Installation / Operating Manual
12X Day&Night MINl PTZ CAMERA
Distributed by
388057165
PRINTED IN KOREA
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use
CONTENTS
3p.
4p.
5p.
6p.
Box Contents
6p.
Preparation for installation
6p.
PTZ setup (DIP switch)
7p.
RS-485 Setting
8p.
Installation & Cable connection
9p.
5. ON SCREEN DISPLAY MENU
Motion menu
02 MIN PTZ CAMERA
CAUTION
11p.
11p.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Preset
11p.
Tour
12p.
Scan
14p.
FCC COMPLIANCE STATEMENT
Pattern
16p.
Area
18p.
Alarm
19p.
Privacy
21p.
INFORMATION-This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference a this own expense.
Dome menu
22p.
Camera menu
25p.
Clear menu
35p.
PTZ reset
35p.
6. DIMENSIONS
7. SPECIFICATIONS
8. QUICK COMMAND
36p.
37p.
38p.
WARNING-Changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
* This installation should be made by a qualified service person and should conform to all local codes.
03 MIN PTZ CAMERA
1. USER INFORMATION
2. FEATURES
3. PRECAUTIONS
4. PTZ SETTING & INSTALLATION
USER INFORMATION
The camera is a compact 12X Day&Night PTZ camera which can be applied in
any application. This camera is packaged in a rugged aluminum die-cast housing with a
built-in high speed pan/tilt mechanism , which provides faster and more coverage than
multiple fixed cameras.
This camera offers a number of advanced features and functions; OSD menu control, Preset,
Tour, Scan, and Pattern. By utilizing the 63 programmable Presets, 4-minute Pattern
auto-pan and continuous scan mode, the camera can cover a broader range.
04 MIN PTZ CAMERA
• 1/4" 613K pixels Sony Super HAD II (Double scan) CCD
• Progressive scan 612,688 pixel
• 12x Optical Zoom, Digital 32x zoom
• High Resolution 700 TV lines - HR 7 mode
• Day & Night (ICR)
• Wide Dynamic Range(512x)
• Digital Noise Reduction(2D+3D)
• Privacy Mask Function
• Endless Pan rotation (-45 ° to 90 ° Tilt angle)
• Up to 63 programmable presets
• less than ±0.1° Preset Accuracy
• 8 programmable Tours, 4 Patterns
• Alarm - Move the camera to programmed Preset position
with Alarm trigger.(Max. 2)
• 4 Scan(Programmable speed and diagonal scan)
• Programmable Privacy Masking(4 Zones)
• RS-422, RS-485 communication
• Multiple protocol (Pelco-D, Pelco-P, Wonwoo)
• Built-in Menu System for Setup of Programmable Functions
• Mechanical Auto Flip
• Programmable Zoom Speed(Optional Update tool)
• DC 12V, 1.5A
• IP64
• E-mark for Vehicle Application
PRECAUTIONS
Do not install the camera in extreme temperature conditions.
Do use the camera under conditions where temperatures are within -10°C to 50°C.
Under high temperatures, ensure proper ventilation.
Do not install or use the camera in an environment where the
humidity is high.
It can cause the image quality to be poor.
Do not install the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
Never use the camera close to a gas or oil leak.
It can cause malfunctions to occur.
Do not disassemble the camera.
There are no user-serviceable parts inside it.
Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
Do not allow direct sunlight into the camera.
It can damage CCD.
Do not expose the camera to rain or spill beverages on it.
If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode
the electronic components.
Note
If the camera is exposed to spotlight or object reflecting the strong light,
smear or blooming may occur.
Please check the power whether it satisfies the normal specification before
connecting the camera.
05 MIN PTZ CAMERA
FEATURES
PTZ SETTING & INSTALLATION
PTZ SETTING & INSTALLATION
Box Contents
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears to
have been damaged in shipment, replace it properly in its carton and notify the shipper.
Save the shipping carton and packaging material. They are the safest material in which to make future shipments
of the equipment. Keep this Installation and Operating Manual.
Camera should be installed by qualified service personnel in accordance with all local
and federal electrical and building codes. The system should be installed according to as
described
1.PTZ setup (DIP switch)
To set the camera ADDRESS and PROTOCOL, open the cap on the left side of PTZ. There are 12 DIP switches,
3 dial switches and 1 connector for the camera program update.
ⓐ (SW502) : Set the termination, Camera installation mode and Camera video format.
ⓑ (SW501) : Set the communication protocol, baud rate and protocol parity
ⓒ (SW503~505) : Set the camera address
ⓓ : Camera program update port (Need Special update tool kit)
ⓑ
78
SW502
1 2345678
901
78
23
23
456
78
901
23
901
78
SW502
SW501
78
1 234
901
23
23
78
1 2345678
901
23
901
456
1 234
SW501
ⓐ
Installation bracket
456
Manual
456
Installation cable
456
Camera
456
ⓓ
ⓒ
3- Installation bracket
Fixing screws
Alarm/Relay
connection cable
RS-485
connector
Fixing screw
for safety wire
1-loose
proof screw
ⓐ SW502
SW502
To install and use the camera, the following is required. (NOT included in box)
1) Power adaptor (DC12V, Over 2A)
The power adaptor should be DC12V and over 2A. For better image quality and lower
failure rate, min 2A or higher is required.
06 MIN PTZ CAMERA
2) BNC cable for video signal.
BNC connectors and coaxial cables are closely related with the quality of the camera image.
3) RS-485 communication cable (Twist pair)
According to the RS-485 standards, the maximum cable length is 1.2Km
Reserved
1
TERMINATION
2
INSTALLATION
3
VIDEO
FORMAT
4
-
-
ON
ON
BOTTOM
ON
PAL
ON
-
-
OFF
OFF
TOP
OFF
NTSC
OFF
1. Reserved
2. Set the RS-485 Termination
ON: RS-485
OFF: Null.
3. Select Installation mode
ON: Bottom, OFF: TOP mode
4. Select Video format
ON: PAL, OFF: NTSC
Installation mode select
<BOTTOM>
<TOP>
07 MIN PTZ CAMERA
Preparation for installation
PTZ SETTING & INSTALLATION
PTZ SETTING & INSTALLATION
RS-485 Setting
2. Installation & Cable connection
Precautions for Installation
- Ensure that the installation location can safely bear min. 4Kg and its installation fittings.
- When installing the ceiling bracket, use the supplied fixing screws or similar screw head.
- Do not drop the product during installation. Do not allow anyone to stand below the installation area.
For RS-485 communication, the first and last devices (PTZ or keyboard controller) should be terminated
for more stable data communication by setting the DIP switches. Without proper termination, there is
potential for control signal error. Total length of the cable for communication should NOT exceed 1.2Km
(twisted pair). To extend the distance, use a reliable RS-485 repeater.
STEP 1
ⓑ SW501 (Protocol select)
SW501
PARITY
1
2
BAUDRATE
3
4
5
PROTOCOL
6
7
OFF OFF
2400bps
OFF OFF OFF
WTX (WONWOO)
OFF OFF OFF
EVEN
ON
OFF
4800bps
OFF OFF
ON
WPD (PELCO-D)
OFF OFF
ON
OLD
OFF
ON
9600bps
OFF
ON
OFF
WPP (PELCO-P)
OFF
OFF
NONE
ON
ON
ON
19200bps
OFF
ON
38400bps
ON
OFF OFF
57600bps
ON
OFF
ON
STEP 2. The external cables (video cable, controller cable
and power) should be inserted into the center hole
of the bracket.
8
NONE
STEP 1. Prepare the installation accessories provided in the
camera box. The Video and RS-485 control cables,
Power adaptor(DC12V, 2A) and installation tools are
necessary to complete the installation.
For cable connection, make a hole
(Hole size 25mm~30mm) in the ceiling where you
want to install the camera.
Attach the installation bracket with the included
3 fixing screws.
STEP 2
STEP 3. Connect the external cables to included installation
cables (Video, DC12V power, RS-485 communication,
Alarm-in, and Relay-out) For more detail connection,
please see below connector description and chart.
ON
Video out
RS-485
DC12V
ⓒ SW503~SW505 (PTZ address select)
STEP 3
Alarm / Relay
SW503 : 100 digit of camera address
SW504 : 10 digit of camera address
SW505 : 1 digit of camera address
08 MIN PTZ CAMERA
* Factory default address is 001
Black
relay 2 (NO)
Brown
relay 2 (COM)
Red
relay 1 (NO)
Orange
relay 1 (COM)
Yellow
Alarm 2 (NO)
Green
Alarm 1 (NO)
Blue
Alarm (COM)
09 MIN PTZ CAMERA
Alarm and Relay
ex) If SW503=1, SW504=2, SW505=5
then, the Camera Address = 125
PTZ SETTING & INSTALLATION
STEP 4
STEP 4. Connect the camera with the provided Installation
cable. The arrow mark on the cable connector
should be facing upwards (see diagram).
After cable connection, close the cable latch.
(CAUTION) For safety reasons, the power should be
off during the installation. There is NO power
button on the camera.
On Screen Display Menu
1 Initialize
When the device is powered on, you can check the address,
version, protocol and video setting values.
INITIALIZE
ADDRESS
VERSION
VIDEO
PROTOCOL
:
:
:
:
001 <TOP>
8.02
NTSC EMC
WPD 2400,N,1
>>PAN OFFSET . . . . . . .
>>TILT OFFSET . . .
NORMAL SETTING
2 Motion Menu
MOTION MENU
The preset function is that the camera memorizes positions
of the pan/tilt and zoom. This function is a representative
function of the speed dome which can find memorized
preset positions just by selecting the preset number.
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
STEP 5
STEP 5. Connect the metal safety wire from the bracket to
the camera with the included screw.
EXIT
(NOTICE) To make cabling without ceiling hole(Side cabling),
please cut off the cabling guide of PTZ. (see picture)
< NEAR / RIGHT
MOTION >
1) Set preset.
PRESET MENU
PRESET NO
LABEL
POSIRION
FOCUS
STEP 6. Pull the cable into the ceiling hole and attach the
camera to the bracket by turning clockwise.
After mounting the camera to the bracket, fix the
camera with the supplied fixing screw.
001 UNDEFINE
PRESET 001
019.9, 005.4
AUTO
SAVE CLR BACK EXIT
< NEAR / RIGHT
PRESET NO >
- Set PRESET Number
10 MIN PTZ CAMERA
PRESET SELECT 1
P001 P002 P003 P004 P005 P006
P 0 0 7 P 0 0 8 0 0 9 0 1 0 0 11 0 1 2
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
< SEL
NEAR/MOVE
JOYSTICK >
Press NEAR key.
Select number by using joystick
and press
NEAR
key.
11 MIN PTZ CAMERA
STEP 6
:
:
:
:
Preset No. : Max. 63 positions can be stored and the each
position can be assigned as a defined preset No.
Label : Each preset can have its own label name.
Position : It displays the coordinates to position the assigned
preset.
Focus : It enables to set the camera focus for each preset
position.
On Screen Display Menu
On Screen Display Menu
- LABEL Setting
- TOUR NO
Press NEAR key.
Select character by using joystick
PRESET LABEL EDIT <001>
and press
NEAR
LABEL : PRESET 001
0
) A
L M
X Y
1
B
N
Z
2
C
O
.
<STORE
<DEL
3
D
P
/
4
E
Q
,
TELE
WIDE
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
MOVE
BACK
9
J
V
>
TOUR NO
LABEL
TOUR EDIT
(
K
W
@
JOY >
NEAR>
PRESET POSITION
: 01 DEFINE
:
T01 T02 03
07
08
SAVE CLR BACK EXIT
< NEAR / RIGHT
TOUR NO >
< SEL
Move :
Select the Tour number
- POSITION Setting
LABEL : PRESET 001
TOUR MENU
TOUR MENU
key.
Press NEAR key.
Select number by using joystick
and press
NEAR
key.
Select :
PRESET NO
LABEL
POSIRION
FOCUS
:
:
:
:
001 DEFINE
PRESET 001
019.9, 005.4
AUTO
AUTO / MANUAL / ONE SHOT
NEAR
key.
NEAR
0 1 2
) A B C
L M N O
X Y Z .
<STORE
<DEL
SAVE CLR BACK EXIT
< NEAR / RIGHT
TOUR NO >
and press
JOYSTICK >
TOUR LABEL EDIT <01>
POSITION : 019 .9, 005.4
< EXIT
FOCUS NEAR >
Press NEAR key.
Select focus by using joystick
06
LABEL
: 01 DEFINE
:
TOUR NO
LABEL
TOUR EDIT
PRESET MENU
NEAR/MOVE
05
- LABEL
TOUR MENU
- FOCUS Setting
04
3
D
P
/
4
E
Q
,
5
F
R
+
TELE
WIDE
6
G
S
-
7
H
T
=
8
I
U
<
MOVE
BACK
9
J
V
>
(
K
W
@
JOY >
NEAR>
Set the Tour Label
Move :
Select :
or
TELE
Delete :
or
WIDE
or
JOYSTICK
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Tour.
After the label is set, push the NEAR button to exit.
- TOUR EDIT
TOUR MENU
TOUR MENU
2) TOUR
The Tour function consists of several presets run by turn.
Maximum of 8 Tour functions are toured in order.
12 MIN PTZ CAMERA
MOTION MENU
EXIT
PRESET
P001
P002
P003
P004
P005
P006
P007
P008
SAVE
< SEL
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
< NEAR / RIGHT
NO
01
02
03
04
05
06
07
08
SPEED
63
63
63
63
63
63
63
63
DWELL
02
02
02
02
02
02
02
02
CLR BACK EXIT
NEAR PRESET LEFT >
Define the Preset position
a. Move to the set-up window
BACK
TOUR >
NEAR
or
P001 P002 P003 P004 P005 P006
P 0 0 7 P 0 0 8 0 0 9 0 1 0 0 11 0 1 2
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
< SEL
NEAR/MOVE
b. Move and set the position
JOYSTICK >
c. Set & Back
NEAR
13 MIN PTZ CAMERA
SAVE CLR BACK EXIT
< CHANGE UP/DN SEL NEAR >
On Screen Display Menu
On Screen Display Menu
3) Scan
- START POSITION
By using scan function, the camera moves between 2 positions if there is no PTZ command after
passing the assigned dwell time. The scan function runs and the camera moves from the position
assigned as the start point to the position assigned as the end point in CW (Clockwise) direction.
- Scan No. : Max. 4 Scans can be stored.
- Label : The each Tour can have its own label name.
- Start position : Assign the coordinate of the Scan starting
position.
- End position : Assign the coordinate of the Scan ending position.
- Move Speed : It enables to set the running speed in the each
coordinate.(1~63)
- Dwell : The Scan function runs after the dwell time without any
camera movement.
- Focus : It enables to set the camera focus.
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT
BACK
< NEAR / RIGHT
SCAN >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
SCAN START POSITION
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, --: 60
: 02
: AUTO
POSITION : 000 .0, 000 .0
< EXIT
FOCUS NEAR >
SAVE CLR BACK EXIT
< NEAR / RIGHT
START POS >
Define the Start pan position
① Select Start Pos menu
② Move and set the position
③ Go back
or
NEAR
NEAR
- SCAN NO
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 UNDEFINE
:
: XXX.X, XXX.X
: XXX.X, --: XX
: XX
: NONE
01
Select :
02
03
SCAN MENU
04
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
SAVE CLR BACK EXIT
< NEAR / RIGHT
SCAN >
Move :
- END POSITION
SCAN MENU
< SEL
or
TELE
or
Delete :
NEAR/MOVE
JOYSTICK >
or
WIDE
NEAR
- LABEL
SCAN MENU
14 MIN PTZ CAMERA
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
SAVE CLR BACK EXIT
< NEAR / RIGHT
LABEL SEL >
or
LABEL :
SCAN MENU
0
) A
L M
X Y
1
B
N
Z
<STORE
<DEL
2
C
O
.
3
D
P
/
4
E
Q
,
TELE
WIDE
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
MOVE
BACK
9
J
V
>
(
K
W
@
JOY >
NEAR>
It’s available to set the desired label, displayed on the executing screen of scan.
After the label is set, push NEAR button to go out.
② Move and set the position
③ Go back
NEAR
- SPEED
SCAN LABEL EDIT <01>
: 01 UNDEFINE
:
: XXX.X, XXX.X
: XXX.X, --: XX
: XX
: NONE
POSITION : 000 .0
< EXIT
FOCUS NEAR >
SAVE CLR BACK EXIT
< NEAR / RIGHT END POS >
Define the End pan position
① Select End Pos menu
JOYSTICK
JOYSTICK
SCAN END POSITION
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, --: 60
: 02
: AUTO
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, --: 60
: 02
: AUTO
Set the Scan speed
Increase :
TELE
or
JOYSTICK
Decrease :
WIDE
or
JOYSTICK
SAVE CLR BACK EXIT
< NEAR / RIGHT MOVE SPEED >
It adjusts the moving speed from 0~63 steps.
15 MIN PTZ CAMERA
SCAN MENU
On Screen Display Menu
On Screen Display Menu
- DWELL
- LABEL
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, --: 60
: 02
: AUTO
The Scan function runs after the dwell time without any camera
movement.
Tiime (0 ~60 sec )
Select time by using joystick
and press
NEAR
key.
SAVE CLR BACK EXIT
< NEAR / RIGHT DWELL >
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, --: 60
: 02
: AUTO
PATTERN NO
LABEL
RECORD
PLAY
LABEL :
: 01 UNDEFINE
:
0 1 2
) A B C
L M N O
X Y Z .
<STORE
<DEL
SAVE CLR BACK EXIT
< NEAR / RIGHT
LABEL SEL >
- FOCUS
SCAN MENU
PATTERN LABEL EDIT <01>
PATTERN MENU
It enables to set the camera focus.(AUTO / MANUAL / ONESHT )
Set the pattern Label
Select focus by using joystick
Move :
and press
NEAR
key.
Select :
or
TELE
or
Delete :
JOYSTICK
6
G
S
-
7
H
T
=
8
I
U
<
MOVE
BACK
9
J
V
>
(
K
W
@
JOY >
NEAR>
or
JOYSTICK
- RECORDING
PATTERN RECORD
PATTERN MENU
The pattern function memorizes user’s random moving path and zoom ratio.
Total recording time limit is 60secs and maximum 4 pattern functions are toured in order.
＊PATTERN NO : 1~4 Patterns can be stored in keyboard menu.
＊LABEL : The each pattern can have its own label name.
＊RECORD : Movement by joystick and preset movement can be
memorized in a pattern.
＊PLAY : To revive the pattern during the recorded time.
PATTERN NO
LABEL
RECORD
PLAY
: 01 DEFINE
:
<00SEC>
SAVE CLR BACK EXIT
< NEAR / RIGHT
RECORD >
EXIT : NEAR
03/60
005 .8,000 .0
Record and Save the User’s random pattern data
① Select the “Record” Menu
EXIT
TELE
WIDE
5
F
R
+
After the label set, push NEAR button to go out.
4) PATTERN
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
4
E
Q
,
It’s available to set the desired label, displayed on the executing screen of pattern.
SAVE CLR BACK EXIT
< NEAR / RIGHT FOCUS MODE >
MOTION MENU
WIDE
3
D
P
/
② Move and record the pattern
③ Set & Back
BACK
< NEAR / RIGHT
NEAR
PATTERN >
or
NEAR
- PATTERN NO
: 01 UNDEFINE
:
01
03
04
PATTERN MENU
PATTERN NO
LABEL
RECORD
PLAY
SAVE CLR BACK EXIT
< NEAR / RIGHT
PATT NO >
Select the pattern number
02
< SEL
Move :
Select :
NEAR/MOVE
: 01 DEFINE
:
<00SEC>
JOYSTICK >
SAVE CLR BACK EXIT
< NEAR / RIGHT
PLAY >
NEAR
Play back the recorded pattern data
17 MIN PTZ CAMERA
16 MIN PTZ CAMERA
PATTERN NO
LABEL
RECORD
PLAY
- PLAY
PATTERN MENU
PATTERN MENU
On Screen Display Menu
On Screen Display Menu
- START PAN POSITION
5) AREA
The area function means that it displays the area name between two programmed pan positions.
Maximun 4 area functions are toured in order.
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT
POSITION : 000 .0, 000 .0
< EXIT
FOCUS NEAR >
Define the start pan position
① Select the “START PAN POS” menu ② Move and set the position
BACK
AREA >
NEAR
- AREA NO
or
NEAR
: 01 UNDEFINE
:
: XXX.X
: XXX.X
01
03
04
< SEL
Move :
NEAR/MOVE
AREA STOP POSITION
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
SAVE CLR BACK EXIT
< NEAR / RIGHT
AREA NO >
Select the area number
02
- STOP PAN POSITION
: 01 DEFINE
:
: 000.0
: 000.0
JOYSTICK >
POSITION : 000 .0, 000 .0
< EXIT
FOCUS NEAR >
SAVE CLR BACK EXIT
< MOVE NEAR / JOYSTICK>
Select :
NEAR
Define the stop pan position
① Select the “STOP PAN POS” Menu
- LABEL
AREA LABEL EDIT <01>
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
: 01 UNDEFINE
:
: XXX.X
: XXX.X
0 1 2
) A B C
L M N O
X Y Z .
<STORE
<DEL
SAVE CLR BACK EXIT
< NEAR / RIGHT
LABEL EDIT >
3
D
P
/
4
E
Q
,
5
F
R
+
TELE
WIDE
6
G
S
-
7
H
T
=
8
I
U
<
MOVE
BACK
9
J
V
>
(
K
W
@
JOY >
NEAR>
or
or
TELE
Delete :
or
JOYSTICK
After the label set, push NEAR button to go out.
WIDE
or
JOYSTICK
③ Set & Back
NEAR
※ “Save” above setting area data to the memory.
- "Save" above setting data to the memory.
- "CLR" means above setting pattern data will not be saved and be cleared.
- "BACK" means it goes back to the previous menu.
- "EXIT" means it goes out of the MENU
6) ALARM
MOTION MENU
Set the area Label
Select :
NEAR
LABEL :
② Move and set the position
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT
< NEAR / RIGHT
BACK
ALARM >
The alarm function means that the camera moves to the programmed
preset position by the alarm trigger.
Maximum 2 alarm functions are toured in order.
＊ALARM NO : 1~2 Alarms can be stored.
＊LABEL : The each alarm can have its own label name.
＊PRESET NO : Assign the preset No. to run when alarm is triggered.
19 MIN PTZ CAMERA
AREA NO
LABEL
START PAN POS
STOP PAN POS
③ Set & Back
※Camera will move to clockwise direction only when START setting.
AREA SELECT
AREA MENU
18 MIN PTZ CAMERA
: 01 DEFINE
:
: 000.0
: 000.0
SAVE CLR BACK EXIT
< MOVE NEAR / JOYSTICK>
< NEAR / RIGHT
Move :
AREA START POSITION
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
On Screen Display Menu
On Screen Display Menu
- ALARM NO
※ “Save” above setting alarm data to the memory.
AREA MENU
ALARM NO
LABEL
PRESET NO
- "Save" above setting data to the memory.
- "CLR" means above setting pattern data will not be saved and be cleared.
- "BACK" means it goes back to the previous menu.
- "EXIT" means it goes out of the menu.
ALARM SELECT
: 01 UNDEFINE
:
: XXX.X
01
02
7) PRIVACY setting
SAVE CLR BACK EXIT
< NEAR / RIGHT
ALRAM NO >
< SEL
NEAR/MOVE
JOYSTICK >
The alarm function means that the camera moves to the programmed preset position by the alarm trigger.
Maximum 2 alarm functions are toured in order.
Select :
NEAR
- LABEL
EXIT
ALARM LABEL EDIT <01>
AREA MENU
ALARM NO
LABEL
PRESET NO
LABEL :
: 01 UNDEFINE
:
: XXX.X
0
) A
L M
X Y
1
B
N
Z
2
C
O
.
<STORE
<DEL
SAVE CLR BACK EXIT
< NEAR / RIGHT
LABEL EDIT >
Move :
Select :
or
TELE
Delete :
or
WIDE
4
E
Q
,
5
F
R
+
TELE
WIDE
6
G
S
-
7
H
T
=
8
I
U
<
MOVE
BACK
9
J
V
>
(
K
W
@
or
- PRESET NO
PRIVACY NO
POSITION
: 01 UNDEFINE
: XXX .X, XXX .X
01
SAVE CLR BACK EXIT
< NEAR / RIGHT
PRIVACY NO >
< SEL
02
03
04
NEAR/MOVE
JOYSTICK >
* Press
NEAR
key to set privacy number and press
NEAR
key again to go out the menu.
- POSITION
PRESET SELECT 1
ALARM MENU
: 01 DEFINE
:
: 001
SAVE CLR BACK EXIT
< MOVE NEAR / JOYSTICK>
20 MIN PTZ CAMERA
PRIVACY SELECT
PRIVACY MENU
JOYSTICK
JOYSTICK
< SEL
NEAR/MOVE
PRIVACY POSITION
PRIVACY MENU
P001P002P003P004P005P006
P007P008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
Define the preset position with alarm trigger
① Select the “Preset No”
② Move and set the position
or
PRIVACY >
JOY >
NEAR>
It’s available to set the desired label, displayed on the executing screen of alarm.
After the label is set, push the NEAR button to exit.
ALARM NO
LABEL
PRESET NO
BACK
< NEAR / RIGHT
- PRIVACY NO
3
D
P
/
Set the alarm label
NEAR
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
＊PRIVACY NO : To protect privacy, Max. 4 privacy can be created
on the arbitrary position to hide objects such as windows, shops
or private house. With spherical coordinates system, powerful
privacy zone masking function is possible.
＊POSITION : Adjust the mask position
JOYSTICK >
③ Set & Back
NEAR
PRIVACY NO
POSITION
: 01 DEFINE
: 000 .0, 000 .0
MASK SIZE
POSITION : 000 .0, 000 .0
< EXIT
FOCUS NEAR >
SAVE CLR BACK EXIT
< NEAR / RIGHT
PRIVACY NO >
*Adjust masking size by using
<OPEN/CLOSE>
OPEN
,
CLOSE
keys and press
NEAR
key to go out the menu.
21 MIN PTZ CAMERA
Move :
MOTION MENU
On Screen Display Menu
On Screen Display Menu
3 Dome Menu
- TIME
Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” menu.
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
TIME
FUNCTION
NUMBER
: 02MIN
: PRESET
: 01
SAVE
< NEAR / RIGHT
EXIT
< NEAR / RIGHT
DOME >
＊TIME (MIN) : The park time can be assigned
from 5 min to 60 min(5min,10min ~60min)
PARK MENU
Select ON/OFF by using joystick
Select :
NEAR
key.
BACK
PARK TIME >
- FUNCTION
: Can select one of the motion functions, Preset, Tour, Pattern
1) Set the Dome camera title
Move :
and press
or
TELE
or
Delete :
WIDE
JOYSTICK
or
TIME
FUNCTION
NUMBER
JOYSTICK
DOME MENU
and Scan.
PARK MENU
: 02MIN
: PRESET
: 01
Select ON/OFF by using joystick
and press
NEAR
key.
TITLE SET
LABEL :
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
PRESET FREEZE
: OFF
FACTORY SET
SAVE
< NEAR / RIGHT
BACK
FUNCTION >
- NUMBER
<STORE
<DEL
SAVE
BACK
EXIT
< NEAR / RIGHT
FUNCTION >
TELE
WIDE
MOVE
BACK
JOY >
NEAR>
After the label set, push NEAR button to go out.
: The number of selected motion function.
- PRESET : 01~63
- TOUR : 01~08
- SCAN :01 ~ 04
- PATTERN : 01 ~ 04
PARK MENU
TIME
FUNCTION
NUMBER
: 02MIN
: PRESET
: 01
2) POWER UP ACTION
DOME MENU
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
: OFF
PRESET FREEZE
FACTORY SET
When this function is ON, the camera memorize the latest action
and restore it from sudden power failure.
SAVE
< NEAR / RIGHT
BACK
NUMBER >
※ When MOTION is operating, PARK ACTION is not working. (without AREA and PRIVACY )
4) DISPLAY ON/OFF
3) PARK ACTION
22 MIN PTZ CAMERA
DOME MENU
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
: OFF
PRESET FREEZE
FACTORY SET
SAVE
BACK
EXIT
< NEAR / RIGHT
SUB MENU >
DISPLAY ON/OFF SET
DOME MENU
: This function enables to locate the camera to specific position
automatically if operator doesn’t operate the controller for a while.
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
: OFF
PRESET FREEZE
FACTORY SET
* ALARM < * >
TITLE
ZOOM < * > POSITION < * >
PRESET < * > ACTION < >
<*>
TOUR
<*>
SCAN
PRIVACY < * >
PATTERN < * >
<*>
AREA
SAVE
BACK
EXIT
< NEAR / RIGHT
SUB MENU >
<ON TELE
<OFF WIDE
MOVE
BACK
JOY >
NEAR>
You can select the OSD ON to shown on the screen or clear by selecting OFF in this function.
OSD ON :
TELE
OSD OFF:
WIDE
Select :
NEAR
23 MIN PTZ CAMERA
SAVE
BACK
EXIT
< NEAR / RIGHT
FUNCTION >
On Screen Display Menu
On Screen Display Menu
4 Camera Menu
5) SPEED BY ZOOM
- SPEED BY ZOOM
DOME MENU
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
: OFF
PRESET FREEZE
FACTORY SET
Pan and tilt speed can be changed depending on zoom magnification.
ON will slow down the speed of Pan/Tilt and OFF will increase the
Pan/Tilt speed.
Select ON/OFF by using joystick
and press
NEAR
key.
Camera menu is subject to be changed without prior notice to upgrade and quality increase
and we may use slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and this manual
menu is not matched.
1) ZOOM MODE
CAMERA MENU
SAVE
BACK
EXIT
< NEAR / RIGHT
FUNCTION >
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
6) PRESET FREEZE
▷
▷
▷
▷
▷
▷
▷
Zoom speed can be set and decided using of digital
zoom function.
- PRESET FREEZE
DOME MENU
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
: OFF
PRESET FREEZE
FACTORY SET
Video out for start & stop points only and during camera movement the screen
is shown paused image.
Select ON/OFF by using joystick
and press
NEAR
SAVE
BACK
EXIT
< NEAR / RIGHT ▶ ZOOM SET >
key.
- ZOOM SPEED
ZOOM MENU
ZOOM SPD : 7
D-ZOOM : ON
SAVE
BACK
EXIT
< NEAR / RIGHT
FUNCTION >
Select :
Set OFF :
7) FACTORY SET
DOME MENU
TITLE :
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM : ON
PRESET FREEZE
: OFF
FACTORY SET
ZOOM SPEED : Select from 1 step to 7 steps
USER (Standard speed)
Restore all of setting value to the factory default.
All of existing setting value would be erased.
and press
NEAR
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶ ZOOM SPD>
- D-ZOOM
ZOOM MENU
joystick
or
key.
ZOOM SPD : 7
D-ZOOM
: ON
SAVE CLR BACK EXIT
< NEAR / RIGHT
FUNCTION >
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
D-ZOOM (Digital Zoom)
- Magnification of the digital zoom can be switched On and Off.
- It is recommended that the digital zoom should be set up before the preset operation.
- As the digital zoom magnification increases, the image quality is lowered.
25 MIN PTZ CAMERA
24 MIN PTZ CAMERA
BACK
< NEAR / RIGHT ▶ D-ZOOM >
On Screen Display Menu
On Screen Display Menu
- AF MODE
2) FOCUS
In focus menu, you can set up the focus mode among Auto,
One Push or Manual.
CAMERA MENU
ZOOM MODE
▶
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
FOCUS MODE : AUTO
FOCUS SPD : 3
NEAR LIMIT : 10CM
Select :
Set OFF :
AF MODE
: NORMAL
SENSITIVITY : NORMAL
▶
SAVE
BACK
< NEAR / RIGHT ▶ FOCUS SET >
AF MODE: Set the auto focus mode
FOCUS MENU
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶AF MODE >
EXIT
- FOCUS MODE
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : 5
NEAR LIMIT : XXXX
AF MODE
: NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT ▶FOCUS MODE >
AUTO: The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode.
In the auto focusing mode, zoom key operation is not
recognized as the input of the focus key.
One Push: It will be focused in about 5 seconds after zooming,
panning, and return to MANUAL mode automatically.
This is for focusing accurately after zooming.
Manual: In the manual mode, users can adjust the camera
focus manually.
Infinity: infinity focus is the state where a lens forms an image
of an object an infinite distance away.
This corresponds to the point of focus for parallel rays.
- FOCUS SPEED
FOCUS MENU
FOCUS MODE : MANUAL
FOCUS SPD : 3
NEAR LIMIT : 10CM
AF MODE
: NORMAL
SENSITIVITY : NORMAL
- SENSITIVITY
SENSITIVITY: Set the sensitivity of focus
FOCUS MENU
FOCUS MODE
FOCUS SPD
NEAR LIMIT
AF MODE
:
:
:
:
AUTO
3
10CM
NORMAL
Select :
Set OFF :
▶
▶
Select :
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
Set OFF :
NEAR
NEAR
3) AUTO EXPOSURE
ZOOM MODE
FOCUS MODE
Set ON :
Set ON :
BACK
< NEAR / RIGHT ▶SENSITIVITY >
Set the speed for camera focusing.
NEAR
NEAR
SENSITIVITY : NORMAL
AE setting is a function adjusting shutter speed according
to subject’s brightness to get standard amount of exposed
light.
CAMERA MENU
or
or
▶
▶
▶
SAVE
BACK
< NEAR / RIGHT ▶ AE SET >
EXIT
BACK
< NEAR / RIGHT ▶FOCUS SPD >
- AE MODE
FOCUS MENU
26 MIN PTZ CAMERA
FOCUS MODE : AUTO
FOCUS SPD : 3
NEAR LIMIT
: 10CM
AF MODE
: NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT ▶NEAR LIMIT >
Set the focus distance. (1.0 CM ~ OVERINF)
Select :
Set OFF :
or
NEAR
NEAR
Set ON :
AUTO EXPO.MENU
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
: AUTO
: AUTO
: OFF
: AUTO
: AUTO
: ON
: ON
: 0dB
BACK
< NEAR / RIGHT ▶ AE MODE >
Select AUTO,MANUAL,SHUTTER or IRIS.
Select :
Set OFF :
or
NEAR
NEAR
Set ON :
27 MIN PTZ CAMERA
- NEAR LIMIT
On Screen Display Menu
On Screen Display Menu
- SHUTTER SPEED
AUTO EXPO.MENU
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
: MANUAL
: 1/50
: OFF
: AUTO
: 28dB
: ON
: ON
: 0dB
BACK
< NEAR / RIGHT ▶ SHUTTER SPD >
- AGC MODE
If you set SHUTTER in the AE MODE, you can control image
brightness by adjusting shutter speed.
NTSC : X512, X128, X64, X32, X16, X8, 1/15, 1/30, 1/60, 1/90, 1/100,
1/180, 1/250, 1/500, 1/1000, 1/1500, 1/2000, 1/5000, 1/10000,
1/20000, 1/50000, 1/100000
PAL : X512, X128, X64, X32, X16, X8, X4, 1/25, 1/50, 1/80, 1/120,
1/150, 1/250, 1/500, 1/1000, 1/1500, 1/2000, 1/5000, 1/10000,
1/20000, 1/50000, 1/100000
Select :
Set OFF :
or
NEAR
Set ON :
Select ON/ OFF in AGC MODE.
AE EXPO.MENU
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
Select :
: IRIS
: AUTO
: OFF
: 07
: 28db
: ON
: ON
: 0dB
Set OFF :
: MANUAL
: 1/50
: OFF
: AUTO
: 28dB
: ON
: ON
: 0dB
Select ON/ OFF.
Select :
Set OFF :
or
NEAR
Set ON :
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
: AUTO
: AUTO
: OFF
: AUTO
: AUTO
: ON
: ON
: 0dB
Select :
Set OFF :
Set ON :
NEAR
- EXPO.LEVEL
If you set ON in the EXPO MODE, you can control this level.
( "0" is standard (±10.5 selectable), changed by ± 1.5dB)
AE EXPO.MENU
: IRIS
: AUTO
: OFF
: 07
: 28dB
: ON
: ON
: 0dB
NEAR
Select ON/OFF
BACK
< NEAR / RIGHT ▶ EXPO. MODE >
- IRIS LEVEL
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
or
NEAR
NEAR
BACK
< NEAR / RIGHT ▶ SLOW SHT >
AUTO EXPO.MENU
Set ON :
BACK
< NEAR / RIGHT ▶ AGC MODE >
AE EXPO.MENU
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
NEAR
- EXPO. MODE
NEAR
- SLOW SHUTTER
AUTO EXPO.MENU
or
If you set IRIS in the AE MODE, you can set the IRIS level
from 00 to 17 .
Select :
Set OFF :
or
NEAR
Set ON :
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
: AUTO
: AUTO
: OFF
: AUTO
: AUTO
: ON
: ON
: 0dB
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶ EXPO. LEVEL >
NEAR
BACK
< NEAR / RIGHT ▶ IRIS LEVEL >
4) WHITE BALANCE
Set the white balance of camera.
- GAIN LEVEL
AE MODE
SHUTTER SPD
SLOWSHUTTER
IRIS LEVEL
GAIN LEVEL
AGC MODE
EXPO. MODE
EXPO. LEVEL
: IRIS
: AUTO
: OFF
: 07
: 28dB
: ON
: ON
: 0dB
BACK
< NEAR / RIGHT ▶ GAIN LEVEL >
If you set MANUAL, IRIS and SHUTTER in the AE MODE, you can
set the GAIN for brighter image from 0~30dB. (Changable by 2dB)
Select :
Set OFF :
or
NEAR
NEAR
Set ON :
White balance setting is a function revising color temperature to
resolve the problem that screen’s colors change by the color
temperature’s difference according to time.
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
▶
SAVE
BACK
< NEAR / RIGHT ▶ WB SET >
EXIT
29 MIN PTZ CAMERA
28 MIN PTZ CAMERA
AUTO EXPO.MENU
On Screen Display Menu
On Screen Display Menu
- WB MODE
6) SPECIAL
WB MODE: Set the color depend on white balance.
Select AUTO, INDOOR, OUTDOOR, ONEPUSHWB,
ATW or MANUAL.
WHITE BALANCE MENU
WB MODE : ATW
RED GAIN : xxx
BLUE GAIN: xxx
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶WB MODE SEL >
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
In the Special menu, it’s available to set SUB SP MODE,
APERTUREGAIN, FLICKERLESS, BACK LIGHT, LINE LOCK,
V PHASE, DNR LEVEL and WDR.
SAVE
BACK
EXIT
< NEAR / RIGHT ▶ SPECIAL SET >
- RED/BLUE GAIN
RED GAIN: Adjust red color level from 0~255.
(Standard level is 025)
BLUE GAIN: Adjust blue color level from 0~255.
(Standard level is 025)
WHITE BALANCE MENU
WB MODE : MANUAL
RED GAIN : 208
BLUE GAIN: 162
Select :
BACK
< NEAR / RIGHT ▶R GAIN SEL >
Set OFF :
or
NEAR
Set ON :
NEAR
- SUB SP MODE
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : OFF
SUB SP MODE : In the special menu, it’s available
to set special function of the camera
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶SUB MENU >
5) ICR MODE
DAY / NIGHT : Select from COLOR, BW or AUTO modes.
COLOR : Color mode.
B/W : BW mode.
AUTO : The camera automatically detects lighting conditions and selects the mode accordingly.
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAMERA RESET
SAVE
BACK
< NEAR / RIGHT ▶ICR SET >
SPECIAL MENU
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
ICR MENU
▶
▶
▶
▶
▶
▶
▶
- STABILIZER
ICR MODE : AUTO
ICR THRESHOLD :11
STABILIZER: Select ON or OFF.
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶ON/OFF>
EXIT
BACK
< NEAR / RIGHT ▶ICR MODE >
- HLC MODE
ICR MENU
ICR MODE : AUTO
30 MIN PTZ CAMERA
ICR THRESHOLD :11
Set the ICR THRESHOLD from 00 to 28 .
Select :
Set OFF :
BACK
< NEAR / RIGHT ▶DAY LEVEL >
or
NEAR
Set ON :
SPECIAL MENU
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
NEAR
BACK
< NEAR / RIGHT ▶ MODE>
HLC MODE : Select ON or OFF.
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
31 MIN PTZ CAMERA
- ICR THRESHOLD
On Screen Display Menu
On Screen Display Menu
- BACK LIGHT
- HLC CLIP LEVEL
SPECIAL MENU
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
HLC CLIP LEVEL : Select HLC function ON and set the HLC
CLIP LEVEL.(0~06)
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Select ON/OFF in the BACK LIGHT function.
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶BACK LIGHT >
BACK
< NEAR / RIGHT ▶LEVEL>
- LINE LOCK
- HLC LEVEL
SPECIAL MENU
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
HLC LEVEL : Set the HLC LEVEL.(0~02)
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Select ON/OFF in the LINE LOCK function.
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶BACK LIGHT >
BACK
< NEAR / RIGHT ▶LEVEL>
- V PHASE
- APERTUREGAIN
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
SPECIAL MENU
Set the APERTUREGAIN value.(0~15)
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
If you set ON in the LINE LOCK menu, you can set
the V PHASE.
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
BACK
< NEAR / RIGHT ▶BACK LIGHT >
BACK
< NEAR / RIGHT ▶APERTURE >
- DNR LEVEL
32 MIN PTZ CAMERA
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
BACK
< NEAR / RIGHT ▶FLICKERLESS >
Select ON/OFF in the FLICKERLESS function.
Select :
Set OFF :
or
NEAR
NEAR
Set ON :
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
BACK
< NEAR / RIGHT ▶ DNR LEVEL >
Set the DNR LEVEL from AUTO, OFF and 1 ~ 10.
Select :
Set OFF :
or
NEAR
Set ON :
NEAR
33 MIN PTZ CAMERA
- FLICKERLESS
On Screen Display Menu
On Screen Display Menu
- WDR MODE
5 Clear Menu
Set the WDR MODE from OFF, LEV1 ~LEV7.
SPECIAL MENU
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS
: OFF
BACK LIGHT
: OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Select :
Set OFF :
or
NEAR
Clears the PTZ position and function value.
Set ON :
NEAR
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
BACK
< NEAR / RIGHT ▶ WDR MODE >
▶
▶
▶
▶
▶
EXIT
< NEAR / RIGHT ▶ CLEAR >
7) CAMERA RESET
CLEAR MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
▶ YES NO
▶
▶
▶
▶
▶
▶
▶ PRESET CLEAR:
< SEL ▶ NEAR LEFT /RIGHT>
Make initialize the setting value which is set in CAMERA MENU.
Move :
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
▶
Select :
select :
NEAR
Set OFF :
or
NEAR
Set ON :
NEAR
<YES> NO
SAVE
BACK
< NEAR / RIGHT ▶ RESET >
EXIT
6 PTZ Reset
It is a reset function.
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
▶
▶
▶
▶
▶
35 MIN PTZ CAMERA
34 MIN PTZ CAMERA
EXIT
< NEAR / RIGHT ▶ RESET >
SPECIFICATIONS
Image Sensor
3.6
0
Scanning system
Scanning Frequency
Ø3
Ø57.
00
Total Pixels
Sync. System
Resolution
Min. illumination
151.30
Video Output
1.0 Vp-p (75 ohm, composite)
Zoom Ratio
Optical x12, Digital x32 Zoom
Focal Length
f = 3.8 mm ~ 45.6 mm
Aperture Ratio
F1.6 (wide) ~ F2.7 (tele)
Focus
Auto / Zoom-Trig / Manual
Focus Distance
0.1 / 1.0 / 1.3 / 2.0 / 6.0 m
E. Zoom
Off / Max 2x~32x
Exposure
Auto / Shutter PRI / Manual / IRIS PRI
Off / On (Auo Max 30dB)
NTSC : 1/60 ~ 1/100,000 sec PAL : 1/50 ~ 1/100,000 sec
Off / Max 2x~512x
Flickerless
Off / On
Brightness
1 ~15 steps
WDR / BLC
Off / WDR / BLC
Day&Night
Auto / Sens-in / Ext / Day / Night
Image DNR
ATW / One-Push / Indoor / Outdoor / Manual / Auto
Off / Manual / Auto
HR
Off / 1~7 steps
Mirror
Off / H / V / H+V
Sharpness
Effect
Freeze
Intelligent
123.50
Color DSS : 0.001 lux , BW DSS : 0.0004 lux
More than 50dB (AGC off)
White Balance
Privacy Mask
Special
Sync Mode
1 ~ 16 steps
Off / Negative / B&W
Off / On
Privacy / MD / OD
Max. 4 Programmable zones
Sync / Phase / Comm
INT / LL
Phase
0 ~ 255 steps
Display
Disp Sel / Init Sel / Set Title / Set Init Msg / Language
Disp Sel(Off / On)
ID / Title / Zoom Ratio
Init Sel(Off / On)
ID / Baud Rate / Protocol / Version / Init Msg
Protocols
Communication
27.80
800 TV lines (BW)
Color : 0.5 lux , BW : 0.2 lux
12x Day & Night Zoom Lens
Digital Shutter Speed
36 MIN PTZ CAMERA
Internal
700 TV lines (COLOR)
Lens type
Shutter Speed
92.00
Interlace
NTSC : 15.734KHz(H), 59.94Hz(V) PAL : 15.625KHz(H), 50Hz(V)
S/N Ratio
Gain Control
108.45
1/4" SONY Super HAD II(Double Scan) CCD
NTSC : 1028(H) × 508(V) PAL : 1028(H) x 596(V)
Power Consumption
Operating Temperature
Operating Humidity
Certification
PELCO-D, PELCO-P, WONWOO
RS-485
DC12V(±10%), 1.5A
0ºC ~ +50ºC (Indoor )
20% ~ 75% RH
CE, FCC
37 MIN PTZ CAMERA
DIMENSIONS (mm)
QUICK COMMAND
PROTOCOL
'D'
'P'
WONWOO
GOTO PRESET
1~63 PRESET
1~63 PRESET
1~63 PRESET
SET PRESET
1~63 SET PRESET
1~63 SET PRESET
1~63 SET PRESET
GOTO TOUR
71~78 PRESET
71~78 PRESET
71~78 PRESET
SET TOUR
71~78 SET PRESET
71~78 SET PRESET
71~78 SET PRESET
GOTO SCAN
81~84 PRESET
81~84 PRESET
81~84 PRESET
SET SCAN
81~84 SET PRESET
81~84 SET PRESET
81~84 SET PRESET
GOTO PATTERN
91~94 PRESET
91~94 PRESET
91~94 PRESET
SET PATTERN
91~94 SET PRESET
91~94 SET PRESET
91~94 SET PRESET
FLIP
90 PRESET
90 PRESET
90 PRESET
AUTO SCAN
99 PRESET
99 PRESET
99 PRESET
START MENU
95 SET PRESET
95 SET PRESET
95 SET PRESET
39 MIN PTZ CAMERA
38 MIN PTZ CAMERA
FUNCTION
Memo