kgnfhdledh32va user manual

KGNFHDLEDH32VA
USER MANUAL
Contents
Content
Safety Warnings
2
WELCOME.............................................................. 2
IMPORTANT INFORMATION................................. 2
About your LED LCD TV
5
INSTALLING THE STAND....................................... 5
Install you TV on the wall.....................................6
GET TO KNOW YOUR TV........................................ 7
Front control panel................................................................ 7
Rear Terminals Control ....................................................... 7
GET TO KNOW YOUR REMOTE CONTROL............ 8
CONNECTING YOUR TV......................................... 9
ANTENNA CONNECTION..................................................... 9
IMPROVE YOUR SIGNAL....................................................... 9
CONNECT YOUR PC TO THE TV.......................................... 9
CONNECT A DVD PLAYER TO YOUR TV........................... 9
CONNECT A DVD PLAYER OR VCR TO YOUR TV........... 9
SCART INPUT............................................................................ 9
HDMI INPUT.............................................................................. 9
MOUNT YOUR TV ONTO THE WALL.................................. 9
PREPARATION OF YOUR REMOTE CONTROL.........
BATTERY INSTALLATION.....................................................10
BATTERY CAUTION...............................................................10
Getting Started
10
SETTING UP......................................................... 10
LOCATION...............................................................................10
CONNECTION.........................................................................12
SWITCHING YOUR TV ON...................................................12
TUNING YOUR TV................................................ 12
SWITCHING TO AN EXTERNAL SOURCE OTHER THAN
THE TV......................................................................................12
AUTO SEARCH........................................................................12
DIGITAL MANUAL SEARCH................................................12
Analog Manual Search.......................................................12
Channel Edit...........................................................................13
RENAME...................................................................................13
MOVE........................................................................................13
Setting favourite channel..................................................13
SKIP............................................................................................13
GUIDE (Electronic Program Guide)................................13
COMMON INTERFACE......................................... 14
Software Update function................................................14
EN-1 Digital LED LCD Television Instruction Manual
Operation................................................................................15
USING YOUR TV................................................... 15
How to select the TV program.........................................15
HOW to adjust volume.......................................................15
CH.LIST function...................................................................16
ADJUSTING PICTURE SETTINGS........................ 16
Changing the Picture Setting..........................................16
ADJUSTING SOUND SETTINGS.......................... 16
Changing the Sound Setting...........................................16
FUNCTION SETTINGS.......................................... 17
TIME SETTINGS................................................... 19
LOCK MENU SETTING......................................... 20
SHORTCUT MENU DISPLAY................................ 21
Using the features............................. 23
TELETEXT FUNCTIONS........................................ 23
Teletext....................................................................................23
USB MODE........................................................... 24
TO USE THE USB DEVICE....................................................24
When connecting/removing the USB device............24
Operating the USB device.................................................25
Playing a Picture...................................................................25
Playing Music.........................................................................25
Playing a Movie.....................................................................26
Text............................................................................................26
USING EXTERNAL USBDEVICE FOR RECORDING.26
TIME SHIFT..............................................................................27
RECORDING............................................................................28
Reference Sections
29
TROUBLESHOOTING........................................... 29
SPECIFICATION................................................... 30
Safety Warnings
Safety Warnings
WELCOME
Thanks for buying this FHD Digital LED LCD TV. This manual will help you set up and begin using your TV.
First, check the contents of your box with the parts checklist below:
• FHD Digital LED LCD TV
• Remote control
• AAA battery x 2
• Instruction Manual
• Quick Start Guide
• Warranty Card
• TV Stand
• 5 x Screws for TV stand
• Component adapter, Component audio adapter, SCART adapter
• Cover. Used when wall mounting the TV.
Now you can get started!
IMPORTANT INFORMATION
READ ALL INSTRUCTIONS BEFORE USE AND KEEP FOR FUTURE REFERENCE.
8"3/*/(
3*4,0'&-&$53*$4)0$,
%0/0501&/
8"3/*/(
503&%6$&5)&3*4,0'&-&$53*$4)0$,%0/053&.07&$07&303#"$,
/0
64&34&37*$&"#-&1"354*/4*%&3&'&35026"-*'*&%4&37*$&1&340//&-
5PBWPJEFMFDUSJDIB[BSETJUJTTUSPOHMZTVHHFTUFEUIBUUIFCBDLDPWFSOPUCFPQFOFEBT
UIFSFBSFOPBDDFTTPSJFTJOTJEFUIFDBTJOH
*G OFDFTTBSZ QMFBTF DPOUBDU BVUIPSJ[FE BGUFSTBMFT TFSWJDFT
DPVMESFTVMUJOTFSJPVTJOKVSZCZIJHIWPMUBHF
"O FYDMBNBUJPO NBSL JO B USJBOHMF .BKPS QBSU PS BDDFTTPSZ PG XIJDI UFDIOJDBM
NVTU CF GPMMPXFE J F IU JT UP CF SFQMBDFE
WARNING: To avoid fire or electric hazards, never place your television receiver in an area with heavy
moisture. Attention should be paid to avoid accidental scratches or impacts onto the screen.
CAUTION: ▲ Please read this manual carefully before using your television and keep this manual in a
good place for future reference.
▲ To achieve the best performance of your television, read this User‘s Manual carefully and
properly store it for future reference.
▲ Information of screen displays and figures in the User’s Manual may vary due to technical
innovations.
CAUTION: ▲ Unauthorized disassembly of this product is prohibited.
TruSurround XT, SRS and the
symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is
incorporated under license from SRS Labs, Inc.
TruSurround XT® creates a truly immersive surround sound experience with rich bass and clear dialog from only
two speakers.
WARNING To prevent the spread of fire,keep candles or other open flames away from this product at all
times.
Digital LED LCD Television Instruction Manual EN-2
Safety Warningss
If fixing TV to the wall please make sure
unit is securely fixed.
or close to any
heat sources.
al
EN-3 Digital LED LCD Television Instruction Manual
Safety Warnings
Do not
Do not
kept
Always make sure the TV is securely plugged
in, as a poor electrical connection may cause
a fire.
Unplug the TV, if you are going to clean the
product, use soft fabric, never chemicals,
make sure that no water
drops are in the product.
Digital LED LCD Television Instruction Manual EN-4
About your LED LCD TV
About your LED LCD TV
INSTALLING THE STAND
1.Carefully place the TV screen face down on a table. We suggest that you place the
wrapping material from the TV package on the table top to protect the screen from
damage.
2.Position the stand with the bottom of the TV as shown below.
.
3.Push the stand onto the TV。
4.Attach the screws from the bottom of the stand to the TV.
EN-5 Digital LED LCD Television Instruction Manual
About your LED LCD TV
Installing your TV on the wall
1.
Carefully place the TV screen face down on a soft surface or table covered in a cloth. We suggest that you place the
wrapping material from the TV package on the table top to protect the screen from damage.
2.
Position the cover over the stand aperture and secure with the (5) cross head screws supplied.
3.
32" FHD Digital LED LCD TV
Attach the wall mounting bracket (not supplied) to the back of the TV using 4 x 4mm screws (not supplied).
Fit the TV to the wall referring to the wall mounting manufactures instructions.
WARNING:Take secure when fitting the TV to the wall TV is heavy.
3.
40" FHD Digital LED LCD TV
Remove the (4) blanking screws from the TV.
4 X wallmounting points
4.
Attach the wall mounting bracket (not supplied) to the back of the TV using 4 x 6mm screws (the screws supplied with
the TV may not be long enough, select suitable screws to securely fit the wall mounting). Fit the TV to the wall referring
to the wall mounting manufactures instructions.
WARNING:Take secure when fitting the TV to the wall TV is heavy.
Digital LED LCD Television Instruction Manual EN-6
About your LED LCD TV
GET TO KNOW YOUR TV
Front control panel
SOURCE
MENU
VOL
CH
To use the touch sensor on the side of the TV.
1 SOURCE
2 MENU
3 VOL-/+
Touch to toggle between all the available
input sources. Use with the CH 5 and
VOL+ buttons to make selections.
Touch to see an on-screen menu of your TV’s
features.
Touch to increase or decrease the volume.
Note: When Source is selected touch VOL + to
confirm selection.
4 CH5
5
Touch to change channels.
Note: Touch to move the on-screen selection up
or down when Source is selected.
Touch to turn the TV On and again to Standby.
Rear Terminals Control
1
2
3
4
5
6
7
SCART
Component
Component Audio
PC
PC/DVI AUDIO
HDMI3 IN
HDMI2 IN
Pr
L
R
AUDIO
Input
Input
Input
Output
Input
Input
Input
EN-7 Digital LED LCD Television Instruction Manual
PC
PC/DVI AUDIO
PC IN
8
9
0
A
B
C
HDMI 3 IN
HDMI 2 IN
Common Interface
Earphone
ANTENNA
Optical
USB
HDMI1 IN
USB
Pb
COMPONENT IN
HDMI 1 IN
Y
SCART
DIGITAL AUDIO OUT
(OPTICAL )
ANT IN
Output
Input
Output
Input / Output
Input
About your LED LCD TV
GET TO KNOW YOUR REMOTE CONTROL
When using the remote control, aim it towards the remote sensor on the TV.
Note ❏❏ RED button, GREEN button, BLUE
button and YELLOW button are fast
text button in analog signal. Function
button in DVBT (just reference the
OSD)
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
`
POWER
DVD Menu / REC
DVD open / close
Picture Mode
Sound Mode
Call Screen Display
Sleep button
DTV Audio / NICAM / DVD Audio
Aspect Ratio Control button
Channel list button
Subtitle button
Program Number Channel selection
Source Exchange
Q.VIEW / Swap Channel
V+/V-: Volume selection
P+/P-: Channel selection
Mute
Menu button
GUIDE button (only for DTV)
Favourite list button
OK button
Cursor Mover button
Back button (only for USB)
Exit Screen Display
REPEAT (only for DVD & USB )/CANCEL button
Zoom (only for DVD & USB)/Teletext index (only for TV) / REC index
Play / Pause button (only for DVD & USB) / Timeshift
Stop (only for DVD, USB, REC & Timeshift)
Fast Reverse (only for DVD, USB, REC & Timeshift)
Fast Forward (only for DVD, USB, REC & Timeshift)
Previous (only for DVD, USB, REC & Timeshift)
Next (only for DVD, USB, REC & Timeshift)
DVD Set up / Text
DVD Title / Teletext Mix
DVD Search / Teletext Subcode
DVD 10+ / Teletext Hold
DVD Program / Teletext Reveal
DVD A-B Repeat / Teletext Size
DVD Call / Teletext Mode
DVD Angle/Teletext Time
Digital LED LCD Television Instruction Manual EN-8
About your LED LCD TV
CONNECTING YOUR
TV
ANTENNA CONNECTION
Connect your aerial to the back of the TV into the
ANTENNA IN socket.
adapter to the COMPONENT (Y, Pb, Pr) IN socket on your
TV.
ATurn on the DVD player and insert a DVD.
BPress the source buttom on the remote control
to
select the source of COMPONENT in your TV .
CRefer to the DVD player user guide for operating
instructions.
IMPROVE YOUR SIGNAL
To improve picture quality in a poor signal area, use a
signal amplifier (not supplied).
DVD
CONNECT YOUR PC TO THE TV
You can use your TV as a monitor for your personal
computer by connecting it with a VGA cable (not
supplied).
ARead your computer user guide and check it has a
VGA connector.
BTurn the power off on your TV and PC.
CConnect a D type 15-pin VGA interface cable to the
VGA video interface connector on the PC. Connect
the other end of the cable to the PC interface
connector on the TV. Tighten the screws on the
VGA connectors and connect the audio cable (not
supplied) to the audio input socket on the back of
the TV.
DTurn on the power of the TV firstly and then the PC.
EPress the button on the TV or TV remote control to
set the video input mode to VGA.
SCART INPUT
AConnect the scart lead from the external device
(DVD player, Set-top box or games console) with the
supplied SCART adapter to the TV scart socket.
BPress the SOURCE button to select SCART mode.
CPress the PLAY button on the external device.
HDMI INPUT
AConnect the cable from the HDMI device to the TV
HDMI socket.
BPress the SOURCE button to select HDMI mode.
CRefer to the HDMI device user guide for how to
operate.
FOnce the image shows, if there is noise present,
change the VGA mode to another resolution,
change the refresh rate to another rate or adjust
the brightness and contrast on the menu until the
picture is clear.
CONNECT A DVD PLAYER TO YOUR
TV
Connect the DVD video outputs (Y, Pb, Pr) with the
supplied component adapter and component audio
EN-9 Digital LED LCD Television Instruction Manual
MOUNT YOUR TV ONTO THE WALL
You can mount your TV onto the wall by using a wall
bracket (not supplied). Use M4/M6 machine screws (4
pcs) to screw the TV onto the bracket (not supplied).
About your LED LCD TV / Getting Started
About your LED LCD TV
PREPARATION OF
BATTERY CAUTION
YOUR REMOTE
Confirm there is no object between the remote control
and the remote sensor of the TV set.
CONTROL
Sunshine or other strong light will interfere with the
signal sent by the remote control. In this situation turn
the TV set to avoid the direct light source.
BATTERY INSTALLATION
Do not put the remote control in direct heat or in a
damp place as you may damage the remote.
APlace the remote control face down, then open the
Please use two AAA 1.5V batteries. Do not mix battery
types. Install the batteries at the correct polarities. Do
not use rechargeable batteries. If your TV is to be stored
for a period of time, remove the batteries from the
remote control.
cover of the battery compartment.
Getting Started
BInstall two AAA batteries. (The + and - symbol of the
battery must match with the marks on the remote).
SETTING UP
LOCATION
You will need to place your TV near your plug socket
(so the power cable can comfortably reach) and within
reach of your aerial socket or extension lead.
CClose the cover of the battery compartment.
CONNECTION
AInsert your TV aerial lead into the Antenna input at
the side of the TV.
BInsert the batteries into the remote control. Make
sure they are inserted the right way around,
matching the polarity as indicated inside the battery
compartment.
SWITCHING YOUR TV ON
AConnect your TV to the mains electrical supply
Note: The red light at the bottom of the TV will be
on whenever the TV is in standby and there is power
to the TV.
BTouch the POWER button on the right side of the TV
Digital LED LCD Television Instruction Manual EN-10
Getting Started
once. The red light at the bottom of the TV will flash
for a few seconds and then the picture will appear.
CWith the TV connected to the mains electricity
supply, press the red POWER button on the remote
control. The red light at the bottom of the TV will
flash for a few seconds and then the picture will
appear.
DOn initial switch on only. Select your chosen
language when prompted from the list that will
appear on screen. Use the 4button to scroll to the
language you want and press to confirm.
Note
The Power buttons toggle the TV between Standby
and ON. To remove power from the TV, switch off
and unplug the TV from the mains supply.
TUNING YOUR TV
BPress 34 button to select Tuning menu, press 
button to enter.
CPress 5 button to select Country item.
Press 34 button to select you needed.
DPress 5 button to select Auto Search item, press
OK button to enter.
Press  button to select the OK option, and press
OK button to start searching.
Press the MENU button, you can choose to skip the
TV /DTV Search or not.
SWITCHING TO AN EXTERNAL
SOURCE OTHER THAN THE TV
If you have attached a DVD player or similar external
device to the TV, you will need to tell the TV to display
the content from it. Simply press SOURCE which will
bring up the source menu in the left corner of the screen,
use the 5 and  button to highlight the required
source and press OK select.
For details of how to plug in other equipment see GET
TO KNOW YOUR TV on page 6.
DTV
EPress EXIT button to stop auto search during
searching.
Note
❏❏ It may take a few moments to complete the Auto
Search.
DIGITAL MANUAL SEARCH
APress MENU button.
AUTO SEARCH
APress MENU button.
EN-11 Digital LED LCD Television Instruction Manual
Getting Started
BPress 34 button to select Tuning menu, press 
button to enter.
CPress 6 button to select Digital Manual Search
item, press 4 button to enter.
DPress 56 button to select Search item, press4
button is used to select the higher frequency
channel.
Press  button is used to select the lower frequency
channel.
DPress 34 button to select the Channel.
Press OK button to start searching.
EAnd then select Storage To, press34 button to
select the position number you want the channel
on. Once a channel is located, you can press red
button to save it. Press EXIT button to exit.
EOnce a channel is located, you can press OK button
to save it.
Press EXIT button to exit.
❖❖Sound System
Analog Manual Search
Press button to select “Sound System”, then
press 4 button to select the correct sound system.
Follow the below steps when you need to have a manual
search.
❖❖Current CH
Press 34 button to select the channel number to
edit.
APress MENU button.
❖❖Storage To
Press 34 button to select the program number you
want to storage to.
❖❖Fine tune
If the picture and/or sound are poor, try using the
FINE TUNE feature. Do not use this feature unless
reception is poor.
ARepeat above steps A-C, then press button to
select the Fine Tune item.
BPress 34 button to select Tuning menu, press
BPress 34 button repeatedly to carry out fine
button to enter.
tune, till the best picture and sound are obtained,
then loosen the button.
CPress 56
button to select Analog Manual Search
item, press 4 button to enter.
Channel Edit
Using this function, you can rename, move, set favorite
channel and skip the channel in the analogue mode.
APress MENU button.
Digital LED LCD Television Instruction Manual EN-12
Getting Started
BPress 56 button to select the number position you
want to remove to, press yellow button to confirm.
CYou can press the EXIT button to cancel the changes
at anytime.
Setting favourite channel
APress 56 button to select the channel, press red
BPress 34 button to select TUNING menu, press 6
button to enter.
CPress 56 button to select CHANNEL EDIT item.
Press 4 button to enter the sub-menu. You can
press red, green, yellow or blue button to enter the
menu you need.
RENAME
APress  button to select the channel, and press
green button to rename.
button to set your favourite channel.
BYou can press the red button to cancel the changes
at anytime.
CPress FAV button on the remote control and
Favourite List will be displayed.
DPress56 button to select the channel, and press
OK button to enter.
SKIP
APress56 button to select the channel and press
blue button to skip the current channel.
BYou can press the blue button to cancel the changes
at anytime.
GUIDE (Electronic Program Guide)
Using this function, you can access the DTV program
information.
BPress34 button to select the number position of
APress MENU button.
channel name. Press 56 button to select number.
CYou can press the EXIT button to cancel the changes
at anytime.
Note
❏❏ The RENAME function is only available in ATV
program.
MOVE
APress 56 button to select the channel and press
yellow button to select the position.
EN-13 Digital LED LCD Television Instruction Manual
BPress 34 button to select TUNING menu.
Press button to enter.
Getting Started
CPress5 button to select the guide item.
CI Slot
Press OK button to enter the submenu, the
electronic program guide is displayed.
You can quickly call up Guide menu by GUIDE
button on the remote control.
CAM
Smart Card
Note
❏❏ Only DTV mode.
COMMON INTERFACE
BTurn on the TV and it will display the below message
if the CA module is detected. Wait for few moments
until the card is activated.
The common interface (CI) slot is designed to accept the
Conditional Access (CA) Module and Smart card in order
to view the pay TV programmes and additional services.
Contact your Common Interface service provider to get
more information about the modules and subscription.
Please note that CA modules and smart cards are neither
supplied nor optional accessories from us.
CPress the MENU button to display the Main Menu
and use the  and  button to highlight the
“Common Interface” line and press the “OK” button.
DDetailed information on the CI card in use is
displayed.
EPress OK button to access the card menu. Refer to
the module instruction manual for setting details.
FWhen module is removed, the following message
will appear on the screen.
Warning
Software Update function
•• Switch off your TV before any module is inserted in
the Common Interface slot.
•• When you get the updating news from the TV shop’s
web, you can update the operating software using
the Download menu. The data for various units are
transferred consecutively on a special receiving
channel.
•• You need to search the channel with updating code
stream.
AInsert the CAM correctly, then Smart Card to the CI
slot that is located at the side of the TV.
Digital LED LCD Television Instruction Manual EN-14
Getting Started
FPress 5 button to select the Start Upgrade option
and use OK button to enter. Then the TV will restart
and search the upgrade information.
Note
❏❏ If the upgrade information is received, the TV will
begin to upgrade. Or else, the TV will go back to
the DTV source.
GLoad the receiver identification. This process may
Note
❏❏ You can get information from the TV shop or
internet.
also take several minutes. You can press EXIT button
to cancel the download and your TV set will go back
to the DTV source.
100%
Operation
Press EXIT to cancel download
Updating in progress - Do not turn off the TV
APress MENU button.
15%
HAfter the download has finished, your TV set will
enter configuration state and the indicator light is
shining. The menu 4 of right appears.
The set will be back the DTV source when the update is
completed.
BPress 34 button to select TUNING menu, press 
button to enter.
CPress 56 button to select Software Upgrade item.
DPress 34 button to set it as On. (The default is Off )
EThe Start Upgrade item can be selected.(The default
is grey and cannot be selected).
USING YOUR TV
How to select the TV program
AUsing Program number button Enter the channel
number with the number keypad on the remote
control.
BUsing P+/P- button.
Press the P+/P- button to select a channel number.
13%
Press EXIT to cancel download
HOW to adjust volume
Press V+/V- button on the remote control or the side of
the TV to adjust the volume level.
EN-15 Digital LED LCD Television Instruction Manual
Getting Started
❖❖Colour
CH.LIST function
This will adjust the saturation level of the colours to
suit your personal preference.
Press CH.LIST button on the remote control will display
Channel List menu, and then press  button to enter.
Press56 button to select the channel, and then press
OK button to enter.
❖❖Sharpness
This will adjust the sharpness of fine details in the
picture.
❖❖Tint
ADJUSTING PICTURE
Allows you to select the colour mix (Tint) of the
picture.
SETTINGS
Note
❏❏ The Tint function is only available in NTSC mode.
Changing the Picture Setting
❖❖Mode
This will select the picture mode. Select Standard/
Mild/User/Vivid according to the program. You can
quickly select the desired mode by P.MODE button on
the remote control.
APress MENU button.
❖❖Colour temperature
This will increase or decrease Warm (red) and Cool
(blue) colours to suit personal preferences.
Select Cool to give the white colour a blue tint,
Normal to give the white colour a neutral tint, Warm
to give the white colour a red tint.
❖❖Noise Reduction
Automatically filters out and reduces the image noise
and improves picture quality when receiving weak
video signals.
Select Off/Low/Standard/High according to the
image noise.
BPress 34 button to select Picture menu, press 
button to enter.
CPress 5 button to select the item requires
adjusting.
❖❖Reset
DPress34 button to adjust the selection item.
EWhen you are satisfied with your choice, press the
To recover to the default value.
EXIT button to return to normal viewing or press
MENU button to return to the previous menu.
ADJUSTING SOUND
❖❖Contrast
SETTINGS
This will adjust the intensity of bright parts in the
picture but keep the dark parts unchanged.
❖❖Brightness
Changing the Sound Setting
This will adjust the light output of the complete
picture, which will mainly affect the darker areas of
the picture.
APress MENU button.
BPress34 button to select Sound menu, press 
button to enter.
Digital LED LCD Television Instruction Manual EN-16
Getting Started
CPress  button to select the item requires
adjusting.
DPress 34 button to adjust the selection item.
EWhen you are satisfied with your choice, press the
EXIT button to return to normal viewing or press
MENU button to return to the previous menu.
❖❖Audio Languages
Press 56 button to select Primary/Secondary item,
and then press 4 button to select the languages
you needed.
Press  button to select Close item, press OK button
to close it.
❖❖Balance
This will adjust the output of the right and left
speakers to obtain the best stereo reproduction for
your listening position.
❖❖Mode
This will select the sound mode.
Press 34 button to select Standard/Music/
Theater/User according to the program. You can
quickly select the desired mode by S.MODE button
on the remote control.
❖❖AVL (Automatic volume control)
This will reduces the differences in volume level
among broadcasters.
❖❖SRS TS XT
This will control the Woofer output.
Press  button to select SRS TS XT.
Press 34 button to set SRS TS XT as OFF, ON.
Note
❏❏ The Audio Language function is only available in
DTV mode.
❖❖Reset
To recover to the default menu setting.
FUNCTION SETTINGS
APress MENU button.
❖❖Digital Audio Output
This will control the Digital Audio Output.
Press button to select Digital Audio Output.,
Press button to set Digital Audio Output. as OFF,
PCM,RAW.
❖❖Equalizer
This sound setting can be adjusted to suit your
personal preference.
BPress34 button to select Sound menu, press 
button to enter.
EN-17 Digital LED LCD Television Instruction Manual
Getting Started
at top sides and no alteration, at bottom side.
❖❖Blue Screen
This will select the character background colour.
Note
❏❏ The Blue Screen function is only available for
ATV mode.
❖❖Recorder
CPress  button to select the item requires adjusting.
DPress34 button to adjust the selection item.
EWhen you are satisfied with your choice, press the
To record the DTV program. Details of Recording are
described on the page of 25-27.
❖❖SCART Input
The item does not work.
EXIT button to return to normal viewing or press
MENU button to return to the previous menu.
❖❖OSD Time Out
To set how long you want the menus to appear
on-screen. Each press of 34 button repeatedly to
select the number of preset minutes, the Time will be
set in sequence: off, 10sec, 15sec, 30sec, 45sec, 60sec.
❖❖Language
To select the menu language.
❖❖Subtitle Language
To select the Subtitle language.
❖❖Display Mode
To set the picture proportion, press34 button to
select 4:3/Zoom1/Zoom2/Wide/16:9/Auto. You can
quickly select the desired mode by SCREEN button
on the remote control.
•• 4:3 mode
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio, with gray bars
appearing at both the left and right sides.
❖❖OSD Transparency
To set the transparency background of OSD, the
transparency will be set in sequence: Off, 25%, 50%,
75%, 100%.
•• 16:9 mode
Choose 16:9 when you want to adjust the picture
horizontally, in a linear proportion to fill the entire
screen.
❖❖Reset
To recover to the default value.
•• Zoom1
Choose Zoom1 when you want to view the picture
without any alteration. However, the top and
bottom portions of the picture will be cropped.
•• Zoom2
Choose Zoom2 when you want the picture to be
altered, both vertically extended and cropped.
The picture taking a halfway trade off between
alteration and screen coverage.
•• Wide
Choose Wide when you want to adjust the picture
in a non-linear proportion, that is, more enlarged
Digital LED LCD Television Instruction Manual EN-18
Getting Started
TIME SETTINGS
❖❖Clock
APress MENU button.
BPress 34 button to select Time menu, press 
ATV mode, then turn on the TV.
❖❖Off Time
APress MENU button.
BPress 34 button to select Time menu, press 
button to enter.
button to enter.
CPress 56 button to select Clock item, press 4
CPress  button to select Off Time item, press 
button to enter setting.
Press 56 button to select hour or minute, press
34 button to adjust the value.
❖❖Date
APress MENU button.
BPress 34 button to select Time menu, press 
button to enter.
button to enter setting.
Press  button to select Repeat option, and
then press4button to set it on.
Press56 button to select hour or minute, press
34 button to adjust the value.
When the off time has arrived, the TV set will
enter into standby mode.
❖❖Sleep
The sleep timer automatically shuts off the TV after a
preset time (from 5 to 240 minutes).
APress the MENU button and then use 34 button
to select the Time menu.
CPress  button to select Date item, press 
button to enter setting.
Press button to select the option, and then
press 3 button to adjust value.
BPress the  button and then use 5 button to
select the Sleep.
CPress the 34 button and then use 34 button
Note
❏❏ In DTV mode, because the time information is
from the signal, the Clock and Date are not able
to be changed.
If you want to change the time, turn off the TV in
EN-19 Digital LED LCD Television Instruction Manual
to select the number of minutes. Select Off, 5Min,
10Min, 15Min, 30Min, 45Min, 60Min, 90Min,
120Min, 180Min, 240Min.
DWhen you are satisfied with your choice, press
MENU button to return to the previous menu or
Getting Started
press the EXIT button to return to TV viewing.
And the time begins to count down from the
number of minutes selected.
❖❖Time Zone
APress MENU button.
BWhen you have inputted the four digits you will
be prompted to enter it again.
Your new password will then be automatically
saved.
❖❖CHILD LOCK
Press 56 button to select Child Lock.
Press 34 button to set On or Off mode. If lock on
mode is set, Child Lock is in activated automatically.
In such case, if the buttons on the television is
pressed, the screen will display Child Lock, which
will disappear automatically after the latest pressing
5 seconds. The Child Lock mode can be resumed by
entering Lock Set menu, set Child Lock On or Off.
BPress 34button to select Time menu, press 6
button to enter.
CPress 56 button to select Time Zone item.
DPress 34 button to select the correct time zone.
EPress MENU button to save and exit.
❖❖Tuning Lock
LOCK MENU SETTING
Press 56 to select Tuner Lock and 34 to set On/Off.
(To set On, some operation such as search will be not
available. When enter the Tuning menu, Tuner Lock
will be on the screen. If you want to operate Tuning
menu, you need to enter the Lock menu to set Tuner
Lock Off or operate unlock.)
Using this function can control the tuner, program,
source volume and so on. Pressing MENU on the remote
control, press 34 button to select Lock menu, press 
button to enter the sub-menu, and you will be required
to enter the password. The initial password of the
television is 0000. If you forget your password, you can
always input 9443 to regain control.
❖❖Channel NO.
Channel NO. is opted for setting up preset channel.
Press 56 button to select preset Channel. Press 34
button to select channel number.
❖❖Source Selection
Source Selection is used for selecting the source (your
DVD player, satellite PC etc. connected to this TV) of
the program you want to watch.
On the remote press SOURCE button then either 56
buttons to select:- DTV (Digital TV), TV (Analogue),
SCART, Component, PC, HDMI1, HDMI2, HDMI3, or
USB as required. Then press the OK button.
Note:DVD is not available on some models.
❖❖CHANGE PASSWORD
APress 56 button to select Change Password
item. Press  button to enter the submenu.
❖❖Source Lock
Source Lock will control the On or Off of hinder
external input modes.
Press 34 button to set as on or off.
Digital LED LCD Television Instruction Manual EN-20
Getting Started
When the source lock is set as on, TV source will
display, at this time, when press SOURCE button,
the TV can switch to corresponding source and will
display the Source is locked.
BPress 56 button to select the item and press OK
button to enter. You can press the EXIT button to
cancel the changes at anytime.
Note
❏❏ Press SUBTITLE button on the remote, it will
display subtitle languages menu only in the DTV
mode.
❖❖Max Volume
Press 56 button to select Max Volume. Press 
button for adjustment between 0-100. If a certain
Value is set, when volume is being adjusted, the
sound value can not exceed maximum volume value.
If current volume is over Max Volume, when lock set
menu is set, current volume will become set maximum
volume, if current volume is below maximum volume,
customer set volume will stay unchanged.
❖❖CH.LIST Function
APress CH.LIST button on the remote control, will
display Channel List menu.
❖❖Initial Volume
The TV will remember it after your setting, that will
be the volume when turning back on the TV the next
time.
❖❖Parental Lock
Press 56 button to select parental lock. Press 34
button to select OFF or 4-18 to limit the age of
children who will watch TV.
❖❖Clear Lock
Press 56 button to select Unlock mode. Press 34
button to unlock all set modes, setting all lock options
to off, and the maximum volume returns to 100.
SHORTCUT MENU
BPress  button to select the channel and press
OK button to enter. You can press the EXIT button
to cancel the changes at anytime.
❖❖GUIDE Function
Press GUIDE button on the remote control, will
display Program Guide menu, press 5634button
to select the program.
You can press the EXIT button to cancel the changes
at anytime.
DISPLAY
❖❖Subtitle Function
APress SUBTITLE button on the remote control will
display Subtitle languages menu, press 6 button
to enter.
Note
EN-21 Digital LED LCD Television Instruction Manual
Getting Started
APress the MUTE button on the remote control and
❏❏ Available only in the DTV mode.
“Mute” type face will display on the lower part of
the screen. At this Time, the sound of the TV set is
turned off.
❖❖FAV Function
Press FAV button on the remote control, will display
Favourite List menu.
Press  button to select program and press OK
button to enter. You can press the EXIT button to
cancel the changes at anytime.
BIf you want to recover the sound, press the MUTE
button again or directly press V+ button.
❖❖Quick program view
This function enables quick swap to the last watched
program. Press Q.view button, and the TV will be back
to the TV source, except in the USB and DVD source.
ASuppose the channel number you used just now
is 8 and the channel number you are using is 18
(as shown in the figure).
❖❖INFO
Press INFO button on the remote control, will display
the current channel information.
You can press the EXIT button to cancel the changes
at anytime.
❖❖AUDIO/I/II
Press AUDIO button on the remote control, will
display Audio Languages menu.
Press  button to select the desired settings and
press OK button to enter.
You can press the EXIT button to cancel the changes
at anytime.
BIf you want to return to the last watched program
channel 8, you can simply press the Q.View button.
CIf you want to return to channel 18, press the
button again. Use this function, you can easily
change between the channel you are using and
the channel you used last Time.
Note
❏❏ Press AUDIO button on the remote, it will
display Audio Languages menu only in the DTV
mode.
❖❖Eliminate Sound
When you need to pay attention to surrounding
sounds, or there is a telephone call or there are some
guests visiting you, the sound elimination (mute)
function is very convenient.
Digital LED LCD Television Instruction Manual EN-22
Using the features
USING THE FEATURES
Teletext functions
Teletext is an information system, broadcast by certain
channels, which can be read like a newspaper. It also
provides subtitles for people with hearing difficulties or
those who are unfamiliar with the language in which a
particular program is being broadcast (cable networks,
satellite channels, etc.).
❖❖Mix mode
To view the TV picture while in Text mode press the
button, this will superimpose the Teletext data on top
of the TV picture. Press this button again to return to
Full text.
❖❖INDEX
Press the INDEX button to go to the index page of
teletext.
Note
❏❏ The teletext buttons could be working even if
there is no teletext signal, but there is no teletext
display.
❖❖Language change
Pressing the
button will change the Teletext
characters between Eastern and Western.
Teletext
❖❖Teletext functions
To select “teletext” press the
button on the
handset. To switch off teletext, press the button again.
“Note all menu functions are not available in teletext
mode”. Only a few direct button control functions are
available in teletext mode, they are:
•• Volume adjustment
•• Mute function
❖❖Hold
Pressing the button will stop the teletext page
automa­tically updating. This feature is very useful
where there are several teletext pages or data on the
same page number.
❖❖Size
❖❖Page up/down
Use the P+/P- buttons to browse next or previous
page.
Pressing the button changes between full screen
top half bottom half full screen. This feature is
very useful as it magnifies the image making the
characters easier to read.
❖❖Reveal
❖❖Page number entering
To select a Teletext page, enter the page number
using the numeric key pad on the remote control,
or use the P+ or P- buttons, or the coloured Fast text
buttons.
Pressing the
button will reveal hidden text. This
feature is used to reveal information such as answers
to Teletext on-line interactive puzzles.
❖❖Hide
Pressing the
EN-23 Digital LED LCD Television Instruction Manual
button will hide text.
Using the features
BSupported equipment:
❖❖Time
While in normal TV mode only, pressing the button
will display the teletext time in the top right hand
corner for a few seconds.
Support the equipment that supports Mass Storage
Protocol and whose file system is FAT32, such
as some USB disks, mobile harddisks, and MP3
player. If USB equipment could not be identified
due to unsupported file system, please format the
equipment to the above-mentioned file system.
CTo achieve smooth playing, ensure the following:
❖❖Fast text coloured buttons
Fast text automatically displays the four most
commonly used pages that the broadcaster thinks
that you may want to choose next. Press the same
coloured button on the remote control as the
coloured link at the bottom of the teletext page to go
directly to that page.
❖❖Subcode
Pressing the button by entering its 4-digit number
to enter a secondary page.
• The file code rate should be lower than 300KB/S;
• Due to the limitation of USB signal transmission
distance, it is recommended not to use USB patch
cord, in case of using the cord, make sure that its
length is not over 1m;
• Use high-speed USB equipment in conformity
with USB2.0 full speed Interface Standard; If USB
equipment in conformity with USB1.1 full speed
Interface Standard is used, the playing may be
unsmooth.
When connecting/removing the USB
device
APress “SOURCE” on the remote control unit to select
USB option.
USB MODE
BInsert USB equipment into corresponding USB
interface 2s after starting the system.
CAfter entering the system menu, press “3/4“ on the
Note
❏❏ The diagrams in the following section are
schematic and only for your reference. Please see
the actual product if necessary.
❏❏ The OSD of the USB function may be somewhat
different from your product because it is just
example to help the instruction.
DPress “5/6“ on the remote control unit to select the
required file, press “OK” button to enter the selected file.
ETo exit the streaming media playing system and
watch a TV program, you must press “BACK” button
to return to the streaming media main menu at first
(to protect equipment), and then press “SOURCE” to
select “TV” to return to the TV mode.
TO USE THE USB DEVICE
ASupported file formats:
•
•
•
•
remote control unit to select the require USB files,
press “OK” button to confirm the selection and enter
the file list relative to the selection.
Photo: *.jpg;
Music: *.mp3 files;
Movie: *.avi files;
TEXT: *.txt (Only on some models)
Note
❑❑ Under source of USB, when press button MENU,
screen goes black, except when images or movies
are being played.
Note
❏❏ Due to the particularity of file recording, some files
may be unable to be read.
❑❑ While playing the USB, press “BACK” button
repeatly, the screen picture will return to USB
main interface, and only at this time you can
switch corresponding signal sources by pressing
“SOURCE” again.
Digital LED LCD Television Instruction Manual EN-24
Using the features
❑❑ Please do not unplug the USB device when the
connected USB storage device is working. When such
device is suddenly separated or unplugged, the stored
files or the USB storage may become damaged.
Operating the USB device
APress “5/6“ to scroll through main menu or
submenu and select your desired option.
BPress “OK” to confirm your selection.
CPress “/“ to achieve the FWD (fast forward) and
REV (fast back) of the option being played.
DIf you want to pause the picture which is being
played, press the PLAY/PAUSE button again.
Press ”ZOOM“ to magnify the picture. When the
picture is enlarged, press “3/4“ and “/“ to
move the picture.
Press “PREV/NEXT“ to select the last or next picture.
Press “5/6“ to rotate the picture.
Press “STOP” to stop the picture being played.
ETo exit playing, just press “BACK” repeatedly.
Note
❏❏ The menu display varies with the photo name and
pixel in your equipment.
DPress “PLAY/PAUSE” to play, and press it again to
pause playing.
EPress “ZOOM” to magnify pictures; when the picture is
enlarged, press “3/4“ and “5/6“ to move the picture.
FPress “STOP“ to stop playing, or return to the
previous menu, and press “BACK” repeatedly to
return to the main menu.
Playing Music
AAfter entering USB main interface, press “3/4“ to
select “MUSIC”.
BPress ”OK“ to confirm the selection and enter the
music file list.
Note
❏❏ You can choose the photos or music in different
files to play together.
Playing a Picture
AAfter entering USB main interface, press “3/4“ to
select “PHOTO” item.
BPress ”OK“ to confirm the selection and enter the
picture file list.
CPress “5/6“ and “OK” button to select the music
you want to play, then press “PLAY/PAUSE“ button
to play the music.
Press “/“ to achieve the REV (fast back) and FWD
(fast forward) of the music being played.
Press “PREV/NEXT “ to select the last or next music.
Press “STOP“ to stop the music being played,
when the current interface is the music being
played.
DTo return to the main menu, just press “BACK”
repeatedly.
CPress “5/6“ to select the picture you want to play,
press ”OK“ to confirm, and then press “PLAY/PAUSE”
button to play the pictures.
EN-25 Digital LED LCD Television Instruction Manual
Note
❏❏ You can enjoy the music and the picture at the
same time.
Using the features
DTo exit the “Text” mode, just press “BACK” repeatedly.
Playing a Movie
AAfter entering USB main interface, press “3/4“ to
select “Movie”.
BPress “OK” to confirm the selection and enter the
movie file list.
Note
❏❏ You can enjoy the music and the text at the same
time.
USING EXTERNAL USB DEVICE
FOR RECORDING
APress the Source button and pressbuttons to
select TV and press the OK button.
CPress “/“ and “OK” button to select the movie
you want to play, and then press “PLAY/PAUSE”
button to play the movie.
Press “ZOOM” to magnify the picture.
Press “PREV/NEXT “ to select the last or next movie.
Press “STOP“ to stop the movie being played.
DTo exit playing, just press “BACK” repeatedly.
Note
❏❏ Only USB1 is available for recording.
BInsert the USB device with FAT32 format into
theUSB1 connector. Then, press MENU button.
Text
CPress34 button to select FUNCTION menu,
AAfter entering USB main interface, press “3/4“ to
select “Text” .
BPress “OK” to confirm the selection and enter the
pressthe OK button to enter .
DPress 56buttons to select Recorder. Press OK
button to enter the submenu.
text file list.
EPress 56button to Select Disk and press 4
CPress “5/6” and “OK” button to select the text you
want to play, and then press “PLAY/PAUSE” button
to play the text.
Press “PREV/NEXT “ to select the last or next text.
or OK
button to enter. Press34button to select disk if
your device has several disks..
Digital LED LCD Television Instruction Manual EN-26
Using the features
Note
Note
❏❏ If this is not the first time the USB has been used to
record you can check the device Time Shift size and
speed by selecting Check File System.
Press 56 buttons to select Check File System,
press the OK button and after a short delay the
on screen display will show Time Shift size, the
streaming speed and the picture standard, either
HD, SD or REC. For first time use of the USB device:
❏❏ If you select all the size format for time shift, you
cannot do any recording
FPress 56
button to select Format and press 4to
enter. Press 34button to select the size you wantto
format. Press OK button to format the USB Disk.
Note
❏❏ The system will format the whole device and if your
device size is bigger than 1 GB, you can set the size
which is used for time shift.
GFormat may take several minutes and the time
isdepending on the memory size. Press34buttonto
select the Time Shift Disk Size. The max device sizefor
Time Shift is 8GB. Then, press OK button to save.
HWaiting for the system to finish checking.You can
seethe speed data displayed on screen after the
checking is completed.
Note
❏❏ You only have to format when you use the device
for recording for the first time.
❏❏ The minimum device size for record is 1GB.
Providedevice formatting function is up to 2TB.
The maxMulti-Partition is 16 partitions and one is
active ata time.
❏❏ Bit rate:
•• Device bit-rate>4.5MB/s REC is is good at HD
streaming speed.
•• Device bit-rate>1.5MB/s REC is good at
SDstreaming speed.
•• Device bit-rate<600KB/s REC is bad for REC.
•• Keep all cables as short as possible the keep
streaming speed as high as possible.
❏❏ The system cannot work normally if the USBdevice
has the problems listed below:
•• The device has bug.
•• The device has error block.
•• The device size less than 1GB or exceeds the
Time Shift maximum.
•• The device is not FAT32 format
IMPORTANT
•• The USB device should be formatted as FAT32
format. This can be done by your PC (refer to PC
software instructions for formatting a device to
FAT32 format) before inserting the USB device into
the USB Port.
TIME SHIFT
EN-27 Digital LED LCD Television Instruction Manual
Using the features
Time Shift function is only available in DTV mode.
❏❏ Press PLAY/PAUSE to pause the program, and
press PLAY/PAUSE again, the time shift program
will be played. If you want to stop time shift
function, press the STOP button.
❏❏ You can stop the time shift program being played
by pressing the STOP button.
RECORDING
APress D.MENU button to record the program being
played, and press D.MENU or EXIT button to make
the recording interface minimum.
Note
❏❏ Changing the channel will not influence the
recording in the same frequency, but will influence
the time shift. When the recorded program is being
played, you can not delete it.
❏❏ Press the INDEX button repeatedly, the program
will be displayed in the order of program name,
channel name, program time, file name and file
length.
BPress STOP button to stop the program recording
being played.
CFor Playback of the recorded program. Press INDEX
button to open the recorded list.
Press 56 button to select the content you recorded.
Press the 4 button to display the program
information.
Press 3 button to cancel.
Press OK or PLAY/PAUSE button to play the
program recorded and press STOP button to stop it.
Digital LED LCD Television Instruction Manual EN-28
Reference Sectionss
Reference Sections
TROUBLESHOOTING
„„ To assist in location of possible faults use the help guide
below:
No picture, no
sound
Verify if the television is
properly plugged in.
Verify if the television has a
proper supplied power source.
Verify if electricity is available.
Blank screen
Verify if correct signals are
input.
Operate the remote to change
signal input to correct input.
Restart the television if power
supply is interrupted.
No sound
Press MUTE button and verify if
Mute mode is set.
Switch to other channel and
verify if the same problem
happens.
Press VOL+ button to see if the
problem can be solved.
Poor sound
Verify if sound system is correct.
Refer to user‘s manual for
adjustment.
No picture in
some channel
Verify if correct channel is
selected.
Adjust the antenna.
No color for
some channel
program
(black and
white)
Verify if the same problem exists
in other channels.
Check out of picture and sound
systems.
Refer to relative instructions
in the Manual for color
adjustment.
Spots with
some or all
pictures
Verify if the antenna is correctly
connected.
Verify if the antenna is in good
condition.
Make fine adjustment of
channel.
EN-29 Digital LED LCD Television Instruction Manual
Television out
of control
Disconnect the television from
power supply and 10 seconds
later, connect the television
to the power supply. If the
problem still exists, contact
authorized after-sales service
for technical assistance.
Note
❏❏ If the fault can not be repaired using the above
guide consult with your local authorized service
centre.
❏❏ The TV set must only be repaired by a qualified
registered service person. Never attempt to
remove the back cover as the TV set has dangerous
voltages in side that may cause a fatality or fire.
Using the features
41&$*'*$"5*0/
-
8W+8W
,
, PC/DVI Audio input,
,
,
4FFSBUJOHQMBUF
4FFSBUJOHQMBUF
2EMOTECONTROL!!!BATTERY§)NSTRUCTION-ANUAL7ARRANTY1UICK3TART'UIDE
463TAND
83CREWSFOR46STAND
#OMPONENTADAPTER#OMPONENTAUDIOADAPTER3#!24ADAPTER
#OVERBOTTOM
5IFQBSUTQFDJmDBUJPOTPGUIJT57TFUQSPWJEFEIFSFBSFGPSSFGFSFODFPOMZ
%JõFSFODFTNBZPDDVSBTQSPEVDUUFDIOPMPHZJTVQEBUFE
%FTJHOBOETQFDJmDBUJPOTBSFTVCKFDUUPDIBOHFXJUIPVUOPUJDF
Digital LED LCD Television Instruction Manual EN-30
Download PDF
Similar pages