Pocket Mod™
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your unit and 19 character product I.D. with you before
contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
CONTENTS
Safety Warnings............................................................................................1-2
Before You Begin.............................................................................................. 3
Assembly and Set-Up....................................................................................4-6
Charging Battery/Pre-ride Checklist................................................................. 7
Usage................................................................................................................ 8
Repair and Maintenance.............................................................................8-11
Troubleshooting Guide.................................................................................... 12
Pocket Mod Parts............................................................................................ 13
Warranty......................................................................................................... 15
SAFETY WARNINGS
WARNING: Riding a Pocket Mod does present potential risks and
caution is required. Like any riding product, the Pocket Mod has inherent
hazards associated with its use (for example, falling off or riding it into a
hazardous situation). Like any riding product, the Pocket Mod can and is
intended to move and it is therefore, of course, possible to lose control or
otherwise get into dangerous situations. Both children and adults responsible
for supervising them must recognize that if such things occur, a rider can
be seriously injured or die, even when using safety equipment and other
precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations, which may
affect the locations where the Pocket Mod may be used. Keep safely
away from cars and motor vehicle traffic at all times, and only use
where allowed and with caution.
Do not activate the speed control on the hand grip unless you are on the
Pocket Mod and in a safe, outdoor environment suitable for riding.
The normal powered top speed of the Pocket Mod will be approximately 15
mph (24 kmh), which can be affected by conditions, such as rider weight,
inclines, tire inflation and battery charge level. Avoid excessive speeds that
can be associated with downhill rides.
WARNING: PARENTAL AND ADULT
RESPONSIBILITY AND SUPERVISION IS NECESSARY:
Because products, like the Pocket Mod, can and do present potential hazards
plainly associated with their use, it is well recognized THE NEED FOR
EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING PRODUCTS
APPROPRIATE TO THE AGE OF A CHILD, OR PARENTAL SUPERVISION IN
SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES MAY HAVE ACCESS
TO THE SAME RIDING PRODUCTS, IS IMPORTANT. Not every product is
appropriate for every age or size of child, and different age recommendations
are found within this category of product which are intended to reflect the
nature of the hazards and the expected mental or physical ability, or both, of a
child to cope with the hazards.
Maintain a hold on the handlebars at all times. Do not touch the brakes or
motor on your Pocket Mod when in use or immediately after riding as these
parts can become very hot.
Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
The Pocket Mod is intended for use on flat, dry surfaces, such as pavement or
level ground, without loose debris, such as sand, leaves, rocks or gravel. Wet,
slick, bumpy, uneven or rough surfaces may impair traction and contribute to
possible accidents. Do not ride your Pocket Mod in mud, ice, puddles or water.
Watch out for potential obstacles that could catch your wheel or force you
to swerve suddenly or lose control. Avoid sharp bumps, drainage grates, and
sudden surface changes.
The recommended minimum rider age is 13 and older. Any rider unable
to fit comfortably on the Pocket Mod should not attempt to ride it. A parent’s
decision to allow his or her child to ride this product should be based on the
child’s maturity, skill and ability to follow rules.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the Pocket Mod.
Do not attempt or do stunts or tricks on the Pocket Mod. The Pocket Mod is not
made to withstand abuse from misuse, such as jumping, curb grinding or any
other type of stunts. Racing, stunt riding, or other maneuvers also enhance risk
of loss of control, or may cause uncontrolled rider actions or reactions.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions and to be able to
understand the hazards inherent in Pocket Mod use, should not use or be
permitted to use products inappropriate for their abilities. Persons with heart
conditions, head, back or neck ailments (or prior surgeries to these areas of the
body), or pregnant women, should be cautioned not to operate such products.
Never allow more than one person at a time to ride the Pocket Mod.
Do not ride at night or when visibility is limited.
Never use near steps or swimming pools.
Do not allow hands, feet, hair, body parts, clothing, or similar articles to
come in contact with moving parts, wheels, or drivetrain, chain while the
motor is running.
DO NOT EXCEED THE WEIGHT LIMIT OF 170 lb (77 kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the Pocket Mod.
Never use headphones, a cell phone or text when riding.
CHECK AND MAINTAIN PRODUCT CONDITIONS
Never hitch a ride with a vehicle.
Before use, check to confirm that any and all chain guards or other
covers and guards are in place and in serviceable condition. Check that
the brake is functioning properly, and that tires are inflated properly and
have sufficient tread remaining. The Pocket Mod should be maintained and
repaired in accordance with the manufacturer’s specifications, using
only the manufacturer’s authorized replacement parts, and should not
be modified from the manufacturer’s original design and configuration.
Do not ride your Pocket Mod in wet or icy weather and never immerse
the Pocket Mod in water, as the electrical and drive components could be
damaged by water or create other possibly unsafe conditions. Never risk
damaging surfaces, such as carpet or flooring, by use of the Pocket Mod
indoors.
1
SAFETY WARNINGS
PROPER RIDING ATTIRE
Use only with the recommended charger.
Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads and kneepads. A helmet may be
legally required by local law or regulation in your area. A long-sleeved shirt,
long pants, and gloves are recommended. Always wear athletic shoes (lace-up
shoes with rubber soles) and keep shoelaces tied and out of the way of the
wheels, motor and drive system. Never ride barefooted or in sandals.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from Pocket Mod when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
Pocket Mod with damp cloth.
USING THE CHARGER
FAILURE TO USE COMMON SENSE AND HEED THE WARNINGS
INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE
CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.
The charger supplied with the Pocket Mod should be regularly examined for
damage to the cord, plug, enclosure and other parts. In the event of such
damage, the Pocket Mod must not be charged until the charger has been
repaired or replaced.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
2
BEFORE YOU BEGIN
Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect
the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping.
Because the Pocket Mod is 95 percent assembled and packed at the factory, there should not be any problems, even if
the box has a few scars or dents.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult.
Allow up to 15 minutes for assembly.
Allow up to 12 hours for initial charge (see page 7 for charging information).
Brake Lever
Throttle
On/Off
Switch
WARNING:
DO NOT USE NON-RAZOR
PRODUCTS WITH YOUR RAZOR
POCKET MOD.
The Pocket Mod has been built to
certain Razor design specifications.
The original equipment supplied at
the time of sale was selected on
the basis of its compatibility with
the frame, fork and all other parts.
Certain aftermarket products may
not be compatible and will void your
warranty.
Product I.D. Code:
Charger Port
1.Inside Storage Compartment
2.Underneath Frame
3.Charger
4.UPC Side of Box (not shown)
2. Underneath Frame
1. Storage Compartment
Under Seat
3. Charger
(Note: Charger design may vary
from one shown)
Kick Stand
Chain Guard
Required Tools
Plastic Bag Contents:
• Charger
• Tools
• Owner’s Manual
5 mm and 6 mm
Allen Wrenches
(Included)
Two (2) 13 mm/15 mm
Wrenches
(Included)
Spoke Tightener
(Included)
3
ASSEMBLY AND SET-UP
Note: Make sure the brake cables/
wires are out of the way before
inserting the handlebar into the fork.
Turn power switch off before conducting any maintenance procedures.
Attaching the Handlebars
Tool Required: One (1) 6 mm Allen wrench.
Steering Bolt
Wedge
1 Using a 6 mm Allen wrench, loosen steering bolt in four (4) complete turns
2 Facing the front of the Pocket Mod,
so that the wedge is loose and not touching steering tube.
position the handlebars so the throttle
is on your right and the lever brake
is on your left (the red “SAFE ZONE”
print will be facing you). Align wedge
inside handlebar tube. Note: Plastic
cover needs to be removed prior to
installing the handlebars.
WARNING: Periodically
check to make sure the steering bolt
is tightly fastened.
Note: Failure to secure the
handlebars within the safety zone
can cause the handlebars to come
out while riding.
Safety Zone
3a While inserting the steering
tube down into the handlebar tube,
hold steering bolt steady with
thumb and rotate handle bars 180
degrees to the left.
3b The throttle should now be
4 Slowly slide the handle bars up
on your left and the lever brake on
your right.
to make certain that the bar is in the
“SAFETY ZONE”. Failure to secure
the handlebars within the safety
zone can cause the handlebars to
come out while riding.
Steering Bolt
5 Securely tighten bolt using 6 mm
Allen wrench.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
4
ASSEMBLY AND SET-UP
Positioning the Brake Lever
Tool Required: One (1) 5 mm Allen wrench.
1 Adjust angle of the brake lever to
a comfortable position for the rider
by turning back and forth.
2 Securely tighten the bolt using a
5 mm Allen wrench.
Attaching the Front Wheel
Tools required: Two (2) 15 mm wrenches.
lock
washer
nut
1 Remove the plastic packing
material from the front fork.
2 Insert the wheel into the front
3 Insert the tab on the lock
fork with the lock washers on the
outside of the fork.
washer into the hole on the front
fork and tighten the nuts using two
15 mm wrenches.
Checking Spoke Tension
17
Spoke
Flange
Spoke
Nipple
18
Hub
Flange
Spoke
Flange
19
20
4
Rim
Nipple
1 Verify spoke tension by grasping and shaking each spoke. Spoke
3
2
1
2 Start with spoke closest to tire
should not be loose from hub. Look for any play between spoke flanges
where it mates with hub. Try to turn nipple using your fingers. You
should not be able to spin any nipple by hand. If one or more spokes
are loose, or if you can turn any nipple using your fingers, all spokes
must be checked and need to be tightened with a spoke tightener.
valve and tighten each nipple. In
sequence, exactly 1/4 to 1/2 turn.
A single 1/4 to 1/2 turn may not
be enough to bring the spokes into
proper tension. Continue tightening
all spokes in sequence, no more than
1/2 turn until all spokes are tight.
5
WARNING: Regularly check
the spoke tension and retighten
the spokes whenever loose. If you
have any doubt, ask an experienced
motorcycle or bicycle mechanic to
inspect your spokes to determine
if the spokes need tightening or
adjusting.
Note: Tightening each nipple more
than a 1/2 turn each can cause the
wheel to become distorted and
wobbly, thus permanently damaging
the wheel.
ASSEMBLY AND SET-UP
Inflating the Tires
Tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and
your purchase.
Using a bicycle tire pump equipped
for a Schrader valve, inflate the tires
to the PSI indicated on the sidewall
of the tires.
Light-up Valve Stem Caps
(select products only)
To activate the lights, unscrew the light from the cap base and insert three (3) AG10 Alkaline button cell
batteries (included) positive side down and re-attach the light to the cap base.
Remove existing valve stem cap from wheel and replace with light-up valve stem cap.
To replace the batteries, follow the same steps mentioned above. Discard old batteries in a responsible manner.
Note: The pressurized air supplies
found at gasoline stations are
designed to inflate high-volume
automobile tires. If you decide to
use such an air supply to inflate your
Pocket Mod tires, first make sure
the pressure gauge is working, then
use very short bursts to inflate to
the correct PSI. If you inadvertently
over-inflate the tires, release the
excess pressure immediately.
WARNING:
• Alkaline batteries included. Adult
supervision needed for installation
and disposing of batteries.
• Batteries should only be
replaced by an adult.
• Loose batteries could present
a choking hazard and should be
kept away from small children.
• Dispose of batteries properly.
• DO NOT mix old and new
batteries and DO NOT mix
alkaline, standard (carbon-zinc)
or rechargeable (ni-cad, ni-mh,
etc.) batteries.
Note: Make sure to install ALL THREE
(3) batteries positive (+) side down.
The lights are motion activated and
will only turn on when the product
is in motion.
Alkaline batteries are not
covered under the warranty.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
6
CHARGING THE BATTERY
Your Pocket Mod may not have a fully charged battery; therefore it is a good idea to charge the battery prior to use.
• Initial charge time: 12 hours.
• Recharge time: up to 12 hours, even if the light turns
green. Recommended maximum charging time is
24 hours.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended periods
of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure power switch is turned OFF when unit is not
in use. If the power switch is left on for an extended
period of time, the battery may reach a stage at which
it will no longer hold a charge.
• To ensure long battery life, never store the product in
freezing or below freezing temperatures! Freezing will
permanently damage the battery.
• Run time: Up to 40 minutes of continuous ride time.
Run time may vary depending on riding conditions, rider
weight, climate and/or proper maintenance.
• Constant stopping and starting may shorten ride time.
• Battery life can vary depending on proper maintenance
and usage of the unit.
WARNING: Use ONLY with
the recommended charger. Batteries
are only to be charged under adult
supervision. The charger is not a
toy. Always disconnect the charger
before wiping down and/or cleaning
the Pocket Mod with a damp cloth.
The charger supplied with the Pocket
Mod should be regularly examined
for damage to the cord, plug,
enclosure and other parts. In the
event of such damage, the Pocket
Mod must not be charged until it has
been repaired or replaced.
Chargers have built-in over-charge
protection to prevent battery from
being over-charged.
Note: If the charger gets warm
during regular use, this is a normal
response and is no cause for
concern. If your charger does not get
warm during use, it does not mean
that it is not working properly.
Charger
Wall outlet - Green (stand by)
Wall outlet and unit - Red (charging)
Wall outlet and unit - Green (charged)
LED Light
Note: Continue charging unit even if
light turns green prior to 12 hours.
Note: Make sure power is turned
OFF when unit is not in use. If
the power switch is left on for an
extended period of time, the battery
may reach a stage at which it will
no longer hold a charge.
2
1
Make sure the power switch
is in the OFF position. Plug the
charger into the charger port on the
product. The light on the charger
should turn red during charging. The
light will turn green when charging
is complete.
Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
WARNING: Failure to
recharge the battery at least once a
month may result in a battery that
will no longer accept a charge.
PRE-RIDE CHECK LIST
Brake
Hardware/Loose Parts
Tires
Safety Gear
Check the brake for proper function. When you squeeze the
lever, the brake should provide positive braking action. When
you apply the brake with the speed control on, the brake cut-off
switch will stop the motor.
Check and secure all fasteners before every ride. There should
not be any unusual rattles or sounds from loose parts or broken
components. If the unit is damaged, do not ride. Reference
“Safety Warnings” on page 1 of this manual.
Periodically inspect the tires for excess wear and replace as
needed. Regularly check the tire pressure and inflate as needed.
If you get a flat tire, the inner tube can be patched or a new tube
can be purchased from Razor or an authorized repair center.
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads, kneepads, pants and long sleeves are
recommended. Always wear closed toe shoes (lace-up with
rubber soles) and keep shoelaces tied and out of the way of the
wheels, motor and drive system. NEVER RIDE BAREFOOTED OR IN
SANDALS.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to run into a curb
or object and wreck, bend or break the frame. Get in the habit of
inspecting your product on a regular basis.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily
provide coverage for electric product use. Check with your
insurance company for information regarding insurance.
7
USAGE
Starting the Pocket Mod
Stopping the Pocket Mod
Place both hands on the handlebars. Slowly push forward with
one foot and apply the throttle.
Note: Keep both feet on the base fairing when unit is in motion.
Release the throttle and apply the brake.
Note: When coming to a complete stop, place both feet on the
ground to balance the unit.
REPAIR AND MAINTENANCE
Turn power “OFF” before conducting any maintenance procedures.
Testing the Brake
To use the brake, squeeze the lever to increase the pressure on the brake. The brake lever is fitted with a cable
adjuster to compensate for cable stretch and/or to fine-tune the lever movement to brake engagement. If brake is not
engaging properly, follow instructions for adjusting the brakes.
Note: The brake lever contains a
safety switch to cut power to the
motor when the brake is applied. In
an emergency, applying the brake
will always stop the product from
moving. Do not disable or replace
this lever with anything other than a
genuine Razor replacement part.
Adjusting the Brake
Tools required: 10 mm wrench
1 To adjust the tension, thread the brake lever adjuster on
the hand brake in or out 1/4 to 1/2 turn until the desired brake
adjustment is attained. Most adjustments are complete at this
step. If brake still needs further adjustment, proceed to step 2.
WARNING: The brake is
capable of skidding the tire and
throwing an unsuspecting rider.
Practice in an open area, free from
obstacles, until you are familiar with
the brake function. Avoid skidding to
a stop as this can cause you to lose
control or damage the rear tire.
2
If brake is too tight or has too much slack,
use a 10 mm wrench to loosen the nut for
additional adjustment on the brake cable on the
rear wheel. Securely tighten nut when done.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
8
REPAIR AND MAINTENANCE
Chain and Rear Wheel Replacement
Tools required: Phillips screwdriver, 10 mm wrench, two (2) 8 mm wrenches, and two (2) 15 mm wrenches.
1 With a Phillips screwdriver,
remove the five (5) screws that
secure the chain guard. Remove
chain guard.
2 With a 10 mm wrench, loosen
3 With two (2) 8 mm wrenches,
the brake cable anchor and
disconnect the cable.
loosen brake housing anchor and
disconnect. Keep the spacer and
washers together.
*Note the hardware sequence (from
outside toward the center).
Left Side (Brake)
15 mm Flange Locknut
Lock Washer
Frame
Washer (Plete Cut)
Brake Plate
4
With two (2) 15 mm wrenches,
loosen the axle. Slide the wheel
forward to loosen the chain and
remove the wheel. *See the
hardware sequence on the right.
Note: Your hands will get greasy
doing this.
Nut
5 Install the new chain or wheel by
6 Verify chain is properly
slipping the chain around the axle.
Slide the axle into the slots on the
frame. Slide the wheel forward and
maneuver the chain onto the rear
sprocket, motor shaft and chain
tensioner.
installed on each sprocket and
tensioner is correctly positioned at
the bottom of the chain.
**Note the hardware sequence
(from left to right).
Cable Guide
Bracket
Frame
Washer
Right Side (Throttle)
15 mm Flange Locknut
Lock Washer
Frame
Washer
Washer
Nut
Washer
Cable Guide Bracket
Brake Plate
Frame
Washer
Bolt
Bolt
Washer
Brake Plate
7 Install the cable guide bracket
to the frame and brake plate
using bolt, washers, and nut.
Do not tighten. **See the
hardware sequence on the right.
8 Thread the brake cable through
9 Reattach the chain guard. Test
the brake adjuster barrel, through
the large spring, and into the small
hole in the side of the anchor bolt.
Position the cable to the original
location (as indicated by the slight
cable kink) and tighten securely.
ride and readjust as needed.
9
REPAIR AND MAINTENANCE
Front Wheel Replacement
Tools required: Phillips screwdriver and 15 mm wrench
1 Remove the nuts on both sides
of the front axle using a 15 mm
wrench then remove the axle safety
washers (note hardware sequence).
2 Insert the wheel into the front
3 Insert the tab on the lock
fork with the lock washers on the
outside of the fork.
washer into the hole on the front
fork and tighten the nuts using two
(2) 15 mm wrenches.
Replacing the Fuse
Tools required: Phillips screwdriver
Turn power switch OFF.
30 Amp
1 Lift up the seat and loosen
the four (4) screws in the storage
compartment and remove the tray.
2 Locate fuse box on top of
WARNING:
To prevent shock, please follow the
instructions accordingly and do not
skip or combine any steps.
3 Remove the fuse and replace
battery. Open the fuse cover to
expose the fuse.
with a new one of equal amperage.
Close the fuse box. Reattach seat/
storage compartment.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
10
REPAIR AND MAINTENANCE
Battery Care and Disposal
Do not store in freezing or below freezing temperatures! To properly maintain your battery and ensure maximum battery
life, carefully read the “Charging the Battery” section on page 7 of this owner’s manual.
Pb
CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED.
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not
dispose of a lead-acid battery in your regular household trash. The incineration, land filling or mixing of sealed lead-acid
batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state
approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is
prohibited by law to throw away lead-acid batteries in the municipal waste stream.
Charger
The charger supplied with the electric product should be regularly examined for damage to the cord, plug, enclosure and
other parts and in the event of such damage, the product must not be charged until it has been repaired or replaced.
Use ONLY with the recommended charger.
Wheels
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect
wheels for excess wear, and adjust and replace drive train components as required.
Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners.
For the complete selection of replacement parts visit shop.razor.com.
Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is listed on the back of this manual.
11
WARNING: If a battery
leak develops, avoid contact with
the leaking acid and place the
damaged battery in a plastic bag.
Refer to the disposal instructions at
left. If acid comes into contact with
skin or eyes, flush with cool water
for at least 15 minutes and contact
a physician.
WARNING: Battery
posts, terminals and related
accessories contain lead and
lead compounds. Wash your
hands after handling.
TROUBLESHOOTING
*Unit(s) should be turned off and fully charged prior to doing any Troubleshooting
NOTE: All troubleshooting steps should be performed by an adult only
Problem
Possible Cause
Solution
Does Not Work Out Of The Box
Loose connection(s)
Check for loose connections/wires
No Longer Works
Blown Fuse
Replace if needed
Loose connection(s)
Check for loose connections/wires
Charger not working
Check power to wall outlet and/or try a different outlet
Check lights on charger:
Plugged into wall = Green
Plugged into wall & unit (Charging) = Red
Charging Complete = Green
No lights - Replace Charger
Battery will not hold a charge
With no weight on the unit, lift up back end and apply the throttle. If motor
engages - Replace Battery
If motor does not engage, but makes a clicking sound - Replace Battery
If motor does not engage, no clicking sound - Replace Control Module
Short Ride Time/Runs Slow
Rider’s weight
Do not exceed 170 lb maximum weight limit
Low tire pressure
Check tires for correct PSI.
Riding conditions
Use only on flat, dry surfaces. Avoid inclines and areas with heavy debris
Battery not fully charged
Charge unit for a full 12 hrs
Old/damaged Battery
With no weight on the unit, lift up back end and apply the throttle. If motor
engages - Replace Battery
Improper battery maintenance
Charge battery at least once a month when not in use
Do not store unit in freezing or below freezing temperatures. Freezing will
permanently damage the battery and greatly reduce ride time
Refer to Page 7 Charging the Battery
Runs Intermittently
Loose connection(s)
Check the wires around the throttle and for other possible loose
connections
Contact your local Razor authorized service center for diagnosis and repair.
Replace - Throttle
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.razor.com or call toll free +1 866 467 2967 to speak to a live Customer Service Representative
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
12
POCKET MOD PARTS
Keep your Pocket Mod running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
01
Handlebar Grip (Right/Left)
10
Front Fork
20
Rear Wheel Complete
02
Single Speed Twist Grip Throttle
11
Front Seat Fairing
(See page 9 for hardware sequence)
Sleeve
12
On/Off Switch
21Chain
03Handlebar
13
Charger Port
22
Chain Guard
04
6 mm Stem Bolt w/Wedge
14
Battery (2-12V/7Ah) w/30 Amp Fuse
23
Chain Tensioner
05
Brake Lever Assembly
15
Seat w/Storage Compartment
24
Rear Seat Fairing w/Name Plate
06
Headset (Upper/Lower)
16
Control Module
25
Rear Fairing w/Trim (Right/Left)
07
Front Fairing w/Head Lamp Cover
17
Base Fairing
08
Front Fairing Cover
18Kickstand
09
Front Wheel Complete
19
02-1
01
05
04
03
Motor (24V 250W)
02
02-1
01
13
12
11
14
15
06
08
07
06
09
24
25
23
10
21
16
17
18
19
22
20
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
13
NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by Razor USA, could void the user’s authority to operate the equipment.
WARRANTY
Razor Limited Warranty
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited Warranty
does not cover normal wear and tear, tire, tube or cables, or any damage,
failure or loss caused by improper assembly, maintenance, storage or use of
the Razor Pocket Mod.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
UNITED STATES
EUROPE
ASIA
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
Razor USA (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
Razor USA (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
+44 (0) 1202 672702
+81 50 7579 6622
info@razor-asia.com
DISTRIBUTED IN THE UK BY:
DISTRIBUTED IN AUSTRALIA BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
Funtastic Limited
Level 2, Tower 2, Chadstone Place
1341 Dandenong Road
Chadstone VIC 3148
Australia
+44 (0) 118 973 6222 Tel
+44 (0) 118 973 6220 Fax
sales@recreationltd.co.uk
+1 800 244 543
Printed in China for Razor USA LLC.
Copyright © 2003-2014 Razor USA, LLC. All rights reserved. Razor® and the Razor logo design
are among the registered trademarks of Razor USA LLC in the United States and/or select
foreign countries. Pocket Mod™ is a trademark of Razor USA LLC.
15
US_140827
Download PDF
Similar pages