The most trusted, dependable name in projector lamp sales.

The most trusted, dependable name
in projector lamp sales.
http://www.myprojectorlamps.com
http://www.myprojectorlamps.ca
http://www.myprojectorlamps.eu
The following projector manual has not been modified or altered in any way.
DATA PROJECTOR
V3-131/ V3-111
E
V
O
2
L
E
E
S
TA
N
D
B
Y
G
R
B
V
E
ID
O
A
C
N
E
C
F
E
L
R
E
R
N
M
E
T
E
N
U
Z
E
1
M
T
U
E
Q
U
K
IC
Q
C
O
K
S
T
3
N
A
T
U
O
Z
O
A
4
S
O
P
M
E
T
C
T
IM
R
P
U
S
H
S
TA
N
D
B
Y
S
S
TA
N
TA
D
B
TU
Y
S
A
U
TO
S
O
U
R
C
E
User’s Manual
IMPORTANT
* DLP™ (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U.S.A.).
* DMD is an ultra-precise part developed by Texas Instruments (U.S.A.) which takes the place of liquid crystal (in the
projector).
* VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U.S.A.).
* S-VGA is a registered trademark of Video Electronics Standards Association.
* Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corporation (U.S.A. and other countries).
* Macintosh is a trademark of Apple Computer Inc. (U.S.A.).
Note that even in the absence of explanatory notes, serious attention is paid to the trademarks of the various companies
and to the product trademarks.
IMPORTANT SAFETY INFORMATION
Precautions
Please read this manual carefully before using your PLUS Data Projector and keep the manual handy for future
reference.
These operating instructions apply to both models V3-131 and V3-111.
The two models are identical in appearance but have different display resolutions and projection distances.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude
to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside
of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of
this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
The above cautions are given on the bottom of the product.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE
THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE
PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED PLUS SERVICE PERSONNEL.
Hg: Lamp in This Product Contains Mercury. Dispose of Lamp According to Local, State or Federal Law.
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
RF Interference
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT
those specified by PLUS Vision in this manual. Failure to comply with this government regulation could void
your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
DOC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
E-2
IMPORTANT SAFETY INFORMATION
Important Safeguards
These safety instructions are to ensure the long life of the unit and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
•
•
•
•
•
•
For best results, use the unit in a darkened room.
Place the unit on a flat, level surface in a dry area away from dust and moisture.
Do not place the unit in direct sunlight, near heaters or heat radiating appliances.
Exposure to direct sunlight, smoke or steam can harm internal components.
Handle the unit carefully. Dropping or jarring can damage internal components.
Do not place heavy objects on top of the unit.
Power Supply
• The unit is designed to operate on a power supply of 100 - 240 V 50/60 Hz AC. Ensure that your power supply
fits these requirements before attempting to use the unit.
• Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or
fire.
• Disconnect the power cable (mains lead) from the power outlet after using the unit.
Before disconnecting the power cable, make sure that the STANDBY indicator lights in amber (not blinking or
in green).
Cleaning
• Disconnect the power cable (mains lead) from the unit.
• Clean the cabinet of the unit periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use
strong detergents or solvents such as alcohol or thinner.
• Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
• Clean the ventilation slots and speaker grills on the unit periodically using a vacuum cleaner. If accumulated
dust blocks the ventilation slots, the unit will overheat, which may cause the unit to malfunction.
Use a soft brush attachment when using the vacuum cleaner. Do not use a hard attachment, such as a crevice
tool, to prevent the damage to the unit.
Lamp Replacement
• Be sure to replace the lamp when the Status indicator comes on. If you continue to use the lamp after 2000
hours of usage, the lamp will turn off.
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the buildup of heat inside
the unit. Allow at least 10 cm (4 inches) of space between the unit and walls.
• Prevent foreign objects such as paper clips and bits of paper from falling into the unit. Do not attempt to retrieve
any objects that fell into the unit. Do not insert any metal objects such as a wire or screwdriver into the unit. If
something should fall into the unit, immediately disconnect the power cable from the unit and have the object
removed by a qualified PLUS service person.
• Do not place any liquids on top of the unit.
Carrying around
When carrying the unit around, please use the storage case that comes with it and, to protect the lens from
scratches, always shut the sliding lens shutter. Also, do not subject the unit to strong mechanical shock.
CAUTION – HOT!
The area around the exhaust vents is hot during and immediately after image projection.
To avoid burns, keep your hands away from this area.
Wait until the exhaust vents area cools off before touching it.
Do not look into the lens while the unit is on. Serious damage to your eyes could result.
E-3
Major Features
䡵 World’s thinnest projector – just 35 mm thick
Plus is seeing just how thin the projector can be made. With our retractable lens and other unique ideas and technologies, we
have developed a projector just 35 mm thick, something previously considered impossible.
䡵 Designed for portability
The flat design allows the projector to fit in a regular business bag along with documents and a laptop. Thanks to the sliding
type lens shutter, the lens is protected without any parts jutting out.
䡵 Sharp, clear picture
The DLP™ display system affords RGB color fidelity and inconspicuous gaps between the individual dots, thereby permitting
the display of small characters and diagrams with distinct clarity.
䡵 High contrast ration of 2000:1
Use of a new generation of DMD devices has given birth to an amazing 2000:1 high contrast ratio.
By widening the difference of brightness between black and white, you can see a degree of sharpness that is greater than just
the brightness based on specifications.
䡵 Powerful functions for presentations
A wide variety of easy-to-set functions have been built into the projector, from a digital keystone correction function (used
when making settings) that corrects picture distortion, to an auto adjustment function that automatically identifies the PC
signal.
There is also a built-in “Presentation Timer” function for further presentation convenience.
䡵 Great moving image playback capabilities using the same principles as DLP Cinema
technology
Plus DLP type projectors have the same makings as the DLP Cinema technology used in movie theaters. Because of their
extremely fast response, even images with much movement – sports, movies – play smoothly without blurring.
䡵 Security lock function
The lock can be set so that a password must be input when the projector is started up. Without the correct password, no
operations other than turning the power on and off can be performed. This function effectively protects the projector from
unauthorized use.
䡵 Eco-mode switch function for the lamp output
Using the lamp Eco-mode will extend the life of the lamp and lower the power consumption.
By switching the lamp mode to suit your operating environment, you will save on lamp cost as well as contribute to energy
conservation and ecology.
E-4
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................................... E-2
Major Features ....................................................................................................................... E-4
Table of Contents ................................................................................................................... E-5
Checking the Supplied Accessories .................................................................................... E-7
Names of the Main Unit Parts ............................................................................................... E-9
Names of the Remote Control Parts ................................................................................... E-11
Preparing the Remote Control ............................................................................................ E-12
Button Battery Replacement ..................................................................................... E-12
Remote Control Range ............................................................................................. E-12
The Procedure Up to Projecting to the Screen ................................................................. E-13
Placement Guide .................................................................................................................. E-14
V3-131 Screen Size and Projection Distance ........................................................... E-14
V3-111 Screen Size and Projection Distance ........................................................... E-15
Connecting Personal Computers and Video Equipment .................................................. E-17
Connections with Personal Computer ....................................................................... E-17
Connect the projector’s RBG connector using the included RGB signal cable. .. E-17
To Output the External Output Signal of a Notebook Computer ......................... E-18
Connections with Composite Signals ........................................................................ E-19
Video Equipment with VIDEO Connectors .......................................................... E-19
Video Equipment with S-VIDEO Connectors ...................................................... E-19
Connections with Component Signals ....................................................................... E-20
When the Video Equipment Has a YCbCr Connector or YPbPr Connector ........ E-20
Connections with the AUDIO Jack ............................................................................ E-21
Power Cable Connections and Switching the Power On/Off ........................................... E-22
Operating ................................................................................................................... E-22
Finishing .................................................................................................................... E-24
Adjustment of the Projection Screen ................................................................................. E-25
Adjustment of the Projection Screen ......................................................................... E-25
Making Adjustments with the Adjusters .............................................................. E-26
General Operation ................................................................................................................ E-27
Input Selection .......................................................................................................... E-27
Automatic Adjustment ............................................................................................... E-27
Selection of Aspect Ratio .......................................................................................... E-28
Freezing a Moving Picture ......................................................................................... E-29
Cancelling Video and Audio Temporarily ................................................................... E-29
Lamp Mode ............................................................................................................... E-29
Keystone .................................................................................................................... E-30
Adjustment of the Volume .......................................................................................... E-30
Enlargement of the Image and Video Movement ...................................................... E-31
Using the Presentation Timer .................................................................................... E-32
Protecting the Projector with the Security Lock ......................................................... E-33
Using the Quick Menu ............................................................................................... E-35
Menu Operation Method ...................................................................................................... E-36
Performing Menu Operations .................................................................................... E-38
List of Item Names Offering Input Selection and Adjustments/Settings .................... E-41
Image ..................................................................................................................................... E-43
Brightness / Contrast / Color / Tint / Sharpness ........................................................ E-43
Picture Adj. / Fine Picture / H Position / V Position .................................................... E-43
Reset ......................................................................................................................... E-44
Color ...................................................................................................................................... E-45
Quick Color Adj. ........................................................................................................ E-45
Gamma ..................................................................................................................... E-45
Color Temp. ............................................................................................................... E-46
White ......................................................................................................................... E-46
Color Space .............................................................................................................. E-46
White Balance ........................................................................................................... E-47
E-5
Table of Contents
View .......................................................................................................................................
Aspect .......................................................................................................................
Filter ..........................................................................................................................
Vertical Flip ................................................................................................................
Keystone ....................................................................................................................
Keystone Save ..........................................................................................................
Setup .....................................................................................................................................
Auto Source ...............................................................................................................
Auto Power Off ..........................................................................................................
Menu Position ............................................................................................................
Lamp Mode ...............................................................................................................
Input Format ..............................................................................................................
Presentation Timer ....................................................................................................
Option ...................................................................................................................................
Language ..................................................................................................................
On Screen .................................................................................................................
Background ...............................................................................................................
Startup Screen ..........................................................................................................
Security Lock .............................................................................................................
Info. ........................................................................................................................................
Status ........................................................................................................................
Factory Default ..........................................................................................................
Lamp Timer Reset .....................................................................................................
Resolution / Frequency .............................................................................................
Lamp Timer ...............................................................................................................
When an Indicator is Lit or Flashing ..................................................................................
Troubleshooting ...................................................................................................................
Cleaning ................................................................................................................................
Replacing the Lamp Cartridge ............................................................................................
Specifications .......................................................................................................................
Table of Supported Frequency ...........................................................................................
Cabinet Dimensions ............................................................................................................
E-6
E-48
E-48
E-48
E-49
E-49
E-49
E-50
E-50
E-50
E-51
E-51
E-52
E-52
E-53
E-53
E-53
E-53
E-54
E-54
E-55
E-55
E-55
E-55
E-56
E-56
E-57
E-59
E-60
E-61
E-64
E-65
E-66
Checking the Supplied Accessories
Remove the main unit and the accessories from the box and check that the following items are included.
Storage case [1], Cable case [1]
These cases are designed to hold the projector itself and its
accessories.
Use them when storing the projector.
M
O
O
Z
S
A
2
L
O
V
O
C
E
Q
E
Z
E
E
R
F
Y
B
D
N
TA
S
B
G
R
O
E
ID
V
C
N
A
C
L
E
R
E
T
N
E
U
N
E
M
1
E
T
U
M
Q
U
K
IC
K
3
N
T
S
T
U
A
O
4
E
P
T
C
R
E
IM
T
Wireless remote control unit
(includes one button battery) [1]
This controls the projector. Please remove the transportation
insulation sheet at time of purchase. (See Page E-12.)
Y
B
D
N
TA
S
S
TU
TA
S
Y
B
D
N
TA
S
H
S
U
P
Storage case
L
VO
ZE
EE
FR
U
EN
M
EL
NC
CA
Y
DB
AN
ST
B
RG
O
DE
VI
R
TE
EN
1
E
UT
M
2
K
IC
QU
Q
O
EC
3
TN
KS
TO
AU
4
OM
ZO
CT
PE
AS
ER
M
TI
RGB signal cable
(Mini D-sub 15-pin, 2 m / 6.6 feet) [1]
This is used in making connections with a personal computer.
See Page E-17 about connections.
No. 773711000
Cable case
User’s Manual (CD-ROM edition) [1]
User’s Manual (Simplified Edition) [1]
E-7
E
C
R
U
O
S
HOW TO PUT THE PROJECTOR INTO THE STORAGE CASE
Lower the projector’s lens unit and close the lens shutter
before storing the projector in the case. See Page E-9.
Place the accessories in the cable case.
TO
U
A
Power cable (1.8 m / 5.9 feet) [1]
This power cable supplies power to the unit. See Page E-22
about connections.
Checking the Supplied Accessories
Expendables and Options
V3 Series lamps
Model V3-120 (ordering code: 28-051)
“WARNING”
Handling the cables supplied with this product, will
expose you to lead, a chemical known to the State of
California to cause birth defects or other reproductive harm.
Wash hands after handling.
E-8
Names of the Main Unit Parts
Lift button
S
TA
N
D
B
Y
S
S
TA
N
TA
D
B
TU
Y
S
A
U
TO
S
O
U
R
C
E
Ventilation holes
P
U
S
H
Lens unit
Exhaust vents
Ventilation slots
Lens shutter
Focus ring [E-25]
Lens
Remote control
sensor [E-12]
Adjuster button [E-26]
(Also on opposite side)
Handling the Lens Unit
C
When storing the projector
햲 Press on the top surface of the lens unit to lower it until
you feel it click.
햳 Slide the lens shutter to the right to close it.
R
U
O
S
TO
A
U
S
Y
D
B
TU
TA
N
TA
S
S
Y
B
D
U
P
TA
S
P
S
U
H
S
H
N
TA
S
B
D
Y
1
2
N
S
S
TA
TA
B
D
N
Y
S
TU
S
A
TO
U
E
C
R
U
O
When using the projector
햲 Slide the lens shutter to the left until it stops.
햳 Press the lift button (marked “PUSH”).
The lens unit rises and projecting is now possible.
2
1
Rear adjusters [E-26]
Speaker
Ventilation slots
Front adjusters [E-26]
Lamp cover [E-62]
E-9
Names of the Main Unit Parts
STANDBY indicator [E-22, 57]
STANDBY
STATUS
STATUS indicator [E-29, 57]
STANDBY button [E-22]
STANDBY
AUTO button [E-27]
AUTO
SOURCE button [E-27]
SOURCE
P
Remote control sensor [E-12]
U
S
H
S
TA
N
D
B
Y
S
S
TA
TA
N
B
S
Y
TU
D
A
AC IN connector [E-22]
U
TO
S
O
U
R
C
E
IO
D
AU
EO
D
VI
SEO
D
VI
B
G
R
Ventilation slot
Ventilation slots
Built-in security slot
(See description below.)
RGB connector [E-17, 20]
AUDIO S-VIDEO
VIDEO
RGB
VIDEO connector [E-19]
S-VIDEO connector [E-19]
AUDIO connector [E-21]
Built-in Security Slot
This security slot supports the MicroSaver Security System manufactured by
Kensington Microware Inc.
E-10
Infrared transmitter [E-12]
STANDBY button [E-22, 24]
This button is used to switch ON
the power and set the unit to the
STANDBY mode.
Buttons used for input selection
[E-27]
RGB button and VIDEO button
(VIDEO / S-VIDEO)
MUTE button [E-29]
(Temporarily cancels the video and
audio)
Number buttons [E-33]
(Used for the security lock.)
O
V
E
Y
B
D
N
TA
S
R
B
G
V
ID
E
O
C
A
N
C
E
L
R
F
E
R
E
T
E
N
E
M
N
U
E
Z
1
M
U
E
T
U
Q
2
L
E
IC
K
Q
C
O
K
S
3
N
T
A
U
O
T
A
4
S
P
M
O
O
Z
E
C
T
E
IM
T
R
Names of the Remote Control Parts
Buttons used for menu operations
[E-36]
and
buttons are
The , ,
the select (왖, 왔, 왗 and 왘) buttons.
STANDBY
MENU
VIDEO
QUICK button [E-35]
(Displays a simplified menu)
ENTER
RGB
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ECO button [E-29]
(Selection of lamp mode)
AUTO button [E-27]
(Automatic adjustment of the RGB
moving image)
ASPECT
FREEZE button [E-29]
(Freezes moving pictures)
VOL
KSTN
ZOOM
VOL button [E-30]
(Volume adjustment)
TIMER
ASPECT button [E-28]
(Selects the vertical and horizontal
ratio of the screen)
TIMER button [E-32]
(Presentation timer time setting
display)
KSTN button [E-30]
(Keystone correction adjustment)
ZOOM button [E-31]
(Digital zoom adjustment)
Precautions
Handling of the Remote Control
* Do not drop the remote control or handle it inappropriately.
* Do not expose the remote control to water or other liquids. Should the remote control become wet, wipe it dry
immediately.
* Try to avoid use in hot and/or humid locations.
* Please keep button battery out of the reach of children. If a battery is swallowed, promptly obtain the medical care of
a doctor.
* Remove the battery from the remote control when it is not going to be used for a long period.
* Some operations (such as menu operations) are available only through the use of the remote control and attention
should be given to its careful handling.
E-11
Preparing the Remote Control
Button Battery Replacement
Using the remote control for the first time
The battery compartment is fitted with a transportation insulation sheet at the time of shipping. Pull
out the sheet and remove it. The remote control is now ready for use.
Replacement Method
With the knob pressed to
the old battery and inthe battery holder into the re1 (A)
2 Remove
3 Insert
the right side, (B) draw out the
stall a new button battery with (+)
mote control and push in until the
side facing upward in the battery
holder.
battery holder closes with a “click”
sound.
2
0
2
5
battery case.
C
C
R
2
0
2
5
R
CR2
025
(B)
(A)
Purchase a CR2025 type battery for replacement.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type (CR2025) recommended by the manufacturer.
Dispose of used batteries according to your local regulations.
Remote Control Range
Point the infrared transmitter of the remote control toward the remote control sensor located at the front or rear of the main unit
and operate.
Reception of the remote control signal should generally be possible within the range illustrated below.
4m
/13
.1
Remote control
sensor
30°
fee
t
30°
10°
30°
Side View
Remote control infrared transmitter
7m/23.0 feet
1
3.
/1
4m
et
fe
50°
Remote control infrared transmitter
50°
7m/23.0 feet
Remote control sensor
Top View
Note
* Exposure of the main unit's remote control sensor or the remote control infrared transmitter to bright light or the obstruction of the signal
by an obstacle located in the pathway may prevent operation.
* The remote control will not function when the battery is exhausted.
E-12
The Procedure Up to Projecting to the Screen
Perform setup adjustments in the following order.
1 Position the projector
Determine the locations to set up the screen and the projector.
See “Placement Guide” on Page E-14.
2 Connect the video equipment and personal computer
Connect your equipment to the projector.
When making connections with the personal computer’s RGB connector, see “Connections with
Personal Computer” on Page E-17.
When making connections with the video equipment’s video connector or an S-video connector,
see “Connections with Composite Signals” on Page E-19.
When making connections with the video equipment’s YCbCr connector or YPbPr connector,
see “Connections with Component Signals” on Page E-20.
When playing the audio through the built-in speaker of the projector, see “Connections with the
AUDIO Jack” on Page E-21.
3 Connect the power cord, open the lens shutter and raise the lens unit.
See “Operating” on Page E-22.
See “Finishing” on Page E-24.
4 When selecting the language of menu displays, etc.
(Only when the power is first switched on following purchase)
See “When [Menu Language Select] is Displayed Upon Switching On the Power” on Page E-23.
5 Switching on the power of the personal computer and video equipment
6 Properly adjust the projection image to the screen
See “Adjustment of the Projection Screen” on Page E-25.
7 Selecting input equipment
See “Input Selection” on Page E-27.
8 Adjust the screen or video image
Adjust the image to the optimum condition as required.
See the Table of Contents for the adjustment items.
About DLP projectors
Though careful attention is paid to providing optimum quality, please note that with DLP type projectors, in rare cases there may
be black spots or bright spots among the picture elements.
Note:
* Please purchase a screen.
* A component cable (order code 28-690), which is available separately, is required to connect a DVD player or other equipment with YCbCr
connectors.
* A component cable (order code 28-690), which is available separately, is required to connect high definition (HD) video equipment or other
equipment with YPbPr connectors.
E-13
Placement Guide
• Use this information as a guide to find out about the screen size when the projector is placed at a certain location, or
to find out the approximate size of a screen that will be required.
• Refer to the projection distance table for your projector model.
• When installing the projector on its back, change the projection method. See “Vertical Flip” on page E-49.
V3-131 Screen Size and Projection Distance
• The projection distance over which focussing is adjustable is 1.20 m (3.94 feet) to 10.00 m (32.81 feet). The projector
should be placed within this range.
Screen Size Designation (Inches)
30
0"
Height from center of
lens to top edge of
the projection
25
0"
20
0"
18
0"
h1
Height from center of
lens to bottom edge
of the projection
15
0"
12
0"
h2
10
0"
80
"
40
60
"
"
36
Unit: m (feet)
0(
.0
10
33
7.
(2
33
Width
8.
(3 1.2
.9 0
4
(4 1.3 )
.3 3
6
2.
00 )
(6
.5
6)
2.
67
(8
.
3. 76
33 )
(1
0.
93
4.
)
00
(1
3.
12
)
5.
00
(1
6.
40
)
6.
00
(1
9.
69
6.
67 )
(2
1.
88
)
)
32
.8
1)
"
Lens surface of
the main unit
Screen size (Diagonal)
Screen Size
Designation (Inches)
36"
40"
60"
80"
100"
120"
150"
180"
200"
250"
300"
Screen Size Width x Height
(m)
(feet)
0.73⳯0.55
0.81⳯0.61
1.22⳯0.91
1.63⳯1.22
2.03⳯1.52
2.44⳯1.83
3.05⳯2.29
3.66⳯2.74
4.06⳯3.05
5.08⳯3.81
6.10⳯4.57
2.40 ⳯ 1.80
2.67 ⳯ 2.00
4.00 ⳯ 3.00
5.33 ⳯ 4.00
6.67 ⳯ 5.00
8.00 ⳯ 6.00
10.00 ⳯ 7.50
12.00 ⳯ 9.00
13.33 ⳯10.00
16.67 ⳯12.50
20.00 ⳯15.00
Projection Distance
(m)
(feet)
1.20
1.33
2.00
2.67
3.33
4.00
5.00
6.00
6.67
8.33
10.00
3.94
4.36
6.56
8.76
10.93
13.12
16.40
19.69
21.88
27.33
32.81
Height h1
(m)
(feet)
0.65
0.72
1.07
1.44
1.79
2.15
2.69
3.22
3.59
4.48
5.38
2.13
2.36
3.51
4.72
5.87
7.05
8.83
10.56
11.78
14.70
17.65
Height h2
(m)
(feet)
0.10
0.11
0.16
0.22
0.27
0.32
0.40
0.48
0.54
0.67
0.81
0.33
0.36
0.52
0.72
0.89
1.05
1.31
1.57
1.77
2.20
2.66
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the projector be in a horizontal condition
(with front and rear adjusters fully withdrawn).
E-14
Height
Placement Guide
V3-111 Screen Size and Projection Distance
• The projection distance over which focussing is adjustable is 1.20 m (3.94 feet) to 12.82 m (42.06 feet). The projector
should be placed within this range.
Screen Size Designation (Inches)
30
0"
Height from center of
lens to top edge of
the projection
25
0"
20
0"
h1
18
0"
15
Height from center of
lens to bottom edge
of the projection
0"
h2
12
0"
10
0"
80
"
60
4)
12
Unit: m (feet)
10
8.
55
(2
69
(2
5.
)
03
7.
1.
(2
)
41
6.
6.
13
(1
4.
5.
(1
1.
27
4.
(1
42
83
)
01
)
22
0)
.4
(8
3.
56
2.
(3 1.2
.9 0
4)
(5 1.7
1
.6
1)
8.
23
)
05
)
"
.6
8(
35
.0
"
28
.8
2(
42
.0
6)
"
40
Lens surface of
the main unit
Width
Screen size (Diagonal)
Screen Size
Designation (Inches)
28"
40"
60"
80"
100"
120"
150"
180"
200"
250"
300"
Screen Size Width x Height
(m)
(feet)
0.57⳯0.43
0.81⳯0.61
1.22⳯0.91
1.63⳯1.22
2.03⳯1.52
2.44⳯1.83
3.05⳯2.29
3.66⳯2.74
4.06⳯3.05
5.08⳯3.81
6.10⳯4.57
1.87 ⳯ 1.40
2.67 ⳯ 2.00
4.00 ⳯ 3.00
5.33 ⳯ 4.00
6.67 ⳯ 5.00
8.00 ⳯ 6.00
10.00 ⳯ 7.50
12.00 ⳯ 9.00
13.33 ⳯10.00
16.67 ⳯12.50
20.00 ⳯15.00
Projection Distance
(m)
(feet)
1.20
1.71
2.56
3.42
4.27
5.13
6.41
7.69
8.55
10.68
12.82
3.94
5.61
8.40
11.22
14.01
16.83
21.03
25.23
28.05
35.04
42.06
Height h1
(m)
(feet)
0.59
0.83
1.25
1.67
2.08
2.50
3.13
3.75
4.17
5.21
6.25
1.94
2.72
4.10
5.48
6.82
8.20
10.27
12.30
13.68
17.09
20.51
Height h2
(m)
(feet)
0.16
0.22
0.34
0.45
0.56
0.67
0.84
1.01
1.12
1.40
1.68
0.52
0.72
1.12
1.48
1.84
2.20
2.76
3.31
3.67
4.59
5.51
* There is a tolerance of ±5% due to design values.
* This table uses the lens apex and lens center as references and requires that the projector be in a horizontal condition
(with front and rear adjusters fully withdrawn).
E-15
Height
Placement Guide
Installation Height of Projection Screen [Reference]
Once the installation location and position have been decided, the projection height should be checked. In the case of large
screen sizes, there are instances where the image cannot be projected within the floor to ceiling height.
The required installation height can be found using the following formula:
[Height from center of lens to top edge of the projection(h1)] m (feet) + 0.03m (0.1 feet) + Stand height
Example:
Using a 150" 4:3 screen and placing the projector horizontally, the required installation height will be
3.13m (10.3 feet) + 0.03m (0.1 feet) = 3.16m (10.4 feet) (without a stand)
An installation room with a height of 2.4m (7.9 feet) will have insufficient room height even when the projector is placed on the
floor. (The rear adjusters can be extended to lower the projected image.)
Screen size vertical
dimension
Lens center
Approx. 0.03m (0.1feet)
Stand dimension
E-16
Screen size top edge
dimension measured
from floor
Connecting Personal Computers and Video Equipment
Connecting this unit with a personal computer permits presentation data to be projected as a large screen display at
conferences, lectures, and on other occasions. Furthermore, connecting this unit to a DVD player or other video equipment source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home
theater.
Connections with Personal Computer
Please check the following before making connections with the personal computer.
• A suitable resolution for the V3-111 is 800 ⳯ 600 dots (S-VGA) and the maximum displayable resolution is XGA (1024 ⳯ 768
dots).
• A suitable resolution for the V3-131 is 1024 ⳯ 768 dots (XGA) and the maximum displayable resolution is S-XGA (1280 ⳯
1024 dots).
Make changes to a displayable resolution at the personal computer side. Please check with “Table of Supported Frequency” on
Page E-65.
• The setting method for the personal computer will differ depending on the specific model. Please read the personal computer
instruction manual or the on-line help information, or contact the manufacturer of your personal computer.
Connect the projector’s RBG connector using the included RGB signal cable.
•
•
When making connections with the RGB connector of the projector, please make the connection via the supplied RGB signal
cable.
The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “RGB”
using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-52.
MONITOR OUT
Personal
computer
RGB signal cable (Supplied item)
Note:
* Before making connections, check the power of the projector and the equipment to be connected is switched off.
* When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook computer
startup procedure as well as the operation that follows startup. Please consult the instruction manual of your notebook computer or the online help.
E-17
Connecting Personal Computers and Video Equipment
To Output the External Output Signal of a Notebook Computer
When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook
computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your
notebook computer or the on-line help while performing the following procedure.
whether a signal is being sent from the notebook computer to the projector.
1 Check
An indication appearing on the liquid crystal display of the notebook computer does not necessarily mean that an external
output signal is being output.
REFERENCE: When “Resolution” or “Frequency” is not displayed under “Info.” on the menu of the projector, this means that
the external output signal is not being output from the personal computer. See “Resolution/Frequency” on Page E-56.
a sign not be output from the notebook computer, please try the operation described below.
2 Should
For an IBM PC/AT compatible computer, press the [Fn] key plus any one of the [F1] to [F12] keys. (See the table below.)
Manufacturer
akia
COMPAQ
DELL
EPSON
FUJITSU
GATEWAY
iiyama
IBM
NEC
Panasonic
SHARP
SONY
SOTEC
TOSHIBA
Victor
Model
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
All computers
Key
Fn + F2
Fn + F4
Fn + F8
Fn + F8
Fn + F10
Fn + F3
Fn + F3
Fn + F7
Fn + F3
Fn + F3
Fn + F5
Fn + F7
Fn + F3
Fn + F5
Fn + F10
Note: Table information is current to September 2002.
Note:
When the liquid crystal display of the notebook computer and the projector are displayed at the same time, the projected image might not be
correct even though the liquid crystal display shows a correct indication. Should this occur, stop the simultaneous display of the notebook
computer and try the mode with external output only. Try an operation such as that described in aforementioned Step 2 and try closing the
liquid crystal panel which might result in external output only.
E-18
Connecting Personal Computers and Video Equipment
Connections with Composite Signals
Video Equipment with VIDEO Connectors
• Connect to the projector’s VIDEO connector using a commercially available video cable.
• The input setting of the VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project, please
change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input Format]
→ [Video].
See “Input Format” on Page E-52.
Video Equipment with S-VIDEO Connectors
• Connect to the projector’s S-VIDEO connector using a commercially available S-Video cable.
• The input setting of the S-VIDEO connector has been set to “Auto” at the factory; however, if the projector does not project,
please change the input setting to “Your Country’s Television Broadcast System” using the menu sequence of [Setup] → [Input
format] → [S-Video].
See “Input Format” on Page E-52.
Video deck, DVD player, document
camera, etc.
VIDEO
Video cable (RCA pin plug)
(Commercially available)
S-Video cable (Mini DIN 4-pin plug)
(Commercially available)
E-19
S-VIDEO
Connecting Personal Computers and Video Equipment
Connections with Component Signals
When the Video Equipment Has a YCbCr Connector or YPbPr Connector
• The projector has been set to “Auto” at the factory; however, if it does not project, please change the input setting to “Component” using the menu sequence of [Setup] → [Input Format] → [RGB].
See “Input Format” on Page E-52.
• When projecting the YCbCr signal or YPbPr signal, if the color of the overall image strongly leans toward being greenish or
another color, change the setting under the menu of [Color] → [Color Space].
See “Color Space” on Page E-46.
Component cable (Available as an option)
(Mini D-sub 15-pin to RCA⳯3)
(Order code: 28-690)
Green
Blue
Red
Y
Cb
Cr
COMPONENT
COMPONENT
Y
Pb
Pr
Green
Component cable (Available as an option)
(Mini D-sub 15-pin to RCA⳯3)
(Order code: 28-690)
Blue
Red
E-20
Connecting Personal Computers and Video Equipment
Connections with the AUDIO Jack
* Connect to the projector’s AUDIO jack using a commercially available audio cable. If the other device has an RCA phono type
audio jack, connect via a commercially available audio converter cable.
* The built-in speaker of the projector provides monaural audio. To enjoy convincing audio reproduction, please connect the
audio output of the video equipment to your audio system.
* The built-in speaker outputs the audio of the equipment connected to the AUDIO jack.
Audio cable (Mini plug)
(Commercially available)
White
AUDIO OUT
L
Audio conversion cable
(Mini-jack/ RCA pin plug)
(Commercially available)
Audio cable (Mini plug)
(Commercially available)
E-21
R
Red
Power Cable Connections and Switching the Power On/Off
There is an order in which the power cable is connected and the power is switched on/off.
Operating
1 Connect the AC IN connector of the projector and the power outlet using the supplied power cable.
The STANDBY indicator will light in amber, and the unit will enter the standby mode.
ST
STANDBY
PU
SH
ST
STATUS
AN
DB
AT
US
To wall outlet
Y
ST
AN
Y
DB
AU
TO
UR
CE
R
G
B
SO
S
TA
N
D
B
Y
S
S
TA
N
TA
D
B
TU
Y
S
A
U
TO
S
O
U
R
C
E
AU
D
IO
S-
VID
EO
VID
EO
Lit amber
Firmly plug in all the
way.
P
U
S
H
2 햲 Slide the lens shutter to the left until it stops.
2
햳 Press the lift button (marked “PUSH”).
The lens unit rises and projecting is now possible.
1
3 Switch on the projector power
Press the STANDBY button.
STANDBY
(button on main unit)
STANDBY
MENU
ENTER
RGB
Note:
The power will not turn on unless the lens unit is raised.
If the STANDBY button is pressed when the lens is stowed away, the
STATUS and STANDBY indicator’s flash orange for several seconds to
notify you that the lens is not raised.
The first time the power is switched on after purchase, [Menu
Language Select] will be displayed. See Page E-23 for information about language selection.
• When the power is turned on, the STANDBY indicator starts
flashing green, then stops flashing after about 60 seconds. If
the STATUS indicator lights green at this time, the lamp mode
is set to “Eco”. See E-29 and 51 for instructions on selecting.
• If the power does not come on, see “When the STATUS Indicator is Lit or Flashing” on Page E-57.
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
This indicator is also lit green in Eco-mode.
STANDBY
STATUS
Lit amber
STANDBY
STATUS
Flashing green
(Approximately 60
seconds)
STANDBY
STATUS
Lit green
Power is on
If the “Password” input window is displayed: See E-34.
A password is set for this projector.
The projector cannot be used unless the correct password is input.
To turn off the power: See E-24.
The projector is now capable of regular projection.
4 Switch on the power of the connected equipment
Note:
• When the power plug will be unplugged from the power outlet, please place the projector near the power outlet so that it may be reached
easily.
• Press the STANDBY button after the STANDBY indicator is lit in amber.
E-22
Power Cable Connections and Switching the Power On/Off
When [Menu Language Select] is Displayed Upon Switching On the Power
The first time the power is switched on after purchase, [Menu Language Select] will be displayed. Follow the procedure described below and select the display language of the projector.
If the image is blurred, turn the focus ring counterclockwise or clockwise to focus it. See Page E-25.
Cursor
1 Press the SELECT 왖왔 buttons of the Remote control and align the deep blue cursor with [English].
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
2 Press the ENTER button to set.
This will set the language and [Menu Language Select] will close.
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
This completes the selection of the display language.
Caution:
[Menu Language Select] will not appear the next time the power is switched on.
Should a change of language become necessary, see “Language” on Page E-53.
E-23
Power Cable Connections and Switching the Power On/Off
Finishing
1 Switch off the power of the connected equipment
2 Switch off the power of the projector
Press the STANDBY button.
STANDBY
MENU
ENTER
RGB
STANDBY
CANCEL
VIDEO
(button on main unit)
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
The [Power Off] display appears.
When the level gauge reaches maximum, the projection screen
will go off (in about 5 seconds) and the projector will enter the
power-off operation.
AUTO
4
ASPECT
Note:
Do not stow away the lens unit while projecting an image. Doing so
could damage the projector. If the lens unit has been stowed away
while projecting an image, the STATUS and STANDBY indicator’s flash
orange and the projector is automatically turned off.
Power Off
OK ?
Note:
* The operation can be cancelled by pressing a button other than the
STANDBY button.
* One more press of the STANDBY button will switch off the power.
The STANDBY indicator changes to flashing amber and lights a
steady amber after about 90 seconds (when the unit enters the
standby mode).
STANDBY
STATUS
Lit green
STANDBY
STATUS
Flashing amber
(Approximately 90
seconds)
STANDBY
STATUS
Lit amber
Standby mode
3 Unplug the power cable
C
E
Check that the STANDBY indicator is lit in amber and then
unplug the power cable.
The STANDBY indicator will go off when the power cable is unplugged.
B
D
P
U
S
H
S
TA
N
1
and the lens unit locks.
햳 Slide the lens shutter to the right to close it.
Y
S
S
TA
N
TA
D
B
TU
Y
S
A
U
TO
S
O
U
R
4 햲 Press down on the lens unit until a “click” is heard
2
Warrning
Do not unplug the power cable while the STANDBY indicator is flashing amber. Doing so may shorten the life of the lamp
or damage the projector.
E-24
Adjustment of the Projection Screen
Switch on the power of the connected equipment and make the adjustments with the video signal being input to the
projector.
Adjustment of the Projection Screen
1 Adjust the projection image to the screen.
Check that the screen is set level and vertically.
(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of
the projector lens.)
(2) If the image is shifted vertically, move the image up or down with the adjuster. See “Making Adjustments with the Adjusters” on Page E-26.
(3) If the image is slanted, adjust by turning the right or left adjuster. See “Making Adjustments with the Adjusters” on Page E26.
(4) A projection image such as that illustrated in the diagram is the result of the projector not being perpendicular to the
screen. Set the projector so that it is pointing straight toward the screen.
(5) If the image shows keystone distortion, adjust using remote control or menu operations. See “Keystone” on Page E-30, 49.
(2)
(3)
(4)
(1)
(4)
(3)
(5)
P
2 Turn the focus ring and adjust the focus of the screen
Focus ring
E-25
Adjustment of the Projection Screen
C
R
U
O
S
TO
U
A
Y
B
S
N
TA
S
D
TU
TA
S
Y
B
H
S
N
TA
S
D
(1)
U
P
Raising the projection image
While viewing the projection image, (1) press and hold
the front adjuster buttons located at the left and right and,
(2) raise the projector to align the image with the screen,
then release your fingers.
Turn the left and right front adjusters for fine adjustment.
Adjust so that there is no shaking of the projector.
E
Making Adjustments with the Adjusters
(2)
(1)
Adjuster button
Lowering the projection image
Use the procedure described above to lower the front
adjusters.
If the rear adjusters are turned to lift the rear, the projected image lowers.
Adjust so that there is no shaking of the projector.
P
U
S
H
S
TA
N
D
B
Y
S
S
TA
TA
N
B
S
Y
U
TO
O
U
R
C
E
EO
VID
SEO
VID
B
G
R
E-26
TU
D
A
S
IO
D
AU
Note:
When the projector has a rear installation is used, the orientation of the projection will need to be changed.
Please see “Vertical Flip” on Page E-49.
General Operation
This section describes the use of direct operation with the main unit or remote control buttons.
For information about operation using the menu, see “Menu Operation Method” on Page E-36 and the various items on
Pages E-43 to E-56.
Input Selection
This operation selects the input signal to be projected.
STANDBY
Main unit operation: Press the SOURCE button.
(It will not function while the menu or the quick menu is displayed.)
STATUS
STANDBY
When Auto Source is On
Whenever the SOURCE button is pressed, the projector automatically selects
another source that has the next input signal.
AUTO
SOURCE
When Auto Source is Off
The input selection condition used last time will be set.
Each press of the button moves the selection one step in the sequence of RGB →
VIDEO → S-VIDEO. Note that the various input signals will become the signal
type set with [Input Format] See “Input Format” on page E-52.
Remote control operation: Press the desired input selection button.
RGB button ........ Switches the RGB input.
VIDEO button ..... The input switches between VIDEO and S-VIDEO each time the button is
pressed.
STANDBY
MENU
ENTER
RGB
CANCEL
VIDEO
QUICK
Q
When Auto Source is On
When an input signal is not present at the selected source, the projector automatically selects the next source that has an input signal.
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
When Auto Source is Off
The projector switches to the selected source regardless of whether an input signal is present.
Note:
* When you do not operate source selection, the projector will assume the input selection condition that was previously used.
* See “Auto Source” on Page E-50 for information about the Auto Source on and off
conditions.
Automatic Adjustment
This function automatically adjusts the position shift, screen size, vertical stripes,
and color infidelity of the projected analog RGB input signal.
Normally automatic adjustment is performed at the time of signal selection.
STANDBY
STATUS
STANDBY
Main unit operation/Remote control operation: Press the AUTO button.
(This will not function while the menu or the quick menu is displayed.)
A press of the AUTO button starts the automatic adjustment.
AUTO
SOURCE
Note:
* If the display position is shifted, vertical lines appear on the picture, or the projection
is not good even after using automatic adjustment, please perform image adjustment
manually. See “Picture Adj. / Fine Picture / H Position / V Position” on Page E-43.
* When the image extends beyond the boundaries of the screen or is smaller than the
screen, set Aspect to “Auto”. See “Selection of Aspect Ratio” on Page E-28 and “Aspect” on Page E-48.
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
E-27
KSTN
ZOOM
TIMER
General Operation
Selection of Aspect Ratio
This function selects horizontal and vertical picture proportions of the input
signal.
STANDBY
MENU
ENTER
RGB
Press the ASPECT button while viewing the projected image and select the
aspect ratio.
VIDEO
CANCEL
QUICK
Q
Personal Computer Signal
Each press of the ASPECT button advances the selection one step in the sequence of Auto → Direct → Real, and then repeats.
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Auto ............ Automatically enlarges or reduces the image to project a full screen in a ratio
of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the maximum displayable
size
Real ............ Projects the input signal without pixel conversion.
Input Signal
Auto
Direct
Real
The setting is higher
than the display resolution of the projector.
The setting is lower
than the display resolution of the projector.
Video Signals / Component Signals
Each press of the ASPECT button advances the selection one step in the sequence of Auto → Wide → Zoom, and then repeats.
Auto ............ While maintaining the aspect ratio, projects a full screen so that no portions extend beyond the boundaries of the screen. The top
and bottom of the 16:9 image becomes black.
Wide ........... Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a proper aspect ratio.)
Zoom .......... Projects only the 4:3 portion within 16:9 image to fill the screen.
(Portion that extend off screen is cut.)
Aspect ratio selection
Auto
Wide
Zoom
4:3 screen
16:9 screen
Note:
When selection has been made for the “Real” setting of the personal computer signal (i.e., when the input signal and the projector display
resolution are high) and the “Zoom” setting of the video signal, pressing the SELECT 왖왔왗왘 buttons on the remote control will permit
movement of the display position. Note that there will not be any movement when the menu or the quick menu is displayed.
E-28
General Operation
Freezing a Moving Picture
This function is used to stop and view a moving picture. Note that the input
image continues to advance even though the picture there is a still picture
condition.
STANDBY
MENU
ENTER
RGB
CANCEL
VIDEO
QUICK
A press of the FREEZE button changes the screen to a still picture. A
further press returns the screen to a moving picture.
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Cancelling Video and Audio Temporarily
This function is used to cancel the video and audio at the same time.
STANDBY
A press of the MUTE button will blank the picture and the sound, and
the screen will take on the background color that has been set.
Another press will cause a return to the original conditions.
MENU
ENTER
RGB
CANCEL
VIDEO
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Lamp Mode
Use this if the picture is projected on a small screen and the picture
is too bright or when projecting images in dark rooms.
STATUS indicator
STANDBY
Pressing the ECO button will set the lamp mode.
Eco (STATUS indicator is lit green)
The lamp’s brightness is reduced to approximately 80%, extending the
lamp’s service life.
STANDBY
AUTO
SOURCE
Normal (STATUS indicator is off)
The lamp brightness is set to 100% and the screen is bright.
Note:
Frequent switching this mode can degrade the lamp.
STATUS
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
E-29
KSTN
ZOOM
TIMER
General Operation
Keystone
Use this to adjust for trapezoidal (keystone) distortion of the projected image.
STANDBY
MENU
ENTER
RGB
Adjustment Method
(1) Press the 왖 or 왔 KSTN button to make the left and right sides
parallel.
The keystone adjustment display appears when one of the buttons is
pressed.
VIDEO
QUICK
CANCEL
Q
(2)
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
(1)
Press the “왔” button.
Press the “왖” button.
(2) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
Note:
* Keystone adjustment values can be saved. See “Keystone Save” on Page E49.
* Screen examples have been drawn in an exaggerated style for the purpose
of description.
* Please note that depending on the projected picture and the projection conditions, it may not be possible to eliminate keystone distortion completely.
Adjustment of the Volume
This function adjusts the volume of the built-in speaker.
(1) Press the 왖 or 왔 VOL button to adjust the volume.
The volume adjustment display appears when one of the buttons is
pressed.
STANDBY
MENU
ENTER
RGB
VIDEO
QUICK
CANCEL
Q
(2)
The 왖 button increases the volume and the 왔 button decreases the
volume.
FREEZE
MUTE
ECO
1
2
3
E-30
4
ASPECT
VOL
(2) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
Note:
* Adjustment of the volume will not produce any sound unless an image is
being projected.
AUTO
(1)
KSTN
ZOOM
TIMER
General Operation
Enlargement of the Image and Video Movement
This function digitally enlarges the personal computer image and video
image.
STANDBY
MENU
ENTER
RGB
(1) Press the ZOOM button to enlarge the image.
The zoom display appears when the ZOOM button is pressed.
VIDEO
CANCEL
QUICK
(2)
Q
(3)
FREEZE
MUTE
ECO
AUTO
1
2
3
4
VOL
KSTN
ZOOM
ASPECT
TIMER
(1)
Each press of the 왖 button enlarges the image and each press of the
왔 button makes the image smaller (returning it to 1:1).
Zoom
0
(No enlargement)
Zoom
21
(Approximately 2 times enlargement)
(2) Pressing the SELECT 왖왔왗왘 buttons on the remote control at
the time of the zoom operation will cause the display position to
move.
(There will not be any movement when zoom is at 0.)
Zoom
21
(Approximately 2 times enlargement)
Zoom
21
(Movement)
(3) Press the CANCEL button to immediately close the display.
The display will close when there has not been an operation in about
10 seconds.
Note:
After magnifying the image, be sure to use the ZOOM button to bring the gauge
value back to “0”.
The image can also be moved in the following circumstances.
•
•
When “Aspect” is set to “Real” by the signal of the personal computer, and the input resolution is
higher than the display resolution of the projector.
When “Aspect” is set to “Zoom” by the video signal.
Note:
* Zoom and image movement functions are cancelled when the input is switched.
* The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected
so that they are not conspicuous.
* Movement of the screen will not be possible when the menu screen is being displayed.
E-31
General Operation
Using the Presentation Timer
The presentation is given while checking the timer displayed
on the screen.
The gauge display allows the remaining time to be known at
a glance.
(1) Press the TIMER button to show the settings display.
The display will close when an operation has not been made
for about 10 seconds.
STANDBY
MENU
(2)
ENTER
RGB
CANCEL button
(3)
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
(1)
[Timer settings display]
Press the CANCEL button to close the display immediately.
(2) Use the 왗 and 왘 SELECT buttons to set the time.
The setting contents are “Off” and from 10 to 60 minutes (in
10-minute intervals)
Settings can also be made with the SELECT 왗왘 buttons.
(3) Press the ENTER button and start the timer.
• The display of the timer setting will close, the display of the
timer will appear and simultaneously the timer will start.
Gauge (Blue)
[Timer Display]
The blue gauge indicates the remaining time. When the
gauge disappears,the time is up.
The gauge continues to be displayed when the timer is
stopped.
When the remaining time is
“0” (Gray)
• Press the ENTER button to restart the timer. The timer will
start with the same time setting.
• Press the CANCEL button to close the timer display. The
timer setting will return to “Off”.
Moving the Position of the Timer Display
The SELECT 왖왔왗왘 buttons on the remote control permit movement within the movable range of the timer display.
Movable Range of the Timer Display
Note:
* The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will
still be operating at such times. Also, the timer will not be displayed unless a signal is being input.
* While the presentation timer is being displayed, screen movement will not be possible in the zoom mode.
E-32
General Operation
Protecting the Projector with the Security Lock
A password can be registered and the security lock set in order to protect the projector from unauthorized use.
Registering the password
The password is registered using the menus. For instructions on operating the menus, see “Menu Operation Method” on E-36.
(1) Select “Security Lock” in the “Option” menu and set it to “Enable”.
The menu closes and the password registration display appears.
(2) Use the number buttons (1 to 4) to register the password.
Be sure to input a 4-digit number.
Example: Registering the password “2441”
(1) Press number button “2”. An “ ” (asterisk) appears at the first place.
Next press number buttons “4”, “4” and “1” in that order. Asterisks appear
in all four places.
*
STANDBY
MENU
ENTER
RGB
VIDEO
QUICK
CANCEL
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
(2) Input the password again. An “ ” appears when the input number
matches. If there is a mistake, the asterisks turn off. Start over from step
(1) above.
If the password matches, the password registration display closes.
*
Note:
To cancel the number you have input, press the CANCEL button.
The asterisks disappear and the display returns to the input standby mode at the first
place.
To cancel the password registration mode, press the CANCEL button again. The “Password” display turns off.
This completes password registration.
The “Password” input display appears the next time the power is turned
on.
Note:
The numbers you have input are not displayed. Be sure to write down the password
and store it in a safe place.
E-33
KSTN
ZOOM
TIMER
General Operation
If the password input display appears when the power is turned on
When a password has been registered, the “Password” input window appears on the projected image when the power is turned
on. The projector continues projecting this image until the correct password is input. At this time, only the STANDBY button (power
off) works. Use the procedure described below to input the registered password. For instructions on registering the password, see
E-33.
Input the password using the number buttons (1 to 4).
Be sure to input the registered 4-digit number.
Example: To input the password “2441”
Press number button “2”. An “ ” (asterisk) appears at the first place.
*
Next press number buttons “4”, “4” and “1” in that order. Asterisks appear in all
four places.
If the password matches, the window turns off and the projector can be used
normally.
[Password input window]
Canceling the password/Changing the password
The password is canceled and changed using the menus. For instructions on operating the menus, see “Menu Operation Method”
on E-36.
Canceling the password
Select “Security Lock” in the “Option” menu and set it to “Disable”.
This clears the password and disables the security lock.
The password input display no longer appears when the power is turned on.
Changing the password
After setting “Security Lock” to “Disable” as described above, set it back to “Enable”. The menu closes and the password registration display appears.
Register the new password. See “Registering the password” on E-33.
E-34
General Operation
Using the Quick Menu
This function permits frequently used adjustments to be
performed quickly.
Note that the Quick Menu will not be displayed unless the signal
of the connected equipment is input. Please select the input that
you wish to adjust.
(1) A press of the QUICK MENU button brings up the quick
adjustment display.
Further presses cause the adjustment display to change in
sequence.
The adjustment display can be selected with use of either the
SELECT 왖 or 왔 button.
STANDBY
VIDEO
QUICK
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
Content of Adjustments and Settings
Example: Brightness adjustment display
Adjustment/Setting
Brightness
Adjusts the brightness of the image. See page E-43.
Contrast
Adjusts the contrast of the image. See page E-43.
Keystone
Corrects (vertical) keystone distortion of the screen. See page E-30.
Volume
This function adjusts the volume of the built-in speaker. See page E-30.
Presentation timer
Sets the time of the presentation timer. See page E-32.
Quick Color Adj.
Select the preset color mode. See page E-45.
E-35
CANCEL
Q
(2) Press the cursor 왗 or 왘 button to make the adjustment.
(3) To close the display immediately, press the CANCEL button.
In the absence of operations for a period of about 10 seconds, the display will close automatically.
Display Item
MENU
ENTER
RGB
KSTN
ZOOM
TIMER
(2)
(1)
(3)
Menu Operation Method
• This section describes only the menu operation method. Please see this item should you need information while
performing menu operations.
• For information about a menu function, adjustment, or setting, please see one of the pages containing such descriptions.
• Adjustments and settings are made by projecting an image and adjusting to an optimum condition.
• The remote control should be pointed toward the remote control sensor of the projector and operated.
• To return the various items that have been changed via the menu to their standard values (i.e., default values at time
of shipping from the factory), see “Factory Default” on Page E-55. (Some items will not return to their initial values.)
• The adjustment/setting items and contents will differ depending on the input selection and the adjustment/setting
items that can be used with the input signal are displayed on the menu.
Names and functions of remote control unit buttons used for menu operations
STANDBY
MENU
VIDEO
MENU button
Used for menu display and menu closure.
ENTER
RGB
QUICK
CANCEL
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
SELECT 왖왔왗왘 buttons
Used in the selection of menu names and item names as
well as in setting and adjusting the item contents.
ENTER button
Used to enter settings.
TIMER
CANCEL button
Used to return to menu name selection as well as to close
the menu (and the sub menu display).
E-36
Menu Operation Method
Menu Screen Names and Functions
Menu Name
This is the title of the menu.
There is a change to the title screen
when the menu is selected.
The cursor moves to the selected menu
name.
Cursor (Deep Blue)
This permits setting/adjustment of the
item located at the cursor position.
Item Name
This is the name of the adjustment or setting.
Icon: Pressing the ENTER button displays the sub menu or setting contents.
Adjustment Bar and Settings Contents
Adjustment Bar: The increases and decreases in bar length express the adjustment condition.
Setting Contents: Displays the contents that have been set.
Sub menu
Adjustment Bar
Item Name
E-37
Settings Contents
Menu Operation Method
Performing Menu Operations
• Only “Setup”, “Options” and “Info.” can be selected when no signal is being input.
• The menu display will close if, after pressing a button, the next button operation is not made within 30 seconds.
• The adjustment and the setting values are stored even when the power is switched off or the plug is disconnected
from the power outlet.
(Note that some items are not stored.)
Preparation
Switch on the power of the connected equipment, start the play operation or another operation, and input
the signal to the projector.
Select the input that you wish to adjust.
The menu display of the description diagram depicts an example in which the “Keystone” item name is selected.
Menu Display
1
Press the MENU button to display the menu
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
The menu name that existed when the menu was closed previously will be displayed.
Selection of the Menu Name
2
Press the SELECT 왗왘 button to select the menu name
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Each press of the SELECT 왘 button advances the selection one step in the sequence of “Color” → “View” → “Setup” →
“Option” → “Info.” → “Image”. Each press of the SELECT 왗 button causes a return of one step.
The cursor moves to the selected menu name.
Note:
Please check that the cursor of the item name has disappeared at the time of menu name selection.
Press the CANCEL button to make the cursor disappear.
E-38
Menu Operation Method
Displaying the Cursor
3
Press the 왔 SELECT button to display the item name selection cursor.
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
This condition allows selection of the
item name.
Selection of the Item Name
4
Press the SELECT 왖왔 button to align the cursor with the item name
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Items for which the Icon Is Displayed
Press the ENTER button to display the submenu.
Press the SELECT 왖왔 button and align the cursor with the desired item name.
There are also some items for which the setting display or the verification display will appear. Please see the various item
descriptions.
STANDBY
MENU
VIDEO
Sub menu
ENTER
RGB
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Making Adjustments/Settings
5
Press the SELECT 왗왘 button and make the adjustment (or setting) while viewing the image
When a button is pressed, the image will also change.
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Adjustment display: Each press of the button results in a change of 1 point and continued presses
cause changes to proceed in order.
Setting display: The setting contents display changes with each press of the button.
E-39
Menu Operation Method
Closing the Menu
6
Press the MENU button and close the menu display
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Selecting Another Menu Name with Remote Control Operation
When a sub menu is displayed, press the CANCEL button and close the sub menu.
Press the CANCEL button again to turn off the item name
cursor.
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Press the SELECT 왗왘 button and select the menu name.
(Menu names cannot be selected when the item name
cursor is displayed.)
STANDBY
MENU
ENTER
RGB
VIDEO
CANCEL
QUICK
Q
FREEZE
MUTE
ECO
1
2
3
AUTO
4
ASPECT
VOL
KSTN
ZOOM
TIMER
Note:
A press of the QUICK button while the menu is displayed will close the menu and display the quick menu. A press of the MENU button while
the quick menu is displayed will close the quick menu and display the menu.
E-40
Menu Operation Method
List of Item Names Offering Input Selection and Adjustments/Settings
The item names that can be adjusted/set will differ depending on the input signal.
u
om t Si
gn
R pon al
G
B en
t
VI
D
E
S- O
VI
D
EO
[Example of Menu Display Items at the Time of Input Signal RGB Selection]
p
Sub Menu
Item Name
Item Name
Image
Brightness
嘷
嘷
嘷
嘷
E-43
Contrast
嘷
嘷
嘷
嘷
E-43
嘷
嘷
E-43
嘷
嘷
E-43
嘷
嘷
E-43
In
Menu name
C
Reference
Page
Color
嘷
Tint
Sharpness
Picture Adj.
嘷
E-43
Fine Picture
嘷
E-44
H Position
嘷
E-44
V Position
嘷
嘷
Reset
Color
E-44
嘷
嘷
嘷
Quick Color Adj.
E-44
E-45
Gamma
嘷
嘷
嘷
嘷
E-45
Color Temp.
嘷
嘷
嘷
嘷
E-46
White
嘷
嘷
嘷
嘷
E-46
Color Space
嘷
E-46
嘷
White Balance
View
嘷
E-47
Aspect
嘷
嘷
嘷
嘷
E-48
Filter
嘷
嘷
嘷
嘷
E-48
Vertical Flip
嘷
嘷
嘷
嘷
E-49
Horizontal Flip
嘷
嘷
嘷
嘷
E-49
Keystone
嘷
嘷
嘷
嘷
E-49
Keystone Save
嘷
嘷
嘷
嘷
E-49
“Tint” can be adjusted only at the time of NTSC composite/S signal input.
E-41
u
om t Si
gn
R pon al
G
B en
t
VI
D
EO
SVI
D
EO
Menu Operation Method
p
Sub Menu
Item Name
Item Name
Setup
Auto Source
嘷
嘷
嘷
嘷
E-50
Auto Power Off
嘷
嘷
嘷
嘷
E-50
Menu Position
嘷
嘷
嘷
嘷
E-51
Lamp Mode
嘷
嘷
嘷
嘷
E-51
RGB
嘷
嘷
嘷
嘷
E-52
Video
嘷
嘷
嘷
嘷
E-52
S-Video
嘷
嘷
嘷
嘷
E-52
Presentation Timer
嘷
嘷
嘷
嘷
E-52
Language
嘷
嘷
嘷
嘷
E-53
On Screen
嘷
嘷
嘷
嘷
E-53
Background
嘷
嘷
嘷
嘷
E-53
Startup Screen
嘷
嘷
嘷
嘷
E-54
Security Lock
嘷
嘷
嘷
嘷
E-54
Status
嘷
嘷
嘷
嘷
E-55
Factory Default
嘷
嘷
嘷
嘷
E-55
Lamp Timer Reset
嘷
嘷
嘷
嘷
E-55
Resolution
嘷
嘷
嘷
嘷
E-56
Frequency
嘷
嘷
嘷
嘷
E-56
Lamp Timer
嘷
嘷
嘷
嘷
E-56
Input Format
Option
Info.
In
Menu name
C
Reference
Page
E-42
Image
• Perform this operation while projecting the picture for which the adjustment/setting will be made.
• Select the menu name “Image”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-41.
Brightness / Contrast / Color / Tint / Sharpness
Picture qualities such as brightness and contrast will change depending on the whether the room is bright or dark. Please adjust to suit your
preference.
Select the desired item name and then adjust with the SELECT 왗왘 buttons.
Item Name
Brightness
Contrast
Color
Tint
Sharpness
SELECT 䊴 Button
Darker
Less contrast
Less dense color
More red
Softer image
SELECT 䊳 Button
Brighter
More contrast
Denser color
More green
Sharper image
Note:
* The adjustment values of the adjustable items are stored according to input source.
* “Tint” can only be adjusted when inputting NTSC composite/S-Video signals or
component signals.
Picture Adj. / Fine Picture / H Position / V Position
Usually, automatic adjustment is performed at the time of signal selection, but when automatic adjustment is not effective, these adjustments
can be performed.
Note:
When the image extends beyond the boundaries of the screen or is smaller than the
screen, check that the “View” → “Aspect” setting is set to “Auto”. See “Aspect” on
Page E-48.
Picture Adj. (Picture Adjustment)
Adjust this when bright and dark vertical bands appear on the screen.
Select the “Picture Adj.” item name and adjust with the SELECT 왗왘 buttons
so that the vertical bands disappear and brightness becomes uniform across
the screen.
E-43
Image
Fine Picture
Adjust this when the picture shows a lack of color fidelity or flickering.
Select the “Fine Picture” item name and adjust with the SELECT 왗왘 buttons
so that the lack of color fidelity or the flickering disappears.
H Position
Adjust this when the picture is shifted to the left or right.
Select the “H Position” item name and adjust with the SELECT 왗왘 buttons.
V Position
Adjust this when the picture is shifted up or down.
Select the “V Position” item name and adjust with the SELECT 왗왘 buttons.
Reset
This function resets (i.e., returns to the standard settings) the adjustment/setting value of the “Image” menu name.
A press of the ENTER button forces the reset.
Note:
* The item name “Fine Picture” at the time of RGB input will not be reset.
* “Reset” of the menu name “Image” can be reset for each input source.
* To reset the adjustments/settings of all the menu items (while noting that there are some items that cannot be reset), see “Factory Default”
on Page E-55.
E-44
Color
• Do the following operation while displaying the image you want to adjust or set.
• Select the menu name “Color”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Pages E41.
Quick Color Adj.
Select the preset color mode.
Select the “Quick Color Adj.” item name and select the setting contents with
the SELECT 왗왘 buttons.
Color ........... Select this to prioritize color.
Standard ..... Select this to prioritize brightness.
* When “Color” or “Standard” is selected, the “Gamma”, “Color Temp.” and “White” adjustment
items are displayed in gray and cannot be selected or adjusted.
Custom ....... “Gamma”, “Color Temp.” and “White” adjustment items can be selected
and adjusted
* The selected values for the different adjustment items are stored in the memory so the desired
color adjustments can be set.
Gamma
Gamma corrects the proportion of change of the dark portions from the
bright portions of the input signal.
Set this to reproduce natural color tone or to distinctly project a personal computer picture in a bright conference room.
Select the “Gamma” item name and select the setting contents with the SELECT 왗왘 buttons.
Normal ....... Correction with standard settings
Natural ........ Corrects for natural color tones
Real ............ Corrects with emphasis on brightness
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “Gamma” adjustment item is displayed in gray and cannot be selected or adjusted.
E-45
Color
Color Temp.
The screen color is affected by the color of the illumination and other
extraneous light.
This function adjusts the white, which is the reference color for video
equipment, and improves the quality of color reproduction. Adjustment
can also be used to enhance skin colors.
Select the item name “Color Temp.” and select the setting contents with the
SELECT 왗왘 buttons.
Low ............
Medium ......
Normal .......
High ............
Produces warm whites (reddish)
Produces warm whites (yellowish)
Produces the white of sunlight
Produces cool whites (bluish)
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “Color Temp.”
adjustment item is displayed in gray and cannot be selected or adjusted. See “Quick
Color Adj.” on E-45.
White
When projecting, this function is used to emphasize the whites of text or
diagrams on the personal computer.
Select the item name “White” and use the SELECT 왗왘 buttons to select the
setting contents.
Select the desired degree of white from among “Low”, “Medium”, and “High”.
Note:
When “Color” or “Standard” is selected for “Quick Color Adj.”, the “White” adjustment item is displayed in gray and cannot be selected or adjusted. See “Quick Color
Adj.” on E-45.
Color Space
Set this function when a component signal (YPbPr) is projected and the
image is extremely red or extremely green.
Select the item name “Color Space” and use the SELECT 왗왘 buttons to
select a color space setting that provides a normal image.
Selection contents at the time of YPbPr input
BT.709, SMPTE240
Note:
* When the component signal undergoes conversion processing to red, green,
and blue which express the image of the projector, the correct color cannot be
reproduced unless a system compliant with the color difference conversion system of the input signal is used. Color Space serves to make this selection.
* The color space can only be adjusted with high definition TVs.
E-46
Color
White Balance
This function automatically adjusts the black level and the white level of
the analog RGB input signal to suit the personal computer.
1
Select the item name [White Balance] and press the ENTER button.
The display will change to [Input Black Signal].
2
The screen background color of the connected personal computer
will be set to black.
3. Press the ENTER button. The display will change to [Adjusting Black]
and the black level will be adjusted.
4
The adjustment of the black level is completed and the display
changes to [Input White Signal].
5
The screen background color of the connected personal computer
will be set to white.
6
Press the ENTER button. The display will change to [Adjusting White]
and the white level will be adjusted.
[White balance complete] is displayed for a while and the adjustment is
completed.
E-47
View
• Perform this operation while projecting the picture for which the adjustment/setting will be made.
• Select the menu name “View”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-41.
Aspect
This function sets the horizontal and vertical picture proportions of the
input signal.
Select the item name “Aspect” and select the setting contents with the SELECT 왗왘 buttons.
Personal Computer Signal
Auto ............ Automatically enlarges or reduces the image to project a full screen in a
ratio of 4:3
Direct .......... Maintains the aspect ratio and projects a picture of the maximum
displayable size
Real ............ Projects the input signal without pixel conversion
Video Signals
Auto ............ While maintaining the aspect ratio, projects a full screen so that no portions extend beyond the boundaries of the screen. The top and bottom of
the 16:9 image becomes black.
Wide ........... Projects to fill the full width with the entire image at 16:9.
(This feature is used to project a squeezed image in a proper aspect ratio.)
Zoom .......... Projects only the 4:3 portion within 16:9 image to fill the screen.
(Portion that extend off screen is cut.)
See “Selection of Aspect Ratio” on Page E-28 for diagrams of projection screen
images that correspond to the input signals.
Note:
Please note that using this monitor for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and projecting
a 4:3 screen in wide mode or leaving a squeezed screen as a compressed image
raises concern about the infringement of the copyright holder’s rights which are
protected by copyright law.
Filter
This function sets the sharpness when the input signal is adjusted to
the resolution of the projector and enlarged or reduced.
Select the item name “Filter” and select the setting contents with the SELECT
왗왘 buttons.
Smaller numerical values result in a sharper picture and larger values result in
a softer picture. Please select your desired setting value.
E-48
View
Vertical Flip
In selecting the method of projecting to the screen, these functions are
set when the projector is in a rear screen installation.
Select the item name “Vertical Flip” or “Horizontal Flip” and select the setting
contents with the SELECT 왗왘 buttons.
“Vertical Flip” Off
“Horizontal Flip” Off
“Vertical Flip” Off
“Horizontal Flip” On
“Vertical Flip” On
“Horizontal Flip” On
Keystone
Keystone distortion will occur when the projector and screen are on an
angle (in the vertical orientation). This function is used to correct this
distortion.
Select the item name “Keystone” and correct the keystone distortion using the
SELECT 왗 왘 buttons.
Press the “왗” button.
Press the “왘” button.
Note:
* The menus and other on-screen displays cannot be adjusted.
* Please note that depending on the projected picture and the projection conditions, it may not be possible to eliminate keystone distortion completely.
Keystone Save
This function is used to save the keystone adjustment values.
Setting Keystone Save to on will set the previous keystone adjustment values
when projecting after the power cable has been disconnected and then reconnected.
Select the item name “Keystone Save” and set with the SELECT 왗왘 buttons.
Off .............. The keystone adjustment values return to the initial values when the power
cable is unplugged.
On ............... The keystone adjustment values are retained in storage even when the
power cable has been unplugged.
Note:
Regardless of whether Keystone Save is set to “On” or “Off”, when projection is
from the standby condition, the picture is projected using the previous keystone
adjustment values.
E-49
“Vertical Flip” On
“Horizontal Flip” Off
Setup
• Select menu name “Setup”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-41.
Auto Source
The Auto Source function automatically detects the input signal when
the power supply is switched on and when the input is switched.
Select the item name “Auto Source” and select the setting contents with the
SELECT 왗왘 buttons.
On ............... Switches on the automatic detection function
Off .............. Switches off the automatic detection function
Signal Detection Order When On
The sequence of RGB → VIDEO → S-VIDEO is searched repeatedly.
When a signal is detected, the search is stopped and the image is projected.
Auto Power Off
This function switches off the projector power automatically when the
input of the projector enters a no-signal condition.
Select item name “Auto Power Off” and select the setting contents with the
SELECT 왗왘 buttons.
On ............... The power is switched off when there is no signal.
Off .............. The power is not switch off even when there is no signal.
Operation when Function is On
• The “No Signal Power Off” display appears when a no-signal condition continues for approximately 10 seconds. The power is switched off about 5
minutes after this.
• If a signal is input during the appearance of the display and an operation
button other than the STANDBY button is pressed, the display is closed and
the function is cancelled.
Note:
Some video decks and other equipment output a blue background or other video when playback ends. When this happens, a signal is being
input to the projector and Auto Power Off is not activated.
E-50
Setup
Menu Position
This function sets the display position of the menu.
Select item name “Menu Position” and select the setting contents with the
SELECT 왗왘 buttons.
............. Displays on the left side
............. Displays on the right side
Lamp Mode
Use this if the picture is projected on a small screen and the picture is
too bright or when projecting images in dark rooms.
Select the item name “Lamp Mode” and select the setting contents with the
SELECT 왗왘 buttons.
Eco ............. The lamp’s brightness is reduced to approximately 80%, extending the
lamp’s service life.
(STATUS indicator is green)
Normal ....... The lamp brightness is set to 100% and the screen is bright.
(STATUS indicator is off)
Note:
Frequent switching this mode can degrade the lamp.
STATUS Indicator
STANDBY
STANDBY
AUTO
SOURCE
E-51
STATUS
Setup
Input Format
This function is used in setting the input signals of the input connectors.
Normally, this should be set to Auto. When identification is not possible
with Auto, make the setting.
Select the item name “Input Format”, press the ENTER button, and the sub
menu will open.
Select the connector that is to be changed, and select the setting contents
with the SELECT 왗왘 buttons.
[RGB]
This is the signal setting for the RGB connector.
Auto ............ Automatically identifies the signal.
RGB ............ Analog RGB signal is set.
Component . Component signal is set.
[Video] and [S-Video]
[Video] is the color system setting for the VIDEO connector and [S-Video] is
the color system setting for the S-VIDEO connector.
Auto ............ Automatic identification.
NTSC .......... Fixed to the NTSC system.
NTSC 4.43 .. Fixed to the NTSC 4.43 system.
PAL ............. Fixed to the PAL system.
PAL M ......... Fixed to the PAL M system.
PAL N ......... Fixed to the PAL N system.
PAL 60 ........ Fixed to the PAL 60 system.
SECAM ....... Fixed to the SECAM system.
Presentation Timer
The presentation is given while checking the timer displayed on the
screen.
The gauge display allows the remaining time to be known at a glance.
Select the item name “Presentation Timer” and select the setting contents
with the SELECT 왗왘 buttons.
Setting contents: Off, 10 min., 20 min., 30 min., 40 min., 50 min., 60 min.
To start the timer...
Press the MENU button and open the menu.
The timer display will appear at the lower right and the timer will start.
See “Using the Presentation Timer” on Page E-32 for details.
E-52
Option
• Select menu name “Option”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-41.
Language
This function sets the language that is displayed on screen in
the messages and menu displays.
Select item name “Language” and press the ENTER button to open
the Language sub menu.
Select the language with the SELECT 왖왔 buttons.
On Screen
This function switches on/off the messages displayed with a black
frame such as the input signal information and the aspect ratio.
Select item name “On Screen” and select the setting contents with the
SELECT 왗왘 buttons.
On ............... The message is displayed.
Off .............. The message is not displayed.
Note:
Even when set to off, messages that are not in a black frame will be displayed.
Example of a display when the
ASPECT button is pressed
Wide
Background
This function sets the screen color when the input source is nosignal.
Select item name “Background” and select the setting contents with
the SELECT 왗왘 buttons.
Blue ............ Sets a blue screen when there is no signal
Black ........... Sets a black screen when there is no signal
E-53
Option
Startup Screen
This is the selection of whether or not to display the logo screen
at startup time.
Select item name “On Screen” and select the setting contents with the
SELECT 왗왘 buttons.
Logo ........... Displays the logo.
Blank .......... Does not display the logo.
Note:
When “Logo” is selected at the startup screen, the “PLUS” logo is displayed.
Security Lock
A password can be registered and the security lock set in order
to prevent unauthorized use of the projector.
For instructions on using the security function, see “Protecting the
Projector with the Security Lock” on E-33.
Select item name “Security Lock” and select the setting contents with
the SELECT 왗왘 buttons.
Disable ....... The security lock is disabled.
The projector can be operated without inputting the password.
Enable ......... The security lock is enabled.
The security lock is activated when the power is turned on, and
the password must be input in order to operate the projector.
E-54
Info.
• Select menu name “Info.”.
See “Menu Operation Method” on Page E-36 for information about performing menu operations. The item name display will
differ depending on the input signal. See “List of Item Names Offering Input Selection and Adjustments/Settings” on Page E-41.
Status
This displays information about the equipment.
Select item name “Status” and press the ENTER button.
There is a change to the status display.
Press the CANCEL button to return to the menu.
Display Contents:
Projector model, firmware version, and the internet home page address of PLUS Vision Corp.
Factory Default
This function returns the adjustments and settings of all the input sources to the standard factory default values.
Select item name “Factory Default” and press the ENTER button.
There is a change to the display [Press “ENTER” to Factory Default
Set].
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
Items that are not set to the factory default:
Projection method, Language and Lamp Timer and Security.
Lamp Timer Reset
This function resets the lamp timer. Be sure to perform the reset
operation when the lamp cartridge has been replaced.
Select item name “Lamp Timer Reset” and press the ENTER button.
There is a change to the display “Press “ENTER” to Lamp Timer Reset”.
Press the ENTER button to initialize.
To cancel, press the CANCEL button and there will be a return to the
menu.
E-55
Info.
Resolution / Frequency
This function displays the resolution and frequency of the detected input signal.
Lamp Timer
This displays the lamp timer.
This projector has an Eco mode function. The lamp life will differ between
Normal mode and Eco mode.
Lamp Life
Use only in Normal mode: approx.1500 hours
Use only in Eco mode: approx.2000 hours
* Lamp life will differ when there has been switching between the modes.
• When Lamp Life Has Been Reached
“Replace the Lamp Cartridge” is displayed on the screen for 10 seconds in
a 1-minute interval.
Please replace the lamp with a new one.
See “Replacing the Lamp Cartridge” on Page E-61 for information about
lamp cartridge replacement.
• When Over 100 Hours Have Elapsed Since Reaching Lamp Life
(Including Eco Mode)
[Warning!! System Shutdown] is displayed for 10 seconds and the power is
switched off. Pressing the STANDBY button under this condition will not
switch on the power. Please replace the lamp cartridge.
E-56
When an Indicator is Lit or Flashing
TA
N
D
B
Y
S
TA
TU
S
STATUS indicator
U
R
C
E
A
STANDBY indicator
TO
S
TA
N
D
B
Y
S
The indicators on the projector’s control panel light or flash to
notify of problems, as described below.
An indicator is also used to notify you of the currently set power
mode. See “Power Cable Connections and Switching the Power
On/Off” on page E-22.
Indicator status
STANDBY
STATUS
What you should do
Lit red
When the power is on (Lit green)
Standby (Lit amber)
STANDBY
STATUS
Lit red
Flashing amber for 60 seconds, then lit
amber
STANDBY
STATUS
Flashing red
(lit for 1 seconds/off for 1 seconds)
It is time to replace the lamp.
Replace with a new lamp cartridge.
The lamp has reached the end of its service life. The power
will no longer turn on.
The projector can be used for 100 hours after the lamp has reached
the end of its service life.
Replace with a new lamp cartridge.
The lamp cover is open.
The lamp cover is not properly mounted. Mount it properly.
Lit red
STANDBY
STATUS
Flashing red
(lit for 0.5 seconds/off for 0.5 seconds)
Lit red
STANDBY
STATUS
Flashing red
(lit for 0.5 seconds/off for 0.5 seconds)
The temperature is abnormally high.
• The temperature protector has been activated. If the room temperature is high, move the projector to a cool place. If the
projector’s internal temperature is high, check the cooling fan’s
ventilation slots and clean them if they are clogged.
• When the temperature protector is activated, the power turns
off and in some cases will not turn back on immediately. In this
case wait about 90 seconds, then try again.
The fan has stopped.
Unplug the power cable and contact a store that sells the V3-131/
V3-111 for repairs.
Lit amber
STANDBY
STATUS
Flashing red
(lit for 1 seconds/off for 1 seconds)
When the lamp has burned out during use
Flashing amber for 90 seconds, then lit
amber
When the lamp does not come on
from the start
Lit amber
STANDBY
STATUS
Flashing amber
(for several seconds)
Flashing amber
(for several seconds)
The lamp will not light.
Wait at least 90 seconds, then turn the power back on. If the problem persists, unplug the power cord and contact a store that sells
the V3-131/V3-111 for repairs.
The STANDBY button has been pressed with the lens stowed away.
The STANDBY indicator flashes for several seconds, then stops flashing, remaining lit, and the projector is set back to the standby status (with the STATUS indicator off). Press the lens lift button to raise the lens unit, then press the STANDBY
button. The power will now turn on.
The lens unit was stowed away while an image was being projected.
The projector automatically turns off, and the indicators continue to flash for 90
seconds. (The cooling fan continues to run during this time.) To turn the projector
back on, wait 90 seconds, press the lens lift button to raise the lens, then press the
STANDBY button. The power turns on.
Should an indicator be in a condition other than normal or flash at a rate other than the aforementioned, disconnect the power
cable and contact your store of purchase.
E-57
When an Indicator is Lit or Flashing
Thermal Protector
When the temperature inside the projector becomes abnormally high, the STATUS indicator flashes red (0.5 seconds on/0.5
seconds off), the STANDBY indicator is a steady red, and at the same time the temperature protector operates and switches off
the power of the projector.
Should this happen, please take the following actions.
1. Switch off the power and disconnect the power plug from the wall outlet.
2. Check the following matters and take the required measures.
When the projector is being used in a location that has a high ambient temperature, set it up again in a cool location. Check the
outflow and intake holes and clean them if they are obstructed.
3. Wait about 60 minutes until the temperature of the projector drops.
If after having performed the above matters, the problem still has not been solved, please contact your store of purchase.
E-58
Troubleshooting
Check the following matters before requesting servicing.
Problem
Power does not turn on
Reference
Page
Check
• Is the power cord plugged into a power outlet?
• Is the lamp cover properly mounted?
• Is the projector’s temperature high? To protect the projector, the power cannot be turned on when the projector’s temperature is abnormally high.
• Has the lamp reached the end of its service life?
E-57
Is a connected input selected?
Is the cable properly connected to the input terminal?
When a computer is connected, are signals being output from the computer?
Does the signal being input have a frequency usable with this projector?
Are the brightness and contrast adjusted to the minimum?
Is the STATUS indicator lit a steady red or flashing red?
When the component signal of the DVD player is connected with the RGB
connector and the image is not output, is [Input Settings] of the RGB connector properly selected?
• For a RGB input, has the picture been properly adjusted?
E-27
E-17 –20
E-56
E-65
E-43
E-57
E-52
Image is distorted
• Is the projector properly installed?
• For trapezoidal (keystone) distortion, perform keystone adjustment.
Please note that depending on the projected picture and the projection conditions, it may not be possible to eliminate keystone distortion completely.
E-26
E-30, 49
Image is out of focus
•
•
•
•
E-25
E-14 –15
E-14 –15
–
Image is not in proper position and is not displayed
properly
• For a computer input, are the horizontal and vertical positions properly adjusted?
• Does the input signal have a compatible resolution and frequency? Check
the computer’s resolution.
E-44
Video image is crushed
• If the image is crushed in the horizontal or vertical direction or if it is not
displayed over the entire screen, select a different aspect ratio.
E-28
Colors of the overall image
are strange
• When a component signal is being input, is the color space setting proper?
• For a composite input, is the tint properly adjusted?
E-46
E-43
Characters flicker or colors
are offset for RGB inputs
• From the menu, select “Image” and adjust the clock frequency and phase.
E-43, 44
Cannot select the menu
name
• Other than [Settings], [Option] and [Information], selection will not be possible unless a signal is being input to the projector and the image/picture is
projected.
–
Remote control unit does
not operate
• Are the remote control unit’s batteries worn? Replace with new batteries.
• Is there an obstacle between the remote control unit and the projector’s
remote control signal sensor?
• Is the remote control unit outside of range?
• Are you pointing the remote control unit’s transmitter towards the projector’s
remote control signal sensor?
E-12
E-12
• See “When an indicator is lit or flashing”.
E-57
No image is produced
STATUS indicator is lit red
or flashing red
•
•
•
•
•
•
•
E-22
E-63
E-57
Is the lens properly focused?
Are the screen and projector installed at the proper distance?
Does the projection distance exceed the focusing range?
Is there condensation on the lens, etc.?
If the projector is moved from a cool storage area to a warm place and the
power is turned on, condensation may form on the lens or internal optical
parts. If this happens, wait until the condensation has evaporated before
using the projector.
E-59
E-43, 44
E-65
E-12
E-12
Cleaning
• Be certain to disconnect the power plug from the power outlet before cleaning.
• Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Do not leave rubber
or vinyl products in contact with the projector for long periods. Doing so could cause them to undergo qualitative changes or the
coatings may peel, etc.
Cleaning a Soiled Projector Main Unit
• Wipe with a lint-free, soft, dry cloth.
When very dirty, wipe with a cloth that has been moistened with a diluted neutral detergent, then finish with a dry cloth. If a
chemically-treated cloth is going to be used, please follow any written warnings.
• Do not wipe with thinner, benzene, or other solvents. Doing so could cause them to undergo qualitative changes or the coatings
may peel, etc.
• When removing the dust of the outflow and intake holes, use the brush attachment on a vacuum cleaner to clean out the dust.
Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.
• Do not scratch or otherwise hit the projector body with your nails or other hard object, since this will cause scratches.
Dirty Lens
• Clean using the same method you would use to clean a camera lens: Use a commercial blower for camera use or cleaning
paper for eye glasses. Be careful not to scratch the lens at this time.
Dust of the Intake and Outflow Holes
Dust that collects in the intake and outflow holes will obstruct the ventilation and cause the internal temperature to rise which
could cause damage. Clean this area carefully. As a guideline, clean at least every 100 hours of usage.
H
S
U
P
• Switch off the power, check that the STANDBY indicator has
changed to a steadily lit amber, then unplug the power cable.
• Clean out the holes from the outside using a vacuum cleaner.
Use the brush adapter of the vacuum cleaner to do this. Avoid
using the vacuum directly without attaching the adapter as well
as the use of a nozzle adapter.
Y
B
D
N
TA
S
S
TU
TA
S
Y
B
D
N
TA
S
TO
U
A
E
C
R
U
O
S
IO
D
AU
EO
ID
S-V
EO
VID
B
G
R
Cleaning the Inside of the Projector
Cleaning of the inside of the projector is required about once a year. Failure to clean over a long period while dust has collected
inside the projector could cause a fire or breakdown. Do not clean the inside of the projector by yourself. Please be sure to contact
your dealer.
E-60
Replacing the Lamp Cartridge
• The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is
about 1500 hours (when used in normal mode only). This could be shortened depending on conditions of use and
other factors.
Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp
means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from
test conditions at this company.)
• When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp
Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the
replacement following the procedure below.
• If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode
and no longer turns on.
• Contact a store that sells the V3-131/V3-111 for a replacement lamp. Indicate you need a V3-120 replacement lamp for
the V3-131/V3-111 (order code 28-051).
CAUTION
• Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop,
disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before
replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will
cause burns because of the high temperature.
• Do not remove any screws other than those specified.
• Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.
• If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can
be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may
cause injury. If this happens, contact your dealer or the store the projector was purchased.
E-61
Replacing the Lamp Cartridge
Preparations: Turning the projector upside-down on top of a soft cloth, etc., so that it does not get scratched makes it easier to
replace the lamp cartridge. Turn the projector right-side up after replacing the lamp cartridge.
1 Unplug the power cord.
2 Turn the projector upside-down.
3 Remove the lamp cover.
(1) Turn the lamp cover’s set screw counterclockwise and
loosen until the screw turns freely. (The screw does
not come off.)
(2) Open the lamp cover a little, then pull it in the direction of the arrow and remove it.
3
1
2
4 Remove the lamp cartridge.
(1) Fully loosen the lamp cartridge’s two screws. (The
screws do not come off.)
(2) Grasp the lamp cartridge’s handle and pull upward
to remove the lamp cartridge.
E-62
Replacing the Lamp Cartridge
5 Mount the new lamp cartridge.
(1) Push the lamp cartridge in slowly.
(Line it up with the screw holes in the projector.)
(2) Turn the lamp cartridge’s two screws clockwise to
tighten them.
6 Mount the lamp cover.
(1) Set the tip of the lamp cover in place, then close the
lamp cover.
(2) Turn the lamp cover’s screw clockwise to tighten it.
1
2
7 Reset the Lamp Timer.
Connect the power cable, switch on the power, and then reset.
Select [Info.] → [Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization
verification display. Press the ENTER button again. See “Lamp Timer Reset” on Page E-55.
Note:
After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should
this happen, while the projector is in the standby mode, simultaneously holding down the projector’s SOURCE button and AUTO button for
more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared.
Contact a store that sells the V3-131/V3-111 for a replacement lamp. Indicate you need a V3-120 replacement lamp for the V3-131/V3-111
(order code 28-051).
E-63
Specifications
Model
V3-131/V3-111
Optical
Method of projection :
DMD
Lamp
Projection lens :
Image size
Light Output
Contrast Ratio
DLP™ (single chip DMD)
V3-131:
0.7 inches 1024⳯768 dots
V3-111:
0.55 inches 800⳯600 dots
120 W high pressure mercury lamp
Fixed focus, Manual focus F = 2.6, f = 23 mm (f = 0.91 inch)
V3-131:
Minimum: 36 inch (at projection distance of 1.2m(3.9 feet) )
Maximum: 300 inch (at projection distance of 10.0m(32.8 feet) )
V3-111:
Minimum: 28 inch (at projection distance of 1.2m(3.9 feet) )
Maximum: 300 inch (at projection distance of 12.8m(42.1 feet) )
V3-131:
Standard mode: 1000 lm
V3-111:
Standard mode: 800 lm
2000:1 (Full on/off)
Electrical
Inputs
Color Reproduction
Resolution
Input Current
Power Requirement
Power Consumption
Video (NTSC3.58/NTSC4.43/PAL/PAL-N/PAL-M/PAL60/SECAM/YCbCr(NTSC, PAL)/
YPbPr(480p, 576p, 1080i, 720p)): (automatic or manual switching)
RGB (Horizontal :15 to 80 kHz, Vertical 50 to 85 Hz)
Full color (16,770,000 colors)
V3-131:
VGA (640⳯480) expansion/true, S-VGA (800⳯600) expansion/true
XGA (1024⳯768) true, S-XGA (1280⳯1024) compression
V3-111:
VGA (640⳯480) expansion/true, S-VGA (800⳯600) true
XGA (1024⳯768) compression
1.8 A
100 - 240 V AC, 50/60 Hz
175 watts (165 watts in eco mode)
Mechanical
Dimensions Excluding Stand
Weight
Operational Temperatures
158 mm (W)⳯35 mm (H)⳯209 mm (D) (when stored, not including projecting parts)
6.2 in.(W)⳯1.4 in.(H)⳯8.2 in.(D) (when stored, not including projecting parts)
Approximately 1.1 kg / 2.4 lbs
Data projector: 5° to 35°C (41° to 95°F), 30 to 85% humidity
• Specifications and design are subject to change without notice.
E-64
Table of Supported Frequency
The projector automatically identifies the signal input from the computer and selects the optimum resolution as shown on the table
below.
Manual adjustments may be required for some input signals. See “Picture Adj. / Fine Picture / H Position / V Position” on page E43, 44.
Signal
VIDEO(NTSC)
VIDEO(PAL/SECAM)
VESA
Apple Macintosh
HDTV (1080i)
SDTV
(720p)
(576p)
(480p)
Resolution
ⳮ
ⳮ
640
640
720
640
640
720
720
640
640
640
640
800
800
800
800
800
1024
1024
1024
1024
1024
1280
640
823
1024
1152
1920
1920
1280
720
720
⳯ 350
⳯ 350
⳯ 350
⳯ 400
⳯ 400
⳯ 400
⳯ 400
⳯ 480
⳯ 480
⳯ 480
⳯ 480
⳯ 600
⳯ 600
⳯ 600
⳯ 600
⳯ 600
⳯ 768
⳯ 768
⳯ 768
⳯ 768
⳯ 768
⳯ 1024
⳯ 480
⳯ 624
⳯ 768
⳯ 870
⳯ 1080
⳯ 1080
⳯ 720
⳯ 576
⳯ 480
Frequency
Horizonral (kHz)
15.734
15.625
31.5
37.9
31.5
31.5
37.9
31.5
37.9
31.5
37.9
37.5
43.3
35.2
37.9
46.9
48.1
53.7
48.4
56.5
57.7
60.0
68.7
64.0
35.0
49.7
60.2
68.7
33.8
28.1
45.0
31.3
31.5
Vertical (Hz)
60.0
50.0
70.1
85.1
70.0
70.1
85.1
70.0
85.0
60.0
72.8
75.0
85.0
56.3
60.3
75.0
72.2
85.1
60.0
70.1
72.0
75.0
85.0
60.0
66.7
74.5
74.9
75.1
60.0
50.0
60.0
50.0
60.0
* The model name for XGA is V3-131 and SVGA V3-111.
* The projector does not support the ADC connector on Apple Macintosh.
Video
嘷
嘷
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
嘷
嘷
嘷
嘷
嘷
嘷
ⳮ
RGB
XGA
SVGA
ⳮ
ⳮ
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
嘷
ⳮ
嘷
嘷
嘷
嘷
ⳮ
ⳮ
ⳮ
ⳮ
ⳮ
: Supported frequency
: Not supported frequency
V3-131
The display resolution is 1024⳯768 dots. When displaying a signal with resolutions other than 1024⳯768 dots such as 1280⳯1024,
sizes of characters or lines may be uneven.
V3-111
The display resolution is 800⳯600 dots. When displaying a signal with resolutions other than 800⳯600 dots such as 1024⳯768,
sizes of characters or lines may be uneven.
E-65
Cabinet Dimensions
Unit: mm (inch)
35 (2.4)
7 (0.3)
158 (6.2)
209 (8.2)
PUSH
STANDBY
STANDBY
AUTO
SOURCE
[When projecting]
E-66
STATUS
2003
Download PDF
Similar pages