NBX Administrator'

NBX® Administrator’s Guide
V3001 Analog
V3001 BRI
V3001R
V3000 Analog
V3000 BRI
V5000
Release 6.5
Part Number 900-0212-01 AB
Published April 2009
http://www.3com.com/
3Com Corporation
350 Campus Drive
Marlborough, MA
01752-3064
Copyright © 1998 – 2009, 3Com Corporation. All Rights Reserved. No part of this documentation may be
reproduced in any form or by any means or used to make any derivative work (such as translation,
transformation, or adaptation) without written permission from 3Com Corporation.
3Com Corporation reserves the right to revise this documentation and to make changes in content from
time to time without obligation on the part of 3Com Corporation to provide notification of such revision
or change.
3Com Corporation provides this documentation without warranty, term, or condition of any kind, either
implied or expressed, including, but not limited to, the implied warranties, terms, or conditions of
merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may make improvements
or changes in the product(s) and/or the program(s) described in this documentation at any time.
If there is any software on removable media described in this documentation, it is furnished under a
license agreement included with the product as a separate document, in the hardcopy documentation, or
on the removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to
locate a copy, please contact 3Com and a copy will be provided to you.
UNITED STATES GOVERNMENT LEGENDS:
If you are a United States government agency, then this documentation and the software described herein
are provided to you subject to the following:
United States Government Legend: All technical data and computer software is commercial in nature
and developed solely at private expense. Software is delivered as Commercial Computer Software as
defined in DFARS 252.227-7014 (June 1995) or as a commercial item as defined in FAR 2.101(a) and as
such is provided with only such rights as are provided in 3Com’s standard commercial license for the
Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov
1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any
portion of any legend provided on any licensed program or documentation contained in, or delivered to
you in conjunction with guide.
Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or
may not be registered in other countries.
3Com, the 3Com logo, and NBX are registered trademarks of 3Com Corporation. NetSet and pcXset are
trademarks of 3Com Corporation.
Other brand and product names may be registered trademarks or trademarks of their respective holders.
CONTENTS
ABOUT THIS GUIDE
How to Use This Guide 17
Conventions 18
International Terminology 18
Your Comments 19
1
INTRODUCTION
Network-based Telephony 21
NetSet Administration Utility 22
NetSet User Interface 23
2
SYSTEM SETTINGS
Auto Discovery 25
Initial System Configuration 26
Disabling the Auto Discovery Feature 28
Enable Features System-Wide 28
How Call Timer Works With Other Telephone Features
System Identity 30
Business Information 32
System Mode 32
Business Hours 32
Date and Time 33
System Date and Time 33
Simple Network Time Protocol (SNTP) 34
IP Settings 34
Audio Settings 34
Compression Overview 35
Codec Selection 36
Codecs and NBX Devices 38
Silence Suppression Overview 39
Timers 40
29
4
Multicast Addresses
3
41
FEATURE SETTINGS
Account Codes 43
Feature Interaction 44
Account Codes: Operational Modes 46
Call Pickup 49
Group Numbers 49
Call Park 51
Adding a Call Park Extension 51
Changing a Call Park Extension Name 51
Removing a Call Park Extension 51
Page Zones 52
Page Zone Feature Support 52
Ring Patterns 53
Supervisory Monitoring 53
Introduction to Monitoring 54
Domains and Upgrades 55
Domains and Privacy 56
Announcement Tones and Supervisory Modes
Supervisory Monitoring Usage Notes 61
Supervisory Monitoring Error Conditions 63
Speed Dials 65
WhisperPage 66
WhisperPage Permissions 68
Using Domains For WhisperPage 68
Feature Interaction With Whisper Page 69
WhisperPage Restrictions 70
4
SYSTEM MAINTENANCE
System Backup 73
System Restore 76
Import / Export Data 77
Reboot/Shutdown 78
Password Administration 79
Call Report Settings 80
CDR Changes At Release R6.0
80
58
5
Windows Environment Specifications 82
Installing Call Reports 83
Configuring Call Reporting 83
Purge CDR 83
Purge Database 84
Purge Database and CDR 84
Purge All Voice Mail 84
Manage Data 84
Migration 85
Restore Database From Another Version 87
Disk Mirroring 87
Adding a Mirror Disk 87
Verifying a Failed Disk Drive 90
Reverting to a Single-Disk System 90
5
TELEPHONE CONFIGURATION
Adding, Removing, and Modifying Telephones 93
Adding a New Telephone 93
Modifying a Telephone 95
Checking a Telephone’s Status 96
Removing a Telephone 96
Rebooting a Telephone 96
Adding a Remote Telephone 97
Remote NAPT Telephone Configuration 97
Creating and Managing Bridged Extensions 98
Example Bridged Extensions Configurations 100
Defining Bridged Extensions 101
Defining Bridged Extensions on a Primary Telephone 102
Defining Bridged Extensions on a Secondary Telephone 103
Defining Bridged Extensions on 3103 Manager’s Telephones 104
Modifying Bridged Extensions 107
Sample Calling Situations Using Bridged Extensions 107
Viewing Bridged Extension Information 108
Camp On Feature and Bridged Extensions 109
Creating and Managing Telephone Groups 109
Creating a New Telephone Group 110
Modifying a Telephone Group 110
6
Removing a Telephone Group 110
Viewing Telephone Group Membership 111
Recording and Monitoring Telephone Calls 111
Recording Calls Between Telephones with Different Recording
Settings 112
Remote Telephones 112
Music On Hold (MOH) 112
Non-3Com Telephones 113
Creating and Managing Button Mappings 113
Mapping Access Buttons 114
Mappings for Telephone Users and Groups 115
Creating a Busy Lamp/Speed Dial Button Mapping 116
Creating a Delayed Ringing Pattern 116
Creating Groups and Button Mappings 117
Changing Device IP Settings 118
Configuring the 3Com Attendant Console 120
Adding an Attendant Console 120
Modifying an Attendant Console 121
Viewing Attendant Console Status 121
Removing an Attendant Console 122
Configuring Attendant Console Buttons 122
Changing Attendant Console IP Settings 123
Configuring Connectivity to a 3105 Attendant Console Through the
Serial Port 124
Connecting and Managing Analog Devices 126
Adding an Analog Terminal Card 126
Adding an Analog Terminal Adapter (ATA) 128
Modifying an Analog Terminal Port 129
Removing an Analog Terminal Adapter 129
Viewing The Status of an Analog Terminal Adapter 129
Advanced Settings 130
6
USER CONFIGURATION
Users 131
Phantom Mailboxes 131
Class of Service (CoS) 132
7
7
CALL DISTRIBUTION GROUPS
Automatic Call Distribution (ACD) 135
ACD Groups 136
ACD Shifts 139
Estimated Wait Time Announcements 140
In-Queue Digit Processing and Announcements 142
ACD Group Open/Close and Announcements 142
Announcements for SIP-Mode Systems 143
Wrap-Up Time 143
Streaming ACD Data Through a TCP Socket 144
ACD Considerations 144
Hardware Limits for ACD Groups 145
ACD Operations With Call Detail Reports (CDR) 145
Display Data 145
Voice Mail Port Usage 145
Using ACD 146
ACD Groups 146
ACD Announcements 148
ACD Agents 150
ACD Statistics 151
Hunt Groups 154
Linear and Circular Hunt Groups 155
Calling Groups 156
Call Coverage 156
Hunt Group Supervisory Monitoring 157
8
PSTN GATEWAY CONFIGURATION
Configuring and Managing Analog Line Card Ports 159
Configuring a Line Card Port 160
Modifying a Line Card Port 162
Removing a Line Card Port 162
Verifying Line Card Port Status 163
Rebooting a Line Card Port 163
Advanced Settings 163
Configuring and Managing Digital Line Cards 164
Adding a Digital Line Card 165
Configuring the Digital Line Card 168
8
169
Digital Line Card Status Lights 172
Modifying a Digital Line Card 175
Support of AT&T’s 4ESS Switch Protocol 178
Adding or Modifying a Digital Line Card Group 179
Modifying Card Channels 182
Modifying IP Settings 184
Removing a Digital Line Card 185
Setting Up a Digital Line Card at a Remote Location 185
Setting Up T1/E1 Logging 187
Viewing CSU State Information and Statistics 187
T1.231 Near End 188
T1.231 Far End 189
TR54016 Near End 189
TR54016 Far-End 189
G.826 Near End 189
G.826 Far End 190
Using Loopback Tests 190
Enabling or Disabling Loopback Tests 191
Obtaining a Dial Tone from a PBX System 192
9
NBX MESSAGING
Group List 197
NBX Voice Mail 198
Voice Mail Extensions 201
Voice Mail Passwords 201
IMAP for Integrated Voice Mail 201
Configurable Operators 202
Off-site Notification 205
Status 206
Port Usage 207
User Usage 207
Auto Attendant 208
Overview of Auto Attendant Features 208
Adding an Auto Attendant 210
Adding an Accessible (TTY) Auto Attendant 221
Managing Auto Attendants 223
9
Voice Application Setup Utility 225
Testing the Auto Attendant 226
Voice Profile for Internet Mail 227
Control Parameters 228
Operations Management 229
Statistics 230
Advanced Settings 231
Configuring Domain Name Server Information
10
234
SIP-MODE OPERATIONS
Overview of SIP Mode on the NBX Platform 235
SIP Mode Operations 235
Device Support Details 238
Feature Support 239
Platforms Supported 240
Licensing and Resource Limits 241
Dial Plan Considerations 242
SIP Mode and ACD 243
Other Applications Support 243
Call Log Support 243
SNMP Support 243
SysLog Support 243
CDR Support 244
Enabling and Configuring SIP Mode 244
Install and Configure the System for SIP Mode 244
Enable SIP Mode 245
Disable SIP Mode 245
Add Messaging 246
Create Mailboxes 247
Force Mailbox Creation 248
Configure Auto Attendants 248
Configure Music on Hold 249
Configure ACD Delayed Announcements 250
Add Trusted SIP Interfaces 253
Add an Optional IP Conferencing Module 254
Adding Telephone Users and Devices 258
Adding a Generic SIP Telephone 258
10
Adding a 3Com 3108 Wireless Telephone
11
260
DIAL PLAN
Dial Plan Concepts and Overview 261
Call Process Flow 263
Inbound and Outbound Call Processing 263
System Database 264
System Dial Plan 264
Pretranslation 265
Routing 265
System Features Affected by the Dial Plan Configuration 266
Dial Plan Tables 267
Dial Plan Command Format 268
Internal Dial Plan Table 272
Incoming Dial Plan Table 272
Least Cost Routing Dial Plan Table 273
Adding New Dial Plan Tables 273
Dial Plan Pretranslators 274
Pretranslators for Incoming Calls 275
Pretranslators for Certain Outgoing Calls 276
Managing the Dial Plan Configuration File 277
Accessing the Dial Plan 278
Creating Dial Plan Configuration Files 278
Importing and Exporting Dial Plan Configuration Files 279
Importing a User-Defined Dial Plan 281
Exporting (Saving) a Dial Plan Configuration File 282
Testing a Dial Plan 283
Generating a Dial Plan Report 284
Modifying a Dial Plan Configuration File 285
Outdialing Prefix Settings 286
Managing Extensions 286
Extension Settings Overview 286
Changing Extension Length and Ranges 290
How Auto Discovery Assigns Extensions 291
Modifying Extensions 292
Converting Extensions 292
Managing Extension Lists 294
11
Adding an Extension List 296
Modifying an Extension List 297
Removing an Extension List 298
Managing Dial Plan Tables 298
Determining Which Devices Use Dial Plan Tables 298
Removing a Dial Plan Table 299
Managing Dial Plan Pretranslators 300
Identifying Devices Using Pretranslators 300
Creating a Pretranslator for VTL Calls 301
Identifying Devices Using Pretranslators for CLI 303
Removing a Pretranslator from the Dial Plan 304
Configuring the Dial Plan for the 4ESS Protocol (T1) 304
Dial Plan Configurations and VPIM 306
Configuring the Dial Plan for VPIM 307
Dial Plan Configuration File Commands 309
Dial Plan Command Summary 309
List of Dial Plan Commands 311
Sample Solutions Using Dial Plan Configuration File Commands
12
VIRTUAL CONNECTIONS
Overview of Virtual Tie Lines 333
VTL Connections Using Unique Extension Ranges 334
VTL Connections Using Site Codes 335
Conference Calls Using VTL Connections 336
How to Configure a Virtual Tie Line 338
License Installation 338
Dial Plan Configuration 339
Updating the Extension List 342
Adding VTL Devices to the Pretranslators (Optional) 343
Verification of the Virtual Tie Line 344
Call Rerouting for Virtual Tie Lines 346
Example Dial Plan Entries 346
Managing Existing Virtual Tie Lines 348
Modifying a Virtual Tie Line Name 348
Viewing and Resetting Virtual Tie Line Statistics 348
Enabling Audio Compression for VTL Calls 349
Enabling Silence Suppression on VTL Calls 350
324
12
Using a VTL Password 350
Configuring a VTL Password 351
Configuring VTL Passwords in the Dial Plan 351
Toll Calls Without a VTL Password 354
Music On Hold 354
Troubleshooting VTL Calls 354
TAPI Route Points 356
Redirect Behaviors 356
TAPI Route Point Capacities 358
Creating a TAPI Route Point 358
Modifying a TAPI Route Point 358
Viewing TAPI Route Point Statistics 359
Specifying TAPI Line Redirect Timeout 359
TAPI Supervisory Monitoring 359
Supervisory Monitoring Modes 360
TAPI Settings 361
13
DOWNLOADS
Software 363
LabelMaker Utility 363
Documentation and Reference Guides
14
364
LICENSING AND UPGRADES
Licenses 365
Add a License 366
Remove a License 366
Usage Report 367
Backing Up Licenses 367
Restoring Backed-Up Licenses 367
Obtaining Details of License History 367
Software Upgrade 368
System Software Licensing 369
Restricted Operation 370
Considerations 371
Customer Service 371
Third-Party Drivers 372
Software Upgrades 372
13
Third-Party Telephone Groups
15
REPORTS
Directory 373
Device List 373
System Data 374
Disk Status 374
Power Supply Status
16
372
374
NETWORK MANAGEMENT
SNMP 375
Terminology and Acronyms 377
SNMP Managers and Agents 377
SNMP Security 378
Community Strings 378
User-based Security Model (USM) 379
View-based Access Control Model (SNMPv1, SNMPv2c and
SNMPv3) 379
Traps, Notifications, and Informs 380
Special Considerations 381
MIBs and MIB Objects 381
MIBs Used on the System 382
Standard SNMPv3 MIBs 383
Other IEEE/RFC MIBs 383
3Com MIB Objects 384
Diagnostics for 3Com MIB Objects 386
Persistent Storage 388
Agent Conformance Reference 388
Network Management Applications 390
Applicable Endpoints 390
Syslog 392
Transport Mechanism 393
Terminology 393
3Com Implementation 393
Syslog Message Components 394
PRI (Priority) Message Component 394
Header Component 401
14
MSG Component 404
Syslog Security Considerations 405
Message Forgery 405
Periodic Timestamp on Console (PTOC)
Event Logging 406
Maintenance Alerts 407
17
406
COUNTRY SETTINGS
Regional Software 409
Install Regional Software 410
Remove Regional Software 411
Regional Details 411
Regional Settings 412
18
TROUBLESHOOTING
Telephone Local User Interface Utility
415
Using the LUI Utility 416
Using the LUI Menu Options 425
The 3Com Telephone Local Configuration Application 433
Installing the 3Com Telephone Local Configuration Application
Using the Telephone Local Configuration Application 433
Using H3PingIP 434
System-level Troubleshooting 434
Digital Line Card Troubleshooting 436
Alarm Conditions (Overview) 437
Alarm Descriptions 438
Alarms on NBX Digital Line Cards 439
Configuration and Status Reports 440
Connecting a Computer to a Serial Port 447
Servicing the Network Call Processor Battery 449
Getting Service and Support 449
A
INTEGRATING THIRD-PARTY MESSAGING
Installing Software on the Third-Party Messaging Server
Configuring the System 452
Configuring NBXTSP on the Server 453
451
433
15
B
ISDN COMPLETION CAUSE CODES
C
CONFIGURING OPTION 184 ON A WINDOWS 2000 DHCP
SERVER
Overview 461
Creating Option 184 462
Editing Option 184 Values 462
Activating Option 184 463
D
CALLER ID
Forwarded Calls and Caller ID 465
Calls That Are Forwarded Multiple Times 465
Long Caller ID Character Strings 466
Specific Caller ID Situations 466
Analog Terminal Adapter and Analog Terminal Card Ports
3Com Legacy Link or Citel Analog Interface Card 467
Bridged Extension Telephones 467
External Calls 467
Internal Calls 468
Nortel Phones 468
Parked Calls 469
Second Incoming Call 469
TAPI Calls 469
TAPI Redirected Calls 469
VTL Calls 469
Calls Transferred to Hunt Groups 469
3Com Cordless Calls 469
E
OUTBOUND CALLER ID AND 911 SERVICE
Sample Dial Plan 472
Internal 3-Digit Extensions 472
Incoming DID Section 472
Least Cost Routing Portion 473
Pretranslators (Part 1) 474
Pretranslators (Part2) 475
466
16
F
NBX ENTERPRISE MIB
GLOSSARY
INDEX
3COM CORPORATION LIMITED WARRANTY
FCC CLASS A VERIFICATION STATEMENT
FCC CLASS B STATEMENT
FCC DECLARATION OF CONFORMITY
ABOUT THIS GUIDE
This guide describes how to configure and manage NBX® Networked
Telephony Systems. For information about how to install an NBX system
for the first time, see the NBX Installation Guide.
If the information in the release notes differs from the information in this
guide, follow the instructions in the release notes. Release notes are
available on the NBX Resource Pack DVD.
How to Use
This Guide
Table 1 can help you find information in this guide.
Table 1 Overview of This Guide
An overview of the systems
Chapter 1
Configure system settings
Chapter 2
Configure system features
Chapter 3
Maintain the system
Chapter 4
Configure telephones
Chapter 5
Configure user settings
Chapter 6
Configure Automatic Call Distribution
Chapter 7
Configure and manage digital and analog line cards
Chapter 8
Configure NBX Voice Messaging (voice mail), Auto Attendant, and Chapter 9
Voice Profile for Internet Mail (VPIM)
Enable and configure Session Initiation Protocol (SIP) operation
Chapter 10
Prepare and configure the dial plan
Chapter 11
Configure Virtual Tie Lines and TAPI Rout Points
Chapter 12
Download optional software and the LabelMaker utility
Chapter 13
Licensing and upgrade information
Chapter 14
Create reports
Chapter 15
Configure SNMP, Syslog, event logging and maintenance alerts
Chapter 16
Install and configure international language settings
Chapter 17
18
ABOUT THIS GUIDE
Table 1 Overview of This Guide
Troubleshooting information
Chapter 18
Third-party messaging system
Appendix A
ISDN Completion Cause Codes
Appendix B
Option 184 on a Windows 2000 DHCP server
Appendix C
Caller ID behavior
Appendix D
Telephony and networking terms
Glossary
References to all topics in this book
Index
FCC and Industry Canada information, Software End-User License page 545
Agreement, and Limited Warranty for Software and Hardware
Conventions
Table 2 lists conventions that are used throughout this guide.
Table 2 Notice Icons
Icon
International
Terminology
Notice Type
Description
Information note
Information that describes important features
or instructions.
Caution
Information that alerts you to potential loss of
data or potential damage to an application,
device, system, or network.
Warning
Information that alerts you to potential personal
injury.
Table 3 lists the United States and international equivalents of some of
the specialized terms that are used in the NBX documentation.
Table 3 International Terminology
Term used in U.S.
Term used outside the U.S.
Toll restrictions
Call barring
Pound key (#)
Hash key (#)
CO (central office)
Telephone Exchange
Toll-free
Free-phone
Analog Line Card
Analog Trunk Line Interface Module
Your Comments
Your Comments
19
Your suggestions are important to us. They help us to make the NBX
documentation more useful to you.
Send comments about this guide or any of the 3Com NBX
documentation and Help systems to:
Voice_TechComm_Comments@3com.com
Please include the following information with your comments:
■
Document title
■
Document part number (found on the front page)
■
Page number
Example:
NBX Administrator’s Guide
Part Number 900-0212-01 Rev AA
Page 25
As always, address all questions regarding the hardware and software to
your authorized 3Com NBX Voice - Authorized Partner.
20
ABOUT THIS GUIDE
1
INTRODUCTION
The NBX Administrator’s Guide explains how to configure your NBX®
system. This chapter describes these topics:
■
Network-based Telephony
■
NetSet Administration Utility
For information about how to install hardware components, see the
NBX Installation Guide.
Network-based
Telephony
3Com Networked Telephony Solutions merge telephony with networking
by delivering business telephone service over a data network.
To a telephone user, a 3Com Telephone is an office telephone. You can
use it to make and receive calls, transfer calls, park calls, use voice mail,
and so on. Inside, the 3Com Telephone is a network device that can
communicate over the LAN using Ethernet frames or IP packets. The
telephone also includes a LAN port. You can connect your computer to
your network through the telephone and avoid the need for a second
LAN connection at the desktop.
The core of the system is the Call Processor. The Call Processor manages
the processes of making and receiving calls, providing voice mail and
Auto Attendant services, and responding to requests for special services,
such as access to the NBX NetSet administration utility, Computer
Telephony Integration (CTI) services, or the system’s IMAP (Internet
Message Access Protocol) server.
22
CHAPTER 1: INTRODUCTION
NetSet
Administration
Utility
the NBX NetSet utility is a browser-based interface that you use to
configure and manage the system. the NBX NetSet utility requires any of
these browsers:
■
Microsoft Internet Explorer 5.5 or higher
■
Netscape Navigator 7.0 or higher
■
Mozilla Firefox 1.0 or higher
Figure 1 shows a sample NetSet window. The navigation menu is on the
left of the window. Place the cursor over any of the functions to expand
the view of that function and display all the associated options.
Figure 1 NetSet Utility - Page Zones Window
Systems present the NBX NetSet utility through an embedded web server
that is integrated in the system software. NetSet passwords grant system
administrators and telephone users different levels of access privileges.
Individual telephone users can view or change their personal settings,
such as personal speed dial lists, off-site notification settings, and ringing
tones. System administrators can manage user profiles and devices,
change system parameters, such as dial plan settings, and upgrade the
system software.
NetSet Administration Utility
NetSet User Interface
23
Figure 2 shows the NBX NetSet utility user interface. Each NetSet user
interface page contains common elements.
Figure 2 User Interface Elements
Navigation Route Bar
Title Bar
Help
Tab Menu Bar
Navigation
Menu
■
Title Bar — The NBX trademark followed by the system (host) name.
■
Navigation Route Bar — The current page location, which is the
selected navigation menu item and the selected submenu item.
■
Navigation Menu — A list of all navigation groups in the NBX NetSet
user interface. The navigation menu is partially or fully disabled under
certain conditions. These conditions include:
■
System backup in progress: All menus are disabled.
■
System restore in progress: All menus are disabled.
■
System shutdown: All menus are disabled.
■
No system license: Only Licensing and Upgrades and System
Maintenance menus are enabled.
■
Tab Menu Bar — Displays when you click a menu item or submenu
item, or when you click a link to a record.
■
Help — Quick help text plus a button that invokes detailed help.
24
CHAPTER 1: INTRODUCTION
2
SYSTEM SETTINGS
This chapter provides information about how to configure settings,
whose effects span the entire system, and includes these topics:
■
Auto Discovery
■
Enable Features System-Wide
■
System Identity
■
Business Information
■
Date and Time
■
IP Settings
■
Audio Settings
■
Timers
■
Multicast Addresses
For more information about these topics and configuration procedures,
see the online Help.
Auto Discovery
The Auto Discovery feature simplifies initial system configuration by
adding information about new devices to the configuration database.
Devices include telephones, Analog Line Card ports, Digital Line Card
channels, Analog Terminal Adapter ports, 3Com Attendant Consoles, and
virtual devices, such as the pcXset Soft Telephone. Devices must have
network connectivity with the Call Processor.
After the system discovers a device, the Auto Discovery process does not
find that device again. To remove a device from the system database, use
the NBX NetSet utility to remove the device and its database record
manually. Note that if you delete a telephone user, the system does not
delete the device associated with that user.
26
CHAPTER 2: SYSTEM SETTINGS
The system does not discover licensed devices until you enter the
appropriate Group License. For more information about Group Licensing,
see the NBX Installation Guide.
Table 4 summarizes Auto Discovery actions for system components.
Table 4 Auto Discovery Actions on System Components
Component
Auto Discover Action
Analog Line Card, and V3000 Gathers configuration information from each port on the card, assigns a default
and V3001 analog line ports extension, and enters the information into the configuration database.
Digital Line Card
Gathers configuration information from the card, assigns a default extension, and
enters the information into the configuration database.
After you Auto Discover the Digital Line Card, you may need to edit the dial plan to
configure Direct Inward Dial (DID) numbers.
3Com Telephones
Gathers configuration information from the telephone, assigns a default User Profile
labeled new user, assigns the next lowest available extension number to the profile,
and enters the information into the configuration database.
Analog Terminal Cards
Analog Terminal Adapters
V3000 and V3001 ATA port
Auto Discover Telephones finds both Analog Terminal Cards and Analog Terminal
Adapters.
By default, the Auto Discover process assigns extension number 1000 (4-digit dial
plan) or 100 (3-digit dial plan) as the first telephone extension. You can use the NBX
NetSet utility to specify a new extension starting number. To simplify Auto Attendant
configuration, start a range at a base number, for example, 1000/100, 2000/200,
3000/300, or 4000/400. The default Auto Attendant assumes that extension 1000
(4-digit dial plan) or 100 (3-digit dial plan) is the extension of a human attendant
(receptionist).
3Com Attendant Console
Finds and configures any installed 3Com Attendant Consoles. The system maps the
first 100 existing telephones, except for the extension that is associated with the
Attendant Console, to Attendant Console buttons. The lowest extension is
automatically associated with the Attendant Console. Typically, you enable Auto
Discover Attendant Consoles after you have installed all your telephones.
pcXset
Soft Telephone
Enables the Auto Discover feature on installations of the pcXset PC Telephone Client
when the following conditions are true:
Initial System
Configuration
■
The pcXset PC Soft Telephone program is running on the host PC.
■
The pcXset PC Soft Telephone host computer is connected to the network.
■
You have entered the proper license key into the NBX NetSet utility.
To use the Auto Discover feature for initial system configuration:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click System-Wide Settings > Enable Features System-Wide.
Auto Discovery
27
3 Verify that the Extensions Start At field is set to what you want, and then
click Apply.
For a 4-digit dial plan, extensions start by default at 1000. For a 3-digit
dial plan, extensions start at 100.
Do not specify a starting extension that begins with zero (0), which will
cause the Auto Discover process to fail.
4 Click System-Wide Settings > Auto Discovery.
5 Select the check box for the device type that you are configuring and click
Apply.
3Com recommends that you Auto Discover one device type at a time. See
the online Help for detailed information about each field.
Auto Discovery Notes
■
If devices are on a different subnetwork from the Call Processor,
enable IP on the Call Processor (System-Wide Settings > IP Settings),
and each device must have IP configuration information.
■
You can use DHCP to configure the telephones. You must configure
the DHCP server to provide the Call Processor IP address through
option 184. Also, you can use the keypad to program IP settings into
each device. See “Configuring Option 184 on a Windows 2000 DHCP
Server” on page 461 for DHCP information and “Telephone Local
User Interface Utility” on page 415 for telephone local programming
instructions.
■
The Auto Discovery and software download processes may take a few
moments to complete. The Call Processor initializes devices one at a
time. If you have connected many new devices to the system at the
same time, the Auto Discovery process requires more time.
■
A fully initialized telephone displays its extension and the date and
time. If there are no extensions available, the Auto Discover process
fails, and the telephone’s display panel continues to display the
telephone’s MAC address.
■
If you are adding devices that do not have a display panel, such as
3100 Entry Telephones, connect the devices one at a time and then
refresh the Telephone Configuration > Telephones list after you
connect a device to see the extension assigned to that device.
■
If you are installing a 3Com Attendant Console, connect it after you
have discovered all of the telephones. The Auto Discover Attendant
28
CHAPTER 2: SYSTEM SETTINGS
Consoles process maps all existing telephone extensions to the
Attendant Console.
Disabling the Auto
Discovery Feature
After you finish the Auto Discovery process for the initial configuration,
disable Auto Discovery so that the Call Processor does not continue to
search for added devices.
To disable the Auto Discovery feature:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click System-Wide Settings > Auto Discovery.
3 Clear all Auto Discover check boxes.
4 Click Apply.
Enable Features
System-Wide
From the System-Wide Setting page, you can make changes to these
settings.
■
Extensions Start at
■
External Prefix
■
RTP DTMF Payload Type
■
Caller ID Wait Timer
■
External Paging Delay
■
External Page Alert Volume
■
Handsfree on Internal Transfer / Camp On
■
Handsfree on External Transfer / Camp On
■
System-wide CLIR
■
One Button Transfer
■
Pulse Dialing
■
Supervisory Monitoring
■
Call Timer
■
Music On Hold
■
Music on Transfer
■
NBX Messaging
Enable Features System-Wide
■
IP Messaging or Third-Party Messaging
■
URL for user access to IP Messaging or third-party messaging
■
Enable SIP
29
To configure system-wide settings:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Enable Features System-Wide.
3 See the online Help for detailed information about the settings and how
to modify them.
How Call Timer
Works With Other
Telephone Features
Table 5 summarizes how Call Timer works with other PBX-type features.
Table 5 Call Timer Behaviors
Feature
Description
Internal Call
The call duration displays on the originating telephone when the
telephone user finishes dialing the destination number. The call
time increments while the called number is ringing.
Call Timer does not work if the caller enters an invalid internal
extension.
External Call
Call Timer behavior for an external call is the same as that of an
internal call except in these cases:
■
If the caller enters an invalid external number
■
If the telephone of the called number is busy
In these cases, the call time continues to advance.
Hold
When you put a call on hold, the system hides the Call Timer
display. However, the Call Timer count continues to increment
during the time that the call is on hold. When you take the call off
hold, the Call Timer reappears.
Transfer
When you transfer a call, the Call Timer count does not carry
forward to the transfer destination. However, during the time
period that the call is ringing on the transfer destination telephone,
the Call Timer count continues to increment on your telephone.
When the telephone user to whom you transferred the call answers
the call, that user sees the Call Timer count start from zero.
30
CHAPTER 2: SYSTEM SETTINGS
Table 5 Call Timer Behaviors
Feature
Description
Conference
Call
The Call Timer value on the telephone that originated the call
increments from the time at which the call originated.
The Call Timer value on each telephone that is added to the
conference increments from the time the conference participant
answered the phone.
If the conference originator drops other parties in the conference
and stays with one party at the end, the Call Timer is based upon
the total time the two parties spent in on the call, including any
time before or during the conference.
Call Park
Call Park behavior is similar to the Transfer feature. However, if the
telephone that unparks the call is the same telephone that parked
the call, Call Timer displays the total time based on the time when
the telephone originated the initial call.
Transfer
Through Auto
Attendant
If the caller dials the main Auto Attendant number, and the Auto
Attendant transfers the call to the extension of choice (or to the
default destination), the called party sees the same behavior as if
the call had been transferred. That is, the Call Timer count at the
transfer destination starts when the called party answers the call.
Bridged Calls
For bridged calls, the Call Timer display depends on the off-hook
indicator.
Example: An administrative assistant answers the phone, and puts
the call on hold. Then, the a site manager picks up the call. The
manager sees the counter start from zero. However, if the
administrative assistant puts the call on hold and retrieves it later,
the administrative assistant sees that the system has defined the
Call Timer display for normal hold.
Example: An administrative assistant puts a call on hold, and the
manager picks up the call and then puts it on hold. Then, the
administrative assistant picks up the call. In this case, the
administrative assistant sees the Call Timer display as if the
administrative assistant had picked up a new call.
System Identity
The System Identity window shows the current system settings, such as
the software version, the IP address of the system, and the amount of
free memory. To view system settings:
1 Click System-Wide System Settings > System Identity.
Table 6 describes the System Settings fields.
System Identity
31
Table 6 System Settings
Field
Purpose
Software Version
The call control software for the system.
System Serial #
The serial number on the Call Processor circuit board.
Host Name
This is an IP setting. It is a name you can give to the system
so you do not have to specify the IP address when you
access the NBX NetSet utility through a browser.
IP Address
The IP address of the system.
Default Gateway
The IP address of the destination host for any IP packet not
addressed to a host on the local subnetwork.
Subnet Mask
An IP setting that identifies the network and host portions
of an IP address on the network.
Network Protocol
The transport mechanism for voice packets.
Ethernet only: All communications are at the Ethernet
frame layer.
Standard IP: IP communications are used for traffic
between NBX system addresses. Every device needs an
IP address.
IP On-the-Fly: An implementation of IP communications in
which Layer 2 (Ethernet) devices temporarily use a Layer 3
(IP) address only when those devices need to communicate
with a Layer 3 device on a different subnetwork. The
system administrator defines an address pool that assigns
the IP address. After the Layer 2 device returns to the idle
state, the IP address returns to the pool of available
addresses for future use.
System MAC Address
The hardware address of the system.
MOH MAC Address
The hardware address of the Music-on-Hold (MOH) device.
Free Memory
Available memory on the system.
Memory Upgrade
Installed
Indicates whether this system has had a memory upgrade.
Possible values are:
File System
■
Yes (V3000, V3001, V5000 systems)
■
No (V3000, V3001, V5000 systems)
■
N/A (NBX 100, V3001R systems)
The file system this system uses.
■
NBXFSV1 - The pre-release R6.0 file system.
■
NBXFSV2 - The newer file system that is shipped with
release R6.0 or higher systems, which offers better
performance and upgrade capabilities.
If you upgrade an existing system to release R6.0, the
system continues to use NBXFSV1.
32
CHAPTER 2: SYSTEM SETTINGS
Table 6 System Settings (continued)
Business
Information
Field
Purpose
Date and Time
The current system date and time. To modify, click
System-Wide Settings > Set Date and Time.
System Start Time
The last time you initialized the system (boot time).
You can configure information about the your business, such as business
address and hours, including time of day service modes. You can also
view the current mode and force the system into a different mode.
To enter business information:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Business Information.
3 See the online Help for procedures to modify these types of information:
■
Business information
■
Business hours
■
System mode
Click the Business Identity tab to display the information that you
configure in the Business Information, Business Hours, and System Mode
windows.
System Mode
The System Mode window lets you specify that the system operate in a
particular mode or automatically. If necessary, you can force the system
into a specific Time of Day Service mode without changing other system
settings, such as Business Hours. If the system is in Automatic mode, it
constantly compares the current time of day and day of week with the
settings you establish in the Business Hours window (click System-Wide
Settings > Business Information and click the Business Hours tab).
Business Hours
The Business Hours window allows you to define business hours for three
separate service modes: Open, Lunch, and Other. Any time period that
does not fall within these specified hours is considered Closed. Business
hours link directly to time-of-day service modes and can affect other
settings in the system, such as the Auto Attendant.
Date and Time
33
If the system mode is set to Automatic, the system constantly compares
the current time of day and day of week with the business hour tables.
The system knows the current day of the week and proceeds across the
tables in a sequential manner, looking for business hours that match the
current time of day. The system examines the three tables sequentially:
first the Other mode, then the Lunch mode, and then the Open mode.
The system moves across the tables until it finds a match. It skips a blank
table.
Date and Time
System Date and
Time
The Date and Time window allows you to configure the following:
■
System Date and Time
■
Simple Network Time Protocol (SNTP)
Verify that the system date and time are accurate because it affects these
system features:
■
The 3Com telephone display panel
■
Business hours behavior
■
Time-dependent prompts in the Auto Attendant
■
Time and date stamp on voice mail
To access the date and time settings in the NBX NetSet utility:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Date and Time.
3 See the online Help for the procedure to set the system date and time.
If you enter the system time and select a new time zone simultaneously,
(that is, you do not apply the system time first) the system automatically
adjusts the system time you entered to correspond to the selected time
zone. For example, if the system time is set to 6:00 AM US Pacific, select
the US Pacific time zone and allow the system to adjust the time
automatically. If you enter 6:00 AM and then select the US Pacific time
zone, the system adjusts the system time based on 6:00 AM and displays
the system time as 3:00 AM US Pacific.
34
CHAPTER 2: SYSTEM SETTINGS
Simple Network Time
Protocol (SNTP)
The Simple Network Time Protocol (SNTP) synchronizes CPU clocks across
the Internet. SNTP belongs to the TCP/IP suite and works at the
Application layer in the OSI model, and uses UDP port 123 for
communication. SNTP Version 4 can operate in either unicast (point to
point), multicast (point to multipoint), or any cast (multipoint to point).
If you need to coordinate your system time with other Internet devices,
use the NBX NetSet utility to synchronize the system to an SNTP server at
a specified interval.
The initialization process initializes the SNTP client and connects to an
available SNTP server. The SNTP server provides the time, which the
system uses. When the synchronization interval expires, the system
synchronizes with the SNTP server again. Any changes to the SNTP
configuration take effect when the synchronization interval expires.
The system uses the time provided by the SNTP server for all references to
local time. This includes the time stamps used by the Call Processor,
phones, and gateways.
If the SNTP server fails, you can configure the system to transfer server
control to another active SNTP server in the list. (You have the option to
identify up to three SNTP servers to the system).
See the online Help for information about the procedure to configure the
system to use SNTP.
IP Settings
The IP Settings window allows you to define the network protocol
settings for this system and, if you are using IP On-The-Fly, to define the
range of IP addresses that the system can use to assign addresses to
devices as needed.
Before you configure the IP settings, you must have all necessary network
information, such as the network protocol, VLANs, Layer 3 IP information
about this Call Processor, and any DNS server addresses. This information
is propagated in the IP Settings window.
The IP Address Ranges window allows you to add or delete a range of IP
On-the-Fly addresses.
Audio Settings
Audio Settings enable you to affect the network impact of your audio
packets by enabling or disabling compression and silence suppression.
Audio Settings
35
You can enable and disable these settings for the entire system and then
override the system-wide setting for individual devices.
Compression
Overview
Before voice traffic can be transmitted over a digital network, the audio
waveform, an analog signal, must be encoded into a digital format. The
digitized audio is packetized and delivered over the network to a
destination, and then decoded back into a voice waveform. Software
called a codec (coder/decoder) converts the audio information between
digital and analog formats.
Digitized audio formats have different properties. Each format represents
a compromise between bandwidth and audio quality, that is, high quality
audio typically requires more network bandwidth. Compressing the
digitized audio data can conserve bandwidth with little compromise in
audio quality, but compression requires increased processing overhead
when encoding and decoding the audio information. Too much
processing overhead can introduce delay.
Table 7 lists the codecs that the system supports and describes the
characteristics of each one.
.
Table 7 Supported Codecs
Codec
Description
G.711
An International Telecommunications Union (ITU) standard for
audio encoding. Encoding and decoding is fast and support is
No Compression
widespread. Also called MULAW or µLAW. A-law is a slight
variation, which European telephone systems use. G.711
provides high quality audio at 64 Kbps. Telephone companies
worldwide use G.711 encoding to provide “toll-quality audio.”
ADPCM
Medium
Compression
G.729
High
Compression
Adaptive Differential Pulse Code Modulation (ADPCM) provides
good quality audio at a lower bitrate (32 Kbps) than G.711. The
system uses the International Multimedia Association (IMA)
version of ADPCM.
G.729, an ITU standard, employs a more sophisticated
compression technique than ADPCM and it is supported
worldwide. The G.729A codec compresses the audio information
to 8 Kbps, although processing overhead results in actual
bandwidths greater than 8 Kbps.
36
CHAPTER 2: SYSTEM SETTINGS
Table 7 Supported Codecs
Codec
Description
G.722
G.722.2
G.722.2LB
G.722.2 is an ITU-T standard for wideband voice applications and
services. G.722.2 is an adaptive multi-rate wideband codec that
uses bit rates ranging from 6.6 to 23.85 Kbps.
Wideband Audio G.722 is an SB-ADPCM (sub band Adaptive Pulse Code
Modulation) codec. It runs ADPCM on both the low band (0 4000 Hz) and the high band (4000 - 8000). The raw bit rate
(without network packet headers) is 64 Kbps.
G.722.2 is a CELP (code excited linear prediction) based codec.
G.722 is a 23.85 Kbps rate. G.722.2 LB has a rate of 8.85 Kbps.
The standard was originally designed for wireless networks and
the different rates allow for adapting to varying channel
conditions.
Codec Selection
It is important to remember not to select a codec based on compression
alone. Consider the trade-off between audio quality and bandwidth use.
System-Wide Audio
For system-wide audio, base the default list order on audio quality:
Table 8 Default Order List Based on Audio Quality
Codec
Quality
Bandwidth
G.722.2
best quality
medium bandwidth
G.722
high quality
high bandwidth
G.711
good quality
high bandwidth
G.722.2LB
good quality
low bandwidth
G.729
medium quality
low bandwidth
ADPCM
low quality
medium bandwidth
VTL Calls Audio
For Virtual Tie Line (VTL) audio, base the default list order on bandwidth
usage:
Table 9 Default Order List Based on Bandwidth Usage
Codec
Quality
Bandwidth
G.722.2LB
good quality
low bandwidth
G.729
medium quality
low bandwidth
Audio Settings
37
Table 9 Default Order List Based on Bandwidth Usage
Codec
Quality
Bandwidth
G.722.2
best quality
medium bandwidth
ADPCM
low quality
medium bandwidth
G.722
high quality
high bandwidth
G.711
good quality
high bandwidth
Custom Audio
For custom audio that you define based on the needs of your site, you
can choose the list order:
Table 10 Default Order List Based on Bandwidth
Codec
Quality
Bandwidth
G.729
medium quality
low bandwidth
G.722.2
best quality
medium bandwidth
ADPCM
low quality
medium bandwidth
G.722.2LB
good quality
low bandwidth
G.722
high quality
high bandwidth
G.711
good quality
high bandwidth
For the audio settings that are configured on each device, 3Com provides
sorted lists such as these. Each list contains the codecs supported for that
device only.
For example, a default codec configuration list for a 3Com Business
Telephone (that is, sorted by audio quality) may show a codec
configuration list like the following:
G711
good Q
high BW
ADPCM
low Q
med BW
If you have set device options for a low bandwidth connection, then the
3Com Business Telephone codec configuration list may show:
ADPCM
low Q
med BW
G711
good Q
high BW
38
CHAPTER 2: SYSTEM SETTINGS
When the system negotiates which codec to choose, the process starts
from the top of the list and queries devices to discover if they support the
codec. If the device is supported, the system chooses the codec;
otherwise, the system goes on to the next codec in the list and initiates
the query process.
Codecs and NBX
Devices
Codecs reside on the NBX devices — telephones, analog terminal
adapters, and so forth. Some older devices do not support the latest
codecs. Therefore, during call setup, NBX devices negotiate an encoding
scheme that both devices (or all devices on a conference call) support.
Table 11 lists each device that must encode or decode audio, and shows
how each device supports the available codecs. Certain devices are
marked “N/A” for the G.722 codecs because those codecs are for
wideband audio, which is not supported by wide area networks or across
the PSTN.
Table 11 Audio Encoding Supported by NBX Devices
Device
Part Number
3Com 1102, 2102, and 2102-IR
Business Telephones
G.729
ADPCM G.711
G.722
G.722.2 G.722.2LB
3C10121 3C10122 No
3C10226A
3C10228IRA
Yes
Yes
No
No
No
3C10226PE
3C10226B
3C10228IRPE
3C10228IRB
3C10281PE
3C10281B
Yes
Yes
Yes
No
No
No
3Com 2101 Basic Telephones
3C10248PE
3C10248B
Yes
Yes
Yes
No
No
No
3Com 3100 Entry Telephone
3C10399A
Yes
Yes
Yes
No
No
No
3Com 3101, and 3101SP Basic
Telephones
3C10401A
3C10401SPKRA
Yes
Yes
Yes
No
No
No
3Com 3101B Basic Telephone
3C10401B
Yes
Yes
Yes
Yes
Yes
Yes
3Com 3101SPB Basic Telephone
3C10401SPKRB
Yes
Yes
Yes
Yes
Yes
Yes
3Com 3102 Business Telephone
3C10402A
Yes
Yes
Yes
No
No
No
3Com 3102B Business Telephone 3C10402B
Yes
Yes
Yes
Yes
Yes
Yes
3Com 3103 Manager’s
Telephone
3C10403A
Yes
Yes
Yes
Yes
Yes
Yes
3Com 3106C and 3107C
Cordless Telephones
3C10406C
3C10407C
Yes
Yes
Yes
No
No
No
Audio Settings
39
Table 11 Audio Encoding Supported by NBX Devices (continued)
Device
Part Number
G.729
ADPCM G.711
G.722
G.722.2 G.722.2LB
3Com 3108 Wireless Telephone
3C10408A
Yes
Yes
Yes
No
No
No
Analog Terminal Adapter
3C10120
3C10120B
No
Yes
Yes
N/A
N/A
N/A
3C10400
Yes
Yes
Yes
N/A
N/A
N/A
3C10117
3C10117B-INT
No
Yes
Yes
N/A
N/A
N/A
3C10117C
Yes
Yes
Yes
N/A
N/A
N/A
3C10114
3C10114-ANZ
No
Yes
Yes
N/A
N/A
N/A
3C10114C
Yes
Yes
Yes
N/A
N/A
N/A
3C10116,
No
3C10116B
3C10116C
3C10164-ST (BRI)
3C10164C-ST (BRI)
3C10165
3C10165C
Yes
Yes
N/A
N/A
N/A
3C10116D
3C10165D
Yes
Yes
N/A
N/A
N/A
Analog Terminal Card
Analog Line Card
Digital Line Card
Silence Suppression
Overview
Yes
Silence suppression is a method of reducing the number of packets
transmitted during a conversation. Silence suppression can help you avoid
dropped packets on a congested network. During a conversation there
are periods of silence. A packet of silence takes up as much bandwidth as
a packet with audio data. If you enable Silence Suppression, the
telephone sends a silence indicator when it senses the start of a silent
period and it suppresses all subsequent voiceless frames. When another
NBX device receives this indicator, it generates and inserts white noise
until it receives the next frame that contains audio data. If you enable
Silence Suppression, a careful listener may notice a difference in audio
quality. The background white noise generated by the receiving
telephone is subtly different from the silence in an audio stream.
Silence suppression results in compromises to audio quality. Do not
enable suppression unless you are trying to solve network bandwidth
congestion issues that you cannot solve through other means, such as
increasing network capacity.
To enable Silence Suppression, click System-Wide Settings > Audio
Settings.
40
CHAPTER 2: SYSTEM SETTINGS
Timers
System timers enable you to set time-out periods for the system features
that are described in Table 12.
To set timers:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Timers.
Table 12 System Timers
Field
Purpose
Forward Voice
Mail On
Timeout
When a telephone’s Forward to Mail feature is enabled, sets the
duration of ringing before the system forwards a call to voice mail.
Forward Voice
Mail Off
Timeout
NOTE: If you set this time to be less than six seconds, Caller ID
information is not captured in voice mail.
When a telephone’s Forward to Mail feature is disabled, sets the
duration of ringing before the system forwards a call to voice mail.
The system uses this setting as the default for each new telephone
user that you add to the system. If you modify this value, users
added after the change use the new value as the default.
Telephone users added prior to the change are unaffected.
Individual telephone users can modify the default setting in the Call
Forward window of the User interface of the NBX NetSet utility by
specifying the number of times the telephone rings before the
system forwards a call.
Line Port Hold
Timeout
For a call that originated on an outside line, the length of time that
the call remains on hold before it rings at the extension that placed
the call on hold.
Call Park
Timeout
The length of time that a call can be parked before it rings at the
extension that parked the call.
Conference
Timeout
The length of time before the system abandons a conference
attempt. Applies to a blind conference only. The timeout takes
effect under these conditions:
■
Two people, A and B, are involved in a call and one of them
attempts to blind conference another person, C.
■
C does not answer and C’s voice mail does not pick up the call.
After the Conference Timeout period, the system stops ringing C’s
telephone, stops attempting to conference with C, and reverts to
the call between A and B.
Transfer
Timeout
The length of time that a transferred call attempts the transfer
before it rings at the extension that transferred the call.
Multicast Addresses
41
Table 12 System Timers
Field
Purpose
TAPI Line
Redirect
Timeout
The length of time before a call redirected from a TAPI route point
by an external application returns to its original destination. After
two failures, the call goes to the TAPI route point’s call coverage
option.
TAPI Line Redirect allows an external TAPI application, typically a
call center application, to reroute incoming calls based on caller ID
information automatically.
For more information, see TAPI Route Points.
Camp On
Timeout
The length of time that a call can camp on a busy extension before
the system returns the call to the extension that initiated the Camp
On feature.
The Camp On Timer can be set in increments of 10 seconds. The
default value for Camp On Timer is 180 seconds. The maximum
value that you can set the timer for is 600 seconds.
Automatic
Callback
Timeout
Multicast Addresses
The length of time that a call can be designated for call back
before the system cancels the call.
The Callback Timer has default value of 12 hours. You can set the
timer to have a null value. If Automatic Callback is not returned in
the specified time, Automatic Callback is cancelled. A system
reboot also cancels the Automatic Callback on an extension.
The system uses IP multicast addressing to distribute information for
these system features, which are available on Layer 2 and Layer 3 IP
devices:
■
Mapped line appearances
■
Internal pages
■
External pages
■
Conference calls
The Music on Hold (MOH) feature is available on Layer 2 devices only. The
IP implementation uses Internet Group Management Protocol (IGMP)
to transmit and distribute the necessary data and audio.
If you configure your system to use IP On-the-Fly or Standard IP and your
switches use IGMP Snooping, you must have an IGMP Host on the
network. Typically, an IGMP Host is an IP Multicast Router or a switch that
has IGMP Query capability.
42
CHAPTER 2: SYSTEM SETTINGS
The system IGMP is an implementation of administratively scoped
IP multicast that uses three scopes of administration:
■
Local scope — Limited by local routers with IP addresses 239.255.0.0
through 239.255.0.16
■
Organizational local scope — Limited by boundary routers with
IP addresses 239.192.0.0 through 239.192.0.14
■
Global scope — IP addresses 224.2.0.0 through 224.2.127.253
IGMP may not be available in all systems or network topologies. All
routers between the various components must support IGMP and the
necessary router protocols to establish a path for the IP multicast packets.
Each event that occurs in an IGMP setup, such as taking a telephone off
the hook, causes a packet of 200 Kb to 300 Kb to be sent.
The default settings for the IP multicast addresses function in most
network environments. Certain addresses are reserved.
The MAC address and the IP address displayed on any one line of the
Multicast Address List window are not related.
There are two methods for selecting multicast addresses:
■
Change IP — Lets you select a starting address for all entries.
Changing IP multicast addresses is a quick way to change the range of
system multicast addresses to avoid conflicts with other equipment on
your network.
■
Change bins — Lets you change a single entry by selecting from a list
of available bins. Changing IP bins is useful for changing a single
address that may conflict with another system device. Consult your
network administrator to find out which address is in conflict and the
new address to choose.
To change multicast addresses:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Multicast Addresses.
3 See the online Help for more information.
3
FEATURE SETTINGS
This chapter provides information about configuring the system to take
advantage of system features. It describes these topics:
■
Account Codes
■
Call Pickup
■
Call Park
■
Page Zones
■
Ring Patterns
■
Supervisory Monitoring
■
Speed Dials
■
WhisperPage
For more information about these topics and configuration procedures,
see the online Help.
Account Codes
Account codes are additional numbers that telephone users dial to
associate calls with specific functions, sources, or destinations. For
example, call center operations often employ account codes to associate
calls made by Automatic Call Distribution (ACD) agents with their
relevant accounts for tracking purposes. (See Chapter 7 in this guide for
more information about ACD.) Telephone users enter an account code
while placing a call or during a call.
Verifying account codes is a global configuration setting, while enforcing
account codes is by means of a Class of Service (CoS) setting. If the CoS
setting enforces the account code for that particular type of call, a
telephone user must enter an account code before the system routes the
call.
44
CHAPTER 3: FEATURE SETTINGS
The enforced account code does not apply to internal or emergency (911)
calls.
Account codes range from two to sixteen digits. The system allows up to
5000 account codes.
The system maintains a centralized list of account codes that you can
update, and can verify the account codes that telephone users enter
against this list of account codes.
Account codes are classified by four operation modes, which define how
strictly to enforce account code usage for outgoing calls based on Class
of Service criteria. See the Account Codes: Operational Modes section of
this chapter for information about operational modes.
Feature Interaction
This section describes the ways in which account codes interact with
other features.
Bridged Station Appearance
Only a primary telephone can originate a call. However, once the call is
answered, either the primary or the secondary telephone can place the
call on hold and take it off hold. The last account code that the primary or
the secondary telephone entered overrides the account code for the call.
CO Flash
The system does not enforce account code entry for calls that you
originate by means of a CO Flash. This means that you can receive a call,
perform a CO Flash, and make an external call without entering an
account code.
Conference
During the time that forced account code mode is enabled, you must
enter an account code for each leg of a conference. The account code
applies to the call leg, and not to the call from which the conference is
initiated. After the conference is completed, an account code entered by
any telephone user overrides the account code for the conference call.
Emergency Numbers
The system allows emergency numbers without an account code.
Account Codes
45
Call Forwarding
You cannot specify account codes as part of a forwarding number. If you
forward a call while forced account code entry is enabled, the call is
forwarded and you are not prompted to enter an account code. A side
effect of this feature interaction is that an internal extension could be
used to forward calls to an external number and thereby circumvent
forced account code entry.
International Dialing
If you enabled Force mode and a timeout occurs after you have entered
the minimum number of digits and are still dialing, the system prompts
you to enter an account code. After you enter the account code, you can
continue entering digits for the international number.
Paging
You can use Paging without entering an account code.
Call Park
If you entered an account code before you park a call, that call is
preserved when you unpark it. You can unpark calls without entering an
account code. You can enter a new account code after unparking the
call.
Redial
Account codes are not stored as part of the redial digits (except on analog
phones), even if you specified the account code as part of a speed dial
operation. If outbound digits are redialed while forced account code
mode is enabled, the system prompts you to enter an account code.
Speed Dial
Phones with programmable buttons and Attendant Consoles can use
speed dial with account codes. From the User interface of the NBX NetSet
utility:
■
Configure a one-touch speed dial with an account code. Click
Directory and then the One-Touch Speed Dial tab. Use the following
format in the Number field:
[888] + Account code + # + Outbound number
46
CHAPTER 3: FEATURE SETTINGS
You must use brackets, which indicates that 888 is a feature code.
■
Configure a personal speed dial with an account code. Click Directory
and then the Personal Speed Dial tab. Supply the account code
separately in the Account Code field.
For security reasons, the telephone’s display panel does not display the
account code during a speed dial. If the account code is valid, the display
panel displays the account name.
Call Transfer
If you enable Forced mode, when you transfer a call, enter an account
code before the second call is routed. After the transfer is complete, the
account code entered on the second call leg also applies to the
transferred call.
This means that the first call (prior to the start of transfer) can have
account code XXX, the second call (prior to the completion of the
transfer) can have account code YYY, and the transferred call has account
code YYY.
VTL
Forced account code entry applies to all VTL calls.
Account Codes:
Operational Modes
Before you configure account codes for your system, be sure that you are
familiar with the enforcement and verification mechanisms and how they
affect your call operations.
Codes are classified by one of the these modes:
■
Forced / Verified Mode
■
Forced / Unverified Mode
■
Unforced / Verified Mode
■
Unforced / Unverified Mode
Forced / Verified Mode
In Forced / Verified mode, the system first forces the telephone user to
enter an account code and verifies that the code is correct before routing
an outgoing call. The system verifies the account code against a master
list that you establish.
Account Codes
47
To place an outgoing call, dial the outbound number in either of the
following ways:
■
Outbound number + # + Account code + #
■
Feature + 888 + Account Code + # + Outbound number
In the first instance, you may not know or remember that an account
code is necessary and dial only the outbound number. In this case, the
telephone prompts you to enter an account code after a short period of
time.
If the account code is valid, the Feature Success tone plays and the system
routes the call.
If the account code is invalid:
■
On a telephone with a display panel, the display panel displays the
invalid account code and prompts you to enter the account code
again. After three unsuccessful attempts to enter the account code,
you must start over by reentering the outbound number and account
code.
■
On a phone without a display panel, the telephone plays the Feature
Error tone and you must reenter the entire digit sequence.
The system does not require account codes for emergency calls, such as
911, and immediately routes the calls.
During the call, you can enter another valid account code using the
following format:
F+ 888 + Account_code + #
You can enter multiple account codes during a call; the most recently
entered account code overrides the previously entered account code. In
Verified account code mode, the newest account code only overrides the
existing account code if it has been verified.
The account code and account name information is available in the Call
Detail Reporting (CDR) data. To download the NBX Call Reports software,
click Download > Applications. To enable CDR, click System Maintenance
> Call Report Settings.
Enforcing account codes is applicable for outgoing external calls only.
48
CHAPTER 3: FEATURE SETTINGS
Forced / Unverified Mode
Forced / Unverified mode is similar to Forced / Verified mode in that the
system forces you to enter an account code. However, because the
system does not verify the account code, the telephone either:
■
Displays the account name associated with the code.
■
Displays the text string Unknown Account.
In this mode, it is possible for you to enter an invalid account code and
still proceed with the call.
The account code and account name information is available in CDR.
The system only forces the use of account codes on outgoing, external
calls.
Unforced / Verified Mode
In Unforced / Verified mode, the system does not force you to enter an
account code. However, if you do enter an account code, the system
verifies that the account code is correct.
You can enter an account code during the call using the following
format:
Feature + 888 + Account_code + #
The system verifies the account code against the list of valid account
codes.
■
On a telephone with a display panel, an invalid account code shows
the text string Unknown Account, and the call continues.
■
On a telephone without a display panel, an invalid account code plays
the Feature Error tone, and the call continues.
Unforced / Unverified Mode
Unforced / Unverified mode is similar to Unforced / Verified mode, but the
system does not verify the account code. The telephone displays the
account name if the account code is valid and the call continues.
The account code and account name information is available in CDR.
Call Pickup
49
Configuring Enforcement and Verification
To enable or disable verification of outgoing calls:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Go to Feature Settings > Account Codes.
3 Enable the check box next to an account code (or create a new one
before proceeding).
4 Enable or disable the Enforce account codes verification check box, as
necessary.
5 Click Apply.
To enforce or relax the need for an account code:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click User Configuration > Class of Service.
3 Click a CoS Group name, which displays the Modify window.
4 Locate the Class of Service (such as International or Long Distance), and
then enable or disable the corresponding Force Acct Code check box.
5 Repeat the previous step for each Class of Service.
6 Click Apply to activate the changes and leave this window open, or click
OK to activate the changes and close this window.
Call Pickup
Call Pickup allows telephone users who hear a telephone ringing to
answer the call on their own telephones. To enable this feature, you add
telephone extensions to Call Pickup Groups.
The Call Pickup feature is not supported for hunt groups. However, it is
supported for ACD groups.
Group Numbers
Table 13 summarizes the Call Pickup group numbers.
50
CHAPTER 3: FEATURE SETTINGS
Table 13 Call Pickup Group Numbers
System
Group Numbers
V3000, V3001, V3001R,
V5000
50 Call Pickup groups:
■
Group 0 through group 31 (extension 500 through
531)
■
Group 32 through group 49 (extension 482 through
499)
50 Directed Call Pickup groups (extension 540 through
589)
NBX 100
32 Call Pickup groups from group 0 (extension 500)
through group 31 (extension 531)
10 Directed Call Pickup groups from 540 through 549
See an NBX telephone guide for user instructions about how to use Call
Pickup.
If you select Auto Add Phones to Call Pickup Group 0 (System-Wide
Settings > Auto Discovery), every telephone that you add to the system is
a member of Call Pickup group 0 (extension 500). Any telephone can pick
up calls to a telephone user who is a member of default Call Pickup
Group 0. Telephone users can add or remove their own telephone
extensions from the group to allow or prevent others from picking up
their calls. See the NBX Telephone Guide and the User online Help for
more information.
You can add telephone users to and remove them from any of the
groups. Telephone users can remove themselves from Call Pickup group
0, but not from any other Call Pickup groups.
You can map Call Pickup Groups to user telephone buttons to provide
one-touch access to the Call Pickup groups. See “Creating and Managing
Button Mappings” in Chapter 5.
To configure call pickup groups and modify group membership:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Feature Settings > Call Pickup.
3 See the online Help for more information.
Call Park
Call Park
51
When you park a call, anyone can retrieve it from any other telephone in
the system by entering the Call Park extension that is associated with that
call.
Example: You need to transfer an incoming call, but the person that you
need to reach is not available. You can park the call on any unused Call
Park extension, and then page the person and announce that Call Park
extension. The person can then dial the Call Park extension from any
internal telephone to retrieve the parked call.
These are the default system configuration extensions for Call Park:
Adding a Call Park
Extension
■
4-digit dial plan: 6000 through 6099
■
3-digit dial plan: 601 through 609
To add a Call Park extension:
1 Click Feature Settings > Call Park.
2 Click Add.
3 Enter the number of an extension in the Extension field.
4 Enter a name for the extension in the Name field.
5 Click OK.
Changing a Call Park
Extension Name
To change the name of a default Call Park extension:
1 Click Feature Settings > Call Park.
2 Click an extension.
3 Enter the new name for the Call Park extension in the Name field.
4 Click OK.
Removing a Call Park
Extension
You can remove a Call Park extension at any time:
1 Click Feature Settings > Call Park.
2 Select the extension, or extensions, that you want to delete and click
Remove Selected. To select all extensions, enable the Select check box.
3 Click OK.
52
CHAPTER 3: FEATURE SETTINGS
To replace any extension that you remove, see “Adding a Call Park
Extension” on page 51.
Page Zones
The Page Zone feature allows you to designate a subset of devices within
the system as members of a zone. Telephone users then can page
members of that group only, rather than paging all devices on the system.
The system supports up to 16 page zones for each system.
The system allows multiple simultaneous zone pages. However, a device
that is currently paging or being paged will not respond to another page
request.
A Page Zone extension must be in the external device extension range:
■
6000-7999 for a 4-digit dial plan
■
600-799 for a 3-digit dial plan
The default 3- and 4-digit dial plans assign extension numbers that start
with 7 as diagnostic. Diagnostics is a Class of Service that you can assign
to a telephone user. For example, if you want to assign a page zone to
extension 720, either change the dial plan (to make 7** an internal call)
or assign the CoS permissions labelled Diagnostics to users who will be
dialing the 720 page zone. To keep the dial plan and CoS defaults, use
the extension range of 6000 – 6999 (or 600 – 699) for page zones.
Many extensions in these ranges are already reserved for Call Park and
other features. Typically, you choose an extension near the upper end of
the external extension range. Click Reports > Device List for a list of
extensions currently in use.
Page Zone Feature
Support
The Page Zone feature supports the following features and desktop
applications:
■
Caller ID — The display panel on the device originating the zone page
displays the zone page’s name and extension; the recipients’ display
panels do not display the broadcaster’s extension.
■
Hands Free — A zone page reaches a device that has Hands Free
enabled.
■
Hold — A zone page reaches a device that has Hold enabled.
Ring Patterns
53
■
Speed Dial (Personal) — A device is able to store personal speed dial
extensions as zone page extensions.
■
Speed Dial (System) — A device is able to store system speed dial
extensions as zone page extensions.
All other features and desktop applications are not supported. A zone
page does not reach a device that has Do Not Disturb enabled.
When zone paging, you cannot include devices from a different Call
Processor in a local page zone. However, if your dial plan is configured to
support Virtual Tie Lines (VTLs), you can include an extension on a
different Call Processor in a zone page.
SIP telephones can neither initiate nor receive pages.
To configure Page Zones:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Feature Settings > Page Zones.
3 See the online Help for information about how to add, modify, and
remove page zones.
Ring Patterns
You can set system-wide ring patterns, such as one, two, or three rings,
to distinguish between internal and external calls.
Do not confuse ring patterns with ringer tones, which telephone users
can set for their telephones from the NBX NetSet utility. For information
about setting a telephone user’s ringer tones, see an NBX telephone
guide or the User online Help.
To set ring patterns:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Feature Settings > Ring Patterns.
3 See the online Help for more information.
Supervisory
Monitoring
Supervisory Monitoring allows a supervisor to monitor calls on the
system, with or without the knowledge of the parties engaged on the
54
CHAPTER 3: FEATURE SETTINGS
call, as a part of the quality control operations of a site. Typically, you
monitor or audit calls that are routed through ACDs, Hunt Groups, or
TAPI Route Points. However, you can monitor any call.
This section describes these topics:
Introduction to
Monitoring
■
Introduction to Monitoring
■
Domains and Privacy
■
Announcement Tones and Supervisory Modes
Supervisory Monitoring takes place through domains. A domain is a
collection of telephone users who are grouped because they are logically
related in some way. In this case, the telephone users in a domain are
candidates for monitoring. If you enable Supervisory Monitoring in a
domain, each telephone user in that domain can be monitored.
By default, Supervisory Monitoring is disabled. You can enable or disable
Supervisory Monitoring on a system-wide basis. Click System-Wide
Settings > Enable Features System-Wide and then enable the Supervisory
Monitoring check box.
There may be situations in which a telephone user’s calls need not be
monitored. In this case, the Privacy List domain is a special domain that
contains telephone users whose calls cannot be monitored.
A monitoring session, in which an agent’s call is actively monitored,
includes:
■
The supervisor, or monitoring party, who is any telephone user in the
system who knows the Supervisory Monitoring domain password and
thus can monitor the members of the domain associated with that
password.
■
The agent, who is any telephone user who is part of a supervisory
monitoring domain and who a supervisor in that domain can monitor,
unless that telephone user is in the Privacy List domain.
The actual audio state, or mode, of the session may be one of the
following:
Supervisory Monitoring
55
Table 14 Supervisory Monitoring Modes
Mode
Description
Monitor
Enables a supervisor to monitor a call with or without the
knowledge of the agent or the external party (typically a
customer).
Whisper
Enables a supervisor to coach or speak with an agent without
the customer's knowledge.
Barge-In
Enables the supervisor to speak with both the agent and the
customer.
You can configure announcement tones to allow the agent or the
customer, or both, to know that the call is being monitored.
Domains and
Upgrades
Supervisory Monitoring domains are a new feature in release R6.x. To
create and manage Supervisory Monitoring domains, click Feature
Settings > Supervisory Monitoring and see the online Help for more
information.
Release R5.0 supported Supervisory Monitoring for calls that hunt
groups, ACD groups, and route points managed. When you upgrade a
release R5.0 system to release R6.x, the system creates new Supervisory
Monitoring domains automatically for all existing groups for which the
Supervisory Monitoring passwords were changed from the default
setting. If a group’s default password was not changed in release R5.0,
the system does not create a new Supervisory Domain for that group.
The new Supervisory Monitoring domains have these characteristics:
■
The upgrade process transfers all relevant information from release
R5.0 groups to the new release R6.0 Supervisory Monitoring domains.
For example, the members of a new Supervisory Monitoring domain
are the same members of the Hunt Group or the ACD Group that you
created in release R5.0.
■
The name of each new Supervisory Monitoring domain that the
system creates during the upgrade process is the group name plus the
group number of the Hunt Group or the ACD Group that had
Supervisory Monitoring enabled. The new password is the group’s
extension plus the former supervisory monitoring password. For
example, if ACD Group 4000 had password 1234 in release R5.0, the
new Supervisory Monitoring domain password in release R6.x is
40001234.
56
CHAPTER 3: FEATURE SETTINGS
Domains and Privacy
■
The tones that are enabled for a new Supervisory Monitoring domain
are the same tones that were in effect for the Hunt Group or ACD
Group before the upgrade.
■
The call type settings default to incoming group calls only.
Be aware of the following privacy issues when you use Supervisory
Monitoring on your system:
■
Monitoring Ability
A supervisor can monitor:
■
■
■
■
All call types, which includes incoming, outgoing, and non-ACD
calls.
Anyone in the system.
Three-party conference calls. The supervisor counts as one of the
parties in a conference, which supports up to four parties at one
time.
Domains
A domain defines logical groupings of the agents who a supervisor, or
supervisors, is required to monitor.
The NBX 100 system can support up to 49 domains. All other
hardware platforms can support up to 101 domains.
Anyone who has a valid Supervisory Monitoring domain password can
be the supervisor and monitor domain members.
Prior to release R6.0, the supervisor had to enter the extension and
password of the last hunt group, ACD, or route point that the incoming
call traversed to monitor a call. This restriction is removed.
Be sure to create Supervisory Monitoring domains that specify the
following information for the system:
■
■
■
The Supervisory Monitoring domain's unique name and password
The types of calls that the supervisor can monitor (Incoming Group
Only calls or All calls)
The calling groups (ACD, Hunt Group, or TAPI Route Point) that the
supervisor can monitor
■
The agents or telephone users than the supervisor can monitor
■
Announcement tones for Monitor, Whisper, and Barge-In modes
Supervisory Monitoring
■
57
Privacy List
The Privacy List, which is a reserved system domain, specifies those
telephone users whom a supervisor cannot monitor. The Privacy List is
unlike other Supervisory Monitoring domains:
■
■
■
■
■
You cannot change the name of the Privacy List.
You can define only telephone users for the Privacy List. There are
no tone settings or call type settings for this domain.
You cannot add Hunt groups, ACDs, or TAPI Route Points as
members of the Privacy List.
You can add members of the Privacy List to individual domains,
even though these telephone users cannot be monitored. You can
track these cases using reports.
Call Privacy
Call Privacy allows a telephone user to prevent a call from being
monitored on a call-by-call basis. Telephone users can toggle Call
Privacy on and off to block or accept monitoring.
This contrasts with membership in the Privacy List domain, which
ensures that a supervisor cannot monitor any calls associated with a
telephone user.
You can assign a telephone user to a CoS group that allows Call
Privacy so that the telephone user can use Feature Code 428 to
prevent the supervisor from monitoring the current call as follows:
■
■
The telephone user can activate the Call Privacy feature before a
call (for example, by going off-hook and dialing Feature Code 428
and then dialing an internal or external call), or during a call (for
example, by dialing Feature Code 428 after answering an incoming
call). If the telephone user activates Call Privacy while on a call that
the supervisor is monitoring, the monitoring session ends.
When an active Call Privacy session ends, (that is, the telephone
user activates Call Privacy, initiates a call, and then exits the call) the
Call Privacy settings are no longer applicable and the next call is
open to monitoring.
You can map Feature Code 428 to one of the telephone system access
buttons.
58
CHAPTER 3: FEATURE SETTINGS
Announcement Tones
and Supervisory
Modes
This section describes information about the following topics:
■
Supervisory Monitoring Announcement Tones
■
Using Monitor Mode
■
Entering Whisper Mode From Monitor Mode
■
Entering Barge-In Mode From Monitor Mode
■
Changing Agents and Changing Modes While Monitoring
The Call Timer feature on the display panel of the telephone does not
work with Supervisory Monitoring. Also, to use Supervisory Monitoring,
you must use a telephone that has a display panel and Soft Keys.
Supervisory Monitoring Announcement Tones
Before you use Supervisory Monitoring, be sure that you are familiar with
the announcement tone scheme. The system uses the announcement
tones to indicate the status of Supervisory Monitoring to call participants.
■
When the supervisor invokes either Monitor or Whisper mode, the
agent may hear a tone, depending on how you configured the
Supervisory Monitoring domain to which that agent belongs.
■
When the supervisor invokes Barge-In mode, the agent and the
external party may hear a tone, depending on how you configured the
Supervisory Monitoring domain to which that agent belongs.
■
When the supervisor invokes Monitor mode, a tone plays when the
system prompts the supervisor to enter the agent's extension. You
cannot disable this tone.
■
Each of the three modes (Monitor, Whisper, and Barge-In) has a
unique announcement tone.
■
The tone accompanying the prompt for the agent's extension has the
same pitch as the announcement tone.
Default Tones
Table 15 lists the default settings for Supervisory Monitoring.
Table 15 Supervisory Monitoring Announcement Tone Settings (Default)
Mode
Default Setting
Monitor
Off
Whisper
Off
Supervisory Monitoring
59
Table 15 Supervisory Monitoring Announcement Tone Settings (Default)
Mode
Default Setting
Barge-In
On
Using Monitor Mode
The supervisor can use Feature Code 425 to invoke Monitor mode to
monitor a conversation in progress. You can map this feature code to a
button with or without a status light for individuals or groups. (Telephone
users can change the button mapping for their own extensions only.)
1 Verify that:
■
You have enabled Supervisory Monitoring.
■
You create a Supervisory Monitoring domain.
■
You know the Supervisory Monitoring domain password. A telephone
user who acts as the supervisor must know the Supervisory
Monitoring domain password.
■
The agent whom you want to monitor is a member of the Supervisory
Monitoring domain.
2 On the telephone, press the programmable access button mapped to
Monitor, or press the Feature button and use the keypad to enter Feature
Code 425 for Monitor.
The system prompts for the domain password.
3 Enter the Supervisory Monitoring Domain password, and then press
either the OK menu option or # key.
■
■
If the password or the extension is invalid, the display panel
displays an error message and allows you to reenter the password.
If the extension number is valid, the system plays a tone and
prompts for an agent extension.
4 Enter the extension of an agent who is a member of the Supervisory
Monitoring domain.
The system checks the state of the call that you are attempting to join
and uses the display panel to inform you about the call status:
■
If the agent is not on an call, the display panel displays IDLE and allows
you to enter another extension.
■
If the agent is not logged into the system, the display panel displays a
message to that effect, and allows you to take another action.
60
CHAPTER 3: FEATURE SETTINGS
■
If the agent is already being monitored, the display panel displays a
message to that effect, and allows you to take another action.
■
If the agent is free to be monitored, the conversation becomes
audible, and the system plays an announcement tone if it has been
configured to do so.
While you monitor a call, you can change the agent extension and the
supervisory monitoring mode.
5 To end the Monitor session, hang up the telephone receiver.
The supervisor’s display panel is the only display panel that displays menu
options or indications that the Supervisory Monitoring feature is in use.
(The agent’s display panel does indicate that Supervisory Monitoring is in
use.)
Changing Agents and Changing Modes While Monitoring
While you listen to a call in Monitor mode, the telephone display panel
provides options to allow you to choose Barge-In mode, Whisper mode,
or to change to another agent’s call.
The display panel displays the extension of the agent currently being
monitored, as well as these menu options:
■
Whisp
■
Chg
■
BrgIn
Entering Whisper Mode From Monitor Mode While in Monitor
mode, the supervisor can invoke Whisper mode.
The supervisor in Whisper mode can join, as well as listen to, the
conversation between the agent and the customer. For example, the
supervisor can provide information or a suggestion to the agent. The
agent hears the supervisor’s suggestions in addition to the conversation
with the customer. The customer can hear the agent only.
Supervisory Monitoring
61
To enter Whisper or Barge-In mode, you must first enter Monitor
mode, and then switch to the appropriate mode.
1 Press the Whisp Soft Key on your telephone.
The agent may hear an announcement tone depending on how you
configured Supervisory Monitoring.
2 Hang up the telephone receiver to end the Monitor session.
Entering Barge-In Mode From Monitor Mode
mode, the supervisor can invoke Barge-In mode.
While in Monitor
Barge-In mode immediately inserts the supervisor into the conversation
with the agent and the customer. The supervisor, agent, and customer
can hear and speak with the other parties in the conversation.
To enter Whisper or Barge-In mode, you must first enter Monitor
mode, and then switch to the appropriate mode.
1 Press the BrgIn Soft Key on your telephone.
The agent may hear an announcement tone, depending on the way you
configured Supervisory Monitoring.
2 Hang up the receiver to end the Monitor session.
Changing Agents While Monitoring a Conversation While in
Monitor mode, the supervisor can change which agent to monitor.
1 Press the Chg Soft Key on your telephone.
The system prompts for the agent extension and plays a tone.
2 Enter the new extension and press the OK menu option or # key.
The previous agent’s call is no longer audible to you and the current
agent’s call becomes audible. The current agent may hear an
announcement tone, depending on the way you configured Supervisory
Monitoring.
3 Hang up the receiver to end the Monitor session.
Supervisory
Monitoring Usage
Notes
This section describes general information about Supervisory Monitoring.
Topics include:
■
Special Considerations
■
Supervisory Monitoring Error Conditions
62
CHAPTER 3: FEATURE SETTINGS
Special Considerations
To configure Supervisory Monitoring, you must have Administrator access
rights to the system. If you are a call supervisor, note the following issues
when you monitor calls in progress:
■
You can monitor calls internal to the system or external calls.
■
You can monitor a call across a Virtual Tie Line (VTL).
■
Any one of the parties involved in a Supervisory Monitoring
environment (customer, agent, or supervisor) can put the call on hold
and answer another call.
■
You cannot invoke session-modifying services during a call being
monitored. You can invoke the following telephone features during a
call:
■
Forward voice mail
■
Do Not Disturb
■
Mute
■
Hold
The display panel displays the message Not allowed if you invoke any
other features during a monitoring session.
■
If the customer or the agent invokes a session-modifying service such
as Transfer, Conference, Call Park, or Transfer to Voice Mail, the
system drops the supervisor from the call.
■
You can use third-party TAPI applications to monitor calls.
■
You cannot monitor more than two calls at the same time. Of the two
calls, only one can be active at any given time; the other call must be
on hold.
■
You can monitor other supervisors. However, you cannot monitor a
supervisor who is monitoring another call.
■
Multiple supervisors can monitor different calls by the same agent.
However, a specific call can be monitored by one supervisor only at
any one time.
■
If you exit the monitoring session, the call between the customer and
the agent is unaffected.
■
You cannot invoke Supervisory Monitoring if the supervisor is already
on an active call.
Supervisory Monitoring
63
■
When you invoke Barge-in and either the caller or the agent
subsequently puts the call on hold, you are still able to talk to the
remaining party.
■
The telephone user does not need to be an agent to be in a monitored
call, nor does this user have to be logged in.
■
An agent in a monitored call can transfer a call to another party.
■
A primary telephone configured with bridged extensions could receive
a call that an associated secondary telephone, which is not a part of a
hunt group, ACD, or route point, can answer.
Restrictions in Monitoring ACD Calls There are a few cases in which
you cannot monitor an ACD call, though the system is processing the call
as an ACD call.
■
You cannot monitor ACD calls going through call coverage to voice
mail or Auto Attendant.
■
Multiple supervisors cannot monitor the same agent at the same time.
Supervisory Monitoring is limited to one active supervising session for
each agent.
Supervisory
Monitoring Error
Conditions
This section describes the most common Supervisory Monitoring errors
and the results that occur. If appropriate, the table lists corrective
measures that you may take to recover from errors.
■
Feature Interaction Errors
■
Validation Errors
■
Supervisory Monitoring Service Errors
■
Device Errors
Table 16 Feature Interaction Errors
Event
Action
A feature is active on the supervisor’s
phone that prevents Supervisory
Monitoring.
The display panel displays an explanatory
error message and the phone returns to
the Ready state.
The agent or the customer hangs up
The display panel cannot display
while the supervisor has the call on hold. messages while a call is on hold; the
supervisor’s phone immediately returns
to the Ready state.
64
CHAPTER 3: FEATURE SETTINGS
Table 16 Feature Interaction Errors
Event
Action
Supervisory Monitoring fails to start
because two Supervisory Monitoring
services are already active on the
supervisor’s device.
The display panel displays an explanatory
error message and the phone
immediately returns to the Ready state.
The agent or the customer invoke a
feature that cannot operate with
Supervisory Monitoring while the
supervisor is monitoring the call.
The display panel displays an explanatory
error message and the system gives the
supervisor the option to change agents.
A feature is active on the agent’s
telephone that prevents Supervisory
Monitoring from starting.
The display panel displays an explanatory
error message and the system gives the
supervisor the option to change agents.
An agent puts an ACD call on hold
The display panel displays an explanatory
before the supervisor invokes Supervisory error message and the system gives the
Monitoring.
supervisor the option to change agents.
Table 17 Validation Errors
Action
Result
The supervisor enters an incorrect
password or extension.
The display panel displays an explanatory
error message and the system gives the
supervisor the options to try again or
exit.
The supervisor enters an incorrect
password three times.
The display panel displays an explanatory
error message and the phone exits
Supervisory Monitoring and returns to
the Ready state.
The supervisor enters the extension of a
device that cannot be monitored (for
example, the extension is a paging, Call
Park, or Voice Mail extension).
The display panel displays an explanatory
error message for five seconds, and then
the system prompts again for the
extension of an agent.
Speed Dials
65
Table 18 Supervisory Monitoring Service Errors
Action
Result
Another supervisor is already monitoring The display panel displays an explanatory
the call.
error message for five seconds, and then
the system prompts again for the
extension of an agent.
The agent is not on any call.
The display panel displays an explanatory
error message for five seconds, and then
the system prompts again for the
extension of an agent.
The agent hangs up before the
The display panel displays an explanatory
monitoring message reaches him causing error message for five seconds, and then
Supervisory Monitoring to timeout.
the system prompts again for the
extension of an agent.
Table 19 Device Errors
Action
Result
The supervisor’s device does not support The display panel displays an explanatory
conferencing.
error message and the phone returns to
the Ready state.
Speed Dials
The monitored agent’s device does not
support conferencing.
The display panel displays an explanatory
error message and the system prompts
again for the extension of an agent.
The customer’s device does not support
conferencing.
The display panel displays an explanatory
error message and the system gives the
supervisor the option to change agents.
You can create up to 100 System Speed Dial numbers. You can also
create system speed dial and personal speed dial button definitions and
assign them to groups.
Do not confuse use speed dial codes with extension numbers.
Any telephone in a Telephone Group has access to the same button
definitions. Telephone users can create personal speed dial definitions for
buttons that do not already have a button mapping. Telephone users can
also change definitions for any buttons mapped as personal speed dial
buttons, even if those buttons are defined in the Group Button
Mappings.
66
CHAPTER 3: FEATURE SETTINGS
System speed dial numbers are not subject to Class of Service (CoS)
restrictions. Therefore, a speed dial number mapped to a number that is a
toll call is available to telephone users even if their CoS does not allow toll
calls. Personal speed dial numbers are subject to CoS.
To set up system speed dials:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Feature Settings > System Speed Dials.
3 See the online Help for information about how to configure system speed
dials.
WhisperPage
The WhisperPage feature allows you to dial an extension that is involved
in an active conversation with another person and speak to that person
without the other party on the call being able to hear you.
WhisperPage is typically used in the workplace by an assistant and
manager. While a manager is on a call, an assistant can start a
WhisperPage session to alert the manager of an important meeting or
call. During the WhisperPage session, the assistant cannot hear the
manager or the third party speaking and the third party cannot hear the
comments of the assistant.
If the manager is not on an active call when the assistant starts a
WhisperPage session, the system places the call as if the assistant dialed
the manager's extension.
A typical WhisperPage session occurs as follows:
1 An assistant initiates a WhisperPage through Feature Code 426 or a
programmed system access button, depending on the type of telephone
and how it is configured.
2 The manager may hear an alert tone announcing the WhisperPage
request.
The display panel on the manager's phone shows the Caller ID of the
assistant and the WhisperPage icon for 5 seconds, and then the display
reverts back to the Caller ID information of the person the manager is
speaking with.
WhisperPage
67
The manager also has a period of time, called the Decline Time, to refuse
the WhisperPage. You can configure WhisperPage behavior by enabling
or disabling the alert tone and specifying the Decline Time to be 0 – 9.9
seconds in 0.1 second intervals. The default Decline Time is two seconds.
You can also configure, on a per-user basis, the WhisperPage feature
success tone waiting time period that the assistant hears.
3 To accept the WhisperPage, the manager does nothing.
When the Decline Time period expires, the assistant hears a tone that
indicates that the WhisperPage session is active. The display panel on the
assistant's phone displays Whispering and the manager's extension to
indicate that the WhisperPage session is active. The assistant can speak to
the manager. The other party on the call does not hear the assistant's
comments and the assistant cannot hear the manager or the person to
whom the manager is speaking.
4 To refuse the WhisperPage, the manager can invoke the Do Not Disturb
(DND) feature during the Decline Time.
The assistant hears an error tone and the display panel on the assistant's
phone shows a message that indicates that the WhisperPage was
unsuccessful. The manager can also invoke DND to end an active
WhisperPage session. If the manager invokes DND, the feature is active
until the manager disables it.
5 The assistant hangs up to end the WhisperPage session.
You can configure the WhisperPage announcement tone that the
manager hears on a per-user basis:
1 Click Feature Settings > WhisperPage.
2 Click a domain and then click the extension of a member of that domain
The system displays the Report window.
3 Type a value in the Decline Time field.
4 Click OK.
However, you cannot configure the WhisperPage feature success tone
heard that the assistant hears.
You can map Feature Code 426 for WhisperPage to a telephone button
for individuals or groups. Telephone users may change the button
mapping for their extension only if you have extended this privilege using
68
CHAPTER 3: FEATURE SETTINGS
the CoS function. You can configure the mapped buttons from the
Button Mapping window. Click Telephone Configuration > Telephones or
Telephone Configuration > Telephone Groups. Click a telephone
extension or a telephone group name, depending on which sub menu
you chose, and then click the Button Mapping tab.
WhisperPage
Permissions
Both the manager and the assistant in a WhisperPage session must be
assigned to a WhisperPage domain and have appropriate WhisperPage
access privileges.
Telephone users can view their WhisperPage access privileges from within
the NBX NetSet utility. WhisperPage permissions include this information:
■
Whether or not the WhisperPage alert tone is enabled
■
The waiting time before an initiated WhisperPage session becomes
active
■
Telephone users (listeners) to whom you can initiate a WhisperPage
session
■
Telephone users (speakers) who can initiate a WhisperPage session
with you
You can define these access privileges when you create the WhisperPage
domains.
Using Domains For
WhisperPage
A domain is a grouping of telephone users who are logically associated in
some way. You create domains for use with the WhisperPage feature.
Each domain must have a unique name, which you configure in the NBX
NetSet utility (click Feature Settings > WhisperPage).
For each domain in the system, configure the following:
■
The list of members in that domain to whom speakers can whisper.
■
A list of members in that domain who can invoke the WhisperPage
feature.
You can create a domain with no members. There can be a maximum of
50 domains in the system. (Some platforms may support fewer domains
because of resource usage.)
WhisperPage
69
The Report window shows the extensions to which a telephone user can
whisper, and also shows the extensions that are able to whisper to the
telephone user.
1 Click Feature Settings > WhisperPage.
2 Click a domain.
3 Click the extension of a member of that domain to display the Report
window.
Feature Interaction
With Whisper Page
This section describes how the WhisperPage feature interacts with other
system features.
Feature
Manager
Assistant
Account Code
Allow
Disallow
CO Flash
Allow
Disallow
Conference
Allow - drop assistant
Disallow
Conference drop
Allow
Disallow
COS Override
Allow
Disallow
Directory
Allow
Disallow
Direct Mail Transfer
Allow - drop assistant
Disallow
Feature
Manager
Assistant
Fwd RNA
n/a
Disallow
Fwd Busy
n/a
Disallow
Fwd DND
Allow - drop assistant
Allow
Handsfree
Allow
Allow
Hold
Allow - drop assistant
Allow (no Music On Hold)
Mute
Allow
Allow
Speakerphone
Allow
Allow
Feature
Manager
Assistant
Call pickup
n/a
n/a
Speed dial
Allow (ignore)
Disallow
Line redirect
n/a
Disallow
Toggle Fwd to VM
Allow
Allow
Release
Allow - drop assistant
Allow
70
CHAPTER 3: FEATURE SETTINGS
WhisperPage
Restrictions
Feature
Manager
Assistant
User park
Allow - drop assistant
Disallow
Feature
Manager
Assistant
Hunt Group Logging
Allow
Disallow
Hunting Service
n/a
n/a
Last Number Redial
Allow
Disallow
Lock unlock
Allow
Disallow
Orig startup
n/a
n/a
Feature
Manager
Assistant
System info
Allow
Disallow
Term startup
n/a
n/a
Transfer
Allow - drop assistant
Disallow
User password
Allow
Disallow
Camp On
Allow - drop assistant
Disallow
Volume Up / Down
Allow
Allow
Feature
Manager
Assistant
VTL merge
n/a
n/a
Bridged phones
Allow
n/a
Mapped Analog Line Card Allow
n/a
VTLs
Cannot go across VTL
Cannot go across VTL
WhisperPage restrictions include:
■
Only the administrator can:
■
■
■
■
Create a domain
Add telephone users to a domain that allows WhisperPage to be
invoked
Add telephone users to a domain that allows a WhisperPage to be
received on a particular extension
Multiple assistants cannot whisper to the same extension at the same
time.
WhisperPage
71
■
An assistant may initiate only two WhisperPage sessions at any one
time (one or both on hold), provided that there is a line available for
each session.
■
While using WhisperPage, if the party speaking to the manager hangs
up and completes the call, the system disconnects the assistant from
the call.
The system displays an error message to the assistant on the display
panel and plays a feature error tone.
■
The assistant and the manager must be on the same system.
You cannot use the WhisperPage feature over VTL /Q.SIG/ T1 tie lines
or /PRI / BRI/ T1 E&M robbed bit lines.
■
The system has a resource pool of 42 multicast addresses for the
WhisperPage feature.
There are no limits as to the maximum number of multicast addresses
that any one feature can use. It is possible for another feature to
exhaust the addresses in the resource pool.
■
Use the DND feature to implement Decline Whisper.
■
On an ATA, any feature that the manager tries to invoke disconnects
the assistant from the call.
If the manager presses flash hook on an ATA to enter a feature code,
the system invokes hold on the manager's device.
■
On an ATA, a telephone user cannot distinguish the difference
between Supervisory Monitoring Whisper Mode and WhisperPage.
There is no display panel on an ATA, and the tone is identical for both
features.
For more information about configuring WhisperPage, see the online
Help.
72
CHAPTER 3: FEATURE SETTINGS
4
SYSTEM MAINTENANCE
This chapter describes how to manage system-level maintenance
operations for the system, including:
■
System Backup
■
System Restore
■
Import / Export Data
■
Reboot/Shutdown
■
Password Administration
■
Call Report Settings
■
Purge Database
■
Manage Data
■
Disk Mirroring
For more information about these topics and configuration procedures,
see the online Help.
System Backup
You can back up a system database at any time. To ensure a successful
restoration of your database, be sure that the version number of the
backup file matches the version number of the system software.
For example, to restore the data on a system running release R6.0, use a
backup file from release R6.x, not from release R5.1 or lower. If you
restore a database that you saved on an older release, the operation will
succeed. However, if there is a change in the database schema between
the old and new releases, the restore will fail.
CAUTION: 3Com does not support the restoration of a database from an
older version of the system software.
74
CHAPTER 4: SYSTEM MAINTENANCE
3Com recommends this backup policy:
■
Back up your database before you upgrade the system software.
A backup of your system data includes voice mail messages and
licenses only if you specify that you want to include them. If voice mail
and licenses are not included when the system data is backed up, you
cannot specify that you want to restore voice mail and licenses during
a restore operation.
You can include only NBX Messaging voice mails in the backup file. If
you use a third-party messaging system, voice message backup and
restore are separate procedures that are not a part of the NBX NetSet
utility.
■
When you upgrade system software, answer Yes when the software
prompts you to include the database in the upgrade process.
■
After an upgrade, back up the database again.
■
After you make any administrator-level configuration changes, back
up the database.
■
To ensure that you capture changes that telephone users make to their
personal settings, perform frequent or, if possible, daily backups.
During a backup operation, a series of status windows tracks the steps.
Some steps may occur quickly so that you do not see the status window.
For example, you may see the status window appear to go from step 1 to
step 4, if steps 2 and 3 complete quickly.
A system task, which is independent of all other system tasks, backs up
your database. You can safely click your browser’s Back or Stop buttons,
exit your browser, or shut off your computer before the backup operation
completes without interfering with the backup.
If another administrator tries to back up the system database before the
current backup task completes, a message warns that a backup is
currently in progress.
The message includes:
■
The IP address of the computer from which the backup was started
■
The time that the backup was started
■
The current step of the upgrade process
System Backup
75
The seven steps in the backup operation include:
1 Backup Starting — The system begins the backup operation. The status
window displays step 1 of 7.
2 Backing up Database — The system locks the databases during this
step. The status window displays step 2 of 7.
3 Backing up Voice Mail — If you enable the Include NBX Voice Mail
check box, the system backs up voice mail messages for all telephone
users. The system locks Auto Discovery and voice mail access during this
step. The status bar displays step 3 of 7.
4 Backing up Voice Mail Data — The system backs up greetings and
name announcements of all telephone users. The status bar displays step
4 of 7.
5 Backing up License — If you enable the Include NBX Licenses check
box, the system backs up licenses on the system. The status bar displays
step 5 of 7.
6 Creating Backup file — The system adds all files created during the
backup process to a single backup file. The status bar displays step 6 of 7.
7 Backup Finishing — The system deletes temporary files created during
the backup operation. The status bar displays step 7 of 7.
Saving the Backup File
After the system completes the backup operation, it displays the name of
the backup file and gives you the opportunity to save the file in a location
you choose, which is typically on the disk drive of your PC or on the disk
of another computer in your network. 3Com recommends that you save
the backup file when prompted to do so.
The system keeps a copy of the most recent backup file on your system.
Each time you perform a backup operation on the database, the system
overwrites this file.
If you choose to not save the backup file during the backup procedure or
if you forget to save it, you can save it later. However, if you perform
another backup, the prior backup file is no longer available.
Cancelling a Backup Operation
You can cancel the currently active backup operation. When you click
Cancel, the system immediately asks you to confirm that you want to
cancel the backup operation. If you click Yes, the system first completes
76
CHAPTER 4: SYSTEM MAINTENANCE
the current step of the backup operation and then cancels the backup
operation.
Depending on the size of your database, some of the steps in the backup
operation can take several minutes to complete. Please allow time for the
system to complete the current step and respond to your cancel
command.
System Restore
You can restore a database using a backup file that is from the same
version as the running system software. For example, to restore the data
on a system running version R4.3.3, use a backup file from version
R4.3.3; do not use a backup file from R4.3.2 or lower. If you restore a
database that you saved on an older release, the operation will succeed.
However, if there is a change in the database schema between the old
and new releases, the restore will fail.
You can convert configuration data stored with an older software version
to a newer software version. You may need to do this if you have installed
a new version of the software but you want to use older configuration
data. During normal operation, you do not need to use this function.
CAUTION: 3Com does not support the restoration of a database from an
older version of the system software. In addition, you can severely
damage an NBX 100 system if you try to restore a database from a
V5000, V3000, V3001, or V3001R system. Do not attempt this operation
under any circumstances.
Before you restore a database, note these considerations:
■
Verify that your system has enough installed licenses to support the
number of devices and ACD agents in the database that you are
restoring. If you restore a database that includes more devices and
ACD agents than your system has licenses for, the system cannot add
those devices and ACD agents to your configuration. For more
information about licensing, see the NBX Installation Guide.
■
A backup of your system data includes voice mail messages and
licenses only if you specify that you want to include them. If voice mail
and licenses were not included when the system data was backed up,
you cannot specify that you want to restore voice mail and licenses
during a restore operation.
Import / Export Data
77
To restore your database from a saved backup file:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System Maintenance > System Restore.
3 Enable the appropriate radio button and do either of these steps:
a Browse to locate the current backup file.
b Use the drop-down list to select an earlier software version from
which to convert configuration data.
4 Click Restore Database.
If you chose a backup file, you can enable the Include NBX Voice Mail
check box. The Include NBX Licenses check box is inactive because
licenses are not part of a database migration.
If you chose an earlier software version from which to convert
configuration data, click OK when the system provides cautionary
information about the effect of a restoration on system operation and
prompts you to confirm that you want to restore the database.
5 Click Yes to restore the database.
The system automatically reboots after the database file is loaded.
Import / Export
Data
You can to import telephone data from a file on a PC to the database, or
export telephone data from the database to a file on a PC (click System
Maintenance > Import/Export Data).
The data is in .CSV format, which is a Microsoft Excel convention. This
method lets you populate many telephone user records into the database
in a single operation.
CAUTION: Be sure that you are familiar with data in this format before
you import or export data. Otherwise, you may inadvertently propagate
incorrect data into the database.
Each record of the data consists of the following fields:
■
Extension
■
First(Name)
■
Last(Name)
78
CHAPTER 4: SYSTEM MAINTENANCE
■
Title
■
CoS
■
Location1
■
Location2
■
Department
■
Telephone Group
■
Device Type
■
MAC Address
■
Channel
■
Forward to Auto Attendant
■
Receive Maintenance Alert
■
Exclude from LCD
■
Exclude from Name Directory
To manage these settings, click Telephones and System-Wide Settings.
Reboot/Shutdown
You must reboot the system after you upgrade software and you must
shut down the system software before you turn off power to your
system.
To reboot or shutdown the system:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System Maintenance > Reboot/Shutdown.
3 See the online Help for procedures to reboot and shut down the system.
CAUTION: If you remove power from the system without first shutting
down the system software using the NBX NetSet Shutdown function, the
operating system must perform a file system check during the next
startup cycle to ensure file integrity. The file system check significantly
increases the time it takes for the system to come to a ready state. During
a file system check operation, the Call Processor’s S1 and S2 status lights
flash in an alternating pattern.
Password Administration
Password
Administration
79
The Password Administration window enables you to manage passwords.
The most common use is to reset a telephone user’s forgotten password.
To set system passwords:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System Maintenance > Password Administration.
3 From the drop-down list, select which of these types of passwords you
want to set:
■
Change Administrator Password — Resets the password for
administrator access to NetSet.
After you change an administrator password, record the new
password. There is no “back door” password to use if you lose this
password. If you change the default 4-digit password to an 8-digit or
longer password, you cannot revert to a 4-digit password.
■
Reset User Password — Resets the password to a telephone user’s
extension. After you reset the password, instruct the telephone user to
change to a new password as soon as possible to ensure system
security.
■
Auto Attendant Password — Limits access to Auto Attendant
settings and functions.
■
System Backup Password — Enables automated backups from an
external system.
■
General Call Data Reporting Password — Limits access to Call
Detail Reports, an optional component of the system. See “Call
Report Settings” on page 80 for more information.
■
ACD Call Data Reporting Password — Limits access to ACD Call
Detail Reports.
■
Virtual Tie Lines Password — Enables calls over Virtual Tie Lines
(VTLs) to “hop off” after they reach the destination system. The call
then appears to originate at the destination system. See Chapter 11
for more information about setting up VTLs.
■
Hunt Group Voice Mail Password— Resets the password for the
Hunt Group extension number.
80
CHAPTER 4: SYSTEM MAINTENANCE
Call Report Settings
■
Hunt Group Supervisory Monitoring Password— Resets the
password that allows the Hunt Group supervisor to monitor calls to
hunt group members.
■
ACD Group Voice Mail Password— Resets the password for the
ACD Group extension number.
■
ACD Group Supervisory Monitoring Password— Resets the
password that allows the ACD Group supervisor to monitor calls to
ACD group agents.
■
TAPI Voice Mail Password— Resets the password for the TAPI Route
Point extension number.
■
TAPI Route Point Supervisory Monitoring Password— Resets the
password for the Hunt Group supervisor to monitor calls to hunt
group members.
The Call Processor captures information about all outgoing and incoming
calls made through the system. To view this call information in detail,
install Call Reports (Downloads > Applications > NBX Call Reports) on a
networked computer as specified later in this section. Then, download
the call report information, which is referred to as call detail reports, from
the system to a local hard drive.
After you install the NBX Call Reports software, you can:
CDR Changes At
Release R6.0
■
Retrieve calling data from the system.
■
Generate formatted reports.
■
Export reports in formats suitable for use with third-party reporting
software, spreadsheets, databases, and word processing applications.
■
Export your call data in HTML format for publication on a web server.
■
Export reports to a disk file or directly to a Microsoft mail message or a
Microsoft Exchange folder.
The release R6.0 system software has enhanced NBX Call Reports to
provide more data clarity and completeness for the CDR client reports.
These CDR enhancements include the following:
■
Logs the call records in XML format.
■
Logs all parties in the call.
Call Report Settings
81
■
Logs a record each time the call topology changes (that is, whenever
another party is added or removed).
■
Logs feature data on a per-party basis (that is, one or more sets of
feature data can be present in the same CDR record).
■
Logs external as well as internal calls. If you want to view external calls
only, you can select the external call report.
■
Supports backward compatibility for R5.0 CDR clients.
■
Introduces new data fields as subtags wherever necessary.
Additional CDR Fields
There are five new CDR fields at release R6.x. Two fields pertain to all
basic calls in release R6.x.
■
Call Answered Time — A timestamp that indicates when the call
was answered. (This is a mandatory field.)
■
CallPrivacy — Enables calls marked as Private to be treated as private
calls. (This is an optional field.)
The other three new fields are subtags, each of which are associated with
a feature.
<Facd> — This subtag appears only for those parties having ACD data.
This is placed under the party tag. (This is an optional tag.)
<Fmwb> — This subtag appears only for those parties having
Supervisory Monitoring data. This is placed under the party tag. (This is
an optional tag.)
<Fwp> — This subtag appears only for those parties having WhisperPage
data. This is placed under the party tag. (This is an optional tag.) <Fwp>
uses the some of the fields that are present under the <Fmwb> subtag.
New File Format
Release R6.xrequires CDR to use XML instead of CSV as a file format.
However, the NBX NetSet utility allows you to choose the file format you
want to use.
Use the following table to understand the relationship between CDR at
previous releases and release R6.x:
82
CHAPTER 4: SYSTEM MAINTENANCE
Current CDR
Installation
Configuration
Description
CDR 6.x (NBX)
Select the option
Enabled for XML
All CDR records are in XML format,
including the CDR records for the
release R6.x feature.s
CDR 5.0 (NBX)
Select the option
Backward
Compatible for
CSV
The records are in CSV format; this
does not include any new records for
release R6.x features. This is the
default option when customers
upgrade from release R5.0 to release
R6.x. All settings related to purge
interval and logging of internal calls
are retained as in release R5.0.
pre-R5.0 CDR (NBX)
There is no option
for supporting
pre-R5.0 CDR
operations. Select
the option Enabled
for XML.
If clients upgrade from pre-release
R5.0 versions to the CDR 6.x version
directly, then backward compatibility
is not provided, and clients must
view the CDR records in XML format.
If clients must view CDR records in
CSV format, the upgrade path is as
follows:
pre-R5.0 CDR > CDR 5.0 > CDR 6.x
CDR Client 6.0
Interaction with
release R5.0
Unsupported
CDR Client 6.0
Interaction with
release R6.x
Supported
CDR Client 6.0 and
CDR Client 5.0
Installation on same
device
Unsupported. You cannot install the
release R6.0 and release R5.0 clients
on the same device.
Call reports do not include information about the locked or unlocked
status of telephones.
Windows
Environment
Specifications
Your computer must meet these minimum requirements to run Call
Reports:
■
Processor — Pentium 166MHz or higher
■
Operating System — Microsoft Windows 2000 (Service Pack 2),
Windows XP, or Windows Vista
■
RAM — 64 MB on Windows 2000; 128 MB on Windows XP or
Windows Vista
■
Network — Network connectivity to the Call Processor
■
Disk Space — At least 40 MB of free disk space
Call Report Settings
Installing Call Reports
83
To install NBX Call Reports:
1 Click Downloads > Applications.
2 Enable the NBX Call Reports radio button.
3 See the online Help topic for information about installation procedures.
Configuring Call
Reporting
You can configure your system to save call information, and then use the
Call Reports function to view the information in a variety of formats. You
can create a password-protected logon for telephone users so that the
users can access call report information. This logon does not provide
administrator privileges to telephone users.
Call Detail Report (CDR) records incorporate caller ID information to
identify a caller. VTLs transmit a maximum of 30 characters for the caller
ID, which may cause longer caller IDs to lose excess characters. See
“Creating a Pretranslator for VTL Calls” on page 301 for more
information about how to configure a VTL pretranslator to avoid
inaccurate data in CDR records.
To configure call reporting, click System Maintenance > Call Report
Settings and see the online Help for more information.
The software supplied by or on behalf of 3Com can mask or scramble the
last four digits on call records. If you do not select this function, the
software records call numbers without any digits masked or scrambled.
The collection, storage, or manipulation of personal data such as these
call numbers may incur obligations under local laws, such as those
relating to data protection or privacy. These legal requirements differ
from country to country and it is your responsibility to comply with all
such obligations.
3Com accepts no liability for your failure to comply with local laws
regarding the collection, storage, or manipulation of such information
and data.
Purge CDR
You can purge old Call Detail Report (CDR) data from the system.
To purge CDR data:
1 Click System Maintenance > Call Report Settings.
2 Click Purge CDR.
84
CHAPTER 4: SYSTEM MAINTENANCE
Purge Database
When you purge the database, the software removes existing telephone
user and device data that you added to the system, restores factory
defaults, and causes an automatic reboot.
To purge data:
1 Click System Maintenance > Purge Data.
2 Click Purge Database.
The Purge Database feature does not affect your IP connectivity to the
NBX NetSet utility. After a database purge, the system continues to use
the IP address, subnet mask, default gateway, and host name that you
have assigned.
Purge Database and
CDR
You can purge Call Detail Reports (CDR) data at the same time that you
purge telephone user and device data.
To purge data and CDR data:
1 Click System Maintenance > Purge Data.
2 Click Purge Database and CDR.
You may need to purge your existing CDR records if you perform an
upgrade. See the appropriate Software Upgrade Guide for details.
Purge All Voice Mail
You can delete all voice mail messages for all telephone users.
To purge voice mail:
1 Click System Maintenance > Purge Data.
2 Click Purge all Voice Mail.
Mailbox greetings are not affected.
Manage Data
This section describes these system data management operations:
■
Migration
■
Restore Database From Another Version
Manage Data
Migration
85
Table 20 describes the supported migration paths to move your data from
one system platform to another.
Table 20 Data Migration Platforms and Software Revisions
Source
Target*
Notes
NBX 100
V5000
The NBX 100 must be at release
R4.2.X or higher.
V3001R
V3001
V3000
V3000
V5000
V3001R
The V3000 system must be at
release R4.4.X or higher.
V3001
V3001
NBX 100
Unsupported.
V5000
The V3001 system must be at the
latest R6.0 release.
V3001R
V3000
V3001R
NBX 100
Unsupported.
V5000
The V3001R system must be at
release R6.0 or higher.
V3001
V3000
V5000
NBX 100
Unsupported.
V3001R
The V5000 system must be at
release R4.2.X or higher.
V3001
V3000
NBX 100
Unsupported.
* Must be release R5.0 or higher; for V3001R systems, must be release R6.0 or higher; for V3001
systems, must be the latest R6.0 release.
Data Migration Notes and Considerations
Before you begin a data migration, be sure that you understand these
important considerations:
■
You cannot remove the disk drive from one type of system platform
and install it into a different platform. If you attempt to do so, the
system will not boot properly.
■
Licenses are not part of a database migration. The licenses on your old
system do not work on the new system. Your new system comes with
86
CHAPTER 4: SYSTEM MAINTENANCE
its own set of license keys that you must enter into the new system
before you migrate your data.
■
The target system must be licensed to support the capacities of the
source system. For example, you cannot move the data from a V5000
system with 1000 devices successfully onto a V3000 system, unless
you install the memory upgrade and a license to support at least 1000
devices on the V3000 system.
■
You can choose to include or exclude telephone users’ voice mail
messages when you perform the data migration.
■
The system software version on the target system must be equal to or
higher than the software version on the source system. For example,
you cannot move data from a release R5.0 system onto an release
R4.3 system using the data migration feature. The target system
software must be at release R5.0 or higher.
■
A data migration operation does not alter data. For example, it will
not change extensions. To change between a 3-digit dial plan and a
4-digit dial plan requires a separate series of steps, which “Converting
Extensions” in Chapter 11 describes.
Migrating Data
To migrate data from one platform to another, use the NBX NetSet utility
to perform a backup operation on the source platform and then perform
a restore operation, using that backup file, on the target platform. 3Com
recommends that you perform the migration only during nonbusiness
hours so that you do not impact telephone users.
To migrate data:
1 Install the target system.
2 Install your license keys on the target system.
Note that you need new license keys for the target system. You cannot
load a license backup file from the source system nor can you use the
license keys from the source system. License keys are generated from
each system’s unique system ID number.
3 Perform a backup operation on the source system (click System
Maintenance > System Backup).
Enable the Include NBX Voice Mail check box if you want telephone
users’ voice mail messages to be available on the target system.
Disk Mirroring
87
4 Use the backup file you just created and perform a database Restore
operation on the target system (click System Maintenance > System
Restore).
Restore Database
From Another Version
You can migrate configuration data stored with an older software version
to a newer software version. You may need to do this if you install a new
version of the software but you want to use older configuration data.
During normal operation, you do not need to use this function.
From the System Restore window (click System Maintenance > System
Restore), select the source version from which you want to migrate the
data and click Restore Database.
Disk Mirroring
The V3001R and V5000 systems supports disk mirroring, using RAID1
technology, to provide data security and throughput speed. When you
fully partner the mirror disk with the master system disk, the system
writes all data to the mirror disk as well as to the master disk. If data is
read from disk, the software can read from either disk, which can
improve data access times.
If either disk fails in a fully mirrored system, the system software uses only
the remaining good disk, and system operation continues. Status
information is available on the Call Processor front panel status lights to
indicate when a disk fails and which disk to replace. After you replace a
failed disk and restart the system, the software brings the new disk up to
a fully mirrored state. The system typically takes from 30 to 90 minutes to
complete the mirroring process, depending on the amount of data on the
master disk.
Adding a Mirror Disk
If your V3001R or V5000 system uses a single disk, you can add a mirror
disk. The disk you add must have at least the same storage capacity as
the disk in the system. You must obtain a disk mirroring license to convert
a single-disk system to use disk mirroring. You also need a Phillips
screwdriver to complete this process.
CAUTION: When you add a mirror disk, you must perform a system
database backup and a system shutdown. 3Com recommends that you
add a mirror disk only during nonbusiness hours.
88
CHAPTER 4: SYSTEM MAINTENANCE
To add a mirror disk:
1 Back up the database on the system:
a Click System Maintenance > System Backup > Backup.
b Specify a location for the backup file.
2 Install the disk mirroring license:
a Obtain the license key from your dealer.
b Click Licensing and Upgrades > Licenses > Add License.
c Type the license key in the License Key field.
d Click OK.
3 Shut down the system (click System Maintenance > Reboot/Shutdown >
Shutdown).
4 Install the second disk drive:
a Unlock the disk tray.
b Unscrew the two retaining screws.
c Remove the disk tray.
d Connect the IDE disk cable to the disk drive.
e Connect the power harness to the disk drive.
f Fasten the new disk to the disk tray using your Phillips screwdriver and
the screws provided with the disk.
g Reinsert the disk tray.
h Screw in the two retaining screws and lock the disk tray in place.
5 Restart the system.
6 Verify that the disks begin the mirroring process.
On the Call Processor front panel, check the four status lights under the
PWR and S1 labels. The status lights labeled 1, 2, and 3 (Figure 3) indicate
disk status.
Disk Mirroring
89
Figure 3 Disk and Power Status Lights
S
1
P
W
R
1
2
3
Table 21 describes the possible states of the status lights.
Table 21 Disk Status Light States
Explanation
LED 1
LED 2
LED 3
PWR
Attempting to boot from disk 0 (zero)
Off
On
Off
On
Attempting to boot from disk 1
Off
Off
On
On
Boot process complete, system initializing
Flashing N/A
N/A
On
System is running
On
N/A
N/A
On
Flash codes indicate disk problem:
N/A
Flashing Flashing On
Using disk 0 (zero) only
N/A
On
Off
On
Using disk 1 only
N/A
Off
On
On
Synchronizing — disk 0 is valid, disk 1 is
becoming a fully mirrored disk. LED 3 flash rate
indicates progress.
N/A
On
Flashing On
N/A
Flashing On
■
2 flashes: No valid disk (system is halted)
■
3 flashes: Two valid disks, but they are not
paired (system is halted)
■
4 flashes: Configuration problem (system is
halted)
■
5 flashes: Two disks present, but no
mirroring license
If LED 3 stops normal flashing and intermittently
flashes twice, the mirroring process has failed.
Synchronizing — disk 1 is valid, disk 0 is
becoming a fully mirrored disk. LED 2 flash rate
indicates progress.
If LED 2 stops normal flashing and intermittently
flashes twice, the mirroring process has failed.
On
90
CHAPTER 4: SYSTEM MAINTENANCE
Table 21 Disk Status Light States (continued)
Explanation
Verifying a Failed
Disk Drive
LED 1
LED 2
LED 3
PWR
LED 2 and LED 3 flash alternately: the two disks N/A
are resynchronizing
Flashing Flashing On
Synchronized
On
N/A
On
On
If either disk fails while in a fully mirrored state, the system continues to
operate. The disk status light states described in Table 21 indicate which
drive has failed.
To verify the status of a disk drive, see the Disk Status window:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Reports > System Data
3 Click Disk Status.
Reverting to a
Single-Disk System
If disk mirroring is currently active, you can convert the system to operate
with a single disk. You need a Phillips screwdriver to complete this
process.
To revert to a single-disk system:
1 Use Table 21 to find out which disk is the mirrored disk.
2 Shut down the system (click System Maintenance > Reboot/Shutdown >
Shutdown).
3 Remove the mirrored disk drive:
a Unlock the disk tray.
b Unscrew the two retaining screws.
c Remove the disk tray.
d Disconnect the disk data cable from the mirrored disk drive.
e Disconnect the power harness from the mirrored disk drive.
f Unfasten the mirrored disk from the disk tray using the Phillips
screwdriver and the screws provided with the disk.
g Reinsert the disk tray.
h Screw in the two retaining screws and lock the disk tray in place.
4 Restart the system.
Disk Mirroring
91
5 Use the NBX NetSet utility to remove the disk mirroring license from the
NBX NetSet utility:
a Click Licensing and Upgrades > Licenses.
b Click Remove License.
c From the Select License to Remove drop-down list, select Disk
Mirroring License.
6 Click OK.
92
CHAPTER 4: SYSTEM MAINTENANCE
5
TELEPHONE CONFIGURATION
This chapter describes how to configure and manage devices on the
system. It describes these topics:
■
Adding, Removing, and Modifying Telephones
■
Adding a Remote Telephone
■
Creating and Managing Bridged Extensions
■
Creating and Managing Telephone Groups
■
Recording and Monitoring Telephone Calls
■
Creating and Managing Button Mappings
■
Changing Device IP Settings
■
Configuring the 3Com Attendant Console
■
Connecting and Managing Analog Devices
For more information about these topics and configuration procedures,
see the online Help.
For information about installing the system hardware components, see
the NBX Installation Guide.
Adding, Removing,
and Modifying
Telephones
Adding a New
Telephone
This section describes how to add, remove, and modify telephones in the
NBX NetSet utility. You can also review the status of each device and
configure button mappings for 3Com telephones.
You can use two methods to configure a new telephone:
■
Auto Discovery method — Auto Discovery is the simplest and most
common method to add a new telephone. When you enable Auto
Discovery and then connect a new 3Com Telephone to the LAN, the
new telephone receives the next lowest available extension number
94
CHAPTER 5: TELEPHONE CONFIGURATION
and a default set of properties. The telephone’s display panel displays
the extension.
■
Manual method — You can use the NBX NetSet utility to disable
Auto Discovery and configure telephones manually. However, if you
have many telephones to configure, manual configuration can be a
tedious and error-prone process.
For either method, you need to connect the telephone to the network. If
you use Auto Discovery, enable the Auto Discover Telephones check box
before you connect the telephone. If you add a telephone manually, you
can connect the telephone before or after you use the NBX NetSet utility
to add it.
Connecting the Telephone
Instructions for connecting the telephone to power and the network
depend on your power source and the type of telephone. See Chapter 3
in the NBX Installation Guide or the telephone packing sheet for
telephone connection information.
Adding a New Telephone Using Auto Discovery
Before you enable Auto Discovery, verify that a 3-digit or 4-digit dial plan
is installed on the Call Processor and that you have specified a starting
extension. See the NBX Installation Guide for more information.
To add a new telephone using Auto Discovery:
1 Click System-Wide Settings > Auto Discovery.
2 Optionally, clear all check boxes associated with autodiscovering devices.
3 Enable Auto Discover Telephones, and then click Apply.
4 Optionally, enable the Auto Add Phones to Call Pickup Group 0 check
box.
Regardless of whether you select this check box, you can change the call
pickup group for any telephone later. See “Call Pickup” on page 49 for
more information.
5 Click OK.
Adding, Removing, and Modifying Telephones
95
For each telephone that you want to autodiscover:
1 Remove the telephone from the packing box.
2 Connect the telephone to power and the network according to the
instructions in the telephone packing sheet or the NBX Installation Guide.
3 Wait until an extension number displays in the telephone’s display panel.
Devices that require a license, such as the 3102 Business Telephone, the
3101 and 3101SP Basic Telephones, and the 3105 Attendant Console, do
not display an extension number until you add the license to the system.
If you have not entered a license for a telephone, its display panel displays
the device’s MAC address and a rotating hyphen.
You can now disconnect the telephone and move it to its destination. The
telephone retains its extension and button mappings.
Adding a Telephone Manually
To add a new telephone manually:
1 Click Telephone Configuration > Telephones.
2 Click Add.
3 Enter the appropriate values in the fields.
See the online Help for more information.
4 Click Apply to configure this telephone.
You can configure additional telephones, if necessary.
5 Click OK.
The procedure to add SIP devices to a SIP-mode system differs from the
procedure to add 3Com telephones to a non-SIP system. You do not use
the NetSet Add telephones window to add a SIP device. See the NetSet
online help for more information.
Modifying a
Telephone
To modify a telephone:
1 Click Telephone Configuration > Telephones.
2 Click the extension of the telephone that you want to modify from the
list.
3 In the Modify window, change the appropriate fields.
See the online Help for more information about the dialog box fields.
96
CHAPTER 5: TELEPHONE CONFIGURATION
4 Click OK.
Checking a
Telephone’s Status
To check the status of a telephone:
1 Click Telephone Configuration > Telephones.
2 Click the extension of the telephone for which you want a status report.
3 Click the Status tab.
4 View the device status and see the online Help for information about
options.
5 Click OK.
Removing a
Telephone
To remove a telephone from the system:
1 Click Telephone Configuration > Telephones.
2 Select the telephone, or telephones, that you want to delete and click
Remove Selected. To select all telephones, enable the Select check box.
3 Click OK when the dialog box prompts you so that the system removes
the selected telephone.
4 Click User Configuration > Users.
5 Select the extension, or extensions, that you want to delete and click
Remove Selected. To select all telephones, enable the Select check box.
6 Click OK when the dialog box prompts you so that the system deletes the
selected extension.
If you do not delete the telephone user, the extension of the removed
telephone becomes a phantom mailbox.
Rebooting a
Telephone
To reboot a telephone:
1 Click Telephone Configuration > Telephones.
2 Click the extension of the telephone that you want to reboot.
3 Click the Status tab.
CAUTION: If the telephone has an active call, you will disconnect the call
when you reboot the telephone.
4 Click Reset Device and then click OK.
Adding a Remote Telephone
97
You can also reboot a telephone by unplugging the power connector
from the telephone and then plugging it in again.
Adding a Remote
Telephone
Remote NAPT
Telephone
Configuration
The system software (release R4.2 and higher) supports Network Address
Port Translation (NAPT, also called NAT overloading). NAPT allows you to
put a 3Com Telephone behind a device that applies network address
translation at a remote location, such as a home office, and connect to
the Call Processor through an Internet connection. A typical configuration
is to connect a cable or DSL modem to a small office or home office
router that includes a firewall and Ethernet ports. You connect the 3Com
Telephone directly to one of the Ethernet ports. Another option is use the
pcXset soft telephone application instead of an 3Com Telephone.
This section summarizes the tasks you must complete to configure a
3Com Telephone for operation behind the NAPT device. Because the
configuration interface on each device varies, detailed procedures for
NAPT device configuration are beyond the scope of this guide. For
information about configuring the NAPT device, see the documentation
for that device.
To add a broadband connected telephone behind a NAPT device:
1 Verify that the system is set up for IP operations, either Standard IP or IP
On-the-Fly. If you are not using a VPN connection to establish access from
your home system to the system network, the system must have a public
IP address.
2 Use the NBX NetSet utility to enable Auto Discover Telephones
(System-Wide Settings > Auto Discovery) and then connect the 3Com
Telephone to the system.
Autodiscovering the telephone while it is connected locally to the
network allows the system to configure the telephone in the system
database and assign an extension number. You can manually add the
telephone to the system database instead of using the Auto Discover
feature.
3 Move the telephone to its intended location. Connect it to power and
then use the telephone Local User Interface (LUI) utility to program these
settings:
■
Call Processor MAC address — Required only when the network has
more than one Call Processor.
98
CHAPTER 5: TELEPHONE CONFIGURATION
■
Telephone IP address — A private IP address matching the IP address
scheme on the LAN side of the NAPT device but outside of the DHCP
address range configured in the NAPT device. The telephone must
have a static IP address. For the pcXset application, this is the IP
address of the computer.
■
Call Processor IP address — The IP address of the Call Processor with
which the telephone must communicate. If you are not connecting to
the network through a VPN connection, the system must have a
public IP address.
■
Subnet Mask — The address mask in use on the LAN side of the NAPT
device.
■
Default Gateway — The IP address of the NAPT device on the LAN.
For details about how to use the LUI utility, see “Telephone Local User
Interface Utility” on page 415.
4 Configure the NAPT device.
Use the device’s user interface to map UDP ports 2093-2096 to the 3Com
telephone IP address. These UDP ports are registered ports for system
operations. This mapping feature, known as virtual server, port mapping,
port range forwarding, or rules, is required to allow traffic to pass to and
from the 3Com Telephone.
Creating and
Managing Bridged
Extensions
Bridged extensions allow you to have the extension of a primary
telephone appear on one or more secondary telephones. Most activities
associated with the extension can be performed on both the primary
telephone and any of the secondary telephones. However, you cannot
use a bridged extension on a secondary telephone to place a call.
Creating and Managing Bridged Extensions
99
On any system, you can configure a maximum number of primary
telephones and a maximum number of bridged extensions on primary
telephones. See Table 22.
Table 22 Maximum Bridged Extensions
System
Device Limit
Maximum
Number of
Primary
Telephones
Maximum Number
of Bridged
Extensions on
Primary Phones
V3001R
1500
400
1200
V3001
250
400
1200
V3001*
1500
400
1200
V3000
250
400
1200
V3000*
1500
400
1200
V5000
250
250
1200
V5000
More than 250
400
1200
NBX 100
200
100
300
* With optional memory upgrade
There are no restrictions on the number of secondary telephones or the
number of bridged extensions on secondary telephones.
Provided that you do not exceed the limits shown in Table 22, you can
configure the maximum number of bridged extensions using any
combination of primary telephones and bridged extensions. For example,
on a V5000 system, you can configure 400 primary telephones with three
bridged extensions each or 300 primary telephones with 4 bridged
extensions each to reach the limit of 1200.
You can configure a different number of bridged extension buttons on a
primary and an associated secondary telephone. For example, if a primary
telephone has 5 bridged extensions, you can configure one of the
secondary telephones to have fewer (1 through 4) bridged extensions.
However, if all of the primary bridged extensions are in use, the person at
the secondary telephone will not be able to see all the calls.
You can define any one telephone as either a primary telephone or a
secondary telephone, but not both. If the telephone has an Attendant
Console associated with it, the bridged extension functions for the
telephone extend to the Attendant Console. For example, you can
configure an 3Com 2101 Basic Telephone with an associated Attendant
100
CHAPTER 5: TELEPHONE CONFIGURATION
Console as a primary telephone with up to 11 bridged extensions on
Attendant Console buttons.
You can configure bridged extensions on the same buttons that are used
for the telephone’s extension or on non-extension buttons. Before you
can create a bridged extension on a telephone, unlock the button
settings for the telephone group to which the telephone belongs (click
Telephone Configuration > Telephone Groups, select a group and then
click the Button Mapping tab).
You can view a report that lists the primary and secondary telephones on
which you have defined bridged extensions. See “Viewing
Bridged Extension Information” on page 108.
When you define bridged extension appearances on a primary telephone:
Example
Bridged Extensions
Configurations
■
Incoming calls appear on the bridged extension buttons first, followed
by the buttons (if any) associated with the primary telephone’s
extension. For example, by default, buttons 1, 2, and 3 are extension
appearances of the primary telephone. If you define buttons 4, 5, 6,
and 7 as bridged extensions on the primary telephone, incoming calls
appear on primary telephone buttons in the order 4, 5, 6, 7, 1, 2, 3.
■
Any bridged extension appearance that overlaps one of the defined
extension appearances for the primary telephone take precedence
over those extension appearances. For example, if you define buttons
3, 4, 5, 6, and 7 as bridged extension appearances on the primary
telephone, incoming calls appear on primary telephone buttons in the
order 3, 4, 5, 6, 7, 1, 2.
Example 1: An 3Com Business Telephone, extension 1044, is defined as
a primary telephone and buttons 2, 3, and 4 are defined as bridged
extension buttons. Two other 3Com Business Telephones, extensions
1055 and 1066, are defined as secondary telephones on which extension
1044 appears. On the 1055 telephone, buttons 10, 11, and 12 are
configured as the three bridged extension buttons for the 1044
telephone. On the 1066 telephone, buttons 4, 5, and 6 are configured as
bridged extension appearances.
If a call is made to extension 1044, it can be answered using any of the
following buttons:
■
Extension 1044 (primary telephone) — button 2
■
Extension 1055 (secondary telephone) — button 10
Creating and Managing Bridged Extensions
■
101
Extension 1066 (secondary telephone) — button 4
In this example, both secondary telephones use buttons 1, 2, and 3 as
extensions appearances for their own extensions.
Example 2: A 3Com Business Telephone with extension 1077 is defined
as a primary telephone and buttons 4, 5, 6, 7, and 8 are defined as
bridged extension buttons. Two other 3Com Business Telephones
(extensions 1088 and 1099) are defined as secondary telephones on
which extension 1077 is to appear. On the 1088 telephone, buttons 10,
11, and 12 are configured as bridged extension buttons. On the 1099
telephone, buttons 3, 4, 5, 6, and 7 are configured as bridged extension
appearances for extension 1077.
If a call is made to extension 1077, it can be answered using any of the
following buttons:
■
Extension 1077 (primary telephone) — button 4
■
Extension 1088 (secondary telephone) — button 10
■
Extension 1099 (secondary telephone) — button 3
Secondary telephone 1099 has only two extension appearances for the
1099 extension because button 3, by default an extension appearance
for the local telephone, has been used as a bridged appearance of
extension 1077.
The primary telephone has buttons 1, 2, and 3 as local appearances of its
own extension (1077). If multiple calls arrive at this telephone, they
appear on buttons 4, 5, 6, 7, and 8, followed by 1, 2, 3.
Buttons 1, 2, and 3 on the 1077 telephone are not defined as bridged
extension appearances. Therefore, they do not appear on either of the
secondary telephones. If the owner of the 1077 telephone makes a call
using any of these buttons, there is no indication (status light) of the call
on either secondary telephone. If there are five active calls on the 1077
telephone, and a sixth call is made to that extension, it rings only on the
1077 telephone, on the first unused button in the 1, 2, 3 group).
Defining Bridged
Extensions
The process of defining bridged extensions involves:
■
Defining Bridged Extensions on a Primary Telephone
■
Defining Bridged Extensions on a Secondary Telephone
102
CHAPTER 5: TELEPHONE CONFIGURATION
Defining Bridged
Extensions on a
Primary Telephone
On a primary telephone, you can define from 1 to 11 buttons as bridged
extensions. The buttons do not have to be next to each other.
Defining a bridged extension for a 3Com 3130 Manger’s Telephone
differs from other telephones. See “Defining Bridged Extensions on 3103
Manager’s Telephones” on page 104 for more information.
To define the bridged extensions for the primary telephone:
1 Click Telephone Configuration > Telephones.
2 Click the extension for the primary telephone.
3 Click the Button Mapping tab to display the Button Mapping window
(Figure 4).
Figure 4 Telephone Button Mappings Window
4 For each button that you want to include in the group of bridged
extension buttons:
a Select Bridged Extension from the drop-down list in the Type column.
Creating and Managing Bridged Extensions
103
b Type the extension number of the primary telephone in the Number
column.
Figure 4 shows a group of three buttons that have been configured as
bridged extension appearances for the extension (1066) on the primary
telephone.
5 Click OK.
Defining Bridged
Extensions on a
Secondary Telephone
After you have defined the bridged extension buttons on the primary
telephone, you can define the corresponding bridged extension buttons
on a secondary telephone. You can do this for as many secondary
telephones as you want.
To define the bridged extensions for a secondary telephone:
1 Click Telephone Configuration > Telephones.
2 Click the extension for the secondary telephone.
3 Click the Button Mappings tab to display the Button Mapping window.
4 For each button that you want to include in the group of bridged
extension buttons:
a Select Bridged Extension from the drop-down list in the Type column.
b Type the extension number of the primary telephone in the Number
column.
Figure 5 shows a group of three buttons that have been configured as
bridged extension appearances for the extension (1066) associated
with the primary telephone.
104
CHAPTER 5: TELEPHONE CONFIGURATION
Figure 5 Button Mapping Window After Mapping
5 Click OK.
Defining Bridged
Extensions on 3103
Manager’s
Telephones
To configure the 3Com 3103 Manager’s Telephone as a secondary
telephone and map a button as a bridged extension button, use the Type
drop-down list, as you would for any other phone. The maximum number
of button mappings for secondary bridged appearances is 8 (one for each
button).
To configure the 3Com 3103 Manager’s Telephone as a primary
telephone, you do not need to map primary bridged extensions to a
button. Use the Displayed Call Appearances section of the Button
Mapping window to configure the telephone (See Figure 6).
Creating and Managing Bridged Extensions
105
Figure 6 Telephone Button Mapping Window for 3Com 3103 Manager’s
Telephone
■
From the Primary Bridged Extensions Quantity drop-down list, choose
the number of primary bridged extensions, which also defines this
telephone as a primary telephone. The maximum number of primary
bridged appearances and system appearances, which you define from
the System Appearances Quantity drop-down list, cannot total more
than 12.
■
From the System Appearances Quantity drop-down list, choose the
number of system appearances for the telephone. The default number
of system appearances is 3. The maximum number of system
appearances and primary bridged extensions cannot total more than
12.
■
Click the check box Show caller ID on secondary bridged extensions
when on call check box so that this primary telephone’s extension
displays on the secondary telephones with which it is associated. If
you disable this option, the bridged extension button on the
secondary telephone lights, however, the display panel does not
display a Caller ID.
106
CHAPTER 5: TELEPHONE CONFIGURATION
The telephone’s display panel can display three system or bridged
extension appearances, which are mapped to the buttons to the left of
the display panel.
By default, bridged extensions have priority over system appearances. To
give system appearances priority, change the priority of the primary
bridged extension to a higher value. The lowest value in the priority field
provides the highest priority.
Example: If you configure the primary telephone for a total of three
system appearances and no bridged extensions, when all three lines are
in use, a fourth call does not display in the display panel and goes directly
to voice mail.
Example: If you configure the telephone for three system appearances
and one bridged extension, a call to the primary telephone uses the
bridged extension line and can be answered by associated secondary
telephones. Any other calls to the primary telephone use the system
appearance lines and cannot be answered by associated secondary
telephones. If all three lines are in use, a fourth call causes the Message
Waiting Indicator on the primary telephone to flash, but the display panel
does not display any information. However, you can answer the call on
the unused system appearance line. You can also make a call on an
unused line.
Example: If you configure the telephone for three system appearances
and two bridged extensions, the bridged extension lines take priority over
the system appearance lines. If you make a call and put it on hold, and
then make a second call, by default, both calls are on bridged extension
lines. Because both bridged extensions are in use, any calls to the primary
telephone are on system appearance lines, and cannot be answered by
associated secondary telephones.
Example: If you choose two primary bridged extensions and give them a
priority of 1 and choose one system appearance and give it a priority of 0,
the system appearance will have the higher priority. When you make a
call, by default, the call is on the system appearance line. This ensures
that calls to the primary extension are on bridged extension lines and are
available to associated secondary telephones. If all three lines are in use
and you make a fourth call, that call is on a bridged extension line.
Creating and Managing Bridged Extensions
107
Modifying Bridged
Extensions
You can modify bridged extensions on a primary telephone at any time.
Bridged extensions do not need to be on adjacent buttons on a primary
or a secondary telephone. You can have a different number of bridged
extensions on a primary and a secondary telephone.
Sample Calling
Situations Using
Bridged Extensions
This section describes typical telephone call situations involving bridged
extensions on primary and secondary telephones. For all the examples:
■
The primary telephone is an 3Com Business telephone (extension
1027) used by a manager (Alicia). This telephone has buttons 2, 3,
and 4 defined as bridged extension buttons. Button 1 is the manager’s
private line.
■
One secondary telephone, a 3Com Business Telephone (extension
1051), is used by the manager’s assistant (Bradley). On this telephone,
buttons 1, 2, and 3 are extension appearances for extension 1051 and
buttons 4, 5, and 6 are configured as bridged extension appearances
of the manager’s telephone (1027).
■
The other secondary telephone is also an 3Com Business Telephone
(extension 1018). The telephone is used by the person (Connie) who
answers the manager’s telephone whenever the manager’s assistant is
not available. Buttons 10, 11, and 12 are configured as bridged
extension appearances of the manager’s telephone (1027).
Example 1: If there are no active calls on Alicia’s telephone, a call made
to her telephone from either an internal or outside telephone rings on
button 2 on her telephone, button 4 on Bradley’s telephone and button
10 on Connie’s telephone.
Bradley answers the call by pressing button 4. After identifying the
person who is calling, Bradley places the call on hold and informs Alicia of
the call. Alicia presses button 2 on her telephone to take the call.
During the time that Bradley is talking to the caller, neither Alicia nor
Connie can access the call. Alicia can pick up the call only after it is placed
on hold by Bradley. Similarly, after Alicia picks up the call, neither Bradley
nor Connie can access the call. If Alicia wants to include either Bradley or
Connie in the call, she can set up a conference call.
Example 2: Alicia wants to place a call but wants to keep all three
bridged extensions available for incoming calls. Alicia can place the call
using button 1.
108
CHAPTER 5: TELEPHONE CONFIGURATION
Neither Bradley’s telephone nor Connie’s telephone shows any indication
that there is a call on Alicia’s telephone, because button 1 on Alicia’s
telephone is not configured as a bridged extension.
Example 3: Three incoming calls have arrived on Alicia’s telephone (on
buttons 2, 3, and 4). Alicia is talking on button 2, Bradley has placed the
second call on hold, and is talking to the third caller.
A fourth call arrives at Alicia’s extension and rings on button 1. Neither
Bradley nor Connie can answer this call because that button on Alicia’s
telephone is not a bridged extension appearance.
If a fifth call arrives at Alicia’s extension before the fourth call stops
ringing, it is sent directly to Alicia’s voice mailbox, because all buttons are
being used.
Example 4: A call arrives at Alicia’s telephone and the building has been
evacuated because of a fire. Neither Alicia, nor Bradley, nor Connie is
available to answer the call. After the number of rings that are configured
for Alicia’s telephone, the call is sent to Alicia’s voice mailbox.
Example 5: A call arrives at Alicia’s telephone and Bradley answers the
call, then places it on hold, and Alicia picks up the call. Bradley leaves the
area, asking Connie to answer his telephone and Alicia’s until he returns.
Alicia places the call on hold to pass the call back to Bradley but finds that
he is not available. Connie is not close enough to Alicia’s office to permit
Alicia to talk directly to her, so Alicia presses another button on her
telephone, calls Connie’s extension, and asks her to pick up the call.
Viewing
Bridged Extension
Information
You can view a list of all telephones on the system and find out which are
primary telephones and which are secondary telephones.
To view the bridged extensions information, click Telephone
Configuration > Telephones, and click Bridged Extensions, which displays
the NBX Bridged Extensions Report.
If a telephone is a primary telephone, the Bridged Extensions column
contains the extension of the telephone and the extension of each
associated secondary telephone. The Mapped Buttons column displays
the telephone’s extension once for each button that is mapped as a
bridged extension.
Creating and Managing Telephone Groups
109
Example: If extension 1002 is a primary telephone and extensions 1005,
1008, and 1019 are secondary telephones with 1002 mapped to them,
the Bridged Extensions column contains four extension numbers (1002,
1005, 1008, and 1019). If 3 buttons on the 1002 telephone are mapped
as bridged extensions, the Mapped Buttons column contains extensions
1002, listed 3 times.
Camp On Feature and
Bridged Extensions
There are some restrictions when you use the Camp On feature with
primary bridged extensions.
You cannot initiate Camp On with Call Transfer to queue a call to an idle
primary bridged extension line if the primary telephone user is on a call
on the default system appearance line. The system treats the Camp On
attempt as a blind transfer and routes the call to voice mail if the call is
not answered.
However, you can initiate Camp On with Call Transfer to queue a call to a
busy primary bridged extension line.
You can initiate Direct Camp On to queue a call to a busy primary bridged
extension, regardless of which line is in use. That is, the primary
telephone user can be using a system appearance line or a bridged
extension line.
Creating and
Managing
Telephone Groups
Telephone groups let you create common button mappings, which let
you assign specific actions to the buttons on an 3Com Business
Telephone. When you associate a group with a specific telephone, the
telephone inherits all the mappings of the group.
For example, when you use the NBX NetSet utility, you can create a group
called Sales that includes access buttons mapped to a set of CO lines.
When you add a new salesperson to the group, you specify the Sales
group for the telephone assigned to that person. All of the Sales group’s
button mappings are then available on that person’s telephone.
This section describes these topics:
■
Creating a New Telephone Group
■
Modifying a Telephone Group
■
Removing a Telephone Group
■
Viewing Telephone Group Membership
110
CHAPTER 5: TELEPHONE CONFIGURATION
Creating a New
Telephone Group
To create a new telephone group:
1 Click Telephone Configuration > Telephone Groups.
2 Click Add.
3 Type the name of the new group in the Group Name field.
4 Select an entry from the Telephone Type drop-down list.
5 To enable call recording and monitoring as the default setting for all
telephones in this group, enable the Call Record & Monitor check box.
You must install a call recording license before you can enable the Call
Record & Monitor check box.
6 Click OK.
The Telephone Groups list includes the new group.
Modifying a
Telephone Group
You may want to change the name of a telephone group to reflect a
change in your organization, or you may want to change whether the
group is configured for call recording and monitoring.
To change the name of a telephone group:
1 Click Telephone Configuration > Telephone Groups.
2 Click the group whose name you want to change.
3 Change the name of the telephone group in the Group Name field.
4 To set call recording and monitoring as the default condition for all
telephones in this telephone group, enable the Call Record & Monitor
check box.
You must install a call recording license before you can enable the Call
Record & Monitor check box.
5 Click OK.
Removing a
Telephone Group
You can remove a telephone group if you no longer need it.
To remove a telephone group:
1 Click Telephone Configuration > Telephone Groups.
2 Select the group, or groups you want to delete and click Remove
Selected. To select all groups, enable the Select check box.
3 Click OK when the system prompts you to remove the group.
Recording and Monitoring Telephone Calls
Viewing Telephone
Group Membership
111
You can view a report that describes to which telephone group a
telephone belongs. The report also includes membership information
about Class of Service groups.
To view the membership report, which includes information about all
telephone groups:
1 Click Telephone Configuration > Telephone Groups.
2 Click Membership.
3 Click any of the column headings to arrange the information in ascending
or descending order.
Recording and
Monitoring
Telephone Calls
If you have call recording application software that runs on a PC that is
external to the system, you can record and monitor telephone calls to and
from telephones on the system.
To enable call recording and monitoring on the system, you must
purchase a system-wide license. After you install the license, you can
enable call recording and monitoring for these devices:
■
Analog telephones connected to ports on an Analog Terminal Card or
to a single-port Analog Terminal Adapter
For instructions about how to enable these features, see:
■
■
“Adding an Analog Terminal Card” on page 126
■
“Adding an Analog Terminal Adapter (ATA)” on page 128
■
“Modifying an Analog Terminal Port” on page 129
3Com Telephones
For instructions about how to enable these features, see:
■
■
“Adding a New Telephone” on page 93
■
“Modifying a Telephone” on page 95
Telephone Groups
For instructions on enabling these features, see:
■
“Creating a New Telephone Group” on page 110
■
“Modifying a Telephone Group” on page 110
112
CHAPTER 5: TELEPHONE CONFIGURATION
Recording Calls
Between Telephones
with Different
Recording Settings
For a call that involves 3Com telephones or analog telephones that are
connected to either ATC ports or to ATAs, the system verifies the current
recording setting for each device to find out which recording setting to
use for the call.
Two-party Calls
In a two-party call involving only NBX devices, when you enable recording
on either device, the system enables recording for both devices for the
duration of the call. When the call has been completed, the system
restores the recording settings that were in effect prior to the call.
Conference Calls
If you enable recording on any NBX device in a conference call, the
system enables recording for all NBX devices for the duration of the
conference call. When the call has been completed, the system restores
the recording settings that were in effect prior to the call.
Example:
A three-party conference call involves these telephones:
■
A 3Com Business Telephone on the local system
■
An analog telephone connected to an ATC port on the local system
■
A 3Com Basic Telephone on a different system, connected to the local
system by a virtual tie line (VTL)
Only the 3Com Basic Telephone has recording enabled. For the duration
of the conference call, the system enables recording for the analog
telephone and the 3Com Business Telephone. After the call ends, the
system disables the recording for the analog telephone and the 3Com
Business Telephone.
Remote Telephones
Music On Hold (MOH)
If a 3Com telephone or an analog telephone connected to an ATA is
connected to a subnetwork different than the Call Processor’s, you can
enable recording for that remote device.
On an NBX system, MOH is always recordable. During a call with two
devices (3Com telephones, or analog telephones attached to ATC ports
or to ATAs) that both normally have recording disabled, if either person
puts the call on hold, the system enables recording while MOH is playing.
When the call is taken off hold, the system restores the recording settings
Creating and Managing Button Mappings
113
that were in effect prior to the call. If you disable MOH for the system,
recording is not enabled while the call is on hold.
The NBX system’s WAV file importing capabilities are solely an
accommodation to you and shall not constitute a grant or waiver (or
other limitation or implication) of any rights of the copyright owners in
any audio content, sound recording or underlying musical or literary
composition. Therefore, please be mindful that you are obligated to
comply with all applicable copyright and other intellectual property laws
in both uploading WAV files to the NBX system and your subsequent use
of such WAV files.
The MOH feature is available on Layer 2 devices only.
Non-3Com
Telephones
If your system has telephones other than 3Com Telephones attached, you
can include these telephones in 3Com telephone groups, provided that
the other telephones are configured to emulate a 3Com telephone.
CAUTION: If a telephone other than an 3Com Telephone is configured to
emulate an 3Com telephone, then you can add the telephone to the
associated telephone group (for example, the Default Business Phone
Group). However, the other telephone may only partially emulate an
3Com Business Telephone and may not respond to the commands to
enable or disable call recording. If you disable recording for the Default
Business Phone Group, it may still be possible to record calls involving the
telephones that are not 3Com Telephones in that group.
Creating and
Managing Button
Mappings
Button mappings allow you to place features, such as speed dial numbers
and shortcuts, on telephone buttons for individual telephones or for
telephone groups. In addition, you can use button mappings to map CO
telephone lines to buttons and set up your system in one of these modes:
■
Key Mode system — In Key Mode, all outside lines map to individual
buttons on users’ telephones. You can share lines by assigning one
line to multiple telephones. Incoming calls ring on all telephones that
have that line assigned. Any of those telephones can answer the call.
■
PBX (Private Branch eXchange) system — In a PBX system, outside
lines are pooled and arbitrated by the Call Processor. To call an outside
number, a telephone user must dial the line pool access number,
typically 9, and the Call Processor assigns the next available line.
114
CHAPTER 5: TELEPHONE CONFIGURATION
■
Hybrid Mode system — In hybrid mode, some lines are assigned as
keyed lines, while the rest are pooled.
You must use 3Com Business Telephones to operate the system in key
mode or hybrid mode. 3Com Basic Telephones operate in PBX mode only.
This section describes these topics:
Mapping Access
Buttons
■
Mapping Access Buttons
■
Mappings for Telephone Users and Groups
■
Creating a Busy Lamp/Speed Dial Button Mapping
■
Creating a Delayed Ringing Pattern
■
Creating Groups and Button Mappings
3Com Telephone access buttons have these characteristics:
■
3Com 3101 and 3101SP Basic Telephones each have four Access
buttons. Only two buttons can serve as line appearances, primary or
secondary bridged station appearances, or any other feature. You
cannot map the other two buttons as line appearances or primary
bridged station appearances, but you can map any other feature to
these buttons. These two buttons are mapped by default as Transfer
and Feature, and changing these default mappings can limit the
features you can access.
■
On 3Com 1102, 2102, and 1102-IR Business Telephones, you can
assign CO telephone lines or line pool access only to buttons that have
lights. You can assign one-touch actions such as Speed Dial or system
features such as Do Not Disturb to any access button.
■
3Com 2101 Basic Telephones include three access buttons. 3Com
2101 Basic Telephones operate in PBX mode only, that is, you cannot
map CO lines directly to telephone buttons.
■
Not all button type functions are available on all models of
telephones. Functions that you can assign to a button include Camp
On, Conference, WhisperPage, or Other, which lets you assign any
feature code to a button. For a description of each function you can
assign to a button, see the online Help.
■
The use of the Priority (priority) and Number fields depend on the
selected button type function.
Creating and Managing Button Mappings
Mappings for
Telephone Users and
Groups
115
■
The Ring field is used to enable and disable ringing for a lone
appearance button and to set delayed ringing patterns. See “Creating
a Delayed Ringing Pattern” on page 116 for more information.
■
A Lock check box at the Group Mappings level lets you control button
inheritance behavior. If you lock a button at the Group Mappings
level, a change made to the group always passes to every telephone in
the group. If you clear the Lock box at the Group Mappings level, you
can override the mapping at the device level. An icon at the device
level indicates whether the button can be remapped.
■
The check box Show caller ID on secondary bridged extensions when
on call appears on Button Mappings for the 3Com 3103 Manager’s
Telephone. This feature allows the device to display Caller IDs for
bridged extensions.
■
Telephone button mappings are part of a device. You assign a set of
mappings to an individual by associating a particular device or group
to the telephone user.
■
Telephone users can see the button mappings in effect for their
telephones by accessing the NBX NetSet interface with a personal
password.
■
Telephone users can use the NBX NetSet interface to create and print
labels for the access buttons on their telephones.
When you create a new telephone users and assign them to a group, the
button mappings for that group become active for the users’ telephones.
You can override group mappings and create mappings for individual
telephones. For example, you can create a group called Sales and assign
three shared direct lines to the group. Then you can assign one unshared
direct line to each of the telephones currently in use by members of the
Sales group.
The Lock feature (see “Creating Groups and Button Mappings” on
page 117) allows you to control button behavior. If you enable Lock, a
change that you make at the group level passes to every telephone in the
group and it cannot be overridden for individual telephones. If you
disable Lock, you can override group button mappings at the device level.
(This Lock feature is not the same as the Telephone Locking feature that a
telephone user can apply to an individual telephone. See an NBX
telephone guide for more information.)
116
CHAPTER 5: TELEPHONE CONFIGURATION
Creating a Busy
Lamp/Speed Dial
Button Mapping
A Busy Lamp/Speed Dial button is an access button, with a light, that is
mapped so that it can function as a speed dial to another extension and
also indicate when that extension is in use. When you press the access
button mapped to the Busy Lamp/Speed Dial button, you dial the
mapped extension. When the other extension is in use, the lamp lights on
your telephone.
For the Attendant Console, the Auto Discovery process creates a default
configuration that includes Busy Lamp/Speed Dial mappings for the first
100 extensions on the system.
A CO line mapped directly to telephones (Key mode) is not transferred to
any telephone user’s voice mail. For more information about key mode,
see Creating and Managing Button Mappings on page 113.
To create a Busy Lamp/Speed Dial button mapping:
1 Click Telephone Configuration > Telephones.
2 Click a telephone extension.
3 Click the Button Mapping tab.
4 Select an available Access button that has a light.
5 From the Type drop-down list, select Line/Extension.
6 From the Number drop-down list, specify the extension of the telephone
that you want as the Busy Lamp/Speed Dial target.
Creating a Delayed
Ringing Pattern
You can define a ringing progression for a line that you map to multiple
telephones. For example, you can configure a call to ring immediately at
telephone 1, begin ringing at telephone 2 after 4 rings, and then begin
ringing at telephone 3 after 8 rings. Any of the telephones can pick up
the call at any time, even if it has not yet started audibly ringing at a
particular telephone. (The light flashes during all rings.)
Delayed ringing works with Key mode only, that is, with line card ports
mapped to buttons on two or more telephones.
To create a delayed ringing pattern:
1 Use the Group Button Mappings feature of the NBX NetSet utility to map a
CO line. See Creating and Managing Button Mappings on page 113.
2 Set Ring to Yes.
3 Clear the Lock check box.
Creating and Managing Button Mappings
117
4 Click Telephone Configuration > Telephones.
5 Click the extension of the second telephone in the progression of
telephones where you want to create the Delayed Ringing pattern, and
then click the Button Mapping tab.
6 For the shared line appearance button, set the Ring box to the behavior
that you want.
For the telephone to begin ringing after one ring, select 1; after two
rings, select 2. Select No to disable ringing entirely. (The indicator light still
functions to indicate ringing/call status.) Do not change the settings in
the Type, Number, and Prty fields.
7 Repeat the procedure for each telephone in the Delayed Ringing pattern.
Set the Ring delay to create the appropriate delay for each extension.
Delayed Ringing Notes
Creating Groups and
Button Mappings
■
Delayed ringing is useful for backup coverage on shared lines, such as
for assistants who must cover each other’s lines.
■
The first telephone and each succeeding telephone in a delayed
ringing pattern continue to ring until the call is answered or
transferred to the Auto Attendant.
■
Telephones belonging to a delayed ringing pattern do not need to
belong to the same group. As long as all the telephones have the
same line mapped, you can create the delayed ringing pattern.
Telephone button mappings are part of a device. You assign a set of
mappings to an individual by associating a particular device or group to
that telephone user.
A telephone user can see the button mappings in effect for an assigned
telephone by logging on to the NBX NetSet utility with a personal
password. The telephone user can also use the NBX NetSet utility to
modify certain button mappings, and to create and print labels for the
access buttons on the telephone and set up One-Touch Speed Dials.
An administrator can define the button mappings for telephone groups
and also define exceptions to the group mappings for individual
telephones.
118
CHAPTER 5: TELEPHONE CONFIGURATION
To create groups and button mappings:
1 Click Telephone Configuration > Telephone Groups.
2 Click Add, type a Group Name, and click OK.
3 Click the telephone group name to which you want to apply mappings.
4 Click the Button Mapping tab.
5 See the online help for more information about how to configure the
button mappings.
To define button mappings for an individual telephone:
1 Click Telephone Configuration > Telephones.
2 Click the telephone extension to which you want to apply mappings.
3 Click the Button Mapping tab.
4 See the online help for more information about how to configure the
button mappings.
Changing Device IP
Settings
If you are using Standard IP network protocol, you can manually change
the IP address of telephones, Line Card ports, Attendant Consoles, and
Analog Terminal Cards. You modify the IP settings of a device if you plan
to move the device to a different subnetwork than that on which the Call
Processor resides. If a DHCP server serves the new subnetwork, the IP
address you assign to the device must be outside the address range that
the DHCP server uses.
You can install 3C10116D T1 and 3C10165D E1 Digital Line Cards in a
remote location and communicate with their Call Processors over a
routed network. For a description about how to configure remote Digital
Line Cards, see “Setting Up a Digital Line Card at a Remote Location” on
page 185.
See the online Help for more information about IP network protocols.
The BRI and ATC/ALC daughter cards on the 3C10164D-ST share the
same IP address. Therefore, depending on the configuration, you can
change the IP address following these paths:
■
Click PSTN Gateway Configuration> Digital Line Cards, click a MAC
address, and then click the IP Settings tab.
Changing Device IP Settings
■
119
Click Telephone Configuration > ATA, click an extension, and then
click the IP Settings tab.
If you change the IP Address for any of the daughter cards, the IP address
of the other daughter cards changes as well. You can use this method
only when the Call Processor and the 3C10164D-ST are located on the
same Ethernet segment.
To change the IP settings of a telephone:
1 Click Telephone Configuration > Telephones.
If you are updating the IP Settings of a different type of device (such as an
Attendant Console or a Digital Line Card), click the appropriate tab.
2 Click the extension of the telephone that you want to update.
3 Click the IP Settings tab.
4 Type the new values for IP Address, Subnet Mask, and Default Gateway
address in the fields.
5 Click OK.
6 Disconnect the device from the Call Processor subnetwork.
7 Connect the device to the new subnetwork as follows:
■
Connect a telephone or a single-port ATA to a port on either a switch
or hub that is connected to the new subnetwork.
■
Plug a card into a chassis that is connected to the new subnetwork.
8 Reboot the device:
■
Remove power from a telephone or a single-port ATA, and then
reconnect it.
If the device is a card, it reboots automatically when you insert it into
the new chassis. You do not need to remove power to the chassis
when you add or remove cards.
When you change IP Settings, the system terminates all current calls
through this device.
9 In the NBX NetSet utility, return to the IP Settings window for the device.
10 Verify that the device now reports the IP settings that you entered.
CAUTION: If you configure an 3Com telephone for operation on a
subnetwork other than the Call Processor’s subnetwork, and if you access
the IP Settings window to verify that the device settings are correct, click
Cancel to exit the window. If you click OK, the system applies the IP
120
CHAPTER 5: TELEPHONE CONFIGURATION
settings in the Manually Assigned IP Settings fields. By default, all these
fields contain 0.0.0.0. If you click OK, all the IP settings for the telephone
are set to 0.0.0.0, and the telephone no longer works on the remote
subnetwork.
Configuring the
3Com Attendant
Console
The 3Com Attendant Console provides extended button mappings and
displays the current status of each extension mapped to it. A receptionist
typically uses the Attendant Console to connect incoming calls to
telephone extensions.
This section describes how to configure the Attendant Console manually.
Alternatively, you can use Auto Discovery to add and configure the device
automatically, and then use the manual configuration procedures in this
section to fine-tune your mappings.
Before you autodiscover the Attendant Console, first autodiscover all
telephones, Analog Terminal Adapters, and Analog Terminal Cards. The
Auto Discovery process maps all existing telephones to the Attendant
Console.
You can associate any 3Com telephone with an Attendant Console.
However, if you use a 3Com 3103 Manager’s Telephone, you cannot map
a CO line directly to a button on the Attendant Console and the
Attendant Console will not support Bridged Station Appearances.
This section describes these topics:
Adding an Attendant
Console
■
Adding an Attendant Console
■
Modifying an Attendant Console
■
Viewing Attendant Console Status
■
Removing an Attendant Console
■
Configuring Attendant Console Buttons
■
Changing Attendant Console IP Settings
■
Configuring Connectivity to a 3105 Attendant Console Through the
Serial Port
Before you add Attendant Consoles, note the following requirements:
■
On a V3000, V3001, V3001R, or V5000 system, you can configure up
to 100 Attendant Consoles.
Configuring the 3Com Attendant Console
■
121
On an NBX 100 system, you can configure up to 50 Attendant
Consoles.
You can associate, at most, three Attendant Consoles with any one
telephone.
The 3Com 3105 Attendant Console requires a license. You must enter a
valid device license key into the NBX NetSet utility before you can add a
3Com 3105 Attendant Console to the system.
To add a new Attendant Console:
1 Click Telephone Configuration > Attendant Console.
2 Click Add.
3 Complete the fields and make the appropriate selections for the new
Attendant Console.
4 Click OK.
Modifying an
Attendant Console
You can change an Attendant Console’s device number or associated
telephone. You must associate every Attendant Console with a
telephone.
To modify an existing Attendant Console:
1 Click Telephone Configuration > Attendant Console.
2 Click the extension of the Attendant Console that you want to modify.
3 Modify the appropriate settings.
4 Click Apply to make the changes and then click OK.
Viewing Attendant
Console Status
From the Status window, you can view status information and also reboot
the Attendant Console.
To view the status of an Attendant Console:
1 Click Telephone Configuration > Attendant Console.
2 Select an Attendant Console extension.
3 Click the Status tab.
4 View the settings and optionally change the Dialog Refresh, Device
Refresh, and Reset Device settings. See the online Help for more
information about these fields.
122
CHAPTER 5: TELEPHONE CONFIGURATION
5 Click Apply to apply the settings.
Removing an
Attendant Console
To remove an Attendant Console from the system:
1 Click Telephone Configuration > Attendant Console.
2 Select the Attendant Console, or Attendant Consoles, that you want to
delete and click Remove Selected. To select all Attendant Consoles,
enable the Select check box.
3 Click OK in the dialog box to confirm.
Configuring
Attendant Console
Buttons
The Attendant Console buttons include:
■
50 Access buttons. You can assign two settings to each button.
■
The 3Com 1105 Attendant Console has five rows of ten buttons.
■
The 3Com 3105 Attendant Console has six rows for nine buttons.
■
A Shift button. This button switches between the two settings
allowed for each Access button.
■
Four Feature buttons.
Mapping Feature Buttons
To map the Attendant Console Feature Buttons:
1 Click Telephone Configuration > Attendant Console.
2 Click an Attendant Console extension.
3 Click the Feature Mapping tab.
4 Use the drop down list next to each button to select the feature you want
to assign to the button.
For a description of each function you can assign to a button, see the
online Help.
5 Click Apply for the changes to take effect.
Mapping the Attendant Console Access Buttons
To map the Attendant Console Access buttons:
1 Click Telephone Configuration > Attendant Console.
2 Click an Attendant Console extension.
3 Click the Button Mapping tab.
Configuring the 3Com Attendant Console
123
4 To map buttons, follow these steps:
a Click the 1-50 radio button to select:
■
Columns A through E on a 3Com 1105 Attendant Console
■
Columns A through F on a 3Com 3105 Attendant Console
b Click the 51-100 radio button to select:
■
Columns F through J on a 3Com 1105 Attendant Console
■
Columns G through L on a 3Com 3105 Attendant Console
This choice performs the same function as the Shift button on the
physical Attendant Console.
c Click the letter that corresponds to the column of buttons that you
want to map.
d Use the drop-down list boxes to map the buttons for the column that
you selected.
For a description of each function that you can assign to a button, see the
online Help.
5 Click Apply for the changes to take effect.
You cannot map an Analog Line Card or a primary bridged station
appearance to an Attendant Console button if that Attendant Console is
associated with a 3Com 3103 telephone. The 3Com 3103 Telephone
display can show a maximum of 12 calls only, and there is no way to
access any more calls at one time.
Changing Attendant
Console IP Settings
Although most configurations use IP On-the-Fly or DHCP to assign IP
addresses (and thus cannot manually change the addresses), if you use
Standard IP network protocol, you can manually change the IP address of
Attendant Consoles and other devices.
To set Attendant Console Feature IP settings:
1 Click Telephone Configuration > Attendant Console.
2 Click the extension of the Attendant Console
3 Click the IP Settings tab.
4 Type the new values for IP Address, Subnet Mask, and Default Gateway
address in the fields.
5 Click OK.
124
CHAPTER 5: TELEPHONE CONFIGURATION
When you change IP Settings, the system terminates all current calls
through this device.
Configuring
Connectivity to a
3105 Attendant
Console Through the
Serial Port
The 3Com 3105 Attendant Console supports manual configuration using
command line interface commands through the serial port on the
underside of the device. You can specify the device’s IP settings.
To connect the Attendant Console to a serial port on your computer
requires an adapter, such as the Kentrox DE9S to EIA-561 (RJ45 SOCKET)
ADAPTER MFR# 78909. Other manufacturers may offer appropriate
adapters. The adapter you choose must use the pinout configuration
shown in Table 23.
Table 23 Pinouts for 3105 Serial Connection
RJ45 pin
DB9 pin
Function
1
9
RI
2
1
DCD
3
4
DTR
4
5
GND
5
2
RXD
6
3
TXD
7
8
CTS
To connect a computer to the serial port on an Attendant Console:
1 Connect the DE9S to EIA-561 adapter to a serial port on the computer.
2 Connect a straight CAT5 cable (no crossover) from the RJ45 connector on
the adapter to the SERIAL 10101 port on the underside of the 3105
Attendant Console.
3 Start terminal-emulation software, such as HyperTerminal, on the
computer and create a new connection.
4 Configure the connection to use the settings in Table 24.
Table 24 Terminal-Emulation Program Properties
Property
Value
Emulation
VT100
Baud Rate
9600
Data bits
8
Configuring the 3Com Attendant Console
125
Table 24 Terminal-Emulation Program Properties (continued)
Property
Value
Parity
None
Stop bits
1
Flow control
None
5 Use the commands in Table 25 to configure the Attendant Console.
Specify IP and MAC address information appropriate for your network.
For 3C10405B model Attendant Consoles, you must include quotation
marks around the values
For example:
nbxSetIpAddress 192.168.123.123 (3C10405A model)
nbxSetNcpMacAddress “00:eo:bb:11:a1:b4” (3C10405B model)
The command line interface commands are case-sensitive.
Table 25 Command Line Interface Commands for Configuring the 3105 Attendant Console
Parameter
Command Line Interface Command*
Comment
Configuration nbxShowConfig
Shows the device and system configuration.
Device IP
Address
nbxSetIpAddress <nnn.nnn.nnn.nnn>
Sets the IP address of the device. You clear
the address if you set the IP address to
0.0.0.0 or 255.255.255.255.
Subnet
Mask
nbxSetSubnetMask <nnn.nnn.nnn.nnn>
Sets the IP subnet mask for the device.
Default
Gateway
nbxSetGatewayAddress <nnn.nnn.nnn.nnn>
Sets the IP address of the device’s default
gateway. You clear the address if you set
the IP address to 0.0.0.0 or
255.255.255.255.
Call Processor nbxSetNcpIpAddress <nnn.nnn.nnn.nnn>
IP Address
Sets the IP address of the device’s Call
Processor. You clear the address if you set
the IP address to 0.0.0.0 or
255.255.255.255.
Call Processor nbxSetNcpMacAddress <##:##:##:##:##:##> Sets the MAC address of the device’s Call
MAC Address
Processor. You clear the address if you set
the MAC address to ff:ff:ff:ff:ff:ff.
* FOr 3C10405B model Attendant Consoles, you must include quotation marks around the values.
You must also use the NBX NetSet utility to add the device to the system
database.
126
CHAPTER 5: TELEPHONE CONFIGURATION
Connecting and
Managing Analog
Devices
An Analog Terminal Card (ATC) or an Analog Terminal Adapter (ATA)
allows ordinary analog (2500-series compliant) telephones, including
cordless telephones and Group-3 facsimile (fax) machines, to operate
with NBX systems.
These limitations apply because of the differences between an analog
device and a 3Com Telephone:
■
A telephone user dials 500, then ** on a telephone connected to an
ATA to gain access to voice mail.
■
An analog telephone can make or receive only one call. The system
forwards a second incoming call to voice mail.
This section discusses these topics:
Adding an Analog
Terminal Card
■
Adding an Analog Terminal Card
■
Adding an Analog Terminal Adapter (ATA)
■
Modifying an Analog Terminal Port
■
Removing an Analog Terminal Adapter
■
Viewing The Status of an Analog Terminal Adapter
To add an Analog Terminal Card to the system using Auto Discovery:
1 Click System-Wide Settings > Auto Discovery.
2 Click the Auto Discover Other Devices (including ATA, Digital Line Cards &
Analog Line Cards) check box.
3 Click Apply.
4 Insert the Analog Terminal Card into the chassis.
5 Wait approximately 1 minute for the system to discover the card.
6 Click Telephone Configuration > ATA.
The four ports of the Analog Terminal Card appear in the ATA list, as well
as the ports of any previously discovered Analog Terminal Cards and any
previously discovered Single-Port Analog Terminal Adapters (ATAs).
Connecting and Managing Analog Devices
127
Extension Assignments (3C10117 ATC)
The 3C10117C Analog Terminal Card replaces the 3C10117 Analog
Terminal Card.
Each of the four ports on a 3C10117 Analog Terminal Card has a MAC
address. The first port has the same MAC address as the card, and the
remaining three ports have sequential MAC addresses incremented by
one hexadecimal digit. See Table 26:
Table 26 MAC Addresses of Analog Terminal Card Ports (3C10117)
Card or Port
MAC Address
Analog Terminal Card
00:e0:bb:00:f8:c8
Port 1
00:e0:bb:00:f8:c8
Port 2
00:e0:bb:00:f8:c9
Port 3
00:e0:bb:00:f8:ca
Port 4
00:e0:bb:00:f8:cb
The extensions that the system assigned to these ports may not be in
order. For example, if the system assigns extensions 7258, 7259, 7260,
and 7261 to the ATC ports, it may assign 7258 to port 3.
To find out which extension is associated with a given port, click
Telephone Configuration > ATA and examine the list of ATAs and ATC
ports. For example, to find out the extension that is assigned to the third
port, look for the ATC port with a MAC address that is two hexadecimal
digits higher than the MAC address of the board. The extension of the
port is in the first column (Extension).
After you add the Analog Terminal Card, you can configure the
parameters for each of the four ports. See “Modifying an Analog
Terminal Port” on page 129.
Extension Assignments (3C10117C ATC)
On a 3C10117C Analog Terminal Card, there is only one MAC address.
Each of the four ports is assigned a unique virtual device number
(1 through 4) so that the system software can address each port
separately.
128
CHAPTER 5: TELEPHONE CONFIGURATION
When you click Telephone Configuration > ATA to view the information,
the system displays the port number, enclosed within square brackets,
after the MAC address. See Table 27.
Table 27 MAC Addresses of Analog Terminal Card Ports (3C10117C)
Card or Port
MAC Address
Analog Terminal Card
00:e0:bb:00:f8:c8
Port 1
00:e0:bb:00:f8:c8[1]
Port 2
00:e0:bb:00:f8:c8[2]
Port 3
00:e0:bb:00:f8:c8[3]
Port 4
00:e0:bb:00:f8:c8[4]
The extensions that are assigned to these ports by the system may not be
in order. For example, if the system assigns extensions 7258, 7259, 7260,
and 7261 to the ATC ports, it may assign 7258 to port 3.
To find out the extension that is assigned to any port on a 3C10117C
ATC:
1 Click Telephone Configuration > ATA.
2 Look for the combination of MAC address and port number that you
want. The extension associated with the port is in the first column
(Extension).
After you have added the Analog Terminal Card, you can configure the
parameters for each of the four ports. See “Modifying an Analog
Terminal Port” on page 129.
Adding an Analog
Terminal Adapter
(ATA)
To add an Analog Terminal Adapter (ATA) to the system:
1 Click Telephone Configuration > ATA.
2 Click Add.
3 Complete the fields, as necessary. See the online Help for more
information.
4 Click Apply to add the new ATA to the system.
5 Repeat as necessary to add more ATAs.
6 When you are finished adding ATAs, click OK.
Connecting and Managing Analog Devices
Modifying an Analog
Terminal Port
129
You can modify the configuration of an Analog Terminal Card port or a
single-port ATA at any time.
To modify an analog device configuration:
1 Click Telephone Configuration > ATA.
2 Click the extension of the device that you want to modify.
3 Modify the fields, as necessary. See the online Help for more information.
4 Click Apply to effect the changes.
5 Click OK.
Removing an Analog
Terminal Adapter
You can remove either an Analog Terminal Adapter (ATA) or one of the
ports on an Analog Terminal Card (ATC) from the system at any time. Any
device connected to the ATA is also removed from the system.
To remove an ATA or ATC port:
1 Click Telephone Configuration > ATA.
Use the MAC addresses to find out if an item in the list is an Analog
Terminal Adapter (ATA) or one of the ports on an Analog Terminal Card.
Ports on a 3C10117 Analog Terminal Card have MAC addresses that
differ by two hexadecimal digits. Ports on a 3C10117C Analog Terminal
Card all have the same MAC address and use a Virtual Device Number to
identify each port. The system displays a port number, enclosed in square
bracket, after the MAC address. An ATA has a unique MAC address with
no port number.
2 Select the ATA or ATC port that you want to delete and click Remove
Selected. To select all ATAs or ports, enable the Select check box.
3 Click Remove Selected.
Viewing The Status
of an Analog
Terminal Adapter
You can view the status of either an ATA or one of the ports on an ATC at
any time.
To view the status of an ATA or an ATC port:
1 Click Telephone Configuration > ATA.
Use the MAC addresses to find out if an item in the list is an ATA or one
of the ports on an ATC. Ports on a 3C10114 Analog Terminal Card have
sequential MAC addresses. Ports on a 3C10114C Analog Terminal Card
130
CHAPTER 5: TELEPHONE CONFIGURATION
all have the same MAC address followed by a Virtual Device Number
(VDN), enclosed in square brackets. An Analog Terminal Adapter has a
unique MAC address with no port number.
2 Click the extension of an ATA or ATC port.
3 Click the Status tab.
4 View the device status and make any necessary changes. See the online
Help for more information.
5 Optionally, to send a status message to the Call Processor about the ATA
or ATC port, click Refresh Device.
6 Optionally, to reset the ATA or ATC port, click Reset Device and click OK
when the system prompts you confirm.
CAUTION: On the 3C10114 Analog Terminal Card, you can reboot
individual ports without affecting the other ports. However, if you reboot
a port on the 3C10114C Analog Terminal Card, all four ports on the card
reboot, which disrupts active calls on any of these ports.
7 Click OK.
Advanced Settings
You can set the audio gain and timing controls on an ATA or each port of
an ATC. To set these parameters:
1 Click Telephone Configuration > ATA.
2 Click the extension of an ATA or ATC port.
3 Click the Advanced Settings tab. See the online Help for more
information.
If you change any of the values in the Advanced Settings dialog box, the
settings you change persist if you later upgrade the system software or
you change the regional software.
6
USER CONFIGURATION
This chapter describes these elements of the system:
■
Users
■
Phantom Mailboxes
■
Class of Service (CoS)
For more information about these topics and configuration procedures,
see the online Help.
Users
You use the Users window in the NBX NetSet utility to add telephone
users and remove them from the system. You can also modify and
maintain user profiles and parameters.
To perform these tasks:
1 Click User Configuration > Users.
To add a SIP telephone to a SIP-mode system, you must first add a SIP
telephone user and extension to the system database, and then use the
SIP telephone to complete the configuration.
2 See the online Help for information about how to add, modify, and
remove telephone user settings, and about SIP telephones.
For information about user settings that individual telephone users can
configure, see Chapter 1 in an NBX telephone guide.
Phantom Mailboxes
A phantom mailbox is an extension that has no associated physical
telephone. A caller can dial directly into a phantom mailbox and leave a
message. The person assigned to a phantom mailbox can create and
send a message from within the voice mail system and the Auto
Attendant can route callers to a phantom mailbox.
132
CHAPTER 6: USER CONFIGURATION
Example: A telephone user who is never in the office can use a phantom
mailbox to receive and manage messages, even though no telephone is
associated with the mailbox extension. The telephone user can call into
voice mail to retrieve and send messages, log onto the NBX NetSet utility
to manage messages, including having the system forward voice
messages using the Off-Site Notification feature, or use an e-mail client to
manage the messages. See “IMAP for Integrated Voice Mail” in
Chapter 9.
To create a phantom mailbox:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click User Configuration > Users.
3 See the online Help for information about how to add, modify, and
remove phantom mailboxes.
To access a phantom mailbox from any telephone, the telephone user:
1 Calls the extension.
2 Presses * during the greeting.
3 Logs in.
4 Provides mailbox initiation information when the system prompts, if this is
the first time the phantom mailbox is accessed.
5 Use the NBX NetSet utility to set up telephone options, such as Call
Forwarding, after setting up a password.
Class of Service
(CoS)
Class of Service (CoS) is a set of calling permissions that you assign to
telephone users. Most permissions are subject to the Business Hours
parameters: Open, Lunch, and Other. For example, you can create a class
that allows toll calls during normal business hours, but denies them at
other times. You can control if the telephone user can use certain
features, such as mapping features to buttons on the telephone or
preventing a call from being monitored.
To configure CoS:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click User Configuration > Class of Service.
Class of Service (CoS)
133
3 See the online Help for information about how to add, modify, remove,
and view Class of Service.
Note the following considerations:
■
Emergency calls (such as calls to 911) are not subject to CoS
restrictions.
■
System-wide Speed Dial numbers are not subject to Class of Service
restrictions. For example, if you want to enable calling to a specific toll
number to all telephone users without regard to their CoS settings,
create a System Speed Dial for that number.
■
When you create a new profile, the system assigns the default CoS
unless you specify a different one. If you edit the properties of the
default CoS, verify that it contains a minimum set of permissions.
■
You can enable or disable Off-site Notification at the system level. The
system-wide setting takes precedence over the CoS setting.
■
A telephone user can override the CoS of a telephone by using feature
code 433. For example, a telephone user with an assigned office
telephone that allows calls to external numbers needs to place a call
to an external number from a conference room telephone with a CoS
that does not allow external calls. The telephone user enters the
feature code into the conference room phone, and the system
prompts for username and password before allowing the call. The
feature code applies to the next call only. After the telephone user
hangs up, the telephone reverts to its assigned CoS.
■
To set an account code as Forced, enable the Force Acct Code check
box for each appropriate Class of Service (click User Configuration >
Class of Service, and then click an extension or Add).
Verifying account codes is a global configuration setting, while
enforcing account codes is a CoS function. If the CoS setting enforces
the account code for that type of call, a telephone user must enter an
account code before the system routes the call.
■
You can allow telephone users to configure button mappings on their
own devices. Enable User Button Mappings when you add or modify a
group’s CoS settings. If you enable this feature, when the individual
telephone user clicks Telephone Programming in the NBX NetSet
utility, the system displays the Button Mapping tab, which enables the
telephone user to map functions to telephone buttons. If you do not
enable this feature, the system does not display the Button Mapping
tab.
134
CHAPTER 6: USER CONFIGURATION
■
If you allow telephone users to configure button mappings on their
own devices, a telephone user can override any button mappings that
you set unless you lock the button to prevent changes. To lock a
button and prevent telephone users from mapping a function to that
button, click Telephone Configuration > Telephone Groups. Select the
appropriate telephone group and click the Button Mappings tab.
Enable the Lock check box next to the appropriate button and click
Apply.
■
CoS permissions do not apply to hunt groups. This means a CoS
cannot prevent you from configuring operators in a Hunt Group.
Service classes control these types of calls:
■
Intercom
■
External (local, long distance, international, long distance toll-free,
and long distance toll)
■
CO Code (optional telephone company services, such as Call Waiting)
■
Trunk to trunk transfers
■
Off-site Notification
■
Configurable operators (destinations pre-selected by the user to which
callers are sent if those callers reach the telephone user’s voice mail)
7
CALL DISTRIBUTION GROUPS
Call distribution groups allow for the distribution of incoming calls to the
appropriate agent without any specific action on the part of that agent.
The system supports two kinds of call distribution groups:
■
A hunt group is a set of telephone users that you can access when you
dial a single extension
■
An Automatic Call Distribution, or ACD, group is similar in concept
and practice to a hunt group. However, an ACD group includes other
features, such as database capabilities, that are specifically suited to
call center operations.
Topics in this chapter include:
■
Automatic Call Distribution (ACD)
■
ACD Considerations
■
Using ACD
■
Hunt Groups
For more information about these topics and configuration procedures,
see the online Help.
Automatic Call
Distribution (ACD)
A call center is the general term that refers to any system that accepts
incoming calls to a site, ensures that those calls are sent to the proper
destination within the site, and manages database records on call activity
and distribution. For example, you can use the call center as a help desk,
a reservations counter, an information hotline, or a customer service
center. A telephone call center typically manages collections of telephone
extensions that are linked to a centralized database.
The ACD distributes calls to agents and queues the calls that have not
been answered before a pre-determined time period expires. The ACD
136
CHAPTER 7: CALL DISTRIBUTION GROUPS
also manages recorded announcements to callers, manages individual
ACD agents and groups of agents, and provides database reports about
both calls and agents.
The Call Pickup feature is supported for ACD groups.
Topics in this section include:
■
ACD Groups
■
ACD Shifts
■
Estimated Wait Time Announcements
■
In-Queue Digit Processing and Announcements
■
ACD Group Open/Close and Announcements
■
Announcements for SIP-Mode Systems
■
Wrap-Up Time
■
Streaming ACD Data Through a TCP Socket
See the administrator online Help for configuration instructions.
ACD Groups
To take full advantage of ACD, organize your ACD agents into ACD
groups. An ACD group is a number of agents that the system treats as a
single entity for the purposes of handling calls.
■
Supported ACD Group Types
■
Multiple ACD Group Membership
■
ACD Agent List
■
ACD Licenses
■
ACD Group Populations
Supported ACD Group Types
The system supports the following ACD group types:
■
ACD Linear Group
The system can distribute calls to the group in a linear fashion. An
incoming call goes to the agent ranked first and, if the agent is not
available, then to the agent ranked second. The process continues in
this way until the system completes the rankings, at which point the
call cycles to top of the rankings list to begin again.
Automatic Call Distribution (ACD)
■
137
ACD Circular Group
The system can distribute calls to the group in a circular fashion. The
system attempts to place an incoming call with the agent whose rank
follows the agent that received the last call. If this agent is not
available, the call goes to the next ranking agent. If the second agent
is not available, the system from that point on treats the call as linear.
■
ACD Most Idle Agent Group (MIA)
The system can distribute calls to the group on the basis of idle time;
that is, the system directs the call to the agent who has been idle for
the longest amount of time, then to the agent that has been idle the
next, longest amount of time. If the second agent does not answer
the call, the system then treats the call as linear.
■
ACD Least Call Count
Least Call Count mode distributes calls to ACD agents based on the
number of calls that those agents have answered in a defined period
of time.
In other words, the agent with the least number of answered calls for
a given duration of time becomes the next available agent. For
example, two agents in a group each have been logged in to their
ACD group for ten minutes. Agent One, has answered five calls and
Agent Two has answered ten calls. In this case, the system assigns
Agent One to receive the next incoming call.
All types provide a timeout value that defines final call handling, such
as voice mail or Auto Attendant, if the timeout value is exceeded.
■
Calling Groups
A Calling Group is an ACD group in which a single call alerts or rings
all member telephones. In this case, all the telephones in a Calling
Group continue to ring until a member answers the call, or until the
Total Timeout value is reached.
The practical effects of this behavior are as follows:
■
■
■
The Per-device Timeout applies to every device in a Calling Group.
A Calling Group call alerts an agent's telephone that is busy or on
another call once, then blinks on one of the System Appearance
lines.
The system does not alert logged-out members.
138
CHAPTER 7: CALL DISTRIBUTION GROUPS
■
■
■
■
Only one call is served out to the ACD queue. The other calls must
wait to be served or routed to call coverage until after the Total
Timeout value has been reached.
If all Calling Group members are logged out, the system forwards
the call to call coverage immediately.
If there are no current members in the Calling Group, the system
forwards the call immediately to the call coverage path.
You cannot configure the system to log out an agent that does not
answer automatically.
Multiple ACD Group Membership
If any agent is a member of more than one ACD group, the system tracks
requirements such as Least Call Count and Most Idle Agent so that these
requirements are taken into account when calls are routed to that agent.
For example, Agent One is a member of two ACD groups. Agent One's
call count reflects the total of calls received from both groups, so Agent
One’s idle time reflects the total for calls that come from both groups. The
system routes calls to Agent One based on this calculation.
You can use this feature to allow agents with different skill sets to be a
part of multiple ACD groups.
ACD Agent List
Both ACDs and hunt groups act upon a list of selected extensions rather
than the entire directory of telephone extensions on the system. In the
case of ACD, the supervisor creates this list, called an Agent list.
The system does not support bridged station appearance behavior for
ACD agents. When a bridged station appearance is added as an agent to
an ACD group, the system routes incoming ACD group calls to the
primary telephone only.
ACD Licenses
A software license defines the number of agents that you can add to the
Agent list. The Base License key for ACD allows two agents. You can
purchase an additional license that authorizes three more agents, for a
total of five agents. Thereafter, you must purchase licenses to add agents
by increments of five agents.
Automatic Call Distribution (ACD)
139
You can configure a maximum of 200 ACD agents for each system.
ACD Group Populations
ACD administrators typically organize agents whose functions are
logically related into entities called ACD groups. These groups can be
used instead or with the ACD Agent List while creating (or modifying) the
ACDs. ACD groups can be added as members of the ACD along with the
individual extensions from the ACD Agent List.
ACD Shifts
ACD can provide different kinds of work shifts for ACD agents. As well as
managing calls, ACD shifts can differentiate work assignments in the
Real-Time Streaming Statistics, and to reset internal statistics used by the
Most Idle Agent and Least Call Count call distribution methods.
The ACD shift feature is not available on SIP mode systems.
You can set up an ACD group to have any one of the following shifts:
■
24-hour shift – The ACD group always accepts incoming calls. This is
the default behavior.
■
Shift that uses system business hours – The ACD group uses
defined business hours (click System-Wide Settings > Business Hours).
■
One of four custom configurable shifts – The ACD group uses the
hours specified in the ACD function Custom Hours.
■
Dynamic or Emergency Shifts – The operating hours of the ACD
group are dynamically reset in the ACD function Custom Hours.
Custom Operating Hours and Shifts
ACD includes the concept of customizable work shifts. You plan your
ACD call coverage at your site that best suits the call center. As the basis
for this discussion, click Call Distribution Groups > ACD Groups. Then,
click an extension or Add, and click the Custom Hours tab.
The Start time of a shift is the End time of its predecessor. However, you
do need to specify the Start time and End Time for each appropriate day
because this is what defines the operating boundaries of the ACD for
that day.
■
Shift 1 is mandatory, and represents the start of operations.
140
CHAPTER 7: CALL DISTRIBUTION GROUPS
■
Shifts 2,3 and 4 are optional, and you need only enter the Start time
for those shifts.
The system routes any call to the ACD within the operating hours to its
agents. Any call that arrives outside the ACD operating hours generates a
Closed announcement, and the system forwards the call to preconfigured
call coverage.
Dynamic or Emergency Shifts
If an ACD is closed, you can force it into an Open state to accept calls
during an emergency (click Call Distribution Groups > ACD Groups and
then click Open/Close).
Designate the start of shift as the time of the Force Open action. All
statistics for Least Call Count and MIA begin from this Force Open Start
time. The End time for this dynamic or emergency shift is either the Start
time of the next shift or the Force Close time, whichever happens first.
Estimated Wait Time
Announcements
You can configure the system to provide recorded announcements that
inform a caller approximately how long it will be before an agent answers
the call. This time interval is called estimated wait time. You can choose
to have the caller hear an Estimated Wait Time announcement by itself or
following a Delayed announcement.
For example, you can record a Delayed announcement such as “An agent
will take your call soon” that is followed by an Estimated Wait Time
announcement, which might announce “Your estimated wait time is two
minutes.”
To configure the system to play Estimated Wait Time announcements and
set Estimated Wait Time settings, click Call Distribution Groups > ACD
Groups, click an extension or Add, and then click the Announcements
tab. See the online help for more information.
SIP-mode systems do not support Estimated Wait Time announcements.
The system uses this formula to calculate Estimated Wait Time:
Minimum Wait Time + Estimated Average Call Duration * (Caller’s current
queue position -1)/(max(Number of logged in agents who are
idle,Minimum Agents logged in))
Automatic Call Distribution (ACD)
141
You set these variables in the formula from the NetSet utility:
■
Minimum Agents logged in
■
Estimated Average Call Duration
■
Minimum Wait Time
The remaining variables in the formula, such as the caller’s queue position
or the number of agents that are logged in, are dynamic. The system uses
both the dynamic and the configurable variables to calculate the
Estimated Wait Time in real time.
For example, you might set the configurable variables as:
■
Minimum Agents logged in = 0
■
Estimated Average Call Duration = 75 seconds
■
Minimum Wait Time = 40 seconds
If three callers call into an empty queue in rapid succession, and two
agents are logged in but neither agent answers the calls:
■
The first caller hears an announcement for an estimated wait time of 1
minute.
■
The second caller hears an announcement for an estimated wait time
of 2 minutes.
■
The third caller hears an announcement for an estimated wait time of
4 minutes.
The minimum estimated wait time is never less than 1 minute. That is, the
first caller will always hear an announcement for an estimated wait time
of 1 minute or more.
If you change the configurable variables, the system calculates a new
estimated wait time. For example, if you change the Estimated Average
Call Duration from 75 seconds to 300 seconds:
■
The first caller hears an announcement for an estimated wait time of 1
minute.
■
The second caller hears an announcement for an estimated wait time
of 6 minutes.
142
CHAPTER 7: CALL DISTRIBUTION GROUPS
■
The third caller hears an announcement for an estimated wait time of
11 minutes.
Adjust the Estimated Wait Time settings to reflect the actual average call
duration for your environment.
In-Queue Digit
Processing and
Announcements
While a call is in the ACD queue, the calling party can press a digit to
force the system to take the call off the queue and forward it to the Call
Coverage path. You configure this In-Queue Digit Hot Key in the
Announcements window. (The default digit is '#'.)
The Call Coverage path can be one of the following:
■
Call coverage path of the ACD group itself (default)
■
Auto Attendant
■
ACD Voice Mailbox
■
Another extension (another ACD, Hunt Group, internal extension,
extension over VTL, or external number)
Make the caller aware of this ability to break out of the call queue by
recording an in-queue digit announcement, then designating the .WAV
file as such in the In-Queue Digit Announcements section of the
Announcements window.
SIP-mode systems do not support In-Queue Digit processing (including its
associated announcements).
ACD Group
Open/Close and
Announcements
An ACD Group is considered Closed at any time other than the
configured shifts (business hours). However, you can provide an
announcement (using the Announcements window) that provides the
reason why the ACD group is closed. The system then forwards the call to
Call Coverage, using the same path as that designated in Group Time
Out.
You can force the Close state (click Call Distribution Groups > ACD
Groups and then click Open/Close) of any ACD Group for a holiday or
emergency. You must manually enable the first thing on the next working
day. Any new calls after the force close receive an ACD close
announcement and the system forwards them to call coverage. In case of
a force open, the ACD closes at the next configured close time.
Automatic Call Distribution (ACD)
Announcements for
SIP-Mode Systems
143
A SIP-mode system uses a different audio codec format than a system
that uses 3Com call control. If you are running in SIP mode, you must use
an IP messaging server (such as the 3Com IP Messaging Server) instead of
NBX Voice Mail Messaging.
SIP-mode systems do not support Estimated Wait-Time announcements
or In-Queue Digit Processing.
Wrap-Up Time
Wrap-Up Time is the time interval needed by an agent in this ACD group
to take notes on or follow up a completed call. During Wrap-Up Time,
the system routes no calls to the agent except personal calls or Calling
Group calls.
The timer value is specified in seconds, and the Wrap-Up timer engages
after the agent completes the ACD call. The display panel or status light
on the agent’s telephone indicates that Wrap-Up Time is engaged. After
Wrap-Up-Time expires, the agent becomes available to take new calls,
and the display panel or status light deactivates.
You can set the Wrap-Up timer value between 0 and 999 seconds. A zero
value (default) signifies that Wrap-Up Time is not configured.
SIP-mode systems do not support the Wrap-Up Time feature.
Wrap-Up Time Indicators
The status light associated with the button mapped for Wrap-Up Time
lights up while the agent is in Wrap-Up mode. This status light turns off
after Wrap-Up time is complete, or when the agent overrides it.
In addition to the status light, the display panel displays Wrap Up during
the time allotted, then returns to the default display after the Wrap-up
time is complete, or when the agent overrides it.
Wrap-Up Time Agent Override
Feature code 972, or a mapped button, allows the agent to override the
Wrap-Up timer to take new calls immediately.
However, the agent can override the Wrap-Up timer only after
completing the call. This means that even if the agent wants to override
Wrap-Up time during an ACD call to take another ACD call, the agent
144
CHAPTER 7: CALL DISTRIBUTION GROUPS
cannot do so. The only exceptions to this rule are personal calls or Calling
Group calls.
Therefore, if an agent is part of two ACD Groups, the agent cannot
receive calls from either group if Wrap-Up Time has engaged after an
ACD call from either group. After the timer expires and the agent takes a
call from the second ACD group, closing this call starts the Wrap-Up
Timer from the second ACD group, which the agent can override.
Wrap-Up Time Agent Extend
Agents who need extra Wrap-Up time can map another button, or use
Feature Code 973 to extend this time. The agent can only extend while
Wrap-Up time is active; once the Wrap-Up time expires, the agent cannot
extend the wrap-up time. An agent can extend Wrap-Up time one
instance by default.
Streaming ACD Data
Through a TCP Socket
You can use the NBX NetSet utility to enable one TCP port to stream ACD
data from the system to an external device for further analysis. (The NBX
ACD Desktop Statistics Application from 3Com provides the client-side
support for this data streaming. See your 3Com NBX Voice-Authorized
Partner for details.)
NBX 100 systems do not support streaming ACD data.
Any number of ACD groups can share this port. The data can be enclosed
in XML tags to facilitate parsing at the client side or, alternatively, can be
streamed in pure text or ASCII format as name value pairs. This data
stream contains detailed data for all of the ACD groups and their agents.
ACD Considerations
Note these restrictions before you configure ACD operations on your site.
■
Hardware Limits for ACD Groups
■
ACD Operations With Call Detail Reports (CDR)
■
Display Data
■
Voice Mail Port Usage
ACD Considerations
Hardware Limits for
ACD Groups
145
Table 28 lists the limits on the number of ACD groups for each hardware
platform:
Table 28 ACD Group Limits
Systems
Limit
V3001 (256 MB)
Up to 48 concurrent ACD groups
V3000 (128 MB)
NBX 100
V3001R
Up to 100 concurrent ACD groups
V3001 (512 MB)
V3000 (640 MB)
V5000
ACD Operations With
Call Detail Reports
(CDR)
The Call Detail Reports application creates a Microsoft Access database
for the data that it extracts from the system. This database has only one
table, and all data is put into this table.
For ACD calls, the CDR application puts all call data into a new, second
table. The fields in this table differ from the other table and, therefore,
provide more details about the ACD calls.
The ACD group table data is accessible by CDR, but hunt groups do not
have this table.
ACD reports in the CDR Application
The CDR client application has been modified to give you the option of
viewing the new table for the ACD groups. Also, CDR provides
pre-defined reports for ACD groups that ACD supervisors are able to use
for performance evaluation.
Display Data
Voice Mail Port Usage
The ACD windows do not refresh themselves, you must manually refresh
the window to see the latest data.
On a system with NBX Voice Messaging enabled, ACD announcements
use system voice mail ports. The following platform limitations for voice
mail ports apply:
■
72 voice mail ports (V3001R, V3001 (512 MB), V3000 (640 MB), and
V5000 systems)
146
CHAPTER 7: CALL DISTRIBUTION GROUPS
■
12 voice mail ports (NBX 100, V3001 (256 MB), V3000 (128 MB)
systems)
See the section “Contention” on page 152 for more information about
resource limitations for delayed announcements.
Using ACD
First, decide the scope of your call center operations. Then ensure that
you have the system resources that you need:
■
Less than the allowable maximum of devices on the system
■
Sufficient number of voice mail ports
■
Sufficient number of ACD licenses (one for each agent)
Next, allot the agents into ACD groups, and decide how many agents
within each group that you need. Once you reach the point where your
call center planning is complete, you can begin to configure ACD
operations.
The ACD user interface is set up such that you can configure ACD as
soon as your planning is complete. Click Add in ACD Groups window to
configure each group. This button invokes a configuration utility that
leads you through the configuration process: defining ACD group
characteristics, identifying group agents, defining announcements for the
group, and summarizing the group creation process.
After you have set up the ACD group or groups, you can configure other
settings to assist their operation, including feature mappings and
Supervisory Monitoring Domains (Feature Settings > Supervisory
Monitoring). You can also modify your configuration settings.
ACD Groups
The ACD Groups feature allows you to configure the relationship
between agents and groups.
The following sections provide information about the fields and buttons
in the ACD Groups window (Click Call Distribution Groups > ACD
Groups).
Display Fields in the ACD Groups Window
Table 29 describes what each display field shows in the ACD Groups
window.
Using ACD
147
Table 29 ACD Groups window: Field Description
Field
Description
Extension
Lists the extension that the administrator assigned to this
ACD group.
Name
Lists the name that the administrator assigned to this ACD
group.
Method
Shows the call distribution method that the administrator
assigned to this ACD group. Types include:
■
Linear
■
Circular
■
Most Idle Agent
■
Least Call Count
■
Calling Group
Members
Shows the number of extensions associated with this ACD
group.
State
Whether the group is Open or Closed.
Functions on the ACD Groups Window
The ACD Groups window allows you to configure the operating
environment of the ACD groups at your site. You can perform specific
group-related tasks, such as adding a group, modifying a group
password, or removing an agent from a group.
Table 30 describes the functions that you can access from the ACD
Groups window.
Table 30 Function on the ACD Groups Window
Function
Description
Add
Invokes a multi-step configuration utility that helps you
create a new ACD group.
Modify
Click a Group Extension to change the configuration
parameters of an existing ACD group.
Memberships
Lists the data of agents in a specific ACD group
Announcements
Provides the means to add, change, remove and list the
audio files used for the recorded greetings in an ACD
group.
Remove
Deletes an existing ACD group.
Status
Provides a snapshot report of a selected ACD group.
148
CHAPTER 7: CALL DISTRIBUTION GROUPS
Table 30 Function on the ACD Groups Window
Function
Description
Feature Mappings
Provides the means to list or change the feature codes
mapped to ACD extensions.
Supervisory Monitoring Configures the settings for Supervisory Monitoring, a
facility that allows a supervisor to monitor calls to agents.
See “Supervisory Monitoring” on page 53 for more
information.
Off-Site Notification
Allows you to forward calls to specific telephone numbers
outside the ACD facility.
NOTE: SIP-mode systems do not support Off-Site
Notification.
For more information about the configuration procedure, see the online
Help.
ACD Announcements
ACD plays audio announcements to parties that call the ACD site. You
create or import these announcements as .WAV files so that callers
waiting to speak to an ACD agent hear an audio message of your choice.
You can configure up to five different ACD announcements for each ACD
group.
ACD announcements work for ACD groups only; hunt groups do not
have this feature. For SIP-mode systems, you must configure ACD
Announcements through the IP Messaging Service. See Chapter 10 for
more information.
Announcement Sequence
The system plays the first announcement file after the caller has been in
the queue for the time delay specified in the Time Interval field (Click
Call Distribution Groups > ACD Groups, click an extension or Add, and
then click the Announcements tab).
The system plays the remaining files as the time interval for each file
expires (assuming the caller is still in the ACD queue waiting to be
connected to an agent). This means that you can set up the sequence in
which announcements are played, with a predefined time delay between
them, to engage the caller. In between announcements, the caller hears
Music-On-Hold.
After the system plays all the announcements that you configured for the
ACD group, the system plays the last announcement repeatedly (for the
Using ACD
149
specified time interval) during the rest of the wait period: that is, until the
call is answered or until the ACD group’s timeout period is exceeded. If
the timeout period is exceeded, the system forwards the call to the
destination that you specified in the Group Coverage Action after
Timeout: field when you added or modified the ACD group.
If the agent answers the call, the system immediately stops playing the
announcement, or the Music-On-Hold, and connects the caller to the
appropriate agent.
Fields in the Announcements Window
Table 31 describes the function of each field and button in the
Announcements window (Click Call Distribution Groups > ACD
Announcements).
Table 31 Announcements Window: Field Descriptions
Field
Description
(List of WAV Files)
Displays a list of .WAV files currently known to ACD.
Record
Records a .WAV file for an ACD announcement. You must
have .WAV recording capability on the workstation you are
currently using.
Play
Plays back the .WAV file that you selected from the list of
WAV files.
Remove
Deletes the .WAV file that you selected from the list of
.WAV files.
Play/Record Extension
Lets you identify the telephone extension to which the
selected .WAV file applies.
Apply
Associates the .WAV file that you identified in the
Play/Record Extension.
Enter the New
Announcement Name
to Record
Lets you associate a mnemonic name with the .WAV file.
Enter Path for .WAV
File to Import
Announcement
Lets you point ACD to the location in the file system of the
.WAV file that you want to associate with the selected
telephone extension.
Browse
Instructs the system to search the file system under your
direction for the .WAV file to associate with the selected
telephone extension.
Import
Imports a .WAV file from the file system into the ACD list of
usable announcements.
150
CHAPTER 7: CALL DISTRIBUTION GROUPS
ACD Agents
The Agent List window allows you to display the status of each ACD
agent.
The statistical data does not contain the details for the ACD agents; the
display shows the overall summary of the ACD activity at that instance.
Fields in the Agent List Window
Table 32 describes the function of each field and button in the Agent List
window (Click Call Distribution Groups > ACD Agents).
Table 32 Agent List Window: Field Descriptions
Field
Description
Extension
Displays the telephone extension of the agent.
First Name
Displays the first name of the agent.
Last Name
Displays the last name of the agent.
Status
Identifies the current telephone status of the agent.
Categories include:
Connected - The agent's telephone is offhook.
Idle - The agent's telephone is onhook.
Ringing - The agent's telephone is ringing.
DNIS
Indicates whether the system is using Dialed Number
Identification Service (DNIS) to identify the caller to this
agent.
ANI
Indicates whether the system is using Automatic Number
Identification (ANI) to identify callers to this agent.
Call
Indicates whether the call that the agent is engaged in is an
ACD call or a non-ACD call.
Agent Edit List Window
You can add an agent to or remove an agent from the list of valid ACD
agents.
To assign a system user as an ACD agent, do the following:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Call Distribution Groups > ACD Agents.
3 Click the Edit List tab.
4 Click Show All to display a list of available telephone users.
Using ACD
151
5 Click the select box for the telephone user, or users, that you want to add
to the Agent List.
6 Click Apply.
If the number of agents exceeds the number allowed by the license (five
in the case of the Basic ACD license), the system disables the Add button
and displays an error message to indicate that the maximum number of
agents has been reached.
To unassign a system user as an ACD agent, do the following:
1 In the Agent List/User List, click the Select box for the ACD agent to clear
it. The system unassigns the agent from ACD responsibilities. To select all
extensions, enable the Select check box.
2 Click Apply.
ACD Statistics
The ACD Statistics window allows you to gather meaningful data about
agents, calls, and callers to specific ACD groups.
As the administrator, you can either view the data for a selected ACD at a
time, or view the data for all of the ACDs at the same time. The data
viewed is a “snapshot” of the ACD at the discrete time at which you
invoked the Statistics display.
Refresh the display to ensure that the data is current.
Fields in the ACD Statistics Window
Table 33 describes the function of each field and button in the ACD
Statistics window. ACD Statistics also shows the Resource Contention
statistics. (Contention occurs when the system does not have a port
available to assign to an ACD group.)
Table 33 Statistics Window: Field Descriptions
Field
Description
Resource Report
Displays instances of contention.
Extension
Displays the telephone extension for this ACD.
Name of ACD
Displays the name of the ACD that is associated with this
extension.
Logged In Agents
Displays the total number of agents logged in at the time
you invoked the Statistics window.
152
CHAPTER 7: CALL DISTRIBUTION GROUPS
Table 33 Statistics Window: Field Descriptions
Field
Description
Current Queue
Displays the number of calls that are currently in the call
waiting queue of this ACD.
Answered Calls
Calls to this ACD that were answered since the last reset of
the statistics facility.
Dropped Calls
Calls to this ACD that were dropped since the last reset of
the statistics facility.
Total Calls
Total number of calls to this ACD group that have been
received since the last reset of the statistics facility.
Last Reset Command
Date
The date/time stamp at which the statistics facility was last
reset (call counters reset to zero) for this particular ACD
group.
Reset ACD Statistics
Resets the statistics facility to zero.
Reset ACD and
Member Statistics
Resets the ACD and Member statistics, and updates the
Last Reset Command Date field.
If the ACD has not reset since last system reboot, the system displays a
null reset date value.
Contention
The system groups audio devices, such as voice mail ports, into a pool or
extension list in the dial plan. It uses this extension list or pool for delayed
announcements. The system selects an idle device from this list to play a
delayed announcement. The number of devices in this pool is based on
usage, and you can add or remove devices to suit the call volume.
On a system with NBX Voice Messaging, you can reserve NBX Voice Mail
ports for Delayed Announcements to prevent Auto Attendant or voice
mail applications from using the ports.
1 Create a new extension list and add the ports that you want to reserve
(click Dial Plan > Extension List, and then click Add).
2 Delete those ports, which you added to the new extension list, from the
default voice mail extension list (click Dial Plan > Extension List, and then
click *0003).
3 Edit the dial plan to include the new extension list (click Dial Plan >
Configure, and then click the Modify tab).
4 Configure the appropriate ACD group to use the new extension list for
Delayed Announcements:
Using ACD
153
a Click Call Distribution Groups > ACD Groups.
b Click the ACD group’s extension.
c Click the Announcements tab.
d From the Select a port to play announcements drop-down list, select
the new extension list.
The ports in the new extension list are now reserved and available
exclusively for Delayed Announcements.
On a busy system, there can be an additional delay in the playing of an
announcement. This condition can occur if all the audio resources (system
voice mail ports) from the Delayed Announcement Audio Pool are in use.
If this delay occurs, the scheduled announcement must queue up for an
audio resource to become available before it can be played to the caller.
During that time, the caller either hears ring-back (when the system
initially routes the call to the ACD Group for the initial announcement or
greeting) or Music-On-Hold (if the caller has already heard a
announcement, or the call is the result of a transfer or forward
operation).
To avoid this problem, you can:
■
Record or import announcements of short duration.
■
Add more audio resources (system voice mail ports) to the
Announcement Resource Pool.
154
CHAPTER 7: CALL DISTRIBUTION GROUPS
The system records the instances of contention and displays them on the
Resource Report window (click Call Distribution Groups > ACD Statistics
and click the Resource Report tab).
Table 34 Resource Report: Field Description
Hunt Groups
Field
Description
Extension
Extension number associated with this contention event.
Name of ACD
Name of the ACD group that could not be assigned a port,
causing the contention event.
Number of
Occurrences
Number of times that the contention event occurred.
Most Recent
Occurrences
List of the most recent occurrences of a contention event
with this extension in this ACD group.
Extension List
List of agent extensions affected by the contention.
Refresh
Brings the Resource Report data up-to-date.
A hunt group is a set of telephone users that you can access when you
dial a single extension. A call routed to the hunt group extension can
reach any member of the group who is currently logged into the group. A
static hunt group is one in which all members are permanently logged in
(locked). A dynamic hunt group lets you log telephone users in to and out
of the hunt group, or you can allow telephone users to log into or out of
the group themselves, using the hunt group password you create.
You can associate one or more of the hunt group login/logout feature
codes with a particular group and then map that feature code to a
telephone access button to allow telephone users to easily login and
logout of the hunt group. The access button light remains lit while the
user is logged into the hunt group.
Hunt groups are specified by extension, in these ranges:
■
V3000, V3001, V3001R, and V5000 systems: 4000–4099 (You can
assign all 100 extensions.)
■
NBX 100 systems: 450–499 (You can assign a maximum of 48
extensions.)
Hunt Groups
155
To configure hunt groups:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Call Distribution Groups > Hunt Groups.
3 See the online Help for more information.
To enable Supervisory Monitoring for a Hunt Group, define a Supervisory
Monitoring Domain (click Feature Settings > Supervisory Monitoring) that
includes the Hunt Group.
Hunt Group Considerations
■
For a telephone to participate in a hunt group, the telephone user
must be logged into the hunt group. See an NBX telephone guide for
more information.
■
You can lock in a member of a hunt group, which prevents the
member from logging out of the system. See the online Help for more
information.
■
When you create a hunt group, you specify one of three types: linear
hunt group, circular hunt group, or calling group. You base your
choice on the ringing pattern that you want.
■
For each group that you define, you also specify:
■
■
■
Linear and Circular
Hunt Groups
The Total Timeout — The length of time in seconds that the call
rings on the group’s telephones before the call goes to the group’s
call coverage point.
The Per-Device Timeout — The length of time in seconds that
each telephone rings in the cycle. (Ignored for Calling Groups.)
Whether you want the system to log a telephone out of the hunt
group if it does not answer. (Ignored for Calling Groups.)
■
For linear and circular hunt groups, the order in which a group
telephone rings (the telephone’s priority) is the same as the order in
which you added it to the group. For calling groups, all phones ring
simultaneously.
■
The Call Pickup feature is not supported for hunt groups.
In linear and circular hunt groups, calls ring sequentially on telephones in
the group, but the behavior differs when the time specified in the Total
Timeout field elapses:
156
CHAPTER 7: CALL DISTRIBUTION GROUPS
■
If the Total Timeout value is less than the sum of all of the Per-Device
Timeout values, a call that is routed to either a linear and circular hunt
group rings on some, but not all of the telephones in the group and
then is routed to the group’s call coverage point.
■
If the Total Timeout value is greater than the sum of the Per-Device
Timeouts:
■
■
For a Linear Hunt Group, the call rings in order on each group
telephone and then goes to the group’s call coverage point. The
system ignores any time remaining in the Total Timeout, and the
call does not ring again on any telephone in the group.
For a Circular Hunt Group, the call rings in order on each group
telephone and then, for the remainder of the Total Timeout, begins
ringing again through the telephones, in order. Depending on the
Total Timeout value, an unanswered call may ring through all
telephones in the group multiple times.
If the Total Timeout value exactly matches the sum of the Per-Device
Timeouts, the behavior of a single incoming call is the same for both
linear and circular hunt groups.
When the system routes a second call to a linear or circular hunt group,
the telephone on which the second call first rings is different:
Calling Groups
■
For a Linear Hunt Group, the new call rings on the first telephone in
the group.
■
For a Circular Hunt Group, the new call rings on the telephone that is
next in the ringing sequence.
In this special type of hunt group, an incoming call rings on all telephones
in the group simultaneously. After the Total Timeout value is reached, a
call that is still unanswered is routed to the group’s call coverage point.
The value in the Per Device Timeout field has no effect on the behavior of
telephones in a calling group.
Call Coverage
For each hunt group, you can define where the system routes an
unanswered call (the call coverage point):
■
Voice Mail — The system routes an unanswered call to the hunt
group extension’s voice mailbox or to a configured operator.
Hunt Groups
Hunt Group
Supervisory
Monitoring
157
■
Auto Attendant — The system routes an unanswered call to the
Automated Attendant that you specify.
■
Phone Number — The system routes an unanswered call to the
extension that you specify, such as the receptionist, or another hunt
group.
You can configure the system to allow a privileged user to join an
ongoing conversation in a hunt group with or without the knowledge of
the parties involved in that conversation. This feature is called Supervisory
Monitoring.
The monitoring user is called the supervisor. The supervisor, who may or
may not be the system administrator, can join a call between a person
calling into the system (for example, a customer) and a person on-site
whose job it is to accept incoming calls. Joining calls in progress can
ensure proper customer support.
To enable Supervisory Monitoring for a Hunt Group, you must define a
Supervisory Monitoring Domain (Feature Settings > Supervisory
Monitoring) that includes the Hunt Group. For more information about
Supervisory Monitoring, see “Supervisory Monitoring” in Chapter 3.
158
CHAPTER 7: CALL DISTRIBUTION GROUPS
8
PSTN GATEWAY CONFIGURATION
This chapter describes how to configure PSTN gateway devices on the
system and addresses these topics:
■
Configuring and Managing Analog Line Card Ports
■
Configuring and Managing Digital Line Cards
■
Setting Up a Digital Line Card at a Remote Location
■
Setting Up T1/E1 Logging
■
Viewing CSU State Information and Statistics
■
Using Loopback Tests
■
Obtaining a Dial Tone from a PBX System
For more information about these topics and configuration procedures,
see the online Help.
For information about installing the system hardware components, see
the NBX Installation Guide.
Configuring and
Managing
Analog Line Card
Ports
Each Analog Line Card provides access for up to four local telephone lines
into your system. The Call Processor treats a line card port as an
extension, so each line card port needs its own extension number.
You use Auto Discovery to detect line card ports, and you define the
starting address for Auto Discovery of devices in the system dial plan. For
a 3-digit dial plan, the default starting address is 750; for a 4-digit dial
plan, the default starting address is 7250. Auto Discovery assigns the first
unassigned number, starting at 750 (or 7250 for a 4-digit dial plan), to
the first line card port.
You typically configure line cards during installation. See the NBX
Installation Guide for more information.
160
CHAPTER 8: PSTN GATEWAY CONFIGURATION
If you remove a line card from the system, the port information remains in
the system database. The extension numbers assigned to the four ports
do not become available for reuse unless you use the NBX NetSet utility
to remove the line card from the configuration database.
This section describes these topics:
Configuring a
Line Card Port
■
Configuring a Line Card Port
■
Modifying a Line Card Port
■
Removing a Line Card Port
■
Verifying Line Card Port Status
■
Rebooting a Line Card Port
■
Advanced Settings
When you configure a line card port, you can assign it as a member of a
line pool.
You can configure a line card port automatically (recommended) or
manually.
Verify that you have chosen a 3-digit or 4-digit dial plan before you begin
to configure line card ports. See Chapter 11 for information about how
to configure the dial plan.
Configuring a Line Card Port Automatically
To configure a line card port automatically:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
1 Click System-Wide Settings > Auto Discovery.
2 Enable the Auto Discover Other Devices (including ATA, Digital Line Cards
& Analog Line Cards) check box.
3 Click Apply.
Configuring a Line Card Port Manually
Most organizations use Auto Discovery to configure line card ports
automatically. However, you can configure a line card port manually and
select all settings.
Configuring and Managing Analog Line Card Ports
161
To configure a line card port manually:
1 Click PSTN Gateway Configuration > Analog Line Cards.
2 Click Add.
3 Specify the port information. See the online Help for more information.
4 Click OK.
5 Connect your CO line to the configured port.
Auto Extension Behavior
The extensions you specify in the Auto Extension fields control where the
system directs a call. Table 35 describes typical the behaviors for Auto
Extension.
Table 35 Auto Extension Configuration
Button Mapping Setting
for This Line
Auto Extension
Setting
Incoming Call Behavior
Not mapped to any
telephone
Extension of the
Receptionist
Receptionist’s telephone rings. If no one answers, the call transfers
to the call coverage point defined for the Receptionist’s telephone.
The transfer occurs after the number of rings specified for the
Receptionist’s telephone.
Not mapped to any
telephone
500
Mapped to a button on the Extension of the
Receptionist’s Telephone (or Receptionist
to a button on an Attendant
Console associated with the
Receptionist’s telephone)
Calls go directly to the Automated Attendant without ringing any
telephone.
Receptionist’s telephone rings. If no one answers, the call transfers
to the call coverage point defined for the Receptionist’s telephone.
The transfer occurs after these two values are surpassed:
■
The number of seconds specified in the Time Out field for the
appropriate time of day (Open, Closed, Lunch, Other). Click
PSTN Gateway Configuration > Analog Line Cards and click an
extension.
■
The number of rings specified in the user settings for the
Receptionist’s telephone.
Example: If the Time Out value for the Analog Line Card port is 12
seconds, the equivalent number of rings is 2. If the Call Forward
settings for the receptionist’s telephone is 4 rings, then the call
transfers after 6 rings.
162
CHAPTER 8: PSTN GATEWAY CONFIGURATION
Table 35 Auto Extension Configuration (continued)
Button Mapping Setting
for This Line
Auto Extension
Incoming Call Behavior
Setting
Mapped to a button on the 500
Receptionist’s Telephone (or
to a button on an Attendant
Console associated with the
Receptionist’s telephone)
Receptionist’s telephone rings. If no one answers, the call transfers
to the Automated Attendant.
NOTE: The call coverage point defined for the receptionist’s
telephone has no affect.
The transfer occurs after the number of seconds specified in the
Time Out field for the appropriate time of day (Open, Closed,
Lunch, Other). Click PSTN Gateway Configuration > Analog Line
Cards and click an extension.
Mapped to a button on a
Extension of the
user telephone (or to a
Receptionist
button on an Attendant
Console associated with the
user’s telephone)
User telephone rings. If no one answers, the call transfers to the
Receptionist’s telephone.
The transfer occurs after the number of seconds specified in the
Time Out field for the appropriate time of day (Open, Closed,
Lunch, Other). Click PSTN Gateway Configuration > Analog Line
Cards and click an extension.
If the receptionist’s telephone is not answered, the call transfers to
the call coverage point defined for the receptionist’s telephone.
Mapped to a button on a
500
user telephone (or to a
button on an Attendant
Console associated with the
user’s telephone)
Modifying a
Line Card Port
User telephone rings. If no one answers, the call transfers to the
Automated Attendant.
The transfer occurs after the number of seconds specified in the
Time Out field for the appropriate time of day (Open, Closed,
Lunch, Other). Click PSTN Gateway Configuration > Analog Line
Cards and click an extension.
You can modify a line card port that is already configured.
To modify a line card port:
1 Click PSTN Gateway Configuration > Analog Line Cards.
2 Click the extension of line card port that you want to modify.
3 Specify the port information. See the online Help for more information.
4 Click OK.
Removing a
Line Card Port
When you remove a line card port that is already configured, you remove
the port information from the system database.
Configuring and Managing Analog Line Card Ports
163
To remove a line card port:
1 Click PSTN Gateway Configuration > Analog Line Cards.
2 Select the extension, or extensions, of the line card port that you want to
delete and click Remove Selected. To select all extensions, enable the
Select check box.
3 Click OK when the system prompts you to confirm.
Verifying Line Card
Port Status
You can verify the status of a configured line card port at any time.
To view the status of a line card port:
1 Click PSTN Gateway Configuration > Analog Line Cards.
2 Click the extension of the line card port.
3 Click the Status tab.
4 See the online Help for more information.
Rebooting a
Line Card Port
To reboot a line card port:
1 Click PSTN Gateway Configuration > Analog Line Cards.
2 Click the extension of the line card port.
3 Click the Status tab.
4 Click Reset Device.
CAUTION: On the 3C10117 Analog Line Card, you can reboot individual
ports without affecting the other ports. However, if you reboot an analog
port on the 3C10114C or 3C10114D Analog Line Card, the system
reboots all ports on the card. This action can disrupt active telephone calls
on any of these ports.
Advanced Settings
The Advanced Settings window enables you to set the audio gain and
timing controls on each port of an Analog Line Card.
To set these parameters:
1 Click PSTN Gateway Configuration > Analog Line Cards.
2 Click the extension of the line card port.
3 Click the Advanced Settings tab.
164
CHAPTER 8: PSTN GATEWAY CONFIGURATION
4 See the online Help for more information about the dialog box fields.
If you change any of the values in the Advanced Settings window, the
settings that you change persist if you upgrade the system software or
change the regional software later.
Configuring and
Managing Digital
Line Cards
This section describes how to add and configure these Digital Line Cards:
■
T1 Digital Line Card to connect to a T1 service that the local telephone
company provides.
You can configure the T1 Digital Line Card to use one of two types of
signaling:
■
DS1 protocol (sometimes referred to as Standard T1)
■
ISDN PRI (Primary Rate Interface) signaling
The system provides E911 (emergency) connectivity if the T1 Digital
Line Card is configured for ISDN PRI signaling. The system provides
the calling number (ANI) so that the emergency services personnel
can find the location of the caller from the E911 database. You
must update the CO (PSAP) databases.
■
E1 Digital Line Card to connect to an E1 service that the local
telephone company provides.
You can configure an E1 Digital Line Card for ISDN PRI signaling only.
■
BRI-ST Digital Line Card to manage a BRI line with four BRI spans
using the ST interface.
Each BRI-ST Digital Line Card (3C10164C or 3C10164D) supports the
Basic Rate Interface protocol (ST interface only).
The Port, Channel, and BRI Group configuration instructions in this
chapter apply to the 3C10164D Digital Line Card and to the BRI-ST ports
on the V3000 BRI-ST, 3C10601A.
The 3C10164D is a gateway device capable of providing BRI-ST digital
interfaces. The 3C10164D card supports eight BRI channels (four ports).
This section describes these topics:
■
Adding a Digital Line Card
■
Configuring and Managing Digital Line Cards
■
Digital Line Card Status Lights
Configuring and Managing Digital Line Cards
■
Modifying a Digital Line Card
■
Support of AT&T’s 4ESS Switch Protocol
■
Adding or Modifying a Digital Line Card Group
■
Modifying Card Channels
■
Modifying IP Settings
■
Removing a Digital Line Card
165
3C10165D E1 and 3C10116D T1 Digital Line Cards have expanded
capabilities that are described in these topics:
Adding a Digital Line
Card
■
Setting Up a Digital Line Card at a Remote Location
■
Setting Up T1/E1 Logging
■
Viewing CSU State Information and Statistics
■
Using Loopback Tests
To add a Digital Line Card to a system, use the information in these
sections:
■
Preparing the System for Digital Line Cards
■
Ordering DID, CLIP, and MSN Services
■
Enabling Auto Discovery for Digital Line Cards
■
Inserting the Digital Line Card
Preparing the System for Digital Line Cards
Before you insert a:
■
T1 Digital Line Card into the chassis, order a T1 line from your
telephone carrier
■
E1 Digital Line Card into the chassis, order an E1 line, with the
specifications you want, from your telephone carrier
■
BRI-ST Digital Line Card into the chassis, order an ISDN BRI-ST line
from your telephone carrier
Have the telephone carrier install the line.
In some cases, the telephone company offers T1 services only with
specific, pre-defined parameters. However, some telephone companies
offer a number of configuration choices with their T1 services.
166
CHAPTER 8: PSTN GATEWAY CONFIGURATION
Ordering DID, CLIP, and MSN Services
When you order a:
■
BRI line with DID (Direct Inward Dial) capability, Calling Line ID
Presentation (CLIP), or MSN services
■
E1 line with DID (Direct Inward Dial) capability, Calling Line ID
Presentation (CLIP), or MSN services
■
T1 line with DID (Direct Inward Dial) capability
the local telephone carrier assigns a block of telephone numbers to you.
Usually, you can request a specific range of numbers, but sometimes the
carrier assigns numbers other than the ones you request.
You may be able to request that the local telephone carrier pass you a
specific number of digits for each incoming telephone call. Sometimes
the carrier does not offer any choice. In either situation, you need to
know how many digits the carrier passes.
Example: Carriers commonly pass either the last three digits or last four
digits of the number for each incoming call.
Sometimes the last digits of the telephone numbers that the carrier
assigns to you do not match the telephone extension numbers you want
to use for internal calls. Create entries in your dial plan configuration file
to trans- late the incoming numbers into the corresponding extension
numbers.
Example: You want to use internal extensions from 4000 through 4999,
but the local telephone carrier assigns you numbers from 617-555-3500
through 617-555-4499. You can create translator entries in the dial plan
configuration file to translate an incoming digit sequence such as 3795
into extension number 4295, and a sequence such as 4213 into 4713.
The configuration requires several translator entries to manage subsets of
the total range. A unique set of entries would manage incoming digit
sequences from 3500 through 3599, from 3600 through 3699, and each
of the other sequences in which the first two digits were unique in the
range from 37XX through 44XX.
If the DDI/DID (Direct Inward Dial/Direct Dial Inward) numbers match your
internal extension numbers, the translator entries in your dial plan
configuration file can be much simpler.
Configuring and Managing Digital Line Cards
167
Example: You plan to use internal extensions from 100 through 299,
and the local telephone company assigns you numbers from
617-555-4100 through 617-555-4299. If the local telephone carrier
passes you three digits, you need no translator entries in the dial plan
configuration file. If the carrier passes you four digits, you could add a
single set of translator entries to the configuration file to remove the first
digit (4) and use the remaining three digits as the internal extension.
Enabling Auto Discovery for Digital Line Cards
To enable Auto Discovery for Digital Line Cards:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
1 Click System-Wide Settings > Auto Discovery.
2 Enable Auto-Discover Other Devices (including ATA, Digital Line Cards &
Analog Line Cards) check box.
3 Click Apply.
Other check boxes may be enabled based on previous Auto Discoveries.
You do not need to clear these check boxes to install the Digital Line
Card. However, it is good practice to clear all check boxes other than the
one that you want to enable so that the Call Processor does not continue
to search for added devices.
Inserting the Digital Line Card
You do not need to remove the power cable from the chassis before you
insert the Digital Line Card.
To insert the Digital Line Card into the chassis:
1 Record the MAC address of the Digital Line Card.
2 Select a slot for the Digital Line Card in the chassis.
3 Insert the Digital Line Card into the slot.
Slide the Digital Line Card into the chassis until you feel it touch the
connectors.
4 To seat the Digital Line Card into the connectors, apply firm pressure to
both the left and right sides of the front of the card.
5 Tighten the left and right screws on the front of the Digital Line Card to
secure it to the chassis.
6 Wait 3 minutes.
168
CHAPTER 8: PSTN GATEWAY CONFIGURATION
CAUTION: When you insert a Digital Line Card, it begins an initialization
sequence that may include a firmware upgrade. Also, because you
enabled the Auto Discovery feature, the system recognizes the new card
and begins to update its database. Allow 3 minutes for these processes to
complete.
CAUTION: The T1 Digital Line Card reboots twice during the initialization
process. If you attach a console cable to the COM1 port on the T1 card
and use Hyperterm software to view the text output from the card, you
see status messages associated with the two reboot processes. See
“Connecting a Computer to a Serial Port” on page 447.
Another way that you can be sure that it is safe to proceed is to examine
the status lights on the front panel of the T1 card. After the Auto
Discovery process completes, and before you connect the T1 Digital Line
Card to the telephone company’s T1 line, the CF (Carrier Fail) light
appears solid green on a 3C10116C card. On a 3C10116D card, the
POST, DNLD, CARD and Call Processor lights appear solid green. For more
information about T1 card status lights, see “E1 and T1 Digital Line Card
Status Lights” on page 173.
You are now ready to configure the Digital Line Card.
Configuring the
Digital Line Card
These sections tell you how to use the NBX NetSet utility to set up your
Digital Line Card ports:
■
Configuring the Digital Line Card
■
Connecting the Line and Activate the Span
■
Configuring Digital Line Card Groups
■
Verifying Group Membership
■
Completing the Configuration
Before you configure the Digital Line Card, see Chapter 11 for more
information about how to configure the dial plan.
Configuring the Digital Line Card
CAUTION: Before you begin to configure the Digital Line Card, wait
3 minutes after you insert the Digital Line Card into the chassis.
Configuring and Managing Digital Line Cards
169
To configure the Digital Line Card:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Auto Discovery.
3 Enable the Auto Discover Other Devices (including ATA, Digital Line Cards
& Analog Line Cards) check box, if necessary.
4 Click PSTN Gateway Configuration > Digital Line Cards.
The T1/ISDN Board List displays all Digital Line Cards (T1, E1, or BRI-ST)
that the system discovers. the NBX NetSet utility refers to Digital Line
Cards as either cards or boards.
By default, the Auto Discovery process selects DS1 as the signaling type
for a T1 Digital Line Card.
5 In the T1/ISDN Board List, click the MAC address of the Digital Line Card
that you installed into the chassis.
6 To change the name of the Digital Line Card, edit the contents of the
Board Name field to identify the card in device lists.
7 For BRI service, verify that the Card Type field displays ISDN BRI. If it does
not, the system has not properly autodiscovered the card. Restart the
installation process.
8 To change the signaling type for a T1 Digital Line Card to ISDN PRI, select
ISDN PRI from the Card Type drop-down list.
To see the change, you may need to wait a minute or two, and refresh
your browser window.
9 Enable the On Line check box.
10 Verify that the system lists all channels.
The Channel List displays all channels. The channel numbers appear after
the MAC address, separated by a hyphen.
Example:
2...00:01:03:48:e0:4e-2.... New Trunk.
The 2 after the hyphen indicates channel number 2.
Verify that system lists:
■
All 30 channels for an E1 board.
■
All 24 channels for a T1 board.
170
CHAPTER 8: PSTN GATEWAY CONFIGURATION
■
The highest channel as 23 for a T1 ISDN PRI board.
When you configure a T1 Digital Line Card for ISDN PRI signaling, one
of the 24 channels is allocated for signaling, leaving 23 for data
(voice).
11 Click Apply.
Connecting the Line and Activate the Span
1 Plug the line into the Digital Line Card.
For BRI service, use a category 5 Ethernet cable to connect the BRI
interface box to one of the ports on the front panel of the BRI-ST card or
the V3000 BRI-ST.
2 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
■
PSTN Gateway Configuration > ISDN BRI Spans
3 Click the MAC address of a span.
4 Enable the On Line check box.
5 Click OK.
6 In the T1/ISDN Board List, verify that the entry for this card in the Status
column changes from Offline to Ready. You may need to wait a minute or
two, and then refresh your browser window to see this change.
For reports about all installed Digital Line Cards, click PSTN Gateway
Configuration > Digital Line Cards, and then click Config. & Status Report
and Export Report. See “Digital Line Card Troubleshooting” on page 415
for more information.
Configuring Digital Line Card Groups
To configure the Digital Line Card groups:
1 Click the appropriate link:
■
PSTN Gateway Configuration > IT1 Groups
■
PSTN Gateway Configuration > ISDN PRI Groups
■
PSTN Gateway Configuration > ISDN BRI Groups
2 Click the name of a group.
Configuring and Managing Digital Line Cards
171
For T1 Digital Line Card groups, the fields in the Modify window contain
default values. No default values are assumed for Called Party Digits or
Calling Party Digits.
3 To modify the name of the group, enter a new name in the Group Name
field. You can use alphanumeric characters, hyphens, and underscores.
The maximum name length is 30 characters.
4 To prohibit call transfers between trunk lines, select Restricted (the
default value) from the Trunk to Trunk drop-down list. Otherwise, select
Unrestricted.
CAUTION: If you select Unrestricted, telephone users can transfer
incoming calls to outgoing trunks. 3Com does not recommend this
setting because it enables the possibility of toll fraud.
5 For T1 Digital Line Cards, modify the Wink Wait value:
a Select Wink Wait from the Timer Values list.
b Type 3000 in the New Value field.
c Click Apply.
d Ask your telephone service provider to set their Wink Wait value to
3000 msec.
6 For T1 Digital Line Cards, modify the Guard value:
a Select Guard from the Timer Values list.
b Type 2200 in the New Value field.
c Click Apply.
d Ask your telephone service provider to set their Guard value to
2200 msec.
7 Enable the On Line check box.
8 Verify that 500 (the default) is in each of the four AutoExt fields.
9 Click OK.
Verifying Group Membership
To verify that all channels are in the member list:
1 Click the appropriate link:
■
PSTN Gateway Configuration > IT1 Groups
■
PSTN Gateway Configuration > ISDN PRI Groups
172
CHAPTER 8: PSTN GATEWAY CONFIGURATION
■
PSTN Gateway Configuration > ISDN BRI Groups
2 Click the name of a group.
3 Click the Membership tab.
4 Verify that all channels are present.
Completing the Configuration
To complete the Digital Line Card installation:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Channels
■
PSTN Gateway Configuration > ISDN PRI Channels
■
PSTN Gateway Configuration > ISDN BRI Channels
2 Wait approximately 30 seconds for the status of each channel to change
from Ready to Idle.
3 Verify the status of each channel.
If the channel status does not display as Idle, verify that you have enabled
the On Line check box for the card, the span, and the group.
While you are waiting, you can click Apply to refresh the list of channels
and to see the updated status. If you have connected the telephone
company’s line to the Digital Line Card, the Nominal (on 3C10165C E1
and 3C10116C T1 Digital Line Cards) or the CO (on 3C10165D E1 and
3C10116D T1 Digital Line Cards) status light on the front panel of the
Digital Line Card illuminates (solid green). If the light does not illuminate
and you have an E1 or T1 line connected, disconnect the line and connect
a loopback connector. If the light now illuminates, contact the telephone
company for assistance with the line. If the light does not illuminate,
contact your 3Com Technical Support representative.
Digital Line Card
Status Lights
This section describes:
■
BRI-ST Card Status Lights
■
E1 and T1 Digital Line Card Status Lights
BRI-ST Card Status Lights
Each of the four spans on a BRI-ST card has status lights that indicate the
status of the span (Table 36).
Configuring and Managing Digital Line Cards
173
Table 36 BRI-ST Card Status Lights
Status
D
B1
B2
Off
No Layer 1 connection is
established with the Central
Office (CO).
The channel is not
carrying a call.
The channel is not
carrying a call.
Yellow
A Layer 1 connection is
established but the channel
is not yet ready to make or
receive calls.
A call build-up is
occurring.
A call build-up is
occurring.
Green
The channel is ready to make A call is connected. A call is connected.
and receive calls.
E1 and T1 Digital Line Card Status Lights
The 3C10165, 3C10165B, and 3C10165C E1 cards and the 3C10116C
T1 card display these status lights:
■
CF — Carrier Fail (when lit, indicates either a red alarm or blue alarm)
■
RA — Remote Alarm (yellow alarm)
■
LB — Loopback (when lit, indicates that the card is in loop-back
testing mode; does not indicate any of the red, blue, or yellow alarms)
■
Nominal — The card is framed
The 3C10165D E1 and the 3C10116D T1 cards display these status lights:
■
CO — Central Office:
Amber — Alarm condition at the remote end or the CO is not
connected or available.
Green — No alarm condition; the card has a valid connection to the
Central Office.
■
POST — Power On Self Test:
Off — POST test is running. The test runs approximately 5-seconds
after you apply power to the board. After 5-seconds, Off indicates the
POST test failed.
Green — POST test completed successfully.
■
DCH — D channel status of an ISDN PRI connection:
Off — No line is attached or the card does not need a D channel, such
as when the card is running T1-robbed-bit (CAS).
Green — Card is configured for ISDN PRI operation and an active PRI
connection has been established.
174
CHAPTER 8: PSTN GATEWAY CONFIGURATION
Amber — The D channel has not yet been established. It can take
several seconds after the card has completed its power up tests for the
card to establish a connection with the PRI trunk. If the DCH light
changes to amber after the connection has been established, an active
control channel connection through the PRI line may have been lost.
■
DNLD — Download:
Flash — The card is downloading software from the Call Processor.
Green — The download has been completed.
Amber — The download was interrupted before it completed.
On a LAN, the download process completes quickly. If the download
from Call Processor to Digital Line Card must travel a routed network
path, the download may take a few minutes. If the DNLD light
remains amber, it may indicate a severely congested network or a
hardware problem with the card.
■
CALL — Call audio traffic:
Off — No audio traffic on the link.
Flashing — Audio traffic is present.
■
CARD — Card Software Status:
Green — The card has finished downloading software from the Call
Processor and all software processes have started successfully.
Amber — A problem with one or more of the software processes
running on the card. The card automatically reboots itself if it detects
a problem with any of its software processes.
■
DSP — Reserved for future use.
■
NCP — Call Processor communications status:
Amber — The card is trying to establish contact with a Call Processor.
Green — The card has established contact with a Call Processor.
■
LNK — Ethernet link status:
Green — The 10/100 Uplink port is connected to a 10Mb or to a
10/100 Mb hub or switch.
Red — The 10/100 Uplink port is connected to a 100 Mb hub or
switch.
Off — There is no connection to the 10/100 Uplink port.
■
ACT— Ethernet activity
Configuring and Managing Digital Line Cards
175
Rapid blink — Data is passing into or out of the card through the
10/100 Uplink port.
Modifying a Digital
Line Card
These sections tell you how to modify a Digital Line Card that is already
installed in the system:
■
Modifying a Span
■
Configuring Partial E1 and T1 Lines
■
Modifying Span Audio Controls
Modifying a Span
To modify a span:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
■
PSTN Gateway Configuration > ISDN BRI Spans
2 Click the MAC address of a span you want to modify.
3 Make the necessary changes. See the online Help for more information
about the fields.
Depending on the configuration of the Digital Line Card:
■
The ISDN BRI-ST Digital Line Card supports two or four channels for
each span.
■
The E1 Digital Line Card supports 30 channels for each span.
■
The T1 Digital Line Card configured for DS1 supports 24 channels. The
T1 Digital Line Card configured for ISDN PRI, it supports 23 channels.
4 Enable the On Line check box to bring the span online.
Note that the span does not come online unless the card is online first.
5 Click OK.
Configuring Partial E1 and T1 Lines
Some telephone companies offer an E1 or T1 line that has less than the
maximum number of channels implemented. This is called a Fractional,
Partial, or Subequipped E1 and Subequipped T1.
Example: To reduce near-term costs, you may decide to purchase 15
channels now and implement more later.
176
CHAPTER 8: PSTN GATEWAY CONFIGURATION
Some telephone companies offer Partial E1and T1 lines as their standard
offering, and provide fully implemented E1 and T1 lines only if you make
a specific request. If you are unaware of this policy, outbound calls using
the E1 or T1 line may fail because, by default, the system places
outbound calls using high numbered channels first, and a Fractional E1 or
T1 typically has the lower numbered channels implemented.
If you see the REQ_CHANNEL_UNAVAIL error message in the span Status
window under the Details of last five calls heading, follow these steps to
find out if a Partial E1 or T1 is causing the error:
1 Remove the highest numbered channel from service (set it offline) and
retry the outbound call. See Modifying Card Channels on page 182 for
information about how to modify a channel
2 Continue to remove channels until an outbound call succeeds.
3 When the first outbound call succeeds, the highest numbered channel
still in service represents the number of active (provisioned) channels in
the Partial E1 or T1.
4 Create two groups. Put all of the active channels in one group, and all of
the inactive channels in the other. Mark the active group online and the
inactive group offline. See Adding or Modifying a Digital Line Card Group
on page 179 for more information about creating groups.
Modifying Span Audio Controls
Normally, you do not need to change the Audio Controls from their
default settings. If you have a problem with sound quality that you
cannot resolve by using the volume controls on the 3Com telephones,
contact your 3Com Technical Support representative.
CAUTION: Do not change your Audio Controls settings unless a qualified
technical support representative instructs you to do so.
Audio Controls settings affect individual spans. You can edit these
properties:
■
Silence Suppression (3C10165D cards only) — Enables you to override
the system-wide setting. For a detailed description of how silence
suppression affects audio quality and bandwidth, see “Audio
Settings” on page 34.
■
Audio Compression (3C10165D cards only) — Enables you to override
the system-wide setting. For a detailed description of how audio
Configuring and Managing Digital Line Cards
177
compression affects audio quality and bandwidth, see “Audio
Settings” on page 34.
■
Audio Source Gain — Enables you to adjust the audio gain to resolve
volume issues.
CAUTION: Do not change your Audio Source Gain settings unless you
are instructed to do so by a technical support representative.
To modify span audio controls:
1 Click the appropriate link:
■
PSTN Gateway Configuration > IT1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
■
PSTN Gateway Configuration > ISDN BRI Spans
2 Click the MAC address of the span you want to modify.
The number of channels supported for each span depends on the
configuration of the Digital Line Card. E1 cards support 30 channels for
each span.
3 Click the Audio Controls tab and see the online Help for more
information.
4 Enable the Echo Canceller Enabled check box if you want to turn on echo
cancellation.
There are two situations in which it may be desirable to disable echo
cancellation on a T1 Digital Line Card:
■
If a system is connected to a telephone carrier (Central Office) by a T1
Digital Line Card, and the telephone carrier guarantees to provide
echo cancellation on all channels at all times.
■
If T1 Digital Line Cards directly connect two systems, and the network
between the two is completely composed of digital circuitry, thus
eliminating sources of echo.
You can enable or disable echo cancellation for each T1 Digital Line Card.
However, you cannot enable or disable echo cancellation on individual
channels.
CAUTION: Before you enable echo cancellation for a T1 Digital Line Card,
verify that the card is configured for DS1 operation and not ISDN PRI
operation.
5 Click OK.
178
CHAPTER 8: PSTN GATEWAY CONFIGURATION
Support of AT&T’s
4ESS Switch Protocol
4ESS is the AT&T proprietary version of ISDN. You can select the 4ESS
protocol when you configure a T1 Digital Line Card for PRI (Primary Rate
Interface) operation. If you select the 4ESS protocol, you can optionally
use Call By Call Service Configuration which enables you to select one of
three access services:
■
SDN (Software Defined Network) — A premises-to-premises service
with voice and voice-grade data transport, plus a number of
customer-controllable call management and call monitoring features
(for example, Virtual Private Networking). You cannot configure SDN
as the default setting but you can configure the system dial plan to
use SDN.
■
MEGACOM — A high-volume outward calling service. MEGACOM
can be the default setting.
■
Long Distance — The default service if you select the 4ESS protocol,
but purchases no other services. You can use Long Distance with SDN
but not with MEGACOM.
Selecting the 4ESS Protocol
To enable the 4ESS protocol:
1 Click PSTN Gateway Configuration > ISDN PRI Spans.
2 Click the MAC address of a span.
3 From the CO Switch Protocol drop-down list, select AT&T Custom - 4ESS.
4 Click either:
a OK to enable the 4ESS protocol and exit from the window.
b Apply to enable 4ESS, to remain in the Modify window and configure
Call-By-Call Service. See “Setting Up a Digital Line Card at a Remote
Location” on page 185 for more information.
Configuring Call-By-Call Service
You order the optional Call-By-Call Service from your long-distance carrier
only if you order the 4ESS protocol. 3Com does not support Call-By-Call
Service with any other protocol.
To configure Call-By-Call Service:
1 Click PSTN Gateway Configuration > ISDN PRI Spans.
2 Click the MAC address of a span.
3 Enable the Enable Call-By-Call Service check box.
Configuring and Managing Digital Line Cards
179
4 In the Carrier Identification Code field, type the identification code for
your long-distance carrier.
Your long-distance carrier can supply this code when you order PRI
services, or you can ask the carrier for their code number. Another way to
obtain the code is to access the web site for the North American Number
Plan Administration (http://www.nanpa.com). In the menu in the left
frame, click Numbering Resources > Carrier Identification Codes (CIC).
Click the appropriate links to view the Feature Group B CIC and Feature
Group D CIC assignments. Search the documents to find the
identification code for your long-distance carrier. For example, AT&T is
listed next to code 288 in the Group D document.
5 From the Default Outbound Service drop-down list, select either
MEGACOM or Standard (LDS) as the service to use as the default. You
can configure the system dial plan to use a particular service.
Select MEGACOM as the default service only if you purchased
MEGACOM from your long-distance carrier. You cannot select Standard
(LDS) as the default service if you purchased MEGACOM, because these
two services do not work together.
6 Click OK.
Adding or Modifying
a Digital Line Card
Group
A Digital Line Card group is one or more channels that are assigned the
same characteristics, such as Channel Protocol.
These sections tell you how to perform these tasks:
■
Adding a Digital Line Card Group
■
Modifying a Digital Line Card Group
■
Changing Digital Line Card Group Membership
■
Removing a Digital Line Card Group
Adding a Digital Line Card Group
You add a new group when you need to assign common characteristics
to several Digital Line Card channels.
To add a Digital Line Card group:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Groups
■
PSTN Gateway Configuration > ISDN PRI Groups
180
CHAPTER 8: PSTN GATEWAY CONFIGURATION
■
PSTN Gateway Configuration > ISDN BRI Groups
2 Click Add and see the online Help for more information.
Modifying a Digital Line Card Group
You may want to modify a Digital Line Card group to change its name,
Auto Extension assignments, or other parameters. When you modify a
group, the changes affect all of the Digital Line Cards that are assigned to
the group.
CAUTION: When you modify a Digital Line Card group, you disconnect
any active calls on any channels that are associated with the group.
To modify a Digital Line Card group:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Groups
■
PSTN Gateway Configuration > ISDN PRI Groups
■
PSTN Gateway Configuration > ISDN BRI Groups
2 Click the name of the group that you want to modify.
3 To modify the name of the group, enter a new name in the Group Name
field. You can use alphanumeric characters, hyphens, and underscores.
The maximum name length is 30 characters.
4 Make the necessary changes to the group parameters. See the online
Help for more information.
5 Enable the On Line check box to bring the group on line.
The group does not come online unless the card and the span are online
6 Click OK.
Changing Digital Line Card Group Membership
You may want to modify the channel membership in a group to
accommodate changing needs.
Each channel must belong to a group. A channel can belong to only one
group. You cannot move a channel from the members list to the
non-members list of a group unless the system can assign the channel to
another group. If a channel has never been a member of a group, the
system cannot find a group to which it can move the channel. Therefore,
it cannot remove the channel from the member list. If a channel has been
Configuring and Managing Digital Line Cards
181
a member of a group in the past, the system moves the channel to the
group of which the channel was most recently a member.
Example: By default, the system creates two groups, Group 1 and Group
2, and places all channels in Group 1. If you try to move a channel to the
non-member list of Group 1, the operation fails. If you:
1 Select Group 2.
2 Click the Membership tab.
3 Move a channel from the non-member list to the member list.
4 Move the same channel back to the non-member list
the operation succeeds because the channel was previously a member of
Group 1. If you then view the Group 1 membership list, it contains the
channel you just removed from Group 2.
To change group membership:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Groups
■
PSTN Gateway Configuration > ISDN PRI Groups
■
PSTN Gateway Configuration > ISDN BRI Groups
2 Click the name of the group that you want to modify.
3 Click the Membership tab.
4 Enable the Copy Group Settings to Channels check box so that the
system copies the settings of the group to each channel you add or
remove. Otherwise, the system does not change the channel settings.
5 Enable the Refresh Channels on Add/Remove field so that the system
updates the channel status when you add or remove channels.
6 To add a group member:
a If the group does not include any members, enable the check boxes
next the MAC addresses that you want to add to the group.
b If the I group already has members, click Show all to display a list of
MAC addresses that you can add to the group’s membership.
Note: You can toggle between the Show all and Show members only
buttons to display MAC addresses that have membership in the group
and the MAC addresses that are not members of the group but who you
can add to the group, and to confirm your changes.
182
CHAPTER 8: PSTN GATEWAY CONFIGURATION
To remove a channel from a group:
1 Clear the check boxes next the MAC address of the channel or channels
that you want to remove.
2 Click OK.
Removing a Digital Line Card Group
You may want to remove any group that you no longer need.
To remove a group:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Groups
■
PSTN Gateway Configuration > ISDN PRI Groups
■
PSTN Gateway Configuration > ISDN BRI Groups
2 Select the group, or groups, that you want to delete and click Remove
Selected. To select all groups, enable the Select check box.
3 Click OK when the system prompts you to confirm.
Modifying Card
Channels
The number of channels for each span varies according to the
configuration. Each channel can accommodate a single telephone call.
This section describes how to modify channels for an installed card and
how to view the status of an existing channel.
If you use Auto Discovery to add channels on an E1 PRI line, note that the
30 channels the system discovers are numbered 1 through 15, and 17
through 31. This reflects the physical channel mapping on the E1
interface, in which channel 16 is the ISDN D-channel, that is used for
signaling.
CAUTION: Do not modify channels unless a 3Com Technical Support
representative advises you to do so. When you modify an ISDN channel,
you disconnect any existing calls on that channel.
Modifying a Digital Line Card Channel
To modify a channel on an installed Digital Line Card:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Channels
Configuring and Managing Digital Line Cards
■
PSTN Gateway Configuration > ISDN PRI Channels
■
PSTN Gateway Configuration > ISDN BRI Channels
183
2 Click the extension of the channel that you want to modify.
3 Complete or change the fields, as necessary. See the online Help for more
information.
4 Enable the On Line check box to bring the channel on line.
The channel does not come online unless the card and the span are
online.
5 Click OK.
Viewing the Status of a Digital Line Card Channel
To view the status of an installed Digital Line Card:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Channels
■
PSTN Gateway Configuration > ISDN PRI Channels
■
PSTN Gateway Configuration > ISDN BRI Channels
2 Click the extension of the channel for which you want status information.
3 Click the Status tab.
4 From the Dialog Refresh drop-down list, select:
■
■
Manual — To refresh the Status window each time you click
Refresh Device.
A time interval (5, 10, 15, 30, or 60 seconds) — to refresh the
Status window at the specified intervals automatically.
5 Click Apply, and then click OK.
Viewing DSP (Digital Signal Processor) Details
To view DSP details:
1 Click PSTN Gateway Configuration > Digital Line Cards.
2 Click the MAC address of a Digital Line Card.
3 Click the Status tab.
4 In the DSP List, click a DSP ID to display the DSP Status window.
5 Click Close to close the DSP Status window.
184
CHAPTER 8: PSTN GATEWAY CONFIGURATION
Modifying IP Settings
You can modify the IP settings for a Digital Line Card to meet changing
requirements.
To use the NBX NetSet utility to modify IP settings, the line card must be
on the same subnetwork as the Call Processor.
The BRI and ATC/ALC daughter cards on the 3C10164D-ST card share the
same IP address. (There are no individual IP settings for channels on the
3C10164D-ST card, as they all share the same IP address.) Therefore,
depending on the configuration, you can change the IP address either of
these methods:
■
Click PSTN Gateway Configuration > Digital Line Cards, click an
extension, and then click the IP Settings tab.
■
Click Telephone Configuration > ATA, click an extension, and then
click the IP Settings tab.
If you change the IP address for any of the daughter cards, the IP address
of the other daughter cards changes as well. You can use this method
only when the Call Processor and the 3C10164D-ST are located on the
same subnetwork.
3C10165D E1 and 3C10116D T1 Digital Line Cards do not support DHCP
lease times of less than 20 minutes.
To modify the IP settings of a Digital Line Card:
1 Click PSTN Gateway Configuration > Digital Line Cards.
2 Click the MAC address of a Digital Line Card.
3 Click the IP Settings tab.
4 To assign IP addresses, enter the first address in the First IP Address field.
The system sequentially adds the remaining addresses. 3C10165D E1,
3C10116D T1, and 3C10164D BRI Digital Line Cards need only one IP
address.
Assigning IP Addresses One at a Time
To assign IP addresses one at a time for each channel on cards that
support this feature:
1 Click PSTN Gateway Configuration > Digital Line Cards.
2 Click the MAC address of a Digital Line Card.
3 Click the IP Settings tab.
Setting Up a Digital Line Card at a Remote Location
185
4 Click Assign Addresses Individually.
3C10165D E1, 3C10116D T1, and 3C10164D BRI Digital Line Cards need
only one IP address, therefore the Assign Addresses Individually button is
not present for these cards.
5 Enter the appropriate IP addresses for the channels.
6 Enter IP values in the Common Subnet Mask and Common Default
Gateway fields.
7 Click OK.
Removing a Digital
Line Card
You can remove a Digital Line Card at any time.
NOTE: Removing a Digital Line Card may affect your dial plan.
To remove a Digital Line Card:
1 Click PSTN Gateway Configuration > Digital Line Cards.
The T1/ISDN Board List shows the installed T1, ISDN PRI, and ISDN BRI
cards.
2 Select the card, or cards, that you want to delete and click Remove
Selected. To select all extensions, enable the Select check box.
3 Click OK when the system prompts you to confirm.
Setting Up a Digital
Line Card at a
Remote Location
Each 3C10116D T1, 3C10165D E1, or 3C10164D BRI Digital Line Card
can function as a standalone unit and communicate with the Call
Processor over a routed network.
To function as a remote card, the card must have the normal IP settings
(IP address, default gateway, and subnet mask), plus the IP address of the
Call Processor.
The 3C10116D, 3C10165D, and 3C10164D Digital Line Cards can use
static IP configuration or they can get their IP configuration from a DHCP
server. Auto Discovery downloads the Call Processor IP address to the
card. The card stores that information in its non-volatile memory.
3C10165D E1 and 3C10116D T1 Digital Line Cards do not support DHCP
lease times of less than 20 minutes.
186
CHAPTER 8: PSTN GATEWAY CONFIGURATION
To configure a Digital Line Card for remote operation:
1 Be sure your system is set for either Standard IP or IP On-the-Fly operation
(Click System-Wide Settings > IP Settings).
2 Install the Digital Line Card in a chassis. You do not need to power down
the chassis when you insert or remove cards.
To identify the card in the NBX NetSet utility, make a note of the card’s
MAC address printed on the component side of the card.
3 Enable Auto Discovery:
a Login to the NBX NetSet utility using the administrator login ID and
password.
b Click System-Wide Settings > Auto Discovery.
c Enable the Auto Discover Other Devices (including ATA, Digital Line
Cards & Analog Line Cards) check box, and then click Apply.
When you insert the card, it begins an initialization sequence. Once
the power up tests complete, the card communicates with the Call
Processor, which begins to update its database. Allow at least 3
minutes for both of these processes to complete. When the card
finishes its startup tests and establishes contact with its Call Processor,
the Call Processor status light on the card’s front panel turns green.
You can then disable the Auto Discover Other Devices (including ATA,
Digital Line Cards & Analog Line Cards) check box.
4 Click PSTN Gateway Configuration > Digital Line Cards to display a list of
available Digital Line Cards in the T1/ISDN Board List.
5 Click the MAC address of the card you just installed and then click the IP
Settings tab.
Unlike legacy Digital Line Cards, the 3C10165D E1, 3C10116D T1, and
3C10164D BRI Digital Line Cards use one IP address for all channels on
the card.
6 In the Manually Assigned IP Settings section, see the First IP Address,
Common Subnet Mask, and Common Default Gateway fields.
If you are using a static IP address for the card:
a Type the card’s IP address in the First IP Address field. The address must
be appropriate for the remote network where the card will eventually
reside.
b Type the subnet mask and default gateway values that are appropriate
for the remote network where the card will eventually reside.
Setting Up T1/E1 Logging
187
c Click OK.
The card will restart and go through its startup process. After the card
finishes its reboot process, proceed to step 7.
If the remote network where the card will eventually reside uses
DHCP to assign addresses:
a If the First IP Address, Common Subnet Mask, or Common Default
Gateway fields have an IP address, change each field to 0.0.0.0, and
then click Apply. After the card finishes its reboot process, proceed to
step 7.
b If the First IP Address, Common Subnet Mask, and Common Default
Gateway all show 0.0.0.0, assign an arbitrary IP address to any field,
and then click Apply. The card will restart and go through its startup
process again.
c When the card finishes its startup process, refresh the card’s IP Settings
window. You will see the arbitrary IP address that you assigned.
d Change each field to 0.0.0.0, and then click Apply. The card will
restart and go through its startup process again.
7 When the card finishes its startup process, it is set with the IP address of
its Call Processor. You can now move the card to its remote location
where it will use its saved Call Processor IP address to communicate with
the system.
Setting Up T1/E1
Logging
The 3C10116D T1 and 3C10165D E1 Digital Line Cards can generate
logging information. The system disk drive stores the TEP (T1, E1, Primary
Rate Interface) logs. Use the NBX NetSet utility to view, download, and
delete log files. Each card has a separate log, up to a maximum of five log
files. When a log reaches its maximum size of 5 MB, it begins to overwrite
the oldest data.
Because TEP logging has a performance cost, it is disabled by default. To
enable TEP logging and to receive help interpreting the log results,
contact your 3Com NBX Voice-Authorized Partner.
Viewing CSU State
Information and
Statistics
3C10165D E1, 3C10116D T1, and 3C101064D BRI cards have an
onboard channel service unit (CSU). Use the NBX NetSet utility to view
near end (local CSU) and far end (central office) state information and
statistics about each connected span.
188
CHAPTER 8: PSTN GATEWAY CONFIGURATION
To view CSU statistics:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
■
PSTN Gateway Configuration > ISDN BRI Spans
2 Click the MAC address of the span.
3 Click the Performance Data tab.
4 Click the appropriate button to choose the type and format the
performance data:
■
The system reports the T1 state information and statistics in two
formats - T1.231 format and AT&T TR54016 format. Both formats
report the same information but they use different terminology.
■
The system reports E1 state information and statistics in a single
format - ITU G.826.
■
The system reports G.826 near-end information about the
3C101064D BRI card.
The system samples performance statistics every 15 minutes and saves up
to 24-hours of data in 15-minute intervals. By default, the statistics
windows display data from the most recent 15-minute interval. To see
other intervals or data from the entire 24-hour period, use the Select
Interval controls. To display the currently selected data interval in a bar
chart, click Graph.
See the online Help for more information about the statistics categories.
T1.231 Near End
To view T1 Span near end statistics in T1.231 format:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click PSTN Gateway Configuration > T1 Spans.
3 Click a MAC address.
4 Click the Performance Data tab.
5 Click T.231 Near End.
6 See the online Help for details for more information.
Viewing CSU State Information and Statistics
T1.231 Far End
189
To view T1 Span far end statistics in T1.231 format:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click PSTN Gateway Configuration > T1 Spans.
3 Click a MAC address.
4 Click the Performance Data tab.
5 Click T.231 Far End.
6 See the online Help for details for more information.
TR54016 Near End
To view T1 Span near end statistics in TR54016 format:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click PSTN Gateway Configuration > T1 Spans.
3 Click a MAC address.
4 Click the Performance Data tab.
5 Click TR54016 Near End.
6 See the online Help for details for more information.
TR54016 Far-End
To view T1 Span far end statistics in TR54016 format:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click PSTN Gateway Configuration > T1 Spans.
3 Click a MAC address.
4 Click the Performance Data tab.
5 Click TR54016 Far End.
6 See the online Help for details for more information.
G.826 Near End
To view E1 Span near end statistics:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click PSTN Gateway Configuration > ISDN PRI Spans.
3 Click a MAC address.
190
CHAPTER 8: PSTN GATEWAY CONFIGURATION
4 Click the Performance Data tab.
5 Click G.826 Near End.
6 See the online Help for details for more information.
G.826 Far End
To view E1 Span far end statistics:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click PSTN Gateway Configuration > ISDN PRI Spans.
3 Click a MAC address.
4 Click the Performance Data tab.
5 Click G.826 Far End.
6 See the online Help for details for more information.
Using Loopback
Tests
The 3C10116D T1 and 3C10165D E1 cards can respond to commands
from the Central Office to loop back data at different points for
diagnostic purposes.
You use the NBX NetSet utility to enable each loopback test and to
initiate the Local and Framer loopback tests. The Central Office, or test
equipment that emulates Central Office equipment, must initiate Line
and Payload loopback tests.
For detailed logging information, you can enable TEP logging before you
enable loopback testing. However, to set up logging and interpret the
logs are advanced tasks that require help from a technical support
technician. You can see a simple pass/fail result by viewing the span
status, as described in “Enabling or Disabling Loopback Tests” on
page 191. To see the loopback test status of all spans, click PSTN
Gateway Configuration > Digital Line Cards > Config & Status Report.
The cards loop back data at the following points and with the following
characteristics:
■
Line Loopback — A loopback in which the signal returned toward
the source of the loopback command comprises the full 1.544 Mbits/s
signal with bit sequence integrity maintained, no change in framing,
and no removal of bipolar violations.
Using Loopback Tests
Enabling or Disabling
Loopback Tests
191
■
Local Loopback — An internal (within the framer) diagnostic
loopback in which the signal returned towards the source is framed.
■
Framer Loopback — An internal (within the framer) loopback that
tests the path up to where framing is introduced.
■
Payload Loopback — A loopback in which the signal returned
toward the source of the loopback command comprises the payload
of the received signal (with bit sequence integrity retained) and newly
generated ESF framing (not necessarily maintaining the integrity of the
channel timeslots, frames, or superframes of the received signal). The
newly generated ESF data link contains a valid performance report
message with a value of one in every LB-labeled bit position for the
duration of the loopback indicating the signal is the result of a payload
loopback.
You can use the NBX NetSet utility to enable or disable loopback test
support for 3C10116D T1 and 3C10165D E1 cards. By default, loopback
test support is disabled. After you enable loopback test support, you can
initiate the Local and Framer tests. The Central Office, or test equipment
emulating Central Office equipment, must initiate Line and Payload tests.
NOTE: If you enable one or more loopback tests, you will terminate any
active calls on all channels of the selected span and make that span
unavailable for calls until you disable loopback testing.
To enable or disable loopback support:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
2 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
3 Click the MAC address of a span.
4 Enable or disable the Enable Loopbacks check boxes as required and then
click Apply.
To view the results of Local and Framer loopback testing Span status
1 Login to the NBX NetSet utility using the administrator login ID and
password.
2 Click the appropriate link:
192
CHAPTER 8: PSTN GATEWAY CONFIGURATION
■
PSTN Gateway Configuration > T1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
3 Select the span and click Status.
A red alarm indicates that the test failed. No alarm indicates that the test
passed.
Obtaining a Dial
Tone from a PBX
System
To supply dial tone to your system, you can use:
■
A third-party PBX system with a digital (T1,E1, or BRI) interface
■
An NBX system, which connects to your system by means of a T1 line
When you establish the links between your NBX system and the PBX or
another NBX system, the signalling bits provide the dial tone.
If your NBX system connects to another NBX system, verify that the
Digital Line Card types are configured as T1. This method is not
supported if the Digital Line Card type is configured as ISDN.
1 Click PSTN Gateway Configuration > Digital Line Cards.
2 If the Digital Line Card type is ISDN, click the MAC address of the Digital
Line Card line.
3 In the Card Type drop-down list, select T1.
4 Click Apply.
Obtaining a Dial Tone from a PBX System
Figure 7 shows the pinout for the NBX T1 or E1 Digital Line Card.
Figure 7 T1 or E1 Connector Pinouts
9
8
7
6
T - TX Tip to PSTN
5
R - TX Ring to PSTN
4
3
T1 - RX Tip from PSTN
2
R1 - RX Ring from PSTN
1
10
Figure 8 shows the pinout for the NBX BRI Digital Line Card.
Figure 8 BRI Connector Pinouts
9
8
7
R - TX Ring to PSTN
6
R1 - RX Ring from PSTN
5
T1 - RX Tip from PSTN
4
T - TX Tip to PSTN
3
2
1
10
To find the pinout for the PBX T1 or E1 connector, see the PBX
documentation.
193
194
CHAPTER 8: PSTN GATEWAY CONFIGURATION
The transmit pair on the PBX system must connect to the receive pair on
the NBX system, and the transmit pair on the NBX system must connect
to the receive pair on the PBX system.
To avoid timing issues, either the NBX system or the PBX system must
supply the link timing. Typically, the PBX system emulates the Central
Office (CO), and the timing mode is set to Internal and provides the
clock. In this case, set the timing mode of the NBX system to Loop.
1 On the NBX system, log in to the NBX NetSet utility using the
administrator login ID and password.
2 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Spans
■
PSTN Gateway Configuration > ISDN PRI Spans
3 Click the appropriate span MAC address.
4 From the Timing Mode drop-down list, select Loop.
5 Click OK.
If the PBX system only supports Loop timing mode, then set the NBX
system timing mode to Internal.
A BRI line operates in TE mode, therefore the CO provides the timing
source.
If your configuration includes two NBX systems that are connected by a
T1 line, verify that one system’s timing mode is Internal and the other
system’s timing mode is Loop.
The PBX system must use a protocol that the NBX system supports.
Configure the NBX and PBX systems so that they both use the same
protocol.
If your NBX system connects to the PBX system by means of an E1 or BRI
line, you must configure the ISDN PRI or ISDN BRI spans.
1 On the NBX system, click the appropriate link:
■
PSTN Gateway Configuration > ISDN PRI Spans
■
PSTN Gateway Configuration > ISDN BRI Spans
2 Click the appropriate span MAC address.
Obtaining a Dial Tone from a PBX System
195
3 From the CO Switch Protocol drop-down list, select the appropriate
protocol.
4 Click OK.
If your NBX system connects to the PBX system by means of a T1 line, you
must configure the T1 Group settings:
1 On the NBX system, click PSTN Gateway Configuration > T1 Groups.
2 Click the appropriate group name.
3 Modify the fields appropriately. See the online Help for more information
about the fields.
4 Click OK.
196
CHAPTER 8: PSTN GATEWAY CONFIGURATION
9
NBX MESSAGING
This chapter describes how to configure these features of NBX
Messaging:
■
Group List
■
NBX Voice Mail
■
Auto Attendant
■
Voice Profile for Internet Mail
For more information about these topics and configuration procedures,
see the online Help.
If you install a third-party messaging system, the NBX Messaging window
is not available in the NBX NetSet utility. Follow the documentation for
your voice messaging system.
Group List
System group lists are lists of system users that all telephone users on the
system can see and use to send, or append and forward, a voice mail
message.
There are 99 System group lists that the system administrator creates and
manages. The system identifies System group lists using a two-digit
numbering scheme (01 – 99). You can:
■
Add System group lists
■
Modify System group lists
■
Remove System group lists
■
List the members of a System group list
■
Print a hardcopy of a System group list
■
Record a .WAV file of the System group name for identification
purposes
198
CHAPTER 9: NBX MESSAGING
The system provides a default System group list that includes all
telephone users on the system, and reserves Group ID of 0 for this group.
You can later exclude extensions such as conference phones,
greeting-only mailboxes, and collective mailboxes (ACD, hunt group, or
route point mailboxes) from this default list. Any System group list can
include or omit extensions from its list.
A telephone user can include a System group list in a Personal group list,
but a System group list cannot contain a Personal group list. For more
information about Personal group lists, see NetSet User Help.
NBX Voice Mail
You can configure system-wide settings for telephone users’ voice
mailboxes (click NBX Messaging). When you add new telephone users to
the system, the system creates a mailbox for each user. Telephone users
must record a name announcement, a personal greeting, and create a
password before they can retrieve their messages.
The system also creates mailboxes for extensions that are not associated
with a particular telephone, such as hunt group extension or a TAPI route.
Table 37 describes the fields on the NBX Voice Mail window.
Table 37 Voice Mail Settings
Field
Purpose
Maximum Number of The number of messages, regardless of length, that an
Messages
individual mailbox can have. A typical voice message lasts
approximately 20 to 30 seconds.
Default: 30 messages
Maximum: 512 messages
Minimum: 1 message
NBX Voice Mail
199
Table 37 Voice Mail Settings (continued)
Field
Purpose
New Message
Retention (days)
The maximum number of days that a new (unheard)
message remains in a voice mailbox before the system marks
it for deletion. However, the message is not deleted until
after this sequence of events:
■
The telephone user logs in.
■
The system informs the telephone user that the message
will be deleted.
■
The telephone user takes no action to prevent the
deletion of the message.
■
The telephone user logs out.
Default: 30 days
Maximum: 1826 days (5 years)
Minimum: 1 day
NOTE: When a telephone user listens to or saves a new
message, the system resets the time stamp for that message.
The Message Retention value controls when the system
marks the message for deletion.
Message Retention
(days)
The maximum number of days that a message remains in the
mailbox after a telephone user has listened to or saved it.
The system then marks the message for deletion. However,
the message is not deleted until after this sequence of
events:
■
The telephone user logs in.
■
The system informs the telephone user that the message
will be deleted.
■
The telephone user takes no action to prevent the
deletion of the message.
■
The telephone user logs out.
Default: 30 days
Maximum: 1826 days (5 years)
Minimum: 1 day
Maximum Incoming
Message Length
(minutes)
The maximum length, in minutes, for any one message.
Default: 5 minutes
Maximum: 10 minutes
Minimum: 1 minute
Voice Mail
Compression Format
The system uses ADPCM as the voice mail compression
format for voice prompts and messages.
200
CHAPTER 9: NBX MESSAGING
Table 37 Voice Mail Settings (continued)
Field
Purpose
On Disk Voice Mail
Format
The system uses ADPCM as the compression format for voice
prompts and mail on your disk.
Disable AA Transfer
Prompt
Enables or disables the transfer prompt (“Please hold while
your call is transferred”) when the Auto Attendant transfers
a call.
Default: Disabled
Additional Considerations
■
The maximum length of a voice mail message is 10 minutes. If
accumulated messages fill the system’s message storage space before
individual telephone users reach their capacity limits, either lower the
mailbox settings or upgrade your message storage option. If you
decrease mailbox settings, you do not affect data already in storage.
You can also encourage telephone users to delete old messages.
■
To view your system’s current message storage capacity, click Licensing
and Upgrades > Licenses. The system displays the number of NBX
Voice Mail/Auto Attendant ports and storage space (in hours on an
NBX 100 system). The number of ports defines how many voice mail
sessions and Auto Attendants can be in use simultaneously.
■
Each voice mail extension enables one voice message session. If all
voice mail extensions are in use, call behavior differs depending on the
operation. If the Attendant Console forwards calls to the Auto
Attendant, and all voice mail extensions are in use, an outside caller
hears ringing but no answer until an extension is free. If an internal
telephone user transfers a caller to voice mail, but no voice mail
extensions are available, the call rings back to the caller’s extension.
■
You can configure voice mail extensions, settings, passwords, and
off-site notification. The NBX NetSet utility also reports the status and
usage of voice mail ports and voice mail storage usage by telephone
user. For details, see these sections:
■
Voice Mail Extensions
■
Voice Mail Passwords
■
IMAP for Integrated Voice Mail
■
Off-site Notification
NBX Voice Mail
■
■
Status
■
Port Usage
■
User Usage
201
To support TTY device users, create an Auto Attendant that allows the
use of TTY voice mail prompts to access voice mail. TTY users dial the
extension of the Auto Attendant for TTY voice mail, press a button
that you map to the Transfer to TTY Voice Mail action, and then press
star (*) to navigate to the prompts for their extension number and
password. See “Adding an Accessible (TTY) Auto Attendant” on
page 221 for more information.
Voice Mail Extensions
The number of voice mail ports on your system defines the number of
voice mail sessions that can take place at one time. The default system
includes 4 voice mail ports. You can purchase a license for additional
capacity. Each voice mail port has an extension number. See “Extension
Settings Overview” on page 286 for more information.
Voice Mail Passwords
To retrieve voice messages, a telephone user must log on using the
extension number and password. The password, a 4-digit to 10-digit
number, allows access to Personal Settings in the NBX NetSet utility and
to voice mail from the telephone. The telephone user can change the
password from the telephone or by logging in to the NBX NetSet utility
The administrator can reset a user password to the user’s extension
number. See “Password Administration” on page 79 for information
about Security features.
For more information about the menus and features available to
telephone users, see an NBX telephone guide and the NBX NetSet utility
User Help.
IMAP for Integrated
Voice Mail
NBX Voice Mail uses an Internet Message Access Protocol (IMAP) server,
which enables telephone users to access and manage their voice
messages through any IMAP-compliant e-mail client. As the system
administrator, you may need to help telephone users to configure e-mail
clients.
Voice mail messages can be sent as mail messages with.WAV file
attachments. You double-click an attachment to activate the computer’s
media player, and the voice message plays through the speakers or
202
CHAPTER 9: NBX MESSAGING
earphones on your computer. After you listen to a message, it loses its
“new” status, but it remains on the server until you delete it using the
IMAP e-mail client, the telephone, or the Personal Settings window in the
NBX NetSet utility, or until the system deletes it when it is older than the
system limit (after a warning message). The computer used to receive
messages must support multimedia.
You cannot compose new voice mail messages through your IMAP e-mail
client. You must use your telephone.
To process both e-mail and voice mail on one computer, you need either
of the following:
■
An e-mail client that can connect to two servers
■
Two instances of the e-mail client
Setting Up an e-mail Client to Access Messages
Because each e-mail client has a unique configuration interface, the
following procedure is presented in general terms only. See your e-mail
client’s documentation to find out how to accomplish a specific task.
1 Be sure that the e-mail client can communicate with an IMAP 4 server.
Some versions of Microsoft Outlook and Outlook Express, Netscape, and
Eudora support IMAP. Check your e-mail program’s documentation to
find out if it supports IMAP.
2 Set the Incoming Mail Server to the IP address or to the host name of your
system.
Set the Outgoing Mail Server to the mail server in use for regular e-mail.
The NBX IMAP server cannot perform address translation, so you cannot
use the system as your company e-mail server.
3 If necessary, identify the server type as IMAP.
4 For the username, specify the user’s telephone extension number. For the
password, specify the user’s voice mail password.
Configurable
Operators
You can allow callers to forward their call to one of two configurable
operators when they reach a telephone user’s voice mailbox. You or the
telephone user can choose how to manage calls. The configurable
operators are:
NBX Voice Mail
203
■
System Operator — This is the standard System Operator for your
site.
■
Personal Operator — This is a destination other than the default
System Operator that would be appropriate for a call placed to you.
For example, a Personal Operator may be your executive assistant,
your cell phone, or a hunt group.
If you do not want to employ configurable operators, the default System
Operator (extension 501) remains in place.
The caller presses a number (the access digit) on the key pad to reach
either operator. The access digit for the System Operator is either 0 or 9;
the access digit for the Personal Operator is the digit you did not use for
the System Operator. (Access digits cannot be the same for both
operators.)
The two operators are functionally identical: either can be referenced as
the Personal Operator or the System Operator, depending on your site’s
requirements. For example, you could designate the extension for the
System Operator as your Personal Operator.
What Can You Assign As An Operator?
As the system administrator, you can assign any of the following as an
operator destination:
■
System extension
A system extension can be Auto Attendant or another extension
within your facility.
■
Hunt group
■
External telephone number
■
Virtual Tie Line (VTL) extension
Feature Support For Configurable Operators
The following features and desktop applications support Configurable
Operators:
■
Call Group mailboxes, hunt group mailboxes, and TAPI route points
support the Configurable Operators feature; otherwise, the defaults
apply.
■
Virtual Tie Lines (VTLs) — Personal operators can accept a VTL
extension.
204
CHAPTER 9: NBX MESSAGING
■
Phantom Mailboxes — Phantom mailboxes support the Configurable
Operators feature. The destination can be either an internal extension,
Auto Attendant, or voice mail.
■
Greeting-only Mailboxes — Greeting-only Mailboxes support the
Configurable Operators feature.
How the Configurable Operator Feature Works
When the system directs a caller from your voice mail to an operator that
you designated:
1 If you do not answer a call, the system invokes your voice mail.
2 The caller listens to your pre-recorded voice mail message, which includes
the instruction to press an access digit (0 or 9) to reach the appropriate
operator.
When you employ a configurable operator, you must re-record your
personal voice mail greeting to explain to callers that an operator is
available to them if they press the appropriate access digit during the
voice mail greeting.
3 The caller presses 0 or 9.
4 The system redirects the call to the operator that you designated.
The caller can leave a message, then press 0 or 9 to transfer to a
configured operator.
Configuring Operator Destinations
To configure system default operator destinations:
1 Log on to NetSet using the administrator login ID and password.
2 Click NBX Messaging > Configure.
3 Click the Personal Operator tab.
The editable fields display the current system default values for System
Operator and Personal Operator.
You cannot leave the system default values for the operators as null. Also,
the text string for an operator destination cannot exceed 16 characters.
4 Edit the operator numbers and the access digits as appropriate.
5 Click the Apply button to make the changes and keep this window open,
or click the OK button to make the changes and close the window.
NBX Voice Mail
Off-site Notification
205
Off-site Notification can notify telephone users by pager, e-mail, or
telephone when they receive a new voice mail message. Telephone users
can specify the methods by which they receive notification.
You can configure these system-wide Off-site Notification settings:
■
Enable or disable Off-site Notification for the entire system
■
Set the maximum number of out-calling ports
■
Assign an out-dialing prefix for Off-site Notification
To configure Off-site Notification, click NBX Messaging > Configure and
click the Off-site Notification tab.
Table 38 provides details on Off-site Notification fields.
Table 38
Off-site Notification Fields
Field
Purpose
Offsite Notification
Enabled
Enables Off-site Notification throughout the system. By
default, Off-site Notification is disabled.
When you enable Off-site Notification, you must also enable
it for:
■
Class of Service Settings. See Class of Service (CoS) on
page 132.
■
The telephone user’s personal settings. See “Off-Site
Notification” in an NBX telephone guide for more
information.
Max Out-calling Ports The number of voice mail ports available for simultaneous
use by Off-site Notification. You can configure this
parameter for up to the number of voice mail ports licensed
for the system. The system is shipped with 4 ports; purchase
an upgrade license to enable additional ports.
Out-dialing Prefix
A prefix used by every call made by Off-site Notification.
If this setting is empty, the call uses only the information
specified by the telephone user.
Notes About Off-site Notification
■
To allow telephone users to take advantage of Enable Off-site
Notification, you must perform these three steps:
■
Click NBX Messaging > Configure and click the Off-site Notification
tab to enable Off-site Notification system wide.
206
CHAPTER 9: NBX MESSAGING
■
■
Verify that the individual telephone user’s extension has been
enabled for Off-site Notification.
■
Before Off-site Notification can send e-mail, define an SMTP Domain
Name, and one or more valid Domain Name Servers (click
System-Wide Settings > IP Settings).
■
When you use Off-site Notification:
■
■
■
■
Status
Click User Configuration > Class of Service and click the CoS Group
Name to enable Off-site Notification in the Class of Service
settings.
If you choose Pager or Voice Mail as the first notification method,
the system notifies you only of the first new message you receive
after the time you have most recently logged in to your voice
mailbox. The system does not notify you each time you receive a
new message. The next time you log on to your voice mailbox,
Off-site Notification is re-enabled.
If you choose EMail as the first notification method, you receive a
notice for each message. The system attaches the message to the
e-mail as a .WAV file. If you configure any method in any of the
remaining four attempt lines, the system also attempts each
specified method for each new voice mail message.
If you configure more than one notification attempts, configure
them in order. For example, if you configure three attempts,
configure them on lines 1 through 3, without unconfigured lines in
between.
If you disable NBX Messaging in favor of another messaging
application, the Offsite Notification is unavailable.
To view the status of all voice mail ports on this system, click NBX
Messaging > Configure and click the Status tab.
You can also reset a voice mail port. Select the extension, or extensions,
that you want to reset and click Reset. To select all extensions, enable the
Select check box.
Table 39 explains the information in the Status window.
Table 39 Fields in the Status Window
Column
Purpose
Extension
The extension that is associated with the voice mail port.
NBX Voice Mail
207
Table 39 Fields in the Status Window (continued)
Column
Purpose
Name
The name that is associated with the voice mail port.
Used By
The person or device that is using the voice mail port.
Values:
In Use (Seconds)
■
Extension number, name — The extension number and
name of an internal telephone user that is using the voice
mail port.
■
Auto Attendant — The Automated Attendant is using the
port.
■
Blank — The port is not being used. The system displays
Idle in the In Use column.
The length of time, in seconds, that the voice mail port has
been in use.
If the port is not in use, the system displays Idle.
On Hold
Indicates whether the voice mail port is on hold. The system
places voice mail ports on hold in the same way that it places
a call on hold.
Values: Yes, No
Port Usage
To find out how busy the system’s voice mail ports are, and whether
additional ports may be necessary, click NBX Messaging > Configure, and
then click the Port Usage tab. See the online Help for details about the
report.
The system displays parameters in the Port Usage report in red to alert
you that a problem exists. For example, if “Missed messages caused by
full mailboxes” changes to red, you may need to increase the maximum
number of messages allowed for each mailbox.
User Usage
To find out about user impact on the voice mail system, click NBX
Messaging > Configure, and then click the User Usage tab.
The User Usage report provides the current number of new and saved
voice mail messages for each telephone user and calculates the amount
of storage each telephone user’s messages consume. This report lists any
type of mailbox, including telephone, phantom, TAPI route point, and
hunt group mailboxes.
208
CHAPTER 9: NBX MESSAGING
Deleting User Voice Mail
From the User Usage report, you can also delete the voice mail messages
for a selected telephone user. Select the extension, or extensions, from
which you want to delete voice mail and click Delete VM. To select all
extensions, enable the Select check box.
The time the system requires to delete a telephone user’s voice mail
depends on the number of voice mail messages in the user’s mailbox.
Auto Attendant
The NBX Messaging system includes an Auto Attendant that answers
incoming calls. The Auto Attendant includes a series of recorded
messages (prompts) that describe actions that a caller can take to access
individual services. You can customize the menu structure and record or
import your own prompts to fit the system to your business needs. For
example, you can configure an Auto Attendant to support users of
teletypewriter (TTY) devices for hearing impaired callers.
This section provides information about these topics:
Overview of Auto
Attendant Features
■
Overview of Auto Attendant Features
■
Adding an Auto Attendant
■
Adding an Accessible (TTY) Auto Attendant
■
Managing Auto Attendants
■
Voice Application Setup Utility
■
Testing the Auto Attendant
The Auto Attendant is the centerpiece of the voice mail system. You can
create and configure Auto Attendants, and can record or import
messages and prompts to direct the actions of callers.
Use the NBX NetSet utility to administer and configure these Auto
Attendant features:
■
Multiple Auto Attendants — The system supports multiple,
independent Auto Attendants. You can assign different Auto
Attendants to different extensions, inbound lines or DID numbers. See
“Adding an Auto Attendant” on page 210 for more information.
■
Multiple-Level Menus — Each Auto Attendant can support a main
menu and up to 19 levels of submenus. You to configure an
Auto Attendant
209
automated system in which inbound callers can select specific
departments or groups, and then further select subgroups or
individuals. See “Prompt Menus” on page 213 for more information.
■
Voice Prompts — To the caller, the time-dependent greeting, main
menu prompt, and submenu prompt are integrated into the Auto
Attendant system. You can customize the system by recording or
importing voice prompts in a time-dependent greeting main menu, or
submenu. Depending on the time of day and selections that the caller
makes, the caller hears the appropriate prompts and receives
appropriate directions.
■
Default Time-out — If a caller does not respond to the Auto
Attendant prompts (for example, a caller that uses a rotary telephone),
the system routes the call to a designated time-out destination. See
“Prompt Menus” on page 213 for more information.
If you do not specify a valid time-out destination for an Auto Attendant,
the system drops a call when it reaches the time-out value.
■
Shortcuts — Callers can press a shortcut button to bypass an entire
greeting or prompt and move directly to a function, such as leaving a
voice mail message.
■
Dialing by Extension or Name — A caller can reach a person by
dialing the person’s extension. The system plays the announcement of
each person identified as a possible match and asks the caller to pick
one.
■
Dialing by First Name or Last Name — A caller can reach a person
by dialing the person’s name on the telephone keypad. After the caller
selects the Name Directory option, Auto Attendant prompts the caller
to select whether to use the first-name method or last-name method.
When the caller begins to enter the name on the keypad, Auto
Attendant performs a database lookup and prompts the caller with
the possible matches. The caller selects the appropriate name, and
Auto Attendant transfers the call to the selected telephone user.
■
Automatic Activation — The system can activate automatically
according to the Business Hours settings (see “Business Hours” on
page 32), or after an incoming call exceeds a set number of rings.
■
Routing Calls to Specific Auto Attendants — You can use the dial
plan to map Auto Attendants to specific analog telephone extensions.
This enables the system to route incoming calls directly to a specific
Auto Attendant.
210
CHAPTER 9: NBX MESSAGING
■
Voice Application Setup Utility — From the 3Com Business
Telephone, you can use the Auto Attendant Voice Application Setup
utility to set up these Auto Attendant features:
■
Button actions
■
Time-dependent greetings and schedule
■
Main menu greeting
■
Administrator’s Auto Attendant password
See “Voice Application Setup Utility” on page 225 for more
information.
■
Adding an Auto
Attendant
Accessible prompts for teletypewriter (TTY) devices — Voice mail
and Auto Attendant prompts are available as TTY tones. You can
configure an Auto Attendant menu to allow telephone users to access
prompts that are compatible with their TTY devices. TTY device users
can configure their Call Forward Settings to the extension of this Auto
Attendant. See “Adding an Accessible (TTY) Auto Attendant” on
page 221 for more information.
The system includes two Auto Attendants: the Default Menu (extension
500), which manages incoming calls, and the VoiceMail Menu (extension
501), for employee access to voice mail. You cannot delete these two
Auto Attendants. The default Auto Attendant processes calls as soon as
you install the system. When you add a new Auto Attendant, you are
adding a blank Auto Attendant, which you can configure.
To add a new Auto Attendant, click NBX Messaging > Auto Attendant >
Add.
Table 40 describes the fields and checkbox on the Add Auto Attendant
Menu window.
Table 40 Add Auto Attendant Menu Fields
Field
Purpose
Name
Enter a name for the new Auto Attendant.
Auto Attendant
211
Table 40 Add Auto Attendant Menu Fields (continued)
Field
Purpose
Extension
The system automatically assigns the next available extension
when you add a new Auto Attendant. You can change the
extension number to an unused number that falls within the
Auto Attendant extension range of your dial plan.
Default range:
3-digit dial plan: 500–599
4-digit dial plan: 5500–5599
For both 3-digit and 4-digit dial plans, the default Auto
Attendant is extension 500 and the voice mail Attendant is
extension 501.
Maximum number of Select the number of times the Auto Attendant prompt
prompt repeats
repeats. You can select a number from 1 through 99.
Default: 3
NOTE: If the time-out action for the Auto Attendant menu
tree is set to Disabled, the system disconnects the call after
the prompt repeats the maximum number of times. To
ensure that forwarded calls eventually reach a valid
destination, configure a time-out action for each Auto
Attendant menu tree.
NOTE: If you configure the Auto Attendant for TTY voice
mail, set this field to a higher value to allow for delays that
occur between responses to prompts if a caller uses a TTY
relay service. Multiple prompt repetitions prevent the system
from disconnecting calls prematurely.
Use System-wide
Greetings checkbox
Enable this checkbox so that the system uses all three
system-wide greetings (Morning, Afternoon and Evening) by
default. To enable or disable individual system-wide
greetings for a particular Auto Attendant, click NBX
Messaging > Auto Attendant, click a specific extension, and
then click the TD Greetings tab.
After you add or modify an Auto Attendant, you can configure the
following features:
■
Play/Record Extension
■
Time-dependent Greetings
■
Prompt Menus
■
Auto Attendant Buttons
Play/Record Extension
The Play/Record Extension identifies the telephone on which you can
work interactively with the NBX NetSet utility to record and listen to Auto
212
CHAPTER 9: NBX MESSAGING
Attendant prompts. Typically, this is the extension of the person who
configures and administers the Auto Attendant. An Auto Attendant
prompt is an audio file (.WAV) that is associated with a specific Auto
Attendant. It describes the actions a caller can take.
When you click the button in the NBX NetSet utility to record or play a
prompt, the extension rings. When you answer it, you either hear the
prompt you selected to play or you are prompted to record a prompt.
You cannot customize any greetings or prompts until you specify this
extension.
To specify a play/record extension, click these links:
■
NBX Messaging > Auto Attendant.
■
NBX Messaging > Auto Attendant and then click the System Wide
Greetings tab.
■
NBX Messaging > Auto Attendant, a specific extension, and then click
the Prompt or TD Greetings tab.
Time-dependent Greetings
The system clock and the greeting schedule control when the system
changes from one time-dependent greeting to the next. For example, the
morning greeting may start at 12 midnight, the afternoon greeting at
noon, and the evening greeting at 6 p.m. If you enable time-dependent
greetings, the caller hears the current active greeting before the main
menu prompt.
You can create time-dependent greetings for all Auto Attendants in your
system. An example of this system-wide greeting may be “Good
morning.” To record or to import system-wide time-dependent greetings
and define the times during which they play, click NBX Messaging > Auto
Attendant and click the System-Wide Greetings tab.
You can also create and schedule time-dependent greetings for individual
Auto Attendants. These greetings can be up to five minutes long. To
record, import, or schedule customized time-dependent greetings, click
NBX Messaging > Auto Attendant, click a specific Auto Attendant
extension and then click the TD Greetings tab.
Auto Attendant
213
Prompt Menus
You can use a main menu and submenus of prompts to direct callers to
individuals and services in your organization. To configure prompt menus
for each Auto Attendant, click NBX Messaging > Auto Attendant, click a
specific extension and then click the Menu Tree tab. The Menu Tree
window consists of 13 button rows that you use to assign actions to the
key pad buttons (see “Auto Attendant Buttons” on page 217). Be sure to
define the menu time-out behavior so that the system automatically
routes calls to a time-out destination if a caller does not respond to the
Auto Attendant prompts (for example, a caller that uses a rotary
telephone).
If the time-out action for the Auto Attendant menu tree is set to
Disabled, the system disconnects the call after the prompt repeats the
maximum number of times. To ensure that forwarded calls eventually
reach a valid destination, configure a time-out action for each Auto
Attendant menu tree.
Main Menus If you enable a time-dependent greeting, the main menu
prompt follows it. The main menu prompt describes all Auto Attendant
options and can be up to five minutes long. The default Auto Attendant
main menu prompt states:
“If you know the extension of the party you want to reach, you may enter
it at any time. To reach the name directory, press 9. To reach the Auto
Attendant, press 0 or remain on the line. Thank you for calling.”
By default, the Auto Attendant main menu provides callers with the
functions that Table 41 describes.
Table 41 Auto Attendant Default Configuration
Button
Action
Numbers
These buttons allow callers to dial these user extensions:
4-digit dial plan: 1000–3999
NOTE: If you import any 3-digit plan to a system with a factory default
4-digit dial plan, you must manually specify any 3-digit extension ranges
that are not set by the imported plan.
3-digit dial plan: 100–449
NOTE: The NBX 100 system is shipped with a 3-digit dial plan. If you
import any 4-digit plan, you must manually specify any 4-digit extension
ranges that are not set by the imported plan.
214
CHAPTER 9: NBX MESSAGING
Table 41 Auto Attendant Default Configuration (continued)
Button
Action
9
Connects to the Name Directory.
0
Transfers to the extension specified in the menu tree for the Auto
Attendant, usually the extension of the receptionist’s telephone. The
default extension is:
4-digit dial plan: 1000
3-digit dial plan: 100
*
Prompts the caller for a mailbox number and then transfers the call
directly to the specified mailbox.
#
Exits from the system.
T/O
A menu time-out action; transfers to the extension specified in the menu
tree for the Auto Attendant, usually the extension of the receptionist’s
telephone. The default extension is:
4-digit dial plan: 1000
3-digit dial plan: 100
NOTE: Always configure a timeout action for an Auto Attendant top
level menu. The system will disconnect a call if the call times out and
there is no valid action defined.
To create a main menu, click NBX Messaging > Auto Attendant, click a
specific Auto Attendant extension, and then click the Menu Tree tab. To
create or import voice prompts, click NBX Messaging > Auto Attendant,
click a specific Auto Attendant extension, and then click the Prompt tab.
See the online Help for procedures to create menus and prompts.
Submenus An Auto Attendant main menu can branch to submenus to
keep the main menu brief, and to give the caller a variety of choices. Each
submenu has a prompt that informs the caller of the option that each key
pad button provides.
If you have a large organization, the caller may have to enter several
digits and listen to several submenus before reaching the person or
department. For example, the caller may hear:
”To reach our Sales Department, press 1. For Technical
Support, press 2...”
The caller selects option 1 for sales and hears:
”For European Sales, press 1. For North American sales, press
2.”
Auto Attendant
215
The caller requires North American sales, presses 2, and is connected to a
sales hunt group.
To configure submenus, click NBX Messaging > Auto Attendant, click a
specific Auto Attendant extension, and then click the Menu Tree tab. See
the online Help for procedures to set up submenus.
For an example that uses submenus, see “Three Greetings, a Main Menu,
and a Submenu” in the next section.
Examples
These examples illustrate some typical Auto Attendant systems. They
illustrate the kind of information that you may include in your
time-dependent greetings, main menu prompts, and submenu prompts.
No Greetings Figure 9 shows the simplest configuration. The
time-dependent greetings are disabled; the Main Menu contains all of the
prompts. In Example 1, callers hear the same message no matter what
time they call.
Figure 9 No Time-dependent Greetings, All Prompts in Main Menu
Morning
Greeting
disabled
Afternoon
Greeting
disabled
Evening
Greeting
disabled
Main
Menu
“Thank you for calling XYZ Corporation. If you know your party’s
extension, you can enter it now. To reach our Sales department,
press 3. For Marketing and Public Relations, press 4. To reach the
company directory, press 9.”
In this example, the main menu is configured to map button 3 to a Sales
submenu and button 4 to a Marketing and Public Relations submenu.
Button 9 is mapped to the Name Directory.
216
CHAPTER 9: NBX MESSAGING
Three Greetings and a Main Menu Figure 10 shows a simple Auto
Attendant that uses time-dependent greetings to provide different
messages for different times of the day.
Figure 10 Three Time-dependent Greetings and Main Menu
Morning
Greeting
8 am...
Afternoon
Greeting
noon
Evening
Greeting
6 pm
Main
Menu
“Good morning. Thank you for calling XYZ Corporation. If you know
your party’s extension, you can enter it now. To speak to an operator,
press 0.”
“Good afternoon. Thank you for calling XYZ Corporation. If you know
your party’s extension, you can enter it now. To speak to an operator,
press 0.”
“Good evening. Thank you for calling XYZ Corporation. Our normal
business hours are 8 a.m. to 6 p.m. Monday through Friday. If you know
your party’s extension, you can enter it now.”
“To reach our Sales department, press 3. For Marketing and Public
Relations, press 4. To leave a message in the general mailbox,
press 6. To reach the company directory, press 9.”
In this example, the morning greeting starts at 8 a.m. and is active until
the afternoon greeting begins at noon. The evening greeting begins at
6 p.m.
The function that you allocate to a button on the keypad remains the
same throughout the day.
Three Greetings, a Main Menu, and a Submenu Figure 11 shows
an example that uses time-dependent greetings, a Main Menu, and a
Submenu.
Auto Attendant
217
Figure 11 Three Time-dependent Greetings, a Main Menu and a Submenu
Morning
Greeting
“Good morning.”
12 am...
Afternoon
Greeting
“Good afternoon.”
noon
Evening
Greeting
“Good evening.”
6 pm
Main
Menu
“Thank you for calling XYZ Corporation. If you know your party’s
extension, you may dial it now. To speak to an operator, press 0. For
Sales, press 3. For Support, press 4. To leave a message in the genera
mailbox, press 5. To reach the company directory, press 9.”
Sub
Menu
“You have reached the customer support line. To speak with a support
technician about a new issue, press 1. For returns and warranty
information, press 2. To check the status of an existing support issue,
press 3. To return to the previous menu, press star.”
This example uses time-dependent greetings to greet callers according to
the time of day. The main menu prompt presents callers with options for
reaching the operator, specific departments, or the company directory of
names. It also uses a submenu to direct callers to subgroups within the
Support department.
Auto Attendant Buttons
You can configure the key pad button actions presented to a caller by the
Auto Attendant (click NBX Messaging > Auto Attendant, click a specific
Auto Attendant extension, and then click the Menu Tree tab). For
examples of how you can use prompts and greetings in an Auto
Attendant, see “Examples” on page 215.
Table 42 describes the Menu Tree fields.
Table 42 Menu Tree
Field
Purpose
Button
Lists the buttons on the telephone key pad.
218
CHAPTER 9: NBX MESSAGING
Table 42 Menu Tree (continued)
Field
Purpose
Task Description
Describes the key pad button operation. If you assign the
Enter Submenu action to the button, this description is used
as the Submenu name.
Action
Contains a drop-down list box that lists the actions you can
assign to a key pad button. The Auto Attendant prompts
callers to press buttons to perform specific actions. You must
configure the Menu Tree to so that each button performs
the proper action.
For a complete list of button actions, see Table 43.
Value
Describes the value associated with each key pad button
action. For a complete list of key pad button actions, see
Table 43.
You can assign keypad actions to each button on a typical telephone key
pad, 0 through 9, #, and *.
Table 43 describes the actions you can assign to buttons. Most systems
use no more than five action choices to avoid confusing callers. If you
need to present more than five choices, use submenus to configure these
additional options. See “Submenus” on page 214.
To create an unannounced option, map a button without creating a
corresponding prompt. Callers do not hear a message that the choice is
available.
Auto Attendant
219
Table 43 Button Actions
Action
Description
Disabled
The system takes no action when the telephone user presses
this button. A prompt announces invalid key.
If assigned as a menu time-out action (T/O), Disabled either
leaves the system or goes to a parent menu, depending on
where the attendant is in the menu hierarchy.
NOTE: If you set this field to 1 and the time-out action for
the Auto Attendant menu tree to Disabled, the system
disconnects a call forwarded to the Auto Attendant because
the forwarding party always hears a portion of the Auto
Attendant prompt. Likewise, if you set this field to 2 or 3
and the time-out action for the Auto Attendant Menu Tree
to Disabled, the system disconnects the forwarded call if the
forwarding party stays on the line long enough to hear at
least a portion of the final repeated prompt. To ensure that
forwarded calls eventually reach a valid destination,
configure a time-out action for each Auto Attendant menu
tree.
Value — Not used.
Name Directory
Allows a caller to spell a person’s name on the keypad. The
system matches the letters that the caller enters to a Last
Name in the list of User Profiles. If the system finds more
than three matches, it prompts the caller to enter more
letters. When the system narrows the choice to three or
fewer, it offers the caller a choice by playing the recorded
name greeting of each choice. During a search, the system
ignores any User Profile that does not have a recorded
greeting.
Value — Not used.
System Disconnect
Allows the caller to have the system close the connection.
This feature can save time for callers who call into the
system using a calling card. By having the system disconnect
them instead of breaking the connection themselves, callers
can make other calls without re-entering all of their calling
card information. To activate System Disconnect, the
telephone user must press the key defined in the menu and
then, when prompted, the key defined in the Value box.
Typically, you do not include these instructions in the Auto
Attendant prompt, which is heard by all callers. Instead, you
make your system users aware of this sequence.
Value — Any of 0-9, #, *
Transfer to Voice Mail Allows callers to leave a voice message for a person without
ringing that person’s phone, or allows telephone users to
call in and listen to their voice mail from a remote location.
Value — Not used.
220
CHAPTER 9: NBX MESSAGING
Table 43 Button Actions (continued)
Action
Description
Transfer to TTY Voice
Mail
Functions the same as the Transfer to Voice Mail action,
however, callers can access voice mail prompts that are
compatible with their TTY devices. See Adding an Accessible
(TTY) Auto Attendant on page 221 for more information.
Value — Not used
Exit Menu
Available in submenus only. Allows the caller to return to
the next menu up in the menu tree.
Value — Not used
Prompted Transfer
Instructs the caller to press a button before dialing a known
extension. The prompt may state: “If you know your party’s
extension, press 5, and then dial the extension.“
Value — Not used.
Reserved in Dial Plan
Interprets a specified button as the first number of an
extension. For example, in the default 4-digit dial plan,
extensions begin at 1000, so you could not use 1 as an
option for an Auto Attendant menu.
Value — Not used
Single Digit Transfer
Allows a caller to press a specific button to reach a specific
destination.
For example, you may assign button 6 to a hunt group
extension in the Sales Department. In the menu prompt, you
can record: “To reach our Sales Department,
press 6.” You can also use Single Digit Transfer to
specify a destination, typically the Attendant Console
extension, for the time-out option (T/O).
By default, Single Digit Transfer can forward calls only to
internal extension numbers. To transfer calls to an external
number, you must first alter Table 2 of the dial plan
(Incoming Table) to specify the external number.
Value — Any valid extension
NOTE: Be careful when you use Dial Plan Table 2 to allow access to PSTN ports,
which can allow toll fraud.
Auto Attendant
221
Table 43 Button Actions (continued)
Action
Description
Enter Submenu
Puts the caller into a submenu of options. When you assign
the Enter Submenu action to a button and then click Apply,
the system displays a down-arrow button to the right of the
row. Click this down-arrow button to configure the
submenu that you want to associate with the main menu.
The entry in the Task Description field for this button
becomes the submenu name.
Submenu button actions include “Exit menu” to allow
callers to return to the next highest menu. Otherwise,
submenu button actions are identical with main menu
button actions.
Each menu can have up to 20 levels of submenus.
For an example that uses submenus, see “Three Greetings, a
Main Menu, and a Submenu” on page 216.
Value — Not used
Activating Changes
After you modify a greeting or prompt (or any Auto Attendant setting),
you must activate these changes in the Auto Attendant before they
become effective. The !> characters next to an Auto Attendant in the
Auto Attendant list indicate that you must activate the Auto Attendant.
To activate changes, click NBX Messaging > Auto Attendant, select a
specific Auto Attendant extension, and click Activate.
If you do not click Activate, the system does not implement the changes
when you click Apply.
Adding an Accessible
(TTY) Auto Attendant
You can connect TTY devices to the system through a single port Analog
Terminal Adapter (3C10400 and 3C10400B) or a 4-port Analog Terminal
Card (3C10117C).
You can set up the system so that you:
■
Dedicate an extension for TTY access only. Only TTY callers dial this
extension. Users who want to hear voice prompts must dial another
extension.
■
Configure an extension that lets callers choose voice or TTY prompts.
When callers dial this extension, the Auto Attendant prompt provides
an option to transfer to TTY compatible voice mail.
222
CHAPTER 9: NBX MESSAGING
■
Configure user’s call forward settings to forward calls to TTY
prompted voice mail.
To dedicate an extension to an Auto Attendant for use with TTY devices:
1 Verify that you have connected a TTY device to the system through an
ATA or an ATC.
2 Use the NetSet utility and the TTY device, or third-party software, to
create a TTY compatible audio file (.wav) to use for the main menu
prompt. For example, the prompt can state “To leave a TTY message
press star, for assistance press 0 or stay on the line.”
See the online Help for information about how to use the NetSet utility to
record audio files.
3 Log on to NetSet using the administrator login ID and password.
4 Click NBX Messaging > Auto Attendant.
5 Click Add.
6 Configure an Auto Attendant and click OK.
Set the Maximum number of prompt repeats to a higher value than the
default to allow for delays that occur between responses to prompts if a
caller uses a TTY relay service. Multiple prompt repetitions prevent the
system from disconnecting calls prematurely. The maximum number of
prompt repetitions is 99.
7 Click the extension of the Auto Attendant and then click the Menu Tree
tab.
8 Configure the menu hierarchy for TTY voice mail and click Apply.
For example, from the Action drop-down list, select Transfer to TTY Voice
Mail to correspond to the star (*) button, and configure the zero(0)
button and T/O to correspond to a TTY operator extension.
9 Click the Prompt tab.
10 Import and then select the TTY .wav file that you created, which will
provide the main menu prompt.
If the system retrieved the file but was not able to use it, these are some
possible reasons:
■
The file format is not acceptable. There are three file formats that are
acceptable to the system:
■
IMA ADPCM (8 KHz sampling rate, 4 bits per sample, monophonic)
■
PC (8 KHz sampling rate, 16 bits per sample, monophonic)
Auto Attendant
■
■
223
CCITT uLaw (8 KHz sampling rate, 8 bits per sample, monophonic)
The file format is acceptable, but the file is a raw binary file and does
not contain the necessary file header information.
11 Click OK.
12 Select the extension of the new Auto Attendant and then click Activate,
which makes the Auto Attendant available for use with TTY devices.
To configure TTY user settings so that the system forwards incoming
telephone calls to the Auto Attendant for TTY devices:
1 Click User Configuration > Users.
2 Click a user’s extension.
3 Click the Settings tab.
4 Click Call Forward.
5 Enable the Forward to phone number radio button and type the number
for the Auto Attendant for TTY devices.
Telephone users also can configure their Call Forward Settings from the
NetSet utility.
Auto Attendant for TTY Voice Mail Considerations
Managing Auto
Attendants
■
SIP-mode systems do not support direct connections of TTY devices.
■
The Auto Attendant Name Directory option is not available to TTY
device users.
■
TTY users cannot use the Name Directory option when they create or
send messages from the voice mail menu.
■
The system codecs may not be compatible with turbo or fast mode
TTY modems.
This section describes additional ways in which you can manage Auto
Attendants.
■
Modifying an Auto Attendant
■
Removing an Auto Attendant
■
Restoring Auto Attendant Greetings
224
CHAPTER 9: NBX MESSAGING
Modifying an Auto Attendant
To modify an Auto Attendant, click NBX Messaging > Auto Attendant
and click a specific Auto Attendant extension.
Table 40 describes the fields and checkbox tin the Modify Auto Attendant
Menu window.
Table 44 Modify Auto Attendant Menu Dialog Box
Field
Purpose
Name
Edit the name of the Auto Attendant.
Extension
Edit the extension number by changing it to an unused
number that falls within the Auto Attendant extension range
of your dial plan.
Default range:
3-digit dial plan: 500–599
4-digit dial plan: 5500–5599
For both 3-digit and 4-digit dial plans, the default Auto
Attendant is extension 500 and the voice mail Attendant is
extension 501.
Maximum number of Select the number of times the Auto Attendant prompt
prompt repeats
repeats. You can select a number from 1 through 99.
Default: 3
NOTE: If the time-out action for the Auto Attendant menu
tree is set to Disabled, the system disconnects the call after
the prompt repeats the maximum number of times. To
ensure that forwarded calls eventually reach a valid
destination, configure a time-out action for each Auto
Attendant menu tree.
NOTE: If you configure the Auto Attendant for TTY voice
mail, set this field to a higher value to allow for delays that
occur between responses to prompts if a caller uses a TTY
relay service. Multiple prompt repetitions prevent the system
from disconnecting calls prematurely.
Use System-wide
Greetings
Enable this checkbox so that the system uses all three
system-wide greetings (Morning, Afternoon and Evening) by
default. To enable or disable individual system-wide
greetings for a particular Auto Attendant, click NBX
Messaging > Auto Attendant, click a specific extension, and
then click the TD Greetings tab.
Auto Attendant
225
Removing an Auto Attendant
To remove an Auto Attendant:
1 Click NBX Messaging > Auto Attendant.
2 Select the extension, or extensions, that you want to remove and click
Remove Selected. To select all extensions, enable the Select check box.
3 Click OK.
You cannot remove the Default Menu Auto Attendant or the Voice Mail
Auto Attendant.
Restoring Auto Attendant Greetings
You can restore the greetings to their default values:
■
aamenu.wav and aamenu2.wav prompts
■
System-wide Morning, Afternoon and Evening greetings
This feature restores all of these prompts and greetings at the same time.
No other user-defined prompt is affected.
To restore greetings, select NBX Messaging > Auto Attendant and then
click Restore-AA-Greetings.
Voice Application
Setup Utility
The Auto Attendant Voice Application Setup utility provides a series of
voice prompts to guide you in configuring your Auto Attendant. You can
access the setup utility through any 3Com Business Telephone.
The Voice Application Setup utility is useful for making short-term
changes to your Auto Attendant. For example, if you must close your
office because of bad weather, you can edit the main menu and direct
callers to a message telling them that your office is closed. However,
because you cannot use the Voice Application Setup to configure
submenus, use the NBX NetSet utility. See “Submenus” on page 214.
Although the setup utility lets you perform tasks in any sequence, 3Com
recommends this sequence when setting up the system for first time:
1 Plan the system.
2 Create profiles (phantom mailboxes and destination extensions).
3 Start the Auto Attendant Setup utility.
226
CHAPTER 9: NBX MESSAGING
4 Change the Auto Attendant Setup utility password.
5 Assign actions to key pad buttons.
6 Record greetings and main menu prompts.
7 Set the greeting schedule.
8 Review and test the system.
Using the Voice Application Setup Utility
From a 3Com telephone, you can use the Auto Attendant Setup Utility.
Follow these steps:
1 Lift the telephone handset, and then press the MSG button to access the
Voice Mail system.
2 At the voice mail password prompt, press *.
3 At the voice mail extension prompt, dial 999 if you are using a 3-digit dial
plan or 9999 if you are using a 4-digit dial plan.
4 Enter the Auto Attendant password. The default password is 0000. 3Com
recommends that you change this password.
0000 press 1 to assign actions to dial pad key, 9 to record
greetings, schedules, change password
5 Follow prompts to assign key pad button actions, record and play back
greetings, change the schedule (morning, afternoon, and evening) and
change the Auto Attendant password.
Testing the Auto
Attendant
Before using your system, 3Com strongly recommends that you review
and test it to verify that all features work as you intend. Use this checklist
to verify that your system is ready:
■
Do your recorded prompts match your key pad button actions?
You can define key pad button actions through the NBX NetSet utility
(see “Auto Attendant Buttons” on page 217) or through the Voice
Application Setup utility.
■
Do your time-dependent greetings become active at the times you
want?
If not, you can use the NBX NetSet utility (see “Time-dependent
Greetings” on page 212) or the Voice Application Setup utility to
change the start times of your morning, afternoon, and evening
greetings.
Voice Profile for Internet Mail
Voice Profile for
Internet Mail
227
■
Do your single-digit transfers and transfer to the general mailbox take
a caller to a valid destination?
■
When callers reach a mailbox of a single-digit transfer and transfer to
the general mailbox, do they hear an appropriate greeting?
■
Is someone responsible for checking messages sent to single-digit
transfers and transfer to the general mailbox?
■
Do you get an “invalid key” message when you press a button that
does not have an action assigned?
■
Does the Auto Attendant time-out action perform the correct action?
Always have a time-out action for a top-level Auto Attendant menu
tree. Leaving the time-out action set to Disabled, the default, can
result in calls being disconnected.
■
Do all of your submenu prompts match the submenu key pad button
actions?
Voice Profile for Internet Mail (VPIM) is an optional feature. Telephone
users can use VPIM to send voice mail to a user on any voice mail system
that is VPIM-compliant.
The system transmits VPIM voice mail messages by attaching them to
e-mail messages. The system then uses SMTP (Simple Mail Transfer
Protocol) or ESMTP (Extended Simple Mail Transfer Protocol) to send the
e-mail message and its VPIM attachment.
VPIM uses an SMTP server that is embedded in the operating system. To
avoid abuse by spammers, always protect an SMTP server with a firewall.
Configure the firewall to allow access to UDP port 25 on the system only
from valid VPIM systems that need to deliver VPIM messages to the
telephone system. The NBX SMTP server is started only when the system
has a valid license for VPIM.
VPIM is an optional component that requires a license, which appears in
the NBX NetSet Licenses window as Internet Voice Messaging License.
You must enter a license key through the NBX NetSet utility before you
can configure and use VPIM.
228
CHAPTER 9: NBX MESSAGING
Use the NBX NetSet utility to configure VPIM settings, check the status of
VPIM queues, and obtain statistics of recent VPIM activity. See these
sections for more information:
■
Control Parameters
■
Operations Management
■
Statistics
■
Advanced Settings
■
Configuring Domain Name Server Information
For information about how to configure the dial plan to use VPIM, see
“Dial Plan Configurations and VPIM” on page 306.
Control Parameters
To configure VPIM control parameters, click NBX Messaging > VPIM.
Table 45 explains the VPIM control parameter fields and their purpose.
Table 45 VPIM Tab Fields
Field
Purpose
Maximum message size (Kbs)
Controls the size of incoming messages from other
sites. If a message is larger than the specified
value, the system rejects it. The default value
represents a voice mail message approximately 4
to 5 minutes in length.
Default: 3000 KB
Minimum: 500 KB
Maximum: 5000 KB
Time between send attempts
(Minutes)
For outgoing messages, the system may not be
able to contact the target system on the first
attempt. If so, the system attempts to contact the
target system later. To change the time between
attempts to send a voice mail message, change
this number.
Default: 15 minutes
Minimum: 1 minute
Maximum: 60 minutes
Voice Profile for Internet Mail
229
Table 45 VPIM Tab Fields (continued)
Field
Purpose
Maximum number of send
attempts
Specifies the number of times the system attempts
to connect to the target system.
After the specified number of send attempts, the
system returns the voice mail message to the
sender’s voice mail box with an indication that the
message could not be sent.
Default: 4 attempts
Minimum: 1 attempt
Maximum: 10 attempts
Maximum time before message Default: 60 minutes
expires (Minutes)
Operations
Management
To manage the queue of outgoing voice mail messages, click NBX
Messaging > VPIM and then click the Operations Management tab.
Table 46 describes the fields in this window.
Some commands require that you start or stop operations. For example,
to remove a message from the queue, first stop operations. Similarly,
unless you start operations or they are currently running, you cannot use
the “Send all messages now” command.
Table 46 Operations Management Dialog Box Fields
Field
Purpose
Operations status
The status of the queue of outgoing voice mail messages.
Possible values: Ready, Starting, Processing, Stopped
Number of outgoing
messages
The number of messages in the outgoing queue when this
dialog box was last accessed or refreshed.
Outgoing Messages
Remove Selected
Select the voice mail message, or messages, that you want
to delete and click Remove Selected. To select all voice mail
messages, enable the Select check box.
Time Waiting
The time that the voice mail message has been waiting in
the queue.
# Attempts
The remaining number of attempts to send the message.
Sender
The IP address and extension of the telephone user who
sent the voice mail message.
230
CHAPTER 9: NBX MESSAGING
Table 46 Operations Management Dialog Box Fields (continued)
Field
Destination
Purpose
The IP address and extension to which the voice mail
message is to be sent.
If a message has multiple destinations, the system lists the
first destination followed by three dots.
Example: 1057@192.168.15.135...
Send all messages now The system attempts to send all messages immediately, and
changes the status of each successfully sent message to
Sent.
Send all messages now The system attempts to send all messages in the queue and
and then delete them deletes each message that is sent successfully.
If a message cannot be sent, it is also deleted.
Statistics
Delete all messages
now
The system empties the queue of all messages
Stop operations
Stops the queue if it is currently active.
Start operations
Starts the queue if it is stopped.
The Statistics window allows you to view the most recent statistics for
voice mail messages.
To view statistics, select NBX Messaging > VPIM and click the Statistics
tab.
Table 47 lists the fields and explains their purpose.
Table 47 Statistics Window Fields
Field
Purpose
Incoming Messages
Total messages received
by system
The number of messages received by this system from
voice mailboxes on other systems
Total messages delivered
to user mailboxes
The number of voice mail messages delivered to user
voice mailboxes on this system. If this number is smaller
than the total number of messages received, some
messages have not yet been delivered.
Outgoing Messages
Total messages submitted The number of messages submitted by telephone users
for external delivery
of this system for delivery to voice mailboxes on other
systems
Voice Profile for Internet Mail
231
Table 47 Statistics Window Fields (continued)
Field
Purpose
Total messages delivered
to external recipients
The number of messages for which a confirmation of
delivery has been received.
Total messages returned
to sender on failed
delivery
The number of messages that have been returned
because they could not be delivered.
Failed Outgoing
Messages
The number of messages that never left the queue
either because every attempt to deliver them failed and
the retry limit was reached, or because the type of
failure caused the retry limit to be ignored (example: a
non-existent address would be tried only once).
If a message had multiple destinations, the first
destination is listed, and three dots are displayed
immediately after the extension number.
Example: 1057@192.168.15.135...
Date/Time
The date and time that the message was originally
submitted for delivery
# Attempts
The number of attempts that the system has made to
send each message
Sender
The person on the local system who created and sent
the voice mail message
Destination
The defined target for the voice mail message
Reason
The reason for the most recent failure to deliver the
message
Reset and Reboot Times
Last reset command
The date and time of the last reset command. Sets all
VPIM statistics to 0 (zero) and deletes all messages from
the Failed Outgoing Messages queue.
If this field’s date and time are more recent than Last
system reboot, then the system began to collect the
currently displayed statistics at this date and time.
Last system reboot
The date and time of the most recent reboot of the
system. A system reboot resets all VPIM statistics to 0
(zero).
If this field’s date and time are more recent than Last
reset command, then the system began to collect the
currently displayed statistics at this date and time.
Advanced Settings
The system transmits VPIM voice mail messages by attaching them to
e-mail messages that are sent using SMTP (Simple Mail Transfer Protocol).
232
CHAPTER 9: NBX MESSAGING
You can control the behavior of SMTP and how it sends e-mail messages
with VPIM attachments.
To configure SMTP settings, click NBX Messaging > VPIM and then click
the Advanced Settings tab.
Table 48 lists the fields and describes their purpose.
Table 48 VPIM Advanced Settings Dialog Box
Field
Purpose
SMTP OK response
The amount of time that the local system waits for
an acknowledgement of a From message.
After the local system sends a MAIL command
specifying the sender of the message, it waits for
acknowledgement from the other site. The
acknowledgement is an OK message.
Minimum: 5 minutes
Default: 5 minutes
SMTP HELO response
The amount of time that the local system waits for
an acknowledgement of a HELO message.
After the greeting, the local system sends either a
HELO (or EHLO to get ESMTP) message to identify
itself. The other site then responds with an
acknowledgement of that message.
Minimum: None defined.
Default: 5 minutes
SMTP EHLO response
The amount of time that the local system waits for
an acknowledgement of a EHLO message.
After the greeting, the local system sends either a
HELO (or EHLO to get ESMTP) message to identify
itself. The other site then responds with an
acknowledgement of that message.
Minimum: 0 minutes
Default: 5 minutes
Voice Profile for Internet Mail
233
Table 48 VPIM Advanced Settings Dialog Box (continued)
Field
Purpose
SMTP MAIL response
The amount of time that the local system waits for
an acknowledgement of a MAIL command.
After the local system sends out a MAIL command
along with the From information, it waits for a
response from the other site to indicate that the
MAIL command was received.
Minimum: 5 minutes
Default: 5 minutes
SMTP RCPT response
The time that the local system waits for an
acknowledgement of a RCPT command.
When the local system receives and SMTP or ESMTP
message, it returns a RCPT command to the sending
system for each recipient listed in the To: field.
Minimum: 5 minutes
Default: 5 minutes
SMTP DATA response
The time that the local system waits for an
acknowledgement of a DATA command.
After the local system has specified all of the
recipient information, it sends a DATA command to
indicate that it is ready to send the mail message
itself. It then waits for the other site to acknowledge
the DATA command.
Minimum: 2 minutes
Default: 2 minutes
SMTP DATA END response
The time that the local system waits, after sending
the entire message, for an acknowledgement from
the other site that the message was received.
After the local system sends the entire message, it
sends a single dot (ascii code 056) to the other site. It
then waits for an acknowledgement from the other
site that the dot has been received.
Minimum: 10 minutes
Default: 10 minutes
234
CHAPTER 9: NBX MESSAGING
Table 48 VPIM Advanced Settings Dialog Box (continued)
Field
Purpose
SMTP RSET response
The time that the local system waits for an
acknowledgement of a RSET command.
Maintaining a cached connection between the local
system and any other site requires additional system
resources compared to a non-cached connection. If
connection caching is enabled, the local system waits
for the defined time-out period and if no message is
received, it sends a RSET command to the other site.
Minimum: None defined.
Default: 10 minutes
SMTP QUIT response
The time that the local system waits for an
acknowledgement of the QUIT command.
When the local system transmits a message and
wants to break the connection, it sends a QUIT
command. It then waits for the other site to
acknowledge the QUIT command. When the
acknowledgement arrives, or when the time-out
value is reached, whichever comes first, the local
system breaks the connection.
Minimum: None defined.
Default: 5 minutes
Configuring Domain
Name Server
Information
When the SMTP utility attempts to send e-mail, it must be able to resolve
a host name within an e-mail address and find out the proper IP address
from that name. Domain Name Servers on the Internet perform this
function. You can configure up to three DNS entries with the NBX NetSet
utility. The system uses the second and third entries if the first or second
cannot be reached. To configure DNS information in the NBX NetSet
utility:
1 Click System-Wide Settings > IP Settings.
2 In the Primary DNS, Secondary DNS, and Tertiary DNS fields, type the IP
addresses of three Domain Name Servers. If you have the IP address of
only one server, type it in the Primary DNS field. If you have the IP address
of only two servers, type them in the Primary and Secondary DNS fields.
Click OK.
10
SIP-MODE OPERATIONS
NBX systems that use Session Initiation Protocol (SIP) are described in
these topics:
■
Overview of SIP Mode on the NBX Platform
■
Other Applications Support
■
Enabling and Configuring SIP Mode
■
Adding Telephone Users and Devices
For more information about these topics and configuration procedures,
see the online Help.
Overview of SIP
Mode on the NBX
Platform
A system running release R6.0 or higher can operate using two forms of
Call Control /Setup.
■
3Com call control mode — The traditional call control employed by
all previous releases of the system software.
■
SIP mode — 3Com telephones and line cards communicate with the
system using 3Com call control mode. SIP devices, such as the 3Com
3108 Wireless Telephone, generic SIP phones, and SIP gateways and
servers, use IETF RFC 3261 (SIP: Session Initiation Protocol) to
communicate with the system.
When you configure a system to run in SIP mode, all audio is carried
using RFC 1889 (RTP: A Transport Protocol for Real-Time Applications) as
the underlying communications infrastructure. Some older devices do not
support RTP and are disabled when you enable SIP mode operations. For
more information about supported devices in SIP mode, see “Device
Support Details” on page 238.
SIP Mode Operations
A SIP mode system has these operating characteristics, limitations, and
features that differ from a 3Com call control mode system:
236
CHAPTER 10: SIP-MODE OPERATIONS
■
SIP mode is not supported on the NBX 100. See Table 50 on page 240
for detailed system platform support information.
■
SIP mode on an NBX system means standard SIP support (RFC 3261)
with no proprietary extensions to SIP. Third-party telephone features
that are dependent on non-standard SIP will not work. A SIP mode
system does not support secure SIP signaling or secure RTP. It does not
support NAT, firewalls, or RTP relay. Communication is over UDP only.
■
A SIP mode system uses Standard IP as the network protocol. If you
enable SIP on a system that uses Ethernet mode or IP on the Fly, the
system automatically switches to Standard IP. You typically configure a
DHCP server to provide IP information to devices and configure Option
184 on the DHCP server to provide the Call Processor IP address.
■
A SIP mode system can interoperate with any other SIP endpoint,
including gateways, devices, and SIP-enabled applications. For
example, a SIP mode system is able to interoperate with the 3Com
VCX Telephony System, a SIP-based system designed to support large
distributed enterprises.
■
3Com Telephones connected to a SIP mode system behave the same
as they do when running under 3Com call control mode except for
these differences:
■
■
■
■
Conferences can include up to three parties, the conference
originator, and two other conference parties, either internal or
external. The limit is four parties on a system that is not running in
SIP mode. However, the number of simultaneous conference
sessions supported in SIP mode increases beyond the current limit
of 12. For conferences that require more than 3 parties, you can
configure the optional 3Com IP Conferencing Module.
The WhisperPage feature is not available on a system running in SIP
mode.
An external messaging application, typically the 3Com IP
Messaging Module, provides Voice mail and Auto Attendant
menus and prompts, and Music-on-Hold. NBX Messaging is
disabled when you enable SIP.
These devices can participate in a conference call:
■
3Com 3108 Wireless Telephone
■
Generic SIP telephones
■
3Com pcXset Soft Telephone Client
Overview of SIP Mode on the NBX Platform
■
237
Analog telephones
However, you cannot use these devices to add extensions to a
conference.
■
The Auto Discovery feature works for 3Com phones (except the 3108
Wireless Telephone), and cards and devices. You must configure SIP
devices and gateways, and the 3Com 3108 Wireless Telephone
manually. Typically, you use NetSet utility to add the telephone user
and user extension to the system database. You specify the extension
and the IP, and authentication parameters that the SIP device uses to
communicate with the Call Processor on the SIP device itself.
■
NBX Messaging does not work on a system running in SIP mode. A SIP
mode system must have an external messaging system to provide
voice mail and Auto Attendant services. 3Com recommends the
3Com IP Messaging Module. On a system running 3Com call control
mode, you need an optional license to run an external messaging
system. If you enable SIP mode on a system, no external messaging
license is required.
■
A telephone user can login at different phones (hot desking), but only
one login at a time is allowed. If a telephone user is on a call, and then
logs into another phone, the system disconnects the first call. This
feature works only on generic SIP telephones and the 3Com 3108
Wireless Telephone. This feature is not available on a system that is
running 3Com call control mode.
■
Button mapping is not supported for the 3Com 3108 Wireless
Telephone or generic SIP telephones. You cannot map a CO Line to a
generic SIP telephone or a 3108 Wireless Telephone.
■
The 3Com 3108 Wireless Telephone or generic SIP telephones cannot
be bridged extensions.
■
Virtual Tie Lines are not available on a system running in SIP mode.
However, you can achieve the same result, connecting different
systems, by configuring each system that is running SIP mode as a
trusted SIP interface. A trusted SIP interface can include SIP proxies,
SIP applications, SIP gateways, and any other third-party SIP device,
including 3Com VCX IP Telephony systems. Each NBX system can use
the same IP Messaging Module.
■
A Trusted SIP Interface connection between an NBX system and a
3Com VCX telephone system can share the same IP Messaging
Module. However, the automatic mailbox creation process can work
for only one type of system. Typically, you use automatic mailbox
238
CHAPTER 10: SIP-MODE OPERATIONS
creation for the enterprise-class VCX system and manual mailbox
creation for the NBX system or systems.
■
Paging is supported on 3Com phones (except the 3Com 3108
Wireless Telephone) with SIP enabled. Generic SIP phones and the
3108 Wireless Telephone can neither initiate nor receive pages.
■
There are restrictions on the Automatic Call Distribution (ACD) feature
on a SIP mode system. See “SIP Mode and ACD” on page 243.
■
Directory services are not supported on generic SIP phones and 3Com
3108 Wireless Telephones.
■
SIP mode systems support 3Com 1105 and 3105 Attendant Console
operations. However, only call status, not line status, of SIP endpoints
is available for SIP telephones.
■
A TAPI application is only able to monitor generic SIP phones and the
3Com 3108 Wireless telephone.
A SIP mode system supports E911 functionality. However, for 911 calls,
you must manually configure generic SIP telephones and the 3Com 3108
Wireless Telephone to use the alternate SIP gateway address if the Call
Processor is not available. For generic SIP telephones, this behavior is
specific to the telephone, and it is the responsibility of telephone to
provide this functionality.
Device Support
Details
There are important distinctions to keep in mind when you consider how
devices connected to a SIP mode system behave:
■
SIP-only telephones such the 3Com 3108 Wireless Telephone and
generic, third-party SIP telephones can use many of the standard
telephony features through feature codes.
■
Legacy telephones, analog adapters, and line cards that do not
support RTP become disabled if they are connected to a system that is
running in SIP mode. When you enable SIP mode, the system displays
a report that lists any device that will be disabled. Table 49 shows the
devices that can support the full feature code set:
Table 49
Devices Supported in SIP Mode Operation
Device
Part Number
2102B/PE Business Phone
3C10226B/PE or 3C10228IRB/PE
1102B/PE Business Phone
3C10281B/PE
2101B/PE Basic Phone
3C10248B/PE
Overview of SIP Mode on the NBX Platform
Table 49
239
Devices Supported in SIP Mode Operation
Device
Part Number
3100 Entry Phone
3C10399A and 3C10399B
3101 and 3101SP Basic Phone
3C10401A and 3C10401SPKRA
3C10401B and 3C10401SPKRB
3102 and 3102B Business Phone
3C10402A and 3C10402B
3103 Manager's Phone
3C10403A and 3C10403B
3106C and 3107C Cordless Phones
3C10406 and 3C10407
3108 Wireless Telephone
3C10408
pcXset Soft Telephone Client R6.0 and
higher
3C10316 (single user license) and
3C10154 (site license)
1105 Attendant Console
3C10123A and 3C10124
3105 Attendant Console
3C10405A and 3C10405B
1-port Analog Terminal Adapter
3C10400A and 3C10400B
V3000 Analog ports
3C10600A and 3C10600B
V3000 BRI-ST ports
3C10601A
V3001 Analog ports
3CR10800
V3001 BRI-ST ports
3CR10801
V3001R Analog ports
3C10602A
V3001R BRI-ST ports
3C10603A
4-port Analog Terminal Card*
3C10117C
Card*
3C10114C
Analog Line
Card*
3C10116D
E1 Digital Line Card*
3C10165D
External Paging Device
N/A
NBX Media Driver R6.0 and higher
3C10319
Polycom Soundstation IP 4000
2200-06632-001
T1 Digital Line
* SIP mode systems do not support earlier versions of this card.
Feature Support
The 3Com devices listed in Table 49 can take advantage of the full
feature set that the system offers. Generic SIP telephones and the 3Com
3108 Wireless Telephone support some features through feature codes.
However, any feature code that must be activated while a call is in
progress is not supported.
See the NBX Feature Codes Guide for SIP Telephones for complete
information about how generic SIP telephones and the 3Com 3108
240
CHAPTER 10: SIP-MODE OPERATIONS
Wireless Telephone interact with the standard features. The guide is
available to telephone users and system administrators through the NBX
NetSet utility.
Hot Desking
Hot desking refers to the ability of a SIP telephone user to enter the
username and password on a different telephone, and have that
telephone come up as his or her own. This is one advantage of using a SIP
telephone.
However, there are several things to remember in a hot-desking scenario:
Platforms Supported
■
To support hot desking, the system de-registers the telephone user
from the previous telephone, but the previous telephone must not be
in use in order for the de-registration to take place.
■
The behavior of the system services may be different for the telephone
user if the new telephone is a different type.
■
The telephone user can use the NBX NetSet interface to change the
extension of the new telephone, but it is the responsibility of the
telephone user to change the extension on the telephone itself to
effect synchronization. Otherwise, the system cannot authenticate the
telephone and it is inoperative.
Because SIP mode operation increases memory demands on the system,
V3000, V3001, and V5000 systems support SIP mode operations only if
they have the optional memory upgrade installed. Table 50 lists the
system platforms, and their memory configurations, that are capable of
operating in SIP mode:
Table 50 System Platforms Supporting SIP Mode
Call Processor Model
SIP Capable?
NBX 100
No
V5000 - 128 MB
No
V5000 - 256 MB
Yes
V5000 - 384 MB
Yes
V3000 Analog or BRI-ST - 128 MB
No
V3000 Analog or BRI-ST - 640 MB
Yes
V3001 Analog or BRI-ST - 256 MB
No
V3001 Analog or BRI-ST - 512 MB
Yes
Overview of SIP Mode on the NBX Platform
241
Table 50 System Platforms Supporting SIP Mode
Call Processor Model
SIP Capable?
V3001R
Yes
To find out if your V3000, V3001, or V5000 system includes the memory
upgrade:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > System Identity.
3 Verify that Memory Upgrade Installed is set to YES.
Licensing and
Resource Limits
This section describes the system resource limits on a SIP mode system.
Sessions
A SIP session is an end-to-end communications path between two
endpoints. A session includes a voice mail transaction, a public or
restricted conference, or a gateway path. There is a maximum limit of
150 concurrent sessions on a SIP mode system.
When you configure a SIP mode system, be careful about how many
simultaneous sessions you allow for each feature for which you can
configure sessions. For some NetSet SIP-related functions, such as
messaging and conference configuration, you must estimate the number
of simultaneous sessions that the feature is likely to manage. For
example, if you estimate that the system is likely to manage up to 30
simultaneous voice mail messages, the system blocks the thirty-first
message.
The number of simultaneous sessions that you specify for a feature
counts against the total device limit for the system. You can find out the
number of devices used against the total number in the Usage Report
(click Licenses and Upgrades > Licenses). V3000, V3001, and V5000
systems with expanded memory and V3001R systems can be licensed to
manage up to 1500 devices.
Devices
Devices count against the number of licenses allowed in a group (Group
0 – 4). Each telephone consumes one license from the appropriate
group's limit.
242
CHAPTER 10: SIP-MODE OPERATIONS
Gateways
Gateways do not count against the device limit itself. Instead, the number
of sessions on the gateway is counted. For example, if you create a
gateway with three sessions, those three sessions immediately count
against the device limit. You add gateways as Trusted SIP Interfaces.
SIP Mode License Requirements
This section details the licensing requirements for a system running in SIP
mode. You do not need a license to enable SIP mode operation or for
external messaging or conferencing applications.
■
A 3Com 3108 Wireless Telephone uses a Group 1 license and counts
as one system device.
■
Each third-party SIP phone uses one Group 1 license and counts as
one system device.
■
Depending on the type of telephone, each 3Com telephone uses a
Group 0,1, or 2 license and it counts as one system device.
■
A third-party PSTN gateway requires one system device license for
each audio path trusted interface.
SIP gateways, SIP proxies, and third-party SIP applications can be
assigned as trusted interfaces.
At initial configuration, each trusted interface must assign the
maximum number of audio paths that it can have open concurrently.
Each audio path is tracked against the licensed system capacity device
limit of up to 1500 devices. For example, if the trusted interface is
configured for thirty audio paths, the thirty-first request receives a
busy tone or is redirected to another Dial Plan route, if one is
configured and available.
■
Dial Plan
Considerations
Multi-vendor SIP soft trunks (such as Cisco VIC Cards,
VCX-to-NBX-to-VCX dial plans, and MCI SIP trunks) require one
system device license for each audio path trusted end point.
The Dial Plan consists of the rules that govern calling behaviors. The NBX
NetSet utility automatically updates your dial plan for most SIP related
changes. However, you must manually update the dial plan if you add a
3Com IP Conferencing Module to the system.
Other Applications Support
243
The default dial plan includes an additional default entry, SIP Connection
Ports, in the routing table. A SIP Connection Port identifies the route for a
call going to a SIP gateway or to another trusted device.
SIP Mode and ACD
Generic SIP telephones and the 3Com 3108 Wireless Telephone do not
fully support the ACD feature. The following applies to SIP-only devices
and their interaction with ACD:
■
A generic SIP phone and the 3108 Wireless Telephone cannot be a
member of an ACD group.
■
A generic SIP phone and the 3108 Wireless Telephone cannot be a
member of a Hunt group or a Calling group.
ACD Features Not Available on SIP Mode Systems
These ACD features are not available on a SIP mode system:
Other Applications
Support
Call Log Support
SNMP Support
SysLog Support
■
In Queue Digit processing
■
Queue Exit announcement
■
Estimated Wait time Announcement
■
Business and custom hours
■
Shifts
■
Wrap-Up Time
■
Closed announcement
This section lists how SIP-mode supports other applications on the
system.
SIP telephones themselves provide call log information. That is, the
system does not communicate information related to call logs to SIP
endpoints.
The system stores information about SIP telephones, which is delivered to
the SNMP manager by means of proxy information managed by the
system.
A SIP mode system supports Syslog functionality.
244
CHAPTER 10: SIP-MODE OPERATIONS
CDR Support
Enabling and
Configuring SIP
Mode
For SIP devices, call data records may display Not reachable as the
release cause if the device is offline. CDR provides the complete URL
rather than extensions only for SIP telephones.
To enable a system to run in SIP mode is a one-step process that has
extensive affects on the system. There is a significant impact on existing
telephone users if you convert an existing operating NBX system to SIP
mode, particularly on Auto Attendants and voice mail. Because NBX
Messaging is not available on an NBX system operating in SIP mode, you
must reconfigure those services. All existing voice mail configuration and
messages are lost. In addition, many older 3Com telephones and devices
cannot support SIP and will be disabled on a SIP mode system.
The following topics describe how to enable and configure SIP and add
devices:
Install and Configure
the System for SIP
Mode
■
Install and Configure the System for SIP Mode
■
Enable SIP Mode
■
Disable SIP Mode
■
Add Messaging
■
Create Mailboxes
■
Force Mailbox Creation
■
Configure Auto Attendants
■
Configure Music on Hold
■
Configure ACD Delayed Announcements
■
Add Trusted SIP Interfaces
■
Add an Optional IP Conferencing Module
To install and configure the system for SIP mode:
■
Follow the procedures in the NBX Installation Guide to power up the
system and configure network connectivity.
■
Configure the system-wide settings, such as the system date and time,
business identity settings, and so forth.
■
Install the 3Com IP Messaging Module, which is described in the IP
Messaging Installation Guide (click Downloads > Documentation).
Enabling and Configuring SIP Mode
Enable SIP Mode
245
To enable SIP mode on your system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Enable Features System-Wide.
3 Enable the Enable SIP check box, and then click Apply.
4 Click OK.
At this point the system performs these steps:
■
Backs up the database.
■
Reboots automatically after the backup is complete.
■
Enables Standard IP.
The system running in SIP mode must use Standard IP as its network
protocol. The system disables IP On-The-Fly and Ethernet and makes
them unavailable. All telephones operate at Layer 3.
■
Enables the Third-Party Messaging option in System-Wide Settings as
part of the reboot process.
The Third Party Messaging option does not require a license in SIP
mode. The NBX Messaging option is disabled and unavailable in SIP
mode.
Disable SIP Mode
To convert a SIP mode system to a 3Com call control mode system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Enable Features System-Wide.
3 Clear the Enable SIP check box, and then click Apply.
The system queries if you want to restore the database from a
previously-stored backup. If you do not select a previously-stored backup,
the system uses the default backup database when it reboots.
When you enabled SIP mode, the system created a backup database for
you. If you disable SIP mode, you can use that same backup database to
restore the system to its pre-SIP mode state. However, if you use the
default backup database, the system will not be restored to the state it
was in before you converted the system to SIP mode because non-RTP
device data cannot be restored by default.
4 Click OK.
246
CHAPTER 10: SIP-MODE OPERATIONS
At this point, the system:
■
Backs up the database.
■
Reboots automatically after the backup is complete.
■
Enables Ethernet as a part of the reboot process. (You can change this
setting.)
■
Enables NBX Messaging.
The system now reverts to 3Com Call Control mode. SIP-only devices no
longer function, and the database has changed.
Add Messaging
A system running in SIP mode must have an external messaging system.
3Com recommends that you use the 3Com IP Messaging Module, which
has been enhanced to support system operations.
After you configure IP Messaging on the system, you must configure the
services — Auto Attendants, Music on Hold, and ACD announcements.
For information about how to install and configure services on the 3Com
IP Messaging Module, see the IP Messaging Module Installation Guide,
which is available through the NBX NetSet utility (click Downloads >
Documentation). Other IP Messaging documentation for administrators
and end users is available on the NBX Resource Pack.
To add IP Messaging to a system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > IP Messaging.
3 Type the extension used by the system for IP Messaging. This extension
must be an unused extension on the system in the range of external
extensions, which is defined as 6000-7999 by default in a 4-digit dial
plan. The system adds the extension to the *0003 extension list in the dial
plan.
Every physical and virtual device on a system must have an extension. The
IP Messaging extension identifies the IP Messaging Module, a trusted SIP
interface. To verify the dial plan change, click Dial Plan > Extension List,
and then click extension list *0003.
4 Type a description for the IP Messaging Module.
Enabling and Configuring SIP Mode
247
5 Type the eth0 IP address for the IP Messaging Module. NBX
configurations do not use the eth1 interface.
6 Type a port number for IP Messaging. A SIP endpoint is identified by the
IP and port combination.
The default port, 5060, is listed in the Internet Assigned Number
Authority port list as a Registered Port for SIP.
7 Type the maximum number of simultaneous sessions. This value is less
than or equal to the number of available IPM licenses. Each session
requires one system device license. See “Licensing and Resource Limits”
on page 241 for more information.
8 Type the voice mail extension that end users can dial to access the Auto
Attendant.
9 Type the interval for subscriber data updates to the IP Messaging Module.
Subscriber data uploads only if extension numbers are unique. System
subscriber data is written to an XML file at the specified interval. See the
next topic, “Create Mailboxes” for further details.
10 Type the password (the default password is nice), that is used to access
the IP Messaging Module.
11 Click Send Update Now for an immediate upload of subscriber data to
the IP Messaging Module.
12 Click OK or Apply to save your changes.
When you click Apply, the system adds the IP Messaging Module as a
trusted endpoint. Click SIP Applications > Trusted SIP Interfaces to verify.
Create Mailboxes
When a new telephone user, ACD group, hunt group, or TAPI route point
is created, the NBX system communicates with the IP Messaging Module,
which then creates a new mailbox. The communication method that the
NBX system uses to pass information to the IP Messaging Module does
not occur in real time.
The IP Messaging Module only creates mailboxes. It does not update or
delete mailboxes.
In the NBX NetSet utility, you define the interval for the system to create
and transfer an XML file, which includes the necessary information to
create mailboxes, to the IP Messaging Module (SIP Applications > IP
Messaging).
248
CHAPTER 10: SIP-MODE OPERATIONS
You can also force the system to transfer the XML file immediately (SIP
Applications > IP Messaging > Send Update Now).
Then, at defined intervals (the default is every 6 hours), the IP Messaging
server collects the XML files from one or more systems, combines the
information into a single XML file, and creates the new mailboxes.
Make sure that all extensions are unique. If you have more than one NBX
system, you cannot use the same extensions on the different systems.
Force Mailbox
Creation
If you do not want to wait for the next defined interval in which the IP
Messaging Module processes the information it received from the system,
you can load the system’s XML file into the IP Messaging Module
immediately.
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > IP Messaging.
3 Click the Send Update Now button to force the system to provide an
immediate update to the IP Messaging Module server.
4 Log in as app on the server on which the IP Messaging Module software
resides.
5 Enter these commands:
cd /user/app/gen
sh blk_nbx_import.sh
The IP Messaging Module software immediately uses the information
from the system’s XML file to create mailboxes on the IP Messaging
Module server.
Telephone users can use the 3Com IP Messaging Module to change their
voice mail password. The passwords for logging into the NBX NetSet
utility and the IP Messaging voice mail system are never synchronized.
Therefore, the telephone user has two separate passwords.
Configure Auto
Attendants
You must configure the system to use the Auto Attendant services of the
IP Messaging Module. This section describes how to configure IP
Messaging on the system. For instructions about how to configure the IP
Messaging server to operate with the system, see the IP Messaging
Enabling and Configuring SIP Mode
249
Module Installation Guide, which is available through the NBX NetSet
utility (click Downloads > Documentation).
The IP Messaging Module includes a default Auto Attendant and you can
create your own customized Auto Attendants. You must configure the
Auto Attendant settings on the IP Messaging Module before those
services are available to the system. For information about how to create
Auto Attendants, see the IP Messaging Operations and System
Administration Guide.
To specify an IP Messaging Auto Attendant on the system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > IP Messaging, and then click the Auto Attendant
tab.
3 To add a new Auto Attendant, click Add. To modify an existing Auto
Attendant, click the Auto Attendant’s mailbox number (or port number).
4 Specify an Auto Attendant Mailbox and a description of that mailbox.
Before this Auto Attendant can be operational, you must use the IP
Messaging Application utility (AppMon) to configure the Auto Attendant
on the IP Messaging Module. When you assign a mailbox to the Auto
Attendant, you must specify the same mailbox number you entered in the
NBX NetSet utility.
5 Click OK or Apply to save your changes.
Configure Music on
Hold
The external IP Messaging Module provides Music on Hold (MOH) and
Music on Transfer (MOT) services for a SIP mode system. However, there is
a practical limit in enabling these features because the IP Messaging
application has a limit of 150 ports for sessions at any one time.
The NBX system’s WAV file importing capabilities are solely an
accommodation to you and shall not constitute a grant or waiver (or
other limitation or implication) of any rights of the copyright owners in
any audio content, sound recording or underlying musical or literary
composition. Therefore, please be mindful that you are obligated to
comply with all applicable copyright and other intellectual property laws
in both uploading WAV files to the NBX system and your subsequent use
of such WAV files.
250
CHAPTER 10: SIP-MODE OPERATIONS
You must configure the MOH/MOT settings on the IP Messaging Module
before those services are available to the system. For information about
how to create MOH/MOT service on the IP Messaging Module, see the IP
Messaging Operations and System Administration Guide.
To configure mailbox information for the Music on Hold (MOH) and
Music on Transfer (MOT) services on the system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > IP Messaging, and then click the Music On Hold
tab.
3 Select the MOH and MOT options and provide the mailbox number that
the IP Messaging Module uses to provide music service. You must provide
a mailbox number if either the Music on Hold or Music on Transfer check
boxes are enabled.
4 Click OK or Apply to save your changes.
Before the services can be operational, you must use the IP Messaging
Application utility (AppMon) to configure the services on the IP
Messaging Module. When you assign a mailbox to the services, you must
specify the same mailbox number you entered in the NBX NetSet utility.
Configure ACD
Delayed
Announcements
If your system is operating in SIP mode, you must use an external
messaging application to provide Automatic Call Distribution (ACD)
announcements. A system running in SIP mode supports ACD
Open/Closed announcements. It does not support estimated wait-time
announcements or In-Queue Digit Processing. For more information, see
“Call Distribution Groups” on page 135.
SIP Telephone Restrictions and ACD
These restrictions apply to SIP-only devices and their interaction with
ACD:
■
A SIP-only phone cannot be a member of an ACD group.
■
A SIP-only phone cannot be a member of a Hunt group or a Calling
group.
Enabling and Configuring SIP Mode
251
ACD Features Not Available in SIP
These ACD features are not available on a SIP mode system:
■
In Queue Digit processing
■
Queue Exit announcement
■
Estimated Wait time Announcement
■
Business and custom hours
■
Shifts
■
Closed announcement
Incoming ACD Calls From a SIP Gateway
Calls coming in to an ACD group from a SIP gateway exhibit the same
behavior as incoming calls from any other source. However, do not set
the call coverage for that ACD to a 3Com phone. An ACD group’s call
coverage can be:
■
Another ACD group
■
Hunt group
■
Sip phone
ACD Announcement on a SIP-Mode System
You must configure ACD Announcements on a SIP-mode system on the
IP Messaging Module. The following is a brief explanation of the Delayed
Announcement functionality with 3Com IP Messaging Module:
1 Configure the 3Com IP Messaging Module for the various
announcements.
Each announcement is assigned to a mailbox on the 3Com IP Messaging
Module. This is a read-only mailbox. When the mailbox receives a call, the
mailbox plays the announcement assigned to it. Announcements can be
imported, or they can be recorded to the 3Com IP Messaging Module.
The telephone user can use the IP Messaging facility to record
announcements. The system administrator is responsible for configuring
the mailboxes on IP Messaging with appropriate announcements.
252
CHAPTER 10: SIP-MODE OPERATIONS
For example, assume that IP Messaging is configured as follows:
Table 51 Example ACD Mailboxes
Mailbox Name
File Name
Mailbox1
welcome.wav
Mailbox 2
sales.wav
Mailbox3
support.wav
Mailbox4
ProductInfo.wav
Mailbox5
Phones.wav
To ensure that all the announcements play consecutively, configure the
announcements on the IP Messaging server so that the No Cut Through,
Play Prompt Once Only, and End Call After Prompt options are enabled.
From the Application utility (AppMon), use the Auto Attendant
Configuration screen and the Advanced Mode Options drop-down list to
enable these options. See the IP Messaging Module Installation Guide for
more information about how to configure announcements.
2 Set up the Delayed Announcements for the ACD groups.
The NBX NetSet utility lets you map Mailbox numbers (present on IP
Messaging) to an Announcement Description (click SIP Applications >
Announcements).
Keeping with this example, assume that you create an ACD Group that
plays announcements regarding telephone information. Therefore, ACD
is configured to use the announcements on Mailboxes 1, 4, and 5. To
accomplish this you must configure the announcements as follows:
Mailbox
Announcement Description
Mailbox1
Welcome to 3Com
Mailbox4
Product Information
Mailbox5
Phones Information
3 Go to the Announcements configuration page for the ACD Group to do
the announcement assignment.
The interface is similar to the voice mail page except that the Filename
field is the Announcement Description field, and this field provides the list
of the configured announcements. Therefore, you simply need to provide
the timeout parameters and select the Announcement Description from
the drop-down list, as follows:
Enabling and Configuring SIP Mode
Announcement Description
253
Timeout
Welcome to 3COM
45sec
Product Information
50sec
Phones Information
60sec
4 If a caller dials the ACD group extension and is placed in the ACD queue,
the system plays the Delayed Announcements as they were configured
using the 3Com IP Messaging Module.
For each different Announcement the systems makes a call to the
appropriate 3Com IP Messaging Module Mailbox (a URL, such as
Mailbox@ipms.com). In the above case, new requests are sent to the IP
Messaging Service after each timeout. Therefore, the IP Messaging
Service receives 3 requests:
■
Mailbox1@ipms.com
■
Mailbox4@ipms.com
■
Mailbox5@ipms.com
Adding and Modifying Announcement Mailboxes
To add or modify an announcement mailbox on the system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > IP Messaging, and then click the Announcements
tab.
3 To add a new auto announcement, click Add. To modify an existing
announcement, click the mailbox number (port number) of the
announcement you want to modify.
4 Click OK or Apply to save your changes.
Before the services can be operational, you must use the IP Messaging
Application utility (AppMon) to configure the services on the IP
Messaging Module. When you assign a mailbox to the services, you must
specify the same mailbox number you entered in the NBX NetSet utility.
Add Trusted SIP
Interfaces
Trusted SIP Interfaces may be SIP gateways, other NBX systems, 3Com
VCX telephone systems, Call Processors or other trusted interfaces. Each
interface you add and how you configure it affects your device licensing.
Each audio path trusted end point requires one system device license. See
“Licensing and Resource Limits” on page 241 for more information.
254
CHAPTER 10: SIP-MODE OPERATIONS
You do not add telephones as trusted interfaces. For information about
how to add 3Com telephones and generic SIP telephones to the NBX SIP
mode system, see “Adding Telephone Users and Devices” on page 258.
To add or modify a trusted SIP interface:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > Trusted SIP Interfaces.
3 Click Add to add a new trusted interface or click an extension from the
list to modify that trusted interface.
4 See the online Help for detailed information about each field.
Add an Optional IP
Conferencing Module
SIP mode operations support only 3-party conferences. You can add an
external conferencing server, such as the 3Com IP Conferencing Module,
to expand your system’s conference capabilities. The 3Com IP
Conferencing Module supports up to 25 telephones in a conference.
The IP Conferencing Module supports two types of Meet-Me
conferences:
■
Public — Public conferences are dial-in conferences in which a caller
can dial a conference extension and connect directly to the
conference.
■
Restricted — Restricted conferences are secure conferences. Callers
must authenticate themselves before the system allows them to join a
conference. The system connects a caller to the IP Conferencing
Module Attendant, which requires the caller to provide a Conference
ID and a password.
Use the NBX NetSet utility to configure IP Conference Server and
Conference Attendant settings:
■
3Com Conferencing servers use different UDP ports for Restricted and
Public conferences. Therefore, you must configure these ports
separately in the NBX NetSet utility.
■
You must configure a dedicated conference extension to enable callers
to connect to the IP Conferencing Module Attendant.
■
Each conference you add is a trusted SIP interface, which the system
includes in the Trusted SIP Interfaces list.
Enabling and Configuring SIP Mode
■
255
You must edit your dial plan to complete the 3Com IP Conferencing
Module configuration.
To configure IP Conference Server:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > 3Com IP Conferencing Module.
3 Type the extension that the system uses for IP Conferencing. This
extension must be an unused extension on the system in the range of
external extensions, which is defined as 6000-7999 by default in a 4-digit
dial plan. You must use a different extension from the one you use to
configure the Conference Attendant settings.
4 Type a description for the IP Conferencing Module.
5 Type the IP address for the IP Conferencing Module.
6 Type a port number. A SIP endpoint is identified by the IP and port
combination.
Port 5060 is set as the default during installation and typically does not
need to be changed.
7 Type the maximum number of simultaneous sessions. Each session
requires one system device license. See “Licensing and Resource Limits”
on page 241 for more information.
8 Click OK or Apply to save your changes.
When you click Apply, the system adds a trusted endpoint. Click SIP
Applications > Trusted SIP Interfaces to verify.
9 Configure the dial plan.
You must add an extension list to the dial plan to support routing of
extensions to the conference server or edit the extension list, if one has
already been created. For more information see “Dial Plan and 3Com IP
Conferencing Module Configuration” on page 257.
To configure the settings of the Conference Attendant for restricted
conferences:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click SIP Applications > 3Com IP Conferencing Module, and then click the
Conference Attendant Settings tab.
256
CHAPTER 10: SIP-MODE OPERATIONS
3 Type the extension that the system uses for IP Conferencing. This
extension must be an unused extension on the system in the range of
external extensions, which is defined as 6000-7999 by default in a 4-digit
dial plan. You must use a different extension from the one you used to
configure the IP Conference Server settings.
4 Type a description for the IP Conferencing Module.
5 Type the IP address for the IP Conferencing Module.
6 Type a port number. A SIP endpoint is identified by the IP and port
combination.
Port 5092 is the port number defined in the IP Conferencing server for
running the Conference Attendant.
7 Type the maximum number of simultaneous sessions. Each session
requires one system device license. See “Licensing and Resource Limits”
on page 241 for more information.
8 Click OK or Apply to save your changes.
When you click Apply, the system adds a trusted endpoint. Click SIP
Applications > Trusted SIP Interfaces to verify.
9 Configure the dial plan. You must add an extension list to the dial plan to
support routing of extensions to the conference server or edit the
extension list if one has already been created. For more information see
“Dial Plan and 3Com IP Conferencing Module Configuration” on
page 257.
Enabling and Configuring SIP Mode
257
Dial Plan and 3Com IP Conferencing Module Configuration
You must configure the dial plan to complete the 3Com IP Conferencing
Module configuration. The following procedure describes the process. For
complete dial plan information, see “Dial Plan” on page 261.
1 Add an extension list to the dial plan to support routing of extensions to
the 3Com IP Conferencing Module.
For example, you can define the 3Com IP Conferencing Module
extension list as follows:
/
/
DestinationRoute Create
Route
----900
/
Route
/
----DestinationRouteEntry Create
9
Description
----------Conference
Entry
----1
DestinationExtension
-------------------*0900
/ Extension List *0900 holds the internal extension of 3Com IP Conferencing Module
2 Create a route entry in the dial plan for the dialed-in digits the telephone
user of the 3Com IP Conferencing Module enters.
For example, using the extension list created in Step 1, the entry below
shows a dial-in that begins with 900.
/
/
Table Entry Create
ID
--1
Entry
----6
Digits
-----900
Min
--3
Max
--3
Class
----internal
Prio
---0
Route
----900
Therefore, if the caller dials 900, the system receives the extension of the
3Com IP Conferencing Module and the port number for the private
conference from the dial plan. The system can route the call to the 3Com
IP Conferencing Module.
3Com Public IP Conferencing Module Configuration
You must configure the dial plan to complete the 3Com Public IP
Conferencing Module configuration. The dial plan uses the private
conference dial plan if it is configured; otherwise, you need to configure
the dial plan for Public conference.
258
CHAPTER 10: SIP-MODE OPERATIONS
The only change required is in the dial plan prefix entry table because in a
Public conference, you need to define a range of extensions rather than a
single extension.
For example, using the above configuration and taking the case that the
extensions range from 700-799, the table entry can be as follows:
/
/
Table Entry Create
ID
--1
Entry
----7
Digits
-----7
Min
--3
Max
--3
Class
----internal
Prio
---0
Route
----900
If the caller dials 700, the system receives the extension of 3Com IP
Conferencing Module and the port number for the Public conference
from the dial plan. The system can route the call to the 3Com IP
Conferencing Module.
Adding Telephone
Users and Devices
Adding a Generic SIP
Telephone
This section explains how to add a generic SIP telephone or a 3Com 3108
Wireless Telephone to a SIP-mode system. For information about how to
add other types of 3Com telephones, see “Telephone Configuration”on
page 93, which describes how to add devices manually or by using the
Auto Discovery feature. The procedures apply to both SIP mode and
3Com call control mode systems. However, because the 3Com 3108
Wireless Telephone is a SIP device, you cannot use Auto Discovery to add
it to the system. See“Adding a 3Com 3108 Wireless Telephone” on
page 260 for information about how to add a 3108 to a SIP mode
system.
To add a generic SIP telephone to the SIP mode system,
■
Add a new telephone user and extension to the system and then
configure the telephone with that username, the default password
(1234) and the extension. If you are not using a DHCP server, you may
need to configure IP connection information.
■
Configure the SIP telephone with system data, such as the system IP
address and UDP port authentication information, and the extension
you created in the NBX NetSet utility.
The SIP telephone has configuration interface that lets you configure
it. Most generic SIP telephones include an embedded web server that
enables you to connect to the phone directly and configure
authentication and feature settings. After you configure the SIP
Adding Telephone Users and Devices
259
telephone, it uses the authentication information you provided to
register with the system and is a member of the Telephones list (click
Telephone Configuration > Telephones).
To add a generic SIP telephone:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click User Configuration > Users > Add.
3 Specify telephone user information and an unused extension.
When you click OK or Apply, the system creates the telephone user with a
default password of 1234.
4 Connect the telephone to power and the network. Use the telephone
documentation to configure basic network connectivity.
Typically, your phone gets its address from a DHCP server. You can use the
telephone controls to view the phone’s IP address. Scroll through the
phone’s menus until you find a display such as preferences or Network
Info.
5 After you find the telephone’s IP address, open a browser and type it into
the address line.
Most, but not all telephones, include an embedded web server for local
configuration. Be sure to consult the telephone’s documentation if you
cannot access the its configuration interface.
6 After you connect to the telephone’s configuration interface, find and
configure connections settings. For example, on a Sipura telephone, you
click the Admin Login link, and then click the Ext.1 tab to access these
settings:
Proxy
Specify the IP address of the NBX server.
This field may also be known as SIP Proxy.
Display Name
Typically, you specify the extension, although this is not
required.
Password
Specify the default password, 1234. The telephone user
can log in to the NBX NetSet utility and use the extension
as the username and this password, and then change the
password. Do not use the telephone user interface to
change the password because that password change is not
passed to the database.
User ID
Specify the telephone extension.
Use Auth ID
This field must be set to Yes.
260
CHAPTER 10: SIP-MODE OPERATIONS
Auth ID
Use this format: sip:ext@NBX IP address
For example: sip:1022@192.168.123.21
7 When you apply these settings, the telephone typically reboots. It then
registers itself with the system and is a member of the Telephones list
(click Telephone Configuration > Telephones). You will have a dialtone
and be ready to make and receive calls.
Adding a 3Com 3108
Wireless Telephone
A SIP-mode system supports the 3Com 3108 Wireless Telephone, which
uses standard SIP.
The process to add a 3108 Wireless Telephone is similar to adding a
generic SIP telephone with the extra step of establishing connectivity
between the 3108 and your wireless network.
Follow these steps to add a 3108 Wireless Telephone to your SIP mode
system:
1 Log in to the NBX NetSet utility using the administrator login ID and
password.
2 Click User Configuration > Users > Add.
Specify an unused extension number, a first name and last name of the
user, and select Default 3108 Wireless Group as the Telephone Group.
3 Click OK to save the new user profile.
4 Configure connectivity settings on the telephone.
The 3108 Wireless Telephone Guide (click Downloads > Documentation >
Telephone Guides) includes complete instructions about how to configure
the telephone to connect to a wireless network and to the system.
After you configure the settings on the telephone:
■
The telephone sends a registration request that contains the user
extension and password information to the system.
■
The system validates the telephone user.
If the data is valid, the system registers the telephone with the IP
address information in the registration request. After a successful
registration, the new telephone is a member of the Telephones list
(click Telephone Configuration > Telephones).
11
DIAL PLAN
This chapter provides information about understanding, developing, and
managing the dial plan. It describes these topics:
■
Dial Plan Concepts and Overview
■
Dial Plan Tables
■
Dial Plan Pretranslators
■
Managing the Dial Plan Configuration File
■
Outdialing Prefix Settings
■
Managing Extensions
■
Managing Extension Lists
■
Managing Dial Plan Tables
■
Managing Dial Plan Pretranslators
■
Configuring the Dial Plan for the 4ESS Protocol (T1)
■
Dial Plan Configurations and VPIM
■
Configuring the Dial Plan for VPIM
■
Dial Plan Configuration File Commands
■
Sample Solutions Using Dial Plan Configuration File Commands
For more information about these topics and configuration procedures,
see the online Help.
For general information about Virtual Tie Lines (VTLs) and how to
configure them in the dial plan, see “Virtual Connections” on page 333.
Dial Plan Concepts
and Overview
The system’s dial plan defines how the system manages calls. It defines
the set of destinations that the system can reach, how to get to these
262
CHAPTER 11: DIAL PLAN
destinations, and which telephone numbers to dial to reach these
destinations.
The dial plan configuration file is an ASCII text file that implements the
dial plan and specifies pretranslation (digit manipulation). The system is
shipped with several default dial plan configuration files, typically, a
3-digit and a 4-digit file for each supported country.
The dial plan configuration file includes several tables:
■
Internal — Must be table ID 1
■
Incoming — Must be table ID 2
■
Least Cost Routing — Must be table ID 3
■
Routes
■
Pretranslators
You can create additional tables if necessary.
Each dial plan table consists of a series of entries, each of which includes
a sequence of digits and the action the system performs in response to
sending or receiving those digits. For more information about the
Internal, Incoming, and Least Cost Routing dial plan tables, see “Dial Plan
Tables” on page 267.
You can access the dial plan configuration file and manage dial plan
operations, tables, pretranslators, and extension lists through the NBX
NetSet administration utility. However, if your dial plan is larger than
32,000 characters, you cannot use the NBX NetSet utility to edit it. You
must export the dial plan, edit it, and then import it.
Before you configure the dial plan, you must understand these concepts:
■
Call Process Flow on page 263
■
Inbound and Outbound Call Processing on page 263
■
System Database on page 264
■
System Dial Plan on page 264
■
Pretranslation on page 265
■
Routing on page 265
■
System Features Affected by the Dial Plan Configuration on page 266.
Dial Plan Concepts and Overview
Call Process Flow
263
The dial plan configuration file is a key component of inbound and
outbound call processing. The dial plan tables in the configuration file
process incoming calls in this order:
1 Incoming Dial Plan Table
2 Pretranslator Table
The dial plan tables process outgoing calls in this order:
1 Internal Dial Plan Table
2 Least Cost Routing Table
After pretranslation (if performed), the final translation process routes the
call to the destination.
Inbound and
Outbound Call
Processing
The system routes all inbound and outbound calls through the dial plan.
Inbound Call Processing
The system uses the Incoming table to process inbound calls. The system
can also use pretranslators to perform digit manipulations on incoming
calls before it uses the Incoming table.
Each pretranslator operation performs a digit manipulation operation on
the dialed digits. For incoming calls, if the DID/DDI (Direct Inward
Dial/Direct Dial Inward) range matches the internal extensions, the dial
plan requires no pretranslator. However, you can use pretranslators to
map nonmatching dialed numbers on an incoming DID/DDI channel to
internal extensions. See the example in Customer Requirement 1 in
“Sample Solutions Using Dial Plan Configuration File Commands” on
page 324.
Outbound Call Processing
The system processes outbound calls using the Internal dial plan table or
the Least Cost Routing table. You can add entries to the Internal dial plan
table to match the system to your service. See Customer Requirement 2
in “Sample Solutions Using Dial Plan Configuration File Commands” on
page 324.
If you have entries in both the Least Cost and Internal tables for the same
purpose, the behavior of the dial plan can be confusing. 3Com
recommends that you accomplish least cost routing using Internal Table
264
CHAPTER 11: DIAL PLAN
entries. For more information, see TimedRoute Create, TimedRouteEntry
Create, and TimedRouteOperation Create later in this chapter.
System Database
The system database contains a default dial plan that is loaded initially at
the factory and is reloaded if you purge the database.
■
V3000, V3001, V3001R, and V5000 systems — default 4-digit plan
■
NBX 100 — default 3-digit plan
The system stores changes that you make to any system settings in the
database, which includes changes made when you import a modified dial
plan configuration file. When you reboot the system, it loads the
database with any changes that you have made. The system database
includes the settings necessary for system operation.
System Dial Plan
You can import a dial plan configuration file to provide the system with a
set of operating instructions to manage the telephone system.
Alternatively, if you make changes to the currently loaded instructions
through the NBX NetSet utility, you can export the dial plan configuration
file to save it. You can also edit the configuration file off-system with any
ASCII editor to make changes, and then import the modified file. You can
easily reuse a given configuration file on many systems. For more
information, see “Importing and Exporting Dial Plan Configuration Files”
on page 279.
The system is shipped with several default dial plan configuration files,
typically, a 3-digit and a 4-digit file for each country that is supported.
In addition, the samples.txt file contains several examples that illustrate
how you can configure the dial plan configuration file to control how the
system manages incoming and outgoing calls.
Typically, you configure a dial plan completely before you use the system
to control the telephones. Although you can make changes later, major
changes in the dial plan can disrupt the system.
Decide whether you want to use a 3-digit or 4-digit dial plan before you
create the dial plan, autodiscover devices, or manually add telephones or
other devices to the system.
When you import a dial plan, some parameters of the system change
immediately. Other parameters change only when you reboot the system.
Dial Plan Concepts and Overview
265
3Com recommends that you reboot the system each time that you
change the dial plan.
When you reboot the system, you disrupt service to the telephones. Plan
to reboot at a time that does not inconvenience telephone users.
Pretranslation
Pretranslation is the process of translating (or manipulating) dialed digits
before they are passed to the appropriate dial plan table for subsequent
routing. You can set the dial plan to perform pretranslation on incoming
or outgoing calls. For more information, see “Dial Plan Pretranslators” on
page 274.
Routing
Routing specifies how a call reaches a destination. You define the routes
for the system to use in the Routes section of the dial plan configuration
file.
When you define call routing, you can also instruct the system to perform
pretranslations. Both destination routes and timed routes have digit
manipulation operations (append, prepend, replace, stripLead, or
stripTrail).
The system passes dialed digits first through the device’s Least Cost
Routing table (if there is one). If the system finds no entry, it then uses the
Normal dial plan table. If the system does find an entry in the Least Cost
Routing table, it attempts to use that entry and, even if the attempt is
unsuccessful, it does not use the Normal table.
You can route incoming calls to the Auto Attendant port, and you can
instruct the Auto Attendant to route these calls to any internal or external
number.
CAUTION: If you configure the Auto Attendant so that it can access any
external number, you risk the possibility of toll fraud. To reduce the
possibility of toll fraud, include specific external numbers in the outgoing
dial plan table. This precaution prevents outside callers from dialing any
external number except the ones that you define.
There are two types of routes:
■
Destination routes — Specify the extension of a destination device.
They can also perform digit manipulation operations on the dialed
digits that resulted in the selection of this route before those digits are
dialed on the destination device.
266
CHAPTER 11: DIAL PLAN
■
Timed routes — Specify time of day and day of week criteria, which
when met, result in a particular destination route being selected.
CAUTION: If you operate the system in Keyset Mode, routes are not
applicable.
For more information, see “DestinationRoute Create” on page 312,
“TimedRoute Create” page 320, and related entries under “Dial Plan
Configuration File Commands” on page 309.
System Features
Affected by the Dial
Plan Configuration
The dial plan configuration affects several system features:
■
Keyset Mode Operation Using the Dial Plan
■
Hybrid Mode Operation Using the Dial Plan
■
Off-Site Notification
Keyset Mode Operation Using the Dial Plan
If you map any telephone buttons that have status lights to specific
Analog Line Card ports, you enable Keyset mode in the system. Instead
of dialing a single digit (typically 8, 9, or 0) before placing an outside call,
the telephone user presses a button to select an available Analog Line
Card port. The telephone user defines the routing (that is, the selection of
a destination device) by pressing the button to select the Analog Line
Card port; however the system controls the call using the dial plan.
You cannot map a digital line extension in Keyset mode.
The system applies any Class of Service (CoS) restrictions that are
associated with the user's telephone to decide whether to make a call.
The system also uses any pretranslator that a device uses and performs
any required digit manipulation operations before it transmits the digits
on the Analog Line Card or Digital Line Card port.
Hybrid Mode Operation Using the Dial Plan
If you map telephone buttons for some telephones but not others, you
enable Hybrid mode (a mixture of standard and Keyset behaviors). The
system provides a system-wide External Prefix setting, which allows you
to establish a prefix.
Dial Plan Tables
267
Off-Site Notification
The system uses off-site notification to notify telephone users when new
voice mail messages arrive. You can define notification devices and assign
them in the Internal dial plan as well as through the NBX NetSet utility.
Example: When voice mail arrives, the system dials the telephone
number of the telephone user’s pager. Typically, you use a system-wide
prefix to designate the device or devices you want to use for outdialing
purposes, including off-site notification calls.
Example: If the telephone user’s pager number is 800-555-3751, and
the system-wide prefix digit is 9, the system dials 98005553751 to send
a call to the telephone user’s pager.
To instruct the system to dial a single Line Card port or a restricted
number of Line Card ports, create a suitable pool of Line Card ports for
that purpose, and then use an existing set of dial plan table entries (such
as the entries that begin with 8) or create a new set of entries to allow
the dial plan devices to route calls by means of the selected line card
ports.
Example: You set up one 4-port card to manage all off-site notification
calls. You create a set of entries in the Internal dial plan table that each
start with the digit 8. You define a route to the 4-port card for all of these
dial plan entries so that whenever the system acts on one of these entries,
it uses one of the 4 ports on that card to dial out and notify the
telephone user.
To apply different off-site CoS restrictions to different telephone users,
you need multiple dial plan entries. If you are not applying the CoS
restrictions, then a single dial plan entry is sufficient.
Dial Plan Tables
Dial plan tables contain information that controls how the system routes
calls. Each dial plan configuration file consists of at least three dial plan
tables. This section discusses these topics:
■
Dial Plan Command Format
■
Internal Dial Plan Table — Must be table ID 1
■
Incoming Dial Plan Table — Must be table ID 2
■
Least Cost Routing Dial Plan Table — Must be table ID 3
268
CHAPTER 11: DIAL PLAN
■
Adding New Dial Plan Tables
CAUTION: The dial plan must include Tables 1, 2, and 3. Do not delete
them. You may create additional dial plan tables if necessary, but you
must number them 4 or higher.
If the Least Cost Routing table exists, it takes precedence over the Internal
table. If the system cannot find a Least Cost Routing table, it attempts to
find a corresponding entry in the Internal table. If you have entries for the
same purpose in both the Least Cost and Internal tables, the behavior of
the dial plan can be confusing.
See “Dial Plan Command Format” next for a description of dial plan
command syntax and structure. For a complete list and description of dial
plan commands, including command arguments and examples, see “Dial
Plan Configuration File Commands” on page 309.
Dial Plan Command
Format
Each dial plan table contains a sequence of commands. These commands
collectively define how the system manages calls.
Most of the dial plan commands have a similar format, as shown in
Figure 12.
Dial Plan Tables
269
Figure 12 Dial Plan Command Format
Call Classification — Used
with Class of Service
Leading Digits to Collect
Table Entry ID Number
Table Name
Table ID Number
Maximum and Minimum
Characters to Collect
Number of the
route (dial tone
facility) from
Routing Tables
Priority
(Not Used)
Command
Table Create 1 Internal
/
Id Entry
/
TableEntry Create
1
1
TableEntry Create
1
2
TableEntry Create
1
3
Table Create 2 Incoming
/
Id Entry
/
TableEntry Create
2
1
TableEntry Create
2
2
Digits
0
1
2
Digits
0
1
Table Create 3 Least Cost Routing
/
Id Entry Digits
Min Max
1
3
3
1
3
3
Min Max
1
3
1
3
Min Max
Class
Internal
Internal
Internal
Class
Internal
Internal
Class
Prio Route
0
0
0
4
0
0
Prio Route
0
0
4
0
Prio Route
Table 52 describes each field of a dial plan command.
Table 52 Dial Plan Command Fields
Field
Description
Command
Command name. For example, TableEntry Create is the command that makes CoS and call
routing decisions based on the correspondence of dialed digits and table entry digits. See
“Dial Plan Configuration File Commands” on page 309 for a description of each command.
Table ID Number
Table ID number. This is always 1 for the Internal dial plan table, 2 for the Incoming dial plan
table, and 3 for the Least Cost Routing Table.
270
CHAPTER 11: DIAL PLAN
Table 52 Dial Plan Command Fields (continued)
Field
Description
Table Entry ID
Number
Table entry number (a unique number for each entry in the table). Typically, these numbers
are in ascending order in the table, but you can change the order. For example, you may
want to place a new item near other items of the same type (that begin with the same digit)
to help troubleshoot the configuration file.
Digits
One or more digits that begin the dial sequence. Either single or multiple entries can start
with the same digit. The system uses this field with the Min and Max fields to decide when to
make the call routing decision.
Most sample tables have a single entry for digit 0 (zero) to specify how the system manages a
telephone number with zero as the first digit.
If you want the system to manage calls differently, depending on whether they start with 90
or 91, you must have one entry in the table for each of these 2-digit sequences.
Min
Minimum number of digits that the system collects before routing the call.
Max
Maximum number of digits the system collects before routing a call.
Class
Class of Service (CoS). The system uses this information to verify if a caller is allowed to make
this specific type of call. The possible classifications are:
Internal, Local, LongDistance, International, WAN, Toll- Free, Emergency, COCode,
Wireless, Toll, Operator, AlternateLong, TrunkToTrunk, Diagnostics, NotAllowed, Other
Each of these values corresponds to a selection in the NBX NetSet utility.
Priority
Priority number. This field is not used at this time, but must be present and must always be 0
(zero).
Route
Route number. This identifies an entry in the Routes section of the dial plan. Zero is a typical
value for internal calls, and indicates that this call uses no route, in which case, the system
transmits the digits as soon as the caller dials them.
If a new entry in the Internal table does not work, it is possible that the
system is using an entry from the Least Cost table instead. To avoid such
conflicts, you can achieve least cost routing using only the Internal table.
To keep the dial plan as simple as possible, 3Com strongly recommends
that, you use only the Internal table for least cost routing.
For more information about how to use the dial plan configuration file,
see “Managing the Dial Plan Configuration File” on page 277.
Basic Dial Plan Table Examples
These examples describe the basic operation of a dial plan table.
Example: If you use a 4-digit dial plan and the telephone extensions start
with 2, then the table entry with 2 in the Digits column typically has 4 in
the Min column. Before making a determination, the system collects all 4
Dial Plan Tables
271
digits of the extension. If the caller dials fewer than the Min number of
digits, the system times out in 20 seconds.
Example: If Digits = 2, Min = 4, and Max = 4, the system knows that if
the first digit is 2, it must collect no less than 4 and no more than 4 digits
before making the call routing decision.
If the caller dials at least the minimum number of digits and not more
than the maximum number of digits, the system waits 5 seconds and
then routes the call based on the digits the caller dialed. If the caller dials
more than the maximum number of digits, the system attempts to place
the call.
Often, the Max and Min values are identical, because you want the
system to collect a specific number of digits, no more and no less.
Example: For internal extensions, you want the system to collect exactly
3 digits (4 in a 4-digit dial plan) before it makes a determination. Set both
Min and Max to 3 (4 in a 4-digit dial plan).
The two columns may be different if the table entry applies to more than
one situation.
Example: In the United States, the Min value for the 90 entry is 2,
because 90 allows an internal caller to reach a telephone company
operator (9 to get an outside line, and then 0 to get the operator). The
Max value is 64, because the caller can continue to dial after the zero,
enter a number to call, plus a telephone credit card number, and possibly
an identification code number.
If the caller dials only 90 (which satisfies the minimum of two digits) and
stops dialing, the system waits for 5 seconds. If the caller does not dial
other digits, the system connects the caller to the operator.
If the caller dials other digits, the system accepts them up to the limit
of 64. If the caller stops after dialing fewer than 64 digits, the system
again waits 5 seconds before it acts on the dialed sequence of digits.
Example: You can assign a new employee to the Default User Group.
You can then set the permissions for that group so that group members
have permission to make LongDistance calls when the system mode is
Open or Lunch, but not when the system mode is Closed or Other.
272
CHAPTER 11: DIAL PLAN
Example: You can assign the company’s Vice President of Finance to a
group that you name the All Privileges Group. You can set the
permissions for that group so that group members have permission to
make LongDistance calls during all system modes.
Internal Dial
Plan Table
The Internal dial plan table (table ID 1) defines how to manage calls
placed from internal devices, such as 3Com Business or Basic Telephones,
to a destination. A destination can be another internal device, such as a
local telephone, or an external telephone line (Analog Line Card or Digital
Line Card) that connects the system to other facilities.
The Internal dial plan table consists of a series of commands. For an
example of the command format, see “Dial Plan Command Format” on
page 268. Table 52 on page 269 describes each element of the
command. Table 53 describes the predefined routes.
Table 53 Predefined Routes
Route Number
Description
1
Local CO (strip)
2
Local CO (no strip)
3
Voice Application (Auto Attendant on extension 500)
4
Attendant (person)
5
H.323 Gateway
6
Least Cost Route example
Other
User-defined routes
You cannot delete or modify predefined routes. You can only create new
routes.
Each device must have a Normal table. The Least Cost Routing table is
optional. Telephones use the Internal dial plan table (table ID 1) as their
normal outbound table and the Least Cost Routing table (table ID 3) as
their long distance routing table.
Incoming Dial
Plan Table
The Incoming dial plan table (table ID 2) defines how the system routes
calls, which arrive from outside the system, to extensions. Incoming calls
can arrive on analog telephone lines or through Digital Line Card ports.
Dial Plan Tables
273
The incoming dial plan table consists of a series of commands. For an
example and basic understanding of the command format, see “Dial Plan
Command Format” on page 268. For a description of the each element
of a dial plan command, see Table 52 on page 269.
By default, Line Card ports, Digital Line Card ports, and H.323 gateways
use the Incoming dial plan table as their normal dial plan table. An
Incoming dial plan table typically has a more restricted list of dialable
digits than the Internal dial plan table. You usually cannot dial extensions
associated with internal paging or Analog or Digital Line Card ports.
Least Cost Routing
Dial Plan Table
The Least Cost Routing table (table ID 3) defines how to route calls to
minimize the cost of those calls.
Example: You may use two different long distance carriers, one for a
specific geographic region, and one for all other areas of the country. In
the Least Cost Routing table, you can create entries that route calls
differently for those two geographic areas. Each country uses a different
method to accomplish this. In the United States, you can specify the area
codes that apply to a geographic region. In France, you can specify a
carrier by adding prefix digits to the telephone number.
By default, internal telephones specify the Least Cost Routing table as
their least cost table. Typically, devices associated with the Incoming dial
plan table (Line Card ports, Digital Line Card ports, and H.323 gateways)
do not use the Least Cost Routing table.
The Least Cost Routing table is optional. If it does not exist, the system
uses the Internal table routing destinations. If you have entries in both the
Least Cost and Internal tables for the same purpose, the behavior of the
dial plan can be confusing. Therefore, 3Com recommends that you
accomplish least cost routing using Internal Table entries. See TimedRoute
Create, TimedRouteEntry Create, and TimedRouteOperation Create.
Example: If a new entry in the Internal table does not work, it is possible
that the system is using an entry from the Least Cost table instead. To
avoid such conflicts, you can achieve least cost routing using only the
Internal table. To keep the dial plan as simple as possible, 3Com strongly
recommends that, you use only the Internal table for least cost routing.
Adding New
Dial Plan Tables
If you share the system with another company or group and want to
control calls differently at the two sites, you can add a fourth table.
274
CHAPTER 11: DIAL PLAN
Example: Assign one extension range to Company A and a different
range to Company B. The fourth table controls the extension range for
Company B, so that outbound calls from Company B’s extensions use
only their external telephone lines.
You may need a fourth table if a company has two sites but only one
system. To route emergency (911) calls properly, use the fourth table to
define which extensions use each dedicated 911 telephone line.
Example: Telephone users at Site A dial 911 and the system uses the
Internal table (table ID 1) to make the emergency call on one external
telephone line. Users at Site B dial 911 and the system uses table ID 4 to
make the emergency call on a different external telephone line. The
emergency staff know, based on the dialing number, which site has the
emergency.
Enhanced 911, E911, is available in some areas. This service enables
emergency staff to identify the specific location of the emergency. For
example, in a campus of buildings, the emergency staff can identify the
specific building, floor, and location from which the emergency call
originates. The system supports E911 over ISDN. You must define an
outbound call pretranslator to provide the specific extension number
from which the 911 call originates.
Dial Plan
Pretranslators
The system uses pretranslators to modify digit sequences of incoming or
outgoing calls. On incoming calls, pretranslators can map the entire
dialed number (including area code) to an internal extension number.
For example, an external caller dials 978-555-0101 to reach the person
on extension 101. Pretranslators ensure that the proper digits are
mapped to the correct extension number.
For more information, see:
■
Pretranslators for Incoming Calls on page 275
■
Pretranslators for Certain Outgoing Calls on page 276
A typical pretranslator function involves mapping incoming DDI/DID
telephone calls to internal extension numbers.
Example: The DDI/DID telephone numbers range from 508-555-4200
through 508-555-4299. The telephone company sends you the last
Dial Plan Pretranslators
275
4 digits of the total telephone number. Internally, you want to use
extensions 2000 through 2099. You can define a pretranslator to:
■
Remove (stripLead) the first two digits of the incoming 4-digit
sequence.
■
Add (prepend) the digits 20 in front of the remaining 2 digits.
See “Managing Dial Plan Pretranslators” on page 300 for detailed
information about and examples of how to create and manage dial plan
pretranslators.
Pretranslators for
Incoming Calls
For incoming calls, pretranslation reformats the dialed number before it is
passed to the Incoming dial plan table (Table ID 2). See “Incoming Dial
Plan Table” on page 272. For information about how to manage caller ID
and CDR information for incoming VTL calls, see “Creating a
Pretranslator for VTL Calls” on page 301.
Incoming Pretranslator Example 1
For an incoming telephone call, if the telephone company passes you
4-digit numbers from 6100 through 6199, the system can use a
pretranslator to remove the first digit; the remaining 3 digits can then be
used as internal extension numbers in a 3-digit dial plan. Define digit
manipulation operations (append, prepend, replace, stripLead, or
stripTrail) within the PreTranslator section of the dial plan configuration
file to indicate which pretranslations you want to perform.
Incoming Pretranslator Example 2
Assume the telephone company passes 10-digit numbers to the system
for each incoming telephone call (for example, numbers in the range
4567-89-3000 to 4567-89-3500). If the system uses 4-digit extensions in
the range 2000 to 2500, you could pass an incoming 10-digit number
such as 4567-89-3210 to extension 2210.
This strategy requires two pretranslation operations: The first operation
performs a stripLead operation to remove the initial 7 digits, leaving 210.
The second operation prepends the number 2 in front of the remaining 3
digits. The result is 2210, which matches an extension within the
extension range. “Sample Solutions Using Dial Plan Configuration File
Commands” on page 324 shows how to accomplish this pretranslation
using the dial plan configuration file.
276
CHAPTER 11: DIAL PLAN
Each device can specify only one DDI/DID pretranslator and one Calling
Line ID Presentation (CLIP) pretranslator. To create or modify a
pretranslator, you either edit a dial plan configuration file and import it,
or use the NBX NetSet utility and modify an existing dial plan
configuration file.
The system performs operations in ascending order of operation ID.
Operations are both sequential and cumulative.
You can also use pretranslators with virtual tie lines to link multiple
systems. Incoming calls within a defined numeric range arrive at the first
system, are modified through digit manipulation operations, and are then
routed to a tie line connected to a second system.
Each sample dial plan that is shipped with the system includes a default
pretranslator.
Pretranslator Example 3
Assume that the telephone company passes 4-digit numbers to the
system for each incoming telephone call (for example, numbers in the
range 5200 through 5300). If the system uses 3-digit extensions in the
range 200 through 300, you could define a single pretranslation
operation to stripLead (remove) the first digit, for instance, the number 5
from an incoming number such as 5278, and pass the call to extension
278. “Sample Solutions Using Dial Plan Configuration File Commands”
on page 324 shows how to accomplish this pretranslation using the dial
plan configuration file.
Pretranslators for
Certain
Outgoing Calls
On outgoing calls using an ISDN PRI card, pretranslators allow the
external called party to identify the full number of the internal caller,
including the area code. For example, if the person on extension 101
within a company calls an external number, the caller’s entire number is
displayed to the called party when CLIP pretranslators are used.
Pretranslation reformats the outgoing dialed number before it is passed
to the Internal dial plan table (Table ID 1) or possibly the Least Cost
Routing table (Table ID 3). For more information, see “Internal Dial
Plan Table” on page 272 and “Least Cost Routing Dial Plan Table” on
page 273.
Example: If the DDI/DID telephone numbers range from 508-555-4200
through 508-555-4299, internally, you dial extensions from 2000
through 2099 to reach another internal telephone.
Managing the Dial Plan Configuration File
277
When you place a call to an external telephone number, the system can
use these pretranslator steps to create the full 10-digit number:
1 Remove (stripLead) the first two digits (20) from the internal extension
number of the telephone making the call.
2 Add (prepend) the digit sequence 50855542 to the two remaining digits,
creating the full DDI/DID telephone number.
3 Pass the full number to the telephone company.
Example: To transmit CLIP information about outgoing calls, you can
define a pretranslator that transforms internal extensions into full
telephone numbers (the numbers that someone external to the company
uses to dial in). Assume that you use telephone extension numbers from
1000 to 1099 and that only the last two digits match the DDI/DID
numbers that are assigned to the company. You can define a
pretranslator to remove (stripLead) the first two digits from the internal
extension number and add (prepend) the appropriate digit string. This
pretranslator constructs the full telephone number.
Example: If you use two different long-distance carriers at different times
of the day to save costs, you can prepend different digit sequences to the
outgoing dialed number to select which carrier that you want. If you
prepend 1010321 between the time the business opens and 3:00 p.m.,
you select one long-distance carrier. If you prepend 1010220 from
3:00 p.m. until the next time the business opens (including weekends),
you select the other carrier and obtain a lower rate.
Define digit manipulation operations (append, prepend, replace,
stripLead, or stripTrail) in the Routes section of the dial plan configuration
file to indicate which outgoing pretranslations you want to perform. You
can define these commands for both destination routes and timed routes.
For more information about how to configure pretranslators, see
“Managing Dial Plan Pretranslators” on page 300.
Managing
the Dial Plan
Configuration File
This section describes the dial plan configuration file and how to manage
it. From the Operations tab of the Dial Plan window, you can perform
these tasks:
■
Accessing the Dial Plan
■
Creating Dial Plan Configuration Files
■
Importing and Exporting Dial Plan Configuration Files
278
CHAPTER 11: DIAL PLAN
Accessing the
Dial Plan
Creating Dial Plan
Configuration Files
■
Importing a User-Defined Dial Plan
■
Exporting (Saving) a Dial Plan Configuration File
■
Testing a Dial Plan
■
Generating a Dial Plan Report
■
Modifying a Dial Plan Configuration File
To import a dial plan configuration file and modify it, log in to NetSet and
click Dial Plan > Configure, which displays the Operations window. From
this window, you can access customer-defined and default dial plans.
The simplest way to create a new dial plan is to model it after an
existing one.
1 Log on to NetSet using the administrator login ID and password.
2 Click Dial Plan > Configure.
3 Browse for a dial plan, or select one from the pull-down list.
4 Click Open to open the file in your browser.
5 Click Save As and save the dial plan as a new file.
You can now edit the file with an ASCII editor. After you customize the
new dial plan, Import it to the system. see “Importing and Exporting Dial
Plan Configuration Files” on page 279.
3Com recommends that you enter these commands at the top of every
dial plan configuration file:
Table Delete *
DestinationRoute Delete *
TimedRoute Delete *
PreTranslator Delete *
When you subsequently import this dial plan, these commands purge any
traces of the old dial plan and prevent any conflicts that can result from
importing one dial plan on top of an existing one.
You create new entries in the dial plan configuration file by typing in new
commands (see “Dial Plan Configuration File Commands” on page 309)
or by cutting, pasting, and editing existing lines in the file.
Managing the Dial Plan Configuration File
279
When you cut and paste new lines into dial plan tables, change the Entry
number in the pasted line. If two or more lines have the same Entry
number, only the last one takes effect.
Importing and
Exporting Dial Plan
Configuration Files
You import a dial plan configuration file either to implement changes you
made by editing the file, or to reload a previously saved configuration.
From the Operations tab of the Dial Plan window, you can:
■
Import a North American Dial Plan
■
Import an International Dial Plan
When you export the working dial plan, the system constructs a new
configuration file from the values in the database and displays it. The new
file shows the current date and time. You name the file when you save it.
The sample, default files include examples of timed routes and
pretranslators. To preserve the default (sample) dial plan configuration
included with the system, 3Com advises you to choose a unique file name
for new files so that you do not overwrite the sample default files.
Import a North American Dial Plan
The default dial plan scheme is as follows:
■
V3000, V3001, V3001R, and V5000 system —
NorthAmerica-4-digit.txt
■
NBX 100 system — NorthAmerica.txt
The system includes customized dial plans for use in other countries.
Always read the system Release Notes (readme.txt) for the most
up-to-date information about dial plans.
To import a default dial plan configuration file:
1 Click Dial Plan > Configure.
2 Click the Default File radio button and from the Default File drop-down
list, select the default file that you want to use.
3 Click Import.
CAUTION: When you import a dial plan configuration file, the system
immediately implements the dial plan. You are warned that the system
may become inoperative. The system becomes inoperative only if you
280
CHAPTER 11: DIAL PLAN
have modified a dial plan manually and have made syntax or content
errors. Carefully check any changes that you make to the configuration
file before you import it.
4 Click OK. The system imports the new dial plan and produces a report of
any errors.
5 Reboot the system.
Import an International Dial Plan
To change the default North American dial plan to a country-specific dial
plan:
1 Click Dial Plan > Configure.
2 Click the Default File radio button and from the Default File drop-down
list, select the country-specific file that you want to use.
3 Click Import.
CAUTION: When you import a dial plan configuration file, the system
immediately implements the dial plan. You are warned that the system
may become inoperative. The system becomes inoperative only if you
have modified a dial plan manually and have made syntax or content
errors. Carefully check any changes that you make to the configuration
file before you import it.
4 Click OK. The system imports the new dial plan and produces a report of
any errors.
5 Reboot the system.
You may see a warning that “destination extension list is empty.” This
means that a particular type of device is not installed. You may safely
ignore this type of warning.
International Dial Plan Issues
Several international dial plan issues require attention:
Customizing an International Dial Plan. If there is no customized
dial plan for your country, you may need to modify the default dial plan.
See “Modifying a Dial Plan Configuration File” on page 285. If you edit
the default dial plan, you can test the changes by making a simulated call.
See “Testing a Dial Plan” on page 283.
Autodiscovering Internal Telephones. If you autodiscover your
company’s internal telephones, Auto Discovery usually begins at number
Managing the Dial Plan Configuration File
281
100 or 1000. However, for some countries, internal telephones begin at a
higher number to allow you to dial numbers considered of national
importance directly. Auto Discovery allocates telephone extensions
numbers within this range:
■
The default dial plan for the V3000, V3001, V3001R, and V5000
systems allows you to allocate internal telephones to extension
numbers 1000 through 3999.
■
The default dial plan for the NBX 100 allows you to allocate internal
telephones to extension numbers 100 through 449.
For more information about Auto Discovery, see “Auto Discovery” on
page 25
Dialing Outside Lines. To obtain an outside line, dial 9 or 0 as
appropriate for your country.
WARNING: You must first obtain an outside line before you can dial
emergency numbers.
Importing a
User-Defined Dial Plan
To import a customer-defined (user-defined) dial plan configuration file:
1 Click Dial Plan > Configure.
2 In the User-Defined File field, enter the path and name of the
user-defined configuration file, or click Browse to find the file that you
want.
The system has no predefined location for dial plan configuration files.
You can specify any directory or path that you want.
3 Click Import
CAUTION: When you import a dial plan configuration file, the system
immediately implements the dial plan. You are warned that the system
may become inoperative. The system becomes inoperative only if you
have modified a dial plan manually and have made syntax or content
errors. Carefully check any changes that you make to the configuration
file before you import it.
4 Click OK. The system imports the new dial plan and produces a report of
any errors.
5 Reboot the system.
282
CHAPTER 11: DIAL PLAN
Exporting
(Saving) a Dial Plan
Configuration File
When you export (save) the current configuration, the system creates
a new dial plan configuration file from the current database. You save the
new text file using a name that you choose.
This example refers to Internet Explorer. If you use another browser, you
may need to use slightly different procedures.
To export a dial plan configuration file:
1 Click Dial Plan > Configure.
2 Click Export.
The system constructs a new configuration file from the current values in
the database and displays it. Figure 13 shows a partial display. Scroll your
browser window to see your complete dial plan.
Figure 13 Dial Plan Configuration File (partial)
3 Click the File menu and select Save As.
4 From the list box at the top of the Save As window, select the destination
folder.
5 In the File Name field, replace the default file name with a new name.
The sample, default files include examples of timed routes and
pretranslators. To preserve the default (sample) dial plan configuration
included with the system, 3Com advises you to choose a unique file name
for new files so that you do not overwrite the sample default files.
Managing the Dial Plan Configuration File
283
6 Click Save.
Testing a Dial Plan
You can place a simulated call to test the currently loaded dial plan.
Even if your system is completely installed and operational, a test places
a simulated, not an actual call.
Example: If you have an entry in the dial plan for digit sequences that
start with 91, with Min and Max set to 5, and you test the sequence
9123, the dial plan test reports an insufficient number of digits. However,
in actual operation, the system would time out waiting for the fifth digit,
and then attempt to place the call. Assuming that the outside line prefix
is 9 (such as in the United States), this situation would obtain an outside
line (9) and then dial the numbers 123.
You can specify a day of the week and a time by selecting entries from
the Day/Time list boxes. This choice instructs the system to act as if the
day and time you select are the current day and time.
If you define timed routes in the dial plan, you use different day and time
settings to verify if the timed route works properly.
Example: You can define a timed route to select route 35 during open
business hours Monday through Friday, but to select route 36 when
business is closed on those days and on weekends. After you define the
timed route commands and import the modified file, test using days and
times within business hours (to verify that the system selects route 35) and
during closed hours and weekends (to verify that it selects route 36).
You can also use day and time settings to test whether the Class of
Service settings operate as expected.
Example: You can configure the dial plan to allow toll calls from an
extension during open business hours, but to disallow such calls when
the business is closed and on weekends. Test using days and times within
business hours (to confirm that you can make toll calls from that
extension) and during closed hours and weekends (to confirm that the
system prevents such calls).
To create and run a test using the currently loaded dial plan:
1 Click Dial Plan > Configure.
2 Click the Test tab to display the list of extensions from which you can call.
284
CHAPTER 11: DIAL PLAN
3 Click the extension from which you want to dial for the test.
4 In Number to dial, enter the number that you want the system to dial.
5 Select a date and time in the Day/Time pull-down lists.
For some tests, the day and time settings are irrelevant. You can leave the
settings at their default values (Sunday, 00, and 00).
6 Click Test. The test runs and the results appear in the dialog box.
Generating a
Dial Plan Report
You can create a report that contains all dial plan settings, tables, routes,
and pretranslators. Also, the report:
■
Performs a consistency check to ensure that all dial plan table entries
point to valid routes which, in turn, point to valid extensions.
■
Identifies how many devices are using each dial plan table and each
pretranslator.
To generate a dial plan report:
1 Click Dial Plan > Configure.
2 Click Reports, which displays the dial plan report in the browser window.
Errors can prevent calls from being successfully routed. Warnings are
conditions that you can easily correct to route the call successfully.
To record test results and send them to someone, select the text in the
results pane and use the browser’s copy function (typically found in the
Edit menu) to copy the test results to another application window, such
as an editor or e-mail.
3 Click Close.
The person who validates the dial plan test is responsible for verifying
that the test call used the correct dial plan table and dial plan table entry.
Be aware of these common dial plan problems:
■
Dial plan table entries that point to nonexistent routes
■
Timed route entries that point to nonexistent destination routes
■
Destination route entries that point to nonexistent extensions or
empty extension lists
■
Timed route entries that overlap
■
Devices that do not specify a normal table
Managing the Dial Plan Configuration File
285
■
Devices that point to nonexistent Normal tables, Least Cost Routing
tables, or pretranslators
■
Pretranslator entries that have no operations
If a telephone has no table assigned, that telephone does not have
permission to dial. The system reports this error. If a device has only a
Normal table, the system reports no error.
If a device has only a Least Cost table, the system reports an error. The
telephone is still usable and has permissions defined in whatever table
has been chosen as Least Cost. If a device has both a Normal and Least
Cost table, the system reports no error (the usual condition).
When the system detects an error in any line of an imported dial plan
configuration file, it ignores that line and continues to process all
remaining lines in the file. This precaution minimizes the impact of errors
on the dial plan.
Modifying a Dial Plan
Configuration File
You can modify the currently loaded dial plan configuration file.
CAUTION: Modifications must be syntactically correct. Each time that the
system imports a dial plan configuration file, it verifies the file for errors
and displays the results. To avoid typing mistakes, 3Com suggests that
you start with an existing dial plan (for example, one of the default plans
that are shipped with the system or a plan from another system), modify
it, and save it as a renamed file.
To modify a dial plan configuration file:
1 Click Dial Plan > Configure.
2 Click the Modify tab. Scroll up and down the browser window to see the
complete dial plan.
3 Edit the dial plan configuration file.
A single line of space is required between each dial plan entry. You can
type a complete dial plan entry anywhere in the file.
4 Click Apply and then click OK to confirm.
The system imports the modified dial plan and displays the results of the
error and consistency checks.
5 To correct any errors, edit the file and click Apply. You may be required to
make changes based on warning messages.
286
CHAPTER 11: DIAL PLAN
Outdialing Prefix
Settings
A telephone user can use the telephone display panel to look up a call in
the call logs (Missed Calls, Answered Calls, and Dialed Calls), select a
telephone number from any of the logs, and redial it.
To redial a number from the Missed Calls or Answered Calls list, the
system must know the appropriate dial prefix to prepend to the digits in
the telephone number.
For information about and examples of how to configure outdialing
prefixes, see the online Help.
Managing
Extensions
Extension Settings
Overview
This section describes how to add, change, and manage extensions:
■
Extension Settings Overview
■
Changing Extension Length and Ranges
■
How Auto Discovery Assigns Extensions
■
Modifying Extensions
■
Converting Extensions
The system establishes connections between extension numbers. The
concept of an extension applies to more than just telephones. Extensions
are also assigned to applications such as Call Park zones, Auto
Attendants, hunt groups, Line Card ports, voice mail ports, and virtual
devices such as the pcXset™ PC soft telephone Client.
The extension length (either 3 or 4 digits), which applies to all extensions
on a system, indicates that all extensions contain that number of digits.
You cannot mix 3-digit and 4-digit extensions within the same system.
Systems support 3-digit and 4-digit dial plans, although there are some
differences in the extension ranges as noted in these tables. By default,
NBX 100 systems use a 3-digit dial plan, and V3000, V3001, V3001R,
and V5000 systems use a 4-digit dial plan.
Table 54 lists typical extension ranges by type. Table 56 describes these
ranges in more detail.
Managing Extensions
287
Table 54 Typical Extension Ranges by Type
Extension Type
4-digit
Telephones
1000–3999
Auto Attendant
500, 501, plus 5500–5599
Hunt Group
4000–4099
External Extensions
(includes line card
ports and Call Park)
6000–7999
(external Auto Discovery
starts at 7250)
Call Park (must fall
within External
Extension range)
6000–6099
Note 1: The V3000, V3001, V3001R, and the V5000 systems are shipped with a
factory default 4-digit dial plan. If you import any 3-digit plan, you must manually
specify any 3-digit extension ranges that are not set by the imported plan. You must
also manually change any device extensions so that they fall within the appropriate
range.
Note 2: The NBX 100 system is shipped with a factory default 3-digit dial plan. If you
import any 4-digit plan, you must manually specify any 4-digit extension ranges that
are not set by the imported plan. You must also manually change any device
extensions so that they fall within the appropriate range.
Note 3: TAPI Route Point extensions occur in the same range as telephones. TAPI
Route Point extensions do not appear in telephone lists within the NBX NetSet utility.
For more information about TAPI Route Points, see “TAPI Route Points” on
page 356.
Note 4: An extension cannot begin with a zero.
Table 55 Typical Extension Ranges for 3-digit and 4-digit Dial Plans
Extension Type
3-digit
4-digit
Telephones
100–449
1000–3999
Auto Attendant
500–599
500, 501, plus 5500–5599
Hunt Group
450–499
4000–4099
External Extensions
(includes line card
ports and Call Park)
600–799
(external Auto Discovery
starts at 750)
6000–7999
(external Auto Discovery
starts at 7250)
Call Park (must fall
within External
Extension range)
601–609
6000–6099
288
CHAPTER 11: DIAL PLAN
Table 55 Typical Extension Ranges for 3-digit and 4-digit Dial Plans (continued)
Extension Type
3-digit
4-digit
Note 1: The V3000, V3001, V3001R, and V5000 systems are shipped with a factory
default 4-digit dial plan. If you import any 3-digit plan, you must manually specify
any 3-digit extension ranges that are not set by the imported plan. You must also
manually change any device extensions so that they fall within the appropriate
range.
Note 2: The NBX 100 system is shipped with a factory default 3-digit dial plan. If you
import any 4-digit plan, you must manually specify any 4-digit extension ranges that
are not set by the imported plan. You must also manually change any device
extensions so that they fall within the appropriate range.
Note 3: TAPI Route Point extensions occur in the same range as telephones. TAPI
Route Point extensions do not appear in telephone lists within the NBX NetSet utility.
For more information about TAPI Route Points, see “TAPI Route Points” on
page 356.
Note 4: An extension cannot begin with a zero.
Table 56 provides a more detailed explanation of extension types,
including default extension ranges and values for 3-digit and 4-digit dial
plans.
Table 56 Dial Plan Extension Settings
Field
Purpose (See Notes 1 – 3)
Telephone
Extensions
The range of extensions for telephones.
■
4-digit dial plan: 1000–3999
■
3-digit dial plan: 100–449
TAPI route point extensions are included in the telephone
extensions range.
Length — This drop-down list specifies the number of digits for
telephone extensions.
Note: An extension cannot begin with a zero.
Auto Attendant
Extensions
The range of extensions for Auto Attendants.
Default:
■
4-digit dial plan: 5500–5599
■
3-digit dial plan: 500–599
For both 3-digit and 4-digit dial plans:
■
Extension 500 is reserved as the default Auto Attendant.
■
Extension 501 is reserved as the voice mail Auto Attendant.
Managing Extensions
289
Table 56 Dial Plan Extension Settings (continued)
Field
Purpose (See Notes 1 – 3)
Default Auto
Attendant
Extensions
Default extension that the system assigns to the default Auto
Attendant. The Auto Discovery process assigns this extension.
The system must direct each call coming in on an external line to
an extension. During the Auto Discovery of external lines
(analog lines and Digital Line Card channels), the system assigns
the default extension (500) as the Auto Attendant extension.
After you import the dial plan configuration file and complete
the Auto Discovery process, you can manually configure the
extension for each analog line and each Digital Line Card
channel.
For both 3-digit and 4-digit dial plans:
Hunt Group
Extensions
External
Extensions
■
Extension 500 is reserved as the default Auto Attendant.
■
Extension 501 is reserved as the voice mail Auto Attendant.
The range of extensions for hunt groups.
■
4-digit dial plan: 4000–4099
■
3-digit dial plan: 450–499
The range of extensions that are connected to external devices,
such as Analog Line Card ports, Digital Line Card ports (BRI-S/T,
T1, E1, ISDN PRI), Call Park, and Paging extensions.
Default:
Call Park
Extensions Range
Start External
Discovery At
■
4-digit dial plan: 6000–7999
■
3-digit dial plan: 600–799
The range of extensions for Call Park. This feature allows the
telephone user to park a telephone call temporarily and then
pick it up at a different telephone. Call Park extensions must be
a subset of external extensions.
■
4-digit dial plan: 6000–7999
■
3-digit dial plan: 600–799
The system assigns extensions to external devices it
autodiscovers, starting with this number and incrementing
upward. If the system reaches the highest extension, it starts
searching from the beginning of the external range and selects
the first unused one.
Typically, systems do not use all of the available external
extensions from 600–799 in a 3-digit dial plan or from
6000–7999 in a 4-digit dial plan.
Default:
■
4-digit dial plan: 7250
■
3-digit dial plan: 750
290
CHAPTER 11: DIAL PLAN
Table 56 Dial Plan Extension Settings (continued)
Field
Purpose (See Notes 1 – 3)
External Keyset
Prefix
In Keyset mode, when a button on a 3Com Business Telephone
directly accesses an outside line, the system must check Class of
Service. The system prepends the External Keyset Prefix value
(typically 8, 9, or 0) when it makes a call in Keyset mode.
Default Auto
Extension
Default extension that the system assigns to the default Auto
Attendant. The Auto Discovery process assigns this extension.
Default menu Auto Attendant: 500
Voice mail Auto Attendant: 501
Note 1: The V3000, V3001, V3001R, and V5000 systems are shipped with a factory
default 4-digit dial plan. If you import any 3-digit plan, you must manually specify
any 3-digit extension ranges that are not set by the imported plan. You must also
manually change any device extensions so that they fall within the appropriate
range.
Note 2: The NBX 100 system is shipped with a factory default 3-digit dial plan. If
you import any 4-digit plan, you must manually specify any 4-digit extension ranges
that are not set by the imported plan. You must also manually change any device
extensions so that they fall within the appropriate range.
Some countries reserve numbers that begin with 11 for numbers of
national importance. To accommodate this requirement, you can begin
the telephone extension range at 120.
Changing Extension
Length and Ranges
You can view and change extension settings, such as extension length
and extension ranges.
If you change from a 3-digit to a 4-digit plan, import the 4-digit dial plan
configuration file before you configure or autodiscover any devices.
To view and change extension settings:
1 Click Dial Plan > Configure.
2 Click the Settings tab.
3 Make the necessary changes to the extension settings. Table 56 describes
each field.
4 Click Apply.
Planning Extension Ranges
Plan extension ranges to accommodate your present and future needs.
An extension cannot begin with a zero.
Managing Extensions
291
Example: If you initially have 60 telephones and expect to add no more
than 100 additional telephones in the future, choose 100–299 as the
telephone extension range (1000–1199 in a 4-digit system). This
arrangement provides 200 extension numbers to manage the planned
160 telephones plus 40 extra extensions to manage unexpected
additions.
Once you set the telephone extension range, you can extend it later,
provided that the new range does not overlap any other number range.
Example: For a 4-digit dial plan, you can set the initial telephone
extension range to 1000–1099. This arrangement allows for up to 100
telephone extensions. Later, you can extend the range up to 3999 to
allow for 400 telephone extensions. By default, the Hunt Group range
starts at 4000, 450 for a 3-digit dial plan, so you cannot assign telephone
extensions in either of those ranges.
How Auto Discovery
Assigns Extensions
The Auto Discovery process assigns new extensions to telephones and
other devices. For example, if you install a T1 or E1 Digital Line Card, you
can use Auto Discovery to assign extension numbers to each port on the
card. The Auto Discovery process initially assigns a default name (new
user) to each new telephone, and assigns the next available extension
number. Later, you can replace (new user) with the appropriate telephone
user’s name.
It is possible to bypass the Auto Discovery process and to add a new
telephone and assign an extension manually. However, 3Com strongly
recommends that you take advantage of the Auto Discovery process. For
instructions about how to use Auto Discovery, see “Adding a New
Telephone” on page 93.
You can define a telephone user in the system database and not assign a
telephone to that user. When you define a telephone user with only a
telephone extension, you create a phantom mailbox. The system
associates an extension with this phantom mailbox so that the telephone
user has voice mail capability. To access voice mail from any telephone,
the telephone user calls either extension 500 (the default Auto Attendant
extension), or 501 (the default Auto Attendant voice mail extension.)
Telephones and Line Card ports reserve most of the extensions within the
system. However, there are other extensions within the system. Table 54
lists the default extension ranges for 3-digit and 4-digit dial plans.
292
CHAPTER 11: DIAL PLAN
Modifying Extensions
You can modify the extension number of any device in the system.
Normally, you make changes only after you have changed the extension
ranges for the system, to align the extensions with the new ranges.
CAUTION: Be careful when you change extensions. The system does not
validate changes that you make, and there is no Undo or Cancel function.
A mistake can compromise the operation of the system.
To modify extensions:
1 Click Dial Plan > Configure.
2 Click the Modify Extensions tab.
3 Select the extension, or extensions, that you want to modify. To select all
extensions, enable the Select check box.
4 Select an operation from the drop-down list and make the appropriate
entries in the field, which display after the member list:
■
Change Extension — Modifies the first selected extension with the
number you type in the field next to the drop-down list. Change
Extension applies to only one extension at a time. If you select multiple
extensions, the system changes only the first extension that you
selected.
■
Prepend — Prepends digits in front of all selected extensions.
■
Append — Appends digits to the end of all selected extensions.
■
Strip Leading Digits — Strips (removes) the specified number of
digits from the beginning of all selected extensions. For example, if
you type the number 2 in the field, the system strips (removes) two
digits from the beginning of the extension.
■
Strip Trailing Digits — Strips (removes) the specified number of
digits from the end of all selected extensions.Click Apply to make the
changes, or click Reset to restore the settings to their original status.
If the requested change creates a duplicate extension or an extension of
zero length, the system discards the change. For example, if you select
extensions 1000 through 1009 and select Strip Trailing Digits, the system
makes no change, because the result is a series of identical numbers (all
100).
Converting
Extensions
The Convert Extensions feature enables you to use the NBX NetSet utility
to change these extension types from 3-digits to 4-digits or from 4-digits
to 3-digits quickly:
Managing Extensions
■
Virtual Tie Line (VTL) extensions
■
Voice mail port extensions
■
Call Park extensions
■
Paging extensions
293
The Convert Extensions feature helps you in the larger task of converting
a dial plan between 3- and 4-digits. To perform a complete a dial plan
conversion, you must also manually convert any existing extensions for
these extension types:
■
External extensions (Analog Line Card ports, Analog Terminal Card
ports, and Digital Line Card channels extensions)
■
Internal extensions, which includes TAPI Route Point extensions
■
H323 Gateway extensions
■
Hunt Group and Automatic Call Distribution Group extensions
To convert a dial plan between 3- and 4-digits, follow these steps:
1 If the conversion is part of a hardware upgrade:
a Install the new hardware.
b Install new licenses on the new system. You cannot move licenses
from the old system to the new system. Licenses keys are tied to a
system (hardware) ID number.
2 If you are upgrading your hardware, migrate your data from the old
system to the new system. For details about data migration, see
“Migrating Data” on page 86.
3 Click Dial Plan > Configure.
4 Verify that the system is set up for the type of dial plan you want. For
example, if you are converting an existing system from a 3-digit to a
4-digit dial plan, import the 4-digit dial plan. The 4-digit dial plan is the
default dial plan for V3000, V3001, V3001R, and V5000 systems.
5 Click Convert Extensions.
The system automatically converts existing extensions of these extensions
to conform with the dial plan (3-digit or 4-digit) that is currently installed
on the system:
■
Call Park extensions
■
Voice mail port extensions
294
CHAPTER 11: DIAL PLAN
■
Virtual Tie Lines
■
Paging extensions
6 Manually specify new values for any of these existing extensions:
■
Telephone Extensions
■
Auto Attendant Extensions
■
Hunt Group and ACD Group Extensions
■
External Extensions (digital channel and analog port extensions)
To modify an existing extension, click Dial Plan > Configure, and then
click the Modify Extensions tab. Edit the list of extensions so that each
extension falls into the range for its extension type:
Extension Type
3-digit Dial Plan Defaults
4-digit Dial Plan Defaults
Internal Extensions
100-449
1000-3999
Hunt Group and ACD 450-499
Group Extensions
4000-4099
Auto Attendant
Extensions
5500-5599
500-599
External (digital and
600-799
6000-7999
analog line card port)
The external extension range includes Call park extensions,
extensions
which are converted when you use the Convert Extensions
feature described previously in step 4.
7 Edit your dial plan to configure any needed modifications such as
pretranslators.
Managing
Extension Lists
An extension list contains extension numbers that you assign and
dedicate to specific dial tone facilities or to specific applications (voice
mail, Auto Attendant, and so on), or both. You can add an extension list
to define a subset of devices, such as fax machines.
The system default extension lists are numbered starting at *0001 in
either a 3-digit or 4-digit plan. By convention, a default extension list
number is preceded by an asterisk. See Table 57 for a description of the
standard extension lists.
CAUTION: Extension lists must not overlap.
Managing Extension Lists
295
Table 57 Extension Lists
Extension List ID Description
*0001
Contains extension numbers assigned to Analog Line Card
ports.
Routes 1 and 2 use this list.
*0002
Contains extension numbers assigned to Digital Line Card ports.
Routes 1 and 2 use this list.
*0003
Contains extension numbers assigned to voice mail.
■
4-digit dial plan: 6400–6499
■
3-digit dial plan: 651-662
Route 3 uses this list.
*0004
Contains the extension for the attendant (that is, the person
who monitors incoming calls). The system automatically assigns
the lowest extension found during Auto Discovery to this list.
Route 4 uses this list.
*0005
Contains extension numbers assigned to H.323 ports.
*0006
Contains extension numbers assigned to Virtual Tie Lines (VTL).
*0008
Contains extension numbers assigned to the 8-pool.
Within an extension list, you can assign a priority to each extension.
When the system accesses an extension list, it tries to use the highest
priority extension first. The highest priority is 1 and the lowest is 99.
For example, if the extension list contains extensions that you assigned to
T1 channels, you can assign unique priorities to each of the extensions. If
you instruct the system to place an outgoing call using the T1 line, it
attempts to use the highest priority extension/channel first. If the first is
unavailable, it tries the next highest priority extension/channel, and so on.
From the Extensions List window, you can perform these tasks:
■
Adding an Extension List
■
Modifying an Extension List
■
Removing an Extension List
The system restricts access to any specific Analog Line Card port or Digital
Line Card port. To dial the extension number that is associated with one
of these devices directly, you must have diagnostic privileges. In addition,
you cannot dial a prefix to obtain a Digital Line Card port.
296
CHAPTER 11: DIAL PLAN
Adding an
Extension List
To add a new extension list:
1 Click Dial Plan > Extension List.
2 Click Add.
3 In the List Extension field, type the number that you want to assign to the
new extension list. Do not select a number that is currently in use by the
system as either an extension or as the number of an extension list.
You may use the default extension number.
4 Type an asterisk preceding the extension number. By convention, the
asterisk indicates that the number represents an extension list.
5 In the Name field, type the name that you want to assign to the new
extension list. Names can include uppercase and lowercase alphanumeric
characters, spaces, underscores, and hyphens.
6 If you want calls to cycle through the extensions in the list, enable the
Cycle Extensions check box. Each time the system accesses the extension
list, it uses the next extension in the list. Calls effectively progress through
the list to balance the load of calls. If you disable the Cycle Extensions
check box, the extension selection always starts from the top of the list.
If an extension in the list has a higher priority, the system uses the highest
priority extension regardless of the Cycle Extension setting.
7 To add an extension to the list:
a If the list does not include any members, click the check boxes next
the extension that you want to add to the list.
b If the list already has members, click Show all to display a list of
extensions that you can add to the list’s membership.
NOTE: You can toggle between the Show all and Show members only
buttons to display extensions that have membership in the list and the
extensions that are not members of the list but which you can add to the
list, and to confirm your changes.
8 To change the priority of an extension, enter a priority number in the field
next to the selected extension (from a high of 1 through a low of 99).
The default value is 50. When the system accesses an extension list, it first
attempts to use the highest priority extension.
9 Click Apply to make the changes and keep this window open or click OK
to make the changes and close the window. Click Reset to restore the
Managing Extension Lists
297
settings back to their original status or click Cancel to return to the
previous window without putting the changes into effect.
Example: If the extension list contains extensions that you assigned to T1
channels, you can assign unique priorities to each extension. If you
instruct the system to place an outgoing call using the T1 line, it attempts
to use the highest priority extension/channel first, and, if the first is
unavailable, tries the next highest priority extension/channel, and so on.
Priorities range from 1 (highest) through 99 (lowest).
CAUTION: If you add an extension list, change the dial plan
configuration file to create a destination route to the new list. This
enables the system to route calls to the new list.
Modifying an
Extension List
To modify an extension list:
1 Click Dial Plan > Extension Lists.
2 Click an extension list.
3 In the List Extension field, type an extension number for the extension list.
4 In the Name field, type a name for the extension list.
If you change the name of an extension list, you invalidate any aspect
of the dial plan that refers to the name. You must change all references
to the extension list name in the dial plan configuration file. If you use an
editor to make changes (rather than modifying the dial plan from within
the NBX NetSet utility), reimport the dial plan.
5 If you want calls to cycle through the extensions in the list, enable the
Cycle Extensions check box. Each time the system accesses the extension
list, it uses the next extension in the list. Calls effectively progress through
the list to balance the load of calls. If you disable the Cycle Extensions
check box, the extension selection always starts from the top of the list.
If an extension in the list has a higher priority, the system uses the highest
priority extension regardless of the Cycle Extension setting.
6 To add an extension to the list:
a If the list does not include any members, click the check boxes next
the extension that you want to add to the list.
b If the list already has members, click Show all to display a list of
extensions that you can add to the list’s membership.
298
CHAPTER 11: DIAL PLAN
NOTE: You can toggle between the Show all and Show members only
buttons to display extensions that have membership in the list and the
extensions that are not members of the list but which you can add to the
list, and to confirm your changes.
7 To change the priority of an extension enter a priority number in the field
next to the extension (from a high of 1 through a low of 99).
The default priority value is 50. When the system accesses an extension
list, it attempts to use the highest priority extension first.
8 Click Apply, or OK to enable your changes and exit the dialog box.
Removing an
Extension List
The system does not let you remove an extension list that the dial plan
is using, even if that extension list is empty. You must remove the
extension list from the dial plan before you can delete the extension list.
To remove an extension list:
1 Click Dial Plan > Extension Lists.
2 Select the extension, or extensions, that you want to delete and click
Remove Selected. To select all extensions, enable the Select check box.
3 Click OK to confirm.
CAUTION: Do not remove any of the predefined lists (lists *0001
through *0008).
Managing
Dial Plan Tables
Determining Which
Devices Use
Dial Plan Tables
The system associates a normal dial plan table and a Least Cost Routing
table with each device. Devices include telephones, Analog Line Card
ports, or Digital Line Card ports. A telephone without an assigned table
does not have permission to dial and is flagged in the dial plan report. For
details, see “Generating a Dial Plan Report” on page 284.
You can view or change the devices associated with a particular dial plan:
1 Click Dial Plan > Tables.
2 From the Dial Plan Tables list:
■
Select (None) to list devices that are not assigned to any table.
Managing Dial Plan Tables
■
299
Select a dial plan table for which you want to list associated devices,
which displays:
■
■
Dial Plan Table ID — The identification number of the dial plan
table as specified in the dial plan configuration file
Dial Plan Table Name — The name of the dial plan table
3 Click Normal to see which devices use table ID 1 (in this example) as the
Normal table.
4 Click Least Cost to see which devices use table ID 1 as the Least Cost
table. Each device can use only one normal and one least cost table.
5 To add a device to the Devices Using Table list, click Show All and then
click to select an available device from the list.
6 To add a device:
a If the list does not include any devices, click the check boxes next to
the device extensions that you want to add to the list.
b If the list already has devices, click Show all to display a list of devices
that you can add to the list’s membership.
Note: You can toggle between the Show all and Show members only
buttons to display devices that have membership in the device list and the
devices that are not members of the list but which you can add to the list,
and to confirm your changes.
7 Click Apply to make the changes and keep this window open, click OK to
make the changes and close the window, or click Cancel to return to the
previous window without putting the changes into effect.
Removing a
Dial Plan Table
You must not remove any of the predefined tables (Internal, Incoming, or
Least Cost).
CAUTION: You cannot remove a dial plan table if a device is using it.
To remove the table, first remove all devices from the Devices Using Table
list.
To remove a dial plan table:
1 Click Dial Plan > Tables.
2 Select the table, or tables, that you want to delete and click Remove
Selected. To select all tables, enable the Select check box.
3 Click OK to confirm.
300
CHAPTER 11: DIAL PLAN
Managing Dial Plan
Pretranslators
Pretranslators are tables in the dial plan configuration file. Each entry in
a pretranslator table contains a string of one or more digits that the
system compares to incoming or outgoing digits. When the digits match
an entry in the table, the system performs the associated pretranslator
operations.
For more information, see:
Identifying Devices
Using Pretranslators
■
Identifying Devices Using Pretranslators
■
Creating a Pretranslator for VTL Calls
■
Identifying Devices Using Pretranslators for CLI
■
Removing a Pretranslator from the Dial Plan
To view a list of devices and their associated pretranslators, or to associate
a pretranslator with a specific device:
1 Click Dial Plan > Pretranslators.
2 Click a pretranslator or click (None) for devices that have no pretranslator.
The system displays the Device Using window. If you selected (None), you
see a list of devices that do not use a pretranslator. Table 58 describes each
field. The fields are the same for the Devices Using Pretranlator for CLI
dialog box.
3 To add a device to the Devices Using Pretranslator list, click Show All and
then click to select an available device from the list.
4 Click Apply, or OK to save your changes and exit from the window.
Table 58 Pretranslator Fields
Field
Purpose
Pretranslator ID
The identification number of the pretranslator as
specified in the dial plan.
Pretranslator Name
The name of the pretranslator as specified in the dial
plan.
Selected Devices
(Members)
Devices currently using the pretranslator.
Unselected Devices
(Nonmembers)
Devices not using the pretranslator.
To enable a specific pretranslator, update the dial plan. See “Importing
and Exporting Dial Plan Configuration Files” on page 279.
Managing Dial Plan Pretranslators
Creating a
Pretranslator for
VTL Calls
301
Calls from one system to another system over a VTL connection include
caller ID information that includes the IP address of the caller’s system and
the caller’s extension. The “*” character separates each field of numbers
in this caller ID string. For example, if extension 1002 on System A calls
someone on system B over a VTL connection, the display panel on the
System B telephone displays 10*234*208*2*1002, which indicates an
incoming call from extension 1002 on the system with the IP address
10.234.208.2.
If the System B dial plan has a pretranslator that removes the IP address
when the call arrives at System B, (see Figure 14 on page 302), the
display panel on the System B telephone displays the calling extension
and no IP address or “*” characters. This solution works well when the
extensions on System A and System B do not overlap, for example,
System A user extensions are 1000-1999 and System B extensions are
2000-2999.
Call Detail Reports (CDR) Records
CDR records incorporate caller ID information to identify a caller. VTLs
transmit a maximum of 30 characters for the caller ID. Because the caller
ID for incoming VTL calls also includes the IP address before the extension
number, the 31st and subsequent characters are dropped from the caller
ID. Consequently, the CDR records may contain abbreviated caller ID
information. If you enable CDR and VTL, add a pretranslator to avoid
inaccurate data.
Site Codes
If the dial plan on System B uses a site code, such as 69, for VTL calls to
System A, you can create a pretranslator that prepends the site code after
it removes the IP address. (See Figure 15 on page 303.) This pretranslator
would provide caller ID information that the System B extension can use
to return a call to the System A extension. For example, a call from
System A (10.234.208.2) extension 1002 would appear on a System B
telephone’s display panel as 691002 instead of 10*126*14*200*1002. The
pretranslator removes the IP address and prepends the calling extension
with the System A site code, 69.
You may choose to not implement this pretranslator if calls from System
A can hop off at System B onto a PRI line because the site code would be
included as caller ID information about the PRI line, and that caller ID
302
CHAPTER 11: DIAL PLAN
information would be meaningless to someone outside the system. For
hop-off calls, you can create a separate pretranslator.
VTL Calls, Caller ID and Hop Off
If a VTL call from System A to System B hops off System B and onto an
ISDN PRI trunk, the “*” characters in the caller ID string can present
problems for the PRI service. The PRI service cannot interpret the “*”
symbols so it ignores the caller ID string it has received and instead uses
the PRI line telephone number. For example, if you must dial
1-508-555-1234 to access the PRI externally, that number is used for the
outgoing caller ID. If System A or System B has CLIR (Calling Line Identity
Restriction) enabled, the PRI service ignores the CLIR setting and it sends
the PRI line telephone number as the caller ID.
If you have a pretranslator on System B that removes the IP address from
the caller ID string of incoming VTL calls, then the caller ID will be the
extension of the telephone making the call. If system A and/or System B
has CLIR enabled, then CLIR will be in effect. The only exception is for
emergency calls (as defined in System B's dial plan), which never have
caller ID blocked.
Figure 14 shows an example of a pretranslator that removes the “*”
character from VTL calls that originate on a system with the IP address
10.234.208.2. The Value column of the PreTranslatorOperation Create
line of Figure 14 specifies how many digits to strip from the beginning of
the string. That value depends on the length of the received IP address. In
the example, the IP address, 10*234*208*2, is 12 digits, and then you
must also count the trailing “*” in the string. That trailing “*” is the
character that separates the IP address from the caller extension and you
must count it when you specify the number of digits to remove.
Figure 14 Pretranslator to Remove IP Address
PreTranslator Create 2 VTL
/
/
PreTranslatorEntry Create
PreTransId Entry Digits
---------- ----- -----2
1 10*234*208*2*
/
PreTransId Entry OperId Operation Value
/
---------- ----- ------ --------- ----PreTranslatorOperation Create
2
1
1 stripLead 13
Managing Dial Plan Pretranslators
303
Figure 15 shows an example of a pretranslator that removes the “*”
character from VTL calls that originated on a system with the IP address
10.234.208.2 and prepends the site code, 69, of system 10.234.208.2.
Figure 15 Pretranslator to Remove IP Address and Prepend Site Code
PreTranslator Create 2 VTL
/
/
PreTranslatorEntry Create
PreTransId Entry Digits
---------- ----- -----2
1 10*234*208*2*
/
PreTransId
/
---------PreTranslatorOperation Create
PreTranslatorOperation Create
Entry OperId
----- -----2
1
2
1
Operation Value
--------- ----1 stripLead 13
2 prepend
69
To add a pretranslator for VTL caller ID issues:
1 Open your dial plan for editing as described in “Accessing the
Dial Plan”on page 278.
2 Search for the section titled Pretranslators.
3 Add a new pretranslator for each system from which you will be receiving
calls over a VTL.
4 Save the edited dial plan and import it into the system. For more
information, see “Importing and Exporting Dial Plan Configuration Files”
on page 279.
5 Specify the devices that use the pretranslator. See “Adding VTL Devices to
the Pretranslators (Optional)” on page 343.
Identifying Devices
Using Pretranslators
for CLI
To view a list of devices that use a particular pretranslator to present
Calling Line ID (CLI) information about outgoing calls:
1 Click Dial Plan > Pretranslators.
2 Click a pretranslator or click (None) for devices that have no pretranslator.
3 Click the Device Using CLI tab
If you selected (None), you see a list of devices that do not use a
pretranslator for Calling Line ID.
4 To add a device to the list, click Show All and then click to select an
available device from the list. See Table 58 for field descriptions.
304
CHAPTER 11: DIAL PLAN
5 Click Apply to make the changes and keep this window open, click OK to
make the changes and close the window, or click Cancel to return to the
previous window without putting the changes into effect.
Removing a
Pretranslator from
the Dial Plan
To remove a pretranslator:
1 Click Dial Plan > Pretranslators and select a pretranslator from the scroll
list.
2 Select the pretranslator, or pretranslators, that you want to delete and
click Remove Selected. To select all pretranslators, enable the Select check
box.
3 Click OK.
CAUTION: You cannot remove a pretranslator if any device is currently
using it. If you want to remove the pretranslator, first remove all devices
from the Devices Using list.
Configuring the
Dial Plan for the
4ESS Protocol (T1)
The 4ESS protocol, used on T1 Digital Line Cards that are configured for
PRI operation, requires specific configuration entries in the system dial
plan. If you purchase the 4ESS protocol and SDN (Software Defined
Network) service from your long-distance carrier, you must make dial plan
changes similar to those outlined in “Configuring the Dial Plan for SDN
Calls” on page 304. If you want to make long distance calls or
international long distance calls using the 4ESS protocol, you must make
dial plan changes similar to those outlined in “Configuring the Dial Plan
for North American Long Distance” on page 305 and “Configuring the
Dial Plan for International Long Distance” on page 305.
Configuring the Dial Plan for SDN Calls
If you use the 4ESS protocol and want to make SDN calls, in the system
dial plan, configure a unique route to use for SDN calls and include the
letters SDN at the beginning of the dial string.
Example: The dial plan entry shown in Figure 16 adds the characters
SDN, which must be upper case letters, before the long-distance dialed
digits. This example assumes that SDN calls use route 4.
Configuring the Dial Plan for the 4ESS Protocol (T1)
305
Figure 16 Dial Plan Entries for SDN
/
Route Entry OperID Operation Value
/
----- ----- ------ --------- ----DestinationRouteOperation Create
4
1
1
prepend
SDN
Configuring the Dial Plan for North American Long Distance
If you use the 4ESS protocol and want to make long-distance calls, in the
system dial plan, remove any digits that are dialed by telephone users to
access the long-distance service from the dial string. For example, if
telephone users normally dial 9 and then 1 to obtain a long-distance dial
tone, and then dial a 10-digit number, the dial plan must remove the 9
and the 1 and present only the 10-digit number to the long-distance
carrier. Otherwise, the 4ESS protocol rejects the call.
Example: If you use route 1 in the dial plan for Long Distance, and
telephone users must dial 91 to make a long-distance call, the dial plan
entries shown in Figure 17 remove the first two digits (91) and submit the
remaining 10 digits to the long-distance carrier.
Figure 17 Dial Plan Entries for North American Long Distance
Table Create 1 Internal 4 Digit Extensions
/
ID Entry Digits Min Max Class
Prio Route
/
-- ----- ------ --- --- ------------ ---- ----TableEntry Create 1
2 91
12 12 LongDistance
0
1
/
Route Entry OperID Operation Value
/
----- ----- ------ --------- ----DestinationRouteOperation Create
1
1
1
stripLead
2
Configuring the Dial Plan for International Long Distance
If you use the 4ESS protocol and you want to make international
long-distance calls, in the dial plan, remove from the dial string the digits
9011 that are dialed by telephone users to access the international
long-distance service. For example, if the telephone user dials the string
9-014-1234-567890, the dial plan must remove 9011 before it passed
the dialed digits to the long-distance carrier or the 4ESS protocol rejects
the call. See Figure 18.
306
CHAPTER 11: DIAL PLAN
Figure 18 Dial Plan Entries for International Long Distance
Table Create 1 Internal 4 Digit Extensions
/
ID Entry Digits Min Max Class
Prio Route
/
-- ----- ------ --- --- ------------ ---- ----TableEntry Create 1
3 9011
12 64 International
0
1
/
Route Entry OperID Operation Value
/
----- ----- ------ --------- ----DestinationRouteOperation Create
3
2
1
stripLead
Dial Plan
Configurations and
VPIM
4
With Voice Profile for Internet Mail (VPIM), telephone users on one
system can send voice mail to a user on another VPIM-compliant system.
For detailed information about VPIM and how to configure VPIM settings,
see “Voice Profile for Internet Mail” on page 227
To send a voice mail message to a user on another VPIM-compliant
system, a telephone user first composes the voice mail message, using
the commands in the user’s voice mailbox. Depending on how you
configure the system’s dial plan, the telephone user can specify the
destination in two ways:
■
If the dial plan is configured for site codes, the telephone user
specifies the destination site code followed by the extension of the
person for whom the voice mail message is intended.
■
If the dial plan is configured without site codes, the telephone user
specifies the extension of the person for whom the message is
intended. This requires that each site use a unique extension range for
telephones.
A telephone user who knows the IP address of a VPIM-compliant voice
mail system and the extension of a person who uses that system can
compose a voice mail message and then send it using these steps:
1 Dial the IP address, pressing the * key after each field in the address,
including the last field.
2 Dial the extension of the person followed by # key.
You must decide whether to use site codes or unique extension ranges
when you configure the dial plan.
Configuring the Dial Plan for VPIM
Configuring the
Dial Plan for VPIM
307
To define a VPIM connection between two systems, create entries in the
dial plan for the following items:
■
The digit sequence that a telephone user must dial to access the VPIM
connection
■
The route number that is used to access the other NBX system
■
The extension list to which the VPIM route belongs
■
The operations that must be performed on the dialed digits to create
the appropriate outgoing digit sequence
Figure 19 contains sample lines which, when added to an existing dial
plan, implement VPIM connections to two other systems, one in Atlanta
and one in Dallas. Table 59 explains each entry.
Figure 19 Dial Plan with VPIM Implementation Commands
Table Create 1 Internal Extensions
/
Id Entry Digits
Min Max Class
/
-- ----- ----------- --- --- ------------TableEntry Create
1
45 V82
5
5 WAN
TableEntry Create
1
46 V83
6
6 WAN
Prio Route
---- ----0
532
0
533
/
Route Description
/
----- ----------DestinationRoute Create
532 Atlanta VPIM Connection
DestinationRoute Create
533 Dallas VPIM Connection
/
Route Entry DestinationExtension
/
----- ----- -------------------DestinationRouteEntry Create
532
1 *0003
DestinationRouteEntry Create
533
1 *0003
/
Route Entry OperId Operation
/
----- ----- ------ --------DestinationRouteOperation Create
532
1
1 stripLead
DestinationRouteOperation Create
532
1
2 prepend
Value
----3
10*234*101*222*
308
CHAPTER 11: DIAL PLAN
Table 59 Explanation of Entries in Figure 19
Field
Purpose
Table Create 1 Internal Extensions
This command is present in all default dial plans. It
is included here as a reference point for
subsequent commands.
TableEntry Create 1
45
V82
5 5 WAN
0 532
TableEntry Create 1 45
This portion of the command creates entry 45 in
dial plan table 1 (the Internal Extensions table). The
choice of 45 as the entry number depends on how
many entries exist in table 1. This example assumes
that the highest number assigned to a previously
existing entry was 44.
V82 (Digits column)
The required upper case letter V indicates that this
is a VPIM connection. The number 82 indicates
that telephone users must dial 82 to access the
VPIM connection and then dial the extension they
want to reach.
You can select any number of digits for a site
code. The selected number must not conflict with
other dial plan entries. This example assumes that
82 is not used in any other way in the dial plan.
NOTE: Long digit sequences can a create an
opportunity for dialing errors.
Min (5) Max (5)
Indicates that the total digit sequence the
telephone user dials is 5 digits. The first two digits
are the site code (82 in this example) and the
remaining 3 digits are the destination extension.
Class (WAN)
Indicates that this call is classified as WAN. All
VPIM calls have this classification.
Priority (0)
This field is unused by the dial plan; the default
value is zero (0).
Route (532)
In this example, the VPIM connection to the other
NBX system uses route 532. The route number
must be unique in the dial plan and in the range of
1–32768.
DestinationRoute Create 532 Atlanta VPIM Connection
This command creates route number 532 and
names it Atlanta VPIM Connection.
DestinationRouteEntry Create 532
1 *0003
This command (mandatory for all VPIM routes)
assigns route 532 to the extension list *0003.
DestinationRouteOperation Create 532
1
1 stripLead 3
Dial Plan Configuration File Commands
309
Table 59 Explanation of Entries in Figure 19 (continued)
Field
Purpose
For DestinationRoute 532, entry 1, this command
creates operation 1, which removes the first three
digits, including the letter V, from the digit string,
leaving only the extension that the telephone user
dials.
DestinationRouteOperation Create 532
1
2 prepend
10*234*101*222*
For DestinationRoute 532, entry 1, this command
creates operation 2, which places the string
10*234*101*222* in front of the extension. This
string represents the IP address of the target NBX
system. You must use the star character (*) to
separate the fields within the IP address and to
separate the IP address from the extension field.
Dial Plan
Configuration File
Commands
Dial Plan Command
Summary
This section provides the syntax and description of each command used
to create the information in the dial plan configuration file. See these
sections for detailed information:
■
“Dial Plan Command Format” on page 268.
■
Table 60 on page 310, which categorizes and summarizes all the dial
plan commands.
■
“Dial Plan Command Summary” on page 309, which is a description
of each component of dial plan commands.
■
“List of Dial Plan Commands” on page 311, which is the alphabetical
list of dial plan commands that provides a detailed description and
syntax of each command.
■
“Sample Solutions Using Dial Plan Configuration File Commands” on
page 324 shows how these commands are implemented in a dial
plan. You can also open and examine any of the dial plans that are
shipped with your system.
Table 60 provides a brief summary of the dial plan commands. The
summary lists and categorizes these commands in the order that they
may logically appear in a working dial plan.
See “List of Dial Plan Commands” on page 311 for a complete list and
description of each dial plan command, including syntax and arguments.
310
CHAPTER 11: DIAL PLAN
Command syntax is case insensitive. In the sample dial plans supplied
with the system, and in this section, commands use upper and lower case
to make them easier to read.
An entry that begins with “n” for example, nDialPlanID, indicates an
integer field. Integer IDs are used in many places, and must be within
the range 1 through 32768. The system reserves dial plan table ID
numbers 1, 2, and 3 for Internal, Incoming, and Least Cost Routing,
respectively.
An entry that begins with “sz” (for example, szDescription) indicates a
field composed of alphanumeric characters. Acceptable characters are
a through z, A through Z, and 0 through 9.
Each line in the configuration file must contain a complete command.
The system reads all lines in the configuration file, and ignores only those
lines containing one or more syntax errors. The system treats any line that
begins with / (forward slash) as a comment and ignores it.
CAUTION: Do not place comments at the end of a command line.
Table 60 Dial Plan Command Summary
Command Name
Description
Table Create
Creates a dial plan table.
TableEntry Create
Creates an entry in a dial plan table.
DestinationRoute Create
Creates a route that specifies the primary and
alternative destination device of a call.
DestinationRouteEntry Create
Creates a destination route entry that
identifies a single destination device or device
list.
DestinationRouteOperation Create
Creates a digit manipulation operation for a
destination route entry.
TimedRoute Create
Creates a timed route (a route that the system
uses based on defined criteria for time of day
and day of week).
TimedRouteEntry Create
Creates a timed route entry specifying either a
time of day or system mode, day of the week
criteria, and the destination route to use if
that criteria are met.
TimedRouteOperation Create
Creates a digit manipulation operation for a
timed route entry.
Dial Plan Configuration File Commands
311
Table 60 Dial Plan Command Summary (continued)
List of Dial Plan
Commands
Command Name
Description
PreTranslator Create
Creates a pretranslator entry and specifies a
string of digits that are compared to the
incoming digits.
PreTranslatorEntry Create
Creates a pretranslator entry and specifies a
string of digits that are compared to the
incoming digits.
PreTranslatorEntry Delete
Deletes a pretranslator entry or deletes all
entries for a particular pretranslator.
PreTranslatorOperation Create
Creates a digit manipulation operation for a
pretranslator entry.
ExtensionLength
Specifies the length of extension numbers for
system devices.
ExtensionRange
Specifies a range of extensions for each type
of device.
ExternalSettings
Specifies settings for several aspects of
external devices.
The dial plan commands are described in this section. They are listed in
alphabetical order:
■
DestinationRoute Create
■
DestinationRouteEntry Create
■
DestinationRouteOperation Create
■
ExtensionLength
■
ExtensionRange
■
ExternalSettings
■
PreTranslator Create
■
PreTranslatorEntry Create
■
PreTranslatorEntry Delete
■
PreTranslatorOperation Create
■
Table Create
■
TableEntry Create
■
TimedRoute Create
■
TimedRouteEntry Create
312
CHAPTER 11: DIAL PLAN
■
DestinationRoute Create
TimedRouteOperation Create
Syntax
DestinationRoute Create nRouteId szDescription
Description Creates a route that specifies the primary and alternative
destination device of a call (for example, which CO Line or Digital Line
Card port over which to route the call). If the destination route already
exists, this command removes all of its entries and operations, and
overwrites its description with the new information.
Arguments
nRouteId — An integer in the range 1 – 32768, uniquely identifying this
destination route.
szDescription — The description or name of the destination route.
Example: This example creates destination route 3 and names it “Voice
Application”: DestinationRoute Create 3 Voice Application
DestinationRouteEntry
Create
Syntax
DestinationRouteEntry Create nRouteId nEntryId szExtension
Description creates a destination route entry that identifies a single
destination device or device list.
If the specified destination route entry already exists, this command
overwrites it with the new information. During routing, the system
checks the list of destinations in ascending nEntryId order (nEntryId 1 first).
Arguments
nRouteId — An integer in the range 1 through 32768.
nEntryId — An integer in the range 1 through 32768. The system checks
the list of destinations in ascending nEntryId order, and uses the first
available one.
szExtension — The extension of the destination device or device list. Note
that the system does not dial this extension (that is, it neither checks the
extension against a dial plan nor subjects it to Class of Service restrictions,
digit manipulation, or routing) but instead uses the extension only to look
up the device in the internal device directory.
Dial Plan Configuration File Commands
313
Example: This example command creates, in route table 3, entry 1
and defines extension list *0003 as the destination for this route entry.
Extension list *0003 contains the voice mail extensions/ports.
DestinationRouteEntry Create 3 1 *0003
DestinationRouteOperati
on Create
Syntax
DestinationRouteOperation Create nRouteId nEntryId nOperId
szOperation szValue
Description Creates a digit manipulation operation for a destination
route entry. If the specified digit manipulation operation already exists,
this command overwrites it with the new information. During routing the
system processes the entire list of operations in ascending nOperId order
(nOperId 1 first).
Arguments
RouteId — An integer in the range 1 through 32768.
nEntryId — An integer in the range 1 through 32768 specifying the
destination route entry to which this operation applies.
nOperId — An integer in the range 1 through 32768. The system
processes the list of operations in ascending nOperId order.
szOperation — The name of the digit manipulation operation to perform:
stripLead, stripTrail, replace, prepend, append.
szValue — A value used by the operation, either the string of digits to
prepend, append, replace with, or the number of digits to strip.
Example: This example command creates, for destination route 3,
entry 1, an operation numbered 1, with the associated function
stripLead, and an argument of 1, indicating that the command removes
(strips) one leading digit from the dialed number before dialing.
DestinationRouteOperation Create 3 1 1 stripLead 1
ExtensionLength
Syntax
ExtensionLength nExtensionLength
Description The length of extension numbers for system devices. The
default is 4 for V3000, V3001, V3001R, and V5000 systems. The default
is 3 for NBX 100 systems.
314
CHAPTER 11: DIAL PLAN
Arguments
nExtensionLength — specifies either 3 to designate a a 3-digit dial plan, or
4 to designate a 4-digit dial plan.
ExtensionRange
Syntax
ExtensionRange szExtensionType szLowestExtension szHighestExtension
Description A range of extensions for each type of device. When the
system automatically generates extensions it assigns them from within
this range. When you manually generate an extension number, verify that
it is within the valid range. During a dial plan import operation, the
system does not validate that existing extensions are within the specified
range. 3Com strongly recommends that you configure the dial plan
before you define any devices in the system.
Dial Plan Configuration File Commands
315
Arguments
szExtensionType — One of these: Telephone, Park, Auto Attendant, Hunt
Group, External.
szLowestExtension — The lowest extension for this device type.
szHighestExtension — The highest extension for this device type.
Example: These commands define the extension range for telephones as
100 through 449, for call park as 601 through 609, for Auto Attendants
as 500 through 599, for hunt groups as 450 through 499, and for
external lines as 600 through 799.
ExtensionRange
ExtensionRange
ExtensionRange
ExtensionRange
ExtensionRange
Telephone 100 449
Park 601 609
Autoattendant 500 599
HuntGroup 450 499
External 600 799
CAUTION: Do not define extension ranges that overlap. The only
exception is Park, which must be within the External range.
ExternalSettings
Syntax
ExternalSettings szExternalKeysetPrefix
szFirstAutoDiscoverExtension szDefaultAutoExtension
Description Specifies settings for several aspects of external devices.
Arguments
szExternalKeysetPrefix — The digits that are prepended to external calls
made in Keyset mode. This is used to define the Class of Service (CoS) for
external calls made in Keyset mode. Typical values for this digit are 8, 9,
or 0 (zero). This prefix is set to the appropriate number in each country’s
dial plan.
Example: In the default internal dial plan table, the digit 9 instructs the
system to connect the call to an external line. When a telephone has a
button mapped to an external device, and the user places a call using
that external device, the system prepends the szExternalKeysetPrefix digit
to the digits dialed by a user; then the system applies the dial plan tables
to define call Class of Service.
316
CHAPTER 11: DIAL PLAN
szFirstAutoDiscoverExtension — The first extension used when
autodiscovering external devices. This must be in the specified range of
lowest/highest external extensions.
The system assigns extensions starting with this number and
incrementing upward. For information about the Auto Discovery topic,
see “Using Auto Discovery for Initial System Configuration” in the
NBX Installation Guide.
The default value for a 3-digit system is 750, and for a 4-digit system is
7250. Typically, systems do not use all of the extensions from 600
through 799 (or 6000 through 7999). If, however, the system uses all of
these extensions and needs another one, it starts looking from the
beginning of the range and selects the first unused one.
szDefaultAutoExtension — The default extension the system uses for
forwarding incoming calls. This is always 500.
The system must direct each incoming call (on an external line) to an
extension. After you import the dial plan configuration file, and complete
the Auto Discovery process, you can manually configure the extension for
each analog line and each Digital Line Card channel, if you want.
PreTranslator Create
Syntax
PreTranslator Create nPreTranslatorId szDescription
Description Creates a pretranslator. If the pretranslator already exists,
this command removes all of its entries and operations, and overwrites its
description with the new information.
Arguments
nPreTranslatorId — An integer in the range 1 through 32768.
szDescription — The description or name of the pretranslator.
Example: This command creates a pretranslator, designates it as the first
one (number 1) and give it the title “4-to-3-digit DID/DDI pretranslator.”
PreTranslator Create 1 4-to-3-digit DID/DDI pretranslator
PreTranslatorEntry Create
Syntax
PreTranslatorEntry Create nPreTranslatorId nEntryId szDigits
Dial Plan Configuration File Commands
317
Description Creates a pretranslator entry and specifies a string of digits
that are compared to the incoming digits. If the pretranslator entry
already exists, this command overwrites it with the new information.
Arguments
nPreTranslatorId — An integer in the range 1 through 32768.
nEntryId — An integer in the range 1 through 32768.
szDigits — The digits to compare to the incoming digits.
Example: These example commands create, in pretranslator 1, entries 1
through 10, each of which looks for a different single digit (0 through 9)
in the incoming digits.
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry
PreTranslatorEntry Delete
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
1
1
1
1
1
1
1
1
1
1
1 0
2 1
3 2
4 3
5 4
6 5
7 6
8 7
9 8
10 9
Syntax
PreTranslatorEntry Delete nPreTranslatorId nEntryId
Description Deletes a pretranslator entry or deletes all entries for a
particular pretranslator.
Use caution when using this command to delete Pretranslator entries in
an existing dial plan. In general, it is best to delete all tables, routes, and
pretranslators at the beginning of each dial plan configuration file. This
precaution avoids the potential conflicts or unpredictable actions caused
by importing new dial plan entries on top of an existing dial plan.
For instructions on how to edit the dial plan configuration file to delete
existing tables, routes, and pretranslators, see “Creating Dial Plan
Configuration Files” on page 278.
Arguments
318
CHAPTER 11: DIAL PLAN
nPreTranslatorId — An integer in the range 1–32768.
nEntryId — An integer in the range 1–32768 or * for all entries.
Example: This command deletes pretranslator entry 3 from
pretranslator 2.
PreTranslatorEntry Delete 2 3
This command deletes all pretranslator entries from pretranslator 2.
PreTranslatorEntry Delete 2 *
Normally this command is not necessary. It is better to delete an entire
dial plan rather than import a new dial plan over it. To accomplish this,
3Com recommends using specific commands at the top of every dial plan
configuration file. For an example of this technique, see “Creating Dial
Plan Configuration Files” on page 278.
PreTranslatorOperation
Create
Syntax
PreTranslatorOperation Create nPreTranslatorId nEntryId
nOperId szOperation szValue
Description Creates a digit manipulation operation for a pretranslator
entry. If the specified digit manipulation operation already exists, this
command overwrites it with the new information. During pretranslation,
the system processes the list of operations in ascending nOperId order
(nOperId 1 first).
Arguments
nPreTranslatorId — An integer in the range 1 through 32768.
nEntryId — An integer in the range 1 through 32768 specifying the
pretranslator entry to which this operation applies.
nOperId — An integer in the range 1 through 32768. The
system processes the list of operations in ascending nOperId order
(nOperId 1 first).
szOperation — The name of the digit manipulation operation to perform.
Values are: stripLead, stripTrail, replace, prepend, append.
szValue — The value to use in the operation, either the string of digits to
prepend, append, replace with, or the number of digits to strip.
Dial Plan Configuration File Commands
Table Create
319
Syntax
Table Create nDialPlanTableId szDescription
Description Creates a dial plan table to control the routing of calls
placed by devices. Dial plan tables apply to internal devices such as
telephones, incoming calls from outside the system, and Least Cost
Routes. If the dial plan table already exists, this command removes all
entries from the table, and fills the table with the new information.
Arguments
nDialPlanTableId — An integer in the range 1 through 32768. The default
dial plan tables use ID numbers 1 through 3:
1 — Internal dial plan table
2 — Incoming dial plan table
3 — Least Cost Routing table
szDescription — The description or name of the dial plan table. The NBX
NetSet utility uses this name to refer to the table.
Example: This example command creates dial plan table 1 and names it
“Internal 4 Digit Extensions.”
Table Create 1
TableEntry Create
Internal 4 Digit Extensions
Syntax
TableEntry Create nDialPlanTableId nEntryId szDigits
nMinDigits nMaxDigits szCallClass nPriority nRouteId
Description Creates an entry in a dial plan table that specifies a string
of digits that are compared to the dialed digits. If the dial plan table entry
already exists, this command overwrites it with the new information.
Dial plan table entries make Class of Service and call routing decisions
based on the correspondence of dialed digits and table entry digits.
Arguments
nDialPlanTableId — An integer in the range 1 through 32768. The system
reserves three ID numbers:
1 — Internal dial plan table
2 — Incoming dial plan table
320
CHAPTER 11: DIAL PLAN
3 — Least Cost Routing table
nEntryId — An integer in the range 1 through 32768. Each entry must
have a unique ID. If two entries have the same ID, the system uses the
entry closer to the bottom of the configuration file (the one processed last).
szDigits — A string of dialed digits in a dial plan entry.
nMinDigits — An integer specifying the minimum number of digits to
collect.
nMaxDigits — An integer specifying the maximum number of digits to
collect.
szCallClass — The call class for this dial plan entry. The call class
corresponds to permissions granted to users in their Class of Service.
Values are Internal, Local, LongDistance, International, WAN, TollFree,
Emergency, COCode, Wireless, Other, Toll, AlternateLong, Operator,
TrunkToTrunk, Diagnostics, and NotAllowed.
nPriority — Not presently used. Always set to zero (0).
nRouteId — An integer specifying the ID of the route to use when this dial
plan entry is matched. A route ID of zero (0) indicates that this entry has
no defined route; digits are transmitted ed as soon as they are dialed.
Example: This example command creates (in table ID 1) table entry 1,
which looks for 3 as the first digit in a 4-digit string (minimum and
maximum number of characters are both specified as 4), classifies the call
type as “Internal”, assigns the call a priority of zero (the only acceptable
priority in this product release). Because the destination is an internal
extension, there is no need for a defined route so the route number is zero.
TableEntry Create
TimedRoute Create
1 1
3
4 4
Internal
0 0
Syntax
TimedRoute Create nRouteId nDefaultDestinationRouteId
szDescription
Description Creates a timed route (a route that the system uses based
on defined criteria for time of day and day of week). If the timed route
already exists, this command removes all of its entries and overwrites its
description and defaultDestinationRoute with the new information.
Dial Plan Configuration File Commands
321
Arguments
nRouteId — An integer in the range 1 through 32768 which uniquely
identifies this timed route.
nDefaultDestinationRouteId — An integer in the range 1 through 32768
identifying the destination route the system must use if none of the
entries in this timed route match the current time of day.
szDescription — A description or name of the timed route.
Example: This example command creates timed route 7 which uses
destination route 1, defined in the “Routes” section of the system
configuration file. The description of route 7 is “Business Hours Long
Distance.”
TimedRoute Create 7 1 Business Hours Long Distance
TimedRouteEntry Create
Syntax
TimedRouteEntry Create nRouteId nEntryId szStartTime
szEndTime szDaysOfWeek nDestinationRouteId
Description Creates a timed route entry specifying either a time of day
or system mode, day of the week criteria, and the destination route to
use if that criteria are met. If the specified timed route entry already
exists, this command overwrites it with the new information. During
routing, the system checks the list of timed route entries in ascending
nEntryId order (nEntryId 1 first). The system performs any digit
manipulation operations that apply to the specified destination.
Arguments
nRouteId — An integer in the range 1 through 32768.
nEntryId — An integer in the range 1 through 32768. The system checks
the list of timed routes in ascending order based on nEntryId.
szStartTime — Start time in 24-hour format, for example, 13:30 for
1:30 p.m. You can use either 24:00 or 00:00 to specify midnight. Instead
of specifying times, you can enter a system mode name (open, closed,
lunch, or other). For each system mode, the system knows the start and
stop times. If you use one of the system modes, both szStartTime and
szEndTime parameter must be the same.
322
CHAPTER 11: DIAL PLAN
You define start and end times for system modes through the NBX NetSet
utility. Click System-Wide Settings > Business Hours. Enter the times that
you want and click OK.
Example: If you define business hours from 8:00 to 17:00 on Mondays,
Wednesdays and Fridays, and from 9:00 to 18:00 Tuesdays and
Thursdays, then a timed route entry both szStartTime and szEndTime set
to “open” applies differently on Monday, Wednesday, and Friday than on
Tuesday and Thursday.
You set the beginning and ending times for open, lunch, and other using
the NBX NetSet utility. Click System-Wide Settings > Business Hours. The
system treats all times not included these three categories as closed.
szEndTime — End time in 24-hour format, for example, “18:30” for
6:30 p.m. You can use either 00:000 or 24:00 to indicate midnight. If you
use a system mode (open, lunch, or other) for szStartTime, you must use
the same system mode for szEndTime.
szDaysOfWeek — A seven character mask in which each character
position represents one day of the week, beginning with Sunday as the
first character and ending with Saturday as the last character. The system
excludes any day if a dot “.” character appears in that day's position. (As
a convention, you place the first letter of each day in the appropriate
character position to indicate that the day is included, but you can use
any letter you want; the presence of a dot “.” in a given position excludes
the day of the week and the presence of any other character in that
position selects that day.
You use the szDaysOfWeek parameter to specify when this timed route is
active. You can specify that the timed route entry apply to all days of the
week. If you specify the start and end times for open mode differently on
some days of the week than for other days, one timed route entry can
operate differently depending on the day.
Example: The system interprets “SMT.T.S” (or “XXX.X.X”) as “all days
except Wednesday and Friday.” The “dot” characters in positions four
and six exclude the fourth and sixth days of the week (Wednesday and
Friday).
nDestinationRouteId — The Id of the destination route to use if this entry’s
time of day and day of week criteria are met.
Dial Plan Configuration File Commands
323
Example: This example command creates two entries, one to define the
route to use during business hours (open) and the other to define the
route when the business is closed.
The first entry is timed route 7, timed route entry 1. The two occurrences
of the word “Open” instruct the system to use the start time and end
time defined by the “open for business” hours, and the letters
“SMTWTFS” indicate that this entry applies to all seven days of the week
(Sunday through Saturday).
The number 6 designates destination route 6, defined in the system
routes table. Because this entry applies to the “open for business” hours,
route 6 could define a least cost route for outgoing long distance calls.
The second entry is timed route 7, timed route entry 2. The two
occurrences of the word “Closed” instruct the system to use the start
time and end time defined by the “business closed” hours, and the
letters “SMTWTFS” indicate that this entry applies to all seven days of the
week (Sunday through Saturday). The number 3 designates destination
route 3, defined in the system routes table. Because this route applies to
the “business closed” hours, route 3 could connect the incoming call to
an Auto Attendant menu that tells the caller that the company is closed
and gives instructions on how to leave a message and how to reach
someone in an emergency.
TimedRouteEntry Create 7 1 Open Open SMTWTFS 6
TimedRouteEntry Create 7 2 Closed Closed SMTWTFS 3
TimedRouteOperation
Create
Syntax
TimedRouteOperation Create nRouteId nEntryId nOperId
szOperation szValue
Description Creates a digit manipulation operation for a timed route
entry. If the specified digit manipulation operation already exists, this
command overwrites it with the new information. During routing, the
system processes the list of operations in ascending nOperId order
(nOperId 1 first).
CAUTION: Timed route operations are performed before
Destination Route operations. So if you strip a leading 9 using a
TimedRouteOperation Create command verify that you don't mistakenly
perform the same action in a DestinationRouteOperation Create
command. If you made that error, you would lose the first dialed digit.
324
CHAPTER 11: DIAL PLAN
Arguments
nRouteId — An integer in the range 1 through 32768.
nEntryId — An integer in the range 1 through 32768 specifying the timed
route entry to which this operation applies.
nOperId — An integer in the range 1 through 32768. The
system processes the list of operations in ascending nOperId order
(nOperId 1 first).
szOperation — The name of the digit manipulation operation to perform:
stripLead, stripTrail, replace, prepend, append.
szValue — The value used by the operation, either the string of digits to
prepend, append, replace with, or the number of digits to strip.
Sample Solutions
Using Dial Plan
Configuration File
Commands
This section describes several requirements that a customer may have,
and for each one, provides a sample solution. An explanation follows
each step in the solution.
For a detailed explanation of each command, see “Dial Plan
Configuration File Commands” on page 309.
Customer Requirement 1. Assume that the telephone company
passes 4-digit numbers to the system for each incoming telephone call
(for example, numbers in the range 5200 through 5300). If the system
uses 3-digit extensions in the range 200 through 300, you could define a
single pretranslation operation that performed a stripLead to remove the
first digit. For example, the system could remove the number five from an
incoming number such as 5278, and pass the call to extension 278.
To accomplish the pretranslation:
PreTranslator Create 1 4-to-3-digit T1 DID/DDI Pretranslator
Explanation: Create pretranslator table 1, called “4-to-3-digit T1
DID/DDI Pretranslator.”
PreTranslatorEntry Create 1 1 5
Explanation: Create, in pretranslator table 1, entry number 1, which
applies when the first digit in the sequence is 5.
PreTranslatorOperation Create 1 1 1 stripLead 1
Sample Solutions Using Dial Plan Configuration File Commands
325
Explanation: For pretranslator table 1, PreTranslatorEntry 1, create the
first PreTranslatorOperation. This performs a stripLead operation,
removing a single leading digit from the incoming number.
Customer Requirement 2. Assume that the telephone company
passes 10-digit numbers to the system for each incoming telephone call
(for example, numbers in the range 4567-89-3000 through
4567-89-3500). If the system uses 4-digit extensions in the range 2000
through 2500, you can pass an incoming 10-digit number such as
4567-89-3210 to extension 2210 by using two pretranslation operations.
The first operation performs a stripLead operation to remove the first 7
digits, leaving 210. The second would perform a prepend to add the digit
2 to the front of the number, creating 2210, which matches an extension
within the extension range.
These entries in a dial plan configuration file would accomplish the
pretranslation:
PreTranslator Create 1 10-to-3-digit T1 DID/DDI Pretranslator
Explanation: Create pretranslator table 1, called “10-to-3-digit T1
DID/DDI Pretranslator.”
PreTranslatorEntry Create 1 1 4567893
Explanation: Creates the first entry in pretranslator table 1. This entry
looks for sequence of digits 4567893.
This example assumes that all numbers begin with the same 7 digits
(4567-89-3) and differ only in the last 3 digits. If this assumption is
incorrect, you can add PreTranslatorEntry Create lines to describe all of
the possible variations.
PreTranslatorOperation Create 1 1 1 stripLead 7
PreTranslatorOperation Create 1 1 2 prepend 2
Explanation: For PreTranslator table 1, PreTranslatorEntry 1, create the
first PreTranslatorOperation. This performs a stripLead operation,
removing the first seven leading digits from the incoming number.
Then create operation 2, which prepends the digit 2 to the remaining
3-digit number. The resulting 4-digit number matches one of the internal
extensions in the system.
Customer Requirement 3. Assume that the telephone company
assigns a group of 4-digit DID/DDI numbers from 6000 through 6199;
however, you want to use internal telephone extensions from 3000
326
CHAPTER 11: DIAL PLAN
through 3199. Also, you want the number 6111 to connect the caller to
an Auto Attendant line for the customer service group.
Add these lines to the dial plan configuration file:
PreTranslator Create 1 6XXX to 3XXX Translator
Explanation: Creates PreTranslator 1, and names it “6XXX to 3XXX
Translator”
PreTranslatorEntry Create 1 1 6111
Explanation: Creates the first entry in Pretranslator 1. This entry looks
for the specific sequence of digits 6111.
PreTranslatorOperation Create 1 1 1 replace 5502
Explanation: Creates the first operation associated with PreTranslator 1,
PreTranslatorEntry 1. Defines a replace operation that replaces all digits in
the incoming sequence (6111) with 5502. In this example, 5502 connects
you to the Auto Attendant menu for customer service.
PreTranslatorEntry Create 1 2 6
Explanation: Creates, the second entry in Pretranslator 1; this entry
looks for any incoming digit string beginning with the number 6.
PreTranslatorOperation Create 1 2 1 stripLead 1
Explanation: Creates the first operation associated with PreTranslator 1,
PreTranslatorEntry 2. Defines a stripLead operation that removes (strips)
the first (leading) digit from the incoming 4-digit sequence. This removes
the 6 from the incoming numbers (6000 through 6199) leaving 3-digit
numbers from 000 through 199.
PreTranslatorOperation Create 1 1 2 prepend 3
Explanation: Creates the second operation associated with PreTranslator 1,
PreTranslatorEntry 2. Defines a prepend operation that adds the digit 3 at
the beginning of the 3-digit string (created by the previous operation). The
incoming numbers from 000 through 199 become numbers from 3000
through 3199.
The Incoming dial plan table may already contain this line. If necessary,
modify the line to match.
TableEntry Create 2 4 3 4 4 Internal 0 0
Explanation: In table ID 2 (Incoming dial plan table) entry 4 instructs the
system to look for 3 as the first in a sequence of 4 digits (both Min and
Max are 4). If the system finds such a sequence, it assigns Internal as the
Sample Solutions Using Dial Plan Configuration File Commands
327
call class. The system does not use the number in the priority column,
so it remains 0 (zero). The system directs the call to route 0 (zero),
the default route for internal extensions.
Customer Requirement 4. Assume that the company is located in
New York, and has two long distance telephone carriers: ABC, which
provides a low-cost service to four Boston area codes (508, 617, 781, and
978), and DEF, which provides service to the rest of the United States. You
want to use one 4-port Analog Line Card, connected to analog trunk
lines owned by ABC, for all calls to the Boston area. You want to use the
T1 line, which you lease from DEF, for all other long distance calls within
the United States.
The system users dial 9 to get an outside line, 1 to obtain a long distance
carrier, 3 digits to specify the area code, and 7 digits to specify the
telephone number. To ensure that long distance calls are managed in the
least-cost way that you want, you place these entries in the Internal dial
plan table. The numbering of the entries assumes that the table has 46
entries before you make any additions. Columns in each table entry are
titled: Command, Table Number, Entry Number, Digits, Min, Max, Class,
Priority, and Route Number.
Add these lines to the dial plan configuration file:
TableEntry Create 1 47 91 12 12 LongDistance 0 2
Explanation: Creates, in table ID 1 (the Internal table), entry 47, which
directs the system to look for the digits 91 at the beginning of any
12-digit sequence (Min and Max are both 12). If the system detects such
a sequence, it assigns LongDistance as the class of service.
Because the system software does not use the priority value, the system
leaves 0 (zero) as the value, and assigns the call to route 2 (the T1 route).
Dial plan entries are searched in sequential order. As soon as dialed digits
match a dial plan entry, the dial plan acts on that match without further
analysis. So if a previous dial plan entry (entries 1 through 46 in this
example) was matched, entry 47 would not be found or used.
TableEntry Create 1 48 91508 12 12 LongDistance 0 1
Explanation: In table ID 1 (the Internal table), creates entry 48, which
directs the system to look for the digits 91508 at the beginning of any
12-digit sequence (Min and Max are both 12). If the system detects such a
sequence, it assigns LongDistance as the class of service. Because the system
328
CHAPTER 11: DIAL PLAN
software does not use the priority value, the system leaves 0 (zero) as the
value, and assigns the call to route 1 (the route that uses the 4-port card).
TableEntry Create 1 49 91617 12 12 LongDistance 0 1
Explanation: In table ID 1 (the Internal table), creates entry 49, which
directs the system to look for the digits 91617 at the beginning of any
12-digit sequence (Min and Max are both 12). If the system detects such
a sequence, it assigns LongDistance as the class of service. Because the
system software does not use the priority value, the system leaves 0 (zero)
as the value, and assigns the call to route 1 (the route that uses the 4-port
card).
TableEntry Create 1 50 91781 12 12 LongDistance 0 1
Explanation: In table ID 1 (the Internal table), creates entry 50, which
directs the system to look for the digits 91781 at the beginning of any
12-digit sequence (Min and Max are both 12). If the system detects such
a sequence, it assigns LongDistance as the class of service. Because the
system software does not use the priority value, the system leaves 0 (zero)
as the value, and assigns the call to route 1 (the route that uses the 4-port
card).
TableEntry Create 1 51 91978 7 7 LongDistance 0 1
Explanation: In table ID 1 (the Internal table), creates entry 51, which
directs the system to look for the digits 91978 at the beginning of any
12-digit sequence (Min and Max are both 12). If the system detects such
a sequence, it assigns LongDistance as the class of service. Because the
system software does not use the priority value, the system leaves 0 (zero)
as the value, and assigns the call to route 1 (the route that uses the 4-port
card).
In combination, the five lines in the internal table work with these two
lines in the Routes section of the dial plan.
DestinationRoute Create 1 Boston Low-cost Carrier
DestinationRoute Create 2 T1 Line to DEF Telephone Company
Explanation: Creates two routes, numbered 1 and 2, with the names
“Boston Low-cost Carrier” and “T1 Line to DEF Telephone Company.”
DestinationRouteEntry Create 1 1 *0001
DestinationRouteEntry Create 2 1 *0001
Explanation: In route 1, creates entry number 1, which defines
extension list *0001 (line card port extensions) as the destination. Then
creates, in route 2, an entry that defines extension list *0002 (Digital Line
Card extensions) as the destination.
Sample Solutions Using Dial Plan Configuration File Commands
329
DestinationRouteOperation Create 1 1 1 stripLead 1
DestinationRouteOperation Create 2 1 1 stripLead 1
Explanation: Creates, in route 1, entry 1, operation number 1. This is a
stripLead operation, which removes the first digit from the dialed string,
then and passes the remaining digits to the carrier.
Customer Requirement 5. Assume that you want to transmit CLIP
information about outgoing calls. You use internal telephone extension
numbers from 3000 to 3099. There is no DDI/DID, so the T1 or E1 line has
only a single number (555-555-1212). All incoming calls are routed by
default to the Auto Attendant.
Add these lines to the dial plan configuration file:
PreTranslator Create 1 CLIP Internal Ext to Single Number
Explanation: Create pretranslator table 1 called “CLIP Internal Ext to
Single Number.”
PreTranslatorEntry Create 1 1 3
Explanation: For pretranslator 1, create entry 1, which applies when the
first digit in the sequence is 3. (All internal telephone extensions begin
with the number 3.)
PreTranslatorOperation Create 1 1 1 replace 555 555 1212
Explanation: For pretranslator 1, entry 1, create operation 1, which
replaces the extension number with the string 555 555 1212.
Customer Requirement 6. Assume that you want to use two different
long distance carriers at different times of the day, to obtain a cost saving.
To select one long distance carrier from 7:30 a.m.) to 3:00 p.m., prepend
1010321 to each call. To select another carrier and obtain a lower rate
from 3:00 p.m. until opening business hours the next day, prepend
1010220. This assumes the business is not open on weekends.
Add these lines to the dial plan configuration file:
TableEntry Create 1 99 91 12 12 LongDistance 0 27
Explanation: In Table 1 (Internal table) entry 99, creates an entry which
looks for the digits 91 at the beginning of any 12-digit sequence (because
both Min and Max are set to 12). If the system detects such a sequence, it
assigns LongDistance as the class of service.
Because system software does not use the priority value, the system
leaves 0 (zero) as the value, and assigns the call to route 27.
330
CHAPTER 11: DIAL PLAN
If Table 1 already contains an entry with 91 in the digits column, delete
it and substitute the above TableEntry Create line.
TimedRoute Create 27 28 3PM Switchover
Explanation: Create TimedRoute 27, with a default DestinationRoute
of 28. Assign the title “3PM Switchover” to TimedRoute 27.
TimedRouteEntry Create 27 1 7:30 15:00 .MTWTF. 29
Explanation: For TimedRoute 27, create entry 1, which applies from
7:30 a.m. through 3:00 p.m. Monday through Friday. The route to use is 29.
DestinationRouteCreate 29 Open Hours Carrier
Explanation: Create DestinationRoute 29, and call it “Open Hours
Carrier.”
DestinationRouteEntry Create 29 1 *0002
Explanation: For DestinationRoute 29, create entry 1, which uses
extension list *0002, the extension list that contains all extensions
associated with Digital Line Cards.
DestinationRouteOperation Create 29 1 1 stripLead 2
Explanation: For DestinationRoute 29, entry 1, create operation 1,
which strips 2 digits (9 and 1) from the beginning of the dialed string.
DestinationRouteOperation Create 29 1 2 prepend 1010321
Explanation: For DestinationRoute 29, entry 1, create operation 2,
which prepends 1010321 to select the long distance carrier to use from
7:30 a.m. Monday through Friday.
DestinationRoute Create 28 Carrier After 3pm and Closed
Explanation: Create DestinationRoute 28 and call it “Carrier After
3 p.m. and Closed.”
DestinationRouteEntry Create 28 1 *0002
Explanation: For DestinationRoute 28, create entry 1, which uses
extension list *0002, the extension list that contains all extensions
associated with Digital Line Cards.
DestinationRouteOperation Create 28 1 1 stripLead 2
Explanation: For DestinationRoute 28, entry 1, create operation 1,
which strips 2 digits (9 and 1) from the beginning of the dialed string.
DestinationRouteOperation Create 28 1 2 prepend 1010220
Explanation: For DestinationRoute 28, entry 1, create operation 2,
which prepends 1010220 to select the other long distance carrier.
Sample Solutions Using Dial Plan Configuration File Commands
331
Route 28 is the default route, so it is used at all other times than those
defined for route 29.
Example 1 If you make a long distance call at 2:00 p.m. on any Tuesday,
the system uses these timed route definitions, and:
■
Verifies that the date is a valid business date.
■
Verifies that the time is prior to 3:00 p.m.
■
Selects timed route 29.
■
Prepends 1010321 to the outgoing call to select the first long distance
carrier.
Example 2 If you make a long distance call at any time on any Saturday,
the system uses these timed route definitions, and:
■
Verifies that the date is not a valid business date.
■
Selects timed route 28.
■
Prepends 1010220 to the outgoing call to select the second long
distance carrier.
332
CHAPTER 11: DIAL PLAN
12
VIRTUAL CONNECTIONS
This chapter describes these elements of the system:
■
Overview of Virtual Tie Lines
■
TAPI Route Points
■
TAPI Settings
For more information about these topics and configuration procedures,
see the online Help.
Overview of
Virtual Tie Lines
A Virtual Tie Line (VTL) provides a way to make calls between system sites
that are separated geographically but are tied together by a Wide Area
Network (WAN). VTLs are a licensed feature of the systems. V3000,
V3001, V3001R, and V5000 systems can support up to 48 simultaneous
VTL connections. NBX 100 systems can support up to 8 simultaneous VTL
connections.
On any system, you can use a VTL connection either for an incoming VTL
call from any site or for an outgoing VTL call to any site. A VTL connection
is not dedicated in the same way as a physical tie line, which always
connects the same pair of sites. In the example in Figure 20, you can use
the VTLs on the Chicago system for any combination of incoming and
outgoing VTL calls to either Atlanta or Dallas.
The system can reroute VTL calls that fail to reach their destination on the
first attempt. For details, see “Call Rerouting for Virtual Tie Lines” on
page 346.
■
Virtual tie line (VTL) connections between NBX systems must run
software versions that are no more than one version apart. For
example, a system that is running R6.x system software is VTL
compatible with a system that is running R5.0 software, but VTL
334
CHAPTER 12: VIRTUAL CONNECTIONS
connections between an R6.x system and an R4.3 system are not fully
compatible.
■
You must configure the system for either IP On-the-Fly or Standard IP
to use VTL connections to other systems.
■
VTL connections are not available on a SIP-mode system.
■
VTL connections cannot be configured to run through firewalls or NAT
routers.
■
When you calculate the number of devices on a system, do not
include the number of VTLs.
There are two implementation techniques you can use: unique extension
ranges (see the next section) or site codes (see page 335).
VTL Connections
Using Unique
Extension Ranges
If you can restrict the extension ranges on each of the systems so that
they do not overlap, you can configure the dial plans to route calls based
only on the extension that is being dialed. The caller does not have to dial
any digits to specify the site.
Assess your growth plans for each site to verify that as you add
telephones you do not exceed your defined extension ranges.
Figure 20 depicts a configuration that uses unique extension ranges.
Figure 20 Multi-site Network using Virtual Tie Lines
Chicago
System
Extensions
1000 – 1999
WAN
Dallas
System
Extensions
3000 – 3999
Atlanta
System
Extensions
2000 – 2999
Overview of Virtual Tie Lines
335
In the sample network shown in Figure 20, each site is set up to use a
unique range of telephone extensions. The dial plan on each of the
systems is configured so that whenever a call is made to an extension not
located at the local site, the system sets up a VTL connection to the
appropriate site.
To make a call to a user in Dallas, a user in Chicago dials a Dallas
extension (3000 through 3999). The dial plan on the Chicago system is
configured to set up the necessary VTL connection to the Dallas system,
and then to the extension at that site.
See “Dial Plan Configuration” on page 339 for more information about
how to set up VTLs in the dial plan.
VTL Connections
Using Site Codes
The simpler way to implement VTL connections uses a site code, which
consists of one or more digits that a user must dial to specify the site that
is being called. This approach requires no restriction on the telephone
extension ranges, but does require the caller to dial the site code digits as
well as the extension.
A site code can be any number of digits, but typically, one- or two-digit
numbers make the most sense. The dial plan at each site must include
appropriate routing instructions for each of the possible site code.
Figure 21 shows three sites connected by VTLs. All sites use the same
range of extension numbers (1000 through 3999). To reach someone on
another system, a user must dial a site code (61, 62, or 63 in this
example) followed by an extension.
336
CHAPTER 12: VIRTUAL CONNECTIONS
Figure 21 Virtual Tie Lines Using Site Codes
Chicago
System
Extensions
1000 – 3999
Site Code 61
WAN
Atlanta
System
Extensions
1000 – 3999
Site Code 62
Dallas
System
Extensions
1000–3999
Site Code 63
To call someone in Atlanta, a user in Chicago must dial the site code 62
and then the appropriate extension (1000 through 3999). To reach a user
in Dallas, a user in Chicago must dial 63 and then the appropriate
extension (1000 through 3999). Because the extension is preceded by the
site code, there is no conflict between the extension dialed and an
identical extension number at the local site (Chicago). The choice of site
codes is made by the person who configures the dial plans for the sites.
See “Dial Plan Configuration” on page 339 for more information about
how to set up VTLs in the dial plan.
Conference Calls
Using VTL
Connections
Users can set up conference calls over VTLs in much the same way that
they set up conference calls with other users at their local site, or at a site
reachable by an external telephone line.
■
On V3000, V3001, V3001R, or V5000 systems, you can have up to
twelve 4-person conference calls simultaneously.
■
On NBX 100 systems, you can have up to four 4-person conference
calls simultaneously.
To make conference calls between sites, you must implement IGMP
(Internet Group Management Protocol) on your network.
Overview of Virtual Tie Lines
337
Conference Calls Using Site-Unique Extensions
In Figure 20, a user in Chicago establishes a conference call with two
users in Atlanta and one user in Dallas as follows:
1 Dial the first extension in Atlanta.
2 After the user answers, press Conference and dial the second extension
in Atlanta.
3 When the second user answers, press Conference again to connect all
three users.
4 Press Conference again and dial the extension of the user in Dallas.
5 When the fourth party answers, press Conference to connect all four
users.
Conference Calls Using Site Codes
In Figure 21, if you work in the Chicago office, to establish a conference
call with two people in Atlanta and one person in Dallas:
1 Dial the site code (62) and the first extension.
2 After the first user answers, press Conference, dial the same site code
(62) and the second extension in Atlanta.
3 When the second Atlanta user answers, press Conference again to
connect all three users.
4 Press Conference again and dial the Dallas site code (63) and then the
extension of the user in Dallas.
5 When the Dallas user answers, press Conference again to connect all
four users.
Conference Calls Involving Site Codes and Off-Site Telephones
In Figure 21, you work in the Chicago office and want to establish a
conference call with someone in Atlanta, someone in Dallas, and
someone at an external telephone number, you:
1 Dial the Atlanta site code (62) and then the extension.
2 After the Atlanta user answers, press Conference and dial the Dallas site
code (63) and then the extension.
3 When the Dallas user answers, press Conference again to connect all
three users.
4 Press Conference again and dial the external telephone number.
338
CHAPTER 12: VIRTUAL CONNECTIONS
If the site requires that you dial 9 to reach an outside telephone line, and
if the call is a long-distance call, the user may dial a number in area code
367 using the digit sequence 913675551212.
5 When the person answers, press Conference again to connect all four
users.
How to Configure a
Virtual Tie Line
Configuring a working VTL connection between two systems involves:
■
License Installation
■
Dial Plan Configuration
■
Updating the Extension List
■
Adding VTL Devices to the Pretranslators (Optional)
■
Verification of the Virtual Tie Line
You can enable silence suppression and different levels of audio
compression for your VTL calls. For more information about how silence
suppression and compression affect bandwidth, see “Audio Settings” on
page 34. To change the system-wide settings for silence suppression and
compression on VTL calls, use the NBX NetSet utility to edit the audio
settings (click System-Wide Settings > Audio Settings).
License Installation
You must obtain and install a license to enable VTLs.
Each VTL license applies only to the system on which it is installed. For
example, to connect three sites by VTLs and to have each site support up
to 8 simultaneous active VTL connections, install a separate license key
for 8 VTLs on each of the three systems.
To increase the number of VTLs above one of the levels on a system, add
one or more incremental licenses of 2 VTLs each.
To install a VTL license:
1 Click Licensing and Upgrades > Licenses > Add License.
2 In the field, type the license key code.
3 Click OK and then restart the system.
How to Configure a Virtual Tie Line
Dial Plan
Configuration
339
You configure the dial plan after you install the VTL license. See “License
Installation” on page 338 for information about VTL licenses.
To configure the dial plan for VTLs, you must define:
■
Routes within the dial plan
■
Digit sequences to be used to select those routes
■
Operations to be performed for each route
Example: Dial Plan with Site-Unique Extensions
In Figure 20, each of the three sites uses a unique extension range. In the
Internal table in the Chicago system dial plan, the entries shown in
Figure 22 control the routing of calls if a user dials an extension in the
2000 through 2999 range (Atlanta extensions) or the 3000 through 3999
range (Dallas extensions) respectively. The dial plans for the Atlanta and
Dallas systems would contain similar, but not identical entries.
An explanation of each line in the dial plan follows Figure 22.
340
CHAPTER 12: VIRTUAL CONNECTIONS
Figure 22 Sample Dial Plan Entries for Chicago Using Site-Unique Extensions
Table Create 1 Internal 4 Digit Extensions
/
Id Entry Digits
Min Max Class
/
-- ----- ----------- --- --- ------------TableEntry Create
1
3 2
4
4 WAN
TableEntry Create
1
4 3
4
4 WAN
Prio Route
---- ----0
522
0
523
/
Route Description
/
----- ----------DestinationRoute Create
522 Atlanta VTL Connection
DestinationRoute Create
523 Dallas VTL Connection
/
Route Entry DestinationExtension
/
----- ----- -------------------DestinationRouteEntry Create
522
1 *0006
DestinationRouteEntry Create
523
1 *0006
/
Route Entry OperId Operation
/
----- ----- ------ --------DestinationRouteOperation Create
522
1
1 prepend
DestinationRouteOperation Create
523
1
1 prepend
Value
----192*168*25*100*
192*168*35*100*
The first TableEntry Create command modifies entry 3 in Table 1. Entry 3
watches for 4-digit sequences (Min = 4, Max = 4) beginning with 2
(extensions 2000 through 2999) and specifies route 522 whenever a
4-digit sequence falls within this range. Entry 4 watches for 4-digit
sequences (Min = 4, Max = 4) beginning with 3 (extension 3000 through
3999) and specifies route 523 whenever a 4-digit sequence falls within
this range. Route numbers 522 and 523 are examples only. The choice of
route numbers is made by the person who configures the dial plans for
the sites.
Two DestinationRoute Create commands create routes 522 and 523. The
Description field contains any text you want to use to describe each
route.
Two DestinationRouteEntry Create commands specify the extension list
for routes 522 and 523. Extension list *0006 is reserved for VTLs.
How to Configure a Virtual Tie Line
341
Two DestinationRouteOperation Create commands prepend the IP
Address of the destination system to the extension that the user dialed. In
this example, the IP address for Atlanta is 192.168.25.100 and for Dallas,
the IP address is 192.168.35.100. You must use the asterisk (*) character
to separate fields within the IP address and to separate the IP address
from the destination extension.
Example: Dial Plan with Site Codes
In Figure 21, each of the three sites uses the same extension range. In the
Internal table in the Chicago system dial plan, the entries shown in
Figure 23 select route 522 and 523 if a user dials the site codes 62 and 63
respectively, and then dials an extension. The dial plans for the Atlanta
and Dallas systems would contain similar, but not identical entries.
An explanation of each line in the dial plan follows Figure 23.
Figure 23 Sample Dial Plan Entries for Chicago Using Site Codes
Table Create 1 Internal 4 Digit Extensions
/
Id Entry Digits
Min
/
-- ----- ----------- --TableEntry Create
1
100 62
6
TableEntry Create
1
101 63
6
Max
--6
6
Class
------------WAN
WAN
Prio Route
---- ----0
522
0
523
/
Route Description
/
----- ----------DestinationRoute Create
522 Atlanta VTL Connection
DestinationRoute Create
523 Dallas VTL Connection
/
Route Entry DestinationExtension
/
----- ----- -------------------DestinationRouteEntry Create
522
1 *0006
DestinationRouteEntry Create
523
1 *0006
/
Route Entry OperId Operation
/
----- ----- ------ --------DestinationRouteOperation Create
522
1
1 stripLead
DestinationRouteOperation Create
522
1
2 prepend
Value
----2
192*168*25*100*
342
CHAPTER 12: VIRTUAL CONNECTIONS
The first TableEntry Create command creates entry 100 in Table 1. This
assumes that the highest previous entry in Table 1 was 99 or lower. Entry
100 watches for the 2-digit sequence 62 followed by a 4-digit extension
and specifies route 522 whenever a user dials such a 6-digit (Min = 6 and
Max = 6) sequence. Entry 101 watches for the 2-digit sequence 63
followed by a 4-digit extension and specifies route 523 whenever a user
dials such a 6-digit sequence. The choice of route numbers is made by the
person configuring the dial plans for the sites.
Two DestinationRoute Create commands create routes 522 and 523. The
Description field contains any text you want to use to describe each
route.
Two DestinationRouteEntry Create commands specify the extension list
for routes 522 and 523. Extension list *0006 is the default extension list
for VTLs.
For each DestinationRoute, two DestinationRouteOperation Create
commands perform two functions:
Updating the
Extension List
■
The stripLead command removes the two digits (62 or 63) leaving the
4-digit extension the user dialed.
■
The prepend command adds the IP Address of the destination system
to the extension that the user dialed. In this example, the IP address
for Atlanta is 192.168.25.100 and for Dallas, the IP address is
192.168.35.100. In the dial plan, you must use an asterisk (*) instead
of a period (.) to separate the fields within the IP address, and to
separate the IP address from the destination extension.
The final step to activate the virtual tie lines is to add the VTL extensions
to the appropriate extension list (*0006).
To update the extension list:
1 Log on to NetSet using the administrator login ID and password.
2 Click Dial Plan > Extension Lists.
3 Click *0006, which is the Virtual Tie Lines extension list.
The system displays the Modify window, which includes a membership
list. The membership list can list the members already added to the VTL
extension list, or a full listing of extensions if the extension list has no
members.
How to Configure a Virtual Tie Line
343
4 To add an extension to the list:
c If the list does not include any members, click the check boxes next
the extension of the VTL that you want to add to the list.
d If the list already has members, click Show all to display a list of
extensions that you can add to the list’s membership.
Note: You can toggle between the Show all and Show members only
buttons to display extensions that have membership in the extension list
and the extensions that are not members of the list but which you can
add to the list, and to confirm your changes.
The system displays (VTL) and the name of the virtual tie line in the Device
Description field. The number of VTL extensions depends on the VTL
license installed on this system. Table 61 describes the VTL extension
ranges.
o
Table 61 Virtual Tie Line Extension Ranges
Adding VTL Devices
to the Pretranslators
(Optional)
Platform
Extension Range
V3000 and V3001
4-digit dial plan
6500–6523
V3000 and V3001
3-digit dial plan
The default dial plan for a V3000 or V3001 system is 4-digit.
If you convert to a 3-digit dial plan, you must manually
change each 4-digit extension to a 3-digit extension. For
VTLs, you can select any unused 3-digit extension from the
external extension range (600–799).
If you add a VTL pretranslator to the dial plan to reformat the information
of incoming VTL calls, you must add the VTL devices to that pretranslator.
You can add a pretranslator to the dial plan to format caller ID and CDR
records for VTL calls. See “Creating a Pretranslator for VTL Calls” on
page 301.
To add the VTL devices to the pretranslator:
1 Log on to NetSet using the administrator login ID and password.
2 Click Dial Plan > Pretranslators.
3 Click the VTL pretranslator.
4 In the Devices Using window, click the check boxes next to the devices
associated with VTLs. For a 4-digit dial plan, the VTL device extensions
range from 6500 through 6523. For a 3-digit dial plan, VTL device
extensions range from 623 through 630.The device descriptions include
(VTL).
344
CHAPTER 12: VIRTUAL CONNECTIONS
5 Click OK.
Verification of the
Virtual Tie Line
After you have configured the VTLs on each of two systems, verify that
the VTL connection works properly.
To verify that a working VTL connection exists between two systems, you
must verify:
■
Local System Verification — Verify that the configured VTLs appear on
each system.
■
Remote Access Verification — Verify that each of the systems can
access each other.
■
Placing Telephone Calls — Verify that telephone users can make calls
can between all pairs of connected systems in both directions.
Local System Verification
On each system, use the NBX NetSet utility to verify that you can view the
local VTLs:
1 Click Virtual Connections > Virtual Tie Lines.
2 Verify that the list displays the VTLs you configured.
In our example, if you perform this verification test on the Chicago
system, the results appear as shown in Figure 24.
Figure 24 Example: Virtual Tie Lines Window
How to Configure a Virtual Tie Line
345
Remote Access Verification
To verify that each system can access the other, on each system:
1 Click Virtual Connections > Virtual Tie Lines.
2 Click the Query Remote tab.
3 In the Query Remote window, type the IP address of the remote system in
the IP address field and click Query.
If the verification is successful, the window displays the VTLs configured
at the remote site.
Example: You have installed an system in Chicago, Atlanta, and Dallas,
and you have configured two VTL connections on each of the Chicago
and Atlanta systems. The IP addresses of the three systems are:
■
Chicago — 192.168.15.100
■
Atlanta — 192.168.25.100
■
Dallas — 192.168.35.100
The Atlanta system (IP address 192.168.25.100) shows two installed but
idle VTL connections. If you execute the Query Remote operation from
the Atlanta office and specify the IP address of the Chicago system, the
local system displays two installed but idle VTL connections.
If the local system fails to access the remote system, it displays an error
message.
If you have not yet configured the remote system to support VTLs, this
message indicates that you must do so before the Query Remote
operation can succeed.
If you have configured the remote system to support VTLs, the error
message indicates that the local system cannot access the remote system
using the IP address you specified. To correct the problem:
1 Verify that you specified the correct IP address for the remote system.
2 Verify that the remote system is running properly.
3 Verify that the remote system is using the dial plan which you modified to
configure VTLs on that system.
4 Work with your network administrator to verify that WAN connection
between the two sites is properly configured and is working.
5 Verify that the VTL extensions are included in the Devices Using
Pretranslator table.
346
CHAPTER 12: VIRTUAL CONNECTIONS
Placing Telephone Calls
The final step to verify a virtual tie line connection is to place telephone
calls in both directions between each pair of connected sites.
Call Rerouting for
Virtual Tie Lines
To enable the system to better deal with network problems, you can
configure the system dial plan so that some virtual tie line (VTL) calls can
be rerouted if a VTL connection cannot be made.
VTL calls can be rerouted if:
■
The dial plan contains an invalid IP address
■
The remote system is not responding
■
All VTL channels on the remote system are currently busy
■
All IP addresses in the IP On-the-Fly address pool are in use
Some VTL calls are not rerouted. Example situations in which a call is not
rerouted include:
■
Placing a VTL call to another system with the intention of hopping off
(dialing a telephone number local to the other system) when all trunks
are busy on the other system
■
Dialing an invalid telephone number
If you normally connect calls from site A to site B using VTL connections,
you can define an alternate route to site B using Analog Line Card ports,
Digital Line Card channels, and the like. If a network problem such as a
router failure occurs, or if all VTL ports on the site A system are busy, VTL
calls that fail to reach site B are then dialed using the alternate route.
If your VTL call is rerouted, you see additional routing information in the
display panel on your telephone.
The system log file contains records of failed VTL calls that were rerouted.
Example Dial Plan
Entries
If you normally dial a site code such as 72 to reach site B, and if the
telephones at the other site use four-digit extensions, the dial plan entries
to manage the initial call and the rerouting of the call may look like the
example shown in Figure 25.
Call Rerouting for Virtual Tie Lines
347
Figure 25 Sample Dial Plan Entries for Rerouting VTL Calls
Table Create 1 Internal 4 Digit Extensions
/
Id Entry Digits
Min Max Class
/
-- ------ ------------ --- --- ------------TableEntry Create
1
8 72
6
6 WAN
Prio Route
---- ----0
6
/
Routes
/
Route Description
/
----- ----------DestinationRoute Create
6 Site B
/
Route Entry DestinationExtension
/
----- ----- -------------------DestinationRouteEntry Create
6
1 *0006
DestinationRouteEntry Create
6
2 *0001
/
/
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
Create
Create
Create
Create
Route Entry OperId Operation
----- ----- ------- --------6
1
1 stripLead
6
1
2 prepend
6
2
1 stripLead
6
2
2 prepend
Value
----2
192*168*155*100*
2
1978247
Explanation:
The TableEntry Create command specifies that when a user on the local
system dials a six-digit number beginning with the digits 72, the call is
routed through route 6, which is the route that normally contains only
the VTL extension list (*0006).
To allow VTL calls to be rerouted, route 6 is configured to use both the
VTL extension list and the Line Cards extension list (*0001). Calls that use
route 6 can be completed using devices in either of these extension lists.
There are four DestinationRouteOperation lines. The first two lines specify
the primary way to manage the call, using VTL methods. The last two
lines specify the backup way to manage the call if the first method fails.
348
CHAPTER 12: VIRTUAL CONNECTIONS
Successful VTL Call
If there are no network problems:
1 The first line (Entry 1, OperId 1) removes the digits 72.
2 The second line (Entry 1, OperId 2) prepends the IP address of the system
at site B in front of the dialed extension number.
Unsuccessful VTL Call
If a network problem or a lack of VTL ports prevents the VTL call from
reaching its destination:
1 The third line (Entry 2, OperId 1) removes the digits 72.
2 The fourth line (Entry 2, OperId 2) prepends an appropriate dial string and
dials out over an analog telephone line.
Managing Existing
Virtual Tie Lines
Modifying a Virtual
Tie Line Name
After VTLs are installed and you have verified that they are working
properly, you can manage them using the NBX NetSet utility. There are
NetSet utility functions for:
■
Modifying a Virtual Tie Line Name
■
Viewing and Resetting Virtual Tie Line Statistics
■
Enabling Audio Compression for VTL Calls
■
Enabling Silence Suppression on VTL Calls
You can change the name of a VTL. The name appears in NetSet lists, and
helps you identify each VTL.
To modify the name of a VTL:
1 Click Virtual Connections > Virtual Tie Lines, which displays the list of
existing VTLs, and the status of each one.
2 Select a VTL from the list, which displays the Modify window.
3 In the New VTL name field, type the name you want to assign to this VTL.
4 Click OK and verify the name change is in the Virtual Tie Lines window.
Viewing and
Resetting Virtual Tie
Line Statistics
You can view the statistics for a VTL at any time.
Managing Existing Virtual Tie Lines
349
To view statistics for a VTL:
1 Click Virtual Connections > Virtual Tie Lines.
2 Click the Statistics tab, which displays the Statistics window and the
information described in Table 62.
3 To reset all VTL statistics, click Reset.
If you restart the system, it resets all VTL statistics.
Table 62 Virtual Tie Line Statistics Fields
Field
Description
NOTE: All statistics apply to the time period since the most recent Reset command
or since the most recent system reboot, whichever was more recent. To define the
starting time for the displayed statistics, compare the Last reset command with the
time of the Last system reboot. Both are displayed at the bottom of the VTL Statistics
window.
Number of outgoing
VTL calls made
The number of outgoing calls made over all virtual tie lines
(VTLs) since the most recent reset command or since the time
the system was last restarted. Each time you restart the
system, you reset the statistics for all VTLs.
Number of incoming
VTL calls received
The number of incoming calls received over all VTLs since the
most recent reset command or since the time the system was
last restarted.
Number of active VTL The number of calls currently active on all VTLs.
calls
Maximum number of The maximum number of VTL calls that have been active at
concurrently active
the same time on this system since the most recent reset
VTL calls
command or since the time the system was last restarted.
Enabling Audio
Compression for VTL
Calls
Incoming VTL calls
rejected due to all
VTLs busy
The number of telephone calls that would have arrived from
other systems over VTL channels, but could not be accepted
because all local VTL ports were busy when the calls arrived.
Outgoing VTL calls
rejected due to all
VTLs busy
The number of telephone calls that would have been sent
from the local system over VTL channels, but could not be
sent because all local VTL ports were busy when the calls
were made.
Rerouted VTL calls
The number of calls that did not reach their destination
when attempted over VTL channels, and were rerouted using
another device.
Last reset command
The date and time of the most recent Reset for this VTL.
Last system reboot
The date and time of the most recent reboot of the system.
You can set audio compression for VTL calls. The default condition is no
audio compression because compression can compromise audio quality.
350
CHAPTER 12: VIRTUAL CONNECTIONS
For more information about how compression affects bandwidth, see
“Audio Settings” on page 34.
During VTL call setup, the VTL software at each end of the call negotiates
a compression level that is supported by both systems. For example,
System A is configured for G729, high compression, and System B is
configured for G711, no compression. A VTL call between System A and
System B will use G711, no compression. It does not matter which system
initiates the call.
To enable VTL audio compression:
1 Click System-Wide Settings > Audio Settings.
2 Click the Audio Compression on VTL Calls check box and then click OK.
Enabling Silence
Suppression on VTL
Calls
You can enable silence suppression for VTL calls. The default condition is
disabled because silence suppression can compromise audio quality. For
more information about how compression affects bandwidth, see “Audio
Settings” on page 34.
When you enable VTL silence suppression, the VTL software attempts to
use silence suppression on all VTL calls. If the other system is not
configured to support silence suppression, the local VTL software
attempts to find a compatible communications mode.
Do not enable silence suppression unless you have network congestion
problems you cannot solve otherwise. Enabling silence suppression can
reduce network traffic, but the result is a compromise to audio quality.
To enable silence suppression on VTLs:
1 Click System-Wide Settings > Audio Settings.
2 Under VTL Audio Calls Settings, enable the Enable Silence Suppression
check box.
3 Click OK.
Using a VTL
Password
To allow users on one system to place VTL calls to another system and
then place long-distance (toll) calls from that location (a practice called
‘hop off’), you can configure a VTL password.
When an system receives a VTL call from a user on another system, it can
allow that user to make long-distance calls if the incoming VTL call
Using a VTL Password
351
contains the password. Otherwise, such calls are not allowed. If you set
up two classes of VTL calls (with and without passwords), you can permit
or deny hop off.
To enable a system to manage incoming hop off calls, create or modify a
VTL password, as described in the next topic, Configuring a VTL
Password.
To enable a system to send hop off VTL calls, configure the dial plan to
include the VTL password, as described in Configuring VTL Passwords in
the Dial Plan on page 351.
Configuring a VTL
Password
For each system that can receive VTL calls, use the NBX NetSet utility to
configure a local system VTL password.
To configure the password:
1 Click System Maintenance > Password Administration.
2 Select Virtual Tie Lines Password in the Password list, and then click Go.
3 Type the administrator password in the Current Admin Password field.
4 Type the new VTL password in the New Virtual Tie Lines Password field.
Passwords are from 8 to 15 characters in length and must contain only
letters and numbers. Upper and lower case letters are permitted.
5 Retype the new VTL password in the Re-enter New Password field.
6 Click OK.
Configuring VTL
Passwords in the
Dial Plan
For each remote system that controls hop-off by means of a VTL
password, configure that password into the VTL commands in the local
dial plan.
If you use site codes to access other systems through VTL connections,
you can configure one set of VTL connections that permit hop-off and are
accessed by one set of site codes. You can configure another set of VTL
connections that do not permit hop-off and are accessed using a different
set of site codes.
If you use unique extension ranges at each site, and therefore do not dial
a site code when placing VTL calls to users at those sites, you can still use
codes to access VTL connections that permit hop-off at the far end.
352
CHAPTER 12: VIRTUAL CONNECTIONS
Figure 26 shows how to configure VTL passwords in a dial plan, using site
codes that permit hop-off and other site codes that do not.
Figure 26 Dial Plan Entries for VTL Passwords
Table Create 1 Internal 4 Digit Extensions
/
Id Entry Digits
Min
/
-- ----- ----------- --TableEntry Create
1
100 62
6
TableEntry Create
1
101 63
6
TableEntry Create
1
102 72
6
TableEntry Create
1
103 73
6
/
/
DestinationRoute
DestinationRoute
DestinationRoute
DestinationRoute
Create
Create
Create
Create
/
/
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
Route
----522
523
524
525
Create
Create
Create
Create
/
/
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
Max
--6
6
32
32
Class
------------WAN
WAN
WAN
WAN
Prio Route
---- ----0
522
0
523
0
524
0
525
Description
----------Atlanta VTL Connection
Dallas VTL Connection
Atlanta VTL Connection with password
Dallas VTL Connection with password
Route Entry DestinationExtension
----- ----- -------------------522
1 *0006
523
1 *0006
524
1 *0006
525
1 *0006
Create
Create
Create
Create
Create
Create
Create
Create
Route Entry OperId Operation Value
----- ----- ------ --------- ----522
1
1 stripLead 2
522
1
2 prepend
192*168*25*100*
523
1
1 stripLead 2
523
1
2 prepend
192*168*35*100*
524
1
1 stripLead 2
524
1
2 prepend192*168*25*100*ATLPassW*
525
1
1 stripLead 2
525
1
2 prepend 92*168*35*100*DALPWord*
The first TableEntry Create command creates entry 100 in Table 1. This
assumes that the highest previous entry in Table 1 was 99 or lower. Entry
Using a VTL Password
353
100 watches for the 2-digit sequence 62 followed by a 4-digit extension
and specifies route 522 whenever a user dials such a 6-digit (Min = 6 and
Max = 6) sequence. Entry 101 watches for the 2-digit sequence 63
followed by a 4-digit extension and specifies route 523 whenever a user
dials such a 6-digit sequence. The choice of route numbers is made by the
person configuring the dial plans for the sites.
The next two TableEntry Create commands are set up in a similar manner
to manage VTL connections with passwords. If a user dials 72 followed by
a 4-digit extension, the VTL call uses route 524. If a user dials 73 followed
by a 4-digit extension, the VTL call uses route 525. These two commands
specify a minimum of 6 digits (for example, if the caller is calling an
internal extension preceded by the site code) and a maximum of 32 digits
(for example if the caller is calling a long-distance or international number
preceded by the site code).
The first two DestinationRoute Create commands create routes 522 and
523. The Description field contains text that describes each route.
The second two DestinationRoute Create commands create routes 524
and 525, the routes that are used with a VTL password.
The four DestinationRouteEntry Create commands specify the extension
list for routes 522, 523, 524, and 525. Extension list *0006 is the default
extension list for VTLs.
For the first two DestinationRoutes, two DestinationRouteOperation
Create commands perform two functions:
■
The stripLead command removes the two digits (62 or 63) leaving the
4-digit extension the user dialed.
■
The prepend command adds the IP Address of the destination system
to the extension that the user dialed. In Figure 26, the IP address for
Atlanta is 192.168.25.100; for Dallas, 192.168.35.100. In the dial
plan, use an asterisk (*) instead of a period (.) to separate the fields
within the IP address, and to separate the IP address from the
destination extension.
For the second two DestinationRoutes, two DestinationRouteOperation
Create commands perform two similar functions.
■
The stripLead command removes the two digits (72 or 73) leaving the
4-digit extension the user dialed.
354
CHAPTER 12: VIRTUAL CONNECTIONS
■
The prepend command adds the IP address and system password of
the destination system to the extension dialed by a user. In Figure 26,
the IP address for Atlanta is 192.168.25.100 and the password is
ATLPassW. For Dallas, the IP address is 192.168.35.100 and the
password is DALPWord. In the dial plan, you use an asterisk (*) instead
of a period (.) to separate fields within the IP address and to separate
the IP address from the destination extension.
To place a hop-off call to 555-1212 in area code 903 through the Atlanta
system, a user on a remote system would dial 72919035551212. The 72
code sets up a VTL connection to Atlanta that incudes the Atlanta
system’s VTL password, and the remaining digits are used to dial the
number (9 accesses an outside line to obtain dial tone from the local
carrier, 1 accesses the long-distance carrier, and the remaining digits
specify the long-distance number).
If the same user used site code 62 to place a call to the Atlanta office,
only toll-free, emergency, and internal call would be allowed.
Toll Calls Without a
VTL Password
If a local user has configured his telephone to forward calls to a
long-distance number, then an incoming VTL call to that telephone does
not need to supply the local system’s VTL password in order for the call to
be forwarded.
Music On Hold
If two users are talking on a VTL connection, and the first user places the
call on hold, the second user hears Music On Hold only if his local system
is configured to play it.
Troubleshooting VTL
Calls
Table 63 contains a list of error situations, the possible causes and the
action to take in each case.
Table 63 VTL Errors and Corrections
Error Condition
Possible Causes
Long pause after dialing. Telephone display contains Remote server does not
“VTL” during the pause. Busy signal is then heard. respond
Actions
Test the connection to the
remote system using the
Query Remote function.
Using a VTL Password
355
Table 63 VTL Errors and Corrections (continued)
Error Condition
Possible Causes
Actions
After you dial a VTL call, there is a busy signal and
the telephone display panel displays the “All ports
busy” message.
1. No VTL license installed.
1. Verify that the licenses
appear when you access the
tab.
2. VTL device extensions not
added to Extension List
*0006.
3. All local VTL connections
are currently in use.
4. All VTL connections at the
remote site are currently in
use.
2. Verify that the *0006
extension contains the VTL
device extensions.
3. On the Virtual Tie Line tab,
verify that there is at least one
idle VTL connection.
4. Use the Query Remote
function to verify that there is
at least one idle VTL
connection.
After you dial a VTL call, there is a busy signal and
the telephone display panel displays the “Invalid
Number” message.
1. Local dial plan is not
properly configured.
No audio
1. Telephones are not
configured to use either IP
On-the-Fly or Standard IP.
2. Dial plan on the remote
2. Examine the dial plan on
(target) system in not properly the remote system for errors.
configured.
3.Verify that the password for
3. You are trying to use
the remote system is used in
hop-off without the necessary both dial plans.
password.
2. VTL Audio compression is
supported on only one of the
two systems.
3. 3C10165D E1 and
3C10116D T1 Digital Line
Cards do not have static IP
addresses.
Caller ID information does not display correctly in
the telephone display panel.
1. Examine the local dial plan
for errors.
1. Invalid local pretranslator.
1. Verify that the IP setting in
the System Settings,
System-Wide dialog box is “IP
On-the-Fly” or “Standard IP.”
Change the setting, if
necessary.
2. Verify that audio
compression is enabled on
both systems.
3. If your system is set up for
IP On-the-Fly, verify that
3C10165D E1 and 3C10116D
T1 Digital Line Cards have a
static P address. These cards
cannot receive an IP
On-the-Fly address.
1. Examine the local dial plan
for pretranslator errors.
2. VTL extensions are not in
the VTL pretranslator “Devices 2. Verify that VTL extensions
Using” table.
appear in the left-hand table
for the pretranslator.
356
CHAPTER 12: VIRTUAL CONNECTIONS
TAPI Route Points
A TAPI Route Point is a virtual device within the system where calls are
held pending action by an external TAPI application. Route points are
typically used by call center applications to redirect calls. A redirected call
is one that is sent from its original destination (the route point) without
being answered, to a new location specified in the external application.
A TAPI Route Point in the system is an extension with a voice mailbox in
the normal extension range:
■
V3000, V3001, V3001R, V5000 systems: 1000 – 3999
■
NBX 100 systems: 100 – 449
You create the TAPI Route Point, configure the system to route calls to it,
and then configure the external application to monitor it. For example,
you can configure a line card port to send all incoming calls on that line
to a specific TAPI Route Point. When a call arrives at the route point
extension, it is queued until the external application examines it and then
instructs the Call Processor to redirect the call to a destination specified in
the external application. Typically, the redirect action is based on the caller
ID information of the incoming call.
Redirect Behaviors
Table 64 describes the behavior of TAPI Route Points and redirected calls
within the system.
Table 64 TAPI Route Points and System Features
Call Redirected to
Description
Internal extension
If the internal extension has activated Do Not Disturb, a call
redirected to that extension goes immediately to the
extension’s Call Forwarding setting.
If the TAPI Line Redirect Timeout is set to a value greater
than the extension’s Call Forwarding setting and the call is
not answered, the redirected call will be managed by the
extension’s Call Forwarding setting. The system will log a
successful redirect. If the TAPI Line Redirect Timeout is set
to a value less than the extension’s Call Forwarding setting
and the call is not answered, the call will return to the
route point. For more information, see “Specifying TAPI
Line Redirect Timeout” on page 359.
TAPI Route Points
357
Table 64 TAPI Route Points and System Features (continued)
Call Redirected to
Description
External number
Subject to the route point extension’s Class of Service
setting.
The call connects as soon as the external line resource (line
card port, a PRI line, or a T1 channel) is acquired. The caller
hears the call progress tones directly from the CO. At this
point, the system logs a successful connection. Calls
redirected to an external number cannot timeout, even if
the call was redirected to a busy or an invalid number.
Call Park extension
If a call has been previously parked at the specified Call
Park extension, the redirected call is connected to the
parked call.
If no call is waiting at the specified Call Park extension, the
call returns to its original destination when the TAPI Line
Redirect Timeout expires and the external application can
redirect it again. After two failures, the call goes to the Call
Coverage specified for the Route Point.
Hunt Group extension
Calls redirected to a Hunt Group extension do not timeout.
Once the call is passed to the Hunt Group, the system
reports that the call has been successfully redirected.
Calls can be redirected from a Hunt Group extension.
You cannot add a TAPI Route Point extension to a Hunt
Group.
Hunt Group member
A Hunt Group takes precedence over a Route Point. If a call
arrives on a Hunt Group member telephone because it is a
member of a Hunt Group, a redirect is not permitted. If a
call arrives on the phone’s extension (not as a result of a
Hunt Group action), the call can be redirected.
Phantom Mailbox
A call can be redirected to a phantom mailbox.
Mapped Line
Calls that arrive through an incoming line that is mapped
to a line appearance button on a telephone cannot be
redirected.
If you redirect a call to a mapped line, the call does not
timeout. It fails and is routed back to the route group until
the caller disconnects.
Bridged Station
Appearance
Calls can be redirected to or from a telephone that has a
bridged station appearance. Once a call to a primary
bridged station appearance reaches the secondary bridge
station appearance, the call cannot be redirected.
Configurable Operator Calls can be redirected to a System Operator or a Personal
Operator.
358
CHAPTER 12: VIRTUAL CONNECTIONS
TAPI Route Point
Capacities
When the maximum number of calls on a route point is reached (see
Table 65), subsequent calls routed into the route point from an internal
extension or through a Virtual Tie Line ring for 10 seconds and are then
disconnected. If the call arrives through a line card port, the call continues
ringing.
Table 65 TAPI Route Point Capacities
System
Maximum Number Maximum Number of Calls for
of Route Points
Each Route Point
NBX 100
48
400
V3000, V3001,
V3001R, and V5000
100
400
NOTE: A 3-digit dial plan may not provide enough extensions to support 100 TAPI
Route Points.
Creating a
TAPI Route Point
To create a new TAPI Route Point, the system administrator performs
these steps:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Virtual Connections > TAPI Route Points.
3 Click Add to open the Add TAPI Route Point window.
4 Enter the appropriate information in the fields.
5 See the see the online Help for more information.
Modifying a
TAPI Route Point
To modify a TAPI Route Point:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Virtual Connections > TAPI Route Points.
3 From the list of TAPI Route Points, select the one you want to modify to
open the Modify window.
4 See the see the online Help for more information.
To modify the password for the TAPI Route Point, enter the administrator
password for the system in the Current Admin Password field.
TAPI Route Points
Viewing TAPI Route
Point Statistics
359
You can view the statistics for all of the TAPI Route Points on this system.
The system starts to accumulate new statistics each time you reboot the
system or each time you click the Reset button in the TAPI Route Point
Statistics dialog box.
To view TAPI Route Point statistics:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Virtual Connections > TAPI Route Points tab.
3 Click the Statistics button.
4 Click the heading of any column to sort the data in ascending or
descending order.
5 Click Reset to erase all data. The system begins collecting new statistical
data.
The Last reset command field displays the date and time of the most
recent Reset. A row of hyphens (---------------) indicates no Reset since the
most recent system reboot.
The Last system reboot field contains the date and time when the system
was most recently rebooted.
See the online Help for information about dialog box fields.
Specifying TAPI Line
Redirect Timeout
The TAPI Line Redirect Timeout is a system-wide timer that specifies the
amount of time before a redirected call goes back to its original
destination, which allows the TAPI application to redirect the call again.
When a redirected call times out, the system also sends a failure code
back to the TAPI application. After two failures, the call goes to the route
point’s call coverage option.
To set the TAPI Line Redirect Timeout:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System-Wide Settings > Timers.
3 See the online Help for the procedure to set timers.
TAPI Supervisory
Monitoring
You can configure the system to allow a privileged user to join an
ongoing conversation with or without the knowledge of the parties
360
CHAPTER 12: VIRTUAL CONNECTIONS
involved in that conversation. This feature is called Supervisory
Monitoring.
The monitoring user is called the supervisor. The supervisor, who may or
may not be the system administrator, can join a call between a person
calling into the system (for example, a customer) and a person on-site
whose job it is to accept incoming calls. Joining calls in progress can
ensure proper customer support.
The system allows Supervisory Monitoring on outgoing calls as long as
the agent is in the domain that corresponds to the password that the
supervisor uses to monitor the agent.
To use Supervisory Monitoring, the supervisor needs:
■
The Route point extension
■
The Supervisory Monitoring Domain password
■
The agent’s telephone extension
To set or change the Supervisory Monitoring password, you need first to
provide the system administrator password. The System Administrator
configures Supervisory Monitoring parameters using the Supervisory
Monitoring window of the NBX NetSet utility.
Supervisory Monitoring uses IP Multicast. Because the system has a global
pool of multicast addresses that Supervisory Monitoring and other
features use, it is possible for the system to exhaust its pool of multicast
addresses and thus return an error to a monitoring request.
Supervisory
Monitoring Modes
As a supervisor, you can employ Supervisory Monitoring in any of the
following modes to monitor incoming calls:
■
Monitor
Allows you to join a call in progress without an alert that is audible by
either the agent or the customer.
Monitor mode requires a password. To start monitoring a call, the
supervisor must use one of the following:
■
Feature code 425
■
Mapped button
■
Display panel Soft Key (not available on all phones) that the
administrator has configured for this purpose.
TAPI Settings
■
361
Whisper
Allows you to join a call in progress to speak with the agent without
alerting the customer to your presence. Whisper mode requires a
password.
■
Barge-In
Allows you to join a call in progress to speak with both the agent and
the customer. Barge-In mode requires a password.
Either the agent or the supervisor can put the call on hold while
Supervisory Monitoring is in effect. This means that the supervisor can
initiate two monitoring sessions: one active session and one on hold.
TAPI Settings
You must configure system-wide Telephony Application Programming
Interface (TAPI) settings before users can download the NBX TAPI Service
Provider (NBXTSP). NBXTSP enables a TAPI application on a user’s PC to
interact with the user’s 3Com telephone. You can set a maximum number
of TAPI clients in the system. You can also require users to enter
passwords for TAPI devices.
Before you configure system-wide TAPI settings, install the appropriate
TAPI software. After you have the software installed, select Virtual
Connections > TAPI Settings to configure TAPI settings. See the online
Help for procedures to configure TAPI settings and download NBX TSP
software.
The TAPI settings do not apply to TAPI Route Points. For security reasons,
the system always requires that an external application supply a password
to access a TAPI Route Point.
362
CHAPTER 12: VIRTUAL CONNECTIONS
13
DOWNLOADS
This chapter provides information about downloading:
■
Software
■
LabelMaker Utility
■
Documentation and Reference Guides
For more information about these topics and configuration procedures,
see the online Help.
Software
You can download and install the following software applications on a
computer that runs the Microsoft Windows 2000, Windows XP, or
Windows Vista operating system:
■
NBX Call Reports — Enables you to retrieve call logging information
from the system for reporting purposes.
■
NBX TAPI Service Provider (NBX TSP) — Enables you to use
TAPI-enabled programs with the system.
■
3Com Telephone Local Configuration Application (TLC) —
Devices with a display panel use the Local User Interface (LUI) to
define the settings that the device needs to communicate with the
Call Processor. For telephones that do not have a display panel, such
as the 3Com 3100 Entry Telephone, use the Telephone Local
Configuration (TLC) application to define these settings. See
Chapter 18 for more information about how to configure devices.
To download these applications, click Downloads > Applications and see
the online Help for more information.
LabelMaker Utility
Each 3Com Telephone and Attendant Console comes with a set of blank
labels on which users and administrators can write Speed Dials and other
364
CHAPTER 13: DOWNLOADS
unique settings that have been applied to the buttons. If you are setting
up many telephones with similar features, you can use the LabelMaker
utility to create and print your labels.
Both telephone users and administrators can download and run the
LabelMaker utility to create labels for all 3Com telephones and Attendant
Consoles.
The LabelMaker utility is a Windows program file. If you use an operating
system that cannot run Windows programs, contact your 3Com NBX
Voice-Authorized Partner for a PDF version of the LabelMaker.
To download and run the LabelMaker utility:
1 Log in to the NBX NetSet utility using the administrator username and
password.
2 Click Downloads > LabelMakers > Universal LabelMaker.
You can also log in as a telephone user and click Resources > Telephone
Button Labels to launch the LabelMaker utility.
3 See the online help for more information about how to create and print
labels.
Documentation and
Reference Guides
You can view and download Adobe PDF versions of the following guides:
■
NBX Installation Guide
■
This administrator’s guide
■
Telephone guides for 3Com telephones
■
NBX Feature Codes Guide for Analog Telephones
■
NBX Feature Codes Guide for SIP Telephones
■
IP Messaging Module Installation Guide
To view and print the documentation, click Downloads > Documentation.
Telephone users can click Resources and then the appropriate tabs to
view and print quick reference guides, telephone guides, and the feature
codes guide.
You can get or upgrade your existing version of Adobe Acrobat Reader
from the Adobe web site, www.adobe.com.
14
LICENSING AND UPGRADES
This chapter describes how to manage licensing and upgrade operations
for your system. It describes:
■
Licenses
■
Software Upgrade
■
Third-Party Drivers
For more information about these topics and configuration procedures,
see the online Help.
Licenses
You can install licenses on your system for these components:
■
System software
■
pcXset™ (Soft Telephone) application
■
Voice mail (Additional voice mail and Auto Attendant ports and voice
mail storage)
■
Disk mirroring (V5000 and V3001R systems only)
■
Devices (specifies the total number of devices allowed on the system)
■
Windows Audio Volume (WAV) devices
■
Virtual Tie Lines (VTLs)
■
Internet Voice Messaging (VPIM)
■
Third-Party Messaging
■
Complement Attendant Software
■
Call Recording & Monitoring
■
Polycom Telephones
■
Legacy Link Nortel, Meridian, and Analog Telephones
■
Groups 0 – 4 Devices
366
CHAPTER 14: LICENSING AND UPGRADES
■
Automatic Call Distribution (ACD)
See the NBX Installation Guide for a complete list of licenses and system
capacities.
To manage your software licenses:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
2 Click Licensing and Upgrades > Licenses.
3 See the online Help for procedures to manage licenses.
Add a License
Each system includes a factory default license associated with the system
serial number.
■
On V3000, V3001, and V3001R systems, the serial number is on the
front of the chassis.
■
On V5000 systems, the serial number is on the disk tray.
■
On NBX 100 systems, the serial number is on the Call Processor
backplane.
To configure the system to support new licenses, contact your 3Com NBX
Voice-Authorized Partner and provide the serial number. The dealer
obtains a new license key from 3Com Customer Support that enables the
upgrade.
See the online Help for procedures to add a license to a system.
Remove a License
The only license that you can remove from a system is the disk mirroring
license, which enables a V5000 or V3001R system to use two disks in a
mirrored configuration.
CAUTION: See “Reverting to a Single-Disk System” on page 90 for
instructions how to remove the disk mirroring license. If you do not
follow the procedure correctly, you may not be able to restart the system.
The system displays the Remove License button on V5000 or V3001R
systems only.
Licenses
Usage Report
Backing Up Licenses
367
For each license installed on the system, the Usage Report displays the
current number of devices in use for the license type and the maximum
number of devices allowed by that license.
3Com recommends that you make a backup copy of all licenses on your
system.
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Licensing and Upgrades > Licenses.
3 Click Backup.
4 Click Save, choose a location to save the backup file, and click Save again.
You can also back up licenses if you click System Maintenance > System
Backup and enable the Include NBX Licenses check box.
Restoring Backed-Up
Licenses
You can restore all licenses from a previously created backup file.
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Licensing and Upgrades > Licenses.
3 Click the Restore Licenses tab.
4 Type the full path to the license backup file in the Enter path to restore
license(s) on this system: field or browse to the location in which you
saved the licenses backup file.
5 Click Restore and respond to the confirmation prompt message that
appears.
NOTE: After you restore the licenses, you must restart the system.
Therefore, 3Com recommends that you restore licenses only during
nonbusiness hours.
Obtaining Details of
License History
You can view a detailed history, including the date and time on which
each license was added to the system.
368
CHAPTER 14: LICENSING AND UPGRADES
To view the license detail report, click Licensing and Upgrades > Licenses
> License Details.
Software Upgrade
As part of the upgrade and reboot process, you can choose to use your
existing configuration data with the new version of the software or use a
new (empty) database. the NBX NetSet utility allows you to choose which
software version to use when you reboot the system. This allows you to
restore an earlier operating environment (both software and
configuration data), if necessary.
To upgrade or remove software:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click System Maintenance > System Software Upgrade.
3 See the online Help for procedures to upgrade or remove software.
Software Upgrade Notes
Release 4.2 introduced system software licensing. Be sure to review the
information in the next topic, System Software Licensing, before you
upgrade your system software.
■
See the Software Upgrade Procedure, which is available on the NBX
Resource Pack DVD or from www.3com.com, for information about
how to upgrade a specific release of software.
■
To run system software release R4.2 and higher, you must install a
license key.
■
A license key is required only for upgrading to major releases, RX.X.
All minor releases, RX.X.X, use the corresponding major release license
key.
■
To upgrade a system to release R4.3 first upgrade to release R4.2.
■
To upgrade a system to release R4.2 first upgrade to release R4.1.
■
A 4.3 license is valid for both a 4.1-to-4.2 upgrade as well as the
4.2-to-4.3 upgrade.
■
When you upgrade the system software, do not enter any “cd...”
commands using the terminal-emulation software on a PC attached to
the Call Processor.
Software Upgrade
System Software
Licensing
369
■
When the software upgrade is complete, a window that contains a
confirmation message displays in the NBX NetSet utility.
■
Before you upgrade your system software, 3Com recommends that
you back up your system data. (See “System Backup” on page 73.)
■
If you are using PC applications, such as the pcXset application, you
must also upgrade these applications after upgrading the software.
■
If you are using the NBX Call Reports application, install the latest
version of the application from the NBX Resource Pack DVD or the
NBX Partner Access web site.
■
If you are connected to the Call Processor COM1 port, you see the
upgrade activity messages during the upgrade process, but you
cannot issue any commands.
■
After you upgrade your system software, reboot the system.
To run release R4.2 and all later releases of the V3000 or V3001 system
software on your system, you must have and install a license. A license
key is required only for upgrading to major releases, RX.X. All minor
releases, RX.X.X, use the corresponding major release license key. All
systems that are shipped from the factory with software release R4.2 or
any later release, include a license for the software version that is shipped
with the system.
Upgrading to R4.2 From a Previous Release
To upgrade a system to release R4.2 first upgrade to release R4.1.
Upgrading From R4.1.14 and Prior Releases
If your system software is release R4.1.14 or a previous release, you
cannot enter the license key for R4.2 before you upgrade because the
system software will not recognize the R4.2 license as valid.
Use these steps to upgrade to R4.2:
1 Upgrade to R4.2 in the usual way.
2 Reboot to R4.2.
3 When you see the warning message that indicates you must install a
license, click the License button and install the R4.2 license.
If you decide not to install the R4.2 license key, you can click the Reboot
button and select a different release.
370
CHAPTER 14: LICENSING AND UPGRADES
Upgrading From R4.1.15 and Later Versions
If you are running R4.1.15 or a later release of R4.1, you can enter the
R4.2 license key and then upgrade. When you enter the license key, the
system software accepts the license key as valid for an unknown feature.
When you upgrade and reboot to R4.2, the license for R4.2 takes effect.
Upgrading From Release 4.2
If you are running R4.2 and you upgrade to a new software version, the
final step is to reboot the system specifying the new release. At that time,
the software verifies that you have the proper license installed. If you
have installed the license prior to the reboot, the upgrade is completed.
If you have not installed the correct license prior to the reboot phase of
the upgrade, the system provides a warning message and guidance on
the appropriate action for you to take.
Restricted Operation
If you reboot the system without installing the required license, the
system remains operational with these restrictions:
■
the NBX NetSet utility is not available.
■
Each telephone display panel periodically displays a NO LICENSE
message.
■
Auto discovery is turned off for all device types.
■
Voice mail messages are not allowed.
■
The Automated Attendant software is not operational.
■
The ability to configure user groups and Automated Attendants from
a telephone is not operational.
■
If you use a terminal-emulation software application, such as
Hyperterm, to connect a PC to the system COM1 port, the system
sends a message to the Hyperterm application to indicate that a
required software license has not been installed.
If you log on using the administrator ID and password, a window appears
giving you two options:
■
You can click the Reboot button to go to a reboot window and reboot
to a previous software release.
■
You can click the License button to go to a license window and enter a
license key for R4.2.
Software Upgrade
371
The installation of a valid upgrade license removes all restrictions without
the need for a system reboot operation.
Considerations
Some situations require specific actions because of the system software
licensing mechanism.
Chassis or Disk Tray Replacement
If you have an NBX 100, V3000, or V3001 system and you need to
replace the main system chassis for any reason, provide a valid license
backup file to your 3Com NBX Voice-Authorized Partner. This file enables
them to provide you with license keys equivalent to those that were
associated with the replaced chassis.
If you have a V3001R or V5000 system and you need to replace the
system disk tray for any reason, provide a valid license backup file to your
3Com NBX Voice-Authorized Partner. This file enables them to provide
you with license keys equivalent to those that were associated with the
replaced disk tray.
Licenses for Future Releases
If you purchase a license for a future software release, all software
releases up to that version are included. For example, if you purchase a
license for release R6.0 and you are currently running release R5.0, you
can upgrade to any release R5.X release without the need to purchase an
additional license.
Downgrading to Previous Releases
If you are running R4.2 with a valid system software license and you want
to downgrade to a previous, unlicensed software version (for example,
R4.0 or R4.1) you can do so by rebooting to the previous version. No
other action is required.
Customer Service
If you reboot to R4.2 without installing a valid license, and you run your
system with the restrictions in place (see “Restricted Operation” on
page 370), 3Com Customer Service cannot access the information
required to help you with problems. To obtain assistance from 3Com
Customer Service, either reboot to a previous version of the system
software or install a license for R4.2.
372
CHAPTER 14: LICENSING AND UPGRADES
Third-Party Drivers
You can add and configure third-party telephones for use on a system.
The third-party vendor supplies the interface hardware and a software
package to support the telephones.
The process of adding third-party telephones includes these steps:
■
Install the device type license — Each third-party device type
(typically a telephone) must be licensed for use on the system. The
license governs the type of device and the number of devices of that
type that can be added to the system.
■
Installing the software driver — This step places the third-party
driver software on the system disk.
■
Importing the software driver — This step activates the third-party
driver software.
See the online Help for more information about these procedures.
To remove a third-party driver, you must either purge the system
database, or revert to a previous database in which the third-party driver
was not installed.
Software Upgrades
When you upgrade the system software, you do not need to reinstall and
import the third-party drivers, provided that you continue to use the same
system database after the upgrade.
If you upgrade the system software and choose to start with a new
database, or if you revert to a database that did not include the
third-party driver, import the third-party driver again.
Third-Party
Telephone Groups
When you install and import a third-party driver, the system creates a new
telephone group for the third-party telephone type. When you add
third-party telephones to the system, by default the system adds them to
this group.
You cannot delete the default third-party telephone group.
A third-party telephone can belong to the default third-party telephone
group, or to a telephone group that you create for that third-party
telephone.
15
REPORTS
This chapter describes how to access details of system data traffic. It
describes these topics:
■
Directory
■
Device List
■
System Data
For more information about these topics and configuration procedures,
see the online Help.
Directory
The system provides a directory listing of all the telephone extensions in
the system (except for special use extensions such as TAPI Route Point
extensions).
If the Auto Attendant picks up a call, the caller can use the telephone’s
key pad to type the first letters of a person's last name to search this
directory. The Last Name parameter of each user profile forms the
dial-by-name directory.
The directory includes only mailboxes that have been initialized and have
a recorded greeting. The directory does not include special purpose
mailboxes, such as a mailbox associated with a TAPI Route Point. You can
exclude a user from the directory when you add or modify a user.
To view, print, or search the system directory, click Reports > Directory
and see the online Help for more information.
Device List
The system provides a list of the devices and functions that are currently
being used, such as telephones, line card ports, voice mail ports, Call Park
extensions, and Groups.
374
CHAPTER 15: REPORTS
To view or print a report of system devices, click Reports > Device List and
see the online Help for more information.
System Data
The system provides basic data about the system.
Before you contact your 3Com Voice - Authorized Partner or 3Com
Technical Support, access this report and record the information.
To view system data, click Reports > System Data and see the online Help
for more information.
V3001R and V5000 systems support disk mirroring and dual power
supplies. If your system is configured with disk mirroring or dual power
supplies, the System Data window includes a Disk Status button and a
Power Supply Status button.
Disk Status
In addition to viewing basic system data, you can also view data
specifically about disk drives. If your system is configured for disk
mirroring, you can confirm the status of both disks.
To view disk status, click Reports > System Data > Disk Status and see the
online Help for more information.
Power Supply Status
If your system is configured with two power supplies, the Power Supply
Status report provides the status of each power supply.
To view power supply status, click Reports > System Data > Power Supply
Status and see the online Help for more information.
For each power supply, the report displays these types of information:
Table 66 Power Status Report Information
Field
Purpose
Connected
The connection status for each power supply.
Values: True or False
Output voltage
The output voltage status.
Values: Valid or Invalid
16
NETWORK MANAGEMENT
This chapter provides information about the tools that you can use to
manage the network:
■
SNMP
■
Syslog
■
Periodic Timestamp on Console (PTOC)
■
Event Logging
■
Maintenance Alerts
For more information about these topics and configuration procedures,
see the online Help.
SNMP
Simple Network Management Protocol (SNMP) is a transport protocol
used for network management on IP networks, including remote fault
notification and performance monitoring.
SNMP sends messages, called Protocol Data Units (PDUs), between SNMP
managers and SNMP agents. Agents store data about themselves in
Management Information Bases (MIBs) and return this data to SNMP
managers. System users with special rights can be SNMP users and
retrieve this data.
You use the NBX NetSet utility to enable and disable SNMP, configure
authorized SNMP managers, configure users, and define security.
SNMP topics include:
■
SNMP Managers and Agents
■
SNMP Security
■
Special Considerations
376
CHAPTER 16: NETWORK MANAGEMENT
■
MIBs and MIB Objects
SNMP Managers and Agents
Terminology and
Acronyms
377
These terms and acronyms are commonly used to describe SNMP
operations.
Table 67 SNMP Terminology and Acronyms
SNMP Managers
and Agents
Item
Detail
Authentication
Process of ensuring data origin authenticity, specifically that
the identity of the user is genuine. Also incorporates data
integrity checks, to ensure data has not been altered or
destroyed in an unauthorized manner.
CBC
Cipher-Block-Chaining (a method of encoding data
encryptions in a message).
HMAC
Keyed-Hash Message Authentication Code. Provides message
authentication through the use of cryptographic hash
functions.
Inform
Reliable notification of an SNMPv3 event.
Key
A value that is used to ensure authenticity or privacy, without
which it is almost impossible to masquerade or eavesdrop.
MD5
Message Digest type 5 (a type of hashing function).
Notification
SNMPv3 event.
Privacy
The hiding of data from eavesdroppers.
SHA
Secure Hashing Function (a type of hashing function).
Trap
SNMPv1 message notifying the manager of a system event.
USM
User-based Security Model.
VACM
View-based Access Control Model.
MIB
Management Information Base.
An agent using network elements stores network information about itself
in a Management Information Base (MIB). MIBs specify the variables that
network elements maintain. For example, a variable can contain the data
that records when you last booted the system.
SNMP managers are network hosts that use SNMP software to poll the
network devices and receive the information stored in them.
■
Managers use UDP port 161 by default to send requests to the agent
■
Agents use UDP port 162 by default to send replies or messages to the
manager.
378
CHAPTER 16: NETWORK MANAGEMENT
The manager can request data from the agent, or can set variable values
in the agent. Agents can reply to the manager’s requests, and can also
report events.
SNMP collects information two ways:
■
SNMP management stations poll the devices on the network.
■
Devices send alerts to SNMP management stations.
SNMP has successive iterations as its operations have become more
secure. These iteration, in order of greater security, are SNMPv1, SNMPv2,
and SNMPv3. The system supports these three modes.
SNMP Security
The system supports these two security models:
■
Community Strings — Pre-SNMPv3 standard compatibility
■
User-based Security Model (USM) — SNMPv3
The View-based Access Control Model (VACM) applies to both security
models.
3Com recommends that you use SNMPv3 because of its enhanced
security features.
Community Strings
■
Community Strings
■
User-based Security Model (USM)
■
View-based Access Control Model (SNMPv1, SNMPv2c and SNMPv3)
■
Traps, Notifications, and Informs
Community strings is the method by which SNMPv1 manages its own
security.
An SNMP community is the group to which devices and management
stations running SNMP belong, and that defines where to send
information. SNMP identifies a community by means of a community
name.
It is possible for an SNMP device or agent to belong to more than one
SNMP community. The SNMP agent does not respond to requests from
management stations that do not belong to one of its communities.
SNMP Security
379
The SNMP default communities include Write (private) and Read (public).
User-based Security
Model (USM)
The USM of SNMPv3 provides greater security than pre-SNMPv3
configurations. USM includes the following security features:
■
Verifies that each received SNMP message has not been modified
during its transmission through the network.
■
Verifies the identity of the user on whose behalf a received SNMP
message claims to have been generated.
■
Detects received SNMP messages, which request or contain
management information, whose time of generation was not recent.
■
When necessary, protects the contents of each received SNMP
message from disclosure.
USM provides three levels of security on a per-user basis:
■
No authentication and no privacy (no encryption of data)
This option is comparable to SNMPv1 and does not provide the
additional benefits of SNMPv3.
■
Authentication provided by Message Digest 5 (MD5) or Secure Hash
Algorithm (SHA) with no encryption of data
■
Authentication with encryption of data by Data Encryption Standard
(DES)
To set an SNMP user’s level of security:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
2 Click Network Management > SNMP Settings.
3 Click a user name.
4 From the Authentication Protocol drop-down list, select the level of
security.
5 Click Apply.
View-based Access
Control Model
(SNMPv1, SNMPv2c
and SNMPv3)
The View-based Access Control Model (VACM) defines the access rights
of a group that users belong to. You can configure each group to have
access to a view of the MIB, so that users belonging to that group can
380
CHAPTER 16: NETWORK MANAGEMENT
view only that portion of the MIB. These views allow access to all MIB
objects according to the existing product access restrictions.
Login usernames are the users’ security names in this model.
The system checks the access rights for all requests against those
applicable to the user's configured access level, that is, the access group.
Two groups are supported:
■
Admin group — View available to Admin group (the highest level)
when connected by authenticated means
■
Monitor group — View available to all other groups, or available when
unauthenticated access is used
By default, you are a member of the Admin group and you set the access
rights of each user (click Network Management > SNMP Settings).
IF objects are read-only because of context only, the system may return
the existing SMIv1 error code no-such-name instead of the enhanced
read-only error status on an attempt to set them.
Traps, Notifications,
and Informs
In addition to receiving requests and sending responses to management
applications (managers), agents also can send unsolicited messages to
managers when they detect some significant event. An unsolicited
message is called a trap (SNMPv1) or a notification (SNMPv2 and
SNMPv3). The NBX SNMP agent supports both traps and notifications in
all three versions of SNMP.
An inform (confirmed notification) is a trap that the agent sends with a
request to the manager to acknowledge the receipt of the trap.
the NBX NetSet utility, where the manager IP address can be configured,
enables you to configure the target entries.
Ton configure the manager IP address:
1 Login to the NBX NetSet utility using the administrator login ID and
password.
2 Click Network Management > SNMP Settings
3 Click the SNMP Managers tab.
4 Click Add or the name of an existing manager.
Special Considerations
381
5 Edit the fields appropriately.
6 Click Apply.
Enterprise notifications use an snmpTrapOID, which consists of the 3Com
enterprise number (43), a zero, and the SNMPv1 trap number.
Special
Considerations
Note this information as you plan to use SNMP in your network:
■
The system does not back up SNMPv3 Engine ID, privacy keys, or
authentication.
If you restore keys, you may need to reinitialize them on both the
client and the server before they are usable. However, the system does
back up notification targets.
MIBs and MIB
Objects
■
You must back up SNMP as a part of your general system backup
operations.
■
The system does not display Authentication and Privacy keys.
■
You cannot use the same password for the Authentication and Privacy
keys.
■
When you enable Syslog, the system logs the results of a SNMPv1,
SNMPv2, and SNMPv3 set operation. In this case:
■
The SNMPv1 Read community string is logged. (SNMPv1).
■
The Security Name is logged (SNMPv2, SNMPv3).
■
The Set result codes are the enhanced SNMPv2/3 error codes.
■
Updates to the user passwords and keys are not logged.
This section lists the MIBs and MIB objects that the system uses as a part
of its standard operations.
■
MIBs Used on the System
■
Standard SNMPv3 MIBs
■
Other IEEE/RFC MIBs
■
3Com MIB Objects
■
Diagnostics for 3Com MIB Objects
■
Persistent Storage
382
CHAPTER 16: NETWORK MANAGEMENT
MIBs Used on the
System
■
Agent Conformance Reference
■
Network Management Applications
■
Applicable Endpoints
The system supports these public MIBs as read-only objects:
Table 68 Standard MIBS Supported by the System
RFC
Description
Notes
RFC 1155
Structure and Management
Information for TCP/IP
Networks
Fully supported.
RFC 1157
SNMP
Fully supported.
RFC 1213
MIB-II
Does not support egp and cmot
groups.
RFC 1215
Defining Traps
Does not support the 'warm-start'
trap.
RFC 1901
SNMPv2
You cannot do SNMP SET on any of
the objects by default using either V1
or V2. Read/Write access is removed
for the SNMP V1, V2 versions.
RFC 1907
SNMPv2 MIBs
Fully supported.
RFC 2571
SNMP Management
Frameworks
Fully supported.
RFC 2572
SNMP Message Processing and Fully supported.
Dispatching
RFC 2573
SNMP Applications
Fully supported.
RFC 2574
User-based Security Model for
SNMPv3
Fully supported.
RFC 2575
View-based Access Control
Model (VACM)
Context names are restricted to
monitor (read only) and admin
(read/write).
RFC 2576
Co-existence Among SNMPv1,
SNMPv2, and SNMPv3
Fully supported.
RFC 2737
Entity MIB
Only the EntPhysicalTable is
supported.
See “Standard SNMPv3 MIBs” on page 383 for more information.
The system also uses the 3Com NBX Enterprise MIB (a private MIB) to
show gateway and telephone information. To examine the 3Com private
MIB, see to “NBX Enterprise MIB” on page 477 in this guide.
MIBs and MIB Objects
Standard SNMPv3
MIBs
383
The system supports the following standard SNMPv3 MIBs. Where
applicable, you can configure SNMPv2 through these MIBs as well.
■
SNMP-FRAMEWORK-MIB
Supported: The standard Framework and Conformance MIB
■
SNMP-MPD-MIB
Supported: The standard Message Processing and Dispatch MIB and
Conformance MIB
■
SNMP-TARGET-MIB and SNMP-NOTIFICATION-MIB
Supported: The standard Target, Notification, and Conformance MIBs
Filter-related tables may impose a maximum limit of zero entries,
effectively disabling this feature. The system supports up to eight
notification targets entries.
■
SNMP-USER-BASED-SM-MIB
Supported: The standard User-based Security Model and
Conformance MIB
The default table is initialized according to the Security Posture of
minimum-secure. User table entries are instantiated and keys are
generated based on each system login user name and password in
force when the SNMPv3 software version is first upgraded.
■
SNMP-VIEW-BASED-ACM-MIB
Supported: The standard View-based Access Control Module and
Conformance MIB
This MIB is read-only and has permanent entries. The default security
configuration is initial-minimum-security-configuration.
The vacmSecurityToGroupTable contains the current mapping of
usernames to groups. One row exists for each username configured.
The vacmAccessTable contains four permanent entries (one for each
access level) and one additional entry for security access.
■
SNMP-COMMUNITY-MIB
The standard Community and Conformance MIB is not required.
Other IEEE/RFC MIBs
The NBX Enterprise MIB, which is a private MIB, provides information
about the status of the system. See Appendix F on page 375 for more
information.
384
CHAPTER 16: NETWORK MANAGEMENT
3Com MIB Objects
Information relating to the gateways and phones attached to the Call
Processor may be defined either as a private MIB or by using the 3Com
Enterprise MIB.
Call Processors, Gateways, and Telephones
MIB objects representing the following exist for the Call Processors,
gateways, and phones:
■
Device serial number Device 3C part number
■
Device HW version
■
SW version
■
Device class (i.e. telephone, ATA, line card port, BRI, T1, PRI, ATC, and
the like.)
■
IP address
■
IP mask
■
IP gateway
■
Physical address
■
Description
■
Device Name
Network Settings
MIB objects representing the following exist for the Call Processor.
■
IP On-The-Fly settings
■
QoS settings
Gateways
MIB objects representing the following must be implemented for
gateways (Analog Line Cards and Digital Line Cards):
■
Chassis in which the card is contained
■
Slot number
Digital Line Cards
MIB objects representing the following must be implemented for the
Digital Line Cards (T1 / ISDN PRI / ISDN BRI):
■
Number of channels on board
■
T1 SPAN list configuration:
MIBs and MIB Objects
■
■
■
■
MAC address
■
name ID
■
framing
■
line code
■
line length
■
timing mode
■
number of channels
■
number of channels on-line
■
number of channels off-line
ISDN PRI SPAN list configuration
■
MAC address
■
Name
■
Type
■
CO switch protocol
■
framing type
■
line code
■
line length
■
number of channels
■
number of channels on-line
■
number of channels off-line
ISDN BRI SPAN list configuration
■
MAC
■
ID
■
CO switch protocol
■
TEI manual/auto
■
TEI ID
■
number of channels
■
number of channels on-line
■
number of channels off-line
T1 channel list configuration
385
386
CHAPTER 16: NETWORK MANAGEMENT
■
Diagnostics for 3Com
MIB Objects
■
group name
■
channel name
■
span id
■
channel id
■
channel mac
■
extension, protocol
■
direction
■
start type
■
incoming digit format
■
called party digits
■
outgoing digit format
■
autoExt
ISDN channel list configuration
■
group name
■
channel name
■
span id
■
channel id
■
channel mac
■
extension
■
autoExt
Diagnostic and statistical information for the system must be made
available through MIB objects that represent the following:
Call Processor
■
Number of active calls
■
Number of Licenses used
■
Number of buffer allocation failures
■
Memory utilization
■
Disk Usage
MIBs and MIB Objects
387
Gateways (ALCs, DLCs):
■
Number of available ports
Telephones:
■
Voice quality metrics
Digital line cards (T1/ISDN PRI/ISDN BRI):
■
T1/ISDN Board status:
■
■
T1/ISDN SPAN status:
■
■
Unknown, Ready, Offline, Online, Red Alarm, Blue Alarm, Yellow
Alarm
ISDN SPAN D channel status
■
■
Unknown, Ready, Offline, Online, Red Alarm, Blue Alarm, Yellow
Alarm
Unknown, Up, Down
T1/ISDN Channel status
■
Unknown, Ready, Offline, Online, Red Alarm, Blue Alarm, Yellow
Alarm.
■
T1/ISDN Channel error count
■
T1/ISDN Channel last error code
■
Quality performance metrics (as defined in RFC 2495)
Traps and Informs
The system generates traps and Informs for the following events:
■
Call Processor coldstart
■
Call Processor Power up/down
■
Call Processor out of buffer threshold
■
Call Processor IP change
■
Power supply failure (V3001R or V5000 systems)
■
Malicious Call tagged
■
Emergency (911) call initiated
■
Voice mail ports exhausted
■
Failed logon attempt for admin or user
388
CHAPTER 16: NETWORK MANAGEMENT
■
License adds/deletes
■
License limits thresholds
■
VTL connection failure
■
Phone Online/Offline
■
Phone IP change
■
Gateway Online/Offline
■
Gateway IP change
■
Gateway all ports busy
■
Gateway Link state change
■
T1/ISDN Board status change
■
T1/ISDN SPAN status change
■
ISDN SPAN D channel status change
■
T1/ISDN Channel status change
System Reinitiation
The system must execute the following commands as a result of invoking
an SNMP set operation on the system:
■
Set NCP reboot (including a scheduled reboot)
■
Set NCP shutdown now
■
Set reboot now for each gateway
■
Set T1/ISDN channel restart now
NCP refers to the Call Processor.
Persistent Storage
Agent Conformance
Reference
All new MIB objects are stored in the system database except Privacy and
authentication passwords.
Table 69 shows the release R6.x support for functions defined in the
SNMPv3 Framework (RFC).
Table 69 SNMPv3 Agent Conformance for NBX Systems
SNMPv3 RFC
General
Recommended Release R6.0+ Support
MIBs and MIB Objects
389
Table 69 SNMPv3 Agent Conformance for NBX Systems
SNMPv3 RFC
Recommended Release R6.0+ Support
SNMPv2c Support
Yes
Yes
SNMPv3 Support
Yes
Yes
Management Framework Architecture Yes
Yes
Transport Mapping - UDP
Yes
Yes
get-bulk support
Yes
Yes
SMIv1
No
Yes
SMIv2
Yes
Yes
User-based Security Model
Yes
Yes
HMAC-MD5-96
Yes
Yes
HMAC-SHA-96
Yes
Yes
CBC-DES
Yes
Yes
Community-based Security Model
Yes
Yes
User-defined Groups
Yes
No
User-defined Views
Yes
No
Full support of Read-only Views
Yes
No
noAuthNoPriv
Yes
Yes
authNoPriv
Yes
Yes
authPriv
Yes
Yes
Unconfirmed notifications
Yes
Yes
Confirmed notifications
Yes
Yes
Target filtering
Yes
No
noAuthNoPriv
Yes
Yes
authNoPriv
Yes
Yes
authPriv
Yes
Yes
Security
Access Control
Command Responder
Notification Originator
390
CHAPTER 16: NETWORK MANAGEMENT
Table 69 SNMPv3 Agent Conformance for NBX Systems
SNMPv3 RFC
Recommended Release R6.0+ Support
CLI
Full management
Yes
No
Yes
No
SNMP-FRAMEWORK-MIB
Yes
Yes
SNMP-MPD-MIB
Yes
Yes
SNMP-TARGET-MIB
Yes
Yes
SNMP-NOTIFICATION-MIB
Yes
Yes
SNMP-USER-BASED-SM-MIB
Yes
Yes
SNMP-VIEW-BASED-ACM-MIB
Yes
Yes
SNMP-COMMUNITY-MIB
Yes
No
Web
Full management
MIBs
Network
Management
Applications
Applicable Endpoints
The NBX SNMP agent interoperates with the following SNMPv3 products:
■
3Com EMS (when available)
■
MG-Soft MIB browser 9.0 for Windows XP
■
HP Openview
Examine the list of 3Com and third-party products in Table 70 to see
which products can have information returned through representative
MIB objects.
The system provides some proxy information about telephones.
Table 70 Applicable Endpoints
PRODUCT / DEVICE
Part Number
Feature Supported?
1102A Business Phone
3C10121 or
3C10122
Yes
2102A Bus Phone (Lisbon)
3C10226A or
3C10228IRA
Yes
3Com Telephones
MIBs and MIB Objects
Table 70 Applicable Endpoints
PRODUCT / DEVICE
Part Number
Feature Supported?
2102B/PE Bus Phone 10/100
3C10226B/PE or
3C10228IRB/PE
Yes
1102B/PE Business Phone 10M
3C10281B/PE
Yes/
2101B/PE Basic Phone
3C10248B/PE
Yes
3100 Entry SL Phone
3C10399A
Yes
3101 Basic Phone
3C10401A
Yes
3101SP Basic Phone
3C10401SPKRA
Yes
3102 Business Phone
3C10402A
Yes
3102B Business Phone
3C10402B
Yes
3103 Manager Phone
3C10403A
Yes
3106C Cordless Phone
3C10406A
Yes
3107C Cordless Phone
3C10407A
Yes
1105 Attendant Console
3C10123A or
3C10124
Not Applicable
3105 Attendant Console
3C10405A
Not Applicable
1-port ATA (original -and -INT
versions)
3C10120 and
3C10120B-xx
No
1-port ATA (Wednesday 2nd-gen
ATA)
3C10400
Yes
4-port ATC (original and
intermediate versions)
3C10117 and
3C10117B-INT
No
4-port ATC (2nd-gen)
3C10117C
Yes
ALC (original line card port)
3C10114
No
ALC (Australia line card port)
3C10114-ANZ
No
ALC (2nd-gen)
3C10114C
Yes
BRI-ST Card
3C10164/A/C-ST
No
T1 Card (orig.)
3C10116/B/C
No
E1 Card (orig.)
3C10165/A/C
No
T1 Card (2nd-gen)
3C10116D
Yes
E1 Card (2nd-gen)
3C10165D
Yes
Adjuncts
Analog Adapters
Analog Line Cards
Digital Line Cards
391
392
CHAPTER 16: NETWORK MANAGEMENT
Table 70 Applicable Endpoints
PRODUCT / DEVICE
Part Number
Feature Supported?
Music On Hold Device
N/A
No
External Paging Device
N/A
No
Voice Mail Server
N/A
No
pcXset application
Software
No
WAV Driver
3C10319
Software
No
Call Processor Level Devices
PC Audio Products
3rd-Party Products
Syslog
Polycom IP3000 Speakerphone
2200-06632-001 No
Citel - Nortel Gateway-Norstar
1271-3C16N
No
Citel - Nortel Gateway -M1
1486-3C19M1
No
Citel - HDAGC
Not Defined
No
The Syslog protocol provides a transport mechanism that allows a device
to send event notification messages across an IP network to a Syslog
server that acts as an event message collector.
The system uses the standard 3Com logging mechanism to log event
messages from devices. Because the content of Syslog messages does
vary across the networking industry, the formatting and the contents of
the messages also vary.
The Syslog protocol is designed to transport these event messages only. In
all cases, there is one device that originates the message. The Syslog
process on that machine may send the message to a collector. The
collector does not send an acknowledgement of the receipt.
The contents of a message have also been at the discretion of its creator.
3Com recommends that you write the messages so that they are
informative to the person who may be reading them. It has also been
considered good practice to include a timestamp and some indication of
the sending device and the process that originated it in the messages.
■
Transport Mechanism
■
Terminology
Syslog
Transport Mechanism
■
3Com Implementation
■
Syslog Message Components
■
Syslog Security Considerations
393
Syslog uses the User Datagram Protocol (UDP) as its underlying Transport
layer mechanism. UDP port 514 is the Syslog port.
3Com recommends that the source port also be 514 to indicate that the
message is from the Syslog process of the sender. If the sender uses a
source port other than 514, 3Com recommends that subsequent
messages are from a single consistent port.
Terminology
3Com
Implementation
Be sure that you are familiar with these Syslog terms:
■
A machine that can generate a message is called a device.
■
A machine that can receive the message and forward it to another
machine is called a relay.
■
A machine that receives the message and does not relay it to any
other machines is called a collector. This has been commonly known
as a Syslog server.
■
Any device or relay is known as the sender when it sends a message.
■
Any relay or collector is known as the receiver when it receives the
message.
■
Senders send messages to relays or collectors with no knowledge of
whether it is a collector or relay.
■
Senders may be configured to send the same message to multiple
receivers.
■
Relays may send all or some of the messages that they receive to a
subsequent relay or collector. In the case where they do not forward
all of their messages, they are acting as both a collector and a relay.
■
Relays may also generate their own messages and send them on to
subsequent relays or collectors. In that case, a relay is acting as a
device.
The IP address of the Syslog server, ports, and the status of the Syslog
servers are persistent across reboots.
394
CHAPTER 16: NETWORK MANAGEMENT
By default, Syslog starts up at every reboot with only error messages
checked in as default and sends the log messages to the enabled Syslog
servers. You can implement up to three Syslog servers.
For information about how to configure Syslog, see the online Help.
Syslog Message
Components
This section describes how to format Syslog messages for transport.
The full format of a Syslog message has three discrete components:
■
PRI (Priority) Message Component
■
Header Component
■
MSG Component
The total length of the packet must be 1024 bytes or less. There is no
minimum length for the Syslog message, although it is a waste of
resources to send Syslog packets with no contents. The contents of a
message are at the discretion of its creator.
PRI (Priority) Message
Component
The PRI portion of a Syslog message must have the following
characteristics:
■
Three, four, or five characters
■
Be bound with angle brackets as the first and last characters.
The PRI portion starts with a leading less-than (<) character, followed
by a number, which is followed by a greater-than (>) character.
The less-than character is defined as the Augmented Backus-Naur
Form (ABNF) %60, and the greater-than character has an ABNF value
of %62. The number contained within these angle brackets is known
as the Priority value, and represents both the Facility and Severity, as
described in the section “Facilities Codes and Severity Message
Codes”.
The Priority value consists of one, two, or three decimal integers
(ABNF DIGITS) using values of %d48 (for 0) through %d57 (for 9).
Facilities Codes and Severity Message Codes
The Facilities codes and Severity Message codes are numerically coded
with decimal values.
Syslog Message Components
395
Some of the operating system daemons and processes have been
assigned Facilities values. Processes and daemons that have not been
explicitly assigned a Facility may use any of the local use facilities, or they
may use the user-level Facility.
Those Facilities that have been designated are shown in Table 71 along
with their numerical code values.
Table 71 Facility Codes
Code Value
Facility Code
0
kernel messages
1
user-level messages
2
mail system
3
system daemons
4
security/authorization messages
■
Various operating systems have been found to utilize Facilities
4, 10, 13 and 14 for security/authorization, audit, and alert
messages which seem to be similar.
5
messages generated internally by Syslog
6
Line printer subsystem
7
network news subsystem
8
UUCP subsystem
9
clock daemon
■
10
Various operating systems have been found to utilize both
Facilities 9 and 15 for clock (cron/at) messages.
security/authorization messages
■
Various operating systems have been found to utilize Facilities
4, 10, 13 and 14 for security/authorization, audit, and alert
messages which seem to be similar.
11
FTP daemon
12
NTP subsystem
13
log audit
■
14
Various operating systems have been found to utilize Facilities
4, 10, 13 and 14 for security/authorization, audit, and alert
messages which seem to be similar.
log alert
■
Various operating systems have been found to utilize Facilities
4, 10, 13 and 14 for security/authorization, audit, and alert
messages which seem to be similar.
396
CHAPTER 16: NETWORK MANAGEMENT
Table 71 Facility Codes
Code Value
Facility Code
15
clock daemon
■
Various operating systems have been found to utilize both
Facilities 9 and 15 for clock (cron/at) messages.
16
local use 0 (local0)
17
local use 1 (local1)
18
local use 2 (local2)
19
local use 3 (local3)
20
local use 4 (local4)
21
local use 5 (local5)
22
local use 6 (local6)
23
local use 7 (local7)
Each message Priority also has a Severity level indicator code (decimal).
These codes are described in Table 72 along with their numerical values.
Table 72 Severity Level Codes
Numerical Code
Severity
0
Emergency: system is unusable
1
Alert: action must be taken immediately
2
Critical: critical conditions
3
Error: error conditions
4
Warning: warning conditions
5
Notice: normal but significant condition
6
Informational: informational messages
7
Debug: debug-level messages
Renamed Facilities
The RFC facilities Local Use 0 through Local Use 3 are renamed as
Devices, Applications, CallP, and Interface Layers. Table 73 shows you the
system facilities renamed from their RFC counterparts.
Table 73 Renamed Facilities From RFC Facilities
Numerical Code
Renamed Facilities
RFC Facilities
16
Devices
Local use 0
Syslog Message Components
397
Table 73 Renamed Facilities From RFC Facilities
Numerical Code
Renamed Facilities
RFC Facilities
17
Applications
Local use 1
18
CallP
Local use 2
19
Interface Layers
Local use 3
System Log Handles
Table 71 and Table 72 show you the available facilities and severities. The
standard facilities are mapped to system log handles, as shown in
Table 74:
Table 74 Facilities Mapped to the System Log Handles
Log Handles
Numerical Code Facility
__TaskInit__
0
kernel messages
AccountCode
10
security/authorization messages
AIncomingDe...
0
kernel messages
ATA
16
Devices
AutoAttApp
17
Applications
AutoAttApp1
17
Applications
AutoAttApp2
17
Applications
AutoAttApp3
17
Applications
BasicSet
16
Devices
BasicSet12
16
Devices
Bitmail
2
mail system
BRIChannel
16
Devices
Call
18
CallP
CallControl
18
CallP
CallGroup
18
CallP
CDR
17
Applications
COFlash
18
CallP
ConfDrop
18
CallP
Conference
18
CallP
ConfPool
18
CallP
COSOverride
18
CallP
DBI
19
Interface Layers(DBI,DIL)
398
CHAPTER 16: NETWORK MANAGEMENT
Table 74 Facilities Mapped to the System Log Handles
Log Handles
Numerical Code Facility
DelayedAnn
18
CallP
DevManager
16
Devices
DiagCLI
18
CallP
DIL
19
Interface Layers(DBI,DIL)
Disks
0
kernel messages
Dnld
17
Applications
DssBlf
16
Devices
Elvis
16
Devices
ExternalVM
17
Applications
Factory
18
CallP
FeatureConfig
18
CallP
Forward
18
CallP
H3LinkLayer
3
system daemons
HuntGroup
16
Devices
HuntGroupLo...
16
Devices
i18n
17
Applications
IMAP
2
mail system
IntVM
2
mail system
IntVM6
2
mail system
IntVM64
2
mail system
IntVM642
2
mail system
IntVM643
2
mail system
IPPool
3
system daemons
LastNumDial
18
CallP
License
4
security/authorization
LockUnlock
4
Security/Authorization(note1)
MailStatSrvr
2
mail system
MediaServer
17
Applications
MWB1
18
CallP
MWB2
18
CallP
MWIToPhone
18
CallP
NBSetBus
16
Devices
messages(note1)
Syslog Message Components
Table 74 Facilities Mapped to the System Log Handles
Log Handles
Numerical Code Facility
NBSetBus11
16
Devices
NBSetBus13
16
Devices
nbxINetNot
3
system daemons
nbxNotMgr
3
system daemons
Notifier
3
system daemons
Notifier1
3
system daemons
Notifier5
3
system daemons
Notifier6
3
system daemons
Notifier7
3
system daemons
OrigSession
18
CallP
OrigStartup
18
CallP
OutDialT
17
Applications
OutDialT1
17
Applications
OutDialT2
17
Applications
OutDialT3
17
Applications
PageGroup
18
CallP
ParkZone
18
CallP
Performance
0
kernel messages
PickupClient
3
system daemons
PickupServer
3
system daemons
PRIChannel
16
Devices
RDC
16
Devices
Remote
16
Devices
RoutePoint
18
CallP
Router
0
kernel messages
Server
0
kernel messages
ServManager
0
kernel messages
Span
0
kernel messages
SpeedDial
18
CallP
SystemInfo
0
kernel messages
T1Board
16
Devices
T1Channel
16
Devices
TelephonyDNS
3
system daemons
399
400
CHAPTER 16: NETWORK MANAGEMENT
Table 74 Facilities Mapped to the System Log Handles
Log Handles
Numerical Code Facility
TermSession
18
CallP
TermStartup
18
CallP
Tlim
16
Devices
Transfer
18
CallP
UserPassword
4
security/authorization messages
VAILSess
17
Applications
VAILSess1
17
Applications
VAILSess2
17
Applications
VAILSess3
17
Applications
VAILSess4
17
Applications
VAILSess5
17
Applications
VAILSess6
17
Applications
VAILSess7
17
Applications
VAILSess8
17
Applications
VAppIL
17
Applications
VoiceApp
17
Applications
VoiceApp1
17
Applications
VoiceApp2
17
Applications
VoiceApp3
17
Applications
VoiceApp4
17
Applications
VoiceApp5
17
Applications
VoiceApp6
17
Applications
VoiceApp7
17
Applications
VoiceApp8
17
Applications
VoiceMail
17
Applications
VoiceMail1
17
Applications
VoiceMail2
17
Applications
VoiceMail3
17
Applications
VTL
18
CallP
VTLMerge
18
CallP
WEB
3
system daemons
YAVA
17
Applications
DBR
19
Interface Layers(DBI,DIL)
Syslog Message Components
401
Table 74 Facilities Mapped to the System Log Handles
Log Handles
Numerical Code Facility
Adminlog
13
log audit(note1)
SNMP traps
14
log alert(note1)
The current administration log messages are classified to only one facility;
that is, log.
The Priority value is calculated as follows:
1 Multiplying the Facility number by the number eight
2 Adding the numerical value of the Severity
Examples:
■
A kernel message (Facility=0) with a Severity of Emergency
(Severity=0) has a Priority value of zero (0).
■
A local use 4 message (Facility=20) with a Severity of Notice
(Severity=5) has a Priority value of 165.
In the PRI part of a Syslog message, these values would be placed
between the angle brackets as <0> and <165, respectively. The only
time a value of zero follows the less-than character is when the Priority
value is zero. Otherwise, leading zeros must not be used.
Header Component
The Header component of the Syslog message must contain the
following:
■
A timestamp
■
An indication of the hostname or IP address of the device
■
Visible (printing) characters
■
A seven-bit ASCII code set in an eight-bit field like that used in the PRI
part.
In this code set, the only allowable characters are the ABNF VCHAR
values (%d33-126) and spaces (SP value %d32).
The Header contains two fields called the TIMESTAMP and the
HOSTNAME.
402
CHAPTER 16: NETWORK MANAGEMENT
TIMESTAMP Field
The TIMESTAMP field contains the local time. The TIMESTAMP field
immediately follows the trailing > character of the PRI portion of the
Syslog packet.
Field Format The format of the TIMESTAMP field is:
Mmm: dd: hh:mm:ss
where the format is interpreted as follows:
Table 75 TIMESTAMP Field Format
Value
Description
Mmm
The English language abbreviation for the month of the
year, with the first character in uppercase and the other
two characters in lowercase.
The following are the only acceptable values:
dd
■
Jan
■
Feb
■
Mar
■
Apr
■
May
■
Jun
■
Jul
■
Aug
■
Sep
■
Oct
■
Nov
■
Dec
Day of the month. If the day of the month is less than ten, a
space character must precede the month digit.
For example, the 7th day of August would be represented
as “Aug 7", with two spaces between the “g” and the
“7”.
Syslog Message Components
403
Table 75 TIMESTAMP Field Format
Value
Description
hh:mm:ss
The local time.
hh — Hours represented in 24-hour format. Valid entries
are between 00 and 23, inclusive.
mm — Minutes represented by entries that are between 00
and 59, inclusive.
ss — Seconds represented by entries that are between 00
and 59, inclusive.
A single space character must follow the TIMESTAMP field.
HOSTNAME Field
The HOSTNAME field contains the hostname.
■
If the field does not have a hostname, then it contains the device IP
address.
■
If a device has multiple IP addresses, common practice is to use the IP
address from which the message is transmitted.
An alternate method is to configure a device to send all messages using a
single source IP address, regardless of the interface from which the
message is sent. This provides a single consistent hostname for all
messages sent from a device.
The HOSTNAME field contains only the hostname, the IPv4 address, or
the IPv6 address of the originator of the message. The preferred value is
the hostname.
A single space character must follow the TIMESTAMP field.
Restrictions Following are the limitations in populating the
HOSTNAME field.
■
The hostname cannot contain any embedded spaces.
■
The domain name must not be included in the HOSTNAME field.
■
If the IPv4 address is used, it must be shown as the dotted decimal
notation.
■
If an IPv6 address is used, any valid representation used in RFC 2373
may be used.
■
A single space character must follow the HOSTNAME field.
404
CHAPTER 16: NETWORK MANAGEMENT
MSG Component
The MSG component of the Syslog message usually contains some
additional information about the process that generated the message,
and then the text of the message itself.
There is no ending delimiter to the MSG component.
The MSG component must contain visible (printing) characters. The code
set traditionally and most often used has also been seven-bit ASCII in an
eight-bit field like that used in the PRI and HEADER parts. In this code set,
the only allowable characters are the ABNF VCHAR values (%d33-126)
and spaces (SP value %d32).
However, no indication of the code set used within the MSG is required,
nor is it expected. Other code sets may be used as long as the characters
used in the MSG are exclusively visible characters and spaces similar to
those described above.
Select a code set with the intended receiver in mind. A message
containing characters in a code set that cannot be viewed or understood
by a recipient yields no information of value to an operator or
administrator reviewing it.
MSG Component Fields
The MSG component has two fields:
TAG Field — The TAG is a string of ABNF alphanumeric characters that
must not exceed 32 characters. Any non-alphanumeric character
terminates the TAG field and is assumed to be the starting character of
the CONTENT field. The value in the TAG field is the name of the program
or process that generated the message.
CONTENT Field — The CONTENT contains the details of the message.
This has traditionally been a freeform message that gives some detailed
information of the event. Most commonly, the first character of the
CONTENT field that signifies the conclusion of the TAG field is the left
square bracket character ( [ ), a colon character ( : ), or a space character.
See “Originating Process Information in MSG” for more details.
Domain Name and Address in MSG
To identify the device that originated the message, you may want to
include its Fully-Qualified Domain Name (FQDN) and its IP address within
Syslog Security Considerations
405
the CONTENT field. Traditionally, however, only the hostname has been
included in the HOSTNAME field.
Originating Process Information in MSG
You may want to include some information about the process on the
device that generated the message. This information usually consists of
the process name and process ID (often known as the pid) for robust
applications. The process name is commonly displayed in the TAG field.
Quite often, additional information is included at the beginning of the
CONTENT field. The format
TAG [PID]:
is common. The left square bracket is used to terminate the TAG field in
this case, and is then the first character in the CONTENT field. If the
process ID is not needed, it may be omitted.
In that case, a colon and a space character usually follow the TAG. This
would be displayed as TAG:. In that case, the colon is the first character in
the CONTENT field.
Syslog Security
Considerations
Message Forgery
The Syslog process places Event Notification messages into files on that
system. This process relies upon the integrity of the system for the
protection of the messages. Be aware that event messages may be sent
accidentally, erroneously, and even maliciously. Because Syslog is a
relatively simple protocol, its operations are not secure to the point where
its integrity is robust.
An attacker may transmit Syslog messages (either from the machine from
which the messages are purportedly sent or from any other machine) to a
collector. In one case, an attacker may hide the true nature of an attack
amidst many other messages.
As an example, an attacker may start generating forged messages
indicating a problem on some machine. This may get the attention of the
system administrators who spend time investigating the alleged problem.
During this time, the attacker may be able to compromise a different
machine, or a different process on the same machine.
406
CHAPTER 16: NETWORK MANAGEMENT
In addition, an attacker may generate false Syslog messages to give
misleading indications of status or of events. For example, an attacker
may stop a critical process on a machine, which may generate a
notification of exit. The attacker may subsequently generate a forged
notification that the process had been restarted. System administrators
may accept that misinformation and not verify that the process had
indeed been restarted.
In some cases, to avoid such message forgeries, you can disable the
Syslog port on the system when Syslog logging is disabled.
Caution: Syslog messages sent to the remote server do not employ
encryption standards.
Periodic Timestamp
on Console (PTOC)
The PTOC feature sends a timestamp to the system console at a set
interval. If the system experiences a problem of any kind, this timestamp
can help you identify when the problem occurred. If the time interval is
set to X minutes, it will print every X minutes, whether or not any other
messages are printing.
To configure the PTOC:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Network Management > Syslog Settings.
3 Select a time value from the Periodic Timestamp on Console drop-down
list.
4 Click Apply.
Event Logging
You can view these event logs that the system maintains:
■
Adminlog — Tracks activities performed in the NBX NetSet utility
under the administrator login. The system never renames or deletes
the Adminlog. It continues to grow over time, but it is unlikely that the
size of the Adminlog file will ever grow to be a problem.
The system updates the adminlog file whenever system events occur,
such as:
■
When you enable or disable Supervisory Monitoring system-wide.
■
When you add, modify, or delete a domain.
Maintenance Alerts
■
■
407
When someone uses the wrong password when attempting to
view domain reports in the NBX NetSet utility.
When a user attempts to monitor another user by activating
feature code 425, and then uses the wrong password. (The log
updates after the maximum password retries are exceeded.)
■
Upglog — Tracks the history of upgrades and processes that occur
during upgrades.
■
TEP Logs — The 3C10116D T1 Digital Line Card and the 3C10165D
E1 Digital Line Card can generate logging information. TEP (T1, E1,
Primary Rate Interface) logs are stored on the system disk drive, even
for cards that are in remote locations, and you can use the NBX NetSet
utility to view, download, and delete log files. Each card has a separate
log, up to a maximum of five log files. When a log reaches its
maximum size, it begins to overwrite the oldest data.
Because TEP logging has a performance cost, it is disabled by default. To
enable TEP logging, contact your 3Com NBX Voice-Authorized Partner.
To view event logs, click Network Management > Event Logging and see
the online Help for more information.
Maintenance Alerts
If you have a V3001R or V5000 system with disk mirroring or dual power
supplies and with NBX Messaging enabled, you can:
■
Configure maintenance alert voice mail messages so that they appear
to come from one system user.
■
Designate up to 15 system users to receive maintenance alerts.
Alert messages are defined by the system. The content depends on the
cause of the alert.
When a user receives a maintenance alert message, the source of the
message depends on whether you have configured a system user as the
author of maintenance alert messages. See Table 76 for details.
Table 76 Source of Maintenance Alert Messages
Message Type
Author Configured
No Author Configured
Local Voice Mail
Message
The configured system user is
announced as the sender of the
message.
An outside caller is announced as the sender of the
message.
408
CHAPTER 16: NETWORK MANAGEMENT
Table 76 Source of Maintenance Alert Messages (continued)
Message Type
Author Configured
No Author Configured
Off-site E-mail
Message
The name of the configured system user The From field in the e-mail contains the word
appears in the From field of the e-mail. anonymous.
Off-site Voice Mail
Message
The system user is announced as the
sender of the message.
An outside caller is announced as the sender of the
message.
To set maintenance alerts:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Network Management > Maintenance Alerts. See the online Help
for procedures to set the maintenance alert author and specify users to
receive maintenance alerts.
17
COUNTRY SETTINGS
This chapter describes how to manage language settings for your system.
It describes:
■
Regional Software
■
Regional Settings
For more information about these topics and configuration procedures,
see the online Help.
Regional Software
Regional software includes local language voice prompts, regional tones
and cadences, and local language versions of certain user documentation
for your region.
A region is a country and language pair, for example, “China - Mandarin”
or “France - French.” The system uses English as the default. You must
install Country Packs to enable the system to support other languages.
Table 77
Country Pack
Documentation
Prompts
Tones and Cadences
Argentina_es.taz
Latin Spanish
Latin Spanish
Argentina
Australia.taz
US English
Australian
English
Australia
Brazil.taz
Brazilian
Portuguese
Brazilian
Portuguese
Brazil
China.taz
Chinese
Traditional
(Mandarin)
Chinese
Traditional
(Mandarin)
China
Chinese
Simplified
(Cantonese)
China
ChinaHongKong.taz Chinese
Simplified
(Cantonese)
410
CHAPTER 17: COUNTRY SETTINGS
Table 77
Country Pack
Documentation
Prompts
Tones and Cadences
NOTE: The LabelMaker utility included as part of the Chinese Country Packs is in US
English. PDF-format Chinese LabelMakers are available on the NBX Resource Pack
DVD.
Egypt_en.taz
US English
UK English
Egypt
France.taz
Parisian French
Parisian French
France
Germany.taz
German
German
Germany
Israel.taz
US English
Hebrew
Israel
Italy.taz
Italian
Italian
Italy
Mexico.taz
Latin Spanish
Latin Spanish
Mexico
NewZealand.taz
US English
New Zealand
English
New Zealand
Russia.taz
US English
Russian
Russia
SaudiArabia_en.taz
US English
UK English
Saudi Arabia
Spain.taz
European Spanish European
Spanish
Spain
UAE_en.taz
US English
UK English
United Arab Emirates
UnitedKingdom.taz
US English
UK English
United Kingdom
Release R6.x software includes a localized NetSet utility interface for
telephone users (Latin Spanish, Brazilian Portuguese, and Italian). The
localized NetSet interface is set by the host computer’s browser language
setting.
Install Regional
Software
To add regional software:
1 Click Country Settings > Install Regional Software.
2 See the online Help and the notes in the next sections for information
about how to manage regional software.
After you install regional software, you must designate it to be the
current system regional software. Click Country Settings > Regional
Settings.
Regional Software
Remove Regional
Software
411
To remove regional software:
1 Click Country Settings > Install Regional Software.
2 See the online Help and the notes in the next sections for information
about how to manage regional software.
You can remove regional software at any time. The system removes all
versions of the regional software that you select. For example, if you
choose to remove the “Mexico - Spanish” regional pack, the system
removes all versions of the selected regional software.
You cannot remove U.S. English.
When you remove a version of system software, the system verifies
whether the removal may leave any regional software unassigned to a
system software version.
Specific regional languages, tones and cadences, or voice prompts that
were associated with earlier releases may no longer be usable by recent
system software versions. 3Com recommends that you purge unused
regional software to conserve disk space.
You can only remove unused regional software immediately after you
delete a version of system software. If you choose not to remove this
software when prompted, you must either:
Regional Details
■
Wait until you remove a subsequent version of system software before
you can delete any unused regional software.
■
Remove all versions of the selected regional software on the system.
You can then install the required version.
The Regional Software Diagnostic Details window displays the status of
each region in the current system software. Table 78 defines the
displayed values.
Table 78 Diagnostic Details
Values
Description
In Use
The regional software is currently being used by the system.
Available
The regional software is fully loaded on the system, but it is
not currently in use.
412
CHAPTER 17: COUNTRY SETTINGS
Table 78 Diagnostic Details (continued)
Values
Description
Not Fully Installed
The system can access some parts of the regional software,
but not all. You may not have loaded the correct regional
software version for the system software you are running.
Error While Loading An error occurred while loading the regional software.
Re-install the software.
Nothing Installed
Regional Settings
The system is aware that this regional software exists, but no
version is installed.
After you install regional software and components from the regional
packs, you can enable regional settings. To enable these regional settings
in NetSet, you select the appropriate country and language for the system
voice prompts, the technical tones and cadences, and the online user
documentation.
To enable regional settings, select Country Settings > Regional Settings.
See the online Help for the procedure to enable regional settings.
See “Third-Party Drivers” on page 372 for information about how to
install regional language packs.
Advanced Regional Settings
The system also allows you to choose different regional settings for the
system voice prompts, the technical tones and cadences, and the online
user (not administrator) documentation. For example, you may require
local tones and cadences but want the documentation to be in English
and the voice prompts in Australian English.
You can select separate regional settings for:
■
Voice prompts — The Auto Attendant voice prompts.
■
Documentation — The NBX telephone guides, the NBX NetSet user
Help, the LabelMaker utility, and the quick reference cards.
■
Tones and Cadences — The tones and the patterns of rings (cadence)
versus silence. Tones and cadences vary from country to country.
Examples:
■
United States ringing cadence (pattern) is 2 seconds of ring
followed by 4 seconds of silence.
Regional Settings
■
■
413
United Kingdom ringing cadence is 2 rings within approximately 2
seconds followed by 2 seconds of silence.
United States busy tone is 0.75 seconds of tone followed by 0.75
seconds of silence.
To enable different regional settings:
1 Log on to the NBX NetSet utility using the administrator login ID and
password.
2 Click Country Settings > Regional Settings > Advanced Regional Settings.
3 See the online Help for more information.
414
CHAPTER 17: COUNTRY SETTINGS
18
TROUBLESHOOTING
This chapter contains maintenance and troubleshooting information to
help you resolve simple problems. It describes these topics:
■
Telephone Local User Interface Utility
■
The 3Com Telephone Local Configuration Application
■
Using H3PingIP
■
System-level Troubleshooting
■
Connecting a Computer to a Serial Port
■
Servicing the Network Call Processor Battery
■
Getting Service and Support
The system hardware needs no routine maintenance. However, perform
periodic backups of the configuration and license databases, especially
after you make changes to system or user configurations.
Telephone Local
User Interface
Utility
This section contains information about how to use the telephone
diagnostic and configuration utility called the Local User Interface (LUI). It
describes:
■
Using the LUI Utility
■
Using the LUI Menu Options
Each 3Com telephone supports the Local User Interface (LUI). The LUI
utility enables you to perform these tasks:
■
View telephone settings, both the active settings and the settings
stored in the telephone’s memory
■
Set telephone IP address, subnet mask, and default gateway
■
Specify the IP address of the Call Processor
416
CHAPTER 18: TROUBLESHOOTING
■
Test the telephone buttons, display panel, and status lights
■
Clear all device settings
■
Specify the MAC address of the Call Processor (test environment
option)
■
View firmware information (technician option)
■
Test connectivity
■
Restart the telephone
Early model 3Com Telephones support an earlier version of the LUI utility
that has a slightly different menu. For information about this earlier
version of the LUI utility, see your NBX Voice-Authorized Partner or a
version of the NBX Administrator’s Guide from a release prior to release
R4.3.
Using the LUI Utility
To start the LUI utility:
1 Cycle power to the telephone by disconnecting and then reconnecting its
power connector, and then access the LUI menu options (see step 2)
before the telephone finishes its download of code from the Call
Processor).
For telephones that use a powered Ethernet cable instead of a power
adapter, disconnect and then reconnect the Ethernet cable.
You do not need to cycle power to 3101B and 3102B Business
Telephones.
2 To access (or exit from) the LUI utility:
■
On the 3Com 3102 and 3102B Business Telephone, press the Program
button:
■
On 3Com 1102, 2102, or 2102-IR Business Telephones, press
Program:
■
On 3Com 3103 Manager’s Telephones and 3101, 3101B, or 3101SP
Basic Telephones, press the center button in the cursor control button
group:
Telephone Local User Interface Utility
417
■
On the 3Com 2101 Basic Telephone, press the MSG button:
■
On 3106C and 3107C Cordless Telephones, press the Feature button:
The buttons you use to enter information vary with each telephone:
■
3Com 3103 Manager’s Telephone, see Figure 27 on page 418.
■
3Com 3102 and 3102B Business Telephone, see Figure 28 on
page 419.
■
3Com 3101, 3101B or 3101SP Basic Telephones, see Figure 29 on
page 420.
■
3Com 1102, 2102, or 2102-IR Business Telephones, see Figure 30 on
page 421.
■
3Com 2101Basic Telephone, see Figure 31 on page 422.
■
3Com 3106C Cordless Telephone, see Figure 32 on page 423.
■
3Com 3107C Cordless Telephone, see Figure 33 on page 424.
Table 79 on page 425 and Table 80 on page 429 describe each LUI utility
menu item.
418
CHAPTER 18: TROUBLESHOOTING
Figure 27 Local User Interface Controls on the 3Com 3103 Manager’s
Telephone
1
2
4
3
1 Display panel.
2 Access buttons AB1-AB8 (from bottom to top) select menu items.
3 Scroll buttons:
■
Center select button starts and exits from the LUI utility or exits from a
menu item and moves to the next higher menu. If you press the center
select button before you save a change to a setting, you exit the menu
item without saving the change.
■
Up and down buttons move up or down through the LUI menu and
select hex digits when editing a MAC address.
■
Left and right buttons position the cursor in the display panel when
you edit a setting, such as an IP address or an Call Processor MAC
address.
4 Key pad numeric keys select menu items or enter numeric characters in a
menu item. Use the # key to save changes after you edit an item.
Telephone Local User Interface Utility
419
Figure 28 Local User Interface Controls on the 3Com 3102 and 3102B Business
Telephone
6
5
1
2
3
4
1 Display panel.
2 On 3102 Business Telephones, the soft buttons move the cursor left or
right and the middle button is inactive. On 3102B Business Telephones,
the soft buttons are inactive.
3 Key pad numeric keys select menu items or enter numeric characters in a
menu item. Use the # key to save changes after you edit an item.
4 Access buttons AB1-AB4 (from bottom to top) select menu items.
5 Program button:
■
Start and exit from the LUI utility.
■
Exit from a menu item and move to the next higher menu. If you press
the Program button before you save a change to a setting, you exit
the menu item without saving the change.
6 Scroll buttons:
■
Up and down buttons move up or down through the LUI menu and
select hex digits when editing a MAC address.
■
Left and right buttons position the cursor in the display panel when
you edit a setting, such as an IP address. On 3102B Business
420
CHAPTER 18: TROUBLESHOOTING
Telephones, the left button erases the characters of a setting and the
right button is inactive.
Figure 29 Local User Interface Controls on 3Com 3101, 3101B, and 3101SP
Basic Telephones
1
2
5
3
4
1 Display panel.
2 On 3101 and 3101SP Business Telephones, the soft buttons move the
cursor left or right and the middle button is inactive. On 3101B Business
Telephones, the soft buttons are inactive.
3 Key pad numeric keys select menu items or enter numeric characters in a
menu item. Use the # key to save changes after you edit an item.
4 Access buttons AB1-AB4 (from left to right) select LUI menu items.
5 Scroll buttons:
■
Center select button starts and exits from the LUI utility or exits from a
menu item and moves to the next higher menu. If you press the center
select button before you save a change to a setting, you exit the menu
item without saving the change.
■
Up and down buttons move up or down through the LUI menu and
select hex digits when editing a MAC address.
■
Left and right buttons position the cursor in the display panel when
you edit a setting, such as an IP address. On 3101B Business
Telephones, the left button erases the characters of a setting and the
right button is inactive.
Telephone Local User Interface Utility
421
Figure 30 Local User Interface Controls on the 3Com 1102, 2102,and 2102-IR
Business Telephones
6
1
2
3
4
5
1 Display panel.
2 Soft buttons move the cursor left or right. The middle button is not used.
3 Program button starts and exits from the LUI utility or exits from a menu
item and moves to the next higher menu. If you press the Program button
before you save a change to a setting, you exit the menu item without
saving the change.
4 Key pad numeric keys select menu items or enter numeric characters in a
menu item. Use the # key to save changes after you edit an item.
5 Access buttons AB1-AB4 (from top to bottom) select LUI menu items.
6 Scroll buttons move up or down through the LUI menu and select hex
digits when editing a MAC address.
422
CHAPTER 18: TROUBLESHOOTING
Figure 31 Local User Interface Controls on the 3Com 2101 Basic Telephone
1
2
7
6
3
5
4
1 Display panel.
2 Soft buttons move the cursor left or right. The middle button is not used.
3 Key pad numeric keys select menu items or enter numeric characters in a
menu item. Use the # key to save changes after you edit an item.
4 Access buttons AB1-AB3 select LUI menu items.
5 Volume Down button selects LUI menu item AB4.
6 MSG (voice mail message) button starts and exits from the LUI utility or
exits from a menu item and moves to the next higher menu. If you press
the MSG button before you save a change to a setting, you exit the menu
item without saving the change.
7 Scroll buttons move up or down through the LUI menu and select hex
digits when editing a MAC address.
Telephone Local User Interface Utility
423
Figure 32 Local User Interface Controls on the 3106C Cordless Telephone
1
2
3
7
6
4
5
1 Display panel.
2 Xfer (transfer) button scrolls right in the display panel.
3 Hold button scrolls left in the display panel.
4 Key pad for selecting menu items or entering numeric characters. Use #
to commit changes. Use * to exit from a menu item or from the LUI utility.
If you have not already saved changes by pressing #, pressing * exits that
menu item without saving changes.
5 Access buttons AB1-AB4 (from left to right) select LUI menu items.
6 Feature button starts the LUI utility. After you start the LUI utility, the
Feature button:
■
Scrolls up the LUI menu.
■
Selects hex digits when editing a MAC address.
7 Conf (conference) button:
■
Scrolls down the LUI menu.
■
Selects hex digits when editing a MAC address.
424
CHAPTER 18: TROUBLESHOOTING
Figure 33 Local User Interface Controls on the 3107C Cordless Telephone
1
2
3
7
6
4
5
1 Display panel.
2 Xfer (transfer) button scrolls right in the display panel.
3 Hold button scrolls left in the display panel.
4 Key pad for selecting menu items or entering numeric characters. Use #
to commit changes. Use * to exit from a menu item or from the LUI utility.
If you have not already saved changes by pressing #, pressing * exits that
menu item without saving changes.
5 Access buttons AB1-AB4 (from left to right) select LUI menu items.
6 Feature button starts the LUI utility. After you start the LUI utility, the
Feature button:
■
Scrolls up the LUI menu.
■
Selects hex digits when editing a MAC address.
7 Conf (conference) button:
■
Scrolls down the LUI menu.
■
Selects hex digits when editing a MAC address.
Telephone Local User Interface Utility
Using the LUI Menu
Options
425
Table 79 lists the LUI menu options for 3101B and 3102B Business
telephones, and the 3103 Manager’s telephone. See Table 80 on
page 429 for the list of LUI menu options for all other 3Com telephones.
Table 79 LUI Menu Options for 3101B, 3102B, and 3103 Telephones
Menu Option
Description
NOTE: NCP refers to the Call Processor.
1 View Settings
Press 1 on the number pad and scroll to view these options:
My MAC Address – MAC address of this telephone.
NCP MAC Address – MAC address of Call Processor. All Fs, the
normal value for this setting, indicates that the telephone
responds to any Call Processor.
SW Build OPs Id — The current version of the application code
on the telephone
SW Build LIB Id —The current version of the library code on the
telephone (used for VCX).
SW Build DSP Id — The current version of Digital Signal
Processor (DSP) code on the telephone.
Serial Number – Telephone serial number and hardware
version.
Phone Port Speed – Speed and duplex setting of the LAN
connection.
PC Port Speed – The speed and duplex setting of the PC port to
the device, if any, connected to the port.
Note: The next four settings are all valid only if the device
downloads through IP (layer 3). These four settings are acquired
from either DHCP or a setting in the telephone’s memory
My IP Address – Active IP address of this telephone.
Subnet Mask – Active IP mask.
Gateway IP Address – Active default gateway IP address.
NCP IP Address – Active IP address of the Call Processor with
which this telephone communicates.
Alt. Server IP – Active IP address of a secondary download
server with which this telephone communicates, acquired from
either DHCP option 184 or a setting in the telephone’s memory.
(Valid for 3Com VCX Telephone systems only.)
426
CHAPTER 18: TROUBLESHOOTING
Table 79 LUI Menu Options for 3101B, 3102B, and 3103 Telephones
Menu Option
Description
VLAN Configuration – Active VLAN for this telephone,
acquired from either DHCP option 184 or a setting in the
telephone’s memory. Valid for 3Com VCX Telephone systems
only.
EE-My IP — The IP address configured in the telephone’s
memory.
EE-Subnet Mask — The IP mask configured in the telephone’s
memory.
EE-Gateway IP — The default gateway IP address configured in
the telephone’s memory.
EE-NCP IP —The Call Processor IP address configured in the
telephone’s memory.
EE-Alt Server IP — Secondary download server address
configured in the telephone’s memory.
EE-VLAN Config — VLAN values configured.
Flash - BootStrap —The version number of the software that
starts when telephone first powers up.
Flash Download —The version number of the software that
downloads new code to the telephone.
Flash Operation — The version number of the operational
image on the telephone.
2 Configure IP
Address
3 Configure
SubNetMask
4 Configure
Gateway IP
Address
Lets you specify the IP information for this telephone.
When entering an IP address:
■
Use the key pad to enter digits 0–9.
■
Use the left and right soft keys or scroll keys to move the
cursor left or right.
■
If any of the fields within the IP address contain only one or
two digits, add leading zeros.
Example: Enter 10.234.1.125 as 010.234.001.125
■
To change a telephone back to its default setting, enter 255
for each octet of the IP address. To clear all configured
settings and return to factory defaults, select menu option 6
Advanced Settings > 3 Set EEPROM - Default.
■
Press the # key to commit your address change.
Telephone Local User Interface Utility
427
Table 79 LUI Menu Options for 3101B, 3102B, and 3103 Telephones
Menu Option
Description
5 Configure NCP
IP Address
Lets you specify the IP address of the Call Processor. If the
telephone is on the same subnetwork as the Call Processor you
never need to specify the Call Processor IP address. If the
telephone is on a different subnetwork, then you must enter this
information or provide it by using DHCP option 184.
When entering an IP address:
6 Advanced
Settings
■
Use the key pad to enter digits 0–9.
■
Use the left and right soft keys or scroll keys to move the
cursor left or right.
■
If any of the fields within the IP address contain only one or
two digits, add leading zeros.
Example: Enter 10.234.1.125 as 010.234.001.125
■
To change a telephone back to its default setting, enter 255
for each octet of the IP address. To clear all configured
settings and return to factory defaults, select menu item AB4.
■
Press the # key to commit your address change.
1 Set NCP MAC Address — Lets you specify the MAC address
of the Call Processor. In all but special circumstances, the system
messages communicate this information and you do not need to
manually configure the MAC address.
To change a telephone back to its default setting, enter all Fs for
the Call Processor MAC address.
2 Show EEPROM Contents — Lets you scroll through the
locations in the memory of the telephone. The information is
presented in hexadecimal format and can be properly
interpreted only by a 3Com service person.
3 Set EEPROM - Default — Restores the telephone to default
settings by clearing these configured settings:
■
IP Information — My IP, Subnet Mask, Gateway IP, NCP-IP,
and the Alt Download Server IP return to 255.255.255.255.
■
NCP MAC address — The Call Processor MAC address
returns to ff:ff:ff:ff:ff:ff.
■
SIP Parameters — All SIP specific parameters will be set to
default 0xffff (data parameters) or 255.255.255.255 for IP
addresses.
NOTE: If you select this option you are prompted to verify
your action before the system clears the EEPROM
428
CHAPTER 18: TROUBLESHOOTING
Table 79 LUI Menu Options for 3101B, 3102B, and 3103 Telephones
Menu Option
Description
4 Force Operational SW Upgrade — Resets the device. You
can perform the same task by removing power from the
telephone. Forces the telephone to retrieve an image from the
downloader.
5 Hardware Reset — Resets the telephone and starts with the
bootstrap code.
6 Ping H3/IP — Runs an H3 IP ping test. See Using H3PingIP for
more information.
7 Test - LED & LCD — Turns on all LEDs for 5 seconds, then fills
every pixel on the display panel for 5 seconds.
8 Test - Buttons — Puts the telephone in the button test state.
Press any telephone button to see a description of the button’s
function. To return to the main menu, press the pound ( #)
button twice:
9 Audio Collection — Lets you specify a PC address to store
audio packets when you are on a call. Used to debug audio
quality issues that may arise in the field.
7 Network
Configuration
1 Set VLAN Configuration — Lets you to set the VLAN ID. If
the VLAN ID consists of less than 4 digits, add leading zeros. For
example, if the VLAN ID is 5, you must enter 0005 to ensure that
the correct VLAN ID is stored.
8 Diagnostics
Runs diagnostics. This option requires a password, which your
3Com Technical Support representative will provide, if necessary.
Modify Display
Note: On the 3103 Manager’s telephone only
Lets you adjust the display panel’s contrast.
Select TOD
Format
Note: On the 3103 Manager’s telephone only
Lets you select the time of day format:
■
None
■
12 hour format
■
24 hour format
Telephone Local User Interface Utility
429
Table 80 lists the LUI menu options for 3Com telephones except the
3101B and 3102B Business telephones, and the 3103 Manager’s
telephone. See Table 79 on page 425 for a list of LUI menu options for
the 3101B and 3102B Business telephones, and the 3103 Manager’s
telephone.
Table 80 LUI Menu Options for 3Com Telephones
Menu Option
Description
NOTE: NCP refers to the Call Processor.
1 View Settings
Press 1 on the number pad and scroll to view these options:
MAC Address – MAC address of this telephone.
NCP MAC Address – MAC address of Call Processor. All Fs, the
normal value for this setting, indicates that the telephone
responds to any Call Processor.
SW Build Ident. – Software version running on this telephone.
Serial # Rev – Telephone serial number and hardware version.
Phone Port Speed – Speed and duplex setting of the LAN
connection.
PC Port Speed – The speed and duplex setting of the PC port to
the device, if any, connected to the port.
Note: The next four settings are all valid only if the device
downloads through IP (Layer 3). These four settings are acquired
from either DHCP or a setting in the telephone’s memory
My IP Address – Active IP address of this telephone.
Subnet Mask – Active IP mask.
Gatwy IP Address – Active default gateway IP address.
NCP IP Address – Active IP address of the Call Processor with
which this telephone communicates.
ALT SrvrIP – Active IP address of a secondary download server
with which this telephone communicates, acquired from either
DHCP option 184 or a setting in the telephone’s memory. (Valid
for 3Com VCX Telephone systems only.)
430
CHAPTER 18: TROUBLESHOOTING
Table 80 LUI Menu Options for 3Com Telephones (continued)
Menu Option
Description
VLAN Config – Active VLAN for this telephone, acquired from
either DHCP option 184 or a setting in the telephone’s memory.
Valid for 3Com VCX Telephone systems only.
Mem- My IP Addr – The IP address configured in the
telephone’s memory though the LUI utility.
Mem- Subnet Mask – The IP mask configured in the
telephone’s memory though the LUI utility.
Mem- Gatwy IP – The default gateway IP address configured in
the telephone’s memory though the LUI utility.
Mem- NCP IP Addr – The Call Processor IP address configured
in the telephone’s memory though the LUI utility.
Mem- ALT SrvrIP – Secondary download server address
configured in the telephone’s memory. (Valid for 3Com VCX
Telephone systems only.)
Mem- VLAN Config – VLAN values configured in the
telephone’s memory. Valid for 3Com VCX Telephone systems
only.
2 Set my IP
Lets you specify the IP information for this telephone.
3 Set SubNMsk
When entering an IP address:
4 Set GatwyIP
■
Use the key pad to enter digits 0–9.
■
Use the left and right soft keys or scroll keys to move the
cursor left or right.
■
If any of the fields within the IP address contain only one or
two digits, add leading zeros.
Example: Enter 10.234.1.125 as 010.234.001.125
■
To change a telephone back to its default setting, enter 255
for each octet of the IP address. To clear all configured
settings and return to factory defaults, select menu item AB4.
■
Press the # key to commit your address change.
Telephone Local User Interface Utility
431
Table 80 LUI Menu Options for 3Com Telephones (continued)
Menu Option
Description
5 Set NCP IP
Lets you specify the IP address of the Call Processor. If the
telephone is on the same subnetwork as the Call Processor you
never need to specify the Call Processor IP address. If the
telephone is on a different subnetwork, then you must enter this
information or provide it by using DHCP option 184.
When entering an IP address:
■
Use the key pad to enter digits 0–9.
■
Use the left and right soft keys or scroll keys to move the
cursor left or right.
■
If any of the fields within the IP address contain only one or
two digits, add leading zeros.
Example: Enter 10.234.1.125 as 010.234.001.125
■
To change a telephone back to its default setting, enter 255
for each octet of the IP address. To clear all configured
settings and return to factory defaults, select menu item AB4.
■
Press the # key to commit your address change.
6 VCX Cnfig
Menu
Not used in an NBX environment. 3Com telephones can operate
as SIP clients for the 3Com VCX Telephone System. This option
opens a submenu that allows you to set telephone operating
settings for a VCX environment.
7 Reserved
Reserved for future use.
8 Test LED & LCD
On all 3Com Business Telephones and 3Com 3101 and 3101SP
Basic Telephones, turns on all LEDs for 5 seconds, then fills every
pixel on the display panel for 5 seconds.
On all 3Com Basic Telephones, turns on the icons and words on
the right side of the display panel for 5 seconds.
Icons: Telephone icon plus the number 1 (top line) and
telephone icon plus the number 2 (bottom line)
Words: FWD (top line) and IN (bottom line).
432
CHAPTER 18: TROUBLESHOOTING
Table 80 LUI Menu Options for 3Com Telephones (continued)
Menu Option
Description
9 Test – Buttons
Puts the telephone in the button test state. Press any telephone
button to see a description of the button’s function. To return to
the main menu, press the menu button twice:
0
EEPROM-Default
■
On 3102 Business Telephones:
■
On 1102, 2102, or 2102-IR Business Telephones:
■
On 3101 or 3101SP Basic Telephones or 3103 Manager’s
Telephones:
■
On 2101 Basic Telephones:
■
On 3106C or 3107C Cordless Telephones, *.
Restores the telephone to default settings by clearing these
configured settings:
IP Information — My IP, Subnet Mask, Gateway IP, NCP-IP, and
the Alt Download Server IP return to 255.255.255.255.
NCP MAC address — The Call Processor MAC address returns
to ff:ff:ff:ff:ff:ff.
SIP Parameters — All SIP specific parameters will be set to
default 0xffff (data parameters) or 255.255.255.255 for IP
addresses.
NOTE: If you select this option you are prompted to verify your
action before the system clears the EEPROM.
AB1 Set NCP
MAC
NOTE: This
setting is for test
networks only.
Lets you specify the MAC address of the Call Processor. In all but
special circumstances, the system messages communicate this
information and you do not need to manually configure the
MAC address.
To change a telephone back to its default setting, enter all Fs for
the Call Processor MAC address.
AB2 Show
EEProm
Lets you scroll through the locations in the memory of the
telephone. The information is presented in hexadecimal format
and can be properly interpreted only by a 3Com service person.
AB3 Ping H3/IP
Runs an H3 IP ping test. See Using H3PingIP for more
information.
The 3Com Telephone Local Configuration Application
433
Table 80 LUI Menu Options for 3Com Telephones (continued)
Menu Option
Description
AB4 RESET Phone Resets the device. You can perform the same task by removing
power from the telephone. However, Option AB4 can be useful
for cordless phones, which cannot easily be disconnected from
power.
The 3Com
Telephone Local
Configuration
Application
You can manually configure most 3Com telephones using the telephone
Local User Interface (LUI) utility to define the settings the device needs to
communicate with the Call Processor. For the 3100 Entry Telephone,
which does not have a display panel to show configuration information,
use the 3Com Telephone Local Configuration (TLC) application.
The TLC application enables you to specify the information that a device
requires to communicate with the Call Processor over a routed network
without using DHCP. You must still use the Auto Discover feature or
manual configuration through the NetSet utility to add the device to the
system database.
Installing the 3Com
Telephone Local
Configuration
Application
The TLC application is a Windows program that you install and run from a
PC.
To install the TLC application:
1 Insert the NBX Resource Pack DVD into your DVD drive. If the autorun
program does not start the DVD browser program, navigate to the DVD
and start autorun.exe.
2 Click NBX Applications and then click Telephone Local Configuration.
The installation program creates a shortcut on your Start menu that you
can use to launch the TLC application.
Using the Telephone
Local Configuration
Application
After you download and install the TLC application, use the Windows
Start menu to launch it.
Follow these steps to use the TLC application to configure a 3Com
device:
■
Discover the 3Com device:
■
Connect the 3Com device to the same subnetwork as the PC that
is running the TLC application.
434
CHAPTER 18: TROUBLESHOOTING
■
■
Enter the device’s MAC address (found on the label on the
underside of the 3Com device) into the TLC interface.
After the TLC application connects to the device, specify the device IP
settings you want to assign.
After you configure a device, you can open the device list window again
and configure another device. Note that the device list can include any
3Com device including switches and routers.
Using H3PingIP
You can use the H3PingIP menu item to ping another device on the
network to test the telephone’s connectivity and to check the packet
delay.
When you use H3PingIP to test for connectivity, use the IP address of a
device that is connected to the Call Processor. Do not use the Call
Processor IP address. The 3Com Business Telephone uses the IP Gateway
and subnet mask information programmed into it using the AB16 and
AB17 buttons.
H3PingIP shows the following information:
■
Port — The UDP Destination Port
■
Tx — The number of packets transmitted
■
Rx — The number of packets received
■
mS — The delay time, in milliseconds
If you ping a device on a subnetwork different than the one on which the
telephone is located, the delay time is greater.
System-level
Troubleshooting
For each symptom listed in Table 81, perform the suggested actions in the
order listed.
WARNING: Before you remove any component, shut down the system
software and then turn off the power to the chassis by removing the
chassis power cord. If the system has two power supplies, remove both
power cords.
System-level Troubleshooting
435
Table 81 Troubleshooting Actions
Symptom
Possible Cause
Suggested Action
Date/time
display on
telephones is
wrong, either
incorrect date
or shows
random
characters.
A power surge
If the display shows incorrect date, use NetSet
has corrupted the to reset the system time. If the display shows
system time.
random characters, for example, 00; 0 #, you
must:
1 Disconnect power to the chassis that holds
the Call Processor.
2 Wait 60 seconds.
3 Reconnect power to the system.
4 Use NetSet to enter the correct date and
time.
Problem with Call Contact your 3Com NBX Voice - Authorized
Processor battery. Partner.
Your browser
cannot find
NetSet.
No IP connectivity Verify that the computer you are using to run
the browser has network connectivity. See
“Establishing IP Connectivity” in the NBX
Installation Guide.
Routing problems If your local IP environment includes a proxy
server, you may need to reconfigure your
browser parameters to ignore the proxy server.
See the online Help for your browser.
Invalid IP
configuration
The system has a default IP configuration that
may need to be changed to match your local IP
environment. Temporarily change the IP
configuration of your computer so that the
subnetwork configuration matches the system
configuration. Specify 255.255.255.0 as the
subnetwork and use IP address
192.168.1.191. After you change your
computer’s IP configuration, connect to the
system and change its IP settings to match the
IP environment of your local network. Change
your computer’s IP configuration back to its
original settings, and then connect to NetSet
using the new IP address. See “Establishing IP
Connectivity” in the NBX Installation Guide.
Cannot open
NetSet using
the
administrator
username and
password.
The CAPS LOCK
key on your
keyboard is
activated.
NetSet username and passwords are
case-sensitive. For example, NetSet accepts
“administrator” but it rejects “Administrator”
and “ADMINISTRATOR”.
Callers on hold
do not hear
music.
No music source is See “Adding External Hardware” in the NBX
connected to the Installation Guide for more information.
Call Processor.
436
CHAPTER 18: TROUBLESHOOTING
Table 81 Troubleshooting Actions (continued)
Symptom
Digital Line Card
Troubleshooting
Possible Cause
Suggested Action
MOH audio is
disabled.
Enable MOH audio in System-Wide Settings.
See “Connecting a Music-on-Hold (MOH)
Input Device” in the NBX Installation Guide.
MOH volume is
set too low.
See “Adjusting Music-on-Hold (MOH)
Volume” in the NBX Installation Guide.
Lose date and
time when
rebooting the
system.
Problem with the
battery on the
Call Processor.
See “Servicing the Network Call Processor
Battery” on page 449.
NetSet is very
slow in
responding.
Your network
uses a proxy
server for Internet
access.
A common networking practice is to employ a
proxy server to shield your network from
intrusion by unauthorized users. However,
communications with NetSet do not need to
pass through the proxy server. To speed access
to NetSet, configure your browser to access
the system without going through the proxy
server.
All greetings
and prompts
are missing. For
example,
calling the Auto
Attendant or a
user’s mailbox
produces
silence instead
of the expected
greetings.
The wrong
message
compression
format was
selected.
Prior to R1.1.0, all audio used MuLaw
compression. With R1.1.0, audio, that is, any
prompt, message, or greeting, was recorded
using ADPCM compression. If you are running
R1.1.0 or higher, leave the compression format
set to ADPCM. The ability to select the format
allows you to migrate existing data into an
older database for backwards compatibility.
Caller ID
information is
not appearing
when an
outside call
arrives.
Your local
telephone
company is not
providing Caller ID
service to you.
Caller ID is typically an optional service which
you must order from your telephone company.
You are
answering the
telephone before
the Caller ID
information is fully
received.
Caller ID information does not appear
immediately. It usually appears between the
first and second rings. If you answer the call
too quickly, the information is never received.
If you transfer the call, the person you transfer
the call to sees your ID instead of the ID of the
original caller.
In release R2.6 and all later releases, the
compression is set to ADPCM and you cannot
change it.
You may be able to see caller ID by number or
by name (or both) depending on the service
your telephone company provides.
To troubleshoot a Digital Line Card correctly, decide if the origin of the
problem is:
System-level Troubleshooting
■
The hardware
■
The software configuration
■
The CSU (Channel Service Unit)
■
The telephone company’s line
437
To eliminate the Digital Line Card (T1 or E1) attach a loop back connector
in place of the telephone company’s line. Configure the card as described
in the appropriate section of Chapter 5.
The 3C10116D T1 card and 3C101156D E1 card can respond to
commands from the Central Office to loop back data at different points
for diagnostic purposes. You enable each loopback test using the NBX
NetSet utility. You initiate the Local and Framer loopback tests using the
NBX NetSet utility. The Line and Payload loopback tests must be initiated
by the Central Office or by test equipment emulating Central Office
equipment. For more information about how to enable loopback tests,
see “Using Loopback Tests” on page 190.
After you complete the configuration, and with the loopback connector
in place, verify that the Nominal status light (3C10165C E1 card or
3C10116C T1 card) on the front panel of the Digital Line Card is turned
on (appears steady and green). For the 3C10165D E1 card and
3C10116D T1 card, verify that the CO status light is green.
■
If the Nominal or CO status light does not turn on, the problem is
most likely in the Digital Line Card. Contact your 3Com
Voice-Authorized Partner to report the problem.
■
If the Nominal or CO light turns on, the problem is either in the CSU
(Channel Service Unit) or in the telephone company’s line. Contact the
telephone company for assistance.
The 3C10165D E1 Card and the 3C10116D T1 card each have an
onboard CSU. You can view CSU statistics for the card through the NBX
NetSet utility. For more information see “Viewing CSU State Information
and Statistics” on page 187.
Alarm Conditions
(Overview)
T1 and E1 Digital Line Cards may experience these alarm conditions:
■
Red Alarm — Indicates one of these conditions:
■
Loss of Signal (LOS)
■
Loss of Framing (LOF) also known as Out of Frame (OOF)
438
CHAPTER 18: TROUBLESHOOTING
■
Blue Alarm — Indicates an Alarm Indication Signal (AIS)
■
Yellow Alarm — Indicates a Remote Alarm Indication (RAI)
An alarm condition may be one of these:
■
Signal — Information transmitted either in the upstream or
downstream direction, warning of a detected failure:
■
State — A condition, activated at a terminal device, indicating that a
problem exists and remedial action is required.
T1 and E1 Digital Line Cards are considered “downstream” equipment.
Alarm Descriptions
Red Alarm
■
Carrier Fail Alarm (Red CFA) — A state that exists at a downstream
terminal device, based upon the terminal device detecting an
incoming LOS or LOF.
Blue Alarms
■
AIS, Keep-alive/Blue — A signal that is transmitted instead of the
normal signal to maintain transmission continuity and to indicate to
the receiving equipment that there is a transmission interruption either
at the equipment that is generating the AIS signal or upstream of that
equipment. The all ones signal is generated:
■
To maintain transmission continuity
■
To notify downstream equipment of a transmission fault
■
To indicate to downstream equipment that a DS1 framed signal is
not being generated
The transmission fault may be located at the equipment that is
generating the alarm signal, or it may be located upstream of that
equipment.
■
AIS CFA (also known as Blue CFA) — A state that exists at the
downstream equipment and indicates that it has detected an AIS
signal from the upstream equipment.
Yellow Alarms
■
RAI (also known as Yellow Alarm Signal) — A signal transmitted in the
outgoing direction when a terminal indicates that it has lost the
incoming signal. The terminal equipment generates the Yellow Alarm
Signal for a minimum of 1 second using one of these methods:
System-level Troubleshooting
■
■
■
Alarms on NBX
Digital Line Cards
439
If you are using Super Frame (SF), the terminal equipment
generates the Yellow Alarm Signal by setting the second bit in all
channels of the Super Frame to 0 (zero).
If you are using Extended Super Frame (ESF), the terminal
equipment generates the Yellow Alarm Signal by sending an
alternating pattern of 8 ones followed by 8 zeros on the Facilities
Data Link (FDL).
Yellow CFA — A state that is activated at the terminal equipment
when the terminal equipment detects a Yellow Alarm Signal. The
Yellow Alarm Signal comes from the equipment at the other end
when the far end equipment enters a Red CFA state. See Red Alarm,
earlier in this section.
T1 and E1 Digital Line Cards support all of the alarm states and signals
described in “Alarm Descriptions” on page 438. Table 82, next, and
Table 83 on page 440 describe how the status lights indicate alarm
conditions on Digital Line Cards.
Table 82 3C10165, 3C10165B, 3C10165C, 3C10116, and 3C10116C Status
Lights and Error Conditions
Status Light
Purpose
Nominal
On: There are no error or alarm conditions.
CF (Carrier Fail)
On: A Red Alarm state or Blue Alarm state exists on the card.
To find out which alarm state exists:
Flashing: A call is active on at least one channel.
1 Log on to the NBX NetSet utility using the administrator ID
and password.
2 Click PSTN Gateway Configuration > Digital Line Cards.
3 In the Select Device Type list, select T1 Span List or ISDN
PRI Span List, and then click Apply.
4 Select the span you want and click Status. The words Red
Alarm or Blue Alarm appear in the Status field.
440
CHAPTER 18: TROUBLESHOOTING
Table 82 3C10165, 3C10165B, 3C10165C, 3C10116, and 3C10116C Status
Lights and Error Conditions (continued)
Status Light
Purpose
RA (Remote Alarm)
On: A Yellow Alarm state on the card. To confirm that the
Yellow Alarm state exists:
1 Log on to the NBX NetSet utility using the administrator ID
and password.
2 Click PSTN Gateway Configuration > Digital Line Cards.
3 In the Select Device Type list, select T1 Span List or ISDN
PRI Span List, and then click Apply.
4 Select the span you want and click Status. The words
Yellow Alarm appear in the Status field.
NOTE: This light is used only on the T1 Digital Line Card.
LB (Loop Back)
On: The card is in loop-back testing mode.
NOTE: This light is not used to indicate any of the Red, Blue,
or Yellow alarms.
Table 83 3C10165D and 3C10116D Status Lights and Error Conditions
Status Light
Purpose
CO
Green: There are no error or alarm conditions.
Amber: An alarm condition at the remote end or the CO is
not connected or available. To find out which alarm state
exists:
1 Log on to the NBX NetSet utility using the administrator ID
and password.
2 Click PSTN Gateway Configuration > Digital Line Cards.
3 In the Select Device Type list, select T1 Spans or ISDN PRI
Spans, and then click Apply.
4 Select the span you want and click Status. The words Red
Alarm or Blue Alarm appear in the Status field.
Configuration and
Status Reports
You can obtain the status of all Digital Line Cards in the system with
either of these two methods:
Select PSTN Gateway Configuration > Digital Line Cards and:
■
Click Config & Status Report, which displays a formatted report with
headings shown in a larger font in the window.
System-level Troubleshooting
■
441
Click Export Report, which displays an unformatted report in the
window. To save the report as an ASCII text file, select Save as from
the File menu of your browser.
Table 84 describes in alphabetical order (not the order of appearance) the
headings in the Configuration and Status Report.
Table 84 Configuration and Status Report Headings
Heading
Description
#Chs
Number of channels.
#Dsp
Number of digital signal processors.
#OffChs
Number of channels in the offline state.
#OnChs
Number of channels in the online state.
AEClosed
Autoattendant extension when business is closed.
AELunch
Autoattendant extension when business is at lunch.
AEOpen
Autoattendant extension when business is open.
AEOther
Autoattendant extension for Other hours.
ais
TEP performance data. Alarm Indication Signal. The number of
seconds in which an ais was transmitted. An ais signal is
transmitted in lieu of the normal signal to maintain
transmission continuity and indicate to the receiving terminal
that there is a transmission fault located either at the
transmitting terminal or upstream of the transmitting terminal.
Also referred to as a Blue Alarm.
aissp
TEP performance data. T1.231 Near End. Number of seconds
when loss of frame encountered.
ANI
Automatic Number Identification. The telephone number from
which the call originated.
Audio Input
Numeric value of audio input control setting.
Audio Output
Numeric value of audio output control setting.
Audio Compr
The type of audio compression selected for this span. Default
means that the device is using the system-wide setting.
bbec
TEP performance data. G.826 Near End, Far End. Number of E1
background block errors.
bber
TEP performance data. G.826 Near End, Far End. Background
block ratio.
bes
TEP performance data. Bursty Errored Seconds, TR54016 Far
End and Far End. Number of seconds during which there were
2 to 319 CRC errors, but no Severely Errored Frame or AIS
conditions.
BdId
Board (card) ID number.
442
CHAPTER 18: TROUBLESHOOTING
Table 84 Configuration and Status Report Headings (continued)
Heading
Description
BdId Name
Board (card) name.
Brd
The number of the board (card) in a multiple board system.
CO Switch Protocol Protocol (ETS1, QSIG Slave) used by the CO switch (not
applicable to T1).
Card Type
Type of card (T1, ISDN PRI, E1, BRI).
Ch MAC Address
Channel MAC address.
Ch List
Channels supported by a DSP.
Ch Name
Name of a channel.
ChId
Unique identifying number of a channel in a list of channels,
possibly including channels from more than one board.
ChNo
Channel number. For example: 1–24 for a T1 board.
css
TEP performance data. Controlled Slip Seconds, TR54016 Near
End and Far End. Number of seconds of controlled (benign)
slips.
cssp
TEP performance data. Controlled Slip Seconds Path, T1.231
Near End and Far End. Number of seconds of controlled
(benign) slips.
CurState
Current state of a channel (in use, idle, available).
cv
TEP performance data. Code Violations, G.826 Near End.
Number of bipolar violations and excessive zeros.
cvl
TEP performance data. Code Violations Line, T1.231 Near End.
Number of bipolar violations and excessive zeros.
cvp
TEP performance data. Code Violations Path, T1.231 Near End
and Far End. Number of bipolar violations and excessive zeros.
datasecs
TEP performance data. The number of seconds with valid data.
DNIS/DID
Number of digits passed that identify the called party.
DSP Name
Name of a digital signal processor.
DSP Status
Status of a digital signal processor.
DSP Version
Version of code running on a digital signal processor.
Digit Collection
Specifies the data the CO sends and the format in which it is
sent over the span of an incoming call. Can include both
DNIS/DID and ANI, and can specify the order in which they
arrive, and the number of digits involved.
EchoCanceller
The state of the echo cancellation function. Values: Enabled,
Disabled.
E&M Direction
For a T1 line, the direction of the E&M signaling. Values: Two
Way, One Way. Default: Two Way.
System-level Troubleshooting
443
Table 84 Configuration and Status Report Headings (continued)
Heading
Description
ErrorCnt
Reserved for future use.
ErrorCode
Reserved for future use.
es
TEP performance data. Errored Seconds, TR54016 Near End
and Far End. Number of one-second intervals with exactly one
CRC-6 error and no SEF or AIS defects.
esap
TEP performance data. Errored Seconds Type A, T1.231 Near
End and Far End. Number of one-second intervals with exactly
one CRC-6 error and no SEF or AIS defects.
esbp
TEP performance data. Errored Seconds Type B, T1.231 Far
End. Number of one-second intervals with between 2 and 319
CRC errors.
esc
TEP performance data. Errored Seconds, G.826 Near End and
Far End. Number of one-second intervals with exactly one
CRC-6 error and no SEF or AIS defects.
esl
TEP performance data. Number of one-second interval with
between 2 and 319 CRC errors. (line)
esp
TEP performance data. Errored Seconds, T1.231 Near End and
Far End. The number of one-second intervals with between 2
and 319 CRC errors.
esr
TEP performance data. Errored seconds ratio, G.826 Near End
and Far End.
Ext.
The extension number for a channel.
fc
TEP performance data. Failure Count, T1.231 Near End and Far
End. Total failure count for the sample.
FlashHookTransfer
Status of flash hook transfer function. If enabled, allows user
receiving a call to do a flash hook transfer to another trunk line
Values: Enabled, Disabled. Default: Enabled
Framing Type
Type of framing used on this board (ES4, D4). For a T1 board,
ESF is always associated with a B8ZS line coding, and D4 is
always associated with AMI line coding.
Framer Loopback
The state of the setting for the Framer Loopback test, either
enabled or disabled.
GpId
Group ID number.
Group Name
Group name.
Guard
A time out value that controls the waiting period after a call
completes, before the channel can be used for another
outbound call from system.
InterfaceType
Type of interface. Values: E1, T1, ISDN, no config. Default: T1.
Does not apply to T1 E&M.
444
CHAPTER 18: TROUBLESHOOTING
Table 84 Configuration and Status Report Headings (continued)
Heading
Description
Interval
TEP performance statistics are sampled every 15 minutes. The
system saves up to 24-hours of data in 15-minute intervals.
Intl. Prefix
An advanced configuration setting. An identifier, up to
five-digits, that can be manually configured for outgoing calls
on this span. Manual configuration of the international prefix is
for situations where the telephone company equipment
requires special configuration on the system.
Line Code
Type of line coding used (HDB3, AMI). For a T1 board, AMI line
coding is always associated with D4 framing, and B8ZS line
coding is always associated with ESF framing.
Line Length
Length of the line between the termination and the board.
Line Loopback
The state of the setting for the Line Loopback test, either
enabled or disabled.
lofc
TEP performance data. Loss Of Frame Count, T1.231 Near End
and Far End. Number of Out-Of-Frame events.
los
TEP performance data. Loss Of Signal Seconds, G.826 Near
End. Number of seconds during which the signaling channel
was lost.
lossl
TEP performance data. Loss of Signal Seconds, T1.231 Near
End. Number of seconds during which no pulses (loss of signal)
have arrived within 100 to 250 bit times.
Local Loopback
The state of the setting for the Local Loopback test, either
enabled or disabled.
MAC Address
A 48-bit address unique to each network device.
Model Number
The model number of the board.
Values:
0x0700 — T1 board 3C10116B
0x0b00 — T1 board 3C10116C
0x0e00 — T1 board 3C10116D
0x0c00 — E1 board 3C10165C
0x0f00 — E1 board 3C10165D
0x0a00 — BRI board 3C10164C
National Prefix
An advanced configuration setting. An identifier, up to
five-digits, that can be manually configured for outgoing calls
on this span. Manual configuration of the national prefix is for
situations where the telephone company equipment requires
special configuration on the system.
NCP Conne
The amount of time that the Digital Line Card waits for the Call
Processor to connect the call.
“USER_ALERTING_NO_ANSWER” errors mean that this value
may be too small.
System-level Troubleshooting
445
Table 84 Configuration and Status Report Headings (continued)
Heading
Description
NCP Gener
A time-out value that controls how long the Digital Line Card
waits for a response from the Call Processor. Do not modify this
value.
Network Digit
A time-out value that controls how long the Digital Line Card
waits between digits sent on an incoming call.
OffHk Min
The minimum time an analog telephone, connected to an
Analog Terminal Card, must be off hook for the system to
recognize that the telephone has been picked up.
On Line
One possible status of a channel.
oof
TEP performance data. Out of Frame Seconds, G.826 Near
End. Number of seconds during which there were excessive
frame bit errors.
Payload Loopback
The state of the setting for the Payload Loopback test, either
enabled or disabled.
Prepend Prefix
Full text: Prepend prefix to Calling Party Number in Setup
Indication.
Either enabled or disabled. National and international prefixes
can be added for outgoing calls. The prefix is for situations
where the telephone company equipment requires special
configuration on the system.
Protocol
A signaling method used to make calls.
rai
TEP performance data. Remote Alarm Indicator, G.826 Near
End and Far End. Number of seconds during which a remote
alarm indication was declared.
Recv. Timer
Full Text: Overlap Receiving timer (T302).
PRI span only. An advanced configuration setting for situations
where the telephone company equipment requires special
configuration on the system.
Release Complete
Full Text: Send “Release Complete” if incoming call is from
incompatible equipment.
Either enabled or disabled. An advanced configuration setting
for situations where the telephone company equipment
requires special configuration on the system.
RxWnkMax
The maximum duration of a received Wink signal.
RxWnkMin
The minimum duration of a received Wink signal.
sasp
TEP performance data. SEF/AIS Seconds, T1.231 Near End.
Number of seconds when at least 2 frame bit errors or loss of
frame encountered.
446
CHAPTER 18: TROUBLESHOOTING
Table 84 Configuration and Status Report Headings (continued)
Heading
Description
sefsp
TEP performance data. Severely Errored Frame Seconds,
T1.231 Far End. Number of one-second intervals with either
out-of-frame signals, AIS defects, 390 or more CRC errors, or
four or more frame bit errors.
Sending Complete
Full Text: Send “Sending Complete IE” in Setup Request
IE (Information Element) refers to the data fields within an
ISDN layer 3 message. An advanced configuration setting for
situations where the telephone company equipment requires
special configuration on the system.
ses
TEP performance data. Severely errored seconds, TR54016
Near and Far End. Number of one-second intervals with either
out-of-frame signals, AIS defects, 390 or more CRC errors, or
four or more frame bit errors.
sesc
TEP performance data. Number of one-second intervals with
either out-of-frame signals, AIS defects, 390 or more CRC
errors, or four or more frame bit errors.
sesl
TEP performance data. Severely Errored Seconds Line, T1.231
Near End. Number of one-second intervals with either
out-f-frame signals, AIS defects, 390 or more CRC errors, or
four or more frame bit errors.
sesp
TEP performance data. TEP performance data. Severely Errored
Seconds Path, T1.231 Near End. Number of one-second
intervals with either out-of-frame signals, AIS defects, 390 or
more CRC errors, or four or more frame bit errors.
sesr
TEP performance data. Severely Errored Seconds Ratio, G.826
Near End and Far End.
Silence Suppr
The state of the silence suppression setting for this span.
“Default” indicates that the span is set to use the system-wide
setting.
SpId
Span ID.
SpNo
Span number.
Span MAC Address MAC address assigned to this span.
Span Name
Name of span.
SpanNo
Identifying number for a span.
Start Type
Mechanism used to indicate start of a call.
Status
Status of a channel, span, card. Values: Online, Idle, Unknown.
Default: Online
Connecting a Computer to a Serial Port
447
Table 84 Configuration and Status Report Headings (continued)
Heading
Description
Strip #
Full Text: Strip trailing # from Called Party Number in Setup
Request.
Either enabled or disabled. An advanced configuration setting
for situations where the telephone company equipment
requires special configuration on the system.
Connecting a
Computer to a
Serial Port
TEI
Terminal Equipment Identification number (of BRI board). The
telephone company may provide this number or the system
may assign it, depending on how you purchased the BRI lines.
TEP Version
The version of software running on the board.
Time Last Seen
Last time activity was recorded for this board.
Timing Mode
Internal: Timing is generated from within the Digital Line Card.
Loop: Timing is taken from the central office.
Trunk to Trunk
Whether call transfers are allowed from one trunk to another.
Values: Enabled (default), Disabled, Restricted, Unrestricted.
TxGudMin
The minimum duration of a transmitted Guard signal.
TxWnkDura
The duration of a transmitted Wink signal.
uas
TEP performance data. Unavailable Seconds, TR54016 Near
End and Far End. Number of seconds during which the frame
was unavailable for 10-seconds.
uasc
TEP performance data. Unavailable Seconds, G.826 Near End
and Far End. Number of seconds during which the frame was
unavailable for 10-seconds.
uasp
TEP performance data. Unavailable Seconds, T1.231 Near End
and Far End. Number of seconds during which the frame was
unavailable for 10-seconds.
vsecs
TEP performance data. Valid seconds for the selected interval.
Wink Wait
This time out value controls how long the Digital Line Card
waits to respond with a wink signal on an outgoing call. If you
see “no_wink_received” errors, this value may be too small.
On some devices, you can connect a computer to a serial port and, by
running a terminal-emulation program on the computer, you can obtain
information about the status of the card or the system.
448
CHAPTER 18: TROUBLESHOOTING
You can connect a computer directly to the serial port on these devices:
Table 85 Serial Port Connections
Card
Port
V3001R Call Processor
CONSOLE
V3000 Call Processor
CONSOLE
V3001 Call Processor
CONSOLE
V5000 Call Processor
COM1
NBX 100 Call Processor
COM1
BRI-ST Digital Line Card
CONSOLE
E1 Digital Line Card
CONSOLE
T1 Digital Line Card
CONSOLE
Analog Line Card (3C10114C only)
CONSOLE
Analog Terminal Card (3C10117C only)
CONSOLE
It does not matter which computer operating system you use. As long as
the computer has a terminal-emulation program that can emulate a
VT100 terminal (for example, Microsoft Hyperterminal), it can
communicate with any of the cards listed in Table 85.
To connect the computer to the COM1 or CONSOLE port on a board:
1 Using a standard computer serial cable (9-pin male to 9-pin female),
connect the male end of the cable to the female connector (COM1 or
CONSOLE) on the front panel of the board.
2 Connect the female end of the cable to an available serial port on the
computer.
3 Start the terminal-emulation software and create a new connection.
4 Configure the connection to use the serial port to which you connected
the cable and to use the settings in Table 86.
Table 86 Terminal-Emulation Program Properties
Property
Value
Emulation
VT100
Baud Rate
9600
Data bits
8
Parity
None
Stop bits
1
Servicing the Network Call Processor Battery
449
Table 86 Terminal-Emulation Program Properties (continued)
Property
Value
Flow control
None
All messages associated with the board (for example, the initialization
process) appear in the terminal-emulation window.
Servicing the
Network Call
Processor Battery
If you lose the system date and time when you reboot the system, it could
mean that the Call Processor battery must be replaced. The battery is not
a user-serviceable item. If you suspect a problem with the battery, contact
your 3Com Technical Support representative.
WARNING: There is a danger of explosion if the battery is incorrectly
replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Getting Service and
Support
Your authorized 3Com NBX Voice-Authorized Partner can assist you with
all your support needs, including systems and cable plant design,
installation, configuration, and project management.
A choice of maintenance services, including remote diagnostics, on-site
support, telephone technical support, and hardware replacement, is
available from your 3Com NBX Voice-Authorized Partner. Training and
enhancement services are also available.
450
CHAPTER 18: TROUBLESHOOTING
A
INTEGRATING THIRD-PARTY
MESSAGING
The system can operate with a third-party messaging system. This
appendix describes the steps that you must perform to use a third-party
messaging system with the system:
■
Installing Software on the Third-Party Messaging Server
■
Configuring the System
■
Configuring NBXTSP on the Server
If you are using the 3Com IP Messaging Module with a SIP -mode system,
do not follow the instructions in this chapter. See the IP Messaging
Module Installation Guide, which is available through the NBX NetSet
utility (click Downloads > Documentation).
Installing Software
on the Third-Party
Messaging Server
You must install the NBX Media Driver and the NBX TAPI Service Provider
(NBXTSP) on the third-party messaging server to enable it to interact with
the system. See your messaging application’s documentation for server
requirements.
1 Install the NBX Media Driver application from the NBX Resource Pack
DVD or the NBX Partner Access web site.
2 Install the NBXTSP software from the NBX Resource Pack DVD or the NBX
Partner Access web site.
You can also download the NBXTSP software from your system by
connecting to the NBX NetSet utility from a browser located on the
third-party messaging server.
452
APPENDIX A: INTEGRATING THIRD-PARTY MESSAGING
Configuring the
System
To activate third-party messaging on the system use the NBX NetSet utility
to perform the tasks described in this section. All NetSet procedures
require an administrator login.
1 Add the Third-party Messaging and Media Driver licenses to your system:
a Click Licensing and Upgrades > Licenses > Add License.
b In the License Key field, enter the license key provided by your 3Com
Voice-Authorized Partner.
c Click Apply.
d Add any additional licenses. When you are finished adding licenses,
click OK.
e Reboot the system.
3Com strongly recommends that you back up your licenses each time you
make a license change.
2 Verify that Auto Discover Telephones is enabled:
a Click System-Wide Settings > Auto Discovery.
b Verify that Auto Discover Telephones is enabled.
c Click Apply.
3 Verify that NBX Messaging is disabled:
a Click System-Wide Settings > Enable Features System-Wide.
b Verify that NBX Messaging is disabled.
c Click Apply.
4 Create a Hunt Group for the third-party messaging system:
a Select Call Distribution Groups > Hunt Groups > Add.
b Set the following parameters:
■
Name — UM Hunt Group (or some similar name).
■
Type — HuntGroup - Circular.
3Com recommends that you use a circular hunt group.
■
Extension — Enter the appropriate extension for your hunt group.
■
Password — Set the password for this hunt group.
■
Logout if no answer — Verify that this check box is empty.
Configuring NBXTSP on the Server
■
Users — Select the WAV phones and the ATA ports that are
connected to the third-party messaging system.
■
Call Coverage — Set to voice mail.
453
c Click Apply.
5 Modify the Voice Mail Extensions List:
1 Click Dial Plan > Extension Lists.
2 Click *0003 VoiceMail to display the Modify window.
3 To add a voice mail extension, use the Membership list:
a If the list does not include any voice mail extensions, click the check
boxes next to the voice mail extension that you want to add to the list.
b If the list already has members, click Show all to display a list of voice
mail extensions that you can add to the membership.
Note: You can toggle between the Show all and Show members only
buttons to display voice mail extensions that have membership in the list
and the voice mail extensions that are not members of the list but which
you can add to the list, and to confirm your changes.
4 Click OK.
Configuring
NBXTSP on the
Server
On the third-party messaging server, you must add the WAV extensions
to the NBX TAPI Control Panel. If your third-party messaging system
needs TAPI messages from Analog Terminal Adapter devices or 3Com
telephones, you must also add these devices to the NBX TAPI Control
Panel.
Update the devices in the NBX TAPI Control Panel:
1 WinNT — On the server, select Control Panel > Telephony >
Telephony Drivers > NBX TAPI Service Provider.
Win2K — On the server, select Control Panel >
Phone and Modem Options > Advanced > NBX TAPI Service Provider.
2 Click Configure and add the extension numbers.
3 Click OK.
You are now ready to install your third-party messaging software. See
your application’s documentation for installation and configuration
instructions.
454
APPENDIX A: INTEGRATING THIRD-PARTY MESSAGING
ISDN COMPLETION CAUSE CODES
B
This appendix lists the Completion Cause Codes displayed in the Digital
Line Card span Status windows.
To access the Status window:
1 Click the appropriate link:
■
PSTN Gateway Configuration > T1 Spans.
■
PSTN Gateway Configuration > ISDN PRI Spans.
■
PSTN Gateway Configuration > ISDN BRI Spans.
2 Click a span’s state to display the Status window.
Table 87 lists the codes that detail the reasons for the termination of a
call. Also, see “Configuring and Managing Digital Line Cards” on
page 164 for more information.
These completion cause code descriptions are only guidelines.
The detailed cause may vary according to the Public Switched Telephone
Network (PSTN) to which your system is connected.
Table 87 Completion Cause Codes
Hex
Class Grouping Code
Decimal
Code
Description
Normal events
0x00
0
No diagnostic
0x01
1
Unassigned
number
The requested destination, although valid, cannot be
reached.
0x02
2
No route
The sending equipment (sending the cause) is requested to
route the call through an unrecognized transit network.
0x03
3
No route to
destination
The called user cannot be reached because the network
does not serve the destination.
0x06
6
Channel
unacceptable
The last identified channel is not acceptable to the sending
entity.
Details
456
APPENDIX B: ISDN COMPLETION CAUSE CODES
Table 87 Completion Cause Codes (continued)
Hex
Class Grouping Code
Resource
unavailable
Decimal
Code
Description
Details
0x07
7
Call awarded
The incoming call is connected to a channel already
established for similar calls (for example, packet-mode X.25
virtual calls).
0x10
16
Normal
clearing
This call is being cleared by one of the users involved.
0x11
17
User busy
The called user cannot accept another call although
compatibility is established.
0x12
18
No user
responding
The user does not respond to call establishment messages
with either an alerting or connect indication within the
allowed time.
0x13
19
User alerting
no answer
The user has provided an alerting indication but no connect
indication within the allowed time.
0x15
21
Call rejected
Equipment sending the cause does not accept this call
although it is not busy or incompatible.
0x16
22
Number
changed
The called party number is not assigned.
0x1A
26
Non-selected
user clearing
The user has not been awarded the incoming call.
0x1B
27
Destination out The destination interface is not operating correctly.
of order
0x1C
28
Invalid number The called party number is invalid, or incomplete.
format
0x1D
29
Facility rejected The network cannot provide the facility requested.
0x1E
30
Response to
status enquiry
The reason for the STATUS message was the prior receipt
of a STATUS ENQUIRY message.
0x1F
31
Unspecified
cause
Used to report normal events only when no other cause in
the normal class applies.
0x22
34
No circuit
available
An appropriate circuit or channel is not currently available
to manage the call.
0x23
35
Call queued
(AT&T)
The network is not functioning. Immediate redial is unlikely
to be successful.
0x26
38
Network out of The network is not functioning. Immediate redial is unlikely
order
to be successful.
0x29
41
Temporary
failure
The network is not functioning. Immediate redial is unlikely
to be successful.
0x2A
42
Network
congestion
The switching equipment generating this cause is
experiencing a period of high traffic.
457
Table 87 Completion Cause Codes (continued)
Hex
Class Grouping Code
Decimal
Code
Description
Details
0x2B
43
Access info
discarded
The network could not deliver access information to the
remote user as requested. May include the type of
discarded information (user-to-user information, low layer
or high layer compatibility, or sub-address).
0x2C
44
Requested
channel not
available
Returned when the circuit (or channel) indicated by the
requesting entity cannot be provided by the other side of
the interface.
0x2D
45
Pre-empted
0x2F
47
Resources
unavailable –
unspecified
Reports a resource unavailable event only when no other
cause in the resource unavailable class applies.
Service or option 0x31
not available
49
Quality of
service
unavailable
Throughput or transit delay cannot be supported and that
the Quality of Service (as defined in Recommendation
X.213) cannot be provided.
0x32
50
Facility not
subscribed
The requested supplementary service could not be provided
by the network because the user has not completed the
necessary administrative arrangements with its supporting
networks.
0x34
52
Outgoing call
barred
0x36
54
Incoming call
barred
0x39
57
Bearer
capability not
authorized
The user is trying to make unauthorized use of equipment
providing a bearer capability.
0x3A
58
Bearer
capability not
available
The user has requested a bearer capability, which is
implemented by the equipment generating the cause, but
is not available at this time.
0x3F
63
Service not
available
Reports a service (or option) not available event only when
no other cause in the service (or option) not available class
applies.
Service or option 0x41
not implemented
65
Capability not
implemented
The equipment sending this cause does not support the
requested bearer capability.
0x42
66
Chan not
implemented
The equipment sending this cause does not support the
requested channel type.
0x45
69
Facility not
implemented
The equipment sending this cause does not support the
requested supplementary service.
0x46
70
Only restricted One equipment has requested an unrestricted bearer
digital available service but the equipment sending this cause only supports
the restricted version.
458
APPENDIX B: ISDN COMPLETION CAUSE CODES
Table 87 Completion Cause Codes (continued)
Hex
Class Grouping Code
Invalid message
Protocol error
Decimal
Code
Description
Details
0x4F
79
Service not
implemented,
unspecified
Reports the service (or option) not implemented event only
when no other cause in the service (or option) not
implemented class applies.
0x51
81
Invalid call
reference
The equipment sending this cause has received a message
with a call reference that is not currently in use on the user
network interface.
0x52
82
Chan does not
exist
The equipment sending this cause has received a request to
use a channel that is not activated on the interface for a
call.
0x53
83
Suspended call A call resume has been attempted with a call identity that
exists, call
differs from that in use for any currently suspended calls.
identity does
not
0x54
84
Call identity in
use
0x55
85
Incompatible
destination
0x58
88
Incompatible
destination
0x5B
91
Transit network
does not exist.
0x5F
95
Invalid message Reports an invalid message event only when no other cause
(unspecified)
in the invalid message call applies.
0x60
96
Mandatory IE
missing
The equipment sending this cause has received a message
that is missing an information element that must be present
in the message before that message can be processed.
0x61
97
Nonexistent
message
The equipment sending this cause has received a message
with a message type that it does not recognize, either
because it is an undefined message, or it is defined but not
implemented by the equipment sending the cause.
0x62
98
Wrong
message
The equipment sending this cause has received a message
that it considers as not permitted while in the call state; or a
STATUS message was received indicating an incompatible
call state.
The network has received a call suspended request that
contained a call identity (including the null call identity) that
is already in use for a suspended call within the domain of
interfaces over which this call may be resumed.
The equipment sending this cause has received a request to
establish a call that has low layer compatibility, high layer
compatibility, or other compatibility attributes (for example,
data rate) that cannot be managed.
459
Table 87 Completion Cause Codes (continued)
Hex
Class Grouping Code
Interworking
Decimal
Code
Description
Details
The equipment sending this cause has received a message
that includes information elements not recognized because
the information element identifier is not defined, or it is
defined but not implemented by the equipment sending
the cause. However, the information element is not
required to be present in the message to enable the
equipment sending the cause to process the message.
0x63
99
Bad info
element
0x64
100
Invalid element The equipment sending this cause has received an
contents
information element that it has implemented. However, the
sending equipment was not able to implement the code
because one or more of the fields were incorrectly coded.
0x65
101
Wrong
message for
state
The received message is incompatible with the call state.
0x66
102
Timer expiry
A timer has expired and an associated Q.931 error handling
procedure has been initiated.
0x67
103
Mandatory IE
length error
0x6F
111
Protocol error
Reports an error event only when no cause in the protocol
error class applies.
0x7F
127
Interworking
unspecified
There has been interworking with a network that does not
provide cause codes for its actions. Therefore, the precise
cause for a message being sent is not known.
460
APPENDIX B: ISDN COMPLETION CAUSE CODES
C
Overview
CONFIGURING OPTION 184 ON A
WINDOWS 2000 DHCP SERVER
RFC 2132 (DHCP Options and BOOTP Vendor Extensions) allows for
vendor-specific extensions to the DHCP protocol. It defines that option
codes in the range 128 through 254 are set aside for site-specific
extensions.
3Com telephones can receive their IP configuration from a DHCP server.
However, 3Com telephones need configuration information that is not
part of a standard DHCP response. You can use DHCP option 184 to
specify this extended information:
■
NCP IP Address — Each telephone must receive a download of
operating settings from the Call Processor.
■
Alternate Server IP Address — Specifies a second location from which
a telephone can receive its download. (Not used in an NBX system.)
■
Voice VLAN Configuration — Reserved for future use.
■
Fail-Over Call Route Point — Reserved for future use.
This appendix includes an example of how to configure option 184 on a
Windows 2000 server that has been configured to run DHCP server
software. It describes these topics:
■
Creating Option 184
■
Editing Option 184 Values
■
Activating Option 184
This appendix describes how to configure the Call Processor IP address
only. The extended options are not used in an NBX environment. The
information in this appendix pertains only to a Windows 2000 server. The
configuration instructions differ for other DHCP servers. This appendix
describes only the configuration of option 184, not how to install or
perform basic configuration of the Windows 2000 server.
462
APPENDIX C: CONFIGURING OPTION 184 ON A WINDOWS 2000 DHCP SERVER
Creating
Option 184
If you are configuring more than one subfield for Option 184, the first
subfield must be the Call Processor IP Address for backward compatibility.
1 Start the DHCP Microsoft Management Console:
Start > Programs > Administrative Tools > DHCP
The DHCP dialog box appears. In the left pane, look for the name of your
Windows 2000 DHCP server.
2 Right click the name of your DHCP server. From the menu that appears,
select Set Predefined Options to open the Predefined Options and Values
dialog box.
3 Click Add to open the Option Type dialog box.
4 In the Name field, type a name of your choice.
5 From the Data Type drop-down list, select Byte.
6 Enable the Array check box.
7 In the Code field, type 184.
8 In the Description field, enter a description of your choice. Example: NBX
NCP IP Address.
9 Click OK.
In the Predefined Options and Values dialog box, the DHCP Microsoft
Management Console creates a new option name by combining the
option number with the name that you chose and adds this name to the
Option name drop-down list. Example: If you used NBX as the option
name, the system adds 184 NBX to the drop-down list.
Editing Option 184
Values
1 Select the new option name from the Option name drop-down list, and
click Edit Array. The Numeric Value Array Editor dialog box appears.
2 In the Data entry area of the dialog box, click the Decimal radio button at
the right of the word Format.
3 In the Current Values field, highlight the 0 (zero), and click Remove.
4 To create the new value, enter each element of the new value:
a Click in the New value field.
b Type the individual element value.
Activating Option 184
463
c Click Add.
5 Repeat steps 4 a, b, and c for each element in the following table. As you
add each element, it appears in the Current values list, above previously
added values.
Add these elements in this order:
Table 88
What You Type
Description
1
Enter 1 as the only suboption code for option 184. (Some
options can have more than one suboption.)
4
The length of the argument that applies to this suboption.
For option 184, suboption 1, the argument is an IP address,
which is composed of four numerical fields (octets).
NOTE: The next four fields use 10.234.1.254 as the sample IP address of the Call
Processor. Enter the IP address of your Call Processor.
10
The first octet in the IP address of the Call Processor.
234
The second octet in the IP address of the Call Processor.
1
The third octet in the IP address of the Call Processor.
254
The fourth octet in the IP address of the Call Processor.
6 After you have entered all elements in the new value, click OK. You return
to the Predefined Options and Values dialog box. The values that you
entered appear in the Value area of the dialog box under Byte.
The values appear in hexadecimal format although you entered them in
decimal format.
7 To accept the values, click OK. You return to the DHCP Microsoft
Management Console dialog box.
Activating Option
184
To activate option 184, decide whether you want to apply the option to a
specific scope or globally, that is, to all scopes that are served by the
DHCP server software.
To activate option 184 for a specific scope:
1 In the left pane of the DHCP Microsoft Management Console dialog box,
find the scope that you want. Then highlight Scope Options.
2 Right click Scope Options, and, from the menu that appears, select
Configure Options. The Scope Options dialog box appears.
464
APPENDIX C: CONFIGURING OPTION 184 ON A WINDOWS 2000 DHCP SERVER
3 Scroll down in the Available Options list until you find the option that you
just added (184 NBX in this example).
4 Enable the check box to the left of the option.
5 Click OK.
In the right pane, the option name now appears in the Option Name
column. The Vendor column contains the word Standard. The values of
the individual elements that you entered appear in the Value column.
The values appear in hexadecimal format although you entered them in
decimal format.
To activate option 184 globally:
1 In the left pane of the DHCP Microsoft Management Console dialog box,
highlight Server Options.
2 Right click Server Options, and from the menu that appears, select
Configure Options. The Server Options dialog box appears.
3 Scroll down in the Available Options list until you find the option that you
just added (184 NBX in this example).
4 Enable the check box to the left of the option.
5 Click OK.
In the right pane, the option name now appears in the Option Name
column. The Vendor column contains the word Standard. The values of
the individual elements that you entered appear in the Value column.
The values appear in hexadecimal format although you entered them in
decimal format.
D
CALLER ID
If you are set up to receive Caller ID services from your telephone
company, the NBX system propagates the Caller ID information that is
received from the telephone company to the final destination of the call
even when that call is forwarded manually or through an auto attendant.
Some Caller ID behavior varies depending on the type of device and the
conditions under which the call is received. This appendix describes these
caller ID conditions:
Forwarded Calls
and Caller ID
■
Forwarded Calls and Caller ID
■
Long Caller ID Character Strings
■
Specific Caller ID Situations
While a forwarded call is ringing on a telephone:
■
The top line in the telephone’s display panel shows the Caller ID of the
original caller and a greater than (>) character on the left side of the
display helps you to visually identify the Caller ID of the original caller.
■
The bottom display panel line shows the Caller ID of the telephone
that is performing the transfer.
After the call is answered, only the Caller ID of the original caller remains
in the display and the greater than (>) character is removed.
Calls That Are
Forwarded Multiple
Times
If a call is forwarded several times, the Caller ID information of the
original caller appears on the top line of the display panel of the ringing
telephone and the Caller ID of the telephone that most recently
forwarded the call appears on the bottom line. A greater than (>)
character appears to the left of the original Caller ID on the top line in the
telephone display panel.
Example: A places a call to B, who answers the call and forwards it to C,
whose telephone is forwarded to D. While telephone D is ringing, the top
466
APPENDIX D: CALLER ID
line in the display panel contains the Caller ID for A and the bottom line
contains the Caller ID for C. After 5 seconds, only the Caller ID
information for A appears.
Long Caller ID
Character Strings
Some older models of the 3Com Business Telephone can display two lines
of 16 characters while newer models of the 3Com Business Telephone
can display two lines of 24 characters. The displays of different brands
and models of analog telephones with built-in Caller ID typically can
show either 16 or 24 characters for each line. The same is true of Caller
ID boxes that are connected in-line with analog telephones.
If the length of the Caller ID information on either the top or bottom line
exceeds the width of the telephone display panel, the information is
truncated for the first five seconds. After five seconds, the Caller ID
information on the bottom line is cleared, and any truncated information
from the top line appears on the bottom line. After an additional five
seconds, if the Caller ID information from the top line exceeds the
capacity of both display lines, the numeric portion is removed and only
the name appears in the display.
Specific Caller ID
Situations
Analog Terminal
Adapter and Analog
Terminal Card Ports
The Caller ID information that appears on the telephone display panel can
be different in some specific call situations.
If you have an analog telephone connected to the system using a single
port Analog Terminal Adapter, to a port on an Analog Terminal Card, or
to a port on the front of an NBX platform, the behavior of Caller ID on
the analog telephone (or on Caller ID boxes connected in-line with the
analog telephone) depends on whether the Caller ID device/telephone
supports 2-line Caller ID display.
■
Most analog telephones with built-in Caller ID and most Caller ID
boxes do not support 2-line display of Caller ID information. For this
type of device, only the Caller ID of the original caller appears.
■
If the analog telephone or Caller ID box supports 2-line display of
Caller ID information, the information appears in the same way as it
does on an 3Com telephone.
If the Caller ID information exceeds the capacity of the Caller ID display
(some can display 16 characters and others can display 24 characters) the
Caller ID information is typically truncated at the width of the display.
Specific Caller ID Situations
3Com Legacy Link or
Citel Analog
Interface Card
Bridged Extension
Telephones
External Calls
467
If you have analog telephones connected to the system using the 3Com
Legacy Link or Citel analog interface card, the behavior of Caller ID on the
analog telephones is the same as the behavior of analog telephones
connected to a single port Analog Terminal Adapter or a port on an
Analog Terminal Card. See “Analog Terminal Adapter and Analog
Terminal Card Ports” on page 466.
Caller ID information appears in exactly the same way on a bridged
extension telephone as it does on a non-bridged extension telephone.
See “Caller ID” on page 465 and “Long Caller ID Character Strings” on
page 466.
The display of Caller ID information for external calls depends on how the
call arrives at the system.
External Analog Line Card Calls
An external call arrives at a system on an Analog Line Card port and is
routed to A’s telephone.
When A transfers the call to B, the Caller ID (if any is provided by the
telephone company) appears in the top line of B’s telephone display
panel. If no Caller ID information is available, the extension associated
with the Analog Line Card port appears on the top line. A’s Caller ID
information appears in the bottom line.
Exception: An Analog Line Card port is mapped to an internal extension.
The call is not answered and goes to the call coverage point for the
extension. If the coverage point is the receptionist’s telephone, for
example, the receptionist sees the Caller ID information for the external
call, and not for any telephone on which the mapped Analog Line Card
Port appears.
External ISDN BRI Calls
An external call arrives at a system on an ISDN BRI channel and is routed
to A’s telephone.
When A transfers the call to B, the Caller ID (if any is provided by the
telephone company) appears for five seconds in the top line of B’s
telephone display panel. If no caller ID information is available, the Trunk
468
APPENDIX D: CALLER ID
name and channel number from the Digital Line Card appear on the top
line of B’s telephone display panel. A’s ID appears on the bottom line.
External ISDN PRI Calls
An external call arrives at a system on an ISDN PRI channel and is routed
to A’s telephone.
When A transfers the call to B, the Caller ID (if any is provided by the
telephone company) appears for five seconds in the top line of B’s
telephone display panel. If no caller ID information is available, the Trunk
name and channel number from the Digital Line Card appear on the top
line of B’s telephone display panel. A’s ID appears on the bottom line.
External T1 Calls
An external call arrives at a system on a T1 channel and is routed to
telephone A. If the call is transferred to B, the display of caller ID
information on B’s telephone depends on which Incoming Call Digit
Format is configured on the T1 board.
■
DNIS/DID — The T1 board is configured to expect either Dialed
Number Identification System digits or Direct Inward Dialing digits.
If DNIS digits arrive, there is no Caller ID information. Instead, the
system displays the name of the T1 trunk and the extension associated
with the T1 channel.
■
DNIS/ANI — The T1 board is configured to expect Dialed Number
Identification System digits followed by Automatic Number
Identification digits.
The system displays the ANI portion of the incoming digit sequence
followed by the name of the T1 trunk and the extension associate
with the T1 channel. The ANI field can be configured to capture either
7 or 10 digits of ANI information.
Internal Calls
On a single system, user A calls B who transfers the call to user C. In C’s
telephone display panel, the top line contains Caller ID information for A
and the bottom line contains Caller ID information for B.
Nortel Phones
If you have Nortel telephones connected to your system using the Nortel
interface card, the behavior of Caller ID on these telephones is identical
to the behavior on 3Com telephones.
Specific Caller ID Situations
Parked Calls
469
When you retrieve a parked call, the Caller ID associated with the call
appears for approximately five seconds in your telephone display panel.
You do not see the Caller ID of the person who parked the call.
Second Incoming Call
If you are currently involved in a call on your telephone and another call
arrives, for approximately five seconds you see “Incoming Call” on the
top line of the telephone display panel and the Caller ID of the incoming
call appears on the bottom line.
TAPI Calls
If a call is forwarded to a telephone that is controlled by TAPI software,
both the original Caller ID and the Caller ID of the person forwarding the
call are sent to the TAPI software.
TAPI Redirected Calls
If telephone A is being monitored by an external TAPI application and a
forwarded call to A is redirected to telephone B, the TAPI software passes
the Caller ID of the original caller and the Caller ID of the forwarding
telephone to telephone B.
VTL Calls
If A1 calls A2 who then forwards the call to B1 over a Virtual Tie Line
connection, the Caller ID information for A2 appears in the display panel
on B1’s telephone. The Caller ID information includes the IP address of
System A and the extension number of A2.
See “Adding VTL Devices to the Pretranslators (Optional)” on page 343
for information about how to remove the IP address from the Caller ID
information or change it to the VTL site code for that site.
Calls Transferred to
Hunt Groups
When someone performs a blind transfer to a hunt group, telephones in
the hunt group show the Caller ID information of the original caller on
line 1 and the hunt group name and number on line 2. After a hunt
group member answers the call, only the Caller ID information of the
original caller appears.
3Com Cordless Calls
The 3Com Cordless handset shows DTMF entries that briefly start from
the bottom right hand corner of the display, then shift to standard screen
placement. This behavior is normal for this telephone.
470
APPENDIX D: CALLER ID
E
OUTBOUND CALLER ID AND 911
SERVICE
This dial plan example allows the DID number of any user on a system to
be presented as an outbound Caller ID when that user dials 911. When
the user makes any other type of outbound call, the Caller ID presented is
the main number of the site.
To accomplish this:
1 Create a new extension list and assign as many PRI channels as there are
devices to have a sufficient number for potential 911 calls.
3Com strongly recommends that you use the highest-numbered channels
for the 911 calls. The channels that you put in this list must be removed
from the *0002 extension list to ensure that channels are available for
emergency calls.
The example in this appendix uses Ext List *0011 and Route 11.
2 When you have customized and imported your dial plan (see the example
in the section), click Dial Plan > Pretranslators and then select Outbound
Caller ID for non-911 Calls and click Devices Using CLI.
3 Select only the channels in *0002.
These are the channels that the system will use for non-911 calls.
4 Click Dial Plan > Pretranslators and then highlight Outbound Caller ID for
911 Calls and click Devices Using CLI.
5 Select only the channels that the system will use for 911 calling.
These will be the same channels as those designated in Ext List *0011.
472
APPENDIX E: OUTBOUND CALLER ID AND 911 SERVICE
Sample Dial Plan
Internal 3-Digit
Extensions
Examine the sample dial plan in the rest of this appendix to learn the
customized lines that deviate from the default dial plan.
This portion of the dial plan shows the 3-digit dial plan configuration.
Table Create 1 Internal 3 Digit Extensions
/
Id Entry Digits
Min Max Class
/
-- ----- ------------ --- --- ------------TableEntry Create 1
1
0
1
1
Internal
TableEntry Create 1
2
1
3
3
Internal
TableEntry Create 1
3
2
3
3
Internal
TableEntry Create 1
4
3
3
3
Internal
TableEntry Create 1
5
4
3
3
Internal
TableEntry Create 1
6
5
3
3
Internal
TableEntry Create 1
7
6
3
3
Internal
TableEntry Create 1
8
7
3
3
Diagnostics
TableEntry Create 1
9
9
8
8
Local
TableEntry Create 1
10
90
2
64 Operator
TableEntry Create 1
11
901
4
64 International
TableEntry Create 1
12
91
9
12 LongDistance
TableEntry Create 1
13
9101
9
64 AlternateLong
TableEntry Create 1
14
911
3
3
Emergency
TableEntry Create 1
15
91800
12 12 TollFree
TableEntry Create 1
16
91888
12 12 TollFree
TableEntry Create 1
17
91877
12 12 TollFree
TableEntry Create 1
18
91900
12 12 Toll
TableEntry Create 1
19
91976
12 12 Toll
TableEntry Create 1
20
9911
4
4
Emergency
TableEntry Create 1
21
9411
4
4
Operator
TableEntry Create 1
22
9*
4
4
COCode
Incoming DID Section
Prio Route
---- ----0
4
0
0
0
0
0
0
0
0
0
3
0
0
0
0
0
1
0
1
0
1
0
1
0
1
0
11
0
1
0
1
0
1
0
1
0
1
0
11
0
1
0
1
This portion of the dial plan shows the Direct Inward Dialing and Auto
Attendant configuration.
Table Create 2 Incoming DID
/
Id Entry
/
-- ----TableEntry Create 2
1
TableEntry Create 2
2
TableEntry Create 2
3
TableEntry Create 2
4
TableEntry Create 2
5
TableEntry Create 2
6
and Auto Attendant
Digits
Min Max
------------ --- --0
1
1
1
3
3
2
3
3
3
3
3
4
3
3
5
3
3
Class
------------Internal
Internal
Internal
Internal
Internal
Internal
Prio Route
---- ----0
4
0
0
0
0
0
0
0
0
0
3
Sample Dial Plan
Least Cost Routing
Portion
This portion of the dial plan shows the Least Cost Routing configuration.
Table Create 3 Least Cost Routing
///////////////////////////////////////////////////////////////////////////
////// /
Routes
///////////////////////////////////////////////////////////////////////////
/
/
DestinationRoute
DestinationRoute
DestinationRoute
DestinationRoute
DestinationRoute
DestinationRoute
DestinationRoute
DestinationRoute
Create
Create
Create
Create
Create
Create
Create
Create
/
/
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
DestinationRouteEntry
473
Route
----1
2
3
4
6
7
8
11
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
/
/
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
DestinationRouteOperation
Description
----------LocalCO
LocalCONoStrip
Voice Application
Attendant
Virtual Tie Line (VTL) Ports
Reserved
8 Pool
Route for 911
Route Entry DestinationExtension
----- ----- -------------------1
1
*0002
1
2
*0001
2
1
*0001
3
1
*0003
4
1
*0004
5
1
*0005
6
1
*0006
7
1
*0003
8
1
*0008
11
1
*0011
Create
Create
Create
Create
Route Entry OperId Operation
----- ----- ------ --------1
1
1
stripLead
1
2
1
stripLead
8
1
1
stripLead
11
1
1
replace
Value
----1
1
1
911
474
APPENDIX E: OUTBOUND CALLER ID AND 911 SERVICE
Pretranslators (Part 1)
This portion of the dial plan shows the first part of the Pretranslators
configuration.
///////////////////////////////////////////////////////////////////////////
////// /
Pretranslators
///////////////////////////////////////////////////////////////////////////
PreTranslator Create 1 4Digit DDI 3Digit
/
PreTransId Entry
/
---------- ----PreTranslatorEntry Create
1
1
PreTranslatorEntry Create
1
2
PreTranslatorEntry Create
1
3
PreTranslatorEntry Create
1
4
PreTranslatorEntry Create
1
5
PreTranslatorEntry Create
1
6
PreTranslatorEntry Create
1
7
PreTranslatorEntry Create
1
8
PreTranslatorEntry Create
1
9
PreTranslatorEntry Create
1
10
Internal
Digits
-----1
2
3
4
5
6
7
8
9
0
PreTranslator Create 2 Outbound Caller ID for non-911 Calls
/
PreTransId Entry Digits
/
---------- ----- -----PreTranslatorEntry Create
2
1
1
PreTranslatorEntry Create
2
2
2
PreTranslatorEntry Create
2
3
3
PreTranslatorEntry Create
2
4
4
PreTranslator Create 3 Outbound Caller ID for 911 Calls
/
PreTransId Entry Digits
/
---------- ----- -----PreTranslatorEntry Create
3
1
1
PreTranslatorEntry Create
3
2
2
PreTranslatorEntry Create
3
3
3
PreTranslatorEntry Create
3
4
4
Sample Dial Plan
Pretranslators (Part2)
/
/
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
PreTranslatorOperation
475
This portion of the dial plan shows the second part of the Pretranslators
configuration.
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
Create
PreTransId Entry OperId Operation
---------- ----- ------ --------1
1
1
stripLead
1
2
1
stripLead
1
3
1
stripLead
1
4
1
stripLead
1
5
1
stripLead
1
6
1
stripLead
1
7
1
stripLead
1
8
1
stripLead
1
9
1
stripLead
1
10
1
stripLead
2
1
1
replace
2
2
1
replace
2
3
1
replace
2
4
1
replace
3
1
1
prepend
3
2
1
prepend
3
3
1
prepend
3
4
1
prepend
Value
----1
1
1
1
1
1
1
1
1
1
5083232000
5083232000
5083232000
5083232000
5083232
5083232
5083232
5083232
476
APPENDIX E: OUTBOUND CALLER ID AND 911 SERVICE
F
NBX ENTERPRISE MIB
This appendix shows the NBX Enterprise MIB, which defines the MIB
objects that have a proprietary purpose on the system.
NCP refers to the Call Processor.
***********************************************************************************
-- *
-- *
Copyright (c) 2003 by 3Com Corporation.
-- *
All Rights Reserved.
-- *
-- *
-- *
$Revision: 0.02 $
-- *
$Date: 11/08/2005
$
-***********************************************************************************
A3COMNBX-MIBDEFINITIONS ::= BEGIN
-- All definitions within this MIB are derived from the IANA assigned enterprise
-- which is declared under the enterprises node defined in the SNMP SMI.
IMPORTS
a3comNbxMIB
FROM A3Com-products-MIB
-- Import the ENTITY mib for showing the NBX hardware and software
versions,Serial Number.
entPhysicalIndex,entPhysicalName
FROM ENTITY-MIB
PhysAddress, DisplayString
FROM SNMPv2-TC
DisplayString, ipAdEntAddr
FROM RFC1213-MIB
enterprises, MODULE-IDENTITY, OBJECT-TYPE, Integer32, IpAddress,
NOTIFICATION-TYPE, Counter32
FROM SNMPv2-SMI;
478
APPENDIX F: NBX ENTERPRISE MIB
nbxMODULE-IDENTITY
LAST-UPDATED"200603281714Z"-- mar 28 2006.
ORGANIZATION"3Com"
CONTACT-INFO"Postal: 350 Campus Drive
Marlborough, MA 01752-3064
phone: 508-323-5000
fax: 508-323-1111"
DESCRIPTION"The Module is meant to describe and store the information about
the various objects that are defined for the Network business
exchange
(NBX) box. This module includes the device information and the
statistics
that are maintained by the NBX. These statistics include the
information on
the Licenses added, IP and Qos Settings etc."
REVISION"200511081714Z"
DESCRIPTION""
::= { a3comNbxMIB 1 }
-- This MIB defines 3 groups that provide for the control and monitoring
-- of all parts of an NBX system and one group for notifications.
nbxCallProcessorOBJECT IDENTIFIER
::= { nbx 1 }
nbxGatewayOBJECT IDENTIFIER
::= { nbx 2 }
nbxPhoneOBJECT IDENTIFIER
::= { nbx 3 }
nbxNotificationsOBJECT IDENTIFIER
::= { nbx 4 }
------
The Call Processor Group
Implementation of this group is mandatory for all systems
The serial num, part number, SW version, HW version for the NCP
will be provided by the entity mib (rfc-2737) instead of creating a
private mib for it. Interface info on the NCP is provided by MIB-2.
ncpSettingsOBJECT IDENTIFIER
::= { nbxCallProcessor 1
}
ncpIPModeSettingsOBJECT-TYPE
SYNTAX INTEGER {
layer2Only ( 1 ) ,
479
layer3Only ( 2 ) ,
iponFly ( 3 )
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP operating mode for connected NBX devices"
::= { ncpSettings 1 }
-- The QOS settings group is required. These settings are not yet finalized, but
placed here
-- for the completeness of the document. Incase these are not available, these
-- will be removed
ncpQosSettingsOBJECT IDENTIFIER
::= { ncpSettings 2 }
-- Provided the stats items as a table indexed by the 'entPhysicalIndex'
-- from the entity MIB. This way if we have a two board system we can show
-- these statistics for each.
ncpTableOBJECT-TYPE
SYNTAXSEQUENCE OF NcpEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"The Table consisit of one row for each NCP board available in the
NBX System."
::= { nbxCallProcessor 2 }
ncpEntryOBJECT-TYPE
SYNTAXNcpEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an Entry for each NCP in the NCP table."
INDEX { entPhysicalIndex }
::= { ncpTable 1 }
NcpEntry ::= SEQUENCE {
ncpNumberOfActiveCalls Integer32,
ncpIncomingVTLCallFailures Counter32,
ncpOutgoingVTLCallFailures Counter32,
ncpMemoryFree DisplayString,
ncpDosPartitionFree DisplayString,
ncpHtfsPartitionFree DisplayString,
ncpPowerStatus INTEGER,
ncpNumberOfVMPorts Integer32
}
480
APPENDIX F: NBX ENTERPRISE MIB
ncpNumberOfActiveCallsOBJECT-TYPE
SYNTAXInteger32
MAX-ACCESSread-only
STATUScurrent
DESCRIPTION"Indicates a number to track the number of active calls."
::= { ncpEntry 1 }
ncpIncomingVTLCallFailuresOBJECT-TYPE
SYNTAX Counter32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Indicates a Counter to track the number of
Failures"
::= { ncpEntry 2 }
Incoming VTL Call
ncpOutgoingVTLCallFailuresOBJECT-TYPE
SYNTAX Counter32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Indicates a Counter to track the number of Outgoing VTL Call
Failures"
::= { ncpEntry 3 }
-- Though the Memory free is in MB, to present the accurate value, it is better
-- to use the display string.
ncpMemoryFreeOBJECT-TYPE
SYNTAXDisplayString
MAX-ACCESSread-only
STATUScurrent
DESCRIPTION"Indicates the free Memory in the system"
::= { ncpEntry 4 }
-- This is a display string as the number is greater than the maximum value
-- that an integer can store. The value is in GB. So better to display in
-- display string.
ncpDosPartitionFreeOBJECT-TYPE
SYNTAXDisplayString
MAX-ACCESSread-only
STATUScurrent
DESCRIPTION"Indicates the Dos partition that is free"
::= { ncpEntry 5 }
-- This is a display string as the number is greater than the maximum value
-- that an integer can store. The value is in GB. So better to display in
481
-- display string.
ncpHtfsPartitionFreeOBJECT-TYPE
SYNTAXDisplayString
MAX-ACCESSread-only
STATUScurrent
DESCRIPTION"Indicates the HTFS partition that is free"
::= { ncpEntry 6 }
-- The status of the power supply present in the NCP. In some of the NBX systems
there will
-- be two power supplies. This object indicates the status of each of the power
supply.
ncpPowerStatusOBJECT-TYPE
SYNTAX INTEGER {
ps1Failed ( 1 ) ,
ps2Failed ( 2) ,
allOk ( 3 )
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Indicates the power status of the NCP when redundant
power supply is available."
::= { ncpEntry 7 }
ncpNumberOfVMPorts OBJECT-TYPE
SYNTAXInteger32
MAX-ACCESSread-only
STATUScurrent
DESCRIPTION"Indicates the number of voicemail ports that are present in the
NBX"
::= { ncpEntry 8 }
-- The Operations table starts from here. This is used for doing a NCP reboot
shutdown.
ncpOperationTableOBJECT-TYPE
SYNTAXSEQUENCE OF NcpOperationEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"This table consists of objects meant for rebooting and
shutting down the NBX system."
::= { nbxCallProcessor 3 }
or
482
APPENDIX F: NBX ENTERPRISE MIB
ncpOperationEntryOBJECT-TYPE
SYNTAXNcpOperationEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an Entry for the operations table."
INDEX { entPhysicalIndex }
::={ ncpOperationTable 1}
NcpOperationEntry ::= SEQUENCE {
ncpOperationReboot INTEGER,
ncpOperationShutDown INTEGER
}
-- For this version, we are not supporting the scheduled reboot and shut
-- down features
ncpOperationRebootOBJECT-TYPE
SYNTAX INTEGER {
inActive(1),
active(2)
}
MAX-ACCESSread-write
STATUScurrent
DESCRIPTION"This object is used to set the NCP to reboot. When set to
active(2) the NBX is rebooted. When a GET is done, then
the inActive(1) is returned indicating the current
status."
::= { ncpOperationEntry 1 }
ncpOperationShutDownOBJECT-TYPE
SYNTAX INTEGER {
inActive(1),
active(2)
}
MAX-ACCESSread-write
STATUS current
DESCRIPTION"This object is used to set the NCP to Shut Down. When set
to active(2) the NCP is Shut down. When a GET
is done then the inActive(1) is returned."
::= { ncpOperationEntry 2 }
-- The licenses table starts from here.
ncpLicenseTableOBJECT-TYPE
SYNTAXSEQUENCE OF NcpLicenseEntry
MAX-ACCESSnot-accessible
STATUScurrent
483
DESCRIPTION" The table consists of the licenses that are in use and the purpose
used
::=
for in the NBX system"
{ nbxCallProcessor 4 }
ncpLicenseEntryOBJECT-TYPE
SYNTAXNcpLicenseEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an Entry for the Licenses table."
INDEX { ncpLicenseIndex }
::= { ncpLicenseTable 1 }
NcpLicenseEntry ::= SEQUENCE {
ncpLicenseIndex Integer32,
ncpLicenseName INTEGER,
ncpLicenseDescription DisplayString,
ncpLicenseTotal Integer32,
ncpLicenseInUse Integer32
}
ncpLicenseIndexOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The License Index is a unique number to distinguish
the licenses that are present in the NBX system"
::= { ncpLicenseEntry 1 }
-- The License name is indicative of the feature for which respective access is
enabled.
-- these are taken from License.cpp file.
-- Because of some limitations the voicemail feature codes are abbrievated. for
example, the code
-- vmNbx100Upg4H4PFrom30M4P should be read as voice mail upgraded to 4 Hrs 4 Ports
From 30min 4Ports.
-- vmNbx100Upg20H6PFrom30M4P should be read as voice mail upgraded to 20 Hours 6
Ports from 30 min 4 ports .
-- vm denotes voicemail,P for ports,H for Hours, M for Min.
ncpLicenseNameOBJECT-TYPE
SYNTAX INTEGER {
deviceCount(1),
diskMirroring(2),
voiceMail(3),
vmPortCount(4),
vmNbx100Upg4H4PFrom30M4P(5),
484
APPENDIX F: NBX ENTERPRISE MIB
vmNbx100Upg20H6PFrom30M4P(6),
vmNbx100UpgMaxH12PFrom30M4P(7),
vmNbx100Upg20H6PFrom4H4P(8),
vmNbx100UpgMaxH12PFrom4H4P(9),
vmNbx100UpgMaxH12PFrom20H6P(10),
ip(11),
ipStandard(12),
ipOnTheFly(13),
ipUpgrade(14),
h323NTCount(15),
softphoneCount(16),
wavDeviceCount(17),
vtlPortCount(18),
vpim(19),
thirdPartyMsg(20),
cas(21),
callRecordMonitor(22),
tpPolycomCount(23),
tpCitelNorstar(24),
vmNbx100DefaultLicense(26),
starFish(28),
softwareUpgrade(29),
citelAvaya2GatewayLicense(30),
tpCitelAnalog(31),
citelOther2Gateway(32),
citelOther3Gateway(33),
desoto(34),
basicPhone3101(36),
group2(37),
group1(38),
group0(40),
group3(43),
group4(44),
nbxACD(45),
bri2portto4port(46),
v3001RDiskMirroringKit(47),
invalidLicense(48),
unknownLicense(49)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The license Name for which the access is allowed. It is an
enumerated type
which represents the corresponding License."
::= { ncpLicenseEntry 2 }
485
ncpLicenseDescriptionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The description of the License."
::= { ncpLicenseEntry 3 }
ncpLicenseTotalOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Total Number of devices available to be used in the system
using the particular
license."
::= { ncpLicenseEntry 4 }
ncpLicenseInUseOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The total number of units that are being used in system."
::= { ncpLicenseEntry 5 }
-- The Gateways Group, This group is one of the groups configured under nbx object
identifier.
-- Implementation of this group is mandatory for all systems
-- This group contains a Table of all the gateways that form part of an nbx system.
-- The NCP discovers and proxies the configuration specific to digital
-- or analog gateways.
gatewayTableOBJECT-TYPE
SYNTAXSEQUENCE OF GatewayEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"The table consists of the list of gateway devices that are
connected to the NBX. This list
includes the List of TLIM,PRI, BRI, ATC etc. The device class will
differentiate the type of device
attached to the NBX."
::= { nbxGateway 1 }
486
APPENDIX F: NBX ENTERPRISE MIB
gatewayEntryOBJECT-TYPE
SYNTAXGatewayEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an Entry for each gateway in the Gateway table."
INDEX { gatewayDeviceId }
::= { gatewayTable 1 }
GatewayEntry ::= SEQUENCE {
gatewayDeviceId
Integer32,
gatewayMacAddress PhysAddress,
gatewayClass INTEGER,
gatewaySerialNumber DisplayString,
gatewayPartNumber DisplayString,
gatewayHWVersion DisplayString,
gatewaySWVersion DisplayString,
gatewayIPAddress IpAddress,
gatewayIPMask IpAddress,
gatewayIPGateway IpAddress,
gatewayDescription DisplayString,
gatewayDeviceName DisplayString,
gatewayStatus INTEGER,
gatewayNumberOfChannels Integer32,
gatewayModelNumber DisplayString,
gatewayReboot INTEGER
}
-- The gateway class is meant to indicate the type of gateway present in the system.
-- The enum other indicates any other gateway that is present in the system other
than
-- the T1,ISDN PRI,BRI cards that are generally supported.
gatewayDeviceIdOBJECT-TYPE
SYNTAX Integer32 ( -2147483648 .. 2147483647 )
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The Device ID of the Gateway connected to the NBX."
::= { gatewayEntry 1 }
gatewayMacAddressOBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The MAC address of the Gateway connected to the NBX."
::= { gatewayEntry 2 }
487
-- The enums that are given here are as mentioned in the dbconst.h. Changing the
order will
-- effect the complexity of code for handling the enums.
gatewayClassOBJECT-TYPE
SYNTAX INTEGER {
tlimGrowler(4),
tlimProto(5),
tlimAlpha(6),
tlimH323(13),
ata(15),
t1(16),
t1Channel(17),
isdnBRI(18),
chasis(31),
trunkGroup(36),
trunkSpan(37),
trunkPriSpan(40),
trunkBriSpan(41),
trunkPriChannel(42),
trunkBriChannel(43),
trunkPriGroup(44),
trunkBriGroup(45),
trunkDSP(46),
ataMorticia(58),
tlimGomez(59),
trunkPriDChannel(61),
trunkBriDChannel(62),
ataThirdPart(63),
ataWednesday(64),
trunkSpanLoopback(65),
trunkPriSpanLoopback(66),
ataSkylark(94),
unknownGatewayClass(100),
isdnPRI(101)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"An enumeration for E1,T1,PRI,BRI,ATA etc."
::= { gatewayEntry 3 }
gatewaySerialNumberOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
488
APPENDIX F: NBX ENTERPRISE MIB
DESCRIPTION"The 3Com 13 digit Serial Number present on the gateway."
::= { gatewayEntry 4 }
gatewayPartNumberOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The 3C Part Number of the Gateway."
::= { gatewayEntry 5 }
gatewayHWVersionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The hardware verison of the gateway."
::= { gatewayEntry 6 }
gatewaySWVersionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Software Version of the gateway."
::= { gatewayEntry 7 }
gatewayIPAddressOBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP Address of the Gateway."
::= { gatewayEntry 8 }
gatewayIPMaskOBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP mask of the respective Gateway connected to the NBX."
::= { gatewayEntry 9 }
gatewayIPGatewayOBJECT-TYPE
SYNTAX IpAddress
489
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP Gateway address of the gateway."
::= { gatewayEntry 10 }
gatewayDescriptionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Description about the Gateway that is connected to the NBX."
::= { gatewayEntry 11 }
gatewayDeviceNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The name of the gateway ."
::= { gatewayEntry 12 }
-- The enums that are given here are as mentioned in the dbconst.h. Changing the
order will
-- effect the complexity of code for handling the enums.
gatewayStatusOBJECT-TYPE
SYNTAX INTEGER {
online(1),
offline(3),
unknownGatewayStatus(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"An enumeration that gives the status of the gateway, as
online,offline,unknown,etc."
::= { gatewayEntry 13 }
gatewayNumberOfChannelsOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Number of channels or ports that are onboard for the
corresponding Gateway."
::= { gatewayEntry 14 }
490
APPENDIX F: NBX ENTERPRISE MIB
gatewayModelNumberOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The model number of the gateway."
::= { gatewayEntry 15 }
-- The gateway reboot will allow the users to set the respective gateway to
reboot.
gatewayRebootOBJECT-TYPE
SYNTAX INTEGER {
inActive(1),
active(2)
}
MAX-ACCESSread-write
STATUS current
DESCRIPTION"The object will allow users to reboot the specific gateway. Setting
the object
with active(2) will reboot the respective gateway."
::= { gatewayEntry 16 }
-- nbxDlC is in the gateway group. It gives the span and channel information of
digital line cards that
-- are connected to the nbx.
gatewayDLCOBJECT IDENTIFIER
::= { nbxGateway 2 }
dlcSpanTableOBJECT-TYPE
SYNTAXSEQUENCE OF DlcSpanEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"This table gives the information of the span entries of various
Digital line cards that are connected to the nbx."
::= { gatewayDLC 1 }
dlcSpanEntryOBJECT-TYPE
SYNTAXDlcSpanEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an entry for each of the Span in the DLC"
INDEX { dlcSpanDeviceId }
::= { dlcSpanTable 1 }
DlcSpanEntry ::= SEQUENCE {
dlcSpanDeviceId Integer32,
dlcSpanMACAddress PhysAddress,
491
dlcSpanID Integer32,
dlcSpanName DisplayString,
dlcSpanSignalProtocol INTEGER,
dlcSpanFraming INTEGER,
dlcSpanLineCode INTEGER,
dlcSpanLineLength INTEGER,
dlcSpanTimingMode INTEGER,
dlcSpanNumberOfChannels Integer32,
dlcSpanNumberOfChannelsOnline Integer32,
dlcSpanNumberOfChannelsOffline Integer32,
dlcSpanStatus INTEGER,
dlcSpanTEIManualAuto INTEGER,
dlcSpanTEIId DisplayString
}
dlcSpanDeviceIdOBJECT-TYPE
SYNTAX Integer32 ( -2147483648 .. 2147483647 )
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The span device ID is a unique number
that identifies the respective span."
::= { dlcSpanEntry 1 }
dlcSpanMACAddressOBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The MAC address of the Span."
::= { dlcSpanEntry 2 }
dlcSpanIDOBJECT-TYPE
SYNTAX Integer32 ( -2147483648 .. 2147483647 )
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The span device ID is a unique Virtual device number
that identifies the respective span."
::= { dlcSpanEntry 3 }
dlcSpanNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The name of the span configured in the
NBX."
::= { dlcSpanEntry 4 }
492
APPENDIX F: NBX ENTERPRISE MIB
-- The enums that are given here are as mentioned
order will
-- effect the complexity of code for handling the
dlcSpanSignalProtocolOBJECT-TYPE
SYNTAX INTEGER {
ess5(1),
dms(2),
ni2(3),
qSigSlave(4),
qSigMaster(5),
t1QSigSlave(6),
t1QsigMaster(7),
ess4(8),
etsi(9) ,
protocolNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Describes the Protocol used
by the span."
::= { dlcSpanEntry 5 }
-- The enums that are given here are as mentioned
order will
-- effect the complexity of code for handling the
in the gNipTep.h. Changing the
enums.
in the gNipTep.h. Changing the
enums.
dlcSpanFramingOBJECT-TYPE
SYNTAX INTEGER {
crcmf(1),
f4mf(2),
f12mf(3),
esf(4),
f72mf(5),
d4(6),
df(7),
framingNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Enumeration describing the Framing type
used by the card."
::= { dlcSpanEntry 6 }
-- The enums that are given here are as mentioned in the gNipTep.h. Changing the
order will
-- effect the complexity of code for handling the enums.
dlcSpanLineCodeOBJECT-TYPE
493
SYNTAX
INTEGER {
hdb3(1),
b8zs(2),
ami(3) ,
lineCodeNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The line code used by the span."
::= { dlcSpanEntry 7 }
dlcSpanLineLengthOBJECT-TYPE
SYNTAX INTEGER
{
t1_len_000035(1),
t1_len_025056(2),
t1_len_055095(3),
t1_len_085125(4),
t1_len_115155 (5),
t1_len_145185 (6),
t1_len_175210(7),
t1_len_dbLongHaul(8),
t1_len_7dbLongHaul(9),
t1_len_15dbLongHaul(10),
t1_len_22dbLongHaul(11),
pri_len_000035(51),
pri_len_025056(52),
pri_len_055095(53),
pri_len_085125(54),
pri_len_115155 (55),
pri_len_145185 (56),
pri_len_175210(57),
pri_len_NA(58),
pri_len_dbLongHaul(59),
pri_len_7dbLongHaul(60),
pri_len_15dbLongHaul(61),
pri_len_22dbLongHaul(62),
lineLengthNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The span line length used by the card."
::= { dlcSpanEntry 8 }
494
APPENDIX F: NBX ENTERPRISE MIB
dlcSpanTimingModeOBJECT-TYPE
SYNTAX INTEGER {
internal(1) ,
loop(2),
timingModeNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The timing mode configured for the
Span."
::= { dlcSpanEntry 9 }
dlcSpanNumberOfChannelsOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The number of channels that are present
in the card,"
::= { dlcSpanEntry 10 }
dlcSpanNumberOfChannelsOnlineOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The number of channels that are online
in the span list of the card,"
::= { dlcSpanEntry 11 }
dlcSpanNumberOfChannelsOfflineOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The number of channels that are offline
in the card."
::= { dlcSpanEntry 12 }
dlcSpanStatusOBJECT-TYPE
SYNTAX INTEGER {
online(1),
offline(3),
495
unknownSpanStatus(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The status of the span, whether
online, offline, unknown, etc."
::= { dlcSpanEntry 13 }
-- This object exists only for BRI Span. For the other spans i could not find a
-- mention of that.
dlcSpanTEIManualAuto OBJECT-TYPE
SYNTAX INTEGER {
manual(1),
auto(2) ,
notApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The status of the TEI Assignment. If it is
configured to automatic then auto(2) is returned else
manual(1) is returned. If it doesnot exist notApplicable is returned."
::={ dlcSpanEntry
14}
dlcSpanTEIIdOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION" The TEI ID of the span if exists."
::={ dlcSpanEntry
15}
dlcChannelTableOBJECT-TYPE
SYNTAXSEQUENCE OF DlcChannelEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"This table consists of the details regarding the channels
in the NBX. These include the T1,E1,PRI,BRI etc."
::= { gatewayDLC 2 }
dlcChannelEntryOBJECT-TYPE
SYNTAXDlcChannelEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an entry for each of the Channel in the DLC"
INDEX { dlcChannelDeviceId }
::= { dlcChannelTable 1 }
496
APPENDIX F: NBX ENTERPRISE MIB
DlcChannelEntry ::= SEQUENCE {
dlcChannelDeviceId Integer32,
dlcChannelMAC PhysAddress,
dlcChannelID Integer32,
dlcChannelGroupName DisplayString,
dlcChannelName DisplayString,
dlcChannelSpanId Integer32,
dlcChannelExtension Integer32,
dlcChannelProtocolINTEGER,
dlcChannelDirection INTEGER,
dlcChannelstartType INTEGER,
dlcChannelIncomingDigitFormat INTEGER,
dlcChannelCalledPartyDigits Integer32,
dlcChannelOutgoingDigitFormat INTEGER,
dlcChannelAutoExt Integer32,
dlcChannelStatus INTEGER,
dlcChannelRestart INTEGER,
dlcChannelErrorCountCounter32,
dlcChannelLastErrorCode DisplayString
}
dlcChannelDeviceIdOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The Channel device Id gives the unique number
that identifies the channel
appropriately."
::= { dlcChannelEntry 1 }
dlcChannelMACOBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The MAC address of the channel."
::= { dlcChannelEntry 2 }
dlcChannelIDOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Channel ID gives the unique virtual device number
that identifies the channel
appropriately."
::= { dlcChannelEntry 3 }
497
dlcChannelGroupNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The group name of the channel"
::= { dlcChannelEntry 4 }
dlcChannelNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Name of the DLC channel ."
::= { dlcChannelEntry 5 }
dlcChannelSpanIdOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Span Id of the
::= { dlcChannelEntry 6 }
channel."
dlcChannelExtensionOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Extension of the channel."
::= { dlcChannelEntry 7 }
dlcChannelProtocolOBJECT-TYPE
SYNTAX INTEGER {
did(1),
fxo(2),
fxs(3),
gnd(4),
sigModeClearChannel(5),
em(6),
channelProtocolNotApplicable(100)
}
MAX-ACCESS
read-only
STATUS current
DESCRIPTION"The Protocol used by the channel."
::= {
dlcChannelEntry 8}
498
APPENDIX F: NBX ENTERPRISE MIB
dlcChannelDirectionOBJECT-TYPE
SYNTAX INTEGER {
inOnly(1),
twoWay(2),
channelDirectionNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The direction of the channel, Indicates
if it is one way or two way."
::= { dlcChannelEntry 9 }
dlcChannelstartTypeOBJECT-TYPE
SYNTAX INTEGER {
immediate(1),
delay(2),
dialTone(3),
wink(4),
channelStartTypeNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Indicates the start type of the
channel."
::= { dlcChannelEntry 10 }
dlcChannelIncomingDigitFormatOBJECT-TYPE
SYNTAX INTEGER {
pulse(1),
dnis(2),
dnisAni(3),
sDnis(4),
sDnisAnis(5),
sAnisDnis(6),
dtmf(7),
incomingDigitFormatNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Indicates the incoming digit format of
the channel, whether DNIS, ANI etc."
::= { dlcChannelEntry 11 }
499
dlcChannelCalledPartyDigitsOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Gives the called party digits."
::= { dlcChannelEntry 12 }
dlcChannelOutgoingDigitFormatOBJECT-TYPE
SYNTAX INTEGER {
pulse(1),
dnis(2),
dnisAni(3),
sDnis(4),
sDnisAnis(5),
sAnisDnis(6),
dtmf(7),
outgoingDigitFormatNotApplicable(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Gives the outgoing digit format configured for the channel."
::= { dlcChannelEntry 13 }
dlcChannelAutoExtOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The auto extension configured for the channel."
::= { dlcChannelEntry 14 }
dlcChannelStatusOBJECT-TYPE
SYNTAX INTEGER {
online(1),
offline(3),
unknownChannelStatus(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The status of the respective Channel. Gives whether it is online or
offline
etc."
::= { dlcChannelEntry 15 }
500
APPENDIX F: NBX ENTERPRISE MIB
dlcChannelRestart
OBJECT-TYPE
SYNTAX INTEGER {
inActive(1),
active(2)
}
MAX-ACCESSread-write
STATUS current
DESCRIPTION
"when set to active(2), the channel is restarted"
::= { dlcChannelEntry 16 }
dlcChannelErrorCountOBJECT-TYPE
SYNTAX Counter32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The counter to track the number of times errors
occured in the channel"
::={ dlcChannelEntry 17 }
dlcChannelLastErrorCode OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Last error code returned by the channel"
::= { dlcChannelEntry 18 }
-- The analog line entries are described here. These entries give the analog
-- line details for ALC,ATA etc.
gatewayAnalogLineOBJECT IDENTIFIER
::= { nbxGateway 3 }
analogLineTableOBJECT-TYPE
SYNTAXSEQUENCE OF AnalogLineEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"This table consists of the details
regarding the Analog line card present in the NBX."
::= { gatewayAnalogLine 1 }
-- Here 2 indexes are there one the lineId which indicates the Port number or line
number
-- and the other denotes the mac address of the analog line card.
analogLineEntryOBJECT-TYPE
SYNTAXAnalogLineEntry
MAX-ACCESSnot-accessible
STATUScurrent
501
DESCRIPTION"Indicates an entry for each line or port present in the
Line card"
INDEX { analogDeviceId }
::= { analogLineTable 1 }
AnalogLineEntry ::= SEQUENCE {
analogDeviceIdInteger32,
analogLineMACAddress PhysAddress,
analogLineID Integer32,
analogLineExtension Integer32,
analogLineStatus INTEGER,
analogLineDeviceName DisplayString
}
analogDeviceIdOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The Analog Device ID gives the unique number that identifies
the line appropriately."
::= { analogLineEntry 1 }
analogLineMACAddressOBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Mac address of the ALC card to which the line
belongs to"
::= { analogLineEntry 2 }
analogLineIDOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Analog line ID gives the unique Port number that identifies
the line appropriately."
::= { analogLineEntry 3 }
analogLineExtensionOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Analog Line card Extension gives the extension being used by
the
line or port."
::= { analogLineEntry 4 }
502
APPENDIX F: NBX ENTERPRISE MIB
-- enums taken from gNipTep.h
analogLineStatusOBJECT-TYPE
SYNTAX INTEGER {
online(1),
offline(3),
unknownLineStatus(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The port or line status,i.e information whether the
line is online or offline etc."
::= { analogLineEntry 5 }
analogLineDeviceNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Name of the port or line configured in theNBX."
::= { analogLineEntry 6 }
--The SIP Endpoints table starts from here
gatewaySIPEndPointTableOBJECT-TYPE
SYNTAXSEQUENCE OF GatewaySIPEndPointEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"This table consists of the details
regarding the SIP Endpoints connected to the NBX."
::= { nbxGateway 4 }
-- The device Id of the sip endpoint is the index of the table
gatewaySIPEndPointEntryOBJECT-TYPE
SYNTAXGatewaySIPEndPointEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an entry for each SIP endpoint present Connected to
NBX"
INDEX { gatewaySIPEndPointDeviceId }
::= { gatewaySIPEndPointTable 1 }
GatewaySIPEndPointEntry ::= SEQUENCE {
gatewaySIPEndPointDeviceIdInteger32,
gatewaySIPEndPointIPAddressIpAddress,
gatewaySIPEndPointPortNumberInteger32,
gatewaySIPEndPointDeviceName DisplayString,
503
gatewaySIPEndPointDescription
}
DisplayString
gatewaySIPEndPointDeviceId OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The Device ID of the SIP endpoint."
::= { gatewaySIPEndPointEntry 1 }
gatewaySIPEndPointIPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP address of the SIP endpoint."
::= { gatewaySIPEndPointEntry 2 }
gatewaySIPEndPointPortNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The port number being used by the SIP endpoint."
::= { gatewaySIPEndPointEntry 3 }
gatewaySIPEndPointDeviceNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The name of the SIP endpoint."
::= { gatewaySIPEndPointEntry 4 }
gatewaySIPEndPointDescriptionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The description of the SIP endpoint."
::= { gatewaySIPEndPointEntry 5 }
-- The phone Table group starts from here.
phoneTableOBJECT-TYPE
SYNTAXSEQUENCE OF PhoneEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"The table consists of the list of phones
504
APPENDIX F: NBX ENTERPRISE MIB
::=
that are
includes
the type
{ nbxPhone
connected to the NBX. This list
the List of phones etc. The device class will differentiate
of device attached to the NBX."
1 }
-- The mac address may become a problem for SIP phones, but we have no other
-- alternative other than device id, which, is not that meaningful.
phoneEntryOBJECT-TYPE
SYNTAXPhoneEntry
MAX-ACCESSnot-accessible
STATUScurrent
DESCRIPTION"Indicates an entry for each phone present in the NBX"
INDEX { phoneDeviceId }
::= {phoneTable 1 }
PhoneEntry ::= SEQUENCE {
phoneDeviceIdInteger32,
phoneMACAddress PhysAddress,
phoneVDN Integer32,
phoneClass INTEGER,
phoneExtension DisplayString,
phoneSerialNumber DisplayString,
phonePartNumber DisplayString,
phoneHWVersion DisplayString,
phoneSWVersion DisplayString,
phoneIPAddress IpAddress,
phoneIPMask IpAddress,
phoneIPGateway IpAddress,
phoneDescription DisplayString,
phoneDeviceName DisplayString,
phoneStatus INTEGER
}
phoneDeviceIdOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSnot-accessible
STATUS current
DESCRIPTION"The Device ID of the Phone or ATA device."
::= { phoneEntry 1 }
phoneMACAddressOBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The MAC Address of the Phone device."
::= { phoneEntry 2 }
505
phoneVDNOBJECT-TYPE
SYNTAX Integer32
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The vdn of the ATA device.For phones it will be zero.For SIP
Devices
it indicates the port number being used."
::= { phoneEntry 3 }
-- The phone class is an enumeration which denotes the phone class to which it
belongs to.
-- These enums are given as mentioned in the dbconst.h. Changing the order will
-- effect the complexity of code for handling the enums. So we prefer it being this
way.
phoneClassOBJECT-TYPE
SYNTAX INTEGER {
nbSetGrowler(1),
nbSetProto(2),
nbSetAlpha(3),
nbSetBusiness(4),
nbSetSoft(15),
ata(16),
nbSetWav(48),
basicSet(49),
thirdParty1(51),
thirdParty2(52),
thirdParty3(53),
thirdParty4(54),
thirdParty5(55),
thirdParty6(56),
thirdParty7(57),
thirdParty8(58),
ataMorticia(59),
ataThirdParty1(64),
ataWednesday(65),
nbSet3102Business(66),
cordlessPhone(67),
basicSet3101(70),
singleLineSet3100(75),
managerPhone3103(77),
softPhone3102(80),
wirelessPhone3108(81),
convergenceClient(83),
thirdPartySIPPhone(85),
basicSet3101B(92),
506
APPENDIX F: NBX ENTERPRISE MIB
basicSet3102B(93),
ataSkylark(95),
managerPhone3103B(96),
singleLineSet3100B(97),
unknownPhoneClass(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"An enumeration for describing the class of phone as basic,
bussines, desoto phone etc"
::= { phoneEntry 4 }
phoneExtensionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Extension number of the phone."
::= { phoneEntry 5 }
phoneSerialNumberOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The 3COM 13 digit S/N"
::= { phoneEntry 6 }
phonePartNumberOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The 3C Part Number of the device."
::= { phoneEntry 7 }
phoneHWVersionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The Hardware version of the Phone."
::= { phoneEntry 8 }
phoneSWVersionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
507
STATUS current
DESCRIPTION"The software version of the Phone."
::= { phoneEntry 9 }
phoneIPAddressOBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP address of the Phone."
::= { phoneEntry 10 }
phoneIPMaskOBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP mask of the Phone
::= { phoneEntry 11 }
Device."
phoneIPGatewayOBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The IP gateway address of the phone device,"
::= { phoneEntry 12 }
phoneDescriptionOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"Description for the phone "
::= { phoneEntry 13 }
phoneDeviceNameOBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESSread-only
STATUS current
DESCRIPTION"The name configured for the Phone device."
::= { phoneEntry 14 }
phoneStatusOBJECT-TYPE
508
APPENDIX F: NBX ENTERPRISE MIB
SYNTAX
INTEGER {
online(1),
offline(3),
unknownPhoneStatus(100)
}
MAX-ACCESSread-only
STATUS current
DESCRIPTION"An enumeration for giving information on status of the phone."
::= { phoneEntry 15 }
-- The Notifications Group Begins here.
-- The power status object is associated to the ncpPowerStatus object from the NCP
table
-- along with the physical name of the entity. Most of the NCP related notifications
are associated to
-- the entPhysicalName so as to inform the manager of the NCP that is sending the
notification
-- incase there are 2 NCP's available. By default the index of the table will be
-- mentioned in the notification if it is associated with the table object.
notifyPowerStatusChangeNOTIFICATION-TYPE
OBJECTS { entPhysicalName,ncpPowerStatus }
STATUS current
DESCRIPTION"Notifies if the one of the redundant power supplies status changes
from on to off and vice versa."
::= { nbxNotifications 1 }
-- The IP address is accessed from the MIB 2 IP address table. Therefore the
Notification
-- will be associated with the object of the MIB 2 for IP address entry of the
system.
notifyNCPIPChangeNOTIFICATION-TYPE
OBJECTS { entPhysicalName,ipAdEntAddr}
STATUS current
DESCRIPTION"Notifies if there is a change in the IP
address of the NCP."
::= { nbxNotifications 2 }
-- This notifications is fired when the voicemail ports that are available in the
system get
-- exhausted.
notifyVoiceMailPortsExhaustedNOTIFICATION-TYPE
OBJECTS { entPhysicalName,ncpNumberOfVMPorts }
STATUS current
DESCRIPTION"Notifies if the voice mail
ports get exhausted."
509
::=
{
nbxNotifications
3
}
-- This notification is fired whenever an administrator fails to logon properly.
-- The object to which this is mapped is the entPhysicalName of the Entity table.
notifyFailedLogonAttemptNOTIFICATION-TYPE
OBJECTS { entPhysicalName }
STATUS current
DESCRIPTION"Notifies if there is a Failed logon
attempt by the Administrator."
::= { nbxNotifications 4 }
notifyVTLConnectionFailureNOTIFICATION-TYPE
OBJECTS { entPhysicalName}
STATUS current
DESCRIPTION"Notifies if any of the incoming or
outgoing VTL calls result in a Failure."
::= { nbxNotifications 5 }
-- The phone extension is not a table object and therefore the phone name is listed.
-- for the phones and gateways the Device name is associated to the notification
objects
-- so that the manager can get to know the device that sent the notification.
-- By default the notification contains the information on the MAC address of
-- phone, gateway,span,channel as it is the index of the respective table.
notifyPhoneStatusChangeNOTIFICATION-TYPE
OBJECTS { phoneStatus,phoneDeviceName }
STATUS current
DESCRIPTION"Notifies if the status of phone
changes."
::= { nbxNotifications 6 }
notifyPhoneIPChangeNOTIFICATION-TYPE
OBJECTS { phoneIPAddress,phoneDeviceName }
STATUS current
DESCRIPTION"Notifies if the IP address of a phone
changes."
::= { nbxNotifications 7 }
notifyGatewayStatusChangeNOTIFICATION-TYPE
OBJECTS { gatewayStatus,gatewayDeviceName }
STATUS current
DESCRIPTION"Notifies if there is a change in the
status of the gateway. The gateways include all the boards of
T1,E1 etc connected to the NBX."
::= { nbxNotifications 8 }
510
APPENDIX F: NBX ENTERPRISE MIB
notifyGatewayIPChangeNOTIFICATION-TYPE
OBJECTS { gatewayIPAddress,gatewayDeviceName }
STATUS current
DESCRIPTION"Notifies if there is a change in the IP
Address of the gateway,"
::= { nbxNotifications 9 }
-- The notification gets fired if all the ports get busy in a gateway. The
notification is associated
-- to a mac address so as to inform the user of the device that has fired.
notifyGatewayAllPortsBusyNOTIFICATION-TYPE
OBJECTS { gatewayDeviceName,entPhysicalName }
STATUS current
DESCRIPTION"Notifies if all the ports of the
Gateway connected to NBX gets busy."
::= { nbxNotifications 10 }
-- spanstatus notification is associated to its name, so that the manager can know
-- which span has sent that.
notifySpanStatusChangeNOTIFICATION-TYPE
OBJECTS { dlcSpanStatus,dlcSpanName }
STATUS current
DESCRIPTION"Notifies if there is a change in the
span status of the Digitl line card"
::= { nbxNotifications 11 }
notifyChannelStatusChangeNOTIFICATION-TYPE
OBJECTS { dlcChannelStatus,dlcChannelName}
STATUS current
DESCRIPTION"Notifies if there is a change in the
channel status of the digital line card."
::= { nbxNotifications 12 }
-- Notifies if there is a change in the link status of the gateway. The
-- device name is associated to indicate the manager as to which gateway and which
-- link has sent the notification.
notifyGatewayLinkStateChangeNOTIFICATION-TYPE
OBJECTS { analogLineStatus,analogLineDeviceName }
STATUS current
DESCRIPTION"Notifies if there is a change in the
status of the line card ports that are
connected to the NBX."
::= { nbxNotifications 13 }
-- Notifies if any of the license limits are exceeded in a NBX.
511
nbxLicenseLimitThresholdNOTIFICATION-TYPE
OBJECTS { entPhysicalName,ncpLicenseName }
STATUS current
DESCRIPTION"Notifies if the threshold for the License is exceeded."
::= { nbxNotifications 14 }
nbxLicenseAddDeleteNOTIFICATION-TYPE
OBJECTS {entPhysicalName, ncpLicenseName }
STATUS current
DESCRIPTION"Notifies if a new license is added or deleted"
::= { nbxNotifications 15 }
END
512
APPENDIX F: NBX ENTERPRISE MIB
GLOSSARY
ABCDEFGHIJK
LMNOPQRSTU
VWXYZ
Symbols
10BASE-T
A form of Ethernet and IEEE 802.3 network cabling using twisted pair. It
provides 10Mbits/s with a maximum segment length of 100 m (382 ft).
10BASE2
An implementation of IEEE 802.3 Ethernet standard, often called thinnet
or cheapernet, because it uses thin coaxial cable. 10BASE2 runs at a data
transfer rate of 10 Mbits/s with a maximum segment length of 185 m
(607 ft) per segment.
911
The emergency service that provides a single point of contact for police
and fire departments. See also E911.
account codes
ADSL
Codes that allow you to keep track of calls associated with a client or
account for tracking purposes.
Asymmetrical Digital Subscriber Line. A telephone line that delivers
high-speed data services, such as Internet access, videoconferencing,
interactive TV, and video on demand. The line is split asymmetrically so
that more bandwidth can be used from the telephone company to the
customer (downstream) than from the customer to the telephone
company (upstream).
ATM
Asynchronous Transfer Mode. A cell-based data transfer technique in
which channel demand defines packet allocation. ATM offers fast packet
technology, real-time, demand-led switching for efficient use of network
resources.
Attendant Console
A standard telephony device that shows the status of each extension in a
telephone system. The Attendant Console is usually used by a
514
GLOSSARY
receptionist to connect incoming calls to the correct extension. All
incoming calls ring at the telephone associated with the Attendant
Console.
AUI
auto dial
Attachment Unit Interface. The IEEE 802.3-specified cable and connector
used to attach single-channel and multiple-channel equipment to an
Ethernet transceiver. Defined in Section 7 of the 802.3 standard.
A feature that opens a line and dials a preprogrammed telephone
number.
Auto Attendant
A system feature that provides incoming callers with menu options to
help them reach the appropriate person or information.
Auto Discovery
A feature that “discovers” a new telephone or other device on the
network. A new telephone receives a default telephone number that
displays on the telephone display panel. A new device is assigned one or
more extension numbers or device numbers.
auto redial
autorelocation
ACD
A modem, fax, or telephone feature that redials a busy number a fixed
number of times before giving up.
A feature that allows a telephone to keep its extension number and
personal and systems settings when you connect it to a different Ethernet
jack on the same LAN.
Automatic Call Distribution. A feature that distributes calls to agents
and queues the calls that have not been answered before a
pre-determined time period expires. The ACD also manages recorded
announcements to callers, manages individual ACD agents and groups
of agents, and provides database reports on both calls and agents.
B
backbone
bandwidth
BRI
A high-capacity network that links together other networks of lower
capacity. A typical example is a Frame Relay or ATM backbone that serves
a number of Ethernet LAN segments.
The capacity of a connection method to carry data.
Basic Rate Interface. An ISDN standard that allows two circuit-switched B
(bearer) channels of 64 Kbps each plus one D (data) channel at 16 Kbps
for a total of 144 Kbps to be carried over a single twisted pair cable.
GLOSSARY
bridge
bridged extension
515
A networking device that connects two separate local area networks and
makes the LANs look like a single LAN, passing data between the
networks and filtering local traffic.
An extension of a primary telephone that displays on one or more
secondary telephones. Incoming calls and indeed any activity associated
with the primary telephone can be managed on any of the secondary
telephones.
broadcast
A simultaneous transmission method that sends each packet from one
node to all other nodes.
buffer
A temporary storage area for data that compensates for a difference in
transmission speeds.
bus topology
byte
call coverage point
A type of network in which all devices are connected to a single cable. All
devices that are attached to a bus network have equal access to it, and
they can all detect all of the messages that are put on to the network.
A unit of 8 bits that forms a unit of data. Usually each byte stores one
character.
The user-specified destination for the call forward feature, that is, how
the system is to manage incoming calls when the user is unable to
answer the telephone.
C
caller ID
A telephone company service that displays the name and number
associated with an incoming call. Also called calling line ID or CLI. See
also CLIR.
call forward
A feature that allows calls to be transferred to a call coverage point (voice
mail, the Auto Attendant, or a prespecified telephone number) when the
user is unable to answer the telephone.
calling groups
A feature that transfers incoming calls to a specified group of telephones.
All telephones ring at the same time. See also hunt groups.
call park
A feature that places a call in a “holding pattern” and makes it available
for others to pick up from any telephone on the system.
call permissions
Restrictions that an administrator establishes to control the types of calls
that users can place from their telephones. Most permissions are based
on the time of day. See also CoS (Class of Service).
516
GLOSSARY
call pickup
A feature that allows users to retrieve calls that ring on other telephones.
Call Processor
The device that manages call traffic, voice mail, the Auto Attendant, and
related applications in an system.
call reports
A feature that downloads data about calls and creates simple reports or
exports the data for use in spreadsheets, word processors, or reporting
programs.
category 3
The cable standard for UTP (unshielded twisted pair) voice-grade cabling
that is specified by EIA/TIA 568 for use at speeds of up to 10Mbit/s,
including 10BASE-T Ethernet.
category 4
The cabling standard specified by EIA/TIA 568 for use at speeds of up to
20Mbit/s.
category 5
The cabling standard specified by ElA/TIA 568 for use at speeds of up
to 100 Mbit/s including FDDI (TP PMD), 100BASE-T and
100BASE-VG-AnyLan, and potentially ATM at 155Mbit/s.
Channel Service Unit
(CSU)
client/server
computing
CLI
CLIR
Equipment installed on customer premises to terminate a DDS or T1
circuit. CSUs provide network protection and diagnostic capabilities and
regenerate the signal received from the network. The CSU also controls
pulse shape and amplitude for the transmission of the signal into the
network.
The division of an application into two parts that are linked by a network.
A typical example is a database application in which the database and
application software reside on a server, and the interface for entering or
retrieving information resides on individual workstations (clients).
See caller ID.
Calling Line Identity Restriction. A telephone company option that allows
the caller to withhold caller identity from the person being called.
coaxial cable
High-capacity networking cable that is formed by an outer braided wire
or metal foil shield surrounding a single inner conductor, with plastic
insulation between the two conducting layers. “Coax” cable is used for
broadband and baseband communications networks. Ethernet employs
thin coaxial cable in 10BASE2 and thick cable in 10BASE5.
CODEC
COmpressor/DECompressor. A hardware circuit or software routine that
compresses and decompresses digitized audio, video, or image data.
GLOSSARY
517
Most codecs include the functions of A/D and D/A conversion as well as
compression and decompression.
COder/DECoder. A hardware circuit that converts analog audio or video
signals into digital code, and vice versa, using techniques such as pulse
code modulation and delta modulation. A CODEC is an A/D and
D/A converter.
collapsed backbone
Network architecture in which the backplane of a device, such as a hub,
performs the function of a network backbone. Example: The backplane
routes traffic between desktop nodes and between other hubs serving
multiple LANs.
collision
The result of two devices on a shared transmission medium, like Ethernet,
transmitting simultaneously. Both devices must retry their transmissions.
A delay mechanism used by both senders drastically reduces the chances
of another collision.
collision detection
Ethernet devices detect collisions instantly and attempt to resend. This is
the principle on which CSMA/CD (Carrier Sense Multiple Access with
Collision Detection) is based and the access control method for Ethernet.
concentrator
A central chassis into which various modules, such as bridging,
supervisory, and 10BASE-T cards are plugged.
congestion
The result of increased network use on a LAN segment. Standard
network partitioning practices must be invoked to reduce bottlenecks
and maximize throughput speeds on the segment.
contention
The method used to resolve which users gain access to crowded
bandwidth.
CO
Central Office. A telephony term for the telephone company site that
houses the PSTN switching equipment.
CoS
Class of Service. A collection of call permissions that are assigned to
individual users and govern the times and types of calls these users can
make.
CPE
Customer Premises Equipment. Telecommunications equipment,
including PBX systems and wiring, that is located in a user’s premises.
518
GLOSSARY
CSU
Channel Service Unit. Data transmission equipment to repeat the signal
from the carrier and link to CPE. Vendors add value to CSUs by adding
performance monitoring and management features.
CTI
Computer Telephony Integration. A generic name for the technology that
connects computers and telephone systems through software
applications.
D
data compression
A method of reducing the amount of data to be transmitted by reducing
the number of bits needed to represent the information.
delayed ringing
Prevents a telephone on a shared line from ringing until the incoming call
has rung on other telephones a set number of times.
delayed ringing
pattern
The definition for the order in which telephones ring and how many
times each telephone rings.
demand priority
access
A method for supporting time-sensitive applications such as video and
multimedia as part of the proposed 100BASE-VG standard offering
l00Mbit/s over voice-grade UTP cable.
DHCP
Dynamic Host Configuration Protocol. A method by which devices are
assigned temporary, renewable IP addresses by a server when the devices
become active on the network.
DID/DDI
Direct Inward Dial/Direct Dialing Inward. A feature that allows outside
calls to reach an internal extension without going to an operator or
Automated Attendant.
direct mail transfer
Transfers a caller directly to another user’s voice mail without requiring
them to wait through ringing and without interrupting the recipient.
domain
DSP
DSU/CSU
A group of nodes on a network that form an administrative entity. A
domain can also be a number of servers that are grouped and named to
simplify network administration and security.
Digital Signal Processor. A special-purpose CPU tailored to manage
complex mathematical functions. A DSP takes an analog signal and
reduces it to numbers so its components can be isolated, sampled, and
rearranged more easily than in analog form.
Digital (or Data) Service Unit/Channel Service Unit. A pair of
communications devices that connect an in-house line to an external
GLOSSARY
519
digital circuit (such as T1 and DDS). It is similar to a modem, but connects
a digital circuit rather than an analog circuit.
DTMF
Dual Tone Multi-Frequency. A term for push button dialing. The pushed
button generates a pair of tones which uniquely identify the button that
was pressed.
E911
Enhanced 911. The addition of two features to the standard 911 service:
one is ANI (Automatic Number Identification) to identify the person
associated with the calling telephone, and the other is ALI (Automatic
Location Identification) to identify the physical location of the calling
telephone.
E
encapsulation
The process of sending data encoded in one protocol format across a
network operating a different protocol, where it is not possible or
desirable to convert between the two protocols. Also known as protocol
tunneling.
error correction
A technique to restore data integrity in received data that has been
corrupted during transmission. Error correction techniques involve
sending extra data. The correct form of the data can be reconstructed
from the extra information.
error detection
A set of techniques that can be used to detect errors in received data.
Parity checking techniques include the use of parity bits, checksums or a
Cyclic Redundancy Check (CRC).
Ethernet
The most widely used LAN transmission protocol. Based on a network bus
topology, it runs at a maximum 10Mbit/s and can use a wide variety of
cable types. The IEEE Ethernet standard is IEEE 802.3.
Ethernet switching
A technique that brings the advantages of a parallel networking
architecture to contention-based Ethernet LANs. Each LAN can be
segmented with its own path. When users on different segments
exchange data, an Ethernet switch dynamically connects the two
separate Ethernet channels without interfering with other network
segments.
F
fast Ethernet
An evolution of Ethernet that raises the bandwidth to 100 Mbit/s.
520
GLOSSARY
fast packet switching
A WAN technology for transmitting data, digitized voice, and digitized
image information. It uses short, fixed length packets.
FDDI
Fiber Distributed Data Interface. An optical fiber-based token-passing ring
LAN technology that carries data at a rate of 100 Mbit/s.
FRAD
Frame Relay Access Device. A wide-area networking device that forwards
traffic to and from the endpoint of a the network.
frame
A structured group of bits sent over a link. A frame can contain control,
addressing, error detection, and error correction information. The term is
often used synonymously with the term packet.
frame relay
A packet-switching wide-area technology for interconnecting LANs at
high speeds.
G
gateway
gigabit Ethernet
glare
group mailboxes
A network device that provides a means for network traffic to pass from
one topology, protocol, or architecture into a different topology, protocol,
or architecture.
An Ethernet technology that raises transmission speed to 1 Gbit/s,
targeted primarily for use in backbones.
A condition in telephony where both ends of an available connection are
seized at the same time.
Mailboxes that are not associated with a single telephone but allow a
group of users to have joint access to a single mailbox.
H
H.323
header
hierarchical network
An ITU standard for the transmission of real-time audio, video, and data
communications over packet-switched networks, such as local area
networks (LANs) and the Internet. H.323 is the basis for Internet
telephony.
The control information added to the beginning of a transmitted
message. This may consist of packet or block address, destination,
message number and routing instructions.
A network with one host at its hub, which is the major processing center,
and one or more satellite processing units.
GLOSSARY
hot swap
521
The ability of a device to have parts removed and replaced without
turning off the device and without interrupting the service the device
provides.
hub
The center of a star topology network or cabling system. A multi-node
network topology that has a central multiplexer with many nodes feeding
into and through the multiplexer or hub. The nodes do not directly
interconnect.
hunt groups
Informal “call centers” in which a call rings to one member of the group.
If there is not answer, the call rings at the next member’s telephone and
so on until a member answers.
hybrid mode
A PBX operating mode in which some outside lines are grouped together
in pools while other lines are assigned directly to buttons on telephones.
Users access outside lines by dialing a pool access code. See also key
mode.
I
IEEE
Institute of Electrical and Electronic Engineers. A U.S. publishing and
standards organization responsible for many LAN standards, such as the
802 series.
IEEE 802.2
The Data Link standard for use with IEEE 802.3, 802.4 and 802.5
standards. It specifies how a basic data connection must be set up over
the cable.
IEEE 802.3
The Ethernet standard. A physical layer definition that includes
specification for cabling plus the method of transmitting data and
controlling access to the cable.
IETF
IMAP
intelligent hub
Internet Engineering Task Force. The standards-setting body for the
Internet. Protocols adopted by the IETF define the structure and the
operation of the Internet.
Internet Message Access Protocol. A method of accessing electronic
messages that are kept on a server. IMAP defines how an e-mail program
can access messages that are stored on a remote server.
See managed hub.
522
GLOSSARY
IP
Internet Protocol. The TCP/IP standard protocol that defines the IP
datagram as the unit of information passed across an Internet. IP provides
the basis for connectionless packet delivery service.
IP address
The address used by devices on the network to establish their unique
identity. IP addresses are composed of four fields separated by dots. Each
field is an 8-bit number (0 through 255). IP addresses can be permanently
assigned, or they can be temporarily assigned by DHCP.
IP telephony
ISDN
ITU
Technology that allows voice, data, and video to be transmitted over
IP-based networks.
Integrated Services Digital Network. An international telecommunications
standard for transmitting voice, video and data over digital lines running
at 64 Kbps. ISDN uses B channels, or “bearer” channels, to carry voice
and data. It uses a separate D channel, or “delta,” channel for control
signals to the telephone company computer.
International Telecommunication Union. An international standards
organization for telecommunications.
J
jitter
The variation in latency (waiting time) for different packets on the
network. For real time data such as voice transmission, jitter must be kept
to a minimum.
K
key mode
A telephone system operating model in which each telephone in the
system has buttons for each available outside line. Also known as a
square plan or a direct system inward access (DISA) system. See also
hybrid mode.
L
LAN
local area network. A communications system that links computers,
printers, and other devices. LANs allow users to communicate and share
resources like hard disk storage and printers. Devices linked by a LAN may
be on the same floor or within a building or campus.
LAN segment
A section of a local area network that is used by a particular workgroup or
department and separated from the rest of the LAN by a bridge, router or
switch.
GLOSSARY
LAN switch
latency
layering
LCD
523
A network device that connects stations or LAN segments, also known as
a frame switch.
The sum of all the delays in an end-to-end connection.
The process of dividing complex software up into several layers, each of
which performs a specific task. Layering allows faster and easier software
development and is often used in public, open software.
Liquid Crystal Display. A low cost display technology.
line pool
In a PBX system, outside lines are pooled and arbitrated by the Call
Processor. To call an outside number, a user must dial the line pool access
number, typically 9, and the Call Processor assigns the next available line.
LLC
Logical Link Control. A data link protocol for LANs that is part of the IEEE
802.2 standard and common to all LAN standards for OSI model data
link, level two transmissions.
loop start
The most common signaling method in the public telephone network,
typically used for residence and business CO lines.
M
MAC
MAC address
managed hub
Media Access Control. A sub-layer of the Data Link layer (Layer 2) of the
ISO OSI model responsible for media control. Also known as the “MAC
layer.”
A unique 48-bit number that is encoded in the circuitry of a device to
identify it on a LAN. Also known as a “hardware address” or an
“Ethernet address.”
A network device in which each port on the hub can be configured,
monitored, and enabled or disabled by a network administrator from a
hub management console or utility tied into an SNMP (Signaling Network
Management Protocol) platform. Hub management can also include
gathering information about network parameters.
MAU
Medium Attachment Unit. A transceiver that provides the correct
electrical or optical connection between the computer and IEEE 802.3
LAN media.
MIB
Management Information Base. A database that can be accessed by a
gateway running CMIP (Common Management Information Protocol),
524
GLOSSARY
CMOT (CMIP Over TCP/IP), or SNMP (Signaling Network Management
Protocol) network management protocols. The MIB defines variables
needed by the protocol to monitor and control components in a network.
Managers can fetch or store these variables.
modem
multiplexer
MOdulator/DEModulator. A modem converts a binary bit stream to an
analog signal and vice versa.
A device that can send several signals over a single line. A similar device
at the other end of the link then separates the signals.
multi-tasking
The concurrent execution of two or more tasks or the concurrent use of a
single program that can carry out many functions.
MWI
Message Waiting Indicator. A feature that informs the recipient by means
of a lit status light or LCD display panel that the recipient has a pending
message.
N
NetBEUI
NetBios Extended User Interface. A network device driver or transport
protocol that is the transport driver supplied with LAN Manager.
NetBios
Network Basic Input/Output System. Software developed by IBM that
provides the interface between the PC operating system, the I/O bus, and
the network. Since its design, NetBIOS has become a de facto standard.
NetWare
network collisions
network congestion
network layer
LAN Network Operating System and related products developed by
Novell. NetWare is based on the SPX/IPX networking protocols.
Result of two stations simultaneously attempting to use a shared
transmission medium. See collision.
Result of increased network utilization. Creates traffic bottlenecks on
a LAN segment. See congestion.
Layer 3 in the OSI model responsible for the routing and relaying through
one or more networks in multiple link or wide area environments.
network
management
The process and technique of remotely or locally monitoring and
configuring networks.
network ping
A packet transfer that checks logical continuity between a PC and a
specified IP address.
GLOSSARY
NIC
525
Network Interface Card. Controller circuitry that connects a node to a
network, usually in the form of a card in a PC expansion slot. In
conjunction with the NOS (Network Operating System) and PC operating
system, it helps transmit and receive messages on the network.
node
Device on a network that demands or supplies services. Also, a location
where transmission paths are connected.
NOS
Network Operating System. Software that connects all the devices on a
network so that resources can be shared efficiently and managed from a
central location. Novell NetWare is one example of a network operating
system.
O
OEM
off-hook
off-site notification
on-hook
OSI model
Original Equipment Manufacturer. The maker of a product or component
that is marketed by another vendor, integrator, VAR (Value Added
Reseller), or reseller.
The state of a telephone line that allows dialing and transmission but
prohibits incoming calls from being answered. The term stems from the
days when a telephone handset was lifted off of a hook. Contrast with
on-hook.
A feature that sends a message to a pager, outside telephone number, or
e-mail account that informs a user of a voice mail message. The user can
retrieve the messages remotely.
The state of a telephone line that can receive an incoming call.
A conceptual model of hardware and software layers that define when,
how, and in what order data can be transmitted on a network. The OSI
Model defines seven layers:
Layer 7
Application layer
Layer 6
Presentation layer
Layer 5
Session layer
Layer 4
Transport layer
Layer 3
Network layer
Layer 2
Data Link layer
Layer 1
Physical layer
526
GLOSSARY
out-of-band signaling
An extra signal transmitted with the information signal to monitor and
control a transmission. It provides an additional layer of resilience by using
a separate channel.
P
packet
A collection of bits, including address, data, and control information, that
are transmitted together. The terms frame and packet are often used
synonymously.
packet buffer
Memory space reserved for storing a packet awaiting transmission or for
storing a received packet.
packet switching
A method of switching data in a network. Individual packets of a set size
and format are accepted by the network and delivered to their
destination. The sequence of packets is maintained, and destination
established, by the exchange of control information (also contained in the
packets) between the sending terminal and the network before the
transmission starts.
paging
1) A communications service that includes a one-way beeper service,
one-way text service, and two-way text and voice service.
2) A public address announcement system. Many PBX telephone systems
can do paging through the speakers in the telephone sets.
PBX
Private Branch eXchange. An in-house telephone switching system that
interconnects telephone extensions to each other, as well as to the
outside telephone network. It can include functions such as least cost
routing for outside calls, call forwarding, conference calling, and call
accounting.
PCS
Personal Communications Services. Refers to a variety of wireless services
emerging after the U.S. Government auctioned commercial licenses in
late 1994 and early 1995.
phantom mailbox
port
A user profile that uses a telephone number with no associated
telephone. Messages can be sent to the phantom mailbox from within
the voice mail system. The Auto Attendant can route messages to the
phantom mailbox, and you can dial the phantom mailbox directly.
A computer interface capable of attachment to another device, such as a
modem for communicating with a remote terminal or, if the port is within
a hub, to a workstation.
GLOSSARY
POTS
PPP
predictive dialing
pretranslator
preview dialing
PRI
protocol
protocol converter
PSTN
punch-down block
527
Plain Old Telephone Service.
Point-to-Point Protocol. An addition to the Internet protocol suite to help
connect devices where dissimilar transport protocols exist. Typically used
for serial connections to the Internet.
Automated dialing feature in which CTI software predicts when you will
end your current call, and dials the next call in advance.
A device that interprets and modifies a sequence of incoming digits or
transmits outgoing digits.
Automated dialing feature in which CTI software queues the next call to
be made but allows you to check and activate the call.
Primary Rate Interface. An ISDN service for users with large bandwidth
requirements, such as large PBX systems or high performance video
desktop conferencing systems; the ISDN equivalent of a T1 circuit.
A set of rules governing the information flow within a communications
infrastructure. A protocol typically specifies the structure of parameters
like format, timing, and error correction.
A device that translates between two protocols to facilitate
communications between different computers or different systems.
Public-Switched Telephone Network. The term describes the national
telephone network.
Telephony term describing the connector arrangements for distributing
and connecting unshielded and shielded twisted pair wiring inside a
building. Typically found in telephone wiring closets.
Q
Q.921/931
ITU-TS “Q Series” Recommendations describing Lap-D, the Layer 2
protocol for an ISDN D-channel. See OSI model.
R
reconfiguration
The process of physically altering the location or functionality of network
or system elements. Automatic configuration describes the way
sophisticated networks can readjust themselves in the event of a link or
device failing, enabling the network to continue operation.
528
GLOSSARY
redundancy
In data transmission, this refers to characters and bits that can be
removed from a transmission without affecting the message. In data
processing and data communications, it means providing backup for
components so that if one of them fails, the system continues to run
without interruption.
REN
Ringer Equivalency Number. A number that indicates how much power is
required by a telephone to make it ring. When connecting telephones to
a telephone line, the sum of the RENs of the telephones must be less than
the rated REN capacity of the telephone line.
repeater
A device that extends the maximum length of cable that can be used in a
single network.
RMON
Remote Monitoring. A facet of SNMP-based network management, the
RMON MIB (Management Information Base) defines the standard
network monitoring functions for communication between SNMP-based
management consoles and remote monitors. A typical MIB captures
information about a device, but RMON captures information about traffic
between devices.
RJ-11
A four-wire modular connector used by the telephone system.
RJ-45
An eight-wire modular connector used by telephone systems. The
eight-pin modular connectors used for 10BASE-T UTP cable resemble
RJ-45 connectors, but they have substantially different electrical
properties.
router
A network device that links LANs together locally or remotely as part of a
WAN. A network built using routers is often termed an internetwork.
routing
The process of delivering a packet across one or more networks through
the most appropriate path.
SA
System Appearance
S
screen POP
segment
A CTI term for a window that automatically opens on a user’s computer
when a predefined telephone event occurs. For example, an incoming call
could generate a screen pop that lists caller ID information.
A LAN term meaning an electrically continuous piece of the bus.
Segments can be joined together using repeaters or bridges.
GLOSSARY
serial interface
529
Hardware for sending and receiving data one bit at a time.
SMDR
Station Message Detail Recording. A stream of call data from the
telephone system. Typically, the data is not stored on the telephone
system itself. Rather, it is captured by an external device that connects to
the telephone system through an RS232 port.
SMTP
Simple Mail Transfer Protocol. The TCP/IP standard protocol for
transferring electronic mail messages from one machine to another. SMTP
specifies how two mail systems interact and the format of control
messages they exchange to transfer mail.
SNA
STP
Supervisory
Monitoring
switched Ethernet
system-wide
greetings
Systems Network Architecture. IBM’s layered communications protocol
for sending data between IBM hardware and software.
Shielded Twisted Pair. A twisted pair of wires surrounded by a shield that
is typically made of braided wire or metal foil.
A facility that allows a supervisor to monitor incoming calls to agents
while those calls are in progress.
An Ethernet network that allows each user the full Ethernet bandwidth of
10 Mbit/s to another node.
A special type of time-dependent greeting that is used throughout the
system.
T
T1/E1
T3
TAPI
A high-speed data channel that can manage 24 voice or data channels
(T1) or 30 voice or data channels (E1) at 64Kbit/s. Refers to the U.S. T1
line or European E1 equivalent.
A U.S. standard for high-speed data transmission at 44.736 Mbit/s,
providing the equivalent bandwidth of 28 T-1 circuits. The carrier channel
can manage 672 voice or data channels.
Telephony Applications Programming Interface
A Microsoft Windows standard interface for integration between
telephone systems and Windows-based software. A typical example is
integrating Caller ID with a database on your computer that contains
detailed information about potential callers. When your telephone rings,
a window displays on your computer with information about the caller.
530
GLOSSARY
TCP/IP
thin Ethernet
time-dependent
greeting
Transmission Control Protocol/Internet Protocol. The suite of protocols
that define how to move information over the Internet.
An 802.3 LAN that uses smaller than normal diameter coaxial cable; often
used to link PCs together. Also known as 10BASE2.
Greetings that usually indicate the time of day that the caller is calling
(morning, afternoon, evening) and are an optional feature of the
Automated Attendant.
toll-free
The U.S. term for “free phone.”
toll restrictions
The U.S. term for “call barring.”
translation
trunk
twisted pair
The process of interpreting or modifying dialed digits for incoming or
outgoing calls and allows the call to progress through the network.
A communications channel between two points. It often refers to
large-bandwidth telephone channels between major switching centers,
capable of transmitting many simultaneous voice and data signals.
Two insulated wires twisted together with the twists varied in length to
reduce potential signal interference between the pairs. Twisted pair is the
most common medium for connecting telephones, computers and
terminals.
U
UPS
Uninterruptible Power Supply. A secondary power source attached to a
piece of hardware, for example a server, which provides backup power
for conducting an orderly shutdown if the server’s normal power supply
fails.
UTP
Unshielded Twisted Pair. Two insulated wires twisted together with the
twists varied in length to reduce potential signal interference between the
pairs. The standard cabling used for telephone lines and Ethernet
10BASE-T.
V
virtual LAN
A logical, rather than a physical, LAN that includes workgroups drawn
together for business reasons or for a particular project regardless of the
location of the members.
GLOSSARY
VPIM
VTL
531
Voice Profile for Internet Mail. A set of Internet protocols that merges
voice messaging and e-mail. VPIM lets voice mail and e-mail servers
exchange messages across TCP/IP-based intranets and the Internet.
Virtual Tie LIne. Allows several domains to create tie lines on demand and
to place calls over a WAN. Uses peer-to-peer connections for the audio.
W
WAN
Wide Area Network. A network that covers a larger geographical area
than a LAN. In a WAN, telecommunications links are normally leased from
the appropriate Public Telephone Operator (PTO).
wiring closet
The location, usually a physical box, in which the cabling on one floor of a
building is terminated.
workstation
Another name for a computer, typically running UNIX or the Windows NT
operating system.
532
GLOSSARY
INDEX
Symbols
*
character in VTL caller ID 301
Numbers
3Com 3101B/3102B Business telephone
LUI menu options 425
3Com 3103 Manager’s telephone
bridged station appearance restrictions 120
button mapping restrictions 123
LUI menu options 425
3Com IP Conferencing Module 254
4ESS protocol 304
call-by-call service 185
selecting 178
4-Port Analog Terminal Card
adding 126
911
and account codes 44, 47
and caller ID 471
and Class of Service 133
sample dial plan 472
A
access buttons
Attendant Console 122
mapping 114
access digit 203
account codes 43
and emergency calls 44, 47
and system features 44
in Call Detail Reporting (CDR) 47
ACD
agents 150
and SIP (Session Initiation Protocol) 243
announcements 148, 251
Call Data Reports 145
circular groups 137
defined 135
estimated wait time 140
extending wrap-up time 144
functions explained 147
group defined 135
hardware limits 145
licenses 138
linear groups 136
most idle agent groups 137
overriding wrap-up time 143
port contention 152
statistics 151
wrap-up time 143
adding
4-Port Analog Terminal Card 126
ATAs 128
Attendant Console 121
Digital Line Card groups 179
extension lists 296
mirror disk 87
telephones 93 to 95
address, IP
Call Processor 425, 429
configuring DHCP server to provide Call
Processor’s IP address 461
gateway 425, 429
viewing 425
address, MAC
specifying from a telephone 425, 429
viewing in telephone diagnostics 425, 429
administrator password 79
agents
ACD 150
SNMP 377
alarms, Digital Line Cards 438
analog devices
and caller ID 466
connecting 126
Analog Line Card
audio gain controls 163
timing parameters 163
Analog Terminal Adapter (ATA)
adding 128
and TTY devices 221
modifying 129
removing 129
status 129
534
INDEX
Analog Terminal Card (ATC)
and TTY devices 221
audio gain controls 130
connecting analog devices 126
timing parameters 130
announcements
ACD 148, 251
estimated wait time 140
in-queue digit 142
open and closed 142
ATA (Analog Terminal Adapter)
adding 128
modifying 129
removing 129
status 129
ATC (Analog Terminal Card)
and TTY devices 221
audio gain controls 130
connecting analog devices 126
timing parameters 130
Attendant Console
3103 Manger’s telephone restrictions 120, 123
access buttons 122
adding 121
bridged station appearances restrictions 120
command line interface commands 125
configuring 120
Feature buttons 122
modifying 121
removing 122
using a serial port connection to configure 124
audio gain controls
4-Port Analog Line Card 163
Analog Terminal Card (ATC) 130
audio recording
Music on Hold (MOH) 112
on other than NBX Telephones 113
phones with different settings 112
remote telephones 112
audio settings 34
changing, system-wide 338
Auto Discovery
Analog Line Cards 159
Analog Terminal Cards 27
Attendant Console 120
BRI-ST Digital Line Card 167
E1 channel numbering 182
enabling and disabling 28
first extension used 316
telephones 93, 281
Automated Attendant
activating changes 221
adding 210
button assignments 219
buttons 217
configuring 210
default functions 213
default timeout 209
dial by extension 209
dial by name 209
examples 216
extension range 288
greetings 212
importing
prompts 208
system-wide greetings 212
time-dependent greetings 212
modifying 224
overview 208
recording prompts 208
restoring defaults 225
testing 226
timeout 209
TTY voice mail 210, 221
voice application setup utility 225
Automated Attendant Setup Utility
default password 226
automatic
callback timeout 41
line card port configuration 160
reboot 84
B
Barge-In mode 60, 361
battery
replacing on Call Processor 449
brackets
attaching to the telephone 94
bridged extensions
and caller ID 467
and Camp On feature 109
and TAPI Route Points 357
defining 101
mapped extensions report 108
modifying on the primary telephone 107
on the primary telephone 102
on the secondary telephone 103
overview 98
restrictions 120
sample calling situations 107
sample configurations 100
BRI-ST Digital Line Cards
connecting 170
status lights (LEDs) 172
browsers, supported 22
INDEX
business information 32
business hours and CoS (Class of Service) 32
modifying 32
modifying business hours 32
modifying system mode 32
Busy Lamp/Speed Dial
mapping buttons 116
buttons, Automated Attendant 217
Disabled 219
Enter Submenu 221
Exit Menu 220
Name Directory 219
Prompted Transfer 220
Reserved in Dial Plan 220
Single Digit Transfer 220
System Disconnect 219
Transfer to TTY Voice Mail 220
Transfer to Voice Mail 219
buttons, telephone
locking 115
mapping 113
testing 432
C
call coverage
for hunt groups 156
Call Detail Reports
and Caller ID from VTLs 301
enabling 47
purging data 83, 84
Call Park
adding extensions 51
and caller ID 469
and TAPI Route Points 357
changing extension name 51
configuring 51
extension range 289
removing extensions 51
timeout 40
Call Pickup 49
Call Privacy 57
call processing
inbound 263
outbound 263
Call Processor
IP address 425, 429
configuring DHCP server to provide 461
specifying the MAC address from a
telephone 425, 429
status lights 174
Call Reports
capabilities 80
535
configuring 83
installing 83
call restrictions 132
call timer
enabling system-wide 28
feature interaction 29
call-by-call service 185
caller ID
and 911 471
and analog ports 466
and bridged extensions 467
and Call Park 469
and CDR date from VTLs 301
and Hunt Groups 469
and Legacy Link 467
and TAPI 469
and VTL calls 469
external calls 467
forwarded calls 465
overview 465
VTL pretranslator 301
wait timer 28
calling access permissions 132
Camp On
restrictions with bridged extensions 109
timeout 41
Central Office (CO)
code 134
Digital Line Card status light 173
channel service unit 187
channels
modifying 182
removing from a Digital Line Card group 182
status 183
Class of Service (CoS)
and 911 133
and hunt groups 134
override 133
speed dial numbers 133
user settings 132
CLIR
and VTL call pretranslators 301
CO (Central Office)
code 134
Digital Line Card status light 173
command line interface commands
for configuring a 3105 Attendant Console 125
community strings 378
conferences
public 254
restricted 254
restrictions in SIP mode 236
timeout 40
536
INDEX
configuration file, dial plan 264, 277
configuring
Attendant Console 124
automated attendant 210
BRI-ST Digital Line Card 172
Digital Line Card groups 170
line card port 160
contention
ACD with voice mail ports 152
conventions
notice icons 18
cordless telephones 126
CoS (Class of Service)
and 911 133
and hunt groups 134
override 133
speed dial numbers 66, 133
user settings 132
creating
bridged extensions report 108
dial plan configuration file 278
dial plan reports 284
D
database operations
migrating data 87
purging 84
purging CDR data 84
restoring 76
date and time settings 33
DDI (Direct Dialing Inward) services
dial plan configuration 166
delayed ringing pattern 116
DHCP
configuring option 184 461
diagnostics
LUI (local user interface) 415
telephone 415
telephone buttons 432
telephone LEDs (status lights) 428, 431
dial by extension 209
dial by name 209
dial plan
3-digit and 4-digit 286
and 911 471
and Enhanced 911 (E911) 274
configuration file 264, 277
4ESS protocol 304
accessing 278
commands 309
creating 278
DDI/MSN services for BRI 166
translator entries for BRI 166
configuring VTLs 339
default Auto Extension 316
exporting 282
extension settings 286
extension settings (table) 288
External Keyset Prefix 315
first Auto Discover Extension 316
Hybrid mode 266
importing 281
Keyset mode 266
modifying 285
off-site notification 267
overview 261
pretranslators 265, 300
report 284
routing 265
sample 472
sample solutions 324
settings
changing 290
tables 262, 267
incoming 272
internal 272
testing 283
timed routes 283
VPIM configuration 307
VTL configuration 333
VTL password 351
VTLs and site-unique extensions 339
VTLs with site codes 341
dial prefix settings 286
dial tone 192
Digital Line Cards
adding groups 179
alarms 438, 439
BRI-ST status lights (LEDs) 172
channel status 183
configuring 172
connecting BRI-ST Digital Line Cards 170
download status lights 174
E1 status lights (LEDs) 173
groups
configuring 170
membership status 171
modifying membership 180
inserting (caution) 168
model number 444
modifying 175
channels 182
groups 179
IP settings 184
removing 185
INDEX
channels 182
groups 182
status lights (LEDs) 173, 439
T1 status lights (LEDs) 173
Direct Dialing Inward (DDI) services
dial plan configuration 166
disabling transfer prompt 200
disk mirroring 374
adding mirror disk 87
overview 87
replacing disk 90
reverting to a single disk 90
status lights (LEDs) 89
disk status 374
DNS 234
Do Not Disturb
and TAPI Route Points 356
documentation 364
domains 54
and supervisory monitoring 54
and WhisperPage 68
downloads
applications 363
Digital Line Card status lights (LEDs) 174
Label Maker 363
NBX Call Reports 363
NBXTSP (NBX TAPI Service Provider)
software 451
dual power supply 374
E
E1 Digital Line Cards
status lights (LEDs) 173
E911 (Enhanced 911)
and dial plans 274
and SIP (Session Initiation Protocol) 238
ISDN PRI signaling 164
echo suppression 34
e-mail, configuring for IMAP 202
emergency calls
and account codes 44, 47
and caller ID 471
and dial plans 274
and SIP (Session Initiation Protocol) 238
Class of Service 133
dial plan example 472
ISDN PRI signaling 164
Enhanced 911 (E911)
and dial plans 274
and SIP (Session Initiation Protocol) 238
ISDN PRI signaling 164
errors 444
estimated wait time 140
Ethernet (Layer 2) 31
event logs, viewing
Adminlog 406
upgrade log 407
exporting dial plan 282
extension length 288
extension lists 294
adding 296
managing 286
modifying 297
removing 298
updating for VTLs 342
extension numbers
adding Call Park 51
changing Call Park 51
changing settings 292
line card port 291
managing 286
phantom mailbox 291
removing Call Park 51
extension ranges
Automated Attendant 288
Call Park 289
changing 290
external extensions 289
for VTLs 334
hunt groups 289
telephones 288
extension settings, dial plan 286
Extensions Start at 28
external calls, and caller ID 467
external extensions, extension ranges 289
External Keyset Prefix, dial plan 290, 315
External Paging Delay 28
External Paging Volume 28
External Prefix 28
F
factory defaults 84
fax machines 126
Feature buttons
Attendant Console 122
feature codes 364
ACD Wrap-Up timer override 143
and hunt groups 154
and supervisory monitoring 59
Class of Service (CoS) override 133
extending ACD Wrap-Up time 144
for supervisory monitoring 407
guide 364
Other function 114
537
538
INDEX
speed dial with account codes 46
WhisperPage 66
forward voice mail timeout 40
forwarded calls, caller ID 465
G
Gateway IP Address 425, 429
greetings
Automated Attendant 212
example 216
importing 208
main menu example 216
recording 212
H
H3PingIP 434
Handsfree on Internal Transfer 28
hexadecimal codes
ISDN completion codes 455
hop off
enabling 350
hot desking 237, 240
hunt groups
and caller ID 469
and Class of Service (CoS) 134
and supervisory monitoring 157
and TAPI Route Points 357
calling groups 154
circular 154
configuring 135, 154
extension range 289
linear 154
telephone priority 155
Hybrid mode
button mapping 114
dial plan 266
I
IGMP (Internet Group Management Protocol) 41
IMAP (Internet Message Access Protocol) 201
configuring an e-mail client 202
importing
International dial plan 280
North American dial plan 279
prompts 209, 214
system-wide greetings 212
time-dependent greetings 212
user-defined dial plan 281
inbound call processing 263
incoming calls
DDI/MSN for BRI-ST 166
pretranslator 275
incoming dial plan table 272
In-Queue Digit Hot Key 142
internal dial plan table 272
international dial plan, importing 280
international terminology 18
Internet Group Management Protocol (IGMP) 41
Internet Message Access Protocol (IMAP) 201
configuring an e-mail client 202
IP address
configuring from a DHCP server 461
viewing 425
IP bins
changing 42
multicast 42
IP On-the-Fly 31
IP settings
modifying 184
ISDN completion cause codes (table) 455
K
key pad button actions 219
Keyset mode
dial plan 266
prefix 290
L
LabelMaker 363
Least Cost Dial Plan table 273
LEDs (status lights)
BRI-ST Digital Line Cards 172
Digital Line Card downloads 174
disk mirroring 89
E1 Digital Line Cards 173
T1 Digital Line Cards 173
telephone diagnostics 428, 431
testing on the telephone 431
wrap-up time 143
Legacy Link, caller ID 467
licenses
ACD 138
and restoring a database 76
status 365
viewing 365
line card port 159
configuring 160
extension number 291
modifying 162
rebooting 163
removing 162
INDEX
status 163
line pool 113
line port hold timeout 40
locking
buttons 115
hunt group members 155
logging
maximum file size 187
LUI (Local User Interface)
3101B/3102B Business telephone menu
options 425
3103 Manager’s telephone menu options 425
and PoE 416
diagnostic/configuration utility 415
M
MAC address
specifying NCP address from a telephone 425,
429
viewing in telephone diagnostics 425, 429
mailbox, phantom
extensions 291
main menu
default functions 213
greetings example 216
main menu window, NetSet utility 22
maintenance alerts
configuring the sender 407
mapping buttons
access 114
Attendant Console 122
Busy Lamp/Speed Dial 116
Other 114
telephone groups 115, 117
Media Driver, and third-party messaging 451
menu time-out action 219
menu tree dialog box 213
message storage capacity, viewing 200
messages
maximum length allowed 199
maximum number allowed 198
retaining 199
messaging, voice
overview 198
phantom mailboxes 131
third-party 451
MIBs 382
modifying
ATA 129
Attendant Console 121
Auto Attendant 224
bridged extensions 107
539
channels 182
dial plan 285
Digital Line Cards 175
channels 182
groups 179, 180
IP settings 184
extension lists 297
line card ports 162
system settings 41
administrator password 79
advanced regional settings 412
audio settings 34
Auto Attendant password 79
date and time 33
disk mirroring 87
multicast addresses 41
regional settings 412
reverting to single disk 90
ringing patterns 53
speed dial numbers 53
system mode 32
TAPI telephony 361
timers 40
MOH (Music on Hold) 28
configuration 250
legal disclaimer 113, 249
Monitor mode 59, 360
MOT (Music on Transfer) 28
configuration 250
multicast addresses
changing IP addresses 42
changing IP bins 42
overview 41
Music on Hold (MOH) 28
configuration 250
legal disclaimer 113, 249
Music on Transfer (MOT) 28
configuration 250
N
NAPT (Network Address Port Translation) 97
NAT overloading 97
NBX Call Reports software 363
NBX Messaging 28
NBX TAPI Service Provider (NBXTSP) software 451
NBXTSP (NBX TAPI Service Provider) software 451
NCP
IP Address 425, 429
MAC Address 425, 429
status lights 174
NetSet utility 22
Network Address Port Translation (NAPT) 97
540
INDEX
network protocol
Ethernet only 31
IP On-the-Fly 31
standard IP 31
North American dial plan, importing 279
notice icons 18
Number
telephone button mapping 114
O
off-site notification 205
behavior 206
configuring 205
dial plan 267
enabling 205
One Button Transfer 28
operators
access digit 203
Option 184, configuring on DHCP server 461
Other function 114
outbound call processing 263
outgoing calls
pretranslator 276
overriding
button mappings 134
Class of Service (CoS) 133
P
passwords
administration 79
administrator 79
default for SIP user extensions 259
voice mail 201
PBX connections
supplying dial tone 192
Periodic Timestamp On Console (PTOC) 406
permissions 132
phantom mailbox
and TAPI Route Points 357
creating 132
extensions 291
overview 131
play/record extension
where to specify 211
Port Usage, voice mail 207
power supply, dual 374
powered Ethernet cable
and LUI 416
pretranslators 274
assigning 300
dial plan 265, 274
incoming calls 275
managing in dial plan 300
optional for VTLs 343
outgoing calls 276
removing from dial plan 304
viewing devices 300
VTL calls and caller ID 301
privacy list
explained 57
prompts 208
defining 213
importing 208
recording for Automated Attendant 208
TTY format 221
Prty
telephone button mapping 114
PTOC (Periodic Timestamp On Console) 406
Pulse Dialing, enabling 28
Q
Quick Reference Guides, viewing 364
R
rebooting
automatically 84
line card port 163
telephones 96
recording
time-dependent greetings 212
redialing, dial prefix settings 286
redirected call 356
regional settings 412
removing
ATAs 129
Attendant Console 122
channels 182
Digital Line Card groups 182
Digital Line Cards 185
extension lists 298
line card port 162
pretranslators 304
telephone groups 110
telephones 96
replacing
failed disk 90
NCP battery 449
reports
bridged extensions 108
calls 80
dial plan 284
system data 374
INDEX
system devices 373
system directory 373
rerouting, VTL calls 346
restoring factory defaults 84
RFC 1889 235
RFC 3261 235
Ring
telephone button mapping 115
ringing patterns 53
Route Point
system capacities 358
routing dial plan 265
RTP DTMF Payload Type 28
RTP RFC support 235
S
SDN (Software Defined Networks) 304
security
passwords 79
serial number, telephone 425, 429
serial port
configuring a 3105 Attendant Console 124
Session Initiation Protocol (SIP)
and ACD 243
conferencing 254
default user extension password 259
enabling 29
Enhanced 911 (E911) 238
hot desking 237, 240
public conferences 254
restricted conferences 254
RFC 3261 235
sessions 241
silence suppression 39
system-wide 34
Simple Mail Transfer Protocol (SMTP) 231, 234
Simple Network Management Protocol (SNMP)
agents 377
community strings 378
disabling 375
enabling 375
informs 380
managers 377
notifications 380
security 378
traps 380
SIP (Session Initiation Protocol)
and ACD 243
conferencing 254
creating mailboxes 247
default user extension password 259
enabling 29
Enhanced 911 (E911) 238
hot desking 237, 240
public conferences 254
restricted conferences 254
RFC 3261 235
sessions 241
site codes
pretranslator for caller ID 301
using for VPIM 306
using for VTLs 335
SMTP (Simple Mail Transfer Protocol) 231, 234
SNMP (Simple Network Management Protocol)
agents 377
community strings 378
disabling 375
enabling 375
informs 380
managers 377
notifications 380
security 378
traps 380
software
NBX Call Reports 363
NBX Label Maker 363
NBXTSP (NBX TAPI Service Provider) 451
Telephone Local Configuration (TLC)
application 363
version number 429
Software Defined Networks (SDN) 304
speed dial numbers 53
Class of Service 133
mapping 116
standard IP 31
statistics
ACD 151
TAPI Route Point 359
voice mail port usage 207
voice mail user usage 207
status
ATA 129
BRI group membership 171
Digital Line Card troubleshooting 436
disk 90, 374
dual power supply 374
licenses 365
line card port 163
telephones 96
status lights (LEDs) 173, 439
BRI-ST Digital Line Cards 172
testing on the telephone 428
wrap-up time 143
submenus for greetings 216
subnet mask 31
541
542
INDEX
supervisory monitoring
and TAPI 359
Barge-In mode 361
button mapping 59
Call Privacy 57
changing agents 60
default tones 58
domains 54
enabling 28
Monitor mode 360
Privacy List 57
usage notes 62
using Feature Code 425 59
using passwords 54
Whisper mode 361
system database 264
system level operations
installing licenses 366
system mode 32
system settings
advanced regional settings 412
audio settings 34
Auto Attendant password 79
business hours 32
business information 32
date and time 33
disk mirroring 87
multicast addresses 41
regional settings 412
reverting to single disk 90
ringing patterns 53
speed dial numbers 53
TAPI telephony 361
timers 40
viewing 30
system-level operations
installing software upgrades 368
managing data 84
viewing event logs 406
System-wide CLIR 28
system-wide greetings 212
system-wide settings 28
T
T1 Digital Line Cards
status lights (LEDs) 173
TAPI (Telephony Application Programming Interface)
and caller ID 469
maximum clients 361
Route Point 356
supervisory monitoring 359
support for SIP 238
system settings for 361
TAPI Line Redirect Timeout 41, 359
TAPI Route Point
statistics 359
system capacities 358
telephone
adding 93 to 95
analog 126
Auto Discovery 93
button mappings 113
connections 434
cordless 126
diagnostics 415
extension length 288
extension range 288
locking buttons 115
rebooting 96
status 96
viewing MAC address through 425, 429
telephone groups
access Button types 114
call recording and monitoring 110
changing names 110
creating 110
locking buttons 115
mapping buttons 115, 117
removing 110
Telephone Local Configuration (TLC)
application 363, 433
Telephony Application Programming Interface (TAPI)
and caller ID 469
maximum clients 361
Route Point 356
supervisory monitoring 359
support for SIP 238
system settings for 361
TEP log 407
maximum file size 187
terminology, international 18
testing
Automated Attendant 226
dial plan 283
telephone buttons 432
telephone connections 434
telephone LEDs (status lights) 428, 431
third-party messaging 29, 451
third-party telephones 372
time-dependent greetings
adding 212
example 216
importing 212
recording 212
timers
INDEX
automatic callback 41
call park 40
caller ID 28
Camp On 41
conference 40
forward voice mail 40
line port hold 40
TAPI line redirect 41
transfer 40
timestamp 406
timing parameters
4-Port Analog Line Card 163
4-Port Analog Terminal Card 130
TLC (Telephone Local Configuration)
application 363, 433
transfer prompt, disabling 200
transfer timeout 40
troubleshooting 434
TTY voice mail 201, 220, 221
prompt repetitions 211
U
upgrading software 368
migrating data 87
URL for user access to IP Messaging 29
User Usage, voice mail 207
USER_ALERTING_NO_ANSWER 444
User-based Security Model (USM) 379
USM (User-based Security Model) 379
V
V3001R systems
disk mirroring 374
dual power supply 374
V5000 systems
disk mirroring 374
dual power supplies 374
VCAM (View-based Access Control Model) 379
version number, software 429
View-based Access Control Model (VCAM) 379
voice application setup utility 225
voice mail 198
creating a phantom mailbox 132
extensions 201
incoming call behavior 200
password 201
phantom mailboxes 131
port usage 207
storage space 200
transferring calls to 219
TTY automated attendant 221
TTY prompts 220
user usage 207
VPIM (Voice Profile for Internet Mail)
advanced settings 231
configuring DNS server information 234
configuring the dial plan for 307
control parameters 228
operations management 229
overview 227
statistics 230
using unique extension ranges 306
VTL (Virtual Tie Line) 333
audio compression option 349
configuring 338
dial plan configuration 339
license installation 338
managing VTLs 348
modifying name of 348
Music on Hold (MOH) 354
password configuration 351
password in dial plan 351
rerouting VTL calls 346
silence-suppression option 350
statistics 348
system software compatibility 333
toll calls 354
troubleshooting 354
unique extension ranges 334
using site codes 335
verifying access to remote system 345
verifying local system operation 344
verifying operation of 344
VTL calls
and caller ID 469
pretranslator for caller ID 301
rerouting 346
W
Whisper mode 60, 361
WhisperPage 66
and domains 68
and other features 69
feature code 66
permissions 68
restrictions 70
wrap-up time 143
ACD agent override 143
agent extend 144
LEDs or LCDs 143
543
544
INDEX
3Com Corporation LIMITED WARRANTY
HARDWARE
3Com warrants this hardware product to be free from defects in workmanship and materials, under normal
use and service, for the following length of time from the date of purchase from 3Com or its authorized
reseller:
3Com’s sole obligation under this express warranty shall be, at 3Com’s option and expense, to repair the
defective product or part, deliver to Customer an equivalent product or part to replace the defective item, or
if neither of the two foregoing options is reasonably available, 3Com may, in its sole discretion, refund to
Customer the purchase price paid for the defective product. All products that are replaced will become the
property of 3Com. Replacement products may be new or reconditioned. 3Com warrants any replaced or
repaired product or part for ninety (90) days from shipment, or the remainder of the initial warranty period,
whichever is longer.
SOFTWARE
3Com warrants that each software program licensed from it will perform in substantial conformance to its
program specifications, for a period of ninety (90) days from the date of purchase from 3Com or its
authorized reseller. 3Com warrants the media containing software against failure during the warranty period.
No updates are provided. 3Com's sole obligation under this express warranty shall be, at 3Com's option and
expense, to refund the purchase price paid by Customer for any defective software product, or to replace any
defective media with software which substantially conforms to applicable 3Com published specifications.
Customer assumes responsibility for the selection of the appropriate applications program and associated
reference materials. 3Com makes no warranty or representation that its software products will meet
Customer’s requirements or work in combination with any hardware or applications software products
provided by third parties, that the operation of the software products will be uninterrupted or error free, or
that all defects in the software products will be corrected. For any third party products listed in the 3Com
software product documentation or specifications as being compatible, 3Com will make reasonable efforts to
provide compatibility, except where the non-compatibility is caused by a “bug” or defect in the third party's
product or from use of the software product not in accordance with 3Com’s published specifications or user
manual.
YEAR 2000 WARRANTY
In addition to the Hardware Warranty and Software Warranty stated above, 3Com warrants that each
product sold or licensed to Customer on and after January 1, 1998 that is date sensitive will continue
performing properly with regard to such date data on and after January 1, 2000, provided that all other
products used by Customer in connection or combination with the 3Com product, including hardware,
software, and firmware, accurately exchange date data with the 3Com product, with the exception of those
products identified at 3Com’s Web site, tap://www.3com.com/products/yr2000.html, as not meeting this
standard. If it appears that any product that is stated to meet this standard does not perform properly with
regard to such date data on and after January 1, 2000, and Customer notifies 3Com before the later of April
1, 2000, or ninety (90) days after purchase of the product from 3Com or its authorized reseller, 3Com shall,
at its option and expense, provide a software update which would effect the proper performance of such
product, repair such product, deliver to Customer an equivalent product to replace such product, or if none
of the foregoing is feasible, refund to Customer the purchase price paid for such product.
Any software update or replaced or repaired product will carry a Year 2000 Warranty for ninety (90) days
after purchase or until April 1, 2000, whichever is later.
OBTAINING WARRANTY
SERVICE
Customer must contact a 3Com Corporate Service Center or an Authorized 3Com Service Center within the
applicable warranty period to obtain warranty service authorization. Dated proof of purchase from 3Com or
its authorized reseller may be required. Products returned to 3Com's Corporate Service Center must be
pre-authorized by 3Com with a Return Material Authorization (RMA) number marked on the outside of the
package, and sent prepaid and packaged appropriately for safe shipment, and it is recommended that they
be insured or sent by a method that provides for tracking of the package. The repaired or replaced item will
be shipped to Customer, at 3Com's expense, not later than thirty (30) days after 3Com receives the defective
product.
Dead- or Defective-on-Arrival. In the event a product completely fails to function or exhibits a defect in
materials or workmanship within the first forty-eight (48) hours of installation but no later than thirty (30)
days after the date of purchase, and this is verified by 3Com, it will be considered dead- or
defective-on-arrival (DOA) and a replacement shall be provided by advance replacement. The replacement
product will normally be shipped not later than three (3) business days after 3Com’s verification of the DOA
product, but may be delayed due to export or import procedures. When an advance replacement is provided
and Customer fails to return the original product to 3Com within fifteen (15) days after shipment of the
replacement, 3Com will charge Customer for the replacement product, at list price.
3Com shall not be responsible for any software, firmware, information, or memory data of Customer
contained in, stored on, or integrated with any products returned to 3Com for repair, whether under
warranty or not.
WARRANTIES EXCLUSIVE
IF A 3COM PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY FOR
BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE
PAID, AT 3COM'S OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND
REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, TERMS, OR CONDITIONS,
EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES, TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
SATISFACTORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGEMENT, ALL OF
WHICH ARE EXPRESSLY DISCLAIMED. 3COM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR
USE OF ITS PRODUCTS.
3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT
THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND
THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OTHER HAZARDS, OR ACTS OF
GOD.
LIMITATION OF LIABILITY
TO THE FULL EXTENT ALLOWED BY LAW, 3COM ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY
LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR
PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT
OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF ITS PRODUCTS, EVEN IF 3COM OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE
PURCHASE PRICE PAID, AT 3COM'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE
AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
DISCLAIMER
Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the
limitation of incidental or consequential damages for certain products supplied to consumers, or the
limitation of liability for personal injury, so the above limitations and exclusions may be limited in their
application to you. When the implied warranties are not allowed to be excluded in their entirety, they will be
limited to the duration of the applicable written warranty. This warranty gives you specific legal rights which
may vary depending on local law.
GOVERNING LAW
This Limited Warranty shall be governed by the laws of the State of California, U.S.A. excluding its conflicts of
laws principles and excluding the United Nations Convention on Contracts for the International Sale of
Goods.
3Com Corporation
5400 Bayfront Plaza
Santa Clara, CA 95054
(408) 326-5000
FCC CLASS A VERIFICATION STATEMENT
WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules, and the Canadian Department of Communications Equipment
Standards entitled, “Digital Apparatus,” ICES-003. These limits are designed to provide reasonable protection
against harmful interference in a commercial installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case, the user will be required to correct the interference at the user’s own
expense.
Changes or modifications not expressly approved by 3Com could void the user’s authority to operate this
equipment.
FCC CLASS B STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired
operation.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules, and the Canadian Department of Communications Equipment
Standards entitled, “Digital Apparatus,” ICES-003. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from the one which the receiver is connected to.
■
Consult the dealer or an experienced radio/TV technician for help.
The user may find the following booklet prepared by the Federal Communications Commission helpful:
The Interference Handbook
This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock No.
004-000-00345-4.
NOTE: In order to maintain compliance with the limits of a Class B digital device, 3Com requires that you use
quality interface cables when connecting to this device. Changes or modifications not expressly approved by
3Com could void the user’s authority to operate this equipment. Refer to the manual for specifications on
cabling types.
FCC DECLARATION OF CONFORMITY
We declare under our sole responsibility that the
Model:
3CXXX
Description:
Product Name
to which this declaration relates, is in conformity with the following standards or other normative documents:
■
ANSI C63.4-1992 Methods of Measurement
■
Federal Communications Commission 47 CFR Part 15, subpart B
15.107 (a) Class B Conducted Limits
15.109 (a) Class B Radiated Emissions Limits
■
15.107 (e) Class B Conducted Limits
15.109 (g) Class B Radiated Emissions Limits
3Com Corporation, 5400 Bayfront Plaza, P.O. Box 58145, Santa Clara, CA 95052-8145
Download PDF
Similar pages