http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 376315150 892498299
RMT-V403/V404
SERVICE MANUAL
Chile Model
Peru Model
SLV-LX700S
1
2
3
4
5
6
7
8
9
Mexican Model
SLV-LX500/LX600S/LX700S
0
TEL
TEL
TS-10 MECHANISM
Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENT MANUAL VII for MECHANICAL
QQ 3763 1515 0 89 2498 299
SPECIFICATIONS
System
Inputs and outputs
General
Format
VHS NTSC standard
Video recording system
Rotary head helical scanning FM system
Video heads
Double azimuth four heads
Video signal
NTSC color, EIA standards
Tape speed
LINE IN 1 (entrada de línea 1) and LINE-2 IN (entrada de
línea 2)
VIDEO IN (entrada de video), phono jack (1 each)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN (entrada de audio), phono jacks (2 each)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE OUT (salida de línea)
VIDEO OUT (salida de video), phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO OUT (salida de audio), phono jacks (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
Power requirements
SLV-LX700S CS
110 – 240 V AC, 50/60 Hz
Other models
120 V AC, 60 Hz
Power consumption
16 W
Operating temperature
0°C to 45°C (32°F to 113°F)
Storage temperature
–20°C to 60°C (–4°F to 140°F)
Dimensions including projecting parts and controls
(w/h/d)
SLV-LX700S/SLV-LX600S
Approx. 360 × 95 × 258 mm
SLV-LX500
Approx. 360 × 95 × 250 mm
Mass
Approx. 2.6 kg
SP: 33.35 mm/s (1
3
8
inches/s)
EP: 11.12 mm/s ( 7 16 inches/s)
LP: 16.67 mm/s ( 11 16 inches/s),
playback only
Maximum recording/playback time
8 hrs. in EP mode (with T-160 tape)
Rewind time
Approx. 1 min (with T-120 tape)
Timer section
Tuner section
Channel coverage
VHF 2 to 13
UHF 14 to 69
CATV A-8 to A-1, A to W, W+1 to W+84
Antenna
75-ohm antenna terminal for VHF/UHF
Clock
Quartz locked
Timer indication
12-hour cycle
Timer setting
8 programs (max.)
Supplied accessories
Remote commander (1)
Size AA (R6) batteries (2)
75-ohm coaxial cable with F-type connectors (1)
Plug adaptor (1)
(SLV-LX700S CS only)
Audio/video cable (3-phono to 3-phono) (1)
(SLV-LX700S and SLV-LX600S only)
Design and specifications are subject to change without
notice.
www
x iao y u163. co m
VIDEO CASSETTE RECORDER
.
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
QQ
QQ
ADJUSTMENTS. (9-921-790-11)
13942296513
13942296513
Photo: SLV-LX700S
RMT-V404
http://www.xiaoyu163.com
QQ 376315150 892498299
TEL
TEL
13942296513
13942296513
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
5. Check the B+ voltage to see it is at the values specified.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to
the customer and recommend their replacement.
www
x iao y u163. co m
SAFETY-RELATED COMPONENT WARNING!!
.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
—2—
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
SAFETY CHECK-OUT
QQ
QQ
QQ 3763 1515 0 89 2498 299
TEL 13942296513
http://www.xiaoyu163.com
QQ 376315150 892498299
Important Service Guide
TABLE OF CONTENTS
2. Disassembly
◆ Mode Switch (Program Switch) Assembly Point ························· 4
◆ How to eject the cassette tape
(If the tape is stuck in the unit) ·············································· 4
1.
2-1
2-2
2-3
2-4
Cabinet Top ········································································
Ass’y-Panel Front ·······························································
Ass’y Jack-PCB ··································································
Ass’y Jack-Main, Deck ······················································
2-1
2-1
2-2
2-3
3.
P.C.Boards
3-1
3-2
Main PCB ··········································································· 3-3
Function PCB ····································································· 3-7
4.
Schematic Diagrams
General
5.
Alignment and Adjustment
5-1
5-1-1
5-1-2
5-2
5-2-1
5-2-2
5-3
Reference ············································································
Location of adjustment button of remote control ···············
Test point location for adjustment mode setting ················
Mechanical Adjustment ······················································
The number and position of test point ································
ACE Head Position (X-Point) Adjustment ·························
Head Switching Point Adjustment ·····································
Exploded Views ··································································
Instrument Assembly ··························································
Mechanical Parts (Top Side) ··············································
Mechanical Parts (Bottom Side) ·········································
Electrical Parts List ····························································
• Abbreviation
CS: Chile model, Peru model
MX: Mexican model
www
.
x iao y u163. co m
—3—
http://www.xiaoyu163.com
6-2
6-2
6-3
6-4
6-5
376315150 892498299
376315150 892498299
Repair Parts List
6-1
6-1-1
6-1-2
6-1-3
6-2
QQ
QQ
QQ 3763 1515 0 89 2498 299
6.
5-1
5-1
5-2
5-3
5-3
5-3
5-4
13942296513
13942296513
TEL 13942296513
◆ Block Identification of Main PCB ············································ 4-3
4-1 S.M.P.S./Power (MX) ························································· 4-5
4-2 S.M.P.S./Power (CS) ·························································· 4-7
4-3 Logic/Display ····································································· 4-9
4-4 Audio/Video ····································································· 4-11
4-5 Hi-Fi/MTS ········································································ 4-13
4-6 TM-Block/Input-Output ··················································· 4-15
TEL
TEL
Getting Started
Step 1 : Unpacking ····························································· 1-1
Step 2 : Setting up the remote commander ························· 1-1
Step 3 : Hookups ································································ 1-2
Step 4 : Setting the clock ···················································· 1-4
Step 5 : Selecting a language ·············································· 1-4
Step 6 : Presetting channels ················································ 1-4
Basic Operations
Playing a tape ····································································· 1-5
Recording TV programs ····················································· 1-6
Recording TV programs using the Dial Timer ··················· 1-7
Recording TV programs using the timer ···························· 1-8
Locking the VCR (Child Lock) ·········································· 1-9
Additional Operations
Playing/searching at various speeds ··································· 1-9
Setting the recording duration time ···································· 1-9
Checking/changing/canceling timer settings ···················· 1-10
Recording stereo and bilingual programs ························· 1-10
Searching using various functions ···································· 1-10
Adjusting the picture (tracking) ······································· 1-11
Changing menu options ···················································· 1-11
Editing with another VCR ················································ 1-12
Additional Information
Antenna information ························································· 1-12
Troubleshooting ································································ 1-12
Index to parts and controls ··············································· 1-13
Index ················································································· 1-14
Quick reference to using the VCR ·············································· 1-14
http://www.xiaoyu163.com
1515SERVICE
0 8GUIDE
9 249 82 99
QQ 3763IMPORTANT
◆ MODE SWITCH (PROGRAM SWITCH) ASSEMBLY POINT
1) When installing the ass’y deck on the Main PCB, be sure to align the assembly point of mode switch.
TEL
TEL
Fig. 1
QQ 3763 1515 0 89 2498 299
1) Turn the Gear Worm 1 clockwise in the direction of arrow with a screwdriver. (See Fig. 2)
(Other method ; Remove the screw of Motor Load Ass’y, Separate the Motor Load Ass’y)
2) When Slider S, T approached the unloading position, rotate holder Clutch counterclockwise after inserting screwdriver in the frame’s bottom hole
in order to wind the unwound tape. (Refer to Fig. 3)
(If you rotate Gear Worm 1 continuously when tape is in state of unwinding, you may cause tape contamination by grease and tape damage. Be
sure to wind the unwound tape in the state of set horizontally.)
3) Rotate Gear Worm 1 clockwise using screwdriver again up to the state of eject mode and then pick out the tape. (Refer to Fig. 2)
1 GEAR WORM
FRAME
www
.
Fig. 2
x iao y u163. co m
Fig. 3
—4—
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
QQ
QQ
◆ HOW TO EJECT THE CASSETTE TAPE
(If the tape is stuck in the unit)
13942296513
13942296513
ASSEMBLY POINT
(ALIGN TWO ARROWS)
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 376315150 892498299
1. GENERAL
This section is extracted from instruction manual.
(3-081-607-E1)
Getting Started
Step 1 : Unpacking
Step 2 : Setting up the remote commander
Inserting the batteries
• Remote commander
Getting Started
Check that you have received the following items with the VCR:
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
• 75-ohm coaxial cable with F-type connectors
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
• Size AA (R6) batteries
• Audio/video cable (3-phono to 3-phono)
(SLV-LX700S and SLV-LX600S only)
Using the remote
commander
• Plug adaptor (SLV-LX700S CS only)
Remote sensor
TEL
TEL
•TV / VIDEO
13942296513
If the plug supplied with your VCR does not fit
your power outlet, attach the supplied adaptor
to the plug.
Check your model name
To operate
The instructions in this manual are for the 4 models: SLV-LX700S MX/CS, SLV-LX600S
MX and SLV-LX500 MX. Check your model name by looking at the rear panel of your
VCR.
SLV-LX700S MX is the model used for illustration purposes. Any difference in operation
is clearly indicated in the text, for example, “SLV-LX700S MX only.”
2
3
4
5
6
Set •TV / VIDEO to
the VCR
VIDEO and point at the remote sensor at the VCR
a Sony TV
•TV and point at the remote sensor at the TV
QQ
QQ
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Setting up the remote commander
Controlling other TVs with the remote commander
(not available on SLV-LX500)
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programed to work with the
VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
• When you press the AUDIO MONITOR (monitor de audio) button, your TV’s menu may
appear on the TV screen. To exit the TV menu, press the MENU button on the TV remote
commander or wait until the menu disappears automatically.
The remote commander is preprogramed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
1 Set •TV / VIDEO at the top of the remote commander to •TV.
down ?/1, and enter your TV’s code number using the number buttons.
2 Hold
Then release ?/1.
Now you can use the ?/1, VOL (volumen) +/–, CH (canal) +/–, and TV/VIDEO
buttons to control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the VCR, reset •TV / VIDEO to VIDEO.
5
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
TV brand
Code number
TV brand
Sony
01
Panasonic
06, 19
Akai
04
Philco
03, 04
AOC
04
Philips
08
Centurion
12
Pioneer
16
Coronado
03
Portland
03
Curtis-Mathes
12
Quasar
06, 18
Daytron
12
Radio Shack
05, 14
Emerson
03, 04, 14
RCA
04, 10
Fisher
11
Sampo
12
General Electric
06, 10
Sanyo
11
Gold Star
03, 04, 17
Scott
12
Hitachi
02, 03
Sears
07, 10, 11
J.C.Penney
04, 12
Sharp
03, 05, 18
www
JVC
KMC
Magnavox
Marantz
MGA/Mitsubishi
NEC
6
.
Code number
x iao y u163. co m
09
Sylvania
08, 12
03
Teknika
03, 08, 14
03, 08, 12
Toshiba
07
04, 13
Wards
03, 04, 12
04, 12, 13, 17
Yorx
12
04, 12
Zenith
15
Setting up the remote commander
1-1
http://www.xiaoyu163.com
Setting up the remote commander
7
376315150 892498299
continued
Unpacking
Getting Started
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
4
1
13942296513
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with a
dot (•) can be used to operate your
Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
http://www.xiaoyu163.com
QQ 376315150 892498299
Audio/video (A/V) hookup
Step 3 : Hookups
If your TV has audio/video (A/V) input jacks, you will get a better picture and sound
if you hook up your VCR using these connections. If your TV does not have A/V
inputs, see the following pages for antenna or cable hookups.
If you are not planning to use your VCR to record programs, you finished setting up
the VCR after you have made the connections shown on this page. If you want to
record regular or cable TV programs, complete these connections first, and then go to
the following pages for antenna or cable hookups.
There are many ways in which your VCR can be hooked up. To hook up your VCR
so that it works best for you, first scan through the table below. Then use the
accompanying diagrams and procedures on the following pages to set up your VCR.
If your TV has audio/video inputs, refer to pages 9 and 10 for audio/video (A/V)
hookup. Then follow one of the hookups below. If your TV does not have A/V
inputs, do directly to one of the hookups below.
If you have
Use
Refer to
Antenna only, no cable TV
Hookup 1
(Plug and Play
(enchufar y ajustar))
Pages 11 and 12
No cable box or cable box with only a
few scrambled channels
Hookup 2
(Plug and Play
(enchufar y ajustar))
Pages 13 and 14
Cable box with many scrambled
channels
Hookup 3
For SLV-LX700S and SLV-LX600S
For a true “home theater” experience, you should connect the audio outputs of your
VCR or TV to your stereo system.
Getting Started
Selecting the best hookup option
A Use this hookup if your TV has stereo jacks
Stereo receiver
VCR
TV
LINE LINE
OUT IN 1
AUX IN
AUDIO
VIDEO
IN
VIDEO
AUDIO OUT
AUDIO
Page 15
After you have completed the connections, follow the instructions for setup.
Audio/video cable (supplied)
Audio cable (not supplied)
TEL
TEL
After you have completed the setup, you are ready to use your VCR. Procedures
differ depending on the hookup you used. For an overview, refer to “Quick reference
to using the VCR” on the back cover.
B Use this hookup if your TV does not have stereo jacks
Stereo receiver
VCR
TV
LINE LINE
OUT IN 1
AUX IN
AUDIO
13942296513
13942296513
Before you get started
• Turn off the power to all equipment.
• Do not connect the AC power cords until all of the connections are completed. If
you connect the AC power cord before the connections are completed, you may not
be able to use the Plug and Play (enchufar y ajustar) function.
• Be sure you make connections firmly. Loose connections may cause picture
distortion.
• If your TV does not match any of the examples provided, see your nearest Sony
dealer or qualified technician.
VIDEO
IN
VIDEO
AUDIO
Video cable (not supplied)
Audio cable (not supplied)
Notes
• To play a tape in stereo, you must use the A/V connection.
• If you do not have a stereo receiver, connect the white LINE OUT/AUDIO L (salida de línea/
audio izquierda) jack to the AUDIO IN (entrada de audio) jack on your TV.
• If you use the Trinitron TV Synchro Play function (page 25), the A/V connection is
necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO
IN 1 (entrada de video 1) jacks.)
Hookups
Hookup 1 (Plug and Play (enchufar y ajustar))
A Use this hookup if your TV has stereo jacks
Antenna hookup
VCR
Make the following connections if you are using an antenna (if you do not have cable
TV).
TV
AUDIO
OUT IN
A Use this hookup if you are using:
• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
IN
VIDEO
VIDEO
AUDIO
Rear of TV
VHF/UHF
Audio/video cable (not supplied)
B Use this hookup if your TV does not have stereo jacks
or
VCR
VCR
A Match the type of
connector on your
TV: A, B, or C.
VHF
B
TV
AUDIO
OUT IN
IN
OUT
UHF
or
VHF
IN
VIDEO
VIDEO
C
AUDIO
UHF
Audio/video cable (not supplied)
B Use this hookup if you are using a VHF-only antenna (you get
channels 2–13 only)
Note
• If you use the Trinitron TV Synchro Play function (page 25), the A/V connection is
necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO
IN 1 (entrada de video 1) jacks.)
Rear of TV
VHF/UHF
A
or
VCR
IN
OUT
or
VHF
B
UHF
VHF
10
www
Hookups
Match the type of
connector on your
TV: A, B, or C.
For connector types
B and C, no UHF
connection is
required.
x iao y u163. co m
C
UHF
.
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external
antenna connector (not supplied) so you can connect the cable to the RF IN (entrada
de radiofrecuencia) connector. If you have separate cables for VHF and UHF
antennas, you should use a U/V band mixer (not supplied) (page 50).
1-2
http://www.xiaoyu163.com
continued
Hookups
11
376315150 892498299
For SLV-LX500
9
Getting Started
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Hookups
QQ
QQ
continued
8
http://www.xiaoyu163.com
QQ 376315150
89 249 82 99
Hookup 1 : VCR setup
Hookup 2 (Plug and Play (enchufar y ajustar))
Plug the VCR into the AC outlet.
You have no cable box, or a cable box with only a few
scrambled channels
The VCR automatically presets the TV channels when the VCR is plugged into
the AC outlet.
AC power cord
What you can do with this hookup
• Record any unscrambled channel by selecting the channel on the VCR
to AC outlet
Getting Started
Recommended use
Use this hookup if you do not have a cable box. Also use this hookup if your cable
system scrambles only a few channels.
What you cannot do
The VCR starts presetting the channels.
• Record scrambled channels that require a cable box
VCR
Rear of TV
VHF/UHF
Wall
You have now completed VCR setup.
IN
A Match the type
of connector
on your TV: A,
B, or C.
VHF
OUT
To change the on-screen display language, see “Step 5 : Selecting a language” on
page 18.
or
To add or disable channels manually, see “Presetting/disabling channels
manually” on page 21.
Connect this cable
directly to your TV if
you do not have a
cable box.
B For connector
types B and C,
no UHF
connection is
VHF
required.
UHF
or
Cable box
TEL
TEL
Notes
• If you connect the AC power cord before the antenna connections are completed, the
channels may be incorrectly set. If this happens, see “Step 6 : Presetting channels” on
page 19.
• Do not press any buttons on the VCR or remote commander during Auto preset.
• Auto preset starts automatically only when you plug in the AC power cord for the first time
after you purchase the VCR.
• Auto preset can be performed by pressing x STOP (parada) continuously for 5 seconds or
more with the VCR power turned off.
C
IN
UHF
OUT
13942296513
13942296513
Hookups
Hookup 3
Plug the VCR into the AC outlet.
Connecting a cable box with many scrambled channels
The VCR automatically presets the TV channels when the VCR is plugged into
the AC outlet.
Recommended use
Use this hookup if your cable system scrambles all or most channels.
What you can do with this hookup
• Record any channel by selecting the channel on the cable box
AC power cord
What you cannot do
• Record with the cable box turned off
• Record one channel while watching another channel
to AC outlet
The VCR starts presetting the channels.
Cable box
Wall
Rear of TV
VHF/UHF
IN
OUT
A
Match the type of
connector on your
TV: A, B, or C.
B
For connector
types B and C, no
UHF connection
is required.
You have now completed VCR setup.
or
To change the on-screen display language, see “Step 5 : Selecting a language” on
page 18.
VHF
To add or disable channels manually, see “Presetting/disabling channels
manually” on page 21.
or
Notes
• If you connect the AC power cord before the antenna connections are completed, the
channels may be incorrectly set. If this happens, see “Step 6 : Presetting channels” on
page 19.
• Do not press any buttons on the VCR or remote commander during Auto preset.
• Auto preset starts automatically only when you plug in the AC power cord for the first time
after you purchase the VCR.
• Auto preset can be performed by pressing x STOP (parada) continuously for 5 seconds or
more with the VCR power turned off.
UHF
VHF
VCR
C
IN
OUT
UHF
After you have completed hookup…
After you have completed hookup, plug the VCR into the AC outlet and see
“Step 5 : Selecting a language” on page 18.
www
14
Hookups
x iao y u163. co m
AC power cord
.
to AC outlet
1-3
http://www.xiaoyu163.com
Hookups
15
376315150 892498299
Hookup 2 : VCR setup
13
Getting Started
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Hookups
QQ
QQ
continued
12
http://www.xiaoyu163.com
QQ 376315150 892498299
Press M/m to set the day.
3
Step 4 : Setting the clock
AJUSTE DEL RELOJ
PLAY
FECHA AÑO
HORA
2 8 / 1 2 0 0 3 MAR 12 : 0 0 AM
OK
Escoger : Bb
Fin
: OK
Before you start…
• Turn on the VCR and the TV.
• Set the “Salida video” to “3CH (canal3)”
or “4CH (canal4)” in the OPCIONES
AVANZADAS menu, whichever channel is
not used in your area. If both are used, set
the “Salida video” to either channel
(page 47). If your TV is connected to the
VCR using A/V connections, set the TV to
video input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
4
PLAY
MENU
Press , to flash the month and press M/m to
set the month.
Ajustar : Vv
Salir
: MENU
AJUSTE DEL RELOJ
FECHA AÑO
HORA
2 8 / 9 2 0 0 3 DOM 12 : 0 0 AM
OK
Escoger : Bb
Fin
: OK
M/m/</,
OK (aceptación)
5
Getting Started
Set the time and date to use the timer feature
for recording programs.
Ajustar : Vv
Salir
: MENU
Set the year, hour, and minutes in the same way as the month.
The day of the week is set automatically.
6
Press OK (aceptación) or MENU to start the clock.
PLAY
OK
MENU
MENU
Press MENU.
TEL
TEL
1
MENU PRINCIPAL
Prog. / Verif.
Ajuste del reloj
Preajuste sintonizador
Opciones Avanzadas
Language / Idioma
2
PLAY
Press M/m to move the cursor (B) to “Ajuste
del reloj,” then press OK (aceptación).
AJUSTE DEL RELOJ
Escoger : Bb
Fin
: OK
HORA
12 : 0 0 AM
Ajustar : Vv
Salir
: MENU
Setting the clock
Step 6 : Presetting channels
You can change the on-screen display
language.
This VCR is capable of receiving VHF
channels 2 to 13, UHF channels 14 to 69 and
unscrambled CATV channels 1 to 125. First,
we recommend that you preset the receivable
channels in your area using automatic
presetting methods. Then, if there are any
unwanted channels, disable them manually.
If you have already decided which channels
you wish to preset, set them directly using
manual presetting methods (page 21).
Before you start…
• Turn on the VCR and the TV.
• Set the “Salida video” to “3CH (canal3)”
or “4CH (canal4)” in the OPCIONES
AVANZADAS menu, whichever channel is
not used in your area. If both are used, set
the “Salida video” to either channel
(page 47). If your TV is connected to the
VCR using A/V connections, set the TV to
video input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
1
MENU
MENU
M/m/,
OK (aceptación)
Press MENU.
2
PLAY
Before you start…
• Turn on the VCR and the TV. When using
a cable box, turn it on.
• Set the “Salida video” to “3CH (canal3)”
or “4CH (canal4)” in the OPCIONES
AVANZADAS menu, whichever channel is
not used in your area. If both are used, set
the “Salida video” to either channel
(page 47). If your TV is connected to the
VCR using A/V connections, set the TV to
video input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
MENU PRINCIPAL
Press M/m to move the cursor (B) to
“Language/Idioma.”
OK
MENU PRINCIPAL
PLAY
www
OK
18
1
MENU
Press MENU.
MENU
Selecting a language
Escoger : Vv
Ajustar : OK
x iao y u163. co m
2
PLAY
Press MENU to exit the menu.
.
MENU PRINCIPAL
Prog. / Verif.
Ajuste del reloj
Preajuste sintonizador
Opciones Avanzadas
Language / Idioma
Salir : MENU
Press , to select the desired language, English or Spanish.
3
4
Salir : MENU
Prog. / Verif.
Ajuste del reloj
Preajuste sintonizador
Opciones Avanzadas
Language / Idioma
Escoger : Vv
Ajustar : b
M/m/</,
OK (aceptación)
Presetting all receivable
channels automatically
Prog. / Verif.
Ajuste del reloj
Preajuste sintonizador
Opciones Avanzadas
Language / Idioma
Escoger : Vv
Ajustar : OK
MENU
Press M/m to move the cursor (B) to “Preajuste
sintonizador,” then press OK (aceptación).
OK
PREAJUSTE SINTONIZADOR
[ CABLE ]
Ant / Cable:
Ajuste automático
Añadir / Borrar canales
Escoger : Vv
Fin
: OK
1-4
http://www.xiaoyu163.com
Salir : MENU
Ajustar : Bb
Salir
: MENU
continued
Presetting channels
19
376315150 892498299
Step 5 : Selecting a language
17
Getting Started
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Setting the clock
QQ
QQ
16
Salir : MENU
FECHA AÑO
0 1 / 1 2 0 0 3 MIE
OK
13942296513
13942296513
Escoger : Vv
Ajustar : OK
http://www.xiaoyu163.com
QQ 376315150 892498299
Presetting/disabling channels manually
Press M/m to move the cursor (B) to “Ant/Cable.”
3
OK
4
• To preset cable TV channels:
Press </, to select CABLE.
PLAY
PREAJUSTE SINTONIZADOR
[ CABLE ]
Ant / Cable:
Ajuste automático
Añadir / Borrar canales
OK
Escoger : Vv
Fin
: OK
• To preset VHF and UHF channels:
Press </, to select ANTENA.
PLAY
PREAJUSTE SINTONIZADOR
[ ANTENA ]
Ant / Cable:
Ajuste automático
Añadir / Borrar canales
OK
Escoger : Vv
Fin
: OK
Press M/m to move the cursor (B) to “Ajuste
automático,” then press OK (aceptación).
5
PLAY
1
2
3
4
5
6
7
8
9
Number
buttons
ENTER
(introducción)
0
CH (canal) +/–
Ajustar : Bb
Salir
: MENU
Ajuste auto
CH 2 0
MENU
All receivable channels are preset in numerical
sequence. When no more receivable channels
can be found, presetting stops and the picture
from the lowest numbered channel is displayed
on the TV screen.
OK
Ajustar : Bb
Salir
: MENU
Getting Started
Before you start…
• Turn on the VCR and the TV. When using
a cable box, turn it on.
• Set the “Salida video” to “3CH (canal3)”
or “4CH (canal4)” in the OPCIONES
AVANZADAS menu, whichever channel is
not used in your area. If both are used, set
the “Salida video” to either channel
(page 47). If your TV is connected to the
VCR using A/V connections, set the TV to
video input.
• Press TV/VIDEO to display the VIDEO
indicator in the VCR’s display window.
PLAY
• • • • • Por favor espere • • • • •
MENU
Press MENU.
13942296513
13942296513
1
TEL
TEL
M/m/</,
OK (aceptación)
MENU PRINCIPAL
Prog. / Verif.
Ajuste del reloj
Preajuste sintonizador
Opciones Avanzadas
Language / Idioma
Escoger : Vv
Ajustar : OK
2
PLAY
Press M/m to move the cursor (B) to “Preajuste
sintonizador,” then press OK (aceptación).
OK
Salir : MENU
PREAJUSTE SINTONIZADOR
[ CABLE ]
Ant / Cable:
Ajuste automático
Añadir / Borrar canales
Escoger : Vv
Fin
: OK
Ajustar : Bb
Salir
: MENU
Presetting channels
PLAY
Playing a tape
OK
4
1
2
3
4
5
6
7
8
9
0
• To preset a channel:
1 Press the number buttons to enter the
channel number, then press ENTER
(introducción).
2 Press ,, then press OK (aceptación) or
MENU.
Z EJECT
(expulsión)
?/1
Channel to be preset
AÑADIR / BORRAR CANALES
[
1]
Seleccione canal:
y Oprima
[ b ] para AÑADIR
[ B ] para BORRAR
PLAY
Fin
OK
: OK
Salir : MENU
1
2
3
4
5
6
7
8
9
TRINITRON TV
SYNCHRO PLAY
(reproducción
sincronizada de
TV Trinitron)
CLEAR
(cancelación)
DISPLAY
(indicación)
MENU
0
• CH
• To disable a channel:
Channel to be disabled
1 Press CH (canal) +/– to select the channel
number.
AÑADIR / BORRAR CANALES
[
5]
Seleccione canal:
REPLAY
(repetición)
2 Press <, then press OK (aceptación) or
MENU.
X PAUSE (pausa)
COMMERCIAL
SKIP (omisión de
anuncios)
H PLAY
(reproducción)
y Oprima
[ b ] para AÑADIR
[ B ] para BORRAR
PLAY
OK
Fin
: OK
Salir : MENU
MENU
M FF (avance
rápido)
x STOP (parada)
m REW
(rebobinado)
www
22
Presetting channels
.
x iao y u163. co m
1
Turn on your TV and set it to the video channel.
2
Insert a tape.
1-5
http://www.xiaoyu163.com
The VCR turns on and starts playing
automatically if you insert a tape with its
safety tab removed.
continued
Playing a tape
23
376315150 892498299
Basic Operations
Press M/m to move the cursor (B) to “Añadir/Borrar canales,” then press
OK (aceptación).
3
21
Basic Operations
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Presetting channels
QQ
QQ
continued
20
http://www.xiaoyu163.com
QQ 376315150 892498299
To use the time counter
Press CLEAR (cancelación) at the point on the tape that you want to find later. The
counter in the display window resets to “00:00” or “0:00.” To search for the counter
0:00:00 point automatically, see “To search for the counter 0:00:00 point” on page 44.
Press H PLAY (reproducción).
3
PLAY
OK
The display window shows the
playback time and playback direction.
When the tape reaches the end, it will
rewind automatically.
Hour
Minute
Additional tasks
To display the counter on the TV screen, press DISPLAY (indicación).
To
Press
Stop play
x STOP (parada)
Pause play
X PAUSE (pausa)
Resume play after pause
X PAUSE (pausa) or H PLAY (reproducción)
M FF (avance rápido) during stop
Rewind the tape
m REW (rebobinado) during stop
Eject the tape
Z EJECT (expulsión)
To play a recently watched scene
You can immediately rewind and playback the scene you want to watch again.
Turning on the VCR and TV, and starting playback
automatically (Trinitron TV Synchro Play)
During playback, press REPLAY (repetición). The VCR rewinds the tape about ten
seconds on the counter for each press of the button, and restarts playback.
Basic Operations
Fast-forward the tape
Notes
• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but the
picture quality cannot be guaranteed.
• While displaying a menu on the TV screen, you cannot use H PLAY (reproducción),
X PAUSE (pausa), M FF (avance rápido), m REW (rebobinado), or x STOP (parada)
buttons.
• The counter resets to “00:00” or “0:00” (in the display window) or “0:00:00” (on the TV
screen) whenever a tape is reinserted.
• The counter stops counting when it comes to a portion with no recording.
• When 10 hours have passed, the counter in the display window returns to “0:00” and the
count starts over again.
• When playback does not start even if you insert a tape with its safety tab removed, set “Autoreproducción” in the OPCIONES AVANZADAS menu correctly (page 46).
You can only use this function if your TV is made by Sony (Trinitron TV).
TEL
TEL
To skip playback
You can skip a portion of playback you do not want to watch (such as a commercial)
and restart playback.
13942296513
During playback, press COMMERCIAL SKIP (omisión de anuncios) up to four
times. The VCR skips the tape 30 seconds on the counter for each press of the
button, and restarts playback.
13942296513
How to connect to use this function
Connect the VCR and TV with the audio/video cable (see “Audio/video (A/V)
hookup” on pages 9 and 10). Be sure to connect the audio/video cable to the VIDEO
IN 1 (entrada de video 1) jacks on the TV if the TV has two inputs or more. The TV
must be placed where it will respond to the remote commander while you are
pointing it at the VCR.
Operation
Make sure that the TV’s power is in standby mode.
Press TRINITRON TV SYNCHRO PLAY (reproducción sincronizada de TV
Trinitron) and hold the remote commander in place for about two seconds.
The VCR and TV turn on, and the TV is set to the video channel. If there is a tape in
the VCR, playback starts automatically.
To turn off the power while rewinding (Rewind Shut Off)
Press ?/1 while the tape is rewinding. The power will turn off but the tape will keep
rewinding until it reaches the end.
24
Playing a tape
TV/VIDEO
1
2
3
4
5
6
7
8
9
0
COUNTER/
REMAIN
(contador/resto)
DISPLAY
(indicación)
ENTER
(introducción)
SP/EP
3
• CH
4
SP / EP
5
REC
Press CH (canal) +/– to select the channel or line input video source you
want to record.
Press SP/EP to select the tape speed, SP or EP.
EP (Extended Play) provides recording time three times as long as SP
(Standard Play). However, SP produces better picture and audio quality.
Press z REC (grabación) to start recording.
“REC (grabación)” appears in the display window.
CH (canal) +/–
INPUT SELECT
(selección de
entrada)
z REC
(grabación)
To stop recording
Press x STOP (parada).
To check the remaining tape length
Press DISPLAY (indicación). With the display on, press COUNTER/REMAIN
(contador/resto) to check the remaining time. Each time you press COUNTER/
REMAIN (contador/resto), the time counter and the remaining tape length appear
alternately. The white bar indicates the current location in relation to the entire tape
length. The remaining time also appears in the display window.
x STOP (parada)
26
www
x iao y u163. co m
0 : 0 0 : 3 0 SP
1
Turn on your TV and set it to the video channel.
2
Insert a tape with its safety tab in place.
Time counter
To record from a cable box, turn it on.
Recording TV programs
.
Rem 1 : 3 8 SP
Remaining tape length
To check the remaining tape length of a tape, set “Selc. de cinta” in the OPCIONES
AVANZADAS menu correctly (page 46).
continued
Recording TV programs
1-6
http://www.xiaoyu163.com
27
376315150 892498299
Recording TV programs
25
Basic Operations
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Playing a tape
QQ
QQ
Notes
• If the Trinitron TV Synchro Play function does not work properly:
– Wait a few moments, and press the button again.
– Replace both of the batteries with new ones, and press the button again.
Note that this function may not operate some Sony TVs because of the remote commander’s
signal limitations.
• Do not press TRINITRON TV SYNCHRO PLAY (reproducción sincronizada de TV
Trinitron) during playback. If you do so, the TV’s input source will momentarily switch to
the TV’s tuner.
http://www.xiaoyu163.com
QQ 376315150 892498299
To watch another TV program while recording
Recording TV programs using the DIAL
TIMER (temporizador dial) (not available on
1 Press TV/VIDEO to turn off the VIDEO indicator in the display window.
your TV is connected to the VCR using A/V connections, set the TV to the
2 IfTV’s
antenna input; if not, skip this step.
3 Select another channel on the TV.
SLV-LX500)
The Dial Timer function allows you to make
timer recordings of programs without turning
on your TV. Set the recording timer to record
up to eight programs that will be broadcast
within a month using the DIAL TIMER
(temporizador dial). The recording start time
and recording stop time can be set at one
minute intervals.
To save a recording
To prevent accidental erasure, break
off the safety tab as illustrated. To
record on the tape again, cover the tab
hole with adhesive tape.
Before you start...
• When using a cable box, turn it on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total recording time.
1
DIAL TIMER
x STOP
(parada)
DIAL TIMER X PAUSE
(temporizador (pausa)
dial)
Press DIAL TIMER (temporizador dial).
The current date appears in the display window.
If the date and time are not set, “1” will appear. See step 2 in the following
section “To set the clock” to set the date and time.
TEL
TEL
Notes
• The remaining tape length may not be indicated accurately for short tapes such as T-20 or T30, or tapes recorded in the LP mode.
• The display does not appear during still (pause) mode or slow-motion playback.
• It may take up to one minute for the VCR to calculate and display the remaining tape length
after you press DISPLAY (indicación).
Basic Operations
Safety tab
Tips
• To select a channel, you can use the number buttons on the remote commander. Enter the
channel number, then press ENTER (introducción).
• You can select a video source from the LINE IN 1 (entrada de línea 1) or LINE-2 IN (entrada
de línea 2) jacks using the INPUT SELECT (selección de entrada) button.
• The display appears on the TV screen indicating information about the tape, but the
information will not be recorded on the tape.
• If you do not want to watch TV while recording, you can turn off the TV. When using a cable
box, make sure to leave it on.
?/1 POWER CHANNEL
(alimentación)(canal) +/–
DIAL TIMER
Turn DIAL TIMER (temporizador dial) to set the recording date.
13942296513
13942296513
2
4
DIAL TIMER
Press DIAL TIMER (temporizador dial).
“AM” or “PM” and the time appear alternately in the display window.
DIAL TIMER
DIAL TIMER
8
DIAL TIMER
Press DIAL TIMER (temporizador dial).
The channel number appears in the display window.
Turn DIAL TIMER (temporizador dial) to set the channel number.
To record from a source connected to the LINE IN 1 (entrada de línea 1) or
LINE-2 IN (entrada de línea 2) jacks, turn DIAL TIMER (temporizador
dial) or press INPUT SELECT (selección de entrada) to display “L1” or
“L2.”
INPUT
SELECT
Turn DIAL TIMER (temporizador dial) to set the recording start time.
You can set the recording start time in 15 minute intervals or adjust the time
in one minute intervals by pressing the CHANNEL (canal) +/– buttons.
9
CHANNEL
5
7
29
DIAL TIMER
DIAL TIMER
Press DIAL TIMER (temporizador dial) to complete the setting.
“OK (aceptación)” appears in the display window for about five seconds.
The TIMER (temporizador) indicator appears in the display window and the
VCR stands by for recording. When using a cable box, leave it on.
Press DIAL TIMER (temporizador dial).
“AM” or “PM” and the time appear alternately in the display window.
To return to the previous step
To return to the previous step, press the CHANNEL (canal) + and – buttons on the
VCR at the same time during any of the Dial Timer settings.
To stop recording
To stop the VCR while recording, press x STOP (parada).
6
DIAL TIMER
Turn DIAL TIMER (temporizador dial) to set the recording stop time.
You can also do the following tasks while the VCR is recording:
You can set the recording stop time in 15 minute intervals or adjust the time
in one minute intervals by pressing the CHANNEL (canal) +/– buttons.
www
CHANNEL
30
To use the VCR after setting the timer
To use the VCR before a timer recording begins, just press ?/1. The TIMER
(temporizador) indicator disappears from the display window and the VCR switches
on. Remember to press ?/1 to reset the VCR to the timer recording standby mode
after using the VCR.
•
•
•
•
Reset the counter (page 25).
Display tape information on the TV screen (page 27).
Check the timer settings (page 40).
Watch another TV program (page 28).
x iao y u163. co m
To set the clock
.
down DIAL TIMER (temporizador dial) so that the DAY (día) indicator and
1 Hold
“1” appear in the display window. However, if the clock has already been set, the
current setting appears.
Recording TV programs using the DIAL TIMER (temporizador dial) (not available on SLV-LX500)
continued
Recording TV programs using the DIAL TIMER (temporizador dial) (not available on SLV-LX500)
1-7
http://www.xiaoyu163.com
31
376315150 892498299
3
Recording TV programs using the DIAL TIMER (temporizador dial) (not available on SLV-LX500)
Basic Operations
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Recording TV programs
QQ
QQ
continued
28
http://www.xiaoyu163.com
QQ 376315150 892498299
2 Turn DIAL TIMER (temporizador dial) to set the day.
DIAL TIMER (temporizador dial).
3 Press
The MONTH (mes) indicator and “1” appear in the display window.
Turn and press DIAL TIMER (temporizador dial) to set the month and then the
4 year.
Recording TV programs using the timer
You can preset up to eight programs together
with the DIAL TIMER (temporizador dial)*
at one time.
After you set the year, “AM” and “12:– –” appear alternately in the display
window.
Turn and press DIAL TIMER (temporizador dial) to set the hour and minute.
Before you start…
• Check that the VCR clock is set to the
correct time.
• Turn on the VCR and the TV and set it to
the video channel. When using a cable
box, turn it on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
5
you have finished setting the time, press DIAL TIMER (temporizador dial)
6 When
to start the clock.
*not available on SLV-LX500.
1
2
3
4
5
6
7
8
9
0
CH (canal) +/–
INPUT SELECT
(selección de
entrada)
TIMER
(temporizador)
MENU
TEL
TEL
Notes
• If eight programs have already been set using the manual timer setting, “FULL” appears in
the display window for about five seconds.
• The TIMER (temporizador) indicator flashes in the display window when you complete the
setting in step 9 on page 31 with no tape inserted.
• When the setting time is incorrect, “Err” appears in the display window in step 9. Set the
timer again from step 1.
• You cannot set the tape speed to “AUTO” using the DIAL TIMER (temporizador dial). To
select “AUTO,” set the “VEL” position in “Prog./Verif.”
Basic Operations
Tips
• To cancel a Dial Timer setting, press x STOP (parada) on the VCR while you are making the
setting.
• The program is recorded in the current tape speed. To change the tape speed, press SP/EP
before you complete the setting in step 9 (page 31).
• To check, change, or cancel the program setting, see “Checking/changing/canceling timer
settings” on page 40.
?/1
M/m/</,
OK (aceptación)
x STOP (parada)
About the Demonstration Mode
To activate the Demonstration Mode
Press X PAUSE (pausa) on the VCR while turning the DIAL TIMER (temporizador
dial). “DEMO” appears in the display window for a few seconds.
1
To cancel the Demonstration Mode
Turn the power off and unplug the AC power cord. Although the Demonstration
Mode is canceled, the timer settings entered while using the Demonstration Mode
will remain. Be sure to manually cancel the timer settings before you use the Dial
Timer or any other timer method after reconnecting the AC power cord (page 40).
TIMER
Press TIMER (temporizador).
CH COM.
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
Escoger : Bb
: OK
Fin
13942296513
13942296513
The DIAL TIMER (temporizador dial) function has a Demonstration Mode that
allows the user, such as a salesperson, to enter more than eight examples of timer
settings when demonstrating the use of the DIAL TIMER (temporizador dial). It
cancels the FULL notice which appears if eight programs have already been set. Do
not use the Demonstration Mode for making timer recordings. Doing so may cause
the settings to be inaccurate.
TER.
DIA VEL
– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-Ajustar : Vv
: MENU
Salir
To use the VCR after setting the timer
To use the VCR before a timer recording begins, just press ?/1. The TIMER
(temporizador) indicator disappears from the display window and the VCR switches
on. Remember to press ?/1 to reset the VCR to the timer recording standby mode
after using the VCR.
If necessary, press M/m to move the cursor (B) to the row that is to be set.
2
PLAY
OK
3
PLAY
OK
Set the channel number, start and stop time,
date, and tape speed:
1 Press , to flash each item in turn.
2 Press M/m to set each item.
INPUT
SELECT
• CH
To correct a setting, press < to return to
that setting and reset.
You can also do the following tasks while the VCR is recording:
CH COM.
3 5 8 : 0 0 PM
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
Escoger : Bb
: OK
Fin
TER.
DIA VEL
9 : 0 0 PM 3 0 / 9 SP
– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-Ajustar : Vv
: MENU
Salir
•
•
•
•
To record from a source connected to the LINE IN 1 (entrada de línea 1) or
LINE-2 IN (entrada de línea 2) jacks, press INPUT SELECT (selección de
entrada) or CH (canal) +/– to display “L1” or “L2” in the “CH (canal)”
position.
Tips
• To set the channel, you can also use the CH (canal) +/– or number buttons.
• To show the “Prog./Verif.,” you can use the MENU button. Press MENU, press M/m to
move the cursor (B) to “Prog./Verif.,” then press OK (aceptación).
• If the indicator appears, the timer settings overlap. To check, change or cancel the program
setting, see “Checking/changing/canceling timer settings” on page 40.
• If the
indicator appears, this means that the VCR is currently recording this program.
To use the Auto Tape Speed function, press m to display “AUTO” in the
“VEL” position. For details, see “To use the Auto Tape Speed function” on
page 35.
Press OK (aceptación) to confirm the setting.
PLAY
Reset the counter (page 25).
Display tape information on the TV screen (page 27).
Check the timer settings (page 40).
Watch another TV program (page 28).
To use the Auto Tape Speed function
When you are recording a program in the SP mode and the remaining tape becomes
shorter than the recording time, the tape speed is automatically changed to the EP
mode. Note that some noise will appear on the picture when the tape speed is
changed. If you want to keep the tape speed, select SP. To operate this function, set
“Selc. de cinta” in the OPCIONES AVANZADAS menu correctly (page 46).
To record the same program every day or the same day every week, press m
while the date is flashing. For details, see “Daily/weekly recording” below.
4
33
To enter another setting, press M/m to select the next row and repeat step 4.
OK
5
6
TIMER
Press TIMER (temporizador) to exit the menu.
Press ?/1 to turn off the VCR.
The TIMER (temporizador) indicator appears in the display window and the
VCR stands by for recording. When using a cable box, leave it on.
x iao y u163. co m
To stop recording
To stop the VCR while recording, press x STOP (parada).
www
Daily/weekly recording
In step 4 above, press m to select the recording pattern. Each time you press m, the
indication changes as shown below. Press M to change the indication in reverse
order.
.
LU–VI t CADA DO t CADA LU t ..... t CADA–SA t 1 month later t (dates
count down) t the current date
34
Recording TV programs using the timer
Recording TV programs using the timer
1-8
http://www.xiaoyu163.com
35
376315150 892498299
QQ 3763 1515 0 89 2498 299
Recording TV programs using the timer
Basic Operations
376315150 892498299
TEL 13942296513
Recording TV programs using the DIAL TIMER (temporizador dial) (not available on SLV-LX500)
QQ
QQ
continued
32
http://www.xiaoyu163.com
QQ 376315150 892498299
Additional Operations
Locking the VCR (Child Lock)
After you have set the timer, you can lock all
of the buttons on the VCR so that the settings
are not canceled by mistake.
Playing/searching at various speeds
?/1 POWER (alimentación)
x2
y SLOW (cámara
lenta)
x STOP (parada)
To lock the VCR
When the VCR is turned on, hold down ?/1 POWER (alimentación) on the VCR
until “LOC” appears in the display window. The VCR turns off and the TIMER
(temporizador) indicator remains lit if there is a timer setting. The VCR will not
work except for timer recordings.
H PLAY
(reproducción)
M FF (avance
rápido)
TRACKING (seguimiento) +/–
m REW
(rebobinado)
To stop timer recording while the VCR is locked, press x STOP (parada). The
recording stops and the VCR is unlocked.
Operation
View the picture during fastforward or rewind
During fast-forward, hold down M FF (avance rápido). During
rewind, hold down m REW (rebobinado).
Play at high speed
• During playback, briefly press M FF (avance rápido) or m REW
(rebobinado). The tape continues to play at high speed.
• During playback, hold down M FF (avance rápido) or m REW
(rebobinado). When you release the button, normal playback
resumes.
Play at twice the normal speed
During playback, press ×2.
Play in slow motion
During playback or pause, press y SLOW (cámara lenta).
Play frame by frame
During pause, press M FF (avance rápido) on the remote commander.
13942296513
13942296513
Playback options
To resume normal playback
Press H PLAY (reproducción).
Playing/searching at various speeds
Setting the recording duration time
After you have started recording, you can
have the VCR stop recording automatically
after a specified duration.
Notes
• The sound is muted during these operations.
• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but the
picture quality cannot be guaranteed.
• The picture may show noise when playing at high speed in reverse.
z REC
(grabación)
recording, press z REC (grabación).
1 While
The TIMER (temporizador) indicator appears in the display window.
z REC (grabación) repeatedly to set the duration time.
2 Press
Each press advances the time in increments of 30 minutes.
0:30
1:00
3:30
4:00
Normal recording
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.
To extend the duration
Press z REC (grabación) repeatedly to set a new duration time.
www
38
To cancel the duration
Press z REC (grabación) repeatedly until the TIMER (temporizador) indicator
disappears and the VCR returns to normal recording mode.
x iao y u163. co m
To stop while recording
Press x STOP (parada).
.
Note
• You cannot display the current tape time in the display window when setting the recording
duration time.
Playing/searching at various speeds
1-9
http://www.xiaoyu163.com
Setting the recording duration time
39
376315150 892498299
Tip
• Adjust the picture using the TRACKING (seguimiento) +/– buttons if:
– Streaks appear while playing in slow motion.
– The picture shakes during pause.
• The VCR turns on and starts playback automatically by pressing H PLAY (reproducción)
on the VCR with the VCR power turned off.
37
Additional Operations
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Locking the VCR (Child Lock)
QQ
QQ
continued
36
TEL
TEL
Note
• The VCR will be unlocked when:
– You stop timer recording by pressing x STOP (parada).
– You insert a tape.
– The AC power cord is disconnected or power supply stops.
Additional Operations
To unlock the VCR
Hold down ?/1 POWER (alimentación) on the VCR until “LOC” disappears from
the display window. The VCR is unlocked and turns on.
http://www.xiaoyu163.com
QQ 376315150 892498299
M/m to move the cursor (B) to the setting
3 Press
you want to change or cancel.
Checking/changing/canceling timer
settings
Before you start…
• Turn on the TV and set it to the video
channel.
• To cancel the setting, press CLEAR
(cancelación).
Press OK (aceptación) to confirm the setting.
CLEAR
(cancelación)
2
3
4
5
6
8
9
7
TER.
DIA VEL
9 : 0 0 PM 3 0 / 9 SP
11 : 3 0 AM 0 2 / 10 EP
10 : 0 0 PM 3 0 / 9 AUTO
– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-– : ––
–––
-Ajustar : Vv
: MENU
Salir
4
TIMER (temporizador) to exit the menu.
5 Press
If any timer settings remain, turn off the VCR to return to recording standby.
?/1
1
CH COM.
3 5 8 : 0 0 PM
2 0 10 : 0 0 AM
6 0 8 : 3 0 PM
–– – : ––
–– – : ––
–– – : ––
–– – : ––
–– – : ––
Escoger : Bb
: OK
Fin
• To change the setting, press </, to flash the
item you want to change, and press M/m to
change it.
When the timer settings overlap
The program that starts first has priority and the second program starts recording only
after the first program has finished. If the programs start at the same time, the
program listed first in the menu has priority.
Program 1
0
Will be cut off
TIMER
(temporizador)
Tip
• To show the “Prog./Verif.,” you can use the MENU button. Press MENU, press M/m to
move the cursor (B) to “Prog./Verif.,” then press OK (aceptación).
M/m/</,
OK (aceptación)
13942296513
13942296513
1 Press ?/1 to turn on the VCR.
TIMER (temporizador).
2 Press
• If you want to change a setting, go on to the next step.
• If you do not need to change the settings, press MENU, then turn off the VCR
to return to recording standby.
Checking/changing/canceling timer settings
Recording stereo and bilingual programs
41
Searching using various functions
(not available on SLV-LX500)
The VCR automatically marks the tape with
an index signal at the point where each
recording begins.
You can easily find a specific point using
various search functions.
Recording stereo programs
When you receive a program broadcast in stereo, press AUDIO MONITOR (monitor
de audio) to display ESTÉREO on the TV screen. You can also select IZQUIERDA,
DERECHA, or MONOFÓNICO. If there is noise in the stereo program, select
MONOFÓNICO. The sound will be recorded in monaural (on both hi-fi and normal
audio tracks) but with less noise.
SEARCH
(búsqueda)
Recording bilingual programs
M/m/</,
H PLAY
(reproducción)
Press AUDIO MONITOR (monitor de audio) to display “SAP” on the TV screen.
When a SAP (Second Audio Program) is received, “SAP” appears on the TV screen.
When PRINCIPAL is selected, the VCR records only the main sound.
Selecting the sound during playback
To listen to
On-screen display
Display window
Stereo
ESTÉREO
Hi-Fi
Left channel
IZQUIERDA
Hi-Fi
Right channel
DERECHA
Hi-Fi
Monaural sound on the
normal audio track
MONOFÓNICO
No indicator
To search using the index function (Scan and Play)
The VCR automatically marks the tape with an index signal at the point where each
recording begins. Use these signals as references to find a specific recording.
1 Insert an indexed tape into the VCR.
2 Press SEARCH (búsqueda).
Búsqueda y reproducción:
Presione [ B ] o [ b ]
Vaya a [ 0 : 0 0 : 0 0 ] :
Presione [ V ]
Búsqueda del fin:
Presione [ v ]
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the
main track along with the picture. Monaural sound is recorded onto the normal audio
track along the edge of the tape.
Normal audio track
Hi-fi audio track
(main track)
www
0 : 0 1 : 3 0 SP
, to scan ahead, or < to scan backwards.
3 Press
The VCR searches and then plays back for about
Monaural sound
five seconds.
Búsqueda y reproducción
x iao y u163. co m
0 : 0 1 : 3 0 SP
Stereo sound
(left/right channels)
H PLAY (reproducción) to view that program.
4 Press
If you do not press H PLAY (reproducción), the VCR automatically searches
for the next index mark, or until it reaches the end of the tape.
Notes
• To play a tape in stereo, you must use the A/V connections.
• When you play a tape recorded in monaural, the sound is heard in monaural regardless of the
AUDIO MONITOR (monitor de audio) setting.
42
Additional Operations
During playback, press AUDIO MONITOR (monitor de audio) to select the sound
you want.
.
Recording stereo and bilingual programs (not available on SLV-LX500)
continued
Searching using various functions
1-10
http://www.xiaoyu163.com
43
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Checking/changing/canceling timer settings
QQ
QQ
40
TEL
TEL
Additional Operations
Program 2
http://www.xiaoyu163.com
QQ 376315150 892498299
To search for the counter 0:00:00 point
Adjusting the picture (tracking)
To mark a point on the tape that you want to find later, reset the tape counter to
“0:00:00.”
The VCR automatically fast-forwards or rewinds to the 0:00:00 point on the tape
counter.
Although the VCR automatically adjusts the tracking
when playing a tape, distortion may occur if the
recording is in poor condition. In this case, manually
adjust the tracking.
1
M.
2 Press
The VCR starts searching and automatically
Press SEARCH (búsqueda).
stops at the 0:00:00 point.
Press TRACKING (seguimiento) +/– on the VCR to
display the tracking meter. The distortion should
disappear as you press one of the two tracking
buttons. To resume automatic tracking adjustment,
eject the tape and reinsert it.
Vaya a [ 0 : 0 0 : 0 0 ]
0 : 0 1 : 3 0 SP
SEGUIMIENTO
Tracking meter
Note
• The auto tracking adjustment cannot be guaranteed to work with tapes recorded in the LP
mode on other VCRs.
To search for a blank portion of the tape
The VCR automatically searches for the beginning of a blank portion. You can easily
find a point you can start recording from.
TEL
stops at the beginning of a blank space. If no
blank space is found, the VCR reaches the end
and the tape will be ejected.
Búsqueda del fin
0 : 0 1 : 3 0 SP
Searching using various functions
Adjusting the picture (tracking)
45
OPCIONES AVANZADAS
Selc. de cinta:
Auto-reproducción:
Auto-repetición:
Auto-apagado:
Ahorro energía:
Salida video:
Escoger : Vv
Fin
: OK
[ T1 2 0 ]
[ SI ]
[ NO ]
[ NO ]
[ NO ]
[ 3CH ]
TV
Ajustar : Bb
Salir
: MENU
3 Press M/m to move the cursor (B) to the option to change.
4 Press </, to change the setting, then press OK (aceptación).
5 Press MENU to exit the menu.
Menu option
Set this option to
• T-120 when using a T-120 or shorter length tape.
• T-160 when using a T-160 length tape.
• T-180 when using a T-180 or longer length tape.
For details, see page 27.
Auto-reproducción
• SI to start playback automatically, when you insert a tape with
its safety tab removed.
• NO to turn off Auto play. You need to press H PLAY
(reproducción) to start playback, even if you insert a tape with
its safety tab removed.
Auto-repetición
• SI to play back a tape repeatedly. The VCR rewinds a tape to
the beginning and restarts playback automatically.
• NO to turn off Auto repeat.
Auto-apagado
• 1h to turn off the VCR automatically one hour after the last
operation.
• 2h to turn off the VCR automatically two hours after the last
operation.
• NO to set no specific time to turn off.
www
46
.
Changing menu options
2
3
4
5
6
7
8
9
CHANNEL (canal) +/–
?/1 POWER
(alimentación)
Selc. de cinta
Salida video
1
0
Menu choices
Initial settings are indicated in bold print.
Ahorro energía
TV/VIDEO
the “Salida video” to “3CH (canal3)” or “4CH (canal4)” in the OPCIONES
1 Set
AVANZADAS menu, whichever channel is not used in your area. If both are
used, set the “Salida video” to either channel.
2 Press ?/1 POWER (alimentación) to turn on the VCR.
3 Press TV/VIDEO to turn on the VIDEO indicator in the VCR’s display window.
CHANNEL (canal) +/– to display a channel number in the display window.
4 Press
Select an active channel number in your area.
on your TV and set it to the channel you selected in step 1 (channel 3 or 4).
5 Turn
The channel you selected in step 4 appears on the TV screen. If the channels
change when you press CHANNEL (canal) +/–, you have made the correct
setting.
Whenever you use the VCR, set the TV to the channel selected in step 1.
x iao y u163. co m
• SI to turn off the indicators in the display window during
standby mode to reduce the VCR’s power consumption to a
minimum.
• NO to turn on the indicators in the display window while the
VCR is standing by.
• 3CH (canal3) when using channel 3 to receive the VCR signal.
• 4CH (canal4) when using channel 4 to receive the VCR signal.
For details, see page 47
1-11
http://www.xiaoyu163.com
Changing menu options
47
376315150 892498299
1
M/m to move the cursor (B) to “Opciones
2 Press
Avanzadas,” then press OK (aceptación).
When connecting the VCR to the TV using
only the antenna cable, you must set the
“Salida video” in the OPCIONES
AVANZADAS menu so that the TV can
receive the correct signal from the VCR.
Press MENU.
Additional Operations
376315150 892498299
Setting the RF Output channel
Changing menu options
QQ
QQ
QQ 3763 1515 0 89 2498 299
TEL 13942296513
44
13942296513
13942296513
Note
• Once in recording mode, if the VCR is put in pause and then released to start the recording,
no index mark will be inserted. An index mark will be inserted if the channel is changed
while VCR is put in pause.
TEL
Additional Operations
1 Press SEARCH (búsqueda).
m.
2 Press
The VCR starts searching and automatically
http://www.xiaoyu163.com
QQ 376315150 892498299
Notes
• Make sure you connect the plugs to jacks of the same color.
• If the other VCR is a monaural type and connected to this VCR’s LINE-2 IN (entrada de línea
2) jacks, connect the audio plug to the AUDIO L (audio izquierda) (white) jack. The sound is
recorded on both right and left channels. If you connect to the AUDIO R (audio derecha)
(red) jack, the sound is recorded only on the right channel (SLV-LX700S and SLV-LX600S
only).
• If you connected this VCR to both the LINE IN (entrada de línea) and LINE OUT (salida de
línea) jacks of the other VCR, select the input correctly to prevent a humming noise.
• You can use the LINE IN 1 (entrada de línea 1) jacks for editing.
• If the other VCR is a monaural type and connected to this VCR’s LINE IN 1 (entrada de línea
1) jacks, the sound is recorded only on the channel whose jack is connected to the audio plug.
To record on both right and left channels, connect the audio plugs to the AUDIO R/L (audio
derecha/izquierda) jacks using an audio/video cable (not supplied) (SLV-LX700S and SLVLX600S only).
Editing with another VCR
How to connect to record on this VCR
For SLV-LX700S and SLV-LX600S
TV
This VCR (Recorder)
LINE-2 IN (entrada de línea 2)
Operation (when recording on this VCR)
Before you start editing
• Turn on the VCR and the TV and set
it to the video channel.
Other VCR (Player)
X PAUSE (pausa)
• Press SP/EP to select the tape speed,
SP or EP.
Audio/video cable (not supplied)
: Signal flow
TV
13942296513
13942296513
LINE-2 IN (entrada de línea 2)
To stop editing
Press the x STOP (parada) buttons on both VCRs.
Tip
• To cut out unwanted scenes while editing, press X PAUSE (pausa) on this VCR when an
unwanted scene begins. When it ends, press X PAUSE (pausa) again to resume recording.
Other VCR (Player)
LINE OUT
(salida de línea)
Audio/video cable (not supplied)
: Signal flow
Editing with another VCR
Antenna information
Troubleshooting
Attaching the external antenna connector
When using a 300-ohm twin lead cable for a
VHF/UHF antenna, use an antenna connector
(not supplied) to connect the antenna to the
VCR.
If you have any questions or problems not covered below, please consult your nearest Sony
dealer.
300-ohm twin
lead cable
Power
Antenna
connector (not
supplied)
Clock
1 Loosen the screws on the antenna connector.
2 Wind the twin leads around the screws on the antenna connector.
3 Retighten the screws.
Attaching a UHF/VHF band mixer
UHF/VHF
Band
separator/
mixer (not
supplied)
50
Antenna information
Recording
1 Loosen the screws on the mixer.
2 Wind the twin leads around the screws on the mixer.
3 Retighten the screws.
4 Connect the 75-ohm coaxial cable to the mixer.
.
• Connect the AC power cord securely.
• Make sure the VCR is not locked. To unlock, hold down
?/1 POWER (alimentación) on the VCR until “LOC”
disappears.
The power is turned on but the VCR
does not operate.
• Moisture condensation has occurred. Turn the power off,
unplug the AC power cord and leave the VCR to dry for
over three hours.
The clock has stopped and “– –:– –”
appears in the display window.
• The clock stops if the VCR is disconnected from the wall
outlet for more than one minute. Reset the clock (and
timer).
The playback picture does not appear
on the TV screen.
• Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
The picture is not clear.
• Adjust the tracking with the TRACKING
(seguimiento) +/– buttons.
• The video heads are dirty (see the last page of
“Troubleshooting”). Clean the video heads using a
Sony’s video head cleaning cassette. If a Sony cleaning
cassette is not available in your area, have the heads
cleaned at your nearest Sony dealer (a standard service
fee will be charged). Do not use a commercially available
liquid type cleaning cassette, as it may damage the video
heads.
• The video heads may have to be replaced. Consult your
local Sony dealer for more information.
300-ohm twin
lead cable
75-ohm coaxial
cable
www
Remedy
The ?/1 switch does not function.
Playback
When using both a 75-ohm coaxial cable and
a 300-ohm twin lead cable for a VHF/UHF
antenna, use a UHF/VHF band separator/
mixer (not supplied) to connect the antenna
to the VCR.
Symptom
The picture rolls vertically during
picture search.
• Adjust the vertical hold control on the TV or monitor.
The picture has no sound.
• The tape is defective.
• If you made A/V connections, check the audio cable
connection.
A TV program does not appear on
the TV screen.
• Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
• Select the correct source with the INPUT SELECT
(selección de entrada) or CH (canal) +/– buttons. Select a
channel number when recording TV programs; select
“L1” or “L2” when recording from other equipment.
x iao y u163. co m
TV reception is poor.
• Adjust the TV antenna.
The tape starts playing as soon as it is
inserted.
• The safety tab has been removed. To record on this tape,
cover the tab hole.
The tape is ejected when you press
z REC (grabación).
• Check that the safety tab has not been removed.
Nothing happens when you press
z REC (grabación).
• Make sure the tape is not at its end.
1-12
http://www.xiaoyu163.com
continued
Troubleshooting
51
376315150 892498299
Additional Information
49
Additional Information
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
Editing with another VCR
QQ
QQ
48
TEL
TEL
a source tape with its safety tab removed into the other (playback) VCR.
1 Insert
Search for the point to start playback and set it to playback pause.
a tape into this (recording) VCR. Search for the point to start recording
2 Insert
and press X PAUSE (pausa).
Press z REC (grabación) on this VCR to set it to recording pause.
3
start editing, press the X PAUSE (pausa) buttons on both VCRs at the same
4 To
time.
For SLV-LX500
This VCR (Recorder)
z REC (grabación)
Additional Operations
• Press INPUT SELECT (selección de
entrada) or CHANNEL (canal) +/– to
display “L1” or “L2” in the display
window.
LINE OUT
(salida de línea)
http://www.xiaoyu163.com
QQ 376315150 892498299
Symptom
Remedy
The timer does not operate.
•
•
•
•
•
•
•
•
Timer recording
Others
Index to parts and controls
Check that the clock is set.
Make sure a tape has been inserted.
Check that the safety tab has not been removed.
Make sure the tape is not at its end.
Make sure a program has been set for timer recording.
Make sure your timer settings are past the current time.
Check that the cable box is turned on.
The clock stops if the VCR is disconnected from the wall
outlet for more than one minute. Reset the clock and
timer.
• Turn the power off and unplug the AC power cord.
• Check that a tape is not already in the tape compartment.
The remote commander does not
function.
• Make sure you are pointing the remote commander at the
remote sensor on the VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
• Make sure the •TV / VIDEO switch is set correctly.
The tracking meter does not appear
on the screen.
• The recording condition of the tape is very poor and
tracking cannot be adjusted.
You cannot control other TVs.
• Set your TV’s code number. The code number may
change when you replace the batteries of the remote
commander.
The VCR needs to be cleaned.
• Clean the cabinet, panel and controls with a dry, soft
cloth, or a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of solvent, such
as alcohol or benzine.
Front panel
A ?/1 POWER (alimentación) switch (34)
Display window is lit when the power is
on and dims (or goes off) when the power
is in standby mode.
B A EJECT (explusión) button (24)
C Remote sensor (5)
D Tape compartment
E m REW (rebobinado) button (24) (37)
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
• Unclear picture
F H PLAY (reproducción) button (24)
G M FF (avance rápido) button (24) (37)
H z REC (grabación) (record) button (27)
(39) (49)
initial
contamination
L CHANNEL (canal)/TRACKING
(seguimiento) +/– buttons*2 (27) (45)
M LINE-2 IN VIDEO/AUDIO L/R (entrada
de línea 2 de video/audio i/d jacks
(LINE-2 IN VIDEO/AUDIO (entrada de
línea 2 de video/audio) jacks for SLVLX500) (48)
*1 not available on SLV-LX500
*2 The CHANNEL (canal) + and H PLAY
(reproducción)/x STOP (parada) buttons have a
tactile dot.
terminal
54
Troubleshooting
SLV-LX700S/SLV-LX600S
A SP/EP (Reproducción estándar/
Reproducción extendida) indicator (27)
B TIMER (temporizador) indicator (34)
C Tape indicator (27)
D START (inicio) indicator (29)
G MONTH (mes) indicator (31)
I YEAR (año) indicator (32)
J Hi-Fi (hi-fi) indicator (42)
E STOP (parada) indicator (30)
K Time counter/clock/line/channel
indicator (25) (27) (49)
F DATE (fecha) indicator (32)
L VIDEO (video) indicator (28) (47)
www
.
SLV-LX500
H DAY (día) indicator (32)
A AC power cord (8) (12) (14)
B LINE OUT AUDIO R/L/VIDEO (salida
de línea de audio d/i/video) jacks (9)
E RF OUT (TO TV) (salida de
radiofrecuencia a televisor) connector
(11) (13) (15)
C LINE IN 1 AUDIO R/L/VIDEO (entrada
de línea 1 de audio d/i/video) jacks (49)
F IN AUDIO/VIDEO (entrada de audio/
video) (LINE IN 1 (entrada de línea 1))
jacks (49)
D RF IN (FROM ANT.) (entrada de
radiofrecuencia desde antena) connector
(11) (13) (15)
G OUT AUDIO/VIDEO (salida de audio/
video) (LINE OUT (salida de línea))
jacks (9)
x iao y u163. co m
continued
Index to parts and controls
55
56
Index to parts and controls
1-13
http://www.xiaoyu163.com
376315150 892498299
Rear panel
Additional Information
376315150 892498299
Display window
Index to parts and controls
QQ
QQ
QQ 3763 1515 0 89 2498 299
TEL 13942296513
52
K DIAL TIMER (tempolizador dial)*1 (29)
13942296513
13942296513
• No picture (or
black & white
screen appears)
I x STOP (parada) button (24) (49)
J X PAUSE (pausa) button (24) (49)
TEL
TEL
A tape cannot be inserted.
Refer to the pages indicated in parentheses ( ) for details.
http://www.xiaoyu163.com
QQ 376315150 892498299
Remote commander
A •TV / VIDEO (televisor/video) switch (5)
M ?/1 (alimentación) switch (6) (34)
B Z EJECT (expulsión) button (24)
N TV/VIDEO (televisor/video) button (6)
(28)
C TRINITRON TV SYNCHRO PLAY
(reproducción sincronizada de TV
Trinitron) button (25)
O AUDIO MONITOR (monitor de audio)
button*1, 2 (42)
D COUNTER/REMAIN (contador/resto)
button (27)
P CLEAR (cancelación) button (25) (41)
Q Number buttons*1 (28)
E DISPLAY (indicación) button (27)
1
2
3
4
5
6
7
8
F SP/EP (Reproducción estándar/
Reproducción extendida) button (27)
G INPUT SELECT (selección de entrada)
button (28) (49)
9
0
R ENTER (introducción) button (28)
1
2
3
4
5
6
S CH (canal) +/– buttons*1 (6) (27)
7
8
9
T VOL (volumen) +/– buttons (6)
U SEARCH (búsqueda) button (43)
0
H z REC (grabación) button (27) (39)
V REPLAY (repetición) button (24)
I TIMER (temporizador) button (33)
W ×2 button (37)
J y SLOW (cámara lenta) button (37)
X COMMERCIAL SKIP (omisión de
anuncios) button (24)
K MENU (menú) button (18) (33) (40) (46)
TEL
13942296513
13942296513
* The H PLAY (reproducción) button has a
tactile dot.
*1 The AUDIO MONITOR (monitor de audio),
number 5 and CH (canal) + buttons have a
tactile dot.
*2 not available on SLV-LX500
Additional Information
TEL
L X PAUSE (pausa)/M button (18) (24)
x STOP (parada)/m button (18) (24)
m REW (rebobinado)/ < button (24)
(37)
M FF (avance rápido)/ , button (24)
(37)
H PLAY (reproducción)/OK
(aceptación) button* (18) (24)
QQ 3763 1515 0 89 2498 299
58
Quick reference to using the VCR
Index
A
M
T
Adjusting
picture 45
tracking 45
Advanced option 46
Antenna hookup 11
Audio track 42
Audio/video (A/V) hookup 9
Auto Tape Speed 35
Monaural 42
Monitoring audio during
playback 42
C
Picture adjustment 45
Playback 23
at various speeds 37
frame by frame 37
selecting the sound 42
skip 24
slow motion 37
Presetting channels 19
Timer setting 33
canceling 40
changing 40
checking 40
daily/weekly recording 34
Tracking adjustment. see
Adjusting
Trinitron TV Synchro Play 25
Tuner presetting 19
Cable hookup 8
Child Lock 36
Cleaning the video heads 51
Clock setting 16
Commercial Skip 24
Connecting
Cable TV 15
external antenna connector
50
UHF/VHF band mixer 50
Counter 25
D
Demonstration Mode 32
Dial Timer 29
Disabling channels 21
Dubbing. see Editing
E
Editing 48
EP mode 27
H
Hi-fi audio track 42
L
N
Normal audio track 42
P
Hookup 1
Hookup 2
Hookup 3
To play a tape
To play a tape
To play a tape
1 Set the TV to channel 3 or 4
(or to video input, if you
made A/V connections).
2 Insert a tape and press
H PLAY (reproducción). If
there is no picture on your
TV, press the VCR’s TV/
VIDEO button until the
VIDEO indicator appears in
the display window.
1 If you made A/V
connections, set the TV to
video input. If you did not
use A/V hookup:
• Turn on the cable box.
• Set the cable box to channel
3 or 4.
• Set the TV to the output
channel of the cable box
(usually 2, 3, or 4).
2 Insert a tape and press
H PLAY (reproducción).
1 Set the TV to channel 3 or 4
(or to video input, if you
made A/V connections).
2 Insert a tape and press
H PLAY (reproducción).
To record a program
1 Press TIMER
(temporizador).
2 Set the channel, time, date,
and tape speed.
3 Press TIMER
(temporizador).
4 Insert a tape.
5 Press ?/1 to turn off the
VCR.
R
Recording 26
bilingual programs 42
SAP broadcasts 42
saving 28
stereo broadcasts 42
timer setting 33
using Dial Timer 29
while watching another
program 28
RF channel 47
To watch TV
1 Turn off the VCR, or press
the VCR’s TV/VIDEO
button until the VIDEO
indicator in the display
window turns off.
2 Set the TV to the channel you
want to watch.
S
To record a program
1 Press TIMER
(temporizador).
2 Set the channel, time, date,
and tape speed.
3 Press TIMER
(temporizador).
4 Insert a tape.
5 Press ?/1 to turn off the
VCR.
To watch TV
1 Turn off your VCR, or press
the VCR’s TV/VIDEO
button until the VIDEO
indicator in the display
window turns off.
2 Select the channel with your
cable box (if you have one)
or with your TV.
To record a program
1 Turn on the cable box.
2 Set the cable box to the
channel you want to record.
3 Press TIMER
(temporizador).
4 Set the channel, time, date,
and tape speed.
5 Press TIMER
(temporizador).
6 Insert a tape.
7 Press ?/1 to turn off the
VCR.
Leave the cable box on.
To watch TV
1 Turn off your VCR, or press
the VCR’s TV/ VIDEO
button until the VIDEO
indicator in the display
window turns off.
2 Turn on your cable box.
3 Set the TV to the cable box
output channel (usually 2, 3,
or 4).
4 Set the cable box to the
channel you want to watch.
Safety tab 28
SAP (Second Audio Program)
42
Searching
at various speeds 37
for a blank portion 44
for the counter 0 point 44
Scan and Play 43
SP mode 27
Stereo 42
www
Language selecting 18
Locking the VCR 36
LP mode 28
Index to parts and controls
.
x iao y u163. co m
Index
59
Sony Corporation
Printed in China
1-14E
http://www.xiaoyu163.com
AC68-01957A
376315150 892498299
376315150 892498299
TEL 13942296513
57
QQ
QQ
continued
Index to parts and controls
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 376315150 892498299
2. DISASSEMBLY
2-1 CABINET TOP
Cabinet top
TEL
TEL
13942296513
13942296513
1 Two screws
2 Lift up the cabinet top in the direction of arrow by releasing the hook.
1 Release four hooks
www
ASS'Y-PANEL FRONT
.
2 Release three hooks
– BOTTOM VIEW –
x iao y u163. co m
– TOP VIEW –
Fig. 2-2 Ass’y-Panel Front
2-1
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
TE2-2
L ASS’Y-PANEL
13942296513
FRONT
QQ
QQ
Fig. 2-1 Cabinet Top
http://www.xiaoyu163.com
QQ 376315150 892498299
2-3 ASS’Y JACK-PCB
Disconnect the CN701 from the ass'y PCB-main and then lift the ass'y PCB-jack up.
CN702
TEL
TEL
13942296513
13942296513
CN701
.
x iao y u163. co m
2-2
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
QQ 3763 1515 0 89 2498 299
Fig. 2-3 Ass’y Jack-PCB
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
QQ 376315150 892498299
2-4 ASS’Y JACK-MAIN, DECK
3 Four screws
4 Flat cable
5 Flat cable
9 Ass'y-deck
TEL
TEL
13942296513
13942296513
0 Ass'y main-PCB
7 Release hook
2 Bracket-frame
8 Release hook
www
.
x iao y u163. co m
Fig. 2-4 Ass’y Main-PCB, Deck
2-3
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 Two screws
QQ
QQ
QQ 3763 1515 0 89 2498 299
TEL 13942296513
6 Flat cable
http://www.xiaoyu163.com
QQ 376315150 892498299
MEMO
TEL
TEL
13942296513
13942296513
.
x iao y u163. co m
2-4E
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
QQ 3763 1515 0 89 2498 299
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
3. P.C.BOARDS
3-1 Main PCB - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-3
3-2 Function PCB - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-7
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
3-1
.
c o
8 9 2 4 9 8 2 9 9
m
3-2
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
3-1 MAIN PCB
COMPONENT SIDE
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
3-3
.
m
c o
3-4
http://www.xiaoyu163.com
8 9 2 4 9 8 2 9 9
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
CONDUCTOR SIDE
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
3-5
.
c o
8 9 2 4 9 8 2 9 9
m
3-6
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
3-2 FUNCTION PCB
COMPONENT SIDE
CONDUCTOR SIDE
8 9 2 4 9 8 2 9 9
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
3-7
.
c o
3-8E
http://www.xiaoyu163.com
8 9 2 4 9 8 2 9 9
m
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4. SCHEMATIC DIAGRAMS
4-1 S.M.P.S./Power (MX) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4-5
4-2 S.M.P.S./Power (CS) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4-7
4-3 Logic/Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4-9
4-4 Audio/Video - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4-11
4-5 Hi-Fi/MTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4-13
4-6 TM-Block/Input-Output- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4-15
13942296513
13942296513
4-3
TEL
TEL
♦ Block Identification of Main PCB - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 3 9 4 2 2 9 6 5 1 3
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-1
.
c o
8 9 2 4 9 8 2 9 9
m
4-2
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL
QQ
QQ
• Abbreviation
CS: Chile model, Peru model
MX: Mexican model
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
♦ BLOCK IDENTIFICATION OF MAIN PCB
TEL
TEL
13942296513
13942296513
QQ
3 7 6 3 1 5 1 5 0
Component Side
www
.
8 9 2 4 9 8 2 9 9
Conductor Side
x ia o y u 1 6 3
4-3
.
m
c o
4-4
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-1 S.M.P.S./POWER (MX)
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-5
.
c o
8 9 2 4 9 8 2 9 9
m
4-6
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-2 S.M.P.S./POWER (CS)
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-7
.
m
c o
4-8
http://www.xiaoyu163.com
8 9 2 4 9 8 2 9 9
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-3 LOGIC/DISPLAY
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-9
.
c o
8 9 2 4 9 8 2 9 9
m
4-10
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-4 AUDIO/VIDEO
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-11
.
m
c o
4-12
http://www.xiaoyu163.com
8 9 2 4 9 8 2 9 9
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-5 Hi-Fi/MTS
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-13
.
c o
8 9 2 4 9 8 2 9 9
m
4-14
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-6 TM-BLOCK/INPUT-OUTPUT
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
4-15
.
c o
m
4-16E
http://www.xiaoyu163.com
8 9 2 4 9 8 2 9 9
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 376315150 892498299
5. ALIGNMENT AND ADJUSTMENT
5-1 REFERENCE
1) X-Point (Tracking center) adjustment and “Head switching adjustment” can be adjusted with remote control.
2) When replacing the Micom (IC601) and NVRAM (IC603 ; EEPROM) be sure to adjust the “Head switching adjustment”.
3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”.
4) How to adjustment.
- Monmently short-circuit the test point on Main PCB with pincers to set the adjustment mode.
- If the corresponding adjustment button is pressed, the adjustment is performed automatically.
- If the adjustment is completed, be sure to turn the power off.
TEL
TEL
5-1-1 Location of adjustment button of remote control
13942296513
13942296513
Head Switching Adjustment
NVRAM Option Setting
www
.
x iao y u163. co m
Fig. 5-1
5-1
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
X-Point (Tracking Center)
Adjustment
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
QQ 376315150 892498299
5-1-2 Test point location for adjustment mode setting
TEL
TEL
13942296513
13942296513
Short-Circuit for few seconds and release.
(Just one time)
Fig. 5-2 Main PCB (Top View)
www
.
x iao y u163. co m
5-2
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
QQ 376315150 892498299
5-2 MECHANICAL ADJUSTMENT
Note : Refer to the Mechanical Manual for the adjustment and confirmation of ass’y deck.
5-2-1 The number and position of test point
Test point :
TP601 (Control Pulse)
TP602 (H’D S/W -Trigger)
TP301 (Envelope)
TP302 (Audio output)
TP303 (Video output)
TEL
TEL
13942296513
13942296513
AUDIO OUTPUT
ENVELOPE
HEAD SWITCHING
Fig. 5-3 Location of Test point (Main PCB-Top View)
5-2-2 ACE Head Position (X-Point) Adjustment
(See the 2-2-1(d) ACE Head Position (X-Point) Adjustment on
page 2-2 of the Mechanical Manual)
1) Playback the alignment tape (KRV-52NE (NTSC)/52PL
(PAL)).
2) Monmently short-circuit the test point on Main PCB with
pincers to set the adjustment mode.
(See Fig. 5-2)
3) Press the “5” button of remote control then adjustment is operated automatically. (See Fig. 5-1)
www
.
4) Connect the CH-1 probe to TP301 (Envelope) the CH-2
probe to TP602 (H’D switching pulse) and then trigger
to CH-1.
5) Insert the (-) driver into the X-Point adjustment hole
and adjust it so that envelope waveform is maximum.
x iao y u163. co m
5-3
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
QQ 376315150 892498299
5-3 HEAD SWITCHING POINT ADJUSTMENT
1) Playback the alignment tape.
2) Monmently short-circuit the test point on Main PCB with pincers to set the adjustment mode. (See Fig. 5-2)
3) Press the “SP/EP” button of remote control then adjustment is operated automatically. (See Fig. 5-1)
4) Turn the Power off.
TEL
TEL
13942296513
13942296513
.
x iao y u163. co m
5-4E
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
QQ 3763 1515 0 89 2498 299
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 376315150 892498299
6. REPAIR PARTS LIST
Page
6-1-1 Instrument Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
6-2
6-1-2 Mechanical Parts (Top Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
6-3
6-1-3 Mechanical Parts (Bottom Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
6-4
6-2 Electrical Parts List - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
6-5
.
x iao y u163. co m
6-1
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
QQ 3763 1515 0 89 2498 299
QQ
QQ
TEL 13942296513
13942296513
13942296513
6-2
TEL
TEL
6-1 Exploded Views - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
http://www.xiaoyu163.com
QQ 376315150 892498299
6-1 EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
• Abbreviation
CS : Chile model, Peru model
MX : Mexican model
The components identified by mark 0or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
6-1-1 Instrument Assembly
not supplied
7
4
12
TEL
TEL
TM401B
13942296513
13942296513
not supplied
not supplied
6
not supplied
5
376315150 892498299
not supplied
3763 1515 0 89 2498 299
9
not supplied
1
2
1
2
not supplied
not supplied
not supplied
3
not supplied
not supplied
LX500
LX600S/LX700S
Ref. No.
1
1
1
2
2
3
4
05
05
Part No.
Description
3-085-232-01
3-085-233-01
3-085-234-01
3-085-227-01
Ref. No.
Remarks
F PANEL BLOCK ASSY (LX700S)
F PANEL BLOCK ASSY (LX600S)
F PANEL BLOCK ASSY (LX500)
DOOR (LX700S, LX600S), CASSETTE
(LX600S/LX700S)
3-085-228-01 DOOR (LX500), CASSETTE (LX500)
www
1-786-352-11
3-075-236-01
1-823-023-11
1-824-058-11
6
7
9
9
Description
Remarks
3-075-256-01
3-075-262-01
1-477-306-11
1-477-307-11
SCREW TAP 3X12
SCREW BH 4X12
COMMANDER, STANDARD (RMT-V403) (LX500)
COMMANDER, STANDARD (RMT-V404)
(LX600S/LX700S)
3-075-088-01 COVER (S) REMOTE CONTROL BATTERY
(for RMT-V403/V404)
x iao y u163. co m
10
SW-DIAL TIMER (LX600S/LX700S)
CASE (NT360), UPPER
POWER CORD KKP419C (LX700S: CS)
POWER CORD KKP211 (EXCEPT LX700S: CS)
.
Part No.
12
3-084-084-01 ASSY DECK
TM401B 3-085-225-01 COVER, JACK TERMINAL (LX600S/LX700S)
TM401B 3-085-226-01 COVER, JACK TERMINAL (LX500)
6-2
http://www.xiaoyu163.com
376315150 892498299
QQ
TEL 13942296513
not supplied
QQ
QQ
10
http://www.xiaoyu163.com
QQ 376315150 892498299
6-1-2 Mechanical Parts (Top Side)
not supplied
109
108
not supplied
112
not
supplied
not supplied
110
not
supplied
TEL
TEL
not
supplied
not
supplied
13942296513
13942296513
114
not supplied
107
127
115
116
106
118
124
104
113
not supplied
103
not
supplied
not supplied
120
123
not supplied
not
supplied
102
121
101
111
Part No.
Description
Part No.
Description
101
102
103
104
105
3-067-779-01
3-067-780-01
3-067-785-01
3-067-786-01
3-067-782-01
LEVER-#9 GUIDE
SPRING-#9 GUIDE
LEVER-T. BRAKE
SPRING-BRAKE
SPRING-TENSION LEVER
112
113
114
115
116
3-067-784-01
3-075-257-01
3-075-241-01
3-067-789-01
3-079-356-01
LEVER-UNIT PINCH
SCREW TAP 2.6X5
ASSY HEAD ACE
GUIDE-CASS. DOOR
POST #8 GUIDE ASSY
106
107
108
109
109
3-067-781-01
3-067-783-01
3-067-788-01
1-787-013-11
1-787-041-11
LEVER-TENSION
BAND-BREAK
HOLDER-FL CASS.
ASSY CLYNDER (NTSC 6HD) (LX600S/LX700S)
ASSY CLYNDER (NTSC 4HD) (LX500)
118
120
121
123
124
1-796-434-11
3-075-704-01
3-067-796-01
3-075-046-01
3-075-047-01
LOADING ASSY, MOTOR
LEVER-FL DOOR
PLATE-GROUND DECK
DISK T REEL
DISK S REEL
110
111
3-084-091-01 SCREW TAP 2.6X5
3-075-254-01 SCREW ASSY MAC 3X6
126
127
3-075-022-01 AUTO HEAD CLEANER (G681)
3-075-021-01 AUTO HEAD CLEANER (G680)
Ref. No.
www
.
Ref. No.
Remarks
x iao y u163. co m
6-3
http://www.xiaoyu163.com
Remarks
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
126
QQ
QQ
105
http://www.xiaoyu163.com
QQ 376315150 892498299
6-1-3 Mechanical Parts (Bottom Side)
151
TEL
TEL
not supplied
not supplied
not supplied
13942296513
13942296513
152
not
supplied
376315150 892498299
not
supplied
not supplied
not
supplied
not supplied
not supplied
153
www
Ref. No.
151
152
Part No.
Description
.
x iao y u163. co m
Ref. No.
Remarks
3-067-790-01 BELT-PULLEY
1-796-432-11 MOTOR CAPSTAN
153
Part No.
Description
3-075-259-01 SCREW CAP 2.6X6
6-4
http://www.xiaoyu163.com
Remarks
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
QQ
QQ
not supplied
http://www.xiaoyu163.com
QQ 376315150 892498299
MAIN
6-2 ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, and -X mean standardized parts, so they
may have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• Not all of the parts are listed.
Part No.
•
•
•
Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
CAPACITORS:
uF: µF
COILS
uH: µH
Description
Ref. No.
Remarks
FC1SS1
FC1SS2
LD601A
S601A
S602A
1-576-527-11
1-576-527-11
3-075-959-01
3-075-066-01
3-075-066-01
FUSE CLIP
FUSE CLIP
HOLDER-LED
HOLDER-SENSOR
HOLDER-SENSOR
TM401B 3-085-225-01 COVER, JACK TERMINAL (LX600S/LX700S)
TM401B 3-085-226-01 COVER, JACK TERMINAL (LX500)
0 C1SD01 1-100-643-11 CONDENSER CERAMIC DISC 10000PF
0 C1SR07 1-165-573-11 CONDENSER FILM
0.1uF
1-815-685-11
1-815-688-11
1-817-805-11
1-815-692-11
Description
D709
D804
D1P106
D1P109
1-804-416-11
1-804-416-11
1-804-407-11
1-804-407-11
DIODE
DIODE
DIODE
DIODE
MTZJ5.1B
MTZJ5.1B
IN4148
IN4148
D1SS01
D1SS02
D1SS03
D1SS04
D1SS05
1-804-413-11
1-804-413-11
1-804-413-11
1-804-413-11
1-804-408-11
DIODE
DIODE
DIODE
DIODE
DIODE
IT5
IT5
IT5
IT5
UF4007
D1SS06
D1SS07
D1SS08
D1SS09
D1SS10
1-804-412-11
1-805-308-11
1-804-412-11
1-804-413-11
1-804-411-11
DIODE
DIODE
DIODE
DIODE
DIODE
FIT4
SHK55-65
FIT4
IT5
UG2D
D1SS11
D1P108
ZD1P01
ZD1P02
ZD1P03
1-804-412-11
1-804-407-11
1-804-414-11
1-804-416-11
1-804-417-11
DIODE
DIODE
DIODE
DIODE
DIODE
FIT4
IN4148 (LX600S/LX700S)
UZP33B
MTZJ5.1B
MTZJ9.1B (LX600S/LX700S)
Remarks
QQ 3763 1515 0 89 2498 299
< CONNECTOR >
CN301
CN303
CN701
CN1SS1
Part No.
CONNECTOR FPC 10P
CONNECTOR FPC 6PSN
CONNECTOR HEADER
CONNECTOR HEADER 2P
ZD1P04 1-804-417-11 DIODE MTZJ9.1B (LX500)
ZD1P05 1-804-418-11 DIODE MTZJ12B
< DIODE >
D503
D506
D507
D601
D603
1-804-407-11
1-804-407-11
1-804-407-11
1-804-407-11
1-804-409-11
DIODE
DIODE
DIODE
DIODE
DIODE
IN4148 (LX600S/LX700S)
IN4148 (LX600S/LX700S)
IN4148 (LX600S/LX700S)
IN4148
IN4002
D604
D605
D606
D607
D701
1-804-409-11
1-804-407-11
1-804-409-11
1-804-409-11
1-804-407-11
DIODE
DIODE
DIODE
DIODE
DIODE
IN4002
IN4148
IN4002
IN4002
IN4148
D702
D703
D704
D705
D706
1-804-407-11
1-804-407-11
1-804-407-11
1-804-407-11
1-804-407-11
DIODE
DIODE
DIODE
DIODE
DIODE
IN4148
IN4148
IN4148
IN4148
IN4148
D708
1-804-407-11 DIODE IN4148
< DISPLAY >
DT701
DT701
1-518-826-11 4DIGIT LED DISPLAY(NA/J) (LX500)
1-518-921-11 LED DISPLAY (LATIN) (LX600S/LX700S)
< FUSE >
www
.
0 F1SD01 1-576-525-11 FUSE (1.6A/250V) (LX500,LX600S/LX700S: MX)
0 F1SD01 1-576-526-11 FUSE T.L (1.6A/250V) (LX700S: CS)
< IC >
IC601
IC MICOM
IC603
1-804-431-11 IC 24C021
IC6B1
1-804-807-11 IC RESET
IC1SD1 1-805-309-11 IC PWM CONTROLLER
(LX500/LX600S/LX700S: MX)
IC1SD1 1-805-372-11 IC PWM CONTROLLER (LX700S: CS)
x iao y u163. co m
0 IC1SS1 1-804-784-11 IC PHOTO COUPLER
IC1SS2 1-804-445-11 IC KA4318
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
6-5
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
QQ
QQ
< CAPACITOR >
When indicating parts by reference number,
please include the board name.
13942296513
13942296513
MAIN BOARD
***********
• Abbreviation
CS: Chile model, Peru model
MX: Mexican model
TEL
TEL
Ref. No.
•
http://www.xiaoyu163.com
QQ 376315150
MAIN
Ref. No.
Part No.
Description
Remarks
Ref. No.
< COIL >
Q1P102
Q1P104
Q1P107
Q1P108
L301
L302
L303
L304
L305
1-400-085-11
1-400-086-11
1-400-086-11
1-400-086-11
1-400-086-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
0uH
0uH
0uH
0uH
0uH
L502
L503
L601
L603
L802
1-400-086-11
1-400-086-11
1-400-086-11
1-400-086-11
1-400-086-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
0uH (LX600S/LX700S)
0uH (LX600S/LX700S)
0uH
0uH
0uH
0 L1SS01
L1SS02
L1SS03
W008
1-424-831-11
1-424-828-11
1-424-828-11
1-400-086-11
LINE FILTER
COIL CHOKE
COIL CHOKE
INDUCTOR
20mH
10uH
10uH
0UH
Part No.
89 249 82 99
1-804-424-11
1-804-421-11
1-804-424-11
1-804-429-11
Description
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Remarks
KSC2328AY
KSC945 (LX600S/LX700S)
KSC2328AY
KSR2001
Q1P109 1-804-421-11 TRANSISTOR KSC945
< RESISTOR >
R1SF05
R1SS01
R1SS02
R1SS05
R1SS06
TEL
TEL
RM701
1-805-311-11 REMOCOM MODULE GP1UA291QK
< PHOTO TRANSISTOR >
1-804-438-11 LED-IR (T/S LED)
S601
S602
1-804-439-11 PHOTO TRANSISTOR (END SENSOR)
1-804-439-11 PHOTO TRANSISTOR (START SENSOR)
1-804-770-11 PHOTO INTERRUPTER (S REEL)
1-804-770-11 PHOTO INTERRUPTER (T REEL)
< SWITCH >
SW602
SW603
1-786-199-11 SWITCH REC (REC SWITCH)
1-786-198-11 SWITCH MODE (PROGRAM SWITCH)
< TUNER >
< TRANSISTOR >
TM401
Q302
Q303
Q304
Q305
Q306
1-804-420-11
1-804-421-11
1-804-420-11
1-804-422-11
1-804-420-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KSA733
KSC945
KSA733
KTC3023
KSA733
Q307
Q308
Q601
Q701
Q702
1-804-422-11
1-804-422-11
1-804-428-11
1-804-419-11
1-804-419-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KTC3023
KTC3023
KSR1004
KSA643Y (LX600S/LX700S)
KSA643Y
Q703
Q704
Q705
Q706
Q707
1-804-419-11
1-804-419-11
1-804-419-11
1-804-421-11
1-804-421-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KSA643Y
KSA643Y
KSA643Y
KSC945
KSC945 (LX600S/LX700S)
Q708
Q709
Q710
Q711
Q712
1-804-421-11
1-804-421-11
1-804-421-11
1-804-421-11
1-804-421-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KSC945
KSC945
KSC945
KSC945
KSC945
Q713
Q714
Q715
Q716
Q801
1-804-421-11
1-804-421-11
1-804-421-11
1-804-421-11
1-804-420-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
1-693-638-11 TUNER NTSC TMZH2002A
< VARISTOR >
0 VA1SS1 1-804-437-11 VARISTOR
< VIBRATOR >
www
.
XT301
XT601
XT602
1-795-629-11 CRYSTAL (3.579545MHz)
1-795-996-11 CRYSTAL UNIT (14.318448MHz)
1-795-332-11 VIBRATOR CRYSTAL (32.768kHz)
ACCESSORIES & PACKING MATERIALS
********************************
1-477-306-11 COMMANDER, STANDARD (RMT-V403) (LX500)
1-477-307-11 COMMANDER, STANDARD (RMT-V404)
(LX600S/LX700S)
3-075-088-11 COVER (S) REMOTE CONTROL BATTERY
(for RMT-V403/V404)
3-081-607-11 MANUAL, INSTRUCTION
x iao y u163. co m
KSC945
KSC945
KSC945
KSC945
KSA733
Q1P101 1-804-424-11 TRANSISTOR KSC2328AY
6-6E
http://www.xiaoyu163.com
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
376315150 892498299
376315150 892498299
QQ 3763 1515 0 89 2498 299
TEL 13942296513
0 PT1SD1 1-439-934-11 TRANS SWIT EE2621
QQ
QQ
< TRANSFORMER >
13942296513
13942296513
< MODULE >
< PHOTO INTERRUPTER >
PT601
PT602
RESISTOR
2.7 (LX700S: CS)
R-METAL OXIDE (S)
R-METAL OXIDE (S)
RESISTOR
3K
RESISTOR
2.2K
R1SS11 1-245-575-11 R-METAL OXIDE
< LED >
LD601
1-244-373-11
1-245-556-11
1-245-556-11
1-244-372-11
1-244-371-11
http://www.xiaoyu163.com
SLV-LX500/LX600S/LX700S
QQ 376315150 892498299
TEL
TEL
13942296513
13942296513
9-929-749-11
.
x iao y u163. co m
Sony Corporation
Home Video Company
— 58 —
http://www.xiaoyu163.com
2003D0500-1
©2003.4
Published by Customer Support Center
376315150 892498299
376315150 892498299
www
QQ 3763 1515 0 89 2498 299
QQ
QQ
TEL 13942296513
Download PDF
Similar pages