Quadro4Li Manual I: Installation Guide

Quadro4Li Manual I: Installation Guide
Copyright and Trademarks
Copyright © 2003-2011 Epygi Technologies, Ltd. All Rights Reserved. Quadro is a registered trademark of Epygi Technologies, Ltd. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other
trademarks and brand names are the property of their respective proprietors.
Limited Warranty
Epygi Technologies, Ltd. (‘Epygi’) warrants to the original end-user purchaser every Quadro to be free from physical defects in material and workmanship under normal use for a period of one (1) year from the date of purchase (proof of purchase required) or two (2) years from the date of purchase (proof of purchase required) for products purchased in the
European Union (EU). If Epygi receives notice of such defects, Epygi will, at its discretion, either repair or replace products that prove to be defective.
This warranty shall not apply to defects caused by (i) failure to follow Epygi’s installation, operation or maintenance instructions; (ii) external power sources such as a power line, telephone line, or connected equipment; (iii) products that
have been serviced or modified by a party other than Epygi or an authorized Epygi service center; (iv) products that have
had their original manufacturer’s serial numbers altered, defaced, or deleted; (v) damage due to lightning, fire, flood, or
other acts of God.
In no event shall Epygi’s liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation. Epygi offers no
refunds for its products. Epygi makes no warranty or representation, expressed, implied, or statutory, with respect to its
products or the contents or use of this documentation and all accompanying software, and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose.
Return Policy
If the product proves to be defective during this warranty period, call Epygi Customer Support at (972) 692-1166 to obtain
a Return Material Authorization (RMA) Number. Registered users also may access Epygi’s Technical Support
(www.epygi.com; ‘Support’) to send their RMA request. For Brazil representatives, call (21) 2518-3161 or contact via Web
(www.saga.com.br). Please have your proof of purchase on hand when contacting us. When returning a product, mark
the Return Authorization Number clearly on the outside of the package and include your original proof of purchase. Return
requests cannot be processed without proof of purchase. Customers are responsible for shipping and handling charges
when shipping to Epygi.
Epygi or its service center will use commercially reasonable efforts to ship a replacement product within ten (10) working
days after receipt of the returned product. Actual delivery times may vary depending on customer location.
Epygi reserves the right to revise or update its products, pricing, software, or documentation without obligation to notify
any individual or entity. Please direct all inquiries to:
Epygi Technologies, Ltd., Two Legacy Town Center, 6900 North Dallas Parkway, Suite 850, Plano, Texas 75024
Representative in Brazil - Saga Sistemas e Computadores SA, Av. Rio Branco, 18 - 8 andar, Rio de Janeiro 20090-001
Notice to Users
This Installation Guide, in whole or in part, may not be reproduced, translated, or reduced to any machine-readable form
without prior written approval.
Epygi provides no warranty with regard to this Installation Guide or other information contained herein and hereby expressly disclaims any implied warranties of merchantability or fitness for any particular purpose in regard to this manual or
other such information. In no event shall Epygi be liable for any incidental, consequential, or special damages, whether
based on tort, contract, or otherwise, arising out of or in connection with this manual or other information contained herein
or the use thereof.
FCC Statement (Part 15) Class A
• The Epygi Quadro4Li has been tested and found to comply with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the aforementioned measures.
You are cautioned that any change or modification to the equipment not expressly approved by the manufacturer could
void the user’s authority to operate this device.
Administrative Council for Terminal Attachments (ACTA) Customer Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back of this
equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ###TXXXX,
made out to HX7OT00BHX70100. If requested, this number must be provided to the telephone company.
Any plug or jack that is used to connect this equipment to the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by the ATCA.
The Ringer Equivalence Number is an indicator of the maximum number of devices allowed for connection to a telephone
interface. The termination on an interface may consist of any combination of devices subject only to the requirements that
the sum of the RENs of all the devices does not exceed five. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming line. The REN for this product is part of the product identifier that has the
format US:AAAEQ###TXXX, made out to HX7OT00BHX70100. The digits represented by ### are the REN without a decimal point (in this case 00B is a REN of 0.0B.)
If the Quadro causes harm to the telephone network, the telephone company will notify you in advance that a temporary
discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the opQuadro4Li; (SW Version 5.2.x)
Quadro4Li Manual I: Installation Guide
eration of the equipment. If this happens, the telephone company will provide advance notice for you to make the necessary modifications to maintain uninterrupted service.
Connection to a party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or the corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of the Quadro
does not disable your alarm equipment. If you have any questions about what will disable alarm equipment, consult your
telephone company or a qualified installer.
Electrical Safety Advisory
To reduce the risk of damaging power surges, we recommend you install an AC surge arrestor in the AC outlet from which
the Quadro is powered.
Industry Canada Statement
This product meets the applicable Industry Canada technical specifications.
Safety Information
Before using the Quadro, please review and ensure the following safety instructions are adhered to:
• To prevent fire or shock hazard, do not expose your Quadro to rain or moisture.
• To avoid electrical shock, do not open the Quadro. Refer servicing to qualified personnel only.
• Never install wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specified for wet locations.
• Never touch uninsulated telephone wire or terminals unless the telephone line has been disconnected at the network interface.
• Use caution when installing or modifying cable or telephone lines.
• Avoid using your Quadro during an electrical storm.
• Do not use your Quadro or telephone to report a gas leak in the vicinity of the leak.
• An electrical outlet should be as close as possible to the unit and easily accessible.
Emergency Services
The Quadro SIP Service is intended to function as a secondary telephone service. This service is made available through
the Internet and therefore is dependent upon a constant source of electricity and network availability. If a power outage
occurs, the Quadro SIP Service automatically will be disabled. User understands in the event of a power or network outage, the Quadro SIP Service will not support 911 emergency services, and further, such services only will be available via
the user's regular telephone line that is not connected to the Quadro. User further acknowledges that any interruption in
the supply or delivery of electricity or network availability is beyond Epygi's control and Epygi shall have no responsibility
for losses arising from such interruption.
Quadro4Li; (SW Version 5.2.x)
Quadro4Li Manual I: Installation Guide
Table of Contents
Manual I: Installation Guide
About This Installation Guide ........................................................ 6
Requirements............................................................................. 7
Hardware Overview..................................................................... 8
The Connectors Panel of Quadro4Li..........................................................8
Quadro4Li’s Front Panel LEDs..................................................................9
Step 1: Installing the Quadro ..................................................... 10
Networking Overview ........................................................................... 10
LAN/WAN Connection Options ............................................................... 11
Connecting the Hardware ..................................................................... 13
Step 2: Configuring the Quadro .................................................. 15
Step 2.1: Logging into Quadro .............................................................. 15
Step 2.2: System Configuration Wizard .................................................. 16
System Configuration .....................................................................................16
DHCP Settings for the LAN Interface .................................................................17
Regional Settings...........................................................................................17
Emergency and PSTN Access Code Settings .......................................................18
Finishing the System Configuration Wizard ........................................................19
Step 2.3: Internet Configuration Wizard ................................................. 21
Uplink Configuration .......................................................................................22
WAN IP Configuration .....................................................................................23
PPP/PPTP Configuration...................................................................................24
WAN Interface Configuration ...........................................................................25
DNS Settings ................................................................................................25
Finishing the Internet Configuration Wizard........................................................26
Step 2.4: Configuring the ISDN Settings ................................................ 27
Run the ISDN Wizard......................................................................................27
Step 2-A: Using IP Lines ............................................................ 32
Supported SIP Phones.......................................................................... 35
Tested SIP phones............................................................................... 36
Step 2-B: Using Key System Emulation ........................................ 36
Using SLA Lines for SIP Calls ................................................................ 37
Disabling the Key System Emulation ...................................................... 39
Step 2-C: Using Receptionist ...................................................... 39
Step 3: Registering on Epygi’s Technical Support........................... 40
Step 4: Making/Receiving Calls ................................................... 41
Using the Default SIP Addresses............................................................ 41
Appendix: Changing the Admin Password ..................................... 43
Appendix: Configuring NAT Traversal ........................................... 45
Appendix: Registering on Epygi’s SIP Server................................. 47
Quadro4Li; (SW Version 5.2.x)
Quadro4Li Manual I: Installation Guide
Appendix: Checking the Connections ........................................... 51
Appendix: Pin Assignment of ISDN .............................................. 53
Manual II: see Administrator's Guide
This guide describes in detail the menus available for administrators only. Furthermore, it includes all the system’s default values at a glance.
Manual III: see Extension User's Guide
This guide describes in detail the menus available for extension users. Furthermore, it includes all the call codes at a glance.
Quadro4Li; (SW Version 5.2.x)
Quadro4Li Manual I: Installation Guide
About This Installation Guide
About This Installation Guide
This Installation Guide explains the installation of the Quadro IP PBXs of Quadro4Li series.
Quadro4Li offers 4 phone lines (ISDN), 1 Ethernet LAN port and 1 Ethernet WAN port as
external interfaces.
This Installation Guide gives step-by-step instructions to provision the Quadro and configure the phone extensions with the Epygi SIP Server. After successfully configuring the
Quadro, a user will be able to make SIP phone calls to remote Quadro devices, make local
calls to the PSTN and access the Internet from devices connected to the LAN.
This Installation Guide neither describes the PBX, Auto Attendant, Call Relay, and Voice
Mail features of the Quadro nor does it provide advanced firewall and VPN configuration information. For these features, refer to the Administrator's and Extension User's Guides.
Step 1: Installing the Quadro explains the connection of cables and devices to the Quadro.
Step 2: Configuring the Quadro describes the configuration steps necessary to integrate
the Quadro into your network environment.
Step 2-A: Using IP Lines explains how to configure IP lines on the Quadro IP PBX.
Step 2-B: Using Receptionist refers to the document describing Receptionist’s configuration on the Quadro.
Step 3: Registering on Epygi’s Technical Support shows you how to access the Epygi
Technical Support Center and the Epygi SIP Server.
Step 4: Making/Receiving Calls explains how to enable the Quadro’s various telephony
features.
Appendix: Changing the Admin Password explains how to change the default administrator password.
Appendix: Configuring NAT Traversal explains configuration of the Quadro if it is placed
behind a NAT enabled router.
Appendix: Registering on Epygi’s SIP Server explains how to register on Epygi's powerful
SIP server.
Appendix: Checking the Connections gives hints on solving common problems.
Quadro4Li; (SW Version 5.2.x)
6
Quadro4Li Manual I: Installation Guide
Requirements
Requirements
• One 120/240 V power outlet in close proximity to the Quadro4Li.
• One RJ-45 Ethernet 10/100 broadband Internet connection, if Quadro4Li shall be
used as a standalone gateway
• One CAT 5 Ethernet cable with an RJ-45 connector to connect to the Quadro4Li
LAN port
• One PC with a 10Mbps or a 10/100 Mbit/s Ethernet card or adapter installed.
• TCP/IP network protocol installed on each PC.
• For optimal results, Internet Explorer 5.5 or higher, or Netscape Navigator 4.7 or
higher are recommended.)
Please Note: The Quadro4Li is shipped with one straight RJ-45 CAT 5 cable. If the LAN
connector of the Quadro4Li is to be connected to a hub or switch, a crossover cable may
be required (see Appendix: Pin Assignment of ISDN, too).
Quadro4Li; (SW Version 5.2.x)
7
Quadro4Li Manual I: Installation Guide
Hardware Overview
Hardware Overview
The Connectors Panel of Quadro4Li
The illustration below includes the connectors panel of Quadro4Li model.
Fig. l- 1: Connectors Panels of Quadro4Li IP PBX
1
2
3
4
5
6
Power supply socket. Use only the power adapter delivered with the Quadro.
ISDN sockets to connect the Quadro to the ISDN network termination units to use
PSTN services. A straight Ethernet CAT 5 cable can be used with an RJ45 connector
according to the ISDN Pin assignment, see Appendix: Pin Assignment of ISDN.
The Reset button may be used in two ways: (1) to initiate a normal reset or (2) to carry out a factory reset. A normal reset is executed by pressing the Reset button with a
paper clip for an instant.
Pressing the reset button and holding it down for seven seconds or more will execute
a factory reset. This will restore the factory defaults and clear all settings including
the IP address and the administration password you entered.
Please Note: A Factory Reset forces the default LAN IP address of 172.30.0.1 and
default admin password of 19.
RJ45 socket to attach to the Local Area Network (LAN) via an Ethernet CAT 5 cable.
If a PC is connected directly to this socket, a straight cable is used. If an Ethernet
hub, router or switch is used; a crossover cable may be required.
This port may also be used to connect IP phones to the Quadro (optional). In this
case, it is recommended to use a hub or a switch to connect the PC along with IP
phones to the Quadro’s LAN port.
RJ45 socket to attach the Internet Uplink (WAN) via an Ethernet CAT 5 cable. This
port may also be used to connect IP phones to the Quadro. The default configuration
settings assume that IP phones are attached to this, rather than the LAN port.
The NT/TE switches are used to control the Quadro4Li device on the S/T Bus. If the
Quadro4Li is connected to the beginning or end of the S/T Bus or if there is only one
ISDN unit connected to the S/T Bus, then this switch should be toggled to the NT
(Network Terminator) position. Otherwise, if the Quadro4Li is connected in the middle
of the S/T Bus, the switch should be toggled to the TE (Terminal Endpoint) position.
S/T Bus is a full-duplex interface. It consists of two groups (one for transmit and the
other one for receive) of two-wire interface and might support multiple devices (up to
8 devices can be attached to the S/T Bus). Both ends of each of the two-wire interfaces should be terminated (100ohm resistance is present at both ends of each twowire interface).
Please Note: If the trunks on the Quadro4Li have incorrect NT/TE position, they may
not function properly, including connection establishment permanent failure.
Quadro4Li; (SW Version 5.2.x)
8
Quadro4Li Manual I: Installation Guide
Step 1: Installing the Quadro
Quadro4Li’s Front Panel LEDs
Fig. I-1: Quadro4Li's Front Panel LEDs
1
Busy
green
Status of CPU
off: no power
on or blinking: normal activity
on: device is booting
off: no information
blinking: an event occurred; details specified in the System Event section of the Management interface
2
Info
yellow
System information
3
Fault
red
System status
on either an error or the device is booting
off: no error
blinking: system unusable
PWR
green
Status of the power supply
on: power supply ok
off: no power supply or device is still booting
5
Line 1
green
Status of the ISDN1 line
on: all channels on the Line 1 are busy
off: no call in progress or one active call
flickering: ISDN Line 1 is disconnected
6
Line 2
green
Status of the ISDN2 line
on: all channels on the Line 2 are busy
off: no call in progress or one active call
flickering: ISDN Line 2 is disconnected
7
Line 3
green
Status of the ISDN3 line
on: all channels on the Line 3 are busy
off: no call in progress or one active call
flickering: ISDN Line 3 is disconnected
8
Line 4
green
Status of the ISDN4 line
on: all channels on the Line 4 are busy
off: no call in progress or one active call
flickering: ISDN Line 4 is disconnected
4
LED Indication during a firmware update
A firmware update is indicated by the red (Fault) and yellow (Info) LEDs. Both will blink simultaneously for about two minutes while the firmware is being updated. The Quadro4Li
will then reboot automatically showing the boot LED sequence.
LED indication during a boot sequence
A boot sequence is indicated as follows: The red Fault LED will glow for a few seconds,
then the yellow Info LED will glow for another four or five minutes while the green Busy
LED is blinking. Once the Info LED is off, the boot sequence has been completed successfully.
LED indication during emergency firmware upload
The red Fault LED and the yellow Busy LEDs will stop blinking alternately and start blinking in parallel. This shows that Quadro has accepted the emergency firmware and is loading it. After a few seconds, Quadro will boot, indicated as follows: The red Fault LED will
glow for a few seconds, then the yellow Info LED will glow for another few seconds while
the green Busy LED is jittering. When the yellow Info LED extinguishes, the boot sequence has been completed successfully.
Quadro4Li; (SW Version 5.2.x)
9
Quadro4Li Manual I: Installation Guide
Step 1: Installing the Quadro
Step 1: Installing the Quadro
Networking Overview
To establish a connection between the Internet and your local area network (LAN), an access router is needed. The Quadro4Li may serve, among other functions, as an access
router, and will perform the task of connecting your LAN, or a group of one or more PCs, to
the wide area network (WAN) or the Internet. The Quadro will process and regulate the data traffic between these two networks. The Quadro4Li has one LAN port that can connect to
Ethernet hubs and switches on the LAN, allowing additional devices to be connected to the
network.
The Quadro is a device with two sides: one side connects to your LAN, and the other side
connects to the Internet, or the WAN. Quadro’s firewall and Network Address Translation
(NAT) functionality protects your LAN from being seen from the Internet side making the
LAN private and secure.
The Ethernet WAN port transmits up to 10 Mbps, and the LAN port transmits at 10 Mbps or
100 Mbps.
Every device within an IP network requires a unique IP address to identify itself. Since the
Quadro connects to both the LAN and the WAN, it has to be part of both networks, and
must have two IP addresses: one for the WAN side and one for the LAN side. The Quadro’s integrated firewall/NAT functionality will hide the LAN IP address from the WAN (Internet) side.
There are two ways of assigning a WAN IP address: statically or dynamically.
A Static IP address is a fixed, manually assigned IP address that remains valid until
changed. If you plan to use the Quadro as your Internet access router, contact your Internet
Service Provider (ISP) to find out if a static IP address is assigned to your account. If so,
you will need this static IP address when configuring the Quadro device.
A dynamic IP address is a temporary address that is automatically assigned by your ISP
and will change periodically. If your ISP offers a dynamic IP address, the Quadro will act as
a DHCP client and will receive a new IP address from the ISP’s DHCP server or PPPoE
feature.
Please Note: A DHCP client is a piece of software that requests an IP address from a
DHCP server. A DHCP server assigns on request a unique IP address to a device. The
Quadro, like many routers, acts as a DHCP client on its WAN interface and as a DHCP
server on its LAN interface.
The Quadro must be visible to the Internet to be able to receive and send VoIP calls. When
the Quadro is placed in a private network, typically behind existing routers, it will by default
attempt to pass through the NAT of this router with its STUN (Simple Traversal of UDP over
NAT) feature. STUN will work without user configuration with the majority of basic routers.
In some scenarios, port forwarding on the router is required to make the Quadro accessible
to other Quadro devices and the Epygi SIP Server on the Internet. Another configuration
option is to use the Quadro as the Internet access router, connected directly to the WAN,
eliminating the traverse to the local NAT firewall.
Quadro4Li; (SW Version 5.2.x)
10
Quadro4Li Manual I: Installation Guide
Step 1: Installing the Quadro
LAN/WAN Connection Options
•
A Quadro4Li with an Ethernet WAN port behind a router, which is connected to a cable or xDSL modem. IP phones are placed on the WAN side of
the Quadro4Li.
Fig. l-2: Configuration: Quadro4Li behind a router with IP phones on WAN
In this and the following configuration (Fig. l-2 and Fig. l-3), the IP router typically acts as a
DHCP server for the LAN and assigns the IP addresses to the PCs and other devices. The
Quadro can be connected through its WAN port directly to one of the router's LAN ports
and will get an IP address from the router. By default, the Quadro acts as a DHCP client on
the WAN port. The IP phones are placed on the WAN side of the Quadro4Li, connected to
the company LAN.
The Admin PC can be connected to the Quadro WAN (Fig. l-2) or LAN (Fig. l-3) port to access the Web Management of the Quadro.
Please Note: Since Quadro uses STUN by default, it will work with most basic routers without any further configuration.
•
A Quadro4Li with an Ethernet WAN port behind a router, which is connected to a cable or xDSL modem. IP phones are placed on the LAN side of
the Quadro4Li.
Fig. l-3: Configuration: Quadro4Li behind a router with IP phones on LAN
Quadro4Li; (SW Version 5.2.x)
11
Quadro4Li Manual I: Installation Guide
•
Step 1: Installing the Quadro
A Quadro4Li used as an Internet Access Router, connected directly to the
Internet.
Fig. l-4: Configuration: Quadro used as Internet Access Router
Please Note: The Admin PC is connected to the Quadro’s LAN port through a switch/hub
to access the Web Management of the Quadro (see Fig. l-3 and Fig. l-4). It is recommended to have Admin PC acting as a DHCP client and obtaining IP address from the
Quadro.
Quadro4Li; (SW Version 5.2.x)
12
Quadro4Li Manual I: Installation Guide
Step 1: Installing the Quadro
Connecting the Hardware
•
Quadro4Li behind a router with IP phones connected to WAN
Fig. l- 5: Installation: Quadro4Li behind a router with IP phones on WAN
•
Quadro4Li behind a router with IP phones connected to LAN
Fig. l- 6: Installation: Quadro4Li behind a router with IP phones on LAN
•
Quadro4Li used as Internet access router
Fig. l- 7: Installation: Quadro4Li used as an Internet Access Router
Quadro4Li; (SW Version 5.2.x)
13
Quadro4Li Manual I: Installation Guide
•
•
•
•
•
•
•
•
•
•
Step 1: Installing the Quadro
Verify the product package contents are complete. Refer to the contents sheet included in the packaging to determine if all the items were shipped in the box.
Before you connect the hardware, make sure that all devices are powered off.
Connect the Quadro4Lis LINE ports to the trunk from the NT1 (Network Termination
Unit) attached to the PSTN Central Office via straight CAT 5 cable (see Appendix: Pin
Assignment of ISDN).
Connect the Ethernet port on your PC via a straight CAT 5 cable with an RJ45 connector to the LAN or WAN socket of the Quadro. If a hub or switch is connected between the Quadro and your PC, use a crossover cable from the LAN interface of the
Quadro to the hub/switch.
Connect at least one SIP phone to the Quadro. You will need an intermediate
hub/switch. Use a crossover cable to connect the hub/switch to the Quadro’s LAN or
WAN socket. Plug your SIP phones to the hub/switch with a straight CAT 5 cable with
an RJ45 connector. The same hub/switch can also be used to connect PCs to the Quadro.
Connect the WAN port of the Quadro to the Internet service via a cable or DSL modem.
Power up the DSL or Cable modem first.
Connect the power adapter to the POWER port on the Quadro’s rear panel and plug
the power adapter into a power outlet. Only use the original Quadro power adapter
and plug it into a power strip with surge protection or to a UPS if available.
The red LED (Fault) will glow for several seconds followed by the yellow LED (Info),
which will glow for several minutes. When Info LED is off, the Quadro is operational.
Power up any hub or switch followed by any PC and other devices on the LAN side.
Check the LEDs: The green Busy LED must glow continuously. The green LAN and
WAN LEDs will blink when cables are connected to these ports and all devices are
powered up. If the green LAN and WAN LEDs do not blink, verify cabling and ensure
that all devices are powered up.
Please Note: CAT 5 cables can be faulty without any visual indication. The LAN and
WAN LEDs verify that the Ethernet connection is established between the end points.
If these LEDs are not illuminated, there is a connection problem between the Quadro
and the other device. Some modems, hubs, switches and routers will require the use
of crossover cables.
Quadro4Li; (SW Version 5.2.x)
14
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Step 2: Configuring the Quadro
Step 2.1: Logging into Quadro
•
•
•
Start a browser (MS Internet Explorer, Netscape, Opera) on a PC connected
to the Quadro4Li via the LAN or WAN interface.
In the address field, enter http://Quadro_WAN_IP (the IP address assigned
by the company’s DHCP sever) if the PC is connected to the Quadro WAN
port; or http://172.30.0.1 (Quadro’s default LAN IP address) if the PC is connected to the Quadro’s LAN port
The Login page of the Quadro will be displayed (see Fig. l- 8).
Fig. l- 8: Login page
Enter admin as the Username and 19 as the password to log in as the administrator. Once
you log in, you will enter into the Quadro Management Menu.
Please Note: If you consecutively enter a wrong password and/or username for five times
the device will be unavailable for login for five minutes.
After logging in, the Quadro Management page will be displayed.
Fig. l- 9: Quadro Management page
Quadro4Li; (SW Version 5.2.x)
15
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Step 2.2: System Configuration Wizard
The System Configuration Wizard must be run upon Quadro first startup. The System
Configuration Wizard is a tool for the administrator to specify regional configuration settings and to define the Quadro's Local Area Network settings.
To run the wizard, select the System Configuration Wizard from the System menu.
For the basic configuration, some pages in this wizard may be skipped and left default for
the basic configuration.
Please Note: It is strongly recommended that factory default settings are left unchanged if
their meanings are not completely understandable to the party administrating the Quadro.
System Configuration
The first page of System Configuration Wizard shows all items to be configured. Click the
Next button to start. Enter into the Host Name field the unique name (top right corner, under Epygi logo) for the Quadro device. The Domain Name text field requires the LAN side
domain name which the Quadro belongs to.
For a basic configuration, the LAN IP address does not need to be changed, but if you
must change it (for example, to integrate the device into an existing LAN), record the new
LAN IP address and have it handy. You’ll need it for subsequent access to Quadro’s management from its LAN interface.
Please Note: The Host Name is very useful when many Quadro's are part of a network
and one administrator has remote access to all of them. All Quadro pages show the hostname on the top right corner under Epygi logo.
Fig. l- 10: System Configuration page
Clicking Next shows the page DHCP Settings for the LAN Interface.
Quadro4Li; (SW Version 5.2.x)
16
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
DHCP Settings for the LAN Interface
If the DHCP server is enabled, the Quadro will automatically assign dynamic IP addresses
to the stations connected to its LAN port.
If you didn’t change the default LAN IP address of the Quadro, you also may leave the default values for the IP Address Range. Make sure your connected LAN devices belong to
the same network as the LAN port of your Quadro.
Please Note: Make sure there is only one DHCP server on the LAN, otherwise, unpredictable network behavior can occur.
Fig. l- 11: DHCP Settings for the LAN Interface page
Click on Next to display the Regional Settings page.
Regional Settings
If your Quadro is located outside of the United States, it is important to properly configure
your line connections to the PSTN in your location.
Fig. l- 12: Regional Settings page
Proper configuration of Regional Settings is important for the functionality of the voice
subsystem. The Regional Settings determine the proper telephony parameters on the LINE
ports of the Quadro for the specified country. Select the country where the Quadro is loQuadro4Li; (SW Version 5.2.x)
17
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
cated. If you do not find your country in the list, pick the closest in your timezone.
The Quadro obtains the correct time automatically over the Internet from a time server. If
you are not located in the US/Central standard time zone, you will need to change the
Timezone to your region.
Click on Next to display the Emergency and PSTN Access Code Settings page.
Emergency and PSTN Access Code Settings
Fig. l- 13: Emergency and PSTN Access Code Settings page
You may enter your local specific emergency codes into the appropriate field. For example,
in the United States the emergency number is 911, whereas in Germany it is 112,110. In
case of an emergency you can then pick up any IP phone and dial your configured emergency code without any prefixes for PSTN calls. To make an emergency call if at least one
ISDN timeslot is not attached to an SLA, press an appropriate extension button on your IP
phone (Line1-Line3 on Aastra phones, Programmable Buttons 1 -6 on Snom phones by default) and dial the emergency code. If timeslots of all ISDN trunks are attached to SLAs,
press an SLA button and then dial your configured emergency code (see Step 4: Making/Receiving Calls).
Please note: If all ISDN trunks are attached to SLAs, the emergency code specified on this
page will not work if the Blind Transfer to Extension service for SLAs is activated with
an empty access code and three-digit extensions are used on the system. For more information on the Blind Transfer to Extension Service, please see Manual II: Administrator’s
Guide.
The PSTN Access Code is the prefix number you choose to dial to tell the Quadro to “make
this call over PSTN” (see Step 4: Making/Receiving Calls). Users in the United States will
usually choose 9 here. European users usually would want to enter zero (0). If you do not
enter anything into this field the currently configured PSTN Access Code will stay unchanged.
Please note: By default all ISDN timeslots are assigned to SLA lines to allow direct access
to PSTN network (see Step 2-B: Using Key System Emulation). Therefore, in the default
configuration dialing the Access Code to access the PSTN network is not required.
Click on Next to display the Summary Page.
Quadro4Li; (SW Version 5.2.x)
18
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Finishing the System Configuration Wizard
Fig. l- 14: System Configuration Wizard finishing page
Click on Finish to complete the System Configuration Wizard. The Quadro will then stop internal functions and apply the changes made in the Wizard.
Fig. l- 15: Wizard Execution Progress page
After this is complete, the Quadro will reply with the Confirm Settings page requesting
confirmation of the changes. Press on OK to confirm the settings.
Quadro4Li; (SW Version 5.2.x)
19
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Fig. l- 16: Confirm Settings page
Please Note: You must confirm the settings within 20 minutes. Otherwise the device will
revert back to the previous configuration and reboot.
Please Note: If you do not use DHCP for your LAN and you have changed your LAN settings, make sure that the IP address of the PC connected to Quadro is still within the specified IP address range, otherwise your PC may not establish a connection to Quadro.
If you changed the network configuration of the LAN, restart your LAN connection to receive a new IP address from the new network. Then you can access the Web Management
of the Quadro on the new IP address you’ve assigned to the Quadro.
Quadro4Li; (SW Version 5.2.x)
20
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Step 2.3: Internet Configuration Wizard
Open the Internet Configuration Wizard by selecting the corresponding menu item on the
System menu. The Internet Configuration Wizard is a tool for the administrator to configure the WAN settings and to adjust Quadro's connectivity in the global network. It must be
run if Quadro is desired to be connected to the Internet.
The page Getting Started will be displayed:
Fig. l- 17: Internet Configuration Wizard
This first page of the Internet Configuration Wizard is for informational purposes only and
lists the items to be configured, Click on the Next button for the Uplink Configuration page.
Before configuring the WAN port to the Internet, you need to get the following information
from your internet service provider:
•
•
•
Bandwidth - how much is available upstream and downstream?
WAN IP Configuration - is DHCP supported? If yes, no more information is
needed. If DHCP is not supported, the following data is needed: the WAN IP address, the subnet mask, the IP address of the standard gateway and the IP address of the Domain Name Server (DNS).
MAC address - needed when the ISP requires a specific MAC address for the
WAN.
Additionally, for Point-to-Point Protocol over Ethernet (PPPoE) WAN interface, you need to
get the following information from your internet service provider:
•
PPP Configuration - does your ISP use a dynamic or fixed WAN IP address? If
the WAN IP address is dynamic, no more information is needed. If the WAN IP
address is fixed, you will have to enter it.
•
Authentication - does your ISP require authentication? If authentication is required, information about the corresponding method (PAP, CHAP or MSCHAP) is
needed including the username and password of the PPPoE account.
This information will be needed to be inserted in the Internet Configuration Wizard.
Quadro4Li; (SW Version 5.2.x)
21
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Uplink Configuration
Select the desired WAN Interface Protocol and enter the WAN Interface Bandwidth to assure the quality of IP calls.
Fig. l- 18: Uplink Configuration
If the available bandwidth is used to the point where the quality of an additional IP call
would suffer, then new IP calls are rejected.
The bandwidth provided by your ISP must be specified for both Upstream and Downstream fields. The default entry in both fields is 10000, the maximum bandwidth of the 10
Mbit/s uplink module. For basic DSL and cable modem service in the United States, typical
values are 300 for Upstream and 1500 for Downstream.
The Min Data Rate text field is used to specify the amount of bandwidth reserved for data
applications. The value entered here needs to be smaller that the value specified for Upstream Bandwidth.
Specify the WAN Interface Protocol by choosing between available WAN interface protocols: PPPoE (Point to Point over Ethernet), PPTP (Point to Point Tunneling Protocol) and
Ethernet. Use Ethernet for DHCP or static IP.
For Ethernet, clicking Next will display the WAN IP Configuration page. If PPPoE is the
selected WAN Interface Protocol, the next page will be PPP/PPTP Configuration. For PPTP
WAN Interface Protocol, PPP/PPTP Configuration page will follow the WAN IP Configuration.
Quadro4Li; (SW Version 5.2.x)
22
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
WAN IP Configuration
Your Internet Service Provider (ISP) should provide this information.
•
•
Assign automatically via DHCP - The parameters are set automatically by the
ISP. This is common with cable modem and DSL service.
Assign Manually requires the administrator to enter the external IP Address, the
corresponding Subnet Mask, and the IP address of the Standard Gateway. This
is common when you have a static IP address with your ISP.
Fig. l- 19: WAN IP Configuration page
Click on Next to display the WAN Interface Configuration page.
Quadro4Li; (SW Version 5.2.x)
23
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
PPP/PPTP Configuration
Enter the IP address of the PPTP server into the PPTP Server text field.
Choose the encryption for the traffic over the PPTP interface from the Encryption drop
down list.
Authentication Settings require the Username and the Password used for the authentication on the ISP server.
Dial Behavior radio buttons:
•
Dial Manually - if this radio button is activated, a button will be displayed in the
main management window that serves to switch the Internet connection on/off.
When accessing the Internet, every station of the connected LAN has to connect
to Quadro first.
•
Always connected - Quadro stays in the always connected mode. This will allow
Quadro always remain online in the network.
The IP Address Assignment field is used to specify the external IP address given to the
Quadro. Usually it is a dynamic address but in some cases you may be given a static IP
address.
Fig. l- 20: PPP/PPTP Configuration page
If your ISP assigns a dynamic IP address, activate the Dynamic IP Address radio button,
otherwise activate the Fixed IP Address radio button and enter the IP address you were
assigned by your ISP.
Keep Connection Alive checkbox enables keeping the connection alive by sending control
packets dedicated for the link state verification.
Click the Next button to display the WAN Interface Configuration page.
Quadro4Li; (SW Version 5.2.x)
24
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
WAN Interface Configuration
If your ISP requires a specific MAC address, (for example, for authentication), it can be entered on this page. The required MAC address can be entered into the User defined field.
If a specific MAC address is not required, leave the default selection This device selected.
Fig. l- 21: WAN Interface Configuration page
Use the MTU drop down list to select the maximum packet size on the Ethernet (in bytes).
Click Next to display the DNS Settings page.
DNS Settings
For DNS, the selection is set to Dynamically by Provider. When using a static IP address,
fixed values must be entered.
Fig. l- 22: DNS Settings page
The Quadro will suggest the correct settings. If Dynamically by Provider is selected, the
DNS server settings will be set automatically whenever a connection to the Internet is established.
If Fixed Nameserver Address is selected, manually enter the IP addresses provided by
your ISP for the name server and the alternative name server.
Clicking Next shows the summary page of the Internet Configuration Wizard.
Quadro4Li; (SW Version 5.2.x)
25
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Finishing the Internet Configuration Wizard
Fig. l- 23: Internet Configuration Wizard Summary page
Click the Finish button to complete the Internet Configuration Wizard. The Quadro will then
stop internal functions and apply the changes made in the Wizard. After this is complete,
the Quadro will display the Confirm Settings page requesting confirmation of the changes.
Press the OK button to confirm the settings.
Please Note: the settings should be confirmed within 20 minutes; otherwise, the device will
revert back to the previous configuration and reboot.
Quadro4Li; (SW Version 5.2.x)
26
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Step 2.4: Configuring the ISDN Settings
The Quadro4Li can be connected to a PBX or to the PSTN via ISDN trunks. The Quadro4Li
may be connected to act as a User (if connected to PSTN) or as a Network (if connected to
Legacy PBX).
Further, you are required to enter the ISDN settings your PSTN provider requires regarding
framing, clocking, signaling used and so on. All these settings must be configured during the
ISDN Wizard that starts when you press on the trunk in the ISDN Trunk Settings page accessible from the Telephony menu.
Fig. I-2: ISDN Settings page
The table on this page lists the available ISDN trunks of Quadro and their settings (trunk
name, interface and connection type). The ISDN Stats link is displayed for every active
ISDN trunk and leads to the page where the ISDN trunk and the traffic statistics can be
viewed.
Run the ISDN Wizard
Before starting the ISDN Trunk configuration, please consult with your ISDN provider administrator to receive instructions for which settings are necessary to be configured.
Run the ISDN Wizard for each ISDN trunk to make sure that all settings are proper. To access ISDN Wizard, push the appropriate trunk number in the ISDN Trunk Settings table.
The ISDN Wizard – ISDN Settings allows you to choose the interface type and the connection type of the selected trunk(s).
The Interface Type drop down list allows you to select between the User and the Network
interfaces. If a legacy PBX is connected, the interface configuration here should be Network. If an ISDN trunk from the CO (Central Office) is connected to the Quadro, the interface configuration here should be User.
The Connection Type manipulation radio button group allows you to choose the connection
type for the selected trunk(s):
• PTP (Point to Point) – choose this option when only one ISDN device is attached to
the Quadro. With this selection the TEI value should be defined manually later in the
ISDN Wizard.
• PTMP (Point to Multi Point) – choose this option when one or more ISDN devices are
attached to the Quadro. With this selection the TEI value will be defined automatically.
This selection also allows you to use the MSN services.
Please Note: Consult with your CO operator or network administrator before configuring the
ISDN connection type.
Quadro4Li; (SW Version 5.2.x)
27
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Fig. II-3: ISDN Wizard – ISDN Settings
The ISDN Wizard - Page 2 content is dependent on the connection type selected on the
previous page of ISDN Wizard:
For PTMP (Point to Multi Point) connection type selection, the next page in the ISDN Wizard is ISDN PTMP Settings.
The ISDN PTMP Settings page is used to turn on the MSN configuration. It is recommended to enable the MSN when there are multiple ISDN devices connected to the same
ISDN bus. If the MSN is enabled on this page, the next page will require the MSN table configuration.
Fig. II-4: ISDN Wizard – ISDN PRMP Settings
For PTMP (Point to Multi Point) connection type with MSN service selected, the Routing
Settings page is used to allocate MSN numbers to the certain destinations on the Quadro.
MSN numbers allow you to manage the ISDN numbers and to route them accordingly. The
MSN number can be assigned to Quadro extensions, to the Auto Attendant, or to the routing
client with two kinds of call routing possibilities, where incoming calls will be routed.
Quadro4Li; (SW Version 5.2.x)
28
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
The drop-down lists in the MSN Number column require the MSN numbers defined on the
Quadro.
Please Note: At least one MSN number should be defined in this list. The system displays
an error message if the same MSN number is used twice in the drop down lists on this page.
The Route Incoming Call to drop-down lists allow you to select the destination where the
incoming call addressed to the certain MSN number will be routed. Choosing the Routing
with inbound destination number selection will automatically use the initially dialed number to connect the destination without any additional dialing. For PTP (Point to Point) connection type or for PTMP (Point to Multi Point) connection type with MSN disabled, this
page contains only one Route Incoming Call to drop-down list.
Selecting Use Default outgoing Caller ID allows you to overwrite the source caller information with the one specified in the Default outgoing Caller ID text field when placing outgoing calls toward the CO. The Default outgoing Caller ID text field requires the Quadro identification number that should be registered and recognized at the CO for outgoing calls. If
this checkbox is enabled but no value is defined in Default outgoing Caller ID, empty caller
information will be sent to the CO. If this checkbox is disabled, the source caller information
will be forwarded to the CO.
Select the Advanced Settings checkbox if you wish to adjust trunk L2 and L3 Settings manually, otherwise leave this checkbox unselected to use the system default values.
Fig. II-5: ISDN Wizard – Routing Settings
The ISDN Wizard – L2&L3 Settings is used for advanced configuration only and contains
L2&L3 Settings. This page only appears when the Advanced Settings checkbox is selected
on the previous page of the wizard. This page contains the following components:
Quadro4Li; (SW Version 5.2.x)
29
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Fig. II-6: ISDN Wizard – l2&L3 Settings
ISDN L2 Timers:
• Excessive Ack. Delay T200 configures the period in milliseconds (numeric values from
500 to 9999) between the transmitted signaling packet and its acknowledgement received.
• Idle Timer T203 configures the period in milliseconds (numeric values from 1000 to
99999) for the ISDN client idle timeout.
ISDN L3 Timers:
• The T302 Timer text field requires the value for the T302 timer in milliseconds (digit
values from 0 to 15000). It indicates that the time frame system is waiting for a digit to
be dialed. When the timer expires, it initiates the call.
• T309 Timer requires the value for the T309 timer in milliseconds (numeric values from
0 to 90000). It is responsible for call steadiness during link disconnection within the period equal to this timer value. If the value in this field is zero (0), the T309 timer will be
disabled.
• T310 Timer requires the value for the T310 timer in milliseconds (numeric values from
1000 to 120000). It is responsible for the outgoing call steadiness when CALL PROCEEDING is already received from the destination but call confirmation (ALERT, CONNECT, DISC or PROGRESS) has not yet arrived.
• Alert Guard Timeout requires the value for the Alert Guard Timer in milliseconds (numeric values from 0 to 500) between CALL PROC and ALERT messages.
Alert Guard Timer it is used when Quadro is connected to a slow legacy ISDN-PBX.
Recommended values are:
- fast connection (0ms);
- normal (150ms), default;
- slow ISDN-PBX (350ms);
- very slow ISDN-PBX (500ms).
Quadro4Li; (SW Version 5.2.x)
30
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
The Coding Type drop down list allows you to select between a-law and mu-law coding
types.
The Switch Type is another configuration parameter that depends on the Service Provider.
The Passive Mode checkbox is used to leave the ISDN Layer1 connection in the Slave
mode. When this checkbox is selected, Layer1 remains idle when calls are not available.
When this checkbox is not selected, Quadro keeps its Layer1 always active. This checkbox
enables the Enable TEI Remove Procedure checkbox. With the Enable TEI Remove Procedure checkbox is selected, the trunk will lose the assigned TEI when entering into passive
mode on the Layer 2. The Passive Mode and Enable TEI Remove Procedure checkboxes
are present only for connection types different from PTP (Point to Point) selected on the
first page of ISDN Wizard. In case if PTP (Point to Point) connection type is selected on
the first page of the ISDN Wizard, these two checkboxes are replaced with a TEI Address
text field that requires the channel number (digit values from 0 to 63) for connection establishment between the CO and the ISDN client.
Channel Selection is used to select between the Preferred and Exclusive B channel selection methods. For Preferred channel selection, the CO answers to the call request by the
first available timeslot. With the Exclusive channel selection, the CO should feedback only
by the timeslot asked in the call request.
The Bearer Establishment Procedure drop down list allows selecting the session initiation
method on the B channel. One of the following options can be selected for the transmission
path completion prior to receipt of a call acceptance indication:
• on channel negotiation at the destination interface
• on progress indication with in-band information
• on call acceptance
The Calling Party Type of Number drop down list allows you to select the type identifying
the origin of call.
The Called Party Type of Number drop down list allows you to select the type identifying
the subaddress of the called party of the call.
The Called Party Numbering Plan and Calling Party Numbering Plan drop down lists correspondingly indicate the numbering plan of the called party's and calling party's number.
The Incoming Called Digits Size text field indicates the number of received digits (in a
range from 0 to 255) required to establish a call. When this field has a “0” value, the system
uses either the timeout defined in the T302 field or the Sending Complete Information
element messages to establish a call. Independent on the value in this field, Sending
Complete Information element and the pound sign always result in call establishment.
The Generate Progress tone on IP checkbox selection will generate the progress tone to
IP.
When Generate Progress Tone to PSTN/PBX checkbox is selected, Quadro generates
ring tones to callers during ISDN call dialing. This feature is mainly applicable to 2-stage dialing mode.
Enable CLIR Service checkbox selection enables Calling Line Identification Restriction
(CLIR) service which displays the incoming caller ID only if Presentation Indication is allowed on the remote side. Otherwise, if CLIR service is disabled, caller ID will be unconditionally displayed.
When the Alternative Disconnection Mode checkbox is not selected, Quadro will disconnect the call as soon as the disconnect message has been received from the peer. When
the checkbox is selected, Quadro’s user may hear a busy tone when peer has been disconnected.
The B1 Channel and B2 Channel checkboxes enables/disables timeslots for voice transfer.
Disabling the timeslot will prevent both incoming and outgoing calls.
Quadro4Li; (SW Version 5.2.x)
31
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Step 2-A: Using IP Lines
Before starting the IP Lines configuration, the appropriate IP phone should be connected to
the Quadro either to the WAN or LAN port. If the phones are placed on the Quadro WAN,
which is assumed by the default configuration, please ensure that the Connect IP phones
from WAN side checkbox is enabled on the Line Settings page (see Fig. l-24).
The Quadro4Li provides two options for configuring IP phones:
•
•
The Plug-and-Play option is available for supported SIP phones only. The list of
these phones is given below. The Plug-and-Play option does not require any
specific configuration except that the Enable PnP for IP lines checkbox should
be enabled on the Line Settings page (see Fig. l-24).
The Auto-Configuration option is available for tested and supported SIP
phones. The list of tested SIP phones is given below. The Auto-Configuration
option (described in detail below) requires specifying some basic parameters on
the Quadro and restarting the phone.
Please note: With the both options, IP phones download their configuration from the Quadro’s TFTP server. Therefore, if the phones obtain their network parameters from a DHCP
server other than the Quadro’s built-in DHCP server, please ensure that either the server
does not provide the “TFTP server” parameter or the parameter is set to the Quadro’s LAN
or WAN IP address depending on the location of IP phones.
When using the automatic-configuration option, each IP line should be configured individually from the Telephony menu, Line Settings page.
Open from the Telephony menu and choose Line Settings page. The IP Line Settings
page is displayed.
Fig. l-24: Line Settings page
Quadro4Li; (SW Version 5.2.x)
32
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Click on the IP Line number to enter the IP Lines Settings page.
Fig. l- 25: IP Line Settings page
Select the SIP Phone radio button. Select the SIP IP phone model from the Phone Model
drop-down list.
Please Note: If your IP phone is not listed in the Phone Model drop-down list, select the
Other option from the list to configure the SIP phone manually. The SIP phone’s configuration is different dependent on the SIP phone model. For more information about SIP Phone
configuration, refer to the SIP phone manual or user’s guide.
Insert the SIP Phone’s MAC address in the corresponding fields. The MAC address of an
IP phone is usually printed on the back of the phone’s base unit.
In the Line Appearances text box, enter the number for simultaneous calls supported by
the SIP IP phone – which is the sum of the number of active and held calls. For example, if
this field is set to 1, only one active call is possible to have on the phone and making or accepting a second call while the other is on hold will not be allowed. Note, that this number
depends on the phone brand and model, and cannot exceed the number of simultaneous
calls supported by the phone.
Username and Password are required to be inserted for this selection. They should match
on both Quadro and SIP phone for a successful connection. The Password field is checked
against its strength and you may see how strong is your inserted password right below that
field. To achieve the well protected strong password minimum 8 characters of letters in upper and lower case, symbols and numbers should be used. If you are unable to define a
strong password, press Choose Generated Password to use one of system defined
strong passwords.
The Transport drop down list is used to select the SIP protocol transport layer - UDP, TCP
or TLS. For TLS you may activate the TLS certificate update mechanism from IP Phone to
obtain the latest certificate generated by the Quadro.
The Use Session Timer enables the SIP session timer for the corresponding IP line. This
checkbox enables advanced mechanisms for connection activity checking. This option alQuadro4Li; (SW Version 5.2.x)
33
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
lows both user agents and proxies to determine if the SIP session is still active.
Reset the SIP Phone. After restart, the appropriate configuration will be automatically
downloaded from the Quadro to the SIP Phone.
Some SIP phones require only reboot for configuration download. Other SIP Phones may
require additional configuration. For example, by default IP Dialog SIP Tone II is in nonauto-provisioning mode, therefore the user has to manually enable it on the phone.
To make sure the IP line is configured properly, do the following:
•
Go to Quadro Status- SIP Registration status – Registered IP Lines to see if
IP Line registration is successful.
•
Dial *74 to get the line information.
•
Make outgoing and accept incoming calls.
Quadro4Li; (SW Version 5.2.x)
34
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
Supported SIP Phones
Below is the list of SIP phones that are officially supported by Epygi and can be configured
to work with Quadro4Li using its Plug-and-Play configuration option:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
snom 190,
snom 200,
snom 220,
snom 300 (also supports FVC),
snom 320 (also supports FVC),
snom 360 (also supports FVC),
snom 370 (also supports FVC),
snom 820 (also supports FVC),
snom 870 (also supports FVC),
snom MeetingPoint (also supports FVC),
Aastra 480i (also supports FVC),
Aastra 480iCT,
Aastra 9112i (also supports FVC),
Aastra 9133i (also supports FVC),
Aastra 9143i(33i)(also supports FVC),
Aastra 9480i(35i)(also supports FVC),
Aastra 9480iCT,
Aastra 6751i (also supports FVC),
Aastra 6753i (also supports FVC),
Aastra 6755i (also supports FVC),
Aastra 6757i (also supports FVC),
Aastra 6757iCT,
Aastra 6730i (also supports FVC),
Aastra 6731i (also supports FVC),
Polycom SoundPoint IP 300SIP,
Polycom SoundPoint IP 330SIP,
Polycom SoundPoint IP 331SIP,
Polycom SoundPoint IP 335SIP,
Polycom SoundPoint IP 450SIP,
Polycom SoundPoint IP 501SIP,
Polycom SoundPoint IP 550SIP,
Polycom SoundPoint IP 601SIP,
Polycom SoundPoint IP 650SIP,
Polycom SoundStation IP 6000,
Grandstream BT200,
Grandstream GXP2000,
Linksys SPA921,
Linksys SPA922,
Linksys SPA941,
Linksys SPA942,
Yealink T20,
Quadro4Li; (SW Version 5.2.x)
35
Quadro4Li Manual I: Installation Guide
•
•
•
Step 2: Configuring the Quadro
Yealink T22,
Yealink T26,
Yealink T28.
Tested SIP phones
Below is the list of SIP phones that are tested with the Quadro but may cause problems
when using some of the IP Phone related features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CISCO 7960
IpDialog ST201
Polycom SoundPoint IP 300SIP
Polycom SoundPoint IP 330SIP
Polycom SoundPoint IP 331SIP
Polycom SoundPoint IP 501SIP
Polycom SoundPoint IP 550SIP
Polycom SoundPoint IP 601SIP
Polycom SoundPoint IP 650SIP
Polycom SoundStation IP 6000
POLYCOM VVX 1500
SIPUra SPA 841
Snom 190
Snom 200
Snom 220
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Snom M3
Swissvoice IP 10S
Thomson ST 2030 SIP
Berkshire (ATL) 5000
Grandstream BT10
Grandstream BT200
Grandstream GXP2000
Linksys SPA921
Linksys SPA922
Linksys SPA941
Linksys SPA942
Yealink T28
Aastra MBU400
Telematrix IP550 Spectrum Plus
Telematrix 3300IP
Step 2-B: Using Key System Emulation
The Key System Emulation is a widely used service in legacy PBXs simplifying the direct
connection to the available PSTN lines. On the Quadro4Li, the usage of Key System Emulation services is limited to the IP phones attached to the Quadro through the available IP
lines and provides direct connection to the available PSTN lines and SIP networks. In its
turn, the IP phones are limited to the following models with the perspective to enlarge the
list of recommended IP phones in the future:
• Aastra 480i
• Aastra 57i
• Snom 370
• Aastra 9133i
• Snom 320
• Aastra 55i
• Snom 360
The Key System Emulation feature allows to:
•
Have a direct connection to the available PSTN lines and SIP networks behind
the Quadro by pushing the programmable keys on the IP phone.
•
Monitor the availability and status of all configured external lines via programmable keys on the IP Phones.
•
Place the call on hold from one IP phone and pick it from another IP phone attached on the Quadro.
Go to the Telephony menu of the Quadro’s Web Management for Key System Emulation
service configuration.
Quadro4Li; (SW Version 5.2.x)
36
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
By default, the 8 SLA lines of the Quadro4Li device are in inactive mode. To activate an
SLA line, assign an ISDN timeslot(s) or SIP number to the SLA line and configure the IP
phone’s programmable buttons.
Fig. l-26: Key System Emulation page
To assign an ISDN timeslot to an SLA, open the TelephonyÆKey system Emulation
page and click on the corresponding SLA line. The Key System Emulation page for the SLA
line opens (see Figure I-27). On this page, choose the PSTN radio button and select an
ISDN timeslot. For how to use SLA lines for SIP calls, see the section below.
To configure the IP phones to use the Key System Emulation service of the Quadro, the
programmable keys should be adjusted correspondingly. To do so, go to the Telephony
menu, Line Settings, move to the IP Line Settings page. If the IP Line is already configured, push the Advanced link for the corresponding IP line in the Details column, otherwise configure the IP line first as indicated in the chapter Step 2-A: Using IP Lines.
The Advanced link leads you to the Programmable Keys Configuration page where programmable keys for the corresponding IP phone can be configured. Assign the SLA line to
the preferred Programmable Key and save the settings. Once the corresponding IP phone
is restarted, the selected programmable key will be responsible for the calls on the configured SLA line. The corresponding programmable key will be blinking during incoming calls
on that SLA line. To make an outgoing call, the caller will simply need to push that programmable key to get access to the ISDN network (in default configuration, as indicated
above).
The Advanced Configuration link moves to the Advanced Configuration page that is
used to enable/disable the blind transfer service from SLA lines to extensions or their voice
mailboxes.
Please Note: By assigning an ISDN timeslot to an SLA line, it becomes unavailable for
calls through Auto Attendant or Call Routing Table. If you wish to leave ISDN timeslot
available for calls through the Auto Attendant or Call Routing Table, do not assign all ISDN
timeslots to SLAs.
Using SLA Lines for SIP Calls
You may want to use the SLA lines of the Key System Emulation for SIP calls through certain SIP servers instead of assigning them to the PSTN lines. To do so, go to the Key Sys-
Quadro4Li; (SW Version 5.2.x)
37
Quadro4Li Manual I: Installation Guide
Step 2: Configuring the Quadro
tem Emulation page from the Telephony menu of the Quadro’s Web Management. Push
the corresponding SLA line number to get its configuration page.
Fig. l-27: Key System Emulation – SLA# page
The SLA Name text field is used to insert the preferred name for the corresponding SLA
line. On the IP phones with the display available, this name is visible on the display next to
the programmable key.
A group of manipulation radio buttons allow you to configure the SLA line:
•
Inactive - disables the corresponding SLA line.
•
PSTN - allows you to assign the SLA line to the available PSTN lines on the Quadro. This selection disappears when there are no more unassigned PSTN lines
available.
Attention: By assigning a PSTN line to an SLA line, it becomes unavailable for
calls through Auto Attendant or Call Routing Table.
•
SIP - used to assign the SLA line to the certain SIP account. This selection has
two sub-selections:
o
Custom Settings - used to define a SIP server and SIP registration parameters. The following parameters are required for this selection:
Username - the registration username on the SIP server.
Password - the registration password on the SIP server.
SIP Server - the IP address or the host name of the SIP server.
SIP Port - the port of the SIP server.
Authentication User Name - an identification parameter to reach the SIP
server. It should be provided by the SIP service provider and can be requested for some SIP servers only. For others, the field should be left empty.
Outbound Proxy Host Address and Port - the IP address or the host
name and the port number of the outbound proxy SIP server.
Quadro4Li; (SW Version 5.2.x)
38
Quadro4Li Manual I: Installation Guide
o
Step 2: Configuring the Quadro
Use SLA Settings - choose this selection to use the SIP settings of another
SLA line. This selection is also used to allow multiple line appearances on
the same ITSP provider. The SLA drop down list is used to select the SLA
line whose SIP settings will be used for the corresponding SLA line. The
DID text field requires an optional identification number used by some ITSP
providers to differentiate between the call appearances on the selected line.
The Use DID for outgoing calls indicates whether the specified DID number should be included in the Caller ID of calls initiated from the SLA. If this
checkbox is enabled, the DID number will be sent along with the SIP username. This checkbox should be enabled if the IP-PSTN provider authorizes
the users by their DIDs.
For this configuration scenario, choose the SIP option with Custom Settings. Provide all
required information of the SIP server. Save the settings.
Now your SLA line will be handling calls through the defined SIP server. The IP phone can
be called by the SIP username of its SLA line. All incoming calls from that SIP server will be
blinking on the corresponding programmable key of the IP phone, as described in the previous chapter. For outgoing calls through the defined SIP server, the user should simply
push the programmable key assigned to the corresponding SLA line, and dial the SIP number of the called user.
Please Note: Quadro can also be configured in a mixed Key System Emulation mode, i.e.
having one SLA lines assigned to the SIP servers will still make possible to have others assigned to the available PSTN lines.
Disabling the Key System Emulation
To disable the Key System Emulation, disconnect the ISDN timeslot from the SLA by inactivating the SLA or by changing the SLA assignment to a SIP server. To do that, go to the
Key System Emulation page from the Telephony menu, push the SLA line to which the
corresponding ISDN line is assigned, choose the Inactive or SIP option and save the selection (in case of SIP, additional information should be provided as described above). Perform the same steps for other SLA lines, as needed. Now your SLA lines are available to
be used through the Auto Attendant and Call Routing.
Step 2-C: Using Receptionist
If you wish to use the Receptionist’s features, the Receptionist should be set up on the Quadro. The Quadro’s basic configuration should be done in the same way as described in
the Step 2.
The Receptionist related setup, with detailed instructions on how to configure the Quadro
and the attached IP Phones, is described in the “Receptionist Setup on Quadro” document, which you can find at the Epygi’s Web portal.
Quadro4Li; (SW Version 5.2.x)
39
Quadro4Li Manual I: Installation Guide
Step 3: Registering on Epygi’s Technical Support
Step 3: Registering on Epygi’s Technical Support
It is recommended that you register your Quadro on the Epygi Technical Support web
page. Registration will give you access to the Technical Support Database. There, you can
submit requests concerning technical problems as well as refer to the Frequently Asked
Questions (FAQ) section. In addition, the technical support page allows users to download
new firmware, manuals and other information. You can access the support section only if
you are registered. Additionally, registration at Epygi’s Technical Support web page gives
you the username and password to login to the Epygi SIP Server.
To register, you need to know the serial number of your Quadro, which is located on a label
on the bottom of Quadro. You will also need the date of purchase. Next, open the Epygi
home page (www.epygi.com), select Support and click on Registration Form. The online
registration page will appear:
Complete all fields and record
the Login Name and Password
in a safe place. You will need it
for the SIP server.
Please Note: In some cases, the
Quadro units will be shipped
preconfigured from the factory
with the Support login and password already set up. In this case,
an information sheet is included
in the packaged contents indicating the username and password
to access Epygi’s Online Support
and the Epygi SIP Server.
Fig. l- 28: Online Registration page
Quadro4Li; (SW Version 5.2.x)
40
Quadro4Li Manual I: Installation Guide
Step 4: Making/Receiving Calls
Step 4: Making/Receiving Calls
Please Note: The Quadro’s default settings are sufficient to make SIP phone calls. It
is not necessary to make any changes unless the user wants to create new SIP extensions on the Epygi SIP Server, create a private directory for several Quadro units,
or use alternate VoIP services. Refer to the Manual II - Administrator's Guide for
more information on these configurations.
• To make a call to the PSTN, dial 9 and the local phone number. You may accelerate
the dialing process by adding the # after the last digit, e.g., 9 + 972-661-1335#. You
are making a local call through the PSTN. It is assumed an ISDN trunk is connected to
the Quadro.
Please Note: In case you had changed the default value of the PSTN Access Code
in the System Configuration Wizard to something other than 9, you will need to dial
your chosen digit instead.
• To make a VoIP call to a user on the remote Quadro, lift the handset and dial 8 + SIP
Address (of the user on the remote Quadro) + #. You are calling over the Internet to a
remote user.
Please Note: Epygi has a SIP Address test line to test newly provisioned Quadro devices. Call 8 + 99 + # and you will hear a message if the call was successful. This
message comes from a Quadro in one of our offices. SIP Addresses are described below.
• Received IP calls will ring the extensions automatically.
• Received PSTN calls will be directed to the Quadro’s default Auto Attendant (00).
Using the Default SIP Addresses
Making Internet IP calls is simple with the Quadro. By default, every standard (analog) telephone connected to one of Quadro’s phone lines functions as an IP phone. If you open the
Extensions Management page, you will see that some SIP Addresses are available, one
attached to the Auto Attendant and one to each extension. These SIP addresses are the IP
telephone numbers of these extensions. Anyone with a Quadro or any other SIP IP device
on the Internet can place a call to SIPAddress@sip.epygi.com and the call will ring the
associated extension.
Under Extensions Management, you may edit the Display Names to assign extensions to
people.
Fig. l- 29: Extensions Management page
To do so, click on the box in the first column next to the extension to edit and click the Edit
Quadro4Li; (SW Version 5.2.x)
41
Quadro4Li Manual I: Installation Guide
Step 4: Making/Receiving Calls
button. When the page opens, go to General Settings and edit the Display Name and
click the Save button. Do not change any other settings at this time. For more information
on the Extensions Management settings, refer to the Administrator’s Guide and Appendix:
Registering on Epygi’s SIP Server of this document. The default SIP addresses are based
on internal parameters unique to each Quadro device. If the Quadro undergoes a factory
reset, the default addresses will be restored.
If you want to establish a dial plan between several Quadro units in a private group, refer to
Appendix: Registering on Epygi’s SIP Server, which describes how to change the default,
SIP addresses on the Epygi SIP server and in the Quadro devices. With the directory service, you can create a private directory accessible from the Internet using a username/password. This service is enabled through the Epygi SIP Server.
Quadro4Li; (SW Version 5.2.x)
42
Quadro4Li Manual I: Installation Guide
Appendix: Changing the Admin Password
Appendix: Changing the Admin Password
For security reasons, it is recommended that you change the default admin password. The
username of the administrator (admin) cannot be changed.
To change the administrator password, go to the System menu, User Rights Management.
Fig. l- 30: User Right Management page
Choose admin from the list and press the Change Password functional button from the
User Right Management page toolbar.
For Administrator account the page contains two parts - one for GUI Access Password,
the other one for Phone Access Password.
Fig. l- 31: Change Password page
The GUI Access Password offers the following components:
•
•
The Old Password field requires the current password of the Administrator. An
error message prevents entering the wrong password.
The New Password field requires a new password for the Administrator. Reentering the new password in the Confirm New Password field will confirm the
new password. Up to twenty (0-20) digits and symbols are allowed.
The Phone Access Password offers the following components:
•
•
The Old Password field requires the current password of the Administrator. An
error message prevents entering the wrong password.
The New Password field requires a new password for the Administrator. Reentering the new password in the Confirm New Password field will confirm the
new password. The password can consist of numeric values only. Up to twenty
Quadro4Li; (SW Version 5.2.x)
43
Quadro4Li Manual I: Installation Guide
Appendix: Changing the Admin Password
(0-20) digits are allowed. A corresponding warning appears if any other symbols
are inserted.
For Local Administrator or Extension accounts it offers the following components:
•
•
The Old Password field requires the current password of the Administrator. An
error message prevents entering the wrong password.
The New Password field requires a new password for the Administrator. Reentering the new password in the Confirm New Password field will confirm the
new password. The password can consist of numeric values only. Up to twenty
(0-20) digits are allowed. A corresponding warning appears if any other symbols
are inserted.
Note: If Administrator is changing the Local Administrator or Extension passwords or
Local Administrator is changing the Extension password then the Old Password field is
not displaying
Attention: It is highly recommended to define a proper and non-empty password on this
page if the extension is being used for the Call Relay service from the Quadro's Auto Attendant.
Write down the password somewhere and keep it in a secure place. If the password is lost,
a factory reset will be required on the unit (see Administrator's Guide, Hardware Overview).
All settings are lost after a factory reset. After a factory reset the default password (19) will
be restored.
Quadro4Li; (SW Version 5.2.x)
44
Quadro4Li Manual I: Installation Guide
Appendix: Configuring NAT Traversal
Appendix: Configuring NAT Traversal
NAT or Network Address Translation is a common feature used to expand the use of connected PCs and other networked devices without having to use multiple global Internet
public IP addresses. Most ISP’s will assign one public IP address to each customer that is
connected to the Internet. The customer can use a router to provide NAT capability and
create a private network of PCs and other devices not visible from the Internet. This
method offers security and also eliminates the need to assign global Internet public IP addresses to each device on the LAN.
The Quadro initiates and receives SIP calls from the Internet (or the network connected to
the WAN port). To receive SIP calls, the Quadro must be able to receive packets from the
SIP server or any other device that is trying to make an incoming call. If the Quadro is
placed behind a router with NAT, like most basic routers on the market today, the Quadro
will not be able to receive calls. To resolve this issue, either STUN must be enabled on the
Quadro or SIP NAT traversal must be set up in the router and in the Quadro to route the incoming calls properly.
Please Note: NAT traversal only works with Internet connections that have static IP addresses. Verify from your provider that this is the case for your Internet connection. Some
ISPs provide dynamic IP addresses that may change from time to time, and are not appropriate for SIP NAT traversal.
Please Note: If you have more than one router in series between the Quadro and the Internet, the same port forwarding setup must be configured on each router.
NAT Traversal Setup
•
Install the Quadro behind the router. If the Quadro is configured with its factory default
settings, it is already configured for DHCP and will obtain an IP address automatically
from the router.
•
Connect a PC to the Quadro LAN port and power it up.
•
Verify the Quadro can connect to the Internet by opening a browser window and
browsing to a familiar WEB site. If the Quadro cannot reach the Internet, verify the
LAN/WAN LEDs and the cabling. Verify the Quadro is set up for DHCP on the WAN
and that the router has the DHCP server enabled for the devices behind it.
•
Find the address of the router and log into the router. Refer to the router’s user manual
on how to open the router configuration.
•
Set up port forwarding on the router to forward UDP ports 5060, 6000-6099 to the IP
address assigned to the Quadro. You can see the IP address of the Quadro in the
System menu under Status, submenu Network Status. The IP address will be listed as
the WAN IP address. Your router also may indicate the IP address assigned to the
Quadro.
•
Find out the public Internet address (WAN IP address) of the router. To do so, open a
browser and go to www.whatismyip.com. The site will return your public Internet IP
address. Record this IP address.
•
From the Telephony menu of the Quadro Management go to the NAT Traversal Settings page, go to General Settings and set the enable NAT Traversal for SIP radio
buttons selection to Force. Save the selection.
Quadro4Li; (SW Version 5.2.x)
45
Quadro4Li Manual I: Installation Guide
Appendix: Configuring NAT Traversal
Fig. l- 32: NAT Traversal Settings – General Setting
Go to SIP Parameters page.
Fig. l- 33: NAT Traversal Settings - SIP Parameters
Select Use Manual NAT Traversal and enter the WAN IP address of the router into the
Mapped Host text field. For Mapped Port, enter the router's corresponding port number, in this case 5060. Save the entries.
•
Go to the RTP Parameters page and select Use Manual NAT Traversal.
Fig. l- 34: NAT Traversal Settings - RTP Parameters
•
Enter the WAN IP address of the router into the Mapped Host text field. Set the
Mapped RTP/RTCP Port Range according to the values specified on the router, in
this case to 6000 (Min) and 6099 (Max), respectively. Click the Save button to save
the contents.
The Quadro will activate the settings and register the extensions on the Epygi SIP Server
after a few minutes. You can verify the settings from the main Quadro Management menu
under Status in the SIP Registration Status section.
Quadro4Li; (SW Version 5.2.x)
46
Quadro4Li Manual I: Installation Guide
Appendix: Configuring NAT Traversal
Appendix: Registering on Epygi’s SIP Server
You may login directly to Epygi’s SIP Server if you have registered your Quadro at Epygi’s
Technical Support Center. If you have not registered with Epygi Technical Support, you
cannot login to the Epygi SIP Server.
Log in to the Epygi SIP Server at www.epygi.com. Click on SIP, Login here. Use the same
login name and password you used for Epygi Support for Customer Login.
Fig. l- 35: SIP Services Login page
Read the SIP Service Terms and Conditions and accept it to proceed. The displayed
page now welcomes you and allows you to Subscribe a New Extension.
Fig. l- 36: SIP Services Welcome page
Selecting Subscribe a New Extension leads you to a page where you can enter the user
information as shown below. The Extension Nr. is the eight-digit SIP number assigned to
your extension. The first five are fixed by the SIP Server and cannot be changed and the
last three are user defined. Notice the check box to enable this extension to be shown in
the Epygi Public SIP Directory.
Please Note: If you enable this extension to be shown in the Epygi Public SIP Directory,
all information related to this extension will be published in the Public SIP Directory, which
is accessible by anyone from the Internet. To maintain privacy, do not check this box.
Quadro4Li; (SW Version 5.2.x)
47
Quadro4Li Manual I: Installation Guide
Appendix: Configuring NAT Traversal
Fig. l- 37: SIP Services Add New Extension page
The Authentication password validates the entry and must match the password entered
on the Quadro later. Make sure to record the name, Authentication Password and SIP extension number for entry into the Quadro later.
Save will store the entered information and conclude the basic SIP registration. The following page then will be displayed:
Fig. l- 38: SIP Services Your Extension page
This table shows unreg. in the Stat. column. This entry will change to reg. when the required settings in the Quadro are complete and the Quadro successfully registers on the
SIP Server.
Repeat this for all four extensions on the Quadro and the Auto Attendant.
Quadro4Li; (SW Version 5.2.x)
48
Quadro4Li Manual I: Installation Guide
Appendix: Registering on Epygi SIP Server
Configuring Quadro Extensions
Once the SIP server has the created extensions with the user information, create these extensions in the Quadro devices. Once they are entered in the Quadro, they will be registered and can then be used.
Login into the Quadro and go to Extensions Management.
Fig. l- 39: Extensions Management page
Select the first extension to change by clicking the appropriate checkbox and press Edit
functional button. The Extensions Management – Edit Entry page will be displayed.
Go to the General Settings page and adjust the Display Name as needed.
Fig. l- 40: Extensions Management - Edit Entry – General Settings page
Go to the SIP Settings page to enter the SIP Registration Settings you received from the
Epygi SIP server.
Quadro4Li; (SW Version 5.2.x)
49
Quadro4Li Manual I: Installation Guide
Appendix: Registering on Epygi SIP Server
Fig. l- 41: Extensions Management - Edit Entry – SIP Settings page
•
Enter the SIP registration number displayed in the column Ext# into the text field
Registration User Name.
•
In the Password field, enter the password you specified when registering at the
SIP server and confirm it in the field below.
•
In Registration SIP Server, the selected SIP server address must be entered. If
you use the Epygi SIP server, you may leave the default entry sip.epygi.com.
•
Most SIP server providers, including Epygi, use port 5060 as the Registration SIP
Port. You may leave the default entry as is.
•
Select Registration on SIP Server if you want to establish and receive IP calls.
•
Click the Save button to activate the settings.
Other settings of the extension might be also modified from Extensions Management –
Edit Entry page (refer to the Manual II - Administrator’s Guide).
Your settings will be verified, then after a few seconds the Extensions Management page
is updated with the changes as shown in the below example, Fig.I-42.
Fig. l- 42: Extensions Management page
If you go back to Epygi’s SIP Server, you will find the value reg. for this number in the column Stat. Reg. This will indicate that the Quadro has successfully registered the new number. If this does not happen after a few minutes, again verify the SIP Number and passwords.
Quadro4Li; (SW Version 5.2.x)
50
Quadro4Li Manual I: Installation Guide
Appendix: Checking the Connections
Appendix: Checking the Connections
If the system doesn’t seem to be working properly, even when all the cables are connected
properly, it may be helpful to Start Network Diagnostics: The WAN link, IP configuration,
gateway, DNS server, and STUN-NAT will all be checked.
To start diagnostics, open the System's menu item Diagnostics and click Start Network
Diagnostics.
Fig. l- 43: System Diagnostics - Network Diagnostics page
If the test passes, the output of the system may look as follows:
Basic Tests:
Checking for physical link:
WAN link ok
Checking IP configuration:
dynamically via DHCP Client
DHCP Client is running
Checking internet connectivity (ICMP ping):
Gateway:
reached
Primary nameserver:
reached
Secondary nameserver: not configured
www.epygi.com:
reached
STUN Network Address Translation (NAT) Check:
External visibible address: 212.126.210.179
Detected NAT type
: Restricted cone
Performing MTU Discovery:
preparing system
Sending UDP Datagram of size 1500
got answer
clean up
Largest usable MTU size is: 1500 Bytes
Test successful.
Depending on where the test is failing, the diagnostic can give some advice on how to
solve the problem. See the example below of a failed test:
Basic Tests:
Checking for physical link:
no WAN link
Please check the physical connection of the WAN interface. Cable not
plugged or broken?
Test failed.
Quadro4Li; (SW Version 5.2.x)
51
Quadro4Li Manual I: Installation Guide
Appendix: Checking the Connections
If diagnostics are successful, but you are still unable to place a call to 899# then check the
SIP registration status.
Open the SIP Registration Status page using the Quadro management System menu item
Status. Besides the SIP registration information for the auto attendant and each connected
extension, the Detected Connection Type is shown. If Quadro is placed behind a NAT
router and the STUN is enabled, the detected connection type and the IP address of this
router's WAN port are displayed.
Fig. l- 44: SIP Registration Status page
Quadro cannot work behind your router if Detected Connection Type is one of the following:
•
Unknown connection - unexpected error
•
Symmetric NAT
•
Symmetric Firewall
•
Blocked UDP
If you get one of the above mentioned Detected Connection Types, either connect the Quadro in front of the router, or configure NAT traversal manually as explained in Appendix:
Configuring NAT Traversal.
If you are unable to resolve your problems, please send us a technical support request on
the Support section of http://www.epygi.com/. Please prepare a system log file and attach it to your request.
To download the system logs, open the System Diagnostics page from System menu Diagnostics and click Download System Logs.
Quadro4Li; (SW Version 5.2.x)
52
Quadro4Li Manual I: Installation Guide
Appendix: Pin Assignment of ISDN
Appendix: Pin Assignment of ISDN
Pin
Signal
1
N.C.
2
N.C.
3
SSR1
4
SSX1
5
SSX2
6
SSR2
7
N.C.
8
N.C.
Fig. l- 45: Pin Assignment of ISDN in User mode
Pin
Signal
1
N.C.
2
N.C.
3
SSX1
4
SSR1
5
SSR2
6
SSX2
7
N.C.
8
N.C.
Fig. l- 46: Pin Assignment of ISDN in Network mode
Quadro4Li; (SW Version 5.2.x)
53
Copyright 2003 - 2011
Epygi Technologies, Ltd.
All rights reserved
QIG-QUADRO-10-04
Download PDF
Similar pages