PT-690 Technical specification 20141225

China Aerospace Telecommunications Ltd.
PT-690
690 Technical Specification V1.0
Mini Pets Tracker
Image
GPS receiver with High sensitivity
Cute and ultra-micro
ultra
plastic shell
Features
Industrial grade high stability GSM chipset
GSM 850/900/1800/1900
Summary
Mechanical
Dimension
2.95x1.34x0.28 inches (75mm
(Length*Width*Height)
Weight
34g
Shell Material
Main body: ABS+PC
x
34mm
x7mm)
Use IOS/Android APP to track
Software
Basic location data: 68 Bytes only;
only
GSM
SIM800H;
GPS
U-blox GT-1612-MT
Modules
Time
RTC Calibration
GPS is not working: Use RTC time
GPS is working: Use GPS time
Roll
Roll-Call
(Positioning)
Tracking
Positioning
and
When the server gets the command, the device will automatically upload
the real-time
real
location data.
Fixed time interval tracking(GPRS channel)
Low power alert (less than 10%)
Features
Alarm
Geo
Geo-fence
alert
Support 1 internal Geo-Fence
Geo
region
Alarm working way
1. When alarms happen, device will upload alarm information to
platform with the details, and set the relative state register to
effective and keep the status until device received the feedback
from platform except low power alert and Geo-fence alert, the state
of low power and Geo-fence
fence alert depends on the device’s
device’
status.
2. The platform server needs to verify the alert data packet.If the
device doesn't get any verification, it will stop reporting after 3
1
China Aerospace Telecommunications Ltd.
times iterative reports. And the report time interval is 60 seconds
by default.
3. If the state register of an alarm is effective, this kind of alarm can’t
be reactive again.
4. In alarm data ,there is only the state for the one which trigger (the
GPS position is the lastest information for the device).
Blind area
store and
data
Detail: When working in GPRS mode, if GPRS
disconnect and GPS works well, no matter setting
any data report way including fixed time report, the
data will store according to the time interval. When
GPRS resume connecting, these stored data will
re-arrange and automatically upload to the sever.
re-upload
Support two working mode: GPRS+SMS and SMS
only.
Working Mode
Other Features
When device is in GSM signal blind area or the
platform isn’t connected, the GPS data were stored
and not uploaded to the server as a supply report
until GSM re-connecting.(Data in blind area
report).One data packet could contain at most 20
positions.
The factory mode is GPRS+SMS dual module
communication.
Firmware Update
Via Micro-USB portor Platform(Maintenance)
Reset
Via Micro-USB port or Platform(Maintenance) to
realize Reset, the device will restart automatically.
1.The platform sends instructions to the device
which will reset all the parameters factory set except
IP/Domain, Port, APN, User name, Password,
Device ID.
Factory Reset
2.Via Micro-USB port to send reset instruction, the
device reset all the parameters( except device ID) to
factory mode.
Via Micro-USB port or Platform to send instructions
and read APN value. As below:
IP/Port(Platform Server): 54.179.149.239/6088
Domain:www.livegpslocate.com
APN setting
APN: Empty
APN Username: Empty
APN Password: Empty
2
China Aerospace Telecommunications Ltd.
Dial Way: Default Domain
Can read Device ID and the default value is device
IMEI
3 Authorized telephone number setting, default is
empty
The default fixed time interval is 600s and the
minimum uploading interval is 60s.Run as 60s if this
interval is less than 60s.
Device hardware version: Read only
Default working mode is GPRS.
GPRS+SMS and SMS only mode.
Working
parameters setting
Can
set
Low power alert on-off: on by default
Geo-Fence alert on-off: off by default
GPS trouble alert on-off: on by default
Geo-Fence: Can set by platform and read. Support 1
cycle Geo-Fence only
End-user Identifier
End-user Remarks
Maintenance
USB firmware upgrade
Alarm SMS remind
(Low power alert and Geo-Fence alert),the device will send the alert
data by SMS to the authorized SIM number. Can set maximum 3 numbers.
It has sent-successfully rule and if failed, the data will send again.
Battery life
Max
Current
Electrical
Spec
GPS
Receiver
3.7V~4.2V, 500mAh
working
~200mA
Standby Current
<5mA
Charging Current
600mA
Charge duration
~2H
Endurance time
~72H(Ten minutes a spot)
RX
quantity
50
Frequency
Channel
1.57542GHz(L1)
3
China Aerospace Telecommunications Ltd.
GSM
Reciver
RX Code
L1, C/A
Cold Start time
~40S(Outdoor)
Warm Start time
<15s(Indoor)
Hot start time
<3S(Outdoor Patio)
Positional Accuracy
15M (Typical)
Speed accuracy
0.1m/s (Typical)
Degree accuracy
0.5 Degrees (Typical)
Acquisition
sensibility
-144
Tracking sensibility
-150
Update frequency
1 Hz
GSM/GPRS
frequency
GSM850/EGSM900/DCS1800/PCS1900
Network
communication
protocol
TCP/IP
RX sensibility
-107dBm (typ.)@850/900MHz,-106dBm (typ.)@1800/1900MHz
Max output power
Class 4 (2W)@850/900MHz,Class 1 (1W)@1800/1900MHz
GPRS Class 10
GPRS data
Mobile Station Class B
Power(red)
Off: Power off or normal working
On: Charging
Quick flash(1s): Charging completed
Slow flash(8s): Low voltage
Off: Power off
GSM(blue)
On: No SIM card or no GSM network
Indicator
Quick flash(1s): Receiving or sending data
Status
Slow flash(8s): GSM registered
GPS(green)
Off: Power off
Flash: GPS located
On: GPS locating
Turn On/Off
Press and hold the On/Off button(for 3s)
Power on indication
The above three LEDs on for 2s at the same time,then work according to
their working status respectively.
4
Download PDF
Similar pages