Untitled - advantek technologies co., ltd.

Table of Contents
Optical Time Domain Reflectometers (OTDR)
M700 Compact Single-mode OTDR . . . . . . . . . . . . . . . . . . . . . . . 3
M200 Handheld OTDR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OFL-250 Handheld OTDR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OFL-200 Single-mode OTDR . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fiber Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Fiber Optic Inspection Microscopes
OFS 300 – Optical Microscope. . . . . . . . . . . . . . . . . . . . . . . . . .
VS 300 – View Safe Video Microscope . . . . . . . . . . . . . . . . . . . .
VFS 2 – Video Microscope. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCP 1 - USB Video Capture Port. . . . . . . . . . . . . . . . . . . . . . . . .
Visible Laser Sources
HiLite - Compact Visible Red Laser Source . . . . . . . . . . . . . . . . . 49
VFI 2 - Visible Red Laser Source . . . . . . . . . . . . . . . . . . . . . . . . 49
MT Tracer - Multi-fiber Visual Fault Identifier. . . . . . . . . . . . . . . . 49
Fiber Optic Loss / Return Loss Test Sets
TurboTest 500B - Broadband Loss/Return Loss Test Set. . . . . . . . 13
OLTS5 - Broadband Loss Test Set. . . . . . . . . . . . . . . . . . . . . . . . 14
Optical Power Meters
OPM1 – Optical Power Meter. . . . . . . . . . . . . . . . . . . . . . . . . . .
OPM4 – Optical Power Meter with Set Reference. . . . . . . . . . . . .
OPM4 – FTTX PON Power Meter. . . . . . . . . . . . . . . . . . . . . . . . .
OPM5 – Optical Power Meter with Set Reference
& Data Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fiber Optic Talk Sets
FTS 1 - Single-mode or Multimode Talk Set. . . . . . . . . . . . . . . . . 50
FTS 2 - Long Range Single-mode Talk Set. . . . . . . . . . . . . . . . . . 50
FTS 20C - Clip-on Coupler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
15
16
17
Fiber Optic Attenuators
SVA 1 - Single-mode Variable Attenuator. . . . . . . . . . . . . . . . . . . 51
VOA 5 - Variable Fiber Optic Attenuator. . . . . . . . . . . . . . . . . . . . 52
18
Light Sources
OLS1 – LED Light Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OLS1-DUAL – LED Light Source with Wave ID. . . . . . . . . . . . . . .
OLS2-DUAL – Laser Light Source with Wave ID. . . . . . . . . . . . . .
OLS4 – Integrated Laser and LED Light Source with Wave ID. . . .
OLS7 – Triple Wavelength Laser Source with Wave ID . . . . . . . . .
OLS7-FTTH – Triple Wavelength Laser Source with Wave ID. . . . .
Fiber Optic Loss Test Kits
CKM 2 – Multimode Kit with Set Reference. . . . . . . . . . . . . . . . .
CKSM 2 – Multimode/Single-mode Kit with Set Reference. . . . . .
MLP1 – Basic Multimode Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . .
MLP4-2 – Multimode Kit with Wave ID & Set Reference. . . . . . . .
MLP5-2 – Multimode Kit with Wave ID, Set Ref. & Data Storage . .
SLP4-6D – Single-mode Kit with Wave ID & Set Reference. . . . . .
SLP4-7 – Triple Wave Kit with Wave ID & Set Reference. . . . . . . .
SLP4-FTTH – Triple Wave Kit with Wave ID & Set Reference. . . . .
SLP5-6D – Single-mode Kit with Wave ID & Set Reference. . . . . .
SLP5-7 – Triple Wave Kit w/ Wave ID, Set Ref. & Data Storage. . . . .
SLP5-FTTH – Triple Wave Kit w/ Wave ID, Set Ref. & Data Storage. . .
SMLP4-4 – Single-mode/Multimode Kit with
Wave ID & Set Reference.. . . . . . . . . . . . . . . . . . . . . . . . . . .
SMLP5-5 – Single-mode/Multimode Kit with
Wave ID, Set Reference & Data Storage. . . . . . . . . . . . . . . . . .
45
46
47
48
19
20
21
22
23
23
Fiber Identifiers
OFI-200 Optical Fiber Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . 53
OFI-400 Optical Fiber Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . 53
OFI-FTTx Active ONT Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . 55
24
26
28
29
31
33
35
35
37
39
39
AFL Telecommunications’ Noyes Test & Inspection Equipment
product line offers a comprehensive set of fiber optic test equipment
for measuring, maintaining and documenting theperformance of
fiber optic networks. In every area of manufacturing, AFL Telecommunications combines the latest equipment, production techniques
and test systems to create products with world-class performance.
41
43
Test & Inspection
4Q08
1
2
M700 Compact Single-mode
OTDR
The Noyes M700 from AFL Telecommunications is a compact, full
featured, single-mode OTDR that includes an integrated Visual
Fault Locator (VFL), an Optical Power Meter (OPM) displaying up to
three wavelengths simultaneously, and a large transflective touch
screen display suitable for both indoor and outdoor operation.
The M700 OTDR supports Real-Time, Full-Auto, and Expert
(manual) modes, precision event analysis, dual-wavelength
testing, rich file naming, and an intuitive job set-up functionality.
In addition to OTDR event analysis, pass/fail acceptance values,
and marginal warning, specific values can be set to alert the test
operator of failing or marginal events. Using one of the Least
Squares Approximation (LSA) loss methods, events may be added
or deleted manually.
Features
•• 38 / 36 dB dynamic range @ 1310 / 1550 nm
•• Integrated Optical Power Meter (OPM) and Visual Fault Locator
(VFL, 650 nm)
•• LSA Measurements and manual events in Expert mode
•• Pass/Fail Event and Link Thresholds settings
•• OTDR results saved as industry standard (GR-196) .SOR files
•• OPM stores results and displays up to three wavelengths simultaneously
•• Large, high bright, sunlight readable, transflective touchscreen
•• Tool-free, switchable adapters (SC/FC/LC)
•• Integrated fiber launch ring holder
•• 2 USB host ports
•• USB drive and Windows® compatible software included
Thousands of OTDR and OPM test results can be stored internally
or on the supplied USB drive, and are transferable via a USB cable
or drive to a computer for viewing, printing and analyzing with
supplied Windows® compatible software. Saved OPM loss values
for a cable in one or two directions can be displayed in a table on
the M700 for evaluation and comparison.
With short dead zones, a dynamic range of 38 dB, and greater
than 8-hour battery life during continuous testing, the M700 is
perfect for testing optical fibers in service provider metro areas.
Ordering Information
Model
Description
Test Port Adapters
M700-11-0901PR 1310/1550 nm single-mode OTDR SC, FC, and LC *
* ST test port adapter is available (order separately).
Standard accessories include are USB Flash drive, PC software for OTDR trace analysis and
OPM Loss reporting, AC adapter, user guide, soft carry case, 1.25 and 2.5mm universal
adapters for VFL and OPM, SC, FC and LC adapters for the OTDR (ST available, purchased
separately).
continued on the next page
© 2008, AFL Telecommunications, all rights reserved. M700-00-2000 Revision 1D, 05. 30. 08
Specifications are subject to change without notice.
3
M700 Compact Single-mode OTDR
Specifications
OTDR Specifications
Power Meter Specifications
Emitter Type
Laser
Safety Class
Class 1 FDA 21 CFR 1040.0 & 1040.11
Center Wavelengths
Dynamic Range (SNR = 1)
Calibrated Wavelengths
850, 980, 1310, 1490, 1550, 1625 nm (displays
up to three simultaneously)
1310/1550 nm
Detector Type
Filtered InGaAs detector
38 / 36 dB (1310/1550 nm)
Measurement Range (dBm)
+26 to -50 dBm
±0.25
4
0.9 m
Accuracy
5.5 m
Measurement Units
dB, dBm, mW
5, 10, 30, 100, 300 ns, 1, 3, 10, 20 ms
Wavelength ID 5
Yes
250 m to 256 km
Set Reference
Yes
max. 64,000 points
Data Storage
Yes
Data Point Spacing
0.125 m (range 2 km)
0.25 m (range = 4 km)
0.5 m (range = 8 km)
Range/# of data points (range 16 km)
Tone Detection
270 Hz, 330 Hz, 1 kHz, 2 kHz
Group Index of Refraction (GIR)
1.4000 to 1.6000
Size
27.4 x 19.3 x 7.1 cm (10.8 x 7.6 x 2.8 in)
± (1 + 0.0005% x distance + data point spacing)
Weight
2.3 kg ( 5 lb)
Bellcore GR-196 Version 1.1
Operating Temperature
-10 to +50°C, 0 to 90% RH (non-condensing)
Internal flash memory
Storage Temperature
-20 to +60°C, 0 to 90% RH (non-condensing)
USB flash drive
Power
Event Dead Zone
1
Attenuation Dead Zone
2
Pulse Widths
Range Settings
Distance Sampling Points
Distance Uncertainty (m)
3
Trace File Format
Trace File Storage Media
General Specifications
Rechargeable Li-Ion or AC power adapter
6
> 8 hours continuous OTDR testing
Downloadable from OTDR directly to PC
Battery Life
Trace File Storage Capacity
Internal 1000 fibers
Recharge Time 7
4 hours
Data Transfer to PC
USB
Display
6.5 inch (16.51 cm), color, transflective
OTDR Modes
Full Auto, Real Time, Expert
Tool Free adapters
Modular cleanable SC/ST/FC/LC
4 Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
5 Automatic wavelength identification and switching when used with Noyes Wave ID Series
Light Sources.
6 Typical, depending on display brightness.
7 Typical, from fully discharged to fully charged state, unit may be operating.
All specifications are subject to change.
All specifications valid at 25°C unless otherwise specified.
External battery charger available.
1 Typical distance between the two points 1.5 dB down each side of a reflective spike
caused by a -45 dB event using 5 ns pulse width.
2 Typical distance from event location to point where trace is within 0.5 dB of backscatter
caused by a -45 dB event using 5 ns pulse width.
3 Does not include GIR uncertainty.
Visual Fault Locator Specifications
Emitter Type
Laser
Safety Class
Class II FDA 21 CFR 1040.10 & 1040.11; IEC
825-1:1993, EN60825-1:1994
Model Number
Description
Wavelength
650 nm
FR1-SM-1KM-SC-FC
Fiber Ring SM SC/FC 1000m
Output Power (nominal)
0.8 mw
FR1-SM-1KM-SC-LC
Fiber Ring SM SC/LC 1000m
FR1-SM-1KM-ASC-SC
Fiber Ring SM SC-APC/SC-UPC 1000m
8500-20-0900
Wet Cleaning Kit for SC/FC/ST/LC Connectors
OTDR Fiber Accessories
© 2008, AFL Telecommunications, all rights reserved. M700-00-2000 Revision 1D, 05. 30. 08
Specifications are subject to change without notice.
4
M200 Handheld OTDR
The Noyes M200 from AFL Telecommunications offers unmatched OTDR capabilities
in a handheld package weighing less than 1 kg (2 lb). Multimode, Single-mode, and
‘Quad’ wavelength models are offered. With short dead zone and intermediate range
specifications, the M200 is ideal for Tier 2 testing of premises (building and campus)
networks or certification and troubleshooting of FTTX PON networks. And its bright,
transflective display makes it suitable for both indoor and outdoor operation.
The M200 is based on a new hardware/software platform that supports automatic and
manual setup, precision event analysis, dual-wavelength testing, rich file naming and
folder setup, 6-hour battery life, internal and removable media data storage, and USB
connectivity. Test ports are equipped with tool-free adapters, which can be changed in
seconds. A custom-designed polycarbonate case and shock-absorbing boot make it our
most rugged OTDR ever.
Results are saved as industry standard .SOR files, which can be viewed, printed, and
analyzed on a PC using free-ware available to you and your customers (go to www.afltele.
com to download). Unit firmware, user settings, and test results are saved in non-volatile
memory. Thus the M200 may be stored with battery removed for an extended period of
time and still be up and running in seconds when needed.
New Feature
USB Host Port offers a new convenient way to transfer data from the M200 to a PC. By
using a standard USB Flash Drive to transfer traces, the user no longer needs a USB Cable,
ActiveSync or a Compact Flash reader. Using the Tools in the M200 File Manager, one or
more folders or files can be copied to a USB Flash Drive for transfer to a PC. Thousands of
files will fit on a 64 MB or larger USB Flash Drive.
Features
•• Handheld, 0.9 kg (2 lb)
•• 22 dB (MM), 26 dB (SM) dynamic range
•• Integrated VFL (650 nm)
•• Tool-free, switchable adapters
•• Transflective (indoor/outdoor) touchscreen display
•• USB Host and Function Ports
Applications
•• Tier 2 testing of premises networks
•• FTTX PON certification and
troubleshooting
•• Fast fault location
•• Splice verification
•• Network documentation
Ordering Information
Model
Description
Test Port Adapters
M200-00-0900PR 850/1300nm multimode and 1310/1550nm single-mode OTDR (1) ST, (2) SC, and (1) FC *
M200-11-0900PR 1310/1550nm single-mode OTDR
SC and FC *
M200-12-0900PR 850/1300nm multimode OTDR
ST and SC *
* LC test port adapters are available (order separately).
NOTES:
1. All models include a rugged, soft-sided carry case with shoulder strap, 110/220 VAC power adapter with country-specific power
cord, and user guide.
2. M200 Standard OTDR supported languages: English, French, German, Italian, Portuguese and Spanish. For Chinese/Taiwanese,
Japanese, or Korean models part numbers, please contact Noyes.
© 2006-2008, AFL Telecommunications, all rights reserved. M200-00-2000 Revision B, 08. 25.08
Specifications are subject to change without notice.
5
M200 Handheld OTDR in a Hard Case
The Noyes M200 OTDR is also available in a tough injection molded ABS carrying case.
The rugged transit case has a full length hinge, padlock loops, secure snap latches and
an O-ring seal to protect the contents from dust and water. In addition to the OTDR, the
custom case has room for cleaning products, launch and receive rings, documentation
and more. Order the Hard Case alone or with one of the M200 configurations. Add test
accessories such as fiber rings and cleaning kits to be ready to clean and test fiber optic
networks.
M200 OTDR with standard accessories
M200 Hard Case Ordering Information
The M200 Hard Case option should be specified when ordering the M200 OTDR. For the
M200 OTDR in a Hard Case ordering information, refer to the table below.
Model Number
Description
1400-01-0075PZ
Hard Case for M200
M200-00-0903PR
850/1300nm multimode and 1310/1550nm single-mode M200 OTDR in Hard Case
M200-11-0904PR
1310/1550nm single-mode M200 OTDR in Hard Case
M200-12-0902PR
850/1300nm multimode M200 OTDR in Hard Case
NOTE: Fiber rings and cleaning supplies are not included with the M200 in the Hard Case option, they must be purchased separately.
To order fiber rings or cleaning supplies with your M200, refer to the ‘Accessories Ordering Information’ table below.
Accessories Ordering Information
M200 OTDR with standard and optional accessories
Model Number
Fiber Rings
Description
FR1-M5-150-x1-x2
Standard, 1 fiber, 50/125 mm multimode, 150m
FR1-L5-150-x1-x2
Standard, 1 fiber, Laser Optimized, 50 mm multimode, 150m
FR1-M6-150-x1-x2
Standard, 1 fiber, 62.5/125 mm multimode, 150m
FR1-SM-150-y1-y2
Standard, 1 fiber, single-mode, 150m
Cleaning Accessories
8500-20-0900
Wet Cleaning Kit (shown) for SC/FC/ST/LC connectors.
Includes:
•• 8500-10-0016MZ, Cletop-SB.
•• CCTS-25-0900MZ, Connector Cleaning Tips for 2.5mm ferrule in adapters or
sockets (SC, FC, ST in adapters). Blue (40 sticks per tube). Qty = 1 tube
•• CCTS-12-0900MZ, Connector Cleaning Tips for 1.25mm ferrule in adapters or
sockets (LC, MU in adapters). Green (40 sticks per tube). Qty = 1 tube
•• FCC2-00-0900, optical quality Cleaning Fluid for fiber connector end faces.
8500-20-0901
Dry Cleaning Kit
Includes:
•• 8500-10-0016MZ, Cletop -SB.
•• 8500-10-0024MZ, ACT-01 2.5mm adapter cleaning tips (Qty = 200).
8500-05-0001MZ
One-Click Cleaner SC
8500-05-0002MZ
One-Click Cleaner LC/MU
NOTE: When ordering Fiber Rings, specify connector types (x1, x2, y1,y2)
© 2006-2008, AFL Telecommunications, all rights reserved. M200-00-2000 Revision B, 08. 25.08
Specifications are subject to change without notice.
6
M200 Handheld OTDR
Specifications
OTDR Specifications
Multimode
Single-mode
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.10 and 1040.11, IEC EN60825-1:2007-03
Center Wavelengths
850 / 1300 nm
1310 / 1550 nm
Wavelength Tolerance
± 20 / ± 30 nm
± 20 / ± 30 nm
Dynamic Range (SNR = 1)
22 dB
26 dB
Event Dead Zone 1
1.5 m
1.5 m
Attenuation Dead Zone 2
9m
9m
Pulse Widths 3
10, 30, 100, 300 ns, 1, 3 µs
10, 30, 100, 300 ns, 1, 3, 10 µs
Range Settings
250 m to 32 km
250 m to 208 km
Data Points
Up to 16,000
Up to 16,000
Data Point Spacing
0.25 m (range < 4 km)
Range/16000 (range > 8 km)
Group Index of Refraction (GIR)
1.4000 to 1.6000
Distance Uncertainty (m)
± (1 + 0.005% x distance + data point spacing)
Trace File Format
Bellcore GR-196 Version 1.1
Trace File Storage Medium
Internal non-volatile memory, removable Compact Flash Card (not included), and USB Flash Drive
Trace File Storage Capacity
> 100 internal; thousands on Compact Flash or USB Flash Drive
Trace File Transfer to PC
USB Flash Drive Type 1.1, Compact Flash or Mini USB Cable with ActiveSync
Visual Fault Locator Specifications
Emitter Type
Laser
Safety Class
Class II FDA 21 CFR 1040.10 & 1040.11; IEC 825-1:1993, EN60825-1:2007-03
Wavelength
650 nm
Output Power (nominal)
0.8 mw
General Specifications
Size (in boot)
23 x 11 x 7 cm (8.8 x 4.3 x 2.8 inches)
Weight
0.9 kg (2 lb)
Operating Temperature
-10 to +50 °C
Storage Temperature
-20 to +60 °C
Relative Humidity
0 to 95% RH (non-condensing)
Power
Removable LiIon or 110/220 VAC power adapter
Battery Life4
6 hours
Recharge Time 4 & 5
3 hours
NOTES:
1. Typical distance between the two points 1.5 dB down each side of a reflective spike caused by a -40 dB (Multimode) or -45 dB (single-mode) event using 10 ns pulse width.
2. Typical distance from event location to point where trace is within 0.5 dB of backscatter.
3. 3 µs pulse width not available at 850 nm.
4. New battery.
5. Typical, from fully discharged to fully charged state, unit may be operating.
All specifications are subject to change.
All specifications valid at 23°C ± 2°C (73.4°F ± 3.6°F) unless otherwise specified.
© 2006-2008, AFL Telecommunications, all rights reserved. M200-00-2000 Revision B, 08. 25.08
Specifications are subject to change without notice.
7
OFL 250 Handheld OTDR
The Noyes OFL 250 from AFL Telecommunications is a single-mode OTDR with an
integrated Optical Power Meter (OPM), Laser Source (OLS), and Visual Fault Locator (VFL)
in a handheld package weighing only 0.8 kg (1.7 lb). With short dead zone and mid-range
dynamic range performance, the OFL 250 is ideal for testing optical fibers in service
provider metro areas and FTTx networks.
The OFL 250 provides automatic and manual setup, precision event analysis, multiplewavelength testing, a 12-hour battery life, internal data storage, and USB connectivity.
OTDR and OPM test ports are equipped with tool-free adapters, which can be changed in
seconds.
Results are saved as industry standard .SOR files, which can be transferred to a PC for
viewing, printing, and analyzing with the supplied Windows® compatible software.
Features
•• Handheld, 0.8 kg (1.7 lb)
•• Multiple-wavelength single-mode OTDR
•• 1.5 m (typ.) event dead zone
•• 26 dB dynamic range
•• Integrated OPM, OLS, and VFL (650 nm)
•• Tool-free, switchable adapters for OTDR & OPM ports (FC, SC, ST, LC, E2000 are available)
•• Bellcore (GR-196) .SOR file format
•• Rechargeable (> 12 hours) Li-Ion battery or AC power
•• 3.5-inch, indoor/outdoor LCD
•• Windows® compatible software to view, print, and archive test record
•• Mini USB Port (connect to PC with cable)
Ordering Information
Model Number
Description
Wavelengths
OFL2-26-0910PR
OFL 250 Single-mode OTDR
1310/1550 nm
OFL2-26-0924PR
OFL 250 Single-mode OTDR
1310/1550/1625 nm
Note: All OFL 250 models come with: a carry case, SC and FC adapters for the OTDR/OLS port, 2.5 mm universal adapters
for the OPM and VFL ports, USB cable (connects with normal (Type A) USB port on your PC), AC power adapter, country-specific
power cord, and a user guide.
continued on the next page
© 2007-2008, AFL Telecommunications, all rights reserved. OFL2-26-2000 Revision C, 04. 21. 08
Specifications are subject to change without notice.
8
OFL 250 Handheld OTDR
Specifications
Optical Light Source Specifications
OTDR Specifications
Emitter Type
Laser, Class I (FDA 21 CFR 1040.10 and
1040.11, and IEC 60825-1)
Single-mode
Fiber Type
Single-mode
1310 / 1550/ 1625 nm
Center Wavelengths
1310 / 1550 / 1625 nm
Wavelength Tolerance
± 20 / ± 20 / ± 10 nm
Wavelength Tolerance
± 20 / ± 20 / ± 10 nm
Dynamic Range (SNR=1)
26 / 26/ 26 dB
Spectral Width (FWHM)
2 nm (max)
Event Dead Zone 1
1.5 m
Internal Modulation
1 kHz, 2 kHz
Wavelength ID
Compatible with Noyes Optical Power Meters &
Light Sources
Output Power Stability
< ± 0.25 dB after 15 min
Output Power
– 3 dBm
Emitter Type
Laser
Safety Class
Class I FDA 21 CFR 1040.0 & 1040.11
Fiber Type
Center Wavelengths
Attenuation Dead Zone @ 5ns 2 Typ.6.0 m, max. 6.5 m
Pulse Widths
5, 10, 30, 100, 300 ns, 1, 3, 10 µs
Range Settings
250 m to 256 km
Data points
Up to 16,000
Data Point Spacing
12.5 cm (range < 4 km),
Range/16000 (range > 4 km)
Visual Fault Locator Specifications
Group Index of Refraction (GIR)
1.4000 to 1.6000
Emitter type
Laser
Distance Uncertainty (m)
± (1 + 0.005% x distance + data point spacing)
Safety Class
Trace File Format
Bellcore GR-196 V.1.1
Class II (FDA 21 CFR 1040.10 and 1040.11, IEC
60825-1:1994, IEC 825-1:1993 )
Trace File Storage Medium
Internal memory (>1000 traces)
Wavelength
650 nm
Data Transfer to PC
USB cable
Output Power (nominal)
0.8 mW into SMF-28
OTDR Modes
Full Auto, End Locate, Expert, Live
1. Typical distance between the two points 1.5 dB down each side of a reflective
spike caused by a -45 dB event using 10 ns pulse width.
General
2. Typical distance from event location to point where trace is within 0.5 dB of
backscatter.
Size (in boot)
19 x 11.2 x 4.7 cm (7.5 x 4.4 x 1.9 in)
Weight
0.8 kg (1.7 lb)
Optical Power Meter Specifications
Operational Temperature
-10 to +50°C, 0 to 95% RH (non-condensing)
Storage Temperature
-20 to +60°C, 0 to 95% RH (non-condensing)
Power
Rechargeable LiIon or AC adapter
Battery life
(backlight ON in OTDR mode)
> 12 hours
Display
LCD, 320 x 240, 3.5 inch (89 mm) , color,
transflective
OTDR and OPM ports
Switchable. See website or contact AFL for
available adapter types.
Calibrated Wavelengths
1310, 1490, 1550, 1625 nm
Detector Type
InGaAs
Measurement range
+23 to - 45 dBm
Tone detect range
+3 to -35 dBm
Wavelength ID range
+3 to -35 dBm
Accuracy
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, mW, nW
© 2007-2008, AFL Telecommunications, all rights reserved. OFL2-26-2000 Revision C, 04. 21. 08
Specifications are subject to change without notice.
9
OFL 200 Single-mode OTDR
The OFL 200 OTDR sets new standards for size, weight, ease-of-use, and value in a
telco/broadband OTDR. Smaller than many optical loss test sets, the OFL 200 has the
range, features, and price to make it the perfect OTDR for outside plant crews installing
and maintaining optical fiber cables in broadband, metro, access, and FTTH networks.
Unlike ‘optical fault locators’, which detect only reflective events, the OFL 200 is a true
OTDR, which detects fiber backscatter as well as fresnel reflections. Thus, the OFL 200
can locate reflective and non-reflective breaks, including those caused by crushed fibers.
In addition, the OFL 200 provides an integrated 650 nm visual fault locator (VFL) for shortdistance troubleshooting and fiber tracing.
Features and Applications
•• Rugged, handheld, lightweight
•• Designed for field use
•• 1550 or 1625 nm single-mode OTDR
•• Locates reflective and non-reflective
breaks
•• Built-in 650 nm visual fault locator (VFL)
with universal adapter
•• Switchable OTDR port adapter
•• Cursor and zoom controls to measure
event loss, reflectance, and location
•• Automatic, semi-automatic, and manual
setup modes
•• Launch level connection quality indicator
•• Large LCD with Backlight
•• Free Windows® compatible software to
view, print, and archive test records
•• Rechargeable NiMH battery pack, AC
adapter, or optional AA alkaline
•• Wide temperature range: -10 to + 50°C
Ordering Information
Model
Includes
OFL 200-1550
OFL 200-1625
SC, FC adapter caps (ST, LC available), universal AC power adapter,
country- specific line cord, user's
guide, and carry case.
In its [Full Auto] mode, the OFL 200 measures fiber length and sets range, pulse width,
and averaging time automatically. [Full Auto] mode is ideal for operators not familiar with
OTDRs. [Semi Auto] mode allows the user to set range while the OFL 200 sets all other
parameters. [Manual] mode is available for experienced users. [Live] mode is provided for
first connector checking and troubleshooting.
The fast change switchable adapter allows the OTDR to interface launch cables with a
variety of connector styles. The OFL 200 can internally store up to 48 traces. Using the
supplied serial cable, saved traces can be transferred to a PC for archiving, printing, and
analyzing with the supplied Trace600 Windows® software. Test results are stored in Bellcore [*.sor] GR-196 Version 1.1 format.
Specifications
OFL 200 OTDR
Emitter type
Safety class
Center wavelength (nominal)
Dynamic range (SNR = 1)
Maximum fiber length
Event dead zone 1
Attenuation dead zone 2
Number of data points
Resolution
Laser
Class I, FDA 21 CFR 1040.10 & 1040.11
1550 nm
1625 nm
24 dB @ 10 µs, 3 min. test
23 dB @ 10 µs, 3 min. test
70 km
2 m typical / 3 m maximum
14 m typical / 18 m maximum
4000 on ranges > 4 km
1 m on ranges > 4 km; Range / 4,000 on ranges > 4 km
Visual Fault Locator (VFL)
Emitter type
Safety class:
Wavelength
Output power (nominal)
General
Size (H x W x D)
Weight
Operating temperature
Storage temperature
Power
Battery life with backlight ON
Laser
Class II, FDA 21 CFR 1040.10 & 1040.11
IEC 825-1: 1993, EN60825-1: 1994
650 nm
0.8 mW into 9 μm single-mode optical fiber
190 x 112 x 47 mm (7.5 x 4.4 x 1.9 inches)
0.6 kg (1.3 lb)
-10 °C to + 50 °C, 0 to 95% RH (non-condensing)
-20 °C to + 60 °C, 0 to 95% RH (non-condensing)
Rechargeable NiMH or AC adapter. Optional 4 x AA Alkaline
NiMH: > 8 hours; 4 x AA: > 13 hours
1
1.5 dB down from each side of the peak, -45 dB reflective event
From the start of an event to within 0.5 dB of backscatter, -45 dB reflective event.
2
© 2004, AFL Telecommunications, all rights reserved. OFL2-20-2000 Revision 1G, 9.27.06
Specifications are subject to change without notice.
10
OTDR Fiber Rings
Measuring an insertion loss of the near-end and / or far-end connection of a fiber optic
link with an OTDR requires a launch and / or receive test cable. A launch cable, which
connects the OTDR to the link under test, reveals the insertion loss and reflectance of the
near-end connection. A receive cable, which connects to the far-end of the link, reveals
the insertion loss and reflectance of the far-end connection. Launch and receive test
cables can range from 150 m to 1 km (or longer) in length. Because very long test cables
are impractical to transport and use, Noyes offers coiled lengths of 50 mm multimode,
62.5 mm multimode, or single-mode fiber packaged in compact rings.
Fiber Ring, MM - 150 m
Fiber Rings of 150 m of fiber are ideal for premises fiber network test applications. Fiber
Rings of 500 m and 1 km of single-mode fiber are designed for broadband, long-haul fiber
network test applications.
Fiber Ring Models
Fiber Ring, SM - 1000 m
Model
Configuration
Fiber Type
Fiber Length
FR1-M5-150- x1- x2
Standard, one fiber
Multimode, 50 mm
150 m (492 ft)
FR1-L5-150-x1-x2
Standard, one fiber, Laser Optimized
Multimode, 50 mm
150m (492 ft)
FR1-M6-150- x1- x2
Standard, one fiber
Multimode, 62.5 mm
150 m (492 ft)
FR1-SM-150- y1- y2
Standard, one fiber
Single-mode
150 m (492 ft)
FR1-SM-500- y1- y2
Standard, one fiber
Single-mode
500m (1640 ft)
FR1-SM-1000- y1- y2
Standard, one fiber
Single-mode
1000m (3280 ft)
FR3-M5-x1-MTRJ
MT-RJ near-end, A and B fibers
Multimode, 50 mm
150 m (492 ft)
FR3-M6-x1-MTRJ
MT-RJ near-end, A and B fibers
Multimode, 62.5 mm
150 m (492 ft)
FR3-SM-x1-MTRJ
MT-RJ near-end, A and B fibers
Single-mode
150 m (492 ft)
FR1-M5-x1-E2000
E2000 to ST, SC, FC, etc., one fiber
Multimode, 50 mm
150 m (492 ft)
FR1-M6-x1-E2000
E2000 to ST, SC, FC, etc., one fiber
Multimode, 62.5 mm
150 m (492 ft)
FR1-SM-y1-E2000
E2000 to ST, SC, FC, etc., one fiber
Single-mode
150 m (492 ft)
FR1-M5-E2000-E2000
E2000 to E2000, one fiber
Multimode, 50 mm
150 m (492 ft)
FR1-M6-E2000-E2000
E2000 to E2000, one fiber
Multimode, 62.5 mm
150 m (492 ft)
FR1-SM-E2000-E2000
E2000 to E2000, one fiber
Single-mode
150 m (492 ft)
x1, x2 — connectors for multimode cables, specify type [ST, SC, ASC (angled SC), FC, AFC (angled FC), LC]
y1, y2 — connectors for single-mode cables, specify type [ST, SC, ASC (angled SC), FC, AFC (angled FC), LC]
Other connector types, fiber types, and fiber lengths will be quoted upon request.
Fiber Ring, Laser Optimized
Continued on the next page
© 2008, AFL Telecommunications, all rights reserved. FR00-00-2000 Revision 1A, 8.25.08
Specifications are subject to change without notice.
11
OTDR Fiber Rings
How to Generate a Baseline Trace Using Fiber Rings
•• Use the Fiber Ring as a launch cable.
Connect the Fiber Ring between your OTDR and the fiber link under test. This will allow
you to measure the loss of the near-end connection.
•• Use the Fiber Ring as a receive cable.
Cconnect the Fiber Ring to the far-end connector of your fiber link under test. This will
allow you measure the loss of the far-end connection.
•• By using Fiber Rings as both launch and receive cables, as shown in the diagram below,
you can measure total insertion loss of the fiber link under test.
fiber ring - launch cable
2
6
7
fiber link under test
fiber ring - receive cable
fiber ring connector
1
4
OTDR port
fusion splice
OTDR
3
5
8
near-end connection
far-end connection
end of receive cable
Example OTDR Test Configuration With Launch And Receive Cables
OTDR port
1
8
end of receive cable
near-end connection
3
6
fiber link under test
fiber ring - launch cable
2
5
far-end connection
fusion splice
4
7
fiber ring - receive cable
OTDR Trace Made Using Launch And Receive Cables
© 2008, AFL Telecommunications, all rights reserved. FR00-00-2000 Revision 1A, 8.25.08
Specifications are subject to change without notice.
12
Turbotest 500B
Optical Loss/Return Loss Test Sets
The TURBOTEST 500B Series offers the latest technology in a single fiber bi-directional
loss and return loss testing. The T500B is a handheld fiber optic test and measurement instrument. It performs Optical Power, Optical Return Loss, and Optical Loss
measurements. Five compact models are available, including the three wavelength
(1310/1550/1625) T506B and (1310/1550/1490) T506B-FTTH. An optional dedicated
digital talk option is available for full time/full duplex communication between test operators while testing other fibers in a bundle.
The T500B can store up to 1000 records (40 files) in any combination of its four operating
modes and if any configuration other than TRIPLE wavelength is selected. If the configuration is TRIPLE wavelength, the T500B can store up to 500 records (40 files). Stored test
results can be transferred to a PC for a complete report generation.
Features
•• Rugged, handheld, designed for field use
•• Passive Optical Networks (PON) testing
•• Single fiber, bi-directional loss and return
loss testing at 1310/ 1490/ 1550nm or
1310/ 1550/ 1625nm
•• TRIPLE wavelength test mode
•• Talk Set option
•• Up to 1000 test records (40 files) storage
and download
•• Free Windows® compatible software to
view, print, and archive test records
•• Lithium-Ion or AC adapter
•• Cost-effective, easy to use
Ordering Information
Model
Includes
All T500 B (1) T500 B, protective rubber boot, APC/
models
UPC test jumper, adapter cap, serial
cable, hex driver, screwdriver, mandrel,
AC adapter, PC software, user’s guide,
and carry case.
When ordering, specify connector type after the model number,
(e.g. T504B-Y-SC is a 1310/1550/ Turbo with 1550 nm Talk
Set Option and a SC connector).
Powered by an internal rechargeable Lithium-lon battery, the T500B comes with protective
rubber boots, PC software and manual, AC adapter/charger, RS-232 serial cable, APC/UPC
reference cable, adapter cap, mandrel, screwdriver, hex screwdriver, warranty registration
card, user’s guide, and carry case.
Specifications
Model
T503B
Calibrated wavelengths (nm)
T504B
T505B
1310, 1550 1310, 1550
Output power (dBm)
Emitter type
Safety class
T506B
1550, 1625 1310, 1550,
1625
T506B-FTTH
1310, 1550,
1490
-5
-5
-5
-5
-5
Laser
Laser
Laser
Laser
Laser
FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1 amended Q2, 2001
Detector type
Insertion loss measurement range
(dB)
Measurement range (dBm)
Measurement units
InGaAs
InGaAs
InGaAs
InGaAs
InGaAs
45
45
45
45
45
+6 to -70
+26 to -50
+26 to -50
+26 to -50
+26 to -50
dB, dBm, µW
ORL dynamic range (dB)
65
Available connector types
ASC or AFC
Power
Lithium-Ion or AC Adapter
Li-Ion battery pack charging temp.
-10 to +45°C
Note: Li-Ion battery pack charging time will increase by 25% at a temperature below -5°C.
Important: Do not charge the Li-Ion battery pack at a temperature above +45°C.
Note: After the model number,
•• Add -T for 40 dB 1310 nm Talk Set option.
•• Add -Y for 40 dB 1550 nm Talk Set option.
•• Example: T506B-Y is 1310/1550/1625 Turbo with 1550nm Talk Set option.
•• T500B instruments are sold individually but normally used in pairs
© 2002, AFL Telecommunications, all rights reserved. T50B-00-20000 Revision F, 9.12.05
Specifications are subject to change without notice.
13
OLTS 5 Optical Loss Test Set
Features
•• Rugged, handheld, designed for field use
•• Integrated dual-wavelength laser source
and optical power meter
•• Automatic bi-directional, dual-wavelength insertion loss measurement
•• Optical power meter and light source
manual test modes
•• Up to 1000 test records (40 files) storage
and download
•• Free Windows® compatible software to
view, print, and archive test records
•• (AA) alkaline. Optional internally recharged NiMH battery pack or AC adapter
•• Cost-effective, easy to use
Ordering Information
Model
Includes
All
OLTS5
models
(1) OLTS5, (2) AA alkaline batteries, protective rubber boot, PC software, adapter cap
of the same connector type as the transmit
port, user’s guide, and carry case.
When ordering, connector type after the model number, for
example OLTS 5-3 SC.
The OLTS5 Optical Loss Test Set series offers end-to-end single-mode testing at either
1310/1550 nm or 1550/1625 nm. The OLTS5 may be operated in automatic or manual
test modes. In its “two-unit” automatic test mode, a pair of OLTS5 test sets may be used
to measure the end-to-end, bi-directional insertion loss of a pair of single-mode fibers at
1310/1550 nm or 1550/1625 nm. Tests are started and controlled by the user from the
OLTS5 configured as the Main unit. Test progress messages and results are displayed on
the Remote unit. Full test results can be reviewed and saved in the Main unit. Thresholds
may be set to provide Pass/Fail results. In its “single-unit” automatic test mode the OLTS5
can measure bi-directional, dual-wavelength insertion loss of patch cords, or fiber optic
cables while they are still on the reel. In the manual operating mode individual OLTS5 test
sets can operate either as an optical power meter (OPM) or dual-wavelength laser source.
The OLTS5 can store dual-wavelength, bi-directional insertion loss results for up to 1,000
fibers. Test results can be organized in up to 20 user-named files. Results are transferred
to a PC via a serial link. Windows® software is provided to view, edit, and print test
results. OLTS5 units are sold individually but normally used in pairs.
Specifications
Model
OLTS5-3
Transmit port (laser source) specifications
Center wavelengths
OLTS5-5
OLTS5-6
1310 /1550 ± 20 nm 1550/1625 ± 20 nm 1310 /1550 ± 20 nm
Emitter type
Laser, Class 1 (FDA and IEC)*
Output power into 9/125 SM fiber
-5 dBm (nominal)
Stability
Insertion loss and power measurement
resolution
± 0.1 dB, up to 8 hours
0.01 dB
Available connector types
SC or FC
Receive port (optical power measurement) specifications
Detector type
Calibrated wavelengths
OPM (manual) mode optical power display
range
OLTS (automatic) mode insertion loss
measurement range
InGaAs
Filtered InGaAs
850, 980, 1300, 1310, 1480, 1550, 1625 nm
+ 10 to – 70 dBm
45 dB
Accuracy at –10 dBm, 25ºC
+ 16 to – 60 dBm
39 dB
± 0.25 dB
Connector types
Thread-on adapter cap mount
General specifications
Display
128 X 64 dot matrix liquid crystal display
Dimensions (H x W x D)
18.5 X 11.1 X 4.6cm (7.3 X 4.4 X 1.8in)
Weight
0.55 kg (1.2 lbs.)
Operating temperature and humidity
Storage temperature and humidity
0 to +50°C, 90% RH (non-condensing)
-20 to +60°C, 95% RH
Power
2 AA Alkaline (2-cell NiMH-or AC adapter optional)
Battery life (typical)
(2) AA - 17 hours; NiMH battery pack - 11 hours
* FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1 amended Q2, 2001
Note: All specifications at room temperature (25ºC) unless indicated otherwise.
© 2002-2008, AFL Telecommunications, all rights reserved. OLT5-00-2000 Revision E, 05.28.08
Specifications are subject to change without notice.
14
OPM1 Optical Power Meter
This portable optical power meter may be used to measure optical power in premises,
telco, or broadband fiber optic networks. When used with an LED or laser light source,
the OPM1 can also measure the attenuation (insertion loss) of multimode or single-mode
cables. With only two controls – ON/OFF and wavelength – the OPM1 is our simplest to
use optical power meter. Optical power in dBm and the calibration wavelength setting are
displayed on an easy-to-read LCD display. The optical input port accepts Noyes thread-on
style connector adapter caps. Adapter caps are required and must be ordered separately.
The OPM1 is fully N.I.S.T. traceable and runs on a standard 9-volt alkaline battery.
Features
Applications
• 850, 1300, 1310, 1550 nm
• Premises (Ge) and broadband (InGaAs)
models
• Displays optical power (dBm)
• Our simplest to use optical power meter
• N.I.S.T. traceable
• The OPM1-2C is calibrated at 850, 1300, 1310, and 1550 nm for testing LAN, Ethernet,
FDDI, Token Ring, and single-mode fiber systems such as Telco, WAN, and CATV.
• The OPM1-3C also operates at 850, 1300, 1310, and 1550 nm but offers greater temperature stability needed for outside plant 1550 nm testing as with WAN, CATV, and Telco
systems.
Specifications
Optical Specifications
Calibration wavelengths
Detector type
Measurement range
Accuracy (@25° C, -10.0 dBm)
Measurement units
OPM1-2C
OPM1-3C
850, 1300, 1310, 1550 nm
850, 1300, 1310, 1550, 1625 nm
Germanium (Ge)
InGaAs
+6 to -60 dBm
+6 to -70 dBm
±0.25 dB
dBm
General Specifications
Power
Typical 60 hours with 9V battery
Adapter caps
order separately (ST, SC, FC, and others available)
Operating temperature
-10 to 50°C
0 to 95% (non-condensing)
Relative humidity
Storage temperature
-30 to 60°C
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
All specifications at 25°C
Ordering Information
Model
Includes
All OPM1 models
Protective rubber boot, 9V battery, manual, and carrying case.
Optical power meters and optical light sources can be packaged together as a kit.
© 2002, AFL Telecommunications, all rights reserved. OPM1-00-2001 Revision N, 6.16.05
Specifications are subject to change without notice.
15
OPM4 Optical Power Meter
The Noyes OPM4 from AFL Telecommunications is a handheld optical power meter
designed for measuring optical power in Premises, Telco, or Broadband networks and for
performing insertion loss measurements on multimode or single-mode fiber optic links.
The OPM4 features automatic wavelength identification and switching (Wave ID)
when used with Noyes OLS series light sources, multiple test Tone detection for fiber
identification, and stores optical references for each calibrated wavelength. A large dualwavelength LCD display with backlight shows measured power [dBm or µW] or insertion
loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID, and estimated
remaining battery life.
The OPM4 optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements. The OPM4 offers a fiveminute auto-off feature and long battery life from common AA alkaline batteries.
The OPM4 is fully N.I.S.T. traceable.
Features
•• Handheld, rugged, lightweight
•• Multimode or single-mode applications
•• Wave ID (auto identification & switching)
•• Multiple-wavelength testing
•• 270Hz, 330Hz, 1kHz, 2kHz Tone detection
•• Large LCD with backlight
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Automatic power-off function
•• Battery gauge
•• Long battery life with 2 x AA alkaline
•• N.I.S.T traceable
Application
•• Premises (Ge), Telco (InGaAs), and
Broadband (+26 dBm) models
•• Passive Optical Networks (PON) testing
Specifications
Optical
OPM4-1D
Calibrated wavelengths (nm)
660, 780,
850 nm
850, 1300, 1310,
1490, 1550
Detector type
OPM4-2D
OPM4-3D
850, 1300, 1310,
1490, 1550, 1625
OPM4-4D
850, 980, 1310, 1490,
1550, 1625
Silicon (Si)
Germanium (Ge)
InGaAs
Filtered InGaAs
Measurement range
+6 to -70 dBm
+6 to -60 dBm
+10 to -75 dBm
+26 to -50 dBm
Tone detect range
+6 to -45 dBm
Wavelength ID range
—
+6 to -50 dBm
+10 to -50 dBm
+6 to -45 for 850 nm +10 to -45 for 850 nm
+6 to -30 dBm
+6 to -25 for 850 nm
+6 to -50 dBm
+6 to -45 dBm for 850 nm
+6 to -30 dBm
+6 to -25 dBm for 850 nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Ordering Information
Model
Includes
All OPM4 models
OPM4 optical power meter, 2 x AA batteries, protective rubber boot, user’s guide, and
carry case.
© 2004-2007, AFL Telecommunications, all rights reserved. OPM4-30-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
16
OPM4-FTTx PON Power Meter
The Noyes OPM4-FTTx from AFL Telecommunications is designed to measure optical
power in FTTH and other passive optical networks (PONs) that use 1490 nm for
downstream data and 1550 nm for downstream video traffic. In addition, the OPM4-FTTx
provides an integrated Visual Fault Locator (VFL) - 650 nm (red) laser for short-range fault
location and connectivity testing.
Equipped with wavelength filters and a dual photo detector, the OPM4-FTTx can separately
and simultaneously measure 1490 and 1550 nm power at the ONT or other points in
an FTTx PON. A large, dual-wavelength LCD display with backlight shows power at both
wavelengths (in units of dB or µW). A “set reference” feature may be used to compare
1490 or 1550 nm power levels (in units of dB) measured at different parts of the network.
Features
•• BPON, GPON, and EPON compatible
•• Simultaneous power measurement at
1490 and 1550 nm
•• Power shown in units of dBm or µW
•• Comparison of power levels in dB
•• Integrated VFL
•• Auto power shut-off feature
•• Dual-wavelength, sunlight readable LCD
display
•• Compatible with APC or UPC connectors
•• Standard alkaline AA batteries
•• Handheld, rugged, lightweight
•• N.I.S.T traceable
Applications
•• ONT splitter installation testing
•• Fault-locating drop cables and F2 fibers
from FDH to ONT
The power meter and VFL ports accept Noyes thread-on style adapter caps and are
compatible with angled or non-angled connectors. The OPM4-FTTx offers an automatic
power shut-off feature, long battery life from standard AA alkaline batteries, and is fully
N.I.S.T. traceable.
Specifications
Power Meter
Calibrated wavelengths
1490 nm, 1550 nm
Signal format
CW or downstream BPON, GPON, or EPON
Detector type
Filtered InGaAs
Measurement range
+10 to -50 dBm @ 1490 nm; +20 to -50 dBm @ 1550 nm
Accuracy*
± 0.5 dB (± 0.35 dB typical)
Resolution
0.01 dB
Measurement units
dB, dBm, μW
VFL Laser
Output power (typical)
0.8 mW
Wavelength (nominal)
650 nm
Safety
Class II, FDA 21 CFR 1040.10 & 1040.11; IEC EN60825-1:2007
General
Power
2 x AA batteries
Battery life (typical)
Power meter:
100 hours
Power meter + VFL: 16 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
Power meter (backlight on):
16 hours
Power meter (backlight on) + VFL: 5 hours
* At calibration power levels of approximately -5 dBm for 1550 nm and -10 dBm for 1490 nm.
All specifications at 25°C
Ordering Information
Model
Includes
OPM4-FTTx
OPM4-FTTx PON power meter, 2 x AA batteries, protective rubber boot, SC adapter for power
meter port, 2.5 mm universal adapter for VFL port, user’s guide, and carry case.
* Additional adapters are available and must be ordered separately
© 2008, AFL Telecommunications, all rights reserved. OPM4-14-2000 Revision 1B, 08.13.08
Specifications are subject to change without notice.
17
OPM5 Optical Power Meter
The OPM5 from AFL Telecommunications is a full-featured, handheld optical power meter
designed for measuring optical power in Premises, Telco, or Broadband networks and for
performing insertion loss measurements on multimode or single-mode fiber optic links.
The OPM5 features automatic wavelength identification and switching (Wave ID)
when used with Noyes OLS series light sources, multiple test Tone detection for fiber
identification, and stores optical references for each calibrated wavelength and up to 500
records per wavelength of power or insertion loss measurements. Using the supplied
Windows® compatible software and USB connection, test records are transferred to a
PC for analysis, printing, and storage. A large dual-wavelength LCD display with backlight
shows measured power [dBm or µW] or insertion loss [dB], calibrated wavelengths [nm],
tone signal [Hz], wavelength ID, and estimated remaining battery life.
Features
•• Handheld, rugged, lightweight
•• Multimode or single-mode applications
•• Wave ID (auto identification & switching)
•• Multiple-wavelength testing
•• 270Hz, 330Hz, 1kHz, 2kHz Tone detection
•• Large LCD with backlight
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Automatic power-off function
•• Battery gauge
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• N.I.S.T traceable
The OPM5 optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements. The OPM5 offers a
five-minute auto-off feature and long battery life from common AA alkaline batteries with
external AC adapter available as an option.
The OPM5 is fully N.I.S.T. traceable.
Specifications
Optical
Calibrated wavelengths
(nm)
OPM5-2D
OPM5-3D
OPM5-4D
850, 1300,
1310, 1490, 1550,
850, 1300, 1310, 1490,
1550, 1625
850, 980, 1310,1490,
1550, 1625
Detector type
Germanium (Ge)
InGaAs
Filtered InGaAs
Measurement range
+6 to -60 dBm
+10 to -75 dBm
+26 to -50 dBm
Tone detect range
+6 to -50 dBm
+10 to -50 dBm
+6 to -45 dBm for 850nm +10 to -45 dBm for 850nm
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -50 dBm
+10 to -50 dBm
+6 to -45 dBm for 850nm +10 to -45 dBm for 850nm
+6 to -30 dBm
+6 to -25 dBm for 850nm
± 0.25 dB
Accuracy*
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries, optional AC adapter
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Application
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
•• Premises (Ge), Telco (InGaAs), and
Broadband (+26 dBm) models
•• Passive Optical Networks (PON) testing
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
Weight
0.26 kg (0.58 lb)
Ordering Information
Model
Includes
All OPM5 models
OPM5 optical power meter, 2 x AA batteries, protective rubber boot, USB cable, Windows® compatible software and user’s guide, OPM5 user’s guide, and carry case.
© 2004-2007, AFL Telecommunications, all rights reserved. OPM5-30-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
18
OLS 1 LED Light Source
The OLS 1 LED light source is a cost-effective, rugged, handheld instrument designed for
performing insertion loss measurements on fiber optic links when used with an opti¬cal
power meter. The LED output is stabilized to ensure accurate test results per current TIA/
EIA requirements. The OLS 1 is easy to operate with only a [Wavelength/ Power] switch,
which selects optical wavelengths or disables unit (position). [Active Output], [Battery],
and [External Power] indicators identify the currently enabled output port, battery charge
status, and external power presence. Weighing only 0.65 lb, the OLS 1 is compact and
convenient for field use. The OLS 1 operates over 60 hours from a typical 9V alkaline
battery. An AC adapter is optional for extended use. The OLS 1 light source is fully N.I.S.T.
traceable.
Applications
Features
•• Rugged, handheld, lightweight
•• 850 and 1300 nm LED (multimode) light
sources (660 nm available)
•• Certify 50 or 62.5 µm multimode
fiber links for any 850 or 1300 nm
applica¬tion, including Gigabit Ethernet
(GBE) per TIA/EIA standards
•• Free 50 µm and 62.5 µm mandrels
•• Long battery life
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
•• Operating at 850 nm, the OLS 1-1C can be used for testing Ethernet, Gigabit Ethernet,
Token Ring, and other multimode LAN systems.
•• Operating at 660 nm, the OLS 1-1C can test 1000µ fiber and trace fibers with the visible
660 nm output.
•• The OLS 1-2C operates at 850 and 1300 nm for use on Ethernet, Token Ring, and FDDI.
The 1300 nm output can also be used to test short distance (up to 10 km) single-mode
fiber links.
Specifications
Optical Specifications
Output ports
Output wavelength
Spectral width (typ) (FWHM)
Output power
Fiber size
Output connector
Emitter classification
Stability
OLS 1-1C
OLS 1-2C
2
2
660 nm- red
850 + 35/-40 nm 850 + 35/-40 nm 1300 +50/-10 nm
30 nm
40 nm
40 nm
120 nm
-10 dBm*
>-20 dBm
>-20 dBm
>-20 dBm
1000 μm, 62.5 μm**
62.5 μm**
ST
ST
Class 1 (IEC 60825 - 1)
± 0.1 dB over 8 hours (after 5 min. warm-up)
General Specifications
Power
Operating temperature
Storage temperature
Size (H x W x D)
Weight
Typical 60 hours with 9V battery, optional AC adapter
-10 to 50°C
-30 to 60°C
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
0.65 lb (.29 kg)
* -10 dBm output is into 1000 micron fiber.
* * May be used to test 50 or 62.5 μm fiber with supplied mandrels.
All specifications at 25°C
Ordering Information
Model
Includes
All OLS 1 models
Protective rubber boot, 9V battery, 50 and 62.5 μm mandrels, manual, and carrying
case.
© 2004-2007, AFL Telecommunications, all rights reserved. OLS4-11-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
19
OLS1-Dual LED Light Source
The OLS1-Dual from AFL Telecommunication is a handheld, rugged LED light source
designed for performing insertion loss measurements on multimode fiber optic links when
used with an optical power meter. The LED output is stabilized to ensure accurate test
results per current TIA/EIA requirements.
The OLS1-Dual features 850 nm and 1300 nm LED output from a single output port and is
easy to operate with only a power button and a wavelength select button. Each wavelength
may be transmitted individually at CW or with Wave ID. When transmitting with Wave ID,
the OLS1-Dual supports transmitting pairs of wavelengths in an alternating pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength(s) along with battery
charge status and external power presence.
Features
•• Handheld, rugged, lightweight
•• Dual wavelengths from a single port
•• Dual or single Wave ID, CW
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
The output port is equipped with UCI based removable adapters to allow the output connectors to be inspected and cleaned. The OLS1-Dual offers long battery life from common
AA alkaline batteries with external AC adapter available as an option.
The OLS1-Dual is fully N.I.S.T. traceable.
Specifications
Optical
OLS1-Dual (single port)
Wavelength
850 ±30 nm
Emitter type
1300 +50/-10 nm
LED, Class I (IEC 60825 - 1)
Spectral width
40 nm (typ)
120 nm (typ)
Output power
>-20 dBm*
Output stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
62.5 µm**
Fiber size
Applications
General
•• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300 nm application, including Gigabit Ethernet (GBE) per
TIA/EIA standards
•• The 1300 nm output can also be used to
test short distance (up to 10 km) singlemode fiber links
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Available adapters
SC, FC, ST
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped jumper is used instead of a 62.5 µm
mandrel-wrapped jumper.
** May be used to test 50 or 62.5 μm fiber with supplied mandrels.
All specifications at 25°C.
Ordering Information
Model
Includes
OLS1-Dual
OLS1-Dual optical light source, protective rubber boot, 2 x AA batteries,
mandrels, user’s guide, and carry case.
© 2004-2007, AFL Telecommunications, all rights reserved. LS1D-30-2000 Revision B, 12.20.07
Specifications are subject to change without notice.
20
OLS2-Dual Laser Light Source
The OLS2-Dual from AFL Telecommunications is a handheld, rugged laser source designed
for performing insertion loss measurements on single-mode fiber optic links when used
with an optical power meter. When paired with an optical fiber identifier, the OLS2-Dual
may be used for fiber identification. The LASER output is stabilized to ensure accurate test
results per current TIA/EIA requirements.
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
Features
•• Handheld, rugged, lightweight
•• Dual wavelengths from a single port
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned. The OLS2-Dual offers long battery life from
common AA alkaline batteries with external AC adapter available as an option.
The OLS2-Dual is fully N.I.S.T. traceable.
Specifications
Optical
OLS2-Dual (single port)
Wavelength
1310 ±20 nm
Emitter type
1550 ±20 nm
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1)
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
Ordering Information
Model
Includes
OLS2-Dual
OLS2-Dual optical light source, protective rubber boot, 2 x AA batteries, user’s
guide, and carry case.
© 2004-2007, AFL Telecommunications, all rights reserved. LS2D-20-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
21
OLS4 Integrated Laser and LED Source
The OLS4 from AFL Telecommunication is a handheld, rugged, integrated two-port
LED and LASER light source designed for performing insertion loss measurements on
multimode or single-mode fiber optic links when used with an optical power meter. When
paired with an optical fiber identifier, the OLS4 may be used for fiber identification. The
LED and LASER outputs are stabilized to ensure accurate test results per current TIA/EIA
requirements.
The OLS4 features 850/1300 nm LED output from a multimode output port and
1310/1550 nm LASER output from a single-mode output port. Each wavelength may be
transmitted individually at CW or with user selectable modulated Tone (SM output). Also,
each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the
OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength(s) along with battery charge
status and external power presence.
Features
•• Handheld, rugged, lightweight
•• Integrated LED and Laser light source
•• Dual wavelengths from a single port
•• Dual or single Wave ID, CW, Tone (SM
output)
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Certify multimode and single-mode links
per TIA/EIA standards
•• Fiber identification prior to splicing
Both output ports are equipped with UCI based removable adapters to allow the output
connectors to be inspected and cleaned. The OLS4 coffers long battery life from common
AA alkaline batteries with external AC adapter available as an option.
The OLS4 is fully N.I.S.T. traceable.
Specifications
Optical
Wavelength
Emitter type
MM Optical Port
850 ± 30 nm 1300 -10/+50 nm
LED, Class I (IEC 60825 - 1)
Spectral width
Output power
Output Stability
40 nm (typ)
120 nm (typ)
> - 20 dBm, 62.5 µm multimode*
± 0.1 dB over 8 hours
(after 5 min. warm-up)
General
Power
SM Optical Port
1310 ± 20 nm
1550 ± 20 nm
Laser, Class I (FDA 21 CFR 1040.10 and
1040.11, and IEC 60825-1)
5 nm (max)
5 nm (max)
0 dBm, 9 µm single-mode
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Typical 72 hours, minimum 40 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped jumper is used instead of a 62.5 µm
mandrel-wrapped jumper.
All specifications at 25°C.
Ordering Information
Model
Includes
OLS4
OLS4 optical light source, protective rubber boot, 2 x AA batteries, mandrels, user’s
guide, and carry case.
© 2004-2007, AFL Telecommunications, all rights reserved. OLS4-11-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
22
OLS7-FTTH & OLS7-3
Triple Wavelength Laser Sources
The OLS7-FTTH and OLS7-3 from AFL Telecommunications are handheld, rugged laser
sources designed for performing insertion loss measurements on single-mode fiber optic
links when used with an optical power meter. When paired with an optical fiber identifier,
both models may be used for fiber identification. The LASER output is stabilized to ensure
accurate test results per current TIA/EIA requirements.
Features
•• Handheld, rugged, lightweight
•• Triple wavelengths from a single port
•• Triple, dual, or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T. Traceable
Applications
•• Passive Optical Networks (PON) testing
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
The OLS7-FTTH and OLS7-3 feature a triple wavelength LASER output from a single
port and are easy to operate. Each wavelength may be transmitted individually at CW
or with user selectable modulated Tone. Also, each wavelength may be transmitted with
Wave ID. When transmitting with Wave ID, the OLS7 will also support transmitting pairs
of wavelengths in an alternating pattern and triple wavelengths in a sequential pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength wavelength(s) along
with battery charge status and external power presence.
The OLS7-FTTH model is designed specifically for today’s FTTH network architectures
featuring a triple wavelength LASER output from a single port: 1310nm output for testing
in the upstream direction and 1490 or 1550nm, for testing in the downstream direction.
The OLS7-3 model features 1310/1550/1625 nm triple wavelength LASER output that is
used for single-mode applications, such as Telecom or CATV.
The OLS7-FTTH & OLS7-3 output ports are equipped with UCI based removable adapters
to allow the output connectors to be inspected and cleaned. Both models offer long battery
life from common AA alkaline batteries with external AC adapter available as an option.
The OLS7 is fully N.I.S.T. traceable.
Specifications
Optical
Wavelength (±20 nm)
Emitter type
Spectral width
Output power
Output stability
OLS7-FTTH OLS7-FTTH optical light source,
protective rubber boot, 2 x AA
batteries, user’s guide, and carry case.
Tone output
OLS7-3
Available adapters
Power
Battery life
Operating temperature
Storage temperature
Size (H x W x D)
Weight
OLS7-3 optical light source, protective
rubber boot, 2 x AA batteries, user’s
guide, and carry case.
Model OLS7-FTTH
Model OLS7-3
1310 nm
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11)
5 nm
3 nm
5 nm
5 nm
5 nm
2 nm
-5 dBm (typical) into 9/125 fiber
± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hours (after 15 min warm-up, after 30 sec typical)
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Models OLS7-FTTH & OLS7-3
SC FC, ST, LC
2 x AA batteries, optional AC adapter
Typical 72 hours (with one laser active), minimum 40 hours
-10° to 50°C, 90% RH (non-condensing)
-30° to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.3 kg (0.66 lb)
All specifications at 25°C.
© 2006-2007, AFL Telecommunications, all rights reserved. OLS7-00-2000 Revision B, 12.20.07
Specifications are subject to change without notice.
23
CKM-2 Contractor Series Multimode
Test Kit with Set Reference
Combining the CSM1-2 optical power meter and CSS1-MM Dual LED light source, the
CMK-2 is a cost-effective test kit designed for performing insertion loss measurements
on multimode fiber optic links. Weighing only 0.4 lb each, both units are compact and
convenient for field use.
Features
•• Palm-sized, rugged, lightweight
•• CW and modulated Tone
•• 270, 330, 1000, 2000 Hz Tone
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Large LCD with backlight
•• Automatic power-off function
•• Battery gauge
•• Long battery life with AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300 nm application, including Gigabit Ethernet (GBE), per
TIA/EIA standards
•• Fiber identification prior to splicing
The CSS1-MM Dual light source features 850 nm and 1300 nm LED output from a single
output port and offers 2 modes of operation, continuous wave (CW) and user selectable
modulated Tone. The LED output is stabilized to ensure accurate test results per current
TIA/EIA requirements and equipped with a fixed SC connector. A large LCD display with
backlight shows emitted wavelengths [nm], tone frequency [Hz], and indicates a low
battery condition.
The CSM1-2 optical power meter operates at 850/ 1300/ 1310/ 1550 nm and features
multiple test Tone detection for fiber identification. The CSM1-2 stores optical references
for each calibrated wavelength. A large LCD display with backlight shows measured power
[dBm or µW] or insertion loss [dB], calibrated wavelengths [nm], tone frequency [Hz],
and indicates a low battery condition. The CSM1 optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements. One adapter cap, 2.5 mm Universal, is included.
Both units offer a five-minute auto-off feature and long battery life from common AA
alkaline batteries.
The CSM1-2 and CSS1-MM are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
CKM-2
CSS1-MM dual optical light source, CSM1-2 optical power meter, AA batteries, 2.5 mm Universaladapter cap, 50 and 62.5 µm mandrels, user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a
variety of connector styles and fiber types and adapter caps for most common connectors may be purchased
from AFL Telecommunications.
The CKM-2 kits may be packed with one of cleaning kit options (purchased separately) as follows:
Model
Description Includes
8500-20-0900 Wet Cleaning Kit 8500-10-0016, Cletop -SB
CCTS-25-0900, Connector Cleaning Tips for 2.5mm ferrule in adapters or
sockets (SC, FC, ST in adaptors).Blue (40 sticks per tube). Qty = 2 tubes
FCC2-00-0900, Optical Quality Cleaning Fluid for fiber connector end faces.
8500-20-0901 Dry Cleaning Kit 8500-10-0016, Cletop -SB
8500-10-0024 ACT-01 2.5mm adapter cleaning tips – Qty = 200
continued on the next page
© 2006-2007, AFL Telecommunications, all rights reserved. CKM2-00-2000 Revision B, 12.07.07
Specifications are subject to change without notice.
24
CKM-2 Contractor Series Multimode Test Kit with Set Reference
CSS1-MM Specifications
Optical
CSS1-MM (single port)
Output wavelength
850 nm ±20 nm
1300 nm +40/-60 nm
Spectral width (max)
35 nm
170 nm
Output power
-20.0 dBm into 62.5/125 fiber
Emitter type
LED, Class I (IEC 60825 - 1)
Output stability
± 0.1 dB over 1 hour (after 30 sec typically)
± 0.15 dB over 8 hours (after 30 sec typically)
Tone output
270, 330, 1000, 2000 Hz
General
Output connector
SC
Power
2 x AA batteries
Battery life
30 hours typical
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
All specifications at 25°C.
CSM1-2 Specifications
Optical
CSM1-2
Calibrated wavelengths
850, 1300, 1310, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850 nm
Accuracy*
± 0.3 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
> 300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
*Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2007, AFL Telecommunications, all rights reserved. CKM2-00-2000 Revision B, 12.07.07
Specifications are subject to change without notice.
25
CKSM-2 Contractor Series Multimode &
Single-mode Test Kit with Set Reference
Combining the CSM1-2 optical power meter, CSS1-MM Dual LED light source, and
CSS1-SM Dual LASER source, the CKSM-2 is a cost-effective test kit designed for
performing insertion loss measurements on multimode as well as single-mode fiber optic
links. Weighing only 0.4 lb each, units are compact and convenient for field use.
Features
•• Palm-sized, rugged, lightweight
•• CW and modulated Tone
•• 270, 330, 1000, and 2000 Hz Tone
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Large LCD with backlight
•• Automatic power-off function
•• Battery gauge
•• Long battery life with AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Certify multimode and single-mode fiber
links per TIA/EIA standards
•• Fiber identification prior to splicing
The CSS1-MM and CSS1-SM sources feature Dual output, 850 /1300 nm LED or
1310/ 1550 nm LASER respectively, from a single output port. Both CSS1 models offer
2 modes of operation, continuous wave (CW) and user selectable modulated Tone. The
CSS1-MM LED and CSS1-SM LASER output ports are stabilized to ensure accurate
test results per current TIA/EIA requirements.A large LCD display with backlight shows
emitted wavelengths [nm], tone frequency [Hz], and indicates a low battery condition. The
CSS1-MM model output port is equipped with a fixed SC connector while the CSS1-SM
output port is equipped with Universal Connector Interface (UCI) base and SC adapter.
The CSM1-2 optical power meter operates at 850/ 1300/ 1310/ 1550 nm and features
multiple test Tone detection for fiber identification. The CSM1-2 stores optical references
for each calibrated wavelength. A large LCD display with backlight shows measured power
[dBm or µW] or insertion loss [dB], calibrated wavelengths [nm], tone frequency [Hz],
and indicates a low battery condition. The CSM1 optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements. One adapter cap, 2.5 mm Universal, is included.
The CSS1-MM, CSS1-SM, and CSM1-2 are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
CKSM-2 CSS1-MM Dual LED source, CSS1-SM Dual Laser souce, CSM1-2 optical power meter, AA batteries,
2.5 mm universal adapter cap, UCI-SC connector, 50 and 62.5 µm mandrels, user's guide, and carry
case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a
variety of connector styles and fiber types and adapter caps for most common connectors may be purchased
from AFL Telecommunications. The CKSM kits may be packed with one of cleaning kit options (purchased
separately) as follows:
Model
Description Includes
8500-20-0900 Wet Cleaning Kit 8500-10-0016, Cletop -SB
CCTS-25-0900, Connector Cleaning Tips for 2.5mm ferrule in adapters or
sockets (SC, FC, ST in adaptors).Blue (40 sticks per tube). Qty = 2 tubes
FCC2-00-0900, Optical Quality Cleaning Fluid for fiber connector end faces.
8500-20-0901 Dry Cleaning Kit 8500-10-0016, Cletop -SB
8500-10-0024 ACT-01 2.5mm adapter cleaning tips – Qty = 200
continued on the next page
© 2006-2007, AFL Telecommunications, all rights reserved. CKSM-20-2000 Revision B, 12.07.07
Specifications are subject to change without notice.
26
CKSM-2 Contractor Series Multimode & Single-mode Test Kit with Set Reference
CSS1-SM Specifications
CSS1-MM Specifications
Optical
CSS1-SM (single port)
Optical
Output wavelength
1310 nm ±20 nm, 1550 nm ±20 nm
Output wavelength
850 nm ±20 nm
1300 nm +40/-60 nm
Spectral width (max)
5 nm
Spectral width (max)
35 nm
170 nm
Output power
0.0 dBm into 9/125 fiber
Output power
Emitter type
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1)
Emitter type
Output stability
± 0.05 dB typical over 1 hour (after 30 sec. )
± 0.15 dB over 8 hours (after 30 sec. typically)
Output stability
Tone output
270, 330, 1000, 2000 Hz
Tone output
General
General
Output connector
SC, FC, ST, LC
Output connector
Power
2 x AA batteries
Power
Battery life
75 hours typical
Battery life
CSS1-MM (single port)
-20.0 dBm into 62.5/125 fiber
LED, Class I (IEC 60825 - 1)
± 0.1 dB over 1 hour (after 30 sec typically)
± 0.15 dB over 8 hours (after 30 sec typically)
270, 330, 1000, 2000 Hz
SC
2 x AA batteries
30 hours typical
Operating temperature -10 to 50°C, 90% RH (non-condensing)
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
Weight
All specifications at 25°C.
0.18 kg (0.4 lb)
All specifications at 25°C.
CSM1-2 Specifications
Optical
CSM1-2
Calibrated wavelengths 850, 1300, 1310, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850 nm
Accuracy*
± 0.3 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
> 300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
11.4 x 6.4 x 3.2 cm (4.5 x 2.5 x 1.3 in)
Weight
0.18 kg (0.4 lb)
*Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2007, AFL Telecommunications, all rights reserved. CKSM-20-2000 Revision B, 12.07.07
Specifications are subject to change without notice.
27
MLP1 Fiber Optic Loss Test Kits
The MLP1 test kits are inexpensive solutions for testing multimode and single-mode
systems. By joining the OPM 1 optical power meter and the OLS1 optical light source, the
MLP1 is a great kit for beginners or network owners. Two versions of the MLP1 test kit
are available for testing Premises networks, LAN, and Gigabit Ethernet. The MLP1-1S test
kit includes the OPM1-2C power meter and OLS1-1C light source. The MLP1-2 test kit
combines the OPM1-2C optical power meter and OLS1-2C optical light source
Features
• Multimode and Single-mode testing
• Loss measurements at 850 and 1300nm
• Includes 50 and 62.5 µm mandrels
• Field portable, battery operated
• Certify 50 or 62.5 µm multimode fiber
links for any 850 or 1300nm application,
including Gigabit Ethernet (GBE)
• N.I.S.T. traceable
Ordering Information
Specifications
Model
Optical Light Source
Output ports
Output wavelength
MLP1-2
OLS1-2C
2
2
660 nm - red 850 + 35/-40nm 850 + 35/-40 nm 1300 + 50/-10 nm
Spectral width (typ) (FWHM)
Output power
Stability (@25°C, 5 min. warm-up)
Fiber size
30 nm
40 nm
40 nm
120 nm
-10 dBm*
>-20 dBm
-20 dBm
>-20 dBm
0.1 dB over 8 hours
0.1 dB over 8 hours
1000 µm, 62.5 µm**
62.5 µm**
Emitter type
Class 1 (IEC 60825 - 1)
Power
Typical 60 hours with 9V battery, optional AC adapter
Connector
Model
Includes
Size (H x W x D)
All MLP1
models
Optical light source, optical power
meter, protective rubber boots,
adapter cap, 50 and 62.5µm mandrels, user’s guide, and carrying case.
Weight
Test jumpers and connector adapters are required for
operation (purchased separately). Test jumpers with a variety
of connector styles and fiber types are available. Adapter
caps for most common connectors may be purchased from
AFL Telecommunications.
MLP1-1S
OLS1-1C
ST
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
0.65 lb (.29 kg)
* -10 dBm output is into 1000 micron fiber.
* * May be used to test 50 or 62.5 μm fiber with supplied mandrels.
Optical Power Meter
OPM1-2C
Calibration wavelength
850, 1300, 1310, 1550 nm
Detector type
Germanium (Ge)
Dynamic range
+6 to -60 dBm
Accuracy (@ 25°C & -10.0 dBm)
±0.25 dB
Measurement units
dBm
Power
Typical 60 hours with 9V battery
Adapter caps
order separately (ST, SC, FC, and others available)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
General Kit Specifications
Dynamic range:
Multimode ( 62.5/125 µm)
Single-mode ( 9/125 µm)
Weight
MLP1-1S
MLP1-2
40 dB @ 850 nm
40 dB @ 850 & 1300 nm
20 dB @ 1300 nm
2. 9 lbs (1.3 kg)
Dimensions (H x W x D)
9.2 x 13.4 x 4.2 in (23.4 x 34 x 10.7 cm)
Operating temperature
-10 to 50°C
Storage temperature
-30 to 60°C
All specifications at 25°C
© 2002, AFL Telecommunications, all rights reserved. MLP1-01-2000 Revision N, 6.16.05
Specifications are subject to change without notice.
28
MLP4-2 Multimode Test Kit with Wave ID
and Set Reference
The MLP4-2 test kit combines the OPM4-2D optical power meter and OLS1-Dual LED light
source and is ideally suited for testing multimode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW
•• Large LCD with backlight (OPM4-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS1-Dual features 850 and 1300 nm LED output from a single output port and is
easy to operate with only a power button and a wavelength select button. Each wavelength
may be transmitted individually at CW or with Wave ID. When transmitting with Wave
ID, the OLS1-Dual supports transmitting pairs of wavelengths in an alternating pattern.
Associated with each operating condition, the designated LED indicator will illuminate to
identify the currently enabled operating mode and emitted wavelength(s) along with battery
charge status and external power presence. The OLS1-Dual output port is equipped with
UCI based removable adapters to allow the output connectors to be inspected and cleaned.
The OPM4-2D features automatic wavelength identification and switching (Wave ID) when
used with the OLS1-Dual and stores optical references for each calibrated wavelength. A
large dual-wavelength LCD display with backlight shows measured power [dBm or µW] or
insertion loss [dB], calibrated wavelengths [nm], wavelength ID, and estimated remaining
battery life. The OPM4-2D optical input port accepts a variety of Noyes thread-on style
adapter caps (ordered separately) to meet a wide range of testing requirements.
The OPM4-2D and OLS1-Dual offer long battery life from common AA alkaline batteries.
The MLP4-2 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode fiber links per TIA/EIA standards
•• The 1300 nm output can also be used to test short distance (up to 10 km) single-mode
fiber links
Ordering Information
Model
Includes
MLP4-2
OLS1-Dual optical light source, OPM4-2D optical power meter, AA batteries, protective rubber
boots, adapter cap, 50 and 62.5 µm mandrels, user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2007, AFL Telecommunications, all rights reserved. MLP4-30-2000 Revision B, 12.20.07
Specifications are subject to change without notice.
29
MLP4-2 Multimode Test Kit with Wave ID and Set Reference
OLS1-Dual specifications
Optical
OLS1-Dual (single port)
Wavelength
850 ±30 nm
Emitter type
1300 +50/-10 nm
LED, Class I (IEC 60825 - 1)
Spectral width
40 nm (typ)
120 nm (typ)
Output power
>-20 dBm*
Output stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
62.5 µm**
Fiber size
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Available adapters
SC, FC, ST
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped jumper is used instead of a 62.5 µm mandre
wrapped jumper.
** May be used to test 50 or 62.5 μm fiber with supplied mandrels.
All specifications at 25°C.
OPM4-2D specifications
Optical
OPM4-2D
Calibrated wavelengths
850, 1300,1310, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 for 850 nm
Wavelength ID range
+6 to -50 dBm
+6 to -45 dBm for 850 nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2007, AFL Telecommunications, all rights reserved. MLP4-30-2000 Revision B, 12.20.07
Specifications are subject to change without notice.
30
MLP5-2 Multimode Test Kit with Wave ID,
Set Reference, and Data Storage
The MLP5-2 test kit combines the OPM5-2D optical power meter and OLS1-Dual LED
light source and is ideally suited for testing multimode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW
•• Large LCD with backlight (OPM5-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS1-Dual features 850 and 1300 nm LED output from a single output port and
is easy to operate with only a power button and a wavelength select button. Each
wavelength may be transmitted individually at CW or with Wave ID. When transmitting
with Wave ID, the OLS1-Dual supports transmitting pairs of wavelengths in an alternating
pattern. Associated with each operating condition, the designated LED indicator will
illuminate to identify the currently enabled operating mode and emitted wavelength(s)
along with battery charge status and external power presence. The OLS1-Dual output
port is equipped with UCI based removable adapters to allow the output connectors to be
inspected and cleaned.
The OPM5-2D features automatic wavelength identification and switching (Wave ID) when
used with the OLS1-Dual and stores optical references for each calibrated wavelength
and up to 500 records per wavelength of power or insertion loss measurements. Using
the supplied Windows® compatible software and USB connection, test records are
transferred to a PC for analysis, printing, and storage. A large dual-wavelength LCD
display with backlight shows measured power [dBm or µW] or insertion loss [dB],
calibrated wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining
battery life. The OPM5-2D optical input port accepts a variety of Noyes thread-on style
adapter caps (ordered separately) to meet a wide range of testing requirements.
The OLS1-Dual and OPM5-2D offer long battery life from common AA alkaline batteries
with external AC adapter available as an option.
The MLP5-2 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode fiber links per TIA/EIA standards
•• The 1300 nm output can also be used to test short distance (up to 10 km) single-mode
fiber links
Ordering Information
Model
Includes
MLP5-2
OLS1-Dual optical light source, OPM5-2D optical power meter, AA batteries, protective rubber
boots, adapter cap, USB cable, Windows® compatible software and user's guide, 50 and 62.5 µm
mandrels, MLP5-2 test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2007, AFL Telecommunications, all rights reserved. MLP5-30-2000 Revision B, 12.20.07
Specifications are subject to change without notice.
31
MLP5-2 Multimode Test Kit with Wave ID, Set Reference, and
Data Storage
OLS1-Dual specifications
Optical
OLS1-Dual (single port)
Wavelength
850 ±30 nm
Emitter type
1300 +50/-10 nm
LED, Class I (IEC 60825 - 1)
Spectral width
40 nm (typ)
120 nm (typ)
Output power
>-20 dBm*
Output stability
± 0.1 dB over 8 hours (after 5 min. warm-up)
62.5 µm**
Fiber size
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 30 hours, minimum 20 hours
Available adapters
SC, FC, ST
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50 µm mandrel-wrapped jumper is used instead of a
62.5 µm mandrel-wrapped jumper.
** May be used to test 50 or 62.5 μm fiber with supplied mandrels.
All specifications at 25°C.
OPM5-2D specifications
Optical
OPM5-2D
Calibrated wavelengths
850, 1300, 1310,1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Wavelength ID range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries, optional AC adapter
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2007, AFL Telecommunications, all rights reserved. MLP5-30-2000 Revision B, 12.20.07
Specifications are subject to change without notice.
32
SLP4-6D Single-mode Test Kit with
Wave ID and Set Reference
The SLP4-6D test kit combines the OPM4-4D optical power meter and OLS2-Dual LASER
light source and is ideally suited for testing single-mode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Large LCD with backlight (OPM4-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned.
The OPM4-4D features automatic wavelength identification and switching (Wave ID) when
used with the OLS2-Dual, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-4D and OLS2-Dual offer long battery life from common AA alkaline batteries.
The SLP4-6D test kit is fully N.I.S.T. traceable.
Applications
•• Certify single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SLP4-6D
OLS2-Dual optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-6D test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2007, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
33
SLP4-6D Single-mode Test Kit with Wave ID and Set Reference
OLS2-Dual specifications
Optical
OLS2-Dual (single port)
Wavelength
1310 ±20 nm
Emitter type
1550 ±20 nm
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1)
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
OPM4-4D specifications
Optical
OPM4-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 for 850 nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850 nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2007, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
34
SLP4-7 Triple Wave Test Kit with Wave
ID and Set Reference
Triple wavelength single-mode test kits are available in two models, SLP4-7 or SLP4FTTH. The SLP4-7 and SLP4-FTTH model combine the OPM 4-4D optical power meter and
either OLS7-3 (1310/1550/1625 nm) or OLS7-FTTH (1310/1490/1550 nm) LASER source
respectively.
Features
• Rugged, handheld, lightweight
• Designed for field use
• Wave ID - automatic wavelength identification and switching
• Triple Wave ID, dual Wave ID, single
Wave ID, CW, and modulated Tone
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone
• Large LCD with Backlight
• Power measurements in dBm or μW;
insertion loss in dB
• Reference power level storage
• AA alkaline, optional rechargeable NiMH
battery pack or AC adapter
• Low battery indicator
• Cost-effective, easy to use
• N.I.S.T traceable
Applications
• Passive Optical Networks (PON) testing
• Certify single-mode links per TIA/EIA
standards
• Modulation Tone mode for fiber identification to isolate specific fibers in a
bundle prior to splicing or rerouting
The OLS7 features triple wavelength LASER output from a single output port and is easy
to operate. The LASER output is stabilized to ensure accurate test results per current
TIA/EIA requirements. Each wavelength may be transmitted individually at CW or with tone
modulation at frequencies of 270Hz, 330Hz, 1kHz and 2kHz. Also, each wavelength may
be transmitted with Wave ID. When transmitting with Wave ID, the OLS7 will also support
transmitting pairs of wavelengths in an alternating pattern and triple wavelengths in a
sequential pattern. The OLS7 output port is equipped with a UCI based removable adapter
to allow the output connector to be inspected and cleaned.
The OPM 4-4D offers Wave ID, automatic wavelength identification and switching, when
used with the OLS7. Multiple test Tone detection is provided for fiber identification. The
OPM 4-4D stores optical references for each calibrated wavelength. An easy to read Dual
Wavelength LCD display with Backlight shows measured power [dBm or µW] or insertion
loss [dB], calibrated wavelengths, tone signal [Hz], wavelength ID, and the battery charge
status. The OPM 4-4D optical input port accepts Noyes thread-on style adapter caps.
Adapter caps are required for operation and must be ordered separately.
In addition to being powered by two AA alkaline, the OPM 4-4D or OLS7 can be powered
by optional AC adapter and/or rechargeable NiMH battery pack.
The OPM 4-4D and OLS7 are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP4-7
OLS7-3 optical light source, OPM 4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, user's guide, and carry case.
SLP4-FTTH
OLS7-FTTH optical light source, OPM 4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2006, AFL Telecommunications, all rights reserved. SLP4-07-2000 Revision 1A, 5.05.06
Specifications are subject to change without notice.
35
SLP4-7 Triple Wave Test Kit with Wave ID and Set Reference
OLS7 Specifications
Optical
Model OLS7 - FTTH
Wavelength (±20 nm)
Spectral width
Model OLS7
1310 nm
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
5 nm
3 nm
5 nm
5 nm
5 nm
2 nm
Output power
-5 dBm (typical) into 9/125 fiber
Emitter type
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11)
Output stability
± 0.05 dB over 1 hr. (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hrs (after 15 min warm-up, after 30 sec typical)
Connectors
UCI based adapters: SC standard, FC & ST available, LC optional
Tone output
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Models OLS7 - FTTH & OLS7
Power
2 AA alkalines. Optional: NiMH rechargeables or external AC adapter
Battery life
Minimum 85 hours (with one laser active)
Operating temp.
-10° to 50°C, 90% RH (non-condensing)
Storage temp.
-30° to 60°C, 90% RH (non-condensing)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.66 lb (0.3 kg)
All specifications at 25°C
OPM 4-4D specifications
Optical
OPM 4-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850 nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries, optional NiMH
Battery life (2 x AA)
300 hours with backlight [Off]
20 hours with backlight [On]
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006, AFL Telecommunications, all rights reserved. SLP4-07-2000 Revision 1A, 5.05.06
Specifications are subject to change without notice.
36
SLP5-6D Single-mode Test Kit with Wave
ID, Set Reference, and Data Storage
The SLP5-6D test kit combines the OPM5-4D optical power meter and OLS2-Dual LASER
light source and is ideally suited for testing single-mode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Large LCD with backlight (OPM5-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned.
The OPM5-4D features automatic wavelength identification and switching (Wave ID) when
used with the OLS2-Dual, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength and up to 500 records per wavelength of
power or insertion loss measurements. Using the supplied Windows® compatible software
and USB connection, test records are transferred to a PC for analysis, printing, and
storage. A large dual-wavelength LCD display with backlight shows measured power [dBm
or µW] or insertion loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID,
and estimated remaining battery life. The OPM5-4D optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements.
The OPM5-4D and OLS2-Dual offer long battery life from common AA alkaline batteries
with external AC adapter available as an option.
The SLP5-6D test kit is fully N.I.S.T. traceable.
Applications
•• Certify single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SLP5 -6D
OLS2-Dual optical light source, OPM5-4D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, SLP5-6D test kit user's
guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2007, AFL Telecommunications, all rights reserved. SLP5-30-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
37
SLP5-6D Single-mode Test Kit with Wave ID, Set Reference,
and Data Storage
OLS2-Dual specifications
Optical
OLS2-Dual (single port)
Wavelength
1310 ±20 nm
Emitter type
1550 ±20 nm
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1)
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
OPM5-4D specifications
Optical
OPM5-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
± 0.25 dB
Accuracy*
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries, optional AC adapter
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2007, AFL Telecommunications, all rights reserved. SLP5-30-2000 Revision C, 12.20.07
Specifications are subject to change without notice.
38
SLP5-7 Triple Wave Test Kit with Wave
ID and Set Reference and Data Storage
The SLP5-7 test kit combines the OPM 5-4D optical power meter and OLS7-3 LASER
source and is ideally suited for testing single-mode fiber optic networks .
Features
• Rugged, handheld, lightweight
• Designed for field use
• Wave ID - automatic wavelength identification and switching
• Triple Wave ID, dual Wave ID, single
Wave ID, CW, and modulated Tone
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone
• Adjustable output
• Large LCD with Backlight
• Power measurements in dBm or μW;
insertion loss in dB
• Reference power level storage
• Up to 500 test records per wavelength
storage and download
• USB port for download of stored records
• AA alkaline, optional rechargeable NiMH
battery pack or AC adapter
• Low battery indicator
• Free Windows® compatible software to
view, print, and archive test records
• Cost-effective, easy to use
• N.I.S.T traceable
Applications
• Certify single-mode links per TIA/EIA
standards
• Modulation Tone mode for fiber identification to isolate specific fibers in a
bundle prior to splicing or rerouting
The OLS7-3 features 1310/1550/1625 nm triple wavelength LASER output from a single
output port and is easy to operate. The LASER output is stabilized to ensure accurate test
results per current TIA/EIA requirements. Each wavelength may be transmitted individually
at CW or with tone modulation at frequencies of 270Hz, 330Hz, 1kHz and 2kHz. Also, each
wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the OLS7-3
will also support transmitting pairs of wavelengths in an alternating pattern and triple
wavelengths in a sequential pattern. The OLS7-3 output port is equipped with a UCI based
removable adapter to allow the output connector to be inspected and cleaned.
The OPM 5-4D offers Wave ID, automatic wavelength identification and switching, when
used with the OLS7-3 light source. Multiple test Tone detection is provided for fiber
identification. The OPM 5-4D stores optical references for each calibrated wavelength.
An easy to read Dual Wavelength LCD display with Backlight shows measured power
[dBm or µW] or insertion loss [dB], calibrated wavelengths, tone signal [Hz], wavelength
ID, and the battery charge status. Up to 500 records per wavelength of power or insertion
loss measurements may be stored in internal non-volatile memory. Using the supplied
Windows® compatible software and USB connection, test records may be transferred to
a PC for storage, display, analysis, and printing. The OPM 5-4D optical input port accepts
Noyes thread-on style adapter caps. Adapter caps are required for operation and must be
ordered separately.
In addition to being powered by two AA alkaline, the OPM 5-4D or OLS7-3 can be powered
by optional AC adapter and/or rechargeable NiMH battery pack.
The OPM 5-4D and OLS7-3 are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP 5 -6D
OLS7-3 optical light source, OPM5-4D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, SLP 5 test kit user's
guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2006, AFL Telecommunications, all rights reserved. SLP5-07-2000 Revision A, 5.05.06
Specifications are subject to change without notice.
39
SLP5-7 Triple Wave Test Kit with Wave ID and Set Reference
and Data Storage
OLS7 Specifications
Optical
Model OLS7 - FTTH
Wavelength (±20 nm)
Spectral width
Model OLS7
1310 nm
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
5 nm
3 nm
5 nm
5 nm
5 nm
2 nm
Output power
-5 dBm (typical) into 9/125 fiber
Emitter type
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11)
Output stability
± 0.05 dB over 1 hr. (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hrs (after 15 min warm-up, after 30 sec typical)
Connectors
UCI based adapters: SC standard, FC & ST available, LC optional
Tone output
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Models OLS7 - FTTH & OLS7
Power
2 AA alkalines. Optional: NiMH rechargeables or external AC adapter
Battery life
Minimum 85 hours (with one laser active)
Operating temp.
-10° to 50°C, 90% RH (non-condensing)
Storage temp.
-30° to 60°C, 90% RH (non-condensing)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.66 lb (0.3 kg)
All specifications at 25°C
OPM 5-4D specifications
Optical
OPM 5-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries, optional NiMH or AC adapter
Battery life (2 x AA)
300 hours with backlight [Off]
20 hours with backlight [On]
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
5.5 x 3.2 x 1.5 in (14.0 x 8.1 x 3.8 cm)
Weight
0.58 lb (0.26 kg)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006, AFL Telecommunications, all rights reserved. SLP5-07-2000 Revision A, 5.05.06
Specifications are subject to change without notice.
40
SLP4 Triple Wave Test Kits with Wave ID
and Set Reference
The SLP4 triple wavelength single-mode test kits are available in two models, SLP4-FTTH
and SLP4-7. The SLP4-FTTH and SLP4-7 model combine the OPM4-4D optical power
meter and either OLS7-FTTH (1310/1490/1550 nm) or OLS7-3 (1310/1550/1625 nm)
LASER source respectively.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Triple, dual, or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM4-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Passive Optical Networks (PON) testing
•• Certify single-mode links per TIA/EIA
standards
•• Fiber identification prior to splicing
The OLS7-FTTH and OLS7-3 feature a triple wavelength LASER output from a single port
and are easy to operate. Each wavelength may be transmitted individually at CW or with
user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID.
When transmitting with Wave ID, the OLS7 will also support transmitting pairs of wavelengths in an alternating pattern and triple wavelengths in a sequential pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength wavelength(s) along with battery charge status and external power presence. The OLS7-FTTH & OLS7-3 output ports
are equipped with UCI based removable adapters to allow the output connectors to be
inspected and cleaned.
The OPM4-4D features automatic wavelength identification and switching (Wave ID)
when used with the OLS7, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-4D and OLS7 offer long battery life from common AA alkaline batteries.
The SLP4-7 and SLP4-FTTH kits are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP4-7
OLS7-3 optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-7 test kit user's guide, and carry case.
SLP4-FTTH
OLS7-FTTH optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-FTTH test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2006-2007, AFL Telecommunications, all rights reserved. SLP4-07-2000 Revision A 12.20.07
Specifications are subject to change without notice.
41
SLP4-7 Triple Wave Test Kit with Wave ID and Set Reference
OLS7 Specifications
Optical
Wavelength (±20 nm)
Emitter type
Spectral width
Output power
Output stability
Model OLS7-FTTH
1310 nm
5 nm
Tone output
Model OLS7-3
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11)
3 nm
5 nm
5 nm
5 nm
2 nm
-5 dBm (typical) into 9/125 fiber
± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hours (after 15 min warm-up, after 30 sec typical)
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Models OLS7-FTTH & OLS7-3
Available adapters
Power
Battery life
Operating temperature
Storage temperature
Size (H x W x D)
Weight
SC FC, ST, LC
2 x AA batteries, optional AC adapter
Typical 72 hours (with one laser active), minimum 40 hours
-10° to 50°C, 90% RH (non-condensing)
-30° to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.3 kg (0.66 lb)
All specifications at 25°C.
OPM4-4D specifications
Optical
OPM4-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
Tone detect range
+26 to -50 dBm
+6 to -30 dBm
+6 to -25 for 850 nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850 nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
Weight
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2007, AFL Telecommunications, all rights reserved. SLP4-07-2000 Revision A 12.20.07
Specifications are subject to change without notice.
42
SLP5 Triple Wave Test Kits with Wave ID,
Set Reference, and Data Storage
The SLP5 triple wavelength single-mode test kits are available in two models, SLP5-FTTH
and SLP5-7. The SLP5-FTTH and SLP5-7 model combine the OPM5-4D optical power
meter and either OLS7-FTTH (1310/1490/1550 nm) or OLS7-3 (1310/1550/1625 nm)
LASER source respectively.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Triple, dual, or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM5-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Cost-effective, easy to use
•• N.I.S.T traceable
Applications
•• Passive Optical Networks (PON) testing
•• Certify SM links per TIA/EIA standards
•• Fiber identification prior to splicing
The OLS7-FTTH and OLS7-3 feature a triple wavelength LASER output from a single port
and are easy to operate. Each wavelength may be transmitted individually at CW or with
user selectable modulated Tone. Also, each wavelength may be transmitted with Wave ID.
When transmitting with Wave ID, the OLS7 will also support transmitting pairs of wavelengths in an alternating pattern and triple wavelengths in a sequential pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength wavelength(s) along with battery charge status and external power presence. The OLS7-FTTH & OLS7-3 output ports
are equipped with UCI based removable adapters to allow the output connectors to be
inspected and cleaned.
The OPM5-4D features automatic wavelength identification and switching (Wave ID)
when used with the OLS7, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM5-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM5-4D and OLS7 offer long battery life from common AA alkaline batteries with
external AC adapter available as an option.
The SLP5-FTTH and SLP5-7 test kits are fully N.I.S.T. traceable.
Ordering Information
Model
Includes
SLP5 -7
OLS7-3 optical light source, OPM5-4D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, SLP5-7 test kit user's
guide, and carry case.
SLP5-FTTH OLS7-FTTH optical light source, OPM5-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, USB cable, Windows® compatible software and user’s guide, SLP5-FTTH test
kit user’s guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately). Test jumpers with a variety of connector
styles and fiber types and adapter caps for most common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2006-2007, AFL Telecommunications, all rights reserved. SLP5-07-2000 Revision A, 12.20.07
Specifications are subject to change without notice.
43
SLP5-7 Triple Wave Test Kit with Wave ID, Set Reference, and
Data Storage
OLS7 Specifications
Optical
Wavelength (±20 nm)
Emitter type
Spectral width
Output power
Output stability
Model OLS7-FTTH
1310 nm
5 nm
Tone output
Model OLS7-3
1490 nm
1550 nm
1310 nm
1550 nm
1625 nm
Laser, Class I (FDA 21 CFR 1040.10 and 1040.11)
3 nm
5 nm
5 nm
5 nm
2 nm
-5 dBm (typical) into 9/125 fiber
± 0.05 dB over 1 hour (after 15 min warm-up, after 30 sec typical)
± 0.1 dB over 8 hours (after 15 min warm-up, after 30 sec typical)
270 Hz, 330 Hz, 1 kHz, 2 kHz
General
Models OLS7-FTTH & OLS7-3
Available adapters
Power
Battery life
Operating temperature
Storage temperature
Size (H x W x D)
Weight
SC FC, ST, LC
2 x AA batteries, optional AC adapter
Typical 72 hours (with one laser active), minimum 40 hours
-10° to 50°C, 90% RH (non-condensing)
-30° to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.3 kg (0.66 lb)
All specifications at 25°C.
OPM5-4D specifications
Optical
OPM5-4D
Calibrated wavelengths
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Wavelength ID range
+6 to -30 dBm
+6 to -25 dBm for 850nm
Accuracy*
± 0.25 dB
Resolution
0.01 dB
Measurement units
dB, dBm, μW
General
Power
2 x AA batteries, optional AC adapter
Battery life
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2006-2007, AFL Telecommunications, all rights reserved. SLP5-07-2000 Revision A, 12.20.07
Specifications are subject to change without notice.
44
OFS 300 Optical Fiber Scope
The Noyes OFS 300 from AFL Telecommunications is a versatile Optical Fiber Scope with
precision 200X magnification. This handheld and rugged scope is used for inspection of
optical fiber connectors for scratches, dirt, or other problems normally associated with
poor transmission performance.
A built-in laser safety filter provides > 40 dB IR protection to reduce risk of injury to the eye if
accidentally viewing an active fiber.* The OFS 300 features a universal adapter cap mount
that accepts a variety of Noyes thread-on style adapter caps (ordered separately) to ease
inspection of many connector style. A momentary power switch located on the top panel
keeps one hand free for focusing.
The OFS 300 offers 60 hours of continuous battery life from standard 2 x AA batteries and
features an LED indicator, which will flash when barriers require replacement.
Features
•• Laser safety filter installed*
•• Precision 200X zoom
•• Universal adapter interface
•• Low battery LED indicator
•• Long battery life with 2 x AA alkaline
•• Tripod mount
•• Rugged, handheld, easy to use
*Always follow your company’s laser safety procedures and never use an optical microscope to view live fiber optic connectors.
Specifications
Optical Specifications
Nominal magnification
Adapter mount
Safety filter
200X
Universal, thread-on
Schott KG3, > 40 dB IR
General Specifications
Operating temperature
0 to +50°C
Storage temperature
-20 to +50°C
Power
2 x AA batteries
Battery life
> 60 hours
Weight in use
0.67 kg (1.5 lbs)
Size (H x W x D)
13 x 5 x 20 cm (5 x 2 x 8 in)
Ordering Information
Model
Includes
OFS 300
OFS 300 Inspection Scope, 2 x AA batteries, neck strap, 2.5 mm universal
adapter cap, and user’s guide
© 2002-2008, AFL Telecommunications, all rights reserved. OFS1-00-2000 Revision T 07.30.08
Specifications are subject to change without notice.
45
VS 300 View Safe Inspection Scope
The VS 300 Video Fiber Scope removes concerns for eye safety while inspecting optical
fiber connectors. The design eliminates the optical path to the eye by utilizing a miniature
camera and a state-of-the-art micro-display that achieves unparalleled clarity and resolution.
The VS 300 is modeled after the functionality of our highly successful OFS 300 product
line with the following improvements:
• The VS 300 has no optical path to the user’s eye.
• The VS 300 has NTSC video output.
• The VS 300 has the familiar shape and control positions of the OFS 300 but is half the
weight and has a molded easy grip case with easy access battery compartment.
Features
• Video Technology
• No optical path to your eye
• 400X magnification
• Resolves ¾ micron scratches
• Universal Adaptor Interface with new
"pan and lock" centering mount
• Video Output
The magnification of the unit is equivalent to 400X (23-degree field of view comparable
to 8” monitor viewed at a distance of 20”) and provides 600X when its video output is
displayed on a 12” monitor. The unit uses all the OFS 300 adaptor caps and has an energy
saving automatic shutoff.
Specifications
Optical Specifications
Magnification
400X equivalent to 8” monitor for 20” distance, 600X on 12” monitor
Adaptor mount
Thread-on (Universal)
Safety filter
Not Required - No optical path to user
Video output
NTSC
General Specifications
Operating temperature
0 to +50°C
Storage temperature
-20 to +60°C
Humidity
0 to 90% (non - condensing)
Power supply
2 AA alkaline batteries, optional AC adapter
Battery life
10 hours continuous
Indicators
Low battery
Weight
0.94 lbs (0.42 kg)
Size (H x W x D)
3.5 x 1.5 x 8.5 in (8.9 x 3.8 x 21.6 cm)
Ordering Information
Model
Includes
VS 300
VS 300 Inspection Scope, 2 x AA batteries, neck strap, 2.5 mm universal adapter cap, and
user’s guide
© 2002, AFL Telecommunications, all rights reserved. VOS3-00-2000 Revision D 8.03.05
Specifications are subject to change without notice.
46
VFS 2 Video Fiber Scope 2nd Generation
The VFS 2 is a small versatile video fiber scope, which retains the superior image quality
associated with Noyes inspection products. The unique “optical-knuckle” allows the user
to orient the probe head in virtually any direction. This feature allows the user to view connectors that may be located in tight or difficult locations. With a probe head length of less
than 8 cm (3.25”), access into crowded/cramped quarters becomes a reality.
The VFS 2 resolves ¾ micron scratches, keeping with our standard of quality end-face
images. This unit is designed for one-handed operation and with the “optical-knuckle”
feature, the unit is equally easy for both right and left handed individuals.
Features:
• Unparalleled access to connectors and
bulkhead adapters
• One-handed operation
• Resolves ¾ micron scratches
• Precision adapter tips for easy centering
• 350-micron field of view (diagonal)
• Smooth, precision focusing (left or right
handed)
• Advanced lithium ion battery
The VFS 2 probe may be paired with the VFS 2 high-resolution 3.5” Display unit.
Also, the VFS 2 Inspection Probe may be used with the VCP 1 Video Capture Port, which
allows the user to inspect fiber optic end-faces and capture viewed images on a PC.
Specifications
Optical specifications
Field of view
350 microns diagonal (208 μm vertical, 285 μm horizontal)
Magnification
250X on 3.5” display
Resolution
¾ micron scratch
Video Output
NTSC
VFS 2 Probe specifications
Operating temperature
0 to +50°C
Storage temperature
-20 to +60°C
Humidity
0 to 90% (non-condensing)
Probe weight
0.4 lb (0.2 kg)
Probe body size (L x W x D)
6.3 x 1.3 x 1.3 in (15.9 x 3.3 x 3.3 cm)
Probe head size (with FC adapter), (L x W x D)
3.1 x 1.0 x 0.6 in (7.9 x 2.5 x 1.5 cm)
VFS 2 Display specifications
Display Screen Size
3.5 inch TFT NTSC
Display package with protective boot size
9.0 x 2.0 x 4.7 in (22.9 x 5.1 x 11.9 cm)
Weight
2 lb (0.9 kg)
Power
Li-Ion battery pack or AC adapter
Battery life with VFS2 probe
> 4 hours
Operating temperature
0° to 50° C
Storage temperature
-20 to +60°C
Humidity
0 to 90% RH non-condensing
Li-Ion battery pack charging temp.
-10 to +45°C
Li-Ion battery pack recharging time
4 hours
Ordering Information
Model
Includes
VFS2-00-0900
VFS2 Probe, VFS 2 LCD Display unit (3.5” (9 cm), AC adapter, and user's guide.
VFS2-00-0903
VFS2 Probe, VCP1 USB interface and basic software (requires computer with display), and
user's guide.
© 2004-2007, AFL Telecommunications, all rights reserved. VFS2-00-2000 Revision B, 5.22.07
Specifications are subject to change without notice.
47
VCP 1 USB Video Capture Port
fiber end images displayed on a PC
The VCP 1 Video Capture Port is an interfacing module that provides high-speed composite
video signal to a digital format conversion for capturing and displaying video data on a PC.
The VCP 1 simply attaches via a standard USB connector to you computer and offers “plug
and play” installation.
When used in conjunction with the VFS 2 probe or VS 300 video microscope, the VCP 1
Video Capture Port allows you to inspect fiber optic end-faces and capture viewed images
on your computer. With the supplied easy-to-use Windows software, fiber end images can
be saved and organized for analyzing, printing, and archiving.
The VCP 1 front panel includes the video capture button - [Snap Shot] for single shot video
capture and the [Active] LED, which indicates that the unit is operating.
Batteries or an AC adapter are not required; the VCP 1 power is supplied via the USB connection. The VCP 1 is ideal for laptop or desktop use.
The VCP 1 package Includes: VCP 1 unit, CD-ROM with driver and software, and user’s
guide.
System Requirements
VCP 1
Features
• Compact size
• Captures fiber end images directly into
your computer
• Includes Includes “Video Capture”- Windows®-based software
• Converts analog video signal from Noyes
RJ11 input to digital via USB A plug
• Supports NTSC or PAL system
• No battery - no need to install batteries
or run off the AC adapter
• Low power consumption
• A single snap shot button takes still
images at VGA solution (640 x 480
pixels)
• Low CPU utilization at decompression
• Plug and play installation
• A 400 MHz (or faster) PC or laptop with
USB 1.1 or better
• At least 800 x 600 SVGA display
• Windows 2000 or XP
• At least 128 MB of RAM
• A CD-ROM drive
Specifications
Interface type
USB
Operating system
Windows 2000 and XP
Video input
Noyes RJ11 connector
Output
USB Standard (VCP 1 is a Twain compatible device using supplied software)
Analog video format
NTSC or PAL
Video capture resolution
640 x 480 pixels
Snap shot
Single button to capture still images at 640 x 480 pixels
Video capture format(s):
JPEG
Power source
5VDC @500 mA (max) through USB port to 6 foot cord
USB data bandwidth
4Mbps - 8Mbps isochronous
Weight
0.25 lb (0.11 kg)
Size (L x W x D)
4.0 x 2.2 x 1.0 in (10.2 x 5.6 x 2.5 cm)
For more information concerning Noyes fiber optic products and accessories please call 1-800-321-5298.
© 2003, AFL Telecommunications, all rights reserved. VCP1-00-2000 Revision 1E 9.12.05
Specifications are subject to change without notice.
48
HiLite and VFI2 Visual Fault Identifiers
VFI 2
The HiLite and VFI 2 are compact but powerful visible red laser sources designed to
troubleshoot faults on fiber optic cables. Light generated by these units will escape from
sharp bends and breaks in jacketed or bare fibers, as well as poorly mated connectors.
They can identify faults in fiber optic jumper cables, distribution frames, patch panels, and
splice trays.
The HiLite and VFI 2 are an excellent complement to an OTDR because they can locate
faults inside the OTDR’s dead-zone. Other applications include end-to-end continuity
checks, identifying connectors in patch panels and fibers during splicing operations. The
universal connector interface provides fast operation with many connector styles without
changing an adapter.
Features
• 650 nm visible red laser source
• Compact size
• Universal connector interface for quick
connection
• High power (1 mW)
Specifications
HiLite
Optical
Emitter type
VFI 2
HiLite
Laser (FDA and IEC Class II)*
Laser (FDA and IEC Class II)*
Wavelength
Output power
Modulation
650 nm ± 10 nm
650 nm ± 10 nm
1 mW (into single-mode fiber)
1 mW (into single-mode fiber)
2 Hz or CW selected
2 Hz
General
Universal adapter (2.5 mm included)
2.5 mm fixed**
2 AA alkaline batteries (60 hours typical)
1 AAA alkaline battery (4 hours typical)
Connector type
Power
Operating temperature
10 to 35°C, 85% humidity non condensing
Storage temperature
Size (H x W x D)
0 to 50°C, 95% humidity non condensing
5.5 x 2.4 x 1.3 in (14.0 x 6.2 x 3.2 cm)
2.8 x 1.4 x 0.6 in (7.0 x 3.6 x 1.5 cm)
7.06 oz (< 200 g)
1.75 oz (50 g)
Weight
* FDA 21 CFR 1040.10 and 1040.11, and IEC 60825-1 amended Q2, 2001.
** Accepts 2.5 mm ferule connectors ( SC, FC, ST, E2000)
Ordering Information
Model
Includes
VFI 2
VFI 2 unit, instruction card, and carrying case.
HiLite
HiLite unit, instruction card, and carrying case.
© 2002, AFL Telecommunications, all rights reserved. VFI3-00-2000 Revision J, 8.17.05
Specifications are subject to change without notice.
49
FTS Series Fiber Optic Talk Sets
FTS 1
FTS 2
Fiber Optic Talk Sets are an inexpensive solution to meet your communication needs when
testing multimode or single-mode fiber optic cables. Designed for voice communication
over spare fibers, they provide full duplex, hands-free operation. Ease of use and compact
size allow the operators to focus on the task at hand, rather than operating the talk set.
Two talk set models are available, the FTS 1 for communication on single-mode or
multimode fiber and the FTS 2 for long-range single-mode applications. The FTS 2 model
includes a multiparty communication feature, which provides the connection of two talk
sets at a common site to extend the range or to include three or more persons in the
conversation.
FTS-20C Clip-on Coupler
A clip-on coupler is available for bare fiber access where terminated ends are not available. The FTS 20C allows bi-directional communication from a center point on the fiber
link or from an unterminated end. When used with a fiber talk set – such as the FTS2
– a user can access the intended talk fiber at a mid-point across the span, usually at the
splice enclosure. The FTS-20C can also be used in conjunction with a Laser Source and
Tone Detector to inject or detect 2 kHz test tones. It works at 1310, 1550, or 1625 nm.
Coupling efficiency is approximately 18 dB.
FTS-20C
Features
• Single fiber, full duplex
• Multimode and single-mode models
• Field portable, hands-free operation
• Automatic connection
• Multiparty communication
• Digital technology
• Call-back feature/ringing (FTS 2)
• Communicates with T500B talk option
(FTS 2)
Ordering Information
Model
Includes
FTS 1
FTS 2
Protective rubber boots, batteries,
headsets, manual, and carry case.
Fiber optic talk sets are purchased in pairs. Two units are
required for communication.
Specifications
Model
Optical Specifications
Wavelength
Dynamic Range MM/SM
Distance Range (km)
Typical 62.5 or 50 µm MM fiber1
Typical 1310 nm-optimized SM fiber2
Typical 1550 nm-optimized SM fiber3
FTS 1-2
FTS 2-1310
FTS 2-1550
1300 nm
1300 nm
1550 nm
12 dB/ 20 dB
45 dB
45 dB
>10
50
40
N/A
113
90
N/A
150
180
Fiber Type
MM/SM
SM
Connector
FC, SC, or ST
FC, SC, or ST
LED
Laser
Class 1 (IEC 60825 - 1)
Class 1 (FDA 21 CFR 1040.10 and
1040.11, and IEC 60825-1)
9V alkaline
4 AA alkaline or AC adapter
Emitter Type
Emitter Classification
General Specifications
Power
Weight in Use
Size (H x W x D)
0.56 lb (.25 kg)
1.16 lb (.52 kg)
6.6 x 3.1 x 1.5 in
(16.8 x 7.9 x 3.8 cm)
7.3 x 4.4 x 1.8 in
(18.5 x 11.1 x 4.6 cm)
Operating Temperature
0° to +50° C, RH 0 to 90% non-condensing
Storage Temperature
-20° to +50° C, RH 0 to 90% non-condensing
Notes:
1 2.8 dB/km @ 850 nm, 0.6 dB/km @ 1300 nm.
2 0.4 dB/km @ 1310 nm, 0.3 dB/km @ 1550 nm.
3 0.5 dB/km @ 1310 nm, 0.25 dB/km @ 1550 nm.
© 2002, AFL Telecommunications, all rights reserved. FTS2-00-2000 Revision H, 9.15.05
Specifications are subject to change without notice.
50
SVA 1 Singlemode Variable Attenuator
The SVA 1 Singlemode Variable Attenuator advances fiber optic field testing by offering
superior performance in a low cost hand-held package. Utilizing a simplified, industry
accepted attenuation technique, the innovative design of the SVA 1 offers superior
resolution across the entire 60 dB dynamic range.
Intended for field testing during installation, new equipment turn-ups, or routine
maintenance, the SVA 1 is a complete, easy to use attenuator. Its unique features allow
bidirectional signal transmission with no loss penalty.
The SVA 1 is available with a variety of connectors and reflectance options to better than
60 dB. With only two adjustments, COARSE and FINE, the SVA 1 is simple to understand
and operate. The SVA 1 is suited for all singlemode applications including Telco, LANs,
WANs, Video, and CATV.
Specifications
Features
Optical Specifications SVA 1
VOA5-MM
• 1310 and 1550 nm single-mode
• Lightweight
• Coarse and fine adjustments
• 60 dB dynamic range
• Better than 60 dB isolation
available
• FC, SC, or ST Style Outputs
• Low insertion loss
Wavelengths
1310 nm & 1550 nm ± 30 nm
Insertion Loss
≤ 1.5 dB @ 1310 nm
Minimum Attenuation
60 dB
Return Loss
50 dB (≥ 60 dB optional - angled FC)
Coarse Adjustment
0 to 60 dB nominal
Fine Adjustment
0 to 10 dB nominal
Connector
FC, ST, SC
General Specifications
Operating Temperature
-10 to +55°C
Storage Temperature
-30 to 60°C
Size (H x W x D)
5.5 x 2.75 x 1.5 in (14 x 7 x 3.8 cm)
Weight
6 oz. (168 grams)
© 2002, AFL Telecommunications, all rights reserved. VOA5-00-2000 Revision B, 9.15.05
Specifications are subject to change without notice.
51
VOA 5 Variable Fiber Optic Attenuator
The VOA 5-MM (multimode) and VOA 5-SM (single-mode) are hand-held, field-rugged
variable optical attenuators suited for a wide range of fiber link certification and production
test applications. The VOA 5 can be operated under local control (front panel keypad) or
from a PC via a serial link using the supplied PC software. The VOA 5 offers high
bi-directional return loss and will maintain the set attenuation level when the unit is
powered down.
The VOA 5 is powered by (2) AA alkaline batteries or an AC power adapter. A NiCad
rechargeable battery pack is an option.
Specifications
Optical Specifications
VOA5-MM
VOA5-SM
62.5 µm, multimode
9 µm, singlemode
Wavelength Range
850 - 1300 nm
1290 - 1620 nm
Calibrated Wavelengths
850, 1300 nm
1310, 1550 nm
0 to 30 dB
0 to 60 dB
1.5 dB @ 850 nm
3.0 dB @ 1300 nm
2 dB
Fiber Type
Attenuation Range
Features
• Multimode and single-mode models
• Hand-held (0.55 kg, 1.22 lb)
• High speed (0 to 60 dB < 3 s)
• Low insertion loss (< 2 dB, single-mode)
• Remote (SCPI) control via serial port
• LabVIEW® drivers provided
• AA Alkaline, NiCad, or AC powering
• Long battery life (> 16 hours)
Applications
• Portable VOA for fiber optic link installation and certification tests
• Programmable VOA for production and
QA environments
• Low-cost bench-top VOA for development labs
Insertion Loss (max.)
Return Loss (min.)
20 dB
40 dB
Display Resolution
0.1 dB
Accuracy @+25ºC
±0.20 dB typical, ±0.4 dB max (0 dB to 30 dB)
±0.3 dB typical, ±0.6 dB max (30 dB to 60 dB)
Repeatability @+25ºC
± 0.25 dB*
Maximum Input Level
+ 24 dBm
General Specifications
VOA5-MM
Battery Life (alkaline)
Speed
VOA5-SM
10 hrs
> 16 hrs
0-30dB in less than 5 seconds
0-60dB in less than 3 seconds
Power
2 AA alkaline, 120/220 AC adapter, or NiMH battery pack (optional)
Size (H x W X D)
18.5 x 11.1 x 4.6 cm (7.3 x 4.4 x 1.8 in.)
Weight
0.55 kg (1.22 lb)
Operating Temperature
0° to +50° C
Storage Temperature
-20° to +60° C
Relative Humidity
0 to 90% (non-condensing
Standard Connector Type
SC/UPC, FC/UPC, ST/UPC
* Repeatability is defined as the mean plus one standard deviation-typical value.
Ordering Information
Model
Includes
All VOA 5 models
Protective rubber boot, 2 AA alkaline batteries, 120/ 220 V AC power adapter, hex head
screwdriver, manual, and carry case.
* Specify optical connector and AC power cord type.
© 2002, AFL Telecommunications, all rights reserved. VOA5-00-2000 Revision B, 9.15.05
Specifications are subject to change without notice.
52
OFI Optical Fiber Identifiers
Noyes Optical Fiber Identifiers are rugged, handheld, and easy-to-use fiber optic test
instruments designed to detect optical signals transmitted through a single-mode fiber
without disrupting traffic. During installation, maintenance, rerouting, or restoration; it is
often necessary to isolate a specific fiber. By simply clamping an Optical Fiber Identifier
onto a gently bent fiber, the unit will indicate if there is [No Signal], [Tone], or [Traffic] and
identify signal direction.
OFI 200
The OFI 200 model and OFI 400 model Identifiers are equipped with a unique two-position
head design that can be configured to work with 250 µm, 900 µm, ribbon, or jacketed
fiber in seconds, without tools or adjustments. When testing coated fibers, the slim design
of the OFI 200 and OFI 400 models allows easier access on a splice tray where the
amount of work space is limited. The clamping trigger is ergonomically designed to fit the
natural motion of the operator’s hand. A high impact molded plastic case makes the OFI
models suitable for use outside plant or in the central office.
The OFI 400 model is the next generation of Noyes Optical Fiber Identifiers. It has all the
features of the OFI 200 model plus easy-to-read LCD display with Backlight, multiple
[TONE] signal detection (270 Hz, 330 Hz, 1 kHz, or 2 kHz), power saving feature, and [Set
Reference] feature. The OFI 400 model also measures and displays fiber core power or
relative power on an LCD display.
Both models are battery operated with the battery indication feature and perform thousands of tests before batteries replacement is necessary.
Features
OFI 400
• Rugged, handheld, lightweight
• Accepts 250 µm, 900 µm coated fiber, 3 mm jacketed fiber cable, and ribbon fiber
• No head swapping or adjustments
• Identifies light carrying fiber
• Low insertion loss - traffic remains uninterrupted
• Indicates direction of traffic
• Indicates Tone signal visually and audibly
• 2 kHz Tone detection - OFI 200 models
• 270 Hz, 330 Hz, 1 kHz, and 2 kHz Tone detection - OFI 400 models
• Easy-to-read LCD display with Backlight - OFI 400 models
• Measures fiber core or relative power - OFI 400 models
• Power Off and Set Reference feature - OFI 400 models
• Battery operated
• Low battery indication
• Low cost, easy to use
continued on the next page
© 2002, AFL Telecommunications, all rights reserved. OFI1-11-2000 Revision 1E, 6.10.05
Specifications are subject to change without notice.
53
OFI Optical Fiber Identifiers
Applications
• Live fiber identification - used during
installation, maintenance, rerouting, or
restoration to positively identify fibers
prior to cutting and splicing
• Tone detection
• The OFI 400 models may also be used
for measuring core power or relative
power
Ordering Information
Model
Includes
OFI 200D
User's guide and carry case
OFI 400
User's guide and carry case
Specifications
Detectable signal range
Fiber Type
Parameter
250 μm coated fiber
(SMF-28 with 250 μm CPC6 coating)
1310 nm, CW or Traffic
Minimum detect level
1310 nm, Tone
(average power,
1550 nm, CW or Traffic
typical)
1550 nm, Tone
Wavelength, Signal
Insertion loss
(typical)
3 mm jacketed fiber
(SMF-28 with 250 μm CPC6 coating
and 3 mm, yellow jacket)
Optical Specifications
Model
1310 nm
1550 nm
1310 nm, CW or Traffic
Minimum detect level
1310 nm, Tone
(average power,
1550 nm, CW or Traffic
typical)
1550 nm, Tone
Insertion loss
(typical)
1310 nm
1550 nm
OFI 200D
OFI 200D
OFI 400
-40 dBm
-43 dBm
-45 dBm
-50 dBm
-45 dBm
-45 dBm
-50 dBm
-50 dBm
0.6 dB
2.5 dB
0.6 dB
2.5 dB
-30 dBm
-32 dBm
-33 dBm
-37 dBm
-30 dBm
-30 dBm
-33 dBm
-33 dBm
0.8 dB
2.5 dB
1.0 dB
2.8 dB
OFI 400
Detector type
InGaAs
Wavelength range
800 - 1700 nm
Calibrated size of fiber and wavelength
N/A
Fiber stress
250 µm (SMF-28) @1550 nm
<100 kPSI max
Fiber size
250 µm, 900 µm, 2 mm or 3 mm jacketed & ribbon fiber
Tone detection
2000 ±100Hz
270, 330, 1000, or 2000 Hz (±5%)
Core power measurement range
N/A
+13 dBm to – 50 dBm
SMF28/28E 250um @ 1550nm
Measurement units
N/A
dBm, dB
N/A
Multi 7 segment LCD; 3 LEDs;
1 piezo buzzer
General Specifications
Display Type
Power
Battery life
Operation temperature
1 x 9V Alkaline
2 x 1.5V Alkaline
>10,000 operations typical
>10,000 operations typical
0° to 50°C 90% RH (Non-condensing)
Storage temperature
-30 to +60°C 90% RH (Non-condensing)
Dimensions (H x W x D)
8.5 x 1.5 x 1.1 in. (22 x 3.8 x 2.8 cm)
Weight
7.5 oz. (210 g)
6 oz (168 g)
Notes:
1 250 µm coated fiber parameters are specified with OFI plunger in the “250/900/RIB” position.
2mm/ 3mm jacketed fiber parameters are specified with OFI plunger in the “2 mm/ 3 mm” position.
2 Unless noted otherwise, all specifications are typical. Actual results can vary by several dB depending on fiber type, coating material, jacket color, jacket hardness, and other factors.
All specifications stated above are as measured at 25°C.
3 [CW] is a light signal that is not modulated.
[Traffic] is a light signal modulated by a random data sequence.
[Tone] is a light signal modulated into a nominal 50% duty cycle square wave.
© 2002, AFL Telecommunications, all rights reserved. OFI1-11-2000 Revision 1E, 6.10.05
Specifications are subject to change without notice.
54
OFI-FTTx Active ONT Detector
The OFI-FTTx is a rugged, hand-held optical fiber identifier designed to identify the
presence or absence of an active Optical Network Terminal (ONT) on FTTx F2 fibers at the
Fiber Distribution Hub (FDH). During a test the F2 fiber does not have to be removed from
service. Thus the OFI-FTTx can verify whether a splitter pigtail at the FDH is connected
to an active circuit before it is disconnected for fault location or re-use. The OFI-FTTx
can help verify FTTx network records and recover splitter pigtails and F2 fibers that are
connected at the FDH but, in fact, are available for new customers.
When applied to a splitter pigtail at the FDH, the OFI FTTx will report either that the ONT
is ‘Active’ or ‘Not Detected’. Time to complete each test is typically one second. The OFIFTTx is compatible with 2 mm jumper cable containing standard single-mode fiber, such
as SMF-28e ®, or bend insensitive fiber (BIF) with a 15 mm bend radius specification,
such as AFL BendLite ™.
Applications
• FACILITY RECOVERY: Harvest unparked
splitter legs and F2 fibers not connected
to subscribers.
• TROUBLE-SHOOTING: Real-time
confirmation of OLT to ONT connectivity
at the FDH.
Ordering Information
Model
Includes
OFI-FTTx
OFI-FTTx, user's guide, and carry case
The OFI-FTTx is powered by two standard AAA alkaline batteries, provides a low battery
indication, and can typically be operated 800 times before battery replacement is
necessary.
Features
• Rugged, handheld, lightweight
• In-service detection of upstream (1310 nm) activity on FTTx networks
• Determines which unparked splitter pigtails are connected to ONTs
• Does not require travel to customer (ONT) site
• Does not require disconnect of splitter pigtails
• Visual and audible indicators
• Battery operated
• Low battery indication
• Patent pending
Specifications
Model
Network Types
Network Locations
Fiber Type
Induced Loss (Typ)
Test Time (Typ)
Operating Range*
OFI-FTTx
FTTx BPON, GPON, EPON, ≥ 1:4 splitter ratio
Between splitter and customer ONT
2 mm jacketed SMF-28e ®; 15 mm bend radius AFL BendLite ™ (BIF); and equivalents
< 1 dB @ 1550 nm
1 sec
Loss from ONT to FDH: 0 to 7 dB (BPON), 0 to 9 dB (GPON, EPON)
User interface
Audio indicator and four red LEDs
Power
2 x AAA batteries
Battery Life
800 tests typical
Operating Temperature
-10 to 40°C
Storage Temperature
-20 to 50°C
Dimensions (H x W x D)
8.5 x 1.5 x 1.25 in (22 x 3.8 x 3.2 cm)
Weight
0.5 lbs (0.23 kg)
* Maximum values are typical and depend on fiber type and jacket material.
© 2006-2008, AFL Telecommunications, all rights reserved. M200-00-2000 Revision B, 08. 25.08
Specifications are subject to change without notice.
55
Download PDF
Similar pages