FAX System(X) - KYOCERA Document Solutions Singapore

FAX System(X)
OPERATION GUIDE
Safety Conventions in This Guide
This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a
simple troubleshooting action as necessary, so that you can always use the machine in good condition.
Please read the Operation Guide before using the facsimile. Keep it close to the facsimile for easy reference.
The sections of this handbook and parts of the facsimile marked with symbols are safety warnings meant to protect the
user, other individuals and surrounding objects, and ensure correct and safe usage of the facsimile.
WARNING: Indicates that serious injury or even death may result from insufficient
attention to or incorrect compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from
insufficient attention to or incorrect compliance with the related points.
Symbols
The  symbol indicates that the related section includes safety warnings. Specific points of attention are indicated
inside the symbol.
... [General warning]
... [Warning of high temperature]
The
symbol indicates that the related section includes information on prohibited actions. Specifics of the prohibited
action are indicated inside the symbol.
... [Warning of prohibited action]
... [Disassembly prohibited]
The  symbol indicates that the related section includes information on actions which must be performed. Specifics of
the required action are indicated inside the symbol.
... [Alert of required action]
... [Remove the power plug from the outlet]
... [Always connect the machine to an outlet with a ground connection]
Please contact your service representative to order a replacement if the safety warnings in this Operation Guide are
illegible or if the guide itself is missing (fee required).
NOTE
Due to performance updating, information in this Operation Guide is subject to change without notice.
Contents
Contents ....................................................................................................................................i
Safety Information ....................................................................................................................v
About this Operation Guide ............................................................................................v
General Notice ........................................................................................................................ vi
Legal Notice .................................................................................................................. vi
Trademark Information .................................................................................................. vi
Declarations to European Directives ............................................................................. vi
Technical regulations for terminal equipment .............................................................. vii
Network Compatibility Declaration ............................................................................... vii
Introduction ............................................................................................................................ viii
About this Operation Guide ......................................................................................... viii
Conventions in This Guide ............................................................................................ ix
Size and Orientation of Originals and Paper ................................................................. xi
1
Setting up the Machine ........................................................ 1-1
Part Names and Functions ................................................................................................... 1-2
Machine ...................................................................................................................... 1-2
Operation Panel ......................................................................................................... 1-4
Operation Method ...................................................................................................... 1-5
Setting Date and Time .......................................................................................................... 1-6
Local FAX Information Entry ................................................................................................ 1-8
TTI (Transmit Terminal Identification) ........................................................................ 1-8
Local FAX Name ........................................................................................................ 1-8
Local FAX Number ..................................................................................................... 1-9
FAX Dialing Mode .................................................................................................... 1-10
ECM TX .................................................................................................................... 1-11
TX Start Speed ......................................................................................................... 1-11
2
Registering Destinations ..................................................... 2-1
Registering Destinations in the Address Book ..................................................................... 2-2
Adding a contact ........................................................................................................ 2-2
Adding a Group .......................................................................................................... 2-6
Editing and Deleting Address Book Entries ............................................................... 2-9
Printing Address List ................................................................................................ 2-11
Adding a Destination on One Touch Key ........................................................................... 2-12
Adding a Destination ................................................................................................ 2-12
Editing and Deleting One Touch Key ....................................................................... 2-13
3
Sending Faxes ...................................................................... 3-1
Basic transmission procedure .............................................................................................. 3-2
Checking and Editing Destinations ............................................................................ 3-4
Checking the Send Status .......................................................................................... 3-6
Cancelling the Transmission ...................................................................................... 3-7
Using redial ................................................................................................................ 3-8
Methods For Entering the Destination .................................................................................. 3-9
Entering the destination fax number with the numeric keys ....................................... 3-9
Choosing from the Address Book ............................................................................ 3-10
Choosing by One Touch Key ................................................................................... 3-12
Fax transmission functions ................................................................................................. 3-13
Density ............................................................................................................................... 3-14
Original Image .................................................................................................................... 3-14
2-sided Original .................................................................................................................. 3-14
Manual Send ...................................................................................................................... 3-15
Original Size ....................................................................................................................... 3-16
FAX Resolution .................................................................................................................. 3-16
i
File Name Entry .................................................................................................................. 3-16
FAX Direct Transmission .................................................................................................... 3-17
Cancelling Direct Transmission ................................................................................ 3-17
FAX Delayed Transmission ................................................................................................ 3-17
Cancelling Delayed Transmissions .......................................................................... 3-18
FAX TX Report ................................................................................................................... 3-18
Program .............................................................................................................................. 3-19
Registering Program ................................................................................................ 3-19
Confirming the Registered Program ......................................................................... 3-20
Recalling Program .................................................................................................... 3-20
Overwriting Program ................................................................................................ 3-20
Changing the Program Name .................................................................................. 3-21
Deleting Program ..................................................................................................... 3-21
Using Chain Dial ................................................................................................................. 3-23
4
Receiving Faxes ................................................................... 4-1
FAX Automatic Reception .................................................................................................... 4-2
Reception Method ...................................................................................................... 4-2
Flow of reception ........................................................................................................ 4-3
Manual Reception ................................................................................................................ 4-4
Using the Telephone to Receive ................................................................................ 4-4
Fax reception functions ........................................................................................................ 4-6
Fax reception settings .......................................................................................................... 4-6
Duplex Print Output .................................................................................................... 4-6
Reception Date/Time ................................................................................................. 4-6
Media Type for Print Output ....................................................................................... 4-6
5
Using Convenient Fax Functions ......................................... 5-1
Forward Settings .................................................................................................................. 5-2
Setting Forwarding ..................................................................................................... 5-2
Registering Forwarding Destination ........................................................................... 5-3
Forwarding Time Setting ............................................................................................ 5-7
Print Setting ................................................................................................................ 5-8
6
Sending Faxes from PC ........................................................ 6-1
Flow of Sending Faxes from PC ........................................................................................... 6-2
Setup .................................................................................................................................... 6-3
Connection to a PC .................................................................................................... 6-3
Installing the FAX Driver ............................................................................................ 6-3
Uninstalling the FAX Driver ........................................................................................ 6-5
Basic Transmission .............................................................................................................. 6-6
Configuring the Driver Default Settings ...................................................................... 6-8
Default Settings Dialog Box ....................................................................................... 6-9
7
Using a Connected Telephone ............................................. 7-1
FAX/TEL Auto Switch Reception .......................................................................................... 7-2
FAX/Answering Machine Auto Switch Reception ................................................................. 7-4
Manual Send ........................................................................................................................ 7-6
Manual Reception ................................................................................................................ 7-7
Remote Switch Function ...................................................................................................... 7-9
8
1
Checking Communication Status and Machine Information 8Verious Reports for FAX ...................................................................................................... 8-2
Checking FAX Job History ................................................................................................... 8-3
ii
Send Job Log and Print Job Log ................................................................................ 8-3
Outgoing FAX Log and Incoming FAX Log ................................................................ 8-4
Printing Administrative Reports ............................................................................................ 8-5
FAX TX Result Reports .............................................................................................. 8-5
FAX RX Result Reports ............................................................................................. 8-6
Activity Report ...................................................................................................................... 8-7
Printing Activity Reports ............................................................................................. 8-7
Automatic Printout ...................................................................................................... 8-8
Status Page .......................................................................................................................... 8-9
9
Fax Settings ......................................................................... 9-1
Default fax settings ............................................................................................................... 9-2
System Menu Settings ............................................................................................... 9-2
Report ........................................................................................................................ 9-3
Common Settings ....................................................................................................... 9-3
FAX ............................................................................................................................ 9-4
Transmission Restriction ...................................................................................................... 9-8
Registering Permit FAX No. ....................................................................................... 9-9
Changing and Deleting Permit FAX No. ..................................................................... 9-9
Registering Reject FAX No. ..................................................................................... 9-10
Changing and Deleting Reject FAX No. ................................................................... 9-11
Setting Send Restriction ........................................................................................... 9-12
Setting Reception Restriction ................................................................................... 9-13
Unknown Number Reception ................................................................................... 9-13
Unusable Time ................................................................................................................... 9-15
Account Management ........................................................................................................ 9-17
Logging in when Job Accounting has been Enabled ............................................... 9-18
10
Troubleshooting ................................................................. 10-1
Indicators During Sending/Receiving Operation ................................................................ 10-2
Responding to an Attention Indicator Flashes .................................................................... 10-2
Precautions When Turning Power OFF ............................................................................. 10-3
Messages ........................................................................................................................... 10-4
Error Code List ................................................................................................................... 10-5
Troubleshooting .................................................................................................................. 10-7
11
Appendix ............................................................................. 11-1
Character Entry Method ..................................................................................................... 11-2
Using the Keys ......................................................................................................... 11-2
Selecting Type of Characters ................................................................................... 11-3
Characters That Can be Entered Using the Numeric Keys ...................................... 11-3
Entering Symbols ..................................................................................................... 11-4
Entering Characters ................................................................................................. 11-4
Specifications ..................................................................................................................... 11-6
Menu Map .......................................................................................................................... 11-8
Received FAX Sizes and Paper Priority (Metric Model) ................................................... 11-11
Received FAX Sizes and Paper Priority (Inch Model) ...................................................... 11-12
Index ...............................................................................................................................Index-1
iii
iv
Safety Information
About this Operation Guide
This Operation Guide contains information on using the facsimile functions of this machine. Please read the Operation
Guide before you start using the machine.
During use, refer to the Operation Guide for your machine for information regarding the sections listed below.
Environment
Precautions for Use
Loading Paper
Cleaning
Toner Container Replacement
Waste Toner Box Replacement
Solving Malfunctions
Responding to Messages
Clearing Paper Jams
v
General Notice
Legal Notice
WE SHALL HAVE NO LIABILITY FOR LOSS, WHETHER OR PARTIAL, OF RECEIVED DOCUMENTS WHEN SUCH
LOSS IS CAUSED BY DAMAGES TO THE FAX SYSTEM, MALFUNCTIONS, MISUSE, OR EXTERNAL FACTORS
SUCH AS POWER OUTAGES; OR FOR PURELY ECONOMIC LOSSES OR LOST PROFITS RESULTING FROM
MISSED OPPORTUNITIES ATTRIBUTABLE TO MISSED CALLS OR RECORDED MESSAGES RESULTING
THEREFROM.
Trademark Information
•
Microsoft, Windows, Windows XP, Windows Server 2003, Windows Vista, Windows Server 2008/R2, Windows 7,
Windows Server 2012, Windows 8 and Internet Explorer are registered trademarks or trademarks of Microsoft
Corporation in the U.S.A. and/or other countries.
•
Ethernet is a registered trademark of Xerox Corporation.
•
IBM and IBM PC/AT are trademarks of International Business Machines Corporation.
•
Adobe Acrobat, and Flash are registered trademarks of Adobe Systems Incorporated.
All other company and product names in this Operation Guide are trademarks or registered trademarks of their
respective companies. The designations™ and ® are omitted in this guide.
Declarations to European Directives
DECLARATION OF CONFORMITY TO 2004/108/EC, 2006/95/EEC, 93/68/EEC, 1999/5/EC and 2009/125/EC
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the following
specifications.
Limits and methods of measurement for immunity
characteristics of information technology
equipment
EN55024
Limits and methods of measurement for radio
interference characteristics of information
technology equipment
EN55022 Class B
Limits for harmonic currents emissions for
equipment input current 16A per phase
EN61000-3-2
Limitation of voltage fluctuations and flicker in lowvoltage supply systems for equipment with rated
current 16A
EN61000-3-3
Safety of information technology equipment,
including electrical business equipment
EN60950-1
Terminal Equipment (TE);
TBR 21
Attachment requirements for pan-European
approval for connection to the analogue Public
Switched Telephone Networks (PSTNs) of TE
(excluding TE supporting the voice telephony
service) in which network addressing, if provided,
is by means of Dual Tone Multi Frequency (DTMF)
signalling
vi
Technical regulations for terminal equipment
This terminal equipment complies with:
•
TBR21
•
DE 08R00
National AN for D
•
AN 01R00
AN for P
•
DE 09R00
National AN for D
•
AN 02R01
AN for CH and N
•
DE 12R00
National AN for D
•
AN 05R01
AN for D, E, GR, P and N
•
DE 14R00
National AN for D
•
AN 06R00
AN for D, GR and P
•
ES 01R01
National AN for E
•
AN 07R01
AN for D, E, P and N
•
GR 01R00
National AN for GR
•
AN 09R00
AN for D
•
GR 03R00
National AN for GR
•
AN 10R00
AN for D
•
GR 04R00
National AN for GR
•
AN 11R00
AN for P
•
NO 01R00
National AN for N
•
AN 12R00
AN for E
•
NO 02R00
National AN for N
•
AN 16R00
General Advisory Note
•
P 03R00
National AN for P
•
DE 03R00
National AN for D
•
P 04R00
National AN for P
•
DE 04R00
National AN for D
•
P 08R00
National AN for P
•
DE 05R00
National AN for D
Network Compatibility Declaration
The manufacturer declares that the equipment has been designed to operate in the public switched telephone networks
(PSTN) in the following countries:
Austria
France
Liechtenstein
Slovakia
Belgium
Germany
Lithuania
Slovenia
Bulgaria
Greece
Luxembourg
Spain
Cyprus
Hungary
Malta
Sweden
Czech
Iceland
Norway
Switzerland
Denmark
Ireland
Poland
The Netherlands
Estonia
Italy
Portugal
United Kingdom
Finland
Latvia
Romania
vii
Introduction
About this Operation Guide
This Operation Guide contains the following chapters.
Chapter
Contents
1
Setting up the Machine
Explains the part names and the settings required before
using fax.
2
Registering Destinations
Explains the procedures for registering destinations in the
address book and one-touch keys.
3
Sending Faxes
Explains the general methods for sending faxes and
transmission functions.
4
Receiving Faxes
Explains the general methods for receiving faxes and
reception functions.
5
Using Convenient Fax Functions
Explains how to forward the received originals.
6
Sending Faxes from PC
Explains how to send a FAX from a PC.
7
Using a Connected Telephone
Explains convenient functions that use an external
telephone.
8
Checking Communication Status
and Machine Information
Explains how to check the status of recently performed
transmission and reception operations in the message
display. Also explains how to print administrative reports
showing communication results, machine settings, and
registered information.
9
Fax Settings
Explains various settings for controlling fax usage, such as
restricting transmission destinations, blocking fax
reception, and setting prohibited use times.
10
Troubleshooting
Explains what to do when errors are displayed or other
problems occur.
11
Appendix
Explains how to enter characters, and lists the fax
specifications.
viii
Conventions in This Guide
Adobe Reader X is used as an example in the explanations below.
Click an item in the Table of Contents
to jump to the corresponding page.
Click to move from the current page to the previously
displayed page. This is convenient when you want to return to
the page from which you jumped to the current page.
NOTE
Indicates supplemental
explanations and reference
information for operations.
Refer to
Click the underlined text to jump to
the corresponding page.
Indicates that personal injury or
mechanical damage may result
from insufficient attention to or
incorrect compliance with the
related points.
IMPORTANT
Indicates operational
requirements and restrictions to
operate the machine correctly,
and avoid damage to the machine
or property.
NOTE
The items that appear in Adobe Reader vary depending on how it is used. If the Table of Contents or tools do not
appear, refer to Adobe Reader Help.
Certain items are indicated in this guide by the conventions described below.
Convention
[Bold]
[Regular]
"Regular"
Description
Example
Indicates keys on the operation panel and buttons on
your computer screen.
Press the [Start] key.
Indicates a message or setting displayed on the
message display.
[Ready to copy.] appears in the message display.
Indicates a message or setting displayed on the
computer screen.
You can select from the "Print size" menu.
ix
Click [OK].
Press the [▲] or [▼] key to select [On].
Conventions used in operation procedures
Operation panel keys that are pressed are outlined in red.
Procedures consisting of a sequence of operation panel actions or computer operations are numbered as shown below.
1
2
x
Size and Orientation of Originals and Paper
Original sizes and paper sizes such as A4, B5, and Letter can be used in both the horizontal and vertical orientations. To
distinguish the orientations when these sizes are used, "-R" is added to sizes used in the horizontal orientation.
The following icons are used to indicate original and paper placement orientations on the message display.
Orientation
Vertical
Setting Position
(X: Width, Y: Length)
Display
Original
Indicated Size in this
Guide*1
A4, B5, Letter, etc.
Original
Original
Paper
Paper
Paper
Horizontal
Original
A4-R, B5-R, Letter-R, etc.
Original
Original
Paper
Paper
Paper
*1 Original/paper sizes that can be used vary depending on the function and source tray. For details, refer to the appropriate pages
of the function or source tray.
xi
xii
1
Setting up the
Machine
This chapter explains the following topics:
Part Names and Functions ................................................................................................................................ 1-2
Machine ................................................................................................................................................... 1-2
Operation Method .................................................................................................................................... 1-5
Setting Date and Time ....................................................................................................................................... 1-6
Local FAX Information Entry .............................................................................................................................. 1-8
TTI (Transmit Terminal Identification) ...................................................................................................... 1-8
Local FAX Name ...................................................................................................................................... 1-8
Local FAX Number ................................................................................................................................... 1-9
FAX Dialing Mode .................................................................................................................................. 1-10
ECM TX .................................................................................................................................................. 1-11
TX Start Speed ........................................................................................................................................ 1-11
1-1
Setting up the Machine > Part Names and Functions
Part Names and Functions
Machine
This chapter explains the names of parts when the machine is used as a fax machine. For the parts required when
functions other than FAX are used, refer to the machine’s Operation Guide.
1
2
3
4
1
Operation panel
Perform the fax operation with this panel.
2
Power switch
Set this switch to the ON side when performing the fax or copier operation.
3
TEL connector
When using a commercially available telephone set, connect the modular cord to this
connector.
4
LINE connector
Connect the modular cord for the telephone line to this connector.
IMPORTANT
You cannot automatically receive a fax when the power switch is turned off.
1-2
Setting up the Machine > Part Names and Functions
Document Processor (DP)
5
6
7
9
8
5
Top Cover
Open this cover when the original jammed in the Document Processor.
6
Original Width Guides
Adjust these guides according to the original width.
7
Original Table
Stack the sheet originals on this table.
8
Original Eject Table
Read originals are ejected onto this table.
9
Opening Handle
Hold this handle when opening or closing the Document Processor.
1-3
Setting up the Machine > Part Names and Functions
Operation Panel
Displays the density
setting screen.
Displays Status, System
Menu or Counter Menu.
Displays the function menu
for fax.
Displays the original image
setting screen.
Displays the Program
screen.
Displays the duplex setting
screen.
Displays the FAX screen.
Finalizes a function or
menu, and numbers that
have been entered.
Message display.
Displays the setting menu,
machine status, and error
messages.
Processing: Blinks while printing or sending/
receiving.
Increments or decrements
numbers, or selects menu
in the message display. In
addition, moves the cursor
when entering the
characters.
Returns to the previous
display.
Select Key: Selects the menu displayed at the
bottom of the message display.
Memory: Lights when there is a received original
in the FAX memory.
Numeric keys.
Attention: Lights or blinks when an error occurs
and a job is stopped.
Enter numbers and characters.
Recalls the destination registered for One
Touch Keys.
Clears entered numbers and characters.
Press to select No. 17 to No. 32 of One Touch
Keys.
Returns settings to their default states.
Displays the Address Book screen, where you
can add destinations.
Cancels or pauses the job in progress.
Calls the previous destination. Also used to
enter a pause when entering a FAX number.
Confirms the destination or adds a destination.
Starts fax transmission and processing of
settings.
Switches between on-hook and off-hook when
manually sending a FAX.
Puts the machine to sleep or wakes it up.
Returns to the account ID entry screen. (i.e.
logout)
1-4
Setting up the Machine > Part Names and Functions
Operation Method
This section explains how to operate the setting menus on the message display.
Displaying the Menus and Configuring Settings
Press the [Status/System Menu/Counter] key, [Function Menu] key, or function keys to display the setting menus.
Press the [▲] key, [▼] key, [◄] key, [►] key, [OK] key, or [Back] key to select a menu, and perform settings.
Ready to send.
2013/08/08 10:10
Ready to send.
2013/08/08 10:10
200x200
Resltion
200x200
Resltion
Off
Duplex
Normal screen
Setting menus
Status/Sys. Menu:
01 Status
02 Report
03 Counter
Exit
Off
Duplex
Press the [Status/System Menu/Counter]
key, [Function Menu] key, or function keys
to display the setting menus.
The directions of usable arrow keys
are shown on the screen displayed.
When the [▲] or [▼] key is
pressed, the selection moves
line by line.
When the [◄] or [►] key is
pressed, the selection moves in
units of one page.
Status/Sys. Menu:
01 Status
02 Report
03 Counter
Exit
Canceling the menu operation
When [OK] is displayed, press the [OK]
key to confirm the selection.
Status/Sys. Menu:
04 System
05 Admin/Accounting
06 Common Settings
Exit
Press the [OK] key to display
the selected menu.
The selected item is displayed with [*]
(asterisk) at the beginning.
Common Settings:
01 Language
02 Default Screen
03 Sound
Exit
Language:
01 *English
02 Deutsch
03 Francais
When [Exit] is displayed, press [Exit] to exit
the setting menu and return to the normal
screen.
When other function keys are pressed, the
menu operation is canceled and the screen
of the corresponding function appears.
When the [▲] or [▼] key is pressed,
the selection moves line by line.
Language:
01 *English
02 Deutsch
03 Francais
Press the [Back] key to return to
the screen one level higher.
1-5
Press the [OK] key to confirm
the selected setting.
Setting up the Machine > Setting Date and Time
Setting Date and Time
Set the local date and time at the place of installation.
When you send a fax using the transmission function, the date and time as set here will be printed in the header of the
fax. Set the date, time and time difference from GMT of the region where the machine is used.
NOTE
Be sure to set the time difference before setting the date and time.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Common Settings].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Date Settings].
5 Press the [OK] key.
NOTE
If the login user name entry screen appears during operations, log in by referring to the
machine's Operation Guide for Administrator User Name and Password.
The factory default login user name and login password are set as shown below.
Login User Name
Login Password
Admin*1
Admin*1
*1 Upper case and lower case letters are distinguished (case sensitive).
2
Set the time difference.
1 Press the [▲] or [▼] key to select [Time Zone].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to set the time zone.
4 Press the [OK] key.
3
Set the date and time.
1 Press the [▲] or [▼] key to select [Date/Time].
2 Press the [OK] key.
1-6
Setting up the Machine > Setting Date and Time
3 Press the [▲] or [▼] key to set the year, month, and day. Press the [◄] and [►] key to
move the cursor right and left.
Date/Time:
Year Month
Day
2013
01
01
( Time Zone:Pfic Time )
4 Press the [OK] key.
5 Press the [▲] or [▼] key to set the hour, minute, and second. Press the [◄] and [►] key to
move the cursor right and left.
Date/Time:
Hour
Min. Second
10 :
10:
50
(Time Zone:Pfic Time )
6 Press the [OK] key.
4
Set the Date Format.
1 Press the [▲] or [▼] key to select [Date Format].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select the display format of year, month, and date.
Date Format:
01 *Month/Day/Year
02 Day/Month/Year
03 Year/Month/Day
NOTE
The following date formats are available.
•
[Month/Day/Year]
•
[Day/Month/Year]
•
[Year/Month/Day]
4 Press the [OK] key.
5
Set the Summer Time.
NOTE
Summer Time can be set according to the region set in Time Zone.
1 Press the [▲] or [▼] key to select [Summer Time].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [On] or [Off].
4 Press the [OK] key.
1-7
Setting up the Machine > Local FAX Information Entry
Local FAX Information Entry
Register the local FAX information below.
TTI (Transmit Terminal Identification)
Select whether or not to print the local fax information on the fax on the receiving system.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Transmission].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [TTI].
7 Press the [OK] key.
2
Set the TTI.
1 Press the [▲] or [▼] key to select [On] or [Off].
NOTE
To have your fax number printed on the fax by the receiving machine, set [TTI] to [On].
2 Press the [OK] key.
Local FAX Name
Register the local fax name printed on the fax on the receiving system.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Transmission].
1-8
Setting up the Machine > Local FAX Information Entry
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Local FAX Name].
7 Press the [OK] key.
2
Set the Local FAX Name
1 Use the numeric keys to enter the local fax name.
Local FAX Name:
Sales department
Common Settings
ABC
Text
NOTE
Refer to Character Entry Method on page 11-2 for details on entering characters.
2 Press the [OK] key.
Local FAX Number
Enter the local fax number to be printed on the fax on the receiving system.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Transmission].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Local FAX Number].
7 Press the [OK] key.
1-9
Setting up the Machine > Local FAX Information Entry
2
Local FAX Number Entry
1 Use the numeric keys to enter the local fax number.
Local FAX Number:
0123456789
NOTE
Up to 20 digits can be entered as the local fax number.
Press the [*/.] keys on numeric keys to enter "+".
2 Press the [OK] key.
FAX Dialing Mode
Select the dialing mode according to the line type.
NOTE
This setting does not appear in some regions.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Transmission].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [FAX Dialing Mode].
7 Press the [OK] key.
2
Set the FAX Dialing Mode.
1 Press [▲] or [▼] to select [Tone(DTMF)] or [Pulse(10pps)].
FAX Dialing Mode:
01 *Tone(DTMF)
02 Pulse(10pps)
2 Press the [OK] key.
1-10
Setting up the Machine > Local FAX Information Entry
ECM TX
Set whether ECM TX is performed. ECM is a communication mode specified by the ITU-T (International
Telecommunication Union) that retransmits data when an error occurs. Fax machines that have ECM mode check for
errors as they communicate, preventing distortion of the image due to noise on the line and other conditions.
NOTE
When there is a large amount of noise on the line, communication may take slightly longer
than when [Off] is selected.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Transmission].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [ECM TX].
7 Press the [OK] key.
2
Configure the settings.
1 Press [▲] or [▼] to select [On] or [Off].
2 Press the [OK] key.
TX Start Speed
Set the TX Start Speed. When communication conditions are bad, the fax may not be transmitted correctly. In that case,
set a lower TX Start Speed.
NOTE
Normally this should be used with the default setting.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Transmission].
1-11
Setting up the Machine > Local FAX Information Entry
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [TX Start Speed].
7 Press the [OK] key.
2
Configure the settings.
1 Press [▲] or [▼] to select [9600bps], [14400bps] or [33600bps].
TX Start Speed:
01 9600bps
02 14400bps
03 *33600bps
2 Press the [OK] key.
1-12
2
Registering
Destinations
This chapter explains the following topics:
Registering Destinations in the Address Book ................................................................................................... 2-2
Adding a contact ...................................................................................................................................... 2-2
Adding a Group ........................................................................................................................................ 2-6
Editing and Deleting Address Book Entries ............................................................................................. 2-9
Printing Address List ............................................................................................................................... 2-11
Adding a Destination on One Touch Key ......................................................................................................... 2-12
Adding a Destination .............................................................................................................................. 2-12
Editing and Deleting One Touch Key ..................................................................................................... 2-13
2-1
Registering Destinations > Registering Destinations in the Address Book
Registering Destinations in the Address Book
Add a new destination to the Address Book. There are two registering methods, contacts and groups. When adding a
group, enter the group name and select group members from the Address Book.
Adding a contact
A maximum of 100 contact addresses can be registered. Contact name, fax number, transmission start speed, and ECM
can be registered for each destination.
NOTE
Contact addresses can also be registered in the system menu.
Contact addresses can also be registered with Command Center RX. For details, refer to the machine’s Operation
Guide.
1
Display the screen.
1 Press the [FAX] key.
2 Press the [Address Book] key.
2
Adds a new destination.
1 Press [Menu].
Address Book:
Sales Department 1
Sales Group
Support Department
Menu
2 Press the [▲] or [▼] key to select [Add Address].
Menu:
04 Add Address
05 Edit Addressbook
06 Delete
3 Press the [OK] key.
3
Select the registration method.
1 Press the [▲] or [▼] key to select [Contact].
2 Press the [OK] key.
2-2
Registering Destinations > Registering Destinations in the Address Book
4
Enter the contact name.
1 Press the [] or [] key to select [Contact Name].
Detail:
Contact Name
1/ 3
Edit
2 Press [Edit].
3 Enter the destination name.
Contact Name:
Sales department
Common Settings
ABC
Text
Up to 32 characters can be entered.
For details on character entry, refer to Character Entry Method on page 11-2.
4 Press the [OK] key.
5
Enter the fax number.
1 Press the [] or [] key to select [FAX Number].
Detail:
FAX Number:
0123456789
2/ 3
Edit
2 Press [Edit].
3 Enter the fax number.
FAX No. Entry:
0123456789
Detail
Enter the fax number of the receiving system using the numeric keys.
Up to 32 digits can be entered as the fax number of the receiving system.
Pressing the [Address Recall/Pause] key adds about three seconds of waiting time during
dialing. For example, when dialing the receiving system on an external line, you can use this
method to insert a pause before resuming dialing after you dial a specific number.
6
Select transmission settings.
1 Press [Detail].
2 Press the [] or [] key to select [TX Start Speed].
2-3
Registering Destinations > Registering Destinations in the Address Book
FAX Detail:
TX Start Speed:
33600bps
1/ 2
Change
3 Press [Change].
4 Press [▲] or [▼] to select [9600bps], [14400bps] or [33600bps].
NOTE
Normally the default setting should be used.
5 Press the [OK] key.
6 Press the [] or [] key to select [ECM].
FAX Detail:
ECM:
On
2/ 2
Change
7 Press [Change].
8 Press [▲] or [▼] to select [On] or [Off].
ECM is a communication mode specified by the ITU-T (International Telecommunication
Union) that retransmits data when an error occurs. Fax machines that have ECM mode check
for errors as they communicate, preventing distortion of the image due to noise on the line and
other conditions.
9 Press the [OK] key.
10Press the [OK] key.
7
Enter the address number.
1 Press the [] or [] key to select [Address Number].
Detail:
Address Number:
053
3/ 3
Edit
2 Press [Edit].
3 Enter the address number.
Address Number:
(001 - 120)
053
Press the [▲], [▼] key or numeric keys to enter a particular Address Number (001-120).
Address Number is an ID for a destination.
2-4
Registering Destinations > Registering Destinations in the Address Book
4 Press the [OK] key.
8
Register the destination.
1 Press the [OK] key.
Detail:
Address Number:
053
3/ 3
Edit
[Completed.] is displayed and the destination is registered.
2-5
Registering Destinations > Registering Destinations in the Address Book
Adding a Group
Compile two or more contacts into a group. Designations in the group can be added at the same time. When adding a
group, a maximum of 20 groups can be added in the Address Book.
Before adding a group in the Address Book, the contacts to be included in the group must be added first.
NOTE
Designations in the group can also be registered in the system menu.
Contact addresses can also be registered with Command Center RX. For details, refer to the machine’s Operation
Guide.
1
Display the screen.
1 Press the [FAX] key.
2 Press the [Address Book] key.
2
Adds a new destination.
1 Press [Menu].
Address Book:
Sales Department 1
Sales Group
Support Department
Menu
2 Press the [▲] or [▼] key to select [Add Address].
Menu:
04 Add Address
05 Edit Addressbook
06 Delete
3 Press the [OK] key.
3
Select the registration method.
1 Press the [▲] or [▼] key to select [Group].
2 Press the [OK] key.
2-6
Registering Destinations > Registering Destinations in the Address Book
4
Enter the group name.
1 Press the [] or [] key to select [Group Name].
Detail:
Group Name:
1/ 3
Edit
2 Press [Edit].
3 Enter the group name.
Group Name:
Sales Group
Common Settings
ABC
Text
Up to 32 characters can be entered.
For details on character entry, refer to Character Entry Method on page 11-2.
4 Press the [OK] key.
5
Select the members (destinations).
1 Press the [] or [] key to select [Group Member].
Detail:
Group Member:
02
2/ 3
Edit
2 Press [Edit].
3 Press [Menu].
Group Member:
Sales Department 1
Sales Department 2
Menu
4 Press the [▲] or [▼] key to select [Add Member].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select the member you want to add.
Contacts:
Sales Department 1
Sales Department 2
Sales Department 3
Menu
2-7
Registering Destinations > Registering Destinations in the Address Book
7 Press the [OK] key.
The selected member is added to Group Member.
Members can be added by repeating steps 3 to 7.
6
Delete the members.
1 Press the [▲] or [▼] key to select the member you want to delete.
Group Member:
Sales Department 1
Sales Department 2
Sales Department 3
Menu
2 Press [Menu].
3 Press the [▲] or [▼] key to select [Delete].
4 Press the [OK] key.
5 Press [Yes] in confirmation screen.
The selected member is deleted from Group Member.
7
Confirm the registered member.
1 Press the [Back] key when all members are registered.
Group Member:
Sales Department 1
Sales Department 2
Sales Department 3
Menu
8
Enter the address number.
1 Press the [] or [] key to select [Address Number].
Detail:
Address Number:
053
3/ 3
Edit
2 Press [Edit].
3 Enter the address number.
Address Number:
(001 - 120)
053
Press the [▲], [▼] key or numeric keys to enter a particular Address Number (001-120).
Address Number is an ID for a destination.
2-8
Registering Destinations > Registering Destinations in the Address Book
9
Register the group.
1 Press the [OK] key.
Detail:
Address Number:
053
3/ 3
Edit
[Completed.] is displayed and the group is registered.
Editing and Deleting Address Book Entries
Edit and delete the destinations (contacts) you added to the Address Book.
1
Display the screen.
1 Press the [FAX] key.
2 Press the [Address Book] key.
3 Press [Menu].
Address Book:
Sales Department 1
Sales Group
Support Department
Menu
4 Press the [▲] or [▼] key to select [Edit Addressbook].
Menu:
04 Add Address
05 Edit Addressbook
06 Delete
5 Press the [OK] key.
2
Edit or delete the destination.
To edit the destination
2-9
Registering Destinations > Registering Destinations in the Address Book
1 Press the [▲] or [▼] key to select the destination (contacts) or group to edit.
Edit Addressbook
Sales Department 1
Sales Group
Support Department
Menu
2 Press the [OK] key.
3 Press the [] or [] key to select the item to change.
Detail:
Contact Name
1/ 3
Edit
4 Press [Edit].
Refer to Adding a contact on page 2-2 or Adding a Group on page 2-6 for how to change.
To delete a member (group)
1 Press the [▲] or [▼] key to select the group to edit.
Edit Addressbook
ABCDEF
GHIJKL
MNOPQR
Menu
2 Press the [OK] key.
3 Press the [] or [] key to select [Group Member].
Detail:
Group Member:
02
2/ 3
Edit
4 Press [Edit].
5 Press the [▲] or [▼] key to select the member you want to delete.
Group Member:
Sales Department 1
Sales Department 2
Sales Department 3
Menu
6 Press [Menu].
7 Press the [▲] or [▼] key to select [Delete].
8 Press the [OK] key.
9 Press [Yes] in confirmation screen.
2-10
Registering Destinations > Registering Destinations in the Address Book
To delete a destination(contacts) or group
1 Press the [▲] or [▼] key to select the destination (contacts) or group to delete.
Edit Addressbook
Sales Department 1
Sales Group
Support Department
Menu
2 Press [Menu].
3 Press the [▲] or [▼] key to select [Delete].
4 Press the [OK] key.
5 Press [Yes] in confirmation screen.
Printing Address List
You can print the list of destinations registered in the Address Book.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Edit Destination].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Print List].
5 Press the [OK] key.
2
Print
1 Press the [▲] or [▼] key to select [FAX List (No.)].
2 Press the [OK] key.
3 Press [Yes] in confirmation screen. The list is printed.
2-11
Registering Destinations > Adding a Destination on One Touch Key
Adding a Destination on One Touch Key
Add a new destination (contact or group) on One Touch Key.
Adding a Destination
Add a new destination (contact or group). A maximum of 32 destinations can be registered.
To register a destination to a One Touch Key, it must first be registered in the Address Book. Register one or more
destinations as needed before proceeding.
NOTE
Numbers 1 to 16 are the One Touch Key numbers while the [Shift Lock] indicator is switched off. Numbers 17 to 32
are the One Touch Key numbers while the [Shift Lock] indicator is switched on by pressing the [Shift Lock] key.
1
Select the One Touch Key to be registered.
1 Press the One Touch Key that you want to register and hold it (2 seconds or more).
2 Press the [▲] or [▼] key to select a key number.
Select Key No.
01 No. 1
02 No. 17
Exit
3 Press the [OK] key.
When a unregistered One Touch Key number is selected, the Address Book appears. Go to
the next step.
When the registered One Touch Key number is selected, the Key Edit screen appears. Select
another key number or edit or delete the One Touch Key.
Refer to Editing and Deleting One Touch Key on page 2-13 for edition and deletion of the One
Touch Key.
2
Select the destinations.
1 Press the [▲] or [▼] key to select the destination (contact or group) you want to register to
the One touch key from the Address Book.
Address Book:
Sales Department 1
Sales Group
Support Department
Menu
2 Press the [OK] key.
[Completed.] is displayed and One Touch Key is registered.
2-12
Registering Destinations > Adding a Destination on One Touch Key
Editing and Deleting One Touch Key
Edit and delete the destinations you added to One Touch Key.
1
Select the One Touch Key to be edited or deleted.
1 Press the One Touch Key to be edited or deleted (2 seconds or more).
2 Press the [▲] or [▼] key to select a key number.
Select Key No.
01 No. 1
02 No. 17
Exit
3 Press the [OK] key.
When a registered One Touch Key number is selected, the Key Edit screen appears. Go to the
next step.
When an unregistered One Touch Key number is selected, the Address Book appears. The
One Touch Key can be registered by selecting the destination from the Address Book.
Refer to Adding a Destination on page 2-12 for registration of the One Touch Key.
2
Edit or delete the destination.
When checking the registered destination
1 Press the [▲] or [▼] key to select [Detail].
2 Press the [OK] key. The destination name is displayed.
3 Press the [OK] key.
When changing the destination to another destination
1 Press the [▲] or [▼] key to select [Edit].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select the new destination.
4 Press the [OK] key.
[Completed.] is displayed and the destination is changed.
When deleting registration contents
1 Press the [▲] or [▼] key to select [Delete].
2 Press the [OK] key.
3 Press [Yes] in confirmation screen.
[Completed.] is displayed and One Touch Key becomes unregistered.
2-13
3
Sending Faxes
This chapter explains the following topics:
Basic transmission procedure ............................................................................................................................ 3-2
Checking and Editing Destinations ..........................................................................................................
Checking the Send Status .......................................................................................................................
Cancelling the Transmission ....................................................................................................................
Using redial ..............................................................................................................................................
3-4
3-6
3-7
3-8
Methods For Entering the Destination ............................................................................................................... 3-9
Entering the destination fax number with the numeric keys .................................................................... 3-9
Choosing from the Address Book .......................................................................................................... 3-10
Choosing by One Touch Key ................................................................................................................. 3-12
Fax transmission functions .............................................................................................................................. 3-13
Density ............................................................................................................................................................. 3-14
Original Image .................................................................................................................................................. 3-14
2-sided Original ................................................................................................................................................ 3-14
Manual Send .................................................................................................................................................... 3-15
Original Size ..................................................................................................................................................... 3-16
FAX Resolution ................................................................................................................................................ 3-16
File Name Entry ............................................................................................................................................... 3-16
FAX Direct Transmission .................................................................................................................................. 3-17
Cancelling Direct Transmission ............................................................................................................. 3-17
FAX Delayed Transmission .............................................................................................................................. 3-17
Cancelling Delayed Transmissions ........................................................................................................ 3-18
FAX TX Report ................................................................................................................................................. 3-18
Program ........................................................................................................................................................... 3-19
Registering Program .............................................................................................................................. 3-19
Recalling Program ................................................................................................................................. 3-20
Changing the Program Name ................................................................................................................ 3-21
Using Chain Dial .............................................................................................................................................. 3-23
3-1
Sending Faxes > Basic transmission procedure
Basic transmission procedure
The basic procedure for using the fax system is explained below.
1
Press the [FAX] key.
Ready to send.
2013/08/08 10:10
200x200
Resltion
Off
Duplex
The base screen for fax appears.
2
Place the originals.
Refer to the machine’s Operation Guide for placing originals.
3
Select the transmission method.
There are two transmission methods: memory transmission and direct transmission.
Memory transmission: The original is scanned into memory before communication starts.
Memory transmission is selected by default.
Direct transmission: The destination is dialed and communication starts before the original is
scanned.
For details, refer to FAX Direct Transmission on page 3-17.
4
Specifying destination.
FAX No. Entry:
0123456789
Chain
Detail
Enter the fax number of the receiving system using the numeric keys.
For the procedure for selecting a destination in the address book, refer to Choosing from the
Address Book on page 3-10.
For the procedure for selecting the destination using the One Touch Key, refer to Choosing by One
Touch Key on page 3-12.
NOTE
Up to 64 digits can be entered as the fax number of the receiving system.
Pressing the [Address Recall/Pause] key adds about three seconds of waiting time during
dialing. For example, when dialing the receiving system on an external line, you can use this
method to insert a pause before resuming dialing after you dial a specific number.
3-2
Sending Faxes > Basic transmission procedure
5
Selecting the functions.
The following functions can be set for FAX transmission.
6
•
Density  page 3-14
•
Original Image  page 3-14
•
2-sided Original  page 3-14
•
Original Size  page 3-16
•
FAX Resolution  page 3-16
•
File Name Entry  page 3-16
•
FAX Delayed Transmission  page 3-17
•
FAX TX Report  page 3-18
•
Program  page 3-19
Send Start.
Press the [Start] key.
When scanning finishes, transmission starts.
When originals are placed in the document processor
After originals placed in the document processor are scanned and stored in the memory, the
receiving system is dialed.
When originals are placed on the glass surface
After originals placed on the glass surface are scanned and stored in the memory, the
receiving system is dialed.
NOTE
When continuous scan is set, you can continue with scanning of a next original after an
original on the glass surface has been stored in memory. Every time one page is scanned,
you perform an operation to allow continued scanning, and after all the originals have been
stored in memory, the receiving system is dialed.
3-3
Sending Faxes > Basic transmission procedure
Checking and Editing Destinations
Check and edit a selected destination.
1
Press the [FAX] key.
2
Press the [Confirm/Add Destination] key.
3
Check the destination.
1 Press the [▲] or [▼] key to select the destination you want to check.
Dest. Confirm.:
0123456789
Sales Group
9876543210
Exit
Add
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Detail/Edit].
4 Press the [OK] key.
Information of the destination is displayed.
5 Press the [OK] key when checking of the destination is complete.
4
Change the FAX number.
NOTE
This step is required only when the FAX number is entered using the numeric keys.
1 Press the [▲] or [▼] key to select the destination that you want to change the FAX number
for.
Dest. Confirm.:
0123456789
Sales Group
9876543210
Exit
Add
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Detail/Edit].
4 Press the [OK] key.
5 Reenter the FAX number using the numeric keys.
3-4
Sending Faxes > Basic transmission procedure
NOTE
When deleting characters, press the [Clear] key.
6 Press the [OK] key.
5
Add the destination (when entering the FAX number using the numeric
keys).
1 Press [Add].
Dest. Confirm.:
0123456789
Sales Group
9876543210
Exit
Add
2 Enter the fax number of the receiving system using the numeric keys.
NOTE
For the procedure for entering the FAX number using the numeric keys, refer to Entering the
destination fax number with the numeric keys on page 3-9.
3 Press the [OK] key.
6
Delete the destination.
1 Press the [▲] or [▼] key to select the destination you want to delete.
Dest. Confirm.:
0123456789
Sales Group
9876543210
Exit
Add
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Delete].
4 Press the [OK] key.
5 Press [Yes] in confirmation screen.
[Completed.] is displayed and the destination is removed.
7
Exit the operation.
1 Press [Exit].
Dest. Confirm.:
0123456789
Sales Group
9876543210
Exit
Add
3-5
Sending Faxes > Basic transmission procedure
Checking the Send Status
1
Press the [Status/System Menu/Counter] key.
2
Display the send job status screen.
1 Press the [▲] or [▼] key to select [Status].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Send Job Status].
4 Press the [OK] key.
Display the send job status screen.
3
Check the details of the transmission job.
1 Press the [▲] or [▼] key to select the job you want to check.
Send Job Status:
0010
0123456789
0011
1234567890 ...
0012
2345678901 ...
Menu
Cancel
2 Press [Menu].
3 Press the [▲] or [▼] key to select [Detail].
4 Press the [OK] key.
5 Press the [] or [] key to check the details of the job.
0010 Detail:
Status:
Processing
1/7
6 Press the [OK] key when checking of the job is complete.
3-6
Sending Faxes > Basic transmission procedure
Cancelling the Transmission
The method for cancelling communication with this machine differs depending on the transmission method (memory
transmission or direct transmission) and communication form. Methods of cancelling in various cases are explained
here.
Cancelling Memory Transmission (while originals are being scanned)
1
Press the [Stop] key.
During memory transmission, to cancel scanning while originals are being scanned, press the
[Stop] key on the operation panel.
Scanning of originals is canceled, and the originals are ejected. When originals remain in the
document processor, take them out from the original eject table.
Cancelling Memory Transmission (during communication)
NOTE
Even if transmission is canceled, there is a possibility that pages scanned prior to cancelation were sent to the
receiving party. Check with the receiving party to see if pages were accidentally sent.
1
Press the [Stop] key.
2
Display the send job list screen.
1 Press the [▲] or [▼] key to select [Send Job List].
2 Press the [OK] key.
Display the send job list screen.
3
Canceling Transmission.
1 Press the [▲] or [▼] key to select the job to cancel.
Send Job List:
0008
0123456789
0009
1234567890
0010
2345678901
Resume
Menu
2 Press [Menu].
3 Press the [▲] or [▼] key to select [Cancel Job].
4 Press the [OK] key.
5 Press [Yes] in the confirmation screen. The selected job is deleted.
3-7
Sending Faxes > Basic transmission procedure
Using redial
Redial is a function allowing you to dial the last entered number once again.
Use this when the receiving system does not respond when you have tried to send a fax. When you want to send the fax
to the same receiving system, press the [Address Recall/Pause] key, and you can call the receiving system you dialed
on the destination list.
1
Press the [FAX] key.
2
Press the [Address Recall/Pause] key.
3
Press the [Start] key.
The previously dialed destination is called.
The transmission will start.
NOTE
Recall information is canceled in the following conditions.
•
When you turn the power off
•
When you send a next fax (new recall information is registered)
•
When you log out
3-8
Sending Faxes > Methods For Entering the Destination
Methods For Entering the Destination
Entering the destination fax number with the numeric keys
The procedure for entering the destination fax number with the numeric keys is explained below.
1
Press the [FAX] key.
2
Enter the fax number of the receiving system using the numeric keys.
FAX No. Entry:
0123456789
Chain
Detail
Up to 64 digits can be entered as the fax number of the receiving system.
Pressing the [Address Recall/Pause] key adds about three seconds of waiting time during
dialing. For example, when dialing the receiving system on an external line, you can use this
method to insert a pause before resuming dialing after you dial a specific number.
NOTE
You can change the settings of TX Start Speed and ECM by pressing [Details]. Refer to
Changing the Settings of TX Start Speed and ECM on page 3-9.
3
Press the [OK] key.
NOTE
To send to multiple destinations, enter the next fax number and press the [OK] key. You can
send to as many as 100 destinations at once.
Changing the Settings of TX Start Speed and ECM
Follow the steps below to change TX Start Speed and ECM settings.
1 Press [Details] after entering the FAX number of the destination.
FAX No. Entry:
0123456789
Chain
Detail
3-9
Sending Faxes > Methods For Entering the Destination
2 Press the [] or [] key to select [TX Start Speed].
FAX Detail:
TX Start Speed:
33600bps
1/ 2
Change
3 Press [Change].
4 Press [▲] or [▼] to select [9600bps], [14400bps] or [33600bps].
NOTE
Normally the default setting should be used.
5 Press the [OK] key.
6 Press the [] or [] key to select [ECM].
FAX Detail:
ECM:
On
2/ 2
Change
7 Press [Change].
8 Press [▲] or [▼] to select [On] or [Off].
ECM is a communication mode specified by the ITU-T (International Telecommunication
Union) that retransmits data when an error occurs. Fax machines that have ECM mode check
for errors as they communicate, preventing distortion of the image due to noise on the line and
other conditions.
9 Press the [OK] key.
10Press the [OK] key.
Choosing from the Address Book
Select a destination registered in the Address Book.
NOTE
For more information about how to register destinations in the Address Book, refer to Registering Destinations in the
Address Book on page 2-2.
1
Press the [FAX] key.
2
Press the [Address Book] key.
3-10
Sending Faxes > Methods For Entering the Destination
3
Press the [▲] or [▼] key to select the destination.
Address Book:
Sales Department 1
Sales Group
Support Department
Menu
NOTE
When checking information of the destination, press [Menu], select [Details], and then press
the [OK] key.
Destination Search
The destination can be searched by name.
1 Press [Menu].
2 Press the [▲] or [▼] key to select [Search (Name)].
3 Press the [OK] key.
4 Enter characters to search using the numeric keys.
For details on character entry, refer to Character Entry Method on page 11-2.
Search(Name)
AB
Common Settings
ABC
Text
5 Press the [OK] key. The searched destination is displayed.
4
Press the [OK] key.
To send to multiple destinations, repeat steps 2 to 4. You can send to as many as 100
destinations at once.
NOTE
To check or change a selected destination, refer to Checking and Editing Destinations on
page 3-4.
3-11
Sending Faxes > Methods For Entering the Destination
Choosing by One Touch Key
Select the destination using the One Touch Keys.
NOTE
For more information on adding One Touch keys, refer to Adding a Destination on One Touch Key on page 2-12.
1
Press the [FAX] key.
2
Press the One touch key where the destination is registered.
When selecting One Touch Key numbers 17 to 32, the One touch Key needs to be pressed
after switching on the [Shift Lock] indicator by pressing the [Shift Lock] key.
3-12
Sending Faxes > Fax transmission functions
Fax transmission functions
To configure the settings for functions, press the key of the function you want to configure. You can also press the
[Function Menu] key to select from other functions displayed on the message display.
Operation Method (page 1-5)
1
Selects the item displayed or changes the
numeric value.
Cancels the current menu setting to
return to the menu one level higher.
2
Confirms the selected setting.
For details on each function, see the table below.
Key
Function
Description
Reference
page
Density
Adjust density.
page 3-14
Original Image
Select original image type.
page 3-14
2-sided Original *1
Automatically scan 2-sided originals.
page 3-14
Manual Send
This method allows you to send originals by pressing
the [Start] key after confirming that the telephone line
has connected to the receiving system.
page 3-15
*1 The optional document processor is required.
Key
Function
Description
Reference
page
Original Size
Specify the original size to be scanned.
page 3-16
FAX Resolution
Set the resolution at which to scan originals.
page 3-16
File Name Entry
Adds a file name.
page 3-16
FAX Direct TX
Connect to the destination first and then scan the
original.
page 3-17
FAX Delayed TX
Specify a time for transmission.
page 3-17
FAX TX Report
Print transmission results after transmission.
page 3-18
NOTE
For the procedure for transmitting FAX, refer to Basic transmission procedure on page 3-2.
3-13
Sending Faxes > Density
Density
Adjust density. Press the [▲] or [▼] key to select [Darker +3] to [Lighter -3].
NOTE
When you want to increase the density of the original that has thin density, density needs to be adjusted to Darker.
When you want to reduce the density of the original that has thick density, density needs to be adjusted to Lighter.
Original Image
Select original image type.
Item
Description
Text+Photo
Best for mixed text and photo documents.
Photo
Best for photos taken with a camera.
Text
Sharply renders pencil text and fine lines.
2-sided Original
Select the type and orientation of the binding based on the original.
NOTE
The optional document processor is required.
Item
Description
1-sided
Set when using a 1-sided sheet original.
2-sided
Set when using a 2-sided sheet original that will be bound on the left or
right.
Detail
Original
Binding
Left/Right
Set when using a 2-sided sheet original that will be bound on the left or
right.
Top
Set when using a 2-sided sheet original that will be bound at the top.
Original Orientation
To ensure that the originals are sent in the correct orientation for reading,
indicate which end of the original is the top. When the original is a twosided or facing pages original, the orientation of the original must be set.
3-14
Sending Faxes > Manual Send
Manual Send
This method allows you to send originals by pressing the [Start] key after confirming that the telephone line has
connected to the receiving system.
NOTE
Connecting a telephone set (commercially available product) to this machine enables you to talk with the person at the
receiving system before sending originals.
1
Press the [FAX] key.
2
Place the originals.
3
Press the [On hook] key.
4
Dial the destination.
On Hook:
0123456789
ManualRX
Use the numeric keys to enter the number of the receiving system.
5
Press the [Start] key.
When you hear the fax tone, the telephone line has connected to the receiving system. Press
the [Start] key. Transmission begins.
3-15
Sending Faxes > Original Size
Original Size
Specify the original size to be scanned.
Item
Description
Auto
Have the size of original detected
automatically.
A3, A4-R, A4, A5-R, A5, A6-R, B4, B5-R, B5, B6-R, B6, Folio, 216 × 340 mm, Ledger,
Letter-R, Letter, Legal, Statement-R, Statement, 11 × 15", Oficio II, 8K, 16K-R, 16K,
Hagaki, Oufukuhagaki, Custom*1
Select from standard sizes.
*1 For instructions on how to specify the custom original size, refer to the machine’s Operation Guide.
NOTE
Be sure to always specify the original size when using custom size originals.
FAX Resolution
Select fineness of images when sending FAX. The larger the number, the better the image resolution. However, better
resolution also means larger file sizes and longer send times.
Item
Description
200x100dpi Norm.(Normal)
when sending originals with standard size
characters
Typical character size: 10.5 point
(example: Resolution Resolution)
200x200dpi Fine(Fine)
when sending originals
with relatively small characters and thin lines
Typical character size: 8 point
(example: Resolution Resolution)
200x400dpi S.Fin(Super Fine)
when sending originals with minute characters and
lines
Typical character size: 6 point
(example: Resolution Resolution)
NOTE
The default setting is [200x100dpi Norm.]. The higher the resolution, the clearer the image, but the fax transmission
time is longer.
File Name Entry
Adds a file name. Additional information such as job number and date can also be set. You can check a job history or job
status using the file name, date, or job number specified here.
Enter the file name (up to 32 characters), and press the [OK] key.
To specify a date or job number, select [Additional Info.] and press the [OK] key.
Character Entry Method (page 11-2)
3-16
Sending Faxes > FAX Direct Transmission
FAX Direct Transmission
You can directly transmit originals without scanning them into the memory. Scanning of the originals starts after the
connection is made with the receiving system, allowing you to verify that each page of the fax has been properly sent.
Setting for Direct
transmission
Description
On
Starts direct transmission.
Dials the receiving system, and after the communication has started, originals are scanned.
Off
Starts memory transmission.
After originals are scanned into memory, the communication starts.
NOTE
In direct transmission, you can designate only one destination for one transmission.
For the procedure for transmitting FAX, refer to Basic transmission procedure on page 3-2. The destination is dialed
and communication starts before the original is scanned.
Cancelling Direct Transmission
During direct transmission, to cancel communication during transmission, press the [Stop] key. The originals that have
been scanned are ejected, and the screen returns to the fax default screen. When originals remain in the document
processor, take them out.
NOTE
In some cases, transmission may take place even if the [Stop] key.
FAX Delayed Transmission
Set a send time. You can use delayed transmission together with the broadcast transmission function, etc.
The method for sending originals to one destination after setting the start time is explained here.
Item
Description
Off
Does not use the delayed transmission.
On
Uses the delayed transmission.
Start Time
Set the time from between 00:00 and 23:59 in one-minute increments.
IMPORTANT
If the current time displayed on the message display is not correct, you cannot send originals correctly at the
preset time. In this case, adjust the time. For details, refer to Setting Date and Time on page 1-6.
NOTE
You cannot select direct transmission.
You can set up to 30 destinations for delayed transmission.
When two or more delayed transmissions are set for the same time, the communication will start in the order that the
delayed transmissions have been set.
3-17
Sending Faxes > FAX TX Report
Cancelling Delayed Transmissions
Use the procedure below to cancel the delayed transmission.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
1 Press the [▲] or [▼] key to select [Status].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Scheduled Job].
4 Press the [OK] key.
Display the scheduled job screen.
2
Canceling a job.
1 Press the [▲] or [▼] key to select the job to cancel.
Scheduled Job:
0010
0123456789
0011
1234567890
0012
2345678901
Menu
Cancel
2 Press [Cancel].
3 Press [Yes] in confirmation screen. The selected job is deleted.
FAX TX Report
You can check whether FAX was transmitted properly by printing the report after transmission.
Item
Description
Off
Does not print reports.
On
Prints reports.
Error Only
Prints reports only if an error occurs.
NOTE
This setting is displayed if FAX TX Result Reports is set to [Specify Each Job]. For details, refer to FAX TX Result
Reports on page 8-5.
3-18
Sending Faxes > Program
Program
By registering sets of frequently used functions as a single program, you can simply select the program number as
needed to recall those functions. You can also name the programs for easy identification when recalling.
Registering Program
Use the procedure below to register a program.
1
Set the destination and transmitting functions.
Destination to which FAX is transmitted and transmitting functions need to be set in advance.
Methods For Entering the Destination  page 3-1
Fax transmission functions  page 3-13
2
Register the program.
1 Press the [Program] key.
2 Press the [▲] or [▼] key to select a program number (01 to 10) to register.
Select program:
01 Program 01
02 Program 02
03 Program 03
Menu
NOTE
Unregistered program numbers are displayed with [----------------].
If you select a program number already registered, the currently registered functions can be
replaced with a new set of functions.
3 Press [Menu].
4 Press the [▲] or [▼] key to select [Add].
5 Press the [OK] key.
NOTE
When the screen for selecting job type appears, press the [▲] or [▼] key to select [FAX]
and press the [OK] key.
6 Enter a program name using the numeric keys.
For details on character entry, refer to Character Entry Method on page 11-2.
7 Press the [OK] key. The program is registered.
3-19
Sending Faxes > Program
NOTE
Up to 32 characters can be entered.
If the program number is already used in any of the existing programs, the change
confirmation screen appears. Press [Yes].
The settings can be confirmed by recalling the program. Refer to Recalling Program on
page 3-20.
Confirming the Registered Program
The settings of the registered program can be confirmed by recalling the program. Refer to Recalling Program on page
3-20.
Recalling Program
Use the procedure below to recall a registered program.
1
Recall the program.
1 Press the [Program] key.
2 Press the [▲] or [▼] key to select a program number (01 to 10) to recall.
Select program:
01 Program 01
02 Program 02
03 Program 03
Menu
3 Press the [OK] key.
2
Execute the program.
Place the originals and press the [Start] key. Transmission starts.
Overwriting Program
Programs can be changed with the same procedures as those for registering programs. When selecting the program
number to be registered, select the program to be changed and overwrite the program number. Refer to Registering
Program on page 3-19.
3-20
Sending Faxes > Program
Changing the Program Name
Use the procedure below to change the program name.
1
Display the screen.
1 Press the [Program] key.
2 Press the [▲] or [▼] key to select a program number (01 to 10) to edit.
Select program:
01 Program 01
02 Program 02
03 Program 03
Menu
3 Press [Menu].
2
Edit the program name.
1 Press the [▲] or [▼] key to select [Edit Name].
2 Press the [OK] key.
3 Enter a program name using the numeric keys.
For details on character entry, refer to Character Entry Method on page 11-2.
4 Press the [OK] key.
5 Press [Yes] in the confirmation screen. The program is registered.
Deleting Program
Use the procedure below to delete a program.
1
Display the screen.
1 Press the [Program] key.
2 Press the [▲] or [▼] key to select a program number (01 to 10) to delete.
Select program:
01 Program 01
02 Program 02
03 Program 03
Menu
3 Press [Menu].
3-21
Sending Faxes > Program
2
Delete the program.
1 Press the [▲] or [▼] key to select [Delete].
2 Press the [OK] key.
3 Press [Yes] in the confirmation screen.
3-22
Sending Faxes > Using Chain Dial
Using Chain Dial
Chain dial is a function that allows you to dial by linking fax numbers of the receiving systems with a chain number
created with a number common to several destinations.
By setting multiple phone numbers from several telephone companies to a chain number, you can later choose the one
that costs the least to send the fax to a remote or international destination.
NOTE
It is convenient to register chain numbers that are used frequently to the Address Book or One-touch keys. For
registration to the Address Book, refer to Registering Destinations in the Address Book on page 2-2. For registration
to One-touch keys, refer to Adding a Destination on One Touch Key on page 2-12.
As an example, when using ‘212’ as the chain number
1
Press the [FAX] key.
2
Select the chain dial number
Enter the fax number to be added to the chain number. Select the address in which the chain
number is registered in the Address Book, One touch key or enter the chain number with the
numeric keys.
FAX No. Entry:
212
Chain
Detail
3
Press [Chain].
4
Enter the fax number to be added to the chain number.
Chain:
212
Detail
When entering the FAX number using the numeric keys, continue entering the FAX number.
When entering the FAX number from Address Book, select the FAX number by pressing the
[Address Book] key.
When selecting the FAX number using the One Touch Key, press the registered One Touch
Key.
For the procedure for selecting a destination in the address book, refer to Choosing from the
Address Book on page 3-10.
For the procedure for selecting the destination using the One Touch Key, refer to Choosing by One
Touch Key on page 3-12.
3-23
Sending Faxes > Using Chain Dial
5
Press the [OK] key.
Chain:
2120123456
Detail
To select the next fax number, repeat steps from step 2.
6
Press the [Start] key.
The transmission will start.
3-24
4
Receiving Faxes
This chapter explains the following topics:
FAX Automatic Reception .................................................................................................................................. 4-2
Reception Method .................................................................................................................................... 4-2
Flow of reception ..................................................................................................................................... 4-3
Manual Reception .............................................................................................................................................. 4-4
Using the Telephone to Receive .............................................................................................................. 4-4
Fax reception functions ...................................................................................................................................... 4-6
Fax reception settings ........................................................................................................................................ 4-6
Duplex Print Output ................................................................................................................................. 4-6
Reception Date/Time ............................................................................................................................... 4-6
Media Type for Print Output ..................................................................................................................... 4-6
4-1
Receiving Faxes > FAX Automatic Reception
FAX Automatic Reception
When using this machine as a FAX-dedicated machine that does not receive telephone calls, set the machine to FAX
dedicated reception. No special operation is required when receiving faxes.
Reception Method
This machine allows the following four reception methods.
•
Auto(Normal)
•
Auto(FAX/TEL) (Refer to 7-2.)
•
Auto(TAD) (Refer to 7-4.)
•
Manual (Refer to 4-4.)
Checking and Changing the Reception Method
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Reception].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [RX Settings].
7 Press the [OK] key.
2
Set the Reception method.
1 Press the [▲] or [▼] key to select the reception method.
For FAX Automatic Reception, select [Auto(Normal)].
2 Press the [OK] key.
4-2
Receiving Faxes > FAX Automatic Reception
Flow of reception
1
Reception Starts
When a fax comes in, the [Processing] indicator blinks and reception automatically begins.
NOTE
When a telephone (commercially available) is connected to the machine, reception starts
after the telephone rings.
You can change the number of times the ringing tone rings. (Refer to Reception on page 95.)
Memory Reception
When the machine cannot print a fax due to paper running out or a paper jams, it temporarily
stores originals that have been sent in the image memory. When the machine returns to the
printable state, printing starts.
The number of pages that can be stored depends on the pages. As a general guideline, about
250 or more A4 size pages at normal resolution can be stored.
During memory reception, FAX Reception Printing Jobs are displayed on Printing Jobs of the
Status screen. To print the received originals, supply paper or remove jammed paper.
For the Status screen, refer to the machine’s Operation Guide.
2
Reception Print
Received faxes are output to the tray with the printed side facing down.
Paper for printing received faxes is supplied from the cassette.
4-3
Receiving Faxes > Manual Reception
Manual Reception
This method allows you to receive faxes by pressing the [On hook] key after confirming that the telephone line has
connected to the sending system.
NOTE
To use Manual Reception, you need to change the receiving mode to Manual Reception. To change to manual mode,
refer to RX Settings on page 9-5.
Connecting a telephone set (commercially available product) to this machine enables you to receive originals after
talking to the person at the sending system.
Using the Telephone to Receive
You can confirm that the connection has been made before receiving a fax.
1
When there is an incoming call, the telephone connected to the machine
makes a ringing tone.
2
Lift the handset of the telephone.
3
Check if the telephone line has connected to the fax of the sending
system.
When you hear the fax tone
The sending system is on fax.
1 Press the [FAX] key.
2 Press the [On hook] key.
3 Press [ManualRX].
On Hook:
ManualRX
Reception will start.
NOTE
When using a telephone set that can send tone signals, use the telephone to start the
reception of originals with the remote switch function. (Refer to Remote Switch Function on
page 7-9.)
4-4
Receiving Faxes > Manual Reception
When you hear a voice from the receiving system
The telephone line has connected to the telephone of the sending system. When the
conversation is over, follow steps 1 to 3 above.
After the sending system has started transmission, the machine starts receiving originals.
4
When reception starts (when the [Processing] indicator on the operation
panel starts blinking), return the handset to its original position.
4-5
Receiving Faxes > Fax reception functions
Fax reception functions
The reception method and fax printing method can be set.
What do you want to do?
Reference Page
Print received faxes on both sides of the paper.
Duplex Print Output  page 4-6
Print the date and time of reception and other information.
Reception Date/Time  page 4-6
Restrict the type of paper that can be used.
Media Type for Print Output  page 4-6
Forward received faxes to another fax machine or a computer.
Forward Settings  page 5-2
Fax reception settings
Duplex Print Output
When received multiple pages of data are the same width, they can be printed out on both sides of paper having the
same width as the data.
NOTE
The optional duplex unit is required.
On
Print on both sides.
Off
Do not print on both sides.
For more information about configuring settings, refer to Default fax settings on page 9-2.
Reception Date/Time
Reception Date/Time function adds the reception date/time, sender information and number of pages on the top of each
page when the message is printed out. It is useful for confirming the time of reception if the fax is from a different time zone.
NOTE
When the received data is printed on multiple pages, the reception date/time is printed on
the fist page only. It is not printed on the pages that follow. When the received fax data is
forwarded after retrieving it from memory, the reception date/time is not added to the
forwarded data.
On
Print the reception date/time.
Off
Do not print the reception date/time.
For more information about configuring settings, refer to Default fax settings on page 9-2.
Media Type for Print Output
Specify the paper type to be used for print output of the received fax.
Supported paper types
All Media Type, Plain, Rough, Vellum, Recycled, Bond, Color, Thick, High
Quality, Custom 1-8
For more information about configuring settings, refer to Default fax settings on page 9-2.
Setting the cassette for the print output of received faxes
By specifying the media type, faxes can be received on the corresponding cassette.
4-6
Receiving Faxes > Fax reception settings
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Common Settings].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Orig./Paper Set.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select the cassette ([Cassette 1 (to 4) Set.]) you want to use for
fax reception.
7 Press the [OK] key.
2
Selecting the paper size.
1 Press the [▲] or [▼] key to select [Cassette 1 (to 4) Size].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Auto].
4 Press the [OK] key.
5 Press the [▲] or [▼] key to select [Metric] or [Inch].
6 Press the [OK] key.
7 Press the [Back] key.
IMPORTANT
Specify the paper size as follows for the cassette that you want to use for fax
reception.
Metric models: Select [Auto] and then [Metric].
Inch models: Select [Auto] and then [Inch].
3
Selecting the paper type.
1 Press the [▲] or [▼] key to select [Cassette 1 (to 4) Type].
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select the paper type you want to use for fax reception.
4 Press the [OK] key.
4
Set the paper type.
Configure paper settings for fax reception. When selecting the paper type, select the same paper type as
you selected in step 3.
For more information about configuring settings, refer to Default fax settings on page 9-2.
4-7
Receiving Faxes > Fax reception settings
4-8
5
Using Convenient Fax
Functions
This chapter explains the following topics:
Forward Settings ................................................................................................................................................ 5-2
Setting Forwarding ...................................................................................................................................
Registering Forwarding Destination .........................................................................................................
Forwarding Time Setting ..........................................................................................................................
Print Setting .............................................................................................................................................
5-1
5-2
5-3
5-7
5-8
Using Convenient Fax Functions > Forward Settings
Forward Settings
When you have received a fax, you can forward the received image to other fax machine, or set printing.
Setting Forwarding
Use the procedure below to set forwarding.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Reception].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Forward Settings].
7 Press the [OK] key.
8 Press the [▲] or [▼] key to select [Forwarding].
Forward Settings:
01 Forwarding
02 Forward Dest.
03 Forward Time
Exit
9 Press the [OK] key.
2
Configure the function.
1 To set Forwarding, press the [▲] or [▼] key to select [On].
NOTE
When not using Forwarding, select [off].
2 Press the [OK] key.
5-2
Using Convenient Fax Functions > Forward Settings
Registering Forwarding Destination
Use the procedure below to register a forwarding destination.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Reception].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Forward Settings].
7 Press the [OK] key.
8 Press the [▲] or [▼] key to select [Forward Dest.].
Forward Settings:
01 Forwarding
02 Forward Dest.
03 Forward Time
Exit
9 Press the [OK] key.
2
Registering Forwarding Destination
Selecting Forwarding Destination from Address Book
1 Press the [▲] or [▼] key to select [Add Destination].
Forward Dest.:
01 Confirmation
02 Add Destination
Exit
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Address Book].
4 Press the [OK] key.
5-3
Using Convenient Fax Functions > Forward Settings
5 Press the [▲] or [▼] key to select the destination.
Contacts:
Sales Department 1
Sales Department 2
Sales Department 3
Menu
NOTE
When selecting the destination, press [Menu] and then [▲] or [▼] key, select
[Search(Name)], and then press the [OK] key. The Search screen is displayed.
When checking details of the destination, press the [▲] or [▼] key to select the destination
to check details, press [Menu] and then [▲] or [▼] key, select [Details], and then press the
[OK] key. Detailed information is displayed.
6 Press the [OK] key.
Entering Forwarding Destination Directly
1 Press the [▲] or [▼] key to select [Add Destination].
Forward Dest.:
01 Confirmation
02 Add Destination
Exit
2 Press the [OK] key.
3 Press the [▲] or [▼] key to select [Address Entry].
4 Press the [OK] key.
5 Enter the FAX number of the forwarding destination using the numeric keys.
FAX No. Entry:
0123456789
Detail
NOTE
When changing TX Start Speed or ECM settings, press [Details] and change the settings.
6 Press the [OK] key.
5-4
Using Convenient Fax Functions > Forward Settings
Changing and Deleting Registration Contents
Use the procedure below to change or delete registration contents.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Reception].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Forward Settings].
7 Press the [OK] key.
8 Press the [▲] or [▼] key to select [Forward Dest.].
Forward Settings:
01 Forwarding
02 Forward Dest.
03 Forward Time
Exit
9 Press the [OK] key.
2
Changing Forwarding Destination
When the fax number of the destination was entered with the numeric keys
The fax number, TX Start Speed, and ECM can be changed.
1 Press the [▲] or [▼] key to select [Confirmation].
Forward Dest.:
01 Confirmation
02 Add Destination
Exit
2 Press the [OK] key.
3 Check the destination you want to change.
Dest. Confirm.:
0123456789
...
Exit
4 Press the [OK] key.
5-5
Using Convenient Fax Functions > Forward Settings
5 Press the [▲] or [▼] key to select [Detail/Edit].
6 Press the [OK] key.
7 Reenter the FAX number of the forwarding destination using the numeric keys.
NOTE
When changing TX Start Speed or ECM settings, press [Details] and change the settings.
8 Press the [OK] key.
When the destination was selected from the Address Book
The information stored in the destination can be checked.
1 Press the [▲] or [▼] key to select [Confirmation].
Forward Dest.:
01 Confirmation
02 Add Destination
Exit
2 Press the [OK] key.
3 Check the destination.
Dest. Confirm.:
ABCDEF
...
Exit
4 Press the [OK] key.
5 Press the [▲] or [▼] key to select [Detail/Edit].
6 Press the [OK] key.
7 Press the [] or [] key to check details of the destination.
NOTE
You can check Contact Name, FAX Number and Address Number. You can check the
settings of TX Start Speed and ECM by pressing [Details] on the FAX Number screen.
8 Press the [OK] key.
To delete the forwarding destination
9 Press the [▲] or [▼] key to select [Confirmation].
Forward Dest.:
01 Confirmation
02 Add Destination
Exit
10Press the [OK] key.
5-6
Using Convenient Fax Functions > Forward Settings
11Press the [OK] key.
Dest. Confirm.:
0123456789
...
Exit
12Press the [▲] or [▼] key to select [Delete].
13Press the [OK] key.
14Press [Yes] in confirmation screen.
Forwarding Time Setting
Register the start time and end time between which forwarding is enabled.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Reception].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Forward Settings].
7 Press the [OK] key.
8 Press the [▲] or [▼] key to select [Forward Time].
Forward Settings:
01 Forwarding
02 Forward Dest.
03 Forward Time
Exit
9 Press the [OK] key.
5-7
Using Convenient Fax Functions > Forward Settings
2
Configure the function.
1 Press the [▲] or [▼] key to select [All day] or [Preset Time].
Forward Time:
01 *All day
02 Preset Time
To forward all day, select [All day] and press the [OK] key.
To set a forwarding start time and end time, select [Preset Time] and press the [OK] key, and
then set the start time and end time.
Forwarding start time and end time settings
1 Press the [▲] or [▼] key to set the hours and minutes of the start time. Press the [◄] and
[►] key to move the cursor right and left.
Start Time:
Hour
Min.
00 :
00
(Current Time 11:45)
2 Press the [OK] key.
3 Press the [▲] or [▼] key to set the hours and minutes of the end time. Press the [◄] and
[►] key to move the cursor right and left.
End Time:
Hour
Min.
00 :
00
(Current Time 11:45)
4 Press the [OK] key.
Print Setting
You can set whether the machine should print received originals when forwarding them.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Reception].
5 Press the [OK] key.
5-8
Using Convenient Fax Functions > Forward Settings
6 Press the [▲] or [▼] key to select [Forward Settings].
7 Press the [OK] key.
8 Press the [▲] or [▼] key to select [Print].
Forward Settings:
04 Print
Exit
9 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [On] (print) or [Off] (do not print).
2 Press the [OK] key.
5-9
6
Sending Faxes from
PC
This chapter explains the following topics:
Flow of Sending Faxes from PC ........................................................................................................................ 6-2
Setup .................................................................................................................................................................. 6-3
Connection to a PC .................................................................................................................................. 6-3
Installing the FAX Driver .......................................................................................................................... 6-3
Uninstalling the FAX Driver ...................................................................................................................... 6-5
Basic Transmission ............................................................................................................................................ 6-6
Configuring the Driver Default Settings ................................................................................................... 6-8
Default Settings Dialog Box ..................................................................................................................... 6-9
6-1
Sending Faxes from PC > Flow of Sending Faxes from PC
The FAX Driver function makes it possible to send faxes from any computer connected by USB or network cable. Its
primary features include the following.
•
PC-prepared document can be sent by fax without being printed out.
•
An Address Book (in the machine/PC) can be used to specify a desired destination.
•
Addition of a cover page.
•
Operation is as simple as printing.
Flow of Sending Faxes from PC
Sending faxes from PC is performed in the following sequence.
Prepare a document using a PC connected to this machine.
▼
Forward the document data from the PC to this machine using the same
operation as for printing.
▼
The machine sends the document data to another fax machine.
▼
The other fax machine receives the data.
6-2
Sending Faxes from PC > Setup
Setup
Connection to a PC
Connect the machine to a PC using the network cable or USB cable. For details, refer to the machine’s
Operation Guide.
Installing the FAX Driver
The procedure for installing the FAX Driver is explained below. (The screens in Windows 7 are
shown.)
NOTE
Plug and Play is disabled on this device when in Sleep. Wake the device from Sleep before
continuing.
1
Insert the Product Library disc.
NOTE
Installation on Windows must be done by a user logged on with administrator privileges.
If the "Welcome to the Found New Hardware Wizard" dialog box displays, select [Cancel].
If the autorun screen is displayed, click [Run Setup.exe].
If the user account management window appears, click [Yes] ([Allow]).
2
Display the screen.
1
2
Click [View License Agreement] and read the License Agreement. Click [Accept].
6-3
Sending Faxes from PC > Setup
3
Select FAX Driver.
1
2
3
1 Select [Custom Install].
2 Select the print system to be installed.
3 Click [
].
4
5
6
4 Select [FAX Driver].
5 Click [
].
6 Click [Install].
NOTE
• The machine cannot be detected unless it is on. If the computer fails to detect the
machine, verify that it is connected to the computer via a network or USB cable and that it
is turned on and click
(Reload).
• If the Windows security window appears, click [Install this driver software anyway].
4
Finish the installation.
If a system restart message appears, restart the computer by following the screen prompts.
This completes the FAX driver installation procedure.
6-4
Sending Faxes from PC > Setup
Uninstalling the FAX Driver
Perform the following procedure to delete the FAX Driver from your computer.
NOTE
Uninstallation on Windows must be done by a user logged on with administrator privileges.
1
Display the screen.
2
Uninstall the software.
Click [Start] button on the Windows and then select [All Programs], [Kyocera], and
[Uninstall Kyocera Product Library] to display the Uninstall Wizard.
Place a check in the check box of the driver to be deleted and click [Uninstall].
1
2
3
Finish uninstalling.
If a system restart message appears, restart the computer by following the screen prompts.
This completes the software uninstallation procedure.
NOTE
The software can also be uninstalled using the Product Library.
In the Product Library installation screen, select to uninstall, and follow the on-screen
instructions to uninstall the software.
6-5
Sending Faxes from PC > Basic Transmission
Basic Transmission
1
Create the document to be sent.
1 Use an application on your computer to create the document to be sent.
2 Set the original size and orientation.
3 Select [Print] from the File menu. The Print dialog box for the application that you are using
will appear.
3
1
2
2
Select settings in the Print dialog box.
1 Select the product name of the machine to be used in the printer name list.
2 Set the print range and other settings.
NOTE
Make sure that the number of copies is set to 1. The following screen is an example. The
actual dialog box will vary depending on the application that you are using.
3 Click [Properties] to open the Properties window.
3
Select settings on the FAX Setting tab.
1 Specify fax settings such as the original size on the FAX Setting tab, and click [OK].
6-6
Sending Faxes from PC > Basic Transmission
NOTE
For detailed information on the settings on the tab, refer to FAX Driver User Guide.
2 You will return to the Print dialog box for the application. Click [OK]. The Transmit Settings
dialog box will appear.
4
Select settings in the Transmit Settings dialog box.
Transmission time can be set.
NOTE
For details on the settings, refer to FAX Driver User Guide.
5
Specify a cover page.
To include a cover page, select settings on the [Cover Page] tab.
NOTE
For details on the settings, refer to FAX Driver User Guide.
6
Set the destination.
1 Use the keyboard to enter the destination fax number in the [Address Setting] tab.
2 Click [Add to Destination List].
The destination information will appear in the address list. To send to multiple destinations,
repeat this operation.
6-7
Sending Faxes from PC > Basic Transmission
3 To use the Address Book, click [Select from Address Book] and select the destination.
7
Click [Send]. Transmission will begin.
Configuring the Driver Default Settings
Use the FAX Setting tab of the print settings screen to set the original size and other transmission conditions.
1
Display the screen.
1 From the start button, click [Control Panel], [Hardware and Sound], and [Devices and
Printers].
2 Right-click the product name of the machine you are using and select [Printing
preferences] from the pull-down menu. The Printing Preferences screen will open.
6-8
Sending Faxes from PC > Basic Transmission
2
Select settings.
The following settings can be specified.
Item
Description
Page Size
Select the size of the document being transmitted from the drop-down list.
Available settings: Letter (8.5 x 11 in.), Legal (8.5 x 14 in.), Ledger (11 x 17
in.), Statement (5.5 x 8.5 in.), A3 (11.69 x 16.54 in.), A4 (8.27 x 11.69 in.),
A5 (5.83 x 8.27 in.), Folio (8.27 x 12.99 in.), B4 (9.84 x 13.90 in.),
B5(JIS)(7.17 x 10.12 in.)
Orientation
Specify whether the orientation of the document is portrait or landscape.
Available settings: Portrait, Landscape
Resolution
Select the resolution of the document to be transmitted.
Available settings: 200x100dpi Normal, 200x200dpi Fine
FAX TX Setting
Click [FAX TX Setting] to change the default settings for fax transmission.
The [Default Settings] screen will appear.
Default Settings Dialog Box
By setting the transmission conditions that you use most in this dialog box, you can minimize the need to change the
settings each time.
The Default Settings dialog box can be accessed by the following procedure:
1
Display the screen.
1 Click the [Start] button on the taskbar, click [Control Panel], and then click [View devices
and printers].
2 Right click the name of the machine to be used as the network fax and select [Printing
preferences] from the resulting pull-down menu. Click the [FAX TX Setting] button in the
[Printing Preferences] window.
2
Configure the settings.
(1) Sender Information Tab
Enter your own information into fields explained below to send a cover page with your faxes.
6-9
Sending Faxes from PC > Basic Transmission
Item
Description
Company
A maximum of 64 characters can be entered.
Department
A maximum of 64 characters can be entered.
Name
A maximum of 32 characters can be entered.
Telephone Number
A maximum of 20 characters can be entered (Entry is allowed for the
characters 0 to 9, #, *, -, (, ), +, and spaces.)
FAX Number
A maximum of 20 characters can be entered (Entry is allowed for the
characters 0 to 9, #, *, -, (, ), +, and spaces.)
Sender Information List
Sender Information can be selected from the Sender Information List. The
selected item is highlighted.
Add
Add Sender Information to the Sender Information List.
Save
Save the edited Sender Information List.
Delete
Delete the selected item from the Sender Information List.
(2) Cover Page Tab
Item
Attach Cover Page
checkbox
Description
Check the checkbox when you want to add a cover page to your
transmission.
NOTE
For information regarding the Cover Page registration method, refer to FAX Driver User
Guide.
6-10
Sending Faxes from PC > Basic Transmission
(3) Authentication Tab
Item
Description
Job Accounting
checkbox
If the fax machine is set to Job Accounting, select either Use Specific
Account ID or Prompt for Account ID as desired.
Use Specific Account ID: Enter the Account ID. Transmission will be
performed using the entered Account ID.
Prompt for Account ID: A screen for entering the Account ID will be
displayed when attempting a transmission. The Account ID must be entered
each time a transmission is attempted.
(SNMP) Settings
Configure SNMP settings.
(4) Sending Options Tab
6-11
Sending Faxes from PC > Basic Transmission
Item
FAX Delayed Transmit
checkbox
Description
Check the checkbox in order to activate the time fields to the right of the
checkbox whenever you want to set the time that your documents will be
transmitted. The desired time setting can be entered directly with the
keyboard or by clicking on the  and  arrows.
IMPORTANT
If the time that is shown in the message display of this fax
machine does not match the current time, communications
that use the timer may not be accomplished as expected. If
the displayed time is not current, be sure to adjust it to
match the correct time.
NOTE
If you designate a time that is earlier in the day than the time that
is actually displayed in the fax machine itself, the transmission
operation will be carried out the following day at that time. Be
sure to confirm the time setting in the fax machine itself before
making this setting.
Available settings: 00:00-23:59
6-12
7
Using a Connected
Telephone
This chapter explains the following topics:
FAX/TEL Auto Switch Reception ....................................................................................................................... 7-2
FAX/Answering Machine Auto Switch Reception ............................................................................................... 7-4
Manual Send ...................................................................................................................................................... 7-6
Manual Reception .............................................................................................................................................. 7-7
Remote Switch Function .................................................................................................................................... 7-9
7-1
Using a Connected Telephone > FAX/TEL Auto Switch Reception
FAX/TEL Auto Switch Reception
This reception method is convenient when using both telephone and fax on a single telephone line. When fax originals
have been sent, the machine automatically receives them, and when the other party is calling from a telephone, the
machine makes a ringing tone urging the user to respond.
IMPORTANT
In order to use FAX/TEL Auto Switch Reception, it is necessary to connect a
telephone set (commercially available product) to the machine.
After the telephone has made a ringing tone for the preset number of times, the other
party is required to pay phone line charges even if the receiving system does not
respond.
Flow of reception
FAX
FAX
Telephone
When the other party has sent
originals with automatic send
When the other party has sent
originals with manual send
When the other party is calling
from a telephone
Receives incoming call without making ringing tone.
(The other party is required to pay the phone line charge from this point.)
Makes ringing tone twice.
(Only the other party can hear the ringing tone.)
Receive originals from the other
party automatically (FAX
Automatic Reception)
Makes ringing tone. (Both the other party and the receiving
machine can hear the ringing tone.)
(If you do not lift the handset of the telephone within 30 seconds,
the machine switches to fax reception.)
When you lift the handset of the connected telephone set, you can
talk to the other party.
After the end of the
conversation, you can receive
faxes by using the Remote
Switch Function.
NOTE
At the end of the conversation, you can also receive faxes by using the Remote Switch
Function. (Refer to Remote Switch Function on page 7-9.)
Preparation:
Refer to RX Settings on page 9-5 to select [Auto(FAX/TEL)].
7-2
Using a Connected Telephone > FAX/TEL Auto Switch Reception
1
The telephone rings.
The connected telephone set makes a ringing tone. Note that if [0] (zero) is set as the number
of rings (for FAX/TEL Auto Switch), the connected telephone does not ring.
NOTE
You can change the number of times the ringing tone rings. (Refer to Reception on page 95.)
2
Answer the call.
When the call is from a telephone
1 The machine makes a ringing tone urging the user to respond. Lift the handset of the
telephone within 30 seconds.
NOTE
If you do not lift the handset within 30 seconds, the machine switches to fax reception.
2 Talk to the other party.
NOTE
At the end of the conversation, you can also receive faxes by using the Remote Switch
Function. (Refer to Remote Switch Function on page 7-9.)
When the call is from a fax
The machine starts receiving fax originals.
7-3
Using a Connected Telephone > FAX/Answering Machine Auto Switch Reception
FAX/Answering Machine Auto Switch Reception
This method is convenient when using both the answering machine and fax. When fax originals have been sent, the
machine receives them automatically, and when the call is from a telephone, the machine follows the functions of the
connected answering machine. Therefore, when the user is absent, the other party can leave a message on the
answering machine.
IMPORTANT
When using FAX/Answering Machine Auto Switch Reception function, if a silence
continues for at least 30 seconds before one minute passes after the machine has
received a call from the other party, the machine’s silence detection function comes
into operation and the machine switches to fax reception.
NOTE
In order to use FAX/Answering Machine Auto Switch Reception, it is necessary to connect
an answering machine-equipped telephone set (commercially available product) to the
machine.
For details, such as responding to messages, refer to the Operation Guide of each
answering machine.
Set the number of rings to be made by the machine more than the number of rings to be
made by the answering machine. (Refer to Reception on page 9-5.)
Flow of reception
FAX
FAX
Telephone
When the other party has sent
originals with automatic send
When the other party has sent
originals with manual send
When the other party is calling
from a telephone
Receive fax originals from the
other party automatically (FAX
Automatic Reception).
The answering machine plays the message informing the other
party that the user is absent.
The answering machine records a message from the other party.
When the other party starts
sending originals, the machine
receives the originals being
sent.
Preparation:
Refer to RX Settings on page 9-5 to select [Auto(TAD)].
7-4
Using a Connected Telephone > FAX/Answering Machine Auto Switch Reception
1
The telephone rings.
The connected telephone set makes ringing tone the set number of times.
NOTE
If you lift the handset while the telephone set is still making the ringing tone, the machine
enters a status the same as manual reception. (Refer to Manual Reception on page 7-7.)
2
The answering machine responds.
When the call is from a telephone, but the user is absent
The answering machine plays a response message, and starts recording the other party’s
message.
NOTE
When silence continues for at least 30 seconds during recording, the machine switches to
fax reception.
When the call is from a fax
The machine starts receiving fax originals.
7-5
Using a Connected Telephone > Manual Send
Manual Send
When you want to talk to the person at the receiving system or the receiving system needs to switch to fax, use this
method to send originals.
1
Place the originals.
2
Dial the destination.
Lift the handset, and dial the number of the receiving system.
3
Check if the telephone line has connected to the fax of the receiving
system.
If the destination is a fax machine, you will hear a long high beep sound. If a person answers,
you can talk to that person.
4
Press the [On hook] key.
1 Press the [FAX] key.
2 Press the [On hook] key.
5
Press the [Start] key.
Transmission begins.
6
Replace the handset.
When sending starts, return the handset to its original position.
7-6
Using a Connected Telephone > Manual Reception
Manual Reception
Use this method when you want to receive originals after talking to the person at the sending system.
NOTE
FAX Automatic Reception has been preset for the receiving mode of this machine. To use
Manual Reception, you need to change the receiving mode to Manual Reception. To change
to manual mode, refer to RX Settings on page 9-5.
1
The telephone rings.
2
Lift the handset.
When there is an incoming call, the telephone connected to the machine makes a ringing tone.
Lift the handset of the telephone.
3
Check if the telephone line has connected to the fax of the sending
system.
If the destination is a fax machine, you will hear soft beep sounds. If a person answers, you
can talk to that person.
4
Press the [On hook] key.
1 Press the [FAX] key.
2 Press the [On hook] key.
7-7
Using a Connected Telephone > Manual Reception
5
Press [ManualRX].
On Hook:
ManualRX
Reception will start.
NOTE
When using a telephone set that can send tone signals, use the telephone to start the
reception of originals with the remote switch function. (Refer to Remote Switch Function on
page 7-9.)
6
Replace the handset.
When reception starts, return the handset to its original position.
7-8
Using a Connected Telephone > Remote Switch Function
Remote Switch Function
You can start fax reception by operation from the connected telephone set. This function is convenient for using this
machine and a telephone set (commercially available product) in combination installed at places distant from each other.
NOTE
In order to use remote switch, it is necessary to connect the tone signal-sending telephone
set (commercially available product) to the machine. However, even if it is a tone signalsending telephone set, this function may not be used satisfactorily depending on the type of
telephone set. For details, contact our agent or the store where you purchased this
machine.
The remote switch dial is set to 55 at the factory.
The remote switch dial number can be changed. Refer to Reception on page 9-5.
Using the Remote Switch Dial
To start fax reception by operation from the connected telephone set, use the following
operation.
1
The connected telephone set makes a ringing tone.
Lift the handset of the telephone.
NOTE
You can change the number of times the ringing tone rings. (Refer to Reception on page 95.)
2
Press the remote switch dial number (2 digits).
When you hear the fax tone from the handset, enter the two-digit remote switch dial number
using the dial button on the telephone set. The telephone line switches to the machine, and
reception starts.
7-9
8
Checking
Communication
Status and Machine
Information
This chapter explains the following topics:
Verious Reports for FAX ..................................................................................................................................... 8-2
Checking FAX Job History ................................................................................................................................. 8-3
Send Job Log and Print Job Log ............................................................................................................. 8-3
Outgoing FAX Log and Incoming FAX Log .............................................................................................. 8-4
Printing Administrative Reports .......................................................................................................................... 8-5
FAX TX Result Reports ............................................................................................................................ 8-5
FAX RX Result Reports ........................................................................................................................... 8-6
Activity Report .................................................................................................................................................... 8-7
Printing Activity Reports ........................................................................................................................... 8-7
Automatic Printout ................................................................................................................................... 8-8
Status Page ........................................................................................................................................................ 8-9
8-1
Checking Communication Status and Machine Information > Verious Reports for FAX
Verious Reports for FAX
Check the fax transmission results and registration status using the following tools.
Reports
FAX job history
check
Display
Location
Message display
Menu
Contents to
Check
Timing of Check
Reference
Page
Send Job Log
Print Job Log
History of latest 16
send and receipt
results stored
(including jobs other
than FAX jobs)
Any time
8-3
Outgoing FAX Log
Incoming FAX Log
History of latest 50
send and receipt
results stored (FAX
jobs only)
Any time
8-4
Send result report
/ Receipt result
report
Report printing
FAX TX Result
FAX RX Result
Latest send or receipt
result
Automatic printout after
every sending or
receiving operation (No
Print Output or Error Only
is also optionally
available.)
8-5
Activity report
Report printing
Outgoing FAX Rpt
Incoming FAX Rpt
Latest 50 send or
receipt results
Any time, and automatic
printout after every 50
sending/receiving
8-7
Status page
Report printing
Status Page
Registration status of
Local FAX Number,
Local FAX Name, fax
line setting, etc.
Any time
8-9
8-2
Checking Communication Status and Machine Information > Checking FAX Job History
Checking FAX Job History
Send Job Log and Print Job Log
You can display the history of the latest 16 each of send (including scan jobs) and receipt (including copy and print jobs)
results on the message display for checking.
NOTE
Even when job accounting is enabled, 16 each of send and receipt results are displayed regardless of the account ID.
For details of the job history check, refer to the machine’s Operation Guide.
Displaying Job Log Screen
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Status].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Print Job Log] to check reception results, or [Send Job
Log] to check transmission results.
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select the job you want to check.
Send Job Log:
0004
0123456789
0003
1234567890 ...
0002
2345678901 ...
Detail
7 Press [Detail].
2
Check the status.
Press the [◄] or [►] key to check the details of the job.
0004 Detail:
Result:
OK
1/ 8
8-3
Checking Communication Status and Machine Information > Checking FAX Job History
Outgoing FAX Log and Incoming FAX Log
Display the history of the latest 50 each of send and receipt results on the display for checking.
NOTE
Even when job accounting is enabled, 50 each of send and receipt results are displayed regardless of the account ID.
For details of the job history check, refer to the machine’s Operation Guide.
Displaying Job Log Screen
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Status].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [FAX].
5 Press the [OK] key.
6 Check the status of communication.
FAX:
Ready.
Log
7 Press [Log].
8 Press the [▲] or [▼] key to select [Outgoing FAX Log] to check transmission results, or
[Incoming FAX Log] to check reception results.
9 Press the [OK] key.
2
Check the status.
Press the [◄] or [►] key to check the details of the job.
Outgoing FAX Log:
1/50
0123456789
OK
Detail
8-4
Checking Communication Status and Machine Information > Printing Administrative Reports
Printing Administrative Reports
You can print various administrative reports to check the results of fax transmission or the status of the functional setup.
FAX TX Result Reports
Each time you send a fax, you can print a report to confirm whether the fax was sent successfully. You can also print the
transmitted image in the fax tx result report.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Report].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Result Rpt Set.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [FAX TX Result].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [Off] (not to print), [On] (to print), [Error Only], or [Specify
Each Job].
2 Press the [OK] key.
If you selected [On], [Error Only] or [Specify Each Job], printing of the transmitted image
can be set.
3 Press the [▲] or [▼] key to select [Off] (not printing the transmitted image) or [On] (printing
the transmitted image).
4 Press the [OK] key.
Send Result Report
Send Result Report
8-5
Checking Communication Status and Machine Information > Printing Administrative Reports
FAX RX Result Reports
Each time you receive a fax, you can print a report to confirm whether the fax was received successfully.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Report].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Result Rpt Set.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [FAX RX Result].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [Off] (not to print), [On] (to print), [Error Only].
2 Press the [OK] key.
FAX RX Result Report
8-6
Checking Communication Status and Machine Information > Activity Report
Activity Report
Activity reports are reports of both the sent faxes and the received faxes. Each report lists the history of the latest 50
sent or received fax data. When automatic printout is selected, a report is printed out automatically after every 50 faxes
sent or received.
Printing Activity Reports
The latest 50 sent or received fax data are printed as a report.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Status].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [FAX].
5 Press the [OK] key.
2
Print
1 Press [Log].
FAX:
Ready.
Log
2 Press the [▲] or [▼] key to select [Outgoing FAX Rpt] to print the sent fax report, or
[Incoming FAX Rpt] to print the received fax report.
3 Press the [OK] key.
4 Press [Yes] in confirmation screen. The report is printed.
FAX TX Report
FAX RX Report
8-7
Checking Communication Status and Machine Information > Activity Report
Automatic Printout
An activity report is printed out automatically after every 50 faxes sent or received.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Report].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Admin Rpt Set.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Outgoing FAX Rpt] or [Incoming FAX Rpt].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [Off] (not to print) or [On] (to print).
2 Press the [OK] key.
8-8
Checking Communication Status and Machine Information > Status Page
Status Page
A status page provides information on a number of user setups. FAX-related information includes the Local FAX
Number, Local FAX Name, fax line setting, etc. You can print it out as necessary.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Report].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Report Print].
5 Press the [OK] key.
2
Print
1 Press the [▲] or [▼] key to select [Status Page].
2 Press the [OK] key.
3 Press [Yes] in confirmation screen. A status page is printed.
Status Page
8-9
9
Fax Settings
This chapter explains the following topics:
Default fax settings ............................................................................................................................................ 9-2
System Menu Settings .............................................................................................................................
Report ......................................................................................................................................................
Common Settings ....................................................................................................................................
FAX ..........................................................................................................................................................
9-2
9-3
9-3
9-4
Transmission Restriction .................................................................................................................................... 9-8
Registering Permit FAX No. ..................................................................................................................... 9-9
Changing and Deleting Permit FAX No. .................................................................................................. 9-9
Registering Reject FAX No. ................................................................................................................... 9-10
Changing and Deleting Reject FAX No. .................................................................................................. 9-11
Setting Send Restriction ........................................................................................................................ 9-12
Setting Reception Restriction ................................................................................................................ 9-13
Unknown Number Reception ................................................................................................................. 9-13
Unusable Time ................................................................................................................................................. 9-15
Account Management ...................................................................................................................................... 9-17
Logging in when Job Accounting has been Enabled ............................................................................. 9-18
9-1
Fax Settings > Default fax settings
Default fax settings
This section explains the fax settings in the system menu.
Press the [Status/System Menu/Counter] key to show the settings on the message display. Then, select from the
settings displayed.
Refer to Operation Method on page 1-5.
1
Cancels the current menu setting to
return to the menu one level higher.
2
Selects the item displayed or
changes the numeric value.
Confirms the selected setting.
NOTE
If the login user name entry screen appears during operations, log in by referring to the machine's Operation Guide for
Administrator User Name and Password.
The factory default login user name and login password are set as shown below.
Login User Name
Login Password
Admin*1
Admin*1
*1 Upper case and lower case letters are distinguished (case sensitive).
Refer to System Menu Settings on the following page and configure as needed.
System Menu Settings
Settings for the fax function in the system menu are shown below.
NOTE
For settings other than fax settings, refer to the Operation Guide for the machine.
Item
Description
Reference
Page
Report
Print reports to check the machine settings and status. Default settings
for printing the result reports can also be configured.
9-3
Common Settings
Configures overall machine operation.
9-3
FAX
Configures settings for fax functions.
9-4
Edit Destination
Configures Address Book settings. For details on Address Book, refer to
Registering Destinations in the Address Book on page 2-2.
2-2
9-2
Fax Settings > Default fax settings
Report
Print reports to check the machine settings and status. Default settings for printing the result reports can also be
configured.
Item
Report
Print
Description
Status Page
A status page provides information on a number of user setups. FAXrelated information includes the Local FAX Number, Local FAX Name, fax
line setting, etc. You can print it out as necessary.
Refer to Status Page on page 8-9.
Admin Rpt
Set.
Outgoing FAX Rpt
An activity report is printed out automatically after every 50 faxes sent.
Value: Off, On
Refer to Activity Report on page 8-7.
Incoming FAX Rpt
An activity report is printed out automatically after every 50 faxes
received.
Value: Off, On
Refer to Activity Report on page 8-7.
Result Rpt
Set.
FAX TX Result
Each time you send a fax, you can print a report to confirm whether the
fax was sent successfully.
Value: Off, On, Error Only, Specify Each Job
Refer to FAX TX Result Reports on page 8-5.
Attach SendImage
FAX RX Result
When [On], [Error Only] or [Specify Each Job] is selected, the transmitted
image is added to the report.
Value: Off, On
When a fax is received, you can be notified by receipt result report.
Value: Off, On, Error Only
Refer to FAX RX Result Reports on page 8-6.
Common Settings
Configures overall machine operation.
Sound
Item
Description
FAX Speaker Volume
Adjust the volume of the speaker.
Speaker Volume: Volume of the built-in speaker when the line is connected by pressing the [On
hook] key.
Value: 5 Maximum, 4, 3 Medium, 2, 1 Minimum, 0 Mute
FAX Monitor Volume
Adjust the volume of the monitor.
Monitor Volume: Volume of the built-in speaker when the line is connected without pressing the
[On hook] key such as in memory transmission.
Value: 5 Maximum, 4, 3 Medium, 2, 1 Minimum, 0 Mute
Orig./Paper Set. (Original/Paper Settings)
Configure settings for originals and paper. For details, refer to the machine’s Operation Guide.
9-3
Fax Settings > Default fax settings
Date Setting
Set the date and time for the location where you use the machine. For details, refer to Setting Date and Time on page 16.
Timer Setting
Item
Unusable Time
Description
This feature sets a time period during which the machine will not print received faxes. For
details, refer to Unusable Time on page 9-15.
Function Defaults
Item
FAX Resolution
Description
Select the default scanning resolution.
Value: 200x100dpi Norm., 200x200dpi Fine, 200x400dpi S.Fin
FAX
Settings related to the fax function can be configured.
Transmission
Item
Description
TTI
The transmit terminal identification (TTI) is the information about the machine (transmit
terminal) to be printed out on the fax on the receiving system.
The information includes transmission date and time, the number of transmission pages, and
the fax number.
Value: Off, On
Refer to TTI (Transmit Terminal Identification) on page 1-8.
Local FAX Name
Register the local FAX name printed in the transmit terminal identification (TTI) area.
Refer to Local FAX Name on page 1-8.
Local FAX Number
Register the local FAX number printed in the transmit terminal identification (TTI) area.
Refer to Local FAX Number on page 1-9.
FAX Dialing Mode
Select the telephone line according to the type you are contracted with. Please note that
selecting a wrong telephone line will prevent you from sending fax.
Refer to FAX Dialing Mode on page 1-10.
NOTE
This setting does not appear in some regions.
Retry Times
The number of retry times can be changed automatically.
9-4
Fax Settings > Default fax settings
Item
ECM TX
Description
Set whether ECM TX is performed.
ECM is a communication mode specified by the ITU-T (International Telecommunication Union)
that retransmits data when an error occurs. Fax machines that have ECM mode check for
errors as they communicate, preventing distortion of the image due to noise on the line and
other conditions.
Value: On, Off
NOTE
When there is a large amount of noise on the line, communication may take slightly
longer than when [Off] is selected.
TX Start Speed
Set the TX Start Speed.
When communication conditions are bad, the fax may not be transmitted correctly. In that case,
set a lower TX Start Speed.
Value: 9600bps, 14400bps, 33600bps
NOTE
Normally this should be used with the default setting.
Reception
Item
Description
FAX Media Type
Specify the paper type to be used for print output of the received fax.
Value: All Media Type, Plain, Rough, Vellum, Recycled, Bond, Color, Thick, High Quality,
Custom 1-8
Refer to Media Type for Print Output on page 4-6.
Rings(Normal)
If the reception method is fax automatic reception, the number of rings until the machine
answers a call can be changed as needed.
NOTE
This setting does not appear in some regions.
Rings(TAD)
If the reception method is FAX/Answering Machine Auto Switch Reception, the number of rings
until the machine answers a call can be changed as needed.
NOTE
This setting does not appear in some regions.
Rings(FAX/TEL)
If the reception method is FAX/TEL Auto Switch Reception, the number of rings until the
machine answers a call can be changed as needed.
NOTE
This setting does not appear in some regions.
Forward Settings
Configure Forward Settings.
Refer to Forward Settings on page 5-2.
RX Settings
Select the reception mode.
Value: Auto(Normal), Auto(FAX/TEL), Auto(TAD), Auto(DRD), Manual
NOTE
DRD reception mode is only available for Australia and New Zealand. This setting
does not appear in other regions.
9-5
Fax Settings > Default fax settings
Item
Description
RX Date/Time
Reception Date/Time function adds the reception date/time, sender information and number of
pages on the top of each page when the message is printed out. It is useful for confirming the
time of reception if the fax is from a different time zone.
Value: On, Off
For details, refer to Reception Date/Time on page 4-6.
Remote SW Dial
To start fax reception by operation from the connected telephone set, use the following operation.
Value: 00 - 99
For details, refer to Remote Switch Function on page 7-9.
Duplex Printing
When received multiple pages of data are the same width, they can be printed out on both
sides of paper having the same width as the data.
Value: On, Off
NOTE
The optional duplex unit is required.
For details, refer to Duplex Print Output on page 4-6.
Unknown Number RX
When Reception Restriction is set, you can set whether or not reception is allowed from parties
that do not provide notification of their fax number.
Value: Reject, Permit
For details, refer to Transmission Restriction on page 9-8.
ECM RX
Set whether ECM RX is performed.
ECM is a communication mode specified by the ITU-T (International Telecommunication Union)
that retransmits data when an error occurs. Fax machines that have ECM mode check for
errors as they communicate, preventing distortion of the image due to noise on the line and
other conditions.
Value: On, Off
NOTE
When there is a large amount of noise on the line, communication may take slightly
longer than when Off is selected.
RX Start Speed
Change the RX Start Speed.
When communication conditions are bad, the fax may not be received correctly. In that case,
set a lower RX Start Speed.
Value: 9600bps, 14400bps, 33600bps
NOTE
Normally this should be used with the default setting.
TX/RX Restriction
This function allows you to send or receive originals only when communication requirements are met.
For details, refer to Transmission Restriction on page 9-8.
Select Key Set. (Select Key Settings)
If you register a function to the Left Select key or Right Select key, you can quickly set the function when using fax
functions.
9-6
Fax Settings > Default fax settings
Item
Left
Description
You can register one of the following functions to each key.
Value: None, Original Size, FAX Resolution, File Name Entry, FAX Delayed TX, FAX Direct TX,
FAX TX Report
Right
NOTE
[FAX TX Report] is displayed when [FAX TX Result] is set to [Specify Each Job].
For details, refer to FAX TX Result Reports on page 8-5.
9-7
Fax Settings > Transmission Restriction
Transmission Restriction
This function allows you to send or receive originals only when communication requirements are met. Using this function
can limit other parties with which you can communicate.
Specifically, you must register communication requirements (Permit FAX No) and set the transmission limit in advance.
When the machine sends or receives originals, you do not need to perform a special operation for this particular
function, and you can operate the machine normally. When sending or receiving has actually started, the machine
correctly conducts transmission that meets communication requirements, but when the transmission does not meet the
requirements, the machine indicates an error. This mode also allows you to set a [Reject List] for Reception Restriction
so that reception from senders on the list of Rejected FAX numbers or from senders whose Local FAX Number is not
registered are rejected. (You can select whether reception from a party whose local fax number is not registered is
allowed or rejected in Unknown Number Reception on page 9-13.)
NOTE
Before using transmission restriction, be sure to read the following prerequisites,
communication establishing requirements, and reception rejection requirements thoroughly,
and consult with the other parties with which you communicate.
Prerequisites
Send
Restrictions
Reception
Restrictions
Communication Establishing
Requirements
• Register Permitted FAX numbers. *1
(Refer to Registering Permit FAX No.
on page 9-9.)
• The recipient’s Local FAX Number
matches a Permitted FAX No.
registered on the machine.
• Send restriction settings are specified
in [Permit+Addr Book] in Send
Restrictions. (Refer to Setting Send
Restriction on page 9-12.)
• Register the Local FAX Numbers of
other parties.
• When the number was dialed using
the Address Book or One-touch keys,
the last 4 digits of the dialed number
match the last 4 digits of the
recipient’s Local FAX Number.
(Excludes manual transmissions.)
• Register Permitted FAX numbers.*2
(Refer to Registering Permit FAX No.
on page 9-9.)
• The sender’s Local FAX Number
matches a Permitted FAX No.
registered on the machine.
• Reception restriction settings are
specified in [Permit+Addr Book] in
Reception Restrictions. (Refer to
Setting Reception Restriction on
page 9-13.)
• A fax number that matches the last 4
digits of the sender’s Local FAX
Number is registered in the Address
Book on this machine.
• Register the Local FAX Numbers of
other parties.
*1 If no Permit FAX number is registered for the recipient, sending is not rejected.
*2 If no Permit FAX number is registered for the sender, reception is not rejected.
Prerequisites
Reception
Rejection
• Register Reject FAX numbers.*1
(Refer to Registering Reject FAX No.
on page 9-10.)
• Reception restriction settings are
specified in [Reject List] in Reception
Restrictions. (Refer to Setting
Reception Restriction on page 9-13.)
9-8
Reception Rejection
Requirements
• The sender’s Local FAX Number is
not registered.
• The sender’s Local Fax Number
matches a Reject FAX No. registered
on the machine.
Fax Settings > Transmission Restriction
*1 If there are no Reject FAX numbers registered, calls are only rejected from senders whose Local
FAX Numbers (Indicates local FAX information entries, not the actual line numbers.) are not registered.
Registering Permit FAX No.
NOTE
Up to 25 Permit FAX numbers can be registered.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Permit No. List].
7 Press the [OK] key.
2
Add a permit fax number.
1 Press [Menu].
2 Press the [▲] or [▼] key to select [Add FAX Number].
3 Press the [OK] key.
4 Use the numeric keys to enter a Permit FAX number.
NOTE
Up to 20 digits can be entered.
5 Press the [OK] key.
3
To register another permit fax number, repeat step 2.
Changing and Deleting Permit FAX No.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
9-9
Fax Settings > Transmission Restriction
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Permit No. List].
7 Press the [OK] key.
2
Change/Delete.
Changing
1 Press the [▲] or [▼] key to select the Permit FAX No. to be changed.
2 Press the [OK] key.
3 Use the numeric keys to reenter the Permit FAX number.
NOTE
For the procedure for entering a number, refer to Registering Permit FAX No. on page 9-9.
4 Press the [OK] key.
Deleting
1 Press the [▲] or [▼] key to select the Permit FAX No. to be deleted.
2 Press [Menu].
3 Press the [▲] or [▼] key to select [Delete].
4 Press the [OK] key.
5 Press [Yes] in confirmation screen.
Registering Reject FAX No.
NOTE
Up to 25 Reject FAX numbers can be registered.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
9-10
Fax Settings > Transmission Restriction
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Reject No. List].
7 Press the [OK] key.
2
Add a Reject FAX No.
1 Press [Menu].
2 Press the [▲] or [▼] key to select [Add FAX Number].
3 Press the [OK] key.
4 Use the numeric keys to enter a Reject FAX number.
NOTE
Up to 20 digits can be entered.
5 Press the [OK] key.
3
To register another Reject FAX No, repeat step 2.
Changing and Deleting Reject FAX No.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Reject No. List].
7 Press the [OK] key.
2
Change/Delete.
Changing
1 Press the [▲] or [▼] key to select the Reject FAX No. to be changed.
2 Press the [OK] key.
9-11
Fax Settings > Transmission Restriction
3 Use the numeric keys to reenter the Reject FAX number.
NOTE
For the procedure for entering a number, refer to Registering Reject FAX No. on page 9-10.
4 Press the [OK] key.
Deleting
1 Press the [▲] or [▼] key to select the Reject FAX No. to be deleted.
2 Press [Menu].
3 Press the [▲] or [▼] key to select [Delete].
4 Press the [OK] key.
5 Press [Yes] in confirmation screen.
Setting Send Restriction
You can restrict the other parties to which you send originals only to the ones registered in Permit FAX No. as well as the
ones registered in the Address Book. To change the sending restriction, follow the steps below.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [TX Restriction].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [Permit+Addr Book] or [Off].
2 Press the [OK] key.
To restrict the other parties only to the ones registered in Permit FAX No. as well as the ones
registered in the Address Book, select [Permit+Addr Book].
9-12
Fax Settings > Transmission Restriction
Setting Reception Restriction
You can restrict incoming faxes so that you only receive originals from senders registered in Permit FAX No. and
senders registered in your Address Book. This mode also allows you to set a [Reject List] for Reception Restriction so
that reception from senders on the list of Rejected FAX numbers or from senders whose Local FAX Number is not
registered are rejected.
(You can select whether reception from a party whose local fax number is not registered is allowed or rejected in
Unknown Number Reception on page 9-13.) To change the reception restriction, follow the steps below.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [RX Restriction].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [Permit+Addr Book], [Reject List] or [Off].
2 Press the [OK] key.
To restrict the other parties only to the ones registered in Permit FAX No. as well as the ones
registered in the Address Book, select [Permit+Addr Book]. To block incoming faxes from
senders registered in Reject FAX No., select [Reject List].
Unknown Number Reception
Select whether to receive the fax of that the number is unknown when [Reject List] is set for Reception Restriction. To
change the reception restriction for the unknown fax number, follow the steps below.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [FAX].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [TX/RX Restrict.].
9-13
Fax Settings > Transmission Restriction
5 Press the [OK] key.
6 Press the [▲] or [▼] key to select [Unknown Number RX].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [Reject] or [Permit].
2 Press the [OK] key.
To receive faxes from the unknown number, select [Permit]. To reject faxes from the unknown
number, select [Reject].
9-14
Fax Settings > Unusable Time
Unusable Time
This feature sets a time period during which the machine will not print received faxes.
IMPORTANT
When Unusable Time is set, in addition to fax printing, all other printing operations are prohibited during the
unusable time period, including printing of copy jobs and printer jobs.
Faxes and print jobs received during the unusable time period are printed after the unusable time period
ends, or when the unusable time period is temporarily canceled.
1
Display the screen.
1 Press the [Status/System Menu/Counter] key.
2 Press the [▲] or [▼] key to select [Common Settings].
3 Press the [OK] key.
4 Press the [▲] or [▼] key to select [Timer Setting].
5 Press the [OK] key.
NOTE
If the login user name entry screen appears during operations, log in by referring to the
machine's Operation Guide for Administrator User Name and Password.
The factory default login user name and login password are set as shown below.
Login User Name
Login Password
Admin*1
Admin*1
*1 Upper case and lower case letters are distinguished (case sensitive).
6 Press the [▲] or [▼] key to select [Unusable Time].
7 Press the [OK] key.
2
Configure the function.
1 Press the [▲] or [▼] key to select [On].
2 Press the [OK] key.
Set the unusable time
1 Press the [▲] or [▼] key to set the hours and minutes of the start time. Press the [◄] and
[►] key to move the cursor right and left.
2 Press the [OK] key.
3 Press the [▲] or [▼] key to set the hours and minutes of the end time. Press the [◄] and
[►] key to move the cursor right and left.
9-15
Fax Settings > Unusable Time
NOTE
If the same time is set as the start time and end time, you cannot use all day.
4 Press the [OK] key.
Set the cancel code
Specify the code to temporarily cancel the unusable setting during unusable time.
1 Use the numeric keys to enter Unlock Code (0000 to 9999)
2 Press the [OK] key.
NOTE
To use the machine temporarily during unusable time, enter the Unlock Code and press
[Login].
Unlock code:
(0000 - 9999)
****
2
Now, the machine is
prohibited to be
used.
1
23:00 㵨 08:30
Code
Exit
9-16
3
Login
Fax Settings > Account Management
Account Management
There is job accounting that controls the usage per account.
In job accounting, the status of fax use per account can be known for up to 30 accounts for sending of originals and
making communication reservation after entering Account ID. For each management method, refer to the machine's
Operation Guide.
Description of Job Accounting
Item
Description
Registration of Account
Register Account Name and Account ID. Up to 8 digits can be entered.
Enable/Disable job
accounting
Enable job accounting.
FAX send restriction
Restricts the number of fax sheets that can be sent. You can prohibit the
use of this sending function or cancel the sending restriction.
Counting of the number of
used sheets
You can reset the counting, referring to the number of fax sheets to be
sent and the time required for sending fax by all the accounts or by
account.
Print of Accounting
Report
You can print the printed and sent page numbers that have been counted
by all the accounts.
NOTE
For details, refer to the machine’s Operation Guide.
Communication modes subject to job accounting
•
Normal transmission
•
Delayed transmission
•
Manual send when dialed from this machine to the receiving system
•
Sending Faxes from PC
Restriction of use function
When you have enabled job accounting, you need to enter an Account ID when performing the
following operations.
•
Normal transmission
•
Delayed transmission
•
Manual send when dialed from this machine to the receiving system
•
Sending Faxes from PC
Normally, the Local FAX Name is printed in the transmit terminal identification (TTI). However,
when job accounting has been enabled, and you send originals after entering an Account ID,
the Account Name is printed.
9-17
Fax Settings > Account Management
Logging in when Job Accounting has been Enabled
When job accounting has been enabled, you need to enter an Account ID when using the machine.
Login
1
Enter the account ID.
Account ID:
Counter
If this screen is displayed during operations, enter the account ID.
NOTE
If you entered a wrong character, press the [Clear] key and enter the account ID again.
If the entered account ID does not match the registered ID, a warning beep will sound and
login will fail. Enter the correct account ID.
By pressing [Counter], you can refer to the number of pages printed and the number of
pages scanned.
2
Log in.
1 Press the [OK] key.
NOTE
When the operation is completed, press the [Logout] key.
9-18
10
Troubleshooting
This chapter explains the following topics:
Indicators During Sending/Receiving Operation .............................................................................................. 10-2
Responding to an Attention Indicator Flashes ................................................................................................. 10-2
Precautions When Turning Power OFF ........................................................................................................... 10-3
Messages ......................................................................................................................................................... 10-4
Error Code List ................................................................................................................................................. 10-5
Troubleshooting ............................................................................................................................................... 10-7
10-1
Troubleshooting > Indicators During Sending/Receiving Operation
Indicators During Sending/Receiving Operation
The [Processing] and [Memory] indicators show the fax transmission status.
•
The [processing] indicator blinks during fax transmission and reception.
•
The [Memory] indicator is lit when there is source data stored in the memory for delayed transmission.
Responding to an Attention Indicator Flashes
If the [Attention] indicator is lit up or blinks, check the message display. If error information is not indicated on the
message display, check the following.
Symptom
Cannot send fax.
Checkpoints
Corrective Actions
Reference
Page
Is the modular cord connected
correctly?
Connect the modular cord correctly.
—
Is Permitted FAX No. registered
correctly?
Check Permitted FAX No.
9-8
Has a communication error
occurred?
Check error codes in the TX/RX Result
Report and Activity Report. If the error
code starts with "U" or "E", perform the
corresponding procedure.
10-5
Is the destination FAX line busy?
Send again.
—
Does the destination FAX
machine respond?
Send again.
—
Is there an error other than
above?
Contact your Service Representative.
—
10-2
Troubleshooting > Precautions When Turning Power OFF
Precautions When Turning Power OFF
To power off the machine, press the Power switch. You cannot automatically receive a fax when the power switch is
turned off.
Make sure that the [Processing] indicator and the [Memory] indicator are off before turning off the power switch.
Check that the indicators
are off.
NOTE
When the [Processing] indicator or [Memory] indicator is lit up, the machine is operating.
Turning off the power switch while the machine is operating may cause it to malfunction.
10-3
Troubleshooting > Messages
Messages
When an error occurs, the display may show one of the messages listed below. These will help you identify and correct
the problem.
NOTE
When a transmission error occurs, a sent/receipt result report is produced.
Check the error code shown in the report and refer to Error Code List on page 10-5 for a description. To print the sent/
receipt result report, refer to FAX TX Result Reports on page 8-5 and FAX RX Result Reports on page 8-6.
You may also check error codes using the activity report. (Refer to Activity Report on page 8-7.)
Message
Error occurred.
Checkpoint
Corrective Action
Reference
Page
―
System error has occurred. Turn the
power switch OFF and then ON.
―
FAX memory is full.
―
FAX cannot be performed any more due
to insufficient memory of scanner. The job
is canceled. Press the [OK] key.
―
Insufficient memory.
―
Job cannot be started. Try again later.
―
Is the acceptable printing count
restricted by Job Accounting
exceeded?
The printing count exceeded the
acceptable count restricted by Job
Accounting. Cannot print any more. This
job is canceled. Press the [OK] key.
Refer to the
machine’s
Operation
Guide.
Is the indicated cassette out of
paper?
Load paper.
Select [Paper] to select the other paper
source. Press the [OK] key to print on the
paper in the currently selected paper
source.
―
―
An error has occurred in the machine.
Make a note of the error code displayed
on the message display, and contact your
service representative.
―
―
Scanning cannot be performed any more
due to insufficient memory of scanner.
Press the [OK] key to cancel the job.
―
―
This job is canceled because it is
restricted by User Authorization or Job
Accounting. Press the [OK] key.
Refer to the
machine’s
Operation
Guide.
―
Scanning cannot be performed any more
due to insufficient memory of scanner.
The job is canceled. Press the [OK] key.
―
―
The number of jobs has exceeded the
limit set for delayed transmission. Press
the [OK] key. The job is canceled.
3-17
―
Put down the receiver.
―
Turn the power
switch off and on.
Cannot start the job.
Job Accounting
restriction exceeded.
Job is canceled.
Load paper in
cassette 1.
Press OK to continue
using cassette 1.
Machine failure.
Call service.
Maximum Number of
scanned pages.
Job is canceled.
Restricted by
Job Accounting.
Cannot print.
Scanner memory
is full.
Job is canceled.
Scheduled sending
jobs exceeded.
The phone receiver is
off the hook.
Hang Up.
10-4
Troubleshooting > Error Code List
Error Code List
When a transmission error occurs, one of the following error codes is recorded in the TX/RX Result Report and Activity
Report.
NOTE
“U” or “E” will appear in the error code depending on the communication speed setting.
Error Code
Possible Cause/Action
Busy
Failed to establish connection with the recipient despite auto redialing the preset number of times.
Send again.
CANCELED
Transmission was canceled due to an action to cancel transmission.
Reception was canceled due to an action to cancel reception.
U00300
Paper depletion occurred at the recipient machine. Check with the recipient.
U00430 - U00462
Reception was canceled because of mismatching of communication features with the sender machine
although the line connection was established.
U00601 - U00690
Communication was stopped due to the machine failure. Send or receive again.
U00700
Communication was stopped due to failure on the part of the sender or recipient machine.
U00800 - U00811
Page(s) not sent correctly. Send again.
If you still have trouble, reduce TX Start Speed and send again.
NOTE
If the communication error occurs frequently, change the default setting of TX Start Speed in
System Menu.
U00900 - U00910
Page(s) not received correctly. Ask the sender to resend.
NOTE
If the communication error occurs frequently, change the default setting of RX Start Speed in
System Menu.
U01000 - U01097
Communication error occurred during transmission. Send again.
If you still have trouble, reduce TX Start Speed and send again.
NOTE
If the communication error occurs frequently, change the default setting of TX Start Speed in
System Menu.
U01100 - U01196
Communication error occurred during reception. Ask the sender to resend.
NOTE
If the communication error occurs frequently, change the default setting of RX Start Speed in
System Menu.
U01400
Failed to establish communication with the sender or recipient machine because dialing registered for
a tone line system was used in a pulse line system.
U01500
Communication error occurred during high-speed transmission. Send again.
If you still have trouble, reduce TX Start Speed and send again.
NOTE
If the communication error occurs frequently, change the default setting of TX Start Speed in
System Menu.
10-5
Troubleshooting > Error Code List
Error Code
U01600
Possible Cause/Action
Communication error occurred during reception of high-speed transmission. Ask the sender to reduce
the transmission speed and send again.
NOTE
If the communication error occurs frequently, change the default setting of RX Start Speed in
System Menu.
U01700 - U01720
Communication error occurred during high-speed transmission. Send again.
If you still have trouble, reduce TX Start Speed and send again.
NOTE
If the communication error occurs frequently, change the default setting of TX Start Speed in
System Menu.
U01721
Communication error occurred during high-speed transmission. Designated transmission speed may
not be available for the recipient machine.
Reduce the transmission start speed and send again.
U01800 - U01820
Communication error occurred during reception of high-speed transmission. Ask the sender to reduce
the transmission speed and send again or reduce the RX Start Speed in System Menu.
U01821
Communication error occurred during reception of high-speed transmission. Designated transmission
speed may not be available for this machine. Ask the sender to reduce the transmission speed and
send again or reduce the RX Start Speed in System Menu.
U05100
Transmission was canceled because communication requirements are not met due to the
transmission restriction set on this machine. Check with the recipient.
U05200
Reception was canceled because communication requirements are not met due to the reception
restriction set on this machine.
U05300
Reception was rejected by the recipient because communication requirements are not met due to the
reception restriction set on the recipient machine. Check with the recipient.
U19000
Memory reception was stopped because there is no more free space in the memory of this machine.
Create free space by outputting the data stored in the memory, and ask the sender to resend.
U19100
Transmission was stopped because there is no more free space in the memory of the recipient
machine. Check with the recipient.
10-6
Troubleshooting > Troubleshooting
Troubleshooting
When a problem occurs, first check the following. If the problem persists, contact your dealer or service representative.
Symptom
Cannot send document.
Checkpoint
Corrective Action
Reference
Page
Is the modular cord connected
correctly?
Connect the modular cord correctly.
―
Is Send error displayed?
Remedy the cause of error and send
again.
10-5
Is TX (transmission) restriction
activated?
Cancel the TX restriction.
9-8
Is a pulse line used?
Some phones may transmit tone signals
using buttons. Refer to the operation
manual of your phone set.
―
Is the remote switching number
correct?
Check the registration. (Default: 55)
7-9
No print output after reception.
Is memory forwarding activated?
Check the forwarding destination.
5-2
Cannot receive document.
Is the modular cord connected
correctly?
Connect the modular cord correctly.
―
Is Communication error
displayed?
Remedy the cause of error and ask the
sender to retry.
10-5
Is RX (reception) restriction
activated?
Cancel the RX restriction.
9-8
Cannot perform memory
reception.
Is free space available in the
memory?
Receive after the memory has free space,
or create free space in the memory.
―
Cannot perform memory
forwarding.
Is memory forwarding set to
[On]?
Check the memory forwarding setting.
5-2
Cannot use the remote
switching function.
10-7
11
Appendix
This chapter explains the following topics:
Character Entry Method .................................................................................................................................... 11-2
Specifications .................................................................................................................................................... 11-6
Menu Map ......................................................................................................................................................... 11-8
Received FAX Sizes and Paper Priority (Metric Model) .................................................................................. 11-11
Received FAX Sizes and Paper Priority (Inch Model) ..................................................................................... 11-12
11-1
Appendix > Character Entry Method
Character Entry Method
This section explains how to enter characters.
Using the Keys
1
4
6
3
2
5
Account Name:
7
ABC
Text
No.
Display/Key
Description
1
Message Display
Displays entered characters.
2
[Clear] key
Press to delete characters.
3
Numeric keys
Press to enter characters and symbols.
4
Arrow keys
Press to select the entry position, or select a character from the character list.
5
[OK] key
Press to finalize entry and return to the screen before the entry. To enter a symbol, press to confirm the
selected symbol.
6
Right Select key
Press to select the type of characters you want to enter. (When [Text] is displayed)
7
Cursor
Characters are entered at the position of the cursor.
11-2
Appendix > Character Entry Method
Selecting Type of Characters
To enter characters, the following three types are available:
Types
Description
ABC
To enter alphabets.
123
To enter numerals.
Symbols
To enter symbols.
In a character entry screen, press [Text] to select the type of characters you want to enter.
Account Name:
Account Name:
ABC
Text
Symbols:
!"#$%&'()*+,-./:;<=>
?@[\]^_`{|}~€£¤¥§
123
Text
Text
Each time you press [Text], the character type switches as follows: [ABC], [123], [Symbols], [ABC] ...
Characters That Can be Entered Using the Numeric Keys
The following table lists the characters that can be entered using the numeric keys.
Keys
Characters (Each press of a key changes the character in the order from left to right.)
.
@
-
_
/
:
~
1
(Repeats from the first character on the left)
B
C
2
(Repeats from the first character on the left)
F
3
(Repeats from the first character on the left)
I
4
(Repeats from the first character on the left)
L
5
(Repeats from the first character on the left)
O
6
(Repeats from the first character on the left)
Q
R
V
8
1 (During number entry)
a
b
c
A
2 (During number entry)
d
e
f
D
E
3 (During number entry)
g
h
i
G
H
4 (During number entry)
j
k
l
J
K
5 (During number entry)
m
n
o
M
N
6 (During number entry)
p
q
r
s
P
S
7
(Repeats from the first character on the left)
7 (During number entry)
t
u
v
T
U
(Repeats from the first character on the left)
8 (During number entry)
11-3
Appendix > Character Entry Method
Keys
Characters (Each press of a key changes the character in the order from left to right.)
w
x
y
z
W
X
Y
Z
9
!
?
(space)
(Repeats from the first character on the left)
9 (During number entry)
.
,
-
_
‘
0
(Repeats from the first character on the left)
0 (During number entry)
Press to change the character in the cursor position between upper case and lower case.
“*” or “.” (During number entry)
!
"
#
$
%
&
'
(
)
*
+
,
-
.
/
<
=
>
?
@
[
\
]
^
_
`
{
|
}
~
# (During number entry)
*
:
;
Displays the
symbol list. For
details, refer to
Entering Symbols
on page 11-4.
Depending on the functions, there are symbols that cannot be entered.
Entering Symbols
Symbols can be entered.
1 Press the [#] key. Displays the symbol list.
Symbols:
!"#$%&'()*+,-./:;<=>
?@[\]^_`{|}~€£¤¥§
Text
2 Press the [▲], [▼], [►] or [◄] key to move the cursor and select the symbol to be entered.
Symbols:
!"#$%&'()*+,-./:;<=>
?@[\]^_`{|}~€£¤¥§
Text
3 Press the [OK] key. The selected symbol is entered.
Account Name:
R&
ABC
Text
Entering Characters
Follow the steps shown below to enter “R&D” for example.
1 Press the [7] key three times. [r] is entered.
Account Name:
r
ABC
Text
11-4
Appendix > Character Entry Method
2 Press the [*/.] key. [r] changes to [R].
Account Name:
R
ABC
Text
3 Press the [►] key. The cursor moves to the right.
Account Name:
R
ABC
Text
4 Press the [#] key. Displays the symbol list.
Symbols:
!"#$%&'()*+,-./:;<=>
?@[\]^_`{|}~€£¤¥§
Text
5 Press the [▲] or [▼] key to move the cursor and select [&].
Symbols:
!"#$%&'()*+,-./:;<=>
?@[\]^_`{|}~€£¤¥§
Text
6 Press the [OK] key. [&] is entered.
Account Name:
R&
ABC
Text
7 Press the [3] key four times. [D] is entered.
Account Name:
R&D
ABC
Text
8 Press the [►] key.
Account Name:
R&D
ABC
Text
11-5
Appendix > Specifications
Specifications
NOTE
Specifications are subject to change without notice.
FAX function
Item
Description
Type
Optional FAX kit
Compatibility
SuperG3
Communication Line
Subscriber telephone line
Transmission Time
4 seconds or less (MMR, ITU-T A4 #1 chart)
Transmission Speed
33600/31200/28800/26400/24000/21600/19200/16800/14400/12000/
9600/7200/4800/2400 bps
Coding Scheme
MMR/MR/MH
Error Correction
ECM
Original Size
Max. width: 297/11" mm, Max. length: 432/17" mm
Automatic Document Feed
Max. 50 sheets (with document processor)
Resolution
Scan:
Horizontal × Vertical
200 × 100 dpi Normal (8 dot/mm × 3.85 line/mm)
200 × 200 dpi Fine (8 dot/mm × 7.7 line/mm)
200 × 400 dpi Super Fine (8 dot/mm × 15.4 line/mm)
Print:
600 × 600 dpi
Gradations
256 shades (Error diffusion)
One-Touch Key
32 keys
Multi-Station Transmission
Max. 100 destinations
Substitute Memory Reception
250 sheets or more (when using ITU-T A4 #1)
Image Memory Capacity
4 MB (standard)
Report Output
FAX TX result report, FAX RX result report, Activity report, Status page
11-6
Appendix > Specifications
FAX Driver functions
Item
Description
Hardware
IBM PC-AT compatible computer
Interface
10BASE-T, 100BASE-TX or USB
Operating system
Windows XP or higher
Transmission Resolution
Fine (200 × 200dpi), Normal (100 × 200dpi)
Document Size
Ledger(11 × 17"), Letter, Legal, Statement, A3, B4, A4, A5, Folio,
B5(JIS)
FAX Delayed Transmit
Based on settings in the FAX Driver (setting is possible to any 1
minute increment within the subsequent 24 hour period)
Transmit and Print
Fax transmission and print out at the machine is available
Broadcast Transmission
Up to 100 destinations
Job Accounting
Requires the input of an Account ID in the FAX Driver when Job
Accounting, is turned ON in the fax machine.
Cover Page
A format can be selected using the FAX Driver or a template can
be created.
11-7
Appendix > Menu Map
Menu Map
Density (page 3-14)
Original Image (page 3-14)
2-sided Original (page 3-14)
Program (page 3-19)
Address Book (page 3-4)
Redial (page 3-9)
Checking and Editing Destinations (page 3-7)
Manual Send (page 3-15)
Manual Reception (page 4-4)
One Touch Key (page 3-6)
Original Size (page 3-16)
FAX Resolution (page 3-16)
File Name Entry (page 3-16)
FAX Delayed TX (page 3-17)
FAX Direct TX (page 3-17)
FAX TX Report (page 3-18)
11-8
Appendix > Menu Map
Status
Print Job Status (refer to the machine’s Operation Guide)
Send Job Status (refer to the machine’s Operation Guide)
Scheduled Job (page 3-18)
Print Job Log (page 8-3)
Send Job Log (page 8-3)
Scanner (refer to the machine’s Operation Guide)
Printer (refer to the machine’s Operation Guide)
FAX
Log
Outgoing FAX Log (page 8-4)
Incoming FAX Log (page 8-4)
Outgoing FAX Rpt (page 8-7)
Incoming FAX Rpt (page 8-7)
Toner Status (refer to the machine’s Operation Guide)
Paper Status (refer to the machine’s Operation Guide)
Report (page 9-3)
Report Print (page 9-3)
Menu Map (refer to the machine’s Operation Guide)
Status Page (page 8-9)
Network Status (refer to the machine’s Operation Guide)
Service Status (refer to the machine’s Operation Guide)
Admin Rpt Set. (page 87)
Outgoing FAX Rpt (page 8-7)
Result Rpt Set.
FAX TX Result (page 8-5)
Incoming FAX Rpt (page 8-7)
FAX RX Result (page 8-6)
Counter (refer to the machine’s Operation Guide)
System (refer to the machine’s Operation Guide)
Admin/Accounting (refer to the machine’s Operation Guide)
Common Settings
Default Screen (refer to the machine’s Operation Guide)
Sound (page 9-3)
FAX Speaker Volume (page 9-3)
FAX Monitor Volume (page 9-3)
Orig./Paper Set. (refer to the machine’s Operation Guide)
Date Setting (page 1-6)
Timer Setting
Unusable Time (page 9-15)
Function Default
FAX Resolution (page 9-4)
Copy (refer to the machine’s Operation Guide)
Send (refer to the machine’s Operation Guide)
11-9
Appendix > Menu Map
FAX (page 9-4)
Transmission
(page 9-4)
TTI (page 1-8)
Local FAX Name (page 1-8)
Local FAX Number (page 1-9)
FAX Dialing Mode (page 1-10)
Retry Times (page 9-4)
ECM TX (page 1-11)
TX Start Speed (page 1-11)
Reception (page 9-5)
FAX Media Type (page 9-5)
Rings(Normal) (page 9-5)
Rings(TAD) (page 9-5)
Rings(FAX/TEL) (page 9-5)
Forword Settings (page 5-2)
RX Setting (page 9-5)
RX Date/Time (page 9-5)
Remote SW Dial (page 9-5)
Duplex Printing (page 9-5)
ECM RX (page 9-5)
RX Start Speed (page 9-5)
TX/RX Restrict. (page 9-8)
Select Key Set. (page 9-6)
Edit Destination
Address Book (page 2-2)
Print List (page 2-11)
Adjust/Maint. (refer to the machine’s Operation Guide)
11-10
Appendix > Received FAX Sizes and Paper Priority (Metric Model)
Received FAX Sizes and Paper Priority (Metric Model)
When no paper loaded in the cassettes matches the received fax size and orientation, the machine automatically
chooses the printing paper according to the following priority.
Same Size Override
Received FAX Size
A5
B5
A4-R
A4
Folio
B4
A3
B5
A4-R
A4
Folio
B4
A4
A4-R
A4-R
A4-R
1
A5-R
Folio
B4
A3
Long
Originals
Long
Originals
Long
Originals
Long
Originals
A3
A3
A3
A3
A3
A3
A4
A3
A3
A3
A4
B5
A4-R
B4
B4
B4
A4-R
B4
B4
B5
Folio
A4-R
Folio
B5-R
A4
A4-R
A4
Priority
*1
2
3
A4R
B5-R
*1
Folio
B4
*1
Folio
*1
Folio
*1
*2
A4
*1,
*1
*1
*2
4
A4
5
B5
Paper Size
6
7
*1
A4-R
*1
B5-R
*1
A3
A4
Folio
A3
*1
A3
A3
B4
B4
A5-R
*1
B5
*3
*1
A3
B5-R
Folio
B4
A4
B4
*1
*3
A4-R
A4
*1
A4
B4
A4-R
*1,
*1
*1,
*1
*1
*1
*1
*3
A5-R
A4-R
A4-R
B5
A4
Folio
*1
B4
*1
*1
*3
8
B4
B5
A5-R
*1
A4-R
*1
*1,
*1
*3
9
B5-R
*1,
B5
Folio
*3
10
B5-R
*1
*1,
B5-R
*1
A4
*1
*3
B5-R
*1
Folio
*1
A5-R
*1
11
B5
12
B5-R
*1
*1 Paper orientation is different from the received document. The image is printed after being rotated
90°automatically.
*2 Received Folio size document is reduced to match A4 size paper.
*3 If the lengths of the received originals are short, the received originals may be printed with this paper
size.
: indicates print output on two sheets.
NOTE
When a paper type is selected in Media Type for Print Output, a received fax is printed using the matching paper
source. (Refer to page 4-6.)
If [All Media Types] is selected, a paper type cannot be specified for fax printouts.
11-11
Appendix > Received FAX Sizes and Paper Priority (Inch Model)
Received FAX Sizes and Paper Priority (Inch Model)
When no paper loaded in the cassettes matches the received fax size and orientation, the machine automatically
chooses the printing paper according to the following priority.
Same Size Override
Received FAX Size
Statement
Letter-R
Letter
Legal
Ledger
1
Statement-R
Letter-R
Letter
Legal
Letter
Letter-R
Letter-R
Letter-R
Legal
Ledger
Long Originals
Long Originals
Long Originals
Ledger
Ledger
Legal
Ledger
Letter
Ledger
Ledger
Letter
Letter-R
Letter-R
Ledger
Letter-R
Legal
Letter
Letter-R
Legal
Priority
*1
2
3
Letter-R
Legal
*1
Legal
*1
Legal
*1
*2
Letter
*1,
*1
*1
*2
Paper Size
4
5
6
Letter
*1
Ledger
Ledger
Statement-R
*1
Ledger
Ledger
Letter-R
*1
*1
Statement
Letter
*1
*1
*3
*1
Letter-R
Letter
*1,
*3
7
Statement-R
*1
8
Letter
*1
Statement-R
*1
*1 Paper orientation is different from the received document. The image is printed after being rotated
90°automatically.
*2 Received Legal size document is reduced to match Letter size paper.
*3 If the lengths of the received originals are short, the received originals may be printed with this paper
size.
: indicates print output on two sheets.
NOTE
When a paper type is selected in Media Type for Print Output, a received fax is printed using the matching paper
source. (Refer to page 4-6.)
If [All Media Types] is selected, a paper type cannot be specified for fax printouts.
11-12
Index
L
Local FAX Name 9-4
Local FAX Number 9-4
A
M
Account Management 9-17
Address Book 2-2, 3-10
Adding a contact 2-2
Adding a Group 2-6
Change/Deletion 2-9
Printing Address List 2-11
Search 3-11
Select a Destination 3-10
Machine (Names) 1-2
Manual Reception 4-4, 7-7
Manual Send 3-15, 7-6
Media Type for Print Output 4-6
Memory Reception 4-3
Memory Transmission 3-2
Cancel 3-7
Menu Map 11-8
Messages 10-4
C
Cancel
Cancelling Direct Transmission 3-17
Cancelling Memory Transmission 3-7
Cannot receive document 10-7
Cannot send document 10-7
Character Entry Method 11-2
N
No Print Output 10-7
O
One-touch Keys 2-12
Adding a Destination 2-12
Change/Delete 2-13
Select Destination 3-12
Operation Panel 1-4
Original
2-sided Original 3-14
Original Size 3-16
Original Image 3-14
D
Date 1-6
Default fax settings 9-2
Density 3-14
Direct Transmission
Cancel 3-17
Document Processor 1-3
Duplex Print Output 4-6
P
E
Part Names and Functions 1-2
Permit Fax No.
Change/Deletion 9-9
Registration 9-9
Precautions When Turning Power OFF 10-3
ECM RX 9-6
ECM TX 9-5
Error Code List 10-5
F
R
FAX Delayed Transmission 3-17
FAX Direct Transmission 3-17
FAX Driver
Basic Transmission 6-6
Installing the FAX Driver 6-3
Setup 6-3
FAX Job History 8-3
Job Log Screen 8-3, 8-4
FAX TX Resolution 3-16
File Name Entry 3-16
Forward Settings 5-2
I
Indicators 10-2
J
Job Accounting 9-17
Communication Form Subject to Job Accounting 917
Contents 9-17
Limit 9-17
Login 9-18
Received FAX Sizes and Paper Priority 11-11, 11-12
Receiving Mode 4-2, 9-5
Reception Date/Time 4-6
Redial 3-8
Changing Retry Times 9-4
Reject Fax No.
Change/Deletion 9-11
Registration 9-10
Remote Switch Function 7-9, 9-6
How to Register 9-6
How to Use 7-9
Report
Activity Report 8-7
FAX RX Result Reports 8-6
FAX TX Result Reports 8-5
Rings
Answering Machine 9-5
FAX/TEL 9-5
Normal 9-5
RX Start Speed 9-6
Index-1
S
Selection of Transmit Terminal Identification (TTI) 9-4
Send Status 3-6
Specifications 11-6
T
Telephone Line 9-4
Time 1-6
Transmission Restriction 9-8
Communication Establishing Requirements 9-8
Permit FAX No. 9-9
Prerequisites 9-8
Reception Rejection Requirements 9-8
Reception Restriction Setting 9-13
Reject FAX No. 9-10
Send Restriction Setting 9-12
Unknown Number Reception 9-13
Troubleshooting 10-7
TX Start Speed 9-5
U
Unusable Time 9-15
V
Verious Reports for FAX 8-2
Volume Adjustment
FAX Monitor Volume 9-3
FAX Speaker Volume 9-3
Index-2
Index-3
Rev.2 2014.2
3PAKDEN002
Download PDF
Similar pages