGLISH, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE
ZONE NO
0-23
MASK MODE
ON, OFF
X-POSITION
0-60
Y-POSITION
0-40
PRIVACY
ON, OFF
X-SIZE
0-40
Y-SIZE
0-40
INITIAL
BACK, DEFAULT
RETURN
BACK, EXIT
RESOLUTION
1-10
SENSITIVITY
1-10
WINDOW USE ON, OFF
WINDOW
1-10
TONE
X-POSITION
0-60
MOTION
SPECIAL
Y-POSITION
0-40
X-SIZE
0-40
Y-SIZE
0-40
INITIAL
BACK, DEFAULT
RETURN
BACK, EXIT
CAM TITLE
ON, OFF
MOTION
ON, OFF
DISPLAY
DZOOM
ON, OFF
INITIAL
BACK, DEFAULT
RETURN
BACK, EXIT
SHADING DET ON, OFF
DEFECT DET
ON, OFF
DOUT
1080P / 720P
FORMAT
SYSTEM
DOUT FPS
30, 60
CVBS
PAL, NTSC
APPLY
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 11 of 18
Function Description
SETUP
- EXPOSURE:
- WHITE ALANCE:
- WDR / BLC:
- DAY&NIGHT:
- IMAGE:
- SPECIAL:
- FACTORY DEFAULT:
- EXIT
Go sub menu for camera exposure control.
Go sub menu for camera white balance control.
Go sub menu for camera WDR or BLC action.
Control day and night settings
Go sub menu for adjust image functions.
Go sub menu for special feature control.
Reset all settings back to factory default
EXPOSURE
- BRIGHTNESS:
- SHUTTER MODE:
- SHUTTER SPEED:
- DSS:
- AGC:
Adjust image brightness value.
Select shutter speed control type.
Enable user to set up the Shutter Speed
Adjust digital slow shutter control level.
Adjust max gain level for brightness control.
WHITE BALANCE
- WB MODE:
- CHROMA:
- KELVIN:
- RED GAIN:
- BLUE GAIN:
- PUSH AUTO:
- INITIAL:
Select white balance control mode.
• AUTO: Enable user to trace the White Balance automatically in
the range of 2,300K~10,000K.
• PUSH LOCK: Enable user to fix the White Balance according to
the color temperature in environment.
• MANUAL: Enable user to sets the White Balance according to
the circumstance
• AUTO EXT: Extended auto mode for special illumination.
Enable user to set the Color Gain(0~20steps).
In the MANUAL setting of WB MODE, enable user to set the
color temperature range.
In the MANUAL setting of WB MODE, enable user to set the RED
GAIN.
In the MANUAL setting of WB MODE, enable user to set the
BLUE GAIN.
In the PUSH LOCK setting of WB MODE, enable user to fix the
White Balance in camera setting.
Enable user to reset the WHITE BALANCE menu setting.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 12 of 18
WDR/BLC
- MODE:
- WDR LEVEL:
- BLC OSD:
- BLC X-POSITION:
- BLC Y-POSITION:
- BLC X-SIZE:
- BLC Y-SIZE:
- INITIAL:
Select WDR for BLC mode.
Enable user to adjust level of WDR (Wide Dynamic Range).
Enable user to set up screen output of selected BLC zone.
Enable user to set up screen output of selected BLC zone.
Enable user to set up Horizontal start position.
Enable user to set up Vertical size.
Enable user to set up Horizontal size.
Enable user to initialize the BLC setting.
DAY&NIGHT
- DAY&NIGHT MODE:
Conversion of output image COLOR / BW depending on exterior
environment.
•
•
•
- DWELL TIME:
- INITIAL:
COLOR: Enable user to fit the output image in color.
B/W: Enable user to fit the output image in B/W.
3 AUTO: Enable user to convert to COLOR/BW automatically by
photocell
In D&N MODE AUTO, enable user to set to delay time for
changing COLOR/BW
Enable user to initialize the setting in DAY&NIGHT menu.
IMAGE
- SHARPNESS:
- MIRROR:
- FLIP:
- DZOOM (Digital Zoom):
- HLMASK:
- D-WDR:
- DNR:
- INITIAL:
Enable user to control the image sharpness.
Enable user to mirror flip the image.
Sets the Vertical flip for the display output.
Max. 20x Digital Zoom.
Suppresses or masks strong light sources.
•
•
HLMASK LEVEL: Enable user to set HLMASK Level.
HLMASK COLOR: Set the HLMASK color
In this mode, the brightness of a single image is compensated
using the gamma curve.
This function reduces noise.
Enable user to initialize the setting on IMAGE menu.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Rev:
Document Number:
C
MAN – FD600CAM-3
Revision Date:
07/11/2017
Page 13 of 18
SPECIAL
- CAM TITLE:
Enable user to choose any word in screen. (Maximum 10 letter is
available)
•
•
- LANGUAGE:
- PRIVACY:
- MOTION:
- DISPLAY:
DZOOM.
• A letter Choice from the screen using Menu key.
• Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION.
By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in
LOCATION and then get back to previous step.
Enable user to finish words choice and position by using LEFT, RIGHT KEY in
RETURN.
Enable user to set up an OSD language.
Enables privacy function.
•
•
•
•
•
•
•
•
•
ZONE NO: Enable user to set up a position from 0 to 29 area.
MASK MODE: Enable user to set up screen output of chosen position.
X-POSITION: Mask Horizontal start position.
Y-POSITION: Mask Vertical start position.
X-SIZE: Mask Horizontal width.
Y-SIZE: Mask Vertical height.
COLOR: Set the mask color.
TRANSPARENCY: Set the transparency of the mask.
INITIAL: Enable user to initialize setting of PRIVACY MENU.
Motion detection function.
•
•
•
•
•
•
•
•
•
RESOLUTION: Enable user to set up resolution
SENSITIVITY: Enable user to set up sensitivity.
WINDOW USE: Enable user to select to motion area.
WINDOW TONE: Enable user to area window tone.
X-POSITION: Window Horizontal start position.
Y-POSITION: Window Vertical start position.
X-SIZE: Window Horizontal width.
Y-SIZE: Window Vertical height.
INITIAL: Enable user to initialize setting of MOTION DETECT.
Enable user to set up a screen marking CAM TITLE, MOTION,
•
•
•
•
CAM TITLE: Enable user to set up output in fixed CAM TITLE.
MOTION: Enable user to set up output of MOTION on the screen as MOTION
ON setting.
DZOOM: Enable user to set up output DZOOM ratio.
INITIAL: Enable user to initialize of DISPLAY menu.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
- SYSTEM:
Rev:
C
Revision Date:
07/11/2017
Page 14 of 18
Go sub menu for system control & information.
•
•
•
•
•
•
FACTORY DEFAULT:
DEFECT DET: White pixel detection and compensation function.
DOUT FORMAT: Enable user to set up digital output format (720p, 1080p).
DOUT FPS: Enable user to set up digital output frame rate.
4.FREQ: Enable user to set up power-frequency (50Hz, 60Hz).
CVBS: Enable user to set up CVBS type NTSC or PAL.
APPLY: Enable user to setting of SYSTEM.
Enable user to reset all of the status as the factory default.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 15 of 18
Technical Drawing
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 16 of 18
Technical Support
hould you have any questions concerning this product or other FDS Avionics Corp.
products, please contact our Service and Support representatives at 470-239-7421.
FDS Avionics Corp.
6435 Shiloh Road
Alpharetta, GA 30005
Phone: 470-239-7400
Fax: 470-239-7439
Email: sales@FDSAvionics.com
For further product information, technical data and sample wiring diagrams, please click
on the Dealers section of our web site at www.FDSAvionics.com
Instructions for Continued Airworthiness
The FD600CAM-3 is designed not to require regular general maintenance.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Document Number:
MAN – FD600CAM-3
Rev:
C
Revision Date:
07/11/2017
Page 17 of 18
Limited Warranty
All FDS Avionics Corp. products are warranted to be free from material or manufacturing defects for a period of 24
months from the date of shipment for General Aviation customers or 12 months from the date of shipment for
Government/Special Mission customers. Any material or repair workmanship for in warranty repair service will be
specifically warranted for 90 days or the remainder of the original warranty period, whichever is longer. If the
original warranty period has expired, the 90-day repair warranty is limited to the material and workmanship
specific to the repair activity completed.
The following conditions are exclusions to warranty coverage:
1. Labor costs associated with installation, removal or reinstallation of any product.
2. Damage to or malfunction caused by any unauthorized alteration made to the product.
3. Resolving signal quality issues caused by externally generated noise introduced by aircraft electrical
systems or other components connected to any FDS product.
4. Any malfunction caused by improper installation or connection to aircraft wiring, industry standard cabin
management/inflight entertainment systems, or third party commercial equipment not specifically identified
as compatible with FDS products.
5. Any malfunction caused by installation that does not conform to precautions associated with operating
environments listed in the operating manual or consistent with industry best practices such as high
temperature, adequate ventilation, high humidity, high dust, or power surges.
6. Cosmetic damage or damage to internal components caused by installation or removal, failure to follow
installation or operating instructions, or any neglect or misuse of the product.
7. Any product that is returned for service with a broken tamper evident seal, indicating tampering or
improper handling of the product by an unauthorized person. Violation of product tamper evident seals or
modification of factory installed serial and PMA labels voids any warranty, either expressed or implied.
The FDS Technical Support team is available to provide distance troubleshooting support during business hours
(8:00am to 5:00pm EST) Monday through Friday at (470) 239-7421.
Many repair requests can be resolved through distance support and may not require return of merchandise to the
factory. If a product must be returned to the factory for repair, an RMA number will be issued as directed by the
Technical Support team and communicated by the Repair Coordinator.
Upon request by the customer, FDS may send a Service Technician onsite to repair any non-PMA products. The
travel expenses incurred to include transportation, lodging and meals along with the technician’s hourly rate shall
be payable by the customer in accordance with FDS’ applicable rates and procedures.
FDS Avionics Corp. will, upon receipt of returned merchandise, remanufacture or replace the unit at our discretion
and return the product by Ground Return Shipping. Express return shipment will be the responsibility of the
sender.
This warranty is not transferable.
Any implied warranties expire at the express limited warranty expiration date. FDS shall not be held liable for any
indirect, special, punitive, incidental or consequential damages.
Some states do not allow limitation on the length of an implied warranty. In such states, the exclusions or
limitations of this limited warranty may not apply.
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Rev:
Document Number:
C
MAN – FD600CAM-3
Revision Date:
07/11/2017
Page 18 of 18
Revision Logs
Rev
Date
Page
Description
A
03/05/2014
All
Initial Release
B
04/14/2014
8
Added RS485 Commands
C
07/11/2017
All
New Format, New Company Name, Warranty
© 2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Download PDF
Similar pages